Precision gauge blocks and plug gauges for reliable dimensional control
Mechanical gauge blocks and plug gauges are essential for tactile verification of threads, bores and gap dimensions, providing fast, unambiguous go/no-go results that enhance process reliability and reduce scrap. Designed for industrial metalworking and toolmaking, these precision tools support incoming inspection and final quality checks by delivering traceable measurements in applications such as thread inspection, bore diameter testing and spacing checks. Manufactured from specially hardened, low-distortion alloys and fine-lapped for minimal measurement uncertainty, the range includes thread plug gauges, precision plug gauges and calibration gauge blocks to ensure long-term repeatability and wear resistance.
15.76mm Test Pin, Single, 50mm Length Workshop Version - Metav IndustryLine
A compact, workshop‑grade gauge pin that combines ±0.002 mm accuracy with a Ø15.76 mm measuring diameter and a 50 mm overall length for dependable end‑measurements; order the pin directly via Metav Werkzeuge or consult our specialists for integration into quality control routines. Gauge pin, single Ø15.76 mm — 50 mm length (Metav IndustryLine) Gauge pin, single Ø15.76 mm — 50 mm length (Metav IndustryLine) is a compact, workshop execution gauge pin for precise end‑measurements and reference checks across small components Single gauge pin Ø15.76 mm High accuracy ±0.002 mm Workshop‑grade special steel Compact 50 mm length Lightweight for easy handling Precision that reduces rework and speeds inspection This gauge pin delivers precision where repeatability matters: with an accuracy of ±0.002 mm, the component becomes a reliable reference for small‑part verification and go/no‑go checks. The Ø15.76 mm dimension provides a clearly defined nominal size for end‑measurements, reducing ambiguity in pass/fail assessments. By using a fixed, calibrated master pin operators can minimise measurement scatter, shorten inspection cycles and lower the rate of downstream rework — a tangible efficiency advantage in small‑batch and series production. Robust, workshop‑grade construction for frequent use Manufactured from special steel and supplied in a workshop grade format, the pin withstands repeated insertion and handling typical of shop‑floor operations. The 50 mm overall length balances reach and stiffness: long enough for comfortable placement, yet compact enough to avoid undue flex. The compact design and lightweight mass make it easy to manoeuvre during fixture set‑up or manual inspections, while the material choice supports long service life under regular contact use. Ideal for fine mechanical and micro assembly tasks Suited to micro and precision work, this gauge pin matches the demands of watchmaking, small‑bore assemblies and precision fixturing where tight tolerances control functional fit. The geometry provides a stable contact surface that simplifies alignment and reference transfer on jigs and measuring fixtures. For workshops seeking consistent measurement standards, the fine‑dimension pin functions as a simple, durable datum that complements calipers and micrometres. Practical identification and integration data The pin is ready for immediate use in inspection workflows and is simple to document within a quality system. Its reduced handling weight supports fast repetitive checks and the clear nominal Ø15.76 mm marking aids traceable measurement records. For customers requiring additional technical clarification or assistance integrating the pin into an inspection routine, Metav Werkzeuge offers technical advice and specification support. For reliable micro‑measurement components from Metav IndustryLine, request the gauge pin M323.F76 via Metav Werkzeuge — contact the Metav team at info@metav-werkzeuge.com or by phone on +49 2822 7131930 to confirm suitability and delivery options. Technical data Article number: M323.F76 GTIN: 4061905070167 Manufacturer: Metav IndustryLine Label: Gauge pin, single, Ø15.76 mm, length 50 mm Facts Diameter: 15.76 mm Length: 50 mm Accuracy: ±0.002 mm Weight: 0.1 kg ECLASS: 21170231 Special features Material: Special steel Workshop execution Category: Gauge pins Intended use: end measurements FAQ What tolerance can be expected from this gauge pin? The gauge pin M323.F76 from Metav IndustryLine is specified with an accuracy of ±0.002 mm, making it suitable for fine inspection tasks and tight tolerance checks. Is the pin suitable for repeated shop‑floor use? Yes, the workshop‑grade construction and special steel material of the M323.F76 gauge pin are intended for frequent handling and repetitive inspection routines. For which applications is this gauge pin most appropriate? The pin is designed for micro and small‑part applications such as precision fixturing, small‑bore checks and assembly alignment where a Ø15.76 mm reference is required. How does the pin aid traceability in quality control? The clearly defined nominal diameter and documented article number (M323.F76, GTIN 4061905070167) simplify record keeping and incorporation into inspection plans and measurement logs. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
15.77mm Gauge Pin 50mm Length Workshop Version, Special Steel - Metav IndustryLine
High-precision metrology for routine inspection tasks: the combination of a 15.77 mm diameter, a 50 mm length and a guaranteed ±0.002 mm dimensional accuracy delivers reproducible end‑measure checks and fast go/no‑go decisions on the shop floor. Order directly via Metav Werkzeuge or request application advice from their consultants. Gage pin M323.F77, single — 15.77 mm dia, 50 mm length (Metav IndustryLine) A gage pin M323.F77 designed for accurate dimensional verification and end‑measure inspection in workshop and quality‑control environments. Workshop‑grade execution for daily use Diameter 15.77 mm, length 50 mm Dimensional tolerance ±0.002 mm Special steel construction for durability Precision where it matters for inspection and control Engineered for reliable dimensional checks, this gage pin features a nominal diameter of 15.77 mm with a tight ±0.002 mm manufacturing tolerance. Such specification supports consistent go/no‑go evaluations and repeatable end‑measure verification in incoming inspection and production control. The small mass and compact geometry reduce the influence of handling, while the specified tolerance provides a verifiable basis for acceptance decisions and process documentation. Built for frequent workshop use and maintenance The workshop version is made from special steel and finished to withstand routine handling and indexing in fixtures or gauges. Its 50 mm functional length offers a practical balance between reach and rigidity for common inspection tasks, while the modest mass simplifies manual positioning. The robust design reduces wear in repetitive use, aiding uptime and lowering the frequency of replacement in a busy shop environment. Traceability, ordering and application fit For inventory and procurement the part is listed as SKU M323.F77 and GTIN 4061905070174, allowing straightforward integration into parts lists and procurement systems. The gage pin is suited to end‑measure and plug‑gauge applications where dimensional certainty speeds decision making on assembly lines and at inspection benches. Its workshop execution and material selection make it a pragmatic choice for maintenance departments, toolrooms and quality labs requiring durable metrology hardware. For dependable end‑measure verification, request the Metav IndustryLine gage pin M323.F77 from Metav Werkzeuge in Emmerich or consult their advisors for application guidance Technical data SKU: M323.F77 GTIN: 4061905070174 Category: Messstifte Key figures Diameter: 15.77 mm Length: 50 mm Dimensional tolerance: ±0.002 mm Weight: 0.1 kg Design and special features Workshop execution Material: special steel Single gage pin delivery Suitable for end‑measure and plug‑gauge checks FAQ Is this gage pin suitable for precision inspection? The gage pin M323.F77 is manufactured to a ±0.002 mm tolerance, making it suitable for precise end‑measure checks and repeatable go/no‑go assessments. What are the exact dimensions and identifiers? Diameter 15.77 mm, length 50 mm; SKU M323.F77; GTIN 4061905070174. Which material and finish are used? The part is produced from special steel in a workshop‑grade finish for wear resistance during routine use. How is the item supplied? Supplied as a single gage pin (single unit) and listed under SKU M323.F77. Can this gage pin be used in fixture and gauge assemblies? Yes — the combination of nominal diameter, length and tight tolerance makes it suitable for incorporation into inspection fixtures and gauge assemblies for dimensional checking. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
15.78mm Test Pin Workshop Version 50mm Length, Special Steel - Metav IndustryLine
Take advantage of the combination of high repeatability, compact dimensions and robust workshop design for reliable end‑measure checks. The precise ±0.002 mm tolerance and special steel construction support reproducible results in routine inspection and fixture set‑up; order directly via Metav Werkzeuge or consult our specialists for application advice. Gauge pin M323.F78 — Gauge pin, Ø 15.78 mm · 50 mm length · Metav IndustryLine A gauge pin designed for precise end‑measure checks and alignment tasks in workshop and inspection environments, supplied as a single, workshop‑ready component. Workshop execution, robust finish Diameter 15.78 mm precision Length 50 mm for standard checks Supplied in transport box Precision where repeatability matters The component is manufactured to a tolerance of ±0.002 mm, which ensures repeatable results for small‑bore measurements and alignment references. Classified in the micro measuring range (measuring range up to 100 mm), this design prioritises stiffness and minimal run‑out over long spans, making it suited to close‑tolerance tasks such as end‑measure verification and fixture calibration. The special steel construction contributes to dimensional stability and wear resistance, reducing variation between successive checks. Practical workshop benefits and handling At 50 mm overall length the pin balances reach with easy handling and secure seating in gauges and jigs. The workshop execution features a robust finish that tolerates frequent use and simple cleaning routines, while the modest weight supports ergonomic placement during inspection cycles. Supplied in a protective transport box, the item is ready for immediate inclusion in a shop inspection kit and can be stored safely between uses to preserve surface integrity. Integration into inspection routines and tooling As a single gauge pin, this item is suitable for direct application in plug gauges, reference checks and setup tasks where a compact, highly accurate reference is required. The tight dimensional specification simplifies pass/fail decisions in routine quality control and reduces the need for compensating adjustments in fixtures. Traceable identification and consistent material properties support predictable behaviour across repeated measurements, aiding process stability on the shop floor. For workshop-ready precision and immediate availability, contact Metav Werkzeuge for stock and application support—our Emmerich team provides tailored advice and fast supply arrangements Technical Data SKU: M323.F78 GTIN: 4061905070181 Material: Special steel Version: Workshop execution Category: Gauge pin Weight: 0.1 kg Dimensions & measurable data Diameter: 15.78 mm Length: 50 mm Accuracy: ±0.002 mm Special features Supplied in transport box Single item delivery Robust finish for workshop use FAQ What materials is this gauge pin made from? The gauge pin is made from special steel, chosen for dimensional stability and wear resistance in routine inspection and alignment tasks. What tolerance can be expected from the pin? The pin is specified with an accuracy of ±0.002 mm, suitable for repeatable end‑measure checks and high‑precision workshop applications. Is the item delivered ready for use in a workshop setting? Yes, the product is supplied as a single, workshop execution gauge pin and arrives in a protective transport box for immediate use. Which applications are typical for this gauge pin? Typical uses include plug gauge checks, fixture alignment and end‑measure verification where a compact, high‑precision reference is required. What is the product identifier for ordering? Order using SKU M323.F78 from the Metav IndustryLine range for this gauge pin. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
15.79mm Gauge Pin Length 50mm Workshop Version - Metav IndustryLine
Taking advantage of a compact, workshop-grade design and high dimensional accuracy, this test pin delivers repeatable results for end-measurement and inspection tasks; its ±0.002 mm tolerance and special steel construction support reliable in-process checks. Order directly via Metav Werkzeuge or contact their consultants for procurement advice. Test pin, single, 15.79 mm diameter, 50 mm length — Metav IndustryLine workshop grade with ±0.002 mm tolerance Test pin, single, 15.79 mm diameter, 50 mm length is a precision gauge pin intended for end-measurement and reference checks in workshop and inspection environments, supplied as an individual item for flexible use in fixtures and measuring assemblies. Diameter 15.79 mm, length 50 mm Tolerance ±0.002 mm industrial accuracy Workshop version for robust use Repeatable dimensional control for critical end measurements For routine inspection tasks and final dimensional checks, a compact gauge pin provides a straightforward, reproducible reference that reduces setup time and uncertainty. The M323.F79 is manufactured to a fine ±0.002 mm tolerance, enabling consistent comparison measurements and reliable pass/fail decisions when used as a reference element in fixtures or analogue jigs. The nominal 15.79 mm diameter and 50 mm length are suited to small-assembly checks and end-of-line verification where a stable reference shaft is required. By converting raw dimensions into a mechanical datum, the pin simplifies alignment and measurement processes and reduces interpretation effort during quality control. Robust workshop execution for daily handling and longevity Constructed from special steel, this single test pin is designed for workshop resilience where repeated insertion, seating and contact stresses occur. The workshop version indicates a focus on durability and practical handling: straightforward geometry, easy mounting in holders, and a weight that balances solidity with manoeuvrability. The compact form factor limits cantilever stresses during measurement and aids stable positioning in bore gauges or comparator setups. Material choice and finishing ensure the profile remains true under normal shop conditions, helping to preserve long-term dimensional stability and reduce the frequency of replacement. Easy integration into inspection routines and fixtures A single precision pin integrates cleanly into existing inspection jigs, plug gauge adaptors and bench fixtures. Its standardised diameter and length make it compatible with common localisation methods and enable swift swaps between test stations. The modest mass contributes to safe handling during repeated checks without compromising positional stability. Using a defined, calibrated reference element like this pin streamlines recording of measurement outcomes and supports consistent operator performance across shifts by providing an unambiguous mechanical datum for external or internal seating checks. Practical procurement and traceability for production environments The item is supplied as an individual test pin with clear identification for inventory and traceability. The M323.F79 is a pragmatic choice when a precise, compact reference is required for production control or small-batch inspection. Buying through Metav IndustryLine ensures access to a wide range of complementary measuring accessories and rapid replenishment from an experienced precision partner; this helps maintain steady inspection throughput without expanding supplier lists unnecessarily. For procurement or technical advice on the Metav IndustryLine test pin with ±0.002 mm accuracy, contact Metav Werkzeuge directly to discuss suitability for specific end-measurement tasks and to arrange order processing. Technical Data Article number: M323.F79 GTIN: 4061905070198 Label: Prüfstift, einzeln, 15,79 mm Länge 50 mm Facts Diameter: 15.79 mm Length: 50 mm Tolerance: ±0.002 mm Weight: 0.1 kg Special features Material: Special steel Version: Workshop execution Item type: Single test pin Category: Gauge pin / Messstifte FAQ What measurement accuracy can be expected from this test pin? The M323.F79 test pin is manufactured to a ±0.002 mm specification, providing high repeatability suitable for precision end-measurement checks and reference applications. Is the pin suitable for use in standard pin holders and fixtures? Yes, the single gauge pin is designed for straightforward integration into common pin holders and fixture adaptors used in workshop inspection setups. What material is the test pin made from and how does that affect durability? The pin is made from special steel, chosen to withstand the mechanical demands of regular seating and contact in inspection tasks while maintaining dimensional stability. Can the pin be used for internal and external reference measurements? The compact geometry and defined diameter allow the pin to serve as a mechanical datum for both internal seating checks and certain external alignment tasks when used with appropriate fixtures. How is the item identified for ordering and inventory? The product is listed as M323.F79 with GTIN 4061905070198 for clear traceability and stock management. Metav IndustryLine: Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
15.7mm Test Pin 50mm Length Workshop Version - Metav IndustryLine
The combination of exact dimensional control, workshop-hardened construction and a compact 50 mm length makes this test pin a pragmatic choice for repeated end-face checks and assembly fixtures. Order directly via Metav Werkzeuge or consult their specialists for batch supplies and traceability options. Test pin M323.F70 — Test pin, Ø 15.7 mm, 50 mm length (Metav IndustryLine workshop version) The Test pin M323.F70 is a compact, precision checking pin designed for end-dimension verification and fixture alignment in workshop and general inspection environments. Workshop-grade construction Precision Ø 15.7 mm ±0.002 50 mm length for end-dimension checks Supplied in a transport case Accurate end-dimension verification for routine checks A purpose-made checking pin that delivers repeatable dimensional control: the central diameter of 15.7 mm with an indicated variability of ±0.002 mm is suitable for tight tolerance verifications where reliable go/no-go or position checks are required. Manufactured from special steel, the component maintains geometric stability under normal workshop handling and mounting. The compact form factor reduces lever effects, enabling quick verification of end faces, bores or locating features without excessive setup time while preserving measurement integrity. Durable workshop design that keeps tools ready The workshop configuration emphasises robustness and handling: the body material (special steel) and the shortened overall length ensure resistance to everyday wear in production and assembly contexts. At a weight of approximately 0.1 kg and a nominal length of 50 mm, the pin is easy to position and interchange in gauges or fixtures. Delivery in a practical transport case protects the pin during storage and transit, reducing the risk of accidental damage and keeping reference parts accessible at the point of use. Practical integration into inspection and assembly workflows Designed for integration into measurement benches, fixture blocks or handheld inspection routines, this checking pin supports efficient process checks and fast component sorting. The compact geometry makes it straightforward to mount in common locating arrangements or to use as a reference punch in repetitive assembly tasks. Traceability is supported through the visible SKU on the product label, facilitating inventory control and replacement planning without extended downtime. Traceability and product identification for procurement For procurement and stock-keeping the product is supplied as a single test pin with clear identifiers: SKU M323.F70 and GTIN 4061905069178, which simplify ordering and batch tracking. The workshop variant is configured for practical everyday use rather than laboratory-only environments, offering a balance between durability and dimensional accuracy. Metav IndustryLine’s role as supplier provides a European distribution and quality filter that supports dependable replenishment and centralised ordering for larger operations. Contact Metav Werkzeuge for delivery and bulk-quantity advice on the M323.F70 test pin and ensure the correct reference parts are available at your workshop or assembly line Technical data SKU: M323.F70 GTIN: 4061905069178 Name: Test pin, single, Ø 15.7 mm, length 50 mm Facts Diameter: 15.7 mm Length: 50 mm Weight: 0.1 kg Accuracy: ±0.002 mm Special features Material: special steel Workshop version Supplied in transport case Single-piece delivery FAQ What inspection tasks is this test pin suitable for? The test pin M323.F70 is intended for end-face and locating-feature checks, suitable for go/no-go verification and fixture alignment in workshop environments. Is the pin supplied ready for storage and transport? Yes, the checking pin is supplied in a transport case to protect the part during handling and storage. How is the product identified for reordering? Reorder using SKU M323.F70 or GTIN 4061905069178; both identifiers are printed for traceability and procurement. Can this pin be used in dedicated gauge blocks or fixtures? The compact length and robust steel construction make the M323.F70 compatible with common fixture and gauge-block applications where a Ø 15.7 mm reference is required. Does the material suit everyday workshop use? The pin’s special-steel construction and workshop specification are chosen for durability under routine inspection and assembly operations. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
15.81mm Gauge Pin 50mm Length Workshop Finish - Metav IndustryLine
Take advantage of high repeatability and compact form factor for straightforward end‑dimension checks; the combination of ±0.002 mm accuracy and a 15.81 mm diameter supports reliable gauging in workshop environments. Order the gage pin directly via Metav Werkzeuge or consult the team for application advice. Gage pin M323.F81 — single precision test pin, Ø 15.81 mm, 50 mm length (Metav IndustryLine) Gage pin M323.F81 is a single precision test pin designed for end‑dimension verification and fixture reference in inspection and assembly processes. Workshop-grade construction Diameter 15.81 mm for end measurement Tolerance ±0.002 mm precision Supplied in protective transport case Consistent, measurable accuracy for routine inspection The compact test pin delivers repeatable accuracy with a stated tolerance of ±0.002 mm, which reduces doubt during go/no‑go checks and shortens inspection cycles. As a solid reference element, the component's nominal diameter of 15.81 mm is suited to end‑measurement tasks and small‑bore gauging where precise limiting diameters are required. This level of control supports faster decision‑making on the shop floor and helps to avoid downstream rework. Built to withstand everyday workshop handling Manufactured in special steel, the single‑piece design is aimed at robust, everyday use. The 50 mm overall length gives a practical balance between accessibility and rigidity, while the workshop specification ensures the pin tolerates standard handling without rapid wear. Supplied in a protective transport case, the item remains protected in transit and storage, preserving the calibrated geometry that underpins reliable measurements. Easy integration into fixtures and inspection rigs With a lightweight construction of 0.1 kg and a format as a single test pin, the unit is straightforward to incorporate into bespoke gauges, fixture plates or handheld checking tools. The compact dimensions and nominal tolerance make the component an efficient reference for assembly jigs or comparative measurement set‑ups, helping to speed fixture set‑up and reduce stoppage time. Traceability is supported by the manufacturer identification and GTIN, simplifying procurement and stock control for production environments. For exact fitting and ordering of the Metav IndustryLine gage pin, please contact Metav Werkzeuge directly at info@metav-werkzeuge.com or by phone on +49 2822 7131930 to discuss delivery and suitability for the intended inspection task Technical Data Article number: M323.F81 GTIN: 4061905071140 Manufacturer: Metav IndustryLine Facts Diameter: 15.81 mm Length: 50 mm Weight: 0.1 kg Tolerance: ±0.002 mm Special features Material: special steel Supply: single gage pin Packaging: protective transport case Workshop version FAQ What is the intended use for this gage pin? The gage pin M323.F81 is intended for end‑dimension verification and as a reference element in inspection fixtures and assembly gauges. Is the gage pin suitable for repeated shop‑floor use? Yes, the Metav IndustryLine single test pin is a workshop‑grade component made from special steel and supplied in a protective transport case to maintain geometry during handling. What level of accuracy does the test pin provide? The test pin is manufactured and inspected to a tolerance of ±0.002 mm, providing a high degree of repeatability for routine gauging tasks. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
15.82mm Gauge Pin 50mm Length Workshop Finish - Metav IndustryLine
Precision inspection is ensured by the combination of special steel construction, compact 15.82 mm diameter and a tight ±0.002 mm tolerance, making this pin a dependable reference for workshop checks; order the gauge pin directly via Metav Werkzeuge or ask our consultants if needed. Gauge pin, individual, 15.82 mm (length 50 mm) — Workshop-grade inspection pin by Metav IndustryLine A gauge pin 15.82 mm designed for end‑measure references and plug‑gauge checks in workshop metrology, suitable for repeatable dimensional control and assembly inspection. Workshop-grade construction Diameter 15.82 mm, tolerance ±0.002 mm Supplied in a protective transport case Reliable reference for inspection tasks This gauge pin delivers a stable reference by combining a compact diameter with a machining tolerance of ±0.002 mm, which reduces measurement scatter during go/no‑go and plug‑gauge checks. Made from special steel, the pin resists wear and preserves roundness over repeated insertion cycles, so inspection routines produce consistent data and fewer ambiguous results. Built for workshop use and straightforward handling The 50 mm length and workshop‑grade finish make the pin easy to seat and extract in typical production environments. At around 0.1 kg the component is light to handle yet sufficiently robust for daily use. Supplied in a protective case for transport, the pin arrives ready for secure storage and immediate use on shop floors where repeatability and tool protection matter. Fast integration into quality processes Marked with SKU M323.F82 and traceable via its GTIN, the gauge pin integrates into existing inspection workflows without additional configuration. As an individual gauge pin, it serves as an end‑measure reference for final dimension checks and simplifies setup where precise, repeatable plug measurements are required. The compact form factor supports quick changes between checks, reducing cycle time and supporting steady production flow. Contact Metav Werkzeuge to source Metav IndustryLine gauge pins for reliable workshop inspection; call +49 2822 7131930 or email info@metav-werkzeuge.com to confirm suitability and availability Technical Data Article number: M323.F82 SKU: M323.F82 GTIN: 4061905071157 Category: Gauge pin / Messstifte Brand: Metav IndustryLine Facts Diameter: 15.82 mm Length: 50 mm Tolerance: ±0.002 mm Weight: 0.1 kg Special features Material: special steel Workshop version Single gauge pin, individual supply Supplied in protective transport case FAQ What is the intended use of this gauge pin? This gauge pin (gauge pin 15.82 mm, M323.F82) is intended as an end‑measure reference and plug‑gauge check in workshop metrology and quality control. How precise is the diameter of the pin? The pin is manufactured to a tolerance of ±0.002 mm, providing a high‑precision reference for dimensional checks. What material is the pin made from? The pin is made from special steel, selected for wear resistance and dimensional stability during repeated use. Is the pin delivered ready for storage and transport? Yes, the gauge pin is supplied in a protective transport case to simplify secure handling and storage on the shop floor. Can this pin be used for go/no‑go testing? Yes, the individual gauge pin is suitable as a fixed reference in go/no‑go and plug‑gauge applications where a precise diameter standard is required. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
15.83mm Gauge Pin Length 50mm Workshop Version, Special Steel ±0.002mm - Metav IndustryLine
Take advantage of the combination of high repeatability, workshop‑grade construction and compact dimensions for reliable end‑dimension checks; order the pin gauge directly via Metav Werkzeuge or ask our consultants for technical advice. Pin gauge M323.F83 – 15.83 mm diameter, 50 mm length The Pin gauge M323.F83 is a single, precision inspection pin for end‑dimension control in workshop and production environments. Precision tolerance ±0.002 mm Diameter 15.83 mm, length 50 mm Made from special steel for workshop use Workshop design for robust handling Accurate end‑dimension control for efficient inspection The Pin gauge M323.F83 is built for direct, repeatable measurement of end faces and bore references, offering a declared ±0.002 mm tolerance that supports tight quality limits without complex setup. Its compact 15.83 mm diameter and 50 mm length make it suitable for short‑reach verification tasks where consistent seating and low runout are required. By providing a clear go/no‑go datum and reducing interpretation time in dimensional checks, the gauge helps streamline inspection cycles and limits costly rework — a rational choice for production and maintenance teams focused on throughput and traceability. Robust workshop construction that withstands daily use Constructed from special steel, this single‑piece inspection pin is optimised for workshop conditions where knocks, repeated handling and frequent seating occur. The workshop specification emphasises dimensional stability and surface integrity so that wear‑related drift is reduced over typical service intervals. The material selection and hardened finish translate into long service life and easier maintenance planning, which supports predictable tool replacement intervals and lower lifecycle costs for routine metrology equipment. Micro range classification and practical applications With its measurement span, the gauge sits in the micro range, addressing fine‑mechanical tasks and short‑reach production checks. This class is ideal for precision components such as fittings, small bores and turned parts where short probe lengths reduce bending and measurement uncertainty. The pin functions as a straightforward reference for visual inspection fixtures, setting checks and quick in‑process controls on assembly benches, offering clear efficiency gains compared with improvised gauges or time‑consuming setups. Simple integration and workshop workflow benefits Designed as an individual inspection pin, the unit integrates easily into existing benches, fixture arrays and checking rigs. Its compact geometry and robust finish make it a practical tool for handheld checks or for use in simple mechanical holders. The clear, single‑diameter design reduces operator decisions during sampling and speeds up throughput in repetitive checks, supporting more consistent quality signalling across shifts and machines. For workshop procurement and detailed technical guidance on the Metav IndustryLine pin gauge M323.F83, contact Metav Werkzeuge in Emmerich to arrange supply and application advice. Technical Data Article number: M323.F83 GTIN: 4061905071164 Manufacturer: Metav IndustryLine Facts Diameter: 15.83 mm Length: 50 mm Tolerance: ±0.002 mm Weight: 0.1 kg Special features Material: special steel Single pin gauge (individual) Workshop execution FAQ What diameter is the pin gauge? The pin gauge has a diameter of 15.83 mm, specified for precise end‑dimension checks. What tolerance does the gauge offer? The inspection pin provides a declared tolerance of ±0.002 mm, suitable for fine workshop controls. Which materials is the gauge made from? The unit is manufactured from special steel, chosen for durability in workshop environments. Is this pin gauge intended for large assemblies? This item belongs to the micro range and is optimised for short‑reach components and small bores rather than large structural assemblies. How is the gauge supplied? The product is supplied as a single, individual inspection pin ready for direct use in measuring and checking operations. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
15.84mm Gauge Pin 50mm Length Workshop Finish - Metav IndustryLine
Take advantage of precise diameter control (15.84 mm) and a repeatable tolerance of ±0.002 mm combined with a 50 mm measuring length for consistent end‑dimension verification; order the gauge pin directly via Metav Werkzeuge or ask our consultants if needed Gauge pin, single — 15.84 mm Ø, 50 mm length (Metav IndustryLine) The gauge pin, single — 15.84 mm Ø, 50 mm length is a workshop‑grade inspection pin designed for accurate end‑dimension checks and go/no‑go verification in industrial measuring and assembly tasks Workshop‑grade inspection pin, robust design Diameter precisely 15.84 mm ±0.002 mm 50 mm measuring length for end‑dimension checks Delivered in protective transport box Consistent dimensional control for production workflows The inspection pin provides a compact, reliable reference for end‑dimension checks where repeatability matters. With a nominal diameter of 15.84 mm and a verified tolerance of ±0.002 mm, the pin serves as a fixed reference for setting fixtures, validating bore sizes or performing functional go/no‑go tests. The combination of a defined diameter and a moderate 50 mm length balances handling convenience with sufficient engagement length for many workshop tasks, reducing the need for multiple measuring setups and accelerating inspection cycles. Precision engineering that reduces uncertainty Manufactured from special steel, this measuring pin maintains surface integrity and dimensional stability under typical workshop conditions. The stated ±0.002 mm accuracy ensures narrow scatter in repeated checks, supporting quality control processes where small deviations affect assembly fit. The robust basic geometry minimises deformation under light manual handling, enabling reliable comparative measurements and helping to maintain process capability figures in series production. Practical handling and protection for everyday use The workshop execution prioritises durability and ease of use: the pin's compact form makes it straightforward to position and verify mating parts, while the supplied protective transport box preserves the calibrated surface during storage and transit. At roughly 0.1 kg and a 50 mm length, the component is easy to integrate into portable inspection kits or fixed test rigs alike. This pragmatic design reduces downtime and supports consistent results across shifts and operators. Integration and traceability in the metrology chain As part of a structured measuring setup, the pin complements gauge blocks, bore gauges and plug‑gauge sets to create verifiable inspection routines. The clear identification via SKU and GTIN supports inventory management and traceable procurement, ensuring the reference used for a production batch can be documented and recalled. Where traceability is critical, this simple reference element plays a direct role in maintaining quality records and audit trails. For workshop‑ready precision, specify the Metav IndustryLine gauge pin and contact Metav Werkzeuge in Emmerich for tailored advice or procurement assistance Technical data Article number / SKU: M323.F84 GTIN: 4061905071737 Brand: Metav IndustryLine Facts Diameter: 15.84 mm Measuring length: 50 mm Weight: 0.10 kg Accuracy: ±0.002 mm eClass: 21170231 Special features Material: special steel Workshop execution Supplied in protective transport box Single‑piece inspection pin FAQ What applications suit this gauge pin best? This measuring pin is intended for end‑dimension checks, go/no‑go verifications and fixture setting in workshop and light production environments; the Metav IndustryLine gauge pin with 15.84 mm diameter is particularly useful for bore and fit checks. Is the accuracy of ±0.002 mm guaranteed on delivery? The stated tolerance of ±0.002 mm describes the manufacture specification; the Metav IndustryLine gauge pin is produced to maintain this precision under normal handling and storage conditions. Which material is used for the pin and why does it matter? The pin is made from special steel, chosen for dimensional stability and wear resistance so that the reference diameter remains consistent during routine workshop use. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
15.85mm Test Pin Single 50mm Length Workshop Finish - Metav IndustryLine
Benefit from precise end‑measurement and robust workshop use with a compact 50 mm length and a ±0.002 mm manufacturing tolerance for consistent inspection results. Order the gauge pin directly via Metav Werkzeuge or ask our consultants for application advice. Gauge Pin M323.F85 — 15.85 mm diameter, 50 mm length (Metav IndustryLine) A gauge pin M323.F85 designed for precise end‑measure checks and routine inspection tasks in workshop and quality‑control environments. Precision tolerance ±0.002 mm Diameter 15.85 mm Length 50 mm Special steel construction Consistent precision that reduces rework and inspection uncertainty Manufactured to a tight ±0.002 mm tolerance, this pin provides a reliable reference for end‑measure checks and go/no‑go assessments. The compact 15.85 mm diameter and 50 mm overall length keep the component stiff under manual handling, which translates into reproducible readings and fewer measurement repeats. In practical terms, the pronounced manufacturing accuracy supports faster decision making on the shop floor: rejected parts are identified clearly, and acceptable components pass inspection without unnecessary delay. The combination of dimensional stability and workshop‑grade build quality suits frequent use in production inspection routines. Robust construction and handling tailored for workshop environments The component’s special steel composition ensures mechanical resilience during everyday inspection cycles. Its workshop‑oriented design balances durability with ease of handling: at approximately 0.1 kg, the pin is straightforward to position in measurement fixtures and comparator stands without adding excessive mass to the set‑up. The single‑piece format supports simple traceability and inventory control, while the compact dimensions make storage and transport within the workshop uncomplicated. Overall, the build quality enhances long‑term value by maintaining the reference geometry needed to keep tolerance chains aligned. Practical use cases and integration into inspection workflows This gauge pin is suited to routine end‑of‑line checks, dimensional spot checks on machined parts and insertion into fixture assemblies for quick verification. Where a concise, repeatable datum is required, the pin functions as a fast reference that integrates with optical comparators, micrometres and other bench metrology tools. Traceability is supported by the clear product identifiers and the robust construction that preserves calibration intervals. For workshops seeking a dependable measurement standard that performs under frequent use, the pin offers a dependable combination of stability and simplicity. For workshop procurement and technical guidance on the Metav IndustryLine gauge pin M323.F85, contact Metav Werkzeuge in Emmerich for tailored advice and ordering options Technical data Article number: M323.F85 GTIN: 4061905067334 Manufacturer: Metav IndustryLine Facts Diameter: 15.85 mm Length: 50 mm Tolerance: ±0.002 mm Weight: 0.1 kg Special features Single piece delivery Material: Special steel Workshop version Suitable for routine end‑measure checks FAQ What level of precision does this gauge pin provide? The gauge pin M323.F85 from Metav IndustryLine is manufactured to a tolerance of ±0.002 mm, providing a high level of repeatability for end‑measurement tasks. Is the pin suitable for frequent workshop use? Yes, the workshop version of this gauge pin is designed for regular inspection cycles and offers robust special‑steel construction for durability. How is the product identified for inventory and traceability? Identification is provided via the article number M323.F85 and GTIN 4061905067334, which allow straightforward tracking within quality systems. Can this pin be used as a reference in comparator or fixture setups? The pin’s compact 50 mm length and stable diameter make it suitable as a datum or reference in fixture and comparator arrangements. Is the gauge pin supplied as a single item or in sets? This listing describes a single‑piece gauge pin; the package contains one individual pin as specified. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
15.86mm Gauge Pin 50mm Length Workshop Version, Special Steel - Metav IndustryLine
Compact, highly accurate and workshop‑ready: the combination of 15.86 mm diameter, ±0.002 mm tolerance and special steel construction delivers reliable end‑dimension verification; order the test pin directly via Metav Werkzeuge or consult our advisers for application support Test pin M323.F86 — 15.86 mm diameter, 50 mm length (Metav IndustryLine) Test pin M323.F86 is a single inspection pin for precise end‑dimension checks in metrology and fixture checks Precision diameter 15.86 mm for end measurements Workshop grade construction in special steel Tight tolerance ±0.002 mm for reliable checks Single-piece supply for traceable handling Accurate end‑dimension control for production and inspection The M323.F86 is engineered for repeatable end‑dimension checks where small deviations matter. With a nominal diameter of 15.86 mm and a certified positional accuracy of ±0.002 mm, the pin is suited to fine gauging tasks, alignment checks and final inspection routines. The 50 mm effective length provides practical engagement in stacks, gauges or locating holes while keeping handling simple. Stated tolerances translate directly into fewer false rejects and higher process reliability in component verification. Durable workshop design that reduces downtime Built as a workshop‑grade tool from special steel, this inspection pin withstands frequent use in demanding shopfloor environments. The robust material choice maintains dimensional stability under repeated seating and handling, reducing the need for frequent replacements. At approximately 0.1 kg the component combines sufficient mass for stable seating with ease of installation into test rigs and jigs. The single‑piece supply supports traceable stock management in inspection departments and simplifies inventory handling. Integrates with inspection workflows and traceability systems The test pin fits into existing measurement and fixture setups with minimal adaptation. Its clear identification (GTIN and article number) supports procurement, storage and traceable deployment in quality systems. For application planning, tooling lists or fixture design the numerical data—diameter, length and tolerance—allow direct comparison with drawing limits and gauge specifications. Where specialised adaptation is required, technical teams may request application advice from Metav Werkzeuge to ensure the pin meets the intended inspection process Contact Metav Werkzeuge in Emmerich for tailored application advice and reliable supply of Metav IndustryLine inspection tools Technical data Article number: M323.F86 GTIN: 4061905067341 Manufacturer: Metav IndustryLine / Metav Werkzeuge GmbH Facts Diameter: 15.86 mm Length: 50 mm Tolerance: ±0.002 mm Weight: 0.1 kg EClass: 21170231 Special features Workshop execution Material: special steel Delivered as single piece Category: inspection pin (test pin) Intended use: end‑dimension verification FAQ What applications is this inspection pin suitable for? The inspection pin M323.F86 is intended for end‑dimension verification, alignment checks, gauge inserts and fixture locating where a 15.86 mm diameter pin with 50 mm length is required. Is the material specified for long‑term use in a workshop? Yes, the pin is manufactured from special steel and designed as a workshop‑grade component for repeated handling and seating in inspection setups. What level of dimensional accuracy can be expected? The stated accuracy is ±0.002 mm, making the pin suitable for precision checks where tight tolerances are required. How is the item identified for procurement and stock control? The test pin is supplied with GTIN 4061905067341 and article number M323.F86 to support catalogue management and traceability. Can the pin be used directly in standard gauges and fixtures? The pin’s dimensions and tolerances allow direct integration into many existing gauges and fixture designs; for specialised fixtures, consult Metav Werkzeuge for fitment advice. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
15.87mm Gauge Pin 50mm Length Workshop Finish - Metav IndustryLine
Robust workshop construction and a tight ±0.002 mm running tolerance provide dependable results for end‑dimension checks; the 15.87 mm diameter and 50 mm length ensure stable seating and repeatable positioning. Order the gauge pin directly via Metav Werkzeuge or ask our consultants for application advice. Gauge pin M323.F87 — workshop version, 15.87 mm dia, 50 mm length (Metav IndustryLine) The gauge pin M323.F87 is a single, workshop‑grade reference pin designed for precise end‑dimension checks, fixture alignment and assembly verification in inspection and production environments Workshop-ready construction Precision diameter 15.87 mm 50 mm length for stable positioning Dependable accuracy for repeatable inspection results The pin delivers a ±0.002 mm positional tolerance, which translates into highly repeatable reference points when checking end dimensions or aligning fixtures. In practice, this level of precision reduces rework and speeds throughput by providing a stable datum for comparative and go/no‑go checks. The stated tolerance is a measurable specification that enables straightforward integration into existing quality procedures, ensuring that measurement uncertainty is minimised when the pin is used as a seating or alignment element. Durable construction that suits the workshop environment Manufactured from special steel, this workshop‑version gauge pin combines surface hardness with corrosion resistance to withstand daily handling and intermittent contact with assemblies. The 50 mm overall length gives a secure engagement depth while the compact diameter supports tight fits in small bores and locating holes. Supplied for transport in a protective case, the pin is protected during storage and shipping, preserving the contact surfaces and maintaining the reference geometry for consistent use on the shop floor. Practical applications and handling guidance Designed for end‑dimension checks, fixture locators and assembly alignment, the pin functions as a straightforward reference pin in go/no‑go arrangements and as a locating element in jigging. Its nominal 15.87 mm diameter matches common bore sizes used for end‑mass checks and calibration aids; when paired with calibrated fixtures or plug gauges it streamlines inspection steps. Basic handling—store in the protective container, avoid dropping on hard surfaces and clean contact faces before use—preserves accuracy and extends service life for the tool. For procurement or to discuss how this Metav IndustryLine gauge pin fits specific inspection setups, contact Metav Werkzeuge for tailored advice and secure the item for your production process Technical data Article number: M323.F87 GTIN: 4061905067358 Label: Gauge pin, single, 15.87 mm dia, 50 mm length Facts Diameter: 15.87 mm Length: 50 mm Weight: 0.1 kg Accuracy / runout: ±0.002 mm Special features Material: special steel Workshop version Supplied in a protective transport case Single gauge pin for end‑dimension and fixture checks FAQ What tolerance can be expected from this gauge pin? The gauge pin M323.F87 offers a running tolerance of ±0.002 mm, suitable for precise locating and repeatable end‑dimension checks. Is the pin ready for immediate use on the shop floor? Yes, the workshop version arrives protected in a transport case and is ready for immediate use after a brief cleaning of the contact surfaces. Which materials is the M323.F87 intended to work with? The pin is a reference element rather than a cutting tool; it is compatible with fixtures and components made of common workshop materials where a 15.87 mm locating diameter is required. Can this pin be used for fixture alignment and assembly jigs? The pin is designed precisely for fixture alignment and assembly verification, providing a stable datum for locating parts during production. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
15.88mm Test Pin 50mm Length Workshop Version - Metav IndustryLine
The compact design and tight tolerance make this test pin a reliable reference for end‑measurement and fit verification; with ±0.002 mm accuracy and a 15.88 mm diameter it supports consistent quality control in production. Use the robust special steel construction and 50 mm length for repeatable probing tasks. Order the test pin directly via Metav Werkzeuge or ask our consultants if needed. Test pin, single — 15.88 mm diameter, 50 mm length (Metav IndustryLine) The Test pin, single 15.88 mm is a precision reference pin intended for end‑measurement, fit checks and locating tasks in workshop and inspection environments. Workshop version for robust daily use Diameter 15.88 mm, nominal reference pin Length 50 mm for standard probing tasks Accuracy ±0.002 mm for precise verification Consistent measurement certainty for production control A tight tolerance of ±0.002 mm ensures the pin performs as a trustworthy reference in routine inspection work. The high precision reduces uncertainty when checking mating parts, bore diameters or assembly fits; this rational advantage speeds up decision‑making on the shop floor and lowers the risk of downstream rework. Where repeatable go/no‑go checks are required, the probe form factor supports straightforward comparison against drawing tolerances. Durable workshop execution that withstands daily use Constructed from special steel and specified as a workshop version, the probe balances wear resistance with dimensional stability. The 50 mm overall length and 15.88 mm shank diameter are suitable for mounting in fixtures or using as a handheld gauge pin during setup and first‑off inspections. The robust material choice and slim geometry support frequent handling while maintaining the geometric integrity needed for reliable reference measurements. Practical integration into inspection routines Designed for simple, effective use, this reference pin integrates easily into manual gauging and fixture setups. The compact form factor assists in tight assembly spaces and the controlled tolerance makes it compatible with dial gauges, inspection benches and tactile checks. Supplied as a single probe (SKU M323.F88), it is intended to complement existing measuring sets and to serve as a stable benchmark for repetitive dimensional verifications. For precise end‑measurement and fit verification, choose the Metav IndustryLine test pin M323.F88 — contact Metav Werkzeuge for product guidance and availability at info@metav-werkzeuge.com or by phone on +49 2822 7131930 Technical data SKU: M323.F88 GTIN: 4061905068102 Numbers / Core technical data Diameter: 15.88 mm Length: 50 mm Accuracy: ±0.002 mm Weight: 0.1 kg Special features / Designs Material: Special steel Version: Workshop execution Category: Test pin / gauge pin FAQ What tolerance does the test pin offer? The test pin M323.F88 (Metav IndustryLine test pin) is specified with an accuracy of ±0.002 mm, suitable for precise end‑measurement and fit checks. Which material is the pin made from? The test pin M323.F88 is manufactured from special steel, providing good wear resistance for workshop use. What are the exact dimensions of the probe? The test pin M323.F88 has a diameter of 15.88 mm and a length of 50 mm; its weight is 0.1 kg. Is the pin suitable for gauging bores and fits? Yes. The probe geometry and tight tolerance of the test pin M323.F88 make it suitable for go/no‑go checks, locating and basic bore verification tasks. How can the probe be used in inspection routines? The test pin M323.F88 can be mounted in fixtures or used manually as a reference for tactile checks, pairing well with dial gauges and simple inspection fixtures for reproducible checks. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
15.89 mm Gauge Pin, Single, 50 mm Length Workshop Version - Metav IndustryLine
Take advantage of industrial-grade precision (±0.002 mm) combined with a compact 15.89 mm diameter and a 50 mm length for reliable inspection and fixture tasks; order the gauge pin directly via Metav Werkzeuge or consult our specialists for application advice. Gauge pin, single, 15.89 mm Ø — Metav IndustryLine workshop version Gauge pin, single, 15.89 mm Ø, length 50 mm designed for precise end-measurement and component verification in workshop and production environments Gauge pin Ø 15.89 mm Length 50 mm for confined spaces Tolerance ±0.002 mm industrial grade Workshop version with robust finish Engineered accuracy for routine inspection The compact inspection pin is manufactured from special steel and finished for workshop use, delivering a declared tolerance of ±0.002 mm. This level of control makes the component suitable for comparative checks, insertion gauges and final acceptance routines where repeatability matters. The 15.89 mm nominal diameter is held to tight limits, reducing clearance variation in fixture interfaces and ensuring consistent positional reference during short-cycle inspections. The declared accuracy supports traceable quality assurance within standard workshop processes. Compact form that fits tight assemblies A 50 mm effective length provides access into shallow bores and narrow recesses while keeping the handling ergonomically simple. The short profile reduces bending risk under manual placement and eases alignment in jigs and test fixtures; the workshop version finish balances wear resistance with ease of integration. For production settings where measurement throughput and physical accessibility are equally important, the pin’s geometry offers a practical compromise between reach and stiffness, enabling quick checks without complex fixturing. Designed for integration and repeatable results Supplied as a single inspection pin, the item is intended for direct inclusion in routine measurement sets and handheld verification tools. The combination of special steel and precise finishing reduces surface deviations that can influence fit checks and repeat readings. For quality managers looking to standardise go/no-go routines or to define reference points in assembly stations, the pin acts as a compact, reliable datum. Documentation such as GTIN and SKU allow straightforward inventorying and traceability in procurement and inspection records. Contact Metav Werkzeuge in Emmerich for product matching, compatibility checks or to secure the Metav IndustryLine gauge pin with 15.89 mm diameter for immediate workshop use Technical data SKU: M323.F89 GTIN: 4061905068270 Category: Messstifte Diameter: 15.89 mm Length: 50 mm Tolerance: ±0.002 mm Weight: 0.1 kg Material: Special steel Delivery: single gauge pin Version: Workshop execution FAQ What level of precision does this gauge pin provide? The gauge pin provides an industrial precision of ±0.002 mm; the Metav IndustryLine inspection pin is therefore suitable for repeatable dimensional checks and fixture alignment. Which material is used for this inspection pin? This Metav IndustryLine pin is made from special steel, offering a balanced combination of hardness and surface stability for frequent workshop use. Is the 50 mm length suitable for confined bores? Yes—the 50 mm length of the gauge pin gives sufficient reach for shallow bores and narrow assembly gaps while maintaining rigidity for reliable checks. How is the product supplied and identified? The item is supplied as a single gauge pin and can be identified by SKU M323.F89 and GTIN 4061905068270 for ordering and inventory control. Can this pin be used as a reference in fixture assemblies? The workshop-grade finish and tight diameter tolerance make this Metav IndustryLine gauge pin suitable as a positional reference in jigs and small fixtures where a compact datum is required. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
15.8mm Gauge Pin, Workshop Version, 50mm Length - Metav IndustryLine
Take advantage of a compact, workshop-grade gauge pin that combines special-steel durability with an accuracy of ±0.002 mm for reliable end‑measurements; order directly via Metav Werkzeuge or consult our advisers for application advice. Gauge pin, single, 15.8 mm × 50 mm (Metav IndustryLine) — special steel, ±0.002 mm The gauge pin, single, 15.8 mm × 50 mm is a workshop execution reference pin designed for precise end‑measurements and fit verification in small parts and assembly checks. Workshop-grade special steel construction High positional accuracy ±0.002 mm 50 mm overall length for end‑measurement applications Supplied in protective transport box Precision where small tolerances matter This single gauge pin is manufactured from special steel and finished to deliver a repeatable positional accuracy of ±0.002 mm, making it suitable for quality control tasks where tight clearances are critical. The nominal diameter of 15.8 mm provides a precise reference for bore and fit checks; the 50 mm overall length yields enough engagement depth for stable seating while remaining easy to handle. In practice, that accuracy helps reduce rework by ensuring mating parts meet specification before assembly. Compact design for small‑component workflows Classified in the micro range (10–100 mm), this test pin is optimised for fine‑mechanical and general workshop use where reach and stiffness must be balanced. The workshop‑grade build and the short shank geometry keep the pin torsion‑resistant and simple to position in jigs or fixtures. As a result, measurement cycles are faster and handling is straightforward, which benefits bench technicians and inspection staff who need efficient, dependable gauges for repetitive checks. Practical handling, protection and traceability Delivered in a protective transport box, the pin arrives ready for safe storage and transport between workstations. The compact mass (approx. 0.1 kg) makes the gauge easy to manoeuvre and seat without fatigue, while the robust material finish resists routine wear in a production environment. Clear identification via the supplied SKU and GTIN supports inventory control and traceability in quality systems, assisting shops that require consistent reference artefacts for audit and calibration planning. Contact Metav Werkzeuge for specific application guidance on this Metav IndustryLine gauge pin and to arrange direct procurement or tailored packaging options via info@metav-werkzeuge.com or +49 2822 7131930 Technical data Article number: M323.F80 GTIN: 4061905071133 Manufacturer: Metav IndustryLine Facts Diameter: 15.8 mm Overall length: 50 mm Mass: 0.1 kg Positional accuracy: ±0.002 mm Special features Material: Special steel Delivery: Transport/protective box included Workshop execution (werkstatt‑ausführung) FAQ Is this pin suitable for bore go/no‑go checking? The gauge pin is intended as a precise reference for bore and fit verification; the 15.8 mm diameter and ±0.002 mm specification make it suitable for dimensional checking and seating tests. Can the pin be used in a fixture for repeated measurements? Yes, the workshop execution and special‑steel construction are designed for repeated seating in jigs and fixtures where stable reference geometry is required. Does the item include protective packaging for transport? Delivery includes a protective transport box to safeguard the pin during storage and transfer between workstations. What makes this Micro‑range pin different from longer gauges? Micro‑range pins combine compact stiffness with precise control for small parts; at 50 mm length this pin balances engagement depth with low deflection for accurate local checks. Is traceability information provided with the product? The product is supplied with clear identification (SKU and GTIN) to support inventory and traceability systems in inspection processes. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
15.91mm Gauge Pin Length 50mm Workshop Version - Metav IndustryLine
Take advantage of a compact, workshop‑ready measuring solution that combines high repeatability with a tight tolerance of ±0.002 mm, ensuring reliable end‑dimension checks and smooth inspection routines. Order the gauge pin directly via Metav Werkzeuge or consult our team for specification advice. Gauge pin M323.F91 – single gauge pin Ø 15.91 mm, length 50 mm (Metav IndustryLine) A gauge pin, single, Ø 15.91 mm, length 50 mm engineered for precise diameter verification and end‑measurement tasks in workshop and production inspection. Single gauge pin Ø 15.91 mm Tolerance ±0.002 mm for repeatable checks Length 50 mm for compact measuring setups Consistent diameter verification for efficient inspection This cylindrical gauge pin is designed to deliver reproducible results when verifying hole diameters, plug fits or final dimensions in small assemblies. The ±0.002 mm tolerance provides a clearly defined acceptance criterion that simplifies go/no‑go decisions on the shop floor and reduces time spent on iterative checks. By using a hardened, dimension‑stable cylindrical master, inspection cycles become faster and less prone to operator variation, which improves throughput and reduces scrap rates. Robust workshop design that stands up to daily use Manufactured from special steel and supplied in a workshop configuration, the component is made for the practical demands of frequent handling and immediate measurement tasks. The compact 50 mm length makes it easy to position in tight fixtures and simplifies storage in existing tool kits. The material choice balances wear resistance with precision: the surface finish and core hardness maintain cylindrical integrity over repeated use, preserving accuracy and minimising rework. Easy integration into existing quality processes As a single, well‑defined master gauge, the item integrates seamlessly into established inspection sequences and fixtures. Traceable identification (SKU M323.F91, GTIN 4061905068294) facilitates inventory control and documentation for quality records. The physical simplicity of a gauge pin means no special interfaces are required; it complements calipers, micrometres and plug assemblies to build a pragmatic, layered measurement strategy that prioritises repeatable outcomes. Practical advantages for machinists and inspection staff The compact format reduces handling time during batch checks and supports quick functional testing at assembly stations. With a focus on objective measurement capability rather than interpretive assessment, the pin helps standardise inspection across operators and shifts. The workshop‑oriented build encourages day‑to‑day robustness while retaining the fine dimensional control necessary for small tolerance components. For specification support or to confirm fit with existing gauges and fixtures, contact Metav Werkzeuge for personalised guidance and reliable supply from Emmerich. Technical data SKU: M323.F91 GTIN: 4061905068294 Brand: Metav IndustryLine Dimensions & core technical data Diameter: 15.91 mm Length: 50 mm Tolerance / accuracy: ±0.002 mm Weight: 0.1 kg Special features & materials Material: special steel Version: workshop execution Category: single gauge pin Intended use: end‑dimension checks FAQ What is the intended use of this gauge pin? The gauge pin M323.F91 is intended for precise diameter verification and end‑measurement tasks in workshop and production inspection, providing a simple master for go/no‑go assessment. Is the tolerance suited to fine mechanical work? Yes; the ±0.002 mm tolerance makes the gauge pin suitable for fine mechanical and precision inspection tasks where clear acceptance limits are required. Which material is used for the pin and why does it matter? The pin is made from special steel, chosen for wear resistance and dimensional stability so that the pin retains its accuracy during frequent use. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
15.92mm Gauge Pin, 50mm Length, Workshop Version, Special Steel, Calibrated Delivery in Case - Metav IndustryLine
Take advantage of a compact inspection aid that combines a 15.92 mm controlled diameter with a 50 mm handling length and a certified workshop design for reliable end‑measure checks; the tight ±0.002 mm positional tolerance supports consistent acceptance tests. Order the item directly via Metav Werkzeuge or consult the Metav team for application advice and availability. Metav IndustryLine gauge pin M323.F92 — 15.92 mm diameter, 50 mm length A single gauge pin of 15.92 mm diameter and 50 mm length intended for precise end‑measure and fitting checks in workshop and inspection routines 15.92 mm diameter, 50 mm length Special steel for wear resistance Positional accuracy ±0.002 mm Consistent inspection results through fine tolerance control The compact design delivers measurable benefits for routine acceptance checks. With a 15.92 mm nominal diameter and a declared positional tolerance of ±0.002 mm, this pin is suited to dimensional verification where repeatability matters. The narrow tolerance reduces ambiguity during go/no‑go assessments and supports faster decision making in production lines. As a standardised inspection element, the component minimises test variation and helps to lower rework rates, which improves overall throughput and quality metrics. Built for everyday workshop use with durable materials Constructed from special steel and specified as a workshop variant, the pin resists wear under frequent handling and insertion cycles. The 50 mm length provides a practical balance between grip and immersion depth, simplifying handling on benches and in fixtures. Robust material choice prolongs service life and preserves the measured diameter over many cycles, meaning fewer replacements and steadier measurement baselines for maintenance teams and quality engineers. Simple integration into quality workflows and fixture systems The unit is offered as a single, dedicated gauge pin (SKU M323.F92), making it straightforward to allocate to specific jigs, test benches or inspection kits. Because the component is a single‑purpose measuring element, it integrates cleanly with existing acceptance procedures and can be recorded in measurement logs as a repeatable reference. Procurement through a Europe‑based supply channel reduces lead times and supports consistent stock levels for line‑side inspection needs. Enquire with Metav Werkzeuge in Emmerich for technical clarification, sample availability or to reserve the M323.F92 gauge pin for your inspection kit — email info@metav-werkzeuge.com or call +49 2822 7131930 for prompt assistance. Technical data Article number: M323.F92 GTIN: 4061905068300 Label: Prüfstift, einzeln, 15,92 mm Länge 50 mm Dimensions & accuracy Diameter: 15.92 mm Length: 50 mm Positional accuracy: ±0.002 mm Weight: 0.1 kg Materials & features Material: Special steel Version: Workshop execution Category: Gauge pin (Messstifte) FAQ What is the exact diameter and length of the gauge pin? The gauge pin has a nominal diameter of 15.92 mm and a handling length of 50 mm; this format suits common end‑measure and fitting checks. How precise is the M323.F92 during inspection tasks? The M323.F92 is specified with a positional accuracy of ±0.002 mm, delivering repeatable results for acceptance testing and dimensional verification. Which material is used for the pin and why does it matter? The pin is made from special steel, chosen for wear resistance and dimensional stability under frequent use, which preserves nominal diameter over many insertion cycles. Can this gauge pin be used in fixtures and jigs? Yes, the single‑pin format and standardised diameter make M323.F92 simple to integrate into existing fixtures, test benches and inspection kits. Is the component suitable for routine workshop inspection? The workshop execution and practical 50 mm length make this gauge pin well suited to everyday inspection routines and bench‑level quality control. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
15.93mm Gauge Pin 50mm Length Workshop Version - Metav IndustryLine
Take advantage of workshop-grade robustness combined with calibrated precision for consistent end-dimension checks: a 15.93 mm diameter reference pin with ±0.002 mm tolerance and a 50 mm length that stabilises setup and inspection workflows. Order the gauge pin directly via Metav Werkzeuge or consult our specialists for application advice. Gauge pin, single — 15.93 mm diameter, 50 mm length (Metav IndustryLine) Gauge pin, single, 15.93 mm diameter, 50 mm length is a compact reference pin for precision checking of bore and end dimensions in workshop environments and fixture setup 15.93 mm diameter for precise plug checks Tolerance ±0.002 mm for repeatable results Workshop version in special steel Precision that removes doubt in everyday inspections The gauge pin delivers a measurable improvement in process reliability by combining a defined 15.93 mm diameter with a narrow ±0.002 mm tolerance. As a hardened reference element, it functions as a simple yet robust reference standard for go/no‑go checks, gauge verification and setup control. The specification limits the measurement uncertainty introduced at the operator level and helps to maintain statistical process control in production environments, reducing rework and inspection time. Built for the workshop — durable and simple to handle Produced as a workshop version from special steel, the pin resists wear during repetitive checks and can be handled comfortably in routine tasks thanks to its 50 mm overall length. The compact form factor permits quick insertion into bores, checking alignment in fixtures and transferring dimensional references between stations. The material choice and execution ensure long service life on the shop floor while preserving the dimensional integrity required for repeatable quality control. Integrates with inspection and setup workflows This single gauge pin supports efficient fixture setting, confirmation of end dimensions and rapid verification during batch work. Traceability is simple: the item is available with a clear product code (M323.F93) and GTIN for inventory management. Using a defined gauge pin as a control element shortens inspection cycles and provides immediate pass/fail information, which in turn streamlines decision making on the production line and reduces downtime. For workshop-ready precision from Metav IndustryLine, contact Metav Werkzeuge for technical advice, sample pins or ordering information via info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: M323.F93 GTIN: 4061905068317 Category: Messstifte Facts Diameter: 15.93 mm Length: 50 mm Tolerance: ±0.002 mm Weight: 0.1 kg Special features Single gauge pin, workshop execution Material: special steel Intended use: end-dimension and bore checking Type designation: Gauge pin, single, 15.93 mm, 50 mm length FAQ What tolerance does this gauge pin offer? The gauge pin (Gauge pin, single, 15.93 mm diameter, 50 mm length) is specified with a tolerance of ±0.002 mm, suitable for precise workshop checks. Is the pin suitable for repeated plug checks on production lines? Yes. The workshop execution and special steel construction make the pin (M323.F93) appropriate for repetitive use in production and setup routines. Can this pin be used for fixture alignment and gauge setting? The 50 mm length and rigid design allow the pin to serve as a reliable reference for fixture alignment and gauge setting tasks. How is the product identified for inventory control? The item is listed under GTIN 4061905068317 and Article number M323.F93 to simplify stock management and procurement. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
15.94mm Test Pin, Single, 50mm Length, Workshop Version - Metav IndustryLine
Take advantage of the combination of workshop‑grade durability, exact Ø 15.94 mm sizing and a tight ±0.002 mm tolerance for reliable end‑measurement results; order the gauge pin directly via Metav Werkzeuge or ask our consultants if needed. Gauge Pin M323.F94 — Single inspection pin, Ø 15.94 mm, Length 50 mm (Metav IndustryLine) The Gauge Pin M323.F94 is a single, precision inspection pin designed for end‑measure checks, fixture set‑up and alignment tasks in workshop environments. Single gauge pin Ø 15.94 mm, length 50 mm High precision tolerance ±0.002 mm Workshop version in special steel Precision that speeds up inspection High repeatability and defined limits make this gauge pin a practical choice where quick, verifiable decisions are required on the production floor. The nominal Ø 15.94 mm dimension together with the ±0.002 mm tolerance ensures results that are directly comparable across shifts and operators, reducing time spent on rework. The compact nominal form simplifies handling during serial checks and shortens the measurement loop between locating, measuring and documenting, which delivers a measurable gain in throughput. Built for workshop use and protected in transit Manufactured in special steel, the pin is specified as a workshop execution to withstand the knocks and handling typical of everyday use. The 50 mm length provides a stable contact surface while remaining easy to position in fixtures or between datum faces. Delivery in a dedicated case protects the measurement surface during transport and storage; this minimises the risk of nicks or contamination that would otherwise compromise measurement certainty. The modest weight supports safe one‑hand use and straightforward insertion into assemblies. Easy integration into inspection routines and quality workflows Intended for end‑measurements and alignment checks, the inspection pin fits naturally into go/no‑go and positional verification processes. Its defined geometry supports automated and manual checking alike, helping to standardise inspection steps across production cells. Choosing a tool from Metav IndustryLine adds the reassurance of a supplier that places emphasis on accessibility and reliable supply for workshops and small‑scale industry alike; the pragmatic design helps teams maintain traceable, auditable measurement records without complicated set‑ups. Discuss the Metav IndustryLine gauge pin with Metav Werkzeuge for a tailored recommendation on how M323.F94 can support production checks and fixture verification at your site; Metav Werkzeuge will advise on availability and delivery from Emmerich. Technical Data SKU: M323.F94 GTIN: 4061905068324 Brand: Metav IndustryLine ECLASS: 21170231 Category: Gauge pins (Messstifte) Measurements & Weight Diameter: 15.94 mm Length: 50 mm Tolerance: ±0.002 mm Weight: 0.1 kg Materials & Features Material: Special steel Workshop execution Delivered in transport case (plastic or wooden) Application: End measurements and fixture checks Story trigger: end measurements FAQ What are the exact dimensions and tolerance of this inspection pin? The Gauge Pin M323.F94 (Metav IndustryLine) has a nominal diameter of 15.94 mm, a length of 50 mm and a tolerance of ±0.002 mm. Is the pin suitable for end‑measurements and fixture set‑ups? Yes, the design and geometry of this inspection pin make it suitable for end‑measurements, alignment and fixture checks in workshop and inspection routines. How is the item packaged for transport? The inspection pin is supplied in a transport case (plastic or wooden) to protect the measuring surface during shipping and handling. What material is used and what does that mean for durability? Made from special steel, the pin is specified for workshop use to provide robustness against handling and to maintain dimensional stability under normal workshop conditions. Which brand delivers this pin and how is it identified? This inspection pin is offered by Metav IndustryLine and is available under SKU M323.F94 with GTIN 4061905068324. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
15.95mm Gauge Pin 50mm Length Workshop Version - Metav IndustryLine
Compact accuracy for inspection tasks: the 15.95 mm diameter, 50 mm length and a tight ±0.002 mm tolerance combine to deliver repeatable, high‑precision checks in workshop environments; order the M323.F95 gauge pin directly via Metav Werkzeuge or ask our consultants if needed. M323.F95 — Gauge pin, 15.95 mm diameter · 50 mm length (Metav IndustryLine) The M323.F95 is a single precision gauge pin designed for end‑measurement and fit verification in inspection and assembly tooling. High machining tolerance ±0.002 mm Diameter 15.95 mm for precise fits 50 mm hardened length for stable positioning Workshop execution for daily use Consistent accuracy for repeatable inspection results Precision is the primary benefit of this inspection pin: with a certified tolerance of ±0.002 mm, the component supports reliable go/no‑go checks and dimensional verification where small deviations matter. The nominal diameter of 15.95 mm is ideal for matching tight bore fits and verifying mating parts; by reducing measurement scatter, process control becomes more predictable and corrective action less frequent. This measurable performance is particularly relevant in quality assurance loops where traceable and repeatable checks cut rework and scrap. Durable construction that withstands workshop routines Built in a workshop execution, the pin pairs robustness with practical handling. Manufactured from special steel, the item resists wear under repeated insertions and offers a stable contact surface for gauges and checking fixtures. The 50 mm length provides sufficient insertion depth for secure seating in many fixturing situations while remaining compact enough for handheld inspection tools. The resulting balance of durability and manoeuvrability reduces downtime for replacements and keeps throughput steady on the shop floor. Simple integration into inspection workflows The single‑item format suits bespoke inspection setups where individual pins are selected for specific bores. At 0.1 kg, the item is light to position yet substantial enough to avoid accidental displacement during checks. Identifiers such as SKU M323.F95 and the GTIN allow unambiguous procurement and inventory tracking, simplifying replenishment and traceability. The combination of defined dimensions and a narrow tolerance window makes the pin an efficient tool for both routine quality checks and final assembly verification. Choose the Metav IndustryLine M323.F95 for consistent, workshop‑ready precision — supply and advice available from Metav Werkzeuge in Emmerich; email info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: M323.F95 GTIN: 4061905068331 Category: Gauge pins Manufacturer: Metav IndustryLine Facts Diameter: 15.95 mm Length: 50 mm Tolerance: ±0.002 mm Weight: 0.1 kg Special features Material: Special steel Workshop execution Single item FAQ What tolerance does this gauge pin offer? The M323.F95 gauge pin is specified with a ±0.002 mm tolerance suitable for fine inspection tasks and tight fit checks. Which measurements is the pin intended for? This pin is intended for end‑measurement and fit verification of bores and mating parts where a 15.95 mm diameter reference is required. Is the M323.F95 a single item or part of a set? The item is supplied as a single precision gauge pin, listed under SKU M323.F95 for clear identification. How should the pin be used in an inspection setup? Use the pin as a go/no‑go or reference mandrel for verifying bore sizes and seating conditions during assembly or quality control procedures. Metav IndustryLine: Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
15.96mm Gauge Pin 50mm Length Workshop Finish, Special Steel - Metav IndustryLine
The combination of a workshop‑grade build, a ±0.002 mm tolerance and a compact 50 mm length provides reliable, repeatable end‑measure checking with minimal setup time; order the gauge pin directly via Metav Werkzeuge or contact Metav’s consultants for application advice. M323.F96 gauge pin (single) — 15.96 mm diameter, 50 mm length — Metav IndustryLine The M323.F96 gauge pin is a workshop‑grade inspection pin designed for fast end‑measure verification and go/no‑go checks in production and inspection workflows. Workshop‑grade construction Diameter 15.96 mm for end‑measure checks Length 50 mm, stable handling Tolerance ±0.002 mm for tight fits Improve pass/fail certainty in routine checks A compact inspection pin with a 15.96 mm nominal diameter and a declared ±0.002 mm variation brings measurable benefits to production control. The small tolerance reduces ambiguity when assessing hole sizes or fit dimensions, which lowers the rate of false rejects and prevents downstream rework. Used as a reference for end‑measure verification, this pin supports consistent decision‑making during quality checks and aligns inspection outcomes with process tolerances. Built for workshop handling and repeatability Constructed from special steel and presented as a workshop‑grade tool, the pin’s 50 mm shank length gives a comfortable handling profile while maintaining rigidity during insertion. The compact mass (approx. 0.1 kg) helps to reduce user fatigue in repetitive checks and makes the pin straightforward to position in bore inspections. The material selection and finish are chosen to withstand everyday workshop conditions, providing sustained precision across multiple cycles. Practical integration into inspection routines The single‑piece format is suited to end‑measure and fit control tasks where clear, reproducible results are required. As a simple, tangible reference gauge, the pin works well for quick size verification during setup, in‑process sampling and final inspection of end‑masses. Its compact size makes it easy to include in inspection kits or fixed gaging fixtures, enabling stable measurement points without complex instrumentation. For systems that require traceability or set checks, the product’s SKU and identifiers allow straightforward documentation in quality records. For reliable end‑measure control, request the Metav IndustryLine M323.F96 gauge pin via Metav Werkzeuge — technical consultants in Emmerich are available to advise on integration and to confirm suitability for specific inspection tasks (info@metav-werkzeuge.com / +49 2822 7131930) Technical Data SKU: M323.F96 GTIN: 4061905068348 Brand: Metav IndustryLine Category: Gauge pins Facts Diameter: 15.96 mm Length: 50 mm Tolerance: ±0.002 mm Weight: 0.1 kg Special features Material: Special steel Workshop version Single gauge pin delivery eClass: 21170231 FAQ What is the M323.F96 gauge pin used for? The M323.F96 is intended for end‑measure verification and simple go/no‑go checks in production and inspection, serving as a tangible reference for hole diameter and fit control. How precise is this inspection pin? The gauge pin is specified with a variation of ±0.002 mm, making it suitable for tight‑fit checks and repeatable pass/fail decisions on critical diameters. Is the gauge pin delivered as a set or single piece? This article is supplied as a single gauge pin; the product designation is M323.F96 and it belongs to the Metav IndustryLine range. Which materials and components is the pin intended to check? The pin verifies bore sizes and fit dimensions regardless of substrate; it is used to assess the final measurement state of components made from metals, plastics and other common workshop materials. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
15.97mm Gauge Pin 50mm Length Workshop Version, Special Steel - Metav IndustryLine
Take advantage of the combination of high repeatability, compact dimensions and workshop-grade robustness for reliable end‑measurement tasks; order the gauge pin directly via Metav Werkzeuge or consult our specialists for application advice. M323.F97 gauge pin — 15.97 mm diameter, 50 mm length (Metav IndustryLine) M323.F97 gauge pin is a single precision plug intended for end‑measurement and alignment tasks in workshop environments Workshop-grade execution Diameter 15.97 mm, tolerance ±0.002 mm Length 50 mm, solid special‑steel construction Precision where it matters The gauge pin is engineered for consistent end‑measurements and fits verification. With a nominal diameter of 15.97 mm and a specified runout/fitting tolerance of ±0.002 mm, this precision pin supports tight assembly checks and calibration routines that demand repeatable results. The compact length and stable geometry reduce measurement scatter, making the component suitable as a reference mandrel in small‑batch inspection or as a go/no‑go datum for jig setup. Robust workshop performance Designed as a workshop execution product, the pin combines a hardwearing finish with a geometry that resists deformation during frequent handling. The 50 mm length gives ample engagement depth for many practical checks while remaining easy to position by hand or in simple fixtures. Its construction minimises the need for frequent replacement, improving throughput by lowering downtime for tool changes and rework. Material choice and longevity Made from special steel, the pin balances surface hardness with fatigue resistance for sustained dimensional stability under repeated insertion and withdrawal. The material choice offers corrosion resistance comparable to standard workshop alloys and is suitable for routine cleaning and light lubrication regimes. Traceable identifiers such as the SKU M323.F97 and GTIN 4061905068355 assist in inventory control and quality documentation. Practical applications in the production flow Compact and precise, the plug works well for end‑dimension checks, alignment of small housings, and as a reference for handheld comparators. Its tolerance makes it appropriate for final inspection steps where deviations beyond a few micrometres are critical. The single‑piece supply simplifies logistics for one‑off tasks or when a dedicated reference pin is required on a specific machine or fixture. For detailed application advice or to request immediate dispatch of the M323.F97 gauge pin from Metav IndustryLine, contact Metav Werkzeuge in Emmerich for expert guidance and reliable supply. Technical data SKU: M323.F97 GTIN: 4061905068355 Label: Prüfstift, einzeln, 15,97 mm Länge 50 mm Manufacturer: Metav IndustryLine Core specifications Diameter: 15.97 mm Length: 50 mm Accuracy / tolerance: ±0.002 mm Weight: 0.1 kg Special features Workshop‑grade execution Material: special steel Delivery: single piece FAQ What is the exact diameter and tolerance of this plug? The plug has a nominal diameter of 15.97 mm with a tolerance of ±0.002 mm as specified for the M323.F97 gauge pin. Is the product supplied as a single item or in sets? This article is supplied as a single precision gauge pin, described as a single piece in the technical data. Which material is used for the pin and how durable is it? The pin is manufactured from special steel, chosen for dimensional stability and resistance to wear under frequent use. For which inspection tasks is the pin most suitable? The gauge pin is intended for end‑measurement checks, alignment, and small‑component fit verification where high repeatability is required. How can the part be identified within a stock system? Identification is possible via SKU M323.F97 and GTIN 4061905068355, which are listed in the product data. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
15.98mm Gauge Pin Length 50mm Workshop Finish - Metav IndustryLine
Take advantage of a workshop-ready gauge pin that pairs high repeatability with tight tolerance control and robust material choice to streamline inspection tasks; order directly via Metav Werkzeuge or consult our specialists for application advice. Gauge pin M323.F98 — Ø 15.98 mm, 50 mm length (Metav IndustryLine) A gauge pin for precise end‑measure checks and diameter verification in workshop environments, supplied as a single test pin. Precision tolerance ±0.002 mm Diameter Ø 15.98 mm 50 mm length for bore and seat checks Workshop version for everyday use Consistent, measurable precision for routine inspections The M323.F98 is built for consistent dimensional checks where small deviations matter. With an accuracy of ±0.002 mm, the pin reduces measurement uncertainty and helps maintain production tolerances across repetitive checks. The stated tolerance should be read as the maximal permissible deviation under standard measurement conditions; in practice this supports faster go/no‑go decisions and reduces downstream rework. The compact form and single‑piece supply suit bench testing and quick verification tasks without extras. Practical design that speeds up workflow A clearly defined diameter of Ø 15.98 mm and a 50 mm overall length make this inspection pin ideal for checking bores, seats and end faces where a stable datum is required. Manufactured from special steel, the component provides mechanical integrity for regular use in workshop settings and can be handled simply with standard toolroom procedures. The straightforward geometry shortens set‑up time on gauges and fixtures, enabling technicians to keep inspection loops short and machine downtime low. Workshop grade: robustness and application clarity Designed as a workshop version, the test pin balances precision with everyday resilience. The single‑piece delivery simplifies inventory and replacement planning for maintenance teams and inspection benches. Where visual or tactile assessment is used, the defined diameter aids tactile feel checks and ensures a reliable physical reference. For organisations seeking objective measurement evidence, the pin supports documented inspection routines and repeatable sampling in batch production. For repeatable bore and seat verification choose the Metav IndustryLine M323.F98 gauge pin — order via Metav Werkzeuge or request tailored application guidance from our Emmerich team. Technical data Article number: M323.F98 GTIN: 4061905069192 Brand: Metav IndustryLine Facts Diameter: 15.98 mm Length: 50 mm Accuracy: ±0.002 mm Weight: 0.1 kg Special features Workshop version Material: Special steel Single piece supply Category: Gauge pins FAQ What is the dimensional tolerance of this gauge pin? The gauge pin M323.F98 offers an accuracy of ±0.002 mm, suitable for fine inspection work and tight tolerance verification. For which applications is this pin intended? This inspection pin is intended for end‑measure checks, bore and seat verification, and other routine diameter controls in workshop environments. What material is the pin made from? The pin is manufactured from special steel, providing mechanical strength for regular use at inspection benches. Is the product delivered as a single item or in sets? The M323.F98 is supplied as a single test pin, simplifying replacement and stock management. Can this pin be used as a reference in fixture set‑ups? Yes, the defined diameter and robust form make it suitable as a physical reference in gauge fixtures and quick verification jigs. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
15.99mm Test Pin 50mm Length Workshop Version - Metav IndustryLine
Take advantage of the combination of workshop robustness, tight dimensional accuracy and straightforward handling to keep inspection and setup cycles efficient; order the part directly via Metav Werkzeuge or consult our specialists for application advice. Gauge pin M323.F99 — single inspection pin, 15.99 mm diameter, 50 mm length (Metav IndustryLine) A Gauge pin M323.F99 designed as a precise reference for end‑dimension verification and fixture alignment in workshop metrology Precision tolerance ±0.002 mm Nominal diameter 15.99 mm 50 mm overall length Special steel workshop version Consistent accuracy for dimensional checks The gauge pin provides a reproducible reference diameter with a stated tolerance of ±0.002 mm, ensuring reliable pass/fail evaluation when measuring end dimensions or verifying bore sizes. With a nominal diameter of 15.99 mm, the component serves as a calibrated reference for inspection benches and fixture set‑ups where repeatability matters. The declared accuracy corresponds to fine mechanical tolerances and reduces uncertainty in go/no‑go assessments, supporting concise documentation of measurement results. Practical design that speeds up setup and inspection A compact 50 mm length combines sufficient engagement for stable seating with convenient handling during rapid checks. The 50 mm overall length gives immediate tactile feedback when inserted into a bore or locating feature, shortening cycle time for routine gauges and reducing handling errors. Constructed from special steel, the pin resists wear in workshop environments and maintains dimensional integrity under regular use, which supports lower maintenance intervals and predictable inspection throughput. Workshop‑grade reliability and supply transparency Built as a workshop execution item, this inspection pin is intended for everyday metrology tasks and fixture calibration. The sturdy material choice and tight tolerance make it suitable as a repeatable reference for assembly control or end‑dimension verification. Stocked and distributed by Metav IndustryLine, the item is traceable with SKU M323.F99 and GTIN 4061905069208, which simplifies procurement and inventory management for production and quality departments. For reliable workshop inspection standards, contact Metav Werkzeuge to reserve the Metav IndustryLine gauge pin M323.F99 or to discuss suitable reference parts for specific applications Technical data SKU: M323.F99 GTIN: 4061905069208 Description: Single gauge pin, 15.99 mm diameter, 50 mm length Core dimensions Diameter: 15.99 mm Length: 50 mm Accuracy: ±0.002 mm Weight: 0.1 kg Materials & special features Material: Special steel Version: Workshop execution Supply: Single item FAQ What tolerance does the pin offer? The gauge pin M323.F99 is specified with an accuracy of ±0.002 mm, suitable for fine inspection tasks. Which diameter should be expected for checks? The nominal diameter for this inspection pin is 15.99 mm, intended as a precise reference for end‑dimension verification. Is the pin suitable for fixture alignment? Yes; the 50 mm overall length and robust material make the pin appropriate for rapid fixture set‑up and positional referencing. What material is used for the pin? The pin is produced from special steel, selected for wear resistance and dimensional stability in workshop conditions. How is the item identified for ordering and stock? Order using SKU M323.F99; the GTIN 4061905069208 is provided for inventory and traceability Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
Fast, tactile checks where electronics are impractical
Gauges and test pins provide unequivocal go/no-go results for threads, bores, gaps and radii without relying on electronics. The range covers plug gauges and ring gauges for internal and external threads, feeler gauges and precision feeler strips for micro‑gap assessment, plus probe pins and measuring pins for tactile diameter and pitch checks.
How these tools work in the production environment
Mechanical gauges operate as direct reference standards: a plug gauge or ring gauge verifies conformity to thread profiles and mating ability, while limit gauges separate accept from reject in a single step. Test pins are used to tactilely measure small bore diameters, centre‑to‑centre distances and radii. Manufactured from hardened gauge steel or ceramic and often precision lapped, these instruments deliver immediate physical results that are ideal for incoming inspection, machine‑side checks and final control.
Measurable benefits that affect production performance
- Reduced scrap and rework through rapid, unambiguous pass/fail assessment.
- Increased repeatability thanks to very low measurement uncertainty and fine lapping.
- Lower downtime: quick checks at the machine save cycle time and reduce setup periods.
- Durable construction with high wear resistance from specialised, low‑distortion alloys.
- Versatile delivery formats: individual gauges, organised sets in wooden cases or metre‑length feeler rolls compliant with DIN 2269.
Why Metav is the practical choice for precision supplies
Metav combines decades of expertise with a broad warehouse and quality filtering from Emmerich. As a precision partner for industry, craft and trade, Metav supplies a comprehensive selection of gauges and test pins alongside complementary tools such as precision calipers and setting rings. With over 48,000 customers and a catalogue exceeding 250,000 items, Metav is positioned to supply reliably, reduce vendor complexity and support traceable quality control to national standards.
Summary
Gauges and test pins are indispensable for dependable, repeatable quality assurance where tactile, mechanical verification is preferred. Choose these plug gauges, ring gauges, feeler strips and probe pins when immediate, robust measurement decisions are required on the shop floor.
FAQ
What materials are gauges and test pins typically made from?
Gauges and test pins are usually manufactured from hardened gauge steel for durability and wear resistance; ceramic variants are available where thermal stability and minimal wear are critical.
How do thread gauges ensure mating capability?
Thread plug gauges and ring gauges check flank diameters and thread form against standards, providing a clear go/no‑go verdict that confirms pairability with mating parts.
Which tolerance class should I choose for probe pins and gauge sets?
Select tolerance classes aligned with your inspection requirements; for high‑precision tasks, sets produced to DIN 2269 or equivalent tolerance classes ensure micrometre‑level control and repeatability.
Can feeler gauges measure contact gaps in valve and engine work reliably?
Yes. Feeler gauges and precision feeler strips, supplied either as a fan or metre‑length rolls, allow accurate assessment of valve clearances and contact gaps down to micrometre increments.
How do limit gauges speed up in‑process inspection?
Limit gauges separate good from bad in a single, tactile operation, enabling rapid go/no‑go checks at the machine and reducing both inspection time and the likelihood of human interpretation errors.
Fragen zu diesen Produkten??
Mit mehr als 30 Jahren Erfahrung beraten wir Sie gerne persönlich.
Tel.: +49 2822 7131930
Mail: info@metav-werkzeuge.com