Gibt es einen Hahn und Kolb Online Shop?

Benefit from a compact, workshop‑ready parting solution combining a 20 × 20 mm tool shank interface with a 125 mm overall length for extended reach and a maximum parting depth of 16 mm; order via Metav Werkzeuge or contact our consultants for application advice. Parting tool clamp holder L125mm – left‑hand, 20 × 20 mm shank (Teknik Makina) The Parting tool clamp holder L125mm is a left‑hand parting holder designed for turning operations where secure clamping and precise depth control are required, compatible with standard 20 × 20 mm tool posts. Left‑hand cutting orientation 20 × 20 mm tool shank compatible 125 mm overall length for reach Max parting depth 16 mm, 2 mm blade width Secure clamping that keeps cuts true A rigid clamping interface is essential for accurate parting; this holder is built around the 20 × 20 mm standard and the ISO 2020 designation, which ensures compatibility with common tool posts and fixtures. The integrated M6×20 clamping screw secures the blade reliably, reducing vibration and enabling repeatable cuts. That translates into fewer reworks and steadier process control when performing routine parting and grooving tasks in production work. Predictable cutting performance for process planning When process planners require quantifiable limits, the holder delivers a maximum parting depth of 16 mm with a nominal 2 mm blade width, enabling clear decisions about tool selection and cycle planning. The left‑hand cutting orientation is specified for use where the tool approaches the workpiece from the appropriate side; this simple characteristic removes ambiguity during fixture setup and helps maintain consistent surface finish and dimensional control across batches. Compact design for workshop flexibility With an overall length of 125 mm and a mass of approximately 0.401 kg, the holder is compact yet practical for tight toolpost arrangements and multi‑tool turrets. The included 5 mm Allen key specification and the standard clamping screw type mean familiar workshop tooling is sufficient for assembly and adjustments. Such practical dimensions and familiar fastenings reduce setup time and simplify maintenance routines on the shop floor. Practical integration and application guidance The holder is intended for conventional turning operations requiring a clamp‑style parting solution and fits into established tool inventories thanks to its standard dimensions and ISO alignment. For tasks bordering the holder’s limits—deeper parting, unusual alloys or interrupted cuts—consultation is recommended to match blade geometry and cutting data. Metav’s product expertise and technical resources support selection and ensure the holder is deployed where it contributes to stable productivity. Contact Metav Werkzeuge for tailored application advice and specify SKU D882TM when enquiring to ensure fast, precise support from our specialists. Technical Data Article number: D882TM ECLASS: 21181005 Label: Parting tool clamp holder L125mm SKU: D882TM Facts Overall length: 125 mm Weight: 0.401 kg Holder width: 20 mm Holder height: 20 mm Cutting head width: 20 mm Max parting depth: 16 mm Cutting width: 2 mm Special features Left‑hand cutting direction ISO 2020 size (20 × 20 mm) M6×20 clamping screw 5 mm Allen key specification SKU for reference: D882TM FAQ Which toolpost size is compatible with this holder? The holder accepts the standard 20 × 20 mm tool shank (ISO 2020), making it compatible with common toolposts and fixtures used for parting operations. What maximum parting depth can be achieved? This parting clamp holder supports a maximum parting depth of 16 mm with a nominal blade width of 2 mm. Is the holder for left‑hand or right‑hand cutting? The unit is specified for left‑hand cutting orientation; this is noted on the product data for correct mounting and use. What are the overall length and mass of the holder? The overall length is 125 mm and the weight is approximately 0.401 kg, suitable for compact setups and standard turret tooling. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of a compact combination of compatibility and coolant-fed performance: the KA234TM boring bar pairs a Ø12 mm cutting diameter with internal coolant and a rigid 10 mm shank to reduce vibration and preserve insert life. Order directly via Metav Werkzeuge or request tailored advice from our consultants for smooth integration into existing tool setups. KA234TM Boring bar — SCLC type for CC-- indexable inserts, Ø12 mm, internal coolant KA234TM is a compact SCLC-style boring bar intended for use with CC-- 0602 indexable inserts; designed for left-hand cutting in machining centres and lathes Suitable for CC-- 0602 indexable inserts Ø12 mm cutting diameter Internal coolant supply Left-hand cutting direction High-precision compatibility for indexable tooling The A10J SCLCL designation identifies a standard SCLC-style holder that accepts CC-- 0602 indexable inserts, ensuring straightforward replacement and repeatable seat location. With a 10 mm shank and a specified 20 mm cutting height, the tool is engineered to deliver stable seating and consistent radial positioning; this reduces setup variability and supports predictable machining results. Compatibility with common insert geometries simplifies inventory and shortens changeover times. Improved rigidity and coolant control for consistent results The combination of a 110 mm overall length and compact mass (0.074 kg) gives the bar a favourable stiffness-to-length ratio for many medium-duty turning tasks; the reduced overhang helps limit chatter and maintain surface quality. Integrated internal coolant directs cutting fluid to the cutting zone, improving chip evacuation and heat control—factors that extend insert life and contribute to repeatable cycle times. Left-hand cutting orientation is specified where reverse-feed operations or particular clamping layouts are required. Rapid integration into clamping systems and workshop workflows The holder is supplied in an SCLC arrangement with a clamping designation of 06, enabling straightforward mounting in compatible tool posts and turret stations. Use of indexable inserts minimises downtime for regrinding while allowing quick application-specific changeovers. For toolrooms and production shops seeking predictable tool behaviour and easy stock management, this compact boring bar supports efficient machining without complex retrofitting. For precision applications requiring coolant-fed indexable solutions, contact Metav Werkzeuge for tailored advice on incorporating the KA234TM into existing toolsets — Metav Werkzeuge is ready to confirm technical fitment and arrange delivery from Emmerich: info@metav-werkzeuge.com | +49 2822 7131930. Technical data Article number: KA234TM Product: Boring bar Manufacturer: Teknik Cutting Tools / Responsible: Metav Werkzeuge GmbH Numbers / Core technical data Cutting diameter: 12 mm Shank diameter: 10 mm Cutting height: 20 mm Overall length: 110 mm Weight: 0.074 kg Cutting angle: 95° Special features / Versions ISO designation: A10J SCLCL For indexable inserts: CC-- 0602 Internal coolant: yes Cutting direction: left Clamping designation: 06 FAQ What insert type fits this boring bar? The KA234TM boring bar is designed for CC-- 0602 indexable inserts and follows the SCLC holder standard for correct seating and repeatability. Is coolant supply available through the tool? Yes — the bar features internal coolant to direct fluid to the cutting edge for improved chip control and thermal management. What are the key dimensions to check for machine compatibility? Important dimensions include the Ø12 mm cutting diameter, 10 mm shank diameter and 110 mm overall length; these define overhang and clamp fit. Can the bar be used for reverse-direction operations? The tool is specified for left-hand cutting, which suits applications with reverse-feed requirements or specific fixture orientations. Which clamping size is required for mounting? The boring bar carries a clamping designation 06, matching common SCLC-type toolholders and enabling direct integration into compatible tool posts. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com

Precision turning benefits from internal coolant and secure clamping for DC-- 0702 indexable inserts, while the left-hand orientation suits specialised turning tasks; order the KA270TM via Metav Werkzeuge or consult our product advisers for tailored application support. KA270TM Boring Bar (A10J SDQCL) by Teknik Makina — Left-hand, internal coolant A KA270TM boring bar designed for turning operations with DC-- 0702 indexable inserts, providing coolant-fed chip control and a compact footprint for CNC lathes A10J SDQCL ISO designation Internal coolant for improved chip evacuation Compatible with DC-- 0702 indexable inserts Left-hand cutting, 12 mm cutting diameter Greater process reliability through coolant-fed chip control The internal coolant channel delivers cutting fluid directly to the insert edge, markedly improving chip evacuation and reducing thermal load at the cutting zone. This direct feed helps maintain tool life under continuous operation and lowers the risk of built-up edge formation. For workshop environments where cycle time and repeatability matter, the coolant feature supports stable cutting forces and fewer unscheduled tool changes, contributing to predictable machining output. Fast setup and repeatable clamping for indexable inserts Designed around the DC-- 0702 insert family, the toolholder carries the A10J SDQCL ISO designation and accepts the defined clamping system 07, enabling rapid insert changes and consistent seating. The cutting angle 107.5° and a 20 mm effective cutting height are matched to the insert geometry, so setting and re-establishing cutting parameters is straightforward. These characteristics reduce setup time and improve process repeatability, which is essential for batch production or finishing passes on turned components. Compact design for precision and minimal vibration in confined workspaces Small-diameter construction with a 12 mm cutting diameter, 10 mm shaft diameter and 110 mm overall length keeps overhang to a minimum, lowering bending and chatter during fine turning; the tool weighs 0.074 kg, aiding rapid spindle acceleration and dynamic stability. The left-hand cutting orientation broadens suitability for specific turning sequences and fixtures on CNC lathes. The KA270TM presents a compact, performance-oriented solution where precision, rigidity and reliable insert support are required. For specification advice or to arrange supply of the Teknik Cutting Tools KA270TM boring bar, contact Metav Werkzeuge for availability and expert recommendations Technical data SKU: KA270TM Manufacturer: Teknik Makina Model designation: A10J SDQCL English description: SDQC for DC-- Indexable Inserts Core dimensions Cutting diameter: 12 mm Shaft diameter: 10 mm Cutting height: 20 mm Overall length: 110 mm Weight: 0.074 kg Cutting angle: 107.5° Features & compatibility Internal coolant: yes Compatible inserts: DC-- 0702 Clamping holder: 07 Cutting direction: left Intended for indexable-insert turning operations FAQ What inserts fit this boring bar? The KA270TM boring bar is compatible with DC-- 0702 indexable inserts and is designed to accept the matching clamping system for secure retention. Does the tool support internal coolant? Yes, the KA270TM features internal coolant to supply cutting fluid directly to the insert edge, improving chip evacuation and thermal control. Is this tool suitable for confined or small-diameter turning? With a 12 mm cutting diameter and 110 mm overall length, the KA270TM is engineered to minimise overhang and reduce vibration in compact turning operations. What is the cutting orientation of the bar? The bar is configured for left-hand cutting, making it appropriate for machining sequences that require that orientation on a lathe. Which ISO designation applies to the toolholder? The toolholder is specified as A10J SDQCL, reflecting its design for SDQC-style indexable-insert applications. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of the 107.5° cutting angle together with internal coolant to improve chip control and machining consistency; the compact shaft diameter 10 mm and overall length 110 mm support installations with limited overhang. Order directly via Metav Werkzeuge or consult our specialists for technical guidance. Teknik Makina A10J SDQCR boring bar — 107.5° for DC-- 0702 indexable inserts, internal coolant The A10J SDQCR boring bar is a right-hand, compact tool designed for internal turning with DC-- 0702 indexable inserts, offering directed cooling and a geometry matched to standard DC-- insert grades 107.5° cutting angle for DC-- 0702 inserts Internal coolant for direct chip cooling Compatible with DC-- 0702 indexable inserts Compact overall length of 110 mm Precise compatibility with DC-- 0702 inserts The tool is engineered around the DC-- 0702 insert family, so the 107.5° cutting angle aligns with common insert geometries to ensure repeatable seating and consistent cutting engagement. By using the standardised insert form, changeovers are straightforward and downtimes are reduced; the insert system also enables fast replacement without regrinding, supporting cost‑efficient production runs. The right‑hand cutting orientation further clarifies setup and toolpath planning in CNC routines. Controlled cooling for longer cutting cycles Equipped with internal coolant, the boring bar routes coolant directly to the cutting zone, aiding chip evacuation and temperature control at the edge. This targeted coolant feed reduces thermal load on the insert and helps maintain a stable cutting edge geometry over time. In practical terms, the internal feed supports steady machining performance during longer cycles and under interrupted cuts where coolant access is otherwise limited. Compact dimensions for tight machining setups With a shaft diameter 10 mm, nominal diameter 12 mm and an overall length 110 mm, the bar is suited to operations where space is restricted or where short overhang is essential for rigidity. The compact profile helps limit vibration and deflection compared with longer, slender alternatives, while the modest mass (0.074 kg) contributes to lower spindle load. The cutting height 20 mm provides the required clearance for DC-- 0702 inserts and ensures correct insert seating in standard clamping systems. Engineered for efficient workshop production The combination of indexable inserts and straightforward mechanical design supports high uptime and simple servicing in industrial workshops and toolrooms. The modular insert system minimises preparation time, and the bar’s standard designation (A10J SDQCR) fits widely used holders and turret systems. For procurement decisions, this configuration balances compatibility and process continuity, making it a pragmatic choice for manufacturers aiming to streamline tool inventories while maintaining machining quality. For precise tooling enquiries or to order the Teknik Makina A10J SDQCR boring bar, contact Metav Werkzeuge for expert advice and prompt delivery via info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: KA140TM Manufacturer: Teknik Makina ISO designation: A10J SDQCR Designation (EN): SDQC for DC-- Indexable Inserts Numerical data Shaft diameter: 10 mm Diameter: 12 mm Overall length: 110 mm Weight: 0.074 kg Cutting height: 20 mm Cutting angle: 107.5° Special features Internal coolant: yes Cutting direction: right-hand For inserts: DC-- 0702 English designation: SDQC for DC-- Indexable Inserts FAQ Which indexable inserts are compatible with this boring bar? The Teknik Makina A10J SDQCR boring bar is compatible with DC-- 0702 indexable inserts and was designed around that insert geometry for secure seating and reliable cutting. Does the tool provide internal coolant? Yes, the boring bar includes internal coolant, enabling directed cooling to the cutting edge for improved chip control and temperature management. What is the cutting direction of the bar? The bar is specified for right-hand cutting, which should be set accordingly in the tool table and CNC programmes. What are the key dimensions to check for machine setup? Key dimensions include a shaft diameter of 10 mm, nominal diameter 12 mm, overall length 110 mm and cutting height 20 mm; these determine holder compatibility and overhang. Is this tool suitable for compact turrets and limited overhangs? The compact overall length and modest mass make the bar well suited to setups where short overhang and tight clearance are required, while still accommodating DC-- 0702 inserts. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Benefit from precise, repeatable boring operations thanks to the combination of a rigid 10 mm shaft, a 12 mm cutting diameter and integrated internal coolant — designed to reduce cycle times and improve surface finish. Order the KA134TM directly via Metav Werkzeuge or consult the Metav team for application advice. Boring bar KA134TM (A32T SDUCR) — 12 mm diameter, internal coolant, right‑hand cut — Teknik Cutting Tools The Boring bar KA134TM is a right‑hand, indexable‑insert boring bar designed for use with DC-- 0702 inserts and optimised for compact, precision machining in CNC setups. Internal coolant for improved chip evacuation Compatible with DC-- 0702 indexable inserts 12 mm diameter, 110 mm overall length Right‑hand cutting, 93° cutting angle Faster, more consistent metal removal through optimised geometry The bar’s 93° cutting angle and SDUC geometry deliver a stable cutting engagement that supports consistent material removal and predictable tool behaviour. By combining a modest overhang with a compact design, the tool reduces vibration and promotes a uniform surface result; this directly contributes to shorter cycle times and fewer rework operations. The internal coolant channel assists chip evacuation at the cutting zone, which helps maintain edge life and reduce heat‑related wear during continuous production runs. Simple integration with indexable‑insert systems for efficient tool changes Designed around the SDUC style, the tool accepts DC-- 0702 indexable inserts and uses the ISO designation A32T SDUCR, allowing straightforward matching with established holder and insert systems. The clamping concept enables rapid insert replacement, supporting minimal downtime in batch production. For workshops aiming to standardise tooling, the compatibility with common insert formats reduces inventory complexity while keeping maintenance fast and safe. Rigidity and accuracy in space‑constrained setups A 10 mm shaft diameter paired with an 110 mm overall length offers a compact balance between reach and stiffness. This configuration is particularly beneficial where limited tool overhang is required to preserve concentricity and surface quality. The low mass (0.08 kg) aids rapid acceleration on servo axes while the defined cutting height of 20 mm ensures the insert sits at the intended engagement depth for repeatable results. Practical guidance for use and expected outcomes Right‑hand cutting direction and the SDUC holder form mean the bar is suited to operations where controlled chip flow and directional cutting forces are important. The integrated internal coolant is most effective when the machine’s coolant supply is connected and pressure is set according to the machining centre’s recommendations. The tool’s ISO code (A32T SDUCR) and clear insert compatibility (DC-- 0702) simplify procurement and tool management in production environments that prioritise interchangeability and quick servicing. Contact Metav Werkzeuge for tailored technical advice and to secure the Teknik Cutting Tools KA134TM boring bar with integrated internal coolant and ISO A32T SDUCR designation — eMail info@metav-werkzeuge.com or call +49 2822 7131930 for delivery from Emmerich Technical Data SKU: KA134TM Manufacturer: Teknik Makina ISO designation: A32T SDUCR Type: SDUC for DC-- indexable inserts Numbers / Core Technical Data Diameter: 12 mm Shaft diameter: 10 mm Overall length: 110 mm Cutting height: 20 mm Weight: 0.08 kg Cutting angle: 93° Direction: Right Compatible insert: DC-- 0702 Internal coolant: Yes Design / Special features SDUC holder style Internal coolant channel Right‑hand cutting orientation Compatible with DC-- 0702 indexable inserts Compact, low‑mass construction FAQ Which inserts are compatible with this boring bar? The KA134TM is designed for DC-- 0702 indexable inserts in the SDUC system; select inserts matching the SDUC clamping and geometry for best performance. Does the tool provide internal coolant? Yes — the KA134TM features internal coolant to support chip evacuation and extend insert life when connected to the machine’s coolant supply. What is the ISO designation and why is it relevant? The bar carries the A32T SDUCR ISO code, which identifies its holder geometry and ensures compatibility with standard SDUC‑type tooling systems. Is the cutting direction suitable for common turning and milling applications? The tool is specified for right‑hand cutting, which is standard for many machining operations where right‑hand inserts and holders are used. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of the combination of an indexable design, a 12 mm cutting diameter and a sturdy 20 mm shank for consistent reverse-side chamfers and minimal downtime; order the tool directly via Metav Werkzeuge or contact their consultants for application advice. Back Countersink C102TM – Indexable reverse-side countersink, for CCMT inserts, 12 mm cutting diameter The Back Countersink C102TM is an indexable countersinking tool engineered for reliable reverse-side chamfering in turning and milling operations, designed to accept standard CCMT carbide inserts for efficient edge formation Indexable design for CCMT 060204 inserts 12 mm cutting diameter for precision chamfers 20 mm shank diameter for standard toolholders 117 mm overall length, weighs 0.21 kg Consistent, accurate chamfers with indexable cutting technology The indexable construction ensures repeatable results: an indexable seat accepts the widely available CCMT 060204 insert, giving a predictable chamfer profile with each change. A single effective cutting edge produces a controlled chip flow that simplifies chip evacuation and reduces the risk of edge damage. The 12 mm cutting diameter is targeted at common chamfering tasks, providing a balance between precision and material removal for reverse-side finishing on turned or milled components. Fast insert changes and low-maintenance operation Maintenance is straightforward: the insert is secured with a Torx screw to the pocket, allowing rapid replacement and consistent seating. The Torx fastening uses M2.5x5.5 hardware and a T8 key for positive engagement and minimal slippage during service. Because insert swaps are quick, the tool reduces machine downtime and supports higher net productivity while keeping tooling inventory manageable with standard CCMT inserts. Stable clamping and compatibility with standard holders A 20 mm shank delivers a rigid connection to common toolholders while the 117 mm overall length offers reach without excessive cantilever. The heavy-duty shank-diameter pairing stabilises the cutting edge during reverse-side operations, which helps to maintain surface finish and dimensional conformity. Compatibility with standard toolholders removes the need for specialised adaptors and streamlines set-up across multiple machines. Proven supply reliability from a specialist partner Select tooling from a trusted supplier to avoid production interruptions: Metav combines a broad product range with central distribution from Emmerich, supporting workshops with expert advice and dependable logistics. The practical result is a straightforward sourcing route for precision tooling, backed by an experienced partner that has supplied thousands of customers across industry and trade. For straightforward ordering or to discuss suitability for specific applications, contact Metav Werkzeuge — Metav Werkzeuge GmbH, Parkring 45, 46446 Emmerich; info@metav-werkzeuge.com; +49 2822 7131930 — for personalised advice and supply of the indexable Back Countersink C102TM Technical data Article number: C102TM Manufacturer: Teknik Makina Facts Cutting diameter max: 20 mm Nominal diameter: 12 mm Shank diameter: 20 mm Overall length: 117 mm Weight: 0.21 kg Cutting edges: 1 Torx screw: M2.5x5.5 Torx key: T8 Special features For indexable inserts: CCMT 060204 Indexable reverse-side countersinking tool Single cutting edge design Standard shank format for common toolholders FAQ Which insert type does this countersink use? The Back Countersink C102TM uses CCMT 060204 indexable inserts for predictable chamfers and easy replacement. How is the insert secured in the tool? An M2.5x5.5 Torx screw secures the insert; the appropriate driver size is T8, ensuring firm seating and straightforward maintenance on the C102TM. What shank size is required to hold the tool? The tool features a 20 mm shank, compatible with standard holders that accept 20 mm tooling shanks. What is the overall reach of the tool? Overall length for the C102TM is 117 mm, offering sufficient reach for many reverse-side countersinking applications. How many cutting edges does the tool have? The tool incorporates 1 cutting edge per insert pocket, producing controlled chip formation for chamfering tasks. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com

Take advantage of the combination of internal coolant, solid carbide construction and precise insert compatibility for reliable internal boring; order or request specification support from Metav Werkzeuge to ensure correct holder selection. Boring bar SCLC with Coolant — solid carbide, internal coolant, 12 mm, Teknik Makina Boring bar SCLC with Coolant for precision internal machining, designed for left-hand operations and compatible with standard CC‑0602 indexable inserts Solid carbide construction Internal coolant channel For CC‑0602 indexable inserts 12 mm diameter, 125 mm overall length Reliable accuracy through focused design and coolant delivery The bar is manufactured from solid carbide, which provides high stiffness and wear resistance for tight-tolerance internal boring. Combined with the internal coolant channel, the coolant is delivered directly to the cutting zone to reduce heat and improve surface finish, which in turn extends insert life and reduces scrap rates. The tool’s compact mass and balanced geometry support consistent tool life and repeatable bore quality in serial production. Faster setup and controlled chip management for efficient machining Compatibility with CC‑0602 indexable inserts and the ISO E10K SCLCL 06 designation enable straightforward integration into existing turning and boring workflows, keeping setup times short. The insert is secured with a T8 torx screw specification M2.5x5.5, allowing quick index changes and minimal downtime. With a 6 mm cutting height and left-hand cutting orientation, the bar is optimised for applications that demand controlled chip flow and dependable cycle times. Easy integration with standard holders and practical handling The bar’s external dimensions — 12 mm cutting diameter, 125 mm overall length and a 10 mm shank — allow mounting in common boring holders designed for the E10 shank series, facilitating rapid adoption on existing machines. At approximately 0.1 kg, the component is simple to handle when changing tools or performing checks. For confirmation of holder compatibility or assistance selecting the correct clamping solution, technical enquiries are welcome. Contact Metav Werkzeuge for tailored tooling advice and precise holder recommendations for the KE18TM boring bar with internal coolant, ensuring optimal performance on your machines Technical Data Article number: KE18TM Manufacturer: Teknik Makina SKU: KE18TM ISO designation: E10K SCLCL 06 Core specifications Diameter: 12 mm Overall length: 125 mm Shank / clamping diameter: 10 mm Cutting height: 6 mm Weight: 0.1 kg Cutting direction: left Special features Solid carbide material Internal coolant channel For CC‑0602 indexable inserts Torx key: T8 Torx screw: M2.5x5.5 FAQ Which insert type fits the tool? The KE18TM boring bar is designed for CC‑0602 indexable inserts, which are secured according to the ISO-compatible pocket. Does the bar provide internal coolant delivery? Yes, the KE18TM features an internal coolant channel to feed coolant directly to the cutting edge. What are the main dimensions of the bar? The KE18TM has a 12 mm cutting diameter, 125 mm overall length and a 10 mm shank diameter. Is the cutting direction left‑hand or right‑hand? This variant is specified as left‑hand cutting direction and should be used accordingly. What material is the bar made from? The KE18TM is produced from solid carbide for high rigidity and wear resistance. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of tight tool changeover, precise indexable-insert compatibility and a robust 30 mm shank for stable machining. Order the insert milling cutter directly via Metav Werkzeuge or contact our consultants for application advice. Insert milling cutter S011TM – 12 mm diameter, 30 mm shank (Teknik Makina) The insert milling cutter S011TM is an indexable end mill designed for short-profile and shoulder milling with APMT 0602 inserts, suitable for workshop and light production environments Compatible with APMT 0602 indexable inserts 12 mm cutting diameter for compact milling 30 mm shank for stable clamping Torx M2x4.2 fastening with T6 key Precise indexed cutting for predictable outcomes The Teknik Makina S011TM is built around the industrial standard APMT 0602 indexable inserts, which allow for rapid insert changes and consistent cutting geometry. By using indexable tooling, the cutter delivers repeatable edge positions and predictable wear progression, reducing setup time and minimising scrap. The nominal 12 mm diameter and 2 flutes suit confined machining spaces where controlled chip evacuation and high positional accuracy are required. For purchasers evaluating tool systems, the clear compatibility with Korloy inserts and standard Torx fastening makes tool management straightforward and cost-effective. Stable shank design for low runout and secure clamping A generous 30 mm shank provides the necessary stiffness to reduce deflection in intermittent milling tasks and short shoulder cuts. The combination of a solid shank and a compact cutter body improves dynamic stability, which directly benefits surface finish and dimensional accuracy. Secure clamping is supported by the Torx M2x4.2 screw and the T6 key interface; this arrangement ensures reliable insert retention under moderate cutting forces while enabling quick insert replacement. The tool’s balance between cutter diameter and shank diameter is optimised for repeatable setups on common milling holders and vises. Compact length and geometry engineered for efficient production With an overall length of 120 mm and a cutting length of 10 mm, the cutter is tailored to short-reach milling where access and rigidity matter most. The 90° cutting angle is effective for shoulder milling and producing square shoulders without additional geometry changes, simplifying programme strategies on CNC machines. The lightweight construction (approx. 0.085 kg) supports rapid acceleration and deceleration cycles, which can improve throughput on small-part production runs. For operations focused on efficient turnarounds, the indexable approach reduces per-edge cost compared with solid carbide tools while preserving predictable cycle times. For precise profile milling with Teknik Makina quality, request a tailored quote or technical recommendation from Metav Werkzeuge – contact our specialists at info@metav-werkzeuge.com or call +49 2822 7131930 Technical data SKU: S011TM Manufacturer: Teknik Makina Article: Insert milling cutter for APMT 0602 indexable inserts Core specifications Diameter: 12 mm Shank diameter: 30 mm Cutting length: 10 mm Overall length: 120 mm Number of cutting edges: 2 Weight: 0.085 kg Cutting/lead angle: 90° Materials & special features Torx screw: M2x4.2 Torx key size: T6 Compatible insert manufacturer: Korloy Suitable for: APMT 0602 indexable inserts FAQ Which inserts fit this cutter? The Technik Makina S011TM is designed for APMT 0602 indexable inserts; compatibility with Korloy-manufactured APMT 0602 inserts is specified. Is the Torx screw and key included? The tool uses a Torx M2x4.2 screw with a T6 key interface for fastening; the specification indicates the screw type and key size for replacement or maintenance. What machining tasks is the cutter best suited to? This insert milling cutter is optimised for short-reach shoulder milling and profile work where a 12 mm diameter and 90° cutting angle provide accurate square shoulders and compact machining. How does the shank diameter benefit stability? A 30 mm shank increases stiffness and reduces deflection during intermittent cuts, improving surface finish and dimensional consistency when the Teknı̇k Makina S011TM is used in stable clamping arrangements. Can this cutter be used in small CNC setups? Yes; with its 120 mm overall length and light weight, the S011TM suits compact CNC machines and fixtures where reduced overhang and quick tool changes are advantageous. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Combining a 12 mm shank with a secure T8 Torx fixation and compatibility with APXT 1003 indexable inserts, this cutter offers predictable chip control and robust shoulder milling performance. Benefit from the compact overall length and single-edge geometry for consistent cut quality. Order the S158TM directly via Metav Werkzeuge or ask our consultants for application support. S158TM Shank Cutter – 12 mm shank, for APXT 1003 indexable inserts (Teknik Makina) The S158TM is a precision shank cutter designed for use with APXT 1003 indexable inserts, engineered for shoulder milling and face operations where rigidity and quick insert changes are required. Shank Ø12 mm for rigidity and stability Compatible with APXT 1003 indexable inserts 90° cutting angle for reliable shoulder milling Secured by T8 Torx screw M2.5×5.5 Faster setup and stable performance for repetitive machining The combination of a 12 mm shank and a compact total length of 120 mm reduces overhang and improves stiffness, which in turn raises stability during serial operations. With a single cutting edge, the tool offers predictable chip formation that simplifies process planning and coolant strategy. The practical result is fewer interruptions for rework and a consistently repeatable finish when milling shoulders or faces on medium-duty components. Compatibility and interchangeability that streamline tooling inventories Designed specifically for APXT 1003 indexable inserts and compatible with Korloy-manufactured plates, the cutter reduces the number of specialised holders required across a shop floor. The 90° cutting angle provides a true shoulder cut, eliminating offset passes in many finishing operations. Specification of the Torx fastener as M2.5×5.5 (Torx key T8) clarifies the retention system and supports quick insert clamping and replacement without specialised tooling. Practical advantages for workshop reliability and maintenance At only 0.112 kg and with a cutting length of 27 mm, the shank cutter balances feed responsiveness with manageable mass for reduced spindle load. The straightforward retention via a Torx screw makes insert changes fast, while the standardized insert interface simplifies spare-part stocking. Sourcing this cutter through a distributor that applies a strict quality filter ensures the machining tool meets industrial expectations for repeatability and longevity; the S158TM is designed to integrate into established toolrooms and production cells with minimal adaptation. Contact Metav Werkzeuge for tailored application advice and to source the Teknik Cutting Tools S158TM shank cutter for APXT 1003 assemblies Technical data Article number: S158TM Manufacturer: Teknik Makina Product: Shank cutter for APXT 1003 indexable inserts Key measurements Shank diameter: 12 mm Cutting length (shank): 27 mm Total length: 120 mm Cutting edges: 1 Cutting angle: 90° Weight: 0.112 kg Additional features Compatible with Korloy APXT 1003 inserts Secured with M2.5×5.5 Torx screw Torx key size: T8 FAQ What insert type fits this shank cutter? The cutter accepts APXT 1003 indexable inserts; compatibility with Korloy inserts is specified for straightforward replacement. Which shank diameter is specified for the S158TM? The S158TM has a 12 mm shank diameter, chosen to balance rigidity and accessibility for common holder systems. What is the total length and cutting reach of the tool? Total length is 120 mm with a cutting length (shank) of 27 mm, offering a compact reach for shoulder and face milling. How is the insert secured in the cutter? Insert retention uses a Torx screw specified as M2.5×5.5, tightened with a T8 Torx key for reliable clamping. Is the S158TM suitable for precision shoulder milling? Yes, the 90° cutting angle and shank geometry make it suitable for accurate shoulder milling and operations requiring square faces. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com

Combine the 90° cutting angle, compact 12 mm shank and compatibility with Korloy APXT 1003 indexable inserts for reliable, repeatable milling operations. Order the Teknik Makina shank mill directly via Metav Werkzeuge or consult our specialists for application advice. Schaftfräser for APXT 1003 Indexable Inserts — 90° shank mill, 12 mm The Schaftfräser for APXT 1003 Indexable Inserts is a 90° shank mill designed for secure indexable-insert milling in confined setups and general-purpose machining. 90° cutting angle for axial milling Compatible with Korloy APXT 1003 inserts 12 mm shank diameter for compact toolholders Torx M2.5x5.5 fastening with T8 key High-efficiency 90° milling for stable production The 90° geometry of this shank mill delivers a controlled, axial cutting action that is suited to shoulder milling and profiling where a square shoulder is required. By using an indexable insert system, the tool reduces downtime: inserts are swapped instead of replacing the complete cutter, which lowers running costs and improves uptime. The 90° cutting angle and single-cut arrangement combine to offer predictable chip flow and consistent surface finish, supporting efficient cycle times on serial components. Precise interface and secure clamping for repeatability A 12 mm shank and a total length of 100 mm provide a compact, rigid connection to the toolholder, helping to limit deflection in short-reach operations. The insert is secured with a Torx M2.5x5.5 screw and requires a T8 key, offering a reliable clamping force that maintains insert position under cutting load. This straightforward fastening method simplifies maintenance and ensures repeatability between index changes, which is especially valuable in production environments where consistent tolerances matter. Designed for indexable-insert flexibility and inventory efficiency Compatibility with Korloy APXT 1003 indexable inserts gives access to a wide range of grades and chipbreaker geometries without changing the holder. The shank mill accepts one insert and presents a single cutting edge, which reduces tooling inventory complexity while preserving machining versatility. Given the tool’s 0.097 kg weight and compact profile, it is practical for retrofit into existing setups and for use on smaller milling spindles where balance and clearance are critical. Practical applications and shop-floor advantages This shank mill excels in operations that demand square shoulders, face milling at right angles or light profiling work where insert economics are preferred over solid-tool replacements. The combination of compact dimensions, secure Torx clamping and indexable-insert compatibility supports a lean tooling strategy: fewer tools on the shelf, faster recovery from edge wear and clear process documentation. For purchasers focused on predictable performance and straightforward maintenance, the tool integrates well into scheduled production routines. Contact Metav Werkzeuge today to discuss the Teknik Makina 90° shank mill (SKU S136TM) for Korloy APXT 1003 inserts and to receive tailored application guidance from our advisers. Technical data Article number: S136TM Manufacturer: Teknik Makina Designation: Schaftfräser for APXT 1003 Indexable Inserts ECLASS: 21180806 ETIM: EC011860 Core specifications Shank diameter: 12 mm Cutting length (shank-side): 27 mm Overall length: 100 mm Diameter: 12 mm Number of cutting edges: 1 Cutting angle: 90° Weight: 0.097 kg Special features Compatible inserts: APXT 1003 Compatible insert manufacturer: Korloy Fastening screw: Torx M2.5x5.5 Required key: T8 Suitable for indexable-insert systems FAQ Which indexable inserts fit this shank mill? The shank mill is designed for APXT 1003 indexable inserts; compatibility is specified for Korloy APXT 1003 formats. What is the shank diameter and overall length? The tool has a 12 mm shank and an overall length of 100 mm, offering a compact, rigid profile for short-reach milling. How is the insert secured to the cutter? The insert is fastened with a Torx M2.5x5.5 screw; a T8 key is used for tightening and removal. How many cutting edges does the tool have? This shank mill uses a single cutting edge via the indexable insert system, allowing economical edge replacement. Is the cutter suitable for small toolholders or retrofit applications? Yes — the compact 12 mm shank and light weight make the tool practical for smaller toolholders and retrofit scenarios where clearance and balance are important. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Benefit from replaceable XOMX 0602 inserts, a rigid 12 mm shank and a secure Torx clamping system for reliable machining performance; order the tool direct via Metav Werkzeuge or ask our consultants for specification support. Shank Milling Cutter S625TM — indexable cutter with 12 mm shank and 90° cutting angle (Teknik Makina) A compact Shank Milling Cutter S625TM for indexable-insert milling tasks, designed to accept XOMX 0602 inserts and deliver repeatable 90° cutting performance in production and workshop environments Indexable system for fast insert changes Compatible with SECO XOMX 0602 inserts 12 mm shank for high rigidity Torx M1.8x4 screw, T6 key for secure clamping Consistent, efficient milling with indexable inserts The holder is engineered around an indexable inserts concept, which reduces downtime by allowing rapid replacement of cutting edges instead of regrinding. Fitted for XOMX 0602 format inserts and compatible with inserts from SECO, the tool converts insert life into predictable operating cycles. The 90° cutting angle creates a defined shoulder geometry and simplifies setup for repetitive facing and slotting tasks, while the indexable system supports economic tool management in both small-batch and serial production. Rigid shank and secure clamping for repeatability A 12 mm shank and a substantial overall length of 120 mm provide a balance between reach and stiffness. The cutter uses a Torx clamping screw ( M1.8x4 ) tightened with a T6 key, enabling secure, vibration-resistant fixation of the insert pocket. This combination of shank diameter and screw clamping improves rigidity and repeatability, reducing chatter and ensuring cleaner surface finishes without complex adjustments. The result is a stable toolholder that supports predictable process windows. Clear technical advantages for workshop integration With a 30 mm cutting length and two cutting edges, the design focuses on straightforward machining cycles where fast insert changes are prioritised over solid-end milling logistics. The modest weight of 0.119 kg and standardised mounting dimensions facilitate integration into existing tool magazines and holders. As an indexable-insert solution, the cutter lowers consumable handling time and simplifies inventory: replace worn inserts rather than the entire cutter body, cutting cost per part on repeat operations. Proven supplier and fit for production workflows Produced by Teknik Makina, the component is intended as an industrial toolholder that complements established insert systems and workshop routines. Compatibility with SECO inserts and conventional Torx clamping means technicians can adopt the cutter with familiar maintenance routines. Technical documentation and parts such as the Torx screw and key follow standard workshop practice, allowing for straightforward assembly, inspection and secure storage. For buyers seeking predictable machining performance, this tool offers practical advantages in uptime and serviceability. Contact Metav Werkzeuge for tailored delivery options and to discuss how the S625TM shank milling cutter fits specific machining tasks; our Emmerich-based specialists provide technical guidance and rapid supply coordination Technical data Article number: S625TM Manufacturer: Teknik Makina EClass: 21180806 ETIM: EC011860 Dimensions & weight Shank diameter: 12 mm Cutting length: 30 mm Overall length: 120 mm Diameter: 12 mm Number of cutting edges: 2 Weight: 0.119 kg Cutting angle: 90° Features & compatibility For XOMX 0602 indexable inserts Compatible with SECO inserts Torx screw M1.8x4 Torx key size T6 Indexable-insert milling application FAQ What insert format is required for this cutter? The cutter is designed for XOMX 0602 indexable inserts; Teknik Makina specifies this format for correct seating and performance. Which insert manufacturers are compatible with the tool? Compatibility is confirmed for SECO inserts in the XOMX 0602 size, and the S625TM accepts standard XOMX 0602 geometries. How is the insert secured in the cutter? The insert is fastened using a Torx M1.8x4 screw tightened with a T6 key, providing a secure clamp for stable machining. What are the key dimensions to check for machine mounting? Important dimensions include the 12 mm shank diameter, 120 mm overall length and a 30 mm cutting length—verify these against the machine holder and tool magazine. Is the cutter suitable for high-speed machining? The tool is an indexable-insert holder optimised for repeatable insert changes; suitability for high-speed applications depends on the chosen insert geometry and machine parameters rather than the holder alone. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Benefit from a compact combination of solid carbide construction, internal coolant and a slim 12 mm profile for reliable chip evacuation and steady machining — order the drill bar directly via Metav Werkzeuge or consult our specialists for application advice. Drill Bar KE11TM — SCLC with internal coolant, solid carbide, 12 mm The Drill Bar KE11TM is a solid-carbide SCLC tool with internal coolant, designed as a compact holder for indexable turning geometry and suitable for right-hand operations in precision metalworking. Internal coolant for optimised chip control Solid carbide body for high rigidity Compatible with CC--0602 indexable inserts Slim 12 mm diameter for confined access Consistent cutting performance for small-bore turning The KE11TM delivers stable machining through its monolithic solid carbide construction and compact geometry. A rigid tool body reduces vibration and preserves tool life, which results in more consistent surface finishes and fewer rejects. The slim 12 mm diameter and 125 mm overall length make the tool suitable for confined or deep access areas where larger holders would be impractical. Compatibility with standard insert geometry ensures predictable cutting data and straightforward integration into existing tool setups. Cleaner chips and longer insert life thanks to internal coolant Equipped with internal coolant, this SCLC variant channels lubricant directly to the cutting zone, improving cooling and chip evacuation. The focused coolant flow reduces thermal load on the cutting edge and helps avoid built-up edge, which extends the service intervals for indexable inserts such as CC--0602. For operations that require uninterrupted production, the internal feed improves process stability and reduces the risk of rework caused by heat-related wear. Practical interface and simple assembly for quick tool changes The holder is supplied with standard fixing hardware specified as Torx T8 for the clamping screw and an M2.5×5.5 screw size, allowing rapid, repeatable insert seating. A shank diameter of 10 mm provides a compact yet secure clamping interface for common toolposts and collet systems. With a modest mass of 0.10 kg, the tool minimises inertia while still delivering rigidity, which is beneficial in medium- to light-duty turning and boring tasks where surface quality and dimensional control are priorities. Clear mechanical standards reduce setup time and facilitate reproducible results across shifts. Contact Metav Werkzeuge for tailored technical guidance and to source Teknik Makina’s KE11TM drill bar with internal coolant — professional advice and reliable delivery from Emmerich are available on request. Technical data SKU: KE11TM Manufacturer: Teknik Makina Article designation: E10K SCLCR 06 Dimensions & weights Diameter: 12 mm Overall length: 125 mm Shank diameter: 10 mm Cutting height: 6 mm Weight: 0.10 kg Materials & special features Material: solid carbide Internal coolant: yes Compatible insert type: CC--0602 Cutting direction: right-hand Fixing: Torx T8, screw M2.5×5.5 FAQ What insert type fits this tool? The KE11TM is designed for CC--0602 indexable inserts; matching insert geometry ensures correct seating and expected cutting performance. Is internal coolant available and how does it help? Yes — the tool incorporates internal coolant, which directs lubricant to the cutting zone to improve cooling, chip evacuation and insert life. What are the critical dimensions for fixture planning? Key dimensions are 12 mm diameter, 125 mm overall length and 10 mm shank diameter; these values support fixture selection and reach assessment. Can this holder be used for hard or tough materials? The solid-carbide construction provides rigidity; however, material-specific cutting data and appropriate insert grades should be selected for high-strength or hardened alloys. Which brand manufactures this tool and what is the SKU? This holder is produced by Teknik Makina and listed under SKU KE11TM for ordering and reference. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of a compact, STI-compatible solution that combines reliable clamping and reduced overhang for tighter bores; the slim 10 mm shank and 110 mm overall length improve rigidity and tool life while remaining easy to handle. Order the Technik Makina S10J STIR through Metav Werkzeuge or consult our specialists for application matching. Boring bar S10J STIR — STI for IR/ER indexable inserts, right-hand, by Teknik Makina Boring bar S10J STIR is a right-hand, STI-compatible boring bar designed for use with IR/ER indexable inserts in confined machining setups. Right-hand STI holder for IR/ER inserts 10 mm shank diameter for compact installations 110 mm overall length for restricted bores Low weight 0.079 kg for easier handling Precision where space and repeatability matter The S10J STIR boring solution is engineered for consistent, repeatable performance in constrained environments. Thanks to its STI interface and compatibility with IR/ER indexable inserts, the tool secures inserts with defined geometry and repeatability, reducing set-up time and positional error. This results in improved tolerance control when finishing bores or performing light internal turning operations. The measured design supports stable cutting conditions, which helps to reduce vibration and extend the life of both the insert and the holder. Compact dimensions that increase rigidity and control With a 10 mm shank and 110 mm overall length, this boring bar minimises overhang and improves stiffness at the cut, delivering better surface quality in tight bores. The tool’s 12 mm diameter and 20 mm cutting height are optimised to balance accessibility with mechanical stability. The low mass of 0.079 kg makes handling and inventory management easier while the compact form reduces centrifugal forces at higher spindle speeds. For production environments where space and repeatability are critical, the compact geometry translates directly into fewer rejects and more consistent cycle times. Secure clamping and easy system integration Designed for the STI holding system and compatible with the IR11 clamping variant, the bar integrates smoothly into modular tooling setups. The ISO designation S10J STIR provides a standard reference for toolholders and adapters, simplifying procurement and fixture planning. Installation is straightforward: the profile aligns with established STI interfaces and the right-hand cutting orientation matches common machining sequences. Combined with Metav Werkzeuge’s supply chain and technical advice, the component can be specified into process plans with confidence, reducing downtime and ensuring rapid fitment. For specification assistance or to include the Teknik Makina S10J STIR in a tooling list, contact Metav Werkzeuge for tailored advice or immediate procurement from Emmerich Technical data SKU: K348TM Model designation: S10J STIR Product type: STI for IR/ER indexable inserts Manufacturer: Teknik Makina Dimensions & weight Shank diameter: 10 mm Cutting height: 20 mm Diameter: 12 mm Overall length: 110 mm Weight: 0.079 kg Features & compatibility Right-hand cutting direction Compatible with IR/ER indexable inserts IR11 clamping designation STI holding system interface FAQ Which inserts fit this boring bar? The boring bar S10J STIR is designed for IR/ER indexable inserts and accepts inserts suited to the STI holder configuration; check the insert geometry to match the IR11 clamping profile. Is the S10J STIR suitable for tight bores? Yes — with a 10 mm shank and 110 mm overall length, the bar is tailored for restricted bores where reduced overhang and increased rigidity are required. What is the cutting direction of this tool? The tooling is configured for a right-hand cutting direction, matching common internal turning sequences. How does the compact mass benefit production? The low weight (0.079 kg) and compact design reduce dynamic imbalance and handling effort, contributing to improved cycle consistency and tool-change ergonomics. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Combine the 12 mm diameter, left-hand cutting geometry and robust S10K shank to achieve reliable internal machining and consistent tool life — order the Teknik Makina boring bar directly via Metav Werkzeuge or request guidance from our technical consultants. Boring bar S10K – 12 mm for CC-- 0602 indexable inserts (Teknik Makina) A boring bar designed for internal turning with CC-- 0602 indexable inserts, offering left-hand cutting and compact overall length for tight setups 12 mm diameter for tight internal profiles Compatible with CC-- 0602 indexable inserts Left-hand cutting, 95° cutting angle S10K shank, 10 mm shaft diameter Precise internal profiling with proven insert compatibility The compact boring bar combines a 12 mm cutting diameter with direct compatibility for CC-- 0602 indexable inserts, enabling efficient machining of narrow bores and internal contours. The 95° cutting angle concentrates cutting forces at the insert nose, which helps to maintain stable chip formation and repeatable diameters. Thanks to the S10K shank designation and the 10 mm shaft, the holder provides a rigid connection to the toolpost, reducing deflection during interrupted cuts. These characteristics translate into shorter cycle times and more predictable finishing passes when producing internal features. Secure clamping and straightforward maintenance for uninterrupted production Assembly and service are simplified by the use of a Torx T8 key and an M2.5x5.5 Torx screw for secure insert retention. The standardized Torx drive reduces the risk of cam-out during tightening and ensures consistent clamp force across tool changes, lowering the chance of misalignment. With a cutting height of 20 mm and clearly defined fastening geometry, insert replacement and indexing can be completed quickly, helping to cut downtime in multi-shift operations. The overall light weight (approx. 0.073 kg) and modest 125 mm overall length make handling and fixturing straightforward in compact machines and toolholders. Practical advantages for workshop and production environments Designed for left-hand cutting, the bar is particularly useful where component orientation or machine-tool access dictates a reverse cutting direction. The left cutting direction provides an immediate solution for operations that require that geometry without additional setup. The product’s compact dimensions and the S10K shank allow integration into existing tool systems with minimal adaptation. For businesses seeking predictable performance, the combination of standardised fastenings and insert compatibility reduces variety in spare parts and simplifies inventory management, while the clear technical specification supports repeatable setups across batches. Contact Metav Werkzeuge to discuss the Teknik Makina 12 mm boring bar (SKU K233TM) for CC-- 0602 inserts and arrange tailored technical advice or a specification check. Technical data SKU: K233TM Product type: Boring bar Label: 12mm Bohrstange CC-- 0602 L125mm Manufacturer: Teknik Cutting Tools Core dimensions Diameter: 12 mm Overall length: 125 mm Shaft diameter: 10 mm Cutting height: 20 mm Weight: 0.073 kg Cutting angle: 95° Special features Compatible inserts: CC-- 0602 ISO designation: S10K Cutting direction: left Torx key: T8 Torx screw: M2.5x5.5 FAQ What insert type fits this boring bar? The Teknik Makina boring bar accepts CC-- 0602 indexable inserts designed for internal turning applications. Is the cutting direction standard or reversed? This tool uses a left-hand cutting configuration, intended for operations that require reverse cutting direction. Which shank and shaft sizes does the bar use? The bar features an S10K shank designation with a 10 mm shaft diameter for a rigid toolholder connection. How is the insert secured to the bar? Insert retention is achieved with a Torx screw (M2.5x5.5) tightened using a Torx T8 key for consistent clamp force. What is the SKU for ordering and references? Order or reference the tool using SKU K233TM when enquiring with Metav Werkzeuge. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com

Take advantage of a compact, left-hand tool holder that combines compatibility with TCMT indexable inserts, internal coolant for improved chip control and a rigid, space-saving design; order directly via Metav Werkzeuge or ask our consultants for tailored advice. KA188TM Boring bar (A25R STFCL) – STFC holder for TCMT indexable inserts, left-hand, internal coolant by Teknik Makina The KA188TM is a compact left-hand boring bar designed for precision turning with TCMT indexable inserts and integrated internal coolant, ideally suited to confined toolposts and universal workshop applications Internal coolant through shank Compatible with TCMT indexable inserts Left-hand orientation for interrupted cuts Compact 110 mm overall length Improved process reliability through proven insert compatibility The compact holder is supplied to accept TCMT indexable inserts (reference DC--0702), enabling fast index changes and consistent cutting geometry. Compatibility with widely used insert styles reduces tooling complexity on the shop floor and shortens downtime during changeovers. The integrated coolant feed supports stable cutting temperatures and longer insert life, delivering a measurable gain in tool life and surface finish without additional cooling fittings. Space-saving dimensions that increase setup flexibility A short overall length of 110 mm and a body diameter of 12 mm, combined with a 10 mm shank, make the holder suitable for tight fixtures and multi-tool turrets. The compact proportions preserve rigidity close to the cutting edge, which helps to reduce chatter and improve repeatability when machining small diameters or deep bores. These dimensional properties are especially beneficial for small-batch production and maintenance workshops that require adaptable, accurate tooling. Better chip control and cutting performance for left-hand operations With a 90° cutting angle and a left-hand cutting direction, the holder is optimised for facing and certain interrupted-cut turning tasks where a left-hand approach is advantageous. The internal coolant supply directs fluid to the insert seat, assisting chip evacuation and cooling the cutting zone; this reduces edge wear and supports more consistent machining parameters. For applications sensitive to heat or where chip evacuation is restricted, this arrangement provides clear operational benefits. Practical advantages for daily workshop use Engineered as an ISO-conforming A25R STFCL shank-style holder, the component is lightweight at 0.08 kg yet robust enough for routine turning operations. The standardised interface simplifies stock management and ensures interchangeability across conventional insert grades. The design suits general workshop use, precision maintenance, and production environments seeking economical, dependable toolholding that integrates easily into existing tooling systems. For reliable supply and expert guidance on the Teknik Makina KA188TM, contact Metav Werkzeuge — email info@metav-werkzeuge.com or call +49 2822 7131930 to discuss suitability and availability Technical Data Article number: KA188TM Manufacturer: Teknik Makina Product: Boring bar (STFC for TCMT indexable inserts) ISO designation: A25R STFCL Measurements Diameter: 12 mm Shank diameter: 10 mm Cutting height: 20 mm Overall length: 110 mm Weight: 0.08 kg Cutting angle: 90° Special features Compatible inserts: DC-- 0702 (TCMT) Internal coolant: yes Direction: left-hand Files: 62de7ec733927e49dbf32770, 62de7e1e0aced56449540e88 FAQ Which insert size fits this holder? The holder accepts TCMT-style indexable inserts, referenced as DC-- 0702, which is the intended size for secure seating and reliable cutting performance. Is the coolant routed to the cutting edge? Yes, the design provides internal coolant through the shank so that coolant reaches the insert seat and assists chip evacuation and temperature control. What is the ISO shank designation? The toolholder conforms to ISO designation A25R STFCL, indicating the shank and seat style for standardised mounting. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of a compact, rigid milling solution with a 12 mm shank, internal coolant and compatibility with APMT 0602 indexable inserts to maintain consistent chip control and repeatable setups. Order directly via Metav Werkzeuge or consult our team for application advice and fast delivery. Indexable Insert End Mill (for APMT 0602) by Teknik Makina — 12 mm shank, internal coolant Indexable Insert End Mill (for APMT 0602) is a compact cutter body engineered for versatile milling operations where quick insert changes and reliable coolant delivery are required. 12 mm shank for high rigidity Internal coolant for improved chip evacuation Compatible with APMT 0602 inserts Torx T6 fastening with M1.8x4.1 screw Precision and stability for repeatable results With a 12 mm shank, this cutter body delivers enhanced rigidity that reduces vibration and supports stable tool life during interrupted cuts. The design conserves clamping integrity for shorter setups and predictable results, which translates directly into higher first-pass accuracy on the shop floor. The combination of compact shank diameter and robust construction makes the tool suitable for constrained toolpaths without compromising on stiffness. Improved cooling and chip control for consistent surface quality The integrated internal coolant channel targets the cutting zone, improving lubrication and removing chips from the insert edges. That focused coolant flow helps to keep cutting temperatures lower and reduces built-up edge on the insert, which in turn extends insert life and maintains finish quality. For operations requiring tight tolerances, this targeted coolant delivery supports consistent material removal and reduces the need for secondary finishing. Quick servicing and secure insert retention The cutter accepts APMT 0602 indexable inserts and secures them with an M1.8x4.1 screw tightened using a T6 Torx key, enabling fast index changes and minimal downtime. The three-point cutting configuration contributes to balanced cutting forces and efficient material engagement, while the straightforward fastening system simplifies maintenance routines and tool exchange in production environments. Compact overall length for flexible toolpaths At an 80 mm overall length with a 25 mm cutting length, the tool suits many pocketing and face-milling applications where reach and clearance are balanced. The lightweight construction (approx. 0.061 kg) reduces spindle load during accelerations and is especially useful in high-cycle or automated setups. Compatibility with Korloy inserts broadens sourcing options for inserts and grades, allowing selection according to workpiece material and machining strategy. Contact Metav Werkzeuge for tailored application support and procurement of Teknik Makina cutting solutions — technical consultants are available to advise on insert grades, clamping parameters and delivery options. Technical Data SKU: S004-1TM Manufacturer: Teknik Makina Product type: Indexable insert end mill for APMT 0602 Facts Shank diameter: 12 mm Overall length: 80 mm Cutting length: 25 mm Cutting edges: 3 Weight: 0.061 kg Special features Internal coolant Compatible with APMT 0602 indexable inserts Suitable with Korloy inserts Torx fastening: T6 key Torx screw size: M1.8x4.1 FAQ What inserts does this cutter body accept? The cutter accepts APMT 0602 indexable inserts; the body is specified for APMT 0602 compatibility and works with Korloy insert variants. How is coolant supplied to the cutting zone? Coolant is delivered internally via the integrated internal coolant channel, ensuring targeted fluid flow to the insert edge. Which toolholder or shank diameter is required? The tool has a 12 mm shank, so a holder or collet suitable for a 12 mm shank is required for proper clamping and run-out control. How many cutting edges are active during milling? The cutter is configured with three cutting edges, providing a balance between material removal rate and surface finish. What is the fastening method for the inserts? Inserts are secured with an M1.8x4.1 screw tightened using a T6 Torx key, allowing quick and secure insert changes. Manufacturer / Responsible: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com

Take advantage of a compact milling solution that combines a 12 mm shank, internal coolant and compatibility with APMT 0602 indexable inserts for reliable chip control and consistent cutting performance; order directly via Metav Werkzeuge or consult the team for specification support. Shank cutter for APMT 0602 indexable inserts — 12 mm shank, internal coolant (Teknik Makina) Shank cutter for APMT 0602 indexable inserts designed for industrial milling operations where compact toolholders and effective coolant delivery are required. 12 mm shank diameter for compact setups Internal coolant for improved chip evacuation Compatible with APMT 0602 Korloy indexable inserts 120 mm overall length with 30 mm cutting length Dependable indexable milling for predictable cycle times The shank cutter is engineered to deliver steady performance in small to medium milling centres where repeatability and tool-change simplicity matter. With a 12 mm shank and a total length of 120 mm overall length, the tool is suitable for confined toolholders while still providing a practical reach. The cutter’s two cutting edges support a balanced cut pattern that reduces vibration and contributes to a consistent surface finish — a direct advantage when process stability is a priority. These attributes combine to improve throughput and reduce scrap rates in production environments. Effective cooling and chip management that protect inserts Equipped with internal coolant, the cutter channels coolant directly to the cutting zone to cool the edge and wash chips away from the insert seat. This targeted coolant delivery extends insert life and prevents built-up edge formation, which is especially beneficial when machining alloys or interrupted cuts. The internal supply also supports higher sustained cutting parameters, increasing the likelihood of maintaining a high material removal rate without compromising insert integrity. The result is longer operating intervals between indexings and reduced downtime for insert changes. Clear compatibility and insert guidance for process planners Designed for APMT 0602 indexable inserts and optimised for inserts from Korloy, the tool simplifies procurement and setup in mixed-brand environments. The cutter accepts standard APMT 0602 geometry, enabling selection of grades and chipbreakers to suit aluminium, steel or harder materials depending on the chosen insert. The 30 mm cutting length and 2 cutting edges make it straightforward to specify feeds and speeds: select appropriate insert grade and coolant pressure to match the application and material, and the assembly will offer consistent cutting performance across a range of tasks. Practical mounting and maintenance details for the workshop The cutter uses a secure Torx fastening arrangement with Torx T6 compatibility and a matching screw specification for reliable seat clamping. The compact interface reduces setup time and supports repeatable seating of the indexable insert, helping to maintain concentricity and extend service intervals. Lightweight and easy to handle at approximately 0.121 kg, the tool is practical for fast tool changes and reduces operator fatigue during frequent tool exchanges. Overall, the design supports efficient shop-floor routines and straightforward replacement of wear parts. Contact Metav Werkzeuge for tailored advice on insert grades, coolant configuration and delivery times from Emmerich to ensure immediate integration into existing production setups Technical data SKU: S011-1TM Brand: Teknik Makina Diameter: 12 mm Shank diameter: 12 mm Overall length: 120 mm Cutting length (shank to cutting edge): 30 mm Number of cutting edges: 2 Weight: 0.121 kg Insert type: APMT 0602 Special features Internal coolant supply Compatible with Korloy APMT 0602 indexable inserts Torx key: T6 Torx screw: M1.8 x 4.1 FAQ What insert type does this cutter accept? The cutter is designed for APMT 0602 indexable inserts and is compatible with Korloy insert geometries. How does internal coolant benefit machining with this cutter? Internal coolant delivers cooling and chip evacuation directly to the cutting zone, extending insert life and supporting higher sustained cutting parameters for the cutter. Is the shank size suitable for compact toolholders? Yes, the 12 mm shank suits compact toolholders and systems that require a slim tool interface while still offering a 120 mm overall length. How many cutting edges does the tool have and what is the cutting length? The tool has 2 cutting edges and a cutting length of 30 mm, providing a balanced cut for a range of milling tasks. Which brand manufactures this cutter and what is the SKU? The cutter is manufactured by Teknik Makina and is listed under SKU S011-1TM. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of the combination of internal coolant, a compact 12 mm cutting diameter, and a sturdy 16 mm shank to secure consistent chip control and stable clamping for productive milling. Order the cutter directly via Metav Werkzeuge or consult the technical team for application-specific advice. Shank milling cutter S224-1TM – 12 mm diameter, internal coolant (Teknik Makina) Shank milling cutter S224-1TM designed for APMT 11T3 indexable inserts, providing precision milling with integrated coolant for improved chip evacuation in industrial machining setups. Internal coolant for reliable chip evacuation Compatible with APMT 11T3 inserts (Korloy) 12 mm cutting diameter, 16 mm shank Consistent performance for repetitive milling tasks The cutter body is engineered to maintain a stable cutting process across series production runs. With internal coolant routed to the insert seat, the design promotes effective chip evacuation and temperature control, reducing the risk of built-up edge and preserving insert life. The arrangement for indexable inserts simplifies tool changes and helps keep machine downtime to a minimum, translating directly into higher process reliability on the shop floor. Secure clamping and straightforward maintenance Insert clamping is achieved with a Torx screw system that allows repeatable, low-variation tightening using a T8 key and an M2.5x5.5 screw. The single cutting-edge layout ensures predictable cutting forces and easier balancing compared with multi-edged heads, while the clear access to the fastening elements makes insert replacement rapid and safe. These mechanical details reduce setup time and support consistent cycle times in production. Compact dimensions for rigid toolholding A compact overall length of 85 mm combined with a 16 mm shank provides a favourable stiffness-to-reach ratio for many shop-floor applications. The cutter’s 25 mm cutting-head length balances engagement depth with rigidity, and the low mass of 0.126 kg contributes to reduced spindle load and improved dynamic behaviour. Together these attributes help achieve reproducible surface quality and dimensional stability in short to medium-reach milling operations. Integration with common tooling systems and workflows Designed to accept APMT 11T3 inserts from Korloy, the cutter body fits seamlessly into existing insert inventories and indexable-tool strategies. Its straightforward interface and standard shank diameter make it suitable for conventional holders and adaptors, enabling quick adoption without extensive fixture changes. For machine-specific feeds, speeds and coolant strategies, Metav Werkzeuge’s technical advisers can provide recommendations tailored to the intended application. Rely on Teknik Makina’s robust cutter design and contact Metav Werkzeuge for tailored application advice and supply from Emmerich—email info@metav-werkzeuge.com or call +49 2822 7131930 Technical data SKU: S224-1TM UID: S224-1TM Product type: Shank milling cutter Manufacturer: Teknik Makina Internal coolant: Yes Compatible inserts: APMT 11T3 (Korloy) Facts Cutting diameter: 12 mm Overall length: 85 mm Shank diameter: 16 mm Cutting-head length: 25 mm Weight: 0.126 kg Number of cutting edges: 1 Special features Torx key: T8 Torx screw: M2.5x5.5 Designed for Korloy APMT 11T3 inserts Compact, rigid design for stable milling FAQ Which indexable inserts fit this cutter? The cutter accepts APMT 11T3 indexable inserts; compatibility is specified for Korloy-manufactured versions and similar APMT 11T3 profiles. Is there internal coolant and how does it help? Yes, the cutter features internal coolant to assist chip evacuation and reduce insert temperature, improving tool life and process stability. What are the key dimensions to check for holder compatibility? Check the 16 mm shank and 85 mm overall length; the 12 mm cutting diameter and 25 mm cutting-head length are also relevant for fixture clearance and reach. How is the insert secured and what tool is required? The insert is retained with an M2.5x5.5 Torx screw and serviced with a T8 key for straightforward and repeatable clamping. For which machining tasks is this cutter most suitable? The shank milling cutter S224-1TM is intended for general-purpose milling operations where a compact, indexable solution with coolant support and predictable cutting forces is required. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com

Take advantage of a compact, coolant-fed shank design combined with simple insert compatibility to keep machining cycles reliable and maintenance straightforward; the 12 mm shank and through-coolant feed ensure stable operation and improved tool life. Order directly via Metav Werkzeuge or consult the technical team for application advice. Shank milling cutter for LNMU 0202 indexable inserts (S704TM) — 12 mm shank, internal coolant (Teknik Makina) Shank milling cutter for LNMU 0202 indexable inserts (S704TM) is a dedicated milling tool for installations using LNMU 0202-style indexable inserts; designed for compact set-ups and coolant-fed operations. 12 mm shank diameter for compact tooling Internal coolant for improved chip evacuation Compatible with LNMU 0202 indexable inserts Two cutting edges for efficient material removal Stable clamping and compact geometry for consistent removal rates The tool is engineered around a 12 mm shank and a 100 mm overall length, providing a compact footprint for tight setups while maintaining sufficient reach for many common operations. The 30 mm cutting length and two cutting edges support a balanced cut, which reduces chatter and contributes to a predictable surface finish. With the indexable system fitted to a robust shank, users gain fast replacement cycles and consistent cutting geometry without resorting to solid end mills for every operation. This translates into steadier cycle times and reduced machine downtime in batch production. Coolant-through design that protects inserts and improves finishes A central design advantage is the internal coolant supply directly to the insert seating area, which assists effective chip evacuation and local temperature control at the cutting edge. Cooler cutting conditions extend insert life and help produce more reliable surface integrity on the workpiece. Combined with indexable inserts, the through-coolant arrangement makes maintenance intervals more predictable and reduces the frequency of unscheduled stops for regrinding or premature tool changes, improving overall process economics. Rapid insert change and secure fastening for production environments Insert retention uses a Torx T6 drive with an M1.8x4.1 screw, allowing quick, tool-shop-friendly insert changes while ensuring secure clamping during heavy engagement. The low tool mass (0.112 kg) reduces additional spindle load and can help maintain balance at higher spindle speeds compared with heavier alternatives. The design supports easy access to the fastening screw and straightforward torque control for repeatable clamp force, which is essential for maintaining insert position and repeatability in serial production. Procurement simplicity and dependable supply from a specialised partner Sourcing this indexable shank cutter through Metav delivers the benefits of a specialist distributor with deep inventory and support capabilities. Metav’s offering is backed by broad product coverage and an established logistics base in Emmerich, helping to simplify procurement and reduce supplier complexity. For customers seeking a compromise between compact tool geometry and coolant-fed performance, this cutter fits into modular tooling strategies and supports efficient workshop workflows. Contact Metav Werkzeuge in Emmerich to discuss whether the Teknik Cutting Tools shank milling cutter S704TM matches specific application requirements or to arrange technical clarification via info@metav-werkzeuge.com or +49 2822 7131930 Technical data SKU: S704TM Manufacturer: Teknik Makina Product type: Shank milling cutter Compatible inserts: LNMU 0202 (Tungaloy) Shank diameter: 12 mm Overall length: 100 mm Cutting length: 30 mm Number of cutting edges: 2 Internal coolant: Yes Torx key: T6 Torx screw: M1.8x4.1 Weight: 0.112 kg Core data Diameter: 12 mm Overall length: 100 mm Cutting length: 30 mm Number of edges: 2 Weight: 0.112 kg Special features Internal coolant feed Compatible with LNMU 0202 indexable inserts Torx T6 fastening system with M1.8x4.1 screw Compact shank for tight setups Lightweight construction for reduced spindle load FAQ Which inserts are compatible with this cutter? The shank milling cutter S704TM accepts LNMU 0202 indexable inserts and is noted as compatible with inserts from Tungaloy. How does the internal coolant affect tool life? Internal coolant supplies lubricant and cooling directly to the cutting zone on the Teknik Makina shank milling cutter S704TM, which helps reduce thermal stress on the insert and can extend insert life while improving surface finish. What are the key dimensions to check before ordering? Key dimensions include a 12 mm shank diameter, 100 mm overall length and 30 mm cutting length; the tool has two cutting edges and weighs 0.112 kg (SKU S704TM). How are inserts secured and changed? Inserts are fastened with a Torx T6 screw (size M1.8x4.1), allowing safe, repeatable clamping and quick replacement during routine maintenance. Manufacturer / Responsible: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of a robust combination of stability, coolant-assisted chip control and flexible indexable insert compatibility to keep machining cycles efficient and repeatable; order directly via Metav Werkzeuge or consult the technical team for application advice. Schaftfräser S087TM – 12 mm shank end mill with internal coolant for LNMX 0402 indexable inserts (Teknik Makina) The Schaftfräser S087TM is a 12 mm shank milling tool engineered for secure toolholding and reliable insert-based milling operations with LNMX 0402 indexable inserts, suitable for CNC and workshop environments. *12 mm shank for stable toolholding *Internal coolant for improved chip evacuation *Compatible with LNMX 0402 indexable inserts *40 mm cutting length for deeper engagements *Three cutting edges for balanced performance Faster cycles through stable toolholding and predictable removal rates A robust 12 mm shank and a 100 mm total length deliver the rigidity required for repeatable machining cycles. The combination of a moderate 40 mm cutting length and three cutting edges balances material removal rate with surface quality, reducing chatter and rework. For indexable-insert systems this translates into fewer interruptions for tool changes and consistent component tolerances, which supports higher machine utilisation and predictable production throughput. Improved cooling and insert handling for longer tool life The integrated internal coolant channel directs cutting fluid close to the cutting zone, improving chip evacuation and cooling the insert contact area to reduce thermal stress. Designed for LNMX 0402 indexable inserts and compatible with Korloy types, the system enables fast insert indexing and replacement using the Torx T6 key and M1.8x4.1 fixing screw. These features reduce downtime during maintenance and help preserve insert geometry, which in turn maintains surface finish and dimensional accuracy over longer runs. Versatile, lightweight design for workshop efficiency With a mass of only 0.07 kg, the shank cutter is straightforward to handle during set-up while its indexable design minimises inventory complexity by standardising on LNMX 0402 inserts. The combination of a solid shank, internal coolant and standardised fixing hardware makes the tool suitable for a wide range of milling operations where insert-based solutions are preferred for quick serviceability and cost-effective cutting edge replacement. For process-focused applications that require coolant-fed indexable milling, contact Metav Werkzeuge to discuss the Teknik Makina S087TM and how it fits individual production needs; Metav’s specialists in Emmerich can advise on compatibility and supply – info@metav-werkzeuge.com or +49 2822 7131930 Technical data SKU: S087TM Manufacturer: Teknik Makina Product type: Schaftfräser Compatible inserts: LNMX 0402 (Korloy) Core specifications Shank diameter: 12 mm Total length: 100 mm Cutting length: 40 mm Number of cutting edges: 3 Weight: 0.07 kg Features & assembly Internal coolant Torx key: T6 Torx screw: M1.8x4.1 For indexable inserts FAQ Which indexable inserts fit this cutter? The cutter accepts LNMX 0402 indexable inserts; it is listed as compatible with Korloy LNMX 0402 types for straightforward sourcing and replacement. How does the internal coolant improve performance? Internal coolant channels deliver fluid directly to the cutting zone on the S087TM, improving chip evacuation and thermal control, which helps to extend insert life and maintain surface finish. What fixing hardware is required to secure the inserts? Insert retention is achieved with a Torx fixing screw (M1.8x4.1) tightened with a Torx T6 key for secure and repeatable clamping. What are the main dimensions to consider for setup? Key dimensions are a 12 mm shank diameter, 40 mm cutting length and 100 mm total length, which together determine reach, rigidity and compatibility with holders. Is the tool suitable for automated tool changes? The indexable insert system with Torx fastening and standardised insert geometry is well suited to workshop and CNC environments where rapid insert replacement is required. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of the 12 mm cutting diameter and internal coolant to increase milling efficiency and finish quality, while the robust 16 mm shank and 85 mm overall length provide stable mounting and accessibility in compact setups; order directly via Metav Werkzeuge or consult our specialists for insert recommendations. Insert milling cutter S397TM — 12 mm diameter, internal coolant, Teknik Makina The insert milling cutter S397TM is a shank-style milling body engineered for VDKT 11T2 indexable inserts, offering internal coolant and a compact 85 mm overall length for precise milling in confined setups 12 mm cutting diameter, 16 mm shank Internal coolant for improved chip evacuation Compatible with VDKT 11T2 inserts (Korloy) Total length 85 mm, 25 mm effective cutting length Increase throughput with targeted cooling and compact rigidity The combination of internal coolant and a compact geometry ensures consistent chip removal and temperature control at the cutting zone. Internal coolant channels deliver cutting fluid close to the insert seat, which reduces thermal load and helps maintain cutting-edge life; this results in more stable processes and fewer tool changes per shift. The 12 mm cutting diameter together with the 16 mm shank provides a rigid connection to the spindle, reducing vibration and improving surface finish. For production environments seeking measurable productivity gains, this configuration supports higher feed rates while preserving dimensional accuracy. Reliable insert system and simple maintenance for continuous operation Designed specifically for VDKT 11T2 indexable inserts and compatible with Korloy makes and grades, the tool body simplifies tooling inventories and insert sourcing. The insert clamping uses a Torx T8 driver and M2.5x5.5 screws for secure, repeatable seating; fast, consistent insert changes minimise downtime. The S397TM’s single-cutting-edge arrangement reduces cutting forces in interrupted cuts and is straightforward to set up. Clear identification of insert type and compatible suppliers streamlines procurement and ensures that the cutter performs predictably in mixed-workshop environments. Practical handling, tool life considerations and workshop integration With a total length of 85 mm, an effective cutting length of 25 mm and a lightweight build of 0.11 kg, the tool is easy to mount and manoeuvre in tight fixtures while still offering solid performance. The single cutting edge aids chip segmentation and is suited to light- and medium-duty milling tasks where controllable chip flow is important. Regular inspection of clamping screws and the coolant passages will keep service intervals long and machine uptime high. For assembly and spare parts planning, note the shank diameter and the Torx screw type to ensure correct holders and drivers are available on the shop floor. For reliable, cooled milling in compact setups, contact Metav Werkzeuge to discuss the Teknik Makina S397TM insert milling cutter and receive tailored advice on insert grades and holder compatibility. Technical data Article number: S397TM Manufacturer: Teknik Makina Product type: Insert milling cutter (shank) Designation: for VDKT 11T2 Indexable Inserts Diameter: 12 mm Shank diameter: 16 mm Total length: 85 mm Cutting length: 25 mm Weight: 0.11 kg Number of cutting edges: 1 Internal coolant Compatible inserts: VDKT 11T2 Compatible insert manufacturer: Korloy Torx key: T8 Clamping screw: M2.5x5.5 FAQ Which insert type fits this cutter? The cutter accepts VDKT 11T2 indexable inserts; the body is designed for this insert geometry and seat. Is the cutter supplied with inserts or screws? The listing describes the tool body S397TM; inserts and spare screws are supplied separately to allow selection of the appropriate grade. How does internal coolant affect performance? Internal coolant improves chip evacuation and reduces thermal load at the cutting edge, extending insert life for the S397TM insert milling cutter. What shank holders are required? A holder matching the 16 mm shank diameter is required; ensure clamping systems support the shank and the intended spindle interface. Can the cutter be used for face milling and slotting? The tool is suitable for light to medium-duty face milling and slotting operations where a 12 mm cutting diameter and a 25 mm cutting length are appropriate. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of precise right‑hand parting with a 2 mm cutting width and 16 mm maximum cutting depth for controlled chip evacuation and reliable cycle times; combine compact dimensions and robust clamping for consistent production. Order the holder via Metav Werkzeuge or consult our technical advisors for application matching. Teknik Makina Parting clamp holder D658TM — right‑hand, 2 mm cutting width The parting clamp holder is designed for controlled right‑hand grooving and parting operations with indexable inserts, delivering compact stability for workshop and light‑industrial turning applications. Right‑hand cutting for conventional setups 2 mm cutting width for narrow grooves Max parting depth 16 mm Compatible with Korloy 2C MGM inserts Precision where narrow grooves matter The holder provides a focused solution when space on the turned workpiece is limited: the 2 mm cutting width makes fine parting and narrow‑groove operations repeatable while the right‑hand cutting geometry ensures predictable chip flow. By concentrating cutting forces in a small contact zone, the tool reduces vibration and permits consistent surface finish in serial turning and finishing operations. This benefit is particularly relevant for workshops machining small components where dimensional control and minimal material loss are required. Stable construction for reliable cycles With a 12 mm clamping head and a compact 125 mm overall length, the design promotes rigidity without adding unnecessary overhang. The reduced mass (0.162 kg) lowers centrifugal load at higher spindle speeds and helps maintain concentricity during short, repetitive cuts. The clamping concept secures the insert firmly, translating into stable cuts and extended insert life. These mechanical advantages support improved uptime and predictable tool replacement intervals, which in turn aid process planning and cost control. Fast integration and proven compatibility Compatibility with Korloy 2C MGM indexable inserts and the ISO 1212 holder designation simplifies procurement and tool‑life management across mixed fleets. The mount accepts the 2C‑R MGM bar format, allowing straightforward retrofitting into existing tool posts and reducing setup time at the turret. For production planners this means fewer special holders to stock and faster changeovers between parting operations, yielding a measurable improvement in shopfloor throughput without compromising precision. For application advice or to confirm suitability of the Teknik Makina parting clamp holder D658TM with existing Korloy inserts, contact Metav Werkzeuge at info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: D658TM Manufacturer: Teknik Makina Core data Cutting head width: 12 mm Cutting width: 2 mm Maximum parting depth: 16 mm Overall length: 125 mm Weight: 0.162 kg Cutting direction: right Special features Compatible with Korloy 2C MGM inserts ISO designation: 1212 Mounting bar designation: 2C‑R MGM Suitable for indexable insert parting operations FAQ Which insert types fit this holder? The holder is compatible with Korloy 2C MGM indexable inserts and accepts the 2C‑R MGM mounting bar format; using the specified insert type ensures correct clamping and cutting performance. What is the maximum cutting depth for the holder? Maximum parting depth is 16 mm, which balances effective material removal with rigidity for controlled groove profiles. Is the tool suitable for left‑hand cutting? No, the design is for right‑hand cutting only; left‑hand operations require a dedicated left‑hand holder. What does the ISO 1212 designation indicate? The ISO 1212 designation describes the holder form and interface for indexable insert parting tools, simplifying selection and compatibility checks across tool systems. How compact is the holder for turret mounting? With an overall length of 125 mm and a 12 mm clamping head, the holder is compact and well suited to minimising overhang on standard turrets for short to medium parting cycles. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of the 72.5° cutting geometry and ISO SVVBN 1212 format to ensure stable, repeatable turning operations; the compact 110 mm overall length and 12 mm shank make it straightforward to integrate into existing toolposts. Order directly via Metav Werkzeuge or consult the specialists for application advice. Klemmhalter SVVBN 1212 – SVVBN for VBMT Indexable Inserts by Teknik Makina, 72.5° approach, 110 mm length Klemmhalter SVVBN 1212 is a compact tool holder designed for external turning with VBMT indexable inserts, combining precise geometry with standardised shank dimensions for reliable workshop use 72.5° cutting geometry for precise profiling ISO SVVBN 1212 designation for standard fit Compatible with VBMT 1103 indexable inserts 12 mm shank width and 110 mm overall length Stable cutting geometry for consistent surface quality The holder’s 72.5° approach angle is engineered to direct cutting forces evenly across the insert flank, reducing chatter and improving surface finish on external turning tasks. As a purpose-designed tool holder for indexable inserts, it supports controlled chip formation and predictable tool life, which translates into fewer interruptions on the shop floor and more consistent part tolerances. The orientation of the cutting edge is particularly advantageous for profiling and finishing operations where a defined entry angle reduces burr formation and downstream rework. Compact dimensions that simplify toolset planning With an overall length of 110 mm and a shank width of 12 mm, the holder fits common turret and toolpost arrangements without obstructing adjacent tools. The SVVBN 1212 ISO designation indicates the holder geometry and nominal cross-section, making it straightforward to match with existing tool carriers and adapters. The compact head width and a defined cutting height contribute to a low-offset setup that helps maintain rigidity; this minimises deflection and preserves the intended cutting geometry even under moderate feeds. Compatibility, handling and workshop benefits Designed for use with VBMT 1103 inserts, the clamping arrangement allows secure retention and repeatable index changes, cutting setup time and simplifying inventory management through standardised insert sizes. The holder’s light mass (approx. 0.129 kg) eases handling during tool changes while preserving sufficient mass for vibration damping in many turning applications. Supplied in a standard SVVBN configuration, the component supports quick retrofitting and reduces the need for bespoke toolholders, helping to streamline procurement and reduce downtime. Contact Metav Werkzeuge for tailored application advice and prompt supply from Emmerich: info@metav-werkzeuge.com / +49 2822 7131930 Technical Data Article number: D131TM Manufacturer: Teknik Makina SKU: D131TM ISO designation: SVVBN 1212 Facts Overall length: 110 mm Shank width: 12 mm Cutting head width: 6 mm Cutting height: 25 mm Cutting angle: 72.5° Weight: 0.129 kg Special features Compatible inserts: VBMT 1103 Secondary designation: SVVBN for VBMT Indexable Inserts Toolholder type: clamping holder for indexable inserts Mounting reference: J11 FAQ What insert type fits this holder? The holder is specified for VBMT 1103 indexable inserts; the SVVBN geometry ensures correct seating and clamping for this insert format. Is the holder suitable for finishing passes? Yes, the 72.5° approach angle and rigid SVVBN configuration are optimised for finishing and profiling where controlled contact and reduced vibration are important. Which ISO designation identifies the shank and head geometry? The tool is designated SVVBN 1212, indicating the nominal shank dimensions and head form for compatibility with standard fixtures. Can this holder be used in standard toolposts without modification? The 12 mm shank and the ISO format are intended for standard turrets and toolposts; however, final fit depends on the specific machine carrier and adaptor used. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of the M5 thread and 12 mm overall length for secure, space‑saving fastening — order the locking screw directly via Metav Werkzeuge or ask our consultants for matching parts and supply. Locking screw TH512TM — M5 thread, 12 mm overall length by Teknik Cutting Tools A compact locking screw for secure fixation in tight assemblies, compatible with measuring instruments and adjustable with a 2 mm Allen key Compact M5 thread for tight assemblies 12 mm overall length for space-saving fixation Compatible with 2 mm Allen key for simple adjustment Lightweight 0.1 kg for easy handling Secure, compact fastening where space matters The M5 thread combined with a 12 mm overall length gives a compact yet secure solution for applications where clearance is limited. As a small locking fastener, it provides consistent clamping without protruding components, helping to maintain neat assembly geometry and minimise interference with moving parts. The restrained form factor makes this component suitable for instrument housings, small fixtures and measurement devices where precision and repeatability are required. Effortless installation and precise adjustment Designed for quick adjustment using an Allen key 2 mm, the fastener permits reliable tightening and re‑adjustment without specialised tools. The simple interface reduces assembly time and helps maintain consistent torque application across multiple units, which supports efficient production workflows and straightforward in‑service maintenance. For workshop environments that prioritise speed and accuracy, this locking element streamlines small‑part handling and reduces the risk of improper fastening. Integration, handling and supply reliability With a nominal weight of 0.1 kg, the component is easy to handle during assembly and stocking. Supplied by a recognised manufacturer, the item fits into established parts management systems and supports predictable stock rotation. Choosing a compact, standard‑thread locking screw like this helps to keep spare‑part lists short and procurement transparent, contributing to lower downtime and dependable workshop operation when replacements are required. Choose the Teknik Cutting Tools M5 locking screw TH512TM for compact, reliable fastening — contact Metav Werkzeuge in Emmerich for tailored advice and dependable supply. Technical Data SKU: TH512TM Product: Locking screw Manufacturer: Teknik Makina Facts Thread: M5 Overall length: 12 mm Weight: 0.1 kg Special features Compatible with measuring calipers and small fixtures Space‑saving, compact design Adjustable with 2 mm Allen key FAQ Which Allen key size is required for adjustment? The locking screw TH512TM is adjusted with a 2 mm Allen key for installation and re‑tensioning. What are the thread and length specifications? The fastener features an M5 thread and a 12 mm overall length as standard for compact applications. Is this component suitable for measuring calipers and similar instruments? Yes, the TH512TM locking screw is compatible with measuring calipers and small measurement fixtures where compact locking elements are needed. How is the screw installed and re‑adjusted? Installation and adjustment are performed with a 2 mm Allen key; the design supports quick tightening and straightforward re‑setting of the clamp position. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com