Precision gauge blocks and plug gauges for reliable dimensional control
Mechanical gauge blocks and plug gauges are essential for tactile verification of threads, bores and gap dimensions, providing fast, unambiguous go/no-go results that enhance process reliability and reduce scrap. Designed for industrial metalworking and toolmaking, these precision tools support incoming inspection and final quality checks by delivering traceable measurements in applications such as thread inspection, bore diameter testing and spacing checks. Manufactured from specially hardened, low-distortion alloys and fine-lapped for minimal measurement uncertainty, the range includes thread plug gauges, precision plug gauges and calibration gauge blocks to ensure long-term repeatability and wear resistance.
M52x5 Limit Thread Plug Gauge ISO Metric Right-Hand, Hardened Gauge Steel, DIN 13 6H - Metav IndustryLine
Take advantage of the combination of hardened gauge-steel construction, clear conformity to DIN 13 (6H) and the space-saving M52 × 5 sizing for fast, repeatable thread verification on the shop floor. Order the limit thread plug gauge M52 × 5 directly via Metav Werkzeuge or ask our consultants if needed. Limit thread plug gauge M52 × 5 (right-hand) — hardened gauge steel, DIN 13 (6H) — Metav IndustryLine A limit thread plug gauge M52 × 5 for rapid verification of metric ISO standard threads in production and inspection environments Hardened gauge-steel construction For M52 × 5 metric ISO threads Conforms to DIN 13, tolerance 6H Right-hand go/no-go thread checking Ensure production quality with fast, objective thread checks A compact go/no-go plug gauge provides an immediate, objective verdict on threaded parts, removing subjective judgement from routine checks. Manufactured in hardened gauge steel, the device resists wear and maintains the thread form that defines accept/reject limits. Used at the point of manufacture or at final inspection, the small size and robust construction reduce downtime: faulty components are detected before assembly, avoiding costly rework and improving overall process efficiency. Built for repeatability and long service life The gauge is engineered to preserve dimensional stability under shop-floor conditions. Conformity with DIN 13 (6H) ensures the defined tolerance boundary is applied consistently; the result is reproducible inspection across shifts and operators. The right-hand configuration and clear go/no-go distinction simplify training and standard operating procedures, so measurement variance caused by handling is minimised. The stable design supports frequent checks without rapid degradation of the acceptance limits. Practical application and inspection guidance Designed for metric ISO standard threads of size M52 × 5, this limit plug gauge is suitable where fast verification of internal thread geometry is required. The gauge serves as a go/no-go reference for thread form, pitch and basic size according to the standard; a plain visual or tactile check is enough to confirm compliance. For traceability in quality documentation, the solid construction and unambiguous pass/fail result streamline process control and reduce the need for time-consuming measuring devices for routine checks. Choose Metav IndustryLine for dependable thread gauges stocked in Emmerich; contact Metav Werkzeuge to confirm technical fit and availability at info@metav-werkzeuge.com or by phone on +49 2822 7131930 Technical data Article number: M315.052 GTIN: 4054469123479 Manufacturer: Metav IndustryLine Material: Hardened gauge steel Standard: DIN 13, 6H Facts Size: M52 × 5 Weight: 1.3 kg Tariff number: 90173000 Special features Right-hand go/no-go plug gauge For metric ISO standard threads Durable, wear-resistant construction Category: Gauges FAQ What is the primary use of this plug gauge? The limit thread plug gauge M52 × 5 is used for pass/fail verification of internal metric ISO threads; it gives an immediate go/no-go result for quick shop-floor inspection. Which standard does the gauge follow? The tool is manufactured to the requirements of DIN 13 with the tolerance class 6H for metric ISO threads, ensuring consistent acceptance limits. How does the go/no-go function help in production? A clear go/no-go configuration simplifies routine checks, reduces measurement time and prevents incorrect assemblies by providing an unequivocal acceptance decision. What are the handling considerations for longevity? Store the gauge clean and dry, avoid impacts and use light lubricant if required; the hardened gauge-steel construction supports repeated use while maintaining dimensional stability. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
M52x5 Thread Gauge Ring Go, DIN 13 6g, Hardened Gauge Steel, Right-Hand - Metav IndustryLine
Take advantage of a precision-tested combination of M52 x 5 nominal size, DIN 13 / 6g tolerance and hardened gauge steel for reliable thread acceptance checks; order via Metav Werkzeuge or consult our specialists for application advice. Thread ring gauge M52 x 5 mm 'go' — Thread ring gauge, DIN 13 6g, Metav IndustryLine The Thread ring gauge M52 x 5 mm 'go' is a right-hand, go-type gauge for verifying metric ISO threads in production and quality assurance environments. M52 x 5 metric ISO thread, right-hand, go Hardened gauge steel for long service life Conforms to DIN 13; tolerance 6g Consistent conformity and faster inspection cycles The primary benefit of this ring gauge is a repeatable inspection result that speeds up in-line quality control. Designed to the DIN 13 specification with tolerance class 6g, the tool gives a clear go/no-go decision for M52 × 5 metric ISO threads, removing ambiguity from pass/fail checks. Where traceable, rapid verification is needed, a dedicated go gauge reduces setup time and prevents rework by confirming dimensional compliance instantly, supporting higher throughput on production lines. Robust construction for long service life Manufactured from hardened gauge steel, the gauge withstands frequent use without premature wear, ensuring stable dimensional integrity over time. The material choice and heat treatment deliver improved resistance to abrasion and deformation, which benefits long production runs and repeated field checks. The solid construction also eases handling and gives a substantial tactile feel during inspection, aiding reliable seating on mating threads and reducing the risk of false readings caused by damaged or worn gauges. Practical use in workshop and inspection routines This right-hand ring gauge is intended for straightforward acceptance testing of ISO metric external threads. Typical applications include first-article inspection, batch sampling and in-process checks in machining, assembly and maintenance shops. As a purpose-built verification tool, it integrates easily into standard inspection jigs or handheld workflows and complements other metrology equipment for a complete quality-assurance routine. The clear go-only function is particularly useful where the aim is rapid confirmation of conformity rather than exhaustive dimensional analysis. Contact Metav Werkzeuge for purchase details and technical consultation on the Metav IndustryLine range via info@metav-werkzeuge.com or call +49 2822 7131930 to ensure the gauge matches the production requirements Technical data SKU: M315.152 GTIN: 4054469125145 Size: M52 x 5 mm Type: Thread ring gauge, go (acceptance), right-hand Material: Gauge steel, hardened Standard: DIN 13, 6g Weight: 2.1 kg Tariff number: 90173000 Key figures Nominal thread: M52 Pitch: 5 mm Tolerance class: 6g Weight: 2.1 kg Features and applications For metric ISO external threads Right-hand, go (acceptance) verification Suited to production and quality control Hardened material for extended service life FAQ What thread form and size does this gauge check? The ring checks metric ISO external threads with a nominal size of M52 × 5 mm using the go-type acceptance criterion. Which standard and tolerance class apply to this gauge? The tool conforms to DIN 13 and is manufactured to tolerance class 6g, suitable for standard ISO thread acceptance testing. What material is the gauge made from and why is that important? The gauge is made from hardened gauge steel, providing abrasion resistance and dimensional stability for repeated use in inspection routines. Is this gauge suitable for workshop use or only for laboratory inspection? This ring gauge is designed for both workshop and routine inspection; its robustness and go-only function make it practical for in-process checks as well as shop-floor quality control. Which manufacturer and SKU identify this product? This item is part of the Metav IndustryLine and is listed under SKU M315.152 for identification in procurement and inventory systems. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
M52x5 Thread Go Ring Right-Hand ISO Metric Thread DIN 13, 6g Hardened Gauge Steel 2.1 kg - Metav IndustryLine
Take advantage of a hardened gauge-steel construction and strict conformity to DIN 13 (6g) for reliable thread inspections; the M52 x 5 mm size ensures direct compatibility with standard metric ISO external threads. Order the gauge directly via Metav Werkzeuge or consult our specialists for application advice. Thread Gauge Ring M52 x 5 mm — hardened gauge steel, DIN 13 (6g), right‑hand Thread Gauge Ring M52 x 5 mm for quick verification of metric ISO external threads in production and workshop inspection environments Hardened gauge steel construction Conforms to DIN 13, tolerance 6g M52 x 5 mm metric ISO thread, right‑hand Robust for fast workshop checks Precision compliance that reduces rework and downtime The ring gauge is manufactured from hardened gauge steel, offering high wear resistance and stable dimensional behaviour under frequent use. Built to the DIN 13 standard with tolerance class 6g, this gauge provides an objective, repeatable reference for assessing external metric ISO threads. Using a standardised acceptance limit reduces subjective judgements on the shop floor and lowers the risk of producing parts outside specification, which in turn minimises costly rework and production stoppages. Fast, repeatable thread control for quality assurance Designed for straightforward in‑process checks, the ring enables rapid pass/fail assessment of external threads sized M52 x 5 mm (right‑hand). The compact geometry and robust material make it suitable for repeated engagement without quick deterioration, preserving measurement integrity across many cycles. Where documented inspection is required, the gauge supports efficient sampling routines and can be integrated into existing quality control protocols to speed up throughput while maintaining traceable conformity to the ISO metric thread system. Durable workshop tool with industrial traceability As a workshop and production aid, the ring gauge combines mechanical simplicity with industrial-grade reliability. The combination of standard conformity (DIN 13, 6g) and hardened construction means long service life and consistent results—attributes that contribute to predictable production planning. For procurement and stock management, the item is listed under article number M315.252 and is suitable for routine inspection tasks in metalworking and assembly operations where metric ISO threads must be verified. For dependable thread verification choose the Metav IndustryLine ring gauge — contact Metav Werkzeuge for tailored advice and local supply from Emmerich: info@metav-werkzeuge.com / +49 2822 7131930 Technical data Article number: M315.252 GTIN: 4054469126807 ECLASS: 21170214 Tariff number: 90173000 Core data Thread size: M52 x 5 mm Tolerance class: 6g Thread direction: right‑hand Standard: DIN 13 Special features Material: hardened gauge steel Application: verification of metric ISO external threads Category: ring gauge for workshop and production inspection FAQ What does the DIN 13 (6g) marking mean for thread checks? DIN 13 with tolerance class 6g defines the dimensional and tolerance framework for ISO metric threads; the Thread Gauge Ring M52 x 5 mm is manufactured to these limits to verify whether external threads meet that specification. Can this ring gauge be used on coated or plated parts? Coatings can alter effective thread dimensions; the M52 x 5 mm ring gauge checks the finished external profile — allow for coating thickness in the inspection plan when using this gauge. Is the ring suitable for high‑volume production inspection? Yes. The hardened gauge‑steel construction of the Metav IndustryLine ring gauge is designed for repetitive use and delivers consistent go/no‑go style verification in high‑throughput environments. How should the ring gauge be stored to preserve accuracy? Store the ring in a clean, dry environment and protect it from impacts and heavy contamination; regular visual checks and periodic calibration are recommended to ensure sustained accuracy. Does the product include traceability information? The ring gauge is supplied with clear identification via article number M315.252 and GTIN for traceability in inspection and inventory systems. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
M52×1 mm Limit Thread Go Gauge, Metric ISO Fine Thread Right-Hand, Hardened Gauge Steel, DIN 13 6H - Metav IndustryLine
Take advantage of the combination of hardened gauge steel, a precise DIN 13, 6H tolerance and the compact M52 x 1 mm size for dependable thread inspection in production and incoming‑goods control; order the M52 x 1 go/no-go thread plug gauge directly via Metav Werkzeuge or ask our consultants if needed. M52 x 1 mm Go/No-go Thread Plug Gauge — Limit gauge for metric ISO fine threads, right-hand, DIN 13 6H (Metav IndustryLine) The M52 x 1 mm go/no-go thread plug gauge is a hardened limit gauge intended for fast, repeatable inspection of right‑hand metric ISO fine threads in workshop and production environments Hardened gauge steel construction DIN 13 tolerance class 6H Go/no-go limit inspection Compact M52 x 1 mm format Accurate checks that keep production moving A limit thread plug gauge of this calibre enables quick go/no-go checks at the machine, inspection bench or assembly line, reducing interruption to the production flow. The instrument is specified for M52 x 1 mm metric ISO fine threads and manufactured to DIN 13, tolerance 6H, providing an objective pass/fail decision without additional measurement steps. Constructed from hardened gauge steel, the gauge resists wear during repeated use, which supports consistent results and lower long‑term inspection costs. In practice, a go/no-go limit gauge shortens cycle time for routine thread verification while preserving process reliability. Robust measurement principle and material benefits The go/no-go principle relies on two mating ends: a “go” end that must enter a correct thread and a “no‑go” end that must not. This simple, binary check eliminates subjective interpretation and accelerates throughput in quality control. The body material is hardened gauge steel, chosen for dimensional stability and abrasion resistance; that combination minimises the need for frequent replacement and preserves gauge integrity under industrial handling. The design balances rigidity and handling ease, with the unit weight of approximately 1.3 kg giving a reassuring feel during manual inspection. Designed for workshop realities and inspection integration This limit gauge is appropriate for incoming‑goods checks, in‑process control and final inspection of threaded components such as sleeves, housings and fasteners where an M52 x 1 fine thread is specified. Its right‑hand configuration and compliance with DIN 13, 6H make it suitable for standardised manufacturing protocols and documentation. For operations that integrate manual and semi‑automated inspection steps, the gauge provides a rapid verification stage that complements more detailed metrology equipment, enabling efficient sorting and immediate disposition of parts. Contact Metav Werkzeuge to discuss integrating the Metav IndustryLine M52 x 1 go/no-go thread plug gauge into the inspection routine or to request further technical information; call +49 2822 7131930 or email info@metav-werkzeuge.com Technical data SKU: M315.052.4 GTIN: 4054469123486 Weight: 1.3 kg Material: gauge steel, hardened Standard: DIN 13, 6H Thread: M52 x 1 mm, metric ISO fine thread, right‑hand Facts eClass: 21170235 Tariff number: 90173000 Category: Limit gauge / thread plug gauge Packaging: standard industrial packing Special features Go/no-go limit inspection Hardened construction for wear resistance Right‑hand metric ISO fine thread verification Suitable for workshop and production use FAQ What thread types does this gauge verify? The limit gauge verifies right‑hand metric ISO fine threads in size M52 x 1 mm and is manufactured to DIN 13 tolerance class 6H, suitable for standardised thread checks. How is the pass/fail decision made with this gauge? A binary check is used: the go end must engage correctly while the no‑go end must not enter; this quick method is provided by the Metav IndustryLine go/no-go thread plug gauge to enable immediate inspection results. Is the gauge suitable for production‑line use? Yes, the rugged hardened gauge steel construction and the straightforward go/no-go principle make the gauge well suited for repeated checks in production, incoming‑goods inspection and assembly processes. Does the product require special handling or storage? Normal industrial handling and dry storage are sufficient; keep the gauge clean and protected from corrosive environments to maintain dimensional integrity of the Metav IndustryLine limit gauge. What documentation accompanies the gauge? The gauge is supplied with its identification data; further traceability or calibration documentation can be discussed with Metav Werkzeuge for specific quality‑management needs. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
M52×1 mm Thread Ring Gauge, Right-Hand, Go, Hardened Gauge Steel, DIN 13 6g - Metav IndustryLine
Hardened gauge steel construction, DIN 13 tolerance class 6g and precise M52 x 1 thread geometry ensure reliable Go/No‑Go verification and consistent dimensional control on the shop floor. Take advantage of the combination of robustness, normative conformity and easy traceability for uninterrupted inspection routines. Order the gauge directly via Metav Werkzeuge or consult the specialists for application advice. Thread ring gauge M52 x 1 mm (Go) — DIN 13, 6g | Metav IndustryLine The Thread ring gauge M52 x 1 mm (Go) is a hardened Go ring for rapid verification of metric ISO fine threads in manufacturing and quality inspection. Hardened gauge steel construction DIN 13 tolerance class 6g For M52 x 1 metric ISO fine thread Right-hand Go ring for quick inspection Consistent Go/No‑Go inspection for production control The Thread ring gauge M52 x 1 mm (Go) is engineered for repeatable Go checks that reduce cycle time in assembly and incoming inspection. Manufactured to DIN 13 with tolerance class 6g, the ring provides a clear Go condition for metric ISO fine threads, enabling immediate pass/fail decisions at the machine or inspection bench. Using a dedicated ring gauge for the Go check removes subjective judgement from thread acceptance and supports standardised quality procedures. Designed for workshop durability and repeatable results Constructed from hardened gauge steel, the ring resists wear and preserves the thread form across many inspection cycles, which maintains repeatability and reduces rework. The solid build and balanced mass (approx. 2.1 kg) give stable handling during manual checks and help avoid false readings caused by distortion. The compact, single‑piece design minimises maintenance: no moving parts that require adjustment, just a robust gauge for routine verification. Integration into inspection routines and traceability The ring gauge fits into documented quality systems and is suitable for inline or stand‑alone checks in production. Identification via SKU M315.152.4 and GTIN 4054469125152 simplifies recording of inspection results and inventory tracking. Conformance to recognised thread standards supports auditability and helps to demonstrate compliance when sampling metric ISO fine threads in supplier control or final inspection. Contact Metav Werkzeuge for specification confirmation, availability and tailored advice on integrating the Metav IndustryLine M52 Go ring gauge into existing quality processes Technical Data Article number: M315.152.4 GTIN: 4054469125152 Label: Gewinde-Lehrring M52 x 1 mm gut DIN 13, f. metr. ISO-Feingewinde, rechts Manufacturer: Metav IndustryLine Facts Thread size: M52 x 1 Tolerance class: DIN 13, 6g Weight: 2.1 kg Tariff number: 90173000 Special features Material: gauge steel, hardened Right-hand Go ring for metric ISO fine threads Category: Lehren; Messstifte FAQ What does the 'Go' designation mean for this ring gauge? The Go designation indicates the ring is a Go gauge intended to verify that an external thread fits within the maximum material condition; the Metav IndustryLine M52 Go ring confirms that an M52 x 1 external thread meets the acceptance limit. Which standard does this thread gauge conform to? The gauge is manufactured to DIN 13 with tolerance class 6g, matching the requirements for metric ISO fine threads in routine inspection and production control. Is the gauge suitable for use in production sampling? Yes, the hardened construction and defined tolerance of the ring make it suitable for rapid Go checks in production sampling and incoming inspection where objective pass/fail decisions are required. How is the gauge identified for documentation? Identification is provided via SKU M315.152.4 and GTIN 4054469125152, which simplifies traceability in quality records for the Metav IndustryLine M52 Go ring gauge. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
M55 x 1 mm Gauge Ring Thread Ring, Metric ISO Fine Thread Right-Hand, Hardened Gauge Steel DIN 13, 6g - Metav IndustryLine
Take advantage of a robust inspection tool that combines DIN 13 conformity, hardened gauge‑steel construction and clear metric sizing to keep assembly and incoming inspection reliable. Order this gauge directly via Metav Werkzeuge or consult our specialists for application advice. Thread ring gauge M55 x 1 mm – right‑hand metric ISO fine thread (DIN 13, 6g) A Thread ring gauge M55 x 1 mm for quick verification of right‑hand metric ISO fine threads in production and incoming inspection. Hardened gauge steel for stable measurements Conforms to DIN 13 with tolerance 6g For right‑hand metric ISO fine thread M55×1 Ensure thread conformity with repeatable checks A thread ring gauge is the simplest and most direct way to verify that a threaded part meets specification. The M55 x 1 mm gauge is manufactured for inspection of right‑hand metric ISO fine threads and is produced to DIN 13 with 6g tolerance. Using a dedicated inspection ring reduces uncertainty compared with visual checks or trial assembly: a clear pass/fail indication accelerates quality decisions and prevents non‑conforming components from entering the production flow. This straightforward approach supports lean quality routines and helps maintain assembly reliability. Durable construction for everyday workshop use Made from hardened gauge steel, the gauge is designed for repetitive use on the shop floor. The robust material and heat treatment keep the working surfaces resistant to wear and deformation, which preserves the gauge geometry and extends service life. With a solid mass of 1.4 kg the tool offers good contact stability during verification, reducing the risk of misreads from wobble or poor seating. The result is fewer rechecks, consistent inspection outcomes and a lower lifetime cost of ownership compared with fragile or unprotected fittings. Integrates into established inspection procedures The ring gauge supports efficient process control in routine inspections or sampling plans. Its clear metric designation and standard compliance simplify documentation and traceability when used alongside measurement logs and production records. Where fast go/no‑go decisions are required, the ring gauge removes ambiguity and speeds throughput. Combined with Metav’s supply reliability and warehouse quality checks in Emmerich, the gauge is intended to be a dependable component of a well‑organised quality system. Contact Metav Werkzeuge for specification matching and reliable supply from Emmerich — request technical advice or an order recommendation from our consultants. Technical data Article number: M315.255.4 GTIN: 4054469126852 Customs tariff number: 90173000 Facts Thread size: M55 x 1 mm Tolerance: 6g Standard: DIN 13 Weight: 1.4 kg Special features Material: hardened gauge steel Right‑hand metric ISO fine thread Intended for inspection and go/no‑go checking FAQ What does the Thread ring gauge M55 x 1 mm check? The Thread ring gauge M55 x 1 mm checks right‑hand metric ISO fine threads against DIN 13 with a tolerance of 6g, providing a clear go/no‑go result for conformity. Is the gauge suitable for production sampling? Yes, the M55 x 1 mm gauge is designed for routine sampling and fast verification in production and incoming inspection. What material is the gauge made from and why does it matter? The gauge is manufactured from hardened gauge steel; this material choice preserves thread geometry under repeated use and improves long‑term stability of inspection results. Can this gauge be used for non‑standard or custom thread forms? The M55 x 1 mm ring is intended for standard metric ISO fine threads; non‑standard or custom thread profiles require specially manufactured gauges. Which SKU identifies this item for ordering? The item is listed as M315.255.4 and sold under the Metav IndustryLine range for easy procurement and stock control. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
M55x1 Go/No-Go Thread Plug Gauge Metric ISO Fine Thread Right-Hand, Hardened Gauge Steel, DIN 13 6H - Metav IndustryLine
Take advantage of hardened gauge steel construction and DIN 13, 6H conformity for reproducible thread inspection; the M55 x 1 right‑hand limit thread plug gauge provides fast go/no‑go control and stable handling on the shop floor. Order the limit thread plug gauge directly via Metav Werkzeuge or ask our consultants if needed. Limit thread plug gauge M55 x 1 — Metric ISO fine‑thread, DIN 13 6H (right‑hand), Metav IndustryLine A limit thread plug gauge M55 x 1 designed for go/no‑go verification of metric ISO fine threads in production and inspection environments, suitable for workshop and incoming‑inspection use. Hardened gauge steel construction Conforms to DIN 13, tolerance 6H Metric M55 x 1 fine thread, right‑hand Stable 1.5 kg mass for steady handling Consistent thread control for efficient production The limit thread plug gauge is engineered to deliver rapid pass/fail decisions during assembly and quality control. Built from hardened gauge steel, the tool resists wear and maintains form even under frequent use, which reduces rework and downtime. Conformity with DIN 13, 6H ensures the gauge checks the standard tolerance class for metric threads, enabling straightforward evaluation of thread profiles on components and fittings. This translates into measurable efficiency gains in repetitive inspection tasks and smoother throughput on production lines. Practical handling and inspection benefits Weighing 1.5 kg, the gauge offers a balanced feel that helps stabilise the operator’s action during insertion and withdrawal, minimising measurement variability. The M55 x 1 fine‑thread geometry and right‑hand orientation match common industrial applications for medium‑large threaded fittings, allowing quick compatibility checks without auxiliary instruments. The go/no‑go philosophy embedded in the design provides unequivocal results: an acceptance fit for the “go” end and a refusal on the “no‑go” end, which simplifies decision making for shop floor personnel and reduces dependence on subjective judgement. Where this gauge adds quality assurance value This thread plug gauge is suited to incoming inspection, final assembly checks and first‑article verification where repeatability and traceable standards matter. The robust construction and standard compliance support routine use in metalworking and fastening applications, ensuring threads meet the intended fit class. By integrating a purpose‑built gauge rather than ad‑hoc measuring methods, teams benefit from clearer quality metrics and fewer returns due to thread non‑conformance. Choose the Metav IndustryLine limit thread plug gauge for reliable, repeatable thread inspection — contact Metav Werkzeuge for technical advice and procurement at info@metav-werkzeuge.com or call +49 2822 7131930 Technical data SKU: M315.055.4 GTIN: 4054469123523 Type: Limit thread plug gauge Thread size: M55 x 1 Thread direction: right‑hand Standard: DIN 13, 6H Weight: 1.5 kg Facts Mass: 1.5 kg Thread nominal diameter: 55 mm Thread pitch: 1 mm Tariff code: 90173000 ECLASS: 21170235 Special features Material: gauge steel, hardened Metric ISO fine thread Go/no‑go verification for production use Category: Gauges / Thread gauges FAQ What is the intended use of this thread plug gauge? The limit thread plug gauge is intended for go/no‑go verification of metric ISO fine threads; the M55 x 1 gauge checks conformity with the DIN 13, 6H tolerance class. Does the gauge indicate which end is go and which is no‑go? Yes, the gauge is manufactured for standard go/no‑go operation so one end represents the acceptance limit and the other the rejection limit for the specified thread class. Is the material suitable for heavy daily use in a production environment? Made from hardened gauge steel, this Metav IndustryLine gauge is specified for robust, repeatable use and resists wear under routine inspection cycles. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
M55x1 Thread Gauge Ring, Metric ISO Fine Thread Right-Hand, DIN 13 6g, Hardened Gauge Steel - Metav IndustryLine
Take advantage of a hardened gauge built to DIN 13, tolerance 6g and a precise M55 x 1 mm thread form for reliable go/no-go verification; order the gauge directly via Metav Werkzeuge or consult the Metav team for application guidance. Thread ring gauge M55 x 1 mm (Go) — DIN 13, 6g, Metav IndustryLine A thread ring gauge M55 x 1 mm (Go) designed for verification of metric ISO fine threads in right‑hand form, suitable for production inspection and dimensional control. Hardened gauge steel construction Manufactured to DIN 13, tolerance 6g For metric ISO fine threads M55 x 1 Go ring for right‑hand threads Consistent acceptance testing for production quality The ring serves as a compact, robust tool for fast acceptance checks on threaded parts. Constructed from hardened gauge steel, it offers wear resistance that preserves the defined M55 x 1 mm thread profile over repeated use, which supports consistent production control. The Go condition confirms that threads do not exceed maximum material limits, enabling rapid in‑line decisions without time‑consuming measurement setups. This saves inspection time while maintaining repeatable quality criteria in series production. Clear traceable specifications to support inspection routines Built to DIN 13 with tolerance class 6g, the gauge provides a clearly defined reference that integrates directly into standard quality plans and inspection procedures. The mechanical design minimises elastic deformation under handling; at 2.1 kg the mass gives the ring a stable feel for bench checks and helps to avoid wobble during insertion. As a standardised physical master, the ring complements measurement instruments and statistical process control by offering a definitive pass/fail reference for metric ISO fine threads. Practical benefits for workshop and incoming goods control Adopting a dedicated ring gauge reduces complexity in everyday inspection tasks: a single check verifies thread form, pitch fit and major/minor diameter tolerances in one quick operation. The right‑hand orientation and fine‑pitch geometry make it particularly suited to components where tight pitch control is critical. The device is straightforward to store and handle and integrates into go/no‑go routines, providing an efficient balance between speed and unequivocal acceptance criteria for both production and incoming goods inspection. For precise thread verification, request the Metav IndustryLine M55 go ring from Metav Werkzeuge in Emmerich or ask their specialists for application advice via info@metav-werkzeuge.com or +49 2822 7131930 Technical data Article number: M315.155.4 GTIN: 4054469125190 Tariff number: 90173000 Mass/Size: M55 x 1 mm Weight: 2.1 kg Standard: DIN 13, 6g Facts Thread form: Metric ISO fine thread Tolerance class: 6g Orientation: Right‑hand thread Material: Hardened gauge steel Category: Lehren / Messstifte Special features Go (acceptance) ring design Robust construction for repeated use Suited to production and inspection environments FAQ What thread standard does this gauge check? The ring gauge checks metric ISO fine threads according to DIN 13 with tolerance class 6g, ensuring conformity with common industrial thread specifications. What does 'Go' mean for this ring gauge? 'Go' denotes acceptance of the maximum material condition; the M55 x 1 mm Go ring confirms that threaded parts can be assembled and do not exceed allowable limits. Which thread size and pitch does this device suit? This ring is specified for M55 x 1 mm threads and is manufactured for right‑hand metric ISO fine threads (SKU M315.155.4). What is the gauge made from and how durable is it? Constructed from hardened gauge steel, the gauge is designed for durability and repeatable inspection cycles; its mass and material resist wear and deformation during routine use. Where is this ring gauge typically used? The ring is used for rapid go/no‑go checks in production lines, incoming goods inspection and final quality control, providing a fast and unambiguous acceptance test for threaded parts. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
M55x2 Limit Go/No-Go Thread Plug Right Hand, Hardened Gauge Steel, DIN 13 6H - Metav IndustryLine
Product data inconsistent: the item is marked both as "good" and as "scrap" — please check and correct the source data. This discrepancy in the classification of the item may lead to confusion or errors in inventory management, reporting, or decision-making processes. It is essential to verify the accuracy of the source data to ensure consistency and reliability. Please review the relevant records, identify the root cause of the inconsistency, and update the data accordingly. Resolving this issue promptly will help maintain the integrity of the system and prevent potential complications in operations or analysis.
M55x2 Thread Gauge Ring Metric ISO Fine Pitch Right-Hand DIN 13 6g Hardened Gauge Steel - Metav IndustryLine
Benefit from the combination of DIN 13 conformity, hardened gauge steel and a compact, robust design for reliable thread verification in production and inspection. Order the thread ring gauge directly via Metav Werkzeuge or ask our consultants if needed. Thread ring gauge M55 x 2 mm (go) — DIN 13, 6g — Metav IndustryLine A Thread ring gauge M55 x 2 mm (go) for quick verification of external metric ISO fine threads in right‑hand form. Hardened gauge steel for long service life Conforms to DIN 13 tolerance class 6g Right‑hand go ring for external threads Solid design, convenient workshop handling Fast conformity checks for ISO metric threads The M55 x 2 mm go ring is manufactured to DIN 13 with tolerance 6g, providing a clear, objective pass criterion for external metric ISO fine threads. By using a dedicated go ring, inspection time is reduced because the decision is binary: the thread either accepts the gauge or it does not. This direct method supports inline quality control and process stability, making the gauge a pragmatic choice for production lines and inspection benches where repeatable verification and traceability are required. The implemented standard enables easy documentation of conformity in quality records. Robust material and form for repeatable results Constructed from hardened gauge steel, the ring resists wear and keeps its dimensional integrity under frequent use. The substantial mass (approx. 2.1 kg) and stiff body minimise handling deformation and support consistent engagement with the workpiece, which is especially beneficial when verifying larger external threads. The right‑hand configuration matches standard threaded parts and simplifies operator routines. Together, these attributes prolong the service interval and reduce rework caused by dubious measurements, translating into measurable savings in time and scrap. Practical integration into shop‑floor inspection Designed as a go ring for external threads, the tool fits established go/no‑go workflows and complements optical or tactile control methods. Traceability is supported by clear identification (SKU: M315.155.7, GTIN 4054469125206), facilitating inventory and calibration records. The combination of a standardised tolerance class and robust construction allows the gauge to be used both at the point of manufacture and in incoming goods inspection, enabling consistent accept/reject decisions and supporting quality assurance procedures. The item’s construction aims to reduce operator variability and streamline routine checks. Discuss application requirements or place an order through Metav Werkzeuge by calling +49 2822 7131930 or emailing info@metav-werkzeuge.com Technical Data Article number: M315.155.7 GTIN: 4054469125206 Label: Thread ring gauge M55 x 2 mm, go, right‑hand Facts Thread size: M55 x 2 mm Tolerance: DIN 13, 6g Weight: 2.1 kg Tariff number: 90173000 Materials & features Material: gauge steel, hardened Orientation: right‑hand external thread Type: go ring gauge for metric ISO fine threads Categories: Lehren (gauges); Messstifte FAQ What is the intended use of this ring gauge? The ring gauge is designed as a go ring for quick verification of external metric ISO fine threads M55 x 2 mm and is intended for production or inspection tasks where a pass/fail check is required. Which tolerance and standard apply to this gauge? Manufactured to DIN 13 with tolerance class 6g, the gauge provides a standardised acceptance criterion for external threads of the specified size. What material and durability features does the gauge offer? Made from hardened gauge steel, the ring gauge offers wear resistance and dimensional stability for frequent workshop use. How is traceability handled for the item? The product is identifiable by SKU M315.155.7 and GTIN 4054469125206, which supports inventory control and calibration records in quality management systems. Is the gauge suitable for automated inspection systems? The go ring is primarily a manual verification tool but can be integrated into automated processes where mechanical checks are required; suitability depends on the specific automation setup. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
M55x2 Thread Go Ring Gauge Metric ISO Fine Thread Right-Hand DIN 13, 6g Hardened Gauge Steel - Metav IndustryLine
Combine DIN 13 conformity, hardened gauge steel construction and the precise M55 x 2 mm sizing for consistent go/no‑go verification in production control. Order this thread ring gauge directly via Metav Werkzeuge or contact our consultants for specification support. Thread ring gauge M55 x 2 mm — No‑go, DIN 13, Metav IndustryLine A thread ring gauge M55 x 2 mm designed for rapid verification of metric ISO fine threads in right‑hand form for shop‑floor and inspection use Metric ISO fine thread M55 x 2 mm Conforms to DIN 13, tolerance 6g Hardened gauge steel construction Right‑hand no‑go ring, robust 1.4 kg Faster, traceable pass/fail inspection for fine threads This ring gauge provides a compact, unambiguous check for metric ISO fine threads with a nominal size of M55 x 2 mm. Built to the DIN 13 specification and manufactured to the 6g tolerance class, the device enables immediate go/no‑go decisions during incoming inspection or final part control. The unambiguous tactile and dimensional feedback speeds up routine checks, reduces downtime and eliminates subjective interpretation that can occur with non‑standard gauges. Robust materials for repeatable results over long service life Crafted from hardened gauge steel, the kit maintains form and accuracy under frequent use. The solid construction and a mass of 1.4 kg contribute to dimensional stability and minimise the influence of handling on the result, which helps preserve gauge life and repeatability. These material and mass characteristics reduce wear and help maintain conformity with the original inspection limits throughout repeated cycles on the shop floor. Easy integration into quality workflows and tooling sets As a purpose‑built ring gauge for right‑hand metric fine threads, the product fits seamlessly into established inspection processes and complements calipers and plug gauges in the metrology cabinet. Its straightforward pass/fail principle simplifies operator training and accelerates throughput in batch inspection. When documented traceability is required, the rigid design supports consistent results that can be referenced in quality records and production reports. For assured DIN 13 compliance and workshop‑ready gauging, order the Metav IndustryLine thread ring gauge via Metav Werkzeuge — our advisors at Metav Werkzeuge are available to confirm suitability for specific inspection tasks Technical data Article number: M315.255.7 GTIN: 4054469126869 Nominal thread: M55 x 2 mm Direction: right‑hand Weight: 1.4 kg Facts Standard: DIN 13 Tolerance class: 6g Tariff number: 90173000 Category: Gauges / Ring gauge Special features Material: hardened gauge steel Function: no‑go ring gauge for metric ISO fine threads Application: verification of threaded parts and production control Robust construction for repeated shop‑floor use FAQ What is the primary use of this ring gauge? The ring gauge is intended for go/no‑go verification of M55 x 2 mm metric ISO fine threads on finished parts and components. Which standard and tolerance does the gauge follow? This device is manufactured to DIN 13 and the tolerance class 6g, ensuring compatibility with standard metric fine thread specifications. What material is the gauge made from and why does it matter? Made of hardened gauge steel, the gauge offers wear resistance and dimensional stability, which preserves measurement reliability over repeated use. Is this gauge for right‑hand or left‑hand threads? The ring gauge is specified for right‑hand threads as indicated in the product description. Can this gauge be used on a production line for quick checks? Yes; the go/no‑go principle and robust construction make it suitable for fast, repeatable checks in production and incoming inspection. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
M56 x 1 mm Go Thread Ring, DIN 13 6g, Hardened Gauge Steel, Right-Hand - Metav IndustryLine
Take advantage of precise, standards‑compliant thread verification combined with robust, hardened construction for repeatable acceptance testing; order the ring gauge directly via Metav Werkzeuge or consult our specialists for application advice. Thread Ring Gauge M56 x 1 mm (Go) — DIN 13, 6g | Metav IndustryLine The Thread Ring Gauge M56 x 1 mm (Go) is a right‑hand metric fine‑thread inspection gauge for production and incoming‑inspection of threaded components. M56 x 1 mm metric fine thread DIN 13, tolerance class 6g Hardened gauge steel construction Ensures fast, reliable acceptance testing on the shop floor A dedicated go ring gauge like this offers a clear, rational acceptance criterion for threaded parts: if the M56 x 1 mm thread assemblies pass the gauge, they meet the specified form and pitch within DIN 13, 6g tolerances. This reduces ambiguity in quality control, shortens inspection cycles and lowers the risk of downstream assembly faults. The choice of hardened gauge steel provides dimensional stability under repeated use, ensuring that the inspection decision remains consistent over time — a decisive efficiency gain for production and quality departments. Designed for practical workshop integration and ease of use The ring gauge is configured as a straightforward inspection tool that integrates directly into routine checks. Its compact, balanced mass (approx. 1 kg) and right‑hand geometry make it simple to handle during manual inspection steps or transfer checks at assembly stations. The physical "go/no‑go" nature removes the need for interpretation, helping standard operators and inspectors make rapid, unambiguous decisions. This clarity supports smoother workflows and reduces rework, delivering measurable time savings across batch inspections. Built for longevity and standards conformity Manufactured from hardened gauge steel, the gauge resists wear from repeated engagement with threaded parts, extending service life and maintaining accuracy. Compliance with DIN 13 and tolerance class 6g means the instrument aligns with established metric ISO fine‑thread specifications, supporting both internal quality systems and external audit requirements. The construction and specifications combine to offer a durable, traceable inspection solution that fits within industrial quality routines and product conformity documentation. For robust thread inspection with Metav IndustryLine quality, contact Metav Werkzeuge for expert guidance and reliable supply from Emmerich. Technical data Article number: M315.156.4 GTIN: 4054469125220 Tariff code: 90173000 Data Thread size: M56 x 1 mm Tolerance class: 6g Weight: 1 kg Special features Material: hardened gauge steel Standard: DIN 13 Type: right‑hand metric fine thread Function: Go ring gauge FAQ What is the purpose of this ring gauge? The Thread Ring Gauge M56 x 1 mm (Go) is used to verify that metric fine‑threaded components conform to the DIN 13, 6g acceptance limits for production and incoming inspection. Can this gauge be used for assembly checks on finished parts? Yes, the gauge serves as a direct acceptance tool in assembly‑line checks; the Metav IndustryLine ring gauge provides a simple go/no‑go verdict for threaded assemblies. What material is the gauge made from and why does it matter? The ring is manufactured from hardened gauge steel, chosen for wear resistance and dimensional stability to ensure repeated, reliable inspection results. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
M56x0.5 Thread Limit Plug Gauge For Metric ISO Fine Thread, Right-Hand, Hardened Gauge Steel, DIN 13 6H - Metav IndustryLine
Robust hardened gauge steel and DIN 13 (6H) tolerance ensure repeatable, rapid pass/fail checks of metric ISO fine internal threads; the compact, solid design (1.8 kg) improves handling and stability on the shop floor. Order the gauge directly via Metav Werkzeuge or ask our consultants for application advice. Limit thread plug gauge M56×0.5 — plug gauge for metric ISO fine internal threads, right‑hand (Metav IndustryLine) The Limit thread plug gauge M56×0.5 is a right‑hand go/no‑go plug gauge intended for quick inspection of metric ISO fine internal threads in production, incoming inspection and quality control. Hardened gauge steel construction DIN 13 standard, tolerance 6H Metric fine thread M56×0.5 right-hand Solid 1.8 kg mass for stable handling Rapid conformity checks to reduce rework and downtime A limit plug gauge is a straightforward go/no‑go tool that delivers immediate, binary results: the go end confirms that the internal thread meets minimum dimensions, while the no‑go end indicates excessive deviation. This direct method accelerates inspection routines, reduces subjective judgement and shortens hold times in production. Using a gauge built to DIN 13 with tolerance 6H gives a defined, industry‑recognised acceptance window, which translates into fewer returns and lower scrap rates when implemented as part of routine quality checks. Durable construction for consistent shop‑floor performance Made from hardened gauge steel, the instrument resists wear and maintains dimensional stability under repeated use. Its solid construction, reflected in a mass of 1.8 kg, helps the tool seat correctly during insertion and minimises vibration or misalignment that can compromise judgement. The robust finish and gauge‑grade material simplify handling in industrial environments and extend service life, so calibration intervals are driven by actual use rather than premature deterioration. Easy integration into inspection processes and fixtures The plug gauge is suitable for inline checks, receiving inspection benches and manual quality stations where rapid pass/fail decisions are required. Compatibility with metric ISO fine threads makes it a pragmatic choice for components specified to M56×0.5, enabling standardised acceptance criteria across suppliers and production lines. As a tactile, mechanical reference, the gauge complements dimensional instruments and optical checks by providing a functional verification of thread fit under real assembly conditions. Peace of mind through proven supply and expertise Sourcing the gauge from Metav IndustryLine links the tool to an established distribution and quality filter based in Emmerich, ensuring consistent availability and traceable product provenance. The combination of recognised standards, sturdy materials and practical design supports a workflow that values repeatability and clear decision criteria—key factors for workshops, toolrooms and production plants that prioritise trustworthy inspection tools. Contact Metav Werkzeuge for delivery from Emmerich or request technical advice on the Metav IndustryLine limit thread plug gauge M56×0.5 — expert guidance and prompt supply available Technical data Article number: M315.056.2 GTIN: 4061905047817 Material: hardened gauge steel Standard: DIN 13, 6H Net weight: 1.8 kg Tariff number: 90173000 Facts Thread size: M56 × 0.5 Pitch: 0.5 mm Mass: 1.8 kg Special features Right‑hand thread Category: Gauge pins; Gauges (plug gauges) Intended use: metric ISO fine internal threads FAQ How does a limit plug gauge indicate whether a thread is acceptable? A limit plug gauge uses a go/no‑go principle: the go end must engage smoothly to confirm minimum dimensional conformity, while the no‑go end must not fit if the thread is within tolerance. The limit thread plug gauge M56×0.5 provides this clear pass/fail check for internal metric ISO fine threads. Is this gauge suitable only for M56×0.5 threads? This specific gauge is designed for the M56×0.5 metric ISO fine thread; the Metav IndustryLine range includes other sizes for different thread dimensions and pitches. What does DIN 13, 6H specify for inspection? DIN 13 defines profile and dimensional characteristics for metric threads; the tolerance class 6H sets the acceptable internal thread limits. Using a gauge manufactured to these standards ensures inspection aligns with established engineering tolerances. How should the gauge be stored and cared for to maintain accuracy? Store the plug gauge in a dry, clean environment and protect it from mechanical damage. Wipe with a soft cloth and light protective oil after use; avoid dropping or using it as an assembly tool to preserve the hardened surfaces and dimensional fidelity. Can this plug gauge be used during production cycle checks? Yes. The gauge is suitable for in‑process and final inspections where quick, repeatable go/no‑go checks are required, providing reliable functional verification of thread fit. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
M56x1 Go/No-Go Thread Plug Gauge Metric ISO Fine Thread Right-Hand, Hardened Gauge Steel, DIN 13 6H - Metav IndustryLine
Take advantage of the combination of hardened gauge steel, precise DIN 13 / 6H tolerance and clear go/no-go verification for fast, reliable thread inspection; order the limit thread plug gauge M56 x 1 mm directly via Metav Werkzeuge or ask our consultants if needed. Limit thread plug gauge M56 x 1 mm, right-hand — Metav IndustryLine The limit thread plug gauge M56 x 1 mm is a right-hand go/no-go gauge designed for rapid verification of metric ISO fine threads in production and incoming inspection. Metric ISO fine thread M56×1 Hardened gauge steel construction Right-hand thread go/no-go check Compliant with DIN 13, tolerance 6H Fast, reproducible verification for shopfloor quality control The plug gauge is engineered for immediate, unambiguous inspection: a part that accepts the "go" end but is stopped by the "no-go" end meets the specified thread form and pitch. Manufactured from hardened gauge steel, the tool sustains repeated use while keeping dimensional stability, which reduces rework and scrap. The M56 x 1 mm thread form, paired with the DIN 13 / 6H tolerance class, ensures compatibility with standard metric fine-threaded components used in mechanical assemblies, fixtures and serial production. Robust design that minimises downtime A clear benefit of this gauge is its robust construction and handling characteristics. The plug assembly is finished to resist wear and maintain gaugeability over long inspection runs; the relatively substantial mass (1.8 kg) contributes to stable contact during checking. As a right-hand thread instrument, the item mirrors the parts most commonly produced, enabling straightforward, repeatable checks that help maintain steady production throughput and reduce measurement variation across shifts. Intuitive use reduces cycle time and training needs Go/no-go plug gauges are deliberately simple to operate: the "go" end must enter freely, while the "no-go" end must not. This binary result removes interpretation ambiguity and speeds decision-making on the shopfloor, offering a faster alternative to full-form measurement or optical inspection for routine checks. The design supports fast acceptance testing during assembly and incoming goods inspection, improving process efficiency without requiring complex measurement training. Standards traceability and Metav support for integration The gauge is produced to match DIN 13 thread specifications and is identified by its GTIN for traceability within procurement and inspection systems. Supplied under the Metav IndustryLine label, the plug gauge benefits from Metav’s quality assurance and logistical reach: a reliable partner for workshops that require consistent measurement tools. For specialised applications or integration into existing inspection routines, Metav’s product advisers can provide guidance on appropriate inspection intervals and handling to prolong service life. For reliable thread inspection on the shopfloor, request the Metav IndustryLine limit thread plug gauge M56 x 1 mm from Metav Werkzeuge — Metav Werkzeuge’s specialists in Emmerich will advise on selection and routine use to secure consistent production quality. Technical Data Article number: M315.056.4 Manufacturer: Metav IndustryLine GTIN: 4054469123554 Tariff number: 90173000 Facts Weight: 1.8 kg Thread: M56 x 1 mm Tolerance class: 6H (DIN 13) Special features Material: hardened gauge steel Right-hand thread configuration Go/no-go plug gauge for metric ISO fine threads Intended for production and incoming inspection FAQ What thread size does this gauge check? The limit thread plug gauge checks metric ISO fine threads of size M56 x 1 mm, as stated on the Metav IndustryLine product label. How is a pass or fail determined with this plug gauge? Pass/fail is determined by the go/no-go principle: the go end must enter the thread, the no-go end must not; this quick check is the standard use for the M56 x 1 mm plug gauge. Which standard does the gauge conform to? The gauge is manufactured to match DIN 13 specifications and the tolerance class 6H, ensuring conformity with common metric thread standards. What material is the gauge made from? The instrument is made from hardened gauge steel, chosen for wear resistance and dimensional stability in repeated inspection cycles. Is this gauge suitable for production-line inspection? Yes — the Metav IndustryLine limit plug gauge M56 x 1 mm (Article M315.056.4) is intended for fast, repeatable checks in production and incoming inspection settings. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
M56x1 Thread Ring Gauge Go, Metric ISO Fine Pitch, Right-Hand, Hardened Gauge Steel, DIN 13 6g - Metav IndustryLine
Take advantage of the precision of DIN 13 tolerance class 6g, the durability of hardened gauge steel and the exact fit for M56 x 1 mm metric ISO fine threads — a robust choice for repeatable thread inspection. Order the gauge directly via Metav Werkzeuge or consult our specialists for application advice. Thread Ring Gauge M56 x 1 mm — Metric ISO fine thread gauge, DIN 13, 6g (Metav IndustryLine) A Thread Ring Gauge M56 x 1 mm for dimensional inspection of metric ISO fine threads, delivered as a right‑hand gauge manufactured to DIN 13 with tolerance class 6g. Hardened gauge steel for long-term stability Precision to DIN 13 tolerance class 6g Suitable for M56 x 1 mm metric ISO fine threads Right‑hand thread checking, workshop grade Consistent conformity reduces rework and rejects Manufactured to DIN 13 and the tolerance class 6g, this ring gauge provides a verifiable limit for acceptance testing that integrates directly into standard quality routines. The defined metric ISO fine‑thread geometry ensures that checks are consistent with engineering drawings and inspection plans; using the gauge removes ambiguity from go/no‑go assessments and supports traceable measurement processes in production and incoming inspection. Durable construction for sustained accuracy Made from hardened gauge steel, the device resists wear and maintains its functional form over prolonged use, which reduces measurement drift and the need for frequent replacement. The solid construction, reflected in a mass of 1.4 kg, gives a stable handling feel and reduces the influence of accidental deformation during handling. These material and design choices translate into lower lifetime cost and fewer interruptions for recalibration or corrective actions. Integrates into workshop inspection workflows Designed for routine use in machine shops, toolrooms and quality control benches, the gauge speeds up inspection cycles by offering an immediate mechanical check of thread form and fit. The right‑hand orientation aligns with common threaded component production and allows rapid verification during assembly or post‑machining checks. With clear conformity criteria and robust fabrication, the gauge supports higher throughput and more reliable first‑article inspection results. For certified thread inspection tasks, request the Metav IndustryLine M56 x 1 mm ring gauge from Metav Werkzeuge for dependable stock availability and expert guidance on integration into existing inspection procedures. Technical data Article number: M315.256.4 GTIN: 4054469126883 SKU: M315.256.4 Facts Diameter: 56 mm Pitch: 1 mm Weight: 1.4 kg Standard / Tolerance: DIN 13, 6g Tariff code: 90173000 Special features Material: hardened gauge steel Thread type: metric ISO fine thread, right‑hand Category: gauges / inspection tools Intended use: dimensional inspection of threads FAQ What tolerance class does this gauge check? The ring gauge is manufactured to DIN 13 and verifies threads to tolerance class 6g, suitable for standard metric ISO fine‑thread checks. Is the gauge suitable for M56 x 1 mm fine threads on production parts? Yes, the Metav IndustryLine ring gauge is designed specifically for M56 x 1 mm metric ISO fine threads and is intended for workshop and production inspection. What material is the gauge made from and how does that affect longevity? The gauge is produced from hardened gauge steel, offering high wear resistance and long service life under normal inspection use. Can this ring gauge be used for right‑hand and left‑hand threads? This particular item is a right‑hand thread gauge; left‑hand variants must be specified separately. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
M56x2 mm Go/No-Go Thread Plug Gauge Metric ISO Fine Pitch Right-Hand, Hardened Gauge Steel, DIN 13 6H - Metav IndustryLine
The supplied product data contains contradictory status information and cannot be processed into a reliable product description. Specifically, the item is simultaneously flagged as both rejected/scrap and as being in good condition, which creates an unresolvable inconsistency for quality, stock and presentation purposes. Before a full, compliant product text can be produced, the source data must be reviewed and corrected so that condition and status fields are consistent and any anomalous pricing entries are clarified. Please verify the original dataset and resubmit the corrected information; if assistance is required to resolve the discrepancy or to supply missing verification details, contact Metav Werkzeuge for support at info@metav-werkzeuge.com or by telephone on +49 2822 7131930. Once the data is consistent, a complete product description can be generated.
M56x2 Thread Gauge Ring Go Right-Hand ISO Metric Fine Thread DIN 13, 6g Hardened Gauge Steel - Metav IndustryLine
Take advantage of fast, reproducible thread inspection combined with hardened gauge steel and DIN 13 / 6g conformity for consistent quality control on metric fine threads; order directly via Metav Werkzeuge or consult our specialists for application advice. Thread ring gauge M56 x 2 mm — no-go ring, hardened gauge steel (Metav IndustryLine) The Thread ring gauge M56 x 2 mm is a dedicated no-go ring intended for rapid verification of right‑hand metric ISO fine external threads in production and inspection. No-go ring for M56 x 2 mm metric fine threads Conforms to DIN 13 tolerance class 6g Manufactured from hardened gauge steel for wear resistance Designed for right-hand external thread inspection Keep out non-conforming threads with a simple check A no-go ring gauge offers an unambiguous, tactile test that immediately separates suspect parts from accepted ones. Applied to external threads, the ring must not fit if the thread is within the maximum material condition; if the ring goes on, the thread exceeds the allowable limit and is rejected. This method removes subjective judgement from the line and provides a fast, repeatable inspection step that fits into both high‑volume production and small-series quality checks. The compact testing routine reduces inspection time without sacrificing reliability. Built for longevity and standard conformity Constructed from hardened gauge steel, this ring resists wear and preserves the verification limit over many cycles, keeping recalibration intervals predictable. Compliance with DIN 13 and the 6g tolerance class ensures direct comparability with common metric ISO fine-thread specifications, so measured parts and gauges share a clear reference framework. Using a gauge that matches recognised standards simplifies audit trails and documentation for quality management systems. Practical advantages in the workshop and at the production line The simple geometry and solid construction make the gauge straightforward to handle and store; its mass provides stable engagement during the test. Because the tool is a dedicated no‑go ring for a right‑hand M56 x 2 mm pitch, inspection steps are minimised and throughput is improved — non‑conforming parts are identified immediately, lowering the risk of downstream assembly issues and reducing rework or scrap. For process engineers, the instrument integrates easily into go/no‑go test benches or manual quality control stations, supporting a robust first‑pass yield strategy. Specify the Metav IndustryLine no‑go ring gauge for dependable thread control — contact Metav Werkzeuge in Emmerich for supply and application guidance Technical Data Article number: M315.256.7 GTIN: 4054469126890 Weight: 1.4 kg Material: Gauge steel, hardened Standard: DIN 13, 6g Facts Thread size: M56 x 2 mm Tolerance class: 6g Thread hand: Right‑hand Tariff number: 90173000 Special features No‑go ring for external metric ISO fine threads Suitable for rapid go/no‑go inspections Wear‑resistant hardened construction Category: Gauges / Ring gauges FAQ What is the primary function of this ring gauge? The no‑go ring gauge is used to check external threads: it must not fit a compliant thread, so any part that accepts the ring is rejected as out of tolerance. Which thread form and size does this gauge inspect? This gauge is intended for M56 x 2 mm right‑hand metric ISO fine threads, manufactured to DIN 13 with a tolerance class of 6g. What material is the gauge made from and why does it matter? The ring is made from hardened gauge steel, chosen for its wear resistance and stability so that the inspection limit remains consistent over many uses. Can this gauge be integrated into a production inspection routine? Yes; the simple pass/fail nature of the no‑go ring makes it well suited to both manual checks and automated go/no‑go stations where quick, repeatable decisions are needed. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
M56x2 Thread Ring Gauge Metric ISO Fine Right-Hand, Go, Hardened Gauge Steel, DIN 13 6g - Metav IndustryLine
Take advantage of a hardened gauge-steel construction and the DIN 13 (6g) tolerance to ensure rapid, reliable pass/fail checks on metric ISO fine threads; order directly via Metav Werkzeuge or consult our specialists for application advice. Thread ring gauge M56 x 2 mm (Go) — DIN 13, 6g The Thread ring gauge M56 x 2 mm is a go gauge designed for acceptance and in-process inspection of metric ISO fine threads in industrial and workshop environments. DIN 13 tolerance class 6g Go gauge for M56 x 2 mm threads Hardened gauge steel construction Suitable for workshop and inspection use Accurate verification for ISO fine threads The ring functions as a dedicated go gauge for metric ISO fine threads, ensuring that external threads meet the specified fit defined by DIN 13 and tolerance class 6g. By providing an unequivocal pass condition, the gauge reduces decision time at the inspection bench and limits subjective judgement during sampling. The direct result is fewer downstream rejects and smoother assembly processes, since only parts that enter without interference proceed to assembly. Durable build that pays back in uptime Manufactured from hardened gauge steel, the tool resists wear under repeated use and retains thread form over long inspection cycles. The solid construction, reflected in its 2.0 kg mass, improves handling stability during checks and lowers the risk of deformation that could compromise results. Long service life of the gauge translates into fewer tool replacements and consistent quality control data across production batches. Quick integration into inspection workflows Designed for straightforward go/no-go checks, the gauge simplifies routine inspection: a correct fit confirms conformance, a refusal to enter flags non-conforming threads. This binary result speeds up operator decisions and integrates easily with existing inspection protocols. When documented inspection is required, the gauge’s clear function supports traceable quality records and complements established measurement routines without the need for complex fixturing. Trusted sourcing and availability for production Supplied under the Metav IndustryLine portfolio, the gauge is backed by a distribution and quality filter located in Emmerich that supports industrial buyers with reliable stock and clear product data. The combination of an established manufacturing standard, robust materials and dependable supply reduces procurement risk and helps maintain uninterrupted production and inspection capacity. Contact Metav Werkzeuge today to request further technical details about the Metav IndustryLine thread ring gauge M56 x 2 mm or to discuss suitability for specific production threads Technical data Article number: M315.156.7 SKU: M315.156.7 GTIN: 4054469125237 Label: Gewinde-Lehrring M56 x 2 mm gut DIN 13, f. metr. ISO-Feingewinde, rechts Facts Thread size: M56 x 2 mm Weight: 2.0 kg Tariff number: 90173000 Tolerance class: 6g Special features Material: hardened gauge steel Go gauge for metric ISO fine threads Right-hand thread design Conforms to DIN 13 Category: Gauges / Thread gauges FAQ What does the gauge check and what standard does it follow? The ring checks external metric ISO fine threads to the DIN 13 standard; it is configured as a go gauge for the M56 x 2 mm size. Is this gauge suitable for use in a daily inspection routine? Yes — the hardened construction and clear go/no-go function make this gauge appropriate for workshop and production-line inspection. Will the ring gauge accept left-hand threads? No — this tool is manufactured for right-hand threads and is intended specifically for standard right-hand metric ISO fine threads. How robust is the material for repeated use? Made from hardened gauge steel, the gauge is designed for wear resistance and long service life under regular inspection cycles. Can the gauge be used to verify fit class other than 6g? This specific item is manufactured to tolerance class 6g per DIN 13; other tolerance classes require the corresponding gauge variant or set. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
M56x5.5 Thread Limit Gauge Plug, Right-Hand, Hardened Gauge Steel, DIN 13 6H - Metav IndustryLine
Combine repeatable thread acceptance with hardened gauge steel construction and conformity to DIN 13, 6H to secure reliable production control. Benefit from a compact inspection tool that speeds up go/no-go checks and reduces rework—order directly via Metav Werkzeuge or consult our technical advisers for application guidance. Limit thread plug gauge M56 x 5.5 (right-hand) — Metav IndustryLine Limit thread plug gauge M56 x 5.5 for right-hand metric ISO threads, designed for rapid acceptance testing and in-process inspection in workshop and production environments For M56 x 5.5 metric ISO threads Hardened gauge steel construction Right-hand thread, go/no-go acceptance Complies with DIN 13, tolerance 6H Reliable acceptance testing for threaded parts The limit thread plug gauge offers a straightforward and highly efficient method for go/no-go inspection of internal threads. Built to the M56 x 5.5 metric ISO specification, the gauge enables immediate determination of whether a threaded bore meets the required form and pitch tolerances. By relying on a proven limit-gauge approach rather than time-consuming measurement routines, production lines can maintain throughput while ensuring each part fulfils the intended thread class. Conformance to DIN 13 with a 6H tolerance level supports consistent decision-making during quality control and simplifies compliance documentation. Durable construction for repeatable measurements Constructed from hardened gauge steel, the plug is designed to resist wear from repeated engagement, preserving the gauge profile and extending service life. The material choice reduces the rate of dimensional drift under normal workshop handling and contributes to fewer false rejections over time, which in turn lowers scrap and rework costs. The right-hand metric ISO configuration ensures compatibility with standard fastener systems and fixtures used in machine building and assembly shops, while the compact form factor makes the tool easy to store and handle between inspection points. Integrating the gauge into quality workflows A limit plug acts as a rapid acceptance device within sampling plans and 100% inspection processes alike. Used as a go/no-go check, the gauge provides an immediate binary outcome: acceptable or not acceptable. This speeds up on-machine checks, first-article inspections and incoming part verification without replacing periodic dimensional audits that use comparators or gauges with traceable calibration. The simplicity of the test reduces operator training and eliminates the need for elaborate measuring setups, offering a pragmatic balance between control and operational efficiency. Practical handling, care and traceability Handling is straightforward: engage the plug into the threaded bore to confirm acceptance; any binding or failure to enter signals a non-conforming thread. Routine care—cleaning the threads before inspection and protecting gauge faces from nicks—helps preserve accuracy. For traceable records, maintain a log of inspections and store the plug in a protective sleeve when not in use. The robust profile and hardened finish ensure the tool withstands regular use in production environments while delivering consistent tactile feedback during go/no-go checks. For dependable thread acceptance with Metav IndustryLine, contact Metav Werkzeuge in Emmerich for tailored advice and stock information from our technical team. Technical data Article number: M315.056 GTIN: 4054469123547 ECLASS: 21170235 Facts Thread: M56 x 5.5 Tolerance: 6H (DIN 13) Tariff number: 90173000 Special features Material: Gauge steel, hardened Right-hand metric ISO thread Category: Limit gauges / Thread plug gauge FAQ What is the intended use of this limit thread plug gauge? The limit thread plug gauge M56 x 5.5 is intended for go/no-go acceptance testing of internal threads to verify conformity with the M56 x 5.5 metric ISO specification and DIN 13 tolerance class 6H. How is wear managed and what maintenance is required? Regular cleaning, protected storage and routine visual inspection are recommended; the hardened gauge steel construction of the Metav IndustryLine plug reduces wear and helps maintain reliable performance. Can the gauge be used on left-hand threads? No, this gauge is manufactured as a right-hand thread plug and is suitable only for right-hand metric ISO thread acceptance. Does the tool replace dimensional measurement for documentation? The limit plug provides rapid acceptance results for production control but does not replace detailed dimensional measurement when traceable dimensional data are required for certification or calibration records. Which standards does the gauge comply with? The thread profile and tolerance correspond to DIN 13 with a 6H tolerance, matching common metric ISO thread acceptance practices. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
M56x5.5 Three-Point Go Thread Ring Gauge, DIN 13 6g, Hardened Gauge Steel - Metav IndustryLine
Take advantage of fast, unambiguous pass/fail checks thanks to the combination of hardened gauge steel, clear DIN 13 6g tolerance and exact M56 x 5.5 sizing for reliable thread inspection. Order the ring gauge directly via Metav Werkzeuge or consult our technical team for application advice. Thread ring gauge M56 x 5.5 mm — Go gauge, DIN 13 6g (right-hand) — Metav IndustryLine The Thread ring gauge M56 x 5.5 mm Go is a right‑hand inspection ring for ISO metric threads, engineered for quick production checks and laboratory verification of threaded components. Go thread gauge M56 x 5.5, right-hand Hardened gauge steel construction Tolerance per DIN 13, 6g Precision inspection tool for ISO threads Rapid, reliable pass/fail inspection on the shop floor A dedicated go gauge significantly reduces cycle time for quality checks by turning thread inspection into an immediate pass/fail decision. The hardened construction and standardised DIN 13 tolerance class mean that the gauge keeps its form under repeated use, maintaining repeatability and limiting measurement uncertainty in routine control tasks. This inspection ring is intended for rapid verification of threaded parts produced to ISO metric specifications, enabling operators to focus on productivity without compromising conformity. Durable manufacture for sustained accuracy and low life‑cycle cost Made from hardened gauge steel, the ring is built to withstand frequent handling and contact with machined parts. The material choice and heat treatment extend service life and reduce the need for premature replacement, delivering a favourable cost‑of‑ownership in demanding production environments. The right‑hand configuration and clear sizing of M56 x 5.5 allow straightforward integration into existing inspection stations, supporting a stable quality routine with minimal operator training. Traceable standards and predictable integration into quality systems Compliance with DIN 13, 6g places the ring gauge within a recognised tolerance framework for ISO metric threads, simplifying documentation and acceptance criteria in production and inspection plans. As a purpose‑built inspection instrument, the gauge supports consistent batch sampling and in‑process control, providing engineers and inspectors with a robust means of safeguarding assembly and functional fit. For purchasers requiring further technical details, Metav IndustryLine supplies the necessary product identifiers for inventory and traceability. Contact Metav Werkzeuge for a quotation or technical consultation on the Metav IndustryLine M56 go ring gauge: info@metav-werkzeuge.com | +49 2822 7131930 Technical data Article number: M315.156 SKU: M315.156 GTIN: 4054469125213 Brand: Metav IndustryLine Material: gauge steel, hardened Thread size: M56 x 5.5 mm Thread hand: right-hand Standard: DIN 13, 6g Weight: 2 kg Tariff number: 90173000 Facts Weight: 2 kg Thread nominal diameter: 56 mm Thread pitch: 5.5 mm Tariff number: 90173000 Special features Go (pass) ring gauge For ISO metric threads, right-hand Hardened gauge steel construction Category: Gauges; Inspection pins Intended for rapid pass/fail checks FAQ What does "Go" mean for this ring gauge? The Go designation indicates the ring is used to verify that an external thread fits within the allowed maximum material condition; the Thread ring gauge M56 x 5.5 mm should pass onto a correct part without force, confirming conformance to the specified limit. Which thread form and tolerance class does the gauge check? This ring checks ISO metric threads to DIN 13 with tolerance class 6g, suitable for general engineering threads produced to the ISO metric standard. Can the gauge be used in production environments with frequent checks? Yes, the hardened gauge steel construction is designed for repeated use in production and inspection stations, offering consistent performance and extended service life for routine checks. How is the gauge applied during inspection? For external threads, the part is engaged with the Go ring; the part is acceptable if it screws into the gauge smoothly to the seating face. Any resistance or inability to fit indicates a non‑conforming thread. Is this gauge suitable for right‑hand and left‑hand threads? This specific ring is manufactured for right‑hand ISO metric threads; left‑hand threads require a corresponding left‑hand ring gauge or the appropriate variant. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
M56×5.5 Thread Ring Gauge 6g Right-Hand, DIN 13 - Metav IndustryLine
Take advantage of fast, unequivocal pass/fail inspection thanks to the combination of hardened gauge steel and the DIN 13, 6g tolerance class; this keeps assembly lines moving while reducing rework. The precise right‑hand thread control provided by the no‑go function protects product conformity and shortens inspection time. Order the thread gauge directly via Metav Werkzeuge or ask our consultants if needed. Thread Ring Gauge M56 × 5.5 — No‑go ring, DIN 13 (6g) — Metav IndustryLine The Thread Ring Gauge M56 × 5.5 is a hardened no‑go ring for rapid verification of right‑hand metric ISO coarse threads in production and inspection environments. Hardened gauge steel construction DIN 13 tolerance class 6g Right‑hand metric thread M56×5.5 Ensure consistent thread conformity on the production line The no‑go ring performs a single, decisive check of external threads: if the gauge will not enter, the thread falls within the upper limit defined by DIN 13 (6g). Built from hardened gauge steel, the device resists wear and preserves the calibrated limit over many inspection cycles, which translates into fewer false rejects and more predictable downstream assembly. Specifying a dedicated no‑go ring for the M56 × 5.5 pitch reduces interpretation time compared with optical or tactile measurements and supports a lean inspection routine that focuses on clear go/no‑go outcomes. Robust shop‑floor performance with repeatable results Designed for repetitive use in workshops and production cells, this inspection ring prioritises simplicity and reliability. The hardened construction and precise thread form produce a tactile, unambiguous result at the workbench: a pass is quick to confirm, a fail is immediate and actionable. That operational clarity speeds quality gates and helps maintain throughput without compromising measurement integrity. The right‑hand orientation and standard metric sizing make the ring easy to integrate into established workflows and fixtures. Practical quality assurance and integration into inspection routines For routine checks, the ring gauge offers a compact, low‑effort solution to maintain traceable manufacturing tolerances. Reference marks such as SKU and GTIN facilitate inventory control and documentable audit trails when paired with a shop’s quality records. The instrument supports a pragmatic approach to quality: fast checks at critical stages prevent defective parts reaching assembly, while also simplifying training for operators. For application guidance or compatibility questions regarding specific thread fits, consult the technical information supplied with the gauge or contact Metav Werkzeuge for tailored advice. For assured thread control and practical inspection advice, request the Metav IndustryLine no‑go ring from Metav Werkzeuge in Emmerich or consult our specialists to confirm fitment and handling recommendations. Technical data Article number: M315.256 GTIN: 4054469126876 Thread: M56 × 5.5 mm Standard: DIN 13, 6g Type: No‑go ring gauge Material: hardened gauge steel Right‑hand thread Tariff number: 90173000 Facts Category: Gauges / Inspection Eclass: 21170214 Special features For metric ISO coarse thread Right‑hand orientation Hardened gauge steel Image available FAQ What does a no‑go ring gauge check on a threaded component? A no‑go ring gauge verifies that the external thread does not exceed the maximum material condition; the Thread Ring Gauge M56 × 5.5 (Metav IndustryLine, SKU M315.256) provides an immediate fail if the thread is oversized or malformed. Which standard and tolerance class apply to this gauge? The gauge is manufactured to DIN 13 with tolerance class 6g, intended for metric ISO coarse threads of size M56 × 5.5. Can this ring gauge be used for any material? The ring checks thread geometry and major diameter independently of component material; the Thread Ring Gauge M56 × 5.5 is suitable for inspection of parts made from metals and other materials provided the thread form matches the specified ISO profile. How is the no‑go result interpreted on the shop floor? If the no‑go ring does not enter the threaded part, the thread is within the accepted upper limit; if the ring enters, the part requires rework or rejection. The instrument gives a direct go/no‑go decision to support rapid quality control. Metav IndustryLine: Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
M58x2 Thread Gauge Ring Go Metric ISO Fine Thread Right Hand, Hardened Gauge Steel DIN 13 6g - Metav IndustryLine
Take advantage of a proven inspection tool that combines hardened gauge steel construction, a clear DIN 13, 6g tolerance class and the exact M58 x 2 mm form for reliable pass/no‑go checks; order directly via Metav Werkzeuge or consult our specialists for application advice. Go thread ring gauge M58 x 2 mm — hardened gauge steel, DIN 13 (6g) The Go thread ring gauge M58 x 2 mm is a precision inspection ring for metric ISO fine threads, designed for right‑hand thread verification in production and incoming inspection. M58 x 2 mm metric fine thread DIN 13 tolerance grade 6g Hardened gauge steel construction Right‑hand go ring for pass inspection Consistent pass/no‑go assessment for metric fine threads A go thread ring gauge offers a fast, objective pass/no‑go decision during routine inspections. The M58 x 2 mm nominal size and the DIN 13 specification with tolerance grade 6g ensure that only threads within the permitted dimensional envelope are accepted. Using a ring gauge for “go” checks reduces subjective interpretation and speeds up batch verification, improving throughput while maintaining measurable conformance to the applicable standard. Durable construction to withstand frequent use Manufactured from hardened gauge steel, the ring resists wear and maintains its functional dimensions over extended use, supporting reproducible inspections on the shop floor. The solid mass (approx. 2.2 kg) lends stability during handling and helps ensure alignment when mating with threaded parts. Robust material selection and heat treatment translate into a long service life, reducing downtime for replacement and supporting a predictable maintenance schedule. Seamless integration into quality workflows As a dedicated right‑hand go ring for metric ISO fine threads, this gauge slots into incoming inspection, in‑process checks and final quality control without the need for complex setup. The straightforward pass/no‑go principle simplifies operator training and enables rapid decisions at the machine or inspection station. When traceability or inventory identification is required, the ring can be logged by SKU M315.158.7 and GTIN for process documentation and audit trails. Choose the Metav IndustryLine go ring gauge for robust, standards‑compliant thread inspection and contact Metav Werkzeuge for delivery timing and technical guidance tailored to production needs Technical data Article number: M315.158.7 GTIN: 4054469125244 Label: Gewinde‑Lehrring M58 x 2 mm gut DIN 13, f. metr. ISO‑Feingewinde, rechts Weight: 2.2 kg Material: Lehrenstahl, hardened Numbers / Core technical data Nominal diameter: 58 mm Pitch: 2 mm Tolerance grade: 6g Tariff number: 90173000 Special features Go gauge for pass inspection Right‑hand thread design Complies with DIN 13 Category: Gauges / Ring gauges FAQ What is the primary purpose of this ring gauge? The ring is intended for go checks of metric ISO fine threads; the M58 x 2 mm gauge confirms whether a right‑hand thread meets the DIN 13, 6g acceptance criteria. Which standard does the gauge conform to? The gauge is manufactured to the requirements of DIN 13 and matched to tolerance class 6g for metric ISO fine threads. Is this gauge suitable for production use? Yes. The hardened gauge‑steel construction and solid mass make the ring suitable for regular shop‑floor inspections and high‑volume production checks. Can the ring gauge verify left‑hand threads? This specific item is a right‑hand go ring; left‑hand thread checks require a correspondingly specified left‑hand gauge. How is the gauge identified for stock and traceability? The item is listed as SKU M315.158.7 and GTIN 4054469125244 for inventory control and documentation purposes. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
M58x2 Thread Go Gauge For Metric ISO Fine Thread, Right-Hand, Hardened Gauge Steel, DIN 13 6H - Metav IndustryLine
Reliable thread verification combined with hardened gauge steel construction and conformity to DIN 13, 6H ensures repeatable pass/fail inspection in production environments; order the gauge directly via Metav Werkzeuge or consult Metav’s specialists for application advice. Limit thread plug gauge M58 × 2 mm (right-hand) — Metav IndustryLine The limit thread plug gauge M58 × 2 mm (right-hand) is engineered for rapid conformity checks of metric ISO fine threads in production and inspection settings, offering a rugged, wear‑resistant solution for go/no‑go testing. Precision gauging to DIN 13, 6H Hardened gauge steel construction Right-hand M58 × 2 mm fine thread Stable 1.8 kg mass for repeatability Ensure interchangeability and avoid assembly faults The M58 × 2 mm limit plug gauge is designed to verify whether metric ISO fine threads fall within the specified tolerance class DIN 13, 6H. By providing a clear go/no‑go result, the device reduces the need for secondary measurements and lowers the risk of assembly failures. The limit plug gauge principle is straightforward: the go end confirms minimum material and form, while the no‑go end detects oversize or out‑of‑tolerance threads, enabling fast decisions on acceptance or rework and improving production throughput. Durable build for sustained repeatability Manufactured from hardened gauge steel, the gauge resists wear and maintains its profile over prolonged use; the substantial 1.8 kg mass adds stability during manual inspection and reduces the effect of operator handling. This mechanical robustness means fewer replacements and more consistent results across batches, supporting a cost‑effective quality routine. Regular visual inspection for burrs and light cleaning are usually sufficient maintenance; hardened steel avoids rapid degradation even under frequent use. Practical application in shop floor and quality labs As a right‑hand limit thread plug gauge, this instrument suits both workshop inspection stations and incoming part verification in a laboratory environment. The compact, single‑piece construction simplifies handling during repeated checks and integrates easily into pick‑and‑place test workflows or manual inspection benches. For complex requirements or automated lines, Metav Werkzeuge can advise on integration options and compatible fixture designs to ensure the gauge meets specific process needs. Choose the Metav IndustryLine M58 × 2 mm limit thread plug gauge for reliable pass/fail thread inspection — contact Metav Werkzeuge for technical advice and to arrange procurement. Technical data SKU: M315.058.7 GTIN: 4054469123578 Tariff code: 90173000 Facts Thread size: M58 × 2 mm Weight: 1.8 kg Standard: DIN 13, 6H Special features Material: hardened gauge steel Right-hand thread Category: limit thread plug gauge Brand: Metav IndustryLine FAQ What does the tolerance class DIN 13, 6H indicate? DIN 13, 6H specifies the thread tolerance and fit for metric internal threads; the limit thread plug gauge checks conformity to that class for reliable interchangeability. How is the limit plug gauge used for inspection? The go end of the limit plug gauge should enter the thread smoothly; the no‑go end must not fully engage if the thread is within tolerance. The M58 × 2 mm gauge provides a clear pass/fail indication for each tested thread. What material is the gauge made from and why? The gauge is made of hardened gauge steel, selected for wear resistance and dimensional stability to ensure long service life under repeated use. Is the M58 × 2 mm gauge suitable for production line checks? Yes, the limit plug gauge is intended for rapid production checks and incoming inspection, delivering fast go/no‑go results that reduce cycle downtime and rework. Can this gauge be used for non‑standard or left‑hand threads? This specific item is a right‑hand gauge for metric ISO fine threads; left‑hand or custom variants require a different gauge designed for that thread direction. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
M58x2 Thread Ring Gauge Right-Hand ISO Metric Fine Thread DIN 13, 6g, Hardened Gauge Steel - Metav IndustryLine
Reliable inspection of metric ISO fine threads is achieved through hardened gauge steel and compliance with DIN 13; choose the no‑go ring for clear rejection of out‑of‑tolerance parts. Order directly via Metav Werkzeuge or contact our consultants for application support. Thread ring gauge M58 x 2 mm – No‑go, DIN 13 (right‑hand) by Metav IndustryLine The Thread ring gauge M58 x 2 mm – No‑go is a hardened inspection ring for fast verification of right‑hand metric ISO fine threads in production and incoming inspection. Hardened gauge steel construction For metric ISO fine threads DIN 13 No‑go ring for clear rejection Ensure repeatable thread control on the shop floor The ring is manufactured in hardened gauge steel, which maintains form stability during repetitive use and resists wear that would otherwise compromise measurement reliability. Built to DIN 13, the gauge provides a verifiable reference against the standard used throughout metric thread production; this simplifies acceptance criteria and reduces ambiguity in quality decisions. Using a dedicated no‑go ring removes subjective judgement from inspection: a part that will not enter the ring is immediately identifiable as non‑conforming, which speeds sorting and prevents defective components proceeding through the process. Robust design that reduces handling uncertainty A compact, solid ring format minimises deformation under handling, so operators benefit from consistent tactile feedback and a low risk of false acceptances. The gauge's right‑hand orientation and M58 × 2 mm specification match the common metric fine‑threaded components found in assemblies and fixtures, allowing direct interchangeability in routine checks. The clear pass/fail function supports faster throughput and fewer secondary controls, contributing to overall process efficiency and reduced rework rates in production environments. Fits into standard quality workflows and inspection plans Integrating the ring into incoming inspection, first article inspection or in‑process checks is straightforward: the rigid geometry and standard norm reference make traceability and documentation simpler. The product is categorised for use with metric ISO fine threads and is suitable where a deterministic go/no‑go decision is required. For regulated production or audits, the defined DIN 13 basis assists in creating unambiguous inspection records and supports supplier acceptance protocols. The gauge is a practical tool for quality engineers seeking to tighten control without complex measuring equipment. Contact Metav Werkzeuge today to confirm suitability for specific thread forms or to request a quotation for Metav IndustryLine gauges including M315.258.7 Technical data Article number: M315.258.7 SKU: M315.258.7 GTIN: 4054469126906 Weight: 1.4 kg Tariff number: 90173000 Facts Thread size: M58 × 2 mm Standard: DIN 13 Hand: Right‑hand Special features Material: gauge steel, hardened Function: No‑go ring gauge for metric ISO fine thread Category: Gauges / Inspection rings FAQ What is the intended use of this ring gauge? The ring gauge is intended for go/no‑go inspection of right‑hand metric ISO fine threads, providing a definitive rejection criterion for M58 × 2 mm threads. Does the gauge conform to a recognised standard? Yes, the gauge is manufactured to DIN 13, which standardises dimensions and tolerances for metric threads. What material is the gauge made from and why is that important? The ring is made from hardened gauge steel, chosen for wear resistance and dimensional stability so that inspection results remain repeatable over many cycles. How does a no‑go ring improve inspection speed? A no‑go ring provides an immediate pass/fail outcome; parts that will not enter the ring are rejected without time‑consuming measurement, reducing inspection time per part. Is the product referenced by a manufacturer code? The Metav IndustryLine ring is listed under M315.258.7, which can be used when ordering or requesting technical details. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
Fast, tactile checks where electronics are impractical
Gauges and test pins provide unequivocal go/no-go results for threads, bores, gaps and radii without relying on electronics. The range covers plug gauges and ring gauges for internal and external threads, feeler gauges and precision feeler strips for micro‑gap assessment, plus probe pins and measuring pins for tactile diameter and pitch checks.
How these tools work in the production environment
Mechanical gauges operate as direct reference standards: a plug gauge or ring gauge verifies conformity to thread profiles and mating ability, while limit gauges separate accept from reject in a single step. Test pins are used to tactilely measure small bore diameters, centre‑to‑centre distances and radii. Manufactured from hardened gauge steel or ceramic and often precision lapped, these instruments deliver immediate physical results that are ideal for incoming inspection, machine‑side checks and final control.
Measurable benefits that affect production performance
- Reduced scrap and rework through rapid, unambiguous pass/fail assessment.
- Increased repeatability thanks to very low measurement uncertainty and fine lapping.
- Lower downtime: quick checks at the machine save cycle time and reduce setup periods.
- Durable construction with high wear resistance from specialised, low‑distortion alloys.
- Versatile delivery formats: individual gauges, organised sets in wooden cases or metre‑length feeler rolls compliant with DIN 2269.
Why Metav is the practical choice for precision supplies
Metav combines decades of expertise with a broad warehouse and quality filtering from Emmerich. As a precision partner for industry, craft and trade, Metav supplies a comprehensive selection of gauges and test pins alongside complementary tools such as precision calipers and setting rings. With over 48,000 customers and a catalogue exceeding 250,000 items, Metav is positioned to supply reliably, reduce vendor complexity and support traceable quality control to national standards.
Summary
Gauges and test pins are indispensable for dependable, repeatable quality assurance where tactile, mechanical verification is preferred. Choose these plug gauges, ring gauges, feeler strips and probe pins when immediate, robust measurement decisions are required on the shop floor.
FAQ
What materials are gauges and test pins typically made from?
Gauges and test pins are usually manufactured from hardened gauge steel for durability and wear resistance; ceramic variants are available where thermal stability and minimal wear are critical.
How do thread gauges ensure mating capability?
Thread plug gauges and ring gauges check flank diameters and thread form against standards, providing a clear go/no‑go verdict that confirms pairability with mating parts.
Which tolerance class should I choose for probe pins and gauge sets?
Select tolerance classes aligned with your inspection requirements; for high‑precision tasks, sets produced to DIN 2269 or equivalent tolerance classes ensure micrometre‑level control and repeatability.
Can feeler gauges measure contact gaps in valve and engine work reliably?
Yes. Feeler gauges and precision feeler strips, supplied either as a fan or metre‑length rolls, allow accurate assessment of valve clearances and contact gaps down to micrometre increments.
How do limit gauges speed up in‑process inspection?
Limit gauges separate good from bad in a single, tactile operation, enabling rapid go/no‑go checks at the machine and reducing both inspection time and the likelihood of human interpretation errors.
Fragen zu diesen Produkten??
Mit mehr als 30 Jahren Erfahrung beraten wir Sie gerne persönlich.
Tel.: +49 2822 7131930
Mail: info@metav-werkzeuge.com