200mm Rectangular HSS-EW9Co10 Ground Hardened Bar 65-69 HRC, h13 Tolerance - Werner Wilke Zerspanungstechnik GmbH
Take advantage of the combination of high hardness 65–69 HRC, a HSS-EW9Co10 alloy with 10% cobalt, and precise dimensional control for consistent turning and finishing results; order directly via Metav Werkzeuge or ask the consultants for application advice Turning blank DIN 4964 Form D — rectangular 25 x 6 mm, HSS-EW9Co10 (WILKE) The Turning blank DIN 4964 Form D is a rectangular precision bar intended for demanding turning and finishing tasks in toolrooms and small-batch production HSS-EW9Co10 with 10% cobalt content Rectangular Form D to DIN 4964 Hardened and finish-ground, 65–69 HRC Cross-section 25 x 6 mm, length 200 mm Durable hardness for repeatable, precision work The use of HSS-EW9Co10 and a hardness of 65–69 HRC delivers a turning blank that resists deformation during clamping and post-machining operations. Such elevated hardness reduces the risk of work-hardening under pressure and maintains geometric stability during light rework or finishing. The result is consistent dimensional accuracy across batches and fewer set-up checks, which supports efficient small-series production and predictable downstream processes. Alloy and performance: why 10% cobalt matters The 10% cobalt content in the high-speed steel matrix increases red hardness and edge retention under thermal stress. This material composition enables higher cutting temperatures without rapid softening, making the bar well suited for precision turning where sharp, stable edges are required after finishing passes. In practice, this means longer intervals between regrinding and a better surface integrity on turned components when using appropriate tooling and feeds. Accurate tolerances for easier clamping and finishing Dimensional control is built into the product: cross-section tolerance h13 and a length tolerance of ±2 mm allow reliable fixturing and repeatable set-ups. The blank is supplied hardened, tempered and finish-ground, with straight, unground ends that facilitate secure clamping or custom facing prior to final machining. These attributes reduce adjustment time on the lathe and simplify quality checks during first-off inspections. Practical integration into workshop workflows Supplied as a single unit and conforming to DIN 4964, this rectangular bar is straightforward to store and handle in a workshop environment. The finish-ground condition minimises immediate preparatory machining, while the unground ends allow tailored end-processing to match specific chucking or fixture systems. Technical data and the SKU are available for ordering and inventory management, and documentation can be provided to support quality records and traceability. Contact Metav Werkzeuge for tailored advice on integrating WILKE turning blanks into production; call +49 2822 7131930 or email info@metav-werkzeuge.com Technical data Article number: 4118420148NW Product type: Turning blank Designation: Turning blank DIN 4964 Form D (rectangular) WILKE Manufacturer: Werner Wilke Zerspanungstechnik GmbH Dimensions & measurements Cross-section: 25 x 6 mm Length: 200 mm Cross-section tolerance: h13 Length tolerance: +/- 2 mm Hardness: 65–69 HRC Cobalt content: 10% Material & features Material: HSS-EW9Co10 Form: Rectangular (Form D) Surface condition: Hardened, tempered and finish-ground Ends: Straight, unground Material number: 1.3207 Packaging unit: 1 FAQ What hardness can be expected from this turning blank? The turning blank is supplied hardened to 65–69 HRC, providing a stable, wear-resistant substrate for finishing and light regrinding. Which alloy is used and why is it chosen? Manufactured from HSS-EW9Co10 with 10% cobalt (Werkstoffnummer 1.3207), the material offers improved red hardness and edge retention for demanding turning tasks. What dimensional tolerances apply to the cross-section and length? Cross-section tolerance is h13; length tolerance is ±2 mm, supporting predictable clamping and repeatable set-ups. Are the ends of the blank finish-ground? The blank is finish-ground along its length but supplied with straight, unground ends to allow custom facing or chucking preparation. How is the product supplied for inventory and ordering? The product is supplied in packaging unit 1 and can be referenced by SKU 4118420148NW for ordering and stock management. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
200mm Rectangular HSS-EW9Co10 Hardened Ground Bar 20 x 10 h13, 65-69 HRC - Werner Wilke Zerspanungstechnik GmbH
Benefit from a wear‑resistant high‑speed steel blank with 10% cobalt and a hardened surface of 65–69 HRC for stable toolholding and long service intervals; the precise 20 x 10 mm cross‑section with h13 tolerance and a 200 mm length (±2 mm) supports consistent production results. Order the turning blank directly via Metav Werkzeuge or consult our specialists for application advice. Turning blank DIN 4964, Form D — HSS‑E W9 Co10 rectangular bar, 20 x 10 x 200 mm A turning blank DIN 4964 Form D manufactured from high‑speed steel HSS‑E W9 Co10, hardened, tempered and finish‑ground for precision lathe and workshop applications. HSS with 10% cobalt for wear resistance Hardened to 65–69 HRC for long tool life Rectangular 20 x 10 mm cross‑section h13 Length 200 mm with ±2 mm length tolerance Durable material and heat treatment for dependable machining results The use of HSS‑E W9 Co10 with a 10% cobalt content provides improved red hardness and abrasion resistance compared with conventional high‑speed steels; this translates into more consistent cutting behaviour under elevated temperatures and extended service intervals. The rod is hardened, tempered and finish‑ground, which means the bar arrives dimensionally stable and with a tempered microstructure that preserves edge integrity during turning or tool manufacture. This combination reduces the frequency of replacement and supports predictable tool life in serial operations. Precise dimensions that simplify setup and enhance repeatability A precisely finished 20 x 10 mm rectangular section with h13 cross‑section tolerance and a length of 200 mm (±2 mm) provides reliable fitment in standard clamping systems and fixtures. The h13 grade indicates a controlled manufacturing deviation compatible with many industrial setups; fewer manual adjustments are required and repeatability across batches is improved. Straight, unground ends allow for secure clamping while the finish grinding of the length ensures lateral stability during rotation, helping to maintain concentricity and surface quality on turned components. Conformity to standards and traceable material identity Manufactured to DIN 4964 and referenced to material number 1.3207, the bar meets common industrial expectations for turning blanks and high‑speed steel grades. The declared hardness of 65–69 HRC and the explicitly stated 10% cobalt content provide verifiable parameters for process planning. Clear material identification and standard conformity simplify quality documentation and support decision‑making when integrating the blanks into production chains or procurement records. Practical advantages for workshops and small series production As a pre‑finished rectangular turning bar, the component reduces in‑house preparation time: being finish‑ground and heat‑treated means fewer process steps before forming final cutting edges or workpieces. The material’s elevated hot hardness benefits applications that generate substantial cutting heat or require sustained cutting performance. For operations focused on reproducibility and low downtime, the blank’s dimensional consistency and mechanical properties contribute directly to predictable throughput and reduced scrap rates. For ordering and technical assistance regarding this hardened HSS turning blank, contact Metav Werkzeuge — the experienced precision partner in Emmerich — via e‑mail at info@metav-werkzeuge.com or by phone at +49 2822 7131930 to discuss suitability for specific turning tasks or to request further technical documentation Technical Data Article number: 4118420135NW Product type: Turning blank (Form D) Standard: DIN 4964 Material: HSS‑E W9 Co10 (1.3207) Hardness: 65–69 HRC Data Cross‑section: 20 x 10 mm (rectangular) Length: 200 mm Cross‑section tolerance: h13 Length tolerance: ±2 mm Cobalt content: 10% Special features Hardened, tempered and finish‑ground Ends straight and unground Querschnitt finished for reduced setup Packaging unit: 1 FAQ What is the primary material of the turning blank and what does it mean for machining performance? The turning blank is made from HSS‑E W9 Co10 (material number 1.3207); the high‑speed steel with 10% cobalt offers enhanced hot hardness and wear resistance, which improves tool life under demanding cutting conditions. Which standards and tolerances apply to this rectangular bar? The bar is produced to DIN 4964 with a rectangular 20 x 10 mm section and h13 cross‑section tolerance; the length is 200 mm with a length tolerance of ±2 mm. Is the blank ready to be clamped and machined immediately? Yes — the bar is hardened, tempered and finish‑ground, so it arrives with stable dimensions suitable for clamping; note that the ends are straight but unground. How does the declared hardness affect finishing processes? A hardness of 65–69 HRC indicates a high resistance to deformation; this supports stable cutting performance and longer service intervals but may require appropriate cutting geometries and tool materials for finishing operations. Can material traceability be confirmed for procurement records? Material identification is given as 1.3207 and the grade HSS‑E W9 Co10, which supports traceability and quality documentation for procurement and production control. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
200mm Round Bar HSS-EW9Co10 10% Cobalt Hardened 65-69 HRC h8 Tolerance, DIN 4964 Form A - Werner Wilke Zerspanungstechnik GmbH
Take advantage of a hardened, HSS-EW9Co10 turning blank with controlled tolerances and a precision finish for reliable batch production. Order the component via Metav Werkzeuge or consult our procurement team for tailored supply and stocking advice. Wilke Turning Blank DIN 4964 Form A (HSS-EW9Co10, Ø 18 mm, L 200 mm) Wilke Turning Blank DIN 4964 Form A is a hardened, precision-ground round bar designed for machining centres and toolrooms where repeatable concentricity and wear resistance are essential HSS-EW9Co10 with 10% cobalt Hardened to 65–69 HRC Precision-ground round bar, DIN 4964 Form A Diameter tolerance h8, length tolerance ±2 mm Outstanding material performance for hot cutting and wear resistance Manufactured from HSS-EW9Co10, the blank combines high-speed steel chemistry with 10% cobalt to boost hot hardness and abrasion resistance during indexed or continuous cutting. The material's thermal stability reduces flank wear at elevated temperatures, which translates into longer tool life and fewer regrinds. The bar is hardened to 65–69 HRC, ensuring structural stability for demanding turning operations while maintaining machinability for subsequent finishing steps. Predictable dimensions that reduce setup time and rework With a nominal Ø 18 mm and L 200 mm, the component is finished to DIN 4964 Form A with diameter tolerance h8 and length tolerance ±2 mm, supporting repeatable clamping and consistent run-out in chucks and collets. The blank is precision-ground so concentricity is reliable from piece to piece; ends are straight and supplied unground for easy datum setting. These measured characteristics lower setup overhead and reduce scrap, making the blank suitable for small-batch production and prototype runs. Practical workshop benefits and application guidance Identified by material number 1.3207, the round bar is tempered, finished and supplied ready for immediate turning or further toolmaking processes. The combination of hardness and cobalt content makes the blank suitable for components that require dimensional stability and wear resistance, especially in tool and die, valve and small-engine parts production. The straight, unground ends simplify fixturing, while the precision-ground shaft minimises the need for pre-machining, improving throughput in busy workshops. For dependable supply of Wilke turning blanks and expert procurement support, contact Metav Werkzeuge for stock availability and ordering guidance via info@metav-werkzeuge.com or by phone on +49 2822 7131930 Technical Data Article number: 4118401185NW Product type: Turning blank Manufacturer: Werner Wilke Zerspanungstechnik GmbH Numerical data Diameter: 18 mm Length: 200 mm Hardness: 65–69 HRC Cobalt content: 10% Diameter tolerance: h8 Length tolerance: ±2 mm Material number: 1.3207 Special features Material: HSS-EW9Co10 Standard: DIN 4964 Form A (round) Supplied hardened, tempered and finish-ground Ends straight and unground Tolerances for precision machining FAQ What material is the blank made from and what are its benefits? The blank is manufactured from HSS-EW9Co10 (material number 1.3207), offering improved hot hardness and wear resistance thanks to its 10% cobalt content; this makes the Wilke turning blank suitable for demanding machining tasks. What are the exact dimensions and tolerances of the bar? The turning blank has a nominal Ø 18 mm and L 200 mm with diameter tolerance h8 and length tolerance ±2 mm, supplied finish-ground for predictable clamping and concentricity. Is the blank ready for immediate machining? Yes, the bar is delivered hardened, tempered and finish-ground, so the Wilke turning blank can be used directly for turning or further toolmaking without preliminary heat treatment. Which applications are appropriate for this turning blank? The blank is intended for precision turning and small-series component manufacture where high wear resistance and dimensional stability are required, for example in toolmaking and mechanical parts production. How does the hardness affect processing and tool choice? With a hardness of 65–69 HRC, the blank retains form stability under load; carbide tooling and appropriate cutting data are recommended when machining this grade to achieve optimal surface quality and tool life. Manufacturer: Werner Wilke Zerspanungstechnik GmbH; Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
200mm Round Bar HSS-EW9Co10 65-69 HRC, Diameter 12mm h8, +/-2mm Length Tolerance - Werner Wilke Zerspanungstechnik GmbH
Take advantage of a hardened, finish‑ground round blank in HSS‑EW9Co10 for consistent machining results; its 65–69 HRC hardness and h8 diameter tolerance support precision turning and reduce rework. Order directly via Metav Werkzeuge or ask their consultants for application guidance and supply options. Turned blank DIN 4964 Form A Ø 12 mm — HSS‑EW9Co10 (1.3207) by Werner Wilke The Turned blank DIN 4964 Form A Ø 12 mm HSS‑EW9Co10 is a hardened, finish‑ground round blank intended for precision turning and tooling applications in industrial workshops and toolrooms HSS‑EW9Co10 with 10% cobalt for high toughness Hardened to 65–69 HRC for wear resistance Diameter tolerance h8 for precision fit Length 200 mm, straight unground ends Hardness and material composition that improve process stability The blank is manufactured in HSS‑EW9Co10 (material number 1.3207) and contains approximately 10% cobalt, which increases hot hardness and toughness compared with standard high‑speed steels. The specified 65–69 HRC hardness ensures sustained wear resistance under heavy cutting and repeated cycling. For production environments this combination of material and hardness reduces tool‑related variation and extends service intervals, helping to keep turning processes predictable and economical. Tight tolerances for repeatable assembly and clamping A controlled diameter tolerance h8 and a length tolerance of ±2 mm deliver repeatability when mounting or gaging stock. With a nominal Ø 12 mm and a length of 200 mm, the rod suits collet, chuck or bar‑feed set‑ups that require accurate concentricity. These dimensional guarantees cut down on set‑up time and part rejection, supporting smoother production flow where interchangeability and predictable run‑out are essential. Production finish that minimises preparation work Supplied hardened, tempered and finish‑ground, the blank offers a machining‑ready surface for turning operations. The ends are supplied straight and unground, which permits secure clamping without altering the precision ground running surface. This manufacturing state reduces the need for additional grinding or heat treatment before use, so workshop throughput is improved and initial processing steps are minimised. Practical suitability and handling considerations The compact turning blank is suitable for a wide range of precision turning tasks in toolrooms and component manufacture where high wear resistance is required. The finish‑ground body aids concentricity and surface quality, while the unground ends accommodate standard clamping systems. For specific cutting data, workpiece materials or batch requirements, technical consultation is recommended to match the blank’s properties to the intended process. Contact Metav Werkzeuge today to discuss supply quantities of HSS‑EW9Co10 turning blanks from Emmerich and to obtain tailored technical advice for your application Technical data Article number / SKU: 4118401130NW Product type: Turning blank Manufacturer: Werner Wilke Zerspanungstechnik GmbH Data Diameter: 12 mm Length: 200 mm Hardness: 65–69 HRC Cobalt content: 10 % Length tolerance: ±2 mm Diameter tolerance: h8 Special features Material: HSS‑EW9Co10 (Werkstoff 1.3207) Standard: DIN 4964, Form A Condition: hardened, tempered and finish‑ground Ends: straight and unground FAQ What material is this blank made from and why is it chosen? The blank is manufactured from HSS‑EW9Co10 (1.3207); this grade with about 10% cobalt provides enhanced hot hardness and toughness compared with conventional high‑speed steels, making it suitable for demanding turning tasks. What tolerances and dimensions can be expected for this product? The turning blank has a nominal Ø 12 mm, length 200 mm, with diameter tolerance h8 and a length tolerance of ±2 mm, ensuring precise fit and repeatable clamping. Is the blank ready for immediate machining straight from delivery? Yes; the body is finish‑ground and hardened, while the ends are supplied straight and unground, which allows secure clamping and reduces preparatory work before turning operations. Which standard does the blank conform to and what does that imply? The blank complies with DIN 4964 Form A, indicating a round, standardised supply form for turning blanks that supports consistent dimensions and interchangeability in production environments. Can this blank be used for high‑temperature cutting conditions? The HSS‑EW9Co10 composition and the 65–69 HRC hardness improve performance at elevated temperatures compared with non‑cobalt HSS grades; for precise cutting parameters, consult technical data or Metav Werkzeuge’s specialists. Manufacturer: Werner Wilke Zerspanungstechnik GmbH; Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
200mm Round HSS-EW9Co10 Turned Bar 65-69 HRC, h8 Diameter Tolerance - Werner Wilke Zerspanungstechnik GmbH
Take advantage of a hardened, ground high‑speed steel blank for consistent tool life and reduced setup times; the combination of HSS‑EW9Co10 material and a tight h8 diameter tolerance ensures reliable concentricity and repeatable clamping. Order via Metav Werkzeuge or consult Metav’s technical advisors for specification matching and delivery. Turning blank DIN 4964 Form A — Ø14 mm, HSS‑EW9Co10, hardened 65–69 HRC (WILKE) The Turning blank DIN 4964 Form A is a round, hardened and ground bar in HSS‑EW9Co10, designed for precision turning and small‑batch component manufacture in tool rooms and specialised workshops. HSS‑EW9Co10 with 10% cobalt Hardened and tempered, ground finish Diameter Ø14 mm, tolerance h8 Length 200 mm, length tolerance ±2 mm Consistent cutting performance from high‑speed steel with cobalt The bar is made of HSS‑EW9Co10, a high‑speed steel alloy that contains 10% cobalt, which increases hot hardness and wear resistance compared with conventional grades. With a hardness of 65–69 HRC, the material provides a stable cutting edge under intermittent high loads and improves tool life where repeated regrinding or finishing is required. This results in fewer interruptions for rework and a predictable lifetime profile for blanks used in precision turning and toolmaking. Tight dimensions to reduce set‑up and improve concentricity A nominal diameter of Ø14 mm combined with h8 diameter tolerance and a length of 200 mm (length tolerance ±2 mm) gives a consistent datum for chucking and collet gripping. The straight, unground ends facilitate secure seating while the ground outer surface ensures good concentricity for finishing operations. These dimensional assurances translate into shorter machine set‑up times and more predictable runout behaviour when producing cylindrical components or shafts. Ready for precision machining and standardised workflows Conforming to DIN 4964 Form A, the round blank arrives hardened and ground, making it suitable for immediate integration into established production flows without additional pre‑treatment. The material number 1.3207 identifies the grade for documentation and process planning, while the nominal hardness and cobalt content support higher cutting speeds and consistent finishing. The blank is aimed at precision workshops, toolmakers and manufacturers of small turned parts who require standardised, high‑quality starting stock from a reliable supplier For specification advice, availability and to arrange delivery from Metav Werkzeuge, contact Metav Werkzeuge GmbH in Emmerich by phone +49 2822 7131930 or email info@metav-werkzeuge.com — Metav’s advisors will assist with technical fitment and order processing. Technical data Article number: 4118401144NW Product type: Turning blank Manufacturer: Werner Wilke Zerspanungstechnik GmbH Facts Material: HSS‑EW9Co10 Material number: 1.3207 Standard: DIN 4964 Form: A Diameter: Ø14 mm Diameter tolerance: h8 Length L: 200 mm Length tolerance: ±2 mm Hardness: 65–69 HRC Cobalt content: 10% Special features Hardened, tempered and finish‑ground Ends straight and unground Ready for precision turning and toolmaking Conforms to DIN 4964 Form A FAQ What alloy is used for this turning blank and why is it chosen? The turning blank is produced from HSS‑EW9Co10 (material number 1.3207); the 10% cobalt content improves hot hardness and wear resistance, making the blank suitable for high‑precision and high‑stress turning applications. Is the blank supplied ready for machining or is additional heat treatment required? The Turning blank DIN 4964 Form A is supplied hardened and ground, ready for immediate machining operations without further heat treatment. Which dimensional tolerances are guaranteed for the round bar? The bar is specified as Ø14 mm with h8 diameter tolerance and a length of 200 mm with a length tolerance of ±2 mm, providing consistent datum points for clamping and finishing. Can this blank be used for toolmaking and small‑series production? Yes; the material properties, 65–69 HRC hardness and finish grinding make the blank well suited to toolmaking, prototype components and small‑series turned parts. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
200mm Square Bar Form B Hardened Ground 65-69 HRC HSS-EW9Co10, h13 Tolerance +/-2 mm - Werner Wilke Zerspanungstechnik GmbH
Take advantage of a robust, wear‑resistant turning blank that combines HSS with 10% cobalt and a 65–69 HRC heat treatment for longer tool life and consistent machining results; order directly via Metav Werkzeuge or consult our specialists for application advice. Turning blank DIN 4964 — Form B, square 18 x 18 mm (HSS‑EW9Co10) by Werner Wilke A turning blank for precision bar work and small series turning, supplied as a square blank in Form B to DIN 4964 for immediate use in machining centres and toolmaking. HSS‑EW9Co10 with 10% cobalt for increased wear resistance Hardened 65–69 HRC, finish‑ground for repeatable accuracy Square profile 18 x 18 mm with tolerance h13 Length 200 mm with length tolerance ±2 mm Precision and predictable machining for repeatable components The blank is manufactured from HSS‑EW9Co10, a high‑speed steel alloy enriched with 10% cobalt, optimised for high thermal stability and abrasion resistance. The 65–69 HRC hardening and subsequent finish‑ground condition ensure a uniform surface and consistent concentricity, reducing setup variation and trial cuts. For production environments where repeatability matters, this material and heat treatment lower tool change frequency and maintain dimensional integrity across batches. Material choice that extends service intervals and performance Selecting a turning blank in HSS‑EW9Co10 provides higher red hardness compared with conventional HSS grades; the added cobalt stabilises carbide phases at elevated temperatures, which translates to slower flank wear and better edge retention. For applications involving interrupted cuts or harder steels, the 10% cobalt content supports longer runtimes and fewer regrinds, therefore improving overall throughput and reducing indirect machining costs. Dimensional reliability to integrate into tight workflows The square cross‑section of 18 x 18 mm held to tolerance h13, together with a length of 200 mm and a length tolerance of ±2 mm, enables predictable clamping and minimal repositioning. Finished ends are supplied straight and unground, allowing flexible fixturing or a final customer‑side facing operation. Conformance to DIN 4964, Form B simplifies specification management and ensures compatibility with standard fixtures and chucks used in small‑part turning. Ready for production and easy handling on the shopfloor Supplied as a single, factory‑prepared blank, the component is hardened, tempered and finish‑ground, making it suitable for immediate integration into toolmaking, prototyping or short production runs. The combination of material specification and geometric tolerances reduces preparatory steps and enables engineers to focus on cutting parameters rather than corrective setup—helping maintain steady cycle times and predictable surface finish results. Contact Metav Werkzeuge today to discuss how the Werner Wilke turning blank (HSS‑EW9Co10, 18 x 18 mm, L 200 mm, SKU 4118415185NW) can be specified for current projects or to request further technical clarification — call +49 2822 7131930 or e‑mail info@metav-werkzeuge.com Technical Data Article number: 4118415185NW Standard: DIN 4964 Product type: Turning blank (Form B) Brand: Werner Wilke Zerspanungstechnik GmbH Material: HSS‑EW9Co10 Material number: 1.3207 Cross-section: 18 x 18 mm Total length: 200 mm Hardness: 65–69 HRC Cross-section tolerance: h13 Length tolerance: ±2 mm Cobalt content: 10 % Ends: straight and unground Surface: finish‑ground Packaging unit: 1 Facts Length: 200 mm Cross-section: 18 x 18 mm Hardness range: 65–69 HRC Cobalt content: 10 % Length tolerance: ±2 mm Cross-section tolerance: h13 Special features DIN 4964, Form B: square profile Hardened, tempered and finish‑ground Ends supplied straight and unground High thermal and wear resistance due to HSS‑EW9Co10 Suitable for precision turning and toolmaking applications FAQ What material is the blank made from and why is it suitable for turning? The turning blank is made from HSS‑EW9Co10 (material number 1.3207); the alloy’s 10% cobalt content increases red hardness and wear resistance, making the blank well suited for precision turning and interrupted cuts. What are the exact dimensions and tolerances of the blank? The blank is supplied as a square 18 x 18 mm profile, 200 mm long, with cross‑section tolerance h13 and length tolerance ±2 mm (SKU 4118415185NW). Is the blank ready to machine immediately on delivery? Yes. The Wilke blank is hardened, tempered and finish‑ground, with straight, unground ends, allowing immediate use in production after appropriate fixturing. How does the heat treatment benefit production runs? The 65–69 HRC hardness provides consistent edge support and dimensional stability during machining, which helps reduce rework and prolongs the life of cutting tools when working with this blank. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
200mm Square Turning Bar Form B HSS-EW9Co10 10% Co, Hardened 65-69 HRC, h13 Tolerance +/-2mm - Werner Wilke Zerspanungstechnik GmbH
Benefit from a hardened, cobalt‑enriched turning blank with tight cross‑section tolerance and straight ends for reliable clamping and consistent chip formation; order the part directly via Metav Werkzeuge or ask the consultants for application advice. Werner Wilke turning blank (DIN 4964 Form B) — HSS‑EW9Co10, square 25 x 25 mm, L 200 mm Werner Wilke turning blank for precision turning, manufactured to DIN 4964 Form B for use in toolmaking and workshop turning operations HSS‑EW9Co10 with 10% cobalt for toughness Hardened to 65–69 HRC for long tool life Square 25 x 25 mm cross‑section, tolerance h13 Length 200 mm, straight ends, finish ground Engineered for consistent turning performance The turning blank is manufactured from HSS‑EW9Co10 (material number 1.3207), a high‑speed steel alloy containing 10% cobalt, which raises hot hardness and improves wear resistance during demanding cuts. The heat treatment resulting in 65–69 HRC hardness delivers a robust core suitable for repeated roughing passes, while the body being finish‑ground ensures uniform section geometry for predictable clamping. These characteristics translate into fewer regrinds and reduced set‑up adjustments on lathes and automatic centres. Dimensional certainty that supports fixture and chucking decisions Produced to DIN 4964 in Form B (square), the bar features a 25 x 25 mm cross‑section with a h13 tolerance and a length of 200 mm with a length tolerance of +/- 2 mm. The combination of cross‑section precision and clearly specified length tolerance simplifies jigs, collet and chuck selection and reduces trial fitting. Ends are supplied straight and unground, which is advantageous for controlled facing operations or for custom end‑preparation prior to final mounting. Material, treatment and workshop benefits explained Using HSS‑EW9Co10 provides higher red hardness compared with standard HSS, making the bar suitable where elevated cutting temperatures occur. The material is hardened, tempered and finish‑ground, offering a balance between hardness and toughness: hardness gives cutting edge support; toughness resists chipping under interrupted cuts. For practical workshop planning, these metallurgical properties mean fewer workpiece rejects and improved repeatability when producing turned components from medium‑duty steels and alloyed materials. Suitable applications and handling recommendations This square turning stock is intended for master bars, customised tool bits and small component batches where square cross‑sections speed up milling or slotting operations prior to turning. The finish ground body enables immediate machining with predictable thermal behaviour; however, as the ends are unground, final facing or centring is recommended before precision finishing. The product’s measured tolerances and alloy composition make it an appropriate choice for pro‑tool rooms, small subcontractors and precision workshops seeking consistent blanks for short to medium production runs. Contact Metav Werkzeuge for tailored advice on integrating this Werner Wilke turning blank into production and to confirm availability for immediate supply via Metav Werkzeuge GmbH Technical Data Article number: 4118415255NW Brand: Werner Wilke Zerspanungstechnik GmbH Product type: Turning blank Standard: DIN 4964 Form: B (square) Material: HSS‑EW9Co10 Key figures Cross‑section: 25 x 25 mm Length L: 200 mm Hardness: 65–69 HRC Cross‑section tolerance: h13 Length tolerance: +/- 2 mm Cobalt content: 10 % Special features Werkstoffnummer 1.3207 Hardened, tempered and finish‑ground body Ends straight and unground Packaging unit: 1 FAQ What material is the bar made from and why does it matter? The bar is made from HSS‑EW9Co10 (1.3207); the cobalt content increases hot hardness and wear resistance, which benefits continuous turning and intermittent cuts. Is the cross‑section guaranteed for fixture fitting? Yes, the square cross‑section is specified as 25 x 25 mm with tolerance h13, providing predictable fit for collets and clamps. Can the blank be used immediately in precision turning centres? The body is finish‑ground, so the blank is ready for most machining operations; final end‑facing or centring is recommended because the ends are supplied unground. What does the hardness range mean for tool life? A 65–69 HRC hardness provides durable edge support and wear resistance, which equates to longer service life under typical workshop cutting conditions. Which standard and form apply to this turning stock? Manufactured to DIN 4964, Form B (square), suitable where standardised dimensions and interchangeability are required. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
200mm Square Turning Bar HSS-EW9Co10 10% Co Hardened 65-69 HRC, h13 / +/-2mm - Werner Wilke Zerspanungstechnik GmbH
Take advantage of a high-performance HSS-EW9Co10 composition with 10% cobalt and a hardened finish of 65–69 HRC for durable, wear-resistant turning performance; precise 8 x 8 mm square dimensions and h13 tolerance ensure consistent clamping and reduced setup time. Order directly via Metav Werkzeuge or consult our specialists for application advice. WILKE turning blank DIN 4964 Form B — HSS‑EW9Co10 square 8×8 mm, 200 mm A WILKE turning blank engineered for precision turning and toolroom applications, produced to DIN 4964 Form B for consistent square stock. HSS‑EW9Co10 with 10% cobalt content Hardened to 65–69 HRC for extended life Square 8 x 8 mm cross-section, DIN 4964 Form B Length 200 mm with h13 cross-section tolerance Outstanding material performance for demanding turning tasks The high‑alloy composition of HSS‑EW9Co10 (material number 1.3207) provides enhanced hot hardness and abrasion resistance compared with standard high‑speed steels. With a 10% cobalt content, the steel maintains cutting integrity at elevated temperatures and under intermittent cutting loads, which translates into longer tool life and fewer interruptions in production. The specified hardness of 65–69 HRC indicates a thermally treated and finish‑ground condition that supports repeatable machining results and predictable wear behaviour. Accurate geometry that speeds up setup and improves repeatability Manufactured to DIN 4964 Form B, the square 8 x 8 mm cross‑section is finish‑ground to tight tolerances (h13) and supplied in a nominal 200 mm length. These dimensional controls reduce the need for repeated measurement and fitting at the lathe chuck or collet, therefore lowering setup time and scrap rates. Ends are supplied straight and unground, enabling flexible end preparation on arrival while the finish‑ground body guarantees consistent clamping and aligned rotation during turning operations. Application benefits and practical considerations This square turning stock is suited to precision turning, small‑batch components and toolroom tasks where material stability and wear resistance are essential. The combination of a hardened condition and high‑cobalt content makes the blank especially resilient when producing small parts or finishing operations that generate heat. Because the ends are unground, a quick facing operation will deliver optimal seating; the robust material condition reduces the frequency of replacement and supports predictable process planning. Proven sourcing and quality assurance for the workshop Sourcing via an experienced precision partner delivers added reliability: stock is filtered and distributed from a central European hub that emphasises consistent quality and supply continuity. Metav’s approach to supply chain reliability and product range supports efficient procurement for industry and craft, allowing workshops to consolidate suppliers while retaining access to high‑quality materials. This level of service helps maintain production throughput and a dependable inventory of turning blanks. For tailored technical advice on the WILKE turning blank or to arrange supply directly from Metav Werkzeuge, contact our specialists at info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: 4118415090NW Product type: Turning blank (Drehling) Material: HSS‑EW9Co10 (1.3207) Cross‑section: 8 x 8 mm Length: 200 mm Hardness: 65–69 HRC Cobalt content: 10% Form standard: DIN 4964 Form B Length tolerance: +/- 2 mm Cross‑section tolerance: h13 Facts Hardness value: 65–69 HRC Cobalt proportion: 10% Length: 200 mm Cross‑section: 8 x 8 mm Length tolerance: +/- 2 mm Cross‑section tolerance: h13 Special features Hardened, tempered and finish‑ground Ends straight and unground Square section, DIN 4964 Form B Material number 1.3207 Supplied as single unit (packaging unit 1) FAQ What material is the bar made from and why is it chosen? The turning blank is made from HSS‑EW9Co10 (1.3207); the 10% cobalt content improves hot hardness and wear resistance, which makes the material suitable for demanding turning operations. Which dimensions and tolerances are supplied? The WILKE turning blank is supplied in a 8 x 8 mm square section and 200 mm nominal length, with cross‑section tolerance h13 and a length tolerance of +/- 2 mm. Are the ends prepared for immediate use in the chuck? Ends are delivered straight and unground, while the body is finish‑ground; a facing operation is recommended for optimal seating before chucking. Is the bar coated or treated beyond hardening? No coating is specified; the product is provided hardened, tempered and finish‑ground as indicated in the technical description. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
200mm Square Turning Bar HSS-EW9Co10 10% Coated Hardened 65-69 HRC, h13, +/-2mm - Werner Wilke Zerspanungstechnik GmbH
Take advantage of the high‑hardness HSS composition and the precise h13 cross‑section tolerance to secure consistent, wear‑resistant blanks for serial turning and toolmaking. Order the part directly via Metav Werkzeuge or contact our technical team for specification checks. Turning bar DIN 4964 Form B — 12 x 12 mm HSS‑EW9Co10, 200 mm (WILKE) The turning bar DIN 4964 Form B is a hardened, finish‑ground square stock designed for precision lathe and toolroom applications where dimensional stability and elevated wear resistance are required. HSS‑EW9Co10 high‑speed steel with 10% cobalt Hardened and tempered, 65–69 HRC Square 12 x 12 mm precision ground stock Length 200 mm with ±2 mm length tolerance Consistent hardness for durable turning blanks The combination of HSS‑EW9Co10 and a specified hardness of 65–69 HRC ensures high resistance to abrasion and thermal softening under intermittent cutting loads. For operations that demand prolonged tool life and repeatable results, this hardened and tempered square stock reduces the frequency of rework and replacement. The metallurgical grade 1.3207 describes a robust high‑speed steel alloy with a 10% cobalt share, which improves red hardness and wear behaviour during elevated cutting temperatures. Precision dimensions that support accurate part production With a 12 x 12 mm cross‑section produced to h13 tolerance and a nominal length of 200 mm, the blank provides clear dimensional reference for chucking and clamping. The declared length tolerance ±2 mm minimises setup variation for short‑run turning and toolmaking tasks. The DIN 4964 Form B specification and finish‑ground body allow straightforward integration into jigs and fixtures, while the square geometry simplifies centring and ensures a repeatable datum for downstream machining. Practical machining and finishing advantages The stock is supplied finish‑ground, with ends that are straight but unground, allowing users to establish custom datum faces or to perform final face machining as required. The hardened condition is suited to applications where blanks are reshaped, ground or partially turned to create precision components. Because of the alloy composition and heat treatment, the material maintains cutting performance under higher thermal loads; this is particularly beneficial when producing small, high‑precision parts that require tight surface quality and consistent mechanical properties. Quality assurance and workshop reliability Manufactured to DIN 4964 and checked for cross‑section tolerance, the blank offers a verifiable basis for procurement decisions in workshops and small production environments. The square turning stock reduces the need for additional clamping accessories in many fixtures and contributes to a predictable production flow. Paired with Metav’s distribution and product range, the item supports a streamlined supply process for precision engineering tasks without compromising on material integrity or traceability. For precision applications requiring hardened, cobalt‑alloy turning blanks, consider the WILKE turning bar supplied via Metav Werkzeuge — technical enquiries and order coordination are available through Metav Werkzeuge (info@metav-werkzeuge.com, +49 2822 7131930) Technical data Article number: 4118415130NW Material: HSS‑EW9Co10 Material number: 1.3207 Product type: Turning bar (Drehling) Standard: DIN 4964 Form: B (square) Facts Length: 200 mm Cross‑section: 12 x 12 mm Hardness: 65–69 HRC Cobalt content: 10% Length tolerance: ±2 mm Cross‑section tolerance: h13 Special features Form B: square section Hardened, tempered and finish‑ground Ends supplied straight and unground Suitable for precision turning and toolroom use Packing unit: 1 FAQ What material is the blank made from and what are its key properties? The turning bar is produced from HSS‑EW9Co10 (material number 1.3207), an alloyed high‑speed steel with 10% cobalt; this composition provides improved red hardness and wear resistance for the hardened condition. What does the stated hardness of 65–69 HRC mean for machining? A hardness of 65–69 HRC indicates a high wear‑resistant condition; the turning bar DIN 4964 Form B should be used where durability is required and where final machining or grinding is planned, rather than extensive rough cutting. How precise are the dimensions and what tolerances apply? The square stock is 12 x 12 mm to h13 cross‑section tolerance, with a nominal length of 200 mm and a length tolerance of ±2 mm, providing consistent sizing for fixture and chuck setups. Why are the ends supplied straight but unground? Ends are supplied unground to allow users to establish their own datum faces or to perform final facing operations; the body is finish‑ground to ensure accurate cross‑section and surface condition for clamping and indexing. Is this product suitable for toolroom and small production runs? Yes; the hardened, finish‑ground turning bar is intended for precision turning and toolmaking tasks where repeatability and wear resistance support short to medium production sequences. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
200mm Square Turning Bar HSS-EW9Co10 10% Cobalt 65-69 HRC h13 Tolerance +/-2mm DIN 4964 Form B - Werner Wilke Zerspanungstechnik GmbH
Robust high‑speed steel and precision tolerances combine to deliver a reliable turning blank for demanding production environments; its HSS‑EW9Co10 composition with 10% cobalt and a hardness of 65–69 HRC ensures extended tool life and stable performance. Order the turning blank directly via Metav Werkzeuge or contact the consultants for application advice. WILKE turning blank DIN 4964, Form B — 20 x 20 mm, HSS‑EW9Co10, L 200 mm WILKE turning blank DIN 4964 Form B is a square, hardened and finish‑ground high‑speed steel bar intended for precision turning and small‑batch production. Hardened to 65–69 HRC for long tool life Square cross‑section 20 x 20 mm, tolerance h13 High‑speed steel HSS‑EW9Co10 with 10% cobalt Finished ground length 200 mm, tolerance ±2 mm Longer service life through heat treatment and alloying The HSS‑EW9Co10 alloy, with a 10% cobalt content, increases red hardness and wear resistance compared with conventional high‑speed steels. Combined with a 65–69 HRC hardness after hardening and tempering, this material choice reduces flank wear under elevated cutting temperatures and extends in‑service life. For production planners, this equates to fewer tool changes and improved process stability during prolonged machining cycles. Predictable dimensions that speed up setup A 20 x 20 mm square cross‑section with h13 tolerance and a length of 200 mm (length tolerance ±2 mm) provides consistent reference surfaces for chucking and clamping. The finish‑ground condition ensures straight, machinable faces, lowering set‑up times and minimising adjustment during first‑piece runs. Reliable dimensional control supports reproducible part quality in serial turning and reduces scrap rates. Material designation and standards for correct specification Provided in accordance with DIN 4964, material number 1.3207 indicates a recognised high‑speed steel grade suitable for a wide range of turning tasks. The specification clarifies metallurgical properties to purchasing and quality departments, enabling straightforward material comparisons and compliance checks. The hardened and finish‑ground delivery state simplifies integration into existing machining workflows without additional heat treatment. Practical advantages on the shop floor Delivered as a square turning blank with straight, unground ends, this bar is ready for facing, centre drilling and clamping. The combination of finish grinding and a robust cobalt‑enriched matrix supports stable cutting conditions when machining alloyed steels and other demanding materials. Reduced tool wear and steady cutting forces translate into predictable cycle times and a more efficient production rhythm. For precision turning tasks, request technical advice from Metav Werkzeuge—reach the Emmerich team at info@metav-werkzeuge.com or +49 2822 7131930 to confirm suitability and lead times for this WILKE turning blank (SKU 4118415220NW). Technical data Article number: 4118415220NW Product type: Turning blank Material: HSS‑EW9Co10 Standard: DIN 4964 Core technical data Length: 200 mm Cross‑section: 20 x 20 mm Length tolerance: ±2 mm Cross‑section tolerance: h13 Hardness: 65–69 HRC Cobalt content: 10% Material number: 1.3207 Special features Form B: square Hardened, tempered and finish‑ground Ends straight and unground Packaging unit: 1 FAQ What applications is this turning blank suitable for? The WILKE turning blank (DIN 4964, Form B) is suitable for precision turning and small‑batch production where high wear resistance and dimensional stability are required. Can the HSS‑EW9Co10 material handle elevated cutting temperatures? Yes, the HSS‑EW9Co10 composition with 10% cobalt provides enhanced red hardness, making the material resilient under higher cutting temperatures compared with standard high‑speed steels. How precise is the cross‑section of the bar? The square cross‑section is 20 x 20 mm with tolerance h13, offering consistent dimensions for reliable clamping and machining setups. Is the bar delivered ready for machining? The bar is hardened, tempered and finish‑ground with straight, unground ends, so it is ready for facing and clamping before turning operations. Which standard and material number are referenced for specification? The product conforms to DIN 4964 and is listed under material number 1.3207, simplifying specification and procurement checks. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
200mm Square Turning Bar HSS-EW9Co10 10% Cobalt Hardened 65-69 HRC h13 Tolerance, DIN 4964 Form B - Werner Wilke Zerspanungstechnik GmbH
Take advantage of a combination of high-alloy HSS material, precise hardened finish and defined dimensional tolerances for dependable tool blanks in production. Secure consistent machining results and reduced rework by choosing this robust turning blank — order the item directly via Metav Werkzeuge or consult the team for technical advice. Turning blank DIN 4964 Form B — square 16 x 16 mm, HSS‑EW9Co10 (10% Co) Turning blank DIN 4964 Form B in HSS‑EW9Co10, ideal for production of small tools and precision components where high wear resistance is required. HSS with 10% cobalt for hot hardness Hardened and ground to 65–69 HRC Square cross-section 16 x 16 mm, Form B Length 200 mm with +/- 2 mm tolerance High‑alloy steel for longer tool life The turning blank is manufactured from HSS‑EW9Co10 (material number 1.3207), a high‑speed steel alloy with 10% cobalt that raises hot hardness and wear resistance. This metallurgical composition provides a measurable advantage during manufacturing: less frequent regrinding and longer intervals between replacements. The hardened condition (65–69 HRC) combined with a final ground finish ensures a consistent surface state that helps to reduce micro‑fracture initiation and improves performance under intermittent cutting loads. Consistent dimensions for reliable set‑up Delivered as a square 16 x 16 mm bar in DIN 4964 Form B, the blank features a cross‑section tolerance h13 and a length tolerance of +/- 2 mm. These specifications support repeatable clamping and fixturing in toolmaking and small‑batch production. The straight, unground ends allow flexible holding options, while the defined tolerances cut down setup time and minimise the need for individual trimming before final machining, resulting in smoother production flows. Standard conformity and what it means in practice Compliance with DIN 4964 signals that the component is manufactured to a recognised German industry standard for turning blanks, simplifying part selection and storage. The material designation and Werkstoffnummer 1.3207 permit direct cross‑referencing in procurement systems and material declarations. The combination of standardised form, heat treatment and finish means predictable mechanical behaviour during turning, slotting or further tool fabrication processes. Practical benefits for workshop use Because the blank is hardened, tempered and finished by grinding, it can be used as a near‑ready starting material for small tooling, gauges or specialised fixtures. The inherent wear resistance reduces downstream finishing operations and supports automated workflows where consistent billet geometry is essential. For toolmakers working to short lead times, the ready‑to‑process condition delivers a clear time saving and reduces the risk of scrap. Supply reliability and trusted sourcing Choosing industrial stock from a reliable partner reduces procurement headaches. Metav’s model of centralised quality control and supply from Emmerich acts as a “quality filter” for the European market, supporting continuity in the shop floor supply chain. The robust material properties and documented tolerances of this turning blank align with the needs of precision workshops and small manufacturers seeking dependable raw components. For technical clarification or to confirm suitability for a specific application, contact Metav Werkzeuge GmbH in Emmerich: info@metav-werkzeuge.com | +49 2822 7131930 — consultants are available to advise on specifications and ordering. Technical data Article number: 4118415166NW Product type: Turning blank (Drehling) Manufacturer: Werner Wilke Zerspanungstechnik GmbH Facts Cross-section: 16 x 16 mm Length: 200 mm Hardness: 65–69 HRC Length tolerance: +/- 2 mm Cross-section tolerance: h13 Cobalt content: 10% Material number: 1.3207 Special features Standard: DIN 4964, Form B (square) Material: HSS‑EW9Co10 Condition: hardened, tempered and finish‑ground Ends: straight and unground Packaging unit: 1 FAQ What is the hardness of this turning blank? The turning blank is delivered in a hardened condition with a hardness of 65–69 HRC, offering high wear resistance for toolmaking and small component fabrication. Which material is used and what does the designation mean? The billet is made of HSS‑EW9Co10 (Werkstoffnummer 1.3207) — a high‑speed steel alloy containing 10% cobalt to improve hot hardness and cutting durability. What are the exact dimensions and tolerances? The square cross‑section is 16 x 16 mm (Form B), length 200 mm, cross‑section tolerance h13 and length tolerance +/- 2 mm, ensuring repeatable clamping and fit. Is the blank ready for machining or does it require further preparation? The material is hardened, tempered and finish‑ground, which reduces preparatory grinding; ends are straight and unground to allow flexible holding and final finishing as required. Which standard does the product comply with? Manufactured to DIN 4964 (Form B), facilitating straightforward specification and interchangeability within standard tooling processes. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
200mm Square Turning Bar HSS-EW9Co10 10% Cobalt Hardened 65-69 HRC, h13 Tolerance +/-2mm - Werner Wilke Zerspanungstechnik GmbH
Take advantage of a high‑alloy HSS composition (10% cobalt) and 65–69 HRC hardness to extend machining life and maintain dimensional stability; the square 10 x 10 mm cross section with h13 tolerance and a length of 200 mm ensures consistent set‑up and repeatability on machines. Order the turning blank directly via Metav Werkzeuge or consult our specialists for application advice. Turning blank DIN 4964 Form B — 10 x 10 mm HSS‑EW9Co10, 200 mm — Wilke A turning blank DIN 4964 Form B designed for precision turning and toolmaking applications, providing a hardened and ground square bar for reliable clamping and machining. Hardened to 65–69 HRC for extended life HSS with 10% cobalt for high heat resistance Precise 10 x 10 mm square cross section h13 Length 200 mm; straight ends, ground finish Consistent performance through material choice and hardness The bar stock is manufactured from HSS‑EW9Co10 (material 1.3207), a high‑speed steel alloy with 10% cobalt that improves red‑hardness and wear resistance under elevated cutting temperatures. Combined with a 65–69 HRC hardness rating, this composition reduces flank wear and prolongs service intervals, which is particularly beneficial for serial turning operations where tool life and reproducible results are essential. The choice of material and heat treatment therefore supports cost‑effective production by reducing downtime and tool changes. Precision dimensions and tolerances for reliable set‑up With a 10 x 10 mm square cross section produced to h13 tolerance and a nominal length of 200 mm, the item provides a reproducible datum for chucks and collets. The length tolerance of +/- 2 mm and straight, ground ends simplify fixturing and ensure accurate axial positioning without the need for additional machining. These dimensional assurances translate into shorter set‑up times and fewer rejects when integrating the blank into existing workflows or bespoke fixtures. Machining suitability and practical benefits The combination of high‑alloy HSS and elevated hardness makes the component suitable for turning a range of steels and alloyed materials where heat generation is a limiting factor. The material’s characteristics enable secure roughing and finishing passes without premature softening. As a precut, ground square bar, it eliminates the initial material‑preparation step for many shop processes, delivering a ready‑to‑mount solution that supports both small‑batch and larger production runs. Quality assurance and operational integration Supplied to DIN 4964 Form B, the blank is hardened, tempered and finish ground, with ends left straight and unground to allow custom end machining if required. The controlled manufacturing process and traceable material designation (1.3207) provide confidence in repeat orders and component interchangeability. For procurement and inventory planning, the unit comes packaged as a single piece per pack, facilitating straightforward stock management and predictable consumption. For demanding turning tasks, specify the Wilke turning blank when ordering from Metav Werkzeuge — Metav’s consultants are available for technical matching and application recommendations via info@metav-werkzeuge.com or by telephone on +49 2822 7131930. Technical data SKU: 4118415115NW Product type: Turning blank (Drehling) Manufacturer: Werner Wilke Zerspanungstechnik GmbH Facts Length: 200 mm Cross section: 10 x 10 mm Hardness: 65–69 HRC Cobalt content: 10% Length tolerance: +/- 2 mm Cross‑section tolerance: h13 Special features Material: HSS‑EW9Co10 (1.3207) Standard: DIN 4964 Form B Square, hardened, tempered and finish ground Ends straight and unground Pack unit: 1 FAQ What materials is this turning blank suitable for? The turning blank from Werner Wilke, made of HSS‑EW9Co10, is suitable for machining a variety of steels and alloyed materials where high cutting temperatures may occur. How does the 10% cobalt content affect performance? The 10% cobalt alloy increases red‑hardness and wear resistance, so the Wilke blank maintains cutting performance under thermal load better than standard HSS. What dimensional tolerances can be expected? The square cross section is supplied to h13 tolerance and the length is specified as 200 mm with a ±2 mm length tolerance, ensuring reliable clamping and repeatability. Are the ends ready for immediate clamping in collets or chucks? The piece is delivered with straight, finish‑ground ends; the ends are unground where specified, allowing secure clamping and optional final machining if required. Is material traceability available for repeat orders? Yes, the material designation 1.3207 and the DIN 4964 Form B specification support consistent quality and traceability for ongoing procurement. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
200mm Square Turning Bar HSS-EW9Co10 14x14mm Hardened 65-69 HRC, h13 Tolerance +/-2mm - Werner Wilke Zerspanungstechnik GmbH
Take advantage of a hardened, finish‑ground square turning blank in HSS‑E with 10% cobalt and conformity to DIN 4964 for reliable, repeatable turning operations; combine high wear resistance and tight dimensional control for uninterrupted production. Order the turning blank directly via Metav Werkzeuge or ask our consultants for application advice. Turning blank DIN 4964, Form B — 14 x 14 mm HSS‑E (10% Co) by Werner Wilke The turning blank supplies hardened, finish‑ground square stock for precision turning and workshop fabrication, compliant with DIN 4964 and suited to demanding toolroom work HSS‑E with 10% cobalt for wear resistance Hardened 65–69 HRC for stable machining Square 14 x 14 mm cross-section, finish-ground Length 200 mm with ±2 mm dimensional tolerance Longer tool life through robust material choice The use of HSS‑E (high‑speed steel) with 10% cobalt gives a clear technical advantage: higher red‑hardness and improved wear resistance compared with conventional HSS, which extends service intervals and reduces downtime. Conformity to DIN 4964 and the specified material number 1.3207 ensure traceable metallurgy and consistent microstructure. For machine shops aiming for predictable tool performance, this solid steel stock provides a durable base material for precision turning and small‑batch production, lowering the frequency of stock replacement and stabilising process costs. Reliable dimensional control and machining stability A square 14 x 14 mm section, finish‑ground and produced to h13 cross‑section tolerance with a length tolerance of ±2 mm, simplifies clamping and repeat setups in collets or vices. The 65–69 HRC hardness rating means the bar resists edge chipping during roughing and maintains form during facing and profiling operations, so fewer corrections are required after machining. Where concentricity and predictable chip formation matter, the combination of finish grinding and standardised dimensions supports quicker set‑up and consistent component quality in everyday workshop use. Process readiness and quality assurance for the workshop Supplied with straight, unground ends and a 200 mm nominal length, this turning blank arrives ready for chucking, shortening or straight turning without further heat treatment. The square form B geometry is especially useful for parts that require fixed orientation or for producing flats and profiles directly from the blank. Backed by documented standards and the material designation 1.3207, the component supports quality control procedures and simplifies material declarations for assemblies. For precision‑focused operations, the blank reduces variation between batches and contributes to a repeatable manufacturing chain. Contact Metav Werkzeuge for technical guidance and secure supply of HSS‑E turning blanks – available from the Emmerich warehouse and packed for immediate use, call +49 2822 7131930 or email info@metav-werkzeuge.com Technical data SKU: 4118415144NW Item: Turning blank (turning stock) Brand: Werner Wilke Zerspanungstechnik GmbH Standard: DIN 4964 Material number: 1.3207 Facts Cross-section: 14 x 14 mm Length: 200 mm Hardness: 65–69 HRC Cross-section tolerance: h13 Length tolerance: ±2 mm Cobalt content: 10% Special features Material: HSS‑EW9Co10 (high‑speed steel with cobalt) Form: B, square, finish‑ground Ends: straight and unground Pack size: 1 FAQ What material is the turning blank made from? The turning blank is manufactured from HSS‑EW9Co10 (material 1.3207), a high‑speed steel with 10% cobalt for increased wear resistance. Which DIN standard does the product follow? Production and dimensions conform to DIN 4964, Form B, ensuring standardised square stock for workshop use. Is the cross‑section precision suitable for collet clamping? Yes, the 14 x 14 mm cross‑section is finish‑ground and specified to h13 tolerance, which supports secure clamping and consistent set‑ups. How hard is the blank and what does that mean for machining? With a hardness of 65–69 HRC, the blank offers good wear resistance; machining parameters should be adjusted for high‑hardness HSS stock to optimise tool life and surface finish. What is the delivered length tolerance? The nominal length is 200 mm with a dimensional tolerance of ±2 mm, suitable for standard workshop preparations. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
80mm 5mm Solid Carbide Round Bar HSS-EW9Co10, Hardened 65-69 HRC, Diameter h8, Length Tolerance +/- 2 mm - Werner Wilke Zerspanungstechnik GmbH
Take advantage of a hardened, finish-ground HSS-EW9Co10 blank with 65–69 HRC for consistent cutting performance and tight dimensional control; order directly via Metav Werkzeuge or consult our technical team for application advice. WILKE turning blank DIN 4964 Form A – Ø 5 mm, HSS-EW9Co10 WILKE turning blank DIN 4964 Form A – Ø 5 mm, HSS-EW9Co10 is a hardened, finish-ground round bar designed as a precision blank for turning and small-part production, compliant with DIN 4964 Form A for consistent geometry and machinability. Hardened and finish-ground, 65–69 HRC Solid HSS-EW9Co10 with 10% cobalt Ø 5 mm, tolerance h8 Length 80 mm, length tolerance ±2 mm Precision material for reliable tool life and repeatable results The HSS-EW9Co10 composition with 10% cobalt delivers elevated hot hardness and wear resistance compared with standard high-speed steels, making it suitable where toughness and abrasion resistance are required. The blank is hardened, tempered and finish-ground, resulting in a uniform microstructure and surface that reduces variation between batches. For production environments this translates into fewer tool changes, predictable tool life and improved process stability when fabricating turned components from a range of commonly used metals. Dimensional accuracy that simplifies set-up and inspection Produced to DIN 4964 Form A, the round bar is supplied with Ø 5 mm diameter and a tolerance of h8, plus a length of 80 mm with a ±2 mm length tolerance. The combination of diameter tolerance h8 and finish grinding ensures good concentricity and consistent clamping behaviour in chucks and collets, which supports higher first-pass yields. The ends are supplied straight and unground, allowing final facing or custom end preparation to match specific mounting or assembly needs while keeping the core geometry stable. Workshop efficiency and compatibility with precision turning operations Delivered as a ready, finish-ground blank, the component minimises preparatory processing for small-batch work and prototype runs. The high hardness range (65–69 HRC) reduces the tendency for plastic deformation during clamping and offers a stable base for downstream grinding or turning operations. Specified as material number 1.3207, this round bar is a compact option for toolmakers, model engineers and precision workshops that demand reproducible starting stock for tight-tolerance parts. Clear material and hardness specifications aid in selecting appropriate cutting data and coolant strategies to achieve the desired surface finish. Contact Metav Werkzeuge for availability and compatibility guidance on the WILKE turning blank; our consultants can advise on suitability for specific applications and recommend cutting parameters — eMail: info@metav-werkzeuge.com | Tel: +49 2822 7131930 Technical data Article number: 4118401040NW Brand: WILKE Product type: Turning blank (Drehling) Standard: DIN 4964 Form A Facts Diameter: 5 mm (Ø 5 mm) Length: 80 mm Hardness: 65–69 HRC Diameter tolerance: h8 Length tolerance: ±2 mm Material number: 1.3207 Cobalt content: 10% Special features Material: HSS-EW9Co10 Hardened, tempered and finish-ground Ends straight and unground Compliant with DIN 4964 Form A FAQ What is the material composition and why does it matter? The WILKE turning blank is made from HSS-EW9Co10 (material no. 1.3207) and contains 10% cobalt, which increases red hardness and wear resistance; this helps maintain cutting edge and dimensional stability under elevated cutting temperatures. Which tolerances and dimensions are specified for the blank? The blank (SKU 4118401040NW) is supplied as Ø 5 mm with tolerance h8 and a length of 80 mm with a ±2 mm tolerance; hardness is specified at 65–69 HRC. Are the ends ready for immediate clamping or is additional preparation required? Ends are delivered straight and unground, so final facing or end preparation is typical to achieve specific concentricity or clamping requirements before precision finishing operations. Which standard does this blank conform to and how does that help in production? The round bar conforms to DIN 4964 Form A, which ensures consistent geometry and interchangeability when used as a starting blank for turning and precision machining. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
80mm Round Centre Shaft HSS-EW9Co10 10% Co 65-69 HRC, h8 Tolerance +/-2mm - Werner Wilke Zerspanungstechnik GmbH
Take advantage of a hardened, ground round blank with a high-cobalt HSS composition for consistent tool performance and long life; the combination of 65–69 HRC hardness and h8 diameter tolerance ensures repeatable results in precision turning. Order the item via Metav Werkzeuge or request advice from our consultants for batch supply and delivery. WILKE turning blank DIN 4964 Form A — 4 mm, HSS‑EW9Co10 The WILKE turning blank DIN 4964 Form A is a round, hardened and ground bar designed for precision turning applications in toolmaking and small-series production. HSS‑EW9Co10 with 10% cobalt Hardness 65–69 HRC Diameter tolerance h8 Ground finish and straight ends Consistent cutting behaviour through high‑performance material The use of HSS‑EW9Co10 (Werkstoff 1.3207) delivers improved red hardness and wear resistance compared with conventional high‑speed steels, which translates into more consistent cutting behaviour under thermal load. With a cobalt content of 10%, the material maintains hardness at elevated temperatures, reducing flank wear and extending blank life. This translates into fewer re‑grinds and steadier machine cycles for precision turning operations. Predictable dimensional accuracy for repeatable parts Manufactured to DIN 4964 Form A, the round blanks are ground and supplied with straight, unground ends to simplify clamping and preparation. The diameter 4 mm with h8 tolerance and length 80 mm supports tight concentricity and repeatable set‑ups on lathes and CNC turning centres. The 65–69 HRC heat treatment ensures dimensional stability in short runs and helps maintain concentricity during machining, reducing scrap and increasing first‑pass yields. Practical benefits for workshop efficiency Using a pre‑finished turning blank minimises preparation time: the ground surface reduces balancing and centring effort, while uniform hardness offers consistent tool life across batches. For small workshops and specialist toolrooms, the blanks provide a reliable starting point for prototyping, small batch production or specialised tooling components. Combined with Metav’s supply chain and quality filtering from Emmerich, this provides a pragmatic route to integrating precision blanks into existing processes with minimal disruption. Contact Metav Werkzeuge for tailored advice on batch quantities, lead times and delivery from Emmerich — email info@metav-werkzeuge.com or call +49 2822 7131930 Technical Data Article number: 4118401028NW Item: Turning blank Material: HSS‑EW9Co10 Material number: 1.3207 Standard: DIN 4964 Facts Diameter: 4 mm Length: 80 mm Hardness: 65–69 HRC Diameter tolerance: h8 Length tolerance: ±2 mm Cobalt content: 10% Special features DIN 4964 Form A: round Hardened, tempered and ground Ends straight and unground Supplied finished for precision turning FAQ What material is the blank made from and what are the benefits of it? The blank is manufactured from HSS‑EW9Co10 (Werkstoff 1.3207); the 10% cobalt content improves hot hardness and wear resistance, delivering stable cutting performance for turning operations. What tolerances and dimensions can be expected from the blank? The round blank is supplied with a 4 mm diameter to h8 tolerance and a length of 80 mm with a length tolerance of ±2 mm, suitable for precision turning set‑ups. Is the blank heat treated or ground before delivery? Yes, the blank is hardened, tempered and finished by grinding, leaving straight, unground ends to simplify clamping and subsequent machining. Which standard does the blank conform to? The product conforms to DIN 4964 Form A, specifying a round turning blank finished for precision use. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
80mm Square Turning Bar 5x5mm HSS-EW9Co10 10% Co Hardened 65-69 HRC h13 +/-2mm, DIN 4964 Form B - Werner Wilke Zerspanungstechnik GmbH
Take advantage of a hardened, finish-ground square turning blank that combines high wear resistance and tight dimensional control for reliable batch production; order directly via Metav Werkzeuge or contact the consultants for application advice. Wilke turning blank DIN 4964 Form B — HSS-EW9Co10, 5 x 5 mm, 80 mm The Wilke turning blank is a square, pre-hardened bar stock for precision machining, suitable for small turning operations and finishing pulses. HSS-EW9Co10 with 10% cobalt for high hardness Hardened and finish-ground for consistent concentricity Square form B (5 x 5 mm) with h13 cross-section tolerance Length 80 mm with ±2 mm length tolerance Faster setup and consistent machining results The combination of finish-ground surfaces and a hardened core delivers repeatable seating and concentric running in chucks and fixtures, reducing setup time and scrap rates. The HSS-EW9Co10 alloy, containing 10% cobalt, ensures elevated red hardness and wear resistance compared with standard high-speed steels, which helps maintain cutting geometry during longer runs. With the 5 x 5 mm square cross section meeting h13 tolerance, the blank fits standard square collets and micro-fixtures without rework, supporting efficient, predictable production cycles. Material engineering that extends tool life and stability Supplied in 1.3207 grade and hardened to 65–69 HRC, the bar stock offers a stable substrate for fine turning, internal tooling and precision features where dimensional integrity matters. The high hardness reduces the frequency of regrinding or repositioning and makes the stock particularly suitable for applications that demand excellent edge retention and resistance to plastic deformation. Because the ends are straight but unground, the component allows secure clamping while preserving the ground length for critical machining, thereby balancing handling convenience with functional precision. Clear specification for process planning and quality control Conforming to DIN 4964, Form B, the component simplifies procurement and inspection: documented tolerances of ±2 mm length and h13 cross-section provide a verifiable basis for incoming inspection and automatic sorting. The square form reduces rotation risk in small chucks and supports consistent tool engagement, which is especially valuable in serial small-part manufacture. Where process engineers require traceability, the material designation and DIN reference allow direct comparison with supplier certifications and internal quality plans, aiding long-term cost-efficiency through fewer rejects and predictable tool cycles. For tailored supply quantities, compatibility checks or application recommendations contact Metav Werkzeuge — our consultants supply technical guidance and logistical support from Emmerich to keep production moving. Technical data SKU: 4118415040NW Product type: Turning blank Material: HSS-EW9Co10 Material number: 1.3207 Standard: DIN 4964 Form: B (square) Facts Cross-section: 5 x 5 mm Length: 80 mm Hardness: 65–69 HRC Cobalt content: 10% Cross-section tolerance: h13 Length tolerance: ±2 mm Special features Hardened, tempered and finish-ground Ends straight and unground Square profile for stable clamping Suitable for precision small-part turning FAQ What material is used for this turning blank and what are its benefits? The turning blank is made from HSS-EW9Co10 (material 1.3207); the 10% cobalt content and hardened condition improve red hardness and wear resistance, extending service life in demanding turning operations. Is the dimension tolerance suitable for collet chucking and micro-fixtures? Yes. The 5 x 5 mm cross section is manufactured to h13 tolerance and the length is supplied as 80 mm with a ±2 mm tolerance, which supports reliable seating in square collets and miniature fixtures. How does the finish-ground condition affect machining outcomes? The finish-ground area enhances concentricity and predictable runout, reducing setup adjustments and improving repeatability across batches when using the Wilke turning blank. Are the ends ready for immediate machining? The ends are supplied straight but unground, permitting secure clamping while preserving the finish-ground length for critical machining operations. Which standard and form identify this stock for procurement and inspection? The stock conforms to DIN 4964, Form B (square), enabling clear specification in procurement orders and compatibility with documented inspection criteria (SKU 4118415040NW). Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
80mm Square Turning Bar Form B 4x4mm HSS-EW9Co10 65-69 HRC h13, +/-2mm Tolerance - Werner Wilke Zerspanungstechnik GmbH
Take advantage of a hardened HSS-EW9Co10 square bar with 10% cobalt and 65–69 HRC hardness for reliable turning operations; the consistent 4 × 4 mm cross-section and 80 mm length with defined tolerances support predictable set-up and throughput. Order the component directly via Metav Werkzeuge or request specialist advice from the consultants. WILKE turning blank DIN 4964, HSS‑EW9Co10, 4×4 mm, 80 mm The WILKE turning blank is a hardened, finish‑ground square bar (Form B) made from high‑speed steel with 10% cobalt, intended for precision turning and small-series toolmaking Hardened and ground, 65–69 HRC for stable turning Square cross‑section 4 × 4 mm, tolerance h13 Length 80 mm with ±2 mm length tolerance Material HSS‑EW9Co10 (Werkstoff 1.3207), 10% cobalt Reliable material choice for demanding cutting tasks The combination of HSS‑EW9Co10 and 10% cobalt delivers increased hot hardness and wear resistance compared with standard high‑speed steels, which helps to maintain edge integrity under elevated temperatures. With a specified hardness of 65–69 HRC, the bar provides a hard, wear‑resistant body that supports repeatable machining results. The material designation Werkstoff 1.3207 and the DIN reference underline a standardised composition, offering confidence for engineering and toolmaking environments where material consistency is essential. Predictable geometry for fast set‑up and consistent parts A square bar (Form B) with a 4 × 4 mm cross‑section and tolerance class h13 simplifies clamping and alignment in turning fixtures and toolholders. The 80 mm overall length and the specified ±2 mm length tolerance allow planners to account for stock removal and chucking clearance without guesswork. The body is finish ground, while the ends are straight and left unground; this configuration delivers a precise working surface along the length while allowing straightforward clamping at the ends. Practical benefits in production and tooling applications Conforming to DIN 4964, the bar is suitable as a solid blank for small turning operations, prototypes and precision tool components where material hardness and dimensional stability are required. The high cobalt content helps to extend tool life in intermittent cuts and under thermal load, reducing downtime for insert changes or regrinds. Specified tolerances and the standardised form support predictable machining cycles, helping to maintain process efficiency and reduce scrap rates in repeat production. For technical advice or to secure delivery from Emmerich, contact Metav Werkzeuge for a tailored consultation by e‑mail at info@metav-werkzeuge.com or by phone on +49 2822 7131930 — assistance and supply direct from the warehouse are available. Technical data Article number: 4118415028NW Label: Drehling DIN 4964 Form B quad.B.4x4mm HSS‑EW9Co10 1.3207 L.80mm WILKE Manufacturer: Werner Wilke Zerspanungstechnik GmbH Product type: Turning blank Standard: DIN 4964 Material: HSS‑EW9Co10 Werkstoff number: 1.3207 Form: B Core technical data Length L: 80 mm Cross‑section: 4 × 4 mm Hardness: 65–69 HRC Cobalt content: 10% Cross‑section tolerance: h13 Length tolerance: ±2 mm Special features Form B: square Hardened, tempered and finish ground Ends straight and unground Querschnitt B: 4 × 4 mm FAQ What material is the turning blank made from? The turning blank is manufactured from HSS‑EW9Co10 (Werkstoff 1.3207), a high‑speed steel alloy containing 10% cobalt for improved hot hardness. What dimensions and tolerances apply to the bar? The component has a 4 × 4 mm cross‑section (tolerance h13) and an overall length of 80 mm with a length tolerance of ±2 mm. How hard is the material and why does that matter? The specified hardness is 65–69 HRC; this level of hardness increases wear resistance and helps to keep cutting edges stable under thermal stress, benefiting tool life and process reliability. Is the bar finish ground along its length? Yes, the bar body is finish ground for dimensional stability, while the ends are straight and left unground. Which standard does this turning blank follow and why is that useful? Compliance with DIN 4964 and the designation Form B ensures standardised geometry for compatibility with fixtures and established tooling procedures. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
Fragen zu diesen Produkten??
Mit mehr als 30 Jahren Erfahrung beraten wir Sie gerne persönlich.
Tel.: +49 2822 7131930
Mail: info@metav-werkzeuge.com