Gibt es einen Hahn und Kolb Online Shop?

Take advantage of a compact, ISO‑aligned clamping solution that combines precise insert compatibility with straightforward maintenance; the SER 1010 format and 10 x 10 mm clamping head enable reproducible right‑hand threading while Metav Werkzeuge provides reliable procurement and technical guidance. Clamping Holder SER 1010 (D495TM) – 10 x 10 mm head, right‑hand thread by Teknik Makina The Clamping Holder SER 1010 is a toolholder for turning applications designed for outside right‑hand threads, suitable for standard 11 ER indexable inserts and small‑profile toolposts. Compact 10 x 10 mm clamping head Compatible with 11 ER indexable inserts Right‑hand thread orientation Lightweight at 0.091 kg for low overhang Consistent thread quality through defined geometry The compact SER 1010 format provides a clearly defined clamping face and controlled cutting height, which together deliver reproducible threading on outside right‑hand threads. The specified 20 mm cutting height and the dedicated insert pocket for 11 ER plates reduce axial variation during turning, resulting in fewer scrap parts and less rework. For workshops aiming for measurable process stability, the holder’s nominal dimensions support predictable tool offsets and simpler cycle programming. Faster set‑ups and predictable maintenance intervals A small footprint of 10 x 10 mm for the clamping head and an overall length of 100 mm simplify integration into compact toolposts and reduce interference with adjacent tooling. Fast mechanical access is enabled by the Torx T8 key and M2.5 x 5.5 torx screw, allowing controlled clamping torque and quicker insert changes. The modest mass of 0.091 kg lowers centrifugal loads and can improve balance on long overhangs, decreasing vibration and extending insert life—advantages that translate directly into reduced machine downtime. Broad compatibility for routine turning tasks The holder is specified for use with H11‑ER11 boring bars and standard 11 ER indexable inserts, ensuring cross‑compatibility with common turning tool inventories. Its right‑hand cutting orientation is optimised for conventional outside threading operations. The ISO designation SER 1010 clarifies the holder’s interface dimensions for machining planners and procurement, so replacement and system matching are straightforward and verifiable against tool lists and CAM setups. For specification checks or to request a tailored quotation for Teknik Makina’s clamping holder, contact Metav Werkzeuge at info@metav-werkzeuge.com or call +49 2822 7131930 Technical Data SKU: D495TM Manufacturer: Teknik Makina Designation: Clamping holder for outside right‑hand thread ISO designation: SER 1010 Core specifications Overall length: 100 mm Clamping head: 10 x 10 mm Cutting height: 20 mm Weight: 0.091 kg Cutting direction: right Compatible insert: 11 ER Torx key: T8 Torx screw: M2.5 x 5.5 Special features Compatible with H11‑ER11 boring bar Built for outside right‑hand threading Designed for standard 11 ER indexable inserts FAQ Which insert format fits this holder? The clamping holder accepts 11 ER indexable inserts, which are industry‑standard profiles for turning and threading operations and fit the SER 1010 pocket. Is the holder suitable for outside right‑hand threading only? Yes. The toolholder is specified for outside right‑hand threads and is configured accordingly for conventional turning on the right‑hand side. What are the key dimensions for machine set‑up? Key dimensions include a 10 x 10 mm clamping head, 20 mm cutting height and an overall length of 100 mm; these values support accurate tool offset programming for the D495TM holder. Which fastening hardware is required for insert clamping? Insert retention uses a Torx T8 key with an M2.5 x 5.5 torx screw, enabling consistent clamping torque and straightforward insert changes. Can this holder be used with common boring bars? Yes; the holder is compatible with H11‑ER11 boring bars, allowing integration into standard turning toolsets for routine workshop applications. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of a compact, ISO‑compatible clamp holder that combines precise clamping, fast insert changes and robust dimensions for consistent external threading – ideal for repetitive production. Order the clamp holder directly via Metav Werkzeuge or consult the specialists for compatibility advice. Clamp holder SER 1212 — right‑hand outside‑thread clamping, Teknik Cutting Tools The Clamp holder SER 1212 is a compact toolholder engineered for secure clamping of 11 ER indexable inserts when machining right‑hand external threads. ISO designation SER 1212 for easy integration Compact 12 mm width and 12 mm height Compatible with 11 ER indexable inserts Torx T8 screw M2.5x5.5 for repeatable clamping Precise clamping that reduces setup variation The holder is designed to deliver consistent clamping across repeated operations, which reduces part deviation and rework. With its SER 1212 ISO designation the component matches common toolpost standards, enabling straightforward replacement of older holders without recalibration of the clamping plane. The compact form and secured screw interface provide stable seat location for the insert, contributing to repeatable tool geometry and predictable machining results. Fast, reliable insert changes to minimise downtime A mechanical design centred on quick insert retention means changeovers are performed with minimal effort. The combination of a Torx T8 driver and M2.5x5.5 screw secures the insert reliably while allowing controlled torque during replacement. This reduces the risk of incorrect fastening and supports an efficient workflow when multiple insert swaps are required on short production runs. Balanced dimensions for rigidity and access With a width of 12 mm, height of 12 mm and a cutting height of 20 mm, the clamp holder provides a compact footprint while maintaining sufficient cross‑section for rigidity. The 125 mm overall length offers a practical reach for external threading operations without excessive overhang. The measured mass of 0.16 kg contributes to stable dynamic behaviour on the turret and helps keep tool balance predictable during rapid indexing. Clear compatibility with standard insert and bar interfaces The holder is specified for 11 ER indexable inserts and pairs with the K11‑ER11 clamping bar designation, ensuring compatibility with widely used insert families and bar systems. The defined right‑hand cutting direction aligns with conventional external thread turning applications, simplifying tool selection and ensuring correct cutting geometry without additional adaptation. Designed for workshop integration and efficient inventory As a standardised clamp holder, this item is intended to integrate seamlessly into existing turning stations and tool assortments. The ISO labelling and familiar connection details simplify stock management and spare‑part replacement. Sourcing through an experienced distributor like Metav Werkzeuge benefits procurement reliability and reduces the administrative overhead associated with multiple suppliers. Durable construction for dependable production routines Although detailed material and coating data are not provided here, the mechanical concept—secure screw clamping, defined seat geometry and compact dimensions—fosters long service life under typical turning conditions. The robust assembly supports repeatable tightening and maintains seating integrity across insert changes, which helps preserve tool performance and reduces the frequency of unplanned adjustments. For technical clarification or to secure supply, contact Metav Werkzeuge GmbH in Emmerich: info@metav-werkzeuge.com | +49 2822 7131930 — the team can advise on Teknik Cutting Tools clamp holder SER 1212 (SKU D497TM) and its fit for specific toolholders Technical data SKU: D497TM ISO designation: SER 1212 Manufacturer: Teknik Makina Width: 12 mm Height: 12 mm Cutting height: 20 mm Total length: 125 mm Weight: 0.16 kg Torx key: T8 Torx screw: M2.5x5.5 For indexable inserts: 11 ER Compatible toolholder: K11-ER11 Cutting direction: right-hand Suitable for outside threads Design: clamp holder for external threading FAQ What insert type does this clamp holder accept? The clamp holder accepts 11 ER indexable inserts and is designed to work with corresponding insert geometries for external threading. Is the holder suitable for right‑hand threading only? Yes, the design specifies a right‑hand cutting direction for outside threads, matching standard right‑hand turning operations. Which toolholder or bar does it pair with? Compatibility is indicated with K11‑ER11 toolbars; the ISO designation SER 1212 ensures alignment with common toolpost standards. What is the overall length and how does that affect reach? The overall length is 125 mm, providing practical reach for external thread machining while keeping overhang and vibration risk low. What is the SKU for ordering and reference? The product is listed under SKU D497TM for ordering and stock reference. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of internal coolant and a secure clamping system compatible with 16 ER indexable inserts for stable machining and reduced setup time; order the holder directly via Metav Werkzeuge or consult our specialists for integration advice. Klemmhalter AP602TM — clamp holder for ER indexable inserts with internal coolant, 16 ER, by Teknik Makina The Klemmhalter AP602TM is a compact clamp holder designed for machining applications that use ER indexable inserts, offering internal coolant delivery and a robust 20 × 20 mm shank for reliable toolholding in production environments. Internal coolant delivery system Compatible with 16 ER indexable inserts Compact 20 × 20 mm shank design Torx fixation M3.5 × 11, T15 key required Secure clamping for consistent cutting performance A precise clamping system is essential for repeatable machining results; this clamp holder locks 16 ER indexable inserts firmly in place to reduce micro-movement that can shorten tool life. The integrated internal coolant channel directs coolant towards the cutting edge, which helps to control cutting temperatures and improve chip evacuation. For workshops and small production lines, the combination of secure insert retention and coolant delivery translates into fewer insert changes and more consistent part quality, preserving surface finish and dimensional accuracy over longer runs. Workshop-ready dimensions and straightforward maintenance With a compact shank of 20 × 20 mm and an overall length of 125 mm, the holder is designed for easy mounting and clearance in multi-tool turrets and tool posts. Fixation is achieved via a Torx M3.5 × 11 screw and requires a T15 key for assembly or replacement, simplifying routine maintenance. Compatibility with locating parts is aided by the supplied references to the TA061 locating plate and TA060 shim, enabling quick retrofitting into existing setups. The unit benefits from first-class metal workmanship, giving a durable feel that sustains alignment and clamping force under repetitive loading. Smooth integration into production workflows Engineered by Teknik Makina, the holder supports stable clamping that can reduce setup times and contribute to predictable cycle times on CNC lathes and turning centres. Its specification makes it suitable for standard indexable-insert tool systems where coolant-through capability is required for longer tool life and improved process reliability. For technical clarifications or to verify compatibility with tool turrets and insert ranges, Metav Werkzeuge’s technical team can provide detailed advice and adaptation options, ensuring the holder integrates seamlessly into existing production routines. Contact Metav Werkzeuge for tailored integration advice on the Teknik Makina AP602TM clamp holder and to discuss suitability for specific machining setups; reach our Emmerich team by email or phone for precise recommendations. Technical Data Article number: AP602TM Name: Klemmhalter for ER indexable inserts with coolant Manufacturer: Teknik Makina SKU: AP602TM Compatible insert size: 16 ER Internal coolant: yes Facts Overall length: 125 mm Shank dimensions: 20 × 20 mm Torx screw: M3.5 × 11 Torx key size: T15 Special features Internal coolant delivery Compatible with locating plate TA061 Use shim TA060 for correct seating First-class metal workmanship FAQ What insert size fits this clamp holder? The clamp holder AP602TM is specified for 16 ER indexable inserts and secures the insert form for stable machining. Does the holder supply coolant to the insert? Yes, the AP602TM features an internal coolant channel to direct cutting fluid towards the insert, improving cooling and chip evacuation. Which fastening parts are required for assembly? Assembly uses a Torx M3.5 × 11 screw and a T15 key; these are the designated fixation components for the AP602TM by Teknik Makina. Can the holder be fitted to existing plates and shims? The holder is compatible with locating plate TA061 and shim TA060, facilitating retrofit into existing tool setups where those parts are used. Who manufactures the clamp holder and who supplies it? The clamp holder is manufactured by Teknik Makina (Teknik Cutting Tools) and supplied through Metav Werkzeuge for distribution and technical support. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of a standardised SER 1616 interface and compact 16 x 16 mm body to speed set-up and ensure repeatable threading results; order directly via Metav Werkzeuge or consult the team for process compatibility and delivery options. Clamping holder for external right-hand thread »SER 1616« – Teknik Cutting Tools A clamping holder engineered for right-hand external threading, compatible with 16 ER indexable inserts and designed for reliable workshop use SER 1616 standardised design Compatible with 16 ER inserts Right-hand threading orientation Compact 16 x 16 mm body Consistent centring and repeatable threading quality The SER 1616 interface and compact 16 x 16 mm profile provide a rigid, predictable mounting that reduces runout and setup variability. This standardised mounting translates into improved repeatability and fewer rejected threads in serial production. By choosing a holder with a defined cutting height and clamping geometry, machine shops benefit from shortened machine idle times and more consistent surface finishing on external threads. Fast, secure clamping for stable cutting performance The holder uses a proven clamping concept with a T15 torx engagement and an M3.5x11 fastening screw, enabling controlled clamp force and straightforward insert changes. The specified cutting height of 25 mm aligns the insert with common toolpost setups, which minimises rework and reduces vibration during threading operations. The combination of secure fixing and quick access to the insert supports efficient shift-to-shift tooling changes while maintaining process stability. Workshop-ready compatibility and easy integration With an overall length of 100 mm and a nominal mass of 0.22 kg, the unit integrates neatly into standard toolbanks and turning fixtures without excessive overhang. It is designed for 16 ER indexable threading inserts and matches H16-ER16 tool shank systems, offering broad compatibility across existing machine tool fleets. The right-hand cutting orientation suits conventional lathe threading applications. Sourcing through Metav ensures a stable supply chain and access to technical advice, supporting uninterrupted production and straightforward parts replacement. Contact Metav Werkzeuge today for technical advice or to order Teknik Cutting Tools’ SER 1616 clamping holder; email info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: D501TM Manufacturer: Teknik Cutting Tools Designation: Clamping holder for external right-hand thread (SER 1616) Dimensions & weight Body height: 16 mm Head / cutting width: 16 mm Body width: 16 mm Cutting height: 25 mm Overall length: 100 mm Weight: 0.22 kg Features & compatibility Compatible with 16 ER indexable inserts SER 1616 profile Right-hand cutting direction Torx key size T15 Fastening screw M3.5x11 U‑plate: TA061 Shim: BSP010 Toolholder designation: H16-ER16 FAQ What insert size does this holder accept? The holder is specified for 16 ER indexable threading inserts and matches the H16-ER16 tool shank designation. Is the holder suitable for left-hand threads? This model is configured for right-hand external threading and is intended for conventional clockwise cutting on lathes. Which fastening screw is required for the clamping screw? Fastening is performed with an M3.5x11 screw and torx engagement T15 for secure, repeatable clamping. Can the toolholder be used in compact tool posts? With a 16 x 16 mm body and overall length of 100 mm, the holder fits most standard compact toolposts and modular tool systems. What is the cutting height and why does it matter? The cutting height is 25 mm; correct cutting height ensures the insert sits on centre with the workpiece axis, reducing tool wear and improving thread geometry. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of secure, repeatable clamping with a compact footprint and left‑hand cutting orientation for efficient turning setups; compatible with standard 16 IR indexable inserts and featuring a 25×25 mm head for tight tool layouts. Order directly via Metav Werkzeuge or request advice from our consultants for integration into existing tool chains. Clamping holder 16 IR — left‑hand, SEL 2525 clamping tool by Teknik Makina Clamping holder 16 IR a left‑hand clamping tool for indexable 16 IR inserts, intended for compact turning and toolpost installations where secure insert retention and precise cutting height control are required Left‑hand orientation for reverse cutting For 16 IR indexable inserts Compact 25×25 mm head and shank 150 mm overall length, weight 0.753 kg Precision clamping for consistent machining results The Clamping holder 16 IR delivers precision clamping via a compact geometry that stabilises indexable inserts during cutting. With a 25 mm head width and an effective cutting height of 30 mm, the design reduces vibration and repeatable run‑out, which translates into improved surface finish and longer insert life. The result is measurable process stability—fewer tool changes and more consistent cycle times on batch production. Compact design that fits tight tool layouts The SEL 2525 format combines a 25×25 mm head and shank profile with a 150 mm overall length, enabling close‑packed toolpost arrangements and multi‑station turrets. The holder’s modest mass (0.753 kg) helps to keep centrifugal loads low on high‑speed turrets while still providing the rigidity expected in a workshop environment. Compatibility with the M16‑IR16 shank designation simplifies replacement and inventory management for standardised tool fleets. Practical handling and installation in the workshop Installation and set‑up are straightforward: the holder secures 16 IR inserts with a positive clamping action that preserves insert position during heavy cuts. The left‑hand cutting orientation is clearly marked, reducing the risk of incorrect mounting in mixed‑direction toolrooms. As the component is compact and lightweight, it supports rapid tool changeover routines and reduces downtime in production maintenance cycles. Suitable use cases and reliability in production Designed for small to medium‑batch turning operations, this clamping holder is beneficial where repeatability and compact arrangement matter most. The combination of SEL 2525 geometry and standard 16 IR compatibility supports lean tooling strategies and consistent output quality. For operations prioritising uptime and predictable machining results, the holder offers a pragmatic balance between space economy and robust insert retention. Contact Metav Werkzeuge for specification support and to confirm fitment of the Teknik Makina SEL 2525 clamping holder for immediate integration — reach our consultants at info@metav-werkzeuge.com or by phone on +49 2822 7131930 Technical data Article number: D511TM Manufacturer: Teknik Makina Model designation: SEL 2525 Description: Clamping holder 16 IR Facts Head width: 25 mm Holder width: 25 mm Cutting height: 30 mm Overall length: 150 mm Weight: 0.753 kg Special features For 16 IR indexable inserts Left‑hand cutting direction Shank designation: M16‑IR16 Compact SEL 2525 geometry Positive insert clamping FAQ What inserts are compatible with this holder? The clamping system is designed for 16 IR indexable inserts; the holder accepts standard 16 IR geometry. Is the holder suitable for left‑hand cutting only? Yes, this variant is specified for left‑hand cutting direction and is marked accordingly for correct mounting. What are the key dimensions to check for turret fitting? Important dimensions include the 25×25 mm head and shank profile, 30 mm cutting height and 150 mm overall length; verify these against the machine tool envelope. How heavy is the holder and does that affect turret balance? The holder weighs 0.753 kg; its moderate mass aids balance considerations on multi‑station turrets compared with larger, heavier holders. Which model designation should be ordered for stock management? Order under the SEL 2525 designation and reference SKU D511TM to ensure the correct Teknik Makina clamping holder is supplied. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of a compact, right‑hand external threading solution that pairs stable clamping with broad insert compatibility; its ISO SER 2525 design and acceptance of 22 ER indexable inserts simplify inventory and reduce setup time. Order the tool directly via Metav Werkzeuge or consult the technical team for tailored integration. Clamping holder D505TM (Teknik Makina) — Right‑hand external threading, for 22 ER indexable inserts The clamping holder D505TM is a right‑hand toolholder engineered for external threading tasks, offering standardised fitment and a compact 25 x 25 mm cutting head suitable for workshop and small‑batch production environments Right‑hand external threading Compatible with 22 ER indexable inserts Compact 25 x 25 mm cutting head 150 mm overall length for stable reach Increased throughput through standardised insert compatibility The holder's acceptance of 22 ER indexable inserts and the ISO SER 2525 designation create a practical, rational advantage: fewer spare parts and quicker changeovers. By matching a common insert family and a recognised interface, the unit reduces inventory complexity and shortens set‑up times on the machine bench, which in turn helps maintain steady cycle times on repetitive threading operations. This focus on compatibility translates into measurable productivity gains without the need for specialist inserts. Consistent clamping for repeatable results A robust clamping concept is central to repeatable thread quality. The clamping assembly is secured with an M4x15 screw driven by a T15 Torx key and is supported by the TA062 U plate and BSP010 shim for precise alignment. The compact 25 x 25 mm cutting head and a 30 mm cutting height provide tool‑to‑workpiece rigidity, while the 150 mm overall length balances reach and stability. At 0.74 kg, the unit is light enough for quick handling yet substantial enough to resist chatter, delivering reliable surface finish and thread form across production runs. Built for machinists and production workshops Designed for lathes and turning centres where right‑hand external threads are required, the holder fits the M22‑ER22 bar designation and integrates into standard tool posts. Its configuration suits toolrooms, contract manufacturers and small series production where flexibility, fast tool changes and dependable clamping are priorities. The engineering focus is on lowering total cost of ownership through reduced downtimes and predictable performance, making the holder a practical choice for teams seeking efficient, standards‑based tooling solutions. Contact Metav Werkzeuge today for bespoke advice on integrating the Teknik Makina D505TM clamping holder into existing setups and to secure reliable supply from our Emmerich stock by phone +49 2822 7131930 or email info@metav-werkzeuge.com Technical data Article number: D505TM Manufacturer: Teknik Makina Product: Clamping holder for external threading (right) ISO designation: SER 2525 Core technical data Overall length: 150 mm Weight: 0.74 kg Holder height: 25 mm Holder width: 25 mm Cutting head width: 25 mm Cutting height: 30 mm Special features Compatible with 22 ER indexable inserts Bar designation: M22‑ER22 Cutting direction: right‑hand Torx screw: M4x15 Torx key: T15 U plate: TA062 Shim: BSP010 FAQ What insert type does this holder accept? The D505TM holder accepts 22 ER indexable inserts and is designed for standard insert families to simplify stocking and changeover procedures. Is the holder suitable for external threading only? The unit is configured for right‑hand external threading, optimised for external thread production on lathes and turning centres. What fasteners and accessories are included or required? The clamping assembly uses an M4x15 Torx screw (Torx T15). Alignment and mounting reference parts include the TA062 U plate and BSP010 shim. Which bar or shank designation is compatible with the holder? The holder is specified with the M22‑ER22 bar designation, enabling integration with matching tool bars and systems. How does the holder support stable machining and surface finish? The combination of a 25 x 25 mm cutting head, 30 mm cutting height and a 150 mm overall length provides a balance of rigidity and reach, reducing vibration and improving thread consistency. Teknik Makina: Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Combining a compact 25 x 25 mm cutting head, left-hand cutting orientation and compatibility with 22 IR indexable inserts, this clamp holder delivers stable, repeatable performance in turning operations; order the component via Metav Werkzeuge or consult their specialists for application advice. Clamp holder D513TM — left-hand holder for 22 IR indexable inserts (Teknik Makina) Clamp holder D513TM is a left-hand turning tool holder designed for indexable 22 IR inserts, providing a compact solution for lathe tooling and constrained setups. Left-hand cutting direction Compatible with 22 IR indexable inserts Cutting head 25 x 25 mm Overall length 150 mm, weight 0.749 kg Consistent clamping for accurate turning cycles The D513TM clamp holder is engineered to ensure stable clamping and consistent cutting geometry when used with 22 IR indexable inserts. The ISO designation SEL 2525 denotes a standardised tool interface that simplifies tool change routines and reduces set-up time. Left-hand cutting orientation is specified for operations where the insert engages the workpiece from the opposite approach compared with right-hand tools; this distinction reduces unexpected axial forces and contributes to predictable chip flow and tool life. The result is improved process reliability and reduced rework in production environments. Space-saving design that improves access and setup A compact cutting head of 25 x 25 mm and a cutting height of 30 mm make the holder suitable for confined work zones and multi-tool turrets. The moderate overall length of 150 mm balances reach and rigidity, allowing access to tight bores while maintaining sufficient tool support to resist chatter. For workshops where machine real estate is limited, the reduced envelope simplifies fixture design and minimises interference with neighbouring tools, helping to maintain uninterrupted production flow. Industrial-ready specification and easy integration With a nominal mass of 0.749 kg and a shank designation of M22- IR22, the holder integrates with common bar and turret systems used in turning centres. Compatibility with the 22 IR insert format provides access to a broad range of grades and geometries for steel, stainless and alloyed turning applications. The left-hand cutting direction and standard ISO form permit straightforward substitution in existing tool cycles without need for extensive programme changes. For further technical integration—such as verifying insert seat geometry or turret clamping—Metav Werkzeuge’s technical advisors can provide the necessary documentation and application support. Contact Metav Werkzeuge to specify the Clamp holder D513TM for left-hand turning operations and arrange tailored supply or technical guidance from Emmerich: info@metav-werkzeuge.com | +49 2822 7131930 Technical data Article number: D513TM Manufacturer: Teknik Makina SKU: D513TM ISO designation: SEL 2525 Compatible insert: 22 IR Shank designation: M22- IR22 Cutting direction: left Overall length: 150 mm Cutting head width: 25 mm Holder width: 25 mm Holder height: 25 mm Cutting height: 30 mm Weight: 0.749 kg FAQ Which insert types fit this holder? The clamp holder D513TM accepts 22 IR indexable inserts; Teknik Makina specifies the insert format for reliable seat fit and repeatability. What does left-hand cutting direction mean for machining? Left-hand cutting indicates the tool is intended for operations where the insert engages the workpiece in the opposite direction to right-hand tools; the D513TM’s left-hand orientation suits specific lathe setups and turning sequences. What are the principal dimensions to check for turret mounting? Key values for the D513TM are overall length 150 mm, cutting head 25 x 25 mm and cutting height 30 mm; these figures support integration planning for turrets and bar setups. Is the holder suitable for production use on CNC lathes? The D513TM is specified for industrial turning with standard interfaces (SEL 2525, shank M22- IR22) and a weight of 0.749 kg, making it appropriate for stable, repeatable production work. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of the combination of secure clamping, standardised compatibility and compact dimensions to streamline external threading operations; order the toolholder directly via Metav Werkzeuge or contact our consultants for application advice. Toolholder D266-1TM — Left‑hand external threading holder by Teknik Makina The Toolholder D266-1TM is designed for secure clamping in external threading applications and accepts 22 IR indexable inserts for left‑hand cutting operations. Left-hand cutting direction for reverse threads Compatible with 22 IR indexable inserts ISO designation AL 2525 for standardised fit Robust 150 mm length and 0.748 kg weight Faster set‑up and standardised compatibility for production workflows The D266‑1TM has been engineered to reduce downtime through standardisation and clear compatibility. With the ISO AL 2525 designation and the M22‑IR22 shank identification, the holder integrates with existing tool systems and inventory structures, which simplifies ordering and reduces the need for bespoke adapters. Its acceptance of 22 IR indexable inserts means inserts can be changed quickly without re‑profiling, delivering measurable savings in set‑up time and increasing throughput on repetitive threading tasks. This focus on process efficiency makes the holder a pragmatic choice for machine shops seeking predictable cycle times and lower tool‑room complexity. Compact dimensions that support rigidity and consistent thread quality Designed with a 150 mm overall length, a 25 mm head width and a 25 mm body height, the holder balances accessibility and stiffness. The specified cutting head width 25 mm and cutting height 30 mm concentrate mass near the cutting zone to reduce chatter and maintain thread form, while the modest mass of 0.748 kg keeps dynamic loads manageable on the toolpost. These dimensional choices translate into superior rigidity in many lathe setups, which helps produce repeatable external threads with fewer reworks. For operations where machine space is limited, the compact footprint also aids positioning and tool clearance without compromising functional stability. Practical advantages for workshop logistics and tooling strategy Beyond machining benefits, the design supports a pragmatic tooling strategy. Compatibility with common insert formats and the clear labelling of the holder (ISO and shank designation) means fewer variants are required in the cutting tool store, aiding stock control and procurement. The left‑hand cutting orientation is immediately identifiable for reversing thread tasks, minimising selection errors during changeovers. Where traceability matters, the SKU and technical marking allow for quick identification and replacement, supporting uninterrupted production schedules and straightforward tool management within a mixed fleet of machines. For reliable left‑hand external threading with standardised insert compatibility, request Teknik Makina's D266‑1TM through Metav Werkzeuge — our consultants in Emmerich are available to advise on fitment and workshop integration. Technical data SKU: D266-1TM Manufacturer: Teknik Makina Product: Toolholder for external threading (Klemmhalter) ISO designation: AL 2525 Shank designation: M22- IR22 Compatible inserts: 22 IR Cutting direction: Left Facts Overall length: 150 mm Holder width: 25 mm Holder height: 25 mm Cutting head width: 25 mm Cutting height: 30 mm Weight: 0.748 kg ECLASS: 21181004 Special features Designed for external threading applications Left‑hand cutting for reverse threads Accepts indexable 22 IR inserts Standardised ISO fit for easy integration Clear shank identification M22‑IR22 FAQ What insert type fits this holder? The holder accepts 22 IR indexable inserts; the designation M22‑IR22 indicates the matching shank/interface. Is the toolholder suitable for reverse threads? Yes, the D266‑1TM is specified with a left‑hand cutting direction suitable for external reverse threading. Which standard ensures interchangeability? Interchangeability is supported by the ISO AL 2525 designation and the M22‑IR22 shank marking. How does the holder support machining stability? Compact dimensions (150 mm length, 25 mm width/25 mm height) concentrate rigidity at the cutting zone, reducing chatter and improving thread repeatability. Can the holder be used across different lathes without adapters? The ISO designation and shank identification are intended to match common toolposts and reduce the need for special adapters, depending on the machine's turret or toolpost configuration. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com

Take advantage of the combination of precise compatibility, robust clamping and easy integration into existing turning setups for reliable cycle times; order the SRDCN 2525 clamp holder directly via Metav Werkzeuge or ask our consultants if needed. SRDCN 2525 clamp holder — for RCMT indexable inserts, 25 x 25 mm shank The SRDCN 2525 clamp holder designed for turning operations with RCMT 1204 indexable inserts, offering a neutral cutting direction for versatile use in mixed cutting programmes. SRDCN 2525 toolholder design Compatible with RCMT 1204 inserts Neutral cutting direction for versatility 25 mm shank height and 150 mm length Consistent compatibility to keep production moving The SRDCN 2525 clamp holder ensures compatibility with common turning inserts such as RCMT 1204, reducing tool change complexity and helping maintain steady throughput. The ISO designation corresponds to a 25 x 25 mm shank, which is a standard size for many turret and toolpost setups; this standardisation simplifies inventory and changeover planning. With an overall length of 150 mm, the holder balances reach and rigidity, enabling stable cutting conditions across a range of diameters. The emphasis here is on predictable performance: the combination of standard dimensions and proven insert interface supports repeatable process set-up and shorter machine downtime between operations. Secure clamping for repeatable machining accuracy Engineered for strong fixation, the holder uses an M12 clamping arrangement to secure inserts reliably during interrupted cuts and heavy turning. The clamping geometry and robust construction translate into stable tool positioning and consistent part finish, with a cutting head width of 12.5 mm and a cutting height of 38 mm that suit typical RCMT insert geometries. At 0.668 kg the component offers a practical mass that contributes to vibration damping without adding unnecessary load to the turret. These attributes combine to deliver measurable benefits in accuracy and surface quality, especially in batch production where repeatability is essential. Versatile orientation and straightforward maintenance A neutral cutting direction gives this holder flexibility to be used in both conventional and reverse orientations where the machine set-up or operator preference dictates. The clamp-style interface allows quick index-and-clamp insert changes, reducing operator handling time and simplifying master data for tool management systems. The design focuses on durability and ease of inspection: routine checks of the clamping screw and insert seat keep the system within tolerance and extend service intervals. For workshops seeking an effective mix of adaptability and low-maintenance operation, this toolholder supports steady productivity with minimal administrative overhead. Contact Metav Werkzeuge for tailored advice or to secure stock of the Teknik Makina SRDCN 2525 clamp holder (SKU D278TM) and receive guidance on integration into existing tool assortments Technical data Article number: D278TM Manufacturer: Teknik Makina Product: SRDCN for RCMT Indexable Inserts ISO designation: SRDCN 2525 Core data Overall length: 150 mm Shank height: 25 mm Shank width: 25 mm Cutting head width: 12.5 mm Cutting height: 38 mm Weight: 0.668 kg Clamping screw/thread: M12 Cutting direction: neutral Special features Compatible with RCMT 1204 inserts ISO: SRDCN 2525 Neutral cutting direction M12 clamping screw Clamp-style insert fixation Designed for turning operations FAQ Which inserts are compatible with this toolholder? The SRDCN 2525 clamp holder is compatible with RCMT 1204 indexable inserts and accepts the standard insert geometry associated with that designation (SKU D278TM, Teknik Makina). What are the shank dimensions and how do they affect mounting? The holder uses a 25 x 25 mm shank (ISO SRDCN 2525), a common format that fits many turret and toolpost interfaces for secure mounting. Is the holder suitable for both left and right hand turning? Yes, the neutral cutting direction enables use in multiple orientations, providing flexibility for conventional and reverse turning set-ups. What clamping thread is used for the insert screw? Clamping is implemented with an M12 screw thread to provide secure fixation under typical turning loads. How should the holder be maintained to ensure longevity? Regular inspection of the clamping screw and insert seat is recommended; keep contact surfaces clean and replace worn screws or clamping parts to retain repeatable performance. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Benefit from precise, secure clamping with a compact 25 x 25 mm head and a 36 mm cutting height that supports ER27 indexable inserts; the SER 2525 design speeds set-up and reduces vibration for cleaner threads. Order directly via Metav Werkzeuge or consult our advisors for application guidance and rapid delivery. Clamping holder SER 2525 — Right‑hand external‑thread holder, 25 x 25 mm | Teknik Makina A robust clamping holder SER 2525 engineered for right‑hand external threading; compatible with ER27 indexable inserts and designed for use with M27‑ER27 shanks. Secure clamping for ER27 indexable inserts Compact 25 x 25 mm head profile Right‑hand external-thread orientation Torx T20 fastening with M5x18 screw Consistent thread quality through precise clamping The SER 2525 holder provides a stable tooling base that improves thread finish by reducing micro‑movement during cutting. The ER27 insert interface and rigid clamping geometry ensure repeatable positioning, which translates into fewer rejects and less rework. With a 36 mm cutting height, the design balances reach and stiffness so that standard external‑thread operations run more smoothly and predictably. Fast integration into existing toolholders and setups Designed for straightforward mechanical integration, the holder accepts a M27‑ER27 shank and measures 150 mm overall length, keeping tool projection manageable in typical lathes and turning centres. The slim 25 x 25 mm head and the Torx T20 fastening with M5x18 screw allow quick insert changes and secure clamping, while the modest mass (0.791 kg) minimises imbalance on rotating tooling systems. These measurable traits support faster set‑ups and lower machine idle time. Reliable operation and application guidance for workshops The right‑hand threading orientation and compatibility with 27 ER turning plates make this holder suitable for a wide range of external‑threading tasks in production and maintenance environments. Robust fastening minimises insert movement and improves operator confidence during extended cycles. If uncertainty remains about specific machining parameters or insert selection, technical advice is available from Metav Werkzeuge, whose supply reliability and broad product range support consistent workshop performance. Contact Metav Werkzeuge for application advice and to arrange prompt delivery from Emmerich — technical consultants are available to specify the right holder configuration for the workshop Technical data Article number: D491TM Brand: Teknik Makina eCl@ss: 21181004 Facts Head width: 25 mm Head height: 25 mm Cutting height: 36 mm Overall length: 150 mm Weight: 0.791 kg Torx key: T20 Torx screw: M5x18 Compatible inserts: 27 ER Shank designation: M27‑ER27 ISO designation: SER 2525 Cutting direction: right Special features U‑plate: TA064 Suited for outside threading (right) Files / documentation available Compact head for reduced overhang FAQ What insert type is compatible with this holder? The holder is compatible with 27 ER indexable inserts; the clamping geometry is matched to ER27 plate dimensions for secure seating. Is the holder suitable for right‑hand external threading? Yes, this clamping holder is configured for right‑hand external‑thread machining and is optimised for that cutting direction. Which shank/socket does the holder fit? It is intended for use with M27‑ER27 shank/toolholder arrangements and carries the ISO designation SER 2525. What fastening hardware is supplied or required? The holder uses a Torx T20 fastening system with an M5x18 screw for insert clamping; standard Torx tools facilitate quick maintenance. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of secure clamping for 16 IR indexable inserts, combined with a left-hand cutting orientation and compact 32 mm head dimensions for improved rigidity in turning operations; order directly via Metav Werkzeuge or consult the technical team for integration advice. Clamping holder SEL 3232 (16 IR) — left-hand cutting by Teknik Makina A compact and robust Clamping holder SEL 3232 designed for indexable inserts of the 16 IR series, intended for left-hand turning on lathes and compatible boring-bar setups Compatible with 16 IR indexable inserts Left-hand cutting orientation 32 mm head height and width 170 mm overall length Improved process stability through secure clamping The holder provides secure clamping of 16 IR indexable inserts, delivering consistent seating and repeatable positioning during turning cycles. Designed with a low centre of gravity and a mass of 1.417 kg, the construction reduces chatter and improves surface finish by increasing rigidity at the cutting point. The clamping mechanism is straightforward and durable, making it suitable for routine production work and short-changeover maintenance procedures. This results in fewer re‑settings and more predictable tool life under stable cutting conditions. Compact dimensions that enhance rigidity and clearance Compact dimensions — a head height and width of 32 mm and an overall length of 170 mm — mean the holder combines stiffness with practical reach. The modest footprint minimises lever arm effects while retaining sufficient clearance for insert geometry and chip evacuation. A cutting height of 30 mm has been selected to match common toolpost and turret interfaces, helping to maintain the correct cutting line without additional shims. These measurements support efficient toolholders layouts where space and stability are both critical. Easy integration with existing tooling and workshop workflows Integration is simplified by the ISO designation SEL 3232 and compatibility with standard boring-bar interfaces such as P16- IR16. The left-hand cutting specification is clearly defined, avoiding installation errors in mixed-tool setups. The unit’s balanced weight and standardised dimensions permit straightforward mounting and predictable dynamic behaviour on CNC lathes and conventional machines alike. For workshops seeking dependable replacement holders or modular toolroom expansion, the product offers a low‑risk option backed by Metav’s quality filter and supply chain reliability. Contact Metav Werkzeuge in Emmerich for technical consultation and procurement of the Teknik Cutting Tools SEL 3232 clamping holder — phone +49 2822 7131930 or email info@metav-werkzeuge.com Technical Data Article number: D512TM Manufacturer: Teknik Makina SKU: D512TM Facts Overall length: 170 mm Head height: 32 mm Head width: 32 mm Cutting height: 30 mm Weight: 1.417 kg Special features ISO designation: SEL 3232 For indexable inserts: 16 IR Compatible boring bar: P16- IR16 Cutting direction: left FAQ Which insert size fits this holder? The holder accepts 16 IR indexable inserts; the SEL 3232 is designed specifically for that insert format. Is the cutting direction left or right? This model is configured for left-hand cutting; the SEL 3232 should be used where left-hand tool orientation is required. Which boring bars is the holder compatible with? Compatibility includes standard P16 interfaces such as P16- IR16, enabling direct mounting to matching boring bars. What are the key dimensions to check before fitting? Overall length 170 mm, head height 32 mm, head width 32 mm, cutting height 30 mm and weight 1.417 kg. Is this holder suitable for production use on CNC lathes? Yes, the SEL 3232 is designed for stable, repeatable clamping and is suitable for routine production work when used with the correct inserts and machine settings. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Robust clamping and a defined 30° cutting angle deliver consistent chip control and repeatable results; compatible with RCMT 0803 indexable inserts and supplied in the SRGCL 2020 ISO format — order via Metav Werkzeuge or consult Metav's specialists for application support. Klemmhalter SRGCL 2020 — SRGC toolholder for RCMT indexable inserts (left‑hand, 30°) The Klemmhalter SRGCL 2020 is a left‑hand turning toolholder engineered for use with RCMT 0803 indexable inserts, optimised for repeatable turning and secure clamping in workshop and production environments. Compatible with RCMT 0803 inserts 30° cutting angle for accurate engagement 125 mm overall length for stability Left‑hand orientation for reverse turning Consistent machining through defined geometry and insert compatibility The SRGC design provides a predictable cutting geometry that supports stable chip formation and dimensional accuracy. With a 30° cutting angle and compatibility with RCMT 0803 indexable inserts, the holder enables straightforward insert changes and fast restoration of cutting performance. The ISO designation SRGCL 2020 denotes the toolholder format and mounting envelope, simplifying tool library management. This combination reduces downtime and contributes to a steady production flow when used in repetitive turning tasks. Compact construction that enhances rigidity and tool life A compact but robust profile — 125 mm overall length, 25 mm head width and 20 mm holder width — helps to keep overhang low and stiffness high. The controlled mass of 0.411 kg balances inertial forces while the 25 mm cutting height aligns the insert for optimal chip evacuation. These dimensions translate into less vibration during cutting and improved surface finish, which benefits throughput and downstream processes. The nominal proportions also make the holder suitable for confined tool posts on smaller CNC lathes. Safe clamping and simple handling for faster set‑ups Clamping is executed using the specified shank interface and the K08 designation for the mount system, which matches common toolpost adapters. The design prioritises secure clamping and repeatable seat location so that indexable inserts can be exchanged without recalibrating the tool centreline in most fixtures. Indexable inserts allow a worn cutting edge to be rotated or replaced quickly, keeping machines productive and maintenance straightforward. Recommended applications and production benefits This left‑hand SRGC toolholder is suited to general turning and finishing operations where reverse or counter‑direction cuts are required. By pairing the holder with RCMT 0803 inserts, the system is particularly effective for medium‑duty turning tasks that demand consistent edge position and predictable tool behaviour. The combination of compact geometry and standardised insert format supports efficient inventory management, reduces setup complexity, and accelerates changeovers on mixed‑volume production runs. Contact Metav Werkzeuge for tailored application advice and fast supply of the SRGCL 2020 left‑hand toolholder — direct shipment from Emmerich with technical consultation available Technical data Article number: D293TM Manufacturer: Teknik Makina ISO designation: SRGCL 2020 Core measurements Overall length: 125 mm Holder height: 20 mm Holder width: 20 mm Head width: 25 mm Cutting height: 25 mm Weight: 0.411 kg Cutting angle: 30° Special features Compatible with: RCMT 0803 indexable inserts Cutting direction: left Shank designation: K08 Designation English: SRGC for RCMT Indexable Inserts ECLASS: 21181004 FAQ What insert type fits this toolholder? The SRGCL 2020 toolholder accepts RCMT 0803 indexable inserts, providing quick edge changes and standardised insert handling. Is the holder suitable for left‑hand turning only? Yes, the holder is specified for left‑hand cutting direction and is intended for reverse turning operations. What is the overall length and how does it affect stability? The 125 mm overall length keeps overhang low to improve rigidity and surface finish during turning. Which shank or mounting designation is used? The holder uses the K08 shank designation compatible with common toolpost adapters and clamping systems. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

The combination of a compact 125 mm overall length, stable clamping and a 30° cutting angle delivers reliable turning performance in restricted setups; excellent for repeatable workshop production. Order the clamping holder directly via Metav Werkzeuge or ask our consultants if needed. Clamping holder SRGCR 2020 — SRGC for RCMT indexable inserts, right-hand, 30° cutting angle (Teknik Makina) The Clamping holder SRGCR 2020 is a right-hand toolholder designed for turning with RCMT 1204 indexable inserts, optimised for compact toolpaths and secure insert retention across general workshop applications Right-hand cutting orientation Accepts RCMT 1204 inserts 30° cutting angle for profile control Compact 125 mm overall length Consistent chip control and repeatable clamping improve surface quality The SRGCR 2020 is built for reproducible turning cycles where secure clamping and consistent geometry matter. The positive 30° cutting angle supports controlled chip flow and reduces vibration when machining simple profiles or finishing passes. By combining a robust insert seat with a short overhang, the toolholder reduces the risk of chatter and produces a more uniform surface finish, which directly lowers rework and quality checks. Compact form factor increases rigidity and access in tight spaces A short 125 mm overall length with a 25 mm cutting-head width and 20 mm holder dimensions keeps the centre of gravity close to the spindle, raising rigidity under load. The light mass of 0.422 kg reduces centrifugal stress on the turret while providing stable support for the RCMT 1204 insert family. This compact design is advantageous where access is constrained: it enables closer approach to shoulders and small-diameter features, shortening cycle times through reduced vibrations and fewer tool changes. Clear compatibility and practical terminology for workshop use The holder accepts RCMT 1204 indexable inserts and aligns to a common ISO-style mounting for straightforward replacement. Indexable inserts are small carbide cutting tips that are secured to the seat and can be rotated or replaced when worn, allowing fast return to dimension without regrinding. The toolholder’s right-hand orientation specifies the cutting direction for conventional turning setups; match the holder orientation with the machine programme and insert geometry to ensure correct cutting action and safe operation. For reliable right-hand turning with consistent repeatability, contact Metav Werkzeuge for supply and technical advice on Teknik Cutting Tools clamping holders; phone +49 2822 7131930 or email info@metav-werkzeuge.com Technical data Article number: D288TM ISO designation: SRGCR 2020 Type: SRGC for RCMT indexable inserts Manufacturer: Teknik Makina Dimensions & weight Overall length: 125 mm Holder height: 20 mm Holder width: 20 mm Cutting-head width: 25 mm Cutting height: 25 mm Weight: 0.422 kg Cutting angle: 30° Compatibility & features Suitable for RCMT 1204 inserts Right-hand cutting direction Shank designation: K12 SKU: D288TM FAQ Which inserts fit this holder? The holder is designed for RCMT 1204 indexable inserts; refer to the insert catalogue for matching grades and geometries when using the SRGCR 2020 (Teknik Cutting Tools, SKU D288TM). Is the toolholder suitable for right-hand turning only? Yes, the toolholder is specified for right-hand orientation, intended for conventional right-hand turning operations. What are the key dimensions to check for turret clearance? Check the 125 mm overall length, 25 mm cutting-head width and 20 mm holder dimensions to ensure turret clearance and correct tool projection for the intended operation with the SRGCR 2020. How does the 30° cutting angle affect machining? A 30° cutting angle promotes controlled chip formation and smoother engagement on profile work, aiding surface finish while maintaining effective material removal on finishing passes. What is the weight and how does it affect stability? The holder weighs 0.422 kg; lower mass with a compact design reduces overhang and improves rigidity, contributing to more stable machining for shorter tool extensions. Manufacturer / Responsible: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Reliable right‑hand clamping with a 30° cutting angle and a 25 mm shank for stable turning operations; combined with a 150 mm overall length this holder integrates cleanly into existing tool setups. Benefit from secure insert seating and consistent chip control — order via Metav Werkzeuge or consult our advisors for application guidance. SRGCR 2525 Clamping Holder — Right-hand, 30° for RCMT 0803 (Teknik Makina) The SRGCR 2525 clamping holder is a right‑hand indexable insert holder developed for turning operations with RCMT 0803 format inserts, offering a compact, rigid solution for routine and precision machining. Compatible with RCMT 0803 inserts Right‑hand cutting direction 30° cutting angle for controlled chip flow 150 mm overall length Consistent precision for productive turning The SRGCR 2525 follows a straightforward design that prioritises repeatability and process stability. The indexable inserts concept means the cutting edge can be renewed in seconds without regrinding, reducing non‑productive time and keeping cycle times low. A defined 30° cutting angle helps direct chips away from the workpiece and toolpost, improving surface finish and reducing rework. For customers who measure productivity in throughput and uptime, a reliable insert holder translates directly into fewer interruptions on the shop floor. Compact dimensions that enhance rigidity A compact cross‑section results in measurable stiffness at the cutting point. The holder features a 25 mm shank height, a 32 mm cutting‑head width and a 30 mm cutting height, which together deliver a stable clamping platform under moderate cutting forces. The moderate mass — approximately 0.71 kg — balances inertial stability with easy handling during tool changes. These dimensional values support consistent vibration damping and predictable tool life when paired with appropriate insert grades. Compatibility and straightforward mounting Designed for the widely used RCMT 0803 insert format, the holder accepts standard indexable inserts and is mounted via a M08 fastening interface. The 150 mm overall length provides reach for common turning tasks while keeping the overhang minimal to preserve rigidity. The right‑hand cutting orientation is suited to conventional turning directions; when planning tooling layouts, ensure the holder orientation matches lathe spindle rotation. The simple clamping mechanism ensures fast insert replacement and secure seating without specialised fixtures. Practical integration and workshop benefits Beyond geometry and fit, this indexable insert holder supports predictable tool management: fewer regrinds, faster set‑ups and straightforward inventory of cutting tips. For workshops aiming to streamline tooling kits, the holder’s compatibility with a standard insert family reduces the number of distinct part numbers to stock. Technical advisors can recommend insert grades and cutting parameters to suit specific materials and priorities, combining operational efficiency with dependable part quality. The design emphasises practical uptime improvements rather than unnecessary complexity. Consult Metav Werkzeuge for technical selection and secure the Teknik Makina SRGCR 2525 clamping holder for reliable right‑hand turning with RCMT 0803 inserts Technical data Article number: D282TM Manufacturer: Teknik Makina Designation: SRGC for RCMT Indexable Inserts ISO designation: SRGCR 2525 Core technical data Shank height: 25 mm Cutting head width: 32 mm Shank width: 25 mm Cutting height: 30 mm Overall length: 150 mm Weight: 0.71 kg Cutting angle: 30° Cutting direction: right Features and compatibility For indexable inserts RCMT 0803 Mounting bore designation: M08 Right‑hand holder for turning applications SRGCR 2525 geometry FAQ Which inserts fit this holder? The SRGCR 2525 clamping holder is designed for RCMT 0803 indexable inserts and accepts the standard geometry and clamping of that insert family. Is this a right‑hand or left‑hand toolholder? This toolholder is a right‑hand turning holder; ensure the orientation matches the lathe’s spindle rotation for safe operation. What is the overall length and how does that affect rigidity? The overall length is 150 mm; shorter overhangs contribute to improved rigidity and reduced vibration compared with longer tool extensions. Which mounting screw or bore is required? The holder uses an M08 mounting designation for the clamping screw interface; verify compatibility with existing tool posts before installation. Can the holder be used for heavy roughing cuts? The holder is intended as a compact, rigid solution; heavy roughing may demand larger shank dimensions or different holder families — consult tooling data for specific cutting forces and insert grades. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of a robust combination of precise clamping, proven ISO compatibility and a compact 150 mm reach for stable right‑hand turning operations; order this holder directly via Metav Werkzeuge or consult our specialists for tailored tooling advice. SRGC Clamping Holder — SRGCR 2525 for RCMT 10T3, right‑hand (Teknik Cutting Tools) The SRGC for RCMT Indexable Inserts is a right‑hand clamping holder engineered for conventional turning tasks with RCMT 10T3 inserts, offering a compact 150 mm reach and secure M10 mounting for consistent setup. Right‑hand holder for RCMT 10T3 inserts ISO SRGCR 2525 designation for compatibility 150 mm overall length for stable reach Robust clamping with 30° cutting angle Precision compatibility that reduces setup time The SRGC clamping system is designed around ISO SRGCR 2525 compatibility, making it immediately suitable for RCMT 10T3 indexable inserts. This standardised interface simplifies tooling selection and stock management in the workshop: a single holder type covers a wide range of turning tasks when matched with the appropriate insert geometry. The combination of a compact 150 mm overall length and a moderate mass (approx. 0.72 kg) delivers a stable platform that reduces vibration and shortens adjustment cycles, which in turn decreases non‑productive time on the lathe. Stable cutting geometry for consistent surface quality A defined 30° cutting angle and a 30 mm cutting height are the core of the holder’s cutting geometry: these dimensions promote reliable chip evacuation and predictable insert engagement. The 32 mm cutting‑head width and 25 mm body width ensure a balanced stiffness-to-clearance ratio, so the clamping mechanism maintains repeatable cutter position under varying loads. The integrated M10 fixing provides secure attachment to standard toolposts, supporting consistent cutting forces and helping to extend the life of both the insert and the toolholder through reduced micro‑movement. Workshop benefits: fewer tool changes, more uptime Designed for routine and small‑batch production environments, this indexable insert holder brings operational benefits beyond raw dimensions. Clear standardisation (ISO designation) and compatibility with RCMT‑type inserts simplify replenishment and stock control, while the right‑hand orientation suits the majority of conventional turning setups. For procurement and maintenance teams the result is a reliable, easy‑to‑manage component that lowers the risk of incorrect fits and reduces downtime. Technical buyers will appreciate the pragmatic balance of reach, clamping security and compatibility that supports consistent part quality across shift patterns. Choose the Teknik Cutting Tools SRGC holder for dependable right‑hand turning and contact Metav Werkzeuge in Emmerich for personalised guidance and rapid supply from a trusted European quality partner Technical Data Article number: D286TM Manufacturer: Teknik Makina Product: SRGC clamping holder for RCMT indexable inserts ISO designation: SRGCR 2525 eClass: 21181004 Facts Overall length: 150 mm Weight: 0.72 kg Holder height: 25 mm Cutting head width: 32 mm Body width: 25 mm Cutting height: 30 mm Special features Compatible inserts: RCMT 10T3 Cutting direction: Right Cutting angle: 30° Shank bore / thread: M10 Suitable for indexable insert turning applications FAQ Which indexable inserts fit this holder? The holder accepts RCMT 10T3 indexable inserts; compatibility is ensured by the ISO SRGCR 2525 interface specified for this Teknik Cutting Tools clamping holder (SKU D286TM). Is this holder suitable for left‑hand turning? This model is configured for right‑hand turning; for left‑hand operations a corresponding left‑hand toolholder should be selected. What are the key dimensions to check before ordering? Important dimensions include the 150 mm overall length, 30 mm cutting height and 32 mm cutting‑head width; these values determine reach and clearance for the intended turning task. How is the holder mounted to the toolpost? Mounting is achieved via the M10 shank bore and standard clamping interfaces; the M10 fixing helps to secure the holder and maintain repeatable cutter position during cutting. Will this holder improve insert life? The combination of a stable body, defined 30° cutting angle and secure clamping tends to reduce micro‑movement and vibration, which can contribute to more consistent tool wear and extended insert life when applied correctly. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of the combination of precise insert compatibility, robust clamping geometry and predictable chip control for reliable turning operations; order the holder directly via Metav Werkzeuge or contact the consultants for application advice. SRGCR 2525 clamping holder — SRGC for RCMT indexable inserts, right-hand, 30° cutting angle (Teknik Makina) The SRGCR 2525 clamping holder is a right-hand turning toolholder designed for use with RCMT 1204 indexable inserts, providing stable clamping and consistent cutting geometry for external turning operations. Right-hand turning orientation Compatible with RCMT 1204 inserts 30° cutting angle for improved chip control 150 mm overall length for extended reach Consistent clamping for repeatable turning results The holder's shank height 25 mm and head width 32 mm establish a rigid interface between toolpost and cutting edge, reducing chatter and improving surface finish. The ISO designation SRGCR 2525 describes a standardised form factor that simplifies tool selection and replacement in series production. With a defined cutting height 30 mm, setup tolerances are minimised, which shortens machine downtime and supports predictable part tolerances. The result is a measurable improvement in cycle-time stability and fewer reworks when machining batches. Simple insert interchange and stable cutting geometry Designed specifically for RCMT 1204 indexable inserts, the SRGC configuration secures the insert with a proven clamping arrangement; the clamping thread is M12, allowing reliable torque application for secure seat retention. The 30° cutting angle promotes controlled chip flow and reduced cutting forces during right-hand turning, which benefits cycle time and tool life. Compatibility with common insert grades makes the holder suitable for a range of steels and non-ferrous materials when paired with the appropriate grade of insert, enabling flexible use across varied jobs. Reach and balance tuned for production lathes An overall length of 150 mm provides extended reach for operations that require access to deeper profiles or larger workpieces, while the toolholder’s weight of 0.744 kg helps maintain a balance between rigidity and dynamic response on turret or quick-change toolposts. These dimensions support efficient set-up and reduce the need for intermediate fixtures. Where repeatable positioning is critical, the SRGCR profile shortens alignment time and supports consistent centre-to-edge relation across multiple setups. Built to integrate into workshop workflows The SRGCR 2525's form factor and standardised interface simplify inventory and spare-part management for maintenance teams. As an SRGC-style toolholder, it integrates into existing tooling systems with minimal adaptation, supporting both one-off jobs and continuous production runs. If further specification is required for a particular machine or insert grade, Metav’s technical documentation and advisors can be referenced to match insert geometry, grade and cutting parameters to the application, ensuring the best compromise between productivity and component quality. For precision turning tasks that demand stable clamping and predictable chip control, order the Teknik Makina SRGCR 2525 clamping holder via Metav Werkzeuge or request tailored application advice from our consultants in Emmerich Technical data Article number: D290TM Manufacturer: Teknik Makina Product name: SRGCR 2525 clamping holder Designation: SRGC for RCMT indexable inserts Orientation: right-hand Facts Overall length: 150 mm Weight: 0.744 kg Shank height: 25 mm Head width: 32 mm Cutting height: 30 mm Cutting angle: 30° Special features Suitable for RCMT 1204 inserts ISO designation SRGCR 2525 Clamping thread: M12 FAQ Which inserts are compatible with this holder? The holder supports RCMT 1204 indexable inserts and is designed to secure these inserts reliably in the SRGC pocket. Is the toolholder for right- or left-hand turning? This toolholder is configured for right-hand turning applications; the cutting angle and pocket orientation match right-hand feeds. What are the key dimensions for setup planning? Important dimensions include an overall length of 150 mm, shank height 25 mm, head width 32 mm and a cutting height of 30 mm, which help determine reach and clamping clearance. What is the ISO designation and why is it relevant? The ISO designation SRGCR 2525 identifies the holder’s standardized form factor, aiding compatibility checks and simplifying replacement in existing tooling systems. Which clamping screw specification applies to the holder? The clamping interface uses an M12 thread for secure insert retention and consistent torque application. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of the combination of precise clamping, compatibility with common indexable inserts and compact dimensions for reliable turning cycles in production and workshop environments; order the clamping holder directly via Metav Werkzeuge or consult their specialists for procurement and delivery. Klemmhalter D515TM — Left‑hand clamping holder for 22 IR indexable inserts by Teknik Makina Klemmhalter D515TM is a left‑hand clamping holder designed for side turning and lathe tool stations, suitable for industrial and workshop use with 22 IR indexable inserts Left‑hand cutting direction for side turning Compatible with 22 IR indexable inserts SEL 3232 ISO size designation 32 × 32 mm robust clamping dimensions Reliable grip for consistent turning results The clamping solution delivers a stable hold on indexable inserts, which reduces vibration and promotes repeatable part quality. The design accepts 22 IR format inserts and secures them with a form‑fitting seat, so chip geometry remains consistent from cut to cut. This results in improved surface finish and fewer rework cycles, translating into predictable machine uptime and lower total production costs. Familiar terminology such as indexable insert refers to a replaceable cutting tip that can be rotated or changed without replacing the whole tool, improving economy and flexibility in daily machining. Dimensions and mass engineered for workshop compatibility Key dimensions are optimised for common toolpost and turret configurations: 32 mm height, 32 mm width and an overall length of 170 mm, combining compactness with practical reach. The cutting height of 36 mm aligns the insert nose with standard turning centres, simplifying set‑up and avoiding offset errors. A mass of 1.434 kg provides the mechanical inertia needed to dampen chatter without excessive load on the turret. The holder is identified by the ISO reference SEL 3232, enabling quick cross‑referencing in tool lists and ensuring correct replacement parts and fixtures are chosen. Productivity through standardised compatibility Using standard insert sizes reduces tool inventory complexity and shortens changeover times. The holder accepts inserts indicated by P22- IR22, so replacement tips and spare parts are widely available across suppliers. Standardisation supports lean stocking and faster throughput: operators can keep a small range of inserts and still cover many turning tasks. For production planners, this translates into fewer line stoppages due to missing consumables and a more predictable procurement process. Straightforward integration and maintenance The holder is engineered for easy mounting and routine service. Its form and fitting simplify blade seating and clamp checks during shift changes; familiar handling procedures apply because the geometry follows common industrial conventions. Clear markings and the ISO designation make installation verification fast during tool changeovers, and the use of established insert types keeps maintenance predictable. Regular inspection of the clamping surfaces will preserve seating accuracy and extend service intervals, supporting a steady production rhythm. For procurement guidance or to reserve stock of the Teknik Makina D515TM clamping holder, contact Metav Werkzeuge in Emmerich—telephone +49 2822 7131930 or eMail info@metav-werkzeuge.com for delivery options and technical advice Technical data Article number: D515TM Manufacturer: Teknik Makina Product name: Klemmhalter SKU: D515TM Core dimensions Height: 32 mm Width: 32 mm Cutting height: 36 mm Overall length: 170 mm Weight: 1.434 kg Compatibility & features For indexable inserts: 22 IR Compatible insert designation: P22- IR22 ISO designation: SEL 3232 Cutting direction: left FAQ What insert size does this holder accept? The holder accepts 22 IR indexable inserts; replacements labelled for 22 IR will fit the seating. Is the cutting direction right or left? This clamping holder is configured for a left cutting direction, suitable for left‑hand side turning operations. Which ISO size identifies the holder? The toolholder carries the ISO designation SEL 3232, used for reference and replacement matching. What are the main dimensions affecting fit‑up? Key dimensions are 32 mm height, 32 mm width, and 170 mm overall length, with a 36 mm cutting height. Can the holder be used in both workshop and production lathes? Yes; its standard dimensions and compatibility with 22 IR inserts make it suitable for both workshop toolposts and production turrets provided the machine accepts the stated dimensions. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of a robust clamping concept that combines precise seating with durable construction for reliable turning operations; the compact DCXNN 2525 design, paired with compatibility for CN-- 1204 indexable inserts, supports consistent component quality and prolonged tool life — order via Metav Werkzeuge or consult our technical advisers for supply and integration. Clamping holder DCXNN 2525 — clamping holder for CN-- 1204 indexable inserts, 40/45° cutting angle (Teknik Makina) A clamping holder DCXNN 2525 designed to secure CN-- 1204 indexable inserts for stable external turning and profiling in steel machining DCXNN 2525 design for CN-- 1204 inserts 25 mm tool height for stable clamping 40/45° cutting angle compatibility M12 shank thread, 150 mm overall length Achieve consistent results with stable clamping and repeatability The DCXNN 2525 holder is engineered to provide stable clamping that translates into repeatable part geometry and reduced scrap rates. Its iso designation and compact geometry ensure a defined seating plane for the CN-- 1204 style inserts, which means the insert position remains constant from cut to cut. This mechanical consistency simplifies process control and contributes directly to lower rework and improved assembly tolerances. The combination of a solid clamping interface and precise seating supports a longer tool life for both inserts and holder. Designed for demanding steel machining and reliable reach With a nominal tool height of 25 mm and an overall length of 150 mm, the holder offers a balanced compromise between rigidity and reach for external turning tasks. The holder’s compatibility with CN-- 1204 indexable inserts and its 40/45° cutting angle make it suitable for general profiling, facing and light roughing operations in carbon and alloy steels commonly encountered in industrial workshops. The M12 thread on the mounting shank provides a standardised connection for secure attachment in a wide range of toolposts and boring bars, contributing to predictable vibration behaviour and surface finish. The measured mass of 0.756 kg aids stability without unnecessarily increasing inertia. Quick set-up, predictable maintenance and production uptime The DCXNN 2525 centrepiece was developed for straightforward handling and low maintenance in production environments. The clear insert interface reduces indexing time when turning over or replacing CN-- 1204 inserts, while the robust construction minimises the frequency of service interventions. For process engineers this translates into fewer changeovers and a more efficient shift plan. When integrated into a workshop with standard insertion procedures, the holder supports consistent cycle times and contributes to an optimised production flow. For further specification checks or integration advice, technical documentation and images are available on request. Contact Metav Werkzeuge for tailored technical advice on integrating the Teknik Makina clamping holder DCXNN 2525 into existing turning setups and to secure supply directly from Emmerich Technical data Article number: D216TM Manufacturer: Teknik Cutting Tools (Teknik Makina) Facts Overall length: 150 mm Tool height: 25 mm Tool width: 25 mm Cutting head width: 12.5 mm Cutting height: 35 mm Cutting angle: 40° Weight: 0.756 kg Shank/thread: M12 Compatible inserts: CN-- 1204 eClass: 21181004 Special features ISO designation: DCXNN 2525 For DCXNN and DCSNR indexable insert types Suited to external turning and profiling operations Robust steel construction for long service life FAQ What insert types fit this holder? The holder is specified for CN-- 1204 indexable inserts; the DCXNN 2525 seating takes standard CN-- 1204 geometries. Is the holder suitable for external turning in steel? Yes — the geometry and clamping stability make the holder well suited to steel machining operations and standard workshop turning tasks. What mounting thread does the tool use? The holder uses an M12 shank/thread for attachment, offering compatibility with many standard toolposts and bar adaptors. Can the clamping holder be used for profiling and facing? The 40/45° cutting angle and the DCXNN 2525 design support profiling and facing operations, delivering controlled chip flow and stable cutting conditions. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com

Take advantage of a compact, ISO‑specified turning solution that combines secure clamping, a controlled 45° engagement and a standard M12 clamping screw for repeatable results; order the clamping holder directly via Metav Werkzeuge or consult our specialists for application advice. DCSNR 2525 clamping holder — right‑hand external turning, 45° cutting angle (Teknik Makina) The DCSNR 2525 is a robust right‑hand external turning toolholder designed for precision machining with CN-- 1204 indexable inserts, suited to conventional and production turning applications Right‑hand external turning holder 45° cutting angle for controlled engagement Compatible with CN-- 1204 indexable inserts M12 clamping screw, 150 mm overall length High repeatability from a compact clamping design The turning toolholder offers consistent seating and secure clamping thanks to its ISO designation and a standardised clamping interface. With a 45° cutting angle the toolholder reduces radial shock and promotes steady chip evacuation, which translates into improved surface finish and reduced rework. The DCSNR 2525 specification aligns with common workshop tooling standards, enabling straightforward set‑ups on lathes and turning centres and reducing changeover time between jobs. Precision dimensions that support predictable toolpaths Engineered for controlled engagement, the holder presents a 35 mm cutting height and a compact head width of 32 mm, providing stable support for the insert during heavy cuts. The body measures 150 mm overall length with a holder width and height of 25 mm, balancing rigidity and accessibility in cramped toolposts. Weighing 0.774 kg, the assembly is easy to handle while remaining stiff enough to minimise vibration, which helps to maintain tolerances and repeatability across serial production. Practical compatibility and straightforward maintenance Compatibility with CN-- 1204 indexable inserts and a common M12 clamping screw simplifies stock handling and replacement cycles. The right‑hand orientation is specified for external turning operations where directional control of chip flow and tool approach are critical. This toolholder is suitable for workflows that prioritise operational efficiency and predictable tool life, offering a pragmatic solution for workshops that seek to standardise their turning fixtures without complex retrofits. Discuss the Teknik Makina DCSNR 2525 with Metav Werkzeuge to confirm fitment and optimise tooling choices — contact Metav Werkzeuge by e‑mail at info@metav-werkzeuge.com or by phone on +49 2822 7131930 for tailored advice and fast dispatch Technical data Article number: D218TM Manufacturer: Teknik Makina Facts Overall length: 150 mm Weight: 0.774 kg Cutting height: 35 mm Head width: 32 mm Holder width: 25 mm Holder height: 25 mm Cutting angle: 45° Clamping screw thread: M12 Special features ISO designation: DCSNR 2525 For indexable inserts: CN-- 1204 Right‑hand external turning Robust clamping interface for repeatable seating FAQ What insert size does this holder accept? The DCSNR 2525 is designed for CN-- 1204 indexable inserts, matching the insert form and seat geometry for reliable clamping. Is the holder suitable for right‑hand turning only? Yes, the toolholder is specified for right‑hand external turning operations and provides the intended chip flow and approach for that direction. Which clamping screw is required for assembly? Assembly uses an M12 clamping screw as part of the clamping mechanism for secure insert retention. What are the key dimensions to check for fitting in a toolpost? Relevant dimensions include the 150 mm overall length, 25 mm holder width, 25 mm holder height and the 32 mm head width to ensure correct toolpost clearance. Can the DCSNR 2525 be used in production turning centres? Yes, the ISO format and robust clamping make the holder suitable for production environments that use standard CN-- 1204 inserts and require repeatable, stable toolholding. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Benefit from a robust combination of precise insert compatibility, stable clamping and extended reach for consistent turning results; the DSSNR 4040 toolholder brings repeatable performance to serial and single-part production. Order the tool directly via Metav Werkzeuge or consult the specialists for application-specific advice. Klemmhalter — DSSNR 4040 right-hand turning toolholder with 45° cutting angle by Teknik Makina Klemmhalter is a right-hand toolholder designed for versatile turning with SNMG indexable inserts, suited to CNC lathes and shopfloor production where stability and predictable chip control are required. Right-hand turning holder for SNMG inserts 45° cutting angle for versatile turning Overall length 250 mm for deep reaches Robust 3.123 kg construction for stability Improved cycle times through predictable cutting performance The DSSNR 4040 designation identifies a purpose-built clamping solution for SNMG 1906 indexable inserts, offering a consistent 45° cutting angle that balances metal removal and finish quality. The combination of a defined rake geometry and a secure clamping seat reduces vibration and stabilises the cutting edge, which in practice leads to more repeatable cycle times and reduced scrap rates. For production environments that prioritise throughput, this stability enables higher feeds without sacrificing surface integrity, making it an efficient choice for both roughing and light finishing passes. Stable construction and reach for deeper turning tasks A compact head and a long shank translate into tangible workshop benefits: the head width of 40 mm, holder width of 50 mm and an overall length of 250 mm provide the reach required for deeper bores and extended overhangs while maintaining rigidity. The substantial mass (approx. 3.123 kg) and the defined cutting height of 46 mm work together to dampen chatter and improve dimensional stability. In practice, these design choices reduce tool deflection and help to preserve insert life, which contributes to lower tooling costs over longer production runs. Secure clamping and straightforward integration into tool setups The clamping concept is tailored for SNMG 1906 inserts and the ISO designation DSSNR 4040 aids quick identification when configuring tool turrets. The holder is intended for right-hand cutting direction and integrates with a shank designation of S19, allowing consistent repeatability in multi-station setups. Because the design focuses on repeatable seating and firm mechanical fixation, insert indexing and replacement are fast and predictable—benefits that reduce downtime during changeovers and support high-availability manufacturing. Speak with Metav Werkzeuge today to specify the DSSNR 4040 clamping holder for the intended application and benefit from reliable supply and technical guidance from our Emmerich location. Technical Data Article number: D207TM Brand: Teknik Makina Product: Klemmhalter (DSSNR for SNMG Indexable Inserts) ISO designation: DSSNR 4040 Facts Overall length: 250 mm Holder width: 50 mm Cutting head width: 40 mm Holder height: 40 mm Cutting height: 46 mm Cutting angle: 45° Weight: 3.123 kg Cutting direction: right Special features Compatible with SNMG 1906 indexable inserts Shank designation: S19 Right-hand turning toolholder SKU: D207TM Manufacturer: Teknik Makina FAQ Which insert size is compatible with this toolholder? The Klemmhalter is designed for SNMG 1906 indexable inserts; use inserts matching that size for correct seating and clamping. What is the intended cutting direction for the holder? The holder is configured for right-hand cutting direction, optimised for standard lathe orientations. How does the holder support repeatable set-ups? The DSSNR 4040 designation and firm clamping seat ensure repeatable insert location and quick indexing, which improves setup consistency across machines. Is the holder suitable for extended overhangs? With an overall length of 250 mm and a robust build, the Klemmhalter provides reach for deeper turning while maintaining rigidity for many shop applications. What identification should be used when ordering spare holders or matching inserts? Refer to the ISO designation DSSNR 4040, compatible insert type SNMG 1906, and SKU D207TM to ensure the correct item is supplied. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of robust clamping, a compact 20 mm shank and a precise 45° cutting geometry for dependable turning operations; order directly via Metav Werkzeuge or consult our specialists for application-specific advice. PSSN for SNMG Indexable Inserts — PSSNL 2020 by Teknik Makina (left-hand, 45° cutting angle) The PSSN for SNMG Indexable Inserts is a left-hand turning toolholder designed for secure clamping of SNMG 1204 inserts, optimised for stable chip control and predictable turning performance in industrial workshops. Left-hand turning orientation Compatible with SNMG 1204 inserts 45° cutting geometry for consistent chip flow Compact 20 mm shank for stable mounting Precision clamping for consistent turning quality The holder delivers reliable clamping and consistent tool positioning, which reduces vibration and contributes to repeatable surface finishes. Its 45° cutting geometry is designed to improve chip evacuation and maintain cutting forces within predictable limits; this helps to extend insert life and to lower rework rates. By specifying a holder with defined dimensions and geometry, machinists obtain a stable cutting system that supports efficient, process-oriented production. Optimised dimensions for workshop integration and quick set-up With a 20 mm shank, 25 mm head width and 125 mm overall length, the toolholder fits compact toolposts while offering sufficient overhang for typical turning tasks. The modest mass of 0.416 kg aids balance and reduces spindle load during higher-speed operations. These measurable attributes enable planners to integrate the holder into existing setups without major adjustments, shortening setup time and enabling faster switchovers between operations. Clear compatibility and mounting guidance for safe use The device carries the ISO designation PSSNL 2020 and is intended for SNMG 1204 indexable inserts, using the K12 bore specification for insertion and clamping. It is a left-hand toolholder, which means the cutting action is oriented for left-hand turning on the lathe; this should be selected when machining directions and part geometry require opposite tool approach. The defined geometry and standardised interface simplify tool selection and spare-part management across production lines. For application-specific recommendations or to secure the PSSN toolholder from Teknik Makina for your workshop, contact Metav Werkzeuge for tailored advice and reliable supply from Emmerich. Technical data Article number: P181TM Manufacturer: Teknik Makina Shank width: 20 mm Head width: 25 mm Holder height: 20 mm Cutting height: 30 mm Overall length: 125 mm Weight: 0.416 kg Cutting angle: 45° ISO designation: PSSNL 2020 For indexable inserts: SNMG 1204 Mounting bore: K12 Cutting direction: left-hand FAQ What inserts fit this holder? The PSSN clamping holder is specified for SNMG 1204 indexable inserts and secures them via the K12 mounting interface. Is this a left-hand or right-hand toolholder? This toolholder is supplied in a left-hand orientation; it is intended for left-hand turning operations on suitable lathes. What is the ISO designation and why is it relevant? The ISO designation PSSNL 2020 identifies the holder geometry and interface, ensuring compatibility with standardised toolposts and spare parts. Will the holder fit compact toolposts? Yes; the 20 mm shank and 125 mm overall length provide a compact footprint that integrates easily with most workshop toolpost arrangements. How does the 45° cutting angle benefit machining? A 45° cutting geometry promotes steady chip flow and more uniform cutting forces, which can improve insert life and surface finish. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of a robust left‑hand turning solution that combines precise insert clamping with a compact 150 mm overall length for tight setups; its PSSNL 2525 geometry and 25 mm clamp height ensure repeatable seating of SNMG 1204 inserts — order the clamping holder directly via Metav Werkzeuge or ask our consultants if needed PSSN for SNMG Indexable Inserts (PSSNL 2525) – Left‑hand clamping holder by Teknik Cutting Tools The PSSN for SNMG Indexable Inserts is a left‑hand clamping holder designed for turning applications that require secure seating of SNMG 1204 inserts in confined toolpost arrangements. Left‑hand orientation for reverse turning Secure seating for SNMG 1204 inserts Compact overall length of 150 mm 25 mm clamp height for stable support Consistent insert clamping for reliable turning results The toolholder is engineered to deliver repeatable clamping so that insert seating remains consistent from part to part. With a 25 mm clamp height and a dedicated pocket for SNMG 1204 inserts, the design reduces micro‑movement during cut entry and exit. A precise clamping interface minimises vibration and contributes to improved surface finish and tool life. The 45° cutting angle is optimised for general turning operations, balancing chip flow and machining forces to support steady material removal. Efficient left‑hand configuration for specific workflow needs Built as a left‑hand solution, this holder suits reversing operations and setups where the cutting direction must be mirrored. The left‑hand orientation and the compact 150 mm overall length enable insertion into constrained tool posts and turret stations without compromising accessibility. The 32 mm cutting head width and 30 mm cutting height are chosen to maintain appropriate overhang and rigidity, which supports higher feed rates and consistent part tolerances in production environments. Compatibility that simplifies tooling management Compatibility with standard SNMG 1204 indexable inserts means fewer special items in inventory and easier tool changes on the shop floor. The holder accepts a common M12 mounting interface for secure attachment and weighs approximately 0.742 kg, offering a balance between robustness and manageable handling during tool changes. This pragmatic matching of holder geometry to insert format reduces setup time and supports predictable machining performance across batches. Practical design for workshop ergonomics and maintenance The holder’s geometry — referenced as PSSNL 2525 in ISO designation — focuses on straightforward maintenance and minimal adjustment. A clear clamp profile speeds insert replacement, while the resilient mechanical interface keeps retightening needs low. The combination of compact dimensions and stable clamping helps to lower the likelihood of rework and supports continuous production runs with fewer interruptions, an advantage for both craft workshops and small production cells. For reliable left‑hand turning with Teknik Cutting Tools’ PSSNL 2525 clamping holder, contact Metav Werkzeuge in Emmerich for purchase and personalised technical advice: info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: P182TM Model (ISO): PSSNL 2525 Product: PSSN for SNMG Indexable Inserts Brand: Teknik Makina Facts Clamp height: 25 mm Cutting head width: 32 mm Cutting height: 30 mm Overall length: 150 mm Weight: 0.742 kg Cutting angle: 45° Mounting thread: M12 Special features Left‑hand cutting direction Suitable for SNMG 1204 inserts Compact toolholder for tight setups Secure clamping geometry for repeatability FAQ What insert grade and size fit this holder? The PSSN for SNMG Indexable Inserts is designed for SNMG 1204 format inserts; matching insert grades should be chosen according to material and cutting conditions. Is the holder suitable for reverse turning operations? Yes, the left‑hand orientation of this clamping holder makes it suitable for reverse or left‑hand turning tasks. What are the key dimensions to check for turret compatibility? Check the 25 mm clamp height, 150 mm overall length, and the 32 mm cutting head width to ensure compatibility with the turret or toolpost. How does the clamp geometry affect surface finish? The secure clamping and precise seating of SNMG inserts reduce micro‑movement and vibration, which helps to improve surface finish and repeatability. Can standard M12 mounting be used on most toolposts? The holder uses an M12 mounting interface for attachment; compatibility depends on the toolpost or adapter design. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com

Take advantage of a compact, ISO-defined clamp holder that combines a 45° cutting angle with compatibility for SNMG 1204 inserts to improve turning accuracy and cycle-time stability. For purchase or technical advice, order via Metav Werkzeuge or consult our product specialists. PSSN for SNMG Indexable Inserts — PSSNR 1616 clamp holder with 45° cutting angle (Teknik Makina) PSSN for SNMG Indexable Inserts is a right-hand clamp holder designed for SNMG 1204 turning inserts, delivering controlled chip flow and secure clamping in medium-duty turning operations. 45° cutting angle for precise turning Compatible with SNMG 1204 inserts ISO PSSNR 1616 shank, 16 x 16 mm 100 mm overall length, 0.218 kg weight Improved cutting stability and surface finish with a 45° geometry The 45° geometry of this clamp holder provides a balanced combination of radial and axial force components that lead to consistent chip control and a finer surface finish on turned parts. Designed for SNMG 1204 inserts, the toolholder aligns the insert pocket for optimal shear and minimised vibration, which reduces rework and increases first-pass yield. With a cutting height of 30 mm and a cutting head width of 20 mm, the construction supports stable engagement depths while preserving insert life. Where cycle-time efficiency and repeatable results are priorities, this configuration delivers measurable gains in productivity. Quick set-up and secure clamping for repeatable machining The holder meets the ISO designation PSSNR 1616, featuring a compact 16 mm shank height and width that make it easy to fit common toolposts and turrets. Compatibility with the H12 boring-bar designation streamlines replacement and stock management. At 0.218 kg, the balanced mass minimises centrifugal effects at speed and helps maintain tool geometry under load. The secure clamping system and standardised interface reduce set-up time and make insert indexing straightforward, translating into lower downtime and predictable process performance. Integration into the workshop and reliable daily use Built for routine shop-floor demands, the right-hand orientation and 100 mm overall length support common turning tasks while keeping overhang moderate for rigidity. The holder’s robust design ensures dependable behaviour across batch and single-part work, enabling confident selection for production or maintenance cycles. For operations aiming to harmonise tooling across machines, the combination of ISO conformity and SNMG 1204 compatibility simplifies logistics and training. The toolholder is a practical choice where durability and straightforward integration are valued. For a tailored recommendation on integrating this Teknik Cutting Tools clamp holder into existing tool chains, contact Metav Werkzeuge in Emmerich at info@metav-werkzeuge.com or by phone on +49 2822 7131930 for expert guidance and fast supply. Technical data Article number: P170TM Manufacturer: Teknik Makina Product designation: PSSN for SNMG Indexable Inserts Facts Cutting angle: 45° Shank height: 16 mm Shank width: 16 mm Cutting head width: 20 mm Cutting height: 30 mm Overall length: 100 mm Weight: 0.218 kg Cutting direction: right Compatible inserts: SNMG 1204 Special features ISO designation: PSSNR 1616 Boring-bar designation: H12 Right-hand orientation For SNMG 1204 indexable inserts FAQ Which inserts fit this clamp holder? The holder is designed for SNMG 1204 indexable inserts; insert geometry must match the SNMG 1204 specification for correct seating and clamping. What is the ISO designation and shank size? The tool is specified as ISO PSSNR 1616 with a 16 x 16 mm shank, suitable for standard toolposts accepting that format. Is the holder for right- or left-hand turning? This clamp holder is configured for right-hand cutting direction, optimised for standard right-hand turning operations. What are the key dimensions that affect rigidity? Key dimensions are the 100 mm overall length, 16 mm shank, 20 mm cutting head width and a 30 mm cutting height, which together determine overhang and stiffness. Can this holder reduce set-up time in production cells? The ISO interface (PSSNR 1616) and H12 boring-bar designation simplify mounting and replacement, helping to reduce set-up time and improve repeatability. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of a compact right‑hand toolholder that delivers secure clamping for SNMG inserts, a practical 45° cutting angle and straightforward M12 mounting — all designed to keep turning operations efficient and repeatable. Order directly via Metav Werkzeuge or consult our team for application advice. Teknik Makina PSSN for SNMG Indexable Inserts — right‑hand turning holder with 45° angle PSSN for SNMG Indexable Inserts is a right‑hand turning toolholder engineered for secure clamping of SNMG 1204 inserts in general workshop and industrial turning applications. Secure clamping for SNMG 1204 inserts 45° cutting angle for versatile turning ISO PSSNR 2525 for standardised fitment M12 mounting thread for common toolposts Improved process stability for consistent turning results The PSSN style holder is designed to increase rigidity at the cutting zone and reduce vibration during interrupted or continuous cuts. Its 45° cutting angle helps to distribute cutting forces more evenly across the insert, which often results in smoother surface finishes and prolonged insert life. For operations that demand repeatable outcomes, this type of clamping brings measurable benefits in cycle stability and tool life, helping to lower overall production costs through fewer change‑overs and less scrap. Fast, reliable set‑up and standardised compatibility With an M12 mounting thread and the ISO designation PSSNR 2525, the toolholder fits common toolpost systems and aligns with industry standards to simplify tooling logistics. The combination of a 30 mm cutting height and 150 mm overall length provides a predictable tool geometry that makes set‑up quicker and tool offsets easier to manage. The holder’s dimensions and ISO conformity reduce the need for bespoke adaptors, shortening preparation times and enabling faster changeovers at the machine. Practical shop‑floor advantages and suitability Engineered for use with SNMG 1204 indexable inserts, the holder offers a compact footprint with a 0.742 kg mass that balances stiffness with manageable handling during tool changes. The right‑hand orientation makes it suitable for standard right‑hand turning tasks; compatibility with SNMG inserts keeps inventory lean because commonly used insert grades cover a wide range of materials and cutting conditions. Sourcing through Metav ensures dependable availability and professional product support for industrial and craft environments. Speak with Metav Werkzeuge to align the Teknik Cutting Tools PSSN holder with specific turning processes and check stock or delivery options via info@metav-werkzeuge.com or +49 2822 7131930 Technical data Article number: P172TM Manufacturer: Teknik Makina Core dimensions Overall length: 150 mm Cutting height: 30 mm Holder height: 25 mm Head width: 32 mm Holder width: 25 mm Weight: 0.742 kg Cutting angle: 45° Cutting direction: right Features & compatibility ISO designation: PSSNR 2525 Mounting thread: M12 Suitable for: SNMG 1204 indexable inserts Orientation: right‑hand FAQ Which inserts fit this holder? The holder is designed for SNMG 1204 indexable inserts and accepts standard SNMG geometries for turning applications. Is the PSSN holder suitable for heavy cuts? The PSSN for SNMG indexable inserts offers enhanced rigidity and a 45° geometry that is suitable for many medium to heavy turning tasks when matched with the correct insert grade. What does the ISO designation PSSNR 2525 mean? PSSNR 2525 denotes the holder style and square shank dimensions according to common ISO conventions, ensuring interchangeability with compatible toolposts. Can this holder be used for left‑hand turning? This specific version is a right‑hand orientation; left‑hand operations require the corresponding left‑hand variant. How does the 45° cutting angle affect tool life? A 45° approach angle spreads cutting forces across the insert, which can reduce edge loading and improve insert life and surface finish when cutting parameters are optimised. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com