Take advantage of the combination of solid carbide construction, TiN coating and self‑centring geometry to recover damaged threads quickly and reliably; order the tool directly via Metav Werkzeuge or consult the team for application advice. M10 Tap Removal Drill, solid carbide, TiN-coated – TECWERK The M10 Tap Removal Drill is a solid‑carbide, TiN‑coated, self‑centring tool designed for boring out broken HSS and HSS‑Co taps in production and maintenance settings. Solid carbide, TiN-coated surface Self‑centring with three flutes Straight flutes for controlled chip evacuation Accurate recovery of damaged threads for minimum rework When a tap fractures in a workpiece, controlled material removal is essential to preserve the component’s thread form. The M10 Tap Removal Drill provides a rigid, vibration‑resistant cutting body thanks to its solid carbide construction, which reduces axial run‑out during entry. The self‑centring geometry positions the tool accurately on the broken tool, lowering the risk of enlarging or damaging the surrounding thread. This targeted approach minimises scrap rates and reduces the need for subsequent corrective machining. Durable cutting performance that extends tool life Long tool life and consistent performance are achieved by combining a wear‑resistant TiN coating with a high‑grade carbide substrate. The coating reduces friction at the cutting interface and improves heat resistance under intermittent cutting conditions, while the carbide core preserves cutting edge stability. The tool’s straight flutes and 3‑flute design ensure predictable chip formation and evacuation when removing the fractured tap material, which contributes to safer, cleaner cutting and fewer stoppages for clearing chips. Designed for fast setup and reliable clamping in workshop environments A cylindrical shank with Ø 10 mm provides secure clamping in common collets and drill chucks, allowing quick tool changes on maintenance benches and small machining centres. The core bore Ø 8.5 mm and chip length 25 mm are engineered for efficient penetration into the broken tap while keeping chip flow manageable, reducing the need for repeated clearing. Supplied in single units, the tool is suited to maintenance and repair operations where a precise, ready‑to‑use solution is required for tap extraction tasks. For secure, high‑precision tap recovery with TECWERK’s solid‑carbide, TiN‑coated M10 tap removal drill, contact Metav Werkzeuge in Emmerich at info@metav-werkzeuge.com or +49 2822 7131930 to confirm suitability and arrange supply and technical advice Technical data Article number: 2000867720NW Product name: Gewindeausbohrwerkzeug M10 VHM TiN Z.3 TECWERK Packaging unit: 1 Facts Shank diameter: 10 mm Core bore diameter: 8.5 mm Chip length: 25 mm Flute count: 3 Special features Solid carbide (VHM) TiN coating Cylindrical shank Self‑centring design Straight flutes For boring out broken HSS and HSS‑Co taps FAQ How does the tool prevent damage to the original thread? The tool’s self‑centring geometry and rigid solid carbide body position and stabilise the cutter, so material is removed concentrically and the original thread form is preserved as far as possible. Which materials can be addressed with this extractor? This tool is specified for the removal of fractured HSS and HSS‑Co taps; the geometry and carbide construction are optimised for those hard tool steels. What clamping systems are compatible with the shank? The 10 mm cylindrical shank is compatible with standard collets and drill chucks commonly used in toolrooms and maintenance shops. How do the straight flutes affect chip control during extraction? Straight flutes produce predictable chip fragments and aid manual chip clearing, reducing the risk of jammed chips when boring into broken tap material. Is the tool supplied ready for immediate use? The product is supplied as a single unit and is ready for clamping and use; standard safe machining practices should be followed. Manufacturer / Responsible: NORDWEST Handel AG, Robert‑Schuman‑Straße 17, 44263 Dortmund

The combination of solid carbide construction and TiN coating delivers precise, durable removal of fractured taps while the self‑centring, straight‑fluted geometry reduces the risk of secondary damage; order this thread‑extraction tool directly via Metav Werkzeuge or consult our specialists for application support. Thread-extraction drill M12, solid carbide, TiN‑coated — TECWERK The Thread-extraction drill M12 is a specialised solid‑carbide tool for safely drilling out broken HSS and HSS‑Co taps in maintenance and production environments. Solid carbide construction TiN coating for extended wear Self‑centring, straight‑fluted design 3 cutting edges with 30 mm cutting length Precise extraction that reduces rework and downtime Designed for targeted removal of fractured taps, the tool’s solid carbide body combined with a TiN surface gives controlled cutting action and longer life than standard tool steels. The self‑centring geometry ensures accurate engagement with the broken fragment, while the straight flutes guide chips away from the workpiece in a predictable manner. These attributes translate into fewer intervention cycles, less risk of workpiece scrap and a more reliable repair process for production lines and maintenance shops alike. Robust design for consistent process windows Durability and process reliability are achieved through material and geometry: solid carbide resists chipping during interrupted cuts, and the TiN layer lowers friction for improved wear resistance. The tool features a 30 mm cutting length and a core hole Ø 10.2 mm, giving sufficient engagement to evacuate material from the fractured tap. A shank Ø 12 mm ensures compatibility with common holders, so the specification supports predictable running behaviour and reduced tool change frequency in demanding applications. Easy integration and clear application scope The cylindrical shank accepts standard chucks, simplifying fixture set‑up, while the straight‑fluted profile supports consistent chip evacuation when working down into a broken tap. Intended specifically for the removal of fractured HSS and HSS‑Co taps, the drill is suited to workshop repair, toolroom refurbishment and spot‑repair tasks on production equipment. For detailed application notes and best‑practice setup, Metav Werkzeuge provides documentation and consulting to match the tool to the task without unnecessary guesswork. For application advice or a tailored quotation for the TECWERK thread‑extraction drill, contact Metav Werkzeuge in Emmerich — phone +49 2822 7131930 or eMail info@metav-werkzeuge.com — our consultants will advise on selection and delivery from stock. Technical data Article number: 2000867721NW Product name: Thread‑extraction drill M12, TECWERK Brand: TECWERK Material: solid carbide (VHM) Coating: TiN Packaging unit: 1 Facts Shank diameter: 12 mm Cutting length: 30 mm Number of cutting edges: 3 Core‑hole diameter: 10.2 mm Special features Cylindrical shank Self‑centring geometry Straight flutes TiN coated for wear resistance For removal of broken HSS and HSS‑Co taps FAQ What materials can be worked with this tool? The Thread‑extraction drill M12 is intended for the removal of fractured HSS and HSS‑Co taps and is specified for those tool steels. How does the TiN coating help in tap removal? The TiN coating on the TECWERK thread‑extraction drill reduces friction, improves wear resistance and extends the service life under interrupted cutting conditions typical when machining broken taps. What holder size is required for safe clamping? Use a holder or chuck compatible with a shank Ø 12 mm; correct clamping ensures concentric running and reliable extraction performance with the TECWERK tool. How deep will the drill cut into a broken tap? The tool provides a 30 mm cutting length, which offers sufficient engagement for secure material removal from most fractured tap situations encountered in workshop repair. Which article number should be ordered for this tool? Order the TECWERK thread‑extraction drill under Article number 2000867721NW for the M12 version. Manufacturer/Responsible: NORDWEST Handel AG, Robert‑Schuman‑Straße 17, 44263 Dortmund

Take advantage of the combination of solid carbide construction, TiN coating and a self‑centring, straight‑fluted geometry to remove broken taps reliably and reduce downtime; order the thread extraction drill directly via Metav Werkzeuge or consult the technical advisors if assistance is required. Thread extraction drill M4 — solid carbide, TiN‑coated, 3‑tooth (TECWERK) The Thread extraction drill M4 is a purpose‑built solid carbide tool for safe drilling out of broken HSS and HSS‑Co taps in workshop and production environments. Solid carbide, TiN‑coated cutting head Self‑centring, straight‑fluted design Optimised for broken HSS and HSS‑Co taps Three‑tooth geometry for efficient chip evacuation Fast and reliable removal of broken taps for uninterrupted workflow The drill is designed for targeted extraction of fractured taps and threaded tools, combining a solid carbide body with a TiN coating for extended edge life. The self‑centring geometry reduces the need for pre‑alignment, which shortens setup time and lowers the risk of further thread damage. As a result, downtimes are reduced and rework is minimised, supporting continuous production and predictable maintenance cycles. Precision cutting and controlled chip formation for safe operation A three‑tooth geometry and straight flutes provide consistent chip formation and evacuation through a dedicated chip length of 15 mm, which helps avoid clogging in blind holes. The cylindrical shank with a 6 mm diameter gives stable clamping in standard toolholders, while the 3.3 mm core hole dimension ensures a compact cutting core for precision guidance. Together, these attributes enable a clean extraction process with less force transfer to the workpiece. Suitable cutting speeds and versatile application range The tool is rated for use across a practical speed range of 1,500–3,500 rpm, with an operational recommendation of about 2,100 rpm for many typical M4 cases. That flexibility permits adaptation to different machine capabilities and material conditions. Specifically made for dealing with broken HSS and HSS‑Co taps, the tool is also appropriate wherever a robust, high‑precision solid carbide drill is required for corrective maintenance tasks in metalworking shops. Practical benefits for workshop and service technicians Thanks to the combination of TiN coating and solid carbide substrate, the tool offers improved wear resistance and easier cutting performance compared with uncoated alternatives. The straightforward geometry simplifies handling and reduces the learning curve for maintenance teams. For complex cases or unusual materials, Metav’s product specialists can provide application guidance and machining parameter suggestions to ensure effective use in everyday workshop practice. Contact Metav Werkzeuge for personalised machining advice or to order the TECWERK thread extraction drill; Metav’s specialists are available to clarify technical details and recommend the optimal working speeds and clamping options. Technical Data Article number: 2000867716NW Manufacturer: TECWERK Packaging unit: 1 Facts Shank Ø: 6 mm Core hole Ø: 3.3 mm Chip length: 15 mm Number of teeth: 3 Speed range: 1,500–3,500 rpm Recommended speed: 2,100 rpm Special features Solid carbide (VHM) TiN‑coated Cylindrical shank Self‑centring Straight‑fluted Designed for drilling out broken HSS and HSS‑Co taps FAQ What materials is this tool intended for? The TECWERK thread extraction drill M4 is designed specifically for removing broken HSS and HSS‑Co taps and is suited to standard steel workshop applications where corrective drilling of threaded tools is required. Which spindle speed should be used for best results? A practical operating range for the tool is 1,500–3,500 rpm; a typical recommendation for many M4 applications is approximately 2,100 rpm to balance cutting performance and tool life. How does the TiN coating benefit the tool? The TiN coating on the solid carbide body increases wear resistance and improves sliding properties, resulting in more consistent cutting performance and longer tool life during extraction tasks. Is a special holder required for the 6 mm shank? The cylindrical shank with a 6 mm diameter fits standard collets and chucks; secure clamping in an appropriate holder is advised to maintain concentricity during drilling. Manufacturer / Responsible: NORDWEST Handel AG, Robert‑Schuman‑Straße 17, 44263 Dortmund

Take advantage of a durable, carbide construction combined with a TiN wear layer and precise three‑flute geometry for dependable removal of broken HSS and HSS‑Co taps; order via Metav Werkzeuge or consult the technical team for integration into existing toolsets. Tap Drill‑Out Tool M20 – Solid Carbide, TiN‑coated, 3‑flute (TECWERK) The Tap Drill‑Out Tool M20 is a solid‑carbide, TiN‑coated, three‑flute rotary extraction tool designed to remove broken HSS and HSS‑Co thread taps in M20 applications with secure clamping and controlled chip evacuation Solid carbide with TiN coating Self‑centring, straight‑fluted geometry 3‑flute design for reliable chip control Cylindric shank Ø 18 mm for secure clamping Engineered for reliable tap extraction and process safety The solid‑carbide construction paired with a TiN coating creates a hard, wear‑resistant cutting edge that reduces abrasion when machining hardened tap remnants. This combination yields consistent cutting performance and extended tool life compared with uncoated alternatives. In practice, the tool’s self‑centring design simplifies alignment with damaged threads, reducing the risk of off‑centre cuts and minimising secondary operations caused by misalignment. Consistent cutting performance and controlled chip flow A three‑flute layout with straight flutes provides balanced cutting forces and predictable chip formation, which is essential when extracting broken taps where stability is limited. The defined chip length 50 mm aids in chip evacuation without clogging the flute; this reduces the chance of re‑cutting chips and supports steady progress through the core. The result is a measurable improvement in cycle reliability and fewer interrupted operations on the shop floor. Designed for straightforward integration in workshop environments The cylindric shank Ø 18 mm ensures compatibility with common chucks and collet systems used in professional machining centres, enabling secure clamping and repeatable concentricity. The tool is optimised to work specifically for extracting fractured HSS and HSS‑Co taps from M20 threads, so set‑up time is reduced and process predictability is increased. For procurement and logistics, Metav Werkzeuge supplies the tool with clear stock and delivery handling for industrial buyers. Durability, maintenance considerations and predictable tool life The combination of solid carbide and TiN coating provides improved heat resistance and surface hardness, which together lower wear rates under interrupted cutting conditions typical of tap removal. The core hole Ø 17.5 mm specification assists in preparing an appropriate pilot condition where required, helping to limit stress on the cutting edges. With controlled use and correct clamping, this tool delivers reproducible service intervals and predictable maintenance planning for precision workshops. For integration advice or to confirm compatibility with existing machines, contact Metav Werkzeuge for expert guidance on TECWERK’s solid‑carbide M20 tap drill‑out tool and specification matching – info@metav-werkzeuge.com, +49 2822 7131930. Technical Data Article number: 2000867725NW Product name: Tap Drill‑Out Tool M20, solid carbide, TiN‑coated Manufacturer: TECWERK Packaging unit: 1 Facts Teeth: 3 Shank Ø: 18 mm Chip length: 50 mm Core hole Ø: 17.5 mm Materials & features Material: solid carbide (VHM) Coating: TiN Shank type: cylindric Geometry: straight flute, self‑centring, 3 flutes Application: for drilling out broken HSS and HSS‑Co taps FAQ Which tap types can be addressed with this tool? The Tap Drill‑Out Tool M20 (TECWERK, SKU 2000867725NW) is specified for drilling out broken HSS and HSS‑Co thread taps in M20 applications and is engineered for interrupted cutting conditions typical of tap extraction. What clamping is required for safe operation? A secure chuck or collet that accepts an 18 mm cylindric shank is required; the tool’s shank diameter and straight profile support stable clamping to maintain concentricity during extraction. Is the tool self‑centring and how does that help? Yes — the tool features a self‑centring design that assists in aligning with the damaged thread, reducing the risk of wandering and improving the likelihood of a clean extraction on the first attempt. What role does the TiN coating play in performance? The TiN coating increases surface hardness and wear resistance, which helps the TECWERK solid‑carbide tool maintain cutting edge integrity longer under the abrasive conditions of tap removal. What preparatory measures are recommended before use? Ensure correct clamping of the 18 mm shank and verify the pilot or core condition (core hole Ø 17.5 mm where applicable) to reduce radial loads; follow standard safety procedures for interrupted cutting operations. Manufacturer / Responsible: NORDWEST Handel AG, Robert‑Schuman‑Straße 17, 44263 Dortmund

Efficient removal of broken taps is delivered by combining solid carbide construction with a TiN coating and a self‑centring design for reliable chip control; order directly via Metav Werkzeuge or consult the technical team for application advice. Thread extraction drill M5, solid carbide, TiN, Z=3 — TECWERK solid carbide tap‑removal drill, TiN‑coated The Thread extraction drill M5, solid carbide, TiN, Z=3 is a purpose‑built drilling tool for removing broken HSS and HSS‑Co taps, featuring a cylindrical shank and straight flutes for secure seating and controlled chip evacuation. Solid carbide construction TiN‑coated for longer life Self‑centring, straight flutes For drilling out broken HSS taps Precise removal of broken taps with minimal rework The extractor is engineered to remove fractured taps cleanly from threaded holes, reducing rework and scrap. Its self‑centring geometry ensures that the tool locates the broken tap reliably, while the straight flutes guide chips away from the hole. The tool’s core hole Ø 4.2 mm and 3 flutes provide stable cutting engagement, so alignment errors are minimised and subsequent thread repair or retapping becomes straightforward. This focus on repeatable accuracy supports a smooth production flow and predictable results. Long service life through material and coating selection Constructed from solid carbide (VHM) and finished with a TiN coating, the tool resists abrasion and heat during interrupted cuts. The combination of carbide substrate and surface coating reduces flank wear and extends tool life compared with uncoated alternatives. With a chip length of 15 mm and robust cutting geometry, the drill withstands the stresses of extracting brittle HSS and HSS‑Co taps while maintaining dimensional stability over multiple cycles, enhancing overall process economy. Practical handling and speed recommendations for reliable results The extractor has a shank Ø 6 mm, suitable for standard chucks and collets that accept this diameter, and is supplied as a straight‑shank solid tool for easy clamping. Recommended operating speeds are 1,500–3,500 rpm, with a commonly used reference speed of 1,800 rpm depending on machine rigidity and clamping. The design facilitates safe chip evacuation and reduces clogging during operation, so users achieve consistent extraction without excessive force or risk to the workpiece. Contact Metav Werkzeuge today to confirm suitability for specific tap sizes or materials and to secure technical procurement assistance from the specialists in Emmerich — info@metav-werkzeuge.com | +49 2822 7131930 Technical data Article number: 2000867717NW Product name: Thread extraction drill M5, solid carbide, TiN, Z=3 Brand: TECWERK Packaging unit: 1 Key measurements Shank Ø: 6 mm Chip length: 15 mm Core hole Ø: 4.2 mm Number of flutes: 3 Recommended speed: 1,500–3,500 rpm Typical operating speed: 1,800 rpm Features and materials Solid carbide (VHM) TiN‑coated Cylindrical shank Self‑centring Straight‑fluted geometry For drilling out broken HSS and HSS‑Co taps FAQ How does the extractor remove broken taps? The threaded fragment is drilled out using the Thread extraction drill M5, solid carbide, TiN, Z=3, whose self‑centring and straight‑flute design centres on the broken tap and evacuates chips to allow safe extraction. Which tap types is this tool intended for? This extractor is designed specifically for fractured HSS and HSS‑Co taps and performs the mechanical removal task without the need for special consumables. What speeds should be used for safe operation? Operate within 1,500–3,500 rpm as a guideline; 1,800 rpm is a typical reference point depending on machine rigidity and clamping quality when using the TECWERK extractor. Will the shank fit standard chucks? The tool has a 6 mm shank, suitable for standard chucks and collet systems that accept this diameter, allowing secure clamping during the extraction process. What are the main construction and coating benefits? Made from solid carbide (VHM) and TiN‑coated, the drill offers higher wear resistance and thermal stability, which extends tool life during the demanding task of removing broken taps. TECWERK: Manufacturer/Responsible: NORDWEST Handel AG, Robert‑Schuman‑Straße 17, 44263 Dortmund

Fast, precise removal of broken taps is achieved through a combination of solid‑carbide construction, a TiN coating and a self‑centring three‑flute geometry, reducing downtime and minimising rework. The tool’s compact cutting length and Ø 6 mm shank ensure safe clamping and reliable engagement. Order this thread removal drill directly via Metav Werkzeuge or consult our specialists for application advice. Thread removal drill M6 — VHM TiN, 3‑flute (TECWERK) The Thread removal drill M6 VHM TiN Z.3 is a solid‑carbide extractor designed for drilling out broken HSS and HSS‑Co taps in workshop and production settings. Solid carbide (VHM), TiN coated Self‑centring 3‑flute geometry Cylindrical shank Ø 6 mm For removing broken HSS/HSS‑Co taps Minimise downtime with rapid, controlled extraction The three‑flute, self‑centring geometry provides stable engagement and precise guidance into the fractured tool, enabling controlled drilling with minimal radial run‑out. At 1500–3500 rpm (typical 1700 rpm) the tool achieves efficient material removal while limiting heat build‑up; this balance reduces the risk of further workpiece damage and shortens repair intervals. The compact 15 mm cutting length concentrates cutting action where it’s needed, so extraction cycles remain short and predictable. Durable solid‑carbide construction for consistent performance Made from solid carbide, the extractor combines high stiffness with excellent wear resistance for repeated use in industrial environments. The TiN coating lowers friction at the cutting interface and improves surface hardness, which prolongs tool life and maintains cutting geometry under load. Designed specifically for fractured taps, the tool reliably penetrates broken HSS and HSS‑Co taps, reducing the frequency of replacements and supporting steady production output. Secure clamping and straightforward workshop integration A cylindrical shank Ø 6 mm ensures secure holding in standard drill chucks or toolholders, while the straight flute form supports predictable chip formation and evacuation from the bore. The specified core hole Ø 5 mm and geometrical design simplify pre‑drilling steps and alignment. For workshop integration, the tool’s dimensions and operating speed range make it suitable for handheld drills and bench equipment alike, permitting versatile use across maintenance and production tasks. For further application guidance, technical specialists at Metav Werkzeuge are available. Choose TECWERK’s solid‑carbide thread removal drill for fast, reliable extraction — order via Metav Werkzeuge or contact our specialists at info@metav-werkzeuge.com / +49 2822 7131930 for tailored advice Technical data Article number: 2000867718NW Product name: Thread removal drill M6 VHM TiN Z.3 Packaging unit: 1 Facts Flutes: 3 Cutting length: 15 mm Shank diameter: Ø 6 mm Core hole diameter: Ø 5 mm Recommended speed: 1500–3500 rpm (typ. 1700 rpm) Special features Solid carbide (VHM) TiN coating Cylindrical shank Self‑centring geometry Straight flutes For removing broken HSS and HSS‑Co taps Suitable for workshop and production use FAQ What materials is this extractor designed for? The Thread removal drill M6 VHM TiN Z.3 is designed specifically to drill out broken HSS and HSS‑Co taps. Which speeds are recommended for safe operation? Recommended operating range is 1500–3500 rpm, with a typical working speed of around 1700 rpm for controlled extraction. How does the TiN coating benefit the tool? The TiN coating reduces friction and improves surface hardness, which extends the service life and maintains cutting performance under load. What holding methods are suitable for this extractor? The Ø 6 mm cylindrical shank is compatible with standard drill chucks and common toolholders for stable clamping during extraction. Manufacturer / Responsible: NORDWEST Handel AG, Robert‑Schuman‑Straße 17, 44263 Dortmund

Take advantage of the combination of solid carbide construction and TiN coating for a robust, wear‑resistant solution to remove broken taps; the self‑centring, straight‑flute geometry ensures fast rework and reliable repeatability. Order the tool directly via Metav Werkzeuge or ask the consultants for application guidance. Tap extraction drill M8 – VHM solid‑carbide, TiN‑coated, 3‑flute (TECWERK) The Tap extraction drill M8 is a solid‑carbide, TiN‑coated tool designed for safe removal of broken HSS and HSS‑Co tap drills in maintenance and toolroom environments Solid carbide (VHM) construction TiN coating for enhanced wear resistance Self‑centring, straight flutes 3‑flute design, 20 mm chip length Precision and efficiency for repair work The tool combines solid carbide rigidity with a TiN coating to deliver high cutting stability and reduced flank wear when reworking seized or broken taps. The hardened cutting material maintains concentricity under load, which reduces the risk of further damage to the workpiece. As a result, repair cycles are shorter and the need for subsequent corrective machining is minimised, supporting faster turnaround in maintenance or production environments. Design that reduces risk and speeds operation A self‑centring geometry with straight flutes ensures reliable entry into the broken tap and consistent chip evacuation over the 20 mm chip length. The 3‑flute arrangement balances cutting forces and aids stable guidance through the broken tool, while the 8 mm shank suits common drill holders and chucks. The tool’s 6.8 mm core diameter provides a controlled material removal profile to expose and extract fractured tap fragments with minimal collateral impact. Practical workshop applications and handling tips Suitable for use in toolrooms, maintenance shops and industrial workshops, the device excels in reworking broken HSS and HSS‑Co tap drills where precision and repeatability matter. Operate with appropriate clamping and coolant practices to extend tool life; the TiN coating improves resistance to abrasion and reduces built‑up edge formation. For hand‑held machines or drill presses, ensure secure holding of the 8 mm shank and controlled feed to avoid deflection during extraction. For reliable tap removal with TECWERK solid‑carbide performance, contact Metav Werkzeuge in Emmerich for ordering or technical consultation via info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: 2000867719NW Manufacturer: TECWERK Packing unit: 1 Facts Chip length: 20 mm Number of teeth: 3 Shank diameter: 8 mm Core diameter: 6.8 mm Special features VHM (solid carbide) cutting material TiN‑coated surface Cylindrical shank Self‑centring design Straight‑flute geometry For drilling out broken HSS and HSS‑Co tap drills FAQ What materials can this tool rework? The Tap extraction drill M8 is intended for removing broken HSS and HSS‑Co tap drills; its solid‑carbide construction provides the rigidity required for such repair tasks. Which holder is suitable for the shank? An 8 mm drill chuck or suitable collet is recommended to secure the 8 mm shank of the TECWERK tap extraction drill for stable operation. How does the TiN coating help in extraction work? The TiN coating on the tool reduces abrasive wear and helps prevent built‑up edge, which improves service life during repeated tap removal operations with the TECWERK tool. Manufacturer/Responsible: NORDWEST Handel AG, Robert‑Schuman‑Straße 17, 44263 Dortmund

Take advantage of a tool that combines solid carbide construction, a TiN coating and a self‑centring design to speed up tap recovery and reduce scrap; order directly via Metav Werkzeuge or contact our advisors for matching accessories and delivery options. Thread extraction drill M16 – solid carbide, TiN‑coated (TECWERK) The Thread extraction drill M16 is a self‑centring, three‑flute solid carbide tool designed for removing broken HSS and HSS‑Co taps in industrial and workshop environments. Solid carbide (VHM) for high stiffness TiN coating for improved wear resistance Self‑centring three‑flute geometry Cylindrical 14 mm shank for secure clamping Faster recovery of broken taps with less rework This extraction drill is engineered for efficient removal of fractured taps, converting downtime into controlled repair work. The three‑flute geometry and straight flutes provide predictable chip evacuation and stable cutting, which means fewer secondary operations and less scrap. For workshop managers and maintenance teams, the practical outcome is a shorter repair cycle and a lower overall throughput loss when dealing with broken HSS or HSS‑Co taps. Durable design that stands up to repetitive use Made from solid carbide (VHM) and finished with a TiN coating, the tool delivers high rigidity and enhanced surface hardness. TiN (titanium nitride) reduces friction and increases resistance to abrasive wear, extending tool life under repetitive conditions. The combination of material and coating translates into reliable performance across multiple recovery tasks and reduces the frequency of tool replacement in demanding production settings. Precision clamping and stable alignment A cylindrical 14 mm shank ensures secure holding in standard collets and chucks, while the self‑centring design aids alignment with the broken tap’s axis. The result is improved concentricity during the extraction process and a reduced risk of collateral damage to the parent thread. This mechanical certainty is particularly valuable when working on high‑value components where preserving thread integrity is essential. Clear technical layout for integration into workshop workflows Key dimensions such as a 40 mm flute length and a core hole diameter of 14 mm make planning straightforward for machinists and maintenance planners. The tool’s straightforward specification allows rapid selection of appropriate holders and depth stops, supporting safe and repeatable operation. By relying on a tool specified for the task, teams gain operational confidence and better predictability in repair outcomes. Choose TECWERK quality for efficient tap recovery and contact Metav Werkzeuge for personalised advice and reliable supply from Emmerich: info@metav-werkzeuge.com or +49 2822 7131930 Technical data Article number: 2000867723NW Name: Thread extraction drill M16 VHM TiN Z.3 TECWERK Manufacturer: TECWERK Packaging unit: 1 Facts Flute length: 40 mm Number of teeth: 3 Shank diameter: 14 mm Core hole diameter: 14 mm Special features Solid carbide (VHM) TiN coating Cylindrical shank Self‑centring design Straight flutes For removing broken HSS and HSS‑Co taps FAQ How does the tool remove broken taps without damaging the thread? The Thread extraction drill M16 uses a self‑centring, three‑flute geometry to align with the fractured tap and remove material in a controlled way, minimising risk to the surrounding thread. What materials is this extraction drill suitable for? This TECWERK tool is specified for extracting broken HSS and HSS‑Co taps and is produced from solid carbide with a TiN coating to withstand the cutting stresses involved. Which shank size is required for clamping? A 14 mm cylindrical shank is provided, suitable for standard collets and chucks that accept that diameter, ensuring secure clamping during extraction. What are the key dimensions to consider when planning the operation? Important values include a flute length of 40 mm and a core hole diameter of 14 mm; these guide depth setting and holder choice for a safe operation. Is the tool suitable for repetitive industrial use? Yes, the combination of solid carbide construction and TiN coating gives the tool durability for repeated extraction tasks in workshop and light industrial settings. Manufacturer/Responsible: NORDWEST Handel AG, Robert‑Schuman‑Straße 17, 44263 Dortmund