Precision marking tools for accurate setup and machining
Precision marking tools such as scribing sets and scribers are essential for laying out work in metalworking and woodworking, enabling machinists and fitters to transfer exact lines and points for drilling, milling and cutting. These tools serve to produce fine reference lines on materials like metal, wood and plastic, ensuring correct alignment and repeatable results when combined with a precision caliper or other measuring aids. Using a quality scriber, scribing set and precision caliper improves setup speed, reduces setup errors and supports consistent tolerances across batches.
300mm Steel Precision Hairline Rule Hardened Ground Lapped Edges Matt Finish Hand-Heat Shield - TECWERK
Take advantage of precise, repeatable reference measurements thanks to a hardened, lapped measuring edge and a corrosion‑resistant finish; the combination of stability, fine measuring accuracy, and low thermal influence supports consistent inspection routines. Order the item directly via Metav Werkzeuge or ask the consultants for application advice. TECWERK precision straight edge DIN 874/00, 300 mm — hardened stainless steel, 38 x 8 mm cross section TECWERK precision straight edge DIN 874/00, 300 mm is a workshop reference tool for inspection and layout work, designed for reliable flatness checks and transfer measurements in production and quality assurance Hardened and ground stainless steel blade Lapped measuring edges for accurate references Hand‑heat shield reduces thermal distortion Non‑glare matt finish for clear visibility Accurate, traceable reference measurements for quality control A hardened, flat reference blade ensures repeatable accuracy when checking surfaces and setting up machinery. The lapped measuring edges provide a true line that reduces measurement uncertainty and simplifies comparison tasks against production parts. Conformity with DIN 874 means the instrument serves as a validated workshop standard, supporting inspection workflows that require documented reference tools. This stability reduces rework and speeds up in‑line checks. Built for everyday workshop resilience and corrosion resistance The blade is manufactured from stainless steel, hardened and ground to sustain frequent handling without losing accuracy. The 38 x 8 mm cross section balances rigidity and handling convenience, allowing stable placement across small components as well as longer checks along machined edges. The matt, non‑reflective surface minimises glare under workshop lighting, improving visual contrast when comparing surfaces or using optical aids. Lower thermal influence and comfortable handling during repeated use Equipped with a hand‑heat shield, the straight edge limits the transfer of body heat to the measuring surface, which helps to preserve dimensional integrity during repeated checks. Reduced thermal drift is particularly beneficial in temperature‑sensitive routines and when working with fine tolerances. The overall design supports confident positioning and reduces the risk of measurement error caused by handling. Inspection readiness and integration into QA processes The tool is designated inspection required, ensuring it can be entered into calibration and traceability systems as part of quality assurance. As a compact, standardised reference complying with DIN 874, it integrates smoothly into calibration schedules and inspection documentation. The robust finish and lapped edges maintain performance between formal checks, delivering a reliable reference for workshop and inspection tasks. Contact Metav Werkzeuge to arrange purchase or to discuss suitability and delivery directly from our Emmerich centre, where specialist advice and product availability are provided by experienced precision partners. Technical data Article number: 2000858395NW Product: Precision straight edge Brand: TECWERK Packaging unit: 1 Core data Length: 300 mm Cross section: 38 x 8 mm Special features Stainless steel Hardened and ground Lapped measuring edges Hand‑heat shield Non‑glare matt finish DIN 874/00 Inspection required FAQ What materials is the straight edge suitable for checking? The precision straight edge is intended as a reference tool for inspecting machined surfaces and can be used when checking components made from metals and other solid materials where a flatness reference is required. How does the hand‑heat shield improve measurement reliability? The hand‑heat shield reduces heat transfer from the operator to the blade, helping the straight edge maintain its dimensional stability during repeated handling and so preserving measurement accuracy. Is the tool compliant with any standards? Yes, the instrument is produced to the requirements of DIN 874/00 and is suitable as a workshop reference for inspection tasks that require standardised measuring equipment. How often should the measuring edges be checked or re‑lapped? Edge checking intervals depend on usage and inspection schedules; the product is marked inspection required so it should be included in regular calibration and verification cycles according to internal quality procedures. What is the SKU for ordering and traceability? The article is listed under SKU 2000858395NW for ordering and record keeping. Manufacturer / Responsible: NORDWEST Handel AG, Robert‑Schuman‑Straße 17, 44263 Dortmund
300mm Steel Scale Flexible Laser‑Etched 0.5mm Division, Stainless Spring Steel - TECWERK
Take advantage of the combination of laser-etched graduations, a flexible stainless spring steel construction and a slim cross-section for reliable marking and measuring in busy workshops; order directly via Metav Werkzeuge or consult our specialists for measurement and inspection details. TECWERK 300 mm steel rule – laser-etched, flexible stainless spring steel The TECWERK 300 mm steel rule is a flexible, laser-etched measuring scale designed for workshop marking, layout work and quick dimensional checks where a slim, durable rule is required. Laser-etched mm / 1/2 mm graduations Flexible stainless spring steel construction Compact cross-section 13 x 0.5 mm Inspection required for measurement certainty Clear graduations for consistent measurement results The laser-etched mm / 1/2 mm scale provides consistently legible markings that resist wear, ensuring repeatable readings throughout the service life. Laser etching creates a permanent, high-contrast scale that supports rapid identification of dimensions and reduces reading errors in production and assembly tasks. With this level of precision, marking and transfer measurements are more reliable, helping to reduce rework and wasted material. Robust, flexible design for demanding workshop use Constructed from stainless spring steel, the rule combines corrosion resistance with elastic behaviour that allows safe use on slightly curved surfaces and in tight spaces. The slim 13 x 0.5 mm cross-section keeps the profile unobtrusive while providing sufficient stiffness for straight-edge tasks and flexibility when a small bend is required. This balance of rigidity and springiness makes it suitable for daily use in metalworking, toolmaking and general workshop environments. Built-in quality assurance and traceability The item is marked as inspection required, signalling that it must be checked to ensure measurement accuracy before critical use. The construction and permanent scale make the rule straightforward to verify with a standard caliper or gauge block; verification maintains conformity with internal quality processes and standards. This approach supports documented traceability and provides confidence when the rule is used for setting up machines or performing final checks. Practical handling and workshop integration With a length of 300 mm and a compact profile, the rule fits into tool rolls, pockets and storage trays without occupying excessive space. The durable surface treatment and flexible body reduce the risk of distortion in everyday handling, while the laser-etched markings limit the need for replacement due to wear. Supplied as a single unit, it integrates easily into tool kits and inspection sets for craftsmen and maintenance technicians looking for a dependable measuring aid. Contact Metav Werkzeuge for product availability, calibration advice and to discuss how the TECWERK 300 mm steel rule fits specific workshop workflows; email info@metav-werkzeuge.com or call +49 2822 7131930 for prompt assistance Technical Data Article number: 2000858762NW Label: Stahlmaßstab L.300mm rostfr.STA biegsam Teilung B=mm/1/2mm TECWERK Product type: Steel rule Manufacturer: TECWERK Length: 300 mm Cross-section: 13 x 0.5 mm Facts Length: 300 mm Cross-section: 13 x 0.5 mm Division: mm / 1/2 mm Special features Laser-etched scale Flexible execution Made from stainless spring steel Inspection required Packaging unit: 1 FAQ What material is the rule made from? The TECWERK 300 mm steel rule is manufactured from stainless spring steel, offering corrosion resistance and elastic behaviour suitable for workshop use. Are the graduations permanent and wear-resistant? Yes, the graduations are laser-etched so the scale remains legible and resistant to abrasion over prolonged use. Is the rule suitable for measuring curved surfaces? The flexible construction allows the rule to conform to slight curves; its 13 x 0.5 mm profile balances flexibility with useful rigidity for marking tasks. Does the product require verification before use? The product is marked as inspection required, so verification is recommended to confirm accuracy prior to critical measurements with the TECWERK steel rule. What length and division does the rule provide? The rule measures 300 mm in length and carries markings in mm / 1/2 mm for fine workshop measurements. Manufacturer / Responsible: NORDWEST Handel AG, Robert‑Schuman‑Straße 17, 44263 Dortmund
300mm Steel Scale Flexible Stainless Spring Steel Division mm/0.5mm H. PREISSER - TECWERK
Take advantage of a laser-etched metric scale combined with flexible stainless spring steel for fast, reliable linear checks on curved or flat components; order or request advice from Metav Werkzeuge for prompt supply and technical guidance. Stainless steel scale L 300 mm, flexible – steel scale by TECWERK, division mm/1/2 mm A stainless steel scale L 300 mm designed for precise linear measurement in workshops and production environments, flexible for use on curved surfaces. Laser-etched metric scale Flexible stainless spring steel 300 mm overall length Component requiring inspection Precise, repeatable readings where surfaces are irregular The laser-etched scale ensures permanently legible graduations and reduces reading errors typical of printed markings. Laser marking provides high contrast and wear resistance, so a single pass measurement on sheet metal, tubes or formed parts gives consistent results. The flexible design allows the scale to conform to slight radii, meaning fewer set-ups and quicker checks; this translates into measurable time savings in routine quality-control tasks and lower scrap rates when compared with rigid measurement aids. Robust material and clear quality controls for everyday use Constructed from stainless spring steel, the thin profile and spring temper combine resilience with the pliability required for curved measurements. The compact 30 x 1 cross-section offers a slim contact edge for accurate alignment in grooves or against profile edges. Marked as inspection required, the component is supplied ready for integration into certified workflows where traceable verification is necessary. The 300 mm length covers most bench-top checks while remaining convenient to handle and store. Integrates into workshop processes and saves time on the shop floor As a straightforward, low-complexity measuring aid, this flexible ruler is ideal for quick pass/fail checks, layout tasks and secondary verifications alongside calipers and gauges. The simple metric division mm/1/2 mm supports rapid visual comparison without conversion and fits neatly into multi-stage inspection plans. Combined with systematic use, the tool reduces downtime between setup and production, supporting a smoother workflow and allowing staff to focus on value-adding operations rather than repeated re-measurement. Contact Metav Werkzeuge for supply and application advice on the flexible stainless steel scale; technical consultants in Emmerich will recommend the right inspection workflow and arrange prompt delivery Technical data SKU: 4000858773NW Description: Stainless steel scale L 300 mm, flexible Manufacturer: TECWERK Facts Length: 300 mm Cross-section: 30 x 1 mm Scale division: mm / 1/2 mm Packaging unit: 1 Inspection required: yes Special features Laser-etched scale Flexible design Material: stainless spring steel Execution: flexible FAQ What surfaces can this flexible scale be used on? The flexible stainless scale is intended for both flat and slightly curved surfaces; the spring-steel construction allows conformance to radii while maintaining accurate metric readings. Is the marking durable against workshop wear? Yes—by virtue of the laser-etched scale, the graduations resist abrasion and remain legible under normal shop use. Does the product require formal inspection before use? The item is marked as inspection required; it is suitable for calibrated workflows where component verification and documentation are necessary. Can the scale replace a caliper for precision measurement? The scale offers quick linear checks and layout support but does not substitute for micrometre- or caliper-based dimensional control where high-precision numeric readings are required. Manufacturer / Responsible: NORDWEST Handel AG, Robert-Schuman-Straße 17, 44263 Dortmund
300mm Steel Scale Flexible Stainless Steel Graduation A mm/mm, Laser-Engraved - TECWERK
Take advantage of a compact, corrosion-resistant measuring tool that combines laser-etched mm/mm graduations, flexible stainless spring steel and a slim profile for quick, repeatable checks on small components—order the item directly via Metav Werkzeuge or consult our specialists for application advice. Stainless Steel Rule 300 mm (flexible) by TECWERK — laser-etched mm/mm graduations The Stainless Steel Rule 300 mm (flexible) is a compact, corrosion-resistant measuring scale intended for workshop measuring tasks and simple inspection work, delivering clear mm/mm graduations in a flexible format for curved or confined surfaces Laser-etched mm/mm graduations Flexible stainless spring steel Compact 300 mm measuring length Inspection-required quality control Precision where space is limited The compact 300 mm length and finely laser-etched mm/mm graduations make this measuring rule a practical choice for tight workspaces where quick, reliable linear measurement is required. The clearly marked scale reduces reading errors compared with printed alternatives; the permanent marking resists abrasion and solvent exposure, which supports consistent dimensional checks during production or assembly. For small-batch inspection and fast set-ups, the slim rule delivers accurate reads without adding bulk to the tool tray. Durable, flexible construction for everyday use Constructed from stainless spring steel, the rule combines corrosion resistance with controlled flexibility: the material bends to follow contours yet returns to its original shape, avoiding permanent distortion. This behaviour is useful for measuring slightly curved edges or internal radii where rigid gauges fail. The slim cross-section contributes to easy handling and storage while the robust metal resists dents and wear, extending service life and reducing replacement frequency. Built for traceability and shop-floor compliance Marked as inspection-required, the rule supports quality-assurance processes that demand documented verification and calibration intervals. The permanently lasered scale contributes to traceable measurement results and simplifies routine checks. Integrating this rule into calibration schedules and process control reduces uncertainty in repeated measurements and helps maintain conformity with internal inspection standards. Practical handling and workshop integration The slender profile and practical length suit everyday tasks such as checking part lengths, verifying step heights and quick comparative measurements. The tool works well alongside calipers and gauges as a low-cost precision aid for setup and first-off inspections. For additional technical details or to confirm fit for a specialised application, contact Metav Werkzeuge by e‑mail at info@metav-werkzeuge.com or by phone on +49 2822 7131930 for personalised advice and supply information. For purchase recommendations or to discuss application suitability for this flexible stainless steel rule, contact Metav Werkzeuge for fast, expert assistance from Emmerich at +49 2822 7131930 or info@metav-werkzeuge.com Technical Data Article number: 4000858771NW SKU / UID: 4000858771NW Product type: Steel rule (Stahlmaßstab) Brand: TECWERK Facts Length: 300 mm Cross-section: 30 x 1 mm Graduation: mm/mm Packaging unit: 1 Special features Material: stainless spring steel Scale: laser-etched Design: flexible Inspection-required: yes FAQ What material is the rule made from and why does it matter? The rule is made from stainless spring steel, which provides corrosion resistance and elasticity; the material choice ensures the rule remains flat after bending and is suitable for routine workshop use with the SKU 4000858771NW. How precise are the graduations on this measuring rule? The graduations are laser-etched as mm/mm divisions, offering permanent, high-contrast markings that maintain readability and support reliable comparative measurements in inspection tasks. Can the rule be used on curved surfaces? Yes, the flexible design and spring-steel construction allow it to follow slight curves while returning to flat form, making it suitable for measurements on non-flat components. Is this rule suitable for formal calibration programs? The product is inspection-required and can be incorporated into calibration and quality-assurance routines to ensure traceability and repeatable measurement results. Which workshop tasks is this steel rule best suited for? This compact 300 mm rule is ideal for quick length checks, setup measurements, and verification of small parts where a short, durable, and corrosion-resistant linear scale is needed. Manufacturer/Responsible: NORDWEST Handel AG, Robert-Schuman-Straße 17, 44263 Dortmund
300mm Universal Scriber With Prismatic Base, Adjustable Tilt, Fine Adjustment, Hardened Scribing Pin Included - Metav IndustryLine
Take advantage of the stable prismatic tool‑steel base, the fine‑adjustment mechanism and the adjustable tilt angle for reproducible, workshop‑grade scribing results; order the instrument directly via Metav Werkzeuge or consult our specialists for tailored recommendations. Universal Parallel Scriber 300 mm – prismatic tool‑steel base & fine adjustment (Metav IndustryLine) The Universal Parallel Scriber 300 mm is a marking instrument for precise, repeatable scribing and layout work across flat and cylindrical parts in metalworking and toolrooms Prismatic tool‑steel base for stable positioning Fine‑adjustment mechanism for repeatable marks Adjustable tilt angle for angled surfaces Stable support for reproducible scribing The prismatic base, manufactured from tool steel, provides a low‑play seating on round and flat components, which translates into stable support during layout operations. This stability reduces the need for repeated repositioning and ensures straight, consistent scribe lines even on awkward geometries. The solid construction keeps the reference plane constant, so every mark becomes a verifiable datum for subsequent machining steps, improving process reliability and reducing rework. Fine adjustment that improves workflow efficiency A dedicated fine‑adjustment mechanism enables micron‑level setting of the scribing point relative to the base, allowing precise offset control without continuous micro‑shimming. This feature shortens setup time and enhances throughput by making small corrections quick and exact. In practical terms, the fine adjustment converts minute manual motions into predictable, repeatable displacements—ideal for batch layout tasks where uniformity between parts is essential. Versatility for workshop and toolroom tasks The instrument’s adjustable tilt angle broadens the range of applications to include angled faces and stepped components, so the same tool can be used for diverse marking tasks. Supplied with a hardened scribing needle 130 mm, the set is ready for immediate use on typical ferrous and non‑ferrous materials encountered in maintenance, fixture building and prototype work. Robust mechanical features mean the tool performs dependably under continuous use, supporting consistent results over the long term. For precision marking with Metav IndustryLine quality, contact Metav Werkzeuge to arrange delivery or discuss which configuration best fits workshop requirements Technical Data SKU: M206.031 GTIN: 4054469102801 Customs tariff number: 90172039 Facts Base footprint: 84 x 65 x 27 mm Overall height: 327 mm Column: Ø10 x 300 mm Special features Prismatic base made of tool steel Fine‑adjustment mechanism Adjustable tilt angle Includes hardened scribing needle 130 mm Category: marking tools (Anreisszeuge) eClass: 21170129 FAQ What materials can be marked with this scriber? The Universal Parallel Scriber 300 mm from Metav IndustryLine is supplied with a hardened needle suitable for marking common workshop materials including steels and non‑ferrous alloys; surface condition and hardness of the workpiece influence mark visibility. Is the scriber ready for immediate use out of the box? Yes, the tool is delivered complete with a hardened 130 mm scribing needle so the unit from Metav IndustryLine can be used straight away for layout and marking tasks. How does the fine‑adjustment improve repeatability? The fine‑adjustment converts small dial movements into exact needle displacements, allowing the Metav IndustryLine parallel scriber (SKU M206.031) to produce reproducible offsets without repeated manual trimming. Can the base be used on cylindrical parts? The prismatic tool‑steel base is designed to sit reliably on round and flat workpieces, giving stable support for scribing on shafts, bushings and flat faces. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
300x180 mm Centre Square, Matt Chrome Finish, 1.2 kg - Metav IndustryLine
Combine robust tool steel construction with a matt‑chrome finish and a practical 300 × 180 mm layout for repeatable centring and marking operations — order the centring square directly via Metav Werkzeuge or contact our consultants for application advice. Centring square M214.174 — Metav IndustryLine centring square, matt‑chrome finish, tool steel Centring square M214.174 is a precision marking and alignment tool for workshops and production environments, designed to simplify the centring of shafts and the transfer of reference lines on metal components Robust tool steel construction Matt‑chrome reading for glare reduction 300 × 180 mm working area Suitable for shaft Ø280 mm Accurate alignment that speeds up setup The geometry of this centring square is optimised for quick, repeatable alignment of components and marking of reference lines. With a defined working area of 300 × 180 mm, the gauge provides a clear baseline for layout tasks, reducing trial measurements and setup time. The square’s rigid construction in tool steel ensures that the faces remain true under normal workshop use, keeping positional deviation low and enabling faster transitions from measuring to machining. Clear reading and durable finish for everyday use A matt‑chrome finish on the reading faces reduces reflections and aids visual contrast, which supports precise line transfer and more reliable marking. The corrosion‑resistant treatment on the base material helps maintain surface quality in workshop atmospheres, so the instrument retains its calibration and legibility over prolonged use. This combination of finish and material contributes directly to fewer rechecks and a lower risk of layout errors. Practical handling for marking and centring tasks The tool is dimensioned for common workshop tasks and is particularly suited to shaft and cylindrical workpieces up to Ø280 mm, where the geometry assists in quick determination of central axes. The robust feel and well‑defined edges make it suitable for repetitive use in marking benches and assembly stations. Because the design focuses on functionality rather than frills, maintenance is straightforward and the instrument integrates well with existing layout routines. Trusted partner for professional workshops As part of the Metav IndustryLine, this centring instrument benefits from the supplier’s emphasis on accessible precision: a wide product range, central warehousing in Emmerich and a quality filter for the European market. The Metav approach supports consistent workshop standards and reduces procurement complexity for production and maintenance teams. Choosing this instrument aligns operational needs with a supplier experienced in serving industrial and trade customers. Contact Metav Werkzeuge for tailored advice on integrating the M214.174 centring square into production workflows or to discuss compatible marking accessories — email info@metav-werkzeuge.com or call +49 2822 7131930 Technical Data Article number: M214.174 GTIN: 4054469107028 Tariff number: 90172039 ECLASS: 21170131 Facts Dimension: 300 × 180 mm Suitable for shaft diameter: Ø280 mm Special features Material: tool steel; rust‑protected; matt‑chrome reading Category: measuring instruments → marking tools Story trigger: angle/centring SKU: M214.174 FAQ What is this tool best used for? This centring square M214.174 by Metav IndustryLine is intended for precise centring, marking and alignment tasks on workshops benches and in small production runs. Which materials can be marked with the instrument? The centring square M214.174 is suitable for use on metallic components; the tool steel construction and matt‑chrome reading are designed to handle standard workshop metals. Is the tool suitable for round shafts? Yes, the geometry is appropriate for centring work on shafts up to Ø280 mm, making the M214.174 suitable for common shaft and cylindrical layout tasks. How does the matt‑chrome finish help in daily use? The matt‑chrome finish reduces glare and improves contrast on the reading faces, so lines and graduations remain easier to see under workshop lighting. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
350mm Scriber Needle For Measuring Range 350mm - TECWERK
Take advantage of a precise 350 mm marking range and robust workshop compatibility to simplify layout work and increase marking consistency; order directly via Metav Werkzeuge or contact our technical advisers for specification support. Scribing needle for 350 mm measuring range (H. Preisser) — scribing needle for workshop marking The Scribing needle for 350 mm measuring range (H. Preisser) is a precision marking tool intended for layout and transfer tasks across medium to large components in workshop environments. 350 mm marking capacity Fine, rigid scribing tip Robust workshop compatibility Compact, easy-to-handle design Accurate layout for larger components A long 350 mm measuring range enables consistent marking across broader workpieces without repeated repositioning, reducing cumulative error during layout. The elongated marking capacity is especially advantageous in metalworking and fabrication where straight, continuous scribed lines are required. By combining a fine scribing tip with a measured reach, the tool delivers reliable precision that supports repeatable workflows and lowers scrap rates. Designed for dependable workshop use Constructed for everyday use, the device offers a stable feel and controlled movement that minimise slippage during scribing. The emphasis on robustness and tactile control translates into fewer re-marks and more efficient production cycles. For operations that demand steady marking on flat or profiled surfaces, the instrument provides a straightforward, low-maintenance solution that integrates easily into standard workshop routines. Practical handling improves throughput Ergonomic handling and a compact form factor support fast, fatigue‑reduced marking over extended periods. The design permits quick alignment with gauges and rules, helping to maintain line accuracy across multiple components. Where speed and consistency matter, this scribing tool contributes to smoother measurement transfer and quicker setup times, thereby enhancing overall shop-floor productivity. Compatibility and application advice The implement is suitable for general shop marking tasks across a variety of materials commonly encountered in fabrication and maintenance. Because the unit offers a long marking span and a stable tip, it is particularly useful for transferring reference lines on panels, plates and long assemblies. If supplementary technical details are required to confirm fit or intended use, technical advisers are available to assist with application-specific questions. For precision marking solutions, trust Metav Werkzeuge: order this scribing needle via Metav Werkzeuge or contact our advisers at info@metav-werkzeuge.com or +49 2822 7131930 for application guidance and availability Technical Data Article number: 4000851748NW SKU: 4000851748NW UID: 4000851748NW Facts Measuring range: 350 mm Packaging unit: 1 Special features Product type: Scribing needle Label: Anreißnadel f.Messber.350mm H.PREISSER FAQ What materials is this scribing needle suitable for? The scribing needle is intended for general workshop marking and is suitable for common workshop materials where scribed layout lines are required; its 350 mm range supports marking on larger components. How does the 350 mm measuring range improve workflow? A 350 mm span reduces the need to reposition the marking tool when scribing long lines, improving consistency and lowering the chance of cumulative measurement error. Is the scribing needle compatible with calipers or rules? The instrument is designed for direct layout work and aligns readily with standard rules and gauges used in workshop measuring tasks for accurate transfer of reference lines. Manufacturer / Responsible: NORDWEST Handel AG, Robert‑Schuman‑Straße 17, 44263 Dortmund
400mm Precision Scriber Caliper T-Style, 160mm Stop, Hardened Matt Chrome Steel, Analogue 0.05mm Resolution, Supplied in Case - Metav IndustryLine
Take advantage of precise layout capability, robust construction and a convenient transport case to improve workshop throughput; order directly via Metav Werkzeuge or consult our specialists for application guidance. Precision Scribing Caliper M201.143 – 400 mm T‑form, 160 mm stop (Metav IndustryLine) The Precision Scribing Caliper M201.143 is an analogue, T‑form layout instrument designed for accurate scribing and dimensional control in toolrooms, fixture assembly and mould making across medium‑sized components. Precision analogue readout 0.05 mm resolution Hardened special steel, matt chrome finish T‑form with 160 mm scribing stop Fine‑adjustment screw for controlled setting Accurate layout for medium assemblies The 400 mm measuring span classifies this instrument as a medium‑range caliper, offering the best compromise between reach and rigidity for workshop tasks such as fixture set‑up, housing checks and mould alignment. The analogue 0.05 mm graduation places the tool within the industrial standard for mechanical calipers, allowing reliable transfer of nominal dimensions during layout. The T‑shape geometry provides a stable datum plane and improved leverage when scribing along edges, which reduces motion-induced error compared with conventional straight‑jaw designs. Controlled movement for repeatable marking A dedicated fine‑adjustment screw ensures that the scriber or marking point can be positioned smoothly and held without backlash, preserving repeatability across multiple parts. The robust carriage glides on hardened guides and the matt chrome surface reduces glare while resisting shop wear. This combination of controlled feed and hardened contact surfaces reduces variation in successive marks, supporting faster downstream machining and quality checks — a direct efficiency gain for production workflows. Built for shopfloor durability and clear handling Constructed from hardened special steel with a matt‑chromed finish, the scribing caliper stands up to typical workshop environments where oils, chips and repeated handling occur. The T‑form configuration with a 160 mm stop converts into a practical layout tool for operations that need fixed offset scribing or repeat stops for patterns and multiple identical components. The analogue scale and solid frame make the instrument simple to maintain and straightforward to inspect during routine metrology audits. Delivery and application notes that matter The caliper is supplied in a transport case to protect the instrument during shipping and temporary storage; the case is designed for safe handling rather than long‑term bench storage. As an analogue medium‑range layout instrument it integrates readily into production and inspection routines where mechanical robustness and simple, verifiable readings are preferred. For workshop planners, this instrument reduces set‑up time for jigs and provides a durable solution for repeated marking tasks. For detailed technical advice or to discuss suitability for specific fixtures, contact Metav Werkzeuge in Emmerich — email info@metav-werkzeuge.com or call +49 2822 7131930 to request a tailored quotation based on the 400 mm T‑form precision caliper Technical data SKU: M201.143 GTIN: 4054469100753 ECLASS: 21170344 Tariff number: 90173000 Manufacturer: Metav IndustryLine Facts Measurement range: 0–400 mm Main stop / bridge: 160 mm Resolution / graduation: 0.05 mm Instrument type: analogue Weight: not specified due to data variance Special features Material: special steel, hardened and matt chrome‑plated Design: T‑form layout caliper with scribing stop Adjustment: fine‑adjustment screw for precise setting Delivery: supplied in a transport case for protection during transit Bridge length: 160 mm FAQ What range does the caliper cover and for which applications is it suited? The caliper covers 0–400 mm and is suited to medium‑range layout tasks such as fixture set‑up, mould and housing checks where a balance of reach and stiffness is required; the T‑form aids edge scribing. What degree of accuracy can be expected from this analogue instrument? With a 0.05 mm graduation the instrument meets the industrial standard for mechanical calipers, providing dependable repeatability for shopfloor layout and marking. Is the caliper supplied ready for use and how is it protected in transit? The tool is delivered in a protective transport case to safeguard the instrument during shipping; the case facilitates safe handling between storage and the workplace. Which material and surface finish ensure the caliper's durability? The frame is manufactured from hardened special steel with a matt chrome finish, offering resistance to wear and reduced surface glare for clear readings. Does the caliper include any fine adjustment for precise scribing? Yes — the unit features a fine‑adjustment screw that allows controlled positioning of the scribing point and secure clamping for repeat marks. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
400mm Scriber Caliper With Roller, Replaceable Carbide Scriber, 0.1mm Resolution, Stainless Steel Case - Metav IndustryLine
Take advantage of a robust layout tool that combines a 400 mm measuring range, clear 0.1 mm vernier reading and a replaceable carbide scribing tip for repeatable workshop marking. Order via Metav Werkzeuge or contact our consultants for application advice and procurement support. Scriber Caliper M201.154 — 400 mm stainless-steel analogue caliper with marking roller and locking screw (Metav IndustryLine) The Scriber Caliper M201.154 is an analogue layout caliper with an integrated marking roller and a replaceable carbide scriber, designed for metalworking layout, fixture setup and general workshop marking tasks. Medium class: 400 mm measuring range Analogue vernier with 0.1 mm graduation Replaceable carbide scribing tip Stainless-steel frame, matt chrome finish Fast, reliable layout for metalworking The instrument is built for efficient marking and checking of components. The integrated marking roller allows consistent scribe lines along workpieces, while the replaceable carbide scribing tip provides a durable, repeatable contact point for layout tasks. With a clear analogue vernier graduated at 0.1 mm, the caliper suits general workshop use where rapid, robust measurements and visible scribes matter more than sub‑micrometre inspection. This combination reduces rework and speeds up set‑up for machining and assembly operations. Workshop-grade measuring range with practical stiffness Classified in the medium range (max 400 mm), the caliper balances reach and rigidity for everyday engineering tasks. Medium-range instruments are the preferred compromise for machine shops because they cover common part sizes—such as fixtures, housings and larger components—without becoming unwieldy. The solid stainless frame and matt chrome finish maintain straightness over the full span, supporting repeatable measurements and stable marking along the entire measuring length. Robust construction, simple handling Durability and ergonomics are prioritised: the matt‑chromed stainless-steel body resists workshop wear, while the locking screw secures settings for transferred marks and repeated cuts. The carbide scribing tip resists bluntness on tough surfaces and can be replaced quickly to restore crisp marking. These features deliver dependable performance with minimal maintenance, so layout operations stay efficient and downtimes are reduced. Suited applications and benefits The caliper is primarily intended for layout and marking in metal fabrication, toolroom work and general engineering benches where visible scribe lines and reliable span measurement are required. Compared with fine laboratory callipers, the emphasis here is on pragmatic benefits: faster marking, durable contact points and a reach that covers most workshop parts. The result is fewer measurement steps, clearer transfer of reference lines and a smoother workflow between setup and machining. Contact Metav Werkzeuge for tailored technical advice and to arrange supply of the Metav IndustryLine Scriber Caliper M201.154 for workshop layout and marking tasks Technical data Article number: M201.154 GTIN: 4054469100784 SKU: M201.154 Numbers / Core technical data Measuring range: 0–400 mm Graduation / vernier: 0.1 mm Weight: 0.3 kg Tariff code: 90173000 Special features / Versions Analogue vernier caliper Integrated marking roller Replaceable carbide scribing tip Locking screw for secured settings Material: stainless steel, matt chrome finish Classification: Medium range (300–500 mm) FAQ What measuring range does the caliper cover? The caliper covers a measuring range of 0–400 mm, making it a medium‑range instrument suitable for many workshop and fabrication tasks. How fine is the reading on this analogue caliper? The analogue vernier provides a 0.1 mm graduation; this is suitable for robust workshop measurements and layout rather than sub‑micrometre inspection. Is the scribing tip durable and replaceable? Yes. The product features a carbide scribing tip that is wear‑resistant and can be exchanged to restore a sharp, reliable mark. Can the caliper hold a set measurement for repeated marking? A locking screw secures the jaws, enabling the transfer of fixed settings and repeated scribing without drift. Which workshop tasks is this caliper intended for? The caliper is aimed at layout and marking in metalworking, toolrooms and general engineering where visible scribe lines and a robust measuring span are required. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
400x240 mm Centre Square Matt Chrome Finish, mm Scale - Metav IndustryLine
Take advantage of a robust tool-steel design with a matt-chrome reading surface and a practical 400 x 240 mm format for reliable centre alignment; benefit from corrosion protection and a lightweight 1.2 kg build for easy handling. Order the centring square directly via Metav Werkzeuge or consult our advisors for application-specific guidance. Centring square M214.175 — 400 x 240 mm, matt chrome-plated (Metav IndustryLine) A centring square M214.175 designed for precise marking and alignment of shafts and workpieces in metalworking and machine shops, suitable for repeatable centre-finding tasks. Matt-chrome reading for clear marking Tool steel core with rust protection Size 400 x 240 mm for shaft alignment Lightweight at 1.2 kg for easy handling Consistent centre marks with minimal setup The square’s stable geometry and tool steel construction deliver consistent results when transferring centrelines or setting up components. The matt-chrome finish on the scale reduces glare and improves contrast, making graduations easier to read under workshop lighting. For machinists and layout technicians this translates into fewer re-measures and more predictable setup times, which supports efficient workflow and reduced rework in batch or single-part production. Built to withstand workshop conditions Corrosion-resistant treatment and a durable steel body mean the device retains its mechanical integrity even in demanding environments. The combination of rust protection and a matt-plated reading face reduces wear on the graduations, preserving legibility over time. As a result, layout and scribing tasks remain accurate across many cycles of use, supporting steady inspection intervals and lower lifecycle costs for the tooling equipment. Practical size and handling for shaft alignment With a measurement area of 400 x 240 mm and a mass of 1.2 kg, the instrument balances reach with manoeuvrability for jobs such as aligning or marking shafts up to Ø400 mm and medium-sized housings. The format is compact enough for bench work yet offers the surface contact area required for reliable alignment on cylindrical parts. This makes it well suited for workshop marking, preparatory layout for machining and general assembly checks. Contact Metav Werkzeuge today for tailored advice and reliable supply of the Metav IndustryLine centring square M214.175 — precise marking tools, delivered from Emmerich to your workshop Technical Data Article number: M214.175 GTIN: 4054469107035 Weight: 1.2 kg Size: 400 x 240 mm Tariff number: 90172039 Core specifications Measurement range: 400 x 240 mm Weight: 1.2 kg Material finish: matt chrome-plated Special features Material: tool steel, rust-protected Suitable for shaft Ø400 mm Category: Marking tools (Anreisszeuge) FAQ What measurement range does the tool cover? The centring square M214.175 covers a measurement area of 400 x 240 mm, suitable for a wide range of medium-sized layout tasks. What material and finish are used? The device is manufactured from tool steel with rust protection and a matt-chrome finish on the scale for durable, low-glare readings. Is the instrument suitable for shaft alignment? Yes — the design is appropriate for aligning and marking shafts up to Ø400 mm and provides stable contact for repeatable centre transfers. How heavy is the unit and how does that affect handling? At approximately 1.2 kg the tool is light enough for manual handling while offering sufficient mass for steady placement during marking operations. Which product family and SKU does this belong to? This marking instrument is part of the Metav IndustryLine range, sold as the centring square M214.175 (SKU: M214.175). Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
500mm Digital Punch Caliper With 50x40mm Scriber Plate And Adjustable Scriber, 0.01mm Resolution, Stainless Steel - Metav IndustryLine
Take advantage of the combination of 0.01 mm digital resolution, a 500 mm measuring range and a robust stainless steel frame for dependable, repeatable marking and measurement on medium-format components; order directly via Metav Werkzeuge or consult our specialists for tailored advice. Digital marking caliper 500 mm, scribing plate 50 x 40 mm — Metav IndustryLine digital scriber with adjustable scribing needle Digital marking caliper 500 mm, scribing plate 50 x 40 mm designed for precise scribing and dimension checking in machine shops and jig production 500 mm measurement range 0.01 mm digital resolution Adjustable scribing needle Robust 15 x 6 mm measuring bar included Precision and repeatability for medium‑format work The caliper is classified as a medium‑range caliper (300–500 mm), which balances reach and rigidity for tasks such as fixture set‑up, housing inspection and medium‑sized assemblies. The 0.01 mm resolution on the digital readout delivers clear numeric feedback suitable for routine quality control, while the stainless construction minimises flex and ensures stable zeroing across the full travel. This combination reduces rework by improving first‑pass accuracy and speeds up routine marking operations by making measurements immediately readable. Clear marking and durable construction for daily workshop use Built with a stainless steel frame and a metal display housing, the scriber is engineered for workshop conditions where robustness matters. The integrated scribing plate (50 x 40 mm) and the movable scribing needle (5 x 60 mm) allow consistent, repeatable score lines on parts; the adjustable needle means different needle positions can be used without swapping tools. The instrument arrives with a solid 15 x 6 mm measuring bar and is supplied in a protective case for secure transport and storage, supporting safe handling between job sites or workstations. Efficient data handling and straightforward operation The digital readout is equipped with ON/OFF, ZERO, UNIT and HOLD functions to simplify measurement routines and reduce transcription errors. The device runs on a 3 V supply and includes an RB 5 data output for connection to compatible data loggers or CNC interfaces where traceable electronic capture is required. These features streamline inspection workflows and make the tool a practical choice for production environments that value speed and traceability over purely analogue methods. Contact Metav Werkzeuge for a bespoke quotation or technical clarification on the Metav IndustryLine marking caliper and to confirm delivery options from our Emmerich site Technical Data Article number: M240.153.1 GTIN: 4054469178387 Weight: 0.6 kg Material: stainless steel with metal housing Measurement range: 0–500 mm Resolution: 0.01 mm (0.0005 in) Power: 3 V Included accessory: solid measuring bar 15 x 6 mm Scribing plate: 50 x 40 mm Scribing needle: 5 x 60 mm Facts Measurement range: 0–500 mm Display resolution: 0.01 mm Weight: 0.6 kg Scribing needle dimensions: 5 x 60 mm Scribing plate dimensions: 50 x 40 mm Special features Digital display with ON/OFF, ZERO, UNIT, HOLD Adjustable/movable scribing needle RB 5 data output Supplied in transport case (plastic or wooden) Category: marking tools (Anreisszeuge) FAQ What makes this marking caliper suitable for workshop measurement tasks? The marking caliper combines a 500 mm measuring range with a 0.01 mm digital readout and a stiff stainless frame, providing reach and repeatability that suits fixture work, medium components and assembly checks; these attributes make the tool well matched to everyday workshop measurement tasks. Is the scribing needle adjustable and replaceable? Yes, the instrument features an adjustable scribing needle (5 x 60 mm) that can be positioned as required for different marking depths and geometries, and the needle can be serviced or replaced without changing the whole caliper. Can measurement data be exported from the caliper? Data export is available via the RB 5 output, allowing measured values to be recorded electronically when connected to compatible data acquisition systems or inspection software. Does the caliper include any accessories for handling or transport? The caliper is delivered with a solid 15 x 6 mm measuring bar and is supplied in a protective transport case to safeguard the tool during storage and movement between workstations. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
500mm Precision Ruler Hardened and Ground Lapped Measuring Edges Matt Finish Hand Heat Shield - TECWERK
Take advantage of a hardened and ground measuring tool with lapped edges and hand‑heat protection to ensure consistent straightness and reliable inspection results; order directly via Metav Werkzeuge or consult our specialists for application advice. TECWERK 500 mm precision straightedge (DIN 874/00) — hardened special steel, lapped edges The TECWERK 500 mm precision straightedge is a workshop and inspection tool designed for layout, straightness checks and comparative measurement tasks in industrial environments. Stainless special steel construction Hardened and precision ground Lapped measuring edges for accuracy Hand‑heat protection; non‑glare matt finish Consistent straightness for dependable inspection results A precision straightedge produced to DIN 874/00 standards provides a stable reference for alignment and visual inspection. The 500 mm length and 46 x 10 mm cross‑section deliver a balance between rigidity and manoeuvrability, enabling repeatable checks on components and assemblies. The lapped measuring edges reduce local surface irregularities that can falsify results; lapping is a fine‑abrasive process that produces an ultra‑flat edge, which in turn improves the precision of gap and run‑out assessments. For fabricators and inspection technicians, this means fewer ambiguous readings and faster decision making during setup and quality control. Built for wear resistance and comfortable handling Manufactured from stainless special steel and hardened and ground across its working surfaces, the tool resists wear and retains straightness under normal workshop conditions. The hand‑heat protection prevents direct transfer of body heat to the measuring edge during use, reducing thermal distortion that can affect accuracy during prolonged handling. A non‑glare matt finish improves visibility under shop lighting and minimises distracting reflections when aligning edges or comparing surfaces. These features combine to reduce the need for frequent adjustment and to preserve the integrity of the reference surface over time. Traceability, inspection status and suitable applications This straightedge is marked as inspection required, indicating that it must be examined or verified at prescribed intervals to maintain metrological trust. The tool is therefore well suited for layout benches, incoming part inspection, jig checks and calibration tasks within a quality management system. Its robust cross‑section makes it practical for use on machine beds and assembly fixtures, while the moderate length supports both bench and portable inspection work. Supplied by a recognised brand, the unit supports documented inspection routines and contributes to process reliability in production and maintenance environments. Contact Metav Werkzeuge in Emmerich for availability and technical advice: call +49 2822 7131930 or email info@metav-werkzeuge.com to discuss the TECWERK 500 mm precision straightedge and its suitability for specific inspection tasks Technical data Article number: 2000858396NW SKU: 2000858396NW Product type: precision straightedge Brand: TECWERK Packaging unit: 1 Core measurements Length: 500 mm Cross‑section: 46 x 10 mm Special features Material: stainless special steel Hardened and ground Measuring edges lapped Hand‑heat protection Non‑glare matt finish Inspection required FAQ What is the primary use of this straightedge? The TECWERK 500 mm precision straightedge is intended for layout, visual straightness checks and comparative measurement tasks in workshop and inspection environments. How does the lapped edge improve measurement quality? Lapped measuring edges reduce microscopic surface irregularities; this produces a flatter reference surface and leads to more reliable gap and run‑out assessments when using the straightedge. Is the straightedge suitable for portable inspection work? Yes, the 500 mm length and the 46 x 10 mm profile provide sufficient rigidity while remaining portable for bench and on‑machine checks. What does "inspection required" mean for routine use? "Inspection required" indicates the tool must be examined or verified at defined intervals to ensure measurement validity; this supports traceability within a quality management process. Does the finish prevent glare during visual alignment? The non‑glare matt finish reduces reflections under shop lighting, improving clarity when aligning edges or conducting visual comparisons. Manufacturer / Responsible: NORDWEST Handel AG, Robert‑Schuman‑Straße 17, 44263 Dortmund
500mm Precision Scriber Caliper T-Form 160mm Stop, Hardened Matt Chrome Finish, Case - Metav IndustryLine
Take advantage of a robust T‑head layout and fine adjustment for repeatable scribing over a medium‑range measuring span; the combination of hardened, matt chrome‑plated special steel and analogue nonius reading provides dependable workshop performance. Order the caliper directly via Metav Werkzeuge or consult the team for specification advice. Precision scribing caliper (T‑head) 500 mm, 160 mm stop — Metav IndustryLine The Precision scribing caliper (T‑head) 500 mm is a medium‑range layout instrument designed for precise marking and inspection tasks in toolmaking, fixture construction and general mechanical workshops. T‑head design for stable scribing and layout Fine adjustment for controlled, repeatable markings Hardened special steel with matt chrome finish Stable layout and reproducible markings for production tasks The T‑head format with a fixed 160 mm stop ensures stable contact when transferring datum lines or checking assembly interfaces, which reduces setup time and rework. The built‑in fine adjustment screw enables careful micro‑alignment of the scriber or jaw before committing a mark, so each setting is repeatable and reduces human error. With an analogue nonius scaled to 0.05 mm, the tool offers a clear, mechanical indication of position that is well suited to standard workshop quality control and layout work. Durable construction that keeps wear and measurement drift low Constructed from hardened special steel and finished in matt chrome, the instrument resists corrosion and abrasive wear while maintaining precise jaw geometry. The material choice and surface treatment protect the scale and sliding surfaces against everyday shop contaminants, which preserves accuracy and extends service intervals. Classified as a medium‑range caliper (measuring up to 500 mm), the design balances stiffness and reach to permit reliable measurements on assemblies and larger components without sacrificing handling. Practical uses and workflow benefits across trades The scribing caliper is tailored for workshop tasks where clear datum transfer and durable, mechanical operation are priorities: marking blanks, checking fixture references, and pre‑setting assembly contacts. The analogue operation requires no batteries and supports quick visual comparison during repetitive tasks, helping to maintain a steady throughput. Delivered in a transport case (plastic or wooden) for protection during transit, the tool is ready for immediate use on the bench or in a tooling cupboard. For layout and marking operations that demand mechanical reliability, choose the Metav IndustryLine precision scribing caliper and contact Metav Werkzeuge for technical advice and rapid supply from Emmerich. Technical data Article number: M201.144 GTIN: 4054469100760 ECLASS: 21170344 TARIC (HS) code: 90173000 Core specifications Measuring range: 0–500 mm Maximum measuring span: 500 mm Reading/Resolution: 0.05 mm (analogue nonius) Stop length: 160 mm Special features T‑head design (layout/scribing) Fine adjustment screw for controlled setting Hardened special steel, matt chrome‑plated Analogue operation (nonius) Supplied in transport case (plastic or wooden) FAQ What is the measuring range and classification of this caliper? The caliper covers 0–500 mm and is classified as a medium‑range precision instrument suitable for larger workshop layout and fixture work. How fine is the reading and what accuracy can be expected? The analogue nonius provides a resolution of 0.05 mm; this level of detail is appropriate for industrial workshop standards and repeatable layout tasks. Is the instrument delivered ready for use and protected for transport? Yes, the caliper is supplied in a transport case (plastic or wooden) and arrives ready for workshop use. Which materials is the caliper suitable for when used as a scribing and layout tool? The device is intended for workshop layout across common workshop materials; its hardened steel construction and finish ensure resistance to wear during routine marking and inspection tasks. Does the caliper include any fine‑setting feature for precise marking? A dedicated fine adjustment screw is fitted to enable controlled, repeatable positioning of the jaw prior to scribing or marking. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
500mm Scriber Needle For Height Marking Device, Solid Carbide - TECWERK
Reliable, repeatable layout lines and extended service life follow from the combination of a solid carbide marking tip and direct compatibility with 500 mm height gauges; benefit from reduced rework and steady marking accuracy in daily workshop use. Order the item directly via Metav Werkzeuge or consult the Metav team for technical confirmation and availability. TECWERK Scribing Pin (solid carbide) for 500 mm height gauges TECWERK scribing pin — a carbide marking pin engineered for precise layout work on height gauges with a 500 mm measuring range. Solid carbide tip for high wear resistance Compatible with 500 mm height gauges Precision ground for repeatable marking Single-piece, industrial workshop quality Consistent marks through carbide durability The solid carbide tip (HM) provides a hard, abrasion-resistant contact point that preserves tip geometry under frequent use. That hardness translates into stable precision and minimal wear, which reduces the need for retouching reference lines and lowers production interruptions. A carbide scribing element keeps line thickness and position predictable, supporting quality control processes and shortening layout time on subsequent machining or inspection stages. Seamless integration with 500 mm height gauges for reliable layout Designed for use with height-scribing devices, the pin matches the 500 mm measuring range and allows a direct transfer of a datum line from the gauge to the workpiece. The interface to the measuring tool ensures mechanical fit and alignment, so setting reference heights is faster and more consistent. This compatibility improves traceability in processes where repeatable positional markings are essential and supports efficient setup across batch production. Workshop-ready design that simplifies routine use Built as a single, robust component for industrial environments, the scribing pin delivers repeatability with minimal maintenance. The carbide tip resists deformation during normal layout operations, enabling longer intervals between replacements and consistent sighting on metal surfaces. For workshops aiming to streamline tooling, the combination of durability and straightforward mounting reduces downtime and supports predictable throughput without complex upkeep or calibration rituals. For precise marking in production, request the TECWERK scribing pin from Metav Werkzeuge to confirm suitability for existing measuring equipment — contact Metav Werkzeuge at info@metav-werkzeuge.com or +49 2822 7131930 to discuss availability and compatibility. Technical data Article number: 2000851586NW Label: Anreißnadel f.Messber.500mm HM z.Höhenanreißgerät TECWERK Product type: Scribing pin Facts Measuring range: 500 mm Packaging unit: 1 UID: 2000851586NW Special features Solid carbide tip (HM) For height gauges / height scribing devices Industrial workshop application Brand: TECWERK Single-item packaging FAQ What materials is the TECWERK scribing pin suitable for? The TECWERK scribing pin (product type: scribing pin, SKU 2000851586NW) is intended for routine scribing on typical workshop metals; the solid carbide tip resists wear when used on ferrous and non-ferrous surfaces in layout tasks. How does the carbide tip affect marking quality? A solid carbide tip maintains its geometry longer than softer materials, so the TECWERK scribing pin produces consistent line width and position, reducing rework and ensuring repeatable layout results. Can this pin be used with other height gauges? Compatibility is intended for height gauges with a 500 mm measuring range; the TECWERK scribing pin fits standard interfaces for height-scribing devices, but confirm dimensional fit with the gauge manufacturer where unusual mounting geometries exist. What maintenance does the scribing pin require? Maintenance is minimal: keep the tip clean and inspect for bluntness. When the carbide tip shows visible wear or deforms, replace the TECWERK scribing pin (2000851586NW) to preserve marking accuracy. Manufacturer / Responsible: NORDWEST Handel AG, Robert-Schuman-Straße 17, 44263 Dortmund
500mm Stainless Flexible Steel Scale Division B mm/1/2mm, Laser Marked - TECWERK
Take advantage of the clear, laser‑etched scale, the flexible stainless spring steel construction and the compact 18 x 0.5 mm cross‑section for reliable workshop measurement; order the item directly via Metav Werkzeuge or contact our consultants for advice on suitability and inspection requirements. TECWERK Stainless Flexible Steel Rule L 500 mm — laser‑etched mm/½ mm division The TECWERK Stainless Flexible Steel Rule L 500 mm is a laser‑etched, flexible measuring rule designed for precise linear measurement in workshops, inspection benches and maintenance tasks. Laser‑etched scale for clear, precise readings Flexible stainless spring steel construction Cross-section 18 x 0.5 mm for stable handling 500 mm measuring length with mm/½ mm divisions Clear readings that speed up work and reduce errors The laser‑etched scale delivers permanently legible graduations that resist wear and solvent exposure, ensuring consistent measurements over time. With a mm/½ mm division, the scale supports both coarse and finer readings without interpretation issues, which improves part fitting and reduces rework. Using a permanently marked measuring surface eliminates the need for frequent replacement and keeps throughput steady. Flexible construction for curved surfaces and compact storage Made from stainless spring steel, the measuring strip combines flexibility with sufficient rigidity for steady handling. The 18 x 0.5 mm cross‑section offers a narrow profile that is easy to position in confined spaces while retaining flatness when extended. This balance of bendability and stability makes the rule suitable for measuring pipes, pressed parts and other slightly curved components without sacrificing accuracy. Inspection‑ready for regulated environments This measuring rule is listed as subject to inspection, making it suitable for quality control and regulated workshop processes where traceability matters. The construction and marking method support routine verification; the durable scale remains readable throughout repeated calibrations. The combination of inspection suitability and robust materials supports compliance in production and maintenance workflows. Practical integration and reliable sourcing from Metav The product arrives as a single unit with a compact profile that slots easily into tool rolls, pockets or instrument cases. As part of Metav’s range, the rule benefits from the company's quality filter in Emmerich: decades of precision expertise, a broad catalogue and dependable supply chains. For technical clarifications or specification checks, Metav Werkzeuge provides direct support and can advise on verification intervals and storage recommendations. Contact Metav Werkzeuge for tailored advice and reliable supply of the TECWERK stainless flexible steel rule; our consultants in Emmerich will assist with inspection information and order handling Technical data Article number: 2000858763NW SKU: 2000858763NW Product: Stainless flexible steel rule Brand: TECWERK Length: 500 mm Cross-section: 18 x 0.5 mm Division: mm / ½ mm Material: stainless spring steel Scale: laser‑etched Flexible: yes Subject to inspection: yes Packaging unit: 1 Facts Length: 500 mm Cross-section: 18 x 0.5 mm Division spacing: mm / 0.5 mm Packaging unit: 1 Special features Laser‑etched scale Flexible execution Stainless spring steel material Suitable for curved surfaces Inspection‑ready (subject to verification) FAQ What material is the measuring rule made from? The TECWERK stainless flexible steel rule is manufactured from stainless spring steel, providing corrosion resistance and elastic behaviour suitable for workshop use. Is the scale durable for frequent workshop use? Yes, the laser‑etched graduations on the TECWERK steel rule remain legible under heavy use and during routine verifications, minimising the need for replacement. Can the rule measure curved surfaces accurately? The flexible construction and slim 18 x 0.5 mm profile allow the rule to conform to slight curves, enabling practical measurement of pipes and shaped parts while maintaining readable graduations. Does this measuring rule require calibration or verification? The item is marked as subject to inspection, so it is intended for environments where regular verification or calibration is required to maintain traceability and compliance. What is the smallest readable division on the scale? The scale is divided in mm with ½ mm subdivisions, which supports both standard and finer linear readings for many workshop tasks. Manufacturer/Responsible: NORDWEST Handel AG, Robert‑Schuman‑Straße 17, 44263 Dortmund
500mm Steel Rule 40 x 8mm GG1 Precision Ground, Checkable - TECWERK
Take advantage of a precisely ground steel measuring edge with verified GG1 accuracy and a compact 500 mm length for reliable workshop inspection tasks; order directly via Metav Werkzeuge or consult our technical team for application guidance. Straight edge DIN 874/I — 500 mm steel precision ruler (TECWERK) The Straight edge DIN 874/I, 500 mm is a precision measuring straight edge for workshop inspection and layout duties, designed for accurate reference checks and routine quality control. Precisely ground steel edges for accurate reference Conforms to DIN 874/I with GG1 inspection class Robust 40 x 8 mm cross-section for stability Inspection-required component for traceable measurement Accurate reference: consistent planar straightness for quality control This straight edge delivers a stable and repeatable reference line thanks to its finely ground bearing faces and honed edges. The DIN 874/I specification ensures the tool meets a defined tolerance band, while the GG1 classification indicates the inspection regime and suitability for workshop checks and comparative measurements. For users requiring objective evidence of conformity, the inspection requirement provides traceability and supports internal quality records. The compact 500 mm length makes it ideal for component-level checks where a full-length beam would be impractical, combining portability with metrological reliability. Durable construction: steel body engineered for everyday workshop use Constructed from hardened steel with a cross-section of 40 x 8 mm, the straight edge resists bending and delivers consistent contact over its working surface. The combination of high-edge and flat-side finishing reduces setup variation when used against parts or surface plates. A stainless version is noted as available short-term from factory stock for environments where corrosion resistance is required. Regular light cleaning and correct storage preserve the fine bearing faces and extend the service life of the tool, ensuring sustained measurement performance in busy production or maintenance environments. Measurement standardisation and inspection compliance for confidence The tool's GG1 accuracy class and the stated inspection obligation mean it is supplied within a documented quality framework; the inspection status confirms that the straight edge has been assessed against the DIN 874/I criteria. In practice, this reduces doubt during go/no-go assessments and supports reproducible machining or assembly operations. For teams less familiar with metrology terms: GG1 denotes a workshop grade verified by inspection procedures, offering a measured balance between affordability and precision suitable for many industrial applications. Practical advantages for workshops and quality teams A compact, precision-ground straight edge simplifies everyday tasks such as checking flatness, aligning fixtures, and verifying small assemblies. Its manageable length and sturdy profile make it useful at the bench and on machine tools alike, providing a quick visual and tactile reference. Combined with a clear inspection status, the instrument supports routine calibration cycles and helps maintain process control. As a component in a pragmatic metrology kit, it complements surface plates, feeler gauges and dial indicators to form a reliable set for routine inspection and setup tasks. For dependable workshop measurement and supply from Emmerich, contact Metav Werkzeuge for tailored advice and immediate availability — email info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: 4000858822NW Name: Lineal DIN874/I L.500mm STA H.PREISSER Product type: Straight edge / ruler Facts Length: 500 mm Cross-section: 40 x 8 mm Accuracy class: GG1 Inspection required: yes Special features Material: steel Finishing: high edges and flat sides finely ground Variant: stainless option available short-term from factory stock Design note: from 2000 mm double T-section with two hand slots Packaging unit: 1 FAQ What accuracy class does this straight edge meet? The straight edge meets the GG1 accuracy class as specified for DIN 874/I and is supplied as an inspection-required item. Is the 500 mm ruler suitable for routine workshop inspections? Yes, the 500 mm steel straight edge is designed for everyday workshop checks and aligns with practical inspection routines due to its compact length and stable cross-section. Can this straight edge be used in corrosive environments? A stainless version is noted as available short-term from factory stock, offering improved corrosion resistance where required. How is the tool finished to ensure reliable contact? The tool features finely ground high edges and flat sides that provide consistent bearing faces for repeatable measurements. Which SKU identifies this product for ordering? This item is listed under SKU 4000858822NW and is described as Lineal DIN874/I L.500mm STA H.PREISSER Manufacturer / Responsible: NORDWEST Handel AG, Robert-Schuman-Straße 17, 44263 Dortmund
500mm Steel Rule Flexible Stainless Steel Marked A mm/mm, 30x1 Section - TECWERK
Take advantage of a laser-etched mm/mm scale and a flexible stainless spring steel construction for reliable, repeatable measurements in everyday workshop and inspection tasks. Order the rule directly via Metav Werkzeuge or contact our consultants for application advice. Steel rule L 500 mm — flexible stainless spring steel, mm/mm scale (TECWERK) The Steel rule L 500 mm is a flexible stainless measuring rule optimised for clear metric readings and practical use in workshop metrology and quality control. 500 mm measuring length Laser-etched mm/mm scale Flexible stainless spring steel Cross-section 30 x 1 mm Durable graduations for consistent, traceable readings The rule features a laser-etched scale, which produces permanently marked graduations that resist wear and preserve legibility over time. The mm/mm metric division provides straightforward readings in millimetres for routine tasks and documentation. Permanent marking reduces the need for repeat verification after heavy use, supporting precision in series measurements and lowering the risk of misreading. This makes the rule suited to both production benches and inspection stations where repeatable results are essential. Flexible form for measuring on curved or confined workpieces Constructed from stainless spring steel, the measuring strip bends without kinking and returns to its original shape, allowing measurements on curved surfaces and across edges. The flexible design combined with a 30 x 1 mm cross-section balances tactile stability with adaptability, so the instrument lies flat against surfaces while remaining easy to position. The corrosion-resistant material ensures longevity in a busy workshop environment and simplifies storage after use. Conformity and quality assurance built into the tool The construction is marked as inspection required, reflecting a suitability for regulated measuring tasks where documentation and traceability matter. The compact 500 mm length provides a practical working range for many standard components, while the robust spring steel body and laser-etched graduations support routine calibration and audit processes. For users seeking dependable results, this measuring rule supplies the necessary durability and readability to integrate into quality workflows. Contact Metav Werkzeuge for tailored application advice and to confirm suitability of this TECWERK steel rule for specific measuring tasks — email info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: 4000858772NW Product type: Steel rule Label: Stahlmaßstab L.500mm rostfr.Stahl biegsam Teilung A=mm/mm H.PREISSER Facts Length: 500 mm Cross-section: 30 x 1 mm Division: mm/mm Packing unit: 1 Inspection required: yes Special features Laser-etched scale Flexible design Material: stainless spring strip steel Application: workshop measurement and inspection FAQ How durable are the graduations on this steel rule? The graduations on the TECWERK steel rule are laser-etched, producing permanent markings that resist abrasion and remain legible for extended service life. Is this measuring rule suitable for curved surfaces? Yes, the rule’s flexible stainless spring steel construction allows measurements on curved and irregular workpieces while maintaining stability. Does the rule require inspection or calibration before use? This item is marked as inspection required, so it is appropriate to include the rule in documented quality checks or to have it verified as part of a quality assurance process. What are the exact dimensions and profile of the measuring strip? The instrument measures 500 mm in length with a 30 x 1 mm cross-section, providing a slim but stable profile for workshop tasks. Can this rule be used in environments prone to corrosion? The material is stainless spring steel, offering enhanced corrosion resistance compared with plain carbon rules, making it suitable for many workshop environments. Manufacturer/Responsible: NORDWEST Handel AG, Robert-Schuman-Straße 17, 44263 Dortmund
500mm Steel Scale Flexible Stainless Steel 30x1 1/2mm Division - TECWERK
Combine durable stainless spring steel, a laser-etched permanent scale and a flexible design for reliable, repeatable measurements in everyday workshop use; order this item directly via Metav Werkzeuge or consult our advisers for specification support. TECWERK Flexible Stainless Steel Rule L 500 mm — Laser-etched scale, mm / 1/2 mm division A TECWERK flexible stainless steel rule L 500 mm for precise linear measurement tasks in workshops, inspection benches and fitting operations. Laser-etched scale for long-term legibility Flexible spring steel construction Precise mm / 1/2 mm graduation 500 mm length with 30 x 1 mm cross-section Consistent measurement accuracy for everyday tasks The laser-etched graduation provides a clear, abrasion-resistant reading that preserves scale contrast over prolonged use. With a mm / 1/2 mm division, the rule supports common metrology and layout work where half-millimetre graduations improve placement and alignment. The permanent marking reduces requalification frequency and ensures that measurements remain traceable and easy to verify during routine checks. Bendable design for work on curved or confined parts Built from stainless spring steel and finished as a flexible rule, this instrument bends to follow curved surfaces while returning to its original shape. The slim 30 x 1 mm cross-section combines low profile with sufficient rigidity for steady alignment on pipes, tubing and sheet edges. The construction therefore supports both flat layout duties and profiling tasks without adding bulk to the tool kit. Built for workshop compliance and durability Marked as inspection required, the rule is intended for use where periodic verification is part of quality procedures. The stainless material offers corrosion resistance, contributing to a longer service life and reliable readings in mixed workshop environments. The 500 mm length gives a practical reach for routine layout and rough checking, while the flexible form factor reduces damage risk when handled or stored in tool rolls. Choose the TECWERK flexible stainless steel rule for dependable, long-lasting shop measurements — contact Metav Werkzeuge for supply and expert advice at info@metav-werkzeuge.com or +49 2822 7131930 Technical data Article number: 4000858774NW Label: Flexible stainless steel rule, laser-etched scale, mm / 1/2 mm division Manufacturer: TECWERK Key dimensions Length: 500 mm Cross section: 30 x 1 mm Graduation: mm / 1/2 mm Packaging unit: 1 Features Laser-etched scale Flexible design (bendable) Material: stainless spring steel Inspection required FAQ Is the scale marking durable against wear? The laser-etched scale on the TECWERK flexible stainless steel rule is designed for long-term legibility and resists abrasion better than painted or printed markings. Can the rule be used on curved surfaces? Yes, the bendable construction made from stainless spring steel allows the rule to follow curved profiles while maintaining a consistent reading. What graduations are available on this rule? This steel rule offers mm / 1/2 mm graduations, providing half-millimetre resolution for finer layout and alignment tasks. Is the rule suitable for a workshop environment with occasional moisture? Constructed from stainless spring steel, the rule is corrosion-resistant and suitable for typical workshop conditions; regular inspections are recommended as stated by the product's inspection requirement. How long is the rule and what is its profile? The rule measures 500 mm in length and has a 30 x 1 mm cross-section, balancing reach with a slim profile for versatile workshop use. Manufacturer / Responsible: NORDWEST Handel AG, Robert-Schuman-Straße 17, 44263 Dortmund
500mm Steel Scale Flexible With Ground Edge, Metric Division A=mm/mm - TECWERK
Combine durable stainless steel construction, a clear mm/mm printed graduation and a flexible 500 mm length for reliable, repeatable workshop measurements — order the steel rule directly via Metav Werkzeuge or ask our consultants if needed. Steel rule 500 mm (stainless, flexible) – TECWERK precision measuring scale The Steel rule 500 mm (stainless, flexible) is a precision measuring scale for workshop and inspection use, offering a printed mm/mm graduation and a ground measuring edge for consistent readings. Precision execution, printed mm/mm scale Flexible, fits flat and curved surfaces Ground measuring edge for accurate readings Wide 30 mm design with matte finish Consistent accuracy for routine checks The rule is manufactured in a precision execution that combines a printed mm/mm graduation with a ground measuring edge, delivering reproducible readings across repeated checks. The rigid but flexible construction keeps the measuring edge true while allowing use on slightly curved surfaces; this reduces repositioning time and minimises cumulative error during serial measurements. The clear graduation and matte surface lower glare and improve legibility under workshop lighting, supporting faster verification without specialised equipment. Built for robust workshop environments Constructed from stainless steel, the scale resists corrosion and stands up to regular handling in industrial settings. The 30 x 0.5 mm cross-section and the wide 30 mm format provide stability on workpieces, while the flexible characteristic permits measuring on cylinders and contoured parts where a fully rigid rule would be unsuitable. As a checked measurement tool, it meets typical traceability needs for production control and incoming inspection, giving operators confidence in dimensional assessments during everyday tasks. Practical handling that saves time The printed scale and sharp graduation image reduce interpretation errors and speed up measurement routines, making the tool suitable for workshop staff and inspection benches alike. The flexible design enables quick alignment on uneven surfaces and the ground edge supports reliable zeroing against reference faces. If additional assurance is required about suitability for a specific application, the Emmerich team can provide further technical details and advice — a practical safety net for buyers seeking precise, dependable measuring tools. Contact Metav Werkzeuge today to discuss how this TECWERK steel rule fits into existing inspection procedures or to request tailored guidance from our consultants — info@metav-werkzeuge.com / +49 2822 7131930 Technical data Article number: 2000858735NW Brand: TECWERK Product type: Steel rule Length: 500 mm Cross-section: 30 x 0.5 mm Width: 30 mm Material: stainless steel Graduation: printed mm/mm Execution: flexible Measuring edge: ground Surface: matte for improved readability Checked / inspection required: yes Packaging unit: 1 FAQ How precise is the measurement reading on this steel rule? The steel rule provides a clear printed mm/mm graduation and a ground measuring edge, designed for precise workshop measurements; the item is supplied in a precision execution suitable for standard inspection tasks (SKU 2000858735NW). Can the rule be used on curved or cylindrical surfaces? Yes, the flexible design allows the rule to conform to gentle curves and cylinders, enabling direct measurement on such shapes without compromising the ground edge reference. What is the material and surface treatment of the rule? The instrument is made from stainless steel with a matte surface finish and a ground measuring edge to reduce glare and improve the sharpness of the graduations. Is the rule suitable for inspection benches and traceable checks? The rule is produced in a precision execution and marked as checked/inspection required, making it appropriate for routine inspection and production control where traceable, repeatable measurements are needed. How should the steel rule be maintained to preserve accuracy? Wipe the rule clean after use, avoid prolonged exposure to corrosive substances, store flat or hung to prevent permanent bending, and perform regular checks against a reference gauge to ensure continued accuracy. Manufacturer/Responsible: NORDWEST Handel AG, Robert-Schuman-Straße 17, 44263 Dortmund
500mm Steel Scale ISOFLEX Flexible Spring Steel With Polyamide Coating, 1mm Graduations - Bayerische Maß-Industrie Arno Keller GmbH
Take advantage of the combination of flexible spring-steel construction, polyamide protective coating and precise 1 mm graduations for dependable workshop measurement; order directly via Metav Werkzeuge or consult our specialists for specification support. ISOFLEX steel scale L 500 mm — flexible spring-steel rule with polyamide protection ISOFLEX steel scale L 500 mm is a flexible spring-steel measuring rule with a polyamide protective coating, designed for precise linear measurement in workshops, production and inspection tasks. Flexible spring-steel construction Polyamide protective coating 1 mm clear graduations 500 mm length, thin cross-section Accurate readings on flat and curved surfaces for faster workflows The flexible spring steel construction allows secure contact against slightly curved or irregular surfaces while preserving a straight reference when laid flat. The 1 mm graduations are printed for immediate visual clarity, so measurements are taken faster and with fewer re-checks. The slim 13 x 0.3 mm cross-section provides a defined measuring edge that aids repeatable placement, reducing operator adjustment time and improving throughput in repetitive tasks. Traceable quality and inspection-ready design for quality assurance With a durable build and a specification indicating inspection required, this measuring rule is suitable for applications where traceability and documented quality control matter. The 500 mm length covers a wide range of typical workshop measurements without frequent repositioning, and the robust construction supports routine inspection procedures. The inspection requirement signals that the item is maintained to a verifiable standard, which assists in audit situations and internal quality checks. Longer service life through protective coating and practical handling A polyamide protective coating provides high wear resistance and keeps the scale legible despite regular use, helping to avoid costly replacements. The protective layer also reduces edge corrosion risk and softens the user contact without compromising accuracy. Supplied as a single unit, the measuring rule combines compact handling with a long service life, delivering reliable results for everyday workshop measuring tasks. Contact Metav Werkzeuge for detailed technical advice and to request ordering information for ISOFLEX steel scales — direct from Emmerich with specification support and fast processing Technical Data SKU: 8000446861NW Type: ISOFLEX Label: ISOFLEX steel scale L 500 mm STA with PA protective coating Manufacturer: Bayerische Maß‑Industrie Arno Keller GmbH Data Length: 500 mm Cross-section: 13 x 0.3 mm Graduation: 1 mm Packaging unit: 1 SKU / UID: 8000446861NW Special features Flexible spring-steel measuring rule Polyamide protective coating Excellent readability High wear protection Flexible version Inspection required FAQ What measuring resolution does the scale provide? The scale offers 1 mm graduations, giving clear, easily readable linear increments suitable for standard workshop measurement tasks. Can the rule be used on slightly curved surfaces? Yes, the flexible spring-steel construction permits reliable contact on mildly curved surfaces while preserving measurement integrity. What does "inspection required" mean for this measuring rule? The designation indicates the item is intended for use where periodic verification or calibration is expected, supporting traceability and quality assurance processes. What are the key dimensions and form factor? The rule measures 500 mm in length with a slim 13 x 0.3 mm cross-section, combining reach with a defined measuring edge. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
500mm Steel Scale Precision Division 1/2mm, Laser‑Etched Stainless Spring Steel - TECWERK
Benefit from the laser-etched, corrosion-resistant construction and the fine mm / 0.5 mm graduations for reliable workshop measurement; order directly via Metav Werkzeuge or consult our team for specification support. Steel rule L.500 mm (stainless) — laser-etched graduations by TECWERK A Steel rule L.500 mm is designed for precise linear measurement in toolrooms and inspection tasks, combining clear markings and robust, thin-profile construction for everyday workshop use Laser-etched scale for clear, durable graduations Made from stainless spring strip steel Precise 0.5 mm and 1 mm graduations Cross-section 28 x 1 mm for stable handling Built for repeatable accuracy and clear read-off The stainless spring strip construction delivers a slim, stable profile that resists bending while remaining easy to position on workpieces. The laser-etched markings are produced to resist wear and remain legible after repeated use, which reduces measurement uncertainty during layout, inspection or simple workshop checks. With a length of 500 mm and a compact 28 x 1 mm cross-section, the rule fits typical benches or jigs and supports consistent readings on flat surfaces. The combination of a corrosion-resistant substrate and deep engraving enhances longevity and maintains performance where wet or oily conditions occur. Fine graduations for precise layout and verification Graduations presented in full millimetres with clear half-millimetre subdivisions provide a practical balance between speed and precision for routine metrology tasks. The deep, precise engraving ensures that marks remain visible under reflected light and after cleaning, so measurements are easier to reproduce and document. This level of detail supports quality workflows by reducing rework and improving setup times in both production and maintenance environments. Notably, the tool is identified as inspection required, indicating that it is suitable for use where regular verification and traceable checks are part of the quality process. Practical handling, maintenance and workshop benefits The thin steel section permits close contact with component edges while the spring-steel resilience minimises deformation during normal handling. The rule’s stainless spring strip steel construction offers corrosion resistance that lowers maintenance needs and extends service life. For workshops seeking reliable, straightforward measuring tools, this rule provides a cost-effective means to standardise basic linear checks and layout operations. Compatible with routine inspection equipment and easy to store in drawers or tool boards, it contributes to an organised metrology bench and steady production quality. Prefer workshop-grade precision and long-term dependability? Contact Metav Werkzeuge for tailored advice on the TECWERK steel rule L.500 mm and efficient supply from Emmerich — email info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: 2000858800NW Label: Stahlmaßstab L.500mm rostfr.STA Teilung B=mm/1/2mm TECWERK Product type: Steel rule Facts Length: 500 mm Cross-section: 28 x 1 mm Graduation: mm / 0.5 mm Packaging unit: 1 Special features Scale laser-etched Material: stainless spring strip steel Precise and deep graduations Inspection required FAQ What materials is this steel rule suitable for measuring against? The steel rule L.500 mm by TECWERK is a general-purpose linear measuring tool; it is suitable for layout and comparison checks on metal, wood and plastic surfaces where a rigid, straight reference is required. How fine are the graduations and how are they marked? Graduations on the TECWERK steel rule are in full millimetres with half-millimetre subdivisions; the markings are laser-etched to ensure long-term legibility. Is the rule corrosion resistant and suitable for workshop environments? Yes. The instrument is made from stainless spring strip steel, offering enhanced corrosion resistance for typical workshop and maintenance conditions. Does the product require calibration or inspection? The product is marked as inspection required, so periodic verification is recommended where traceable measurements are part of quality procedures. What are the dimensions for handling and storage considerations? The rule is 500 mm in length with a 28 x 1 mm cross-section, giving a slim profile that fits tool drawers, bench jigs and common workshop storage systems. Manufacturer/Responsible: NORDWEST Handel AG, Robert-Schuman-Straße 17, 44263 Dortmund
500mm Workshop Ruler Straightness 0.2–0.3mm Bevelled Edges Fine Polished, 40x5mm - TECWERK
Combining a 500 mm measuring length with a 40 x 5 mm rigid profile and a verified straightness of 0.2–0.3 mm, this TECWERK workshop straightedge provides a dependable reference for layout and inspection tasks; order directly via Metav Werkzeuge or consult their technical advisors for further clarification. TECWERK Workshop Straightedge L500 mm — 500 mm steel straightedge, straightness 0.2–0.3 mm TECWERK Workshop Straightedge L500 mm is a precision reference tool for machine shops and inspection benches, designed for layout work, flatness checks and basic inspection routines. 500 mm measuring length 40 x 5 mm rigid cross-section Chamfered and finely polished finish Straightness 0.2–0.3 mm, inspection required Accurate reference for layout and inspection The straightedge offers a dependable 500 mm datum with certified straightness 0.2–0.3 mm, ensuring consistent repeatability when establishing references on components. In practice, the declared straightness indicates the maximum deviation along the working edge; this value is essential for gauging tolerances during set-up and for comparative checks against a surface plate. The tool requires inspection, so traceability and conformity checks are facilitated where documentation of measuring equipment is mandatory. Robust profile and refined surface for everyday workshop use A sturdy 40 x 5 mm cross-section gives the instrument sufficient stiffness for handling and prevents sagging across its length, while the chamfered edge and finely polished faces reduce the risk of marking delicate parts. The high edges are ground to maintain a crisp line of sight and a consistent contact geometry, which assists in rapid visual alignment and in producing reliable scribe lines. The combination of structural rigidity and surface finish makes the straightedge suitable for repetitive workshop routines without compromising the reference quality. Built for integration into inspection routines Designed as a practical steel straightedge, the instrument is intended for routine layout tasks, flatness comparisons and basic inspection uses on the shop floor. Its measured characteristics simplify the selection process for quality control roles that require a compact, robust reference tool. Documentation and compliance are supported by the product data and SKU, so the straightedge can be recorded in tool inventories and inspection schedules as part of a structured metrology workflow. For a precise and reliable workshop reference, choose the TECWERK 500 mm straightedge and contact Metav Werkzeuge in Emmerich for ordering or technical guidance via info@metav-werkzeuge.com or +49 2822 7131930 Technical data Article number / SKU: 2000858740NW Label: Werkstattlineal L.500mm STA Geradheit 0,2-0,3mm TECWERK Product type: Werkstattlineal Numbers / core technical data Length: 500 mm Cross-section: 40 x 5 mm Straightness: 0.2–0.3 mm Packaging unit: 1 Designs / special features Chamfered edge High edges ground Finely polished surface Inspection required FAQ What level of straightness can be expected from this straightedge? The straightedge delivers a declared straightness of 0.2–0.3 mm, which is documented for the TECWERK workshop straightedge (SKU 2000858740NW) and suitable for general layout and inspection tasks. Is the tool suitable for precision layout on small components? Yes, the rigid 40 x 5 mm profile and polished working edge make the straightedge appropriate for layout and marking on smaller parts where a compact, stable reference is needed. Does the straightedge require formal inspection or calibration? The product is marked as requiring inspection; this means the instrument should be checked and recorded in accordance with the facility’s inspection regimen to maintain traceability. Can the straightedge be used directly on a surface plate for comparative checks? The straightedge was designed for comparative checks and layout work; its polished edge and ground high edges provide a reliable contact for visual and tactile comparison against a surface plate. Manufacturer/Responsible: NORDWEST Handel AG, Robert-Schuman-Straße 17, 44263 Dortmund
500x300 mm Centre Square Matt Chrome Finish, Reading In Millimetres - Metav IndustryLine
Take advantage of a robust, low-reflection layout tool with large, flat faces and corrosion-protected construction for consistent centring and marking of sizeable components; order the item directly via Metav Werkzeuge or consult their technical advisers for application guidance. Centring Square 500 x 300 mm — matt chrome-plated tool steel (Metav IndustryLine) The Centring Square 500 x 300 mm is a precision scribing and alignment tool for workshop and machine-shop layout tasks, designed to provide stable, anti-glare faces for accurate marking and centring of shafts and assemblies. Matt chrome finish reduces glare Tool steel, corrosion-protected Large 500 x 300 mm faces for big components Repeatable accuracy for layout and centring The matt chrome faces and flat profile deliver repeatable accuracy when establishing centre lines or squareness on substantial parts. With 500 x 300 mm faces the gauge offers a generous reference surface that reduces the need for repositioning, so marking operations become faster and less error-prone. The anti-glare finish improves visibility of scribed lines and etched graduations, which supports precise layout work even under strong workshop lighting. Built to last with low maintenance needs Constructed from tool steel with corrosion protection, the unit resists routine workshop wear and provides long service life with minimal upkeep. The matt finish both protects the reading surface and reduces reflective interference, meaning less time spent adjusting views or reworking marks. Robust materials and straightforward surfaces make cleaning and light maintenance easy, ensuring stable performance in regular production environments. Practical design for efficient workshop workflow At approximately 1.2 kg, the gauge balances solidity and manoeuvrability: heavy enough to sit flat on a workpiece, yet light enough for single-person handling and quick repositioning. The large faces accommodate layout on shafts and housings, and the specification indicating suitability for a shaft Ø520 mm supports use on sizeable rotating parts. Clear, machine-readable features aid rapid inspection steps and reduce cycle time in marking and set-up processes. Metav IndustryLine reliability and application scope The Metav IndustryLine version combines shop-grade durability with a finish tailored to precision marking tasks. Ideal uses include centring and scribing on shafts, flanges and housings in metalworking, toolroom layout, and general machine-shop preparation. The construction minimises distortion during handling and the broad contact faces improve alignment against straight edges and fixtures — advantages that translate directly to fewer reworks and improved scheduling reliability. For dependable workshop alignment, request the Metav IndustryLine centring square (SKU M214.176) from Metav Werkzeuge in Emmerich; technical advisers are available to advise on specific applications and integration into existing workflows Technical data Article number: M214.176 GTIN: 4054469107042 Customs tariff number: 90172039 Facts Dimensions: 500 x 300 mm Weight: 1.2 kg Special features Material: Tool steel, rust-protected Finish: Matt chrome-plated, anti-glare reading Suitability: For centring and layout on large components Compatibility: Suitable for shaft Ø520 mm Category: Scribing/marking tool (Anreisszeuge) FAQ What is the primary purpose of this centring square? The centring square is intended for accurate layout and centring of shafts, flanges and large components; the Metav IndustryLine unit (SKU M214.176) provides broad, low-reflection faces for precise marking. Is the surface finish suitable for clear scribing and reading? Yes, the matt chrome finish reduces glare and improves visibility of scribed lines and graduations, supporting consistent marking in machine-shop lighting conditions. What materials and machining environments is this tool made for? Manufactured from tool steel with corrosion protection, the gauge is built for standard workshop and industrial environments where durable, stable reference faces are required. Can this tool be used on round workpieces such as shafts? Yes; the specification lists suitability for shaft Ø520 mm, making it applicable to centring and alignment tasks on medium to large diameters. How should the centring square be maintained to ensure long-term accuracy? Regularly clean the faces of swarf and coolant, protect the surfaces from corrosive residues, and store the tool in a dry place; the robust finish reduces maintenance frequency. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
600mm Aluminium Rule With Handle Recess, 50 x 5mm Section, Millimetre Scale - TECWERK
The combination of a rigid aluminium profile, a laser-etched mm scale and an ergonomic grip recess ensures precise, repeatable marking and safe handling in daily workshop use; order the ruler directly via Metav Werkzeuge or request technical advice from the Metav team. Ruler L.600mm Aluminium with Grip Recess Q.50x5mm TECWERK — 600 mm aluminium straightedge, laser-etched mm scale The Ruler L.600mm Aluminium with Grip Recess Q.50x5mm TECWERK is a 600 mm straightedge designed for precise marking and measuring in general workshop and industrial applications, combining a stable cross-section with an easy-to-grip profile. Laser-etched mm scale for lasting legibility Solid aluminium profile 50 x 5 mm cross-section Silver anodised finish for corrosion resistance Integrated grip recess for secure handling Reliable rigidity for accurate layout work A solid aluminium profile with a 50 x 5 mm cross-section provides the straightness and stability required for repeatable marking and measurement tasks. The substantial section reduces flex when held against a workpiece, which translates into consistent accuracy when scribing lines or checking dimensions. The construction suits both light metalworking and general carpentry where a robust, lightweight measuring rule is needed; material properties ensure the tool stays dimensionally stable under normal workshop conditions. Long-lasting, precise scale for production use The laser-etched mm scale offers superior durability compared with printed graduations: the markings are resistant to abrasion, solvents and oil, so legibility remains intact through heavy use. A laser-etched mm scale also improves read-off accuracy because the engraving provides a defined contrast under workshop lighting. For those less familiar with production terminology: laser etching removes a fine layer of material to create permanent marks, avoiding the gradual wear associated with surface printing. Tough surface and comfortable handling for everyday tasks The ruler’s silver anodised surface increases corrosion resistance and reduces surface wear while maintaining a smooth, low-friction finish that is kinder to hands and workpieces. The integrated grip recess (finger recess) is shaped for secure handling, enabling steady alignment and reduced slippage during marking or measurement. This ergonomic detail supports safe one-handed use and helps to keep the straightedge firmly in place when transferring measurements—an important advantage in fast-paced or repetitive workflows. Fits neatly into workshop routines and supply chains As a compact and durable straightedge, the rule integrates easily into workshop tool sets, jigs and layout stations; storage and maintenance are straightforward thanks to the anodised surface and the robust profile. The item is suitable for trades that demand quick, accurate measurements—carpentry, metalworking, pattern making and general assembly. Metav’s supply approach ensures consistent availability and clear specification data from Emmerich, supporting uninterrupted production and reliable procurement decisions. For workshop procurement or technical clarification about the TECWERK ruler (SKU 2000858737NW), contact Metav Werkzeuge for order placement or individual advice; Metav Werkzeuge is available at info@metav-werkzeuge.com or +49 2822 7131930 Technical data Article number: 2000858737NW Label: Lineal L.600mm Alu.m.Griffmulde Q.50x5mm TECWERK Product type: Ruler Manufacturer: TECWERK Facts Length: 600 mm Cross-section: 50 x 5 mm Packaging unit: 1 Special features Material: Aluminium Scale: laser-etched mm scale Finish: silver anodised Design: with grip recess FAQ Is the scale on the ruler durable for industrial use? The laser-etched mm scale on the TECWERK ruler (SKU 2000858737NW) is designed for long-term legibility in industrial and workshop environments and resists wear better than printed graduations. Can the straightedge be used for scribing and layout on metal? Yes, the aluminium ruler with its rigid 50 x 5 mm profile is suitable for layout and scribing tasks on metal and wood where a stable straightedge is required. Does the ruler have any protective surface treatment? The measuring rule features a silver anodised finish that increases surface hardness and resistance to corrosion. Is handling improved compared with standard flat rulers? The integrated grip recess provides a secure hold and reduces slippage, making the straightedge easier to use for one-handed marking and transferring measurements. Where can the TECWERK ruler be ordered or inspected in detail? Detailed enquiries and orders for the TECWERK ruler (Ruler L.600mm Aluminium with Grip Recess Q.50x5mm, SKU 2000858737NW) can be placed through Metav Werkzeuge, which supplies technical information and procurement support. Manufacturer/Responsible: NORDWEST Handel AG, Robert-Schuman-Straße 17, 44263 Dortmund
Precision marking that speeds up workshop tasks
Marking tools are the foundation of accurate fabrication and repeatable setup in industrial workshops. From scribing parallel lines on metal to laying out joinery on timber, the right marking tools ensure cuts, drills and mill passes start from a clear, reliable reference.
How these tools perform on the shop floor
A typical set of marking tools includes the scriber, the scriber needle, the precision caliper and the marking gauge. Each instrument serves a defined purpose: the scriber and scriber needle create fine guide lines for drilling and milling; the precision caliper measures and transfers exact distances for internal and external features; the marking gauge produces parallel lines on wood and other sheet materials. Used correctly, these instruments reduce rework by turning layout into a measurable, repeatable process.
Practical benefits that matter in production
- Improved accuracy for millimetre work, enabling tighter tolerances and more first-pass success.
- Reduced setup time through repeatable marking and rapid transfer of dimensions.
- Versatility across materials — suitable for wood, metal and plastics.
- Ease of use: simple handling of the scriber needle and intuitive adjustment on the precision caliper speeds routine tasks.
- Better quality control: clear, durable scribed lines act as unambiguous guides during cutting, drilling and finishing.
Why Metav is the sensible sourcing partner
Metav stands for democratising precision. As a precision partner with decades of experience, Metav supplies workshop-grade marking tools from its Emmerich-based quality hub, combining a wide range with consistent quality control. With more than 48,000 customers and a portfolio exceeding 250,000 products, Metav offers reliable availability and expert advice, making it a practical choice for procurement managers and workshop professionals seeking a single dependable supplier.
Summary
Well-chosen marking tools — including the scriber, scriber needle, precision caliper and marking gauge — turn layout into a fast, accurate and repeatable step in every production process, raising throughput and reducing scrap.
FAQ
What is the difference between a scriber and a scriber needle?
A scriber produces continuous guide lines for edges and profiles, while a scriber needle creates single, fine marks or narrow lines that serve as precise reference points for drilling or aligning operations.
When should I use a precision caliper for marking?
Use a precision caliper whenever millimetre-accurate distances must be transferred directly to the workpiece, for both internal and external features; it is particularly useful in machine shops and metalworking where exact offsets are required.
Are marking gauges suitable for metalwork as well as woodworking?
A marking gauge is primarily designed for wood, where its sharp fence and beam produce clear parallel lines; for metal, the scriber and scriber needle are generally preferred because they provide the finer, more durable scribed lines needed for machining.
How do marking tools improve production efficiency?
By providing clear, repeatable layout references, marking tools reduce measurement errors and setup iterations, which shortens cycle times and increases first-pass yield on parts.
Fragen zu diesen Produkten??
Mit mehr als 30 Jahren Erfahrung beraten wir Sie gerne persönlich.
Tel.: +49 2822 7131930
Mail: info@metav-werkzeuge.com