Gibt es einen Hahn und Kolb Online Shop?

Take advantage of a compact, purpose‑built clamp holder that combines reliable indexable‑insert compatibility with stable clamping and a short overhang for reduced vibration — ideal for left‑hand turning operations. Order directly via Metav Werkzeuge for fast delivery or consult the technical team for tailored set‑ups. Klemmhalter DCLN for CN-- Indexable Inserts (DCLNL 2020) — Left‑hand turning, 95° cutting angle — Teknik Makina The Klemmhalter DCLN for CN-- Indexable Inserts is a left‑hand turning toolholder designed for use with CN-- 1204 indexable inserts, offering a compact footprint and secure clamping for stable lathe operations Left‑hand orientation for reversing cuts Compatible with CN-- 1204 inserts 95° cutting angle for stable engagement Compact 125 mm length for tight setups Robust clamping with 20 mm holder height Stable cutting performance for left‑hand turning The DCLN‑style holder is engineered to provide predictable chip formation and consistent contact between insert and workpiece. With its 95° cutting angle and specification as DCLNL 2020, the design directs cutting forces into the tool body to reduce deflection. This results in improved surface finish and longer insert life when performing left‑hand turning or facing tasks. The combination of angle geometry and insert compatibility makes the holder suitable for repeatable production runs where process stability is essential. Space‑saving design that reduces overhang A short overall length of 125 mm and a compact cross‑section help to minimise tool overhang and vibration in confined toolposts. The holder’s 20 mm body width and 25 mm cutting‑head width are balanced to fit tight setups while maintaining rigidity. The modest mass of 0.441 kg further reduces inertial forces, making the component a practical choice for smaller lathes and workshops aiming to increase spindle speeds or shorten cycle times without sacrificing control. Secure clamping and straightforward insert handling Designed for CN-- 1204 inserts, the clamp mechanism gives repeatable seat alignment and reliable retention during interrupted cuts. The 20 mm clamp height and 30 mm cutting height ensure the insert is presented at the correct datum for consistent engagement. For users less familiar with indexable tooling: an indexable insert is a replaceable cutting tip that can be rotated or replaced when worn, delivering economical and fast restoration of cutting performance compared with brazed or tipped tools. Practical applications and target environments This holder suits workshops, maintenance departments and light production where left‑hand turning or reverse‑direction cuts are required. It is appropriate for general turning, profiling and facing when used with compatible CN-- 1204 inserts and a matching K12 shank designation for secure toolpost mounting. The technical specification supports efficient changeovers and predictable tool behaviour — key attributes when throughput and process reliability are priorities. For tailored advice on integrating the Teknik Makina DCLN holder into existing tool setups or for ordering assistance, contact Metav Werkzeuge — our experts in workshop precision are available to recommend the right combination for the application and to ensure prompt supply from Emmerich. Technical data SKU: D301TM Manufacturer: Teknik Makina Designation: DCLN for CN-- Indexable Inserts ISO designation: DCLNL 2020 Dimensions & weights Overall length: 125 mm Weight: 0.441 kg Holder height: 20 mm Head width: 25 mm Body width: 20 mm Cutting height: 30 mm Cutting angle: 95° Features & compatibility Compatible inserts: CN-- 1204 Cutting direction: left Shank / bar designation: K12 Application: indexable‑insert turning FAQ What inserts fit this holder? The holder accepts CN-- 1204 indexable inserts; the DCLN geometry is matched to that insert format for reliable seating and cutting. Is the toolholder suitable for left‑hand turning only? Yes — the toolholder is specified for left cutting direction and is intended for reversing cuts on lathes. What are the key dimensions to check for machine compatibility? Check the 125 mm overall length, 20 mm holder height and the K12 shank designation to ensure the holder fits the toolpost and provides sufficient rigidity. Which SKU and manufacturer should be referenced when ordering? Reference SKU D301TM and the Teknik Makina designation DCLN for CN-- Indexable Inserts when enquiring or ordering. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Benefit from the combination of a defined 93° cutting angle and a 40 mm cutting height that deliver stable engagement and predictable chip flow. The compact overall length and precise clamping reduce setup time and tool changes for small- to mid-series turning. Order the DVJN tool holder directly via Metav Werkzeuge or ask our consultants if needed. DVJN tool holder (DVJNL 2020) – for VN-- 1604 indexable inserts, 93° approach geometry (Teknik Makina) The DVJN for VN-- 1604 Indexable Inserts is a left-hand turning toolholder engineered for secure clamping and consistent approach geometry in CNC and lathe operations. 93° approach geometry for reliable cutting Compatible with VN-- 1604 indexable inserts Overall length 125 mm for compact setups Secure clamping, 20 mm holder width Greater process security through defined approach geometry The holder provides a 93° cutting angle, which creates a controlled engagement between insert and workpiece. This geometry reduces radial loading and helps to stabilise the cut in left-hand turning operations, delivering more predictable tool life and surface finish. The combination of 40 mm cutting height and the defined approach assists in consistent chip evacuation, which is particularly useful in repetitive turning tasks where repeatability is critical. Repeatable clamping and compact design for efficient setup Designed with a 20 mm holder width and a 27 mm cutting-head width, the toolholder is balanced for compact tool stacks and easy access in confined turret stations. The ISO designation DVJNL 2020 denotes compatibility with common mounting standards, and the solid construction ensures secure clamping of VN--type inserts. With a weight of 0.428 kg, the unit is light enough to reduce turret inertia while remaining rigid for production use. Simple integration with existing tooling and inserts Compatibility with VN-- 1604 indexable inserts means standard insert stocks can be used without modification, lowering tooling variety and spare-part inventory. The shank/boring-bar reference K16 and overall length of 125 mm permit straightforward installation in many turning tool posts and turrets. The left-hand orientation is specified for counter-clockwise feed directions, ensuring correct tool geometry when combined with standard turning programmes. Reliability for everyday workshop and CNC use The construction focuses on durability and straightforward operation: robust clamping, standard ISO form, and compact dimensions support frequent insert changes and predictable maintenance intervals. The precise approach geometry contributes to consistent results across runs, reducing scrap and the need for rework. The holder is suitable for both manual lathe setups and automated CNC environments where dependable performance is required. Contact Metav Werkzeuge today for tailored advice on integrating the Teknik Makina DVJN tool holder into existing setups and to discuss delivery options from our Emmerich facility. Technical data Article number: D343TM Manufacturer: Teknik Makina Type designation: DVJNL 2020 Product name: DVJN for VN-- 1604 Indexable Inserts Facts Overall length: 125 mm Cutting height: 40 mm Holder height: 20 mm Cutting-head width: 27 mm Holder width: 20 mm Weight: 0.428 kg Cutting angle: 93° Special features Compatible with VN-- 1604 indexable inserts Left-hand cutting direction Shank/boring-bar designation: K16 ISO-compatible toolholder form DVJNL 2020 Designed for indexable turning applications FAQ Which insert type fits this holder? The DVJN tool holder accepts VN-- 1604 indexable inserts and is prepared for standard VN-- insert geometries used in turning operations. Is this holder intended for left-hand turning? Yes, the holder is specified for left-hand cutting direction and is intended for operations that require counter-clockwise feed orientation. What are the overall length and weight of the tool holder? The overall length is 125 mm and the weight is 0.428 kg, values that support compact turret mounting with lower inertia. What ISO or designation identifies the holder? This toolholder is designated DVJNL 2020, matching common ISO toolholder forms for indexable inserts. Which shank size or boring-bar reference is applicable? The holder references K16 for the shank/boring-bar designation to assist with selection of compatible tool posts and adaptors. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Benefit from a rigid right‑hand clamping system and precise compatibility with VCMT 1103 indexable inserts to ensure steady turning and repeatable results; order directly via Metav Werkzeuge or consult the specialists for application guidance. Klemmhalter — SVJC holder for VCMT indexable inserts, right‑hand, ISO SVJCR 2020 A Klemmhalter designed as a right‑hand turning holder for VCMT 1103 indexable inserts, ideal for standard external lathe operations where reliable clamping and repeatable geometry are required. Right‑hand turning orientation Compatible with VCMT 1103 inserts 20 mm shank for stable mounting 93° cutting angle for consistent cuts Predictable rigidity for repeatable turning The holder delivers a stable clamping platform that reduces deflection in repetitive turning tasks. With a 20 mm shank and a compact 125 mm overall length, the assembly is engineered to be sufficiently rigid while remaining easy to integrate into existing tool posts. The 93° cutting angle supports predictable chip flow and light cutting engagement, which in turn helps to maintain consistent surface finish and dimensional accuracy over longer production runs. Seamless integration with common indexable inserts Designed to accept VCMT 1103 plates, the holder follows the SVJCR 2020 ISO designation for compatibility with widely available inserts. This standardised interface enables quick plate replacement and reduces tooling complexity at the machine, allowing a smooth transition between jobs or grades of carbide without swapping tool bodies. The result is shorter changeover times and improved shop-floor efficiency. Geometry that supports machining quality and process control A 33 mm effective cutting height and the right‑hand orientation are combined in a layout that helps to keep the insert in the intended cutting plane, improving repeatability across multiple setups. The holder’s geometry is intended to favour predictable tool life under stable cutting conditions; as insert seating and clamping are consistent, variance in part results is minimised. The tool’s relatively low mass (0.378 kg) also contributes to controlled dynamic behaviour at typical lathe speeds. Practical advantages for workshop workflows The compact dimensions — 20 mm shank height and width with a 25 mm head width — make the holder suitable for tight setups where space is limited but accuracy must not be compromised. The right‑hand configuration meets common turning requirements and simplifies stocking of tool holders for routine operations. Reliability is supported by a straightforward design that focuses on essential functions: secure clamping, standard insert compatibility and a utilitarian footprint conducive to varied lathe applications. For application-specific recommendations or to secure a batch of Teknik Cutting Tools SVJCR 2020 holders, contact Metav Werkzeuge in Emmerich at info@metav-werkzeuge.com or +49 2822 7131930 for tailored advice and reliable supply coordination. Technical data Article number: D242TM Manufacturer: Teknik Makina Designation: Klemmhalter SVJC for VCMT Indexable Inserts ISO designation: SVJCR 2020 Facts Overall length: 125 mm Shank height: 20 mm Shank width: 20 mm Head width: 25 mm Cutting height: 33 mm Cutting angle: 93° Weight: 0.378 kg Special features For VCMT 1103 inserts Right‑hand orientation Bore designation: K11 Suitable for standard external turning FAQ Which insert type fits the holder? The holder is designed to accept VCMT 1103 indexable inserts; the interface complies with the SVJCR 2020 geometry specified for this class. Is the clamping direction left or right? This is a right‑hand tool holder; the right‑hand orientation ensures correct approach geometry for standard turning operations with VCMT 1103 plates. What are the shank dimensions and overall length? Shank dimensions are 20 mm × 20 mm with an overall length of 125 mm, giving the holder a compact profile suitable for constrained setups. How does the holder support machining repeatability? The holder’s fixed geometry, 93° cutting angle and secure seating for VCMT 1103 inserts contribute to repeatable cutting conditions and consistent part quality. What is the SKU and who is the manufacturer? The SKU is D242TM and the product is supplied by Teknik Makina under the designation SVJC for VCMT indexable inserts. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of a robust 125 mm cutting diameter and an 8‑edge design that delivers steady metal removal and consistent surface finish; compatibility with RPMW 1606 indexable inserts ensures fast reconditioning and predictable tool life. Order the cutter via Metav Werkzeuge or consult the technical team for precise selection and delivery. Indexable face mill T720TM – 125 mm diameter, 8‑edge cutter by Teknik Makina Indexable face mill T720TM is a heavy‑duty 125 mm cutter designed for face milling with RPMW 1606 indexable inserts, providing stable removal rates in general workshop and production applications 125 mm diameter for broad material removal 8 cutting edges for balanced surface finish 40 mm shank diameter for stable mounting Compatible with RPMW 1606 indexable inserts High‑efficiency material removal with consistent finishes The T720TM face mill combines a large 125 mm cutting diameter with a multi‑edge configuration to maintain cutting stability and reduce cycle times. The 8 cutting edges distribute cutting forces evenly, which minimises chatter and helps achieve a more uniform surface quality on the machined face. As a result, one benefit is improved productivity through higher material removal rates; a second is reduced rework due to the balanced cutting action. This design suits production environments where repeatable results and predictable tool behaviour are required. Secure insert retention for fast servicing Designed specifically for use with RPMW 1606 indexable inserts, the toolhead accepts widely available inserts from Korloy, enabling quick replacement and inventory flexibility. Insert clamping is assisted by a standard M5x12 screw and a T20 Torx key, which simplifies maintenance and shortens downtime during tool swaps. The tangible benefit is lower maintenance time per changeover; additionally, compatibility with established insert grades supports cost‑effective stocking strategies. Rigid mounting to reduce vibration and extend life A 40 mm shank diameter and a compact overall height of 63 mm provide a stable interface to the toolholder, improving concentricity and load transmission. Reduced vibration leads to longer insert life and fewer rebuilds, which directly supports sustained production runs. The mechanical stability also contributes to consistent dimensional control across batches, an important advantage for precision milling tasks where tolerance adherence is critical. Suitable roles and workflow integration This face mill integrates well into mixed production shops and machining centres that already use RPMW 1606 inserts and require a robust cutter for face milling or light profiling tasks. The combination of a broad cutting diameter, multiple cutting edges and common insert compatibility allows for streamlined tool management and easier process standardisation across machines. For buyers seeking interchangeability and an industrially proven clamping method, the tool represents a pragmatic choice. Contact Metav Werkzeuge today for tailored advice on integrating the T720TM face mill into production lines or to request stock information from Metav’s Emmerich facility via info@metav-werkzeuge.com or +49 2822 7131930 Technical Data SKU: T720TM Manufacturer: Teknik Makina ECLASS: 21180902 ETIM: EC011860 Core dimensions Diameter: 125 mm Overall height: 63 mm Cutting edges: 8 Shank diameter: 40 mm Features and compatibility For RPMW 1606 indexable inserts Torx key: T20 Screw: M5x12 Compatible inserts manufacturer: Korloy FAQ Which inserts fit this face mill? The T720TM accepts RPMW 1606 indexable inserts; Korloy‑brand RPMW 1606 grades are listed as compatible in the product data. What key sizes are required for insert changes? Insert fastening uses an M5x12 screw secured with a T20 Torx key for fast and standardised servicing. What is the shank diameter for mounting? The cutter has a 40 mm shank diameter, designed for stable clamping in appropriately rated toolholders. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of a robust, indexable-insert disc designed for efficient material removal and straightforward maintenance: the combination of a 125 mm diameter, a 40 mm arbor seat and compatibility with SCMT 1204 inserts ensures reliable chip formation and predictable tool life. Order the cutter directly via Metav Werkzeuge or consult our specialists for application advice. DF104TM disc milling cutter — 125 mm diameter, compatible with SCMT 1204 inserts (Teknik Makina) The DF104TM disc milling cutter is a heavy‑duty indexable‑insert cutter for productive face and shoulder milling, engineered for rigid mounting and fast insert changes *125 mm diameter for stable milling *Compatible with SCMT 1204 inserts *40 mm arbor seat for rigid mounting *T20 Torx screws M5x12 for secure clamp Precise machining through improved rigidity and balance A stable toolholder interface is vital for consistent surface quality; the 40 mm arbor seat and the cutter's disc geometry minimise deflection and vibration during cuts. The sizeable 125 mm diameter delivers a broad cutting arc that spreads cutting forces, which improves tool life and contributes to repeatable results in serial production. Emphasis on rigidity and balanced design reduces chatter, so operators benefit from fewer reworks and more predictable cycle times. Fast insert changes and secure clamping to maximise uptime The milling head is configured for indexable inserts of type SCMT 1204, allowing quick placings of fresh cutting edges without full tool regrinding. Fast, tool‑free insert replacement is supported by M5x12 Torx screws tightened with a T20 key, combining secure clamping with simple maintenance procedures. With 10 cutting edges and a 16 mm cutting height per insert position, the system reduces downtime and keeps the production flow moving with minimal intervention. Built for production: higher removal rates with controlled depth Designed for industrial use, the cutter permits an axial engagement of 32 mm, enabling higher material removal rates when paired with appropriate machining parameters. With a compact mass of 0.927 kg, the tool is straightforward to handle during set‑up while still providing the mass needed for stable rotation. The DF104TM integrates into standard milling stations and holders, offering predictable performance and straightforward inventory management for indexable insert tooling. For Teknik Cutting Tools DF104TM enquiries and rapid supply from our Emmerich facility, contact Metav Werkzeuge — Metav’s specialists will advise on holder compatibility and optimal cutting parameters Technical Data Article number: DF104TM Manufacturer: Teknik Makina Product designation: Disc milling cutter Compatible inserts: SCMT 1204 Torx screw: M5x12 Torx key: T20 Core technical figures Diameter: 125 mm Axial engagement (ap): 32 mm Arbor/seat diameter: 40 mm Cutting height: 16 mm Number of cutting edges: 10 Weight: 0.927 kg Special features Indexable‑insert concept for fast edge changes Secure clamping with Torx screws Designed for face and shoulder milling Balanced disc geometry for reduced vibration FAQ What inserts fit this cutter? The cutter accepts SCMT 1204 indexable inserts; the DF104TM is sized and pocketed for that insert type. Which arbor or holder is required? An arbor with a 40 mm seat is required for correct mounting and rigidity for this disc cutter. How many effective cutting edges are available? The cutter body provides 10 cutting edges in the standard configuration. What is the maximum axial engagement? The tool is specified with an axial engagement of 32 mm, enabling higher material removal in appropriate processes. Which screw and key are used for insert clamping? Insert clamping uses M5x12 Torx screws tightened with a T20 key. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of a compact, precision clamping solution that combines compact dimensions, a stable 90° cutting geometry and reliable compatibility with CCMT inserts to keep turning operations consistent and efficient; order directly via Metav Werkzeuge or consult our specialists for application-specific advice. Klemmhalter — SCACR-F turning holder for CCMT 09T3, right-hand, 20 × 20 mm (Teknik Makina) The Klemmhalter SCACR-F is a right-hand turning holder designed for external turning with CCMT 09T3 indexable inserts, suited to conventional and CNC lathes where compact, repeatable clamping is required Right-hand turning orientation Compatible with CCMT 09T3 inserts 20 x 20 mm head and shank 125 mm overall length, 0.42 kg weight Stable clamping for repeatable turning cycles The SCACR-F holder delivers rigid clamping and a consistent seating for indexable inserts, ensuring predictable tool behaviour during serial turning operations. With a 20 x 20 mm head and shank profile and a compact 125 mm overall length, the design reduces overhang and vibration, which supports surface finish consistency and longer insert life. The 90° cutting angle provides a straightforward geometry for facing and straight turning, while the modest mass of 0.42 kg contributes to quick spindle response on smaller lathes. Optimised for CCMT 09T3 inserts and workshop workflows Engineered specifically for CCMT 09T3 indexable inserts, the holder follows the ISO designation SCACR 2020, allowing simple matching with commonly stocked inserts and predictable indexing. The clamping concept prioritises quick insert changes and secure fixation, which reduces downtime during tool swaps and increases throughput. The clear designation and standardised mounting simplify integration into existing tool sets and tool turrets, helping maintain production rhythm in both single-piece and batch environments. Practical integration and maintenance in everyday use Compact dimensions and standard ISO form mean straightforward handling and storage in a busy workshop. The robust construction supports repeatable positioning and straightforward inspection; routine checks focus on the clamping screw and seating surface only, keeping maintenance effort minimal. For shops that require dependable, no-frills holders for standard CCMT inserts, this design offers a balance of precision, durability and ease of use that fits into typical turning operations without elaborate setup. For professional advice on integrating the SCACR-F turning holder into existing tool systems, or to secure reliable supply from Emmerich, contact Metav Werkzeuge — our specialists will advise on compatibility and delivery options via info@metav-werkzeuge.com or +49 2822 7131930 Technical Data SKU: D416TM Brand: Teknik Makina Article: SCACR-F for CCMT Indexable Inserts ISO designation: SCACR 2020 Core technical data Overall length: 125 mm Holder height: 20 mm Cutting head width: 20 mm Shank width: 20 mm Weight: 0.42 kg Cutting angle: 90° Special features For inserts: CCMT 09T3 Cutting direction: Right-hand ECLASS: 21181004 FAQ Which inserts are compatible with this holder? The holder accepts CCMT 09T3 indexable inserts; the SCACR-F geometry is matched to that insert size for reliable seating and indexing. Is the toolholder for left- or right-hand turning? This model is specified for right-hand turning applications, suited to standard right-hand cutting directions. What are the main dimensions and weight? Overall length is 125 mm, head and shank measure 20 x 20 mm, and the weight is 0.42 kg. What is the ISO designation of the holder? The holder is listed under SCACR 2020, the common ISO designation for this style of turning holder. Which production scenarios suit this holder best? The holder is ideal for lathe operations using CCMT 09T3 inserts where compact overhang, stable clamping and straightforward insert changes improve throughput. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Benefit from internal coolant and a precise fit for DCMT indexable inserts; the robust shank and a defined 32 mm cutting height deliver stable, repeatable turning results. Order the Klemmhalter SDJCL 2020 directly via Metav Werkzeuge or ask our consultants if needed. Klemmhalter SDJCL 2020 — Left‑hand toolholder with internal coolant (Teknik Makina) Klemmhalter SDJCL 2020 is a left‑hand toolholder for turning applications, designed for use with DCMT 11T3 indexable inserts and internal coolant supply Left‑hand cutting orientation Internal coolant supply For DCMT 11T3 indexable inserts ISO SDJCL 2020 designation Enhanced process stability through coolant delivery The integrated internal coolant channel ensures consistent lubrication and chip evacuation directly at the cutting edge, reducing heat and improving tool life. With a focused coolant feed, the holder supports longer uninterrupted runs and fewer tool changes, which contributes to higher machine uptime. This section highlights the holder’s capacity to maintain cutting conditions, rather than only listing dimensions, so production planners can expect more reliable cycle times and reduced rework. Accurate geometry for repeatable turning results Built to the ISO SDJCL 2020 profile, the clamping geometry offers a secure seat for DCMT 11T3 inserts and a repeatable insert position. The defined cutting height of 32 mm and a cutter head width of 25 mm guarantee consistent cutting geometry across batches. For work requiring tight tolerances, the stable insert clamping minimises deflection and supports predictable toolpath outcomes, which simplifies process qualification and shortens setup times. Compact design that fits workshop workflows With an overall length of 125 mm and a compact shank, the holder offers a balance between accessibility and rigidity in confined turret stations. The modest weight of 0.404 kg contributes to low centrifugal loads during high‑speed rotations while the left‑hand orientation and 93° cutting angle optimise chip flow for typical turning operations. The combination of compact size and solid construction supports flexible machine set‑ups and easier handling during indexable insert changes. Ready for integration and secure fastening Delivery features suitable fastening details for a fast fit on compatible tool posts: the holder accepts a Torx T15 drive and is secured with an M3,5x11 screw, while the U‑plate designation TA030 and toolbar rod reference K11 indicate common mounting interfaces. These attributes reduce adaptation effort when switching holders or integrating into existing turning stations, helping maintenance teams implement changes with minimal downtime. For reliable left‑hand turning with internal coolant, order the Teknik Makina SDJCL 2020 through Metav Werkzeuge — contact our team in Emmerich at info@metav-werkzeuge.com or +49 2822 7131930 for application advice Technical Data Article number: AP516TM Manufacturer: Teknik Makina Product designation: SDJC for DCMT Indexable Inserts ISO designation: SDJCL 2020 Facts Overall length: 125 mm Cutting height: 32 mm Holder height: 20 mm Head width: 25 mm Shank width: 20 mm Weight: 0.404 kg Cutting angle: 93° ECLASS: 21181004 Suitable inserts: DCMT 11T3 Screw: M3,5x11 Torx key: T15 Special features Internal coolant Left‑hand cutting direction U‑plate: TA030 Toolholder rod: K11 Designed for DCMT 11T3 indexable inserts FAQ Which insert types are compatible with this holder? The holder is designed for DCMT 11T3 indexable inserts; the SDJCL 2020 geometry ensures secure seating for these inserts on Teknik Makina holders (AP516TM) Is the coolant delivered to the cutting edge? Yes — the Klemmhalter SDJCL 2020 features internal coolant delivery that channels fluid directly to the insert area to improve cooling and chip control Can the holder be mounted on standard toolposts? Mounting uses common interfaces: the U‑plate designation TA030 and toolholder rod K11 align with many turret systems for straightforward installation What orientation is the holder made for? This toolholder has a left‑hand cutting orientation and a 93° cutting angle, optimised for left‑hand turning operations Which torque or driver is required for the clamping screw? The holder uses an M3,5x11 screw with a Torx T15 drive for clamping and insert fastening Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Compact right-hand boring bar with a 16 mm shank and compatibility for IR08 indexable inserts provides stable clamping and precise internal finishing. The 125 mm overall length and 7.8 mm cutting diameter make it suitable for small-bore machining tasks. Order the K337-2TM directly via Metav Werkzeuge or consult our specialists for application guidance. K337-2TM boring bar – 7.8 mm cutting diameter, 16 mm shank (Teknik Makina) The K337-2TM is a right-hand boring bar designed for internal turning with an SIR holder for IR indexable inserts, suitable for precision finishing and tight-reach operations Right-hand cutting direction Compatible with IR08 indexable inserts 16 mm shank for secure clamping 125 mm overall length for deep reach High-precision internal finishing with rigid support The combination of a 7.8 mm cutting diameter and 18 mm cutting height makes this boring bar a compact solution for accurate internal machining. The SIR holder specification (SIR S16K) and compatibility with IR08 indexable inserts ensure repeatable seating and predictable chip formation, which supports consistent bore quality over series production. With a 16 mm shank, the component offers improved resistance to deflection compared with smaller shanks, resulting in steadier cuts and reduced need for rework. These attributes translate into measurable process advantages for workshop operations that prioritise dimensional accuracy and surface finish. Fast insert changes and dependable clamping system Maintenance of cutting capability is simplified by a Torx-secured fastening system that uses a Torx T6 key and an M2x4.6 screw. This arrangement supports rapid indexable insert replacement and secure locking of the cutter, promoting short set-up times and reliable repeatability during shift work. The boring bar’s modest mass (0.195 kg) reduces inertia during rapid tool changes while remaining substantial enough to contribute to stable clamping during cut entry. The result is increased uptime and lower non-productive time for machining cells where quick tool swaps are routine. Practical advantages for small-bore and precision workshops With an overall length of 125 mm and a compact profile, the tool is engineered for confined spaces and internal operations on CNC lathes and turning centres. The right-hand cutting orientation and SIR holder system are well matched to finishing passes and light to medium internal turning, providing a balance between accessibility and cutting capacity. The K337-2TM’s specification supports modular tooling strategies: it integrates with existing SIR setups and IR insert stocks, enabling straightforward tool standardisation on the shop floor. Combined with consistent component labelling and dependable delivery from Metav Werkzeuge, this boring bar aids process standardisation and inventory rationalisation. Contact Metav Werkzeuge for availability and tailored recommendations for the Teknik Makina K337-2TM boring bar — our specialists in Emmerich provide application advice and reliable supply for precision tooling needs. Technical data Article number: K337-2TM Manufacturer: Teknik Makina ISO designation: SIR S16K Torx key: T6 Torx screw: M2x4.6 Suitable for: 8 IR indexable inserts Weight: 0.195 kg Key measurements Cutting diameter: 7.8 mm Cutting height: 18 mm Shank diameter: 16 mm Overall length: 125 mm Weight: 0.195 kg Features Right-hand cutting direction Compatible insert size: IR08 Holder designation: IR08 clamping holder Torx T6 screw fastening SIR system for indexable inserts FAQ Which insert type fits the boring bar? The K337-2TM uses IR08 indexable inserts in the SIR holder configuration; the holder is specified for 8 IR inserts. What are the main dimensions of the tool? Key measurements are a 7.8 mm cutting diameter, 18 mm cutting height, 16 mm shank diameter and 125 mm overall length. Which fastening hardware is required for insert clamping? Insert clamping is secured with a Torx T6 key and an M2x4.6 screw for reliable locking and quick replacement. Is the cutting direction left or right? The tool is manufactured for a right-hand cutting direction, suited to standard right-handed internal turning operations. How heavy is the boring bar and does it affect handling? The boring bar weighs 0.195 kg, providing a balance between manageable handling during tool changes and sufficient mass for stable clamping in the holder. Manufacturer / Responsible: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Strong clamping for RCMT 0803 indexable inserts combined with a compact 20 mm shank ensures stable turning and fast changeovers for batch and single-part production. Take advantage of the SRDCN 2020’s 125 mm overall length and neutral cutting direction for versatile workshop use; order directly via Metav Werkzeuge or ask our consultants if needed. SRDCN 2020 clamp holder — neutral cutting direction, for RCMT 0803 indexable inserts (Teknik Makina) The SRDCN 2020 is a clamp holder designed for RCMT 0803 indexable inserts, providing secure insert retention and compatibility with standard 20 mm shanks for a wide range of turning tasks. Designed for RCMT 0803 inserts Neutral cutting direction for versatile turning 20 mm shank width and height Total length 125 mm, robust construction Secure insert clamping for consistent turning results The SRDCN 2020 offers reliable insert retention that reduces vibration and improves surface finish during turning operations. Compatible with RCMT 0803 indexable inserts, the holder secures the cutting edge precisely to provide repeatable results across batches. The clamping geometry has been engineered for stability, which shortens set-up time and lowers scrap rates by keeping the insert position constant even under intermittent cutting loads, making the tool holder a practical choice for production and repair workshops alike. Compact dimensions that speed up set-up and handling With a total length of 125 mm and a shank dimension of 20 mm x 20 mm, this clamp holder is compact yet accessible for rapid tool changes and straightforward mounting. The cutting-head width of 10 mm and a cutting height of 37 mm mean the holder fits neatly into existing tool stations while maintaining adequate reach for most turning tasks. Compatibility with K08 boring-bar interfaces simplifies integration into standard tool systems, reducing inventory complexity and enabling quicker responses to production changes. Robust build for dependable workshop performance Manufactured to industry expectations, the holder’s design emphasises mechanical rigidity and straightforward serviceability for daily use. The neutral cutting direction makes the unit adaptable to both conventional and atypical turning scenarios, while the modest weight of 0.358 kg keeps handling safe and convenient during tool changes. Backed by Teknik Makina’s engineering and supplied through Metav’s quality-filtered distribution, the clamp holder supports continuous production with a focus on reliability and predictable performance. For expert advice on integrating the SRDCN 2020 clamp holder into workshop tooling systems, contact Metav Werkzeuge for tailored recommendations and reliable supply from Emmerich — info@metav-werkzeuge.com or +49 2822 7131930 Technical data SKU: D270TM GTIN: 4061905154065 Manufacturer: Teknik Makina Model: SRDCN 2020 Dimensions & weights Total length: 125 mm Shank width: 20 mm Shank height: 20 mm Cutting-head width: 10 mm Cutting height: 37 mm Weight: 0.358 kg Special features For RCMT 0803 indexable inserts Neutral cutting direction Compatible with K08 boring-bar designation Label: Klemmhalter SRDCN 2020 RCMT 0803 FAQ Which inserts fit this clamp holder? The holder accepts RCMT 0803 indexable inserts; the clamping seat and geometry are specified for this insert size on the SRDCN 2020 tool holder. Is the SRDCN 2020 suitable for both right- and left-hand turning? The SRDCN 2020 is specified for a neutral cutting direction, making it suitable for a wide variety of turning set-ups rather than being limited to a single hand. What are the mounting dimensions required for fitting the holder? Mounting requires a shank interface of 20 mm x 20 mm and a total available length of around 125 mm to accommodate the holder comfortably. Can the holder be used with standard boring bars? The holder is compatible with the K08 boring-bar designation, allowing straightforward integration into common tool systems. Who manufactures and distributes this tool? The tool is manufactured by Teknik Makina and distributed via Metav Werkzeuge; the product is listed under SKU D270TM (SRDCN 2020). Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of the combination of robust clamping, compact dimensions and simple servicing for uninterrupted parting and grooving operations; order the component directly via Metav Werkzeuge or ask their consultants for application advice. Parting clamp holder MGM 150 L125mm – right‑hand, 125 mm overall length, for MGM 150 indexable inserts (Teknik Makina) Parting clamp holder MGM 150 L125mm is a precision clamp holder designed for right‑hand parting and grooving applications, compatible with MGM 150 indexable inserts and optimised for compact lathe tool posts. Compatible with MGM 150 indexable inserts 125 mm overall length for compact setups Max grooving depth 14 mm Right‑hand orientation for standard turning Built for secure, vibration‑resistant cutting The clamp body delivers consistent rigidity through its compact 12 x 12 mm section and a 125 mm overall length, which helps to reduce chatter during cut‑off and grooving operations. The rigid design improves tool life and surface finish by keeping the insert in a stable position; indexable inserts can therefore be used to their full life, lowering tooling costs per component. The short, stiff geometry also eases setup in small tool posts without sacrificing cutting stability. Fast insert changes and reliable clamping to cut downtime A simple clamping concept with an M5x16 clamping screw permits quick insert replacement and secure retention of the cutting tip. The assembly uses a 4 Allen key for tightening, enabling rapid interventions at the machine and reducing non-productive time. With a maximum grooving depth of 14 mm and a cutting width of 1.5 mm, the holder is suitable for precise parting and narrow‑groove operations where repeatable clamping force is essential for consistent cycle times. Compact form factor that fits tight setups The 12 mm section and 12 mm cutting head width make the holder particularly suitable for compact tool posts and multi‑tool turrets where space is at a premium. The right‑hand cutting orientation is matched to standard turning directions and facilitates straightforward insertion into existing turret stations. The ISO designation 1212 identifies the holder interface and simplifies integration into tool lists and assembly drawings. Practical compatibility and clear specification for workshop planning Marked compatibility with MGM 150 inserts and proven fit for Korloy insert variants streamlines inventory management and procurement decisions. The ISO designation and the clear dimensional data (125 mm overall length, 12 mm clamp width/height, 1.5 mm cut width) support planning for set‑ups and fixture design, enabling predictable tool performance and fewer trial cuts during process development. Contact Metav Werkzeuge to arrange supply of this Teknik Makina parting clamp holder (SKU D651TM) and to receive tailored mounting guidance and stock availability from the Emmerich team Technical data SKU: D651TM Label: Stechklemmhalter MGM 150 L125mm Manufacturer: Teknik Makina eClass: 21181005 Facts Overall length: 125 mm Clamp width: 12 mm Clamp height: 12 mm Cutting head width: 12 mm Cutting width: 1.5 mm Max grooving depth: 14 mm Screw: M5x16 ISO designation: 1212 Direction: right Materials & compatibility Compatible with MGM 150 indexable inserts Suitable for Korloy inserts Allen key size: 4 Allen FAQ Which inserts are compatible with this clamp holder? The holder accepts MGM 150 indexable inserts; Korloy‑branded MGM 150 types are listed as compatible for straightforward procurement. What is the maximum grooving depth achievable? The maximum grooving depth is 14 mm, allowing the holder to perform standard parting and narrow‑groove tasks reliably. Which fastening hardware is required for insert changes? Insert clamping is achieved with an M5x16 screw and a 4 Allen key, enabling quick and repeatable insert changes. Is the holder suitable for small tool posts and turrets? Yes; the compact 12 x 12 mm cross‑section and 125 mm overall length make it suitable for confined tool posts and multi‑tool turrets. What cutting width does the holder support? The nominal cutting width is 1.5 mm, appropriate for fine grooving and precise parting operations. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Combine robust clamping with a compact 125 mm overall length and precise left-hand cutting to ensure reliable grooving operations. Order the grooving clamp holder directly via Metav Werkzeuge or consult our specialists for application advice. Grooving clamp holder for MGMN 300 indexable inserts — 125 mm, left-hand (Teknik Makina) Grooving clamp holder for MGMN 300 indexable inserts, engineered for compact setups and repeatable left-hand grooving operations For MGMN 300 indexable inserts Left-hand cutting orientation 125 mm overall length for compact setups Precise clamping for repeatable grooving results The grooving clamp holder is engineered to secure MGMN 300 indexable inserts with high rigidity, providing consistent tool positioning across repeated cycles. The clamping width 16 mm and ISO designation 1616 define a compact shank geometry that reduces deflection during grooving and cut-off operations. For manufacturers and job shops that require predictable component tolerances, the combination of a stable holder and standardised insert format helps to maintain surface finish and dimensional accuracy while minimising rework. Fast insert changes and secure fixation reduce downtime Designed for straightforward maintenance, the holder uses an M4x12.5 Torx screw and a T15 key for positive insert clamping, enabling quick indexable insert replacement and short tool-change intervals. The cutting width 3 mm and a maximum grooving depth of 16 mm allow controlled material removal in narrow grooves, while the cutting head width 16.3 mm gives clearance for chip flow and coolant access where applicable. Compatibility with Korloy-manufactured inserts broadens sourcing options and supports efficient inventory management for production environments. Compact left-hand design suited to restricted toolposts With a 125 mm overall length and a tool weight of approximately 0.267 kg, this holder is well suited to tight setups where overhang must be kept to a minimum. The left-hand orientation supports specific turning and grooving programmes and is beneficial where toolpath geometry or machine configuration demands a left-hand approach. For applications in small-batch production or repair work, the compact dimensions and standardised interface translate into easier handling, reduced vibration and improved repeatability on parts requiring narrow grooves. For reliable left-hand grooving choose the Teknik Cutting Tools holder and get tailored advice or place orders through Metav Werkzeuge — contact info@metav-werkzeuge.com or call +49 2822 7131930 for detailed specification support Technical data SKU: D057TM Label: Grooving clamp holder MGMN 300 L125mm Product type: Grooving clamp holder Manufacturer: Teknik Makina Facts Overall length: 125 mm Weight: 0.267 kg Clamp width: 16 mm Holder height: 16 mm Cutting head width: 16.3 mm Cutting width: 3 mm Max grooving depth: 16 mm ISO designation: 1616 Special features Compatible with MGMN 300 inserts Compatible insert manufacturer: Korloy Cutting direction: left Torx screw: M4x12.5 Torx key: T15 FAQ What insert type fits this holder? The grooving clamp holder accepts MGMN 300 indexable inserts, specified for narrow-grooving and cut-off tasks in this holder. Is the holder compatible with Korloy inserts? Yes, the holder is compatible with Korloy-manufactured inserts; the design supports standard MGMN 300 geometries. Which screw and key are required for clamping? Clamping is secured with an M4x12.5 Torx screw, tightened using a T15 Torx key for reliable fixation. What is the maximum grooving depth? The holder allows a maximum grooving depth of 16 mm, suitable for many narrow-groove applications. Is this a left-hand or right-hand holder? This is a left-hand grooving clamp holder (SKU D057TM), designed for left-hand cutting orientations. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of a compact, compatibility-focused solution that combines reliable clamping, precise parting capability and straightforward installation. The holder’s 16 x 16 mm shank and 125 mm overall length deliver consistent set-up on standard toolposts while compatibility with MGMN 200 indexable inserts ensures predictable machining results — order or consult Metav Werkzeuge for assistance. Parting toolholder for MGMN 200 — left-hand, 125 mm by Teknik Makina A parting toolholder for MGMN 200 indexable inserts engineered for left-hand parting operations in turning applications, designed to fit standard 16 x 16 mm toolposts. Compatible with MGMN 200 indexable inserts Left-hand parting for lathe operations Shank size 16 x 16 mm (ISO 1616) Max parting depth 16 mm Precision clamping for repeatable parting results The holder is built to provide a secure clamp for MGMN 200 style inserts, which are commonly used for narrow parting and grooving tasks. Thanks to the 16 x 16 mm shank (ISO 1616) and a compact head width of 16.2 mm, the device delivers a stable tool position that reduces deflection during cut-off. The left-hand orientation and 2 mm cutting width specification make it suitable for controlled, narrow groove machining. These features translate directly into fewer rejects and a steadier process when fitting the tool to a compatible toolpost. Faster setup, clear compatibility and reliable fixation Setup is simplified by the standard ISO 1616 clamping geometry and the Torx fixation system. The toolholder uses a Torx T15 key and an M4x12.5 Torx screw for secure insert retention, which speeds changeovers and lowers downtime. A modest mass of 0.267 kg keeps balance on the turret without adding unnecessary inertia, while the 125 mm overall length offers good reach for most lathes without compromising rigidity. The combination of standardised interfaces and robust fastening yields measurable time savings in repetitive production tasks. Application guidance and material suitability This holder is matched to MGMN 200 inserts from established manufacturers such as Korloy, making it a pragmatic choice for general parting and grooving in a range of ferrous and non-ferrous turning operations. The maximum parting depth of 16 mm and narrow 2 mm cutting width are intended for precise cut-off work rather than heavy-duty roughing; they are best employed where dimensional control and minimal material waste are priorities. The compact head profile supports access to confined geometries while maintaining a stable clamping arrangement. For availability, technical clarification or to source the Teknik Makina parting toolholder D055TM directly from Metav Werkzeuge, contact Metav Werkzeuge via info@metav-werkzeuge.com or call +49 2822 7131930 for prompt assistance and ordering guidance Technical data SKU: D055TM Product: Parting toolholder for MGMN 200 indexable inserts Brand: Teknik Makina Facts Overall length: 125 mm Weight: 0.267 kg Shank width x height: 16 x 16 mm (ISO 1616) Cutting head width: 16.2 mm Max parting depth: 16 mm Cutting width: 2 mm Direction: left Torx key: T15 Torx screw: M4x12.5 Special features Compatible with MGMN 200 indexable inserts Compatible insert manufacturer: Korloy Clamp-type insert holder ISO designation: 1616 Compact head for restricted access FAQ Which inserts fit this parting toolholder? The parting toolholder is designed for MGMN 200 indexable inserts; compatible grades from Korloy are commonly used with the holder D055TM. What is the maximum cutting depth for this holder? The maximum parting depth for the holder is 16 mm, suitable for controlled cut-off operations where depth is limited by the insert geometry. Which shank size is required on the turret? This holder requires a 16 x 16 mm toolpost or turret slot (ISO 1616) to ensure correct seating and clamping. How is the insert fastened in the holder? Insert retention is achieved with a Torx screw specification M4x12.5, tightened with a T15 Torx key to provide secure fixation and quick insert changes. Is this holder suitable for heavy roughing? The holder is optimised for precise parting and grooving with a 2 mm cutting width and is not intended as a heavy-duty roughing tool; it is best applied where dimensional control and minimal clearance are required. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Combining a 16 x 16 mm shank, 125 mm overall length and compatibility with MGM 150 indexable inserts, this grooving clamp holder delivers secure clamping and repeatable groove geometry for routine production. Benefit from a narrow 1.5 mm cutting width and a maximum 14 mm grooving depth to handle precision parting and grooving tasks. Order the holder directly via Metav Werkzeuge or ask our consultants if needed. Grooving clamp holder MGM 150 L125mm – 16 x 16 mm shank, 125 mm overall length (Teknik Makina) The Grooving clamp holder MGM 150 L125mm is a right-hand grooving and parting clamp holder intended for use with MGM 150 indexable inserts, designed to provide a compact, rigid mounting solution for workshop lathes and small turning centres. *Stable 16 x 16 mm shank for secure mounting *125 mm overall length for deep reach *Compatible with MGM 150 indexable inserts *Right-hand cutting with 1.5 mm cutting width Secure mounting that improves edge consistency The holder’s 16 x 16 mm shank and ISO 1616 designation ensure a compact, stable interface with the tool post, reducing deflection during cutting. This rigidity contributes directly to consistent edge quality and longer insert life, particularly when working in narrow grooves. By fixing the insert with a robust M5x16 clamping screw and a 4 mm Allen key, the assembly minimises micro-movements that can cause chatter; the result is repeatable parting and groove profiles with fewer rejects and less rework. Efficient right-hand grooving for controlled chip formation Designed for right-hand cutting operations, the clamp holder supports a 1.5 mm cut width and a maximum grooving depth of 14 mm, making it suitable for fine parting and medium-depth grooving tasks. The compact cutting head width of 16 mm accommodates tight toolpaths while maintaining chip control. These measurable characteristics translate into practical production benefits: faster cycle times, predictable cutting forces and reduced setup adjustments when switching between similar jobs. Quick insert interchange and compatibility with standard inserts Compatibility with MGM 150 indexable inserts and recognised insert manufacturers such as Korloy simplifies purchasing and tool management. The clamping concept allows straightforward insert replacement without special fixtures, reducing machine downtime. For workshops managing multiple tool holders, this modular approach supports lean tooling strategies and keeps tool inventories standardised while preserving cutting performance. Built for small-batch flexibility and series production alike Whether used in single-machine workshops or integrated into a larger cell, this clamp holder balances accessibility with industrial robustness. The overall 125 mm length provides the reach needed for deeper grooves while the narrow cutting geometry supports high-precision finishes. For production planners, the holder offers a dependable option to maintain throughput without complex adjustments, supporting a predictable machining workflow and lower scrap rates. For reliable right-hand grooving choose Teknik Makina’s grooving clamp holder and contact Metav Werkzeuge in Emmerich for expert advice or to secure immediate supply from our European warehouse. Technical data Article number: D652TM Manufacturer: Teknik Makina Product type: Grooving clamp holder Compatibility: MGM 150 indexable inserts Compatible insert manufacturer: Korloy Facts Overall length: 125 mm Shank dimensions: 16 x 16 mm Cutting width: 1.5 mm Maximum grooving depth: 14 mm Cutting direction: right Clamping screw: M5x16 Allen key: 4 mm Special features ISO designation: 1616 Cutting head width: 16 mm SKU: D652TM Right-hand grooving configuration FAQ Which inserts fit this clamp holder? The holder is designed for MGM 150 indexable inserts and is compatible with inserts from manufacturers such as Korloy; the interface follows the MGM 150 geometry. What is the maximum groove depth achievable? The maximum grooving depth for this clamp holder is 14 mm, enabling medium-depth parting and grooving operations within that limit. What shank size is required for the tool post? The clamp holder uses a 16 x 16 mm shank, providing a compact and stable mounting for standard tool posts that accept 16 mm shanks. How is the insert secured in the holder? An M5x16 clamping screw secures the insert, tightened with a 4 mm Allen key to ensure firm clamping and minimal vibration during cutting. Is the holder suitable for left-hand cutting or only right-hand? This specific configuration is set up for right-hand cutting; left-hand operations would require a corresponding left-hand holder. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Reliable right-hand parting with ISO 1212 compatibility and a compact 12 mm profile delivers repeatable, low-vibration cuts; benefit from a maximum 16 mm cutting depth and secure clamping for efficient parting operations — order or request application advice via Metav Werkzeuge. Stechklemmhalter — Right-hand parting and grooving holder with ISO 1212 seat (Teknik Makina) The Stechklemmhalter is a right-hand parting and grooving holder designed for use with 2C DGN indexable inserts, offering a compact footprint for precision metalcutting tasks. Right-hand cutting direction Compatible with ISCAR 2C DGN inserts Max cutting depth 16 mm Compact 12 mm shank height Reliable, repeatable parting for production environments The compact toolholder delivers consistent parting accuracy by combining a precision ISO seat with a secure clamping concept. The ISO 1212 datum and the 2C DGN insert interface ensure correct positioning of the insert, which reduces setup variation and shortens cycle-to-cycle deviation. For production workshops this translates into fewer rejects and a more predictable process, since correct insert seating directly affects cut geometry and tool life. Reduced vibration and improved finish through compact design A small cross-section and modest mass contribute to a stable machining setup. With a shank and head width of 12 mm and a weight of 0.158 kg, the holder reduces overhang and helps to dampen chatter during parting and narrow-groove operations. The reduced vibration improves surface finish and extends insert life, which lowers tooling costs over many runs — particularly on automated lathes and bar-feed machines where repeatability is essential. Designed for efficient integration and easy mounting The holder accepts indexable inserts in the 2C DGN format and mates with a bore designated 2C-R DGN, simplifying tool assembly and replacement. A maximum cutting depth of 16 mm permits deeper parting where required while the narrow 2 mm insert cutting edge supports fine-detail cuts. The right-hand cutting direction and ISO-compliant interface mean fast retrofitting into existing tool posts and straightforward interchangeability across similar setups. For precision parting and grooving solutions, choose Teknik Makina’s Stechklemmhalter and contact Metav Werkzeuge for application guidance and reliable supply — eMail: info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: D750TM Manufacturer: Teknik Makina Product name: Stechklemmhalter Compatible inserts: 2C DGN (ISCAR) Facts Shank height: 12 mm Cutting-head width: 12 mm Overall width: 12 mm Insert cutting width: 2 mm Max cutting depth: 16 mm Overall length: 125 mm Weight: 0.158 kg Cutting direction: right Special features ISO designation: 1212 Toolholder bore: 2C-R DGN Suitable for indexable inserts: 2C DGN Files included: 2 attachments FAQ Which inserts fit this holder most effectively? The holder is configured for 2C DGN indexable inserts and is compatible with inserts from ISCAR; the ISO 1212 seat secures correct positioning for reliable cutting. What is the maximum parting depth achievable? The maximum recommended cutting depth is 16 mm, allowing for deeper parting and grooving when process parameters are set accordingly. Is this holder for right- or left-hand cutting? This design is a right-hand parting and grooving holder; the cutting direction is configured for conventional right-hand toolpaths. What are the key dimensions and weight? Key dimensions include a 12 mm shank/head width, 125 mm overall length and a mass of 0.158 kg, offering a compact, low-overhang solution. How does the holder improve tool life and surface finish? The compact 12 mm profile and accurate ISO seating reduce tool overhang and vibration, which improves surface finish and extends insert life in repetitive parting operations. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Reliable parting performance with a 4 mm cutting width and a 20 x 20 mm shank delivers consistent cycle times and reduced scrap; compatibility with Sandvik inserts simplifies inventory. Order the holder directly via Metav Werkzeuge or request application advice from their consultants. Stechklemmhalter D908TM — Right‑hand parting and grooving tool holder with 20 x 20 mm shank A Stechklemmhalter D908TM designed for right‑hand parting and grooving in lathe operations, offering a compact 125 mm overall length for workshop use Right‑hand cutting direction 20 x 20 mm shank (ISO 2020) Compatible with Sandvik inserts Max parting depth 18 mm Precise parting that reduces rework and cycle time The holder is engineered for repeatable parting operations: the 4 mm cutting width and 18 mm maximum parting depth provide a balance between material removal and tool life, making it suitable for short to medium series production. As a right‑hand cutting tool holder, it is intended for conventional turning set‑ups where controlled chip formation and predictable forces are essential. The combination of cut geometry and clamping stability helps to reduce vibrations and minimise rework, supporting efficient shopfloor throughput. Standardised interface for fast changeovers Aided by a 20 x 20 mm shank and the ISO 2020 designation, the holder fits common tool posts and quick‑change systems, allowing easy integration into existing setups. Compatibility with Sandvik‑compatible indexable inserts keeps tooling inventories lean and reduces downtime during changeovers. The internal designation shown as 4C‑123 SDV‑R clarifies the holder family and mounting style for planners and tooling managers, ensuring straightforward procurement and replacement planning. Compact, robust build for everyday workshop demands With an overall length of 125 mm and a mass of 0.415 kg, the holder combines a compact footprint with sufficient rigidity for typical parting and grooving tasks. The 20 mm head width and 20 mm shank height contribute to secure clamping and predictable cutting forces, which supports longer insert life and consistent surface quality. Designed for pragmatic workshop use, the construction helps to maintain stable cutting conditions across repeated cycles and varied batches, thus supporting dependable production planning. For precision parting tasks, select the Teknik Makina holder and contact Metav Werkzeuge for tailored application advice or to arrange supply directly through their Emmerich service team Technical Data Article number: D908TM Manufacturer: Teknik Makina Overall length: 125 mm Weight: 0.415 kg Core dimensions Shank height: 20 mm Shank width: 20 mm Cutting head width: 20 mm Cutting width: 4 mm Max parting depth: 18 mm Cutting direction: Right‑hand Compatibility and designation ISO shank designation: 2020 Compatible with Sandvik inserts Toolholder designation: 4C-123 SDV-R FAQ What materials is this holder suitable for? The Stechklemmhalter D908TM is intended for general turning and parting tasks; material suitability depends on the chosen insert grade, with the holder compatible with Sandvik inserts to cover a wide range of steels and non‑ferrous materials. Which shank and mounting standards does the holder follow? The toolholder uses a 20 x 20 mm shank in the ISO 2020 format and the internal designation 4C‑123 SDV‑R clarifies the mounting family for workshop planners. Can the D908TM be used with standard Sandvik indexable inserts? Yes, the holder is Sandvik‑compatible, enabling the use of common insert geometries and grades to match the cutting application and material. What is the maximum parting depth achievable with this holder? The maximum recommended parting depth for the D908TM is 18 mm, which balances effective chip evacuation and mechanical rigidity for most parting operations. Is the D908TM suitable for high‑volume production? The holder is designed for reliable, repetitive parting tasks; combined with appropriate insert selection and process control, it supports stable throughput in small to medium production runs. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of the combination of compact dimensions, precise parting capability and broad insert compatibility for reliable, repeatable parting operations; order directly via Metav Werkzeuge or ask for technical advice to ensure the holder meets specific machining needs. Parting clamp holder — 20 x 20 mm shank, for Korloy 2C KGMN inserts (Teknik Makina) Parting clamp holder designed for precision parting and grooving operations in general turning applications, compatible with Korloy 2C KGMN indexable inserts. 20 x 20 mm square shank Compatible with Korloy 2C KGMN inserts 2 mm cutting width for accurate parting 125 mm overall length for stable setup Precise parting where consistency matters The 20 x 20 mm shank and compact overall length of 125 mm deliver a stable, low-vibration tool setup that supports repeatable parting cycles. With a cutting width of 2 mm and a maximum plunge depth of 3.5 mm, the holder is engineered for controlled material separation and narrow-groove machining, reducing rework and scrap. The neutral cutting direction provides flexibility for a range of turning centres and lathe orientations, which helps maintain cycle time consistency across different components. Secure clamping and robust geometry for repeatable results A clamping head width of 23.5 mm and a secure insert pocket ensure firm seating of indexable inserts, so cutting forces are transmitted reliably into the tool body. The nominal tool mass (0.412 kg) contributes to a balanced feel during setup while still damping chatter on shorter overhangs. The ISO shank designation 2020 relates directly to the toolholder geometry, simplifying selection when matching turret pockets or toolpost adapters on standard machine interfaces. Broad compatibility to simplify tooling inventory Designed for use with the Korloy insert family 2C KGMN, the toolholder accepts the commonly used insert format for parting/grooving, allowing straightforward replacement and quick reconditioning. The holder’s specification line reference 2C KGEVR-KGMN indicates the compatible bar and insert combinations, enabling rapid sourcing of spare inserts and reducing machine downtime. Choosing a holder compatible with established insert types streamlines procurement and inventory management in the workshop. Practical benefits for workshop workflows By combining a compact shank, secure clamping and a narrow cutting width, the toolholder supports precision finishing passes and controlled parting operations that contribute to higher first-pass yields. The neutral cutting direction enhances adaptability across setups and the straightforward geometry reduces the need for special fixturing. For teams aiming to maintain throughput without sacrificing surface quality, this holder offers a pragmatic balance between rigidity and versatility. For technical guidance on integrating this Teknik Makina parting clamp holder into production workflows, contact Metav Werkzeuge for tailored advice and prompt supply: email info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: D622TM Manufacturer: Teknik Makina Designation: Parting clamp holder Facts Shank width: 20 mm Shank height: 20 mm Cutting head width: 23.5 mm Cutting width: 2 mm Max plunge depth: 3.5 mm Overall length: 125 mm Diameter: 120 Weight: 0.412 kg Cutting direction: neutral Special features Compatible with Korloy 2C KGMN inserts ISO shank designation: 2020 Bar reference: 2C KGEVR-KGMN Compact design for reduced vibration FAQ Which inserts fit this holder? The holder is specified for Korloy 2C KGMN indexable inserts; the bar reference 2C KGEVR-KGMN indicates compatible insert/bar pairings. What are the key dimensions to check for turret fitment? Relevant dimensions are the 20 x 20 mm shank, overall length 125 mm and cutting head width 23.5 mm to ensure correct seating and clearance in standard tool posts. What maximum cutting depth can be achieved? The toolholder supports a maximum plunge depth of 3.5 mm, suitable for narrow parting and groove operations that require tight control. Is the cutting direction fixed or variable? The holder is specified with a neutral cutting direction, giving flexibility for different lathe orientations and standard parting setups. How does the toolholder assist in reducing scrap and rework? By providing a stable shank and precise 2 mm cutting width, the holder enables controlled parting with reduced deflection, which improves first-pass success and decreases the need for corrective machining. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Benefit from a compact, rigid design that combines a 12 mm head, a 2 mm cutting width and a precise right-hand cutting orientation to deliver consistent narrow-grooving results. Order supply via Metav Werkzeuge or consult their advisors for application matching and prompt delivery. Parting Tool Holder D718TM by Teknik Makina — 12 mm head, right-hand The Parting Tool Holder D718TM is a right-hand parting and grooving clamping holder designed for indexable inserts and short overhang turning tasks, offering secure clamping and narrow-groove capability in workshop and production environments. 12 mm head width and height 2 mm cutting width for narrow grooves Right-hand cutting orientation Compatible with Taegutec 3C TD inserts Consistent, narrow-grooving performance for production turning The D718TM holder delivers repeatable results thanks to its 2 mm cutting width and a maximum plunge depth of 16 mm, which together allow efficient parting and fine-grooving with minimal rework. The 12 mm head provides a short tool overhang and increased rigidity, reducing vibration and improving surface finish when used with indexable inserts. Compatibility with Taegutec 3C TD grades ensures a broad choice of chipbreakers and edge designs; ISO 1212 designation clarifies the seat and geometry for correct insert seating. In practice, this combination reduces cycle time by keeping tool deflection low and chip control predictable. Fast set-up and secure clamping keep machines productive The holder’s clamping arrangement, matched to the 3C-R TD bar designation, allows straightforward insert seating and positive clamping, which shortens setup intervals on lathes and turning centres. With an overall length of 125 mm and a mass of 0.16 kg, the tool balances accessibility and stability for typical toolpost or turret mounts. Secure clamping minimises insert movement under cutting forces, lowering tool-change frequency and improving first-pass yield. For shops transitioning between batch sizes, the reduced downtime associated with quick clamping and standardised insert interfaces translates directly into higher throughput. Versatile workshop use and assurance from a trusted supplier Designed for narrow parting and grooving tasks, the holder suits toolrooms and industrial workshops that require precision on small diameters or where space on the turret is limited. The D718TM supports standard 3C TD indexable inserts from Taegutec, which are available in a range of grades for steel, stainless materials and other alloys; this makes the holder a pragmatic choice for mixed-production environments. Metav’s presence in Emmerich acts as a local supply and quality filter: with a broad product range and longstanding customer trust, the distributor simplifies procurement and ensures consistent availability for routine and special orders. Choose the Teknik Cutting Tools Parting Tool Holder D718TM for reliable narrow-grooving performance and arrange supply or technical advice through Metav Werkzeuge in Emmerich at info@metav-werkzeuge.com or +49 2822 7131930 Technical data SKU: D718TM Manufacturer: Teknik Makina Article designation ISO: 1212 Cutting direction: right Compatible insert manufacturer: Taegutec Compatible insert type: 3C TD Clamping bar designation: 3C-R TD Facts Overall length: 125 mm Head width: 12 mm Head height: 12 mm Cutting width: 2 mm Maximum plunge depth: 16 mm Weight: 0.16 kg Special features Right-hand cutting orientation Compatible with Taegutec 3C TD indexable inserts ISO 1212 seating geometry Clamping bar designation 3C-R TD Intended for parting and narrow grooving FAQ Which inserts fit this holder? The Parting Tool Holder D718TM is compatible with Taegutec 3C TD indexable inserts; the holder uses the ISO 1212 seating for correct fit. Is the tool suitable for left-hand cutting? The holder is manufactured for right-hand cutting only; left-hand orientation is not supported by this model. What is the maximum plunge depth for grooving operations? Maximum plunge depth is 16 mm, suitable for many narrow parting and grooving applications. How should the holder be mounted in a turret or toolpost? Mount using the standard 3C-R TD clamping bar interface and ensure secure seating of the insert in the ISO 1212 pocket before cutting. For which workshop tasks is this holder recommended? Recommended for narrow parting, precision grooving and short-overhang turning where a 2 mm groove width and stable clamping are required. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Benefit from a compact, rigid design that combines a 16×16 mm shank, a 2 mm cutting width and a 125 mm overall length for accurate, low-vibration parting and grooving. Order the D715TM parting tool holder directly via Metav Werkzeuge or consult the Metav advisors for application guidance. Parting Tool Holder D715TM — right‑hand, 16×16 mm shank (Teknik Makina) The Parting Tool Holder D715TM is a right‑hand grooving and parting holder with an ISO 1616 16×16 mm shank, engineered for stable clamping and precise short‑run parting when used with compatible indexable inserts. Right-hand cutting direction 16×16 mm shank ISO 1616 2 mm cutting width for narrow grooves 125 mm overall length for extended reach Stable clamping for repeatable parting operations The square 16×16 mm shank and ISO designation ensure a secure fit in standard toolposts, reducing movement under load and improving repeatability. A compact overall length of 125 mm maintains stiffness close to the workpiece, helping to limit deflection during the cut. With a mass of 0.27 kg, the holder contributes little to the tool assembly inertia while still providing the rigidity expected in machining centres and lathes. These characteristics translate directly into more consistent parting quality and fewer rejects in serial turning tasks. Narrow‑width cutting for fine groove and parting tasks A 2 mm cutting width enables confined grooving and fine parting where material saving and tight tolerances matter. The holder accepts standard short‑type inserts for narrow cuts, allowing shops to keep a reduced inventory while maintaining flexibility across jobs. The right‑hand cutting orientation is suited to conventional lathe setups and supports controlled chip formation when paired with the correct insert geometry, promoting cleaner shoulders and reduced rework in delicate components. Practical depth and compatibility for everyday workshop use The toolholder supports a maximum parting depth of 16 mm, covering most small- to medium‑diameter parting applications. Compatibility with Taegutec inserts (designation 2C TD, and bar designation 2C‑R TD) simplifies tool sourcing and changeovers, as these are common industry standards for grooving and parting inserts. The ISO 1616 profile means straightforward integration into tool posts sized for 16 mm square holders, minimising setup time and supporting efficient production cycles. Workshop integration and trusted supply chain Designed for routine use in production and jobbing shops, this holder balances accessibility with industrial performance. Sourcing the product through Metav Werkzeuge provides the added assurance of a European supply hub that acts as a quality filter: consolidated stock, technical advice and consistent availability from Emmerich. For operations seeking dependable, simple-to-specify holders that work with widely available inserts, this toolholder supports reduced logistics overhead and faster turnaround between jobs. For technical advice or to secure delivery of the Teknik Makina D715TM, contact Metav Werkzeuge for personalised consultation and reliable supply from Emmerich. Technical Data Article number: D715TM Manufacturer: Teknik Makina Facts Overall length: 125 mm Shank: 16 × 16 mm (ISO 1616) Cutting width: 2 mm Maximum parting depth: 16 mm Weight: 0.27 kg Special features Cutting direction: right Compatible with Taegutec inserts (2C TD) Bar designation: 2C‑R TD FAQ Which inserts fit this holder? The holder is compatible with Taegutec indexable inserts specified as 2C TD; the matching bar designation is 2C‑R TD for correct seating and clamping. What is the shank size and standard? The shank is 16 × 16 mm and conforms to ISO 1616, enabling fitting into toolposts designed for 16 mm square holders. How deep can this holder part? The maximum parting depth is 16 mm, suitable for many small- and medium-diameter parting operations. Is the cutting direction left‑hand or right‑hand? This toolholder is configured for right‑hand cutting direction. What is the total length and why does it matter? The overall length is 125 mm; a shorter, stiff assembly helps reduce deflection and improve surface finish during parting. How heavy is the holder? The toolholder weighs 0.27 kg, contributing modestly to the overall tool assembly inertia. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Benefit from precise parting performance thanks to the combination of a 2 mm cutting width and a 20 × 20 mm holder profile for stable clamping and predictable chip control. The right‑hand orientation and a maximum parting depth of 18 mm deliver dependable results in compact set-ups; order directly via Metav Werkzeuge or consult our specialists for process guidance. Parting-off clamping holder D701TM — Right‑hand parting tool holder, 20×20 mm body (Teknik Makina) A Parting-off clamping holder D701TM designed for right‑hand lathe applications, intended for narrow groove and parting operations with Horn indexable inserts Right-hand tool for standard parting operations 2 mm cutting width for narrow grooves 20 × 20 mm compact holder body Compatible with Horn indexable inserts Precision and stability for narrow cuts The holder's compact 20 × 20 mm cross section and 2 mm cutting width are engineered to provide concentrated rigidity in the cutting zone, reducing vibration during hard-to-reach parting operations. Compatibility with Horn inserts and the ISO 2020 insert form ensures predictable seating and repeatable geometry when new inserts are installed. For workshops migrating from brazed or custom blades, this configuration improves process repeatability and reduces scrap by delivering consistent cut widths and reliable chip flow. Engineered for reliable machining performance With a maximum parting depth of 18 mm and a 125 mm overall length, the design balances reach with torsional stiffness to maintain dimensional accuracy in short to medium overhangs. The right‑hand orientation suits standard lathe feed directions and integrates with conventional tool posts; the adapter designation 2C‑R S224 identifies the compatible shank connection for straightforward mounting. The holder’s modest 0.406 kg mass contributes to dynamic stability without adding unnecessary inertia, helping to avoid chatter and to extend insert life under normal cutting parameters. Workshop integration and operational advantages Standardised interface and ISO designation simplify inventory and tooling management: the holder accepts commonly available indexable inserts and mates with industry‑standard clamping systems, which reduces downtime for changeovers. The compact form factor is particularly useful in multi‑station setups or smaller lathes where space is limited, while the clear definition of cutting direction and insert type aids process planning. Technical staff benefit from the combination of concise specification and familiar interfaces, allowing faster set‑up and predictable performance in serial production or jobbing environments. For application advice and procurement of the Teknik Makina D701TM parting-off clamping holder, contact Metav Werkzeuge in Emmerich at info@metav-werkzeuge.com or call +49 2822 7131930 for tailored support and delivery information Technical Data Article number: D701TM Manufacturer: Teknik Makina Designation: Parting-off clamping holder eClass: 21181005 Dimensions & Weight Holder height: 20 mm Holder width: 20 mm Cutting-head width: 20 mm Cut width: 2 mm Maximum parting depth: 18 mm Overall length: 125 mm Weight: 0.406 kg Compatibility & Features Cutting direction: right-hand Suitable for Horn indexable inserts ISO insert designation: 2020 Shank/adapter designation: 2C-R S224 FAQ What maximum depth can be machined with this holder? The maximum parting depth is specified as 18 mm for the Parting-off clamping holder D701TM, allowing for secure short-to-medium depth operations. Which insert form is compatible with this tool holder? The D701TM accepts ISO 2020 insert forms and is specified as compatible with Horn indexable inserts for straightforward replacement and repeatability. Is the holder suitable for right‑hand and left‑hand turning centres? This holder is manufactured for right‑hand parting operations; on left‑hand machines an alternative orientation would be required. What are the key dimensions relevant for tool post mounting? Important mounting dimensions include a 20 × 20 mm holder body and a 125 mm overall length; the shank/adapter designation is 2C‑R S224 for compatibility checks. How does the compact design affect machining stability? The compact 20 × 20 mm profile and modest mass (0.406 kg) concentrate rigidity at the insert, improving resistance to vibration and supporting consistent parting results. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Combining precise left‑hand cutting with a narrow 2 mm cutting width and a secure clamping geometry delivers dependable parting and grooving performance in production and repair shops; order the holder directly via Metav Werkzeuge or request specialist advice from our consultants for suitable setup and inserts. Teknik Makina Stechklemmhalter — left‑hand parting tool holder with 2 mm cutting width A robust steel tool holder designed for left‑hand parting and grooving operations, compatible with Sandvik indexable inserts in ISO 2020 format and intended for secure installation in 2C‑123 SDV‑L tool shanks Left‑hand cutting for plunge and grooving 2 mm cutting width for narrow parting cuts 125 mm overall length for secure reach Compatible with Sandvik ISO 2020 inserts Consistent parting quality through engineered geometry The holder is engineered to maintain a stable cutting line and predictable chip flow during longitudinal cutting and plunge operations. Its left‑hand cutting orientation and 2 mm cutting width provide a narrow kerf suitable for close tolerances and minimal material waste. The combination of narrow cutting width and a defined 18 mm maximum plunge depth allows controlled engagement when entering the workpiece, reducing chatter and improving surface finish. This stability translates into fewer rejected parts and less secondary machining, supporting efficient production cycles. Stable clamping and repeatable set‑ups for toolrooms A compact yet rigid construction keeps the cutting edge precisely positioned: the tool offers a holder height of 20 mm, holder width of 20 mm and a head width of 20 mm, giving a robust contact area for the clamping screws. The specified shank form 2C‑123 SDV‑L provides a straightforward fit in compatible toolposts and reduces set‑up time. With a mass of 0.4 kg, the assembly balances rigidity with manageable handling during tool changes, ensuring repeatable set‑ups and consistent cutting results across serial runs. Compatibility and workflow benefits for mixed fleets Designed to accept Sandvik‑compatible indexable inserts in the ISO 2020 size, the holder integrates easily into existing insert inventories and reduces the need for multiple specialised parting tools. The 125 mm overall length gives sufficient reach for most lathe turrets while keeping the overhang moderate to limit deflection. For workshops seeking cost‑effective standardisation, this holder reduces tool diversity without compromising capability, helping to streamline ordering and inventory management. For reliable left‑hand parting operations, contact Metav Werkzeuge to order the Teknik Makina Stechklemmhalter (SKU D873TM) or to request specialist advice from Emmerich on the best insert choices and set‑up options. Technical data SKU: D873TM Manufacturer: Teknik Makina Weight: 0.4 kg Overall length: 125 mm Facts Holder height: 20 mm Holder width: 20 mm Head width: 20 mm Cutting width: 2 mm Max plunge depth: 18 mm Shank designation: 2C-123 SDV-L ISO designation: 2020 Cutting direction: left Special features Compatible with Sandvik indexable inserts Designed for parting and grooving operations Robust clamping geometry for repeatability FAQ What types of inserts fit this holder? The holder accepts ISO 2020 indexable inserts; it is specified as Sandvik‑compatible, making standard Sandvik parting inserts suitable for the application. Is the holder suitable for plunge cutting on shafts? Yes. The holder’s 18 mm maximum plunge depth and narrow 2 mm cutting width are intended for controlled plunge and parting tasks on cylindrical workpieces. Which shank or toolpost does the holder require? The tool is designed for use with a 2C‑123 SDV‑L shank designation, providing a secure fit in matching toolholders and reducing set‑up time. How does the holder contribute to vibration control? A compact contact area—20 mm in height and width combined with the robust head—reduces overhang and increases stiffness, helping to control vibration and improve surface finish during high‑demand cuts. Can this holder be used in mass production environments? Yes. The combination of repeatable clamping geometry, standard ISO 2020 insert compatibility and a moderate 125 mm overall length makes it suitable for serial production where consistent parting performance is required. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of a compact combination of secure clamping, exact 2 mm cutting capability and a 125 mm overall length for reliable parting and grooving operations. Order the holder directly via Metav Werkzeuge or consult the team for tailored application advice. Stechklemmhalter – Parting tool holder with 2 mm cutting width | Teknik Makina Stechklemmhalter designed for precise parting and grooving on lathes, compatible with Walter GX24 indexable inserts and optimised for tight, repeatable cuts 2 mm cutting width for narrow grooves 20 x 20 mm shank for secure mounting Compatible with Walter GX24 indexable inserts 18 mm maximum plunge depth Accurate narrow cuts for consistent parting The 2 mm cutting width enables precise, narrow grooves and clean parting operations. With an insert-compatible design for GX24 indexable inserts, the holder maintains repeatable geometry across multiple tool changes, reducing set-up variation. Indexable inserts are replaceable cutting edges that preserve tool alignment and minimise downtime; using a dedicated clamping unit ensures consistent seat contact and reliable chip control during short, high-precision cuts. Secure mounting and stable clamping reduce vibration A square shank with an ISO designation 2020 and nominal dimensions of 20 x 20 mm provides a firm interface with standard tool posts and quick-change systems. The clamping arrangement holds the insert seat and cutting head dimensions of 20 mm to maintain rigidity during plunge and grooving tasks. Reduced deflection supports predictable tool life and improved surface quality, which is particularly beneficial in serial turning where every micrometre of deviation affects downstream processes. Compact design to boost workshop throughput With an overall length of 125 mm and a mass of 0.403 kg, the unit balances accessibility and stability for typical lathe setups. The 18 mm maximum plunge depth permits controlled engagement for deeper grooves without excessive overhang. The slim geometry and compatibility with the 2C GX24 bar designation make the clamping holder a practical choice for confined workspaces and processes that require frequent insert changes, helping to shorten cycle times and streamline production flows. For expert application support or to secure stock of this Teknik Makina parting tool holder, contact Metav Werkzeuge for product availability and practical recommendations tailored to the turning task at hand – Metav Werkzeuge is ready to advise and supply from Emmerich. Technical Data Article number: D864TM Manufacturer: Teknik Makina Designation: Stechklemmhalter ECLASS: 21181005 Facts Shank height: 20 mm Shank width: 20 mm Cutting head width: 20 mm Cutting width: 2 mm Maximum plunge depth: 18 mm Overall length: 125 mm Weight: 0.403 kg ISO designation: 2020 Special features Compatible with inserts: GX24 Compatible insert manufacturer: Walter Compatible boring bar designation: 2C GX24 Suitable for parting and grooving operations FAQ What inserts fit this clamping holder? The clamping holder accepts GX24 indexable inserts and is specified for inserts from Walter, ensuring a standardised seating and cutting geometry. What is the maximum plunge depth for this holder? The tool offers a maximum plunge depth of 18 mm, allowing controlled engagement for deeper grooves within that limit. Which shank size should the tool post accept? The square shank conforms to 20 x 20 mm (ISO 2020) dimensions for secure mounting on compatible tool posts and quick-change systems. Is the holder suitable for confined lathe setups? Yes; the compact 125 mm overall length and modest weight support installation in restricted work envelopes while maintaining stability. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of a compact, left-hand parting tool holder that combines precise clamping, compatibility with Korloy 2C MGM inserts and a rigid 20 × 20 mm ISO shank for consistent repeatability on turning machines — order directly via Metav Werkzeuge or request guidance from our workshop consultants. Parting Tool Holder D610TM — Left-hand, 2 mm cutting width (Teknik Makina) The Parting Tool Holder D610TM is a left-hand parting and grooving holder designed for lathe toolposts, accepting Korloy 2C MGM inserts and matching an ISO 2020 20 × 20 mm shank for stable machining. Left-hand cutting orientation Accepts Korloy 2C MGM inserts ISO 2020 20 × 20 mm shank 2 mm cutting width, 16 mm max depth Stable clamping that reduces chatter and rework The D610TM delivers positive clamping and consistent seating with a compact 20 × 20 mm shank that matches ISO 2020 tooling systems. The holder’s geometry provides a secure grip on the insert carrier, which improves repeatability from cut to cut and reduces the need for rework. For workshops seeking reliable parting performance, the robust clamping reduces vibration and supports more predictable cycle times on production and repair jobs. Efficient material removal with controlled cutting depth Designed for narrow-section operations, the holder supports a 2 mm cutting width and a maximum parting depth of 16 mm, enabling controlled engagement for fine parting and grooving. The left-hand orientation suits left-oriented setups or specific part geometries, while the defined width helps maintain chip shape and stability. These characteristics translate into fewer tool changes and better surface integrity during turning operations, improving throughput on batch and single-piece work alike. Compact footprint for versatile workshop integration With an overall length of 125 mm and a nominal weight of 0.404 kg, the tool holder offers a compact package that fits confined toolpost spaces without sacrificing stiffness. The modest dimensions make it especially suitable for small lathes or multi-station turrets where tool spacing is critical. The holder’s balance between compactness and rigidity supports steady cutting conditions, helping to preserve insert life and reduce downtime. Broad compatibility for simplified tooling management Compatibility with Korloy 2C MGM inserts and the designation matching 2C-L MGM clamping bars means straightforward integration into existing tooling inventories. The ISO 2020 shank dimension ensures interchangeability with standard holders and post systems, simplifying stock and reducing procurement complexity. For production environments aiming to minimise tooling variants, this holder provides a clear technical fit to established insert families and mounting conventions. Choose the Teknik Makina Parting Tool Holder D610TM via Metav Werkzeuge for dependable parting performance — our Emmerich-based team provides product guidance and rapid supply to keep workshop schedules on track; contact Metav Werkzeuge at info@metav-werkzeuge.com or +49 2822 7131930 for technical advice and order support Technical Data SKU: D610TM Manufacturer: Teknik Makina Designation: Parting tool holder Shank size: 20 × 20 mm (ISO 2020) Cutting direction: left Compatible inserts: Korloy 2C MGM Cutting width: 2 mm Max parting depth: 16 mm Overall length: 125 mm Weight: 0.404 kg Key Figures Shank height: 20 mm Shank width: 20 mm Cutting width: 2 mm Max cutting depth: 16 mm Overall length: 125 mm Weight: 0.404 kg Special features ISO designation: 2020 Bohrstangen designation: 2C-L MGM Suitable for Korloy 2C MGM inserts FAQ What insert type is required for this holder? The holder is made for Korloy 2C MGM inserts; the D610TM accepts the 2C geometry and secures the insert with the matching clamping arrangement. Is the cutting direction left or right? This tool holder is a left-hand model; its geometry and seat are oriented for left-hand cuts on the lathe. What shank size does the holder use? The D610TM uses a 20 × 20 mm shank, conforming to the ISO 2020 dimension for easy integration into standard toolposts. How deep can the parting operation be with this holder? The maximum parting depth is 16 mm, with a cutting width of 2 mm suitable for narrow grooving and parting tasks. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of a compact, rigid holder with a 16×16 mm shank and a 2 mm cutting width to secure consistent right‑hand parting and grooving operations — order the tool directly via Metav Werkzeuge or contact our consultants for application advice. Parting/clamping holder D752TM – right‑hand grooving holder, 16×16 mm (Teknik Makina) The parting/clamping holder D752TM is designed for right‑hand grooving and parting tasks on modern lathes, offering a compact 125 mm overall length and compatibility with 2C DGN indexable inserts 16×16 mm shank for robust clamping 2 mm cutting width for precise parting 16 mm maximum plunge depth Compatible with ISCAR 2C DGN inserts Consistent rigidity for uninterrupted production A solid 16×16 mm shank combined with a compact 125 mm overall length provides mechanical stability that reduces vibration during cutting. The holder’s low mass (0.26 kg) and compact footprint make it suitable for both busy production lines and smaller job‑shop lathes. This structural stability translates into steadier cuts, less tool chatter and improved surface finish, which helps maintain cycle times and reduces the need for rework. Predictable cutting performance through standardised insert use Designed for 2C DGN indexable inserts and compatible with ISCAR tooling, the holder accepts a narrow 2 mm cutting width and allows a 16 mm maximum plunge depth. Using standard insert formats simplifies tool management and regrinding schedules while ensuring repeatable chip evacuation and dimensional control. The right‑hand orientation suits the most common turning set‑ups, offering a clear, engineering‑driven advantage when processing narrow grooves or parting off finished components. Practical integration into workshop workflows The holder’s ISO 1616 shank designation and the secondary designation 2C‑R DGN support straightforward mounting and replacement in existing tool turrets. Its compact dimensions free up turret stations and allow closer tool packing, which benefits multi‑operation turning cells. For maintenance and procurement teams, the standardised interfaces reduce inventory complexity and speed up changeovers — factors that contribute directly to higher machine availability and lower per‑part production cost. For tailored advice and reliable supply from Metav Werkzeuge in Emmerich, contact our specialists to discuss the D752TM parting/clamping holder and find the optimal insert and machining parameters for the application Technical data Article number: D752TM Manufacturer: Teknik Makina Designation: Parting/clamping holder D752TM SKU: D752TM Facts Shank width/height: 16 mm × 16 mm Cutting width: 2 mm Maximum plunge depth: 16 mm Overall length: 125 mm Weight: 0.26 kg Cutting direction: right Special features Compatible with 2C DGN indexable inserts Suitable for ISCAR inserts (manufacturer reference) ISO designation: 1616 Secondary shank/bezel designation: 2C‑R DGN Application: parting and grooving in turning operations FAQ What insert types are recommended for this holder? The D752TM accepts 2C DGN indexable inserts; ISCAR‑type 2C DGN inserts are a standard match for predictable chip control. Is the holder suitable for deep grooving operations? The holder permits a maximum plunge depth of 16 mm, which is adequate for many parting and medium‑depth grooving tasks on lathes. Which machines is this holder intended for? This compact holder is designed for turret‑mounted turning centres and conventional lathes where a 16×16 mm shank can be accommodated and where right‑hand cutting is required. How does the holder support repeatable results? Standardised shank dimensions (ISO 1616) and compatibility with common insert formats ensure repeatable clamping, quick replacement and consistent machining tolerances. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of a compact holder that combines precise left-hand parting with minimal tool overhang and reliable clamp-style fixation. The D730TM offers a 3 mm cutting width and a maximum parting depth of 16 mm, enabling efficient short-run parting and grooving in confined turning operations. Order the parting clamp holder directly via Metav Werkzeuge or ask our consultants if needed. Parting clamp holder D730TM — Left-hand parting tool holder by Teknik Makina The Parting clamp holder D730TM is a left-hand clamp-style holder for parting and grooving, designed for use with ISCAR indexable inserts in demanding lathe operations. Left-hand cutting direction Compatible with ISCAR 3C DGN inserts 3 mm cutting width Overall length 125 mm Accurate, repeatable parting for tighter tolerances The clamp-style design delivers stable clamping and reduced vibration, which supports consistent parting performance and repeatable results. By securing the insert with a compact clamping block, the holder minimises play during cut engagement; this translates into fewer rejects and less rework when producing turned components. The ISO designation 1212 ensures a standardised interface for insert seating and orientation, simplifying insert replacement and inspection. Short set-up times and efficient machining cycles With a modest overall length of 125 mm and a low mass of 0.16 kg, the holder reduces tool overhang and inertia, enabling faster acceleration and safer clearances during program cycles. The simple geometry and clamp mechanism cut setup time and allow quick insert changes, supporting lean production flows and higher machine uptime. These features make the D730TM suitable where rapid changeovers and throughput are priorities. Compact form for constrained turning operations Where carriage travel or cross-slide clearance is limited, the compact dimensions (holder height 12 mm; holder width 12 mm) permit close-to-workpiece machining without sacrificing cutting stability. The narrow 3 mm cutting width is ideal for fine parting, slotting and narrow-groove applications, allowing precise control of chip evacuation and reduced cycle loads in small-diameter workpieces. Proven compatibility and practical application advice Engineered for use with ISCAR 3C DGN indexable inserts, the holder accepts standard insert sizes and can be integrated easily into existing tool setups. The left-hand cutting orientation is suitable for operations where the tool must cut when travelling from tailstock to headstock; match the holder to lathe setup and insert geometry to achieve the best surface finish and tool life. For specific applications and recommended cutting parameters, Metav Werkzeuge’s technical advisors can provide guidance. Contact Metav Werkzeuge for tailored application advice on the Teknik Cutting Tools D730TM and secure a reliable left-hand parting solution for precision turning tasks, served directly from Emmerich with swift logistical support. Technical data Article number: D730TM Manufacturer: Teknik Makina Brand: Teknik Cutting Tools SKU: D730TM Facts Overall length: 125 mm Holder height: 12 mm Holder width: 12 mm Cutting head width: 12 mm Cutting width: 3 mm Maximum parting depth: 16 mm Weight: 0.16 kg Cutting direction: left Special features Compatible with ISCAR 3C DGN inserts ISO designation: 1212 Shank/holder designation: -3C-L DGN Compact clamp-style mounting FAQ What inserts fit this holder? The D730TM is designed for ISCAR 3C DGN indexable inserts; select the matching insert geometry and grade for the machining material. Is the cutting direction left- or right-hand? This holder is specified for left-hand cutting operations and is intended for cuts made from tailstock towards headstock. What maximum parting depth can be achieved? Maximum achievable parting (stepping) depth is 16 mm, as defined by the holder geometry. What are the key dimensions to consider for set-up? Important dimensions include overall length 125 mm, holder height 12 mm, holder width 12 mm and cutting width 3 mm. Can the holder be used for narrow grooving as well as parting? Yes; the narrow 3 mm cutting width and rigid clamp fixation make it suitable for narrow-groove operations as well as standard parting tasks. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com