500mm Depth Caliper With Interchangeable Probes, Digital Readout Mm/Inch, ABS, ISO 17025 Calibration, Plastic Case - Filetta

Take advantage of a compact, low‑profile attachment that adds a precise measuring surface and flexible positioning to special calipers; the combination of a 15 mm height, measuring faces 300 x 6 mm and an attachable, movable design streamlines inspection tasks in confined or awkward geometries. Order via Metav Werkzeuge or consult their specialists for application advice. Measuring bridge – attachable, movable accessory for special calipers by Filetta The measuring bridge is an attachable and movable accessory designed to extend the measuring capabilities of specialty calipers for workshop inspection, fixture setup and quality checks. Attachable and movable design Measuring faces 300 x 6 mm Compact 15 mm height profile Extend reach and capability without new instruments A compact measuring bridge adds a stable, repeatable contact surface to existing special calipers, allowing the measurement of recessed or wider features without changing the baseline instrument. The measuring faces (300 x 6 mm) provide a long, narrow contact suited to slot and step measurements, while the low 15 mm height keeps the assembly slim and easy to position. This extension reduces the need for multiple instruments and speeds up inspection workflows by enabling more measurements to be taken with a single calibrated tool. Precision where space is limited Engineered for practical precision, the accessory transfers the caliper’s reference plane to areas that are otherwise hard to access. A slim profile and narrow faces help to minimise tilt and measurement error when working in confined spaces; the design prioritises stiffness over length to preserve reproducibility. The result is consistent dimensional data that supports precise set‑ups and reliable quality control, making the bridge a pragmatic choice for machine shops and tooling departments that require accurate results without complex fixtures. Simple handling and workshop integration The bridge is designed for easy mounting and fine repositioning on the host caliper, so adjustments can be made quickly during iterative checks or tool set‑up. Its movable configuration supports flexible measuring scenarios, from step and depth checks to distance transfers between features. As an accessory compatible with special calipers, it widens the practical use of existing measuring equipment and keeps the test procedure straightforward — a time‑saving asset for routine inspection cycles. For application guidance or to order the Filetta measuring bridge, contact Metav Werkzeuge in Emmerich: info@metav-werkzeuge.com or +49 2822 7131930 — specialists will advise on fit and delivery Technical data Article number: MS910.499 Manufacturer: Filetta Facts Height: 15 mm Measuring faces: 300 x 6 mm Special features Attachable to special calipers Movable/adjustable positioning Slim, low‑profile contact surface FAQ What is the primary use of this measuring bridge? The measuring bridge is intended as an attachable accessory for specialty calipers to measure recessed features, steps and long narrow surfaces where direct caliper jaws cannot reach. Is the bridge compatible with standard calipers or only special models? Compatibility depends on the caliper geometry; the bridge is designed for use with special calipers and similar workshop measuring tools and may require a matching mounting interface. Does the measuring bridge change the measurement reference of the caliper? Yes, when fitted the bridge establishes a new contact plane via its faces (300 x 6 mm) so measurements reflect the transferred reference; users should account for any offset in documentation. Manufacturer / Responsible: Schut Geometrische Meettechniek bv; Duinkerkenstraat 21; 9723 BN Groningen; The Netherlands; +31 50 5877877; schutnl@schut.com

The combination of a compact 15 mm profile, 500×6 mm measuring faces and an attachable, adjustable mounting delivers reliable medium‑range measuring capacity for workshop and fixture tasks; order the measuring bridge directly via Metav Werkzeuge or ask our consultants if needed. Measuring bridge MS910.500 – attachable, adjustable bridge with 500×6 mm faces (Filetta) A Measuring bridge MS910.500 designed as an attachable and sliding accessory for special calipers, intended to extend reach and improve repeatable positioning in medium‑format component inspection. Attachable and adjustable design Measuring faces 500×6 mm 15 mm low-profile beam Precise medium-range measuring for workshop and toolroom tasks The design targets the mid‑range measuring class, combining a low‑profile 15 mm beam with 500×6 mm measuring faces to bridge the gap between compact gauges and large‑scale instruments. Classified for medium‑range applications, this accessory is suited to fixtures, mould components and larger workpieces where reach and rigidity must be balanced. The measured geometry of the faces ensures consistent contact geometry and supports repeatable readings when paired with compatible calipers. Flexible mounting that reduces setup time and increases throughput An attachable and slideable configuration provides flexible positioning on the carrier caliper, enabling quick alignment without altering the base instrument. The sliding mount improves workflow by allowing fast repositioning along the 500 mm face length, which shortens setup cycles and reduces non‑productive time in repetitive measurement tasks. Built for stability, the accessory supports reliable contact during inside, outside and step checks when used within its intended range. Workshop-ready design backed by Metav’s supply and advice Offered as a practical extension for special calipers, the bridge is prepared for everyday industrial use and integrates smoothly into existing measurement stations. The component is identified by the MS910.500 code and the Filetta brand, providing a clear sourcing route. For buyers seeking confidence in delivery and application, Metav Werkzeuge combines broad product availability with technical guidance to support specification and installation decisions. For application advice or to procure the Filetta MS910.500 measuring bridge with its 500×6 mm faces, contact Metav Werkzeuge in Emmerich for tailored assistance and ordering support. Technical Data Article number: MS910.500 Manufacturer: Filetta Designation: Measuring bridge Facts Measuring faces: 500×6 mm Height: 15 mm Special features Attachable and adjustable mounting Category: Special measuring calipers FAQ What measurement range does the bridge cover and how is it classified? The bridge provides a 500 mm measuring face length and is classified in the medium‑range category, suited to larger fixture and mould components where a balance of reach and stiffness is required. Which calipers are compatible with this bridge? Compatibility depends on the caliper carrier geometry; the MS910.500 is designed as an attachable accessory for special calipers and mounts where a slide‑on connection and retention are provided. Does the bridge support inside, outside and step measurements? When used with an appropriate carrier caliper, the accessory supports the typical range of caliper functions, including inside, outside and step/shoulder measurements within its intended application range. Is the measuring bridge suitable for production repeatability tasks? Yes; the stable beam profile and defined measuring faces aid repeatable contact geometry, making the accessory suitable for production checks and routine inspection where mid‑range repeatability is required. Manufacturer / Responsible: Schut Geometrische Meettechniek bv; Duinkerkenstraat 21; 9723 BN Groningen; The Netherlands; +31 50 5877877; schutnl@schut.com