CNMG120408-MM5 WMP30G WMP30G Wendeplatten - Walter Tools
Take advantage of a proven cutting grade and robust geometry to keep turning operations reliable and productive; the combination of Tiger·tec Gold coating and the WMP30G grade supports stable chip formation and long edge life in stainless steel. Order the CNMG120408-MM5 WMP30G turning insert directly via Metav Werkzeuge or contact our consultants for application-specific advice. CNMG120408-MM5 WMP30G turning insert — Tiger·tec Gold grade for stainless steel, rhombic 80° by Walter Tools The CNMG120408-MM5 WMP30G is a coated carbide turning insert designed for medium to robust machining of stainless steel, combining an MM5 chipbreaker with a 0.8 mm corner radius for reliable chip control and edge stability. Tiger·tec Gold coated carbide grade WMP30G Optimised for stainless steel machining Rhombic 80° insert with 0.8 mm corner radius MM5 chipbreaker for stable chip control Reliable process performance for stainless steel turning The combination of the WMP30G grade and Tiger·tec Gold coating has been developed to manage the specific challenges of stainless steel: material toughness, tendency for built-up edge and elevated cutting temperatures. The coated carbide chemistry supports secure chip formation and maintains a stable cutting edge over repeated cycles, which translates into fewer interruptions and more consistent component quality. The insert’s negative relief (0°) increases edge strength under intermittent or interrupted cuts, helping to protect the cutting edge during medium to robust turning operations. Consistent surface finish and tool life through geometry and chip control The rhombic 80° shape and 0.8 mm corner radius offer a balanced compromise between strength and finish: the larger corner radius enhances edge robustness and contributes to stable tool life, while the precise geometry supports predictable contact conditions for improved surface integrity. The MM5 chipbreaker is tuned for stainless steel to produce short, manageable chips that reduce the risk of tangling and minimise secondary operations for chip handling. Together, geometry and chip control support higher uptime and more efficient machining cycles. Practical integration and application guidance for production use As an indexable solution, this insert fits established CNMG toolholders and can be rotated to present fresh cutting edges, reducing tooling costs per part. The coated carbide construction and MM5 chipbreaker make the insert particularly suitable for component manufacturing where repeatability and process security matter. For specific cutting data, toolholder compatibility and optimal feeds and speeds in stainless steel applications, Metav Werkzeuge’s advisory service can provide tailored recommendations based on workpiece dimensions and machine capability. For component makers seeking a robust solution for stainless steel turning, contact Metav Werkzeuge for technical guidance and prompt supply of Walter Tools CNMG120408-MM5 WMP30G inserts Technical Data Article number: CNMG120408-MM5-WMP30G-WALTER Name: Drehwendeschneidplatte CNMG120408-MM5 WMP30G Walter Tools SKU: CNMG120408-MM5-WMP30G-WALTER Series: Tiger-tec Gold Grade: WMP30G Execution: G Facts Insert shape: Rhombus 80° Size: 12 Thickness: 04 Corner radius: 0,8 mm Relief angle: 0° (negativ) Chipbreaker: MM5 Special features Coating: Tiger·tec Gold (coated carbide) Material suitability: stainless steel Cutting material class: beschichtetes Hartmetall Manufacturer: Walter Tools FAQ Which materials is this insert intended for? The CNMG120408-MM5 WMP30G insert is specified for stainless steel machining; the WMP30G grade supports secure chip formation and stable cutting edges when machining these alloys. What benefits does the MM5 chipbreaker provide? The MM5 chipbreaker on this Walter Tools insert creates short, controllable chips in stainless steel, improving chip evacuation and reducing the risk of chip-related interruptions. What are the key geometric features of the insert? The insert is a rhombic 80° form with a 0.8 mm corner radius and a 0° (negative) relief angle, designed to balance edge strength and surface finish in medium to robust turning tasks. Which series and coating does this grade belong to? This turning grade is part of the Tiger·tec Gold series and is supplied as a coated carbide insert under the WMP30G designation for enhanced wear resistance. Is the insert suited to interrupted cuts or heavier engagement? The 0° negative relief and robust corner radius make the insert resilient under intermittent loading and suitable for medium to robust cutting conditions; adjust cutting parameters according to the specific application and machine capability. Protected trademarks and trade names are the property of their respective owners and are mentioned for explanation only. There is no connection between our company and the named manufacturers. The offered item is an original, factory-new product of the manufacturer. Manufacturer/Responsible: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen
CNMG120408-MM5 WSM10S WSM10S Wendeplatten - Walter Tools
Take advantage of proven wear resistance and stable chip control for reliable turning of stainless steels and heat‑resistant alloys; the Tiger·tec Silver grade and MM5 chipbreaker combine to extend tool life and secure process stability. Order the insert directly via Metav Werkzeuge or consult our technical advisers for application‑specific recommendations. CNMG120408-MM5 WSM10S indexable turning insert — Tiger·tec Silver, Walter Tools The CNMG120408-MM5 WSM10S is a negative‑side, rhombic 80° indexable insert designed for robust turning in stainless steels and heat‑resistant superalloys, offering controlled chip formation and high thermal resistance. Tiger·tec Silver coating for heat resistance MM5 chipbreaker for consistent chip control Rhombic 80° form, 0.8 mm corner radius 0° negative free angle for robust turning Process security when machining stainless steels and superalloys The coated‑carbide grade WSM10S delivers a combination of thermal stability and edge integrity that supports predictable performance when machining challenging materials. Designed within the Tiger·tec Silver series, this grade is optimised for applications in stainless steels (ISO group M) and heat‑resistant superalloys or titanium (ISO group S). The material‑matched coating reduces built‑up edge and improves resistance to elevated cutting temperatures, which in turn lowers the frequency of tool changes and supports uninterrupted production cycles. Consistent chip control and surface quality Chip control is achieved through the MM5 chipbreaker geometry together with the Rhombus 80° plate form and a 0.8 mm corner radius. This combination produces short, controllable chips on interrupted cuts and continuous turning operations alike, reducing the risk of surface damage and stabilising cutting forces. The 0° negative free angle contributes to mechanical robustness, making the insert suitable for heavier cuts and applications where a secure tool edge is required. Extended tool life and predictable economy The Tiger·tec Silver technology focuses on wear resistance and edge stability to extend service life under demanding conditions. With optimised coating and substrate pairing, the insert offers a balance between toughness and hardness, which supports repeatable performance and predictable replacement intervals. The result is improved overall process economy through fewer tool interventions and steady component quality over longer machining campaigns. Practical application notes and compatibility The insert is supplied in the CNMG120408 format with the MM5 chipbreaker and is compatible with holders designed for rhombic 80° inserts. For stable results, select cutting parameters matched to the workpiece alloy and prioritise coolant or heat management strategies appropriate for stainless steels and superalloys. The insert’s specification supports a broad range of turning tasks from general finishing to moderate roughing, while custom cutting data can be provided on request by Metav Werkzeuge’s technical team. Contact Metav Werkzeuge for tailored application advice and to order Walter Tools CNMG120408-MM5 WSM10S inserts — eMail: info@metav-werkzeuge.com, Tel: +49 2822 7131930 Technical data Article number: CNMG120408-MM5-WSM10S-WALTER Label: Drehwendeschneidplatte CNMG120408-MM5 WSM10S Walter Tools Brand: Walter Tools Series: Tiger·tec Silver Grade: WSM10S Geometry: Rhombus 80° Core technical data Insert size: 12 mm Corner radius: 0.8 mm Thickness code: 04 Free angle: 0° (negative) Tolerance class: M Special features Chipbreaker: MM5 Coating: Tiger·tec Silver (coated carbide) Material suitability: stainless steels (M) Material suitability: heat‑resistant superalloys and titanium (S) Plate form: Rhombus 80° Execution: G FAQ What materials is this insert suitable for? The CNMG120408-MM5 WSM10S insert is formulated for stainless steels (ISO M) and heat‑resistant superalloys/titanium (ISO S), providing improved heat resistance and stable cutting edges in these groups. Which chipbreaker should be selected for general turning tasks? The MM5 chipbreaker integrated in this grade offers consistent chip control for a wide range of turning operations, suitable for both interrupted and continuous cuts. How does the 0.8 mm corner radius affect the cutting result? A 0.8 mm corner radius balances strength and edge definition, improving surface finish at lighter feeds while providing durability for heavier engagement compared with smaller radii. Is this insert suitable for roughing as well as finishing? Yes — the 0° negative free angle and robust grade make the insert appropriate for moderate roughing and finishing, depending on the selected cutting parameters and holder rigidity. What is the product reference for ordering? Order using SKU CNMG120408-MM5-WSM10S-WALTER, which identifies the CNMG120408 format with the WSM10S grade and MM5 chipbreaker from Walter Tools. Manufacturer/Responsible: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen; Germany Protected trademarks and trade names are the property of their respective owners. Brand names and protected trade names are mentioned solely for explanatory purposes and do not imply any affiliation with our company. The offered article is an original, brand‑new product from the manufacturer.
CNMG120408-MM5 WSM20S Wendeplatten - Walter Tools
Take advantage of high process security, stable chip formation and robust edge life to reduce downtime and increase throughput. The combination of Tiger·tec Silver coating and the WSM20S grade ensures reliable performance in demanding applications; order directly via Metav Werkzeuge or consult the technical team for application-specific advice. CNMG120408-MM5 WSM20S Rhombic 80° turning insert — Tiger·tec Silver for rostfreier Stahl and high‑temperature alloys (Walter Tools) CNMG120408-MM5 WSM20S is a negative‑rake, rhombic‑80° indexable turning insert optimised for demanding materials and stable chip control Tiger·tec Silver coating for process security Suited to rostfreier Stahl and heat‑resistant alloys Rhombic 80° CNMG geometry for versatile turning 0.8 mm corner radius with MM5 chipformer Stable chip formation and consistent edge life for higher productivity The coated indexable insert delivers repeatable cutting performance thanks to the Tiger·tec Silver coating and the WSM20S grade. These features improve thermal resistance and wear behaviour, which leads to more predictable tool life and fewer unscheduled tool changes. Stable chip formation reduces the risk of built‑up edge and improves surface integrity on subsequent passes. For production environments where uptime and consistency are priorities, the insert contributes directly to process reliability and reduced unit costs. Designed for rostfreier Stahl and high‑temperature alloys — explained The cutting material classification S / M indicates suitability for both heat‑resistant superalloys/titanium and rostfreier Stahl. Machining these groups places heavy thermal and mechanical loads on the cutting edge; the WSM20S grade is formulated to withstand such conditions. In practical terms, this means improved resistance to thermal softening and better retention of a sharp edge during interrupted or continuous cuts, which helps maintain dimensional accuracy and surface finish when working with difficult‑to‑machine components. Geometry and chip control that support versatile turning operations The rhombic 80° CNMG geometry provides a balanced approach between strength and accessibility, allowing effective external turning and light profiling. The MM5 chipformer plus a 0.8 mm corner radius supports secure chip breaking and reduces vibration in medium cuts. A negative rake with 0° free angle enhances edge robustness under tougher cutting conditions. These geometric choices translate into operational benefits: fewer insert changes, steady cutting forces and reliable performance across a range of cutting parameters. Practical advantages at the machine and on the shop floor Using this turning insert can reduce cycle times and rework: coating and grade reduce flank wear while chip control helps keep the work area cleaner, lowering downstream handling time. The insert’s tolerance class M and consistent lot characteristics support interchangeability and reproducible results across batches, simplifying tool management. When combined with a systematic cutting data approach and appropriate clamping, the insert supports both single‑piece and batch production with predictable outcomes. Contact Metav Werkzeuge for tailored recommendations on Walter Tools Tiger·tec Silver inserts and compatibility with specific machines and workpiece materials — eMail: info@metav-werkzeuge.com, Tel: +49 2822 7131930 Technical data SKU: CNMG120408-MM5-WSM20S-WALTER Description: Drehwendeschneidplatte CNMG120408-MM5 WSM20S Walter Tools Manufacturer: Walter Tools Series: Tiger·tec Silver Grade: WSM20S Chipformer: MM5 Execution: G Tolerance class: M Numbers / Core technical data Size: 12 Thickness: 04 Corner radius: 0.8 mm Free angle: 0° (negative) Plate form: Rhombus 80° Edge designation: CNMG120408-MM5 Special features / Materials & functions Coating: Tiger·tec Silver Grade type: coated cemented carbide Suitable for: rostfreier Stahl (M) Suitable for: heat‑resistant superalloys and titanium (S) Chip control: MM5 Series description: WSM20S — optimised for heavy‑duty and high‑temperature applications FAQ Which materials are best suited for this insert? The CNMG120408‑MM5 WSM20S insert is specified for rostfreier Stahl and heat‑resistant superalloys/titanium; the WSM20S grade and Tiger·tec Silver coating target the thermal and mechanical demands of these groups. What does the MM5 chipformer provide? The MM5 chipformer enables reliable chip breaking in medium cutting conditions, helping to maintain a stable process and reduce the risk of chip entanglement during operations with the CNMG geometry. Can the insert be used for interrupted cuts? Yes — the negative‑rake design and robust grade deliver enhanced edge strength, making the insert suitable for interrupted and mixed turning tasks where shock resistance is required. How does the Tiger·tec Silver coating affect tool life? The Tiger·tec Silver coating increases thermal stability and wear resistance, which typically leads to longer tool life and more consistent cutting performance under elevated temperatures. Is the corner radius of 0.8 mm suitable for finishing passes? A 0.8 mm corner radius offers a compromise between strength and finish; it is appropriate for light to medium finishing where improved edge life is desired without sacrificing surface quality. Manufacturer/Responsible: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen Protected trademarks and trade names are the property of their respective owners. Mention of brand names serves only for explanation and does not imply any affiliation between Metav Werkzeuge and the manufacturers. The offered item is an original, brand‑new product from the manufacturer.
CNMG120408-MM5 WSM30S MM5 Wendeplatten - Walter Tools
Take advantage of the high thermal resistance and edge stability of the WSM30S grade together with the proven Tiger‑tec Silver coating for consistent chip control and long tool life; order directly via Metav Werkzeuge or contact the consultants for application advice. CNMG120408-MM5 WSM30S – Rhombic 80° indexable turning insert by Walter Tools for rostfreier Stahl and heat‑resistant alloys The CNMG120408-MM5 WSM30S is a rhombic 80° indexable turning insert optimised for finish and medium roughing in rostfreier Stahl and S‑group superalloys, combining a robust chipbreaker and a wear‑resistant coating for stable cutting performance Tiger·tec Silver coating for high temperature resistance WSM30S grade optimised for rostfreier Stahl MM5 chipbreaker for stable chip control Rhombic 80° geometry for versatile profiles Boosted process stability through heat‑resistant coating and grade The combination of the Tiger·tec Silver coating and the WSM30S grade enhances resistance to thermal degradation and supports a predictable wear pattern. This means the insert maintains a stable cutting edge under prolonged contact with hot, sticky materials such as rostfreier Stahl and high‑temperature alloys. The result is fewer unscheduled tool changes and a more consistent surface finish, which directly improves machine uptime and reduces overall part cost. Efficient chip control and surface consistency for demanding materials Equipped with the MM5 chipbreaker and a rhombic 80° form, the insert promotes controlled chip formation and evacuation even under higher cutting forces. For applications where built‑up edge and poor chip flow are risks, the engineered chip geometry lowers the likelihood of rework. Operators gain a measurable improvement in production reliability and a repeatable part quality without extensive parameter experimentation. Geometry and dimensions tailored for versatile turning tasks The insert features a corner radius of 0.8 mm and a negative 0° clearance, providing a robust edge and secure seat in negative‑geometry toolholders. The size code corresponds to a 12 mm inscribed circle, with thickness code 04 for a compact but rigid profile. These dimensions make the component suitable for a wide range of external turning operations where rigidity and edge strength are priorities. Easy process integration and clear application scope Specified for machining rostfreier Stahl and S‑group materials, the insert simplifies grade selection for mixed‑material production environments. The negative geometry and proven coating technology reduce the sensitivity to thermal spikes, which is particularly valuable when running variable feed rates or interrupted cuts. Technical documentation and grade data support quick parameter selection and shorter set‑up times at the machine. For precision turning in rostfreier Stahl or superalloys, rely on the Walter Tools Tiger‑tec Silver grade WSM30S and contact Metav Werkzeuge for tailored cutting data and order handling Technical Data SKU: CNMG120408-MM5-WSM30S-WALTER Article designation: CNMG120408-MM5 ISO designation: CNMG120408-MM5 WSM30S Series: Tiger‑tec Silver Facts Shape: Rhombus 80° Size (inscribed circle): 12 Thickness code: 04 Corner radius: 0.8 mm Clearance angle: 0° (negative) Tolerance class: M Special features Grade: WSM30S Chipbreaker: MM5 Coating technology: Tiger·tec Silver (coated cemented carbide) Suitable workpiece groups: rostfreier Stahl (M), superalloys/titanium (S) Execution: G FAQ What materials is this insert designed for? The CNMG120408-MM5 WSM30S insert by Walter Tools is engineered for rostfreier Stahl and heat‑resistant superalloys (ISO groups M and S), offering enhanced edge stability and chip control for these material classes. Which chipbreaker does the insert feature and what is its benefit? The insert uses an MM5 chipbreaker, which promotes controlled chip formation and reliable evacuation, reducing the risk of entanglement and improving surface consistency in challenging cuts. How does the Tiger‑tec Silver coating help in production? Tiger‑tec Silver on the WSM30S grade increases thermal resistance and wear protection, enabling more stable tool life when machining high‑temperature materials and minimising unexpected tool wear. Is this a positive or negative geometry insert and why does that matter? This is a negative geometry insert with 0° clearance; the negative design provides a stronger cutting edge and greater clamping stability, making it suitable for heavier cuts and interrupted cutting conditions. Can the insert be used for both finishing and medium roughing? Yes, the combination of a 0.8 mm corner radius and the MM5 chipbreaker makes the insert versatile for finishing and medium roughing tasks in rostfreier Stahl and S‑group materials. Manufacturer: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Protected trademarks and trade names are the property of their respective owners. Brand names and registered trademarks are mentioned for clarification only. There is no affiliation between Metav Werkzeuge and the referenced manufacturers. The offered item is an original, factory‑new product of the respective manufacturer.
CNMG120408-MP3 WPP05G WPP05G Wendeplatten - Walter Tools
Taking advantage of the Tiger·tec Gold coating and the WPP05G grade, this turning insert delivers extended tool life and stable chip control for steel machining; order through Metav Werkzeuge or request tailored cutting data for immediate integration into production. CNMG120408-MP3 WPP05G turning insert — Tiger·tec Gold, MP3 chipbreaker (Walter Tools) The CNMG120408-MP3 WPP05G is a rhombic 80° turning insert designed for reliable steel machining in medium to heavy production environments. Tiger·tec Gold coating for extended tool life MP3 chipbreaker for stable chip control Rhombic 80° form for versatile turning 0.8 mm corner radius for robust surface finishes Optimised coating and grade for longer intervals between tool changes The insert is built on a coated carbide substrate and finished with Tiger·tec Gold, a high-performance coating that improves wear resistance and maintains edge stability under the thermal loads typical of steel turning. The WPP05G grade has been engineered to balance hardness and toughness, which results in reliable performance across a broad range of steel alloys. This combination reduces the frequency of tool changes and contributes to predictable component quality over longer production runs. Controlled chip formation for safer, more consistent machining Equipped with the MP3 chipbreaker, the geometry directs chip flow and minimises erratic swarf. The chipformer is calibrated for common steel machining parameters, enabling secure evacuation of chips at both moderate and higher cutting depths. As a result, machine uptime is improved and part rework due to chip interference is reduced, which supports safer workshop conditions and higher first-pass yield. Geometry that supports versatile set-up and repeatable results The rhombic 80° plate form and 0° negative clearance provide a robust cutting edge for a variety of turning operations, from roughing to finishing. The 0.8 mm corner radius offers a compromise between strength and surface quality, helping to avoid premature edge chipping while still achieving acceptable finishes on turned parts. The insert’s compact dimensions and standard designation facilitate straightforward toolholder selection and repeatable indexing. Application range and practical benefits for steel machining This insert is specified for ISO P materials and is particularly suitable where a combination of productivity and consistent component quality is required. The grade and chipbreaker pairing support efficient swarf control and stable cutting across unalloyed and alloyed steels. For production environments aiming to reduce process variability, the insert contributes to predictable tool life and easier process tuning, while the Walter Tools backing ensures availability and data support for process planning. Contact Metav Werkzeuge today for cutting-data sheets or to arrange a consultation on optimising machining parameters with Tiger·tec Gold inserts; eMail: info@metav-werkzeuge.com — Tel: +49 2822 7131930 Technical data Article number: CNMG120408-MP3-WPP05G-WALTER Designation: CNMG120408-MP3 ISO designation: CNMG120408-MP3 WPP05G Series: Tiger·tec Gold Grade: WPP05G Manufacturer: Walter Tools Product type: Turning insert Core specifications Inscribed circle / size: 12 mm Thickness: 4 mm Corner radius: 0.8 mm Clearance angle: 0° (negative) Tolerance class: M Materials & special features Coating: Tiger·tec Gold Chipbreaker: MP3 Insert form: Rhombus 80° Substrate: coated carbide Application: Steel (ISO P) Execution: G FAQ Which materials are suitable for this insert? The CNMG120408-MP3 WPP05G turning insert is specified for steel (ISO P) and is optimised for the typical heat and chip formation encountered when machining unalloyed and alloyed steels. What advantages does the Tiger·tec Gold coating provide? Tiger·tec Gold on the WPP05G grade increases wear resistance and edge stability, which extends tool life and supports consistent surface quality during longer production runs. How does the MP3 chipbreaker affect machining performance? The MP3 chipbreaker is designed to produce short, controllable chips under a range of cutting conditions, improving chip evacuation and reducing the risk of swarf-related interruptions when turning steel. Why choose a 0.8 mm corner radius? A 0.8 mm corner radius offers enhanced edge strength for robust cutting while still allowing good surface finish capability, making it a practical choice for mixed roughing and finishing cycles. How is the insert designated for ordering and identification? Identification is via the ISO designation CNMG120408-MP3 WPP05G and the SKU CNMG120408-MP3-WPP05G-WALTER, which ensures the correct grade, chipbreaker and form are supplied. Manufacturer/Responsible: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen‎ Protected trademarks and trade names are the property of their respective owners. Brand names and protected designations are mentioned for explanatory purposes only. There is no affiliation between our company and the mentioned brands. The offered article is an original, factory-new product of the manufacturer.
CNMG120408-MP3 WPP10G WPP10G Wendeplatten - Walter Tools
Take advantage of the Tiger‑tec Gold coating and the WPP10G grade for consistent, long tool life in steel turning; the MP3 chipbreaker and rhombic geometry ensure reliable chip control and surface quality. Order the insert directly via Metav Werkzeuge or ask the consultants for application support. CNMG120408‑MP3 WPP10G indexable turning insert — Rhombus 80°, MP3 chipbreaker (Walter Tools) The CNMG120408‑MP3 WPP10G is an indexable turning insert designed for machining steels (ISO P), combining a wear‑resistant coated grade with a medium‑duty chipbreaker for efficient, repeatable cutting performance. Tiger‑tec Gold coating for extended tool life Designed for ISO P (steel) machining Rhombus 80° shape for versatile turning 0.8 mm nose radius for balanced finish and strength Extended tool life through advanced coating and grade The combination of the Tiger‑tec Gold coating and the WPP10G grade delivers enhanced wear resistance and stable cutting-edge behaviour when machining steels. As a coated carbide solution, the insert reduces flank and crater wear under typical steel cutting temperatures, which contributes to longer tool life and fewer indexings. The result is a measurable productivity gain in batch and continuous operations, while maintaining predictable tool-change intervals. Reliable chip control and improved surface quality Equipped with the MP3 chipbreaker, the insert focuses on medium to heavier turning tasks, shaping chips to evacuate reliably under a wide range of feeds and depths of cut. The combination of the chipbreaker design and a 0.8 mm nose radius helps to balance cutting forces and surface finish, producing consistent component geometry and reducing the need for downstream finishing operations. This stability supports tighter process tolerances and fewer rejects. Robust geometry for demanding turning tasks The Rhombus 80° form provides good access for a variety of turning applications, offering both clearance and strength for interrupted or continuous cuts. The insert’s 0° rake (negative geometry) contributes to edge robustness, making it suitable for tougher engagement conditions. The nominal plate thickness and M tolerance class ensure repeatable seating and accurate positioning in standard toolholders, which is essential for consistent production. Application guidance for process security Classified for ISO P materials, the insert is intended primarily for unalloyed and alloyed steel machining where thermal and chip‑formation behaviour is typical for steels. Use the insert where a balance of wear resistance and toughness is required—typical tasks include general turning, light profiling and semi‑finishing operations. For tailored recommendations on cutting data or holder selection, Metav Werkzeuge can provide application‑specific guidance to integrate the insert into existing processes. Contact Metav Werkzeuge for tailored application advice and to secure the Walter Tools Tiger‑tec Gold WPP10G indexable insert for steel turning; email info@metav-werkzeuge.com or call +49 2822 7131930 Technical data SKU: CNMG120408-MP3-WPP10G-WALTER Facts Inscribed circle: 12 Edge radius: 0.8 Clearance / rake: 0° (negativ) Tolerance class: M Plate thickness: 04 Special features Grade: WPP10G Series: Tiger-tec Gold Chipbreaker: MP3 Shape: Rhombus 80° Material application: P (steel) Manufacturer: Walter Tools FAQ Which materials is this insert suitable for? The CNMG120408‑MP3 WPP10G insert is specified for ISO P materials and is intended primarily for machining unalloyed and alloyed steel. What advantages does the Tiger‑tec Gold grade provide? The Tiger‑tec Gold coating on the WPP10G grade improves wear resistance and thermal stability, extending tool life and ensuring consistent cutting performance for steel applications. What cutting tasks is the MP3 chipbreaker best for? The MP3 chipbreaker is optimised for medium to heavier turning cuts, delivering stable chip formation and evacuation under varying feeds and depths of cut. How does the insert geometry affect process reliability? The Rhombus 80° shape and negative 0° rake support robust edge strength and flexible access to the workpiece, aiding interrupted cuts and maintaining repeatable positioning in standard holders. Manufacturer: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen; Germany Geschützte Markenzeichen und Warenbezeichnungen liegen im Recht ihrer jeweiligen Eigentümer. Markennamen und geschützte Warenzeichen werden ausschließlich zu Erklärungszwecken genannt. Es besteht keinerlei Verbindung zwischen unserem Unternehmen und den genannten Marken. Es handelt sich bei dem angebotenen Artikel um originale fabrikneue Waren des Herstellers.
CNMG120408-MP3 WPP20G WPP20G Wendeplatten - Walter Tools
Take advantage of the combination of high process stability, long tool life and optimised chip control for efficient steel turning operations; order the insert directly via Metav Werkzeuge or consult our specialists for application advice. CNMG120408-MP3 WPP20G indexable turning insert, Tiger‑tec Gold coating, for steel — Walter Tools A CNMG120408-MP3 WPP20G indexable turning insert designed for robust material removal in steel machining, combining a Tiger‑tec Gold coating with an MP3 chipbreaker for consistent chip formation. Tiger‑tec Gold coating for extended life Optimised MP3 chip control for reliable machining Suitable for a wide range of steel grades Rhombus 80° shape with 0.8 mm corner radius Increased productivity through optimised coating and grade The Tiger‑tec Gold coating together with the WPP20G grade provides a wear‑resistant cutting edge that supports sustained production runs on steel. This combination reduces flank wear and helps maintain dimensional stability over extended cycles, which translates directly into fewer tool changes and higher machine uptime. The coated carbide substrate resists thermal and abrasive damage typical for P‑group machining, so cycle times can be more consistent and predictable. Reliable chip control and surface quality Equipped with an MP3 chipbreaker, this insert ensures reliable chip formation during medium to heavy turning. The chipformer geometry prevents entanglement and supports effective evacuation, reducing the risk of rework and machine interruptions. Stable chip flow also contributes to a consistent workpiece finish, making it easier to achieve repeatable tolerances and minimise secondary operations. Application clarity and compatibility in workshop use The Rhombus 80° profile and 0.8 mm corner radius combine to offer a balance between edge strength and fine detail capability, suitable for a broad spectrum of steel grades as defined for P‑group materials. The insert’s 0° clearance (negative) configuration provides a secure cutting edge under heavy loads and supports reliable, repeatable turning. Selection of this insert is appropriate where a productive, general‑purpose solution for steel is required, with proven performance across diverse machining tasks. Contact Metav Werkzeuge now for application recommendations on Walter Tools Tiger‑tec Gold inserts and secure reliable machining performance for demanding steel turning tasks Technical data Article number: CNMG120408-MP3-WPP20G-WALTER Designation: CNMG120408-MP3 WPP20G Series: Tiger‑tec Gold Facts Insert size: 12 mm Corner radius: 0.8 mm Thickness code: 04 Clearance angle: 0° (negative) Tolerance class: M Special features Coating: Tiger‑tec Gold Grade: WPP20G Chipbreaker: MP3 Shape: Rhombus 80° Material application: Steel (P) Manufacturer: Walter Tools Suitable for general turning applications on steel FAQ What materials is this insert optimised for? The CNMG120408-MP3 WPP20G insert from Walter Tools is optimised for machining steel (ISO group P), covering a wide range of unalloyed and alloyed steels. How does the MP3 chipbreaker affect machining? The MP3 chipbreaker on the Walter Tools insert promotes consistent chip formation and evacuation, which reduces interruptions and helps maintain a steady surface quality. Is the Tiger‑tec Gold coating suitable for high temperatures? Yes, the Tiger‑tec Gold coating on this Walter Tools grade improves thermal resistance and wear protection during typical steel turning operations. What advantages does the Rhombus 80° shape provide? The Rhombus 80° geometry offers flexible approach angles for external turning tasks and supports secure clamping with good access to a range of contours. Can this insert be used for heavy roughing? The combination of WPP20G grade, robust chip control and a negative clearance makes the insert suitable for productive roughing under appropriate cutting parameters. Manufacturer: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen, Germany Protected trademarks and trade names are the property of their respective owners. Brand names and registered trademarks are mentioned for explanatory purposes only. There is no affiliation between our company and the brands referenced. The offered item is an original, factory‑new product of the manufacturer.
CNMG120408-MP3 WPP30G WPP30G Wendeplatten - Walter Tools
Benefit from the combination of high wear resistance and controlled chip formation for consistent, productive steel turning; the Tiger‑tec Gold coated grade and MP3 chipbreaker ensure reliable performance. Order the insert directly via Metav Werkzeuge or ask the consultants for application advice. CNMG120408-MP3 WPP30G Turning Indexable Insert — Tiger‑tec Gold for steel (Rhombic 80°, 0.8 mm) by Walter Tools The CNMG120408-MP3 WPP30G is a rhombic 80° turning indexable insert with Tiger‑tec Gold coating, optimised for steel machining and designed for dependable chip control in medium to heavy turning operations Tiger‑tec Gold coated carbide WPP30G MP3 chipbreaker for consistent chips Rhombic 80° geometry, 0.8 mm corner radius Optimised for steel machining (ISO P) Durable cutting performance through Tiger‑tec Gold coating A coated carbide grade such as Tiger‑tec Gold extends the service life of the insert by improving wear resistance and thermal stability during steel turning. The WPP30G grade is designed for the heat and chip characteristics typical of ISO P materials, which translates into fewer tool changes and longer productive tool life. For production environments where cycle time and predictable performance matter, this coating technology helps maintain edge integrity and reduces the frequency of interruptions for tool replacement. Controlled chip formation for safer, cleaner turning The MP3 chipbreaker is engineered to deliver fragmented, controllable chips when machining steel, lowering the risk of long swarf and improving operator safety. Combined with the rhombic 80° geometry and a 0.8 mm corner radius, the insert produces stable cutting forces and improved surface finishes under varying cutting conditions. This combination reduces vibration and supports consistent part quality, especially in operations that require repeatable dimensional accuracy. Application-focused design for steel machining (ISO P) Specifically targeted at steel applications, the grade and geometry are tailored for both unalloyed and alloyed steels commonly encountered in workshop and production settings. The material designation for this insert indicates suitability for ISO P groups, which means the cutting edge and chip control have been optimised for the thermal loads and deformation behaviour typical of steel. The outcome is reliable metal removal rates and consistent surface integrity across batches. Practical integration and handling in the production cell The insert designation breaks down into a familiar CNMG form factor with an inscribed circle size code of 12 and a plate thickness code of 04, making it compatible with a wide range of standard CNMG toolholders. The 0° negative rake specification supports stable cutting in heavier passes, while the tolerance class M ensures dimensional conformity for repeatable clamping and indexation. For additional technical data or application-specific recommendations, Metav Werkzeuge can provide processing parameters and cutting trials tailored to the workpiece material and machine conditions. Contact Metav Werkzeuge for tailored application advice and availability of Walter Tools CNMG120408-MP3 WPP30G inserts, or request cutting parameter recommendations from the Metav team. Technical data SKU: CNMG120408-MP3-WPP30G-WALTER Designation: CNMG120408-MP3 WPP30G Type: Turning indexable insert Manufacturer: Walter Tools Facts Plate size: 12 Plate thickness: 04 Corner radius: 0.8 mm Free angle: 0° (negative) Tolerance class: M Special features Coating: Tiger‑tec Gold Grade: WPP30G (coated carbide) Chipbreaker: MP3 Plate form: Rhombus 80° Suitable for: Steel (ISO P) Execution: G FAQ What materials is this insert suitable for? The CNMG120408-MP3 WPP30G insert is formulated for machining steel (ISO P); the Walter Tools grade WPP30G is optimised for common unalloyed and alloyed steels. How does the MP3 chipbreaker improve machining? The MP3 chipbreaker produces short, controlled chips in steel turning, aiding chip evacuation and reducing the chance of long swarf, which improves safety and surface quality. What does the 0° negative rake mean for cutting? A 0° negative rake provides a robust cutting edge that withstands higher cutting forces, offering stability during heavier cuts and enhancing edge life for demanding turning operations. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Protected trademarks and trade names are the property of their respective owners. Brand names and protected trade names are mentioned solely for explanatory purposes. There is no connection between our company and the mentioned brands. The offered article is original, factory-new goods of the manufacturer.
CNMG120408-MP5 WKK10S Wendeplatten - Walter Tools
Take advantage of the proven combination of high wear resistance and stable chip control to increase turning productivity on abrasive cast iron. Benefit from a robust 0° negative rake and the Tiger·tec Silver coated grade for longer tool life and consistent surface quality — order via Metav Werkzeuge or consult the team for application-specific cutting data. CNMG120408-MP5 WKK10S — Turning indexable insert, Tiger·tec Silver, for cast iron (Walter Tools) CNMG120408-MP5 WKK10S is a rhombic 80° indexable turning insert designed for efficient machining of cast iron components in industrial turning applications Tiger·tec Silver coating for high wear resistance Optimised for abrasive cast iron machining MP5 chipbreaker for short, controllable chips Rhombic 80° shape with 0.8 mm corner radius Maximise metal removal rates with a grade tuned to cast iron The combination of the Tiger·tec Silver coating and the WKK10S grade provides a clear productivity advantage when machining cast iron. The coating reduces abrasive wear from hard graphite phases and maintains a consistent cutting edge over extended cycles, which translates into fewer insert changes and reduced spindle downtime. In practice, the MP5 chipbreaker promotes short, predictable chips that ease evacuation and reduce the risk of workpiece damage, supporting higher feed rates without compromising surface finish. Robust geometry for interrupted cuts and heavy engagement The rhombic 80° form and the 0° (negative) rake angle create a mechanically strong cutting edge suited to heavy engagement and interrupted cuts often encountered in roughing operations. The 0.8 mm corner radius balances strength and edge life while still allowing acceptable surface quality in semi-finish passes. These geometric choices mean the insert tolerates higher radial depths of cut and provides repeatable machining behaviour, improving process reliability in batch and single-piece production. Consistent performance and simplified process planning As a coated carbide turning solution, the insert supports a wide range of cast-iron grades identified under ISO group K. The coating and substrate pairing deliver predictable wear progression, making tool life estimation and process planning more straightforward. For machining centres requiring reproducible outcomes, the insert’s tolerance class M and standardised form simplify toolholder selection and tool management. For specification queries or tailored machining advice, Metav Werkzeuge supplies cutting data and recommendations to align insert choice with cycle-time and surface-quality targets. Contact Metav Werkzeuge for application-specific cutting data and fast, reliable supply of Tiger·tec Silver inserts from Walter Tools. Technical data Article number / SKU: CNMG120408-MP5-WKK10S-WALTER Designation: CNMG120408-MP5 WKK10S Manufacturer: Walter Tools Product type: Turning indexable insert Core specifications Insert size: 12 mm Thickness designation: 04 Corner radius: 0.8 mm Rake / clearance: 0° (negative) Shape: Rhombus 80° Tolerance class: M Special features Coating: Tiger·tec Silver Grade: WKK10S (coated carbide) Chipbreaker: MP5 Application: Cast iron (ISO group K) Edge type / execution: G FAQ What materials is this insert designed for? The CNMG120408-MP5 WKK10S is designed primarily for cast iron applications (ISO group K) and is tuned to handle abrasive graphite-rich workpieces. How does the Tiger·tec Silver coating improve performance? The Tiger·tec Silver coating reduces abrasive wear on the carbide substrate, extending insert life and maintaining cutting-edge stability during extended turning cycles. What chip control can be expected with the MP5 chipbreaker? The MP5 chipbreaker produces short, controllable chips ideal for safe evacuation in turning operations, helping to protect the workpiece and tooling. Is this insert suitable for roughing and finishing? Yes — the 0° (negative) rake and 0.8 mm corner radius provide robust edge strength for roughing, while the geometry still permits acceptable surface quality in semi-finishing passes. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen, Germany The Walter AG (brand appearance: Walter Tools) with headquarters in Tübingen is among the leading manufacturers of precision tools for metalworking and is part of the Sandvik Group. Protected trademarks and trade names are the property of their respective owners. Brand names and trademarks are mentioned for explanatory purposes only. There is no affiliation between our company and the named brands. The offered item is original factory-new merchandise from the manufacturer.
CNMG120408-MP5 WPP05G Wendeplatten - Walter Tools
Take advantage of Tiger·tec Gold performance and the MP5 chipbreaker for consistent chip control and extended tool life; the rhombic geometry and 0.8 mm corner radius deliver a robust compromise between edge strength and finish. Order directly via Metav Werkzeuge or consult our specialists for application advice. CNMG120408-MP5 WPP05G turning insert — Tiger·tec Gold coated, for steel | Walter Tools CNMG120408-MP5 WPP05G is a rhombic 80° turning insert engineered for reliable steel machining in general turning applications Tiger·tec Gold coating for longer tool life MP5 chipbreaker for controlled chip formation Rhombic 80° geometry for versatile turning 0.8 mm corner radius for balanced strength Maximise uptime with consistent cutting performance The CNMG120408-MP5 WPP05G indexable insert combines a Tiger·tec Gold surface treatment with a coated carbide substrate to provide high resistance to wear while maintaining toughness for interrupted cuts. The MP5 chipbreaker promotes predictable chip formation across typical steel grades, reducing rework and machine downtime. Designed for industrial turning, this tool supports repeatable processes and contributes to a steady production flow through improved tool life and stable edge behaviour. Better surface quality and dependable chip control Thanks to the rhombic 80° geometry and a 0° negative rake, the insert offers an effective balance between cutting edge strength and surface finish. The MP5 geometry is optimised for common steel machining tasks, enabling controlled chips that evacuate reliably and reduce the risk of built-up edge. These characteristics translate into fewer interruptions, more consistent part quality and a lower frequency of insert changes during batch production. Robust design for adaptable workshop use With a 0.8 mm corner radius and a compact plate size, this turning insert is suitable for a wide range of turning operations where a compromise between edge robustness and fine finishing is required. The coated carbide grade provides a combination of wear resistance and toughness, making the insert appropriate for standard and moderately demanding steel machining tasks. Integration into existing toolholders is straightforward thanks to the CNMG form factor and standard mounting dimensions. Practical benefits for production planning Using this Walter Tools insert supports predictable tooling cycles and easier inventory planning: the proven Tiger·tec Gold coating increases interval lengths between tool changes, while the MP5 chip control simplifies swarf handling. For shops prioritising process reliability and repeatable part quality, the insert reduces process variance and aids compliance with production schedules, especially in high-volume turning environments. Choose Walter Tools' Tiger·tec Gold CNMG120408-MP5 WPP05G for greater process reliability and contact Metav Werkzeuge at info@metav-werkzeuge.com or +49 2822 7131930 for detailed application guidance Technical data Article number: CNMG120408-MP5-WPP05G-WALTER Designation: CNMG120408-MP5 WPP05G Manufacturer: Walter Tools Product type: turning insert Series: Tiger·tec Gold Facts Insert size: 12 mm Thickness: 4.0 mm Corner radius: 0.8 mm Relief angle: 0° (negative) Tolerance class: M Special features Coating: Tiger·tec Gold (coated carbide) Chipbreaker: MP5 Geometry: Rhombic 80° Sort: WPP05G Execution: G Suitable for: steel FAQ What materials is this insert suitable for? The CNMG120408-MP5 WPP05G from Walter Tools is specified for machining steel and is optimised for the thermal and chip-formation characteristics typical of steel grades. How does the MP5 chipbreaker affect machining? The MP5 chipbreaker on the CNMG120408-MP5 WPP05G promotes controlled chips and improves swarf evacuation, supporting stable cutting conditions and consistent surface quality. What benefits does the Tiger·tec Gold coating provide? Tiger·tec Gold on this Walter Tools insert increases wear resistance while maintaining toughness, which extends tool life and supports higher process reliability in turning operations. Hersteller: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Protected trademarks and trade names mentioned are the property of their respective owners. Brand names and protected trademarks are used solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The offered item is original, factory-new goods from the manufacturer (Walter Tools).
CNMG120408-MP5 WPP10G Wendeplatten - Walter Tools
Take advantage of the Tiger·tec Gold coating and the MP5 chipbreaker for consistent chip control and extended tool life; the CNMG120408-MP5 WPP10G offers a stable 0.8 mm nose radius and rhombic 80° geometry for reliable finishing operations. Order via Metav Werkzeuge or consult our specialists for application advice. CNMG120408-MP5 WPP10G — indexable turning insert for steel by Walter Tools CNMG120408-MP5 WPP10G is a negative‑lead, rhombic 80° turning insert designed for productive steel machining in serial production. Tiger·tec Gold coating for extended tool life MP5 chipbreaker for controlled chip formation 0.8 mm nose radius for stable finishing Rhombic 80° insert, negative 0° lead angle High productivity through robust coating and geometry The combination of the Tiger·tec Gold coating and a purpose‑designed insert geometry increases process stability and wear resistance. Through a hard, wear‑resistant surface layer, the grade reduces flank wear and allows longer uninterrupted cutting times, which results in fewer tool changes and higher machine utilisation. This contributes directly to improved throughput in turning operations on steel and lowers unit production cost without compromising repeatability. Predictable chip control and surface quality Equipped with the MP5 chipbreaker, this insert ensures reliable chip formation across common steel grades, improving evacuation and reducing risk of re-cutting. The controlled chip flow leads to consistent surface finish and decreases downtime caused by manual chip clearing. For customers requiring reproducible part quality, the geometry supports steady cutting forces and predictable tool behaviour in finishing and medium‑depth turning. Application range and material suitability The insert is specified for machining steel (ISO group P) and is optimised for typical thermal and metallurgical conditions encountered when turning unalloyed and alloyed steels. The 0.8 mm nose radius balances edge strength and detail reproduction, making the insert suitable for both light finishing cuts and moderate roughing where dimensional stability is required. The negative 0° lead angle improves edge strength under interrupted cuts and heavy engagement. Integration into production and handling benefits As a standard CNMG‑format insert, it integrates easily into common toolholders and turret systems, simplifying inventory and tool change procedures. The robust tolerance class and consistent grade properties support reliable indexation and repeatable clamping, contributing to lower scrap rates and predictable maintenance intervals. Components benefit from fewer process variances and a smoother workflow on the shop floor. Contact Metav Werkzeuge for tailored cutting data and application support for Walter Tools turning inserts and to discuss batch availability Technical Data Article number: CNMG120408-MP5-WPP10G-WALTER Designation: CNMG120408-MP5 WPP10G Product type: Drehwendeschneidplatte / indexable turning insert Manufacturer: Walter Tools Core data Insert size: 12 mm Thickness: 4 mm Nose radius: 0.8 mm Lead angle: 0° (negative) Insert shape: Rhombic 80° Tolerance class: M Special features Series: Tiger‑tec Gold Grade: WPP10G Chipbreaker: MP5 Execution: G Material group: P (steel) ISO designation: CNMG120408-MP5 WPP10G FAQ What materials is this insert recommended for? The CNMG120408‑MP5 WPP10G is specified for ISO group P — steel — and the grade and chipbreaker are optimised for a broad range of unalloyed and alloyed steels. How does the Tiger·tec Gold coating benefit production? The Tiger·tec Gold coating increases wear resistance and heat protection, extending tool life and enabling longer cutting times for the CNMG120408‑MP5 WPP10G. Which chipbreaker should be selected for mixed finishing and medium roughing? The MP5 chipbreaker integrated in this insert delivers controlled chip formation suitable for finishing and medium roughing in steel applications. Is the 0.8 mm nose radius suitable for fine finishing? Yes, the 0.8 mm radius on the insert offers a balance between edge strength and surface definition, making it appropriate for consistent finishing results. Manufacturer/Responsible: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen, Germany Protected trademarks and trade names are the property of their respective owners. Mention of brand names and registered trademarks is for explanatory purposes only and does not imply any affiliation or endorsement by the trademark owners. There is no connection between our company and the named manufacturers. The offered article is an original, factory‑new product of the manufacturer.
CNMG120408-MP5 WPP20G Wendeplatten - Walter Tools
Take advantage of the combination of long tool life, reliable chip control and versatile steel performance to maintain a steady production rhythm; order the inserts directly via Metav Werkzeuge or consult our technical advisors for cutting data and process recommendations. CNMG120408-MP5 WPP20G — Drehwendeschneidplatte (for steel) by Walter Tools, Tiger·tec Gold coating, MP5 chipbreaker A CNMG120408-MP5 WPP20G rhombic 80° turning insert designed for efficient steel machining, offering coated carbide performance and a stable cutting geometry for general turning applications Tiger·tec Gold coating for long tool life Optimised MP5 chipbreaker for controlled chips Rhombic 80° geometry for stable cuts 0.8 mm corner radius for robust edges Consistent wear resistance for demanding steel operations The combination of the Tiger·tec Gold coating and the WPP20G grade delivers a marked improvement in wear resistance for steel applications. Coated carbide technology provides a protective layer that reduces abrasive wear and maintains a sharp cutting edge, which translates into extended tool life and fewer insert changes. For operations that generate significant cutting heat, this coating helps to stabilise edge condition and supports repeatable machining results. As a consequence, cycle times remain predictable and tool costs per component are reduced while maintaining component tolerances. Reliable chip control and geometry that stabilises cutting forces The integrated MP5 chipbreaker and the Rhombic 80° shape work together to control chip formation and evacuate swarf efficiently. The chipbreaker is engineered to break and curl chips under a wide range of feeds and depths of cut, reducing the risk of entanglement and improving surface quality. The 0° negative rake setting enhances edge strength and contributes to process stability in medium- to heavy-duty cutting. A 0.8 mm corner radius offers robustness at the cutting edge, improving resistance to edge chipping and providing a consistent finish on the machined surface. Application advantages and process reliability in steel turning Specifically developed for the machining of steels (ISO group P), this indexable insert suits both unalloyed and alloyed steel grades commonly encountered in production workshops. The grade’s balance between wear resistance and toughness supports versatile use—short-run turning, medium-batch production and general finishing operations. The result is improved process reliability and better reproducibility from one workpiece to the next. For manufacturers seeking predictable outcomes and reduced downtime, the insert’s combination of geometry and coating offers a practical route to enhanced productivity and fewer interruptions for tool change. Contact Metav Werkzeuge today for tailored cutting parameters and to secure the CNMG120408-MP5 WPP20G inserts for steel machining, or request personalised application advice from our consultants. Technical Data Article number: CNMG120408-MP5-WPP20G-WALTER Designation: CNMG120408-MP5 WPP20G Manufacturer: Walter Tools Series: Tiger·tec Gold Type: Turning indexable insert Facts Corner radius: 0.8 mm Insert size/length: 12 mm Thickness: 4.0 mm Geometry: Rhombic 80° Cutting edge: 0° (negative) Tolerance class: M Special features Coating: Tiger·tec Gold (coated carbide) Grade: WPP20G, optimised for steel (ISO P) Chipbreaker: MP5 Application: turning of unalloyed and alloyed steels Robust corner radius for improved edge stability FAQ What materials is this insert intended for? The CNMG120408-MP5 WPP20G insert is specified for machining steels (ISO group P), covering both unalloyed and alloyed steel grades. How does the MP5 chipbreaker improve machining? The MP5 chipbreaker is designed to produce short, controllable chips across a range of feeds, improving swarf evacuation and surface finish while reducing the risk of chip-related issues. Is the grade suitable for finishing and medium cutting? Yes; the WPP20G grade balances wear resistance and toughness, making it suitable for finishing and medium cutting operations in steel. What advantages does the Tiger·tec Gold coating provide? The Tiger·tec Gold coating enhances wear resistance and thermal stability, extending tool life and supporting consistent edge condition during prolonged cutting. Can the insert handle interrupted cuts or hard conditions? The 0.8 mm corner radius and negative rake geometry contribute to edge strength and robustness, increasing resistance to chipping under interrupted or demanding conditions. Manufacturer: Walter Tools (part of Sandvik Group); AB Sandvik Coromant, Mossvägen 10, 811 34 Sandviken, Sweden; support.coromant@sandvik.com Protected trademarks and trade names remain the property of their respective owners. Brand names and registered trademarks are mentioned for explanatory purposes only. There is no connection between our company and the mentioned brands. The offered item is an original, brand-new product from the manufacturer.
CNMG120408-MP5 WPP30G WPP30G Wendeplatten - Walter Tools
Take advantage of the Tiger·tec Gold coating combined with the MP5 chipbreaker and a 0.8 mm nose radius to ensure stable chip formation and consistent surface quality; order this turning insert via Metav Werkzeuge or contact the technical consultants for application advice. CNMG120408-MP5 WPP30G — Indexable turning insert, Tiger·tec Gold coating for steel (Walter Tools) The CNMG120408-MP5 WPP30G is a rhombic 80° indexable insert engineered for efficient turning of steel components in production and jobbing environments. Tiger·tec Gold coated for high productivity MP5 chipbreaker for reliable chip control Rhombic 80° geometry for flexible turning 0.8 mm nose radius for consistent surface finish Optimised productivity and process security with coated carbide The combination of the Tiger·tec Gold coating and the coated carbide substrate provides a reliable balance between wear resistance and toughness, which leads to longer tool life under typical steel cutting conditions. This geometry and grade are specifically designed to manage the heat and chip formation that occur when machining steel; the result is improved cycle times and fewer interruptions for tool changes. The rhombic 80° form allows adaptable entry and exit angles in turning operations, while the MP5 chipbreaker optimises chip flow for automated and manual setups. Such characteristics contribute directly to stable machining behaviour and predictable performance. Consistent surface finish and secure chip control A 0.8 mm nose radius combined with the MP5 chipbreaker delivers a balance between edge strength and surface integrity. The moderate radius produces reliable component finishes without compromising the cutting edge under interrupted cuts or heavier feed rates. At the same time, the chip geometry promoted by the chipbreaker reduces the risk of entanglement and improves evacuation in both conventional and high-feed turning. For operations where repeatability and surface quality matter, the described insert minimises rework and supports consistent part acceptance criteria. Versatility for steel applications and straightforward tool management Classified for steel (ISO group P), this grade is intended for a broad range of steels from general-purpose to tougher, wear-prone materials. The insert’s tolerance class M and robust grade designation support repeatable indexing and predictable tool life across batch production. The rhombic 80° shape and standard size facilitate integration into common toolholders, simplifying inventory and tool change procedures. Together, these attributes reduce tooling complexity on the shop floor while maintaining a high level of process reliability and productivity. Contact Metav Werkzeuge for tailored application recommendations and to procure the Walter Tools CNMG120408-MP5 WPP30G insert with Tiger·tec Gold coating for steel machining Technical data Article number: CNMG120408-MP5-WPP30G-WALTER SKU: CNMG120408-MP5-WPP30G-WALTER Designation: CNMG120408-MP5 Type: Indexable turning insert Brand: Walter Tools Series: Tiger·tec Gold Facts Geometry: Rhombic 80° Nose radius: 0.8 mm Clearance angle: 0° (negative) Plate size: 12 Plate thickness: 04 Tolerance class: M Special features Coating: Tiger·tec Gold Grade: WPP30G Chipbreaker: MP5 Material application: Steel Base material: Coated carbide FAQ What workpiece materials is this insert intended for? The CNMG120408-MP5 WPP30G is specified for machining steel (ISO group P) and is formulated to handle the heat and chip behaviour typical of unalloyed and alloyed steels. How does the MP5 chipbreaker influence performance? The MP5 chipbreaker on the CNMG120408-MP5 WPP30G promotes controlled chip formation and evacuation, improving process stability and reducing the likelihood of chip-related interruptions. What benefits does the Tiger·tec Gold coating provide? Tiger·tec Gold on this Walter Tools insert increases wear resistance while retaining toughness, which supports longer tool life and consistent cutting performance in steel turning applications. Is the 0.8 mm nose radius suitable for finishing? The 0.8 mm nose radius on the CNMG120408-MP5 WPP30G gives a reliable compromise between edge strength and surface finish, making it suitable for many finishing and medium-turning tasks. Can this insert be used in standard toolholders? Yes, the rhombic 80° geometry and standard designation CNMG120408-MP5 make the insert compatible with common turning toolholders designed for this insert form and size. Protected trademarks and trade names are the property of their respective owners. Trademarks and registered product names are mentioned for identification and explanatory purposes only; no association or endorsement by the trademark owners is implied. Manufacturer: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen, Germany
CNMG120408-MS3 WMP20G WMP20G Wendeplatten - Walter Tools
High-performance machining of stainless steel is achieved by combining the Tiger·tec Gold coating with the MS3 chipbreaker and a robust 0.8 mm cutting edge; this delivers stable chip formation and extended edge life while reducing downtime. Order the CNMG120408-MS3 WMP20G turning insert directly via Metav Werkzeuge or consult our specialists for application support. CNMG120408-MS3 WMP20G turning insert — Tiger·tec Gold coating, for stainless steel — Walter Tools CNMG120408-MS3 WMP20G is a negative-geometry turning insert designed for reliable machining of stainless steel in medium to robust conditions, combining a coated carbide grade with an MS3 chipbreaker and an 80° rhombic form for versatile lathe applications Tiger·tec Gold coating for edge stability Optimised MS3 chipbreaker for stainless steel Rhombic 80° geometry for versatile turning 0.8 mm corner radius for improved tool life Stable chip control and longer edge life for stainless steel components The CNMG120408-MS3 WMP20G insert uses Tiger·tec Gold coating together with the MS3 chipbreaker to promote dependable chip control when machining stainless steel, which commonly produces tough, work‑hardening chips. The coated carbide grade supports a stable cutting edge under elevated temperatures and promotes predictable wear behaviour; the practical benefit is fewer tool changes and more consistent component quality during medium to heavy turning operations. Geometry and mechanical benefits that secure process reliability Featuring the proven CNMG geometry in a Rhombic 80° shape and a 0.8 mm corner radius, the insert offers a balanced combination of strength and versatility. The negative 0° relief ensures a solid seat in standard toolholders and reduces the tendency for vibration in interrupted cuts. For production environments this means robust performance in facing, turning and semi‑finish passes while maintaining good component tolerances and surface condition. Where this insert fits into a productive turning strategy As part of the Tiger·tec Gold family, the insert is optimized for demanding stainless‑steel applications and supports reproducible results across batches. The grade's composition and chipbreaker design reduce edge build‑up and help to maintain cutting stability over longer tool lives, improving overall throughput. For process planners, this translates into fewer interruptions, stable cycle times and a more predictable maintenance schedule for toolholders and machines. Contact Metav Werkzeuge to discuss the Walter Tools CNMG120408-MS3 WMP20G turning insert and receive tailored recommendations for stainless steel machining in your workshop Technical data Article number: CNMG120408-MS3-WMP20G-WALTER Designation: CNMG120408-MS3 WMP20G Manufacturer: Walter Tools Product type: turning insert Core data Size: 12 Thickness: 04 Corner radius: 0.8 mm Relief angle: 0° (negative) Special features Series: Tiger·tec Gold Grade: WMP20G Chipbreaker: MS3 Plate form: Rhombus 80° Execution: G Applicable material group: M (stainless steel) FAQ What primary materials is this insert suitable for? The CNMG120408-MS3 WMP20G turning insert is designed primarily for stainless steel (material group M) and offers reliable chip control and edge life under the specific demands of these alloys. Which operations benefit most from this geometry and grade? Operators will find the rhombic 80° form and WMP20G grade effective for medium to robust roughing and semi-finishing turning operations where stable cutting and reproducible surface quality are required. How does the MS3 chipbreaker influence machining performance? The MS3 chipbreaker promotes shorter, manageable chips and reduces the risk of built-up edge on the coated carbide, improving surface finish consistency and extending effective tool life during continuous production. Is this insert compatible with standard CNMG toolholders? Yes, the insert follows CNMG seating and clamping conventions; the negative 0° relief is intended for conventional negative toolholder systems used in turning applications. What practical advantages does the Tiger·tec Gold coating deliver? The Tiger·tec Gold coating enhances thermal stability and wear resistance on the cutting edge, which benefits cycle stability, reduces flank wear, and is particularly advantageous when machining heat‑resistant stainless steels. The Walter AG (brand: Walter Tools) with headquarters in Tübingen is among the world's leading manufacturers of precision tools for metalworking and is part of the Swedish Sandvik group. Protected trademarks and trade names are the property of their respective owners. Brand names are mentioned for explanatory purposes only; there is no affiliation between our company and the named brands. The offered item is original, brand‑new merchandise from the manufacturer. Manufacturer/Responsible: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen
CNMG120408-MS3 WMP20S WMP20S Wendeplatten - Walter Tools
Take advantage of the robust edge security, Tiger‑tec Silver coating and precise chip control for reliable turning of stainless steels; order directly via Metav Werkzeuge or consult our application specialists for tailored recommendations CNMG120408‑MS3 WMP20S turning insert — Rhombus 80°, 0.8 mm radius (Walter Tools) The CNMG120408‑MS3 WMP20S is an indexable turning insert designed for demanding stainless steel applications, combining a Tiger‑tec Silver coated carbide grade with a MS3 chipbreaker for stable machining. Tiger‑tec Silver coating for wear resistance Optimised for stainless steel machining Rhombus 80° form with 0.8 mm corner radius 0° (negative) rake for robust cutting edges High process reliability for stainless steel turning The Tiger‑tec Silver‑based grade WMP20S provides a balanced combination of wear resistance and toughness specifically for stainless steel. Thanks to the coating and substrate pairing, the insert supports secure chip formation and reduces the tendency for built‑up edge in sticky, work‑hardening materials. This results in a consistently stable cut, which translates into fewer tool changes and more predictable cycle times on production runs. The description emphasises measurable process benefits rather than promises: improved edge life and repeatable performance under medium to robust conditions. Robust geometry that protects the cutting edge With a Rhombus 80° outline and a 0° (negative) rake, the insert is engineered to withstand interrupted cuts and heavier feed conditions. The negative rake increases edge strength, making the insert suitable where a more durable cutting geometry is required. The 0.8 mm corner radius provides a larger cutting edge contact, improving surface finish on roughing passes while preserving the integrity of the edge under higher loads. These geometric choices are practical solutions to common workshop challenges when machining tough stainless alloys. Chip control and machining stability explained The integrated MS3 chipbreaker is tailored to the physical behaviour of stainless steel, assisting in breaking and evacuating chips reliably even at varying depths of cut. Proper chip control lowers the risk of re‑cutting and tool damage, increasing component quality and shopfloor safety. For users less familiar with chipbreaker nomenclature: the term refers to the engineered groove and land geometry on the insert face that shapes and segments metal chips during cutting, helping maintain stable temperatures and more consistent cutting forces. Practical fitment and application notes The insert follows the standard CNMG form factor (ISO CNMG120408‑MS3), making it compatible with conventional indexable toolholders that accept 80° rhombic inserts. The designation and WMP20S grade identify its intended material group (M – stainless steels) and coating family. Where machining parameters are a concern, Metav Werkzeuge can provide guidance on feeds and speeds to exploit the insert’s advantages while ensuring process safety and productivity. Discuss machining requirements with Metav Werkzeuge to select Walter Tools Tiger‑tec Silver inserts optimised for stainless steel and receive application support by e‑mail or phone: info@metav-werkzeuge.com / +49 2822 7131930 Technical Data SKU: CNMG120408‑MS3‑WMP20S‑WALTER ISO designation: CNMG120408‑MS3 WMP20S Manufacturer: Walter Tools Data Size: 12 Thickness: 04 Corner radius: 0.8 mm Free angle: 0° (negative) Geometry: Rhombus 80° Special features Coating: Tiger‑tec Silver (coated carbide) Grade: WMP20S Chipbreaker: MS3 Application: Stainless steel Series: Tiger‑tec Silver FAQ What materials is this insert intended for? The CNMG120408‑MS3 WMP20S is formulated for machining stainless steel (ISO group M) and supports medium to robust cutting conditions. How does the MS3 chipbreaker improve machining? The MS3 chipbreaker helps shape and evacuate chips during cutting, improving thermal behaviour and reducing the risk of built‑up edge when turning stainless steels with the WMP20S grade. Is the insert compatible with standard CNMG toolholders? Yes; the ISO form CNMG120408‑MS3 ensures compatibility with conventional 80° rhombic toolholders designed for CNMG inserts. What benefits does the Tiger‑tec Silver coating provide? Tiger‑tec Silver enhances wear resistance and edge stability for the WMP20S grade, supporting longer tool life under demanding stainless steel machining. What is the effect of the 0° (negative) rake? A 0° (negative) rake increases edge robustness, making the insert more tolerant of heavier depths of cut and intermittent machining, while maintaining consistent performance. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Geschützte Markenzeichen und Warenbezeichnungen liegen im Recht ihrer jeweiligen Eigentümer. Markennamen und geschützte Warenbezeichnungen werden ausschließlich zu Erklärungszwecken genannt. Es besteht keinerlei Verbindung zwischen unserem Unternehmen und den genannten Marken. Es handelt sich bei dem angebotenen Artikel um originale fabrikneue Waren des Herstellers.
CNMG120408-MS3 WPP10G WPP10G Wendeplatten - Walter Tools
Take advantage of the combination of Tiger·tec Gold coating, the MS3 chipbreaker and a 0° negative rake for robust, repeatable steel turning; order directly via Metav Werkzeuge or ask our consultants if needed. CNMG120408‑MS3, CNMG120408‑MS3 WPP10G, WPP10G — Indexable turning insert for steel | Walter Tools A Walter Tools CNMG120408‑MS3 WPP10G indexable turning insert engineered for reliable steel machining with a Tiger·tec Gold coating and an MS3 chipbreaker Tiger·tec Gold coated carbide MS3 chipbreaker for stable chips 0° negative rake for secure cutting Durable coating for longer cutting cycles and consistent results The combination of the Tiger·tec Gold coating with the WPP10G grade delivers a high degree of wear resistance and thermal stability, which translates into longer tool life and fewer changeovers. Designed specifically for machining steel, the coating technology reduces flank and crater wear during continuous production runs. For operations requiring consistent dimensional results, the enhanced surface protection helps maintain cutting edge integrity and reduces the likelihood of premature edge failure, supporting predictable process cycles and improved component quality. Stable chip control and secure cutting under demanding conditions The integrated MS3 chipbreaker is optimised for reliable chip formation when turning steel, promoting short, controllable chips that ease evacuation and reduce cycle disruptions. Combined with the 0° (negative) rake angle, the geometry increases edge strength and allows the insert to resist shock loads and interrupted cuts more effectively. The 0.8 mm corner radius and rhombus 80° shape provide a balance between edge robustness and dimensional versatility, enabling secure cutting in a range of feed conditions without compromising component tolerances. Standard form factor for straightforward integration and efficiency gains With the standard CNMG format and clear ISO designation, the insert fits common toolholders and simplifies tool management on the shopfloor. The marked designation and series information support quick identification and reproducible setup, reducing downtime during insert changes. By offering a combination of robust geometry, a mature chipbreaker and a process-oriented coating, this insert helps to increase productivity while keeping inventory management simple and tooling costs predictable across batch and series production. For demanding steel turning, choose Walter Tools Tiger·tec Gold inserts and contact Metav Werkzeuge for tailored recommendations and availability: info@metav-werkzeuge.com — +49 2822 7131930 Technical data Article number: CNMG120408-MS3-WPP10G-WALTER Type: Indexable turning insert Designation: CNMG120408-MS3 WPP10G Manufacturer: Walter Tools Series: Tiger·tec Gold Specifications Inscribed circle: 12 Thickness code: 04 Corner radius: 0.8 Rake angle: 0° (negative) Shape: Rhombus 80° Tolerance class: M Special features Coating: Tiger·tec Gold Grade: WPP10G Chipbreaker: MS3 Application: Steel (P) Execution: G Plate form: CNMG120408-MS3 Series description: Tiger-tec Gold FAQ What materials is this insert suitable for? This CNMG120408‑MS3 WPP10G insert is specified for machining steel (P) and is formulated to cope with the thermal and chip-formation behaviour typical of steel turning. How does the MS3 chipbreaker affect machining performance? The MS3 chipbreaker promotes short, controllable chips in steel turning, improving chip evacuation and reducing the risk of built-up edge, which helps maintain consistent surface finishes and process stability. Is the 0° negative rake angle suitable for interrupted cuts? Yes, the 0° (negative) rake increases edge strength and makes the insert more resistant to shocks and interruption, supporting more demanding turning operations. Can this insert be mounted in common CNMG toolholders? The insert follows the CNMG format and ISO designation, making it compatible with standard CNMG toolholders for straightforward integration. What does the WPP10G grade provide compared with other grades? WPP10G, part of the Tiger·tec Gold family, combines coating and substrate properties for improved wear resistance and thermal stability during steel turning, aiming to extend tool life and reduce tool changes. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Trademarked names and product designations are the property of their respective owners. Brand names and trademarks are mentioned for explanatory purposes only. There is no connection between our company and the named brands. The offered item is original factory-new goods of the manufacturer.
CNMG120408-MS3 WPP20G WPP20G Wendeplatten - Walter Tools
Reliable productivity and broad material coverage meet in the Tiger‑tec Gold grade: stable chip control, long tool life and consistent edge security ensure efficient steel turning. Order the CNMG120408‑MS3 WPP20G turning inserts directly via Metav Werkzeuge or consult our specialists for tailored support. CNMG120408‑MS3 WPP20G — Turning insert (Rhombic 80°) for steel — Walter Tools The CNMG120408‑MS3 WPP20G is a rhombic 80° coated‑carbide turning insert engineered for productive machining of steel, combining the Tiger‑tec Gold grade with an MS3 chipbreaker for stable performance Tiger‑tec Gold coated carbide technology Optimised MS3 chipbreaker for stable chips Rhombic 80° form with 0.8 mm corner radius Suitable for steel machining (ISO P) Maximum process reliability and extended tool life The combination of Tiger‑tec Gold coating and the WPP20G coated‑carbide grade delivers enhanced wear resistance and consistent cutting‑edge stability. This results in fewer tool changes and longer uninterrupted runs, which positively affects overall productivity. The grade is optimised for the thermal and chip‑formation characteristics typical of steel machining and supports a balanced compromise between toughness and wear resistance. Consistent chip control for uninterrupted production The MS3 chipbreaker is designed to produce short, controllable chips when cutting steels, reducing risks of chip entanglement and machine stoppages. Clear advantages include improved surface finish and a lower likelihood of built‑up edge; by controlling chip flow the insert helps maintain cutting conditions and part tolerances over longer tool life, thereby supporting consistent cycle times and reduced rework. Robust geometry for versatile turning applications The rhombic 80° geometry paired with a 0.8 mm corner radius offers a reliable edge for a wide range of turning operations, from finishing to light roughing in steels. The 0° (negative) clearance angle provides secure clamping and edge strength under intermittent cuts. The insert size (12 mm inscribed circle) and the coded thickness ensure compatibility with standard CNMG toolholders, making integration into existing toolsets straightforward and cost‑effective. Contact Metav Werkzeuge for expert advice on Walter Tools Tiger‑tec Gold inserts and availability of CNMG120408‑MS3 WPP20G — eMail info@metav-werkzeuge.com or call +49 2822 7131930 Technical Data SKU: CNMG120408-MS3-WPP20G-WALTER Designation (ISO): CNMG120408-MS3 WPP20G Series: Tiger‑tec Gold Grade: WPP20G Manufacturer: Walter Tools Facts Corner radius: 0.8 mm Form: Rhombus 80° Clearance angle: 0° (negative) Inscribed circle / size: 12 mm Thickness code: 04 Tolerance class: M Special features Coated carbide grade WPP20G (Tiger‑tec Gold) MS3 chipbreaker geometry Material group: P (steel) Application: Turning / indexable insert Execution: G FAQ What materials is this insert recommended for? The CNMG120408‑MS3 WPP20G insert is specified for machining steels (ISO group P) and is engineered to handle the heat and chip formation typical of steel turning. How does the MS3 chipbreaker improve performance? The MS3 chipbreaker on this Walter Tools insert produces short, controlled chips that reduce entanglement and interruptions, improving surface finish and enabling longer uninterrupted cutting times. Is the geometry suitable for finishing operations? Yes, the rhombic 80° form with a 0.8 mm corner radius gives a robust edge appropriate for finishing and light roughing in steel components. Can the insert be used in standard CNMG toolholders? The CNMG120408‑MS3 designation corresponds to standard CNMG toolholders; verify holder compatibility with the inscribed circle (12 mm) and thickness code before mounting. Manufacturer: Walter Tools; Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Protected trademarks and trade names are the property of their respective owners. Brand names and registered trademarks are used for identification purposes only and do not imply any affiliation with our company. The offered item is an original, factory‑new product of the stated manufacturer. The Walter AG brand (marketed as Walter Tools) is part of the Sandvik group and is known for precision tools and reliable performance.
CNMG120408-MS3 WSM01 WSM01 Wendeplatten - Walter Tools
Take advantage of the combination of Tiger‑tec Silver wear resistance, a dedicated WSM01 coated‑carbide grade and the MS3 chipbreaker to secure stable cutting performance in stainless steels and superalloys; order or request application advice directly via Metav Werkzeuge. CNMG120408-MS3 WSM01 rhombic 80° turning insert, Tiger‑tec Silver — Walter Tools The CNMG120408-MS3 WSM01 is a rhombic 80° turning insert designed for heavy duty machining of stainless steels and heat‑resistant superalloys, providing stable chip formation and extended edge life. Tiger‑tec Silver coated carbide Optimised for stainless steels and superalloys Rhombic 80° geometry, 0° negative rake MS3 chipbreaker for reliable chip control Secure machining of difficult materials with consistent results The Tiger‑tec Silver series, combined with the WSM01 coated carbide grade, is engineered for processes where thermal load and material toughness challenge tool life. This insert offers a rhombic 80° geometry and a 0° negative rake that together increase cutting edge support and reduce the risk of edge collapse when machining stainless steels and nickel‑based alloys. The result is reproducible surface finish and fewer in‑process interrupts, which supports predictable cycle times and productivity improvements in series turning. Stable chip control that protects the cutting edge and the component Equipped with the MS3 chipbreaker, the insert promotes segmented chip formation and reduces entanglement on both continuous and interrupted cuts. That controlled chip flow lessens mechanical shock to the cutting edge and contributes directly to edge stability and longer tool life. For operators and process planners this translates to reduced rework and lower frequency of insert changes, so set‑up consistency and throughput remain high over longer production runs. Practical benefits for toolroom and production use The moderate 0.8 mm corner radius balances robustness and finish capability: it strengthens the edge for heavy cuts while still enabling acceptable surface quality without aggressive cutting parameters. The insert’s form factor and standard ISO designation facilitate straightforward integration into common turning toolholders, making it a pragmatic choice for shops that require rapid deployment and reliable performance across a range of turning tasks. Focus on process reliability and predictable maintenance Selecting a dedicated grade like WSM01 minimises the trial‑and‑error phase in process development. The coating and substrate combination is tailored to handle the heat and adhesion tendencies of stainless steels and superalloys, supporting a stable cutting edge and efficient material removal. This reduces machining variability and simplifies maintenance planning, so machine uptime is maximised and tool stock management becomes more predictable. Contact Metav Werkzeuge for tailored recommendations on using Walter Tools Tiger‑tec Silver inserts in specific applications — call +49 2822 7131930 or email info@metav-werkzeuge.com to request cutting data or a machining consultation Technical data SKU: CNMG120408-MS3-WSM01-WALTER Designation: CNMG120408-MS3 ISO designation: CNMG120408-MS3 WSM01 Series: Tiger‑tec Silver Grade: WSM01 Manufacturer: Walter Tools Core data Geometry: Rhombus 80° Free rake: 0° (negative) Corner radius: 0.8 Size designation: 12 Thickness code: 04 Tolerance class: M Special features Chipbreaker: MS3 Coating/substrate: coated carbide Suitable for: stainless steels (M), heat‑resistant superalloys / titanium (S) Execution: G Shape: Rhombus 80° FAQ What materials is this insert suitable for? This turning insert from Walter Tools is designed primarily for stainless steels (ISO group M) and heat‑resistant superalloys / titanium (ISO group S); the WSM01 grade supports secure chip formation in these materials. Which chipbreaker is fitted and what is the benefit? The MS3 chipbreaker promotes segmented chips and improved chip control, which protects the cutting edge and reduces the risk of chip entanglement during turning operations with the CNMG120408‑MS3 WSM01. How does the 0.8 corner radius affect performance? A 0.8 corner radius strengthens the cutting edge for heavier cuts while maintaining acceptable surface quality, providing a compromise between robustness and finish when machining difficult materials. Can the insert be used in standard toolholders? Yes, the insert’s ISO geometry (CNMG120408) and rhombic 80° form make it compatible with common turning toolholders that accept CNMG‑type inserts. What production benefits can be expected from Tiger‑tec Silver and WSM01? The Tiger‑tec Silver coating together with the WSM01 substrate improve wear resistance and thermal stability, leading to more predictable tool life and reduced downtime in series production with challenging alloys. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen, Germany; Walter Tools is a brand of Walter AG Geschützte Markenzeichen und Warenbezeichnungen liegen im Recht ihrer jeweiligen Eigentümer. Markennamen und geschützte Warenbezeichnungen werden ausschließlich zu Erklärungszwecken genannt. Es besteht keinerlei Verbindung zwischen unserem Unternehmen und den genannten Marken. Es handelt sich bei dem angebotenen Artikel um originale fabrikneue Waren des Herstellers Walter Tools.
CNMG120408-MS3 WSM10S WSM10S Wendeplatten - Walter Tools
Take advantage of the combination of high-temperature capability, stable chip formation and precise edge geometry for consistent turning results in demanding materials; order original Walter Tools inserts directly via Metav Werkzeuge or consult our advisors for machining recommendations. CNMG120408-MS3 WSM10S indexable turning insert (Rhombic 80°) – Walter Tools, Tiger·tec Silver The CNMG120408-MS3 WSM10S is a coated carbide indexable insert engineered for robust turning of stainless steels and heat-resistant superalloys in industrial production. Tiger·tec Silver coated grade Optimised for stainless steels and superalloys Rhombic 80° CNMG geometry for versatile clamping 0.8 mm nose radius with MS3 chipbreaker High-performance grade for demanding materials The WSM10S grade, produced with the Tiger·tec Silver coating, offers a combination of wear resistance and thermal stability that benefits long cycle times and interrupted cuts. As a coated carbide insert developed for the machining of stainless steels and superalloys, it supports secure chip formation and reduces the risk of built-up edge. The selectable, heat-resistant coating technology is aimed at maintaining cutting-edge integrity under elevated temperatures, which in turn improves process repeatability and reduces rework. Geometry and chip control that increase productivity With the characteristic CNMG geometry and a rhombic 80° profile, this insert provides broad accessibility to turning applications and flexible tool-holder compatibility. The MS3 chipbreaker is tuned to promote controlled chip formation for medium to heavy cuts, improving surface finish and reducing downtime from chip-related issues. The 0° negative rake design increases edge strength for tougher engagements, while the 0.8 mm nose radius balances surface quality with robust edge life. Reliability and reduced machining risk Designed for production environments where consistency matters, the insert’s tolerance class and execution ensure predictable seating and repeatable results. The combination of a stable cutting edge and an optimised chipbreaker enhances both dimensional control and component finish. This leads to fewer in-process interruptions and contributes to overall line efficiency, supporting the case for cost-effective machining in serial production. Practical application and handling advice The insert is suitable for turning tasks where stainless steels and heat-resistant alloys challenge tool life and process stability. Use the plate with appropriate tool-holders for CNMG-style inserts and ensure machining parameters are adapted to the workpiece material and rigidity of the setup. Regular inspection of the cutting edge and correct clamping torque will secure process reliability and prolong tool-life, while correct coolant strategy will support the grade’s thermal performance. For machining enquiries or tailored recommendations for Walter Tools Tiger·tec Silver inserts, contact Metav Werkzeuge’s technical sales team at info@metav-werkzeuge.com or call +49 2822 7131930 to discuss suitable grades and tooling strategies Technical data Article number: CNMG120408-MS3-WSM10S-WALTER Designation: CNMG120408-MS3 WSM10S SKU: CNMG120408-MS3-WSM10S-WALTER Facts Corner radius: 0.8 mm Relief angle: 0° (negative) Insert size: 12 Thickness: 04 Tolerance class: M Special features Series: Tiger·tec Silver Grade: WSM10S Chipbreaker: MS3 Shape: Rhombic 80° Material suitability: S / M (superalloys/titanium and stainless steels) Execution: G Manufacturer: Walter Tools FAQ What materials is this insert suited for? The CNMG120408-MS3 WSM10S indexable turning insert is specified for stainless steels and heat-resistant superalloys (groups M and S), offering thermal stability and secure chip formation for these challenging materials. How does the negative rake influence cutting performance? A 0° negative rake increases edge robustness, making the insert more resistant to edge chipping during heavy interruptions or tough engagements; this characteristic supports longer edge life for the CNMG120408-MS3 WSM10S. What benefit does the MS3 chipbreaker provide? The MS3 chipbreaker promotes controlled chips and stable evacuation in medium to heavy turning, improving surface finish and reducing the likelihood of chip-related machine stoppages. Is the insert compatible with standard CNMG holders? Yes, the rhombic 80° CNMG geometry matches standard CNMG tool-holders; correct clamping and seating are essential to achieve the stated tolerances and repeatable performance. How should tool-life be maximised with this grade? Maximise tool-life by selecting cutting parameters aligned with the workpiece and machine rigidity, maintaining appropriate coolant or lubrication practices, and inspecting the insert edge regularly for wear on the CNMG120408-MS3 WSM10S. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen, Germany The Walter AG (brand: Walter Tools) with headquarters in Tübingen is one of the world’s leading manufacturers of precision tools for metalworking and is part of the Swedish Sandvik group. Protected trademarks and trade names are the property of their respective owners. Brand names and registered trademarks are mentioned for explanatory purposes only; there is no affiliation between our company and the named brands. The offered article is an original, brand-new product from the manufacturer.
CNMG120408-MS3 WSM20S WSM20S Wendeplatten - Walter Tools
Take advantage of the combination of Tiger‑tec Silver coating and the MS3 chipbreaker for reliable chip control and extended tool life; order the insert directly via Metav Werkzeuge or consult the team for application advice. CNMG120408‑MS3 WSM20S indexable turning insert — for stainless steels and superalloys, Walter Tools The CNMG120408‑MS3 WSM20S is a rhombic 80° indexable turning insert designed for heavy‑duty finishing and semi‑finishing of stainless steels and heat‑resistant superalloys. Tiger‑tec Silver coating for high process security Optimised MS3 chipbreaker for stable chip control Rhombic 80° form with 0.8 mm corner radius Suitable for stainless steel and superalloys (M/S) Reliable machining of demanding materials with predictable edge behaviour The combination of the WSM20S grade and the Tiger‑tec Silver coating provides a rational foundation for consistent production results when working with tough, heat‑sensitive alloys. The coated carbide substrate supports stable chip formation, reducing the risk of built‑up edge and thermal overload; this translates into fewer interruptions on the shop floor and improved process security. For operations that require repeatable part tolerances, the coated grade offers improved surface finish and tool life compared with uncoated grades, making it a cost‑effective choice across small and large batch runs. Geometry engineered to prolong tool life and improve surface quality The insert’s rhombic 80° geometry and 0.8 mm corner radius deliver a balanced combination of strength and cutting performance. A 0° negative rake increases edge robustness in interrupted cuts and heavy feeds, while the MS3 chipbreaker is optimised to control swarf and evacuate chips reliably. These features reduce rework and inspection cycles by helping to maintain a consistent cutting edge, which benefits productivity and lowers overall machining cost per component. The result is a measurable improvement in both component finish and tool longevity. Easy integration into existing turning tool systems and workflows With the standard CNMG form factor and the series’ focus on process stability, the insert integrates smoothly into established tooling setups, minimising change‑over time. The grade’s suitability for group M (stainless steels) and group S (heat‑resistant superalloys and titanium) makes inventory management simpler by covering a wide material range with one insert family. Technical enquiries regarding application parameters or grade selection can be addressed quickly by the supplier to ensure the insert performs as intended in specific cutting conditions. Contact Metav Werkzeuge for tailored recommendations on Walter Tools Tiger‑tec Silver inserts and to secure immediate delivery or application support — eMail: info@metav-werkzeuge.com | Tel: +49 2822 7131930 Technical Data Article number: CNMG120408-MS3-WSM20S-WALTER Label: Drehwendeschneidplatte CNMG120408-MS3 WSM20S Walter Tools Manufacturer: Walter Tools Product type: Indexable turning insert Series: Tiger‑tec Silver Grade: WSM20S Chipbreaker: MS3 Form: Rhombus 80° Free angle: 0° (negative) Corner radius: 0.8 mm Insert size: 12 Thickness code: 04 Substrate / coating: coated carbide Material suitability: Stainless steels (M), Superalloys/Titanium (S) Core technical data Corner radius: 0.8 mm Free angle: 0° (negative) Insert size: 12 Thickness: 04 Tolerance class: M Special features Tiger‑tec Silver coating technology WSM20S coated carbide grade MS3 optimised chipbreaker Rhombic 80° insert geometry Suitable for stainless steels and heat‑resistant superalloys Robust edge for interrupted cuts and high thermal loads FAQ What materials is this insert best suited for? The CNMG120408‑MS3 WSM20S insert is designed primarily for stainless steels (M) and heat‑resistant superalloys/titanium (S), where the Tiger‑tec Silver coating aids thermal resistance and chip control. How does the MS3 chipbreaker benefit machining? The MS3 chipbreaker provides consistent chip formation and evacuation for finishing and semi‑finishing cuts, reducing the likelihood of built‑up edge and improving process stability with the CNMG120408‑MS3 insert. Can this insert withstand interrupted cuts? Yes. The combination of a 0° negative rake and the rhombic 80° geometry gives the insert enhanced edge strength suited to interrupted cuts and heavy feed conditions. Is the insert compatible with standard CNMG tool holders? The insert follows the CNMG form factor and is compatible with standard CNMG tool holders; correct clamping and seat cleanliness ensure repeatable performance. What improvements in surface finish can be expected? The WSM20S grade and coating improve edge stability and reduce thermally induced roughness, resulting in a more consistent surface finish compared with uncoated alternatives. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Geschützte Markenzeichen und Warenbezeichnungen liegen im Recht ihrer jeweiligen Eigentümer. Markennamen und geschützte Warenbezeichnungen werden ausschließlich zu Erklärungszwecken genannt. Es besteht keinerlei Verbindung zwischen unserem Unternehmen und den genannten Marken. Es handelt sich bei dem angebotenen Artikel um originale fabrikneue Waren des Herstellers.
CNMG120408-MS3 WSM30S WSM30S Wendeplatten - Walter Tools
Take advantage of a robust cutting solution that combines the WSM30S grade and Tiger‑tec Silver coating for improved heat resistance and extended tool life; the CNMG geometry with a 0.8 mm corner radius and MS3 chipbreaker delivers reliable chip control and process stability. Order genuine inserts via Metav Werkzeuge or consult their specialists for application-specific recommendations. CNMG120408-MS3 WSM30S turning insert — Tiger‑tec Silver grade for rostfreier Stahl and superalloys | Walter Tools The CNMG120408-MS3 WSM30S is a rhombic 80° indexable turning insert engineered for heavy-duty and demanding machining of rostfreier Stahl and heat‑resistant superalloys. Tiger‑tec Silver coated for heat resistance Designed for rostfreier Stahl and superalloys Rhombic 80° CNMG form with 0.8 mm corner radius MS3 chipbreaker for stable chip formation Extended cutting performance for hard-to-machine materials The combination of the WSM30S grade and Tiger‑tec Silver coating offers a blend of thermal stability and wear resistance that is particularly valuable when machining rostfreier Stahl and nickel‑based alloys. The coated carbide substrate reduces flank wear and supports a more consistent tool life, which in turn lowers tool change frequency and improves uptime. For production environments where component conformity and repeatability matter, the enhanced resistance to thermal softening helps maintain cutting-edge geometry over longer cycles while promoting stable chip formation under demanding conditions. Geometry that improves process reliability and surface quality The CNMG rhombic 80° form paired with a 0.8 mm corner radius gives a strong edge for interrupted cuts and medium to heavy turning operations. The negative 0° clearance configuration increases edge strength and reduces the risk of edge chipping during heavy engagement, while the MS3 chipbreaker is tuned to produce controllable chips and support a consistent surface finish. These geometric attributes reduce vibration and support predictable cutting forces, which benefits both tool life and component tolerance achievement in serial production. Practical advantages and application fit for productive cutting As an indexable insert, the CNMG120408-MS3 WSM30S is suitable for series production where process security and repeatable outcomes are priorities. The combination of grade, coating and chipbreaker offers productive cutting with lower scrap rates when matched to the correct cutting data for the material. Its compatibility with standard CNMG toolholders ensures straightforward integration into existing tool systems, and the insert’s build delivers a reliable balance between robustness and achievable surface quality for turned parts made from rostfreier Stahl or high-temperature superalloys. Contact Metav Werkzeuge today for tailored machining advice and to request genuine Walter Tools CNMG120408-MS3 WSM30S inserts — eMail: info@metav-werkzeuge.com | Tel: +49 2822 7131930 Technical data Article number: CNMG120408-MS3-WSM30S-WALTER SKU: CNMG120408-MS3-WSM30S-WALTER Name: Drehwendeschneidplatte CNMG120408-MS3 WSM30S Walter Tools Manufacturer: Walter Tools Series: Tiger-tec Silver Grade: WSM30S Core data Insert form: Rhombus 80° Plate size: 12 Corner radius: 0.8 mm Plate thickness: 04 Clearance angle: 0° (negative) Tolerance class: M Special features Coating: Tiger‑tec Silver Chipbreaker: MS3 Material suitability: S / M Application focus: rostfreier Stahl and heat‑resistant superalloys ISO designation: CNMG120408-MS3 WSM30S Execution: G FAQ Which materials is this insert intended for? The CNMG120408-MS3 WSM30S by Walter Tools is optimised for rostfreier Stahl (ISO group M) and heat‑resistant superalloys/Titanium (ISO group S), addressing the thermal and mechanical challenges typical of these materials. What benefits does the Tiger‑tec Silver coating provide? The Tiger‑tec Silver coating on the WSM30S grade improves thermal resistance and reduces adhesive wear, which helps maintain cutting-edge geometry and extends the usable life of the insert under high heat loads. How does the MS3 chipbreaker influence machining? The MS3 chipbreaker is designed to produce short, controllable chips and support consistent chip evacuation, contributing to stable cutting forces and improved surface quality when machining difficult alloys. For which operations is the rhombic 80° CNMG geometry most suitable? The rhombic 80° CNMG form with a 0.8 mm corner radius is well suited to medium and heavy turning, including interrupted cuts; it provides a robust edge for stable machining rather than ultra‑fine finishing tasks. Manufacturer/Responsible: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen; Germany Protected trademarks and trade names are the property of their respective owners. Brand names and registered trademarks are mentioned for explanation only and do not imply any affiliation between our company and the trademark owners. The offered article is an original factory‑new product of the named manufacturer.
CNMG120408-MU5 WMP20G MU5 Wendeplatten - Walter Tools
Take advantage of the Tiger·tec Gold grade together with the MU5 chipbreaker and a 0.8 mm corner radius for dependable machining of rostfreier Stahl; these features ensure stable chip formation and long-lasting cutting edges. Order the CNMG120408-MU5 WMP20G directly via Metav Werkzeuge or consult our specialists for process advice. CNMG120408-MU5 WMP20G — Turning insert (Rhombus 80°, 0° negative), Walter Tools The CNMG120408-MU5 WMP20G is a rhombic 80° indexable turning insert designed for robust machining of rostfreier Stahl under medium to heavy conditions. Tiger·tec Gold coated carbide grade MU5 chipbreaker for reliable chip control 0° negative rake for heavy-duty turning 0.8 mm corner radius for edge strength Consistent performance on rostfreier Stahl for improved cycle times The Tiger·tec Gold coating and the WMP20G grade deliver a balanced performance specifically tuned for rostfreier Stahl, a group of alloys prone to built-up edge and high heat. By combining a wear-resistant PVD/CVD-style coating with a substrate optimised for toughness, this insert supports stable cutting edges and reduced flank wear over extended cycles. The result is fewer interruptions for tool change and more predictable component quality, which translates directly into improved process throughput and reproducible surface finish. Secure chip control and edge integrity with MU5 geometry The MU5 chipbreaker is engineered to produce short, controllable chips when turning challenging stainless alloys; this lowers the risk of entanglement and facilitates safe, automated operation. In conjunction with the 0° (negative) rake geometry, the insert offers a secure cutting action and resistance to thermal shock during interrupted cuts. The 0.8 mm corner radius increases the edge strength, allowing slightly higher depths of cut without compromising the insert life—an advantage for shops aiming for steady material removal rates while preserving dimensional accuracy. Practical benefits for workshop integration and process reliability As a rhombic 80° insert with a compact profile, this solution fits a broad range of standard CNMG toolholders and supports both finishing and roughing steps in a streamlined tool set. The coated cemented carbide composition and the Tiger·tec Gold technology help to extend tooling intervals and reduce overall tooling costs per part. For production planners, the combination of wear resistance and chip control means fewer unplanned stops and a simpler inventory of grades for rostfreie Stähle, making process planning and quality assurance more straightforward. Contact Metav Werkzeuge for tailored recommendations on Walter Tools Tiger·tec Gold inserts and assistance with selection or ordering. Technical Data SKU: CNMG120408-MU5-WMP20G-WALTER Designation: CNMG120408-MU5 WMP20G Product type: Turning insert (indexable) Brand: Walter Tools Series: Tiger·tec Gold Core specifications Plate shape: Rhombus 80° Free cutting angle: 0° (negative) Corner radius: 0.8 Plate size: 12 Thickness code: 04 Tolerance class: M Special features Chipbreaker: MU5 Grade: WMP20G (coated cemented carbide) Optimised for: rostfreier Stahl Application areas: medium to robust cutting conditions FAQ What materials is this insert suitable for? The CNMG120408-MU5 WMP20G insert from Walter Tools is optimised for rostfreier Stahl and performs well under medium to robust cutting conditions. How does the MU5 chipbreaker affect machining? The MU5 geometry promotes controlled, short chips and reduces the likelihood of entanglement, improving safety and uptime when turning rostfreier Stahl with the Walter Tools insert. Can this insert be used for finishing operations? Yes, the rhombic 80° form with a 0.8 mm corner radius allows for both finishing and semi-finishing work; the Tiger·tec Gold coating helps maintain surface quality across cycles. Is the grade suitable for automated turning centres? The stable chip formation and wear resistance of the WMP20G grade make it well suited for automated turning centres where consistent edge life and predictable tool change intervals are important. Hersteller: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen; Germany Die Walter AG (Markenauftritt: Walter Tools) mit Hauptsitz in Tübingen gehört zu den weltweit führenden Herstellern von Präzisionswerkzeugen für die Metallbearbeitung und ist Teil des schwedischen Sandvik-Konzerns. Geschützte Markenzeichen und Warenbezeichnungen liegen im Recht ihrer jeweiligen Eigentümer. Markennamen und geschützte Warenzeichen werden ausschließlich zu Erklärungszwecken genannt. Es besteht keinerlei Verbindung zwischen unserem Unternehmen und den genannten Marken. Es handelt sich bei dem angebotenen Artikel um originale fabrikneue Waren des Herstellers.
CNMG120408-MU5 WMP20S WMP20S Wendeplatten - Walter Tools
Combining the Tiger‑tec Silver coated carbide grade with the MU5 chipbreaker ensures consistent edge stability and reliable chip control when machining stainless steels; the rhombic 80° form with a 0.8 mm corner radius and 0° negative rake supports productive turning under medium to robust conditions. Order the CNMG120408‑MU5 WMP20S directly via Metav Werkzeuge or consult the Metav team for process recommendations. CNMG120408-MU5 WMP20S – Indexable turning insert for stainless steel, Tiger‑tec Silver (Walter Tools) CNMG120408-MU5 WMP20S is an indexable turning insert designed for productive turning of stainless steels, featuring a coated carbide grade and a MU5 chipbreaker for controlled chip formation. Coated carbide Tiger-tec Silver Dedicated for stainless steel (M) Rhombic 80° form, 0.8 mm corner MU5 chipbreaker for reliable chips High process reliability for stainless steel machining The CNMG insert offers stable cutting performance through the Tiger‑tec Silver coating and a specialised carbide substrate. These properties reduce the tendency for built-up edge and support reproducible cutting results when working with stainless steel, which is prone to toughness and heat generation. The rhombic 80° geometry combined with a 0.8 mm corner radius balances strength and accessibility, enabling consistent surface quality even under intermittent or demanding cutting conditions. The MU5 chipbreaker contributes to predictable chip shape and evacuation, which supports uninterrupted cycle times and fewer interruptions for manual chip clearing. Improved productivity through controlled chip formation and edge life The MU5 chipbreaker and the coated grade aim to deliver secure chip control and extended tool life, reducing the frequency of tool changes and downtime. The insert’s 0° negative rake provides robustness at the cutting edge, helping to withstand higher mechanical loads during heavier cuts. This combination translates into a cost‑efficient machining process by lowering tool consumption and stabilising part quality across production runs. Where repeatability is required, the insert’s geometry and coating help maintain dimensional tolerance and surface finish consistency. Practical application notes and process support The insert is suited to medium to robust turning operations in the ISO M group (stainless steels). Selection of cutting data should consider the workpiece material’s specific heat and ductility; the coated carbide and MU5 chip control assist in preventing edge build‑up and in achieving regular chip shapes. For process setup and optimisation, technical consultation is available, and the insert is compatible with standard CNMG toolholders. For supplementary technical specifications or application-specific recommendations, contact the Metav Werkzeuge technical team for assistance and cutting data tailored to the material and turning process. For process‑critical stainless steel turning choose the Walter Tools CNMG120408‑MU5 WMP20S via Metav Werkzeuge for reliable chip control and reproducible edge life; contact Metav Werkzeuge for detailed machining advice and local availability. Technical Data SKU: CNMG120408-MU5-WMP20S-WALTER Article designation: CNMG120408-MU5 WMP20S Product type: Indexable turning insert (drehwendeschneidplatte) Facts Inscribed circle / size: 12 Thickness: 04 Corner radius: 0.8 mm Free angle / rake: 0° (negative) Geometry: Rhombus 80° Special features Grade / sort: WMP20S Coating technology: Tiger‑tec Silver Chipbreaker: MU5 Material group application: stainless steel (M) Execution: G Tolerance class: M Manufacturer: Walter Tools FAQ What materials is this insert suitable for? The CNMG120408‑MU5 WMP20S is specified for stainless steel machining (ISO group M) and is designed to manage the toughness and heat tendencies of those alloys. How does the MU5 chipbreaker affect machining? The MU5 chipbreaker promotes controlled chip formation and evacuation, improving process stability and reducing the risk of built‑up edge during turning with the CNMG120408‑MU5 WMP20S insert. Which geometry and corner radius does the insert provide? The insert uses a rhombic 80° form with a 0.8 mm corner radius, offering a balance between edge strength and access for typical turning tasks. Is the CNMG120408‑MU5 WMP20S suitable for heavy roughing? The negative 0° rake and robust coated carbide grade make the insert appropriate for medium to robust cutting conditions; specific parameters should be aligned with the machining strategy and workpiece properties. Can standard CNMG holders be used with this insert? Yes, the CNMG120408‑MU5 WMP20S conforms to standard CNMG dimensions and can be mounted in conventional CNMG toolholders; ensure correct clamping and orientation according to the holder manufacturer’s guidance. Manufacturer/Responsible: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen Protected trademarks and trade names are the property of their respective owners. Brand names and protected designations are mentioned for explanatory purposes only. There is no affiliation between our company and the named brands. The offered article is original, brand‑new goods from the manufacturer.
CNMG120408-MU5 WPP05G WPP05G Wendeplatten - Walter Tools
The combination of high wear resistance from the Tiger‑tec Gold coating, a MU5 chipbreaker for stable chip control and the robust 0.8 mm corner radius delivers consistent productivity in steel turning; order the insert directly via Metav Werkzeuge or consult our specialists for application advice. CNMG120408-MU5 WPP05G Turning Insert (for Steel) by Walter Tools – Tiger‑tec Gold, MU5 The CNMG120408-MU5 WPP05G is a rhombic 80° indexable turning insert optimised for steel machining, offering Tiger‑tec Gold coating and a MU5 chipbreaker for predictable chip formation and extended tool life Tiger·tec Gold coating for extended tool life Designed for steel machining (ISO P) MU5 chipbreaker for consistent chip control 0.8 mm corner radius for robust edge stability Productivity through advanced coating and wear resistance The combination of Tiger‑tec Gold coating and a coated‑carbide base grade provides improved wear resistance and thermal stability during continuous turning. The coating technology reduces flank and crater wear under the heat loads typical for ISO P materials, enabling longer cutting times between insert changes. Fewer interruptions for tool replacement translate into higher machine uptime and more predictable process output for short‑ and long‑run production. Consistent chips and surface quality for reliable process control The integrated MU5 chipbreaker produces uniform chips and supports stable cutting forces when machining steel, which helps to maintain a steady feed and better dimensional repeatability. As a result, the insert contributes to an improved surface finish and reduced need for rework. This predictability supports process standardisation on the shop floor and simplifies selection of cutting parameters in documented machining cycles. Robust geometry for heavy and interrupted cuts The rhombic 80° form with a 0.8 mm corner radius and a 0° (negative) relief angle gives the insert mechanical stability under higher radial loads and when cutting interrupted profiles. The geometry is suited to applications where edge strength is essential and where resilience against chipping improves overall tool life. The insert's design supports a balance between edge durability and acceptable cutting forces for medium‑duty steel turning. Clear application range and economical performance Marked for ISO P steels and supplied in the WPP05G grade of the Tiger‑tec Gold series, the insert covers a broad steel spectrum from general to slightly wear‑resistant applications. The M tolerance class supports reproducible positioning in standard toolholders and reduces setup variability. Taken together, the material compatibility, chipformer and tolerance specification create a cost‑effective solution for routine turning tasks in component manufacturing. For production environments seeking stable, long‑life turning performance with Tiger‑tec Gold, contact Metav Werkzeuge to discuss ordering CNMG120408‑MU5 WPP05G and to receive tailored application guidance via info@metav-werkzeuge.com or +49 2822 7131930 Technical data SKU: CNMG120408-MU5-WPP05G-WALTER Article designation: CNMG120408-MU5 WPP05G Type: Indexable turning insert Manufacturer: Walter Tools Key dimensions Inscribed circle: 12 mm Thickness: 04 Corner radius: 0.8 mm Relief angle: 0° (negative) Features & applications Series: Tiger‑tec Gold Grade/sort: WPP05G Chipbreaker: MU5 Application group: ISO P (steel) Tolerance class: M Plate form: Rhombic 80° Execution: G FAQ Which materials is this insert intended for? The CNMG120408‑MU5 WPP05G turning insert is specified for ISO P materials and is designed primarily for machining various steels. What are the main geometric characteristics of the insert? Key dimensions include an inscribed circle of 12 mm, a corner radius of 0.8 mm, a thickness designation of 04 and a rhombic 80° plate form. What chip control and coating are used? This insert features the MU5 chipbreaker and the Tiger‑tec Gold coated carbide grade WPP05G for enhanced wear resistance and stable chip formation. Is the insert suitable for stainless steel? Stainless steel suitability is not specified for this grade; the CNMG120408‑MU5 WPP05G is designated for ISO P (steel) applications. What tolerance and series information is relevant for machine setup? The insert is supplied in tolerance class M and forms part of the Tiger‑tec Gold series, supporting reproducible seating in standard toolholders. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen The Walter AG (brand: Walter Tools) is a leading manufacturer of precision tools and is part of the Sandvik Group. Protected trademarks and product names are the property of their respective owners and are mentioned for explanatory purposes only. There is no connection between our company and the mentioned brands. The offered article is original, brand‑new goods from the manufacturer.
Fragen zu diesen Produkten??
Mit mehr als 30 Jahren Erfahrung beraten wir Sie gerne persönlich.
Tel.: +49 2822 7131930
Mail: info@metav-werkzeuge.com