55mm Core Drill Ultra 35 HM Tipped 35mm Cutting Depth Quick IN Shank 18mm - C. & E. Fein GmbH
Take advantage of the combination of carbide-tipped construction, a Quick IN 18 mm shank and a compact overall length for efficient, repeatable holemaking. Order the tool directly via Metav Werkzeuge or ask the consultants for application-specific advice. Ultra 35 core drill (annular cutter) – 55 mm, 35 mm cutting depth, Quick IN 18 mm shank by Fein The Ultra 35 core drill is a carbide-tipped annular cutter engineered for fast, durable holemaking in industrial environments using a Quick IN 18 mm shank for rapid tool changes Carbide-tipped for extended tool life 55 mm diameter with 35 mm cut depth Quick IN 18 mm shank for fast changeovers Metric dimensions and high cutting performance Faster, more economical holemaking through carbide-tipped design The annular cutter combines a carbide-tipped cutting edge with a compact geometry to deliver a high rate of material removal while reducing rework. The nine cutting edges ensure a smoother chip flow and lower cutting forces compared with single-point solutions, which leads to longer tool life and fewer tool changes during production runs. For workshops seeking predictable throughput, this configuration translates into reduced machine downtime and a lower overall cost-per-hole while maintaining consistent hole quality. The carbide tipping is especially effective where abrasive wear or frequent use shortens the life of conventional cutters. Rapid set-up and secure fixation with Quick IN shank The integrated Quick IN 18 mm shank provides a positive retention fit and simplifies tool exchange on compatible machines. Quick-change capability reduces non-productive time between operations and supports high-mix, low-volume work as well as repetitive production. With an overall length of 77 mm and a defined cutting depth of 35 mm, the tool is sized for compact setups where access and clearance are limited. The standardised metric dimensions facilitate easy integration into existing tooling systems and fixtures, enabling a safe and repeatable clamping process without additional adaptors. Precision results for workshop and production use Designed as a dedicated holemaking tool, the cutter delivers clean, well-defined bore edges and consistent diameter control thanks to its geometry and cutting-edge arrangement. The 55 mm diameter is suited to common hole requirements while the annular design minimises waste by removing only the material required for the hole centre. Supplied as a single unit in a practical packaging format, the tool suits maintenance, fabrication and production environments that require a robust, ready-to-fit solution. Technical specifications follow machine compatibility checks to ensure efficient and predictable performance in everyday workshop applications. Check availability and request tailored application advice from Metav Werkzeuge for this carbide-tipped Ultra 35 annular cutter with Quick IN shank Technical data Article number: 4149702055NW SKU: 4149702055NW Manufacturer: C. & E. Fein GmbH Product type: Core drill (annular cutter) Label: Kernbohrer Ultra 35 D.55mm Quick IN FEIN Facts Diameter: 55 mm Cutting depth: 35 mm Overall length: 77 mm Cutting edges: 9 Packaging unit: 1 Special features Carbide-tipped (HM-bestückt) Quick IN shank 18 mm Highest tool life and excellent cutting performance Metric dimensions FAQ What is the cutting depth of the tool? The cutting depth is 35 mm for the Ultra 35 core drill (annular cutter) with a 55 mm diameter. Which shank system is used for clamping? The tool features a Quick IN shank with an 18 mm interface for rapid, secure clamping. How many cutting edges does the cutter have? The annular cutter is manufactured with nine cutting edges to support smooth chip formation and extended wear life. Metav IndustryLine: Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
56mm Hole Saw Ultra 35 Carbide-Tipped Quick IN Shank 35mm Cutting Depth - C. & E. Fein GmbH
Benefit from a combination of carbide-tipped durability, a quick-change Quick IN shank 18 mm, and a precise 35 mm cutting depth for reliable, high-throughput core drilling. Order the annular cutter through Metav Werkzeuge or consult the team for application advice. Fein Ultra 35 Annular Cutter D56 mm with Quick IN shank The Fein Ultra 35 annular cutter designed for rapid, precise 35 mm deep core holes in metalworking applications Carbide-tipped for extended lifetime Quick IN 18 mm shank for secure fitting 35 mm cutting depth for efficient core holes Metric dimensions and industrial quality Faster, more economical metal removal with reliable carbide tips The Fein Ultra 35 family delivers economical machining by combining an annular cutter geometry with a carbide-tipped cutting edge. This configuration removes material as a ring, which notably reduces drilling energy compared with solid twist drills and shortens cycle times. The D56 mm diameter and 35 mm cutting depth are specified for consistent hole quality in through and partial-hole tasks. The carbide tips provide wear resistance under intermittent and continuous use, which translates into fewer tool changes and lower lifetime tooling costs—a clear rational advantage for production-focused workshops. Secure, rapid tool changes that keep production running A central benefit is the Quick IN shank 18 mm, which enables secure, repeatable seating in compatible magnetic drills and arbour systems. The shank design reduces tool-change times and ensures concentricity during cutting, supporting accurate hole formation and minimising secondary machining. Improved chip evacuation and reduced heat build-up contribute to maintained edge geometry over longer runs, increasing effective tool life and helping to sustain throughput in batch and one-off work alike. This practical handling aspect supports continuity on the shop floor and fewer interruptions to the process. Robust geometry and clear compatibility for workshop use Constructed as an annular cutter with 9 cutting edges and a total length of 77 mm, the tool is suited to industrial settings where repeatable performance and metric sizing matter. The HM-equipped designation indicates hard-metal inserts that combine hardness and toughness for mixed-metal applications; the cutter performs reliably when used within its 35 mm cutting depth. Clear technical dimensions make integration into existing tool chains straightforward, while the single-piece packaging unit simplifies procurement and inventory management. The overall design balances machinability with longevity, making it a pragmatic choice for metalworking shops that prioritise predictable results. Contact Metav Werkzeuge for tailored application advice on the Fein Ultra 35 annular cutter with Quick IN shank and to enquire about compatibility with existing magnetic drilling systems. Technical data Article number: 4149702056NW Label: Kernbohrer Ultra 35 D.56mm Quick IN FEIN Manufacturer: C. & E. Fein GmbH Product type: Annular cutter UID: 4149702056NW Facts Diameter: 56 mm Overall length: 77 mm Cutting depth: 35 mm Number of cutting edges: 9 Shank: Quick IN shank 18 mm Packaging unit: 1 Special features HM-equipped (carbide-tipped) Highest service life and excellent machining performance Metric dimensions Shank execution: Quick IN FAQ How does the annular cutter compare to a twist drill for large holes? The annular cutter removes a ring of material and therefore requires less power and time than equivalent twist drills; the Ultra 35 annular cutter is designed to deliver faster core holes with consistent edge quality. Which machines are compatible with the Quick IN shank? The Quick IN shank 18 mm fits systems and magnetic drills that accept Quick IN tooling; confirmation of compatibility with a specific magnetic drill is recommended before use. Can this cutter be used on stainless or alloy steels? The cutter is HM-equipped and offers high wear resistance; it is suitable for many steels and alloy applications when used within the 35 mm cutting depth and appropriate cutting parameters. What maintenance extends the life of the cutter? Maintaining correct speeds, feed and coolant use, combined with prompt chip clearance, helps preserve the carbide tips and prolongs service life of the annular cutter. Is the cutter supplied ready to use from the packaging? The tool is supplied as a single unit with a Quick IN shank ready for installation in compatible holders or magnetic drills Manufacturer: C. & E. Fein GmbH; Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
57mm Core Drill Ultra 35 Quick IN, 35mm Cutting Depth, Carbide Tipped - C. & E. Fein GmbH
Take advantage of the combination of carbide-tipped durability, a 57 mm diameter for large cores and a Quick IN 18 mm shank for fast tool changes to keep production running smoothly; order via Metav Werkzeuge or consult our specialists for application advice. Ultra 35 Annular cutter D57 mm Quick IN (Fein) — Carbide-tipped annular cutter with Quick IN 18 mm shank Ultra 35 is an annular cutter designed for efficient drilling of large-diameter through-holes and cores in metalworking applications, offering a reliable balance of wear resistance and cutting performance Carbide-tipped design for long tool life Quick IN 18 mm shank for fast tool changes 57 mm diameter for large cores 35 mm cutting depth for precise holes High, consistent cutting performance that reduces cycle times The carbide-tipped geometry and optimized cutting profile deliver a robust compromise between tool life and metal removal rate. With nine cutting edges the cutter distributes load evenly across the tooth flanks, which reduces vibration and enables sustained feed rates. This performance profile translates directly into shorter cycle times and fewer tool changes, supporting higher throughput on magnetic drills and drilling rigs without sacrificing surface quality. Precision holemaking with predictable depth and finish A defined 35 mm cutting depth and a precisely ground cutting rim ensure consistent core length and clean hole walls, reducing secondary finishing work. The annular design removes only the material of the hole perimeter, lowering thrust forces compared with twist drills and preserving component geometry. For operations where repeatability matters, the combination of diameter control and carbide cutting edges produces reliable hole tolerances and an improved fit for subsequent assembly. Tool handling and machine compatibility for rapid set‑ups The Quick IN 18 mm shank enables rapid clamping and interchange in compatible quick-change adaptors and drill bodies, cutting set-up times on the shop floor. The relatively compact overall length supports use in confined setups while maintaining the required cutting depth. Clear, metric sizing simplifies integration into existing tooling inventories and reduces the risk of incorrect tool selection during changeovers. Robustness and economy across varied materials The cutter’s carbide tipping and robust tooth count provide high wear resistance when machining common engineering materials. The combination of geometry and construction is particularly suited to applications that demand frequent large-diameter holes with minimal downtime. By extending usable life per cutter, the tool reduces total tooling consumption and contributes to more predictable operating costs over production runs. For technical ordering and tailored application advice for this carbide-tipped annular cutter, contact Metav Werkzeuge for specialist guidance and to arrange supply: info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: 4149702057NW Product type: Annular cutter Type / model: Ultra 35 Material: Carbide-tipped Manufacturer: C. & E. Fein GmbH Facts Diameter: 57 mm Cutting depth: 35 mm Overall length: 77 mm Cutting edges: 9 Shank: Quick IN 18 mm Packaging unit: 1 Special features Quick IN shank for fast tool changes High wear resistance and long service life Metric dimensions for straightforward integration Optimised for efficient material removal and clean cores FAQ What materials is this cutter suitable for? The Ultra 35 annular cutter, carbide-tipped and with nine cutting edges, is suitable for standard engineering steels and comparable metals where an annular cutter is appropriate; material-specific performance depends on machine rigidity and cutting parameters. Which machines accept the Quick IN 18 mm shank? Machines and drill adaptors designed for Quick IN 18 mm shanks accept this cutter; compatibility should be confirmed with the drilling system manufacturer and the Ultra 35 product specification. How deep can the cutter cut in a single pass? The cutter offers a defined cutting depth of 35 mm, enabling consistent hole depth without additional plunging operations. How does the annular cutter compare to a twist drill for large holes? An annular cutter such as this one removes only the periphery of the hole, lowering thrust, improving finish and typically allowing higher feed rates than a twist drill for large diameters. Is regrinding or resharpening possible? Carbide-tipped cutters can sometimes be reconditioned depending on wear; consult tooling service guidelines and the Ultra 35 specification before proceeding with resharpening. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
58mm Core Drill Ultra 35 35mm Cutting Depth HM-Tipped Quick IN Shank 18mm - C. & E. Fein GmbH
Taking advantage of carbide-tipped construction and the Quick IN 18 mm shank, the Ultra 35 core drill delivers consistent hole quality and extended service life for production and maintenance work. Order the Ultra 35 core drill directly via Metav Werkzeuge or ask our consultants if needed. Ultra 35 core drill — carbide-tipped with Quick IN 18 mm shank Ultra 35 is a carbide-tipped core drill designed for fast, precise 58 mm-diameter holes with a 35 mm cutting depth in metric systems Carbide-tipped for long service life Quick IN shank 18 mm for fast tool changes 58 mm diameter, 35 mm effective cutting depth Durable cutting performance for demanding metalwork The core drill is fitted with carbide-tipped cutting edges that provide high wear resistance and a stable cutting geometry throughout prolonged use. With nine cutting edges, the tool maintains a consistent chip formation that reduces vibration and heat build-up. This improves tool life and keeps drilling quality high in repeated production cycles, making the cutter especially suitable for workshops that require reliable performance under heavy use. Fast tool changes and reliable mounting in workshop systems Equipped with a Quick IN shank 18 mm, the design enables rapid, secure mounting in compatible quick-change holders and hand-held machines. The standardised shank dimension simplifies tool handling in mixed-tool environments and shortens set-up times during shift changes. The metric dimensions and the compact overall length ensure compatibility with a wide range of machines while keeping the tool ready for immediate use in maintenance and installation tasks. Clean holes and efficient chip removal for smooth workflows A 35 mm cutting depth combined with the 58 mm diameter results in clean core removal when paired with appropriate backing and extraction methods. The nine cutting edges and the carbide tip deliver excellent cutting performance, reducing burring and rework. For operators unfamiliar with the technicalities, carbide-tipped means a hard-metal insert on the cutting lips that resists abrasion far better than high-speed steel, so fewer tool changes are required and productivity remains high. Application focus and practical advantages Engineered for metalworking and industrial maintenance, this core cutter excels where reliable repeatability is essential—such as electrical installation, HVAC work and structural fittings where precise, metric-sized hole patterns are used. The compact overall length and robust shank execution make the tool a practical choice for confined spaces and for rapid on-machine swaps. The construction prioritises service life and predictable results, supporting efficient production planning. Choose the FEIN Ultra 35 core drill with Quick IN shank 18 mm — contact Metav Werkzeuge at info@metav-werkzeuge.com or +49 2822 7131930 for advice and availability from Emmerich. Technical data Article number: 4149702058NW Type: Ultra 35 Label: Kernbohrer Ultra 35 D.58mm Quick IN FEIN Manufacturer: C. & E. Fein GmbH Facts Diameter: 58 mm Cutting depth: 35 mm Overall length: 77 mm Number of cutting edges: 9 Shank: Quick IN shank 18 mm Packaging unit: 1 Special features Carbide-tipped (HM) construction Quick IN shank 18 mm Metric dimensions Highest service life and excellent cutting performance FAQ What materials is the core drill suitable for? The Ultra 35 core drill with carbide-tipped edges is optimised for metalworking applications and performs well on common industrial metals when used with suitable machine settings. How deep can the tool cut in a single pass? The tool is specified for a 35 mm cutting depth, which is the effective depth for clean core removal in standard operations. Which shank system does the drill use and what does that mean for mounting? The core drill uses a Quick IN shank 18 mm, enabling quick and secure mounting in compatible quick-change holders and reducing machine downtime. How does the carbide tip affect maintenance intervals? Carbide tips increase wear resistance significantly compared with HSS, resulting in longer intervals between regrinds or replacements and more predictable tool life for series work. Is the Ultra 35 suitable for workshop and on-site machine use? Yes, the compact overall length and standardised shank make the Ultra 35 suitable for workshop machines and many on-site applications requiring metric-sized core holes; see article number 4149702058NW for reference. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
60mm Carbide Core Drill 50mm Cutting Depth Quick IN Shank 18mm - Ruko GmbH
Take advantage of the combination of solid-carbide construction, 50 mm cutting depth and the fast-changing Quick IN shank for higher throughput and reliable hole quality; order the Ruko solid-carbide annular cutter D60 mm directly via Metav Werkzeuge or consult our specialists for application advice. Ruko solid-carbide annular cutter D60 mm — 50 mm cutting depth, Quick IN shank A Ruko solid-carbide annular cutter D60 mm engineered for efficient, burr-reduced holemaking in hard and high-alloy steels, stainless materials and demanding structural applications. Solid-carbide design for long life 60 mm diameter for large holes 50 mm cutting depth for deep cuts Quick IN shank 18 mm for rapid changes Higher productivity when machining tough materials The solid-carbide annular cutter offers a clear productivity advantage when working with hard-to-cut materials. Its 60 mm diameter and 50 mm cutting depth enable single-pass holemaking in thick sections, reducing cycle times compared with conventional twist drills. The cutter’s multi-edge geometry—eight cutting edges—provides a steady cutting action with reduced radial forces, which results in cleaner holes and less need for secondary finishing. For operations that demand repeatable, precise results in rail profiles, abrasion-resistant plates or highly alloyed steels, this tool significantly shortens machining sequences. Quick shank system to minimise downtime Equipped with the Quick IN shank (18 mm), the tool is designed for fast, tool-free changeover in compatible holders and magnetic drilling units. The shank interface reduces fixture time and helps maintain concentric alignment during drilling cycles, so setups remain consistent across jobs. The combination of a Quick IN shank and solid-carbide body also improves run-out management, translating into improved hole geometry and longer cutter life. Fewer interruptions for tool changes mean a smoother production flow and better utilisation of operators and machines. Durable construction for demanding workshop environments Manufactured from solid carbide, the cutter delivers high wear resistance and thermal stability under the stresses of heavy-duty cutting. This makes it particularly suitable for materials listed in the technical data, such as Hardox/Weldox 400, various structural and cast steels, and stainless grades (V2A, V4A). The robust design reduces tool consumption and lowers the frequency of replacements, supporting predictable maintenance planning. Purchasing via Metav Werkzeuge places this component within a broader supply strategy that emphasises reliability and consistent availability, backed by an experienced partner in precision tools. Contact Metav Werkzeuge today to discuss suitability for specific machine setups or to request additional machining data; Metav’s consultants are available to advise on integration and process optimisation Technical Data Article number: 4000602664NW Manufacturer: Ruko GmbH Präzisionswerkzeuge Core specifications Type: Annular cutter (solid carbide) Diameter: 60 mm Cutting depth: 50 mm Overall length: 112 mm Cutting edges: 8 Shank: Quick IN shank 18 mm Packaging unit: 1 Materials & special features Material: Solid carbide Applications: Railway rails, Hardox, Weldox 400, structural steel, cast steel, high‑chromium stainless steel (V2A, V4A), other high-alloy steels Shank interface: Quick IN Intended for heavy-duty, single-pass holemaking FAQ Is this cutter suitable for stainless steel and high-alloy materials? The Ruko solid-carbide annular cutter D60 mm is designed to machine high-chromium stainless steels (V2A, V4A) and other high-alloy steels as listed in the specifications. Which machines are compatible with the Quick IN shank? The Quick IN shank (18 mm) fits holders and magnetic drilling units designed for Quick IN interfaces; compatibility should be confirmed with the machine’s tooling system. How does the cutter perform on abrasion-resistant steels like Hardox or Weldox? Performance on Hardox and Weldox 400 is a core application area for this cutter, where the solid-carbide construction and multi-edge geometry preserve tool life and deliver consistent hole quality. What is the typical tool life or wear behaviour? Tool life depends on workpiece material, coolant use and cutting parameters; the solid-carbide design and eight cutting edges provide enhanced wear resistance for demanding workloads. Ruko GmbH: Manufacturer/Responsible: Ruko GmbH Präzisionswerkzeuge, Robert-Bosch-Strasse 7, 71088 Holzgerlingen
60mm Core Drill HSS 30mm Cut Depth Weldon Shank - Ruko GmbH
Reliable holemaking for metalworking is achieved by combining high-performance HSS construction with a 60 mm cutting diameter and a secure Weldon shank for quick clamping; order this core drill via Metav Werkzeuge or consult our specialists for workshop-ready delivery. RUKO annular cutter D 60 mm (HSS) — 30 mm cutting depth, Weldon 19.05 mm shank The RUKO annular cutter D 60 mm HSS is a purpose-built core drill for efficient, burr-reduced holemaking in structural steel and non-ferrous metals. High-performance HSS construction 60 mm diameter for large bores 30 mm cutting depth per pass Weldon shank 19.05 mm (3/4") quick clamping Precision and performance where it counts The annular cutter is manufactured from HSS, delivering a balance of toughness and edge retention that supports demanding drilling tasks. With a 60 mm diameter and a 30 mm cutting depth per pass, the tool creates large, accurate bores with reduced material waste compared with full-bore drilling. The geometry and the 12 cutting edges reduce cutting forces and promote smooth chip evacuation; this translates into shorter cycle times and more consistent hole quality for fabricators and maintenance shops alike. Faster set-up and reliable clamping for productive workflows A Weldon shank of 19.05 mm (3/4") enables secure, repeatable clamping in compatible holders and magnetic drills, shortening changeover times and improving machine utilisation. The annular design concentrates cutting on the bore perimeter, meaning less power draw and lower heat input at the workpiece; this reduces the need for secondary finishing and helps maintain component tolerances. Compatibility with steel, cast iron and a range of non-ferrous alloys makes the cutter a versatile choice for structural, sheet and component work. Integration into workshop supply and quality assurance Sourcing the cutter through a specialist distributor supports dependable stock and technical guidance. Metav combines a wide product range with experienced advice and a transparent supply chain, helping workshops reduce supplier complexity and avoid interruptions. Choosing a well-specified annular cutter from a proven brand improves throughput and lowers rework risk, contributing to a steadier production flow and higher end-product consistency. Contact Metav Werkzeuge for tailored advice and prompt delivery of RUKO annular cutters with Weldon shanks; email info@metav-werkzeuge.com or call +49 2822 7131930 to discuss suitability for specific machines and materials. Technical data Article number: 4000602339NW Product: Annular cutter Manufacturer: Ruko GmbH Material: HSS Packaging unit: 1 Facts Diameter: 60 mm Overall length: 63 mm Cutting depth: 30 mm Cutting edges: 12 Shank size: 19.05 mm (3/4") Special features Weldon shank for quick clamping Suitable for steel, cast iron, non-ferrous metals 30 mm cutting depth per pass High-performance HSS construction FAQ What materials can be machined with this annular cutter? The RUKO annular cutter is suitable for steel, cast iron and a range of non-ferrous metals, making it versatile for structural and fabrication tasks. Which shank size is required for clamping? The tool uses a Weldon shank of 19.05 mm (3/4"), designed for holders and magnetic drills that accept Weldon-style clamping. How deep can this cutter cut in a single pass? This annular cutter has a cutting depth of 30 mm per pass, allowing efficient creation of through-holes or deep bores depending on application. How does the annular cutter compare with twist drilling for large holes? An annular cutter removes material only from the bore perimeter, reducing power draw and producing cleaner holes with less machining time than equivalent twist-drilling for large diameters. Is this product associated with a specific SKU for ordering? Yes, the product is listed under SKU 4000602339NW and is supplied by Ruko; refer to this number when enquiring or ordering. Manufacturer / Responsible: Ruko GmbH Präzisionswerkzeuge, Robert-Bosch-Strasse 7, 71088 Holzgerlingen
60mm Core Drill HSS 55mm Cut Depth Weldon Shank - Ruko GmbH
A precision solution for large-diameter holemaking: the combination of HSS construction, a 60 mm cutting diameter and a Weldon shank delivers durable performance for structural steel, cast iron and non‑ferrous metals; order directly via Metav Werkzeuge or contact our consultants for application advice. Annular Cutter D60 mm HSS, 55 mm Cutting Depth (Weldon) – Ruko The Annular Cutter D60 mm HSS is a high-performance core drill designed for efficient, low‑distortion holemaking in steelwork, cast iron and light metals, fitted with a 3/4" Weldon shank for secure machine attachment. HSS for high wear resistance 60 mm diameter for large holes 55 mm effective cutting depth Weldon 3/4" shank for secure clamping Faster, cleaner large‑hole production with proven material technology Manufactured from HSS, this annular cutter offers a balance of toughness and hardness that supports sustained cutting under load. The 60 mm diameter combined with a 55 mm cutting depth reduces the need for multiple operations when producing large clear holes in profiles and plates, enabling shorter cycle times and fewer secondary processes. The material choice means the tool tolerates intermittent impacts and higher heat levels compared with standard carbon steels, resulting in consistently clean hole boundaries and a reduced need for finishing passes. By focusing on effective, single‑pass holemaking, the cutter directly improves throughput on magnetic drills and pillar drills used in fabrication shops. Secure machine integration for repeatable hole accuracy The Weldon shank (19.05 mm / 3/4") ensures fast, reliable clamping in compatible chucks and holders; the flats accept a grub screw to prevent slippage and minimise runout. Stable fixation translates into repeatable hole quality, lower tool vibration and a reduced risk of workpiece damage during drilling. For production environments where reproducibility matters, the shank design speeds tool changes and maintains concentricity under load. The mechanical interface also simplifies automation or semi‑automated set‑ups where robust attachment and predictable performance are essential. Versatile application across metals with practical handling notes This cutter is suitable for machining steel, cast iron and assorted non‑ferrous metals, including aluminium and brass, as noted by the product specification. As an annular cutter it removes a ring of material rather than producing a full‑diameter swarf, lowering power draw and improving chip evacuation on thicker sections. For best results on thicker or structural elements, use a steady feed and an appropriate cutting fluid to support chip removal and heat control. For delicate light‑metal work, moderate spindle speeds and controlled feed will preserve surface finish while maintaining efficient penetration. Long service life through reconditioning and correct practice A further practical advantage is the resharpenable nature of HSS tooling: worn cutting lips can be reconditioned, restoring geometry and extending service life compared with many brazed or coated alternatives. Regular inspection of the cutting edges and prompt regrinding maintain hole quality and dimensional accuracy, supporting cost efficiency over multiple tool lifecycles. Combined with the secure Weldon shank interface, maintenance routines are straightforward and downtime for tool changes or reconditioning is kept to a minimum, supporting a reliable production flow. For workshop reliability and tailored application support, request the Ruko Annular Cutter through Metav Werkzeuge — Metav’s specialists in Emmerich will assist with technical matching and supply directly from stock Technical data Article number: 4000602491NW Label: Kernbohrer D.60mm HSS Schnitt‑T.55mm Weldon RUKO Manufacturer: Ruko GmbH Facts Diameter: 60 mm Overall length: 88 mm Cutting depth: 55 mm Cutting edges: 12 Shank: Weldon 19.05 mm (3/4") Packaging unit: 1 Special features Material: HSS Weldon shank for secure clamping Suitable for steel, cast iron, non‑ferrous metals Resharpenable cutting geometry FAQ What materials can this annular cutter machine? The annular cutter is suitable for machining steel, cast iron and non‑ferrous metals; the HSS construction supports routine use on structural steel and light alloys. Is the shank compatible with magnetic drills? The cutter is supplied with a Weldon shank (19.05 mm / 3/4"), designed for secure clamping in holders that accept Weldon‑style flats, commonly used on magnetic drills and pillar drill chucks. Can the cutter be resharpened? Yes, the HSS body is resharpenable; reconditioning the cutting edges restores geometry and extends service life while maintaining hole quality. What hole depth and diameter does the tool provide? The tool provides a 60 mm hole diameter with an effective cutting depth of 55 mm, suitable for many plate and profile applications where a single‑pass hole is required. Is a coating applied to improve wear resistance? No coating is specified for this tool; wear performance relies on the HSS material and correct machining practice, including suitable coolant and feeds. Manufacturer/Responsible: Ruko GmbH Präzisionswerkzeuge, Robert‑Bosch‑Strasse 7, 71088 Holzgerlingen
60mm Core Drill Ultra 35 35mm Cutting Depth, Solid Carbide Tips Quick IN Shaft 18mm - C. & E. Fein GmbH
The combination of HM‑tipped cutting geometry, an 18 mm Quick IN shank and a 35 mm effective cutting depth ensures efficient, repeatable core drilling and extended tool life; order directly via Metav Werkzeuge or consult the Metav team for application support. FEIN Ultra 35 Core Drill D60 mm – HM‑tipped, Quick IN shank The FEIN Ultra 35 core drill for precision holemaking in metal, featuring an 18 mm Quick IN shank and a 35 mm cutting depth for rapid, repeatable core extraction HM‑tipped for extended service life 18 mm Quick IN shank for fast tool changes 35 mm cutting depth for through and shallow cores 60 mm diameter with 9 cutting edges for clean chips High‑performance drilling that reduces cycle time The HM‑tipped design delivers high wear resistance and consistent cutting performance, translating into fewer tool changes and lower downtime. With a 9‑edge cutting geometry, the cutter maintains steady feed forces and produces stable chip flow, which improves surface finish and reduces rework. The 35 mm cutting depth, combined with the specified 60 mm diameter, is engineered for efficient core removal in common metalworking tasks, so production lines benefit from faster holemaking and predictable throughput. Fast tool changes and secure machine interface Equipped with an 18 mm Quick IN shank, the core drill enables swift, tool‑free insertion and removal when used with compatible holders, reducing non‑productive time between operations. The Quick IN system also ensures axial and radial stability during drilling, which supports accurate hole position and concentricity. For workshops seeking modular setups and minimal fixture complexity, this shank design supports seamless integration into standard magnetic drills and compatible holders. Practical advantages for workshop use and maintenance The robust construction and HM‑tipped cutting edges mean longer service intervals, which lowers consumable costs over time and simplifies inventory management. The drill’s overall length of 77 mm and metric dimensions make it straightforward to select correct guards and depth stops. Maintenance is basic: regular inspection of the cutting edges and correct mounting in a Quick IN holder guarantee consistent results. For operators less familiar with carbide tooling, HM‑tipped refers to hard‑metal (tungsten carbide) inserts brazed or mounted to the body for superior wear resistance compared with high‑speed steel. For application advice or to request FEIN Ultra 35 core drills with Quick IN shanks, contact Metav Werkzeuge GmbH via info@metav-werkzeuge.com or call +49 2822 7131930 — Metav’s specialists will recommend the correct holder and process parameters for the intended material and machine. Technical data Article number: 4149702060NW Product: Core drill, Ultra 35 Manufacturer: C. & E. Fein GmbH Facts Diameter: 60 mm Total length: 77 mm Cutting depth: 35 mm Cutting edges: 9 Shank: Quick IN, 18 mm Packaging unit: 1 Special features HM‑tipped construction Quick IN shank 18 mm Metric dimensions High service life and excellent machining performance FAQ What materials is the FEIN Ultra 35 core drill suitable for? The FEIN Ultra 35 core drill (SKU 4149702060NW) is designed for use with common ferrous and non‑ferrous metals where carbide‑tipped tooling is appropriate; selection of speeds and feeds should follow machine and material recommendations. How does the Quick IN shank benefit workshop workflows? The 18 mm Quick IN shank on the FEIN Ultra 35 core drill allows rapid tool changes and secure mounting, reducing non‑productive time when switching cutters or during maintenance intervals. What maintenance is required to maximise tool life? Regular inspection of the HM‑tipped cutting edges and ensuring correct seating in a compatible Quick IN holder will maximise the FEIN Ultra 35 core drill’s service life and maintain drilling accuracy. Is the 35 mm cutting depth sufficient for through holes? A 35 mm cutting depth suits many shallow and through‑hole applications when paired with the correct pilot or backing plate; for deeper cores, staging or specialised tooling may be necessary. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
70mm Core Drill Solid Carbide 50mm Cutting Depth Quick IN Shank - Ruko GmbH
Take advantage of a combination of material-specific performance and quick tool change for uninterrupted production: the solid-carbide design and 50 mm cutting depth enable accurate core drilling in demanding steels, while the Quick IN 18 mm shank reduces setup time. Order directly via Metav Werkzeuge or contact our technical consultants for application advice. Core Drill D70 mm (Solid Carbide) – 50 mm Cutting Depth, RUKO A Core Drill D70 mm (Solid Carbide) designed for reliable core drilling in steel, cast iron and high‑alloy materials for industrial and workshop use Solid-carbide for heavy-duty use 50 mm cutting depth for deep cores Quick IN 18 mm shank for fast mounting Suitable for steel, cast iron and high‑alloy steels High-performance cutting for demanding materials The solid carbide body and eight cutting edges deliver stability and consistent chip formation when working with tough workpiece materials. Solid carbide offers high rigidity compared with tool-steel alternatives, which reduces vibration and supports precise bore geometry; this makes the tool particularly effective when accuracy and repeatability are required. The combination of a 70 mm diameter and a 50 mm cutting depth enables the removal of substantial core sections without compromising surface finish, translating into fewer rework cycles and more predictable machining times. Reduce machine downtime with secure, fast mounting Equipped with the Quick IN 18 mm shank, the tool is intended for rapid clamping and repeatable concentricity in suitable holders. The Quick IN interface simplifies tool changes and shortens fixture time, supporting higher machine availability and more efficient shift planning. For production environments where changeover speed is a factor, the quick‑release shank reduces non‑productive time while maintaining a secure connection that preserves concentricity during high‑torque operations. Engineered for rail, abrasion‑resistant and stainless steels Designed specifically for heavy applications, the core drill is suitable for rail tracks and abrasion‑resistant steels such as Hardox or Weldox 400, as well as general steel, cast steel and high‑chromium stainless grades (V2A, V4A). The cutting geometry and carbide grade are selected to withstand the mechanical demands of these materials, offering a balance of edge strength and wear resistance. For machining tasks that involve frequent contact with high‑strength or work‑hardened surfaces, this design reduces the risk of premature tool wear and helps maintain hole integrity. Professional workshop reliability and application guidance Delivered as a single unit and intended for professional usage, the tool supports both one‑off repair work and series production. The robust construction and targeted application range make it a practical choice for maintenance departments, fabrication shops and industrial workshops that require dependable core drilling performance. For customers needing guidance on holder compatibility or machining parameters, technical consultation is available to ensure correct integration into existing machining setups. For heavy‑duty core drilling tasks choose RUKO’s proven tooling and order via Metav Werkzeuge; for specific application advice contact our technical team at info@metav-werkzeuge.com or by phone on +49 2822 7131930 Technical data Article number: 4000602669NW Product type: Core drill Manufacturer: Ruko GmbH Präzisionswerkzeuge SKU: 4000602669NW Data Diameter: 70 mm Overall length: 112 mm Cutting depth: 50 mm Cutting edges: 8 Packaging unit: 1 Special features Material: Solid carbide Shank: Quick IN shank 18 mm Application: Rail tracks Application: Hardox / Weldox 400 steels Application: Steel and cast steel Application: High‑chromium steels (V2A, V4A) FAQ Which materials can this core drill machine? The Core Drill D70 mm (solid carbide) is designed for heavy‑duty materials including rail tracks, Hardox/Weldox 400, general steel, cast steel and high‑chromium stainless steels such as V2A and V4A. What is the effective cutting depth? The tool provides a 50 mm cutting depth, suitable for producing deep cores in thick workpieces. Which shank is required for mounting? A Quick IN holder compatible with an 18 mm Quick IN shank is required for secure and repeatable mounting of the core drill. Is this tool suitable for production environments? Yes, the solid‑carbide construction and Quick IN interface make the drill appropriate for both maintenance work and serial production where durability and fast changeovers are needed. How many cutting edges does the tool have and why does that matter? The tool features eight cutting edges, which contribute to stable cutting behaviour, improved surface finish and balanced load distribution during core removal. Manufacturer/Responsible: Ruko GmbH Präzisionswerkzeuge, Robert‑Bosch‑Strasse 7, 71088 Holzgerlingen
80mm Core Drill Solid Carbide 50mm Cutting Depth Quick IN Shank - Ruko GmbH
Take advantage of the solid carbide construction, 80 mm diameter and Quick IN shank for reliable performance in heavy-duty steel applications; order the Ruko core drill directly via Metav Werkzeuge or contact their consultants for tailored application support. Ruko Core Drill D 80 mm – Solid Carbide, 50 mm Cutting Depth The Ruko Core Drill D 80 mm is a solid carbide core drill engineered for demanding drilling tasks in rails, Hardox/Weldox 400 and a wide range of alloyed steels, providing robust cutting performance and fast tool changes. Solid carbide construction 50 mm cutting depth Quick IN 18 mm shank For rails and wear-resistant steels High-performance cutting for demanding materials The solid carbide design delivers high wear resistance and consistent cutting quality when machining hard and alloyed materials. With 10 cutting edges, the tool achieves aggressive material removal while maintaining hole accuracy. Its suitability for rails, Hardox/Weldox 400 and high-chrome stainless steels (V2A/V4A) makes it a reliable choice where conventional drills wear quickly. The robust geometry reduces vibration and heat build-up, which in turn extends service life and lowers the frequency of tool changes, improving overall productivity. Precision and stability with fast changeover An 80 mm diameter and 50 mm cutting depth combine for clean core removal and predictable hole dimensions. The Quick IN 18 mm shank enables rapid clamping and tool exchange on compatible holders, cutting downtime in workshops that run multiple operations. The compact 112 mm overall length supports better axial stability than longer tools, reducing runout and the risk of drift in thick or constrained workpieces. For machine setups where concentricity and repeatability matter, this geometry ensures consistent hole quality across production runs. Durable economy and workshop integration Constructed from solid carbide, the core drill resists abrasive wear and thermal stress characteristic of tough steelwork, offering a longer life than HSS alternatives in comparable tasks. That extended lifetime translates into lower tool consumption and fewer interruptions for replacement, contributing to a favourable cost-per-hole ratio. For enquiries about machine compatibility or feed and speed recommendations, Metav’s technical team is available to advise on integrating the tool into existing workflows and selecting the correct holders and coolant strategies. For heavy-duty steel drilling select the Ruko core drill and contact Metav Werkzeuge in Emmerich for supply and application consulting — email info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: 4000602672NW Name: Ruko Core Drill D 80 mm Brand: Ruko GmbH Product type: Core drill Material: Solid carbide Packaging unit: 1 Shank execution: Quick IN-Shaft 18 mm Core measurements Diameter: 80 mm Overall length: 112 mm Cutting depth: 50 mm Cutting edges: 10 Shank dimension: 18 mm Applications & special features Suitable for rails Suitable for Hardox/Weldox 400 Suitable for steel and cast steel Suitable for high-chrome steels V2A/V4A and higher alloyed steels Quick IN shank for fast tool changes FAQ What materials is the core drill suitable for? The Ruko core drill is designed for heavy-duty applications including rails, Hardox/Weldox 400, general steel, cast steel and high-chrome stainless steels such as V2A and V4A. What is the maximum cutting depth of the tool? The core drill offers a cutting depth of 50 mm for clean core extraction and controlled hole formation. Which shank type is used and how does it help? The tool features a Quick IN 18 mm shank to allow rapid clamping and fast changeovers on compatible holders, improving workshop efficiency. How many cutting edges does the drill have and why does that matter? With 10 cutting edges, the drill balances aggressive material removal with stability and reduced vibration, enhancing hole quality and tool life. Is the tool suitable for use with coolant or specific machines? The Ruko core drill can be used in heavy-duty drilling rigs and machine centres; Metav Werkzeuge can advise on coolant strategy and machine suitability for the intended application. Manufacturer/Responsible: Ruko GmbH Präzisionswerkzeuge, Robert-Bosch-Strasse 7, 71088 Holzgerlingen
Fragen zu diesen Produkten??
Mit mehr als 30 Jahren Erfahrung beraten wir Sie gerne persönlich.
Tel.: +49 2822 7131930
Mail: info@metav-werkzeuge.com