Precision gauge blocks and plug gauges for reliable dimensional control
Mechanical gauge blocks and plug gauges are essential for tactile verification of threads, bores and gap dimensions, providing fast, unambiguous go/no-go results that enhance process reliability and reduce scrap. Designed for industrial metalworking and toolmaking, these precision tools support incoming inspection and final quality checks by delivering traceable measurements in applications such as thread inspection, bore diameter testing and spacing checks. Manufactured from specially hardened, low-distortion alloys and fine-lapped for minimal measurement uncertainty, the range includes thread plug gauges, precision plug gauges and calibration gauge blocks to ensure long-term repeatability and wear resistance.
10.6mm Test Pin 50mm Length Workshop Version, Special Steel - Metav IndustryLine
Benefit from the combination of high‑precision tolerance ±0.002 mm, robust special steel construction and a compact 50 mm length for reliable end‑measure checks; order the gauge pin directly via Metav Werkzeuge or consult our specialists for tailored application advice. Gauge pin, single – 10.6 mm diameter, 50 mm length (Metav IndustryLine) Gauge pin, single is a precision inspection pin engineered for end‑measure verification and fixture alignment in workshop and production environments High‑precision tolerance ±0.002 mm Diameter 10.6 mm with 50 mm length Made from special steel for workshop use Robust workshop version for daily inspection Precision that stabilises production control The gauge pin delivers ±0.002 mm accuracy in a compact form, enabling repeatable checks for components where end dimensions determine assembly fit. This level of precision supports tight process control and reduces the risk of rejects by providing a clear, objective reference during inline or batch inspections. In practical terms, the compact 50 mm length and 10.6 mm diameter make the pin suitable for small to medium‑sized bores and features, allowing technicians to verify final sizes quickly without elaborate set‑ups. Built for workshop durability and ease of handling Constructed from special steel and labelled as a workshop version, the inspection pin tolerates routine handling and retains measuring integrity under typical shop conditions. At approximately 0.1 kg the component is easy to position and manoeuvre in fixtures, while the single‑piece design simplifies inventory and replacement logistics. The straightforward geometry minimises the chance of setup error and shortens inspection cycles, delivering a tangible productivity benefit for quality control teams. Integrates simply into inspection routines and tooling The pin is intended for end‑measure verification, fixture alignment and use as a reference mandrel in gauging operations. Supplied as a single inspection pin, it complements existing gauge sets and can be used alongside comparators, go/no‑go fixtures or optical checks to confirm critical dimensions. For customers seeking reliable traceability or application advice, Metav Werkzeuge provides technical guidance to match the inspection pin to specific process requirements and measurement workflows. For dependable end‑measure verification choose the Metav IndustryLine gauge pin and contact Metav Werkzeuge in Emmerich for specification support and supply coordination Technical data Article number: M323.A60 GTIN: 4061905064715 Product name: Gauge pin, single, 10.6 mm diameter, 50 mm length Manufacturer: Metav IndustryLine Core specifications Diameter: 10.6 mm Length: 50 mm Tolerance: ±0.002 mm Weight: 0.1 kg Measurement range min: 10.6 mm Measurement range max: 10.6 mm Design & features Material: Special steel Version: Workshop execution Delivery: Single inspection pin Application: End‑measure verification FAQ What is the usable diameter and length of this inspection pin? The inspection pin has a diameter of 10.6 mm and a usable length of 50 mm, suitable for end‑measure checks and fixture alignment. What accuracy can be expected from this gauge pin? Manufactured to a tolerance of ±0.002 mm, the gauge pin provides high‑precision reference measurements for routine inspection tasks. Which material is used and is the pin suitable for workshop use? The pin is made from special steel and specified as a workshop version, designed to withstand daily handling in production environments. Is this pin supplied as a single item and how is it identified? Yes, the product is supplied as a single inspection pin and is identified as Article number M323.A60 with GTIN 4061905064715. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
10.71mm Gauge Pin, Single, 50mm Length, Workshop Version - Metav IndustryLine
Take advantage of accurate end‑dimension checks through the combination of 10.71 mm nominal diameter, a fine ±0.002 mm tolerance and a compact 50 mm length for reliable go/no‑go and fit verifications; order the gauge pin directly via Metav Werkzeuge or consult the team for application advice. Gauge pin M323.A71 — single test pin, 10.71 mm × 50 mm The Gauge pin M323.A71 is a workshop‑grade single test pin designed for precise end‑measure checks and repeatable fit verification in production and inspection environments. Workshop‑grade construction for daily use Diameter 10.71 mm with ±0.002 mm tolerance 50 mm usable length for end‑measure checks Made from special steel for durable wear resistance Improve production control with high repeatability The compact test pin delivers a measurable improvement in inspection consistency: with a nominal diameter of 10.71 mm and a documented ±0.002 mm tolerance, the component supports reliable go/no‑go evaluations and fine clearance checks. This level of precision reduces uncertainties during assembly trials and helps to lower scrap rates by catching out‑of‑tolerance conditions early. The specification is expressed in clear numerical terms so purchasing and quality teams can compare it directly against drawing tolerances and inspection plans. Built for workshop use and long service life Constructed as a workshop‑grade tool from special steel, the pin withstands repeated seating and withdrawal in fixtures and gauges. The 50 mm overall length provides sufficient engagement for secure measurements while remaining easy to handle in busy production areas; the modest mass supports quick manoeuvring and minimal operator fatigue. Material selection focuses on wear resistance and dimensional stability, which preserves the pin’s calibrated condition over many cycles and reduces the need for frequent replacement. Easy to integrate into existing inspection routines The pin is suitable for routine end‑dimension checks, in‑fixture validation and comparator use, complementing both manual and semi‑automated quality workflows. Traceable identification via the product code ensures clear record keeping for inventory and inspection logs, while the compact format fits standard pin holders and gauge blocks. By adding this precision component to a control plan, teams gain a simple, quantifiable tool that supports process capability assessments and helps maintain consistent product quality. Choose the Metav IndustryLine M323.A71 for dependable end‑measure checks and contact Metav Werkzeuge in Emmerich for procurement guidance and timely supply. Technical data Article number: M323.A71 GTIN: 4061905065514 Manufacturer: Metav IndustryLine Facts Diameter: 10.71 mm Length: 50 mm Tolerance: ±0.002 mm Weight: 0.1 kg Special features Material: special steel Workshop version Category: gauge pin / test pin Accuracy grade suitable for fine fit and end‑measure checks FAQ What inspection tasks is this pin suitable for? The M323.A71 gauge pin is intended for end‑dimension checks, fit verification and go/no‑go evaluations in workshop and production settings. Is the M323.A71 compatible with standard pin holders and fixtures? Yes, the single test pin is designed to fit common holders and comparator fixtures used for plug‑type checks. What does the ±0.002 mm specification mean for daily use? A tolerance of ±0.002 mm indicates the allowable deviation from the nominal 10.71 mm diameter and supports high repeatability for fine clearance and assembly verification. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
10.72mm Gauge Pin Single 50mm Length Workshop Finish - Metav IndustryLine
Compact, workshop-ready gauge pin that pairs repeatable measurement with a fine ±0.002 mm tolerance and a robust special‑steel construction; ideal for routine end‑size checks and fixture inspections. Order the component directly via Metav Werkzeuge or consult their product specialists for integration into existing gauge sets. M323.A72 — Gauge pin (10.72 mm Ø, 50 mm length) by Metav IndustryLine M323.A72 is a single gauge pin designed for precise end‑size verification and confined inspection tasks in workshop environments. Workshop‑grade construction Diameter 10.72 mm precision Length 50 mm compact checks Tolerance ±0.002 mm accuracy Reliable precision for routine verification Manufactured for consistent results, this gauge pin delivers a measured diameter of 10.72 mm with an indicated variation of ±0.002 mm, making it suitable for fine verification tasks where reproducibility matters. Classified in the micro range for measuring tools (10–100 mm), the component combines short overall length with stable geometry to reduce measurement uncertainty during frequent use. The stated tolerance supports quality control processes that demand clear pass/fail criteria without over‑specifying equipment capability. Durable build for workshop environments The measuring pin is produced from special steel, specified to provide dimensional stability under regular handling. The workshop version is intended for daily use in production and maintenance settings where tools are subject to frequent insertion and removal. Its modest mass contributes to easy handling while retaining sufficient rigidity for repeatable end‑face contact checks. The construction focuses on practical longevity rather than claiming specific surface treatments or heat‑treatment grades beyond the stated material. Compact dimensions for confined checks and fixtures With a 50 mm overall length and a compact diameter, this inspection pin fits into tight bores and assembly jigs where larger gauges would be impractical. Compact format facilitates quick in‑process checks and can be mounted in holders or test fixtures for comparative or go/no‑go inspections. The small footprint supports ergonomic handling during batch inspections and reduces the risk of interference in complex assemblies. Integrates easily into existing verification workflows Designed as a single, stand‑alone gauge pin, the unit is compatible with common workshop fixtures and gauge sets used for end‑size confirmation. The clear specification data—diameter, length and tolerance—allows straightforward incorporation into inspection plans and measurement logs. For traceability, the item is listed under SKU M323.A72 and can be referenced in quality documentation or parts lists to ensure consistent procurement and replacement. Discuss Metav IndustryLine gauge pin options with Metav Werkzeuge to confirm fitment and to arrange supply tailored to inspection routines. Technical data Article number: M323.A72 GTIN: 4061905066184 Label: Test pin, single, 10.72 mm diameter, 50 mm length Numbers / Core technical data Diameter: 10.72 mm Length: 50 mm Mass: 0.10 kg Accuracy/variation: ±0.002 mm Special features / Materials Material: Special steel Version: Workshop execution Category: Gauge pins (Messstifte) Application: End‑size checks FAQ What are the exact dimensions of the pin? The pin measures 10.72 mm in diameter with a total length of 50 mm; it is listed as SKU M323.A72. What accuracy can be expected during checks? The specified variation is ±0.002 mm, which supports precise go/no‑go and comparative measurements in routine inspection tasks. Which material is used for this gauge pin? The component is made from special steel, provided for dimensional stability appropriate to workshop use. Is this pin suitable for fixture mounting and jigs? Yes, the compact 50 mm length and standard cylindrical geometry make it suitable for mounting in common fixtures and gauge holders used for end‑size verification. Can this item be referenced in quality documentation? The SKU M323.A72 and GTIN 4061905066184 allow unambiguous identification for procurement and quality records. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
10.73mm Gauge Pin, Single, 50mm Length, Workshop Version - Metav IndustryLine
Precision-ground construction and a tight ±0.002 mm tolerance make this single gauge pin a reliable reference for end-dimension checks; combined with its compact 10.73 mm diameter and 50 mm length, the component supports repeatable measurements in fine mechanical setups. Order directly via Metav Werkzeuge or request technical advice from our specialists to ensure seamless integration into existing inspection routines. Gauge pin, single — 10.73 mm diameter, 50 mm length (Metav IndustryLine) Gauge pin, single — 10.73 mm diameter, 50 mm length is a compact, workshop-grade reference pin intended for precise end-dimension inspection and fixture checks. Precision ground Ø 10.73 mm Length 50 mm for compact reference Tight tolerance ±0.002 mm Workshop-grade special steel construction Engineered for repeatable reference measurements The component is precision-ground to deliver a repeatable datum for end-stop and go/no-go fixtures. With a declared accuracy of ±0.002 mm, the pin supports tight control limits in production checks and quality assurance procedures, reducing uncertainty during frequent measurements. The combination of geometric stability and minimal surface deviation helps to shorten inspection cycles by providing an immediate, verifiable reference without additional alignment steps. Compact dimensions that suit fine mechanical work Placed in the micro measurement category, the pin’s 10.73 mm diameter and 50 mm length are tailored to fine mechanical and toolroom applications where space is limited but precision remains critical. The compact form factor preserves stiffness while allowing easy handling in jigs, gauges and small-bore checks. For workshops and small-series production, the size offers the best compromise between reach and rigidity, enabling rapid insertion and removal during assembly or verification tasks. Robust material and workshop design for daily use Manufactured from special steel with a workshop-focused finish, the pin withstands repetitive use in demanding environments. The workshop-grade execution emphasises durability and serviceability, making it suitable for frequent contact with hardened seats and gauge bodies. As an individual test pin, it functions as a reliable end dimension reference within inspection benches and fixture setups, helping to maintain consistent part quality across production batches. Contact Metav Werkzeuge in Emmerich to discuss how the Metav IndustryLine gauge pin (SKU M323.A73) can be specified for inspection jigs or to request a tailored quotation — eMail: info@metav-werkzeuge.com • Tel: +49 2822 7131930 Technical Data Article number: M323.A73 GTIN: 4061905066580 Label: Prüfstift, einzeln, 10,73 mm Länge 50 mm Brand: Metav IndustryLine Numbers Diameter: 10.73 mm Length: 50 mm Tolerance: ±0.002 mm Weight: 0.1 kg Special features Workshop version Material: Special steel Single test pin (individual delivery) Intended use: end-dimension reference FAQ What tolerance does this gauge pin offer? The gauge pin delivers a declared tolerance of ±0.002 mm, specified for the Metav IndustryLine gauge pin (SKU M323.A73) to ensure tight control in inspection routines. Is the pin suitable for fixture and jig reference points? Yes. The pin’s precision-ground surface and compact 10.73 mm × 50 mm format make it suitable as a reference in jigs, gauges and small-bore fixtures. Which material is used for this test pin? The Metav IndustryLine test pin is produced from special steel, chosen for wear resistance and stability under frequent contact. Can this pin be used for end-dimension verification in small-series production? Absolutely. Its compact size and tight tolerance are designed for repeatable end-dimension checks in fine mechanical and small-batch production environments. What is the intended application described by 'endmasse'? The storytrigger 'endmasse' refers to its role as an end-dimension reference pin used for final size checks and go/no-go validation in inspection setups. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
10.74mm Gauge Pin, Single, 50mm Length Workshop Version - Metav IndustryLine
Take advantage of precise end‑measure control, robust workshop design and a compact 50 mm length for seamless inspection workflows; the combination of Ø 10.74 mm diameter, ±0.002 mm accuracy and special steel construction ensures dependable reference measurements — order directly via Metav Werkzeuge or consult our specialists for application advice. Test pin M323.A74 — Test pin, Ø 10.74 mm, 50 mm length (Metav IndustryLine) Test pin M323.A74 for end‑measure checks and fixture alignment in inspection and assembly applications Workshop version for daily shopfloor use Diameter 10.74 mm for exact end dimensions Accuracy ±0.002 mm for repeatable reference measurements Special steel construction for durability and wear resistance Consistent reference precision for inspection tasks The M323.A74 test pin is engineered as a compact reference element for end‑measurement and alignment operations. With a nominal diameter of 10.74 mm and a measured length of 50 mm, the pin supplies a stable contact geometry that reduces variation when checking final dimensions. The specified ±0.002 mm accuracy provides a tangible improvement in repeatability compared with general inspection probes, supporting tighter control limits and more reliable pass/fail decisions. Built-in dimensional stability from the special steel material minimises wear over repeated cycles, extending useful service life. Robust workshop design that keeps processes moving Designed as a workshop version, this test pin tolerates routine handling and integration into fixtures and test benches. The moderate mass (approx. 0.1 kg) and compact 50 mm length make it easy to position while maintaining the rigidity required for consistent contact. Supplied as a single item in a protective transport box, the component arrives ready for secure storage and immediate use, which reduces setup time and prevents damage in transit. This practical approach to design supports continuous production and lowers the frequency of replacement. Practical integration into quality workflows The cylindrical contact geometry and exact diameter make the pin suitable for end‑gauging, alignment checks and fixture setting in small to medium assemblies. Its straightforward form factor simplifies fixture design and inspection routines, so the element can be used as a fixed reference or an interchangeable gauge insert. Metav IndustryLine's quality assurance ensures consistent batch conformity from stock in Emmerich, helping to maintain supply security for routine inspection tools. For specialised applications, Metav's product experts can advise on fitment and usage scenarios to match process requirements. Contact Metav Werkzeuge for purchase or application advice and order the Metav IndustryLine test pin (Ø 10.74 mm, 50 mm) directly from our Emmerich stock Technical data SKU: M323.A74 GTIN: 4061905066597 Label: Test pin, single, 10.74 mm length 50 mm Category: Test pins (Messstifte) Facts Diameter: 10.74 mm Length: 50 mm Accuracy: ±0.002 mm Weight: 0.1 kg Measurement range (max): 10.74 mm Special features Material: special steel Workshop version Supplied single item Delivered in protective transport box FAQ What tolerance can be expected from this test pin? The M323.A74 test pin is specified with an accuracy of ±0.002 mm, offering high repeatability for end‑measure checks in workshop environments. Is the pin suitable for fixture alignment in assembly jigs? Yes, the test pin’s compact 50 mm length and precise 10.74 mm diameter make it well suited as a reference element for fixture alignment and setting tasks. In what condition is the pin supplied? The Metav IndustryLine test pin is supplied as a single item, securely packed in a protective transport box to prevent damage during storage and transport. Can this test pin be used for repeated contact measurements without rapid wear? Constructed from special steel, the pin offers improved wear resistance for repeated contact cycles; proper handling and storage further extend service life. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
10.75mm Gauge Pin, Single, 50mm Length, Workshop Version - Metav IndustryLine
Take advantage of the combination of ±0.002 mm repeatability, special steel construction and a compact 50 mm shaft for reliable end‑dimension control in precision workshops — delivered in a protective transport case for safe handling. Order the gage pin directly via Metav Werkzeuge or ask our consultants if needed. Gage pin M323.A75 — test pin, Ø 10.75 mm, 50 mm length (Metav IndustryLine) The gage pin M323.A75 is a compact, workshop‑grade test pin for precise end‑dimension verification and fixture checks High repeatability ±0.002 mm Special steel for wear resistance 50 mm shaft length for stable handling Supplied in protective transport case Precision where small tolerances matter This compact test pin is built for applications that demand consistent, measurable results: with a declared tolerance of ±0.002 mm, the component provides very fine reproducibility for go/no‑go checks, plug gauges and fixture verification. The combination of a short 50 mm shaft and special steel reduces flex and wear during repetitive measurements, which translates into fewer re‑checks and higher throughput on inspection benches. Such a level of accuracy supports tight quality routines in small series production and fine mechanical assembly. Designed for fine mechanical and workshop use Classified in the micro measurement range (10–100 mm), the pin is optimised for end‑dimension control of small components and mating parts. The workshop version construction makes it robust for daily use while remaining easy to position in jigs and fixtures. Supplied in a protective case, the test pin stays transport‑safe and prepared for use on the shop floor — a practical choice where handling and storage affect long‑term traceability and component condition. Practical handling and compatibility with inspection routines The modest weight (0.1 kg) and compact geometry enable straightforward manual deployment in measurement sequences and simple fixture applications. The design supports rapid visual and tactile checks and integrates well into tactile gaging systems or comparative inspection benches. Where reproducible end‑measurements are required, this gage pin offers a durable, low‑maintenance solution that reduces process variation and supports consistent quality documentation. Consult Metav Werkzeuge for specification matching and to confirm suitability for intended inspection tasks — our team can advise on integration and supply Technical data Article number: M323.A75 GTIN: 4061905062926 Brand: Metav IndustryLine Facts Diameter: 10.75 mm Length: 50 mm Measuring range: 10.75 mm Accuracy: ±0.002 mm Weight: 0.1 kg Special features Workshop execution Protective transport case included Material: special steel Category: test pins / gage pins FAQ What tolerance can be expected from this test pin? The gage pin M323.A75 is specified with a tolerance of ±0.002 mm, making it suitable for fine inspection tasks where very small deviations must be detected. Which material is used for the pin? This test pin is manufactured from special steel, chosen for wear resistance and durability in repetitive measurement cycles. Is the pin supplied ready for use in the workshop? Yes, the item is delivered in a protective transport case and presented as a workshop version to withstand daily handling on inspection benches. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
10.76mm Test Pin Length 50mm Workshop Version - Metav IndustryLine
Take advantage of the combination of high dimensional accuracy ±0.002 mm, robust special steel construction and a protective transport case for dependable workshop inspection routines; order directly via Metav Werkzeuge or ask the consultants for application advice. Test pin, single, 10.76 mm Ø, 50 mm length — Metav IndustryLine The test pin, single, 10.76 mm Ø, 50 mm length is a compact end-gauge for precise dimensional checks in workshop inspection and end-measurement tasks. High dimensional accuracy ±0.002 mm Special steel for robust service Workshop execution with durable finish Delivered in a protective transport case Reliable precision for end-measurement checks This compact inspection aid offers ±0.002 mm repeatability, making it suitable for demanding workshop control where small tolerance deviations matter. Classified in the micro range (max measuring span 10–100 mm), this design prioritises stiffness and stability in a short format, which reduces bending and operator-induced error during short-span checks. The defined diameter of 10.76 mm is intended for direct verification of bore or pin fits and provides a clear, measurable reference for go/no-go assessments or fixture set-ups. The measured tolerance figure is a practical indicator of expected variation under normal workshop use and supports faster decision-making on the shop floor. Robust construction and practical handling Constructed from special steel, the device resists wear and maintains a consistent gauge surface even under frequent use. The 50 mm overall length balances reach with ease of handling; at 0.1 kg the component is light enough for single-handed use yet sufficiently massed to sit stably in comparison fixtures. The workshop execution indicates a finish and hardening process tailored for everyday industrial environments rather than delicate laboratory conditions. Delivery in a protective transport case safeguards the pin during storage and transport, reducing the risk of accidental damage and preserving measurement integrity across shifts. Integration into inspection routines and compatibility Designed as an end-measurement stub for visual and mechanical checks, the pin functions well with comparator stands, gauge blocks and bench fixtures to speed up routine verification. The simple geometry minimises fixturing complexity and enables reproducible seating in bores and gauges. By using a standardised diameter and overall length, the component fits established inspection workflows and reduces set-up times, contributing to improved throughput and lower risk of rejected parts due to measurement uncertainty. The product is supplied under the Metav IndustryLine range and is identified by SKU M323.A76 for ordering and inventory purposes. Contact Metav Werkzeuge to secure the Metav IndustryLine test pin M323.A76 with ±0.002 mm accuracy and a protective transport case for reliable workshop inspection support Technical data Article number: M323.A76 GTIN: 4061905062933 Manufacturer: Metav IndustryLine Facts Diameter: 10.76 mm Overall length: 50 mm Accuracy / tolerance: ±0.002 mm Weight: 0.1 kg Special features Material: Special steel Workshop execution Delivered in protective transport case FAQ Is this test pin suitable for precision bore checks? Yes. The test pin is intended for bore and fit verifications where a fixed diameter reference of 10.76 mm and an accuracy of ±0.002 mm are required. Can the pin be used in standard comparator stands? Yes. The simple cylindrical geometry and 50 mm length make the pin compatible with common comparator fixtures and gauge holders. What does "workshop execution" mean for durability? Workshop execution denotes a finish and treatment aimed at daily industrial use; the special steel provides enhanced wear resistance for routine inspection tasks. Is the test pin supplied with a certificate of calibration? The product is supplied as described; no calibration certificate is included unless explicitly specified in the product label or order data. Which SKU should be referenced when ordering spare test pins? Refer to SKU M323.A76 when ordering or enquiring to ensure the correct diameter and length are delivered. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
10.77mm Gauge Pin Length 50mm Workshop Finish, Special Steel - Metav IndustryLine
Take advantage of a compact inspection solution that combines high repeatability (±0.002 mm), a defined diameter of 10.77 mm, and a robust 50 mm length for reliable end‑measure checks; order this precision gage pin directly via Metav Werkzeuge or consult our specialists for application advice. Test pin (single) — 10.77 mm Ø, 50 mm length by Metav IndustryLine A single test pin designed for precise end‑measurement and inspection tasks in workshop and production environments. Workshop-grade design for regular use High-precision tolerance ±0.002 mm Fixed Ø 10.77 mm, length 50 mm Made from special steel for durability Precision that keeps production moving This inspection pin delivers consistently repeatable results thanks to its ±0.002 mm tolerance, which is suitable for fine inspection tasks where small deviations matter. The defined diameter of 10.77 mm and 50 mm length provide a stable reference for end‑dimension checks and go/no‑go comparisons. The tight tolerance reduces rework and supports traceable inspection routines, contributing to shorter inspection cycles and fewer production interruptions. Robust workshop design for everyday inspection Manufactured in a workshop version, this pin is built to withstand regular handling in industrial settings. The body is produced from special steel, offering resistance to wear and deformation while remaining compact and easy to use. At approximately 0.1 kg, the pin is light enough for manual positioning yet rigid enough to avoid flexing during typical end‑measure operations. The design balances durability with practical handling for quality control staff. Clear role in quality assurance workflows As a fixed-size inspection element, the pin simplifies fixture setups, alignment tasks and end‑face verification. Its defined geometry makes it a straightforward reference for comparative gauging and routine quality checks, improving throughput in inspection benches and assembly stations. Where reproducibility is needed, the stable dimensions and material choice help maintain measurement integrity over repeated cycles. For application-specific advice or to secure Metav IndustryLine inspection components for production use, contact Metav Werkzeuge — info@metav-werkzeuge.com or call +49 2822 7131930 for expert guidance and supply options Technical data SKU: M323.A77 GTIN: 4061905062940 Manufacturer: Metav IndustryLine Facts Diameter: 10.77 mm Length: 50 mm Tolerance: ±0.002 mm Weight: 0.1 kg Special features Material: special steel Workshop version Category: Messstifte Label: Prüfstift, einzeln, 10,77 mm Länge 50 mm FAQ What is the intended use of this inspection pin? The test pin is intended for end‑measure checks and comparative gauging in workshop and production inspection tasks; the fixed Ø 10.77 mm and 50 mm length make it a reliable reference for such applications. How precise is the diameter specification? The inspection pin is manufactured to a tolerance of ±0.002 mm, which supports high repeatability for dimensional checks. Which material is used for the pin? The component is made from special steel, chosen to provide wear resistance and dimensional stability during regular inspection use. Can this pin be used in fixture and alignment setups? Yes; the fixed geometry and robust design allow straightforward integration into fixtures for alignment, go/no‑go checks and reference measurements. Is a calibration certificate supplied with the pin? A standard calibration applies; no ISO 17025 certificate is specified for this item in the available data. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
10.78mm Gauge Pin, 50mm Length, Workshop Version, Special Steel, Supplied in Case - Metav IndustryLine
The combination of high workshop durability, ±0.002 mm manufacturing tolerance and a compact Ø 10.78 mm / 50 mm form factor delivers reliable end‑measurement results and reproducible fits in routine inspection tasks. Order this single gauge pin directly via Metav Werkzeuge or consult our specialists for application advice. Gauge pin M323.A78 — single gauge pin, Ø 10.78 mm, length 50 mm (Metav IndustryLine) A single gauge pin for workshop end‑measure checks and fit verification, specified at 10.78 mm diameter with a 50 mm overall length. Workshop‑grade precision ±0.002 mm Special steel for enhanced wear resistance Ø 10.78 mm, length 50 mm Single‑piece design for consistent end‑measure checks Reliable precision for everyday inspection tasks A compact inspection pin with ±0.002 mm manufacturing tolerance provides a reproducible reference for end‑measure and go/no‑go checks in production and maintenance environments. The fine tolerance means that clearance and interference fits can be verified with confidence, reducing the need for repeated rework and minimising stoppages. The small footprint of the pin supports tight access and makes it suitable for use in measuring fixtures, assembly jigs and quick verification stations. Built for workshop endurance and easy handling Machined from special steel, this workshop version is designed to resist wear during repeated insertions and withdrawals. The solid single‑piece construction offers dimensional stability and simplifies handling during rapid checks; the modest weight (0.1 kg) and standard length allow convenient mounting in fixture blocks or storage racks. Where repetitive checking is required, the durable surface finish helps maintain consistent contact conditions, which supports repeatable results across shifts and operators. Practical integration into quality procedures Supplied as an individual inspection pin, the item is ideal for end‑dimension control, seating tests and gauge stacks in standard metrology workflows. The clear nominal diameter of 10.78 mm and the concise physical specification facilitate traceability in inventory and work instructions; the product is listed under SKU M323.A78 for straightforward procurement and stock management. For precision control loops and assembly verification, the pin acts as a fast, deterministic reference that complements calipers and micrometres without replacing their broader measuring functions. Contact Metav Werkzeuge in Emmerich to confirm availability of the Metav IndustryLine gauge pin (M323.A78) and to discuss its fit for intended inspection setups Technical Data SKU: M323.A78 GTIN: 4061905062957 Eclass: 21170231 Brand: Metav IndustryLine Facts Diameter: 10.78 mm Length: 50 mm Tolerance: ±0.002 mm Weight: 0.1 kg Special features Material: Special steel Workshop version Single gauge pin for end‑measure checks Compact form for fixture integration FAQ What inspection tasks is this pin intended for? The gauge pin (Metav IndustryLine, SKU M323.A78) is intended for end‑dimension checks, seating tests and quick fit verification in workshop and production settings. Is the diameter tolerance suitable for precision fits? Yes. The ±0.002 mm tolerance of the Metav IndustryLine gauge pin supports reproducible checks for clearance and interference fits within typical workshop inspection limits. What material is used and how does it affect durability? The pin is manufactured from special steel, which gives the Metav IndustryLine gauge pin improved wear resistance and consistent surface contact over many cycles. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
10.79mm Gauge Pin, Single, 50mm Length, Workshop Version - Metav IndustryLine
Take advantage of a compact, workshop‑grade test solution that combines a diameter of 10.79 mm, a tight accuracy of ±0.002 mm and a sturdy 50 mm length for repeatable end‑measure checks; order the gauge pin directly via Metav Werkzeuge or consult the Metav advisers for batch supply and compatibility advice. Gauge pin M323.A79 — single test pin, Ø 10.79 mm, 50 mm length (Metav IndustryLine) The gauge pin M323.A79 is a single, hardened test pin designed for precise end‑measure verification and fit checks in machining and inspection environments, presented as a workshop‑grade tool for rapid repeat checks and simple handling. Workshop version, robust design Diameter 10.79 mm with ±0.002 mm accuracy Single pin, 50 mm length Precision where it counts for repeatable checks Built for measurement tasks that demand small tolerances, this gauge pin offers a diameter of 10.79 mm with an indicated accuracy of ±0.002 mm, which ensures consistent results when used for go/no‑go fitting, end‑measure verification or reference checks. The tight deviation limit translates into fewer remeasurements and more reliable pass/fail decisions on the shop floor. The hardened construction from special steel provides wear resistance so that dimensional stability is maintained across repeated cycles, reducing downtime for replacement and supporting steady inspection throughput. Designed for workshop use and reliable handling As a workshop version, the test pin is engineered for everyday use in busy production or maintenance settings. Its 50 mm overall length and compact mass make it easy to position in jigs, gauges or manual fixtures, while the solid construction withstands routine handling. The single‑piece design simplifies storage and retrieval, supporting a lean inspection workflow: quick checks can be performed without complex setup, helping to shorten process times and keep production moving. Protective transport packaging is provided to preserve the surface and geometry during logistics and storage. Practical benefits for quality control routines Integration into existing inspection routines is straightforward: the pin serves as a verified reference for dimensional comparison and helps to speed up incoming inspection, in‑process checks and final acceptance tests. Using a hardened gauge pin with a defined tolerance reduces measurement uncertainty and supports documented quality records. The compact form factor also facilitates mobile inspection tasks, making this tool suitable where space is limited or portability is required. For procurement and inventory planning, the clear SKU and GTIN identification aid traceability and stock management in industrial environments. For batch supply, availability checks and technical enquiries about the M323.A79 gauge pin, contact Metav Werkzeuge in Emmerich to discuss delivery options and suitable quantities for production use. Technical data Article number: M323.A79 Label: Gauge pin, single, 10.79 mm, length 50 mm GTIN: 4061905063596 Facts Diameter: 10.79 mm Length: 50 mm Weight: 0.1 kg Accuracy (deviation): ±0.002 mm ECLASS: 21170231 Special features Material: special steel Workshop version Delivered in a transport box FAQ What applications is this gauge pin suitable for? The M323.A79 gauge pin is suitable for end‑measure checks, fit verification and routine go/no‑go comparisons in machining and inspection tasks. How precise is the test pin and what does the tolerance mean? The test pin has an accuracy of ±0.002 mm, meaning dimensional deviation is tightly controlled to support repeatable, high‑precision checks during quality control. Is the pin durable enough for repeated shop‑floor use? Made from special steel and supplied as a workshop version, the pin is designed for repeated handling and wear resistance in production and maintenance environments. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
10.81mm Gauge Pin, Single, 50mm Length Workshop Version - Metav IndustryLine
Take advantage of the combination of workshop-grade construction, compact dimensions and ±0.002 mm repeatability for reliable end‑size checks in small bores; order directly via Metav Werkzeuge or consult our specialists for application advice. Test pin M323.A81 – gauge pin, 10.81 mm diameter, 50 mm length (Metav IndustryLine) A precision single gauge pin designed for end‑size verification and workshop inspection tasks, offering high repeatability in compact assemblies. Workshop-grade construction Diameter 10.81 mm, tight tolerance Length 50 mm for compact checks Tolerance ±0.002 mm Delivered in transport case Compact precision for small‑bore inspection The gauge pin is built for precise end‑size checking in confined spaces and small bores. Classified in the micro range for measuring tools (10–100 mm), its 10.81 mm diameter and 50 mm length combine to deliver a stable feel with minimal deflection during manual handling. The declared ±0.002 mm tolerance places this pin in a high‑precision class suitable for workshop inspection points where reproducible, measurable results matter. The special steel construction contributes to wear resistance and dimensional stability under normal workshop conditions. Practical benefits on the shop floor Designed as a workshop version, the pin supports fast go/no‑go gauging and assembly checks without complex fixturing. Its compact length and low mass enable quick insertion and removal, reducing cycle time for repetitive inspections while preserving accuracy. The delivery in a dedicated transport case protects the gauge during storage and transit, helping to maintain calibration and surface quality. Where traceable results are required, the robust tolerance specification simplifies documentation and acceptance criteria in quality protocols. Handling, longevity and integration Handling is straightforward: the pin’s geometry suits manual use and integration into simple fixtures or check plates. Constructed from special steel, it offers a balance between hardness and toughness for everyday workshop use. The light weight and compact profile make it easy to keep a set at the bench for immediate checks, reducing process interruptions. As part of the Metav IndustryLine, the component complements broader inspection toolsets and can be specified alongside other precision accessories for a consistent inspection strategy. For precise end‑size verification in small bores, request the Metav IndustryLine test pin M323.A81 from Metav Werkzeuge or contact our specialists at info@metav-werkzeuge.com to confirm suitability and delivery options Technical data Article number: M323.A81 GTIN: 4061905063619 SKU: M323.A81 Facts Diameter: 10.81 mm Length: 50 mm Weight: 0.1 kg Tolerance: ±0.002 mm Special features Material: Special steel Workshop design Delivered in transport case Category: Gauge pins (Messstifte) FAQ What is this test pin used for? This gauge pin is used for end‑size checking and small‑bore verification; the Metav IndustryLine test pin M323.A81 provides a compact reference diameter for inspection and assembly checks. Is the tolerance suitable for workshop quality control? Yes, the ±0.002 mm tolerance positions the pin for high‑precision workshop inspection where tight repeatability is required. Can the pin be stored with other gauges without risk of damage? The pin is supplied in a transport case to protect the surface and maintain dimensional integrity during storage and transport. Which materials is the pin made from? The pin is manufactured from special steel, chosen for its dimensional stability and wear resistance in typical workshop environments. Does this pin fit into standard check plates and fixtures? The 10.81 mm diameter and 50 mm length make it compatible with common small‑bore fixtures and handheld inspection tasks; consult Metav Werkzeuge for specific fixture integration advice. Metav IndustryLine: Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
10.82mm Gauge Pin Single 50mm Length Workshop Version - Metav IndustryLine
Take advantage of the combination of workshop-grade durability, tight tolerance of ±0.002 mm and the convenience of a protective transport case for reliable end‑dimension checks. Order the gauge pin directly via Metav Werkzeuge or consult our advisors for specification support. Gauge pin M323.A82 — 10.82 mm diameter, 50 mm length (Metav IndustryLine) The Gauge pin M323.A82 is a workshop-grade precision test pin designed for end‑dimension checks and fit verification in production and inspection tasks Workshop-grade construction Diameter 10.82 mm precision Tolerance ±0.002 mm Supplied in a protective case Faster inspection through dependable precision The gauge pin delivers consistent dimensional accuracy with a diameter of 10.82 mm and a stated tolerance of ±0.002 mm, enabling repeatable pass/fail checks on bores, dowel fits and assembly seats. As a single‑piece test pin made from special steel, it resists wear during frequent use; this reliability reduces rework and shortens inspection cycles, which translates directly into improved throughput and predictable quality control results. Built for workshop environments and everyday handling A 50 mm length and a compact design make the pin easy to handle at the bench or on a shop floor. The workshop-grade execution ensures robustness under routine handling, while the moderate mass supports stable seating during measurement tasks. Supplied in a protective case, the pin arrives ready for safe storage and transport, limiting damage and preserving the critical gauge diameter between uses. Practical fit verification and simple measurement logic As a straightforward test pin, the component is best used for go/no‑go style checks, trial fits and comparative gauging where basic functional verification is required rather than full dimensional reporting. The tight tolerance supports confident decisions in assembly and inspection steps and complements calipers or bore gauges when rapid throughput is a priority. For traceable inspection chains, the pin’s precise specification can be recorded alongside batch or job documentation. Selection and compatibility considerations The pin’s special steel construction offers a balance of hardness and machinability suited to general mechanical parts; it is intended for contact checks rather than abrasive applications. Its single‑piece format means minimal set‑up and immediate usability in repetitive tasks; matching the pin diameter to component bore class is the main selection criterion to ensure meaningful inspection results. Contact Metav Werkzeuge in Emmerich for expert advice on using the M323.A82 gauge pin in production workflows — email info@metav-werkzeuge.com or call +49 2822 7131930 for proximity support and ordering from our European stock. Technical data Article number: M323.A82 GTIN: 4061905063626 Manufacturer: Metav IndustryLine Diameter: 10.82 mm Length: 50 mm Tolerance / accuracy: ±0.002 mm Weight: 0.1 kg Material: Special steel Version: Workshop execution (single piece) Delivery: Supplied in a protective case Category: Gauge pin FAQ Is the gauge pin suitable for routine go/no‑go checks on bores? The M323.A82 gauge pin from Metav IndustryLine is intended for go/no‑go and fit verification on compatible bores and assembly seats, offering a clear pass/fail criterion thanks to its defined diameter and tight tolerance. Can the pin be used in abrasive or high‑temperature environments? The test pin is made from special steel and is designed for general workshop use; prolonged exposure to abrasive media or elevated temperatures may affect longevity, so application conditions should be matched to the material properties. How should the gauge pin be stored to preserve accuracy? Store the pin in its supplied protective case after cleaning and dry storage; this preserves the 10.82 mm diameter and prevents knocks or corrosion that could compromise measurement reliability. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
10.83mm Gauge Pin, Single, 50mm Length Workshop Version - Metav IndustryLine
Take advantage of the combination of tight tolerance, compact length and robust construction to streamline routine end‑dimension checks. The 10.83 mm diameter and ±0.002 mm accuracy ensure reliable repeatability in workshop inspection. Order the gauge pin directly via Metav Werkzeuge or consult our specialists if specification advice is required. Gauge pin M323.A83 — 10.83 mm diameter, 50 mm length (Metav IndustryLine) The gauge pin M323.A83 is a workshop‑grade precision test pin designed for end‑dimension verification and component fit checks in production and inspection environments. Workshop‑grade precision test pin Diameter 10.83 mm for end‑dimension checks Length 50 mm for fixture compatibility Tolerance ±0.002 mm for fine inspection Consistent measurement performance that speeds inspection This precision test pin delivers repeatable measurement results through its tight manufacturing tolerance of ±0.002 mm, which reduces sorting and rework. Where small deviations matter, the narrow diameter of 10.83 mm and the compact 50 mm length allow straightforward insertion into bores, gauges and assembly jigs, enabling fast go/no‑go assessments and consistent process control. The dimensional certainty shortens inspection loops and supports efficient quality decisions on the shop floor. Robust construction for regular workshop use Manufactured from special steel, the pin is built to withstand frequent handling typical of workshop routines while maintaining its dimensional stability. The workshop‑grade execution means the component pairs well with standard fixtures and hardened gauge blocks, offering low maintenance and predictable service life. The moderate mass and compact format also simplify storage and quick retrieval from tool drawers or inspection kits. Practical integration into inspection workflows As a dedicated pin gauge for end‑dimension checking, this item suits batch inspection, first‑article testing and assembly verification tasks. The clear nominal size and traceable SKU make inventory management straightforward, and compatibility with common gauging equipment reduces integration time. When precision and a compact footprint are required, the gauge pin supports rapid, repeatable checks and a dependable baseline for quality documentation. For reliable workshop inspection at fine tolerances, source the M323.A83 gauge pin from Metav Werkzeuge — contact our product specialists for application guidance or procurement assistance. Technical Data Article number: M323.A83 GTIN: 4061905063633 Category: Messstifte Facts Diameter: 10.83 mm Length: 50 mm Accuracy: ±0.002 mm Weight: 0.1 kg Special features Material: Special steel Version: Workshop execution Intended use: End‑dimension checks FAQ What is the tolerance of this gauge pin? The M323.A83 gauge pin is manufactured to a tolerance of ±0.002 mm, suitable for fine inspection tasks. Which material is used for the pin? This test pin is made from special steel, chosen for dimensional stability under regular workshop use. For which inspection tasks is this pin suitable? The pin is intended for end‑dimension checks, component fit verification and quick go/no‑go measurements in production settings. How is the product identified for ordering? Order using the article number M323.A83 or the GTIN 4061905063633 to ensure correct delivery. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
10.84mm Gauge Pin 50mm Length Workshop Version, Special Steel - Metav IndustryLine
Take advantage of the combination of high reproducibility, compact handling and workshop‑grade construction for reliable end‑dimension checks; order the gauge pin directly via Metav Werkzeuge or ask the consultants for tailored advice. Gauge pin M323.A84 — inspection pin, 10.84 mm diameter, 50 mm length (Metav IndustryLine) The Gauge pin M323.A84 is a single inspection pin designed for precise end‑measure verification in workshop and small‑parts inspection tasks Workshop version for robust everyday use Diameter 10.84 mm; length 50 mm Special steel for wear resistance Traceable accuracy ±0.002 mm Precision where small differences matter The M323.A84 inspection pin delivers consistent dimensional checks in compact assemblies: with a nominal diameter of 10.84 mm and a length of 50 mm, the pin is classified in the micro size range for fine mechanical work. The manufacturing variation of ±0.002 mm provides a dependable reference when checking bores, gauges or mating parts, reducing uncertainty during routine inspections. The compact geometry keeps handling simple while maintaining a stiff contact edge, which helps to avoid measurement artefacts caused by elastic deformation. Built for repeatable workshop use Constructed from special steel, this single‑piece gauge pin is geared towards repeatability under everyday workshop conditions. The material choice balances wear resistance with machinability, so the pin retains its functional contour across many insertion cycles. Supplied as a single unit, the part is suitable for ad‑hoc checks in production, for use within pin blocks and for integration in inspection fixtures; the robust workshop design ensures minimal maintenance and stable performance during repeated go/no‑go verifications. Practical handling and inspection benefits At a weight of 0.1 kg and a compact form factor, the pin is easy to position by hand or in small jigs, which speeds up batch sampling and final checks. Using an inspection pin of this size simplifies alignment and end‑measure validation on small shafts, bores and mating features, shortening inspection times and improving throughput. The combination of compact design and tight manufacturing tolerance supports higher first‑pass yield and lowers rework rates where accurate end‑dimension control is essential. Contact Metav Werkzeuge for ordering guidance and secure the Metav IndustryLine gauge pin M323.A84 for dependable end‑dimension verification at the workshop bench Technical Data Article number: M323.A84 GTIN: 4061905063640 Category: Messstifte Facts Diameter: 10.84 mm Length: 50 mm Manufacturing variation: ±0.002 mm Weight: 0.1 kg Special features Workshop version Material: special steel Supplied as single piece Suitable for end‑measure inspections FAQ What is the exact diameter and length of this inspection pin? The inspection pin has a diameter of 10.84 mm and a length of 50 mm as specified for the M323.A84 gauge pin. What tolerance can be expected from the part? Manufacturing variation is ±0.002 mm, which ensures reliable repeatability for micro‑scale end‑dimension checks. Which material is used for the pin? The pin is made from special steel, selected for durability and stable contact properties during repeated measurements. Can this pin be used in pin blocks or inspection fixtures? Yes, the single‑piece design and compact dimensions make the pin suitable for use in pin blocks and small inspection fixtures. Is the product supplied individually or in sets? The item is supplied as a single inspection pin under the article number M323.A84. Metav IndustryLine: Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
10.85mm Gauge Pin Single 50mm Length Workshop Version - Metav IndustryLine
A compact, single‑piece gauge pin that combines high dimensional accuracy and a robust special‑steel construction for reliable end‑dimension checks; the 50 mm length and Ø 10.85 mm diameter deliver consistent fit verification in workshop routines. Order this gauge pin directly via Metav Werkzeuge or contact our consultants for application guidance. Metav IndustryLine gauge pin M323.A85 — Ø 10.85 mm, 50 mm length The gauge pin M323.A85 is a single test pin designed for precise end‑dimension and fit verification in workshop and quality‑control environments. Ø 10.85 mm precision gauge 50 mm length workshop version Special steel construction Tolerance ±0.002 mm accuracy Precision that keeps production within tolerance The gauge pin is engineered for repeatable measurement when confirming end dimensions or assessing bore fits. With a nominal diameter of Ø 10.85 mm and a verified tolerance of ±0.002 mm, the pin supports tight inspection limits typical in fixture and gauge work. The result is fewer rejects and more reliable inline checks; by converting a visual fit test into a measurable datum, process stability is improved and rework reduced. Robust design for everyday workshop use A 50 mm shank length provides a practical balance between handling and reach, while the workshop version construction resists everyday wear. Manufactured from special steel, the component offers mechanical resistance suited to repeated insertion and withdrawal cycles. The straightforward geometry makes the pin easy to integrate into go/no‑go fixtures or manual inspection kits, enhancing throughput without complicating the inspection routine. Simple implementation, clear measurement outcomes As a single‑item test pin from Metav IndustryLine, the M323.A85 supports rapid verification tasks on production lines or in toolrooms. The compact layout enables quick comparison of mating parts and immediate decision making on assembly compatibility. Where documented traceability is required, the pin’s consistent diameter and tolerance facilitate straightforward recording of pass/fail results within quality documentation and measurement logs. Order the Metav IndustryLine gauge pin M323.A85 via Metav Werkzeuge in Emmerich — call +49 2822 7131930 or email info@metav-werkzeuge.com for technical clarification and fast processing Technical data SKU: M323.A85 GTIN: 4061905063657 Brand: Metav IndustryLine Material: special steel Facts Diameter: 10.85 mm Length: 50 mm Tolerance: ±0.002 mm Weight: 0.1 kg Special features Workshop version Single test pin for end‑dimension checks Compact design for go/no‑go and fit verification FAQ What is the delivered tolerance of the gauge pin? The Metav IndustryLine gauge pin M323.A85 is specified with a tolerance of ±0.002 mm, suitable for tight fit and end‑dimension verification. Which material is used for this test pin? The pin is made from special steel, offering durability for repeated inspection cycles and stable mechanical behaviour. Is this pin intended for workshop or laboratory use? This is a workshop version designed for routine quality‑control tasks, jigs and fixture checks rather than specialised laboratory metrology. How is the product supplied? The item is supplied as a single test pin (SKU M323.A85) for direct integration into inspection kits and gauge sets. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
10.86mm Gauge Pin, Single, 50mm Length, Special Steel, Workshop Version, Supplied in Case - Metav IndustryLine
Combining a tight diameter tolerance of ±0.002 mm, a precise 10.86 mm nominal diameter and a compact 50 mm length, this workshop-grade gauge pin delivers repeatable end-dimension checks and reliable fit verification for production and inspection tasks. Order the gauge pin directly via Metav Werkzeuge or consult our specialists for tailored advice. Gauge pin, single, 10.86 mm Ø, 50 mm length — Metav IndustryLine workshop version The gauge pin, single, 10.86 mm Ø, 50 mm length is a compact, high-precision cylindrical pin intended for end-dimension verification and fit testing in workshop and bench inspection settings High-precision tolerance ±0.002 mm Diameter 10.86 mm for accurate fit checks 50 mm length in special steel Workshop version with robust finish Reliable precision for recurring fit checks The workshop-grade pin is manufactured to a diameter of 10.86 mm with a manufacturing tolerance of ±0.002 mm, a specification that directly reduces false rejects and rework in serial inspection. By providing a stable reference dimension, the pin enables consistent go/no-go evaluations and quick functional checks of bores, seats and mating components. The compact form factor and hardened material deliver the rigidity needed for repeatable measurements, so inspection cycles become both faster and more predictable. Durable construction and measurable benefits Made from special steel, the pin is finished for wear resistance and easy cleaning, which prolongs service life under workshop conditions. The small mass and 50 mm length make handling straightforward during assembly checks, while the close tolerance minimises uncertainty when gauging mating parts. In practice, this means fewer measurement iterations and reliable pass/fail decisions at the production line or inspection bench. The specification also supports quality-control documentation where pinpoint dimensional consistency is required. Practical applications and handling guidance This precision pin is suited to bench inspection, assembly verification and setup tasks in toolrooms and small-batch production. Typical uses include checking final bore sizes, verifying seating surfaces and confirming mating fits before assembly. For handling, keep the pin free of burrs and contamination and store it dry to preserve the measured surface. For tailored integration into existing gauge sets or inspection routines, technical guidance is available from Metav’s product advisors, who can advise on best practices for effective implementation. Choose the Metav IndustryLine gauge pin for dependable end-dimension gauging and contact Metav Werkzeuge in Emmerich for purchasing or technical consultation at info@metav-werkzeuge.com or +49 2822 7131930 Technical data Article number: M323.A86 GTIN: 4061905063664 Brand: Metav IndustryLine Category: Gauge pins Facts Diameter: 10.86 mm Length: 50 mm Manufacturing tolerance: ±0.002 mm Weight: 0.1 kg Special features Workshop version Material: Special steel Supplied individually Application: End-dimension checks FAQ What is the primary purpose of this gauge pin? The gauge pin is designed for end-dimension verification and fit testing; the Metav IndustryLine gauge pin (SKU M323.A86) provides a reliable reference for bore and seating checks. What tolerance does the pin guarantee? The pin is specified with a manufacturing tolerance of ±0.002 mm, which ensures tight dimensional control for accurate fit verification during inspection and assembly. What material is used and how durable is it? Constructed from special steel, the pin features a workshop-grade finish that resists wear under routine inspection conditions and supports repeated use. Is the pin supplied individually or in sets? This item is supplied individually, as indicated in the product description, allowing flexible use in bespoke inspection workflows. Where is this gauge pin typically used? Typical applications include bench inspection, toolroom checks and final fit verification in small-batch production and maintenance environments using the Metav IndustryLine pin. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
10.87mm Gauge Pin, Single, 50mm Length, Workshop Version - Metav IndustryLine
Combine high repeatability and robust workshop construction to secure reliable end‑measurement results; with ±0.002 mm tolerance and a 10.87 mm diameter this single gauge pin supports consistent inspection and fixture alignment. Order the gauge pin directly via Metav Werkzeuge or contact our consultants for application advice. Gauge pin M323.A87 — 10.87 mm diameter, 50 mm length (Metav IndustryLine) A gauge pin designed for precise end‑measurements and routine workshop inspection tasks, supplied as a single, workshop‑grade test pin. Workshop execution, robust design Diameter 10.87 mm, length 50 mm High precision: ±0.002 mm accuracy Precision that reduces rework and speeds inspection The solid construction delivers measurable benefits in production control: ±0.002 mm repeatability substantially lowers measurement uncertainty compared with coarse gauges, making the pin suitable for fine inspection tasks and tolerance checks. With a nominal diameter of 10.87 mm and a 50 mm shank length the component is optimised for reliable insertion in bores, alignment of fixtures and end‑measurement checks. The narrow tolerance bandwidth supports process stability, reducing the likelihood of scrap and minimising downstream rework in batch production. Built for daily workshop use and fixture integration The workshop execution and special steel composition of the pin ensure robust handling and longevity under frequent use. The compact length keeps handling straightforward on assembly benches and in test rigs, while the moderate mass contributes to nimble manipulation without compromising stiffness. Designed as a single‑piece test instrument, the pin is particularly suitable for use as an end mass in jigs, for transfer checking and as a reference gauge in routine control loops. Its construction emphasises durability and consistent contact surfaces for repeated measurements. Practical compatibility and measurement workflow benefits Integration into inspection routines is straightforward: the pin functions as a reference element for bore checking, alignment and comparative gauging within inspection fixtures. Its nominal dimensions and tight accuracy make it compatible with established measuring setups and repeatable hand and bench procedures. For demanding production environments that require verifiable end‑measurement, the pin supports traceable checks when combined with calibrated masters and measurement benches. Detailed identifiers such as the SKU M323.A87 and GTIN facilitate inventory and documentation in quality systems. For precise end‑measurement applications, contact Metav Werkzeuge to request the Metav IndustryLine gauge pin M323.A87 and discuss suitability for specific inspection workflows. Technical data Article number: M323.A87 GTIN: 4061905063671 Brand: Metav IndustryLine Material: Special steel Weight: 0.1 kg Label: Gauge pin, single, 10.87 mm, length 50 mm Facts Diameter: 10.87 mm Length: 50 mm Tolerance / Accuracy: ±0.002 mm Weight: 0.1 kg Special features Workshop execution Single test pin delivery Suitable for end‑measurement and fixture alignment Robust contact surfaces for repeated use FAQ What is the intended use of this gauge pin? The gauge pin M323.A87 is intended for end‑measurement, bore checking and fixture alignment in workshop and inspection applications where tight repeatability is required. How precise is the pin and what does ±0.002 mm mean in practice? An accuracy of ±0.002 mm indicates a very small manufacturing deviation from nominal diameter, allowing the pin to serve as a reliable reference for tight tolerance checks and to reduce measurement variability. Which material is used and why does it matter? The pin is made from special steel, chosen for wear resistance and stable contact surfaces, which is important for maintaining consistent dimensions over repeated inspection cycles. Can this pin be used in production fixtures? Yes, the pin’s 50 mm length and robust workshop design make it suitable for integration into jigs and fixtures for alignment and comparative gauging operations. Is the SKU and GTIN available for documentation? Stock and traceability details are provided: SKU M323.A87 and GTIN 4061905063671, which support inventory management and quality records. Metav IndustryLine: Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
10.88mm Gauge Pin 50mm Length Workshop Version, Special Steel - Metav IndustryLine
A compact inspection solution combining high dimensional fidelity and robust workshop handling: the gauge pin, single, Ø10.88 mm, length 50 mm delivers a tight ±0.002 mm tolerance on a special steel body for reproducible checks. Order the item directly via Metav Werkzeuge or ask the consultants for application support. Gauge pin, single, Ø10.88 mm — 50 mm length, ±0.002 mm (Metav IndustryLine) The Gauge pin, single, Ø10.88 mm, length 50 mm is a micro‑class inspection pin for precise dimensional checks and plug‑gauge applications in workshop and small‑part quality control. Precision Ø10.88 mm with ±0.002 mm tolerance 50 mm length in hardened special steel Workshop design for robust daily inspection Compact micro‑class gauge for fine components Precision that makes measurements repeatable The design focuses on measurable reliability: a nominal diameter of Ø10.88 mm combined with an ±0.002 mm tolerance yields repeatable reference points for go/no‑go checks, fixture setting and comparative measurement tasks. That level of accuracy reduces rework by narrowing acceptance bands and supports tight production tolerances. The construction in special steel provides dimensional stability under typical workshop conditions while keeping the component compact enough for confined jigging situations. Built for robust handling and straightforward inspection With a 50 mm working length and a mass of approximately 0.1 kg, this inspection pin is sized for easy handling and integration in manual and semi‑automatic test setups. The workshop version construction emphasises durability: surfaces are finished to resist quick wear and to preserve the reference diameter under repeated seating in bores and gauges. As a compact, micro‑class tool, it is particularly useful where space is limited but accuracy must not be compromised—for example when checking small bearings, housings or alignment pins. Seamless integration into quality workflows The item is supplied under the Metav IndustryLine programme with identifiers for procurement and inventory: M323.A88 and GTIN 4061905063688 make it straightforward to document in inspection plans and ERP systems. As a single, standardised reference pin it simplifies fixture setup, reduces measurement variability and makes periodic cross‑checks between operators more consistent. The combination of high geometric fidelity and workshop resilience supports efficient first‑article inspection and ongoing process control. Contact Metav Werkzeuge in Emmerich to request technical datasheets or to reserve the M323.A88 gauge pin for workshop inspection — phone +49 2822 7131930 or info@metav-werkzeuge.com Technical data SKU: M323.A88 GTIN: 4061905063688 Description: Gauge pin, single, Ø10.88 mm, length 50 mm Material: Special steel Weight: 0.1 kg Facts Diameter: 10.88 mm Length: 50 mm Tolerance: ±0.002 mm Category: Gauge pins (Messstifte) Special features Workshop version Compact micro‑class format High dimensional fidelity Eclass: 21170231 FAQ What is the declared dimensional tolerance of this inspection pin? The gauge pin is specified with a tolerance of ±0.002 mm, providing high‑precision reference for close‑tolerance checks. Which material is used for the pin body? The product is made from special steel, selected for dimensional stability and wear resistance in workshop environments. Is this pin suitable for use in small bore gauging and fixture setting? Yes — the compact micro‑class diameter and 50 mm length make the pin well suited to small bore gauging, fixture alignment and component seating checks. How is the item identified for procurement and documentation? The gauge pin is listed under SKU M323.A88 and GTIN 4061905063688 for clear traceability in ordering and quality records. Does the product data indicate delivery with a calibration certificate? No calibration certificate is indicated in the supplied product data for this item. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
10.89mm Gauge Pin, Single, 50mm Length, Workshop Version - Metav IndustryLine
Take advantage of precision, compactness and workshop-ready robustness: the combination of a tight ±0.002 mm tolerance, a 10.89 mm nominal diameter and a 50 mm length ensures repeatable checks of bore and end dimensions under daily production conditions. Order the gauge pin directly via Metav Werkzeuge or consult our advisers for application-specific recommendations. Gauge pin M323.A89 — 10.89 mm diameter, 50 mm length (Metav IndustryLine) A gauge pin designed for reliable verification of bores and end dimensions in workshop inspection and small-series production. Workshop-grade special steel construction Diameter 10.89 mm, tolerance ±0.002 mm 50 mm overall length for compact inspections Supplied individually for flexible use Consistent diameter control that reduces rework The compact inspection pin delivers absolute focus on one task: diameter verification. With a nominal diameter of 10.89 mm and a verified tolerance of ±0.002 mm, the pin supports quick go/no-go assessments and detailed checks where repeatability matters. The small footprint of the component speeds handling and reduces fixture complexity, so measurement cycles become faster and less error-prone. For routine quality control, the tight tolerance provides a clear, objective basis for acceptance decisions and downstream process adjustments. Workshop-ready design for everyday handling Built in a workshop version for frequent use, the pin is manufactured from special steel selected for dimensional stability under mechanical stress. The 50 mm overall length offers a balance between reach and rigidity, aiding secure holding in vises or test fixtures without excess overhang. Supplied individually, the single-piece format simplifies inventory and allows technicians to select precise sizes as needed. The combination of practical length and robust material reduces handling-induced variation and supports a steadier inspection routine on the shop floor. Traceable components that fit quality workflows Identification and traceability are straightforward: the item is listed as SKU M323.A89 with GTIN 4061905064333, simplifying stock management and integration into inspection plans. The precision class and stable geometry make this pin suitable for repetitive checks during assembly and final inspection, helping to keep non-conforming parts from progressing through the process. For specialised requirements or measurement strategies, Metav IndustryLine advisers can clarify fitment into existing gauges or fixtures and suggest compatible control practices. Ensure consistent inspection results with Metav IndustryLine gauge pins — contact Metav Werkzeuge in Emmerich for delivery options and application guidance Technical data Article number: M323.A89 GTIN: 4061905064333 Category: Gauge pins (Messstifte) Label: Prüfstift, einzeln, 10,89 mm Länge 50 mm Numerical data Nominal diameter: 10.89 mm Length: 50 mm Weight: 0.1 kg Tolerance: ±0.002 mm Features Material: Special steel Version: Workshop execution Supplied: Single item eClass: 21170231 FAQ What is the primary use of this gauge pin? The gauge pin M323.A89 from Metav IndustryLine is intended for verification of bore diameters and end dimensions in workshop inspection and small-series production. What tolerance can be expected from the pin? The inspection pin is specified with a tolerance of ±0.002 mm, providing high repeatability for go/no-go checks and dimensional assessments. Is the material suitable for daily workshop use? Yes, the pin is manufactured from special steel in a workshop-grade execution, offering dimensional stability under regular handling. How is the item identified for inventory and traceability? Identification is via SKU M323.A89 and GTIN 4061905064333, which supports integration into inventory systems and inspection documentation. Can this pin be integrated into existing gauges or fixtures? The pin's compact length and standard diameter make it straightforward to incorporate into fixtures; Metav IndustryLine advisers can recommend specific mounting or complementary gauge elements. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
10.8mm Gauge Pin 50mm Length Workshop Version, Special Steel In Plastic Case - Metav IndustryLine
Take advantage of the combination of workshop-grade construction, tight dimensional tolerance and compact dimensions for reliable end-size inspection. Order the inspection pin directly via Metav Werkzeuge or consult our specialists for application advice. Gauge pin M323.A80 — 10.8 mm diameter, 50 mm length (Metav IndustryLine) A Gauge pin M323.A80 intended for precise end-size checks and routine dimensional verification in workshop and inspection environments. 10.8 mm diameter precision pin 50 mm overall length Accuracy ±0.002 mm tolerance Workshop-grade special steel Consistent dimensional control with tight tolerance The M323.A80 is built for repeatable verification of finished dimensions: with an accuracy of ±0.002 mm the pin supports high-precision pass/fail and reference measurements during machining and assembly. Stated tolerance levels allow straightforward interpretation against drawing limits and inspection plans, which speeds up quality decisions and reduces rework. The clear numeric specification also makes this pin suitable for use in documented quality-control procedures and calibration routines. Robust, workshop-ready construction for everyday use Manufactured from special steel and specified as a workshop-grade execution, this measuring pin balances hardness and toughness for frequent handling. The compact form—10.8 mm diameter with a 50 mm overall length—minimises flex and provides a stable reference when inserted into holes or used against datum faces. The mechanical simplicity of the design reduces maintenance needs and ensures straightforward handling on the shop floor, contributing to dependable inspection throughput. Practical applications and measured benefits for production Designed for end-size inspection and incremental checks, the pin is particularly useful for verifying hole diameters, locating features and checking bores during in-process or final inspection. As a single inspection instrument, it serves as a direct, low-complexity measuring aid that integrates easily into existing workflows. Using a dedicated gauge pin like this one helps to standardise measurement routines, shorten inspection times and maintain consistent quality across batches. Contact Metav Werkzeuge today to discuss how the M323.A80 can be integrated into current inspection routines or to request a specification sheet referencing the M323.A80 Technical data Article number: M323.A80 GTIN: 4061905063602 Label: Inspection pin, single, 10.8 mm diameter, 50 mm length Facts Diameter: 10.8 mm Length: 50 mm Weight: 0.1 kg Accuracy: ±0.002 mm Special features Material: Special steel Workshop execution Category: Gauge pins FAQ What tolerance can be expected from this gauge pin? The single inspection pin is specified with an accuracy of ±0.002 mm, enabling precise end-size and reference checks. Is the M323.A80 suitable for bore inspection on the shop floor? Yes, this gauge pin is designed for routine bore and hole verification in workshop environments thanks to its compact 10.8 mm diameter and 50 mm length. Which material is the pin made from and what does that mean for durability? The pin is made from special steel, chosen for its balance of wear resistance and toughness appropriate for regular inspection use. Is the product supplied as a single unit or in a set? The article is offered as a single inspection pin; the product designation indicates the individual item format. Can this pin be used as a reference in quality documentation? Yes, the clear numeric specification (diameter, length and ±0.002 mm accuracy) supports use as a documented reference in inspection records and control plans. Metav IndustryLine: Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
10.9 mm Test Pin Length 50 mm Workshop Version, Special Steel Kitted - Metav IndustryLine
Take advantage of the combination of high repeatability, robust special-steel construction and a compact 50 mm length for reliable end measurements in workshop routines; order the gauge pin directly via Metav Werkzeuge or consult our specialists for application advice. Gauge pin, single — 10.9 mm diameter, 50 mm length (Metav IndustryLine) Gauge pin, single, 10.9 mm diameter and 50 mm length is a workshop-grade measuring pin designed for precise end measurements and checking bore fits Tolerance ±0.002 mm Diameter 10.9 mm, length 50 mm Made from special steel Workshop-grade single pin delivery Precision that reduces rework and inspection time The gauge pin is manufactured to a tolerance of ±0.002 mm, providing a measurable advantage where repeatable end measurements are required. Such fine tolerances translate into fewer ambiguous fit checks and reduced rework cycles on production parts. Used as a reference pin for checking bore sizes or verifying final dimensions, the component’s 10.9 mm diameter and compact 50 mm length offer a balance between handling convenience and the rigidity needed for reproducible results. This level of precision supports process stability in workshop environments and contributes directly to improved throughput. Robust material and workshop-focused design Constructed from special steel, the pin is optimised for repeated contact and routine inspection use. The workshop-grade execution emphasises durability under regular handling while maintaining surface integrity for consistent measurements. Supplied as a single pin, this item suits toolboxes and inspection kits where individual replacement sizes are required. The compact format and material choice reduce the risk of deformation under standard use, increasing the service life of the gauge and preserving measurement confidence over many cycles. Integration into quality workflows and supply reliability As part of the Metav IndustryLine, this gauge pin benefits from being offered by an established precision distributor with a practical European stock approach. Metav’s inventory and quality filter aim to make high-precision measuring tools accessible for workshops and small-series manufacturers alike, supporting continuous production without lengthy procurement delays. Choosing this pin aids reliable in-house checks and complements production control activities, helping maintain conformity across batches and supporting traceable inspection routines. For assured precision in end measurements, contact Metav Werkzeuge to secure this Metav IndustryLine gauge pin (SKU M323.A90) and discuss immediate supply options via info@metav-werkzeuge.com or +49 2822 7131930 Technical data SKU: M323.A90 GTIN: 4061905064340 Label: Prüfstift, einzeln, 10,9 mm Länge 50 mm Manufacturer: Metav IndustryLine Facts Diameter: 10.9 mm Length: 50 mm Tolerance: ±0.002 mm Weight: 0.1 kg Special features Material: special steel Workshop execution (Werkstatt-Ausführung) Single gauge pin (individual delivery) Category: Messstifte FAQ What accuracy can be expected from this gauge pin? The gauge pin is specified with an accuracy of ±0.002 mm, making it suitable for precise end measurements and repeatable fit checks in a workshop environment. Which material is the pin made from and why does it matter? The pin is made from special steel, selected to provide wear resistance and dimensional stability under routine inspection use, which preserves measurement reliability. Can this pin be used to check bore diameters? Yes, the gauge pin serves for end measurements and bore checks where a 10.9 mm reference diameter and 50 mm length are appropriate for the application. How is the product identified for reordering? Reorder using SKU M323.A90 or GTIN 4061905064340; both identifiers are listed for straightforward procurement and inventory control. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
10.91mm Gauge Pin Single 50mm Length Workshop Version - Metav IndustryLine
Take advantage of the combination of fine tolerance, compact dimensions and workshop-ready robustness for consistent end‑measure checks; the 10.91 mm diameter and 50 mm length enable repeatable fit and alignment tasks. Order the gauge pin directly via Metav Werkzeuge or ask our consultants for application advice. Gauge pin M323.A91 — single test pin, 10.91 mm diameter, 50 mm length Gauge pin M323.A91 as a single inspection pin for end‑measure checks and small‑part alignment in workshop and toolroom environments. Workshop version for daily use Diameter 10.91 mm, length 50 mm Tolerance ±0.002 mm Delivered in a protective case Precision for compact inspection tasks The M323.A91 is engineered for precision in confined setups where small deviations matter. With a nominal diameter of 10.91 mm and an overall length of 50 mm, this single gauge pin is suited to checking end dimensions, locating holes and verifying fit‑up on small assemblies. The specified ±0.002 mm tolerance expresses the manufacturing accuracy and supports repeatable go/no‑go and fit checks, reducing uncertainty during incoming inspection and assembly operations. Thanks to the compact form factor, the pin simplifies handling when access is restricted. Built for workshop durability and ease of handling Presented as a workshop version, the pin is manufactured from special steel to withstand frequent use in production and maintenance settings. The robust construction limits surface deformation under normal handling and contributes to consistent measurement outcomes over time. For transport and protection, the item is supplied in a protective case, which reduces the risk of damage during storage and transit and keeps the inspection tool ready for immediate use at the bench or in the fixture bay. Designed application range and practical benefits Classified in the Micro range (measurement range up to 100 mm), this inspection pin addresses the needs of watchmaking, precision component assembly, jigs, fixtures and detailed quality control tasks. The compact dimensions make it convenient for insertion into tight bores and for use as a reference mandrel during alignment operations. The single‑piece design supports straightforward acceptance criteria and is compatible with common test benches and manual gauging procedures used in small‑part production. Traceability and workshop integration The gauge pin is supplied with manufacturer traceability details to aid stock management and documentation: SKU M323.A91 and GTIN 4061905064357 identify the item for ordering and inventory systems. Delivered as a single‑unit inspection pin in a transport case, the component integrates easily into standard tool sets and metrology trays, supporting efficient inspection workflows. Metav’s role as a precision partner ensures reliable sourcing and a quality filter for European customers, helping to maintain production continuity. Contact Metav Werkzeuge for specification checks and supply of the Metav IndustryLine gauge pin M323.A91 — our Emmerich team will advise on compatibility and delivery options. Technical data Article number: M323.A91 GTIN: 4061905064357 Manufacturer: Metav IndustryLine Material: Special steel Weight: 0.1 kg Length: 50 mm Diameter: 10.91 mm Facts Diameter: 10.91 mm Length: 50 mm Tolerance: ±0.002 mm Weight: 0.1 kg ECLASS: 21170231 Special features Workshop version Protective case for transport Single gauge pin for end‑measure checks Story trigger: endmasse FAQ What are the main dimensions of this gauge pin? The gauge pin M323.A91 has a diameter of 10.91 mm and a length of 50 mm, suited to precise end‑measure checks. What level of tolerance can be expected? Manufacturing tolerance for the M323.A91 is ±0.002 mm, providing consistent results for fit and go/no‑go assessments. Which material is used for the pin? The pin is made from special steel, chosen for durability in workshop environments and repeated handling. Is the pin supplied ready for use in workshops? Yes, the M323.A91 is delivered as a workshop version and comes in a protective case for transport and storage. For which applications is this gauge pin designed? This single inspection pin is intended for end‑measure checks, alignment and small‑part verification in toolrooms, fixtures and precision assembly work. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
10.92mm Test Pin 50mm Length Workshop Version - Metav IndustryLine
Take advantage of the combination of workshop‑grade robustness, ±0.002 mm tolerance and compact handling for reliable end‑measure checks; order the gauge pin directly via Metav Werkzeuge or ask the consultants for application advice. Gauge pin M323.A92 — single gauge pin, ø 10.92 mm × 50 mm, workshop version (Metav IndustryLine) A gauge pin M323.A92 designed for precise end‑measure and fit verification in workshop inspection routines. Workshop version, robust design Diameter 10.92 mm for end‑measure checks Tolerance ±0.002 mm for precise fits Delivered in a protective case Repeatable precision for end‑measure checks This single gauge pin is manufactured from special steel and finished for consistent contact geometry, delivering a declared tolerance of ±0.002 mm. Such accuracy ensures that plug‑fit and end‑measure verifications produce reproducible results when used as a reference in go/no‑go checks or gauge stacks. The compact 50 mm overall length and 10.92 mm diameter make the component particularly suited to bench‑level inspection tasks where stability and repeatability are essential. The declared precision supports efficient quality control decisions and reduces rework driven by uncertain fits. Robust workshop design that withstands daily use Engineered as a workshop variant, the component combines a hardened surface with a geometry that resists edge damage during repeated handling. The choice of special steel balances wear resistance with measured machinability so that the pin maintains its profile across many cycles. This durability translates into lower replacement frequency and predictable performance on the shop floor, contributing to faster inspection throughput and reduced downtime in production sequences. Practical handling and protected transport At 50 mm length the gauge pin remains easy to position and measure with standard holders and measurement fixtures; the short, stiff form reduces bending and handling error during insertion. Delivery in a protective case keeps the reference surface free from knocks and contamination in storage and transit, preserving the calibration state until first use. Where traceability is required, the product’s marking and packaging simplify inventory assignment and secure integration into a calibrated gauge set. Typical uses and material compatibility The inspection pin is optimised for end‑measure verification, go/no‑go stacking and assembly checks in general mechanical and maintenance workshops. Its geometry and tolerance make it suitable as a reference in small‑component assemblies and for spot checks on mating bores. The special steel construction is aimed at typical workshop environments; compatibility with specific materials should be evaluated in cases involving abrasive or corrosive media. For an application review or to secure the Metav IndustryLine gauge pin M323.A92 for an inspection kit, contact Metav Werkzeuge in Emmerich — eMail info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: M323.A92 GTIN: 4061905064364 Brand: Metav IndustryLine Material: Special steel Weight: 0.1 kg Length: 50 mm Diameter: 10.92 mm Tolerance: ±0.002 mm Core specifications Diameter: 10.92 mm Length: 50 mm Mass: 0.1 kg Accuracy: ±0.002 mm SKU: M323.A92 Special features Workshop execution Single gauge pin for end‑measure checks Delivered in protective case Suitable for inspection and fit verification Compact, stiff geometry for repeatable handling FAQ What is the declared tolerance of this gauge pin? The declared tolerance for the Metav IndustryLine gauge pin M323.A92 is ±0.002 mm, specified for consistent fit and end‑measure checks. Is the gauge pin supplied ready for use and protected in transit? Yes, the inspection pin is supplied in a protective case to preserve the measuring surface and simplify storage until deployment. Which materials is the pin suitable for checking? The pin is made from special steel and is intended as a reference for mechanical assemblies and mating bores; compatibility with specific materials should be considered case by case. Can the pin be used in go/no‑go gauge stacks? The component’s tight tolerance and consistent geometry make it suitable as a reference element within gauge stacks and simple go/no‑go arrangements. What is the overall length and diameter of the pin? The gauge pin measures 50 mm in length with a 10.92 mm diameter, a compact format for bench inspection and assembly checks. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
10.93mm Test Pin 50mm Length Workshop Version - Metav IndustryLine
Combining workshop‑grade construction, a compact 50 mm length and a tight tolerance of ±0.002 mm, this test pin delivers repeatable end‑measure checks and reliable gauge setting in production and inspection workflows. Order the test pin directly via Metav Werkzeuge or consult our technical advisers for application support. Test Pin M323.A93 — 10.93 mm diameter, 50 mm length (Metav IndustryLine) Test Pin M323.A93 is a workshop‑grade reference pin for precise end‑dimension checks and gauge setting in machining and inspection environments. Workshop‑grade construction Diameter 10.93 mm precision Tolerance ±0.002 mm Delivered in protective transport box Reliable reference for repeatable end‑measure checks The M323.A93 test pin is designed as a compact, high‑precision reference component, offering a 10.93 mm nominal diameter and 50 mm overall length that suit fine adjustment and end‑dimension verification. With a specified tolerance of ±0.002 mm, the pin provides a measurable reduction in measurement uncertainty compared with coarse references, which improves first‑pass yield and shortens inspection loops. The chosen special steel material combines surface hardness and dimensional stability, so repeatability is maintained across routine handling and tactile gauging. Built for workshop handling and fixture use As a workshop‑grade article, this reference pin balances robustness with easy handling: the compact geometry minimises bending and makes the pin straightforward to seat in fixtures or indicator stands. Delivery in a protective transport box preserves the calibrated surface during transport and storage, reducing downtime caused by reconditioning. The modest mass (approximately 0.1 kg) simplifies manual placement while giving sufficient inertia for stable contact with probes and comparators, supporting faster and more consistent inspection cycles on the shop floor. Clear technical identity and stock integration The component is supplied as a single reference pin and carries the internal SKU M323.A93 and GTIN 4061905064807, facilitating inventory control and traceability in procurement systems. The compact dimensions place the item in the Micro measurement class (max. 10–100 mm), which is the preferred range for fine mechanical work and fixture assembly—this classification helps selecting the right tool for watchmaking, small housings or precision gauge construction. For specialised applications or batch supply, Metav’s product specialists can advise on storage, handling and compatibility with existing test jigs. For robust workshop inspection and dependable gauge references, choose the Metav IndustryLine test pin and contact Metav Werkzeuge in Emmerich for tailored delivery and advice: info@metav-werkzeuge.com • +49 2822 7131930 Technical data Article number: M323.A93 GTIN: 4061905064807 Material: Special steel Length: 50 mm Diameter: 10.93 mm Weight: 0.1 kg Tolerance: ±0.002 mm Facts Measurement class: Micro (max. 10–100 mm) Delivery: single test pin Label: Prüfstift, einzeln, 10,93 mm Länge 50 mm Special features Workshop‑grade design Delivered in protective transport box Workshop execution SKU: M323.A93 FAQ Is the test pin suitable for use as a reference in small fixture assemblies? Yes. The test pin is specified for precision reference duties in small fixtures and assemblies; with a 10.93 mm diameter and ±0.002 mm tolerance it is suitable for fine positional and end‑dimension checks. What material is the pin made from and how does that affect wear? The pin is manufactured from special steel, chosen for dimensional stability and surface resistance; this supports repeated contact with gauges and probes without rapid degradation. How is the item delivered and how should it be stored? The test pin is supplied as a single unit in a protective transport box, intended to protect the measuring surface during storage and transport; dry, dust‑free storage minimises corrosion risk. Can this pin be ordered in larger quantities for production use? Yes. The SKU M323.A93 and GTIN 4061905064807 facilitate bulk ordering and inventory management; Metav IndustryLine can advise on lead times and packaging for larger batches. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
Fast, tactile checks where electronics are impractical
Gauges and test pins provide unequivocal go/no-go results for threads, bores, gaps and radii without relying on electronics. The range covers plug gauges and ring gauges for internal and external threads, feeler gauges and precision feeler strips for micro‑gap assessment, plus probe pins and measuring pins for tactile diameter and pitch checks.
How these tools work in the production environment
Mechanical gauges operate as direct reference standards: a plug gauge or ring gauge verifies conformity to thread profiles and mating ability, while limit gauges separate accept from reject in a single step. Test pins are used to tactilely measure small bore diameters, centre‑to‑centre distances and radii. Manufactured from hardened gauge steel or ceramic and often precision lapped, these instruments deliver immediate physical results that are ideal for incoming inspection, machine‑side checks and final control.
Measurable benefits that affect production performance
- Reduced scrap and rework through rapid, unambiguous pass/fail assessment.
- Increased repeatability thanks to very low measurement uncertainty and fine lapping.
- Lower downtime: quick checks at the machine save cycle time and reduce setup periods.
- Durable construction with high wear resistance from specialised, low‑distortion alloys.
- Versatile delivery formats: individual gauges, organised sets in wooden cases or metre‑length feeler rolls compliant with DIN 2269.
Why Metav is the practical choice for precision supplies
Metav combines decades of expertise with a broad warehouse and quality filtering from Emmerich. As a precision partner for industry, craft and trade, Metav supplies a comprehensive selection of gauges and test pins alongside complementary tools such as precision calipers and setting rings. With over 48,000 customers and a catalogue exceeding 250,000 items, Metav is positioned to supply reliably, reduce vendor complexity and support traceable quality control to national standards.
Summary
Gauges and test pins are indispensable for dependable, repeatable quality assurance where tactile, mechanical verification is preferred. Choose these plug gauges, ring gauges, feeler strips and probe pins when immediate, robust measurement decisions are required on the shop floor.
FAQ
What materials are gauges and test pins typically made from?
Gauges and test pins are usually manufactured from hardened gauge steel for durability and wear resistance; ceramic variants are available where thermal stability and minimal wear are critical.
How do thread gauges ensure mating capability?
Thread plug gauges and ring gauges check flank diameters and thread form against standards, providing a clear go/no‑go verdict that confirms pairability with mating parts.
Which tolerance class should I choose for probe pins and gauge sets?
Select tolerance classes aligned with your inspection requirements; for high‑precision tasks, sets produced to DIN 2269 or equivalent tolerance classes ensure micrometre‑level control and repeatability.
Can feeler gauges measure contact gaps in valve and engine work reliably?
Yes. Feeler gauges and precision feeler strips, supplied either as a fan or metre‑length rolls, allow accurate assessment of valve clearances and contact gaps down to micrometre increments.
How do limit gauges speed up in‑process inspection?
Limit gauges separate good from bad in a single, tactile operation, enabling rapid go/no‑go checks at the machine and reducing both inspection time and the likelihood of human interpretation errors.
Fragen zu diesen Produkten??
Mit mehr als 30 Jahren Erfahrung beraten wir Sie gerne persönlich.
Tel.: +49 2822 7131930
Mail: info@metav-werkzeuge.com