Gibt es einen Hahn und Kolb Online Shop?

Take advantage of a rigid clamping solution with a compact 20 mm shank and a precise 4 mm cutting width that accepts Korloy 4C MGM inserts; the combination reduces deflection and streamlines set-up. Order the parting clamp holder K610TM directly via Metav Werkzeuge or ask our consultants if needed. Parting clamp holder K610TM — compact parting/grooving tool holder with 20 mm shank and 4 mm cutting width (Teknik Makina) Parting clamp holder K610TM is a dedicated tool holder for controlled parting and grooving operations that suits production and workshop turning applications Compact 20 mm shank for confined toolposts Precise 4 mm cutting width for accurate parting Compatible with Korloy 4C MGM indexable inserts 180 mm overall length for extended reach without excess overhang Improved process consistency through rigid clamping The K610TM is engineered to reduce tool deflection by prioritising a stiff clamping interface and a compact profile. With a 20 mm shank and a short, controlled overhang, the holder stabilises the cutting point so that the insert geometry can deliver repeatable parting results. In practice, reduced deflection means fewer rejects and less rework; this is particularly relevant where tight diametral tolerances are required. The holder’s compatibility with Korloy 4C MGM inserts ensures a predictable cutting edge and quick insert indexing, supporting continuous operation in medium-volume turning cells. Fewer set‑ups and faster index changes The clamping system is designed for straightforward insert replacement and secure retention. Accepting 4C MGM inserts and featuring the shank designation S20Q 4C‑R / MGM, the holder simplifies changeovers and aligns with common insert geometries from Korloy. For workshops aiming to shorten machining downtime, this results in faster tool swaps and consistent alignment of the cutting edge. The measured cutting height of 35 mm and nominal cutting width of 4 mm provide defined engagement parameters for predictable chip control during parting operations. Compact build for machine compatibility and reach A total length of 180 mm combined with a body diameter of 26 mm gives the holder adequate extension while limiting vibration. The overall mass of 0.443 kg contributes to balance on the turret, aiding stable rotation at typical lathe speeds. The compact dimensions make the tool holder suitable for tight turret pockets and multi‑station turrets where space is at a premium. When used as part of a standard turning set-up, the holder delivers controlled cutting performance without requiring larger toolposts or special fixtures. Contact Metav Werkzeuge to specify the Teknik Makina K610TM for current turning cells and to arrange detailed technical advice via info@metav-werkzeuge.com or by phone on +49 2822 7131930 Technical data Article number: K610TM Designation: Parting clamp holder Manufacturer: Teknik Makina Compatible inserts: 4C MGM (Korloy) Dimensions & weight Shank diameter: 20 mm Cutting height: 35 mm Cutting width: 4 mm Overall length: 180 mm Body diameter: 26 mm Weight: 0.443 kg Compatibility & features Shank designation: S20Q 4C‑R Clamping type: MGM Suitable insert family: 4C MGM Brand compatibility: Korloy FAQ What insert types fit the K610TM? The K610TM accepts 4C MGM indexable inserts; Korloy 4C MGM inserts are directly compatible. What shank size is required for mounting? Mounting requires a 20 mm shank holder pocket or compatible toolpost that accepts a 20 mm shank diameter. Is the holder suitable for high-feed parting operations? The holder’s rigid design and controlled overhang support stable parting at typical lathe feeds; select insert geometry matched to the material and feed for best results. How long is the K610TM and what clearance does it give? The total length is 180 mm, providing reach for deeper grooves while keeping overhang limited to reduce vibration. Which brand manufactures the tool holder? The tool holder is supplied by Teknik Makina and sold via Metav Werkzeuge under SKU K610TM Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Benefit from a rigid 20 mm shank, a 40 mm cutting height and a compact 180 mm overall length to achieve repeatable parting and grooving results; order the parting tool holder directly via Metav Werkzeuge or consult our specialists for application-specific guidance. Parting tool holder K652TM – 20 mm shank, 40 mm cutting height by Teknik Makina A parting tool holder engineered for secure clamping of 4C indexable inserts, optimised for parting and grooving tasks in general workshop and light industrial turning operations. 20 mm shank diameter for high rigidity 40 mm cutting height for standard inserts Compatible with 4C indexable inserts 180 mm overall length for versatile reach Stiffness and stability for precise parting The holder combines a 20 mm shank diameter with a compact mass of 0.44 kg, delivering the rigidity required for clean parting cuts and reduced vibration. Increased stiffness directly improves surface finish and tool life by maintaining stable cutting geometry under load. For machinists seeking consistent cycle-time and reduced rework, this holder offers a reliable mechanical basis that supports repeatable quality in batch and single-piece production. Compatibility that speeds up set-up Designed for indexable tooling, the clamp accepts 4C inserts and features a cutting width of 4 mm and a 40 mm cutting height, matching common insert standards. The holder works with the S20Q shank format and the clamping designation 4C‑R S224, enabling quick insert changes and straightforward tool reconditioning. Clear, standardised interfaces mean fewer special adapters and faster changeovers at the toolpost. Practical dimensions for workshop use With an overall length of 180 mm and a head diameter of 26 mm, the toolholder balances reach and clearance for a broad range of turning operations. These dimensions support operations on small to medium lathes where controlled overhang is critical; shorter overhang reduces deflection, while the measured length allows access to deeper workpiece profiles. The low profile is particularly helpful where turret indexing and adjacent tooling create tight spacing. Designed for everyday productivity Fitted to accept standard clamping bars and indexable inserts, the holder reduces tooling complexity on the shop floor and keeps maintenance straightforward. The combination of standard formats, modest weight and uncomplicated geometry reduces set-up time and simplifies inventory management. For teams aiming to streamline production, this holder contributes to a dependable toolset that supports efficient machining with minimal specialisation. Contact Metav Werkzeuge for tailored advice on the Teknik Cutting Tools parting tool holder K652TM and how it integrates into existing turning setups; Metav Werkzeuge is available in Emmerich at info@metav-werkzeuge.com or +49 2822 7131930 Technical data Article number: K652TM Manufacturer: Teknik Makina eClass: 21181005 Files: 2 attachments Facts Shank diameter: 20 mm Cutting height: 40 mm Cutting width: 4 mm Overall length: 180 mm Diameter: 26 mm Weight: 0.44 kg Indexable insert type: 4C Special features Accepts S20Q shank format Compatible with 4C‑R S224 Designed for parting and grooving applications FAQ What type of inserts fit this holder? The parting tool holder accepts 4C indexable inserts and is prepared for standard parting widths such as 4 mm. Which shank formats are compatible? Compatibility includes the S20Q shank format and the clamping designation 4C‑R S224, enabling use with commonly available clamping bars. Is the holder suitable for heavy interrupted cuts? The holder’s 20 mm shank and compact geometry provide good rigidity for routine parting; for heavy interrupted cuts, consider application-specific assessment. How long is the toolholder and how does that affect use? The overall length is 180 mm, offering a balance between reach and reduced overhang to limit deflection during turning operations. What is the weight and why does it matter? Weighing 0.44 kg, the holder offers a low mass for ease of handling while retaining sufficient stiffness for accurate parting and grooving tasks. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of precise clamping, straightforward integration and robust reach to keep grooving cycles predictable; order the parting and grooving clamping holder directly via Metav Werkzeuge or consult our specialists for application advice. Teknik Makina Parting and Grooving Clamping Holder K677TM — 25 mm shank, 4 mm cutting width Teknik Makina Parting and Grooving Clamping Holder K677TM is a purpose‑built clamping tool for parting and grooving operations in turning machines, offering a rigid 25 mm shank and a narrow 4 mm cut for accurate, repeatable results Robust 25 mm shank for stable toolholding Compatible with 4C indexable inserts (ISCAR-compatible) 4 mm cutting width for fine grooving control 200 mm overall length for extended reach Reduced cycle times through controlled cutting dynamics The holder is engineered to improve process efficiency by combining a 25 mm shank with a compact cutting geometry. The slender 4 mm cutting width and 40 mm cutting-edge height reduce cutting forces during parting and narrow‑groove turning, which in turn lowers vibration and improves surface finish. These mechanical benefits support shorter machining cycles and more consistent batch quality, helping production lines run with fewer interruptions and less rework. Fast setup and seamless integration into existing toolchains Designed for compatibility, the clamping system accepts 4C indexable inserts and is ISCAR-compatible, simplifying inventory and substitute options. The shank interface labels S25R and 4C-R DGN indicate standardised mounting dimensions for straightforward insertion into common tool posts and holders. Reduced setup complexity translates into less downtime at changeover and a more efficient toolroom logistics flow, especially where mixed‑brand insert stocks are used. Predictable rigidity and reach for repeatable results With a 200 mm overall length and a 31 mm diameter at the tool body, the holder delivers the reach required for deeper set‑ups while maintaining rigidity that keeps cuts stable. The relatively light mass of 0.802 kg promotes easier handling during tool changes without compromising balance on the lathe. These dimensional characteristics combine to provide predictable cutting behaviour across repetitive runs, benefitting shops that prioritise consistent tolerances and surface quality. For reliable parting and grooving performance choose the Teknik Makina holder K677TM — contact Metav Werkzeuge for stock information and technical guidance via info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: K677TM Manufacturer: Teknik Makina Brand SKU: K677TM Facts Shank diameter: 25 mm Cutting width: 4 mm Cutting-edge height: 40 mm Overall length: 200 mm Diameter: 31 mm Weight: 0.802 kg Special features Fits 4C indexable inserts ISCAR-compatible Shank designation: S25R Holder shank type: 4C-R DGN FAQ Which insert type fits this holder? The holder accepts 4C indexable inserts and is specified as ISCAR-compatible, allowing use of standard 4C parts in the Teknik Makina K677TM clamping system. What shank and mounting designations apply for mounting? Mounting follows the S25R shank designation and the 4C-R DGN holder interface, ensuring compatibility with common turning tool posts that accept these standards. Is the holder suitable for deep grooves or long reach work? The 200 mm overall length provides extended reach for deeper set‑ups while the 31 mm diameter preserves rigidity for controlled cutting in parting and grooving tasks. How does the holder affect vibration and surface finish? The combination of a 25 mm shank, compact cutting width and balanced mass (0.802 kg) reduces vibration during narrow cuts, improving surface finish and repeatability when used under appropriate machining conditions. Can the Teknik Makina K677TM be used with inserts from different manufacturers? Yes — the K677TM is designed to be ISCAR-compatible and accepts common 4C indexable inserts, which facilitates cross-brand use and simplifies tooling inventories. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of the combination of rigid 32 mm shank stability, compatibility with ZCC 4C ZT.D inserts, and a compact 4 mm cutting width for precise parting operations; order the parting clamp holder directly via Metav Werkzeuge or ask our consultants if needed. Parting Clamp Holder K685TM – 32 mm shank, 4 mm cutting width (Teknik Makina) A Parting Clamp Holder K685TM engineered for secure clamping of ZCC 4C ZT.D inserts, intended for turning and grooving operations in general workshop and light industrial environments. 32 mm shank diameter Compatible with 4C ZT.D inserts (ZCC) 4 mm cutting width Improved rigidity for consistent parting results The holder’s 32 mm shank diameter provides a stiff, vibration-resistant connection to the toolpost, which reduces chatter and supports repeatable parting cycles. This structural stability leads to more consistent surface finish and fewer rejected parts when machining narrow grooves. The relatively compact total length of 250 mm balances accessibility and rigidity, making the tool suitable for standard lathes where tool overhang is a limiting factor. Secure insert clamping and easy insert choice Designed to accept 4C ZT.D insert styles from ZCC, the clamp secures the insert reliably while preserving cutting edge geometry. The 4 mm cutting width allows narrow parting cuts without excessive material waste, and the 50 mm cutting height ensures sufficient contact area for larger inserts or extended engagement when required. The ISO shank designation S32S ensures compatibility with common toolposts and adapters, simplifying integration into existing tool setups. Practical benefits for workshop throughput With a robust clamping mechanism and a straightforward interface to established insert types, the tool holder supports faster set-ups and predictable tool life. The reduced need for frequent re-clamping and the compatibility with off-the-shelf inserts decrease downtime and inventory complexity. The unit’s 1.645 kg mass contributes to stability during heavy-engagement cycles while remaining manageable for manual handling during changeover. Typical applications and material considerations This parting clamp holder is suited to conventional turning, grooving and parting-off tasks on non-complex geometries. Its design addresses general-purpose steel and alloy turning where a narrow kerf and secure insert retention are required. For specialised material classes or hardened workpieces, select cutting grades and feeds appropriate to the insert manufacturer’s recommendations to achieve optimal results. For supply and technical advice on the Teknik Makina K685TM, contact Metav Werkzeuge in Emmerich for precise ordering, availability and delivery coordination: info@metav-werkzeuge.com | +49 2822 7131930 Technical data SKU: K685TM Manufacturer: Teknik Makina Brand: Teknik Makina Core specifications Shank diameter: 32 mm Cutting height: 50 mm Cutting width: 4 mm Total length: 250 mm Diameter: 39 Weight: 1.645 kg Compatibility & features Compatible with: 4C ZT.D inserts (ZCC) Insert designation: 4C ZT.D Shank designation ISO: S32S Clamping bar designation: 4C-R ZT.D FAQ What shank size does this holder use? The Parting Clamp Holder K685TM uses a 32 mm shank (ISO S32S), providing enhanced rigidity for stable parting operations. Which inserts fit this holder? This clamping tool accepts 4C ZT.D style inserts and is specified as compatible with ZCC insert types for straightforward replacement and selection. What is the maximum cutting height accommodated? The holder supports a cutting height of 50 mm, allowing the use of inserts with larger engagement areas when required. Is the tool suitable for long overhangs? With a total length of 250 mm and a robust 32 mm shank, the holder is balanced for standard lathe set-ups; excessive overhang is not recommended as it may reduce rigidity and affect finish quality. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of the compact design and secure clamping to achieve reliable parting operations: the combination of a 20 mm clamping height and a 4 mm cutting width delivers stable insert seating and narrow, accurate cuts; order directly via Metav Werkzeuge or contact the technical team for integration advice. Parting clamp holder D775TM — Right‑hand parting and grooving toolholder (Teknik Makina) The Parting clamp holder D775TM is a right‑hand toolholder engineered for parting‑off and grooving on CNC lathes, compatible with standard 4C DGN indexable inserts and intended for straightforward integration into conventional toolposts. 20 mm clamping height for stable insert retention 4 mm cutting width for narrow parting operations Compatible with 4C DGN indexable inserts (ISCAR) Right‑hand cutting for standard lathe setups Stable clamping for reduced vibration and predictable results The D775TM offers a 20 mm clamping height that secures the insert firmly in the pocket, which reduces tool chatter and helps maintain a consistent cutting geometry. This stable seating translates into longer insert life and fewer re‑set cycles on the lathe, improving process reliability in both single‑piece flow and short‑run production. Clear clamping forces and compact tool mass limit deflection during plunge cuts, making parting results more predictable and reducing scrap rates. Standardised insert compatibility speeds up changeovers Designed around the ISO size 2020 insert pocket, this holder accepts 4C DGN indexable inserts and is compatible with ISCAR standard parts, enabling rapid replacements from commonly stocked inserts. The standard interface supports quick changeovers and easier inventory management, which shortens downtime between jobs and keeps the machining cell productive. The right‑hand orientation matches typical lathe set‑ups for parting and light grooving operations. Compact footprint for flexible toolpost mounting With an overall length of 125 mm and a cutting head width of 20 mm, the holder fits well into tight toolpost arrangements and reduces overhang compared with longer toolholders. The compact dimensions help to improve access to narrow bore entries and enable closer tool spacing on multi‑tool turrets. At approximately 0.391 kg, the low mass further minimises centrifugal loads on the turret while maintaining the rigidity required for controlled parting operations. Purposeful design for workshop productivity The clamp‑style retention and narrow 4 mm cutting width make the holder particularly suited to precision parting and finishing cuts where material loss must be minimised. The right‑hand cutting direction and robust tool geometry support consistent chip control and surface finish, while compatibility with widely available inserts simplifies procurement. For workshops seeking a reliable parting solution that integrates with common tooling standards, this holder balances practicality and performance without unnecessary complexity. Discuss installation options and compatibility with Metav Werkzeuge’s technical advisors by phone or email — Metav’s Emmerich team can confirm fitment with existing toolposts and ISCAR inserts and arrange prompt delivery from stock Technical Data Article number: D775TM Manufacturer: Teknik Makina Designation: Parting clamp holder D775TM SKU: D775TM Dimensions & key measurements Clamping height: 20 mm Cutting head width: 20 mm Body width: 20 mm Cutting width: 4 mm Max plunge depth: 20 mm Overall length: 125 mm Weight: 0.391 kg Compatibility & features Fits inserts: 4C DGN Compatible insert manufacturer: ISCAR ISO designation: 2020 Cutting direction: right Holder function: parting and grooving clamp holder FAQ Which inserts are compatible with this holder? The D775TM accepts 4C DGN indexable inserts in ISO 2020 size and is suitable for ISCAR‑type inserts designed for parting and grooving. Is the holder right‑ or left‑hand cutting? This holder is manufactured for right‑hand cutting operations and is intended for standard lathe toolpost arrangements. What are the key dimensions to check for my toolpost? Key dimensions to verify are the 20 mm clamping height, 4 mm cutting width, 20 mm cutting head width and the 125 mm overall length; the holder weighs approximately 0.391 kg. Which machines and applications suit this holder? The parting clamp holder is intended for CNC lathes and turret lathes for parting‑off, narrow grooving and finishing operations in jobbing and light production environments. How does the design help extend insert life? Secure clamp retention and a compact, low‑deflection body reduce vibration and movement during cuts, which supports longer insert life and more consistent surface finishes with fewer interruptions. Manufacturer / Responsible: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com

Benefit from a robust combination of 25 mm shank stability, a 2 mm cutting width and a 50 mm cutting height for precise, repeatable parting operations; order the parting toolholder directly via Metav Werkzeuge or consult their advisors for application-specific guidance. Parting toolholder K644TM – compact parting/clamping holder with 25 mm shank and 2 mm cut width (Teknik Makina) Parting toolholder K644TM provides a compact clamping solution for parting and grooving tasks on conventional lathes, designed to accept 2C indexable inserts and for use with S25R shank tooling. Stable 25 mm shank for secure mounting Narrow 2 mm cutting width for fine parting 50 mm cutting height for deeper operations Compatible with 2C indexable inserts Consistent, measurable stability for repeatable parting The holder is engineered for dimensional stability: the 25 mm shank and solid body mass deliver reduced vibration and improved concentricity during parting operations, which translates into fewer rejects and less rework. With a modest weight of 0.763 kg, the toolholder combines rigidity with manageable handling for setup. The result is a predictable machining process where cycle times and tolerances remain reliable under production conditions. Fine-width cutting for precise separation and surface quality A 2 mm cutting width permits close-control parting and narrow-groove applications where material loss must be minimised and component geometry preserved. Matched with the 2C insert format, chip evacuation and insert life are optimised for interrupted cuts typical of parting tasks. The moderate cutting height of 50 mm allows engagement depths that suit many common workpieces without excessive overhang, supporting cleaner break-off faces and less secondary finishing. Straightforward integration with standard lathe tooling The toolholder accepts bars to the S25R shank designation and presents an overall length of 200 mm with an outer diameter of 34 mm, allowing easy mounting in typical toolposts and holders. Compatibility with the common bar standard reduces retrofit time and supports toolset standardisation across a shop floor. Engineers benefit from a component that fits established setups rather than requiring bespoke fixtures. Practical workshop benefits and supply reliability Compact design and clear specification make inventory management and tool selection more efficient. The holder’s combination of defined dimensions, recognised insert format and standard shank specification supports predictable procurement and quicker tool changeovers. For buyers seeking dependable delivery and a quality filter for European supply, the product is offered through Metav Werkzeuge’s distribution network, which emphasises consistent availability and technical transparency. Contact Metav Werkzeuge for tailored advice on the Teknik Makina parting toolholder K644TM and to arrange supply directly from Emmerich. Technical Data Article number: K644TM Manufacturer: Teknik Makina Facts Shank diameter: 25 mm Cutting height: 50 mm Cutting width: 2 mm Overall length: 200 mm Outer diameter: 34 mm Weight: 0.763 kg Special features Insert format: 2C Bar designation: S25R Application type: parting/clamping FAQ Which insert format is required for this holder? The parting toolholder K644TM by Teknik Makina is designed for 2C indexable inserts, matching the holder's clamping geometry for secure seating and reliable cutting performance. What are the key dimensions required for machine compatibility? Key dimensions for the Teknik Makina parting toolholder K644TM are a 25 mm shank diameter, 200 mm overall length, and 34 mm outer diameter, which support installation in standard toolposts that accept S25R‑shank tooling. Is the holder suitable for deeper parting operations? Yes — with a 50 mm cutting height the K644TM supports deeper engagements than many compact parting holders, allowing production of parts that require increased cut depth while maintaining stability. How does the cutting width influence the machining result? The 2 mm cutting width of the Teknik Makina toolholder K644TM reduces material removal per pass, delivering narrower kerfs, improved material utilisation and finer parting finishes for precision components. Can this holder be managed easily in a small workshop environment? The compact dimensions and moderate weight (0.763 kg) of the K644TM make it practical for workshops seeking dependable parting performance without complex handling procedures. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of a compact, right-hand parting solution that combines a 5 mm effective cutting width with a 20 mm cutting head for steady cuts and reduced vibration; the 170 mm overall length keeps setups compact while offering a maximum plunge depth of 25 mm for reliable parting. Order the parting toolholder directly via Metav Werkzeuge or ask our consultants if needed. Teknik Makina parting clamp holder D680TM — Right-hand parting toolholder, 5 mm cutting width The Teknik Makina parting clamp holder D680TM is a right-hand parting and grooving toolholder designed for lathe operations and compatible with Korloy indexable inserts in the 5C MGM format Parting toolholder D680TM by Teknik Makina Right-hand cutting direction for lathe use 5 mm effective cutting width 20 mm cutting head width for stability Compatible with Korloy 5C MGM inserts Stable parting for consistent cycle times The holder offers a 5 mm effective cutting width paired with a 20 mm cutting head, delivering a stable support plane that reduces chatter and improves surface finish. This construction helps to maintain consistent tool engagement, which in turn lowers scrap rates and shortens cycle times in serial machining. The right-hand configuration ensures straightforward integration into standard lathe toolposts and is particularly suited to repeatable cut-off operations. Fast set-up and proven compatibility Built to the ISO 2020 shank standard with the shank designation 5C-R MGM, this clamp-style holder accepts 5C MGM indexable inserts from Korloy, enabling quick insert changes and repeatable clamping accuracy. The design reduces clamping time during tool changes, so set-up routines are streamlined. The toolholder’s modest mass of 0.391 kg contributes to a balanced assembly that is easy to handle while remaining rigid in the cut. Practical use across turning and grooving tasks With an overall length of 170 mm and a maximum plunge or groove depth of 25 mm, the toolholder is suitable for medium-depth parting and grooving on production and jobbing lathes. The compact dimensions make it practical where turret clearance is limited, while the secure clamping mechanism supports controlled chip evacuation and repeatable parting. The component is optimised for machining workflows that prioritise reliability and predictable results. Quality and workshop assurance Manufactured for industrial use, the holder combines a robust clamping solution with compatibility to established insert formats to deliver dependable performance over many cycles. When paired with the correct Korloy inserts, the assembly achieves improved tool life and steady machining behaviour. As part of a centrally supplied range, the product benefits from Metav’s quality filtering and logistics, ensuring reliable delivery to the workshop. For reliable parting performance and compatibility advice on the Teknik Makina D680TM, contact Metav Werkzeuge for ordering and technical consultation at +49 2822 7131930 or info@metav-werkzeuge.com Technical data Article number: D680TM Manufacturer: Teknik Makina Facts Overall length: 170 mm Weight: 0.391 kg Effective cutting width: 5 mm Cutting head width: 20 mm Maximum plunge depth: 25 mm Special features Cutting direction: right Compatible inserts: 5C MGM (Korloy) Holder ISO designation: 2020 Shank designation: 5C-R MGM FAQ What insert type fits this holder? The parting clamp holder D680TM is compatible with 5C MGM indexable inserts and is commonly used with Korloy inserts in that format. Is the holder suitable for deep parting operations? The toolholder provides a maximum plunge depth of 25 mm; deeper cuts would require a different holder or a specific insert strategy. Which way does the cutting action run? This model is configured for right-hand cutting direction, suitable for standard lathe setups with right-hand tool orientation. What are the shank and mounting designations? The holder follows an ISO 2020 shank designation and is identified with the shank code 5C-R MGM for mounting compatibility. How compact is the toolholder for turret clearance? With an overall length of 170 mm and a compact head width, the assembly is designed for restricted turret spaces while maintaining rigidity. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of a combination of secure clamping and precise right-hand grooving for consistent shop production; the holder’s 25 mm head width and 5 mm cutting width ensure repeatable results while the robust design supports up to 40 mm plunge depth — order directly via Metav Werkzeuge or consult the team for application advice. Teknik Makina Grooving Clamp Holder — right-hand, 25 mm head The Teknik Makina Grooving Clamp Holder is a right-hand, ISO 2525 toolholder designed for controlled parting and grooving with 5C MGM inserts in turning operations. Right-hand cutting direction 25 mm head width for stable support 5 mm cutting width for narrow grooves Compatible with Korloy 5C MGM inserts Reliable clamping that improves process stability Built for precision turning and grooving, this toolholder delivers stable clamping with a compact footprint. The concept focuses on minimising vibration and deflection so that tool life and surface finish are improved; the ISO 2525 designation and solid construction mean insert seating and repeatability are consistent across batches. By using a holder with a defined head width of 25 mm, set-up variance is reduced and machine cycle times benefit from fewer reworks and adjustments. Flexible compatibility for workshop integration Installation is simplified by the compatibility with common insert systems: the holder accepts 5C MGM inserts and is matched to bore bar type 4C-R MGM, making it straightforward to integrate into existing tooling banks. The right-hand cutting direction suits standard lathe configurations and allows programming and toolpath planning to be kept consistent. Where grooves or parting tasks require a narrow kerf, the 5 mm cutting width provides a controlled cut that is especially useful for material-saving operations and close-tolerance components. Designed for durable, efficient machining With a total length of 170 mm and a service weight of 0.745 kg, the holder balances reach and rigidity for routine turning tasks. The design supports a maximum plunge depth of 40 mm, which enables deeper grooving without compromising clamping integrity. Components are machined and finished to ensure a secure interface with the insert and the shank; as a consequence, downtime for tool change is reduced and throughput is improved. The overall specification is aimed at workshops seeking a dependable, production-ready grooving solution. For fast procurement or to discuss right-hand grooving applications with Metav Werkzeuge — contact Metav Werkzeuge GmbH at info@metav-werkzeuge.com or call +49 2822 7131930 for tailored advice and order support Technical data Article number: D964TM Manufacturer: Teknik Makina Facts Head width: 25 mm Cutting width: 5 mm Maximum plunge depth: 40 mm Overall length: 170 mm Weight: 0.745 kg Compatibility & special features ISO designation: 2525 Fits inserts: 5C MGM Compatible with inserts by: Korloy Bore bar designation: 4C-R MGM Cutting direction: right FAQ What insert types are compatible with this grooving holder? The Teknik Makina grooving clamp holder (SKU D964TM) is designed for 5C MGM inserts and is Korloy-compatible for straightforward toolpool integration. What is the maximum plunge depth allowed with this holder? The holder permits a maximum plunge depth of 40 mm, enabling deeper grooving operations while preserving clamping stability. Which cutting direction is this holder intended for? This toolholder is specified for right-hand cutting, matching standard lathe toolpath configurations for right-hand grooving. What are the main dimensions to consider for machine set-up? Key dimensions are 25 mm head width, 5 mm cutting width and 170 mm overall length, which define reach and stability for fixture and turret planning. Is the bore bar designation important for selecting the holder? Yes — the holder’s compatible bore bar is designated 4C-R MGM, and matching this ensures correct seating and alignment in the toolpost. Manufacturer / Responsible: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Benefit from precise 5 mm cutting width, a maximum parting depth of 18 mm and a robust 25 mm clamping height for stable, repeatable parting operations; order the tool directly via Metav Werkzeuge or consult the technical team for integration advice. Parting clamp holder (Stechklemmhalter) — 5 mm cut width, right-hand, Teknik Makina A reliable parting clamp holder designed for right-hand parting and grooving in lathe applications, compatible with Sandvik indexable inserts and standard ISO 2525 tool interfaces 5 mm cutting width for narrow parting 18 mm maximum parting depth 25 mm head and clamping height Stable clamping for consistent parting results The holder provides a 25 mm clamping height and matching head width, engineered to keep the insert rigid under cutting loads. This dimensioning reduces vibration and runout, which in turn improves surface finish and extends insert life. With a compact overall length of 150 mm, the assembly fits common toolposts while the measured mass of 0.725 kg contributes to predictable dynamic behaviour on the lathe. The design therefore supports steadier cuts and fewer reworks, translating into measurable operational efficiency. Accurate narrow cuts and controlled depth Featuring a 5 mm cutting width and a maximum parting depth of 18 mm, the component is optimised for fine separation and groove operations where material waste must be minimised. The right-hand cutting orientation ensures correct chip flow and predictable engagement when mounted in standard right-hand toolholders. Operators benefit from improved process control: the narrow blade reduces required cutting forces, while the controlled depth capability allows safe, repeatable interventions in batch production or single-part work. Compatibility that simplifies toolroom setup Designed for compatibility with Sandvik indexable inserts and referencing ISO 2525 interfaces, the clamp holder integrates into established tooling systems and boring-bar setups such as the 5C-123 SDV-R designation. This reduces adaptation time and inventory complexity for suppliers and workshops. The holder’s straightforward geometry and standardised attachment reduce downtime for changeovers, supporting continuous workflows and predictable tool maintenance cycles. For dependable right-hand parting, request integration support or order the Teknik Makina parting clamp holder D912TM through Metav Werkzeuge – Metav’s specialists in Emmerich ensure supply and practical advice for seamless workshop adoption. Technical data SKU: D912TM Manufacturer: Teknik Makina ECLASS: 21181005 ISO designation: 2525 Facts Overall length: 150 mm Weight: 0.725 kg Clamping height: 25 mm Head width: 25 mm Holder width: 25 mm Cutting width: 5 mm Maximum parting depth: 18 mm Cutting direction: Right-hand Special features Compatible with Sandvik indexable inserts Suitable for 5C-123 SDV-R boring bar Right-hand cutting direction ISO 2525 tool interface FAQ What cutting direction does this holder support? The holder is configured for right-hand cutting; for right-hand parting operations the Teknik Makina parting clamp holder D912TM provides correct chip flow and tool engagement. Which insert and interface standards are compatible? Compatibility is provided for Sandvik indexable inserts and the holder references the ISO 2525 interface to ease integration into existing tool systems. What is the maximum achievable parting depth? Maximum parting depth is 18 mm with the 5 mm cutting width setup, enabling controlled separation or grooving tasks. Will the holder fit standard toolposts and boring bars? Yes, the overall length of 150 mm and the listed compatibility with the 5C-123 SDV-R designation support common toolpost and boring-bar arrangements. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Benefit from the combination of a precise 5 mm cutting width, a rigid 32 mm clamping body and compatibility with ISCAR 5C GRP inserts for reliable grooving and parting operations; these features deliver repeatable accuracy and stable chip control. Order the parting and grooving clamp holder directly via Metav Werkzeuge or consult our application specialists for machining guidance. Parting and Grooving Clamp Holder D774TM — right-hand, 5 mm cutting width (Teknik Makina) The Parting and Grooving Clamp Holder D774TM is a right-hand toolholder engineered for secure clamping of indexable inserts in turning applications, designed to perform precise grooving and parting tasks on conventional and CNC lathes Right-hand cutting direction 5 mm cutting width for precise grooves Compatible with ISCAR 5C GRP inserts Robust 32 mm block, 170 mm overall length Consistent groove geometry through a rigid construction The D774TM holder combines a 32 mm clamping block and a compact head to provide high rigidity during interrupted cuts and plunge operations. A stiffer holder reduces deflection and contributes directly to consistent groove profile and longer insert life; this reduces rework and increases first-pass yield. The moderate weight (1.264 kg) and balanced geometry help maintain stable cutting dynamics on both manual and automated lathes. Secure clamping and proven insert compatibility Designed for use with ISCAR 5C GRP style indexable inserts, the holder secures the insert in a positive clamp to minimise micro-movement and chatter. The secure fixing improves surface finish on the groove flank and ensures repeatable seating after index changes. The 5 mm cutting width and the clamp geometry allow controlled chip formation, while the interface designation 3232 gives a clear reference for matching toolposts and adaptations. Performance where plunge depth and accessibility matter With a maximum plunge depth of 24 mm, this holder supports deeper grooving tasks without compromising stability. The effective overall length of 170 mm strikes a practical balance between accessibility in the chuck and minimal overhang. These dimensions make the holder suitable for standard parting and slotting operations where reach and tool rigidity must be balanced for efficient cycle times and predictable tool life. Integration into shop workflows and maintenance logic The D774TM is compatible with the common 5C-R GRP shank standard, easing integration into existing toolsets and reducing the need for custom adapters. Familiar clamping and ISO designation simplify inventory and procurement for production environments. Routine maintenance focuses on clamp screws and seating surfaces; regular inspection of the seating plane and prompt replacement of worn inserts will preserve the holder’s low-vibration behaviour and dimensional reliability. Contact Metav Werkzeuge for tailored advice on selecting the correct Teknik Cutting Tools parting and grooving holder for specific materials and machines, or request dimension verification by email at info@metav-werkzeuge.com or by phone on +49 2822 7131930 Technical data Article number: D774TM Manufacturer: Teknik Makina ECLASS: 21181005 Facts Cutting width: 5 mm Max plunge depth: 24 mm Holder height: 32 mm Holder width: 32 mm Head width: 32 mm Overall length: 170 mm Weight: 1.264 kg Cutting direction: right Special features ISO designation: 3232 Tool shank: 5C-R GRP Compatible inserts: ISCAR 5C GRP Designed for indexable inserts and parting/grooving applications FAQ What insert types fit this holder? The holder is compatible with ISCAR 5C GRP indexable inserts; confirm the insert seat matches the 3232 designation for secure clamping. Is the holder suitable for deep grooving tasks? The holder supports a maximum plunge depth of 24 mm, making it appropriate for deeper slotting where a robust clamp is required. Which cutting direction does the tool require? This toolholder is manufactured for right-hand cutting direction and should be mounted accordingly in the toolpost. Can the D774TM be used on both manual and CNC lathes? Yes — the D774TM’s balanced geometry and 170 mm overall length make it suitable for manual and CNC turning centres when used with the correct toolpost and shank standard. What dimensions should be checked before ordering? Verify the holder width/height (32 mm) and the shank interface (5C-R GRP) to ensure compatibility with existing toolposts and machine fittings. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Benefit from the combination of stable support from a 40 mm shank, long 300 mm overall length and reliable compatibility with 5C indexable inserts to streamline parting operations; order the K640TM directly via Metav Werkzeuge or consult our specialists for tailored application advice. K640TM Parting Insert Holder by Teknik Makina — 40 mm shank, 300 mm overall length The K640TM parting insert holder is a robust grooving and parting toolholder designed for lathe applications where repeatable clamping and predictable chip formation are essential 40 mm shank diameter 300 mm overall length Compatible with 5C indexable inserts 5 mm cutting width, 50 mm cutting height Stable support for accurate parting and grooving The 40 mm shank delivers increased rigidity, minimising vibration and improving cutting consistency. This stability directly supports precision in controlled interruptions and fine grooving operations, reducing rework and improving cycle repeatability. The design concentrates mass where it matters: at the toolholder body, which increases effective stiffness and contributes to reliable margin control during interrupted cuts. Fast insert changes and dependable clamping for productivity Compatibility with 5C indexable inserts and the specified clamp arrangement provide rapid insert replacement and secure seat retention. The clamping geometry is optimised for repeatable contact and clamping reliability, lowering setup time and keeping downtime to a minimum. Secure insert retention maintains edge position over long runs, supporting consistent part quality and predictable tool-life management. Suited to workshop and production environments With an overall length of 300 mm and a head diameter of 49 mm, the holder balances reach with rigidity for mid-reach turning and grooving tasks. The tool’s weight 3.109 kg contributes to steady cutting behaviour without excess overhang-induced deflection. As a result, the holder integrates well into both single-machine shops and small production cells where machine capacity and repeatability matter. Clear machining advantages with defined cutting geometry The tool is configured for a 5 mm cutting width and a 50 mm cutting height, dimensions that enable controlled parting and grooving with common insert geometries. Those cut dimensions promote predictable chip formation and evacuation when paired with suitable feeds and speeds, which in turn reduces thermal load on the insert and promotes longer, more economical tool performance. The overall configuration supports stable parting performance and reduced scrap rates. Contact Metav Werkzeuge today to discuss how the K640TM can be adapted to specific turning tasks or to request a technical quotation; Metav Werkzeuge’s advisors are available at info@metav-werkzeuge.com or +49 2822 7131930 Technical data Article number: K640TM Manufacturer: Teknik Makina Designation: Parting insert holder Facts Shank diameter: 40 mm Overall length: 300 mm Diameter: 49 mm Weight: 3.109 kg Cutting height: 50 mm Cutting width: 5 mm Special features Compatible with 5C indexable inserts Tool shank designation: S40T Clamp holder designation: 5C-R S229 Intended for indexable grooving/parting applications FAQ What insert type fits this holder? The holder accepts 5C indexable inserts; the K640TM is specified for plates compatible with that insert family and the 5 mm cutting width. What are the critical dimensions for setup? Key dimensions are a 40 mm shank diameter, 300 mm overall length and a head diameter of 49 mm, which determine clearance and overhang allowances during installation. Is the tool suitable for interrupted cuts? Yes, the K640TM’s robust shank and clamp arrangement are designed to handle interrupted cuts typical in parting and grooving operations, improving stability and edge life. How does the holder affect chip control? The combination of the specified cutting width and height promotes predictable chip formation; when paired with appropriate feed and speed, the holder supports consistent chip evacuation and reduced heat on the insert. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

The combination of 6 mm cutting width, 27 mm max grooving depth and a compact 170 mm overall length ensures efficient, repeatable parting operations with minimal tool changes; order the holder directly via Metav Werkzeuge or consult the advisors for application support. Parting and Grooving Clamp Holder D686TM — Right-hand, 6 mm cutting width (Teknik Makina) A Parting and Grooving Clamp Holder D686TM engineered for right-hand grooving and parting tasks, compatible with Korloy 6C MGM indexable inserts and designed for secure clamp-style fixing in conventional turning applications Right-hand cutting direction 6 mm cutting width 27 mm max grooving depth Compatible with Korloy 6C MGM inserts Stable clamping for consistent grooving results The clamp-style design delivers a secure hold on the indexable insert, producing repeatable groove geometry and reducing vibration during cutting. The larger 25 mm head width increases contact area at the tool tip, which supports stability when parting off or cutting narrow grooves. Where tight tolerances are required, the ISO 2525 designation ensures the tool seat and shank geometry are standardised for predictable mounting; this means set-up is straightforward and the risk of misalignment is reduced. For workshops seeking consistency across batches, the resulting surface finish and dimensional control are tangible benefits. Optimised throughput with broad insert compatibility Specifically matched to 6C MGM inserts from Korloy, the holder accommodates widely available indexable cutting tips, cutting downtime associated with special inserts. The 6 mm cutting width and 27 mm maximum grooving depth enable common parting tasks and moderate-depth grooving in one tool, improving cycle times by limiting tool changes. The right-hand cutting orientation is suitable for standard lathe feed directions; where process planners require consistent tool orientation, the designation removes ambiguity in tool lists and CAM setups. This configuration benefits production lines where reliable, repeatable operations are prioritised. Workshop-ready form and simple maintenance With an overall length of 170 mm and a mass of approximately 0.745 kg, the holder balances rigidity with manoeuvrability for confined turret positions. The tool accepts a 6C-R MGM shank variant for secure clamping in standard toolposts, and the clamp mechanism is designed for rapid insert replacement without complex adjustments. For users less familiar with indexable tooling, the term “indexable insert” refers to a small, replaceable cutting tip; when an edge wears, the tip is rotated or swapped, avoiding the need to regrind the whole tool. The result is lower maintenance overhead and predictable procurement of consumables. For precision grooving with proven clamp technology, contact Metav Werkzeuge for procurement and expert advice — eMail: info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: D686TM Name: Parting and grooving clamp holder (Stechklemmhalter) Manufacturer: Teknik Makina Facts Cutting width: 6 mm Max grooving depth: 27 mm Head width: 25 mm Overall length: 170 mm Weight: 0.745 kg Cutting direction: right-hand ISO designation: 2525 Special features Compatible inserts: 6C MGM (Korloy) Shank / bar designation: 6C-R MGM Clamp-style insertion and fixation Compact design for standard turrets FAQ Which indexable inserts fit this holder? The holder is compatible with 6C MGM indexable inserts; Korloy 6C series inserts are explicitly supported for straightforward procurement and replacement. Is the cutting orientation right- or left-hand? This clamp-type tool is configured for right-hand cutting, suited to standard lathe feed directions and conventional turret setups. What is the maximum grooving depth achievable? The tool supports a maximum grooving depth of 27 mm, allowing moderate-depth grooves and parting operations without supplementary tooling. How does the clamp mechanism affect setup time? The clamp-style fixing enables rapid insert changes and minimal re-alignment, which reduces setup time and maintains consistent cutting geometry. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Benefit from precise parting and grooving with a secure clamp design: the 6 mm cutting width combined with a 32 x 32 mm body delivers controlled cuts up to 20 mm, while the 170 mm overall length improves stability for consistent turning results. Order this tool via Metav Werkzeuge or ask our consultants for application advice. Parting tool clamp holder D051TM — 6 mm cutting blade, 32 x 32 mm body (Teknik Makina) The Parting tool clamp holder D051TM is a right-hand clamped holder for parting and grooving tasks on lathes, built to secure narrow blades and support stable, repeatable machining. Precision 6 mm cutting width Solid 32 x 32 mm clamp body Up to 20 mm max parting depth Compatible with ZCC 6C ZT.D inserts Improved stability for deeper parting operations The combination of a 32 x 32 mm clamp body and an overall length of 170 mm gives the holder a secure footprint in the toolpost, which translates to reduced vibration and improved surface finish during parting. At a weight of 1.331 kg, the mass contributes to steadier cutting dynamics without excessive inertia. This structural balance supports consistent cuts in short-to-medium run production, helping to maintain tolerances and reduce rework rates. Narrow blade precision for fine grooves and parting A 6 mm cutting width is ideal for fine grooving and accurate parting where material saving and minimal stock removal are priorities. The design allows controlled engagement for clean chip formation and predictable cut behaviour, with a maximum usable depth of 20 mm for deeper parting tasks. The holder is configured for right-hand cutting direction, meaning it is optimised for standard right-hand turning operations and lathe set-ups. Streamlined tooling through proven compatibility Compatibility with ZCC inserts of the 6C ZT.D family and the ISO-style designation 3232 simplifies procurement and reduces tooling complexity on the shop floor. Standardised insert fitment ensures predictable seating and repeatability, so replacement inserts can be sourced and installed quickly. For operations that rely on consistent interchangeability, this holder helps to shorten set-up time and maintain process reliability. Secure clamping for reliable production cycles As a clamp-style holder, the unit provides secure clamping of the insert blade to avoid micro-movement under load, which supports consistent tool life and predictable machining performance. The robust construction is aimed at workshops and subcontractors who require dependable parting and grooving hardware for series production as well as single-piece work. The D051TM is designed for straightforward integration into existing tool posts and turning workflows where repeatability matters. For tailored advice on integrating the Teknik Makina D051TM into the workshop or to arrange prompt delivery from Metav Werkzeuge, please contact Metav Werkzeuge by phone at +49 2822 7131930 or by e‑mail at info@metav-werkzeuge.com Technical data Article number: D051TM Manufacturer: Teknik Makina Product: Parting tool clamp holder Core data Body width: 32 mm Cutting head width: 32 mm Holder height: 32 mm Cutting blade width: 6 mm Max parting depth: 20 mm Overall length: 170 mm Weight: 1.331 kg Cutting direction: right-hand Features Compatible with ZCC 6C ZT.D inserts ISO designation: 3232 Boring bar designation: 6C-R ZT-D eClass: 21181005 FAQ Which insert types fit this holder? The holder accepts ZCC inserts in the 6C ZT.D family; compatibility is specified to match the 6C ZT.D insert geometry and ISO-style 3232 seating. What is the maximum parting depth? Maximum parting depth is 20 mm, suitable for many standard parting and grooving tasks on conventional lathes. Is the cutting direction left- or right-hand? This tool is configured for right-hand cutting, intended for right-hand turning operations. What are the key external dimensions? Body and head dimensions are 32 x 32 mm with an overall length of 170 mm, offering a compact but stable footprint. For which applications is the holder intended? Designed for lathe parting and grooving operations where narrow, precise cuts are required and compatible with series production environments. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Benefit from the combination of a 4 mm cutting width, a 25 mm head, and reliable left-hand orientation to achieve precise, repeatable parting operations — order the parting tool holder directly via Metav Werkzeuge or consult the technical advisers for setup recommendations. Parting clamp holder D811TM by Teknik Makina — left‑hand, 4 mm cutting width Parting clamp holder D811TM for precision parting and grooving on lathes; compatible with Korloy MGM 4 inserts and designed for robust workshop use Left-hand cutting direction Fits MGM 4 Korloy inserts 4 mm cutting width for narrow grooves Robust 25 mm head width, 150 mm length Precise parting with minimal material loss The D811TM is engineered for narrow, controlled parting operations where consistency matters. The 4 mm cutting width and a maximum parting depth of 20 mm provide precise kerf control, reducing scrap and the need for rework. A maximum effective turning diameter of 150 mm allows reliable use on small to medium workpieces; the 45 mm cutting height helps maintain stable insert engagement and predictable chip flow. These measured characteristics translate directly into less downtime and fewer rejected parts in series production. Secure clamping and broad insert compatibility Clamping stability is critical when parting under load. The holder's 25 mm head width and ISO 2525 shank designation contribute to a rigid seating for the insert, while the unit accepts MGM 4 style inserts from Korloy, ensuring access to widely available carbide grades and geometries. The tool also matches the 4C-L (110–150) boring‑bar sizing for integration into modular setups. Together, these attributes reduce setup iterations and permit rapid replacement of cutting tips, supporting steady cycle times on shop floors. Built for workshop throughput and handling With an overall length of 150 mm and a mass of 0.712 kg, the holder balances rigidity and manoeuvrability for manual and semi‑automatic lathe operations. The left‑hand geometry is suited to specific spindle orientations and fixture arrangements, enabling operators to keep machine programmes and tooling stacks compact. The combination of compact dimensions and measured weight improves access in confined setups and helps to maintain cutting stability at higher feed rates, delivering a noticeable improvement in machining efficiency. Practical notes for machining and maintenance To preserve clamping repeatability and tool life, ensure the insert seat is clean and the clamping screw is correctly torqued; the unit’s design supports straightforward maintenance without specialised fixtures. Selecting appropriate Korloy insert grades for the workpiece material — for example, tougher grades for interrupted cuts or tougher steels — will optimise performance. The holder’s left‑hand orientation and defined dimensions make it straightforward to plan toolpaths and fixture arrangements in multi‑station production environments, reducing the chance of collisions and unscheduled stops. Contact Metav Werkzeuge today for tailored application advice on the Teknik Makina D811TM parting clamp holder; call +49 2822 7131930 or email info@metav-werkzeuge.com for technical consultation and delivery options Technical data Article number: D811TM Manufacturer: Teknik Makina Dimensions & core figures Overall length: 150 mm Head width: 25 mm Cutting width: 4 mm Maximum cutting diameter: 150 mm Maximum parting depth: 20 mm Cutting height: 45 mm Shaft cutting length: 25 mm Mass: 0.712 kg Materials & special features Compatible inserts: MGM 4 Suitable insert manufacturer: Korloy Shank/holder designation: ISO 2525 Boring-bar compatibility: 4C-L (110-150) Cutting direction: left FAQ What insert types fit this holder? The parting clamp holder D811TM is designed for MGM 4 style inserts and lists Korloy as a suitable insert manufacturer for these seats. Is the tool suitable for large diameters? The holder supports operations on workpieces up to a maximum cutting diameter of 150 mm, making it appropriate for small to medium turning tasks. Which cutting direction does the holder require? This model is configured for left‑hand cutting, which should be matched with the lathe spindle and programme orientation during setup. How deep can the tool cut in one pass? The design provides a maximum parting or plunging depth of 20 mm, enabling controlled, narrow groove and parting operations. What are the key dimensions to consider for fixture planning? Important dimensions include 150 mm overall length, 25 mm head width and a 45 mm cutting height; these figures aid collision checks and programme preparation. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Designed for precise right‑hand grooving and dependable parting, the tool combines a 32 mm clamping head, a 2 mm cutting width and a maximum grooving depth of 16 mm to deliver repeatable results and reduced setup time. Order the grooving tool holder directly via Metav Werkzeuge or consult our specialists for fitment and tooling advice. Grooving tool holder D666TM — right‑hand holder with 32 mm clamping head Grooving tool holder D666TM is a right‑hand CNC turning holder engineered for precision grooving and parting operations using 2C MGM turning inserts 32 mm clamping head width 2 mm cutting width for fine grooves Max grooving depth 16 mm Compatible with Korloy 2C MGM inserts Faster, more reliable grooving for production environments The holder is built to streamline grooving cycles by providing a stable clamping interface and a compact profile that reduces vibration. With a 32 mm clamping head and a designated 2 mm cutting width, the system supports narrow groove creation while maintaining dimensional stability. The robust design shortens cycle variability, which helps to increase throughput in repetitive turning tasks without compromising surface finish. Compatibility that reduces setup complexity Compatibility with Korloy turning inserts of the 2C MGM type and the shank designation 2C‑R MGM simplifies inventory and tool changeover. The ISO designation 3232 identifies a standardised interface that integrates with common turret and toolpost fixtures, allowing workshops to use existing insert families and minimise downtime for insert procurement. This level of compatibility translates into fewer spare parts and faster reconditioning. Engineered for workshop durability and repeatable accuracy The holder’s overall length of 170 mm and a solid mass of 1.349 kg provide the rigidity required for clean parting cuts and controlled chip formation. The right‑hand cutting direction and the secure clamping geometry ensure that insert seating remains consistent across extended runs, reducing the need for frequent readjustment. The result is a toolholder that sustains accuracy in harsh machining conditions and supports predictable tool life. Practical features that aid daily use and tool management A maximum grooving depth of 16 mm allows the holder to tackle a broad range of groove profiles while remaining compact enough for close‑tolerance work. The clearly defined cutting and clamping dimensions make it straightforward to plan toolpaths and to select suitable inserts and feed rates. Specifying the correct insert geometry alongside the holder decreases trial runs and improves first‑pass yield, delivering measurable gains in production efficiency. For tailored compatibility checks or to secure the Teknik Cutting Tools grooving tool holder (D666TM), contact Metav Werkzeuge in Emmerich for expert advice and reliable supply: phone +49 2822 7131930 or email info@metav-werkzeuge.com Technical data Article number: D666TM Name: Stechklemmhalter (Grooving tool holder) Manufacturer: Teknik Makina Facts Clamping head width: 32 mm Cutting width: 2 mm Max grooving depth: 16 mm Overall length: 170 mm Weight: 1.349 kg Special features Right‑hand cutting direction Compatible with Korloy 2C MGM inserts ISO designation: 3232 Toolholder shank designation: 2C‑R MGM FAQ What insert type fits this holder? The grooving tool holder accepts 2C MGM style inserts and is specifically noted as compatible with Korloy 2C MGM turning inserts for straightforward matching. What is the maximum grooving depth? The toolholder is rated for a maximum grooving depth of 16 mm, suitable for common parting and grooving operations on medium‑duty lathes. Is the cutting direction right or left? This holder is configured for a right‑hand cutting direction, optimised for right‑hand parting and grooving cycles. What are the key dimensional data for fixture planning? Useful dimensions for planning include a 32 mm clamping head width, an overall length of 170 mm, and a 2 mm nominal cutting width. Which model and manufacturer designation should be referenced for ordering? Reference the model D666TM from Teknik Makina when ordering the grooving tool holder to ensure the correct ISO 3232 interface and shank compatibility. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of the combination of robust clamping, precise 3 mm cutting width, and 200 mm overall length to ensure consistent parting and grooving performance; order the tool directly via Metav Werkzeuge or consult our specialists for application-specific advice. Grooving clamp holder »K606TM« by Teknik Makina — 25 mm shank, 200 mm overall length The Grooving clamp holder »K606TM« is a clamp-style holder engineered for accurate parting and grooving on conventional lathes, compatible with 3C MGM inserts for stable chip control in standard turning workflows. 25 mm shank for stable clamping 200 mm overall length for extended reach Compatible with 3C MGM Korloy inserts 3 mm cutting width for precise grooves Optimised stability for repeatable parting and grooving Designed with a 25 mm shank and a substantial 200 mm overall length, this holder delivers the torsional rigidity required for repeatable groove and parting operations. The combination of a compact mass (approx. 0.784 kg) and a solid shank diameter reduces vibration at the cutting edge, which in turn supports consistent surface finish and longer insert life. The holder`s geometry is suited for workshop environments that demand dependable clamping behaviour during medium-duty turning tasks on standard lathes. Accurate insert alignment and controlled chip formation Compatibility with 3C MGM inserts and suitability for Korloy-referenced grades mean that the toolholder provides precise seating and repeatable cutter orientation. A cutting width of 3 mm and a cutting height of 40 mm allow for narrow, well-defined grooves with minimal material waste. The ISO-style designation S25R 3C-R underlines the accepted shank format for mounting and tool post fitting, enabling straightforward tool changes and consistent insert positioning during series production. Workshop efficiency and straightforward maintenance The holders straightforward clamp mechanism (type **MGM**) supports quick insert replacement and secure locking without complex adjustment; the result is reduced downtime and a clearer tool inventory strategy. With a nominal outer diameter of **32 mm**, the component integrates into typical turret and tool post systems while maintaining a compact footprint. The units balanced weight and machining-friendly form make it a practical choice for trade and light industrial shops seeking a reliable grooving solution that pairs with widely available Korloy inserts. Contact Metav Werkzeuge today for application advice on Teknik Makina grooving systems and request the K606TM to optimise parting operations directly from our Emmerich supply hub, phone +49 2822 7131930 or email info@metav-werkzeuge.com Technical Data Article number: K606TM Manufacturer: Teknik Makina Product name: Grooving clamp holder (Stechklemmhalter) Facts Shank diameter: 25 mm Overall length: 200 mm Cutting height: 40 mm Cutting width: 3 mm Outer diameter: 32 mm Weight: 0.784 kg Special features Compatible with 3C MGM inserts Suitable for Korloy inserts ISO designation: S25R 3C-R Clamp type: MGM FAQ What inserts fit the Grooving clamp holder »K606TM«? The Grooving clamp holder »K606TM« is specified for 3C MGM style inserts and is listed as compatible with Korloy insert types. Which shank size does the K606TM require? The K606TM features a 25 mm shank (ISO S25R 3C‑R), ensuring rigid mounting in standard tool posts and turret systems. What groove width can be machined with this holder? This holder supports a 3 mm cutting width, which is suitable for narrow parting and precision grooving tasks. Is the holder suitable for automated turret systems? The K606TM`s dimensions, including a 200 mm overall length and a 32 mm outer diameter, allow integration into many turret and tool post arrangements where a clamp-style grooving holder is required. How does the clamp design affect insert changes? The MGM clamp design on the K606TM provides secure locking and straightforward insert replacement, reducing downtime during tool changes. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of a compact, purpose-fit tool: the combination of a T10 tip and a lightweight form supports efficient assembly and reduced rework. Secure the required item directly via Metav Werkzeuge or consult the team for application advice. Torx key T10 — Compact workshop hand tool by Teknik Makina Torx key T10 for precise engagement with Torx fasteners in maintenance, assembly and general workshop tasks T10 tip for Torx fasteners Lightweight at 0.1 kg for easy handling Compact hand tool for tight spaces Manufactured by Teknik Makina Reduced fastener wear through precise engagement A tool with a defined T10 geometry offers precision engagement that lowers the risk of cam‑out and rounded fastener heads; this translates directly into fewer repairs and less downtime on the shop floor. The proven fit of the bit to the fastener head enables consistent torque transmission, which is particularly relevant when repeatability matters in serial assembly or scheduled maintenance. By relying on a single-size driver for matching fasteners, processes become more predictable and quality control is simplified. Easier access and controlled handling in confined areas The compact format of the driver improves access to recessed or obstructed fasteners and supports steady handling during intricate tasks. Thanks to its lightweight nature — 0.1 kg — manoeuvring the tool is less fatiguing over repeated cycles, improving operator comfort and reducing the likelihood of slips. Where service engineers face limited clearance, a compact driver maintains controlled leverage while allowing for precise alignment, which speeds up on-site interventions and small-batch production work. Simple stock management and workshop compatibility A single-purpose hand tool such as this reduces inventory complexity: keeping the designated Torx size on hand avoids unnecessary tool swaps and eases procurement. The item is identified under SKU T10TM and integrates seamlessly into workbenches and tool trolleys used in light industrial, trade and maintenance environments. Sourcing from a recognised maker ensures consistent supply, while the tool’s straightforward specification supports training and standardisation across teams. For reliable workshop fastening, contact Metav Werkzeuge to discuss the Teknik Makina T10 option and confirm suitability for the intended applications — email info@metav-werkzeuge.com or call +49 2822 7131930 for expert guidance Technical data Article number: T10TM Manufacturer: Teknik Makina Torx size: T10 Weight: 0.1 kg eCl@ss: 21189290 Facts Weight: 0.1 kg eCl@ss code: 21189290 Special features Tool type: Torx key for T10 fasteners Compact design for tight access Suitable for assembly and maintenance FAQ What Torx size does this tool fit? The tool fits T10 Torx fasteners; the Teknik Makina Torx key (SKU T10TM) was specified for that size. Is the driver suitable for use in confined spaces? Yes, the compact hand tool design is intended for tight access and maintains control when reaching recessed fasteners. How much does the tool weigh and how does that affect use? Weighing 0.1 kg, the lightweight construction reduces operator fatigue during repeated use and supports steady handling. Can this driver be included in a standard workshop kit? The Torx key is straightforward to stock and integrate into workshop sets; SKU T10TM simplifies inventory tracking. Who manufactures this Torx key and where can advice be obtained? The tool is produced by Teknik Makina; for purchasing guidance or application questions consult Metav Werkzeuge as noted above. Teknik Makina: Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of the compact T15 Torx key with a precision tip and a light 0.1 kg handling weight for efficient fastening in workshop tasks; order or request further advice via Metav Werkzeuge for a reliable supply. Torx key T15 (T15TM) – Compact Torx key by Teknik Makina A Torx key T15 designed for secure engagement with T15 Torx fasteners in maintenance, assembly and workshop environments. Precision T15 tip for Torx fasteners Lightweight: 0.1 kg for easy handling Compact design for tight spaces Suitable for professional workshop use Reliable engagement reduces rework and improves throughput The precision-machined T15 tip ensures a secure interface with Torx fasteners, which reduces the risk of slipping and stripped heads. This technical fit improves torque transfer and leads to fewer repeat operations — a measurable benefit for production and maintenance workflows. The clear specification of the tip size supports quick tool selection and avoids time lost on trial fitting, contributing to a smoother, more efficient assembly process. Compact, lightweight handling for faster tasks With a total weight of 0.1 kg, the tool is easy to manipulate for repetitive fastening work and offers noticeably reduced hand fatigue during extended use. The compact form factor is particularly useful where access is restricted, enabling tasks to be completed faster and with greater confidence. The light construction also streamlines storage and transport within mobile tool kits or service vans, aiding rapid response in field servicing. Practical addition to a professional toolkit with dependable sourcing This Torx key is a straightforward addition to workshop toolsets where standardised fastener systems are used. The clearly stated T15 designation supports compatibility planning across maintenance inventories. Sourcing via Metav Werkzeuge adds logistical reliability: Metav’s Emmerich location acts as a quality filter for the European market, ensuring consistent supply and simplifying procurement for industry and trade. Contact Metav Werkzeuge today to confirm availability of the Teknik Makina Torx key T15 (SKU T15TM) and to arrange a tailored supply for workshop or service requirements Technical data Article number: T15TM Manufacturer: Teknik Makina ECLASS: 21189290 Facts Torx size: T15 Weight: 0.1 kg Features / Applications Compatible with Torx T15 fasteners Intended for workshop and maintenance use FAQ What size fasteners does this key fit? The Torx key T15 fits Torx fasteners specified as T15; the size is indicated on the SKU T15TM. Is the tool suitable for professional use in a workshop? The Torx key T15 is described for workshop and maintenance applications and is suitable for professional tool kits. What is the weight of the Torx key T15? The listed weight for the Torx key T15 (SKU T15TM) is 0.1 kg. Manufacturer / Responsible: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of a precision T20 drive and ultra-lightweight handling to speed up assembly tasks and reduce operator fatigue; the compact format keeps workshop inventory manageable. Order directly via Metav Werkzeuge or ask the consultants for procurement advice. Torx key T20 — compact T20 drive for workshop and assembly The Torx key T20 is a compact hand tool designed for fast, reliable engagement with T20 fasteners across maintenance, assembly and repair tasks Torx key T20 precision fit Lightweight, only 0.1 kg handling ease Ideal for assembly and repair tasks Teknik Makina original SKU T20TM Faster, more reliable engagement with Torx fasteners The Torx geometry reduces slipping under load and provides a precision fit that translates into fewer cam‑outs and faster screwdriving cycles. With the marked T20 drive size, this key matches the ISO‑defined Torx profile and is suited for repeatable operations where consistency matters. The drive form is explained here so non‑specialists understand the benefit: the star‑shaped recess transfers torque across multiple contact points, lowering the risk of tool and fastener damage and thereby improving process throughput and component longevity. Reduced fatigue through light handling and compact design At just 0.1 kg, the tool supports long routines without adding cumbersome weight to the toolbox. The low mass makes it suitable for technicians and assembly staff who perform many fastening actions per shift, supporting smoother workflows and improved ergonomics. The compact footprint keeps pockets and small toolkits organised and helps speed up task changes on the workbench. The direct consequence is shorter handling times and less strain during repetitive tasks, a practical plus in both workshop and production environments. Straightforward stock management and compatibility Available as SKU T20TM from Teknik Makina, the item is easy to catalogue and reorder for maintenance spares. The clear designation of the Torx size simplifies procurement and reduces the chance of incorrect parts being purchased. For companies consolidating suppliers, the short SKU and concise specification enable predictable replenishment and audit trails. The small, clearly identified tool supports lean inventory practices and swift identification on the workbench. For procurement or volume requirements of the Teknik Makina Torx key T20, contact Metav Werkzeuge in Emmerich for ordering and supply coordination at +49 2822 7131930 or info@metav-werkzeuge.com Technical data Article number: T20TM Manufacturer: Teknik Makina ECLASS: 21189290 Torx size: T20 Weight: 0.1 kg Numerical data Weight (kg): 0.1 ECLASS: 21189290 Features Suitable for Torx T20 fasteners SKU: T20TM Brand: Teknik Makina FAQ What size of fasteners does this tool fit? The tool fits Torx size T20 fasteners; the designation is indicated on the SKU T20TM. Is the T20 key suitable for repetitive assembly work? Yes, the T20 key by Teknik Makina is designed for regular use and its 0.1 kg mass supports reduced operator fatigue in repetitive tasks. How is the Torx drive beneficial compared with slotted or Phillips heads? The Torx drive distributes torque across multiple contact surfaces, reducing cam‑out and wear on both tool and fastener, which improves process reliability. Can the tool be identified easily for reordering? Yes, the clear SKU T20TM and the labelled Torx size simplify stock management and reordering. Who manufactures this Torx key? The tool is from Teknik Makina; the product is supplied under SKU T20TM and distributed via Metav Werkzeuge for European customers. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of a compact T6 size and a lightweight design combined with proven longevity for reliable, repeatable fastening in confined spaces; order the Torx key T6 directly via Metav Werkzeuge or ask our consultants if needed Teknik Makina Torx key T6 — Compact T6 Torx key, lightweight and precise The Torx key T6 is a compact fastening tool designed for precision assembly and maintenance tasks in workshops and production lines, offering a small footprint for tight access and consistent torque transmission Compact T6 size for tight spaces Lightweight construction — approx. 0.1 kg Long service life for repeated use Fast dispatch from stock Precision where access is limited A small-form T6 tool delivers accurate engagement with Torx fasteners in confined assemblies. The compact geometry ensures reliable contact between driver and screw head, reducing cam‑out and rounding. For production and repair environments this translates into fewer rework cycles and a stable process flow; the slender form factor also enables access in recesses where larger drivers cannot operate, improving throughput in tight‑tolerance work. Consistent handling and measurable efficiency Weighing around 0.1 kg, this key offers a noticeably low mass that reduces operator fatigue during repetitive tasks. Lower weight, combined with the standardised Torx profile, permits swift manual operations and precise small‑assembly work. The result is improved cycle times and a repeatable fastening sequence, which supports quality assurance efforts and reduces the need for costly corrective measures. Built to last for demanding applications Designed for extended use, the tool provides a long service life suitable for workshop and light industrial settings. The proven durability reduces replacement intervals and supports predictable maintenance planning. By favouring a tool with sustained performance characteristics, inventories become leaner and process reliability increases, contributing to overall cost-efficiency in tooling management. Simple integration into the workshop toolkit The compact driver is a straightforward addition to existing tool assortments and maintenance kits. Its standard T6 profile ensures compatibility with common Torx fasteners used across electronics, instrumentation and mechanical assemblies. Clear labelling and a compact footprint make storage and identification easier on crowded benches, supporting efficient workflow organisation. Reliable supply and traceability Sourced through an established distribution channel, this T6 key benefits from rapid fulfilment from stock and established logistics, helping to avoid production delays. Traceability via the article identifier supports inventory control and tool‑management routines, enabling maintenance planners to keep track of tooling condition and replacement needs without guesswork. For dependable, compact fastening choose Teknik Cutting Tools’ Torx key T6 and contact Metav Werkzeuge for expert advice and fast supply from Emmerich — eMail info@metav-werkzeuge.com or call +49 2822 7131930 Technical Data Article number: T6TM SKU: T6TM Manufacturer: Teknik Makina Size: T6 Weight: 0.1 kg ECLASS: 21189290 Facts Numerical identifier: T6TM Weight (kg): 0.1 ECLASS code: 21189290 Special features Compact Torx profile Suitable for access-restricted applications Noted long service life in product description Fast dispatch / from stock Listed by Teknik Makina FAQ What size of screw is this key intended for? The T6 size matches standard Torx fasteners specified as T6; the Torx key T6 is designed for secure engagement with that profile. Is this tool suitable for repeated workshop use? Yes — the key is described with a long service life, making it appropriate for frequent manual operations in assembly and maintenance. How heavy is the driver and does that affect handling? Weighing approximately 0.1 kg, the driver is lightweight, which supports comfortable handling during repetitive tasks and reduces operator fatigue. Can this key reach fasteners in tight or recessed positions? The compact geometry of the T6 profile enables access in confined spaces and recessed screw heads, improving usability in restricted assemblies. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Light, precise and workshop-ready: the T7 Torx key combines secure engagement for fine fasteners with a compact 0.1 kg form factor and clear SKU identification for effortless procurement. Order directly via Metav Werkzeuge or consult the Metav team for specification matching. Torx key T7 by Teknik Makina — Compact hand tool for fine Torx fasteners The Torx key T7 is a precision hand tool intended for secure fastening of small Torx screws in compact assemblies and maintenance tasks T7 Torx size for small fasteners Lightweight tool at 0.1 kg Compact format suitable for workshop kits Supplied by Teknik Makina Secure engagement for fine assemblies The T7 tip provides a secure fit with minimal cam‑out, which supports reliable torque transfer in delicate fastening tasks. By reducing slippage the tool helps to protect screw heads and mating components during repeated use, improving process consistency on small assemblies. The clear geometry of the drive interface ensures predictable contact between key and fastener; this contributes to fewer rework cycles and steadier assembly quality, especially where precision counts. Compact format that speeds workshop workflows Weighing just 0.1 kg, the key is designed for easy handling and rapid tool changes in busy workshops. The compact format makes integration into maintenance kits and instrument pouches straightforward and keeps bench clutter to a minimum. The item is listed under SKU T7TM, enabling quick identification in procurement systems and simple stock replenishment. Lightweight handling combined with distinct identification supports faster task cycles and clearer inventory control. Trusted supply and practical procurement advantages Sourcing through Metav Werkzeuge brings transparency and reliability to procurement. Metav’s position as a European quality filter — serving over 48,000 customers with a broad range of precision workshop supplies — means the item is available within an established supply chain from Emmerich. This distribution setup reduces lead times and centralises product selection, making specification checks and repeat orders more efficient for industrial and trade customers. The combination of a compact, precision tool and dependable supply supports continuous workshop operation. For procurement advice or to request a specification match for Teknik Makina tools, contact Metav Werkzeuge and quote SKU T7TM for quick handling and tailored recommendations Technical data Article number: T7TM Manufacturer: Teknik Makina Product: Torx key T7 Facts Weight: 0.1 kg eClass: 21189290 Special features Size: T7 Torx Tool type: Hand tool Format: Compact Origin: Teknik Makina FAQ What applications suit a T7 Torx key? The Torx key T7 from Teknik Makina is suitable for fastening small Torx screws commonly found in precision instruments and compact assemblies; reference SKU T7TM when specifying the tool. How is the T7 size identified on fasteners? A T7 tip matches the internal star profile marked as T7; the Teknik Makina Torx key T7 aligns with standard Torx geometry for consistent engagement, SKU T7TM. Can this key be used for repeated workshop tasks? The Torx key T7 is intended for routine hand assembly and maintenance operations; Teknik Makina designs the tool for regular use in workshop environments (see SKU T7TM for procurement). What measures reduce screw head damage when using the key? Correct seating of the T7 tip and steady, controlled torque minimise cam‑out; using the Torx key T7 in the proper application helps protect screw heads and mating parts (SKU T7TM). Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Compact, precise and purpose-built: the combination of a true T8 Torx profile and a lightweight 0.1 kg body ensures reliable engagement in confined assemblies; order the part directly via Metav Werkzeuge or consult the technical advisers if guidance is required. Torx key T8 — compact Torx hand key by Teknik Makina for precise Torx T8 engagement The Torx key T8 is an efficient hand tool for precise engagement with Torx T8 fasteners in tight or recessed assemblies, designed for routine workshop and maintenance tasks Precision T8 Torx tip for accurate engagement Compact design for confined spaces Lightweight at 0.1 kg for easy handling Precise engagement that reduces cam‑out and rework A defined Torx T8 profile provides a secure interface with the fastener head, which reduces the risk of rounding and cam‑out during assembly operations. The controlled geometry of the tip enables consistent torque transfer when used with manual operation, delivering measurable improvements in fastening reliability. For production or repair work where repeatable results matter, the precise drive profile supports faster cycle times and fewer rework loops compared with worn or improvised tools. Space‑saving form for demanding assembly environments The compact format of this hand key is intended for access in shallow bores, recessed fixings and electronics enclosures where clearance is limited. The reduced length and low mass make it simpler to manoeuvre in restricted spaces, improving accessibility without sacrificing engagement quality. This combination of compact design and secure tip geometry helps maintain assembly speed and reduces the time required to reach awkward fasteners, adding practical value in day‑to‑day workshop use. Practical specification and workshop suitability With a measured mass of 0.1 kg, the key offers tactile control and minimal operator fatigue during repetitive tasks. The tool is identified by SKU T8TM, enabling straightforward stock control and reordering. As a simple, hand‑operated solution the tool integrates cleanly into standard maintenance kits and tool rolls, providing a dependable, no‑frills method for handling Torx T8 fasteners across a range of common applications. For consistent, compact fastening use the Teknik Makina T8 Torx key — contact Metav Werkzeuge in Emmerich for procurement or technical guidance via info@metav-werkzeuge.com or +49 2822 7131930 Technical data Article number: T8TM Torx size: T8 Manufacturer: Teknik Makina Facts Weight: 0.1 kg eClass: 21189290 Special features Compact design Precision Torx tip Hand tool, SKU T8TM FAQ What fastener size is compatible with this key? The key fits Torx T8 fasteners; the tool profile is manufactured for secure engagement with T8 heads. Is the tool suitable for confined or recessed fixings? Yes, the compact form factor is intended to provide access in confined spaces and shallow recesses. How is the item referenced for ordering and stock control? The product is listed under SKU T8TM, which should be used for procurement and inventory purposes. Can this key be stored in a standard workshop tool roll? The light weight and compact dimensions make the key well suited for inclusion in common workshop kits and tool rolls. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of the combination of precise chip control, robust indexable-insert compatibility and integrated cooling for uninterrupted boring operations; order the boring bar directly via Metav Werkzeuge or consult our specialists for technical advice. Boring bar KA181TM – for TCMT 16T3 indexable inserts with internal coolant The Boring bar KA181TM is a precision tool designed for stable boring with TCMT 16T3 indexable inserts, combining a 90° cutting geometry with an integrated coolant channel for consistent machining results. Internal coolant for improved tool life Compatible with TCMT 16T3 indexable inserts 90° cutting angle for precise boring Robust design by Teknik Makina Consistent hole geometry through stable cutting dynamics The KA181TM boring bar delivers repeatable results thanks to its 90° cutting angle, which promotes axial stability and reduces radial deflection during machining. This geometry is particularly effective for maintaining concentricity and dimensional tolerances when using indexable inserts, resulting in fewer rework cycles and more reliable production parts. The solid construction minimises vibration, so feed and speed can be applied with confidence while preserving surface finish quality. Targeted coolant flow to protect inserts and reduce downtime An integrated internal coolant channel directs cutting fluid towards the cutting zone, improving chip evacuation and thermal management at the tool–workpiece interface. Better cooling reduces insert wear and the likelihood of built-up edge, extending tool life and reducing changeover frequency. For operations where consistent cycle times and predictable maintenance intervals matter, this targeted coolant delivery translates into measurable gains in uptime and process stability. Seamless integration with indexable systems and workshop setups Designed specifically for use with TCMT 16T3 indexable inserts, the boring bar fits directly into common toolholder arrangements and supports quick insert changes for minimal interruption. The product's clear specification and industrial provenance from Teknik Makina make it straightforward to plan replacements and stocking. Delivery and logistics are handled from Metav Werkzeuge’s Emmerich facility, ensuring dependable availability for production schedules and a transparent supply chain. Contact Metav Werkzeuge today for detailed compatibility guidance and to secure the Teknik Makina KA181TM boring bar with internal coolant from our Emmerich stock Technical Data Article number: KA181TM Product type: Boring bar Brand: Teknik Makina For inserts: TCMT 16T3 Internal coolant: Yes Facts Cutting angle: 90° ECLASS: 21180806 SKU: KA181TM Special features Internal coolant channel Compatibility with TCMT 16T3 indexable inserts Label: Boring bar TCMT 16T3 with internal coolant Manufacturer: Teknik Makina FAQ Is the boring bar compatible with TCMT 16T3 inserts? The KA181TM boring bar is designed specifically for TCMT 16T3 indexable inserts and accepts this insert type for straightforward assembly. How does the internal coolant improve performance? The internal coolant channel in the KA181TM directs fluid to the cutting edge to enhance chip evacuation and reduce thermal loading on the insert, prolonging service life. Can the boring bar be used in standard toolholders? The KA181TM is intended for integration into conventional toolholder setups that accommodate boring bars and indexable-insert tooling; check holder specifications to ensure correct fit. What production advantages does the 90° cutting angle provide? A 90° cutting angle promotes axial stability and accurate hole geometry, helping to maintain concentricity and reduce the need for subsequent machining corrections. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com