Precision gauge blocks and plug gauges for reliable dimensional control
Mechanical gauge blocks and plug gauges are essential for tactile verification of threads, bores and gap dimensions, providing fast, unambiguous go/no-go results that enhance process reliability and reduce scrap. Designed for industrial metalworking and toolmaking, these precision tools support incoming inspection and final quality checks by delivering traceable measurements in applications such as thread inspection, bore diameter testing and spacing checks. Manufactured from specially hardened, low-distortion alloys and fine-lapped for minimal measurement uncertainty, the range includes thread plug gauges, precision plug gauges and calibration gauge blocks to ensure long-term repeatability and wear resistance.
M46×1.5 Thread Limit Go Gauge For Metric ISO Fine Thread Right-Hand, Hardened Gauge Steel, DIN 13 6H - Metav IndustryLine
Take advantage of a robust combination of dimensional stability, DIN‑conform inspection and straightforward go/no‑go assessment to keep production tolerances tight and rework rates low. Order the gauge via Metav Werkzeuge or consult the sales team for compatibility details and rapid delivery. Limit thread plug gauge M46 x 1.5 mm — right‑hand, DIN 13 (Metav IndustryLine) The limit thread plug gauge M46 x 1.5 mm is a hardened go/no‑go gauge for checking metric ISO fine internal threads in machining and inspection environments Limit thread plug gauge M46 x 1.5 mm Hardened gauge steel for dimensional stability Manufactured to DIN 13, tolerance 6H Right‑hand thread checking, workshop use Faster compliance checks that reduce rework A dedicated limit thread plug gauge provides immediate pass/fail feedback for internal threads, cutting inspection time compared with full dimensional measurement. The M46 x 1.5 mm size matches common fine‑thread applications in assemblies where correct fit is critical; compliance with DIN 13 and tolerance class 6H ensures that a single, simple check corresponds to established thread standards. The result is fewer downstream adjustments, lower scrap rates and a more predictable production flow. Built for repeatability and long service life Constructed from hardened gauge steel, the plug gauge resists wear and maintains its profile across repeated use, supporting consistent go/no‑go decisions over many cycles. The robust construction and compact mass (approximately 0.8 kg) make the gauge easy to handle while delivering the stiffness needed for repeatable results. The right‑hand orientation corresponds to standard manufacturing practice for metric threads, so the gauge integrates naturally into shop routines without special fixturing. Practical integration into workshop inspection regimes This limit gauge is intended for the workshop and quality station where rapid verification is required rather than full measurement reporting. Use the plug gauge for routine checks on production runs, incoming part inspection or first‑article verification to flag non‑conforming threads before assembly. The simple go/no‑go principle reduces operator training needs while the DIN‑based specification allows immediate comparability across suppliers and inspection records. The compact design supports safe storage and fast retrieval on the inspection bench. Discuss technical compatibility or request supply from Metav Werkzeuge for delivery and further product information directly from the Emmerich facility Technical Data Article number: M315.046.6 GTIN: 4054469123387 Facts Thread size: M46 x 1.5 mm Weight: 0.8 kg Tariff number: 90173000 Special features Material: Hardened gauge steel Standard: DIN 13, tolerance class 6H Right‑hand thread Category: Thread plug gauge / Limit gauge FAQ What thread size does this gauge check? The limit thread plug gauge checks metric ISO fine internal threads with a nominal size of M46 x 1.5 mm (Metav IndustryLine, Article: M315.046.6). Which standard and tolerance class apply? The gauge is manufactured to DIN 13 with tolerance class 6H, ensuring conformity with common ISO metric internal thread specifications. What material is the gauge made from and how durable is it? Made from hardened gauge steel, the plug gauge is engineered for wear resistance and repeatable inspection performance in production environments. Where is this gauge typically used? The gauge is intended for workshop inspection and production quality checks, suited to machining shops, assembly inspection and incoming goods control where quick pass/fail assessment is required. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
M46×1mm Go/No-Go Thread Plug Gauge Metric ISO Fine Pitch Right Hand, Hardened Gauge Steel, DIN 13 6H - Metav IndustryLine
Take advantage of a precise, standards‑compliant inspection tool that combines DIN 13 / 6H conformity with hardened gauging steel for consistent go/no‑go checks on metric fine threads; order the gauge directly via Metav Werkzeuge or consult the technical team for application advice. Limit Thread Plug Gauge M46 × 1 — Metric ISO fine thread, right‑hand, hardened gauging steel (Metav IndustryLine) The Limit Thread Plug Gauge M46 × 1 is a right‑hand metric ISO fine‑thread gauge designed for fast, repeatable go/no‑go inspection in production environments and incoming goods control. Limit gauge for M46 × 1 metric ISO fine threads Conforms to DIN 13, tolerance class 6H Hardened gauging steel for dimensional stability Right‑hand thread for standard production checks Rapid, standards-based acceptance and rejection decisions This limit thread plug gauge provides a direct means to verify thread conformity in a production or inspection context. By applying a simple go/no‑go check with a limit thread plug gauge, operators obtain immediate, unambiguous information about the thread form and tolerance band for an M46 × 1 metric fine thread. The combination of DIN 13 geometry and 6H tolerance class offers a recognised reference frame for routine quality control; this reduces decision time at the inspection bench and lowers the risk of downstream rework. The hardened construction keeps the reference surfaces stable under repeated use, sustaining measurement integrity across production shifts. Durable construction for repeatable measurement and low maintenance Manufactured from hardened gauging steel, the gauge resists wear and maintains the declared limit dimensions over many cycles. The robust material choice minimises profile change and ensures reproducible results when used correctly in go/no‑go tests. As a simple mechanical reference, the device requires no power or electronics, which translates into predictable behaviour, easy cleaning and a low maintenance profile compared with instrumented alternatives. Where traceability is required, the gauge can be incorporated into existing inspection routines as a primary verification tool—supporting consistent product acceptance criteria without complex setup. Practical integration into quality workflows and documentation The plug‑gauge format facilitates rapid checks at the point of manufacture, in final inspection or during incoming goods control. Because the tool is a dedicated limit device rather than a measuring instrument, it removes ambiguity from pass/fail decisions and eases operator training. The compact, single‑purpose nature of the gauge simplifies storage and use alongside calibration records and inspection plans. For organisations that document compliance, the gauge’s standard reference to DIN 13 and 6H supports consistent specification language in work instructions and non‑conformity reports, helping manufacturing and quality teams communicate clearly about thread acceptance criteria. Contact Metav Werkzeuge for delivery options, calibration support and integration advice on Metav IndustryLine limit thread plug gauges. Technical Data Article number: M315.046.4 GTIN: 4054469123370 Category: Gauges — Thread plug gauges ECLASS: 21170235 Specifications Thread dimension: M46 × 1 mm Tolerance class: DIN 13, 6H Direction: Right‑hand thread Customs tariff number: 90173000 Features Material: Gauging steel, hardened Intended use: Metric ISO fine threads Type: Limit (go/no‑go) thread plug gauge Condition: Suitable for production and incoming inspection FAQ What does the M46 × 1 designation mean? The M46 × 1 designation indicates a metric thread with a nominal diameter of 46 mm and a 1 mm thread pitch; the Limit Thread Plug Gauge M46 × 1 is produced to check this specific fine‑thread form. Which tolerance does the gauge represent? The gauge is manufactured to DIN 13 with tolerance class 6H, providing a standard acceptance criterion for metric ISO threads in many engineering and production contexts. Is the gauge suitable for production use or only for sample inspection? The limit plug format is intended for both in‑process checks and incoming goods inspection; its hardened gauging steel construction supports repeated use on the shop floor for quick go/no‑go decisions. Can the gauge be used for left‑hand threads? This particular item is produced as a right‑hand thread gauge; left‑hand thread checks require a correspondingly manufactured left‑hand gauge. How is traceability documented for this gauge? Traceability is managed through standard inspection records and, where required, calibration documentation; speak with Metav Werkzeuge for recommended procedures and certification options. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
M48 x 2 mm Go Thread Ring Gauge, Right-Hand, Hardened Gauge Steel, DIN 13 6g - Metav IndustryLine
Take advantage of a hardened Go ring engineered to the DIN 13 tolerance class for reliable pass/no‑go checks, combined with a compact mass of M48 x 2 that suits metric fine‑thread inspection; order directly via Metav Werkzeuge or consult our specialists for application advice. Thread ring gauge M48 x 2 mm (Go) — Go ring for metric ISO fine thread, right‑hand (Metav IndustryLine) The Thread ring gauge M48 x 2 mm (Go) is a hardened gauge‑steel Go ring designed for rapid verification of metric ISO fine threads in production and inspection environments. Go ring for M48 x 2 metric fine thread DIN 13 tolerance class 6g for conformity Hardened gauge steel for extended durability Right‑hand thread orientation for standard applications Fast and unambiguous thread acceptance testing on the shop floor A dedicated Go ring offers a straightforward, time‑saving method to confirm whether external threads meet dimensional limits. The M48 x 2 format checks major diameter and pitch simultaneously, enabling rapid acceptance checks without measuring instruments. For assembly and incoming goods inspection this reduces cycle time and helps prevent misfits early in the process. The ring’s DIN 13 / 6g specification provides an industry‑recognised reference that integrates into documented quality procedures and supports consistent decision‑making at control stations. Robust construction for frequent handling and stable performance Manufactured from hardened gauge steel, the ring resists wear and preserves dimensional integrity over repeated use. The solid construction and a mass of approximately 1.6 kg contribute to stability and tactile feedback during go/no‑go verification. Durable surface condition and correct heat treatment mean fewer replacements and predictable service life, which in turn lowers inspection downtime and total cost of ownership. The right‑hand thread geometry matches standard thread production and checking routines, eliminating ambiguity during rapid checks. Standards compliance that supports traceable quality systems Conformity to DIN 13 and the 6g tolerance class aligns the gauge with widely accepted metric ISO fine‑thread standards, making it suitable for suppliers and production plants that require documented compliance. The gauge is supplied under the Metav IndustryLine offering and is identifiable by GTIN 4054469125091, enabling easy inventory tracking and procurement. Use of standardised gauges simplifies audit trails and ensures measurement procedures remain consistent across multiple workplaces. Practical integration into inspection workflows The Go ring is intended for quick acceptance testing rather than detailed dimensional analysis. Used at receiving, pre‑assembly or final inspection points, the ring eliminates time‑consuming micrometric measurements when the criterion is simple pass/no‑pass. For components that must mate reliably with mating parts, applying this dedicated ring as a first control step reduces scrap and rework. The compact design also makes storage and handling straightforward within standard inspection kits. Contact Metav Werkzeuge for specification support or to secure the M48 Go ring gauge from our Emmerich warehouse — phone +49 2822 7131930 or email info@metav-werkzeuge.com Technical data Article number: M315.148.7 GTIN: 4054469125091 Tariff number: 90173000 Figures Weight: 1.6 kg Thread size: M48 x 2 Pitch: 2 mm Diameter nominal: 48 mm Tolerance class: 6g Special features Material: hardened gauge steel Standard: DIN 13 Type: Go ring gauge Thread direction: right‑hand FAQ What thread form and size does this gauge check? The ring checks a metric ISO fine thread in M48 x 2 format; it verifies major diameter and pitch conformity for this specific size. Is the gauge suitable for production acceptance testing? Yes, the Thread ring gauge M48 x 2 mm (Go) is intended for rapid production acceptance and incoming inspection as a pass/no‑go reference. What material is the gauge made from and how does that affect service life? Manufactured from hardened gauge steel, the gauge offers high wear resistance and stable dimensions during repeated checks, extending service life under normal shop‑floor use. Does the ring conform to recognised standards? The gauge is specified to DIN 13 with tolerance 6g, aligning it with standard metric ISO fine‑thread inspection practices. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
M48x1 Go/No-Go Thread Plug Gauge For Metric ISO Fine Thread, Right Hand, Hardened Gauge Steel, DIN 13 6H - Metav IndustryLine
The provided product data contains contradictory entries and cannot be used to generate a reliable product description. Specifically, the dataset shows inconsistent quality indicators — one field marks the item as rejected while another flags it as good — and there are notable discrepancies between the price-related values. These conflicting entries prevent trustworthy classification and technical presentation, as key decisions (for example whether the item is sellable or requires rework) depend on accurate quality and pricing information. Please verify and correct the source fields, particularly the quality flags and price values, and resubmit the updated data. Once the contradictions are resolved, a full, standards-compliant description in British English can be produced, including correct material, standard references and the appropriate classification for metrological use.
M48x1 Thread Go Gauge Metric ISO Fine Pitch Right-Handed Hardened Gauge Steel DIN 13, 6g - Metav IndustryLine
Take advantage of precise conformity checking, durable hardened gauge steel and clear acceptance criteria to keep production moving with confidence; order the thread ring gauge directly via Metav Werkzeuge or contact our consultants for specification advice. Thread ring gauge M48 x 1 mm (Go) — Go ring gauge, DIN 13, Metav IndustryLine The thread ring gauge M48 x 1 mm (Go) is a dedicated inspection tool for rapid verification of metric ISO fine threads in production and quality assurance. Hardened gauge steel construction For metric ISO fine thread M48 x 1 Tolerance class DIN 13, 6g Reliable conformity control for fine threads The thread ring gauge M48 x 1 mm (Go) provides an unequivocal go/no‑go indication for metric ISO fine threads, simplifying acceptance checks on the shop floor. Compliant with DIN 13 and manufactured to 6g tolerance, the gauge confirms that external threads meet the specified form and pitch before assembly or coating. This direct verification step reduces uncertain rework and prevents downstream assembly defects, supporting consistent process quality. Faster inspection, less downtime Using a dedicated go ring saves valuable inspection time compared with profile measurement or comparator methods; the approach is immediate and repeatable. The clear pass condition of a go gauge accelerates throughput during batch checks and first‑off inspections, which improves line efficiency and lowers non‑conformance rates. Where cycle time and traceability matter, this gauge is a pragmatic tool for quick, defensible acceptance testing. Built for durability and practical handling Constructed from hardened gauge steel, the ring is engineered for long service life under frequent use. The unit's right‑hand thread form and balanced mass (approx. 1.6 kg) give a reassuring tactile feel during manual checking and reduce the risk of deformation under normal handling. Robust material choice and sound manufacture ensure the gauge remains reliable across repeated checks in production environments with routine cleaning and care. For fast, dependable thread inspection and procurement assistance, contact Metav Werkzeuge to discuss the Metav IndustryLine ring gauge and its suitability for current production needs at info@metav-werkzeuge.com or +49 2822 7131930 Technical data Article number: M315.148.4 GTIN: 4054469125077 Description: Thread ring gauge M48 x 1 mm (Go) Weight: 1.6 kg Facts Thread size: M48 x 1 mm Tolerance class: 6g Standard: DIN 13 Tariff number: 90173000 Special features Go gauge for metric ISO fine threads Right‑hand thread Material: gauge steel, hardened Category: Gauges; Measuring pins FAQ What does "Go" mean for this ring gauge? A Go designation indicates the ring is an acceptance gauge: the external thread should fit into the Go ring if it meets the specified limits. The ring confirms conformity for the relevant metric ISO fine thread. Which standard and tolerance does the gauge follow? The gauge is manufactured to DIN 13 with a tolerance class of 6g, suitable for standard metric ISO fine thread verification. Is this gauge suitable for production checks on M48×1 parts? Yes, the ring is specifically sized for M48 x 1 mm external threads and is intended for routine shop‑floor or incoming inspection work. How robust is the gauge for frequent use? Made from hardened gauge steel, the construction provides long‑term stability and wear resistance for regular verification tasks. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
M48x1 Thread Ring Gauge Go Metric ISO Fine Thread Right Hand, Hardened Gauge Steel, DIN 13 6g - Metav IndustryLine
Take advantage of the hardened gauge steel construction, DIN 13 / 6g tolerance and precise M48 × 1 mm thread control to keep production checks fast and reproducible. Order the gauge directly via Metav Werkzeuge or request advice from our consultants for integration into quality control routines. Thread ring gauge M48 x 1 mm — No‑go ring, DIN 13, Metav IndustryLine The thread ring gauge M48 x 1 mm is a hardened, right‑hand metric ISO fine‑thread gauge intended for go/no‑go verification in production and incoming inspection of threaded components Hardened gauge steel construction Conforms to DIN 13, tolerance 6g For M48 × 1 mm metric fine threads Reliable pass/fail control that saves rework A no‑go ring gauge provides an unambiguous, tactile check that threads do not exceed specified limits; combining hardened gauge steel with the DIN 13 / 6g class ensures mechanical stability and repeatability during high‑volume checks. The compact, single‑piece design minimises handling complexity and reduces cycle time for routine inspections. In practice, a clearly defined no‑go control prevents oversized threads from entering assemblies, lowering rework rates and protecting downstream processes from fitment faults. Clear conformity and simple interpretation for production teams The ring is manufactured to the ISO metric fine‑thread geometry for M48 × 1 mm and is intended as the counterpart to a go gauge in a two‑step verification process. Because the gauge is a go/no‑go type, measurement does not require complex instruments—checks are performed directly at the workbench or on the shop floor with immediate binary results. This approach supports traceable quality workflows and reduces reliance on subjective visual inspection, which is especially valuable during fast production runs or incoming goods inspection. Durable design for workshop and inspection use Constructed from hardened gauge steel, the ring resists wear and maintains dimensional integrity over prolonged use, preserving the defined thread limit. The solid build and balanced mass (0.94 kg) help stabilise the ring during manual engagement, reducing oscillation and false readings. For traceability, the gauge is supplied with essential identifiers so it can be incorporated into regular inspection schedules and calibrated routines, supporting consistent quality assurance across batches. For precise control of M48 × 1 mm threads and expert advice on implementing this Metav IndustryLine no‑go ring gauge in production, contact Metav Werkzeuge for availability and tailored recommendations. Technical data Article number: M315.248.4 GTIN: 4054469126739 Manufacturer: Metav IndustryLine SKU: M315.248.4 Facts Thread size: M48 × 1 mm Pitch: 1 mm Weight: 0.94 kg Tariff number: 90173000 Special features Material: gauge steel, hardened Standard: DIN 13, tolerance 6g Right‑hand, metric ISO fine thread Designated as the no‑go ring (Aussch.) FAQ What is the intended use of this ring gauge? The ring gauge is designed for go/no‑go verification of M48 × 1 mm ISO metric fine threads; it serves as the no‑go control to ensure threads are not oversized. Does the gauge comply with recognised standards? Yes. The ring is manufactured to DIN 13 with a 6g tolerance class suitable for metric ISO fine threads. What material is used for the gauge and why does it matter? The gauge is made from hardened gauge steel, which ensures wear resistance and dimensional stability for repeated inspection cycles. Can this ring gauge be used on left‑hand threads? No. This particular gauge is specified for right‑hand metric ISO fine threads and will not match left‑hand thread profiles. How should the ring gauge be integrated into a quality workflow? Use it as part of a two‑step go/no‑go verification routine during incoming inspection or final assembly checks to provide immediate pass/fail results and reduce downstream rejects. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
M48x1.5 Go/No-Go Thread Plug Gauge Metric ISO Fine Pitch Right-Hand, Hardened Gauge Steel, DIN 13 6H - Metav IndustryLine
Take advantage of precise, standard‑compliant inspection with a hardened limit thread plug gauge for metric fine threads; the combination of DIN 13 conformity, hardened gauge steel and clear go/no‑go verification keeps quality control efficient and reproducible — order directly via Metav Werkzeuge or consult the team for specification support. Limit thread plug gauge M48 x 1.5 — right‑hand, DIN 13, 6H (Metav IndustryLine) Limit thread plug gauge M48 x 1.5 for rapid verification of metric ISO fine threads in production and incoming inspection DIN 13 compliance, tolerance class 6H Hardened gauge steel construction For M48 x 1.5 metric fine thread verification Consistent, standards‑based thread acceptance for production lines The M48 x 1.5 limit thread plug gauge is manufactured to DIN 13 and tolerance class 6H, providing a reliable, standards‑based pass/fail check for metric fine threads. As a limit thread plug gauge, it offers a fast, unambiguous method to confirm internal thread conformity: the "go" end verifies correct form and fit, while the "no‑go" end confirms that the thread does not exceed maximum material limits. This approach reduces interpretation error in routine checks and supports traceable quality assurance procedures on the shop floor. Durable design for repeatable inspection cycles Constructed from hardened gauge steel, the gauge withstands repeated use and retains dimensional stability over long inspection cycles. The right‑hand geometry and robust machining deliver consistent engagement with internal threads, reducing the need for frequent replacement and lowering downtime. Weight and massing have been optimised for hand inspection: the solid build provides tactile feedback during insertion, improving operator confidence and minimising measurement variation between shifts. Practical integration with workshop quality workflows The plug gauge is intended for direct use in production and incoming goods routines where quick decisions are required. Its clear pass/fail function shortens inspection time compared with full thread measurement, supporting higher throughput without sacrificing control. When used as part of a documented inspection routine, the gauge helps maintain reproducible results and supports corrective actions when process drift is detected, enabling engineering teams to react to deviations more rapidly. Proven supplier reliability and application guidance The item is offered under Metav IndustryLine and carries the internal reference M315.048.6, aligning supplier traceability with workshop practice. Metav’s distribution and quality controls act as a practical filter for the European market, supplying precision tools that meet industrial expectations. For procurement and specification planning, selecting a limit thread plug gauge that matches the thread standard and tolerance class simplifies inventory and ensures compatibility with standardised production threads. Contact Metav Werkzeuge today for specification advice or to secure the Metav IndustryLine M315.048.6 limit thread plug gauge for immediate integration into inspection routines Technical Data Article number: M315.048.6 GTIN: 4054469123417 Weight: 1.3 kg Category: Lehren / Messstifte Facts Thread size: M48 x 1.5 Tolerance class: 6H Norm: DIN 13 Tariff number: 90173000 Special features Material: hardened gauge steel Right‑hand thread design Limit thread plug gauge (go / no‑go verification) ECLASS: 21170235 FAQ What thread standard does this gauge check? The gauge checks metric ISO fine threads according to DIN 13 with tolerance class 6H, as specified for the Limit thread plug gauge M48 x 1.5. Is this a go/no‑go instrument? Yes. The M315.048.6 is a limit thread plug gauge designed for go/no‑go verification of internal threads. What material is the gauge made from? The gauge is manufactured from hardened gauge steel, chosen for wear resistance and long service life. Is the gauge suitable for right‑hand threads only? The supplied unit is a right‑hand gauge for the M48 x 1.5 thread form. Can this gauge be used for laboratory calibration tasks? The gauge is intended for production and incoming inspection as a pass/fail device; for laboratory calibration or dimensional measurement, complementary calibrated reference tools are typically used. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
M48x1.5 Thread Ring Gauge Right-Hand ISO Metric Fine Thread DIN 13, Hardened Gauge Steel - Metav IndustryLine
Robust hardened gauge steel and the DIN 13 tolerance class ensure repeatable verification of metric fine threads; the M48 × 1.5 no‑go ring reliably identifies out‑of‑tolerance components and reduces rework. Order the thread ring gauge directly via Metav Werkzeuge or consult the technical team for integration advice. Thread ring gauge M48 × 1.5 mm — hardened gauge‑steel ring for metric ISO fine threads, right‑hand The Thread ring gauge M48 × 1.5 mm is a hardened inspection ring designed to check right‑hand metric ISO fine threads according to DIN 13, tolerance 6g, for dependable workshop and production control. Hardened gauge steel for long service life Conforms to DIN 13, tolerance class 6g Suitable for M48 × 1.5 mm metric ISO fine thread Ensure conformance with a compact inspection tool A hardened thread ring gauge provides a quick, objective check of external threads. Built from hardened gauge steel, this ring resists wear and preserves gauge limits over many cycles, which directly supports consistent pass/fail decisions at the production line. Because the gauge is specified to DIN 13 with tolerance 6g, inspection results align with common machine‑building and assembly standards, simplifying acceptance criteria and reducing ambiguous measurements. The compact form factor and clear nominal size make the ring straightforward to incorporate into final inspection stations or quick checks at machineside. Reduce rework and protect assembly quality Using a dedicated no‑go ring for the specified metric fine thread prevents incorrectly sized parts from entering assembly. The mechanical design requires only a simple manual check: if the ring does not fit the external thread, the part is rejected. This low‑complexity method saves time compared with full dimensional inspection, while offering high reliability for thread conformity. The hardened construction maintains the gauge boundary over repeated use, so sampling intervals can be optimised and downtime for gauge replacement is minimised. For process control, this translates into lower scrap rates and fewer assembly faults. Practical integration into workshop routines The ring is intended for right‑hand metric ISO fine threads and is sized M48 × 1.5 mm to match common fine‑pitch applications. Its weight and robust material make it suitable for bench storage or line‑side use; a stable handling routine keeps results reproducible. For traceable quality systems, record the gauge identification and inspection outcomes in the production log; the clear standard marking (DIN 13, 6g) supports audits and cross‑checks with inspection plans. For bespoke setups or fixture use, the ring's form factor allows straightforward clamping or holder adaptation without altering its metrological function. Contact Metav Werkzeuge today for specification matching and to secure the hardened M48 × 1.5 mm thread ring gauge for reliable thread inspection. Technical data Article number: M315.248.6 SKU: M315.248.6 GTIN: 4054469126746 Nominal size: M48 × 1.5 Material: hardened gauge steel Standard: DIN 13, 6g Thread direction: right‑hand Weight: 0.94 kg Facts Nominal diameter: 48 mm Thread pitch: 1.5 mm Tolerance class: 6g Standard reference: DIN 13 Mass: 0.94 kg Special features Type: no‑go ring for external thread inspection Category: thread ring gauge Durable hardened measuring surface Suitable for metric ISO fine threads FAQ What does the M48 × 1.5 marking mean? The marking indicates a nominal diameter of 48 mm with a thread pitch of 1.5 mm, matching the standard metric fine thread form used for inspection with this ring gauge. Is this ring gauge suitable for left‑hand threads? No; the ring is manufactured for right‑hand metric ISO fine threads and is intended to be used on matching right‑hand external threads. How does DIN 13, 6g affect inspection decisions? DIN 13 with tolerance class 6g defines the permissible limits for the nominal external thread; the ring gauge is manufactured to that standard so pass/fail checks correspond to accepted assembly limits. Can the ring be used as a go gauge? This specific item is supplied as a no‑go ring for verifying that threads do not exceed the upper tolerance; go/no‑go decisions depend on the type of ring supplied. What maintenance is required to preserve accuracy? Keep the gauge clean, avoid shocks, and store it in a protective location; the hardened steel construction reduces wear but routine visual checks and periodic calibration are recommended for traceable inspection regimes. Metav IndustryLine: Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
M48x1.5 Thread Ring Gauge, Go, Right-Hand, Hardened Gauge Steel, DIN 13 6g - Metav IndustryLine
Take advantage of the combination of hardened gauge steel construction, DIN 13 tolerance class 6g and the clear go/no‑go decision the tool provides for M48 × 1.5 threads to keep production checks fast and reliable. Order the gauge via Metav Werkzeuge or contact our consultants for application-specific advice. Go ring gauge M48 x 1.5 mm (DIN 13, 6g) – Thread ring gauge by Metav IndustryLine A Go ring gauge M48 x 1.5 mm for right‑hand metric ISO fine threads, designed for fast pass/fail inspection in production and incoming goods control Hardened gauge steel construction DIN 13 tolerance class 6g Quick pass/fail check for M48×1.5 Consistent, unambiguous thread acceptance for production lines A dedicated Go gauge delivers immediate decisions at the inspection point: the part either passes through the ring or it does not. This particular ring, sized M48 x 1.5 mm and manufactured to DIN 13 with tolerance 6g, is optimised for metric ISO fine threads and right‑hand applications. The straightforward mechanical check minimises operator interpretation and cycle time, supporting higher throughput and reduced rework rates. In routine quality control, such a tool is the most efficient way to verify that external threads meet the maximum material condition required for assembly. Robust construction for repeatable measurements and long service life Made from hardened gauge steel, the ring resists wear and preserves its calibrated form under frequent use. The solid construction and the gauge’s mass contribute to stable handling and repeatability during tactile checks on the shop floor. Compliance with the DIN 13 specification ensures the gauge corresponds to recognised dimensional and form criteria, making it suitable for both production checks and goods‑in inspection where traceable, repeatable performance is essential. Simple integration into inspection routines and documentation The ring gauge is a tactile, single‑function instrument well suited to sample testing, end‑of‑line checks and rapid acceptance testing in assembly areas. Its mechanical nature requires no power or software, which simplifies handling and traceability in regulated environments. Where documentation is required, the gauge’s specification (thread size, pitch and tolerance class) can be recorded alongside batch and operator data to support quality records and audits, contributing to a clear, auditable inspection process. Contact Metav Werkzeuge for technical advice and to obtain the Metav IndustryLine Go ring gauge M48 x 1.5 mm for immediate integration into the inspection workflow Technical data Article number: M315.148.6 GTIN: 4054469125084 Weight: 1.6 kg Thread size: M48 x 1.5 mm Direction: Right‑hand Standard: DIN 13, 6g Material: Gauge steel, hardened Facts Nominal diameter: 48 mm Thread pitch: 1.5 mm Tolerance class: 6g Mass: 1.6 kg Special features Go (pass) ring for metric ISO fine threads Right‑hand thread application Hardened gauge steel construction Compliance with DIN 13 FAQ What does "Go" mean on this ring gauge? The term "Go" indicates the ring is a pass gauge: the external thread (e.g. a bolt) must enter the Go ring gauge M48 x 1.5 mm without interference to be accepted; it verifies that the external thread does not exceed the maximum material condition. Which standard does the gauge follow? This Metav IndustryLine ring is manufactured to DIN 13 and specified for tolerance class 6g, matching common requirements for metric ISO external threads. What material is the gauge made from and why does it matter? The ring is made from hardened gauge steel, providing wear resistance and long‑term dimensional stability so that the gauge sustains repeatable performance during frequent checks. Can this gauge be used for production and incoming inspection? Yes. The Go ring gauge M48 x 1.5 mm is intended for both shop‑floor production checks and incoming goods inspection where a clear pass/fail decision is required. What is the article number for ordering or referencing? Reference article number M315.148.6 (GTIN 4054469125084) when ordering the Metav IndustryLine Go ring gauge M48 x 1.5 mm. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
M48x2 Gauge Ring Thread Plug Right-Hand ISO Metric Fine Pitch DIN 13, Hardened Gauge Steel - Metav IndustryLine
Precision-tested hardened gauge steel and conformity to DIN 13 (6g) make this gauge ring a dependable choice for repeatable thread verification; compact M48 x 2 geometry suits metric ISO fine threads and supports consistent production control. Order the thread ring gauge directly via Metav Werkzeuge or consult our advisors for specification support. Thread Ring Gauge M48 x 2 — Hardened Gauge Steel, DIN 13 — Metav IndustryLine A Thread Ring Gauge M48 x 2 designed for fast, repeatable inspection of metric ISO fine threads in manufacturing and incoming quality control. Hardened gauge-steel construction Metric ISO fine thread M48×2 Tolerance DIN 13 — 6g Right-hand thread for standard checks Precision and compliance that reduce inspection uncertainty The ring is manufactured from hardened gauge steel, providing a wear-resistant contact surface that preserves the original geometry even under frequent use. Built to DIN 13 with a 6g tolerance, the gauge offers a clear, standardised benchmark for pass/fail decisions on M48 x 2 metric ISO fine threads; this removes ambiguity from visual checks and supports faster, evidence-based quality decisions. The combination of standard conformity and robust material reduces rework and non‑conforming parts in serial production. Durability and handling that keep workshop throughput steady Designed for shopfloor conditions, the ring’s hardened construction and compact form factor ensure long service life without complex maintenance. The tool’s mass and geometry provide stable seating during inspection, improving repeatability and reducing operator-induced variation. Where frequent thread checks are required, this stability shortens cycle times and contributes to a smoother production flow while lowering the risk of false rejects. Integration into quality workflows and traceability The gauge is suitable for routine incoming inspection, in‑process checks and final verification of metric ISO fine threads. Its clear designation to M48 x 2 and compliance with DIN 13 (6g) allow straightforward documentation in quality records and audit trails. When used as part of a structured inspection plan, the ring supports traceable measurement routines and helps maintain consistent batch quality across suppliers and production runs. For reliable thread inspection with Metav IndustryLine precision, contact Metav Werkzeuge for product advice and to arrange supply directly via info@metav-werkzeuge.com or +49 2822 7131930 Technical data Article number: M315.248.7 SKU: M315.248.7 GTIN: 4054469126753 Weight: 0.94 kg Size: M48 x 2 Standard: DIN 13, 6g Tariff number: 90173000 Manufacturer brand: Metav IndustryLine Facts Material: Hardened gauge steel Thread direction: Right-hand Category: Gauges / Ring gauge Special features Designed for metric ISO fine threads Robust, wear-resistant construction Suitable for incoming and in-process inspection FAQ What thread form does this gauge check? The thread ring gauge checks metric ISO fine threads in the M48 x 2 form and is specified for right-hand threads. Is the ring suitable for production spot checks and final inspection? Yes. The M48 x 2 ring gauge is intended for routine spot checks, in‑process control and final verification in production and incoming inspection. What does DIN 13, 6g mean for the user? DIN 13 defines metric thread tolerances; the 6g indication specifies the tolerance class used for the ring, providing a standardised acceptance criterion for M48 x 2 threads. Which material is used and why does that matter? Manufactured from hardened gauge steel, the ring offers wear resistance and long-term dimensional stability, which preserves inspection accuracy over many cycles. Can this gauge be used as a master for calibration routines? The gauge provides a repeatable reference for everyday inspections; for calibration masters used in laboratories, a dedicated calibrated standard appropriate to the lab’s scope is recommended. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
M48x2 Limit Plug Gauge For Metric ISO Fine Thread, Right-Hand, Hardened Gauge Steel, DIN 13 6H - Metav IndustryLine
The supplied product data contains contradictory quality information: the item is simultaneously flagged as scrapped and as being in good condition. Because of this inconsistency, a reliable, production-ready product description cannot be generated. Please clarify whether the article is intended as usable stock or as rejected material, and provide the correct status along with any relevant inspection or certification documents. Once the condition and metadata are corrected, a complete, standards-compliant technical description and sales text can be produced promptly, using the appropriate industrial terminology and calibration details. For help resolving the discrepancy, contact Metav Werkzeuge by e‑mail at info@metav-werkzeuge.com or by telephone on +49 2822 7131930.
M48x3 Thread Go/No-Go Plug Gauge Metric ISO Fine Thread Right Hand, Hardened Gauge Steel, DIN 13 6H - Metav IndustryLine
Combining DIN‑compliant tolerances with hardened gauge steel and a compact, balanced weight ensures dependable pass/fail assessment for ISO metric fine threads; order the gauge directly from Metav Werkzeuge or consult their specialists for application advice. Limit thread plug gauge M48 x 3 — ISO metric fine thread, hardened gauge steel (Metav IndustryLine) Limit thread plug gauge M48 x 3 checks ISO metric fine threads for production and incoming inspection applications, right‑hand design for standard thread verification Limit thread plug gauge M48 x 3, right-hand Hardened gauge steel for long-term accuracy Manufactured to DIN 13, tolerance 6H Suitable for production and inspection use Consistent passage checks for process reliability A compact, purpose‑made plug gauge offers a fast, unequivocal test during machining and assembly. The M48 x 3 size is matched to ISO metric fine‑threaded components and provides a binary assessment via go/no‑go fit, enabling immediate decisions on part conformity. Because the gauge is produced from hardened gauge steel, wear resistance and dimensional stability extend service life, reducing the need for frequent replacement and supporting uninterrupted production throughput. Designed to reduce inspection variability The right‑hand limit thread plug gauge is finished to DIN 13 with a declared tolerance zone 6H, which aligns inspection practice with standard thread specifications. This alignment removes guesswork from everyday checks: a successful pass on the "go" end guarantees assembly compatibility, while a fail on the "no‑go" end highlights threads that require rework. The straightforward mechanical principle of the gauge delivers rapid throughput in quality control without reliance on complex measuring equipment. Traceable standards and operational benefits Using a standardised thread gauge simplifies documentation and audit trails in manufacturing and inspection. The go/no‑go method reduces measurement time per part and supports statistical process control by providing repeatable results. For workshop environments where clear decisions are needed quickly, the gauge helps to maintain cycle time and minimise scrap. The weight and mass distribution also favour stable handling during frequent routine checks. Robust construction for everyday workshop use Made from hardened gauge steel, the tool resists surface damage that would otherwise degrade performance; this supports long‑term accuracy and predictable maintenance intervals. The compact design and fixed geometry make the gauge easy to store and use at the point of inspection, while the balanced mass (approx. 1.3 kg) gives a reassuring feel that aids controlled application. For manufacturers and inspection teams seeking a low‑complexity solution, this gauge offers reliability without the need for specialised measuring instruments. Contact Metav Werkzeuge for bespoke inspection recommendations and prompt supply from Emmerich — phone +49 2822 7131930 or email info@metav-werkzeuge.com Technical data Article number: M315.048.8 GTIN: 4054469123431 Brand: Metav IndustryLine Country of origin: Germany Core measurements Thread: M48 x 3 Tolerance/class: 6H Standard: DIN 13 Weight: 1.3 kg Tariff number: 90173000 Features and applications Right‑hand metric fine thread verification Hardened gauge steel construction Binary go/no‑go inspection principle For production control and incoming inspection FAQ What is the intended use of this limit thread plug gauge? The limit thread plug gauge is intended for rapid go/no‑go verification of ISO metric fine threads in production and inspection environments, verifying conformity to DIN 13 with tolerance 6H. Can the gauge be used for both assembly checks and incoming inspection? Yes, the plug gauge is suitable for both assembly compatibility checks and incoming inspection tasks; its go/no‑go principle delivers clear pass/fail results for routine quality control. How does the DIN 13, 6H classification affect inspection? DIN 13 with class 6H defines the thread form and tolerance band; using a gauge manufactured to that standard ensures the checked parts meet the accepted thread fit and assembly requirements. What material is the gauge made from and why does it matter? The gauge is manufactured from hardened gauge steel, which provides wear resistance and dimensional stability, maintaining accuracy over repeated use in workshop conditions. Is this gauge appropriate for fine thread sizes only? This particular item is sized for M48 x 3, a metric fine thread; the design and tolerances are matched to that pitch and diameter for reliable verification. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
M48x3 Thread Plug Gauge ISO Fine Pitch Right-Handed Hardened Gauge DIN 13, 6g - Metav IndustryLine
Take advantage of a precise, workshop-ready inspection tool that combines hardened gauge steel, conformity to DIN 13 (6g) and the defined M48 x 3 mm metric fine thread class for reliable pass/fail verification on external threads. Order the gauge directly via Metav Werkzeuge or ask our consultants for application advice. Thread ring gauge M48 x 3 mm – hardened gauge steel, DIN 13 (6g) The thread ring gauge M48 x 3 mm is a right‑hand metric ISO fine thread gauge for fast, repeatable verification of external threads in manufacturing and inspection environments. Hardened gauge steel construction DIN 13 tolerance class 6g Metric fine thread M48 x 3 mm Right‑hand, workshop-ready Fast conformity checks for metric fine threads A compact ring gauge such as this is designed for straight‑forward verification of external threads with the clear objective of confirming conformity to the DIN 13 specification. Built for routine production checks, the device gives immediate, unambiguous results that accelerate quality control: parts are accepted when the gauge fits and rejected when it does not. This direct form of verification reduces measurement time and avoids interpretation errors associated with indirect inspection methods, improving throughput without sacrificing traceability. Durable construction that reduces rework and downtime Manufactured from hardened gauge steel, the component combines dimensional stability with wear resistance to withstand repeated engagement with threaded parts. The solid construction and a mass of 0.94 kg provide a reassuring feel and support consistent engagement, which preserves the 6g tolerance class across long production runs. The material choice minimises the frequency of replacement and helps maintain production continuity, lowering hidden costs associated with replacement and rework. Suitable for machine shops and assembly lines Engineered specifically for metric ISO fine threads, the gauge supports verification where high repeatability matters—such as assembly of precision housings, hydraulic components or demanding fastener applications. The right‑hand orientation and the M48 x 3 mm thread size make it suitable for a wide range of components commonly produced in metalworking shops. Integration into routine inspection stages is straightforward and contributes to a reliable quality gate in the production process. Practical handling and storage for everyday use Despite being robust, the gauge is sized for practical handling during repetitive checks; the ring form factor allows quick engagement with external threads and easy stowage in a tool tray. The clear identification by standard (DIN 13, 6g) and the manufacturer SKU ensure unambiguous use in the workshop and stock management. For specialised traceability requirements, Metav can advise on labelling and storage options that protect the gauge and preserve its conformity over time. Contact Metav Werkzeuge for tailored advice, availability from our Emmerich quality hub and assistance matching this ring gauge to inspection routines in the workshop Technical data Article number: M315.248.8 GTIN: 4054469126760 Manufacturer: Metav IndustryLine Tariff number: 90173000 Facts Thread: M48 x 3 mm Weight: 0.94 kg Tolerance class: 6g Standard: DIN 13 Special features Material: hardened gauge steel Right‑hand thread Category: Gauges; Measuring instruments FAQ What is this gauge used for? This thread ring gauge M48 x 3 mm from Metav IndustryLine is used for quick verification of external metric ISO fine threads to the DIN 13, 6g tolerance class. Does the gauge indicate tolerance class and standard? Yes, the marking on the ring confirms DIN 13 and the 6g tolerance class; these identifiers make it clear which thread quality the gauge checks. Is the gauge suitable for serial production checks? The hardened gauge steel construction and robust design of the M48 x 3 mm ring gauge (SKU M315.248.8) make it well suited to routine production inspection in machine shops and assembly lines. How should the gauge be handled to preserve accuracy? Handle the gauge carefully, keep it clean and store it protected to avoid knocks; regular visual checks are recommended to ensure the ring maintains its defined fit for the specified M48 x 3 mm thread. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
M48x5 Go/No-Go Thread Plug Gauge Metric ISO Pitch Right Handed, Hardened Gauge Steel, DIN 13 6H - Metav IndustryLine
Take advantage of robust hardened gauge steel, strict DIN 13 (6H) compliance and reliable GO/NO‑GO checking to secure consistent thread acceptance across production and inspection. Order the limit thread plug gauge M48 × 5 directly via Metav Werkzeuge or ask our consultants if needed. Limit thread plug gauge M48 × 5 — Right‑hand, Metav IndustryLine The limit thread plug gauge M48 × 5 is designed for fast, repeatable verification of metric ISO regular internal threads in workshop and production environments. Hardened gauge steel construction Conforms to DIN 13, tolerance 6H For M48 × 5 metric ISO threads Right‑hand limit plug for GO/NO‑GO checking Built for dependable thread control A precision limit thread plug gauge is the quickest way to prove that internal threads meet specification. The M48 × 5 gauge is manufactured from hardened gauge steel, giving the core resistance needed for repetitive checks in a production environment. Conformity with DIN 13 and the internal tolerance class 6H ensures the acceptance geometry corresponds to the internationally established metric ISO regular thread standard. The gauge uses the established GO / NO‑GO principle: the GO section verifies the minimum material condition while the NO‑GO section checks the maximum material limit, providing immediate, unambiguous pass/fail results without additional measurement steps. Faster inspections, fewer interruptions Integrating a physical limit gauge into the inspection routine reduces cycle time compared with measurement‑based checks. The plug gauge offers instant feedback, which supports faster machine setup and minimises costly rework by catching out‑of‑tolerance threads at the earliest stage. With a compact mass of 1.3 kg, the tool remains easy to handle for operators while delivering the stiffness required for reliable engagement. Clear go/no‑go outcomes translate into improved repeatability on the shop floor, helping production teams maintain consistent quality levels throughout batch runs. Practical handling and quality provenance The gauge’s right‑hand configuration matches the prevailing thread direction on most components, so it slots directly into standard inspection workflows. The hardened construction resists wear from regular use and is straightforward to clean and store—best practice being a dry, protected case to preserve the gauge geometry. Manufactured under the Metav IndustryLine quality scheme, the instrument benefits from Metav’s role as a European precision partner, combining a broad product range with local logistics and quality control. This provenance supports traceability and procurement clarity for manufacturing and quality managers. Choose Metav IndustryLine for standard‑compliant thread control and contact Metav Werkzeuge for tailored procurement and technical advice at info@metav-werkzeuge.com or +49 2822 7131930 Technical Data Article number: M315.048 GTIN: 4054469123394 Label: Limit thread plug gauge M48 × 5 mm, right‑hand Facts Thread designation: M48 × 5 Weight: 1.3 kg Tariff number: 90173000 Tolerance class: 6H Standard: DIN 13 Special features Material: gauge steel, hardened Right‑hand thread Limit plug (GO / NO‑GO) for quick acceptance testing Intended for metric ISO regular internal threads Category: gauges / limit plug gauge FAQ What thread size does this gauge check? The limit thread plug gauge checks M48 × 5 metric ISO regular internal threads. What does the tolerance class 6H indicate? Tolerance 6H is the standard internal thread tolerance for metric ISO regular threads according to DIN 13; the gauge verifies that internal threads fall within the acceptance limits for that class. Is this gauge suitable for left‑hand threads? No, this particular instrument is a right‑hand limit plug gauge and is designed for right‑hand threads only. What material is the gauge made from and how durable is it? The gauge is made from hardened gauge steel, providing good wear resistance and stable geometry for repetitive GO/NO‑GO checks in production and inspection. How should the gauge be used in inspection? The GO section must enter the thread freely to indicate acceptance; the NO‑GO section must not fully enter if the thread is within tolerance. This provides an immediate pass/fail decision without measuring values. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
M48x5 Thread Go Ring Gauge For Metric ISO Thread, Right-Hand, Hardened Gauge Steel DIN 13 6g - Metav IndustryLine
Ensure reliable thread inspection with a hardened go ring designed for metric ISO threads; the combination of DIN 13 / 6g conformity and durable gauge‑steel construction supports fast pass/fail verification in production. Order this precision ring directly via Metav Werkzeuge or consult our specialists for application advice. Thread go ring M48 x 5 mm — hardened gauge steel, DIN 13 (Metav IndustryLine) A Thread go ring M48 x 5 mm for quick verification of metric ISO standard threads, intended as a right‑hand "go" gauge for production and quality control DIN 13 tolerance class 6g Hardened gauge steel construction For M48 × 5 mm metric ISO threads Right‑hand go ring gauge Fast, reliable conformity checks to reduce rework The primary role of this gauge is clear: provide an immediate, unambiguous check of external threads to ensure they meet the DIN 13 metric ISO profile and 6g tolerance. Manufactured from hardened gauge steel, the ring gives a wear‑resistant contact surface that preserves the gauge geometry through repetitive use. The result is a reduction in scrappage and rework costs, because parts that pass the go test can be released without time‑consuming dimensional measuring. For throughput‑driven shops, this translates into measurable uptime gains and consistent production quality. Robust construction for repeatable production use Designed for workshop and inspection environments, the ring’s hardened material and precise thread profile deliver stable results across long inspection runs. The nominal size M48 × 5 mm and right‑hand orientation correspond directly to common metric ISO applications, allowing straightforward integration into routine checks at assembly stations or in incoming goods inspection. The gauge’s mass contributes to handling stability during engagement, while the hardened surface increases service life, reducing the frequency of replacements and downtime for tool changes. Practical benefits for inspection and assembly workflows As a dedicated go ring, the component offers immediate pass/fail decision making without elaborate setup. Where tactile or visual confirmation is preferred over numerical readouts, this mechanical gauge provides a direct, operator‑friendly method to ensure thread conformity. The adherence to standard thread geometry simplifies communication with suppliers and internal production teams: a declaration of conformity against DIN 13, 6g provides a common reference that speeds decision making and reduces ambiguity in quality routines. Integration into quality assurance systems The gauge suits serial production, first‑piece inspection and spot checks on batches of fasteners or threaded parts. Its straightforward application supports shop‑floor control plans and can complement dimensional measuring equipment where full measurement is unnecessary or impractical. Paired with Metav’s catalog and advisory services, the ring becomes part of a wider strategy to democratise precision across workshops, allowing consistent checks to be carried out reliably and without complex training. For technical advice or to secure Metav IndustryLine’s hardened go ring M48 × 5 for immediate use in production, contact Metav Werkzeuge in Emmerich — our specialists will advise on suitability and delivery options Technical data SKU: M315.148 GTIN: 4054469125060 Material: gauge steel, hardened Thread size: M48 × 5 mm Direction: right‑hand (go) Norm: DIN 13, 6g Weight: 1.2 kg Tariff number: 90173000 Facts Nominal thread: M48 × 5 mm Tolerance class: 6g Mass: 1.2 kg eClass: 21170214 Special features Go (pass) ring gauge Hardened gauge‑steel construction For metric ISO standard threads Category: ring gauge (Lehre) FAQ What thread standard does this gauge check? The ring checks metric ISO threads in accordance with DIN 13 and the tolerance class 6g, ensuring compatibility with standardised metric thread production. Is the ring suitable for shop‑floor use and repetitive checks? Yes, the hardened gauge‑steel construction of the M48 × 5 mm go ring is designed for repetitive production checks and offers wear resistance for extended service life. How is the go ring used in inspection routines? The go ring is engaged with an external thread; if the part fully enters the ring without binding, it passes. This provides a fast pass/fail decision useful for inline and incoming inspection. Does the product come calibrated or with a certificate? This product is supplied as a precision go ring compliant with the stated standard. Specific calibration certificates are not included by default unless otherwise specified in the product offer. Which applications are typical for this ring gauge? Typical uses include incoming goods inspection, assembly verification and spot checks on threaded components in manufacturing and maintenance contexts. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
M48×3 Thread Gauge Ring Go Metric ISO Fine Thread Right Hand DIN 13, 6g Hardened Gauge Steel - Metav IndustryLine
Combine DIN 13 compliance, hardened gauge steel construction and compact mass for reliable, repeatable thread inspections; order direct via Metav Werkzeuge or consult our specialists for integration into production control. Thread ring gauge M48 x 3 mm (Go) — ring gauge, DIN 13, 6g (Metav IndustryLine) A thread ring gauge M48 x 3 mm Go designed for quick verification of metric ISO fine threads in production and inspection environments For M48 x 3 mm metric fine threads DIN 13, tolerance class 6g Hardened gauge steel for durability 'Go' ring gauge for quick pass/fail check Consistent conformity to DIN standards for traceable checks The DIN 13 specification and 6g tolerance class ensure that the gauge provides a clear, standards‑based reference for thread acceptance. As a Go ring gauge, it confirms whether an external thread meets the nominal geometry and the permitted tolerance band for an M48 x 3 mm pitch; parts that pass the Go check can proceed in the process without time‑consuming dimensional rework. This standardised approach supports reproducible quality control and simplifies inspection protocols in workshop and shop‑floor contexts. Robust construction for long service life in the workshop Manufactured from hardened gauge steel, the ring gauge resists wear and maintains its measuring edge over prolonged use, reducing the need for frequent replacement. The compact 1.6 kg mass gives sufficient rigidity for a stable feel during manual checks while remaining manageable for routine handling. The right‑hand thread design matches standard thread direction and allows immediate functional checks; the sturdy build and material choice contribute to low life‑cycle costs and dependable performance under repeated use. Faster inspection, fewer rejects, higher throughput Using a dedicated ring gauge accelerates acceptance decisions and integrates neatly into quality workflows: pass/fail results are instantaneous, supporting lean inspection steps and minimising throughput delays. The gauge is suitable for production control of metric ISO fine threads and works well alongside go/no‑go tooling and dimensional documentation to create an auditable inspection chain. Confidence in component conformity reduces rework, improves first‑time yield and gives production managers clear evidence for process stability. For reliable thread inspection and to discuss suitability for specific parts, request the Metav IndustryLine M48 x 3 mm Go ring gauge from Metav Werkzeuge; our Emmerich team can advise on delivery and workshop integration — email info@metav-werkzeuge.com or call +49 2822 7131930 Technical Data Article number: M315.148.8 GTIN: 4054469125107 Manufacturer: Metav IndustryLine Thread: M48 x 3 mm Tolerance/standard: DIN 13, 6g Material: gauge steel, hardened Weight: 1.6 kg Tariff number: 90173000 Facts Nominal diameter: 48 mm Thread pitch: 3 mm Tolerance class: 6g Standard reference: DIN 13 Mass: 1.6 kg Special features Go ring gauge for pass/fail inspection Right‑hand thread Suitable for metric ISO fine threads Hardened gauge steel construction Intended for production and inspection environments FAQ What is the primary use of this ring gauge? The ring gauge verifies external threads: the M48 x 3 mm Go ring gauge from Metav IndustryLine is used to check whether metric ISO fine threads meet the nominal geometry and the DIN 13, 6g tolerance. Does this gauge check left‑hand threads? No, this particular gauge is manufactured for a right‑hand M48 x 3 mm thread. What material is the gauge made from and why does that matter? The gauge is made from hardened gauge steel, which provides wear resistance and dimensional stability for repeated use in workshop inspections. Is the M48 x 3 mm gauge suitable for production use? Yes, the gauge is designed for production and inspection environments where quick Go/No‑Go checks speed up quality control and reduce rework. How should the gauge be stored to maintain accuracy? Store the gauge in a clean, dry place away from impact and corrosive agents; regular visual checks for wear and adherence to company calibration schedules preserve accuracy. Metav IndustryLine: Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
M48×5 Thread Ring Gauge 6g Right-Hand Hardened Gauge Steel DIN 13 - Metav IndustryLine
Reliable thread verification for M48 × 5 metric ISO threads is guaranteed by hardened gauge steel and DIN 13 tolerance class 6g; the no‑go ring simplifies fast go/no‑go checks and supports consistent quality control. Order this thread ring gauge directly via Metav Werkzeuge or consult Metav’s specialists for application advice. Thread ring gauge M48 × 5 mm — no‑go ring, hardened gauge steel (DIN 13, 6g) — Metav IndustryLine Thread ring gauge M48 × 5 mm (no‑go) for rapid verification of metric ISO threads in production and inspection environments Hardened gauge steel construction DIN 13 tolerance class 6g For M48 × 5 metric ISO threads Right‑hand thread checking tool Consistent pass/fail control to keep production moving The thread ring gauge is designed for fast and unequivocal verification of internal thread quality on components with an M48 × 5 pitch. Constructed from hardened gauge steel, the ring provides mechanical stability and wear resistance that support repeated use on the shop floor. With the DIN 13 specification and 6g tolerance class engraved into the tool, operators gain a clearly defined reference for acceptance criteria; this reduces subjective judgement in inspection and helps to prevent downstream assembly issues. The no‑go function ensures that any part failing the dimensional or form limits is identified immediately, helping to protect assembly lines from out‑of‑tolerance parts. Practical benefits for workshop and quality control Using this inspection ring simplifies routine checks: the geometry verifies thread flank form and pitch in a single, tactile operation, making it suitable for rapid sampling during batch production or incoming inspection. The right‑hand orientation matches standard metric ISO threads and the compact ring form factor makes it easy to handle at control stations. Because the tool is a dedicated go/no‑go reference, measurement time is reduced and throughput improves — a rational advantage for manufacturing environments where speed and repeatability translate directly into lower rework rates and fewer production interruptions. Built for durability and straightforward integration Durable hardened gauge steel minimises wear and maintains the gauge form over long service intervals, which supports consistent results and long‑term reliability. The ring’s nominal size marking and conformity to DIN 13 provide clear traceability in inspection records and process documentation. Lightweight handling and a compact footprint make the gauge simple to incorporate into existing inspection jigs or handheld checking routines. As a specialised verification tool, the ring complements dimensional measuring equipment by providing a rapid go/no‑go reference that is easy to interpret without additional instruments. Contact Metav Werkzeuge for expert advice and to request the M48 × 5 no‑go thread ring for delivery from Emmerich. Technical Data Article number: M315.248 SKU: M315.248 GTIN: 4054469126722 eClass: 21170214 Customs tariff: 90173000 Facts Thread size: M48 × 5 Tolerance class: 6g (DIN 13) Orientation: Right‑hand Material: Hardened gauge steel Special features Type: No‑go (reject) ring for pass/fail checks Category: Gauges / Thread gauges Application: Verification of metric ISO regular threads FAQ What is the intended use of this ring gauge? The thread ring gauge M48 × 5 mm (no‑go), Metav IndustryLine, SKU M315.248, is intended for pass/fail inspection of M48 × 5 metric ISO threads in production and incoming inspection. Does the gauge conform to recognised standards? Yes, the ring gauge is manufactured to DIN 13 and marked for 6g tolerance class, providing a standardised reference for thread acceptance. Which material is used for the gauge and why does it matter? The ring is made from hardened gauge steel, chosen for its wear resistance and stability, which preserves the gauge geometry during repeated inspections. Can this tool be used for left‑hand threads? No; this specific ring is for right‑hand metric ISO threads only. Left‑hand checks require the corresponding left‑hand gauge. Is the ring suitable for production sampling? Yes, the no‑go ring is designed for rapid tactile verification and is well suited to production sampling or incoming goods checks where fast decisions are required. What does the no‑go function detect? The no‑go function identifies threads that exceed permissible limits in form or size; the M48 × 5 no‑go ring will not assemble on parts that are out of tolerance, providing a clear fail indicator. Metav IndustryLine: Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
M4x0.5 Thread Go Gauge, Right-Hand, Hardened Gauge Steel, DIN 13 6g - Metav IndustryLine
Combine clear conformity to DIN 13 with a hardened gauge steel construction for rapid, reproducible go/no‑go checks of fine metric threads; the M4 x 0.5 mm ring supports consistent inspection routines and reduces rework. Order the thread ring directly via Metav Werkzeuge or consult the specialists for batch supply and integration advice. Thread ring gauge M4 x 0.5 mm — gauging ring, tolerance 6g (Metav IndustryLine) The thread ring gauge M4 x 0.5 mm is intended for quick verification of metric ISO fine threads (right‑hand) in production and quality control environments. Hardened gauge steel construction DIN 13 compliant, tolerance class 6g For metric ISO fine thread M4 x 0.5 Reliable inspection to established standards A compact thread ring gauge that meets DIN 13 and the 6g tolerance class provides a clear, objective check of external threads. As a dedicated gauging tool it performs a simple go/no‑go function: the ring either enters the sampled thread (pass) or it does not (fail). This direct assessment reduces interpretation errors compared with visual checks and speeds up routine inspection cycles. The clear standard conformity also simplifies documentation for incoming inspection and process audits, helping to keep production throughput steady. Durable construction for consistent measurement performance Manufactured from hardened gauge steel, the ring is designed for long service life under frequent use. The hardened material resists wear at the measuring flank, preserving the intended thread form and ensuring repeatability across many cycles. Low mass and compact form factor ease handling at the workbench or inspection station, and the robust finish supports uncomplicated cleaning and storage. Together, these attributes reduce the need for frequent replacement and maintain reproducible results over time. Practical fit for shop‑floor quality control This gauging ring is suitable for rapid go/no‑go checks during assembly, final inspection or first‑article verification. Its specification for metric ISO fine threads makes it a practical choice for components requiring finer pitches, while the right‑hand orientation matches standard production threads. Supplied under the Metav IndustryLine label, the item is intended for reliable procurement and traceable sourcing to support consistent quality across production batches. The small footprint and decisive pass/fail outcome make the ring an efficient addition to standard inspection sets. For process‑stable thread testing and reliable batch supply, contact Metav Werkzeuge to discuss the Metav IndustryLine thread ring gauge M4 x 0.5 mm and arrange delivery from our Emmerich facility. Technical data Article number: M315.204.2 GTIN: 4054469125411 Material: gauge steel, hardened Size: M4 x 0.5 mm Standard: DIN 13, tolerance 6g Facts Weight: 0.01 kg Tariff number: 90173000 Category: Gauges / Inspection rings Brand: Metav IndustryLine Special features Right‑hand thread For metric ISO fine threads Go/no‑go gauging function Hardened construction for wear resistance FAQ What does the tolerance class 6g indicate for this ring gauge? The tolerance class 6g specifies the allowed dimensional and form limits for the mating external thread; the thread ring gauge M4 x 0.5 mm is made to that class so pass/fail checks correspond to the 6g acceptance band. Can this ring be used for fine‑pitch metric threads only? Yes, the ring is specified for metric ISO fine threads with a 0.5 mm pitch; it is intended for M4 x 0.5 external threads produced to the matching tolerance. What material is the gauge made from and how does that help? The gauge is manufactured from hardened gauge steel, which improves wear resistance and preserves the measuring flank form, supporting consistent results throughout repeated use of the M4 x 0.5 mm ring gauge. Is the M4 ring suitable for shop‑floor rapid checks? Yes, the compact form and decisive go/no‑go function make the M4 x 0.5 mm thread ring well suited to quick checks during assembly, sample inspection and incoming goods control. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
M4x0.7 Thread Go Gauge Right-Hand Metric ISO, Hardened Gauge Steel, DIN 13 6g - Metav IndustryLine
Take advantage of a fast, standards-based check with a hardened thread ring gauge that verifies M4 × 0.7 metric threads to DIN 13 tolerance 6g and saves inspection time on the shop floor. Order the gauge directly via Metav Werkzeuge or contact our consultants for application advice and batch supply. Thread ring gauge M4 × 0.7 — No‑go ring, DIN 13, 6g (Metav IndustryLine) The thread ring gauge M4 × 0.7 is a right‑hand, metric ISO no‑go ring designed for rapid reject verification in production and incoming inspection. No‑go ring for M4 × 0.7 threads Hardened gauge steel construction Conforms to DIN 13, tolerance 6g Right‑hand metric ISO thread Faster rejection decisions for production lines The primary purpose of this thread ring gauge is straightforward: provide a binary check that separates acceptable threads from rejects without time‑consuming measurements. As a No‑go ring for M4 × 0.7, it eliminates guesswork during rapid sample inspections and shortens throughput times in assembly or machining cells. The pass/no‑go principle is easy to apply at the workstation, which reduces operator training and minimises human error while keeping quality control efficient and predictable. Built to resist wear and maintain accuracy Manufactured from hardened gauge steel, the ring offers high wear resistance and dimensional stability under repeated use. The choice of material and the heat treatment make the gauge robust against the abrasion and handling typical in industrial environments, extending service life and reducing the need for frequent replacement. Conformance to DIN 13 and the specified 6g tolerance ensures the ring matches established thread geometry and provides a reliable reference for routine inspections. Practical fit into workshop quality routines The ring’s compact form and modest mass (approx. 0.1 kg) make it simple to store on a tool board or keep at the inspection bench for immediate use. Where traceable measurement chains are required, the ring is used as a go/no‑go control within established sampling plans and assembly checks. Its right‑hand metric ISO profile ensures compatibility with standard M4 × 0.7 threaded parts common across mechanical assemblies, fasteners and small components, supporting consistent quality in both incoming goods control and final assembly verification. Clear standards and straightforward interpretation By referencing DIN 13 and the 6g tolerance class, the gauge ties directly into normative thread specifications, allowing quality engineers to document compliance without complex calculations. The simple try‑fit method saves time compared with full metrological inspection and is particularly suitable where production speed and reproducibility matter most. For shops aiming to standardise checks across multiple workstations, a set of comparable ring gauges offers immediate, comparable results with little setup. Contact Metav Werkzeuge today for supply and advice on integrating the M4 × 0.7 no‑go ring into inspection workflows, or request assistance from our consultants for batch orders and storage solutions Technical Data Article number: M315.204 GTIN: 4054469125398 Mass / size: M4 × 0.7 Weight: 0.1 kg Facts Material: hardened gauge steel Standard: DIN 13 Tolerance class: 6g Thread direction: right‑hand Special features Function: No‑go (reject) ring gauge Category: thread inspection gauge Typical use: production and incoming inspection Packaging: standard industrial packaging FAQ What is the primary use of this ring gauge? The M4 × 0.7 thread ring gauge serves as a No‑go control to quickly identify rejected threads; the Metav IndustryLine M315.204 is intended for routine production and incoming inspection of metric ISO threads. Which standards does the gauge follow? This ring complies with DIN 13 and the 6g tolerance class, making it suitable for checking common metric ISO threads in mechanical assemblies. What material is the gauge made from and why does that matter? The gauge is manufactured from hardened gauge steel, which provides wear resistance and dimensional stability so the ring maintains accuracy through repeated checks. Can this gauge be used for left‑hand threads? No, this specific item is a right‑hand metric ISO ring for M4 × 0.7 threads; left‑hand variants must be specified separately. How should the gauge be integrated into inspection routines? Use the M315.204 as a quick go/no‑go control at the inspection bench or on the production line; record results in the quality log and include the ring as part of routine sampling plans. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
M4×0.35mm Limit Thread Plug Gauge Right-Hand Metric ISO 6H Hardened Gauge Steel, DIN 13 - Metav IndustryLine
Take advantage of the combination of hardened gauge steel, exact DIN 13, 6H tolerancing and a compact M4 x 0.35 form for reliable thread verification on fine-thread components; order via Metav Werkzeuge or consult our specialists for application advice. Grenzgewinde-Lehrdorn M4 x 0.35 — Metric ISO fine-thread limit plug gauge, right-hand A Grenzgewinde-Lehrdorn M4 x 0.35 serves as a compact, high-precision limit plug gauge for fast go/no-go checks on metric ISO fine threads in production and inspection environments Metric fine thread M4 x 0.35 Hardened gauge steel construction Manufactured to DIN 13, 6H Compact weight 0.03 kg Consistent thread verification for efficient production A limit plug gauge in this class provides immediate, unambiguous results for pass/fail checks. The combination of M4 x 0.35 geometry and DIN 13, 6H tolerancing means the gauge is suitable for standardised checks on fine-threaded components, reducing setup time at inspection points. By applying a simple go/no-go principle, the inspection workflow becomes more predictable, which supports higher throughput and fewer downstream reworks. Built for repeatability and practical workshop use Made from hardened gauge steel, the gauge resists wear while keeping its dimensional stability over many cycles. The robust material selection and compact mass ensure the tool can be handled easily on the shop floor and stored without special requirements. As a result, measurement repeatability is improved and the likelihood of measurement-induced error is reduced, which supports consistent quality control across production batches. Rapid decisions, lower scrap and simpler traceability The right-hand limit plug design allows rapid verification of assembly-ready threads and helps to prevent incorrect mating or rejected parts later in the process. Clear mechanical pass/fail assessment accelerates decision-making at the inspection station and cuts down on inspection times. The use of a standardised limit gauge also aids traceability in documentation and supports compliance with common workshop quality routines. Secure reliable thread checking with the Metav IndustryLine limit plug gauge — contact Metav Werkzeuge for availability and application guidance on this gauge at info@metav-werkzeuge.com or +49 2822 7131930 Technical data Article number: M315.004.1 GTIN: 4054469122069 Weight: 0.03 kg Core specifications Thread size: M4 x 0.35 Tolerance: 6H Standard: DIN 13 Tariff code: 90173000 Features Limit plug gauge, right-hand Material: hardened gauge steel Category: Lehren / Messstifte FAQ How is the gauge used for thread inspection? The limit plug gauge is used as a go/no-go tool to check whether a metric fine thread meets the tolerances specified by DIN 13 and the M4 x 0.35 geometry; the go condition confirms acceptability, the no-go indicates out-of-tolerance. Is this gauge suitable for fine-thread fasteners in assemblies? Yes, the M4 x 0.35 configuration and 6H tolerance are explicitly intended for metric ISO fine threads commonly found in small fasteners and precision assemblies. What material is the gauge made from and why does that matter? The gauge is manufactured from hardened gauge steel, chosen to resist wear and preserve dimensional accuracy over repeated inspections. Does the product support traceable documentation? The gauge is a standardised inspection tool used in documented quality routines; its article number and GTIN allow clear identification in procurement and inspection records. Which applications are typical for this type of gauge? Typical applications include production-line thread checks, incoming inspection of fasteners and sampling tests in toolrooms where quick, reliable thread verification is needed. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
M4×0.5 Thread Limit Gauge, Metric ISO Fine Pitch, Right-Hand, Hardened Gauge Steel, DIN 13 6H - Metav IndustryLine
Take advantage of precise, standards‑compliant thread verification combined with durable, hardened gauge steel for repeatable pass/fail checks. Order the gauge directly via Metav Werkzeuge or consult our specialists for integration into quality control workflows. Limit thread plug gauge M4 x 0.5 mm — metric ISO fine thread, right‑hand (Metav IndustryLine) A limit thread plug gauge M4 x 0.5 mm designed for quick, reliable verification of metric ISO fine threads in production and inspection processes Hardened gauge steel for long service life Conforms to DIN 13, tolerance class 6H Metric fine thread M4 × 0.5, right‑hand Ensure conformity with a simple, robust check The limit gauge provides a clear go/no‑go result for threaded parts, enabling immediate decisions on conformity. Calibrated geometry and production to DIN 13 ensure that the go dimension corresponds to the defined 6H tolerance band, reducing ambiguous measurements and downstream rework. Used as a go/no‑go control, the device shortens inspection time and supports consistent quality documentation in manufacturing environments. Durable construction that maintains accuracy Manufactured from hardened gauge steel, the gauge resists wear and maintains dimensional stability over repeated cycles. The hardened material minimises surface damage and abrasion, which preserves the defined thread form and pitch over prolonged use. Low mass and compact dimensions also aid handling during serial checks, while the robust finish supports frequent use in workshop and production settings. Ideal for fine‑thread components and compact assemblies The M4 × 0.5 mm size suits small fastenings commonly found in electronics, instrumentation and precision assemblies where fine threads are specified. Its right‑hand configuration matches standard metric parts and allows straightforward, repeatable insertion checks. The compact format simplifies storage on inspection benches and in tool sets, helping to keep process control close to the assembly line. Traceable data and workshop integration The gauge is supplied with clear identification (SKU M315.004.2, GTIN 4054469122076) to support traceability within quality systems. As a simple mechanical limit gauge, it integrates easily with existing inspection routines and audit trails; physical checks can be recorded alongside batch numbers to document conformity. Choosing a standards‑based gauge from a recognised series aids supplier consistency and procurement transparency. Contact Metav Werkzeuge for tailored advice on implementing this Metav IndustryLine limit gauge in production — Metav Werkzeuge in Emmerich can advise on stock availability and delivery to your workshop Technical Data Article number: M315.004.2 GTIN: 4054469122076 Tariff number: 90173000 eClass: 21170235 Facts Thread: M4 × 0.5 mm Weight: 0.01 kg Standard: DIN 13, 6H Special features Material: gauge steel, hardened Right‑hand metric ISO fine thread Category: limit thread plug gauge Intended use: go/no‑go verification in production and inspection FAQ What does the 6H tolerance indicate for this gauge? The 6H designation refers to the internal thread tolerance class defined by DIN standards; the Metav IndustryLine limit thread plug gauge M4 x 0.5 mm is manufactured to match this class, providing a reliable pass/no‑pass check for mating parts. Can this gauge be used in a production environment for frequent checks? Yes, the hardened gauge steel construction and compact form factor of the M315.004.2 make it suitable for repeated use on the production floor as a quick verification tool. Is the gauge suitable for measuring left‑hand threads? This specific item is a right‑hand metric plug gauge for M4 × 0.5 threads; left‑hand versions must be ordered separately to match the required thread direction. How should the gauge be stored to maximise service life? Store the gauge clean and dry in a protective holder or drawer to avoid corrosion and mechanical damage; the hardened steel resists wear, but careful handling preserves the calibrated form. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
M4×0.5 Thread Ring Gauge Go Metric ISO Fine Right-Handed DIN 13 6g Hardened Gauge Steel - Metav IndustryLine
Take advantage of a precision-tested combination of M4 x 0.5 nominal size, DIN 13 6g tolerance and hardened gauge steel for reliable Go checks in production. Order the ring directly via Metav Werkzeuge or consult our specialists for application advice. Thread ring gauge M4 x 0.5 — Go ring for metric ISO fine threads (Metav IndustryLine) The Thread ring gauge M4 x 0.5 is a right-hand Go gauge designed for quick pass/fail verification of metric ISO fine threads in production and inspection environments. Go ring for M4 x 0.5 metric fine thread Hardened gauge steel construction Conforms to DIN 13 tolerance class 6g Lightweight 0.02 kg for easy handling Fast, reproducible pass/fail checks on the shop floor A compact Go ring provides immediate confirmation that a threaded component meets the defined tolerance. The Go ring principle is straightforward: a correct thread must enter the gauge without forcing, which speeds up quality control and reduces machine downtime. With the nominal size M4 x 0.5 and the industrial DIN 13 6g tolerance class, this gauge is suitable for routine inspections of fine threads commonly found in small assemblies and precision components. The result is a clear, objective decision at the point of manufacture, supporting faster throughput and fewer uncertain measurements. Durable design that keeps measurement uncertainty low Manufactured from hardened gauge steel, the ring resists wear and maintains dimensional stability over many cycles, which translates into a longer service life and consistent verification results. The slim, lightweight construction (approx. 0.02 kg) makes the gauge easy to handle and store while remaining robust enough for daily use. Because the component is a Go-type gauge, it is optimised for repeatability: the hardened material and precise finish minimise changes in fit that could otherwise introduce measurement drift, helping to preserve inspection integrity across long production runs. Conformity and practical benefits for inspection workflows Compliance with DIN 13 and the 6g tolerance class ensures the gauge matches established thread standards, enabling straightforward integration into existing quality procedures and documentation. The ring is intended for right-hand metric ISO fine threads and serves as a simple, low-effort control instrument where a full-profile inspection is unnecessary or impractical. Used alongside calibrated reference tools, a Go ring like this one reduces processing time for routine checks and supports traceable, standards-based quality management in workshops and industrial environments. For dependable thread inspection tailored to production needs, request the Metav IndustryLine M4 x 0.5 Go ring from Metav Werkzeuge or contact our specialists at info@metav-werkzeuge.com / +49 2822 7131930 to confirm suitability for specific applications Technical Data Article number: M315.104.2 GTIN: 4054469123745 Weight: 0.02 kg Nominal size: M4 x 0.5 SKU: M315.104.2 Core specifications Thread pitch: 0.5 mm Nominal diameter: 4 mm Tolerance class: 6g (DIN 13) Type: Go ring Special features Material: hardened gauge steel Right-hand thread gauge Intended for metric ISO fine threads Category: Ring gauge / Go gauge FAQ What is the purpose of this ring gauge? The ring is a Go gauge for fast pass/fail verification of metric ISO fine threads; the Metav IndustryLine M4 x 0.5 ring confirms whether a right-hand M4 x 0.5 thread meets the DIN 13, 6g requirement. Can this gauge be used for production sampling? Yes. The hardened construction and DIN 13 conformity make the ring suitable for routine production sampling and quick in-process checks. What does the 6g specification mean? The 6g designation denotes the thread tolerance class under DIN 13; it defines the permissible limits for the mating external thread that the Go gauge is intended to accept. Is the material suitable for long-term use? Hardened gauge steel provides wear resistance and dimensional stability, supporting a long service life under regular inspection cycles. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
M4×0.7 Limit Thread Go Gauge Right-Hand, Hardened Gauge Steel, DIN 13 6H - Metav IndustryLine
Benefit from the combination of hardened gauge steel, DIN 13 6H conformity and a compact M4 x 0.7 mm format for fast, reproducible thread checks on the shop floor; order the limit gauge directly via Metav Werkzeuge or consult the team for further specification support. Limit thread plug gauge M4 x 0.7 mm — right-hand, DIN 13 6H (Metav IndustryLine) Limit thread plug gauge M4 x 0.7 mm is a precision checking tool for verifying metric ISO right-hand internal threads in production and quality inspection environments. Hardened gauge steel construction Conforms to DIN 13, tolerance 6H Right-hand M4 x 0.7 mm limit gauge Lightweight 0.02 kg for easy handling Faster pass/fail control reduces downtime A compact limit gauge delivers immediate, unambiguous pass/fail results for internal threads, which speeds up inspection cycles and lowers throughput time. The M4 x 0.7 mm right-hand dimension is matched to ISO metric thread standards, while the hardened gauge steel body resists wear during repeated engagement. Conformity with DIN 13 and the 6H tolerance class provides a clear, standards-based reference that supports consistent production decisions and reduces the risk of scrap. Small, robust design for everyday workshop use The slim form and 0.02 kg mass make this plug gauge easy to handle at bench or machine‑side, improving ergonomics during repetitive checks. The robust hardening process ensures a stable measuring edge and long service life, which translates into lower replacement frequency and predictable maintenance intervals. As a limit gauge, the component is optimised for repeatable tactile checking rather than dimensional measurement, giving quick reliability when integrated in routine quality workflows. Seamless integration into inspection routines This limit thread plug gauge is intended for straightforward inclusion in inspection kits and gauging stations. Clear identification via SKU and GTIN facilitates traceability within stock systems and quality records, while the tool’s construction supports frequent use in production environments. For specification matching, Metav IndustryLine items are backed by a distribution and advisory network that helps align the right gauge to the application and the preferred inspection procedure. Contact Metav Werkzeuge (info@metav-werkzeuge.com, +49 2822 7131930) for purchasing advice and rapid dispatch of Metav IndustryLine gauges Technical data SKU: M315.004 GTIN: 4054469122052 Tariff code: 90173000 Weight: 0.02 kg Brand: Metav IndustryLine Facts Thread size: M4 x 0.7 Direction: Right-hand Standard / tolerance: DIN 13, 6H Category code: 21170235 Special features Material: gauge steel, hardened Product type: Limit thread plug gauge Intended use: Metric ISO internal thread verification Categories: Gauges, Gauge pins FAQ What does this gauge check? The limit thread plug gauge checks acceptance of metric ISO internal threads; the M4 x 0.7 mm Metav IndustryLine plug verifies right-hand threads against DIN 13, tolerance 6H. Is this gauge suitable for production use? Yes; the hardened gauge steel and DIN 13 conformity make the plug gauge appropriate for routine shop‑floor inspections and repetitive pass/fail checks. How should the gauge be stored to preserve accuracy? Store the plug gauge dry and protected from impact; a foam-lined case or dedicated compartment reduces wear on the measuring faces and preserves the tool’s functional life. Can this gauge be referenced in quality documentation? The M315.004 SKU and GTIN enable traceability in inventory and quality records; include these identifiers when logging inspection tools in system documentation. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
M5 x 0.35mm Thread Go Ring Gauge Metric ISO Fine Right-Handed DIN 13, Hardened Gauge Steel - Metav IndustryLine
Combine the hardened gauge steel construction with conformity to DIN 13 (6g) for dependable pass/fail inspection of metric fine threads; this compact ring gauge supports consistent production quality. Order the M5 x 0.35 thread ring gauge directly via Metav Werkzeuge or ask the consultants for application advice. M5 x 0.35 thread ring gauge (DIN 13, 6g) – Metav IndustryLine The M5 x 0.35 thread ring gauge is a hardened inspection gauge for metric ISO fine threads (right-hand), designed for routine quality checks in production and laboratory environments. Hardened gauge steel construction Conforms to DIN 13, tolerance 6g For metric ISO fine threads, right-hand Lightweight 0.01 kg for easy handling Precise conformity checks to speed inspection A limit ring gauge provides an immediate go/no-go decision: conformity is assessed against the DIN 13 profile and the specified 6g tolerance. This makes the tool especially useful where throughput and repeatability matter, such as batch production or first-article inspection. The gauge removes ambiguity from visual checks and comparative measurements, so inspection cycles become faster and statistical process control gains reliable, repeatable inputs. Robust build for repetitive use on the shop floor Manufactured from hardened gauge steel, the gauge resists wear and maintains its profile under frequent handling, which reduces rework and downtime. The compact, lightweight form factor (0.01 kg) suits handheld inspection and quick part sampling at the machine, while the right-hand metric ISO fine thread geometry ensures direct compatibility with M5 × 0.35 components. These attributes combine to lower the total cost of control by extending service intervals and simplifying handling during quality routines. Simple integration into quality workflows As a dedicated inspection instrument from Metav IndustryLine, the ring gauge is straightforward to include in existing quality procedures: mark sample points, apply the gauge for a pass/fail assessment and record results in the QC log. Its clear conformity criteria facilitate operator training and reduce interpretation errors. For mixed production runs or external suppliers, this gauge provides an unambiguous acceptance criterion that supports consistent supplier control and traceable quality documentation. For reliable thread inspection choose the Metav IndustryLine M5 x 0.35 ring gauge — contact Metav Werkzeuge in Emmerich for supply and application guidance. Technical data Article number: M315.205.1 SKU: M315.205.1 GTIN: 4054469125435 Manufacturer: Metav IndustryLine Facts Nominal diameter: 5 mm Pitch: 0.35 mm Weight: 0.01 kg Tolerance class: 6g Standard: DIN 13 Special features Material: hardened gauge steel Right-hand thread For metric ISO fine threads Category: Gauges / Lehren FAQ What tolerance class does this gauge check? The gauge verifies thread conformity to the 6g tolerance class specified under DIN 13; the M5 x 0.35 thread ring gauge is manufactured to that tolerance for clear go/no-go assessment. Is this gauge suitable for metric ISO fine threads? Yes — the M5 x 0.35 thread ring gauge is intended specifically for metric ISO fine threads with a 0.35 mm pitch and right-hand orientation. What material is the gauge made from? The ring gauge is made from hardened gauge steel, which is selected for wear resistance and dimensional stability in routine inspection. How is the gauge typically used in production? The gauge is applied as a limit check: a part either fits the ring (pass) or does not (fail). The M5 x 0.35 thread ring gauge is suited for quick in-process checks and sampling during final inspection. What is the article number for ordering or referencing? The article number is M315.205.1 and the SKU is M315.205.1 for the Metav IndustryLine M5 x 0.35 thread ring gauge. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
Fast, tactile checks where electronics are impractical
Gauges and test pins provide unequivocal go/no-go results for threads, bores, gaps and radii without relying on electronics. The range covers plug gauges and ring gauges for internal and external threads, feeler gauges and precision feeler strips for micro‑gap assessment, plus probe pins and measuring pins for tactile diameter and pitch checks.
How these tools work in the production environment
Mechanical gauges operate as direct reference standards: a plug gauge or ring gauge verifies conformity to thread profiles and mating ability, while limit gauges separate accept from reject in a single step. Test pins are used to tactilely measure small bore diameters, centre‑to‑centre distances and radii. Manufactured from hardened gauge steel or ceramic and often precision lapped, these instruments deliver immediate physical results that are ideal for incoming inspection, machine‑side checks and final control.
Measurable benefits that affect production performance
- Reduced scrap and rework through rapid, unambiguous pass/fail assessment.
- Increased repeatability thanks to very low measurement uncertainty and fine lapping.
- Lower downtime: quick checks at the machine save cycle time and reduce setup periods.
- Durable construction with high wear resistance from specialised, low‑distortion alloys.
- Versatile delivery formats: individual gauges, organised sets in wooden cases or metre‑length feeler rolls compliant with DIN 2269.
Why Metav is the practical choice for precision supplies
Metav combines decades of expertise with a broad warehouse and quality filtering from Emmerich. As a precision partner for industry, craft and trade, Metav supplies a comprehensive selection of gauges and test pins alongside complementary tools such as precision calipers and setting rings. With over 48,000 customers and a catalogue exceeding 250,000 items, Metav is positioned to supply reliably, reduce vendor complexity and support traceable quality control to national standards.
Summary
Gauges and test pins are indispensable for dependable, repeatable quality assurance where tactile, mechanical verification is preferred. Choose these plug gauges, ring gauges, feeler strips and probe pins when immediate, robust measurement decisions are required on the shop floor.
FAQ
What materials are gauges and test pins typically made from?
Gauges and test pins are usually manufactured from hardened gauge steel for durability and wear resistance; ceramic variants are available where thermal stability and minimal wear are critical.
How do thread gauges ensure mating capability?
Thread plug gauges and ring gauges check flank diameters and thread form against standards, providing a clear go/no‑go verdict that confirms pairability with mating parts.
Which tolerance class should I choose for probe pins and gauge sets?
Select tolerance classes aligned with your inspection requirements; for high‑precision tasks, sets produced to DIN 2269 or equivalent tolerance classes ensure micrometre‑level control and repeatability.
Can feeler gauges measure contact gaps in valve and engine work reliably?
Yes. Feeler gauges and precision feeler strips, supplied either as a fan or metre‑length rolls, allow accurate assessment of valve clearances and contact gaps down to micrometre increments.
How do limit gauges speed up in‑process inspection?
Limit gauges separate good from bad in a single, tactile operation, enabling rapid go/no‑go checks at the machine and reducing both inspection time and the likelihood of human interpretation errors.
Fragen zu diesen Produkten??
Mit mehr als 30 Jahren Erfahrung beraten wir Sie gerne persönlich.
Tel.: +49 2822 7131930
Mail: info@metav-werkzeuge.com