VNMG160404-MP3 WPP20G WPP20G Wendeplatten - Walter Tools
Take advantage of the combination of Tiger‑tec Gold coating and the MP3 chipbreaker for stable chip formation and extended tool life; the rhombic 35° geometry with a 0.4 mm corner radius provides predictable edge engagement for steel machining. Order the insert directly via Metav Werkzeuge or consult their advisors for application support. VNMG160404-MP3 WPP20G Turning Insert – for Steel (Walter Tools) The VNMG160404-MP3 WPP20G is a rhombic 35° indexable turning insert with an MP3 chipbreaker and Tiger‑tec Gold coating, engineered for reliable machining of steel (ISO group P). Tiger‑tec Gold coating for wear resistance Optimised for machining steel (ISO group P) MP3 chipbreaker for reliable chip control Rhombic 35° shape with 0.4 mm corner radius Consistent wear resistance for productive turning The combination of the WPP20G cutting grade and Tiger‑tec Gold coating yields a wear‑resistant, coated carbide structure that supports long tool life under typical steel turning conditions. The coated substrate was developed to handle the heat and chip formation characteristic of ISO P materials, which results in fewer tool changes and reduced downtime. When fitted in a suitable holder, the insert enables higher cutting parameters while maintaining dimensional consistency; the outcome is increased throughput and lower unit costs per component. The statement of suitability for steel is derived from the material designation P and the grade composition. Reliable chip control and secure edge stability The MP3 chipbreaker, paired with the rhombic 35° geometry and a 0.4 mm corner radius, delivers predictable chip shaping and controlled evacuation during turning operations. A 0° negative rake influences cutting forces and edge engagement, making the insert a good option for medium to finishing cuts where surface quality and repeatability are priorities. The rhombic form ensures stable seat contact in standard toolholders and supports straightforward indexing; the controlled edge radius helps preserve surface finish while providing a balance between edge strength and sharpness. Process security and versatility in production Tolerance class M and the measured plate dimensions establish this component as a consistent, production‑ready solution for shops machining a broad range of steels. The insert’s design promotes process security through reproducible tool performance and stable chip formation, which is particularly relevant in serial production and mixed‑batch environments. Compatibility with common clamping systems and straightforward insert handling reduce setup complexity, while the grade’s universal characteristics allow its use across a variety of steel types without frequent grade swaps. The result is dependable repeatability and efficient integration into existing machining cycles. For application advice or to order Walter Tools Tiger‑tec Gold inserts, contact Metav Werkzeuge for tailored recommendations and availability at info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: VNMG160404-MP3-WPP20G-WALTER Product designation: VNMG160404-MP3 WPP20G Brand: Walter Tools Facts Plate size: 16 mm Plate thickness: 4 mm Corner radius: 0.4 mm Shape: Rhombic 35° Rake angle: 0° (negative) Special features Grade: WPP20G Series: Tiger‑tec Gold Chipbreaker: MP3 Material application: Steel (ISO group P) Tolerance class: M FAQ What materials is this insert intended for? The VNMG160404-MP3 WPP20G insert is specified for machining steel (ISO group P) and is optimised for the heat and chip characteristics typical of those materials. How does the MP3 chipbreaker affect productivity? The MP3 chipbreaker shapes and evacuates chips reliably, which supports higher cutting parameters and reduces interruptions caused by poor chip control when using the WPP20G grade. What does the 0° negative rake mean in practice? A 0° negative rake provides a sturdy cutting edge that improves edge stability under load, offering a balance between tool life and surface quality for the intended turning applications. Is this insert compatible with standard toolholders? The rhombic 35° form and VNMG designation correspond to common turning insert standards, enabling use in compatible indexable holders designed for this geometry. Die Walter AG (brand appearance: Walter Tools) is a globally recognised manufacturer of precision tools for metalworking and is part of the Sandvik Group. Protected trademarks and trade names remain the property of their respective owners. Brand names and registered trademarks are used for explanation only; there is no affiliation between our company and the mentioned brands. The item offered is original and brand new. Manufacturer/Responsible: Kennametal; 600 Grant Street, Suite 5100, Pittsburgh, PA 15219, USA; www.kennametal.com; ftmill.service@kennametal.com Manufacturer/Responsible: ISCAR Ltd.; Industrial Zone, P.O.Box 11; 24959 Tefen; Israel; www.iscar.so.il; info@iscar.co.il Manufacturer/Responsible: AB Sandvik Coromant, Mossvägen 10, 811 34 Sandviken, Sweden, support.coromant@sandvik.com Manufacturer/Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
VNMG160404-MP5 WPP10G WPP10G Wendeplatten - Walter Tools
Benefit from a combination of durable coating and stable chip control: the Tiger‑tec Gold grade WPP10G delivers extended tool life and consistent performance when machining Stahl, while the MP5 chipbreaker ensures reliable chip formation in a wide range of turning operations. Order or request application advice via Metav Werkzeuge for seamless integration into the production line. VNMG160404-MP5 WPP10G turning insert, Tiger‑tec Gold for Stahl — Walter Tools The VNMG160404-MP5 WPP10G is a rhombic 35° indexable turning insert designed for general-purpose and medium-duty turning of Stahl, featuring the Tiger‑tec Gold coating and the MP5 chipbreaker for dependable chip control. Tiger·tec Gold coating for enhanced wear resistance MP5 chipbreaker for stable chip formation Rhombic 35° geometry with 0.4 mm corner radius 0° negative rake for robust cutting performance High productivity thanks to a wear‑resistant coating The Tiger‑tec Gold coating combined with the WPP10G grade provides a measurable improvement in tool life and process stability when machining Stahl (P). The coated carbide substrate is engineered to withstand the typical temperatures and chip behaviour of steel turning, which reduces the frequency of insert changes and supports uninterrupted production cycles. This configuration is particularly appropriate where long tool life and low variance in performance are priorities. Consistent chip control and surface integrity The MP5 chipbreaker was developed to produce predictable chips across a variety of cutting parameters, reducing the risk of entanglement and improving surface finish. The rhombic 35° cutting geometry combined with a 0.4 mm corner radius helps to distribute cutting forces evenly, which benefits both tool life and part quality. For operations that demand reproducible chip evacuation and consistent results, this geometry-chipbreaker pairing increases reliability on the shop floor. Robust geometry for demanding turning conditions A 0° (negative) rake angle and the specified plate thickness align the insert with tougher and interrupted cuts, giving mechanical strength at the cutting edge and enhanced resistance to edge chipping. The tolerance class M ensures dimensional consistency for indexable insert seating and repeatable tool offsets. These design choices favour operators who require predictable, repeatable performance in medium-duty to heavy-duty turning tasks. Application range and practical assignment The grade is optimised for Stahl (P) applications per ISO 513 and covers a spectrum from wear-resistant to tougher steels (grade indications 10, 20, 30/35). The combination of the Tiger‑tec Gold technology and the MP5 chipbreaker makes this insert a balanced choice for mixed production runs that include a variety of steel grades. For grade selection and matching to cutting conditions, the product line from Walter Tools offers clear assignment logic to aid process planning. For tailored grade selection, delivery options and application advice for Walter Tools Tiger‑tec Gold turning inserts, please contact Metav Werkzeuge — info@metav-werkzeuge.com, +49 2822 7131930 Technical data SKU: VNMG160404-MP5-WPP10G-WALTER Article designation: VNMG160404-MP5 WPP10G Brand: Walter Tools Series: Tiger-tec Gold Grade: WPP10G Facts Insert size: 16 Thickness: 04 Corner radius: 0.4 mm Free angle: 0° (negative) Tolerance class: M Special features Chipbreaker: MP5 Geometry: Rhombus 35° Execution: G Material application: Stahl (P) Product type: Drehwendeschneidplatte (indexable turning insert) FAQ What materials is this insert suitable for? The VNMG160404-MP5 WPP10G is designed for Stahl (P) applications according to ISO 513 and is intended for a range of steel types from wear‑resistant to tougher steels. Which coating and grade are used on the insert? The insert uses the Tiger‑tec Gold coating and the Walter Tools grade WPP10G, a coated carbide formulation optimised for steel turning. What chip control and geometry does the insert provide? This insert features the MP5 chipbreaker, a rhombic 35° shape and a 0.4 mm corner radius to promote reliable chip formation and consistent surface finish. Is the insert suitable for interrupted cuts or heavy cuts? The 0° (negative) rake angle and robust geometry make the insert suitable for more demanding conditions, offering improved edge strength for interrupted or heavier feeds. Which tolerance and execution are specified for the insert? The insert is supplied in tolerance class M with execution code G, providing consistent dimensions for accurate tool mounting. Hersteller: Walter Tools; Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Trademarks and trade names are the property of their respective owners. Brand names and protected product designations are mentioned for explanatory purposes only. There is no affiliation between our company and the mentioned brands. The offered item is an original, brand‑new product supplied by the manufacturer (Walter Tools).
VNMG160404-MP5 WPP20G WPP20G Wendeplatten - Walter Tools
Take advantage of the combination of Tiger·tec Gold coating, a proven WPP20G carbide grade and the MP5 chipbreaker for consistent steel machining with reliable chip control; this ensures productive turning and predictable tool life. Order the VNMG160404-MP5 WPP20G directly via Metav Werkzeuge or ask our consultants if needed. VNMG160404-MP5 WPP20G turning insert — Tiger·tec Gold coated, Rhombus 35°, for steel machining (Walter Tools) A VNMG160404-MP5 WPP20G turning insert engineered for steel applications, offering a robust MP5 chipbreaker and Tiger·tec Gold coating for stable cutting and consistent surface quality. Tiger·tec Gold coated grade WPP20G MP5 chipbreaker for controlled chips Rhombus 35° geometry for versatile turning High process reliability through optimised grade and coating The combination of the WPP20G carbide grade and Tiger·tec Gold coating delivers robust wear resistance together with predictable performance when machining steel. The coated hardmetal formulation balances toughness and hardness to resist flank wear while maintaining a consistent cutting edge. This results in fewer unscheduled insert changes and improved machine uptime, which supports higher overall productivity in batch and continuous turning operations. Controlled chips and dimensional consistency for shop-floor efficiency The dedicated MP5 chipbreaker geometry is designed to generate short, manageable chips during common steel turning tasks, reducing the risk of entanglement and easing chip evacuation. The Rhombus 35° insert form and 0.4 mm corner radius provide a stable cutting edge for finish and medium cuts, enabling repeatable diameters and good surface integrity. As a consequence, setup time is reduced and downstream operations benefit from parts that require less rework. Practical application and integration into existing toolholders With a negative 0° free angle and a standard VNMG footprint, the insert fits conventional turning toolholders used across metalworking shops. The insert’s designation and dimensions facilitate quick selection in tooling systems, and the grade’s focus on steel machining means cutting parameters are forgiving during job changes. For new applications or unusual alloy grades, consult cutting data to match speeds and feeds to the material class for optimal life and surface finish. Contact Metav Werkzeuge for tailored cutting-data recommendations, toolholder compatibility checks and application support for Walter Tools Tiger·tec Gold VNMG160404-MP5 WPP20G Technical Data Article number: VNMG160404-MP5-WPP20G-WALTER SKU: VNMG160404-MP5-WPP20G-WALTER Product name: VNMG160404-MP5 WPP20G Series: Tiger·tec Gold Grade: WPP20G Facts Insert size: 16 mm Thickness: 04 (4 mm) Corner radius: 0.4 mm Geometry: Rhombus 35° Free angle: 0° (negative) Tolerance class: M Special features Chipbreaker: MP5 Material suitability: Steel (P) Cutting-edge type: G Coated carbide (Tiger·tec Gold) Shape designation: VNMG160404-MP5 FAQ What materials is this insert suited for? The VNMG160404-MP5 WPP20G is designed primarily for machining steel (material group P); the Tiger·tec Gold grade optimises wear resistance and edge stability for typical steel turning operations. How does the MP5 chipbreaker affect machining? The MP5 chipbreaker produces short, controllable chips when turning steel, improving chip flow and reducing the risk of chip-related interruptions in the workpiece or toolpath. Can this insert be used in standard VNMG toolholders? Yes, the insert follows the VNMG form and fits conventional VNMG toolholders; the negative 0° free angle should be considered when selecting holder geometry and entering cutting data. What benefits does the Tiger·tec Gold coating provide? The Tiger·tec Gold coating on the WPP20G grade enhances wear resistance and thermal stability, which contributes to longer edge life and consistent surface quality in steel turning. Is the 0.4 mm corner radius suitable for finishing? A 0.4 mm corner radius offers a compromise between edge strength and surface finish, making it suitable for light to medium finishing passes while maintaining robustness against minor interruptions. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Geschützte Markenzeichen und Warenbezeichnungen liegen im Recht ihrer jeweiligen Eigentümer. Markennamen und geschützte Warenbezeichnungen werden ausschließlich zu Erklärungszwecken genannt. Es besteht keinerlei Verbindung zwischen unserem Unternehmen und den genannten Marken. Es handelt sich bei dem angebotenen Artikel um originale fabrikneue Waren des Herstellers.
VNMG160404-MP5 WPP30G Wendeplatten - Walter Tools
Take advantage of a high-performance combination of durability and consistent chip control: the coated carbide grade delivers extended tool life while the MP5 chipbreaker and rhombic geometry ensure reliable material removal in Stahl operations. Order directly via Metav Werkzeuge or consult the technical team for application-specific recommendations. VNMG160404-MP5 WPP30G indexable turning insert — rhombic 35°, Tiger·tec Gold (Walter Tools) The VNMG160404-MP5 WPP30G is a rhombic 35° indexable turning insert engineered for medium-to-high performance turning in Stahl, featuring a Tiger·tec Gold coated carbide grade and an MP5 chipbreaker for stable chip formation. Tiger·tec Gold coating for long tool life Optimised MP5 chipbreaker for Stahl Rhombic 35° form, 0.4 mm corner radius Negative 0° rake for robust cutting performance Consistent performance through advanced grade and coating The Tiger·tec Gold coating combined with the WPP30G carbide formulation gives a balance between wear resistance and toughness. This results in a stable cutting edge under the thermal and mechanical loads typical when machining Stahl. The coated hardmetal structure reduces flank wear and extends the burndown interval, which supports fewer index changes and more uptime on the lathe. For workshop managers and production planners, this translates into predictable tool life and improved productivity per toolholder. Reliable chip control and surface quality for productive turning The MP5 chipbreaker is designed to direct and segment chips consistently in turning of Stahl, reducing the risk of long, entangling swarf and supporting safe, repeatable operations. The rhombic 35° geometry with a 0.4 mm corner radius helps to achieve a controlled cutting engagement and improved surface finish when compared with more aggressive geometries. For operators with varying material batches, this insert provides a dependable compromise between robustness and surface quality, making it suitable for general turning applications and semi-finish passes. Robust form and geometry for versatile setup compatibility With a negative 0° rake and the VNMG form factor, the insert offers a sturdy cutting edge that resists chipping under interrupted cuts or heavier depth of cut. The standardised VNMG shape supports wide toolholder availability and straightforward index changes, simplifying tool management. The insert’s dimensions and tolerance class M ensure interchangeability in common turning systems, which helps to minimise setup time and supports a smooth production flow across multiple machines. For application matching, availability checks or tailored cutting data for the Walter Tools VNMG160404-MP5 WPP30G insert, contact Metav Werkzeuge for expert advice and ordering assistance at info@metav-werkzeuge.com or +49 2822 7131930 Technical data Article number: VNMG160404-MP5-WPP30G-WALTER SKU: VNMG160404-MP5-WPP30G-WALTER Product type: Drehwendeschneidplatte (indexable turning insert) Series: Tiger·tec Gold Grade: WPP30G Facts Insert shape: Rhombus 35° Corner radius: 0.4 mm Free rake: 0° (negative) Insert size: 16 Thickness: 04 Tolerance class: M Special features Coating: Tiger·tec Gold (coated hardmetal) Chipbreaker: MP5, optimised for Stahl Material application: Stahl Designation without grade: VNMG160404-MP5 ISO designation: VNMG160404-MP5 WPP30G Manufacturer: Walter Tools FAQ What material groups is this insert suited for? The VNMG160404-MP5 WPP30G is specified for machining Stahl; the WPP30G grade and MP5 chipbreaker are tuned for the thermal and chip-formation characteristics of Stahl. How does the Tiger·tec Gold coating benefit production? Tiger·tec Gold coating on the WPP30G grade increases wear resistance and edge stability, meaning longer intervals between indexing and more consistent component quality when using the VNMG insert. Is the MP5 chipbreaker suitable for semi-finish as well as roughing? Yes, the MP5 geometry offers controlled chip segmentation that performs well across semi-finish and certain roughing conditions in Stahl turning, improving process reliability. Can the VNMG160404-MP5 be used in interrupted cuts? The negative 0° rake and robust edge integrity of this insert provide good resistance to chipping under interrupted cutting conditions. Which toolholders are compatible with the VNMG shape? The VNMG form is a standard indexable insert shape; compatible toolholders that accept rhombic 35° VNMG inserts are suitable for this grade and geometry. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen The Walter AG (brand presentation: Walter Tools) with headquarters in Tübingen is one of the world’s leading manufacturers of precision tools for metalworking and is part of the Swedish Sandvik group. Protected trademarks and trade names are the property of their respective owners. Brand names are mentioned only for explanation purposes. There is no affiliation between our company and the named brands. The offered item is an original, factory-new product from the manufacturer.
VNMG160404-MS3 WSM01 WSM01 Wendeplatten - Walter Tools
Combine cost-effective production with stable chip formation and high process security for reliable turning of demanding alloys; order the VNMG160404‑MS3 WSM01 insert directly via Metav Werkzeuge or consult our technical advisors for application support. VNMG160404‑MS3 WSM01 turning insert — Tiger‑tec Silver, for stainless steels (Walter Tools) The VNMG160404‑MS3 WSM01 is a rhombic 35° turning insert designed for stable material removal in rostfreier Stahl and heat‑resistant superalloys, featuring a MS3 chipbreaker and a negative 0° relief angle. Tiger‑tec Silver series coating for longevity WSM01 grade for rostfreier Stahl and superalloys Rhombic 35° form with 0.4 mm corner radius MS3 chipbreaker for controlled chip formation High process security for demanding materials The Tiger‑tec Silver series and the WSM01 grade combine a wear‑resistant, coated carbide substrate with a geometry tailored to the challenges of rostfreier Stahl and heat‑resistant alloys. This results in stable cutting edges and reduced risk of built‑up edge, which is especially important when machining materials that generate heat and adhere to the tool. The rhombic 35° shape and 0° negative relief promote predictable engagement and repeatable results, supporting consistent surface finish and dimensional stability for serial production. Reliable chip control that keeps cycles running The MS3 chipbreaker is engineered to promote reliable chip formation under the high temperatures and adhesive tendencies of rostfreier Stahl and superalloys. Controlled chips reduce the need for manual intervention and protect the workpiece and toolholder from damage, increasing uptime and throughput. With a 0.4 mm corner radius the insert balances edge strength and finishing capability, enabling longer tool life without compromising part quality. Designed for productivity and easy process integration As a coated indexable insert in the Tiger‑tec Silver family, this component supports higher cutting parameters and longer tool life compared with uncoated grades, contributing to improved cost efficiency per part. The insert’s VNMG style provides universal clamping compatibility across common toolholders, simplifying tool logistics on the shop floor. Clear material suitability and the robust design help reduce set‑up time and enable confident process planning for both prototype and series turning operations. For application advice on Walter Tools Tiger‑tec Silver inserts or to secure the VNMG160404‑MS3 WSM01 for an upcoming production run, contact Metav Werkzeuge’s technical team at info@metav-werkzeuge.com or by phone on +49 2822 7131930 — Metav Werkzeuge supports rapid delivery and practical machining guidance. Technical Data Article number: VNMG160404‑MS3‑WSM01‑WALTER SKU: VNMG160404‑MS3‑WSM01‑WALTER Series: Tiger‑tec Silver Grade: WSM01 Facts Corner radius: 0.4 mm Inscribed circle: 16 mm Thickness: 04 Relief angle: 0° (negative) Special features Chipbreaker: MS3 Insert shape: Rhombic 35° Coating: Tiger‑tec Silver (coated carbide) Suitable for: rostfreier Stahl; heat‑resistant superalloys and titanium Application focus: Stable chip formation and high process security Manufacturer brand: Walter Tools FAQ What materials is this insert best suited for? The VNMG160404‑MS3 WSM01 insert is optimised for rostfreier Stahl and heat‑resistant superalloys, where the WSM01 grade and Tiger‑tec Silver coating deliver stable chip control and edge stability. How does the MS3 chipbreaker improve machining performance? The MS3 chipbreaker on this Walter Tools insert promotes predictable chip curl and manageable chip segments, reducing the risk of entanglement and supporting continuous production in demanding materials. What does the 0° negative relief angle mean for cutting? A 0° (negative) relief increases edge strength and resistance to chipping under heavy loads; this geometry on the VNMG‑style insert enhances durability when machining sticky or high‑temperature alloys. Can this insert be used in standard VNMG toolholders? Yes, the insert’s VNMG form factor and clamping geometry ensure compatibility with common VNMG toolholders, facilitating rapid integration into existing turning setups. What corner radius should be chosen for finishing versus roughing? The 0.4 mm corner radius supplied here offers a balance between edge strength and surface finish; for heavier roughing a larger radius could be preferred, while a smaller radius benefits fine finishing—consult Metav Werkzeuge for tailored recommendations. Manufacturer: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen, Germany The Walter AG (brand appearance: Walter Tools) with headquarters in Tübingen is among the world’s leading manufacturers of precision tooling for metalworking and is part of the Sandvik group. Protected trade names and trademarks remain the property of their respective owners. Brand names and registered trademarks are used solely for descriptive and explanatory purposes and indicate no affiliation between our company and the trademark owners. The offered item is an original, factory‑new product from the manufacturer.
VNMG160404-MS3 WSM10S WSM10S Wendeplatten - Walter Tools
Take advantage of the combination of high edge stability, effective chip control and the Tiger‑tec Silver coating for a reliable production process; order the insert directly via Metav Werkzeuge or consult our specialists for machining parameters. VNMG160404-MS3 WSM10S — Indexable turning insert, Tiger‑tec Silver coating (rhombic 35°, 0° negative) — Walter Tools VNMG160404-MS3 WSM10S is a rhombic indexable turning insert designed for demanding turning operations on rostfreier Stahl and heat‑resistant alloys, offering a stable cutting edge and dedicated chip control. Tiger‑tec Silver coating for heat resistance Stable cutting edge for difficult materials Rhombus 35° geometry with 0.4 mm nose radius MS3 chipbreaker for consistent chip formation Increased process reliability for tough materials The combination of the WSM10S grade and the Tiger‑tec Silver coating delivers improved thermal resistance and wear behaviour when machining rostfreier Stahl and nickel‑base alloys. The grade is a coated carbide designed to support secure chip formation and a durable cutting edge under elevated temperatures and adhesion tendencies typical of these materials. This results in fewer interruptions for tool changes and more predictable batch completion times. Consistent surface quality and chip management The MS3 chipbreaker paired with the rhombic 35° geometry ensures controlled chip flow and reduced risk of built‑up edge, which is critical when turning materials that produce long or stringy chips. The 0° (negative) free angle increases cutting edge strength, while the 0.4 mm nose radius balances surface finish and edge robustness. These features translate into stable dimensional results and a lower scrap rate in series production. Productivity gains and economic benefit Using a grade optimised for M and S workpiece groups shortens process development and extends tool life, supporting faster cycles and reduced tooling costs per component. The insert’s architecture aims to maintain a stable cutting edge over longer tool life, which reduces downtime and increases the utilisation of turning centres—an appreciable advantage in both batch and continuous production environments. Practical handling and application guidance The insert is intended for conventional and semi‑finishing turning of rostfreier Stahl and heat‑resistant superalloys; appropriate cutting speeds, feeds and coolant strategies depend on the specific material and machine rigidity. For setups where thermal load is a concern, the Tiger‑tec Silver coating supports heat management at the cutting edge. For detailed cutting data, Metav Werkzeuge can provide tailored recommendations to match the machining centre and workpiece. For machining rostfreier Stahl and superalloys with high process reliability choose the Walter Tools VNMG160404‑MS3 WSM10S—contact Metav Werkzeuge for specification support at info@metav-werkzeuge.com or by phone at +49 2822 7131930 Technical data Article number: VNMG160404-MS3-WSM10S-WALTER Description: Drehwendeschneidplatte VNMG160404-MS3 WSM10S Walter Tools Manufacturer: Walter Tools Type: Drehwendeschneidplatte / Indexable turning insert Grade: WSM10S Series: Tiger‑tec Silver Facts Insert size: 16 mm Thickness: 0.4 mm Nose radius: 0.4 mm Free angle: 0° (negative) Geometry: Rhombus 35° Tolerance class: M Special features Coating: Tiger‑tec Silver Chipbreaker: MS3 Suitable for: rostfreier Stahl (M) and heat‑resistant superalloys/Titan (S) Material: coated carbide Application: turning FAQ Is this insert suitable for rostfreier Stahl? Yes. The VNMG160404‑MS3 WSM10S is optimised for rostfreier Stahl (ISO group M) and provides thermal stability and reliable chip formation when machining stainless materials. What does the Tiger‑tec Silver coating provide? The Tiger‑tec Silver coating enhances heat resistance and wear performance, helping the insert maintain a stable cutting edge during demanding turning of heat‑sensitive materials. How does the MS3 chipbreaker affect machining? The MS3 chipbreaker produces consistent chip shapes and reduces risk of built‑up edge, improving surface quality and process reliability in continuous machining operations. Can this insert be used for titanium alloys? Yes. The insert’s designation and grade support application in the S group, which includes heat‑resistant superalloys and titanium, where edge strength and thermal resistance are required. What cutting geometry advantages does the rhombic 35° offer? The rhombic 35° form provides a compromise between approach angle and edge strength, aiding stable turning and good access for profile work while maintaining rigidity. Manufacturer/Responsible: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen; Germany Protected trademarks and trade names are the property of their respective owners. Brand names and registered trademarks are mentioned for explanation only and do not imply any affiliation with our company. The offered article is an original, factory‑new product of the manufacturer.
VNMG160404-NFT WS10 G Wendeplatten - Walter Tools
The combination of the WS10 coated grade and the NFT chipbreaker delivers reliable chip control and stable cutting in general turning operations; the 0° (negative) rake) and 0.4 mm corner radius further enhance edge security and profile versatility. Order genuine Walter Tools inserts through Metav Werkzeuge or request application guidance from our consultants. VNMG160404-NFT WS10 turning insert – Rhombic 35°, 0° negative rake | Walter Tools A VNMG160404-NFT WS10 indexable turning insert engineered for general turning where consistent chip formation and process stability are required. WS10 coated carbide grade for wide material scope Chipbreaker NFT for consistent chip control Rhombic 35° geometry for versatile turning 0° negative rake for secure cutting edges Predictable chip control for higher productivity The insert uses the chipbreaker NFT combined with the WS10 coated carbide grade to produce reproducible chip forms and reduced tendency to build up material on the edge. Coated carbides increase wear resistance by adding a thin, hard layer to the substrate; this slows flank and crater wear and extends useful edge life in intermittent and continuous cuts. The result is improved process security and fewer unplanned tool changes, which benefits throughput and reduces downtime in batch production. Geometry designed for flexible turning tasks The Rhombic 35° geometry and 0° (negative) rake) create a stable cutting configuration that suits a broad range of turning operations, from finishing to light roughing when paired with the correct feed and speed. The 0.4 mm corner radius supports adaptable profiles and helps avoid premature chipping on interrupted cuts. For less experienced users: a negative rake increases strength at the cutting edge and is often selected where edge robustness takes priority over aggressive cutting action. Clear selection criteria and application guidance Tolerance class M, inscribed circle 16 mm and the Version G execution indicate consistent dimensions and fitment for standard toolholders. The material information is catalogue-dependent, so workpiece suitability should be checked in the specific product matrix before final selection. For operations involving unfamiliar alloys or special machining conditions, trial cuts and adjusted cutting data are recommended to exploit the insert’s balance of edge security and wear resistance while maintaining surface quality. For application-specific cutting data or to source genuine Walter Tools VNMG160404-NFT WS10 inserts, contact Metav Werkzeuge at info@metav-werkzeuge.com or call +49 2822 7131930 for expert consultation and availability. Technical data Article number: VNMG160404-NFT-WS10-WALTER Designation: VNMG160404-NFT WS10 Type: Drehwendeschneidplatte Manufacturer: Walter Tools Grade: WS10 Facts Inscribed circle: 16 mm Plate thickness: 04 Corner radius: 0.4 mm Rake angle: 0° (negative) Geometry: Rhombic 35° Tolerance class: M Special features Chipbreaker: NFT Coating / material: catalogue-dependent Series: Walter cutting material grade – open series Version: G Application note: Workpiece suitability to be checked in product matrix FAQ What materials is this insert suitable for machining? The VNMG160404-NFT WS10 insert is supplied in the WS10 coated grade; material suitability varies by product matrix, so check the specific catalogue data for compatibility with the intended workpiece. How does the NFT chipbreaker affect machining? The chipbreaker NFT promotes consistent chip formation and evacuation, which improves process security and reduces the risk of chip entanglement during turning. What does a 0° negative rake mean in practice? A 0° (negative) rake) provides a robust cutting edge that resists chipping under interrupted cuts and heavier engagement, favouring tool life and edge stability over aggressive cutting action. Is the insert compatible with standard VNMG toolholders? The insert uses the VNMG designation and an inscribed circle of 16 mm, so it fits standard VNMG toolholders designed for that size; verify holder compatibility before assembly. How should the 0.4 mm corner radius be used? The 0.4 mm corner radius is suitable for a balance of surface finish and edge strength; select appropriate feeds to avoid excessive burr formation while benefiting from improved edge durability. Manufacturer: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen; Germany The Walter AG (brand: Walter Tools) with its headquarters in Tübingen is one of the world’s leading manufacturers of precision tools for metalworking and forms part of the Sandvik Group. Protected trademarks and trade names remain the property of their respective owners. Mark names and protected designations are used solely for explanation. The offered item is an original, brand-new product from the manufacturer.
VNMG160404-NFT WSM20S WSM20S Wendeplatten - Walter Tools
Take advantage of the combination of Tiger·tec Silver wear resistance, a 0° negative rake for robust cutting and precise chip control (NFT) to keep production stable and efficient; order through Metav Werkzeuge or consult our advisors for application-specific recommendations. VNMG160404-NFT WSM20S indexable turning insert — Rhombic 35°, 0.4 mm corner radius, Walter Tools The VNMG160404-NFT WSM20S is an indexable turning insert designed for heavy-duty machining of rostfreier Stahl and heat-resistant superalloys, offering a negative rake geometry for secure cutting-edge stability. Tiger·tec Silver coated grade WSM20S Designed for rostfreier Stahl and superalloys Rhombic 35° VNMG insert, 0.4 mm corner radius Boost throughput on difficult-to-cut materials The coated WSM20S carbide grade, part of the Tiger·tec Silver family, is formulated for machining rostfreier Stahl and high-temperature alloys. The combination of a wear-resistant coating and a tough carbide substrate promotes stable chip formation and extends tool life, which reduces unplanned tool changes and keeps machining cycles predictable. For production environments this means fewer interruptions and a measurable improvement in overall equipment effectiveness (OEE), as the insert tolerates the heat and adhesion tendencies typical of these materials. Secure cutting edge and consistent surface quality Featuring a 0° (negative) rake and a defined NFT chipbreaker, the geometry supports a protected cutting edge and controlled chip flow. The 0.4 mm corner radius helps maintain edge strength during interrupted cuts, lowering the risk of chipping while still delivering consistent surface finish. Translating geometry into benefit: stronger edges equal longer life and steadier dimensional results, making the insert suitable for both roughing and semi-finishing operations where repeatability is essential. Flexible integration into established tooling systems The VNMG160404-NFT format (16 mm) conforms to common toolholder interfaces, allowing straightforward insertion into existing turret and holder systems. The rhombic 35° shape provides a versatile approach angle for diverse turning tasks, enabling better access in shoulder and profile work. With a recognised ISO designation and stable tolerance class M, this insert supports predictable tool assembly and simplifies inventory management for workshops aiming to standardise tooling across machines. Contact Metav Werkzeuge for tailored cutting data and stock availability of Walter Tools Tiger·tec Silver inserts to match specific rostfreier Stahl applications and machining conditions Technical Data Article number: VNMG160404-NFT-WSM20S-WALTER Name: VNMG160404-NFT WSM20S Manufacturer: Walter Tools Product type: Drehwendeschneidplatte (indexable turning insert) Series: Tiger·tec Silver Facts Plate size: 16 Plate thickness: 04 Corner radius: 0.4 mm Relief angle: 0° (negative) Plate form: Rhombus 35° Tolerance class: M Special features Grade: WSM20S Chipbreaker: NFT Execution: G Material suitability: S / M Suitable for: rostfreier Stahl and heat-resistant superalloys FAQ What materials is this insert best suited for? The VNMG160404-NFT WSM20S insert is optimised for machining rostfreier Stahl and heat-resistant superalloys (ISO groups M and S) thanks to its Tiger·tec Silver coating and robust carbide core. How does the 0° negative rake affect performance? A 0° negative rake increases cutting-edge strength and resistance to mechanical and thermal shock; the VNMG geometry supports tougher cutting conditions and improves edge life in interrupted or heavily loaded cuts. Can this insert deliver acceptable surface finishes? Yes. While primarily aimed at productive machining, the combination of the 0.4 mm corner radius and the NFT chipbreaker helps achieve consistent surface quality in semi-finishing and finishing passes when cutting parameters are optimised. Is this insert compatible with standard VNMG toolholders? The VNMG160404-NFT format corresponds to widely used toolholder interfaces, enabling straightforward replacement and integration into existing turning setups. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Protected trademarks and trade names remain the property of their respective owners. Brand names and registered trademarks are mentioned for clarification purposes only and do not imply any affiliation with our company. The offered item is an original, factory-new product from the manufacturer (Walter Tools).
VNMG160404-NMS WSM10S WSM10S Wendeplatten - Walter Tools
Take advantage of a proven combination of Tiger·tec Silver coating and the WSM10S grade for secure chip control and extended tool life when machining stainless steels and superalloys; order the insert directly via Metav Werkzeuge or contact our consultants for application advice. VNMG160404-NMS WSM10S — Tiger·tec Silver turning insert, rhombic 35°, for stainless steels and superalloys — Walter Tools A VNMG160404-NMS WSM10S is a rhombic 35° turning insert engineered for robust cutting in demanding materials, offering a 0.4 mm corner radius and a negative 0° relief for stable seating during heavy or interrupted cuts. Tiger·tec Silver coated carbide grade WSM10S Reliable chip control with NMS chipbreaker Suitable for stainless steels and superalloys High process security for demanding materials The WSM10S grade, applied within the Tiger·tec Silver coating family, is formulated for stainless steels (ISO M) and heat-resistant superalloys/titanium (ISO S). This combination enhances thermal resistance and edge durability, which translates into fewer tool changes and more consistent cycle times in batch production. By selecting a grade optimised for poor heat conduction and built-up edge tendencies, machinists gain stable chip formation and predictable wear behaviour that support higher productivity. Reliable chip control and surface quality Equipped with the NMS chipbreaker, the insert promotes controlled chip segmentation in long-chipping materials, reducing the risk of entanglement and improving swarf evacuation. The rhombic 35° geometry combined with a 0.4 mm corner radius helps to balance edge strength and surface finish, delivering improved workpiece integrity on each pass. For operations where reproducibility and reduced secondary finishing are priorities, this geometry enables smoother, more consistent results. Robust seat and interrupted-cut capability The specification shows a negative 0° relief, providing a firm cutting-edge support and minimising insert movement under heavy radial loads. Such a relief angle is advantageous in interrupted cuts or when machining parts with variable engagement. The coated carbide substrate of the grade offers abrasion resistance and keeps the cutting edge sharper for longer, supporting extended tool life without sacrificing process reliability. Practical versatility for production environments With an ISO designation of VNMG160404-NMS and standard plate size, the insert fits common toolholders for turning operations and is suitable for both continuous and semi-finished production runs. The grade’s purpose is to reduce downtime through consistent edge behaviour and to maintain component tolerances across series production. For shops processing a mix of stainless steels and superalloys, the insert provides a focused solution that eases tool management and supports repeatable machining strategies. Contact Metav Werkzeuge for tailored advice and to order this Walter Tools Tiger·tec Silver VNMG160404-NMS WSM10S insert; eMail: info@metav-werkzeuge.com — Tel: +49 2822 7131930 Technical Data SKU: VNMG160404-NMS-WSM10S-WALTER Name: Drehwendeschneidplatte VNMG160404-NMS WSM10S Manufacturer: Walter Tools Series: Tiger·tec Silver Facts Plate size: 16 Thickness code: 04 Corner radius: 0.4 mm Relief angle: 0° (negative) Shape: Rhombus 35° Tolerance class: M Special features Grade: WSM10S (coated carbide) Chipbreaker: NMS Applicable materials: S / M (superalloys/titanium and stainless steels) Execution: G Inscribed designation: VNMG160404-NMS WSM10S FAQ What materials is this insert designed for? The VNMG160404-NMS WSM10S insert by Walter Tools is intended for stainless steels (ISO M) and heat-resistant superalloys/titanium (ISO S), offering secure chip formation and thermal resistance for these groups. How does the NMS chipbreaker affect machining? The NMS chipbreaker on this Walter Tools turning insert produces compact chips and improves evacuation, which reduces swarf issues and supports consistent surface quality during long or difficult cuts. Is the negative 0° relief suitable for interrupted cuts? Yes, the negative 0° relief provides strong support at the cutting edge, making the insert well suited to interrupted cutting and operations with varying engagement. What benefit does the Tiger·tec Silver coating offer? The Tiger·tec Silver coating enhances thermal stability and wear resistance on the WSM10S grade, extending tool life and supporting stable machining when processing demanding alloys and stainless steels. Which geometry features contribute to surface finish? The rhombic 35° form together with a 0.4 mm corner radius balances edge strength and finishing capability, helping to maintain dimensional accuracy and surface integrity across production runs. Manufacturer / Responsible: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen; Germany Protected trademarks and product names are the property of their respective owners. Brand names and registered trademarks are mentioned for explanatory purposes only; there is no affiliation between our company and the named brands. The offered item is an original, factory-new product of the manufacturer Walter Tools.
VNMG160404-NMS WSM20S NMS Wendeplatten - Walter Tools
Benefit from the combination of Tiger·tec Silver coating, a robust NMS chipbreaker and the 0° negative rake for secure, repeatable turning of stainless steels and heat-resistant alloys; order via Metav Werkzeuge or ask its consultants for application guidance. VNMG160404-NMS WSM20S indexable turning insert — Tiger·tec Silver, negative 0° | Walter Tools The VNMG160404-NMS WSM20S is an indexable turning insert engineered for demanding turning applications on stainless steels and heat‑resistant superalloys, delivering stable chip formation and long tool life. Tiger·tec Silver coated carbide Optimised chip control with NMS breaker Negative 0° rake for secure cutting Rhombic 35° shape for versatile engagement Reliable performance on stainless steels and superalloys The combination of the Tiger·tec Silver coating and the WSM20S grade gives a clear advantage when tackling materials that tend to work‑harden or generate high cutting temperatures. The coated cemented carbide substrate improves thermal resistance and wear behaviour, which translates into longer tool life and more consistent component surfaces. For production environments where reproducible results matter, this specification reduces unscheduled tool changes and helps maintain cycle‑time stability. Stable chip control and predictable edge life The NMS chipbreaker is designed to create short, controlled chips in difficult‑to‑cut materials. This promotes secure chip evacuation and reduces the risk of built‑up edge, which is a common challenge when machining austenitic stainless steels. The practical benefit is fewer interruptions for chip management and a reduced need for manual cleaning, contributing to a steadier production flow and improved process efficiency. Geometry tuned for secure turning and versatility With a rhombic 35° shape and a 0.4 mm corner radius, the insert supports both finishing and medium turning tasks while maintaining a stable cutting edge. The 0° (negative) rake increases cutting edge strength and is particularly useful where robustness is required, for example with interrupted cuts or hard inclusions. This geometry enables machinists to achieve a balance between surface quality and tool lifetime without frequent set‑up changes. Application advice and process reliability This grade is intended primarily for stainless steels (ISO M) and for heat‑resistant alloys/titanium (ISO S) depending on component design and cutting parameters. The insert’s specification suits workshops seeking a single, reliable grade for a range of demanding materials, reducing tool inventory complexity. For best results, pair the insert with rigid tooling and stable clamping to exploit its edge stability; suitable feeds and speeds will vary with component geometry and machine capability. Contact Metav Werkzeuge for tailored application recommendations on Walter Tools Tiger·tec Silver inserts — expert guidance and quick delivery for the VNMG160404-NMS WSM20S is available via email at info@metav-werkzeuge.com or by phone on +49 2822 7131930 Technical Data Article number: VNMG160404-NMS-WSM20S-WALTER Manufacturer: Walter Tools Product type: Indexable turning insert (Drehwendeschneidplatte) Designation: VNMG160404-NMS WSM20S Facts Insert size: 16 mm Thickness: 04 Corner radius: 0.4 mm Plate form: Rhombic 35° Free/relief angle: 0° (negative) Tolerance class: M Special features Coating/series: Tiger·tec Silver Grade/sort: WSM20S Chipbreaker: NMS Material suitability: stainless steels (ISO M), superalloys/titanium (ISO S) Intended use: machining of difficult‑to‑cut materials; enhanced edge stability FAQ What materials is this insert suitable for? The VNMG160404‑NMS WSM20S is specified for stainless steels (ISO M) and for heat‑resistant superalloys or titanium (ISO S), offering reliable performance where heat resistance and secure chip formation are required. How does the Tiger·tec Silver coating benefit machining? The Tiger·tec Silver coating increases thermal resistance and wear protection of the cemented carbide substrate, which improves edge life and maintains consistent surface finish during extended turning operations. Why choose a negative 0° rake for turning? A 0° negative rake increases the robustness of the cutting edge, making the insert less prone to chipping during interrupted cuts or when machining materials with hard inclusions, thus enhancing process reliability. What is the role of the NMS chipbreaker? The NMS chipbreaker produces short, controllable chips in difficult materials, aiding chip evacuation and reducing the likelihood of built‑up edge — this supports uninterrupted production and reduces manual chip handling. Manufacturer/Responsible: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen; Germany Geschützte Markenzeichen und Warenbezeichnungen liegen im Recht ihrer jeweiligen Eigentümer. Markennamen und geschützte Warenzeichen werden ausschließlich zu Erklärungszwecken genannt. Es besteht keinerlei Verbindung zwischen unserem Unternehmen und den genannten Marken. Es handelt sich bei dem angebotenen Artikel um originale fabrikneue Waren des Herstellers.
VNMG160408-FM5 WMP20G WMP20G Wendeplatten - Walter Tools
Choose the VNMG160408-FM5 WMP20G for reliable chip control and extended tool life: the Tiger·tec Gold coating and FM5 chipbreaker combine to tame heat and produce stable edges in rostfreier Stahl. Benefit from the Rhombus 35° geometry and 0° negative rake for robust turning operations. Order directly via Metav Werkzeuge or consult our technical advisors for application-specific recommendations. VNMG160408-FM5 WMP20G indexable insert — Rhombus 35°, 0.8 mm nose radius, for rostfreier Stahl (Walter Tools) VNMG160408-FM5 WMP20G is an indexable turning insert designed for medium to heavy-duty machining of rostfreier Stahl; its geometry and grade suit demanding shopfloor conditions Tiger·tec Gold coating for extended tool life FM5 chipbreaker for stable chip control Rhombus 35° geometry with 0.8 mm corner radius 0° negative rake for robust cutting performance Consistent chip control and longer tool life for demanding turning The combination of the FM5 chipbreaker and the Tiger·tec Gold coating delivers measurable improvements in chip formation and wear resistance. The chipbreaker is engineered to produce short, controllable chips when machining rostfreier Stahl, reducing the risk of built-up edge and improving component surface finish. The coating's multi-layer structure supports higher thermal stability and wear resistance, which translates into longer intervals between index changes and fewer unplanned stops. For production environments where cycle-time reliability matters, this insert sustains a predictable tool life and helps maintain process stability. Geometry engineered for stability and reliable cutting results The Rhombus 35° shape and 0.8 mm nose radius provide a balance between strength and profile definition: the nose radius supports a fine surface finish while the inclined geometry reduces cutting forces during interrupted cuts. The 0° negative rake delivers a robust cutting edge, especially advantageous in tougher stainless conditions where material toughness and heat generation are high. These geometric choices ensure the insert resists chipping under heavier depths of cut and provides repeatable dimensional accuracy—qualities that support efficient, high-quality turning in both batch and continuous production. Application guidance and selection rationale for greater process security Assigned to ISO group M, this grade is optimised for rostfreier Stahl under medium to heavy machining conditions. The WMP20G carbide grade is a coated cemented carbide designed to resist adhesion and thermal softening, facilitating steady cutting at typical stainless turning speeds. When selecting cutting parameters, favour moderate to high cutting speeds with stable feeds and ensure appropriate coolant or cutting fluid management to dissipate heat; this helps exploit the Tiger·tec Gold benefits fully. The insert’s design supports both roughing and semi-finishing tasks, offering a cost-effective combination of life expectancy and surface quality in industrial turning applications. For application-specific advice or to secure fast supply of Walter Tools VNMG160408-FM5 WMP20G inserts, contact Metav Werkzeuge for tailored recommendations and order coordination. Technical Data Article number: VNMG160408-FM5-WMP20G-WALTER SKU: VNMG160408-FM5-WMP20G-WALTER Product type: Drehwendeschneidplatte (indexable insert) Manufacturer: Walter Tools Series: Tiger-tec Gold Grade: WMP20G Designation: VNMG160408-FM5 Facts Plate form: Rhombus 35° Inscribed circle/size: 16 Thickness: 04 Corner radius: 0.8 mm Chipbreaker: FM5 Rake angle: 0° negative Tolerance class: M Special features Coating technology: Tiger·tec Gold Carbide grade: WMP20G (coated cemented carbide) Application group: M (rostfreier Stahl) Suitable for medium to robust conditions Robust edge for interrupted cuts Optimised for secure chip formation FAQ What materials is this insert intended for? The VNMG160408-FM5 WMP20G insert is intended primarily for rostfreier Stahl and covers medium to robust stainless turning tasks. Which geometry features improve surface finish and stability? The Rhombus 35° geometry combined with a 0.8 mm corner radius and 0° negative rake provides a strong edge for stable cutting and helps achieve a consistent surface finish. How does the Tiger·tec Gold coating benefit tool life? The Tiger·tec Gold coating increases thermal and wear resistance, helping the WMP20G grade maintain a stable cutting edge and extend intervals between index changes. Is the insert suitable for interrupted cuts and roughing? Yes, the negative rake and robust grade make the insert well suited to interrupted cuts and roughing operations in rostfreier Stahl. What does FM5 chipbreaker contribute to the process? The FM5 chipbreaker produces controllable chip shapes that reduce the risk of built-up edge and make chip evacuation more reliable during turning. Manufacturer: The Walter AG (brand: Walter Tools) with headquarters in Tübingen belongs to the Sandvik Group. Protected trademarks and product names are the property of their respective owners. The named tools are original, factory-new products of the manufacturer.
VNMG160408-FM5 WSM10S WSM10S Wendeplatten - Walter Tools
Benefit from the combination of Tiger·tec Silver coating, proven WSM10S grade and a precise 0.8 mm corner radius for reproducible cutting and extended edge life. Order the VNMG160408-FM5 WSM10S turning insert via Metav Werkzeuge or consult our specialists for grade selection and application advice. VNMG160408-FM5 WSM10S – Turning insert for stainless steels and superalloys | Walter Tools A VNMG160408-FM5 WSM10S indexable turning insert engineered for heavy-duty machining of rostfreier Stahl and heat-resistant superalloys, featuring Tiger·tec Silver coating for thermal stability. Tiger·tec Silver coating for heat resistance WSM10S grade for stainless steel & superalloys Rhombic 35° form with 0.8 mm corner radius Negative 0° rake for stable cutting Optimised process stability for demanding materials The Tiger·tec Silver coating combined with the WSM10S carbide grade provides a balanced solution for machining rostfreier Stahl and high-temperature alloys. This composition is designed to resist thermal softening and to maintain edge stability under continuous load, which leads to fewer unscheduled tool changes and improved process predictability. The insert’s geometry allows for effective heat management during turning, supporting consistent surface quality and reduced risk of built-up edge when cutting tough, heat-generating workpieces. Reliable chip control and predictable tool life Equipped with the FM5 chipbreaker and a negative 0° rake, this insert promotes controlled chip formation and evacuation, avoiding tangled chips and minimising interruptions. The 0.8 mm corner radius contributes to mechanical strength at the cutting edge, distributing cutting forces to lower the likelihood of chipping. For production environments where cycle time and stability are critical, the result is a measurable increase in uptime and a reduction in tool consumption, making the geometry particularly suitable for heavy roughing and mixed-operation turning tasks. Compact compatibility and consistent results across setups The Rhombus 35° shape and standard VNMG form ensure broad compatibility with common toolholders and lathe setups, while the inscribed dimension supports predictable cutting conditions across tool changes. The insert’s series characteristics favour applications where repeatability and consistent results are priorities, enabling straightforward process planning and machining parameter transfer between machines. The combination of coating, grade and form supports a practical compromise between productivity and tool life in industrial turning operations. Contact Metav Werkzeuge for tailored application advice and availability of Walter Tools VNMG160408-FM5 WSM10S inserts Technical Data Article number: VNMG160408-FM5-WSM10S-WALTER Label: Drehwendeschneidplatte VNMG160408-FM5 WSM10S Walter Tools Manufacturer: Walter Tools Series: Tiger·tec Silver Grade: WSM10S Facts Inscribed circle: 16 Corner radius: 0.8 mm Rake angle: 0° (negative) Thickness: 04 Tolerance class: M Special features Coating: Tiger·tec Silver (coated carbide) Grade suitability: S / M (superalloys/titanium and rostfreier Stahl) Chipbreaker: FM5 Insert shape: Rhombus 35° Application: Designed for difficult-to-machine materials and, depending on geometry, rostfreier Stahl FAQ Which materials is this insert suited to machine? The VNMG160408-FM5 WSM10S insert is designed primarily for rostfreier Stahl and heat-resistant superalloys (S / M), offering thermal stability and edge resistance for these groups. What are the advantages of the Tiger·tec Silver coating? Tiger·tec Silver enhances the thermal resistance and wear behaviour of the cutting edge on the VNMG160408-FM5, leading to improved process security and longer usable edge life in demanding turning operations. How does the FM5 chipbreaker influence machining? The FM5 chipbreaker on this insert promotes controlled chip formation and evacuation, reducing the risk of chip entanglement and supporting consistent surface finish during extended cuts. Manufacturer/Responsible: AB Sandvik Coromant, Mossvägen 10, 811 34 Sandviken, Sweden, support.coromant@sandvik.com Protected trademarks and trade names are the property of their respective owners. Brand names and protected trade names are mentioned solely for explanation. There is no connection between our company and the named brands. The offered item is an original, factory-new product of the manufacturer Walter Tools.
VNMG160408-FM5 WSM20S WSM20S Wendeplatten - Walter Tools
Take advantage of the combination of high process stability, targeted chip control and robust edge life for reliable turning in demanding materials; order the insert directly via Metav Werkzeuge or consult our specialists for application-specific recommendations. VNMG160408-FM5 WSM20S – Indexable turning insert with Tiger·tec Silver, for rostfreier Stahl and superalloys (Walter Tools) VNMG160408-FM5 WSM20S is a rhombic 35° indexable turning insert designed for heavy-duty and heat-resistant alloys, offering a coated carbide grade for stable cutting and controlled chip formation Tiger·tec Silver coating for high temperature stability Optimised FM5 chipbreaker for reliable chip control Rhombic 35° shape with 0.8 mm corner radius Negative 0° rake for stable cutting performance Consistent cutting on tough materials for fewer interruptions The combination of the Tiger·tec Silver coating and the WSM20S grade delivers improved heat resistance and a reliable cutting edge when machining rostfreier Stahl and heat-resistant superalloys. The coated carbide substrate supports stable chip formation, reduces the tendency for built-up edge and extends effective tool life. For production environments where unpredictable tool wear causes downtime, this insert helps to maintain cycle times and component quality without frequent regrinds, so machining remains predictable and cost-efficient. Precise chip control and predictable surface quality The FM5 chipbreaker is engineered to produce short, consistent chips on a range of feeds and depths, improving swarf handling and process security. Combined with the rhombic 35° geometry and a 0.8 mm corner radius, the insert balances edge strength and cutting access, enabling smooth surface finishes with fewer passes. The negative 0° rake increases edge stability for intermittent cuts and heavy cross-sections, resulting in fewer edge failures and more consistent part tolerances during serial production. Practical selection for workshop and production use As part of the Tiger·tec Silver series, this insert integrates into standard VNMG toolholder systems and is available under the ISO designation VNMG160408-FM5 WSM20S, simplifying inventory and tool choice. The specification supports machining of both the M and S ISO groups (rostfreier Stahl; heat‑resistant superalloys and Titan), which reduces the need for multiple special grades and streamlines process planning. For tailored recommendations on feeds, speeds and holder choice, technical advice is available via Metav Werkzeuge — contact details are provided for rapid consultation. For fast application support on Walter Tools inserts and to ensure optimal performance when machining rostfreier Stahl or superalloys, contact Metav Werkzeuge at info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: VNMG160408-FM5-WSM20S-WALTER ISO designation: VNMG160408-FM5 WSM20S Product type: Indexable turning insert Brand: Walter Tools Core dimensions Corner radius: 0.8 mm Inscribed circle / plate size: 16 mm Plate thickness: 04 Free rake angle: 0° (negative) Insert geometry: Rhombic 35° Tolerance class: M Special features Coating: Tiger·tec Silver Grade / sort: WSM20S Chipbreaker: FM5 Material group applicability: S / M Recommended for: rostfreier Stahl and heat‑resistant superalloys / Titan Series: Tiger‑tec Silver FAQ Which materials is this insert best suited for? The VNMG160408-FM5 WSM20S from Walter Tools is optimised for rostfreier Stahl and for heat‑resistant superalloys and Titan, reflecting the S and M ISO material groups listed for this grade. How does the FM5 chipbreaker affect production? The FM5 chipbreaker produces controlled, compact chips that improve swarf evacuation and reduce the risk of chip entanglement, enhancing process reliability with the VNMG160408-FM5 WSM20S insert. Is the geometry suitable for finishing and heavy cuts? The rhombic 35° geometry with a 0.8 mm corner radius and negative 0° rake provides a robust edge for heavier engagements while still allowing for good surface quality in finishing passes on demanding materials. Can this insert be used in standard VNMG toolholders? Yes, the VNMG form follows the common ISO VNMG specification, making the VNMG160408-FM5 WSM20S compatible with standard toolholders designed for VNMG inserts. Where to get application data for cutting speeds and feeds? Application parameters depend on component material, machine rigidity and coolant use; for specific recommendations for the VNMG160408-FM5 WSM20S, Metav Werkzeuge can provide tailored guidance. Manufacturer / Responsible: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen; Germany Geschützte Markenzeichen und Warenbezeichnungen liegen im Recht ihrer jeweiligen Eigentümer. Markennamen und geschützte Warenzeichen werden ausschließlich zu Erklärungszwecken genannt. Es besteht keinerlei Verbindung zwischen unserem Unternehmen und den genannten Marken. Es handelt sich bei dem angebotenen Artikel um originale fabrikneue Waren des Herstellers.
VNMG160408-FP5 WEP10C WEP10C Wendeplatten - Walter Tools
Take advantage of the WEP10C cermet grade and the FP5 chipbreaker to improve cutting stability and reduce tool changes; the rhombic 35° geometry with a 0.8 mm corner radius supports consistent surface quality while the 0° negative rake offers robust performance in interrupted cuts. Order the insert directly via Metav Werkzeuge or contact the sales consultants for application support. VNMG160408-FP5 WEP10C — Turning insert, Rhombus 35°, Walter Tools The VNMG160408-FP5 WEP10C is a cermet turning insert designed for precision turning tasks where tool life and surface quality are prioritised Cermet grade WEP10C for excellent wear resistance Rhombic 35° geometry for versatile turning 0° negative rake for stable machining 0.8 mm corner radius for dependable edge strength Longer tool life through advanced cermet technology The Walter WEP10C is a cermet cutting grade developed for wear resistance and consistent edge performance. Combining a hard, wear‑resistant substrate with fine microstructure yields extended tool life and fewer insert changes, which supports continuous production runs and reduces downtime. For process planners, this translates into improved parts-per‑tool metrics and lower cost per component when compared with conventional grades in finishing applications. Predictable chip control and stable cutting performance The FP5 chipbreaker paired with a 0° negative rake promotes predictable chip formation and stable cutting forces. This geometry is particularly effective in maintaining consistent cutting behaviour during light to medium finishing passes and when dealing with variable cut engagement. The result is reduced vibration, improved machining reliability and fewer surface defects, supporting high process stability across batch production. Geometry engineered for accurate surfaces and edge strength The rhombic 35° insert geometry and 0.8 mm corner radius balance accessibility and strength: the slim approach angle allows close work on fillets and profiles, while the corner radius increases edge resilience for consistent surface finish. The plate thickness and form support secure clamping and repeatable positioning, which helps to maintain dimensional accuracy and reduce set‑up variation in automated turning cells. Integration advice and material suitability checks The insert belongs to the Walter Cermet series and is optimised for productive finishing applications; material compatibility should be verified against the official product matrix before process implementation. Matching cut parameters to the cermet behaviour—higher cutting speeds and moderate feeds—will exploit the grade’s strengths. For tailored recommendations or trial suggestions, process engineers are encouraged to consult the technical team to confirm the best parameters for the intended workpiece material. Contact Metav Werkzeuge for tailored application advice on the Walter Cermet WEP10C inserts or to arrange a cutting parameter review: info@metav-werkzeuge.com · +49 2822 7131930 Technical data Article number: VNMG160408-FP5-WEP10C-WALTER Designation: VNMG160408-FP5 Series: Walter Cermet Grade: WEP10C Manufacturer: Walter Tools Facts Insert size: 16 Thickness: 04 Corner radius: 0.8 mm Free angle: 0° (negative) Tolerance class: M Special features Chipbreaker: FP5 Plate form: Rhombus 35° Cermet cutting grade Stable edge preparation for finishing FAQ What is the main advantage of the WEP10C grade? The WEP10C cermet grade provides high wear resistance and consistent edge life, making the VNMG160408-FP5 WEP10C insert suitable for finishing operations that demand prolonged tool life. Can the FP5 chipbreaker handle interrupted cuts? Yes, the FP5 chipbreaker combined with a 0° negative rake supports stable cutting in interrupted conditions, aiding reliable chip control and reduced vibration. How should cutting parameters be adapted for this cermet insert? Higher cutting speeds with moderate feeds are typically recommended to exploit the Walter Cermet characteristics; check the product matrix and run validation tests to define optimal parameters. Is the VNMG160408-FP5 compatible with all steels and alloys? Material suitability must be confirmed via the manufacturer's product matrix; the insert is designed for productive finishing but specific workpiece materials should be checked before production use. Where can further technical information be obtained? Detailed specifications and process support are available from Metav Werkzeuge; technical enquiries can reference the VNMG160408-FP5 WEP10C insert for precise guidance. Manufacturer: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen; Germany Protected trademarks and trade names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The offered item is original, factory‑new merchandise from the manufacturer.
VNMG160408-FP5 WKP01G WKP01G Wendeplatten - Walter Tools
Benefit from the combination of Tiger·tec Gold coating and the WKP01G grade for consistent tool life and reliable chip control, ensuring uninterrupted production. Order the VNMG160408-FP5 WKP01G turning insert directly via Metav Werkzeuge or consult our specialists for application-specific cutting data. VNMG160408-FP5 WKP01G turning insert — Tiger·tec Gold, for steel & cast iron, Walter Tools The VNMG160408-FP5 WKP01G is a rhombic 35° negative-geometry turning insert designed for productive machining of steel and cast iron, optimised for stable chip formation and long tool life. Tiger·tec Gold coating for long tool life Suitable for steel and cast iron (P, K) Rhombic 35° form with 0° negative clearance FP5 chipbreaker, 0.8 mm corner radius Improved wear resistance for extended production runs The Tiger·tec Gold coating combined with the WKP01G cutting grade provides enhanced wear resistance and consistent performance under heavy-duty turning conditions. As a coated carbide grade, it is engineered to withstand the thermal and abrasive loads typical when machining steels and cast irons, which reduces the frequency of insert changes and supports higher overall equipment effectiveness. The result is more predictable tool life and fewer unscheduled interruptions in serial production. Reliable surface quality with controlled chip formation The FP5 chipbreaker and the Rhombus 35° geometry deliver controlled chip shaping and evacuation, promoting a steady cutting process and improved part surface finish. The 0° negative clearance contributes to a stable cutting edge under interrupted cuts and moderate depths of cut, helping to avoid vibration-induced deterioration of the workpiece surface. Together, these features support reproducible quality and reduce post-process rework. Broad material coverage reduces tool inventory Designed for the ISO groups P (steel) and K (cast iron), this insert covers a wide range of common workpiece materials. In practice, that means fewer grades are required to handle mixed production runs, lowering inventory complexity and simplifying tooling decisions. For customers less familiar with ISO group codes: P designates typical steels (unalloyed and alloyed), while K refers to various cast iron types; the WKP01G grade is optimised for the thermal and chip-forming behaviours of both groups. Precision fit and consistent production results With a plate size of 16, thickness 04 and a corner radius of 0.8 mm, the insert conforms to common VNMG dimensions and is manufactured to tolerance class M, ensuring repeatable seating and interchangeability in standard VNMG toolholders. The consistent tolerance supports reliable clamping and stable cutting geometry, which in turn contributes to dimensional repeatability on machined parts and predictable tool performance in shop-floor processes. For tailored cutting data, availability checks or recommendations for Walter Tools Tiger·tec Gold inserts, contact Metav Werkzeuge for application support and sample suggestions via info@metav-werkzeuge.com or +49 2822 7131930 Technical Data Article number: VNMG160408-FP5-WKP01G-WALTER Type: Turning insert Designation: VNMG160408-FP5 WKP01G Series: Tiger·tec Gold Manufacturer: Walter Tools Facts Plate size: 16 Thickness: 04 Corner radius: 0.8 mm Clearance angle: 0° (negative) Plate form: Rhombus 35° Tolerance class: M Special features Coating: Tiger·tec Gold Grade: WKP01G (coated carbide) Chipbreaker: FP5 Material suitability: steel (P), cast iron (K) Main applications: productive turning, stable chip control FAQ What materials can be machined with this insert? The VNMG160408-FP5 WKP01G from Walter Tools is designed for steel (P) and cast iron (K) in accordance with ISO 513 recommendations. What is the purpose of the FP5 chipbreaker? The FP5 chipbreaker shapes and controls chips to improve evacuation and surface finish when using the VNMG160408-FP5 WKP01G insert in turning operations. How does the 0° negative geometry affect cutting? A 0° negative clearance offers a robust cutting edge suitable for interrupted cuts and stable roughing, increasing process security during demanding operations. Is the corner radius of 0.8 mm suitable for finishing? The 0.8 mm corner radius balances strength and surface quality; it is well suited for medium-depth turning where a compromise between edge robustness and finish is required. What does tolerance class M mean for tool fit? Tolerance class M indicates a medium tolerance level, ensuring reliable seating and repeatable clamping in standard VNMG toolholders for consistent production results. Manufacturer: Walter Tools; Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen, Germany Trademarks and trade names are the property of their respective owners. Brand names and protected trade names are mentioned for explanatory purposes only. There is no connection between our company and the mentioned brands. The offered item is original, brand-new goods from the manufacturer.
VNMG160408-FP5 WPP10G WPP10G Wendeplatten - Walter Tools
Take advantage of the combination of Tiger·tec Gold coating and the WPP10G grade for consistent, long-lasting performance in steel turning; the robust rhombic geometry and FP5 chipbreaker provide reliable chip control and stable cutting forces. Order directly via Metav Werkzeuge or contact our consultants for application advice. VNMG160408-FP5 WPP10G — turning insert, Tiger·tec Gold, for steel — Walter Tools A VNMG160408-FP5 WPP10G is a rhombic 35° turning insert with a Tiger·tec Gold coating, designed for reliable steel machining in general turning operations Tiger·tec Gold coating for extended life Optimised for steel (ISO P) Rhombic 35° geometry, 0.8 mm radius Negative 0° rake for stable cutting Longer uptime through premium coating and grade The Tiger·tec Gold technology combined with the WPP10G grade identifies a coated carbide solution optimised for steel (ISO P). The coating improves abrasion resistance and reduces flank wear during continuous turning, which results in longer tool life and fewer insert changes. In practice, this means more uninterrupted production time and lower tooling consumption, supporting higher process efficiency and predictable machining cycles. Consistent chip control and mechanical stability With the integrated chipbreaker FP5 and a rhombic 35° shape, the insert delivers controlled chip formation for a wide range of cutting depths. The 0.8 mm corner radius and negative 0° rake increase edge strength and reduce the tendency to chip under interrupted cuts or heavier engagement. These geometry choices contribute to stable cutting and reduce vibration, resulting in more consistent surface quality and repeatable results on steel components. Practical benefits for workshop productivity The designation VNMG160408-FP5 reflects a standardised insert geometry with a thickness code and chipbreaker tailored to turning applications; this standardisation simplifies tooling selection and inventory management. The combination of a robust grade and the FP5 chip control makes the insert suitable for both roughing and medium finishing operations on steel, enabling shops to streamline setups and maintain throughput. The overall effect is improved process reliability and better capacity utilisation on production lines. Contact Metav Werkzeuge today for technical recommendations on Walter Tools VNMG160408-FP5 WPP10G inserts and to discuss suitable cutting data for specific steel grades — eMail: info@metav-werkzeuge.com or call +49 2822 7131930 Technical Data Article number: VNMG160408-FP5-WPP10G-WALTER Label: Drehwendeschneidplatte VNMG160408-FP5 WPP10G Walter Tools Product type: Drehwendeschneidplatte (turning insert) Manufacturer: Walter Tools Series: Tiger‑tec Gold Grade: WPP10G Facts Insert size: 16 Thickness code: 04 Corner radius: 0.8 mm Geometry: Rhombus 35° Rake angle: 0° (negative) Chipbreaker: FP5 Tolerance class: M Special features Coated carbide grade WPP10G Suitable material group: steel (ISO P) Base designation: VNMG160408-FP5 Designed for stable chip control and productive turning FAQ What materials is this insert designed for? The VNMG160408-FP5 WPP10G is designed primarily for steel (ISO P); the WPP10G grade and Tiger·tec Gold coating are optimised for the heat and chip-forming behaviour typical of steel machining. What does the Tiger·tec Gold coating deliver? Tiger·tec Gold on the WPP10G grade provides enhanced abrasion resistance and improved edge stability on the insert, which helps extend life and maintain consistent cutting performance when machining steel. For which cutting tasks is the FP5 chipbreaker suitable? The FP5 chipbreaker is intended for controlled chip formation during medium to heavy turning operations, offering reliable evacuation and reduced risk of built-up edge when machining various steel grades. How does the rhombic 35° geometry affect performance? The rhombic 35° shape and a 0.8 mm corner radius support stable cutting and access to confined contours; combined with the negative 0° rake, this geometry offers robust edge strength for interrupted cuts and higher engagement. What information is encoded in VNMG160408-FP5? The designation VNMG160408-FP5 denotes the insert family and geometry, with size and radius codes and the integrated FP5 chipbreaker; VNMG identifies the shape, 16 the nominal size, 04 the thickness code and 08 the corner radius code, followed by the chipbreaker type. Hersteller: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Protected trademarks and trade names are the property of their respective owners. Brand names and trademarks are used solely for identification and explanation. There is no affiliation between our company and the trademark owners. The offered item is an original, factory-new product from the manufacturer.
VNMG160408-FP5 WPP20G WPP20G Wendeplatten - Walter Tools
Take advantage of the WPP20G grade and FP5 chipbreaker to achieve stable chip control, reliable edge life and consistent results in steel turning operations; order through Metav Werkzeuge or consult our specialists for tailored recommendations. VNMG160408-FP5 WPP20G indexable turning insert by Walter Tools — Tiger·tec Gold, for steel turning VNMG160408-FP5 WPP20G is a rhombic 35° indexable insert designed for efficient, high‑productivity turning of steel components in industrial machining. Tiger·tec Gold coated grade WPP20G FP5 chipbreaker for controlled chip formation Rhombic 35° geometry for versatile turning 0.8 mm nose radius for edge strength 0° negative rake for stable cutting High-performance grade engineered for steel machining The WPP20G grade from the Tiger·tec Gold series is a coated carbide formulation developed for the thermal and mechanical demands of machining steel (ISO group P). Its composition and coating deliver stable chip formation and improved wear resistance, which translates into longer intervals between tool changes and greater process reliability. Where consistent surface finish and repeatable dimensional accuracy are priorities, this cutting grade reduces the risk of unexpected tool deterioration and helps maintain steady production output. Geometry and chip control that boost process security The rhombic 35° shape combined with the FP5 chipbreaker provides versatile cutting performance across a wide range of turning tasks. The 0.8 mm nose radius balances edge strength with finish capability, while the 0° negative rake enhances cutting stability under heavy or interrupted cuts. These geometric choices support predictable chip flow and minimise vibration, so the insert delivers consistent engagement with the workpiece and contributes to process security in demanding shop environments. Measurable productivity and economy benefits Using this insert reduces downtime through longer tool life and repeatable performance, which can improve machine utilisation rates. The combination of Tiger·tec Gold coating and the FP5 chipbreaker often results in fewer edge failures and better wear behaviour on steel grades, delivering a clear cost‑benefit over many production cycles. For operations aiming to raise throughput without compromising component quality, the insert offers an efficient route to more productive turning cycles and reduced scrap rates. Practical selection and integration guidance The insert is suited for standard indexable toolholders that accept VNMG geometry and is optimised for machining steels as defined by ISO group P. When pairing with tooling and setting cutting parameters, aim for conditions that take advantage of the coating’s wear resistance and the FP5 chip control—this typically means stable feeds and monitoring for optimal edge life. For applications requiring tailored feed or speed data, compatibility checks with the chosen toolholder and machine rigidity are recommended to ensure the best outcome. For availability and technical advice on Walter Tools’ VNMG160408-FP5 WPP20G indexable insert for steel turning, contact Metav Werkzeuge via info@metav-werkzeuge.com or call +49 2822 7131930. Technical data Article number: VNMG160408-FP5-WPP20G-WALTER Designation: VNMG160408-FP5 WPP20G Manufacturer: Walter Tools Product type: Indexable turning insert (Drehwendeschneidplatte) Series: Tiger·tec Gold Facts Rhombic angle: 35° Nose radius: 0.8 mm Insert size: 16 Thickness code: 04 Free angle: 0° (negative) Tolerance class: M Special features Coating: Tiger·tec Gold coated carbide (WPP20G) Chipbreaker: FP5 Application: Steel (ISO group P) Execution: G FAQ What materials is this insert intended for? The VNMG160408-FP5 WPP20G insert is optimised for steel machining and is classified for ISO group P; the WPP20G grade is tuned to the thermal and chip‑forming behaviour typical of unalloyed and alloyed steels. What advantages does the WPP20G grade provide? WPP20G is a Tiger·tec Gold coated carbide grade that offers stable chip formation, good wear resistance and broad applicability in steel turning, resulting in predictable tool life and consistent surface quality. How does the FP5 chipbreaker influence performance? The FP5 chipbreaker controls chip formation to produce manageable chips and to reduce the risk of entanglement or unstable cutting; this enhances process security and helps maintain a reliable cutting edge on the insert. Which geometry features support versatile turning applications? The rhombic 35° geometry combined with a 0.8 mm nose radius and a 0° negative rake provides a compromise between strength and finish capability, making the insert suitable for a range of general turning operations. Is the insert compatible with standard VNMG toolholders? Yes, the VNMG160408-FP5 WPP20G conforms to VNMG geometry and is intended for use with compatible indexable toolholders designed for this insert form. Manufacturer: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen; Germany Geschützte Markenzeichen und Warenbezeichnungen liegen im Recht ihrer jeweiligen Eigentümer. Markennamen und geschützte Warenbezeichnungen werden ausschließlich zu Erklärungszwecken genannt. Es besteht keinerlei Verbindung zwischen unserem Unternehmen und den genannten Marken. Es handelt sich bei dem angebotenen Artikel um originale fabrikneue Waren des Herstellers.
VNMG160408-MK5 WKK10S Wendeplatten - Walter Tools
Take advantage of the combination of Tiger‑tec Silver coating, the WKK10S carbide grade and the MK5 chipbreaker for a production-stable turning process on cast iron; order directly via Metav Werkzeuge or consult the sales team for application-specific advice. VNMG160408-MK5 WKK10S – indexable turning insert for cast iron, Tiger‑tec Silver | Walter Tools A VNMG160408-MK5 WKK10S indexable turning insert designed for robust performance when machining cast iron, offering high wear resistance and consistent short-chip behaviour for interrupted and continuous turning Tiger‑tec Silver coating for wear resistance WKK10S grade optimised for cast iron MK5 chipbreaker for controlled short chips Rhombic 35° shape, 0.8 mm corner radius Productive machining of cast iron with extended edge life The combination of the WKK10S coated carbide grade and the Tiger‑tec Silver technology yields a cutting edge engineered for abrasive conditions typical of cast iron. This results in improved wear resistance and a longer service interval between index changes, which supports a more continuous production flow. The coated grade is optimised for the short, brittle chips of cast materials and reduces flank wear under intermittent cuts, helping to sustain component tolerances and surface quality over longer runs. Secure chip control and consistent surface finish The integrated MK5 chipbreaker geometry promotes the formation of short, manageable chips even under interrupted cutting conditions. Combined with the Rhombic 35° geometry and a 0.8 mm corner radius, the insert provides a balance between stable cutting action and the ability to produce a reliable surface finish. The 0° negative rake increases edge robustness for heavy engagement, making the insert suitable where chip control and process security are priorities. Optimal process stability for small and large batch production Tolerance class M and the compact plate size support repeatable seating and low vibration across toolholders that accept VNMG formats. The insert’s construction and geometry contribute to predictable tool life and minimise unscheduled downtime, which in turn enhances overall shop productivity. The design is particularly advantageous for shops seeking a compromise between aggressive material removal and tool economy. Material guidance and application notes for safe integration Classified for ISO group K (cast iron), the grade is tailored to the abrasive wear and brittle chip characteristics of cast materials. The coated, wear‑resistant design is intended for stable cutting parameters rather than extreme high‑speed finishing, and it is well suited to typical cast iron turning tasks where short chips and controlled breaking are required. For tailored cutting data and holder compatibility, refer to tooling system documentation when integrating this insert into existing setups. For application advice, availability and assistance integrating the insert into a machining process, contact Metav Werkzeuge GmbH by phone +49 2822 7131930 or email info@metav-werkzeuge.com to discuss suitability for specific cast iron grades and tooling systems Technical data Article number: VNMG160408-MK5-WKK10S-WALTER SKU: VNMG160408-MK5-WKK10S-WALTER Product type: Indexable turning insert (Drehwendeschneidplatte) Manufacturer: Walter Tools Facts Plate size: 16 Thickness code: 04 Corner radius: 0.8 mm Shape: Rhombic 35° Rake: 0° (negative) Chipbreaker: MK5 Grade: WKK10S Series/coating: Tiger‑tec Silver Tolerance class: M Applicable material: Cast iron (ISO group K) Special features Coated carbide grade WKK10S Optimised for abrasive wear on cast iron Stable cutting edge for interrupted cuts Controlled short-chip formation with MK5 Versatile VNMG format for conventional turning FAQ Is this insert suitable for machining cast iron? Yes. The insert is supplied in the WKK10S grade from the Tiger‑tec Silver series and is specifically optimised for ISO group K (cast iron) applications, where abrasive wear and short chips are common. What does the MK5 chipbreaker deliver in practice? The MK5 chipbreaker promotes short, well controlled chips, improving process stability and reducing the risk of entanglement during turning of brittle or interrupted cast iron sections. How do the geometry and corner radius affect performance? The Rhombic 35° geometry and 0.8 mm corner radius provide a compromise between a robust cutting edge and the ability to achieve consistent surface quality, while the 0° negative rake enhances edge strength for heavier cross‑sections. Which series and coating technology is used for this insert? The insert belongs to the Tiger‑tec Silver series with the WKK10S coated carbide grade, designed for high wear resistance and dependable performance in cast iron turning. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Die Walter AG (Markenauftritt: Walter Tools) mit Hauptsitz in Tübingen gehört zu den weltweit führenden Herstellern von Präzisionswerkzeugen für die Metallbearbeitung und ist Teil des schwedischen Sandvik‑Konzerns. Geschützte Markenzeichen und Warenbezeichnungen liegen im Recht ihrer jeweiligen Eigentümer. Markennamen und geschützte Warenzeichen werden ausschließlich zu Erklärungszwecken genannt. Es besteht keinerlei Verbindung zwischen unserem Unternehmen und den genannten Marken. Es handelt sich bei dem angebotenen Artikel um originale fabrikneue Waren des Herstellers.
VNMG160408-MK5 WKK20S WKK20S Wendeplatten - Walter Tools
Benefit from the combination of the Tiger·tec Silver coating, WKK20S grade and MK5 chipbreaker for productive, repeatable machining of cast iron; order the VNMG160408-MK5 WKK20S turning insert directly via Metav Werkzeuge or request application advice from our consultants. VNMG160408-MK5 WKK20S — Turning insert for cast iron, Tiger·tec Silver by Walter Tools VNMG160408-MK5 WKK20S is a negative‑rake rhombic 35° turning insert designed for reliable finishing and medium‑roughing of cast iron components Tiger·tec Silver coating for long life WKK20S grade tuned for cast iron MK5 chipbreaker for reliable chip control Rhombic 35° with 0.8 mm corner radius Maximise productivity in cast‑iron turning The VNMG160408-MK5 WKK20S insert combines the Tiger·tec Silver coating with a wear‑resistant WKK20S grade to deliver extended tool life when machining cast iron. The coated cemented‑carbide substrate resists abrasive wear typical of grey and nodular cast irons, which reduces the frequency of index changes and supports steady production cycles. The rhombic geometry and negative relief are optimised for stable cutting forces, so cycle times remain consistent even under interrupted cuts, offering a measurable productivity gain in high‑volume turning applications. Consistent chip control and surface quality The integrated MK5 chipbreaker and the 0° (negative) relief angle provide controlled chip formation and evacuation, lowering the risk of built‑up edge and surface damage. A well‑matched chipbreaker reduces heat concentration at the cutting edge and helps maintain a consistent cut, which in turn supports tighter tolerances and repeatable surface finishes. The 0.8 mm corner radius helps balance strength and edge sensitivity, giving a compromise between fine finish capability and resistance to chipping during heavier passes. Simple tooling logistics with reliable repeatability Standard VNMG indexing and the common thickness 04 make the insert straightforward to stock and fit into existing toolholders, while tolerance class M ensures consistent seating and runout behaviour. The combination of proven coating technology and a grade tailored to the demands of cast iron machining delivers predictable wear behaviour, which simplifies process planning and cost forecasts. For operations seeking stable, repeatable results, the insert supports reduced tool change frequency and improved overall equipment effectiveness. Contact Metav Werkzeuge for tailored cutting data, availability of genuine Walter Tools Tiger·tec Silver inserts, or to discuss optimal machining parameters for cast iron components — eMail: info@metav-werkzeuge.com • Tel: +49 2822 7131930 Technical Data SKU: VNMG160408-MK5-WKK20S-WALTER Article designation: VNMG160408-MK5 ISO designation: VNMG160408-MK5 WKK20S Product type: Drehwendeschneidplatte (turning insert) Manufacturer: Walter Tools Core specifications Insert size: 16 Thickness: 04 Corner radius: 0.8 mm Relief angle: 0° (negative) Plate form: Rhombus 35° Tolerance class: M Special features Grade: WKK20S Series: Tiger·tec Silver Chipbreaker type: MK5 Material application: Cast iron (K) Material: coated cemented carbide FAQ What materials is this insert suitable for? The VNMG160408-MK5 WKK20S insert is engineered primarily for cast iron machining; the WKK20S grade and Tiger·tec Silver coating address the abrasive wear and short, breaking chips typical of cast materials. How does the MK5 chipbreaker improve machining? The MK5 chipbreaker on this Walter Tools insert promotes controlled chip formation and reliable evacuation, which helps maintain surface quality and reduces the likelihood of tool‑related interruptions during turning. Is this insert compatible with standard VNMG toolholders? Yes, the VNMG160408-MK5 WKK20S follows standard VNMG geometry and a thickness of 04, making it compatible with common VNMG toolholders where the seat and clamping correspond to tolerance class M. What benefits does the Tiger·tec Silver series provide? Tiger·tec Silver coating improves resistance to abrasive wear and thermal load, extending the effective tool life of the WKK20S grade and contributing to stable, repeatable machining results on cast iron components. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Protected trademarks and trade names are the property of their respective owners. Brand names are mentioned for explanatory purposes only and do not imply any affiliation with Metav Werkzeuge. The offered article is an original, factory‑new product of the manufacturer Walter Tools. The Walter name and trademarks are used solely to describe the product origin and authenticity.
VNMG160408-MM5 WMP20G WMP20G Wendeplatten - Walter Tools
Take advantage of the combination of Tiger·tec Gold coating, a sturdy MM5 chipbreaker, and precise rhombic geometry for reliable machining of rostfreier Stahl; order the VNMG160408-MM5 WMP20G directly via Metav Werkzeuge or consult the team for application advice. VNMG160408-MM5 WMP20G indexable turning insert — Tiger·tec Gold for rostfreier Stahl by Walter Tools A VNMG160408-MM5 WMP20G indexable turning insert engineered for medium to robust machining of rostfreier Stahl, delivering stable chip control and extended tool life in demanding production environments Tiger·tec Gold coating for extended tool life Optimised for rostfreier Stahl machining Rhombic 35° VNMG form with 0.8 mm nose MM5 chipbreaker for secure chip control Consistent tool life through advanced coating and grade The WMP20G grade, realised within the Tiger·tec Gold technology, is a coated carbide solution designed specifically for machining rostfreier Stahl (ISO M). The multi-layer coating reduces flank wear and supports secure chip formation, which in turn lowers the frequency of insert changes and contributes to predictable process stability. In production terms this means fewer interruptions and a more constant quality level across batches—an advantage when cycle time and repeatability matter most. Geometry that balances rigidity and surface quality The rhombic 35° VNMG shape combined with a 0.8 mm nose radius and a 0° negative relief produces a stable cutting edge with good access in turning applications. The geometry favours reduced cutting forces at moderate depths while still enabling consistent surface finish on rotational parts. A larger nose radius supports smoother finishes and reduced machining marks, whereas the negative relief increases edge strength for interrupted or heavier cuts—useful when facing varied part geometries or mixed operations. Secure chip control and application guidance for reliable production The integrated MM5 chipbreaker is tuned to support short, manageable chips when machining rostfreier Stahl, reducing the risk of entanglement and improving operator safety at the tool centre. The insert is suitable for a range of turning tasks under medium to robust conditions; process engineers will find it well suited for both semi-finishing and finishing passes depending on chosen feeds and speeds. For optimal results, match the insert with a compliant toolholder and set cutting data in line with the machine’s rigidity—this combination promotes consistent component accuracy and economical tool utilisation. For production environments requiring reliable, repeatable performance on rostfreier Stahl, specify the Walter Tools VNMG160408-MM5 WMP20G from Metav Werkzeuge and request tailored cutting parameters or application support from the Metav team. Technical data SKU: VNMG160408-MM5-WMP20G-WALTER Article designation: VNMG160408-MM5 WMP20G Product type: Indexable turning insert (drehwendeschneidplatte) Manufacturer: Walter Tools Series/grade: Tiger·tec Gold / WMP20G Core technical data Insert size: 16 mm Nose radius: 0.8 mm Thickness code: 04 Relief angle: 0° (negative) Tolerance class: M Special features Chipbreaker: MM5 Shape: Rhombic 35° Coating/technology: Tiger·tec Gold (coated carbide) Target application: rostfreier Stahl (ISO M) Execution: G FAQ What materials is this insert best suited for? The VNMG160408-MM5 WMP20G is optimised for rostfreier Stahl (ISO M); the Tiger·tec Gold grade supports secure chip formation and wear resistance in these materials. How does the MM5 chipbreaker affect machining? The MM5 chipbreaker produces short, controllable chips, improving safety and reducing chip-related interruptions when machining rostfreier Stahl with this Walter Tools insert. What is the benefit of the 0.8 mm nose radius? A 0.8 mm nose radius balances surface finish and tool strength—larger radii enhance surface quality and distribute cutting forces, useful for semi-finishing and finishing passes. Can this insert handle interrupted cuts or heavier machining? Yes; the rhombic 35° form with negative relief provides additional edge strength, making the insert suitable for interrupted cuts and more robust turning under appropriate cutting data. Which series and grade should be cited when ordering? Order citing the Tiger·tec Gold series and grade WMP20G — VNMG160408-MM5 WMP20G by Walter Tools for clarity and correct part selection. Manufacturer: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen, Germany Protected trademarks and trade names are the property of their respective owners. Walter Tools and related product names are mentioned for explanation and comparison; there is no affiliation implied between Metav Werkzeuge and the trademark holders. The offered article is an original factory-new product of the manufacturer.
VNMG160408-MM5 WMP20S WMP20S Wendeplatten - Walter Tools
Take advantage of the combination of durable Tiger‑tec Silver coating, optimised MM5 chip control and a stable rhombic 35° geometry for trouble-free rostfreier Stahl turning; order the insert directly via Metav Werkzeuge or consult our specialists for tailored cutting data. VNMG160408-MM5 WMP20S turning insert, Tiger‑tec Silver, for rostfreier Stahl — Walter Tools VNMG160408-MM5 WMP20S is a negative‑rake, rhombic 35° turning insert designed for reliable machining of rostfreier Stahl under medium to robust cutting conditions Tiger‑tec Silver coated carbide grade WMP20S Optimised MM5 chipformer for stable chips Rhombic 35° VNMG geometry for versatility Suitable for rostfreier Stahl applications Longer tool life through advanced coating and material match The combination of Tiger‑tec Silver coating and the WMP20S grade delivers greater resistance to thermal and mechanical wear when machining rostfreier Stahl. The coating reduces built‑up edge tendency and improves heat management, which extends tool life and reduces tool change frequency. In practice, this means more consistent production runs and fewer interruptions on the shop floor. The insert’s coated carbide composition supports stable cutting under medium to robust conditions, providing predictable performance across a range of rostfreier Stahl alloys. Precise geometry for controlled chip formation and surface quality The rhombic 35° form with a 0° negative rake and a 0.8 mm nose radius balances strength and cutting precision. The MM5 chipbreaker is engineered to produce short, controllable chips when turning ductile, work‑hardening rostfreier Stahl, reducing the risk of entanglement and surface defects. A plate thickness corresponding to the "04" specification ensures rigidity in the insert pocket, while the VNMG style offers broad application coverage for longitudinal and profiling cuts. These geometry features translate into improved dimensional stability and repeatable surface finish. Process reliability and shop integration for productivity gains Designed for industrial turning operations, this insert supports consistent cycle times and easier process planning. The VNMG160408‑MM5 WMP20S insert fits standard VNMG toolholders and benefits shops that require uniform performance across multiple shifts. Because the grade and chipformer are matched to rostfreier Stahl behaviour, process windows are wider and more forgiving, helping to lower scrap rates. For manufacturers seeking predictable tool life and repeatable results, this insert contributes to a more efficient machining workflow without the need for frequent parameter redesign. Request tailored cutting data and availability from Metav Werkzeuge for Walter Tools Tiger‑tec Silver inserts to unlock reliable rostfreier Stahl turning performance — eMail info@metav-werkzeuge.com or call +49 2822 7131930 for direct assistance Technical data Article number: VNMG160408-MM5-WMP20S-WALTER SKU: VNMG160408-MM5-WMP20S-WALTER Product type: Drehwendeschneidplatte (turning indexable insert) Manufacturer: Walter Tools Series: Tiger‑tec Silver Grade: WMP20S Facts Size: 16 mm Thickness: 4 mm Corner radius: 0.8 mm Rake angle: 0° (negative) Plate shape: Rhombus 35° Chipformer: MM5 Special features Coating: Tiger‑tec Silver Material: Coated carbide (Hartmetall) Suitability: rostfreier Stahl Execution: G (geometry/style) ISO designation: VNMG160408‑MM5 WMP20S FAQ What materials is this insert suitable for? The VNMG160408‑MM5 WMP20S turning insert from Walter Tools is primarily intended for rostfreier Stahl and is specified for medium to robust cutting conditions. How does the MM5 chipbreaker improve machining? The MM5 chipformer provides controlled, short chip formation when turning rostfreier Stahl, improving chip evacuation and surface quality while reducing entanglement risks. Can the insert be used in standard VNMG toolholders? Yes, the VNMG160408‑MM5 WMP20S matches standard VNMG pockets; verify clamping compatibility with the chosen toolholder before production use. What is the benefit of the Tiger‑tec Silver coating? Tiger‑tec Silver coating on the WMP20S grade enhances wear resistance and thermal stability, resulting in longer tool life and more consistent cutting performance on rostfreier Stahl. Which operations suit this insert best? The insert is well suited to general turning tasks including longitudinal turning and light profiling on rostfreier Stahl where robust edge stability and chip control are required. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Protected trademarks and product names are the property of their respective owners. Brand names and protected product names are mentioned solely for explanatory purposes. There is no affiliation between our company and the named brands. The offered item is original, factory‑new merchandise of the manufacturer (Walter Tools).
VNMG160408-MM5 WSM10S WSM10S Wendeplatten - Walter Tools
Take advantage of the combination of a wear‑resistant Tiger‑tec Silver coating, a MM5 chipbreaker and a robust rhombic geometry for steady production on stainless steels and superalloys; order the insert directly via Metav Werkzeuge or request technical advice from their consultants. VNMG160408-MM5 WSM10S rhombic 35° turning insert — Walter Tools, Tiger‑tec Silver for stainless steels and superalloys The VNMG160408-MM5 WSM10S is a rhombic 35° negative‑rake turning insert designed for stable machining of stainless steels and heat‑resistant superalloys, offering reliable chip control and prolonged tool life. Tiger‑tec Silver coating for long tool life Suitable for stainless steel and superalloys Rhombic 35° geometry, 0.8 mm corner radius Negative 0° rake for stable cutting action MM5 chipbreaker for secure chip control Enhanced process reliability for demanding materials The coated carbide grade from the Tiger‑tec Silver series is engineered for secure chip formation and reduced flank wear when machining tough workpiece families. The combination of a wear‑resistant coating and a substrate formulated for heat resistance means sustained cutting performance under thermal and mechanical load. This translates into fewer tool changes, more predictable cycle times and a steadier production flow, which supports higher overall equipment productivity in component turning operations. Stable cutting edge for reproducible part quality The insert’s rhombic 35° geometry and 0.8 mm corner radius deliver a balance between edge strength and finishing capability. The 0° negative rake provides an inherently rigid cutting edge that resists chipping during interrupted cuts or when facing irregularities in the material. As a result, dimensional repeatability and surface finish are improved without sacrificing robustness, enabling production tolerances to be maintained with lower scrap rates and less rework. Effective chip control and machining economy Integrated MM5 chip control features are designed to produce short, controllable chips when turning alloys that tend to form long, stringy swarf. Better chip breakup enhances machine safety, reduces secondary handling, and minimises downtime caused by entangled chips. The cumulative effect is an improved cost‑per‑part profile: longer tool life and fewer process interruptions lead to lower tooling consumption and higher net throughput in demanding turning applications. Practical application notes and material compatibility This insert is suitable for ISO groups M and S, making it appropriate for stainless steels, nickel‑based superalloys and titanium alloys where thermal resistance and edge stability are required. The MM5 chipbreaker and the insert’s robust geometry make it particularly useful for medium to heavy roughing and mixed finishing operations. For specific cutting speeds, feeds and depth‑of‑cut ranges, consult Metav Werkzeuge’s application support to align the insert selection with machine capability and workpiece fixture constraints. For procurement or tailored machining advice on the Walter Tools VNMG160408-MM5 WSM10S, contact Metav Werkzeuge for application support and fast delivery. Technical data Article number: VNMG160408-MM5-WSM10S-WALTER Label: Drehwendeschneidplatte VNMG160408-MM5 WSM10S Walter Tools Product type: Turning insert (rhombic, negative) Series: Tiger‑tec Silver Grade / sort: WSM10S Designation: VNMG160408-MM5 WSM10S Manufacturer: Walter Tools SKU: VNMG160408-MM5-WSM10S-WALTER Data Geometry: Rhombus 35° Corner radius: 0.8 mm Relief / rake: 0° (negative) Insert size: 16 Thickness: 04 Tolerance class: M Special features Coating: Tiger‑tec Silver (coated carbide) Chipformer: MM5 Material suitability: S / M (superalloys, stainless steels) Application: Heavy and difficult‑to‑cut materials, depending on geometry Cutting edge characteristics: Robust for interrupted cuts and high temperatures FAQ What materials is this insert designed to machine? The Walter Tools VNMG160408‑MM5 WSM10S is intended for ISO group M and S workpieces — primarily stainless steels and heat‑resistant superalloys, where edge stability and heat resistance are critical. Which geometry and cutting edge does the insert use? The insert features a rhombic 35° geometry with a 0.8 mm corner radius and a 0° negative rake, delivering a rigid cutting edge for stable machining and repeatable part quality. How does the MM5 chipbreaker perform in practice? The MM5 chipbreaker is optimised for controllable chip formation on sticky or ductile alloys, reducing the risk of long swarf and promoting safer, more efficient machining cycles. What advantages does the Tiger‑tec Silver coating provide? The Tiger‑tec Silver coating improves wear resistance and thermal stability of the cutting edge, extending tool life and supporting consistent performance in demanding turning operations. Where can application data and cutting recommendations be obtained? Detailed cutting recommendations and application support are available from Metav Werkzeuge; they can advise on optimal parameters for the VNMG160408‑MM5 WSM10S based on machine and workpiece specifics. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen, Germany Protected trademarks and trade names are the property of their respective owners. Brand names and protected trade names are mentioned solely for explanation. There is no connection between our company and the named brands. The offered item is original factory‑new goods from the manufacturer.
VNMG160408-MM5 WSM20S WSM20S Wendeplatten - Walter Tools
Take advantage of the combination of Tiger·tec Silver coating and the MM5 chipbreaker for secure machining of stainless steel and heat‑resistant superalloys; the robust rhombic geometry and 0° negative rake support repeatable edge life. Order or request application advice via Metav Werkzeuge for smooth integration into production. VNMG160408-MM5 WSM20S — Turning insert with Tiger·tec Silver coating for stainless steel (Walter Tools) The VNMG160408-MM5 WSM20S is a rhombic 35° turning insert designed for heavy‑duty turning of stainless steel and heat‑resistant superalloys, offering a negative rake and an MM5 chipbreaker for controlled chip formation Tiger·tec Silver coated grade WSM20S Optimised MM5 chipbreaker Rhombus 35° form with 0° negative rake Corner radius 0.8 mm for stable edge life Reliable performance on difficult‑to‑cut alloys The WSM20S grade, implemented in the Tiger·tec Silver coating system, is developed for materials that challenge conventional grades. In practice this means improved resistance to thermal degradation and abrasion when cutting stainless steel and heat‑resistant superalloys (ISO groups M and S). The coating and substrate combination supports stable chip formation, reducing the risk of built‑up edge and enabling longer tool life under elevated cutting temperatures. This translates into predictable cycle times and fewer unplanned tool changes for production environments. Geometry engineered for edge security and surface finish A compact MM5 chipbreaker and the rhombus 35° form with 0° negative rake provide mechanical robustness where interrupted cuts and tough alloys are encountered. The corner radius 0.8 mm balances edge strength and surface finish: a larger radius increases resistance to edge chipping, while the rhombic geometry maintains access to narrow turning profiles. The coated carbide substrate adds wear resistance without sacrificing toughness, so operators benefit from consistent dimensional accuracy and surface quality across batch runs. Process security, integration and economic benefits As an indexable insert, this component reduces setup time and allows rapid index changes compared with brazed tips. The combination of grade and geometry supports productive machining strategies by lowering tool consumption and stabilising process windows. Backed by Walter Tools know‑how and the Tiger·tec Silver technology, the insert is suitable for demanding turning tasks where repeatability and part quality are priorities. Integration into standard toolholders is straightforward, aiding fast adoption on the shop floor and helping to protect throughput in serial production. Contact Metav Werkzeuge for detailed application recommendations and to arrange purchase of the VNMG160408-MM5 WSM20S; email info@metav-werkzeuge.com or call +49 2822 7131930 for expert advice and fast delivery options Technical Data Article number: VNMG160408-MM5-WSM20S-WALTER SKU: VNMG160408-MM5-WSM20S-WALTER Designation: VNMG160408-MM5 WSM20S Product type: Turning insert (indexable insert) Series: Tiger·tec Silver Grade: WSM20S Chipbreaker: MM5 Facts Inscribed circle: 16 mm Thickness: 4 mm (code 04) Corner radius: 0.8 mm Geometry angle: Rhombus 35° Relief / rake: 0° (negative) Tolerance class: M Special features Coating: Tiger·tec Silver (coated carbide) Suitability: S / M (heat‑resistant superalloys and stainless steels) Execution: G Plate form: Rhombus 35° Application focus: Heavy‑duty turning and difficult‑to‑cut alloys FAQ What materials is this insert designed for? The VNMG160408-MM5 WSM20S is formulated for machining stainless steel and heat‑resistant superalloys (ISO groups M and S), delivering thermal and wear resistance suited to these materials. How does the MM5 chipbreaker affect machining? The MM5 chipbreaker on this insert promotes controlled chip formation and evacuation, improving surface quality and reducing the chance of built‑up edge during turning operations with tough alloys. Is the geometry suitable for interrupted cuts? Yes, the rhombic 35° form with 0° negative rake and a 0.8 mm corner radius provides mechanical strength and edge stability, making it appropriate for interrupted turning and heavy engagement cutting. Can this insert be used with standard toolholders? The insert follows common VNMG specifications and is compatible with standard turning toolholders designed for this geometry; check holder code and clamping system for exact fit. What advantage does Tiger·tec Silver offer? Tiger·tec Silver coating enhances abrasion and thermal resistance on the coated carbide grade, supporting longer tool life and consistent performance on demanding materials. Walter Tools: Manufacturer/Responsible: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen Brand names and registered trademarks are the property of their respective owners. Trademarks and trade names are mentioned for explanatory purposes only. There is no affiliation between our company and the listed brands. The offered article is an original, factory‑new product of the manufacturer.
VNMG160408-MM5 WSM30S WSM30S Wendeplatten - Walter Tools
Take advantage of the Tiger·tec Silver coating and the MM5 chipbreaker to secure stable edge life and reliable chip control when machining rostfreier Stahl and heat-resistant alloys; the robust 0° negative rake and Rhombic 35° form ensure process security for demanding turning operations. Order or request availability through Metav Werkzeuge for fast delivery and application guidance. VNMG160408-MM5 WSM30S indexable turning insert – Rhombic 35°, 0.8 mm corner radius (Walter Tools) The VNMG160408-MM5 WSM30S is a rhombic 35° indexable turning insert optimised for machining rostfreier Stahl and heat-resistant superalloys in demanding production environments. Tiger·tec Silver coating for thermal resistance Designed for rostfreier Stahl and superalloys Rhombic 35° form with 0.8 mm corner radius 0° negative rake for edge stability Stable cutting performance for difficult-to-machine materials The combination of the WSM30S grade and Tiger·tec Silver coating provides enhanced resistance to thermal loading and wear, which translates into consistent cutting-edge life when turning rostfreier Stahl and similar alloys. The MM5 chipbreaker promotes controlled chip formation, reducing the risk of built-up edge and enabling predictable machining cycles. This results in fewer tool changes, improved machine uptime and measurable gains in process efficiency for serial production. Geometry that secures surface quality and repeatability The Rhombic 35° insert shape and 0.8 mm corner radius deliver a balance between strength and finish capability: the acute cutting angle supports positive cutting action for fine surface generation while the corner radius prevents premature edge failure under intermittent loads. The 0° negative rake increases edge robustness for medium to heavy interrupted cuts, providing repeatable results across batches and reducing scrap rates in mixed-production shops. Application guidance and operational benefits As a coated, solid carbide-based insert in the Tiger·tec Silver family, this grade is particularly suitable where thermal resilience and stable flank behaviour are required. Typical use cases include continuous and semi-continuous turning of rostfreier Stahl and heat-resistant superalloys where tool life and process security are prioritised. For optimised cycle times, match the insert geometry with appropriate nose radii and cutting parameters; Metav Werkzeuge can assist with tailored cutting data and application-specific recommendations for the VNMG160408-MM5 WSM30S insert. Contact Metav Werkzeuge for tailored cutting data, availability and order processing of Walter Tools Tiger·tec Silver WSM30S inserts Technical Data Article number: VNMG160408-MM5-WSM30S-WALTER SKU: VNMG160408-MM5-WSM30S-WALTER Product type: Drehwendeschneidplatte / indexable turning insert Brand: Walter Tools Grade: WSM30S Series: Tiger·tec Silver Designation: VNMG160408-MM5 WSM30S Execution: G Tolerance class: M Facts Clearance angle: 0° (negative) Corner radius: 0.8 Plate form: Rhombus 35° Plate size: 16 Plate thickness code: 04 Chipbreaker: MM5 Special features Coating technology: Tiger·tec Silver Material designation: S / M Suitable for: rostfreier Stahl Intended application: heavy-duty and heat-resistant alloy turning ISO groups: M (rostfreie Stähle), S (superalloys / titanium) Series properties: thermal resistance and edge stability FAQ What materials is this insert suitable for? The VNMG160408-MM5 WSM30S insert is formulated for machining rostfreier Stahl and heat-resistant superalloys, reflecting the S / M material designation of the Tiger·tec Silver family. How does the MM5 chipbreaker affect machining? The MM5 chipbreaker on the VNMG160408-MM5 supports controlled chip formation and reduced built-up edge, which helps to maintain consistent tool life and surface quality when machining demanding alloys. Is the 0° negative rake suitable for interrupted cuts? Yes, the 0° negative rake increases edge strength and is well suited to interrupted or heavier cuts, improving process security for batch and component work. What advantage does the Rhombic 35° form provide? The Rhombic 35° geometry offers a compromise between access and cutting action, enabling good surface finish while maintaining strength at the cutting edge for reliable repeatability. Can the VNMG160408-MM5 WSM30S be used for finishing operations? With its 0.8 mm corner radius and coated grade, the insert can achieve good surface finishes when paired with appropriate machining parameters; adjust feeds and speeds for the desired tolerance class. Manufacturer/Responsible: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen; Germany Protected trademarks and trade names are the property of their respective owners. Brand names and protected designations are mentioned for explanatory purposes only; there is no connection between our company and the named brands. The offered item is an original, factory-new product of the manufacturer. The Walter Tools brand is referenced in accordance with the product information.
Fragen zu diesen Produkten??
Mit mehr als 30 Jahren Erfahrung beraten wir Sie gerne persönlich.
Tel.: +49 2822 7131930
Mail: info@metav-werkzeuge.com