Precision gauge blocks and plug gauges for reliable dimensional control
Mechanical gauge blocks and plug gauges are essential for tactile verification of threads, bores and gap dimensions, providing fast, unambiguous go/no-go results that enhance process reliability and reduce scrap. Designed for industrial metalworking and toolmaking, these precision tools support incoming inspection and final quality checks by delivering traceable measurements in applications such as thread inspection, bore diameter testing and spacing checks. Manufactured from specially hardened, low-distortion alloys and fine-lapped for minimal measurement uncertainty, the range includes thread plug gauges, precision plug gauges and calibration gauge blocks to ensure long-term repeatability and wear resistance.
16.05mm Gauge Pin 50mm Length Workshop Grade, Special Steel - Metav IndustryLine
Take advantage of the combination of exact dimensional control, robust workshop construction and compact handling for reliable end‑measure checks. With a diameter of 16.05 mm, a length of 50 mm and a verified tolerance of ±0.002 mm, production faults are reduced and inspection throughput is increased. Order the gauge pin directly via Metav Werkzeuge or ask the consultants if further advice is required. Gauge pin, single — 16.05 mm diameter, 50 mm length (Metav IndustryLine) The Gauge pin, single, 16.05 mm, length 50 mm is a workshop‑grade precision pin designed for end‑dimension verification and go/no‑go checking in production and quality inspection. High‑accuracy tolerance ±0.002 mm Workshop version for robust handling Diameter precisely 16.05 mm Compact 50 mm length for tight fixtures Consistent, measurable accuracy for production control The pin delivers reproducible results thanks to its ±0.002 mm positional tolerance, which supports tight process control in serial inspection. A defined 16.05 mm diameter combined with a 50 mm shank reduces ambiguity at the measuring station, allowing rapid go/no‑go decisions and limiting rework. As a workshop precision tool, the pin is intended for repeatable end‑measurement tasks where precision and throughput are decisive. Technical terms: the quoted tolerance refers to the permissible deviation from nominal diameter under standard measurement conditions, which ensures compatibility with gauge fixtures and plug standards. Built for workshop conditions and secure handling Manufactured from special steel, this workshop execution offers mechanical resistance and stable surface finish for extended service life. The component’s modest mass (approx. 0.15 kg) and compact form factor make it simple to position in tight jigs and to handle with common inspection tools. Surface quality and material choice reduce wear from repeated insertion, so measurement drift is minimised and maintenance intervals are extended. For applications that demand practical robustness rather than laboratory fragility, this design prioritises uptime and operator confidence. Practical integration into inspection workflows The single gauge pin suits final dimension checks and can be used as a reference element in assembly fixtures or be part of quick inspection sets. Traceability is supported by clear identification (SKU M323.G05) which simplifies stock and inspection records. For processes that require rapid verification of shafts, bores or end faces, the pin is a compact and reliable option. Assistance and technical clarification are available from Metav Werkzeuge to align the component with existing gauges or measurement protocols, ensuring straightforward integration into quality routines. For dependable workshop inspection with the Metav IndustryLine gauge pin (SKU M323.G05) — contact Metav Werkzeuge to discuss suitability for specific end‑measure tasks or to place an order directly from Emmerich. Technical Data Article number: M323.G05 GTIN: 4061905069260 Manufacturer: Metav IndustryLine Dimensions & accuracy Diameter: 16.05 mm Length: 50 mm Tolerance: ±0.002 mm Weight: 0.15 kg Features & application Material: Special steel Workshop version Application: end‑dimension checks and go/no‑go verification Category: Gauge pin FAQ What materials is this gauge pin made from? The gauge pin is manufactured from special steel, providing a durable surface and stable geometry for workshop inspection tasks. Is the dimensional tolerance suitable for production control? Yes, the pin’s tolerance of ±0.002 mm makes it suitable for tight production checks and repeatable end‑measurement routines using the Metav IndustryLine gauge pin (M323.G05). Can this pin be used in go/no‑go fixtures and jigs? Yes, the compact 50 mm length and precise 16.05 mm diameter are suitable for incorporation into go/no‑go fixtures and for quick reference checks. How is the product identified for inventory and quality records? Identification is via SKU M323.G05 and GTIN 4061905069260, which support traceable stock management and inspection documentation. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
16.06 mm Gauge Pin Length 50 mm Workshop Finish - Metav IndustryLine
Taking advantage of its precise Ø 16.06 mm diameter, ±0.002 mm nominal tolerance and compact 50 mm length ensures reliable end‑measure checks in tight fixtures; order the test pin directly via Metav Werkzeuge or consult our specialists for application advice. Test pin Ø 16.06 mm, 50 mm length — Metav IndustryLine workshop version A single test pin Ø 16.06 mm, 50 mm length intended for accurate end‑measure and inspection tasks within fixtures and gauge assemblies. Workshop version for robust daily use Precision diameter Ø 16.06 mm Compact 50 mm length for tight fixturing Made from special steel High precision where small deviations matter The pin delivers a nominal tolerance of ±0.002 mm, a level of accuracy that makes it suitable for end‑measure comparisons and reference checks in quality control routines. Its defined diameter of Ø 16.06 mm provides a reproducible datum for plug gauges, alignment pins and short‑reach fixtures; the combination of tight tolerance and compact geometry reduces cumulative error when used as a reference in stacked or multi‑point measurement arrangements. This performance supports rational decision‑making in production by lowering reject rates and improving first‑pass yield. Robust workshop design that lasts Constructed from special steel and supplied as a single unit with a 50 mm shank, the component is designed for frequent handling and practical workshop environments. The workshop version specification emphasises resistance to mechanical wear during insertion and removal, while the moderate mass balances handling convenience with stability in the fixture. Such robustness minimises service interruptions and contributes to cost‑effective uptime across repetitive inspection tasks. Fits seamlessly into inspection and fixture workflows With its compact length, the pin integrates easily into gauge blocks, quick‑change fixtures and portable inspection rigs where space is limited. The small footprint and standard dimensioning enable straightforward replacement or interchangeability with existing Ø 16 mm nominal systems while maintaining traceable identification through the supplied SKU and GTIN. Using standardised reference pins like this one streamlines setup times and supports consistent measurement results across shifts and operators, reinforcing process reliability. For workshop‑grade gauge pins from Metav IndustryLine contact Metav Werkzeuge GmbH in Emmerich for specification guidance or to place an order through the Emmerich quality hub. Technical data Article number: M323.G06 GTIN: 4061905069901 Brand: Metav IndustryLine Facts Diameter: 16.06 mm Length: 50 mm Nominal tolerance: ±0.002 mm Weight: 0.15 kg Material: Special steel Special features Workshop version suitable for daily inspection use Intended use: end‑measure and fixture reference Supplied as a single test pin Traceable identification via GTIN and SKU FAQ What material is the pin made from? The test pin is manufactured from special steel, a material chosen to deliver durability and stable dimensional performance under repeated use. What accuracy can be expected from this test pin? The pin offers a nominal tolerance of ±0.002 mm, making it suitable for fine end‑measure checks and close‑tolerance inspection tasks. Which applications does this pin serve best? This single test pin is intended for end‑measure checks, fixture datum points and gauge assemblies where a compact, precise reference is required. Is the length and diameter compatible with standard fixtures? With a 50 mm length and Ø 16.06 mm diameter, the pin is designed to integrate into confined fixtures and standardised gauge setups that accept 16 mm nominal references. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
16.07mm Gauge Pin 50mm Length Workshop Version, Special Steel in Case - Metav IndustryLine
Combine precise 16.07 mm sizing with a tight ±0.002 mm tolerance and robust workshop construction to secure reproducible end‑measure checks; order the gauge pin directly via Metav Werkzeuge or consult our technical advisors for tailored specification support. Gauge pin, single, 16.07 mm — workshop-grade end-measure pin by Metav IndustryLine The Gauge pin, single, 16.07 mm, length 50 mm functions as a hardened end‑measure and reference plug for fixture set‑up, inspection benches and go/no‑go assessments in workshop environments Single gauge pin for end-measure checks Diameter 16.07 mm with ±0.002 mm tolerance Length 50 mm, workshop-grade construction Made from special steel for wear resistance Consistent accuracy for critical end‑measure tasks The M323.G07 is engineered for repeatable dimensional checks where accuracy matters. With a nominal diameter of 16.07 mm and a verified ±0.002 mm tolerance, the pin provides a stable reference for plug gauges, assembly fixtures and inspection routines. The tight tolerance reduces measurement scatter and shortens inspection cycles, supporting higher throughput in production control. Bold, measurable specifications make the M323.G07 suitable for precision checks on bores, seating surfaces and end stops. Durable design that withstands workshop use Constructed from special steel, the pin resists surface wear under frequent insertion and withdrawal, extending service intervals and lowering replacement frequency. The 50 mm length gives adequate engagement depth for reliable seating in most common fixture arrangements while remaining compact enough for handheld checks. The workshop-grade finish balances corrosion resistance with tactile clarity at the seating face, helping to preserve nominal dimensions through repetitive use and minimising downtime for maintenance. Practical integration with gauges and fixtures As a single, traceable reference element, this gauge pin integrates directly into measurement jigs, alignment tools and modular fixture systems. Marking and trace data (SKU M323.G07, GTIN 4061905069918) simplify inventory and process control. The pin’s geometry supports quick mounting in standard locating sleeves and can be used in sequence with control pins for comparative checks, allowing systematic validation of bore tolerances and end‑positioning without complex set‑ups. Productivity benefits and quality assurance Replacing ambiguous fit checks with a quantified reference reduces rework and inspection time. The M323.G07 helps to standardise pass/fail criteria across shifts, which supports repeatable assembly quality and faster throughput. Backed by Metav IndustryLine’s sourcing and quality filter in Emmerich, the pin contributes to a dependable supply chain for inspection consumables and ensures specifications are communicated clearly between purchaser and workshop. Contact Metav Werkzeuge for detailed specification advice on the Metav IndustryLine M323.G07 gauge pin and to arrange prompt delivery from Emmerich to the production floor (+49 2822 7131930, info@metav-werkzeuge.com) Technical data Article number: M323.G07 GTIN: 4061905069918 ECLASS: 21170231 Facts Nominal diameter: 16.07 mm Length: 50 mm Weight: 0.15 kg Tolerance: ±0.002 mm Special features Material: Special steel Workshop version Single gauge pin for end-measure tasks Category: Gauge pin (Messstifte) FAQ What nominal diameter does this gauge pin have? The gauge pin has a nominal diameter of 16.07 mm, specified with a tolerance of ±0.002 mm for the M323.G07. Which applications are suitable for this pin? The pin is intended for end‑measure checks, fixture referencing, plug‑gauge comparisons and seating checks in workshop and light production environments. What material is used for the pin? This gauge pin is made from special steel, selected for wear resistance and stable surface characteristics under frequent use. Can the pin be used in modular fixture systems? Yes, the geometry and 50 mm length are compatible with common locating sleeves and modular fixtures for repeatable positioning and inspection sequences. How is the product identified for ordering? Order using SKU M323.G07 or reference GTIN 4061905069918 to ensure the correct Metav IndustryLine gauge pin is supplied. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
16.08mm Test Pin, Single, 50mm Length, Workshop Version - Metav IndustryLine
Take advantage of the combination of high repeatability (±0.002 mm), a precise Ø 16.08 mm diameter and a robust 50 mm length to secure reliable end‑measure checks in the workshop; order the gauge pin directly via Metav Werkzeuge or consult our advisers for application support. Gauge pin M323.G08 — single gauge pin, Ø 16.08 mm, 50 mm length (Metav IndustryLine) The Gauge pin M323.G08 is a workshop‑grade precision pin for end‑measure checks, fixture alignment and reference gauging in machine shops and production workbenches. Workshop‑grade construction for daily use High‑precision tolerance ±0.002 mm Solid 50 mm length for stable seating Special steel for wear resistance Precision where fit and repeatability matter A tolerance of ±0.002 mm positions this gauge pin among precision‑oriented reference tools. The nominal diameter 16.08 mm provides a defined contact geometry for end‑measurements and plug‑type references; the tight tolerance reduces variation between repeated checks, which translates into fewer machine adjustments and less scrap. Explaining the figure: a deviation of two micrometres is smaller than a human hair, so the pin is suitable where close fits and tight assembly clearances are specified. Durable design tuned to workshop conditions The pin is manufactured from special steel, optimised for service in a workshop environment where repeated insertion, seating and handling occur. The solid 50 mm length gives sufficient engagement for stable seating while remaining easy to handle; a mass of approximately 0.15 kg contributes to a reassuring feel without unnecessary bulk. The workshop variant is finished for practical use, making the component resistant to everyday wear and simplifying integration into fixture sets or inspection routines. Practical use and operational benefits As a single gauge pin in the range of gauge pins, this item is intended for end‑measure and reference applications, especially where a compact, repeatable datum is required. The compact dimensions keep handling straightforward during batch inspection or when pins are exchanged in jigs and fixtures. The clear technical specification and robust material choice support predictable measurement workflows, reducing downtime and ensuring that results from manual checks are consistent and traceable within standard quality processes. Contact Metav Werkzeuge for precise application advice or to secure the Metav IndustryLine gauge pin M323.G08 for workshop use; our team in Emmerich is available to assist with product selection and integration into existing inspection routines. Technical Data SKU: M323.G08 GTIN: 4061905070204 Product: Gauge pin, single Facts Diameter: 16.08 mm Length: 50 mm Tolerance / repeatability: ±0.002 mm Weight: 0.15 kg Special features Material: Special steel Version: Workshop execution Category: Gauge pins Application focus: End‑measure and reference gauging FAQ What tolerance does the gauge pin offer? The gauge pin offers a tolerance of ±0.002 mm, providing high repeatability for reference measurements. Is the pin suitable for fixture alignment and end‑measure checks? Yes, the M323.G08 gauge pin is designed for end‑measure checks and fixture alignment in workshop and production environments. What material is the pin made from? The pin is made from special steel, chosen for wear resistance and suitability for daily workshop use. How does the pin's length affect its use? The 50 mm solid length provides stable seating and easy handling, making it well suited to insertion into jigs and reference housings. Which product identifier should be quoted when ordering? Please quote the SKU M323.G08 or the GTIN 4061905070204 when ordering or enquiring about this gauge pin. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
16.09mm Test Pin 50mm Workshop Version, Special Steel - Metav IndustryLine
Take advantage of the combination of high reproducibility, robust workshop design and sub‑millimetre accuracy to make end‑measurement checks reliable and repeatable; order the gauge pin directly via Metav Werkzeuge or contact our consultants for application advice. Gauge pin, single, 16.09 mm diameter — 50 mm length, Metav IndustryLine A gauge pin for precise end‑measurement and go/no‑go checks in workshop and quality‑control environments, designed as a compact, robust reference for assembly and inspection tasks Workshop version for robust use Diameter 16.09 mm for precise fit Length 50 mm for standard handling High accuracy ±0.002 mm Guaranteed measurement repeatability for final checks The gauge pin delivers a diameter of 16.09 mm with a stated accuracy of ±0.002 mm, enabling reliable acceptance testing and dimensional confirmation at the end of the manufacturing process. Such tight tolerances reduce the risk of part rejection and rework by providing a clear, measurable reference for go/no‑go decisions. Constructed from special steel, the component maintains form under repeated contact, supporting consistent results across inspection cycles. The emphasis here is on measurable performance: stable dimensions translate directly into fewer production interruptions and lower overall inspection uncertainty. Compact, workshop‑grade handling for efficient inspections With a length of 50 mm and a compact profile the pin is configured as a micro‑class inspection tool (measurement range within the 10–100 mm band), offering the best compromise between reach and stiffness for small to medium‑sized components. The workshop version is optimised for regular use in machine shops and inspection benches, where quick placement and tactile feedback speed up throughput. The balanced design aids repeatable seating in fixtures and jigs, so cycle times are reduced without sacrificing measurement confidence. Handling benefits include straightforward positioning and minimal set‑up time for routine checks. Purposeful design for production control and traceability Designed as a single inspection pin, the component supports targeted end‑dimension verification across batches and assemblies. The compact reference aids fast decisions in serial inspection and sample testing, feeding directly into quality documentation and process control. The item is identified by SKU M323.G09 and GTIN 4061905070211 for straightforward procurement and stock management, helping integrate the item into existing calibration and traceability systems. For workshops seeking a robust, precise reference for final dimension checks, this pin offers a pragmatic balance of precision, durability, and straightforward integration. Contact Metav Werkzeuge for application guidance or to discuss stock and delivery options for the Metav IndustryLine gauge pin — email info@metav-werkzeuge.com or call +49 2822 7131930 Technical Data SKU: M323.G09 GTIN: 4061905070211 Manufacturer: Metav IndustryLine Facts Diameter: 16.09 mm Length: 50 mm Accuracy: ±0.002 mm Weight: 0.15 kg Special features Material: special steel Version: workshop execution Category: gauge pins ECLASS: 21170231 FAQ What inspection tasks is this gauge pin best suited for? The gauge pin is intended for end‑measurement and go/no‑go checks on small to medium components; the Metav IndustryLine pin (SKU M323.G09) is optimised for workshop and quality‑control benches. Is the diameter tolerance suitable for serial inspection? Yes, the stated tolerance of ±0.002 mm makes the pin appropriate for serial inspection where tight dimensional control is required. Which material is the pin made from and why does it matter? The pin is manufactured from special steel, chosen for dimensional stability and wear resistance to preserve the reference diameter under repeated use. How can the pin be ordered or integrated into stock systems? The item is listed under SKU M323.G09 with GTIN 4061905070211 to support procurement and inventory processes; contact Metav Werkzeuge for order handling and delivery information. Metav IndustryLine: Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
16.11mm Gauge Pin, Workshop Version, 50mm Length - Metav IndustryLine
Taking advantage of ±0.002 mm accuracy, a 16.11 mm diameter and a robust special steel body ensures reproducible fits and fewer inspection reworks; the single-pin format and compact 50 mm length simplify handling in busy workshops. Order the gauge pin directly via Metav Werkzeuge or consult our experts for specification matching. Gauge pin M323.G11 — 16.11 mm diameter, 50 mm length (Metav IndustryLine) Gauge pin M323.G11 as a single precision test pin for end‑measurement and assembly checks in workshop metrology Diameter accuracy ±0.002 mm 16.11 mm diameter, 50 mm length Special steel construction Delivered in a transport box Consistent go/no‑go results through defined tolerance control The core benefit of this test pin is repeatable dimensional control: manufactured to a tolerance of ±0.002 mm, the pin reduces uncertainty during fit checks and final inspection. For production lines and quality departments that require narrow clearance verification, this level of tolerance supports fast decision‑making and lowers the risk of scrap or rework. The precise shaft size of 16.11 mm is suited to nominal fits where minimal deviation is acceptable, enabling reliable pass/fail assessment with simple plug tests. Durable construction for repeated workshop use Built as a workshop version, the pin combines a compact 50 mm overall length with a robust special steel alloy to withstand frequent handling and contact with mating parts. The chosen grade provides strength and wear resistance while keeping the pin light and easy to position; the item weight of 0.15 kg aids steady manual use without excessive inertia. Delivered in a transport box, the pin arrives protected against transit damage and ready for immediate integration into inspection kits or fixture sets. Streamlined inspection and traceability in production workflows The single‑pin format speeds up routine checks and reduces setup time compared with multi‑pin sets, which is an advantage in high‑throughput or mixed‑batch environments. Marked and traceable as M323.G11 and listed under GTIN: 4061905070235, the component can be keyed into inventory and quality systems for simple reference, auditability and replacement planning. Integration into existing metrology processes is straightforward: the pin functions as a reference for end‑dimension checks, assembly verification and calibration routines where a compact, precise gauge is required. Contact Metav Werkzeuge today to specify the M323.G11 for workshop inspection kits or to discuss batch requirements and delivery options; Metav Werkzeuge offers expert guidance from Emmerich and a broad metrology portfolio to match production needs Technical Data Article number: M323.G11 GTIN: 4061905070235 Category: Gauge pins (Messstifte) Material: Special steel Label: Gauge pin, single, 16.11 mm diameter, 50 mm length Facts Diameter: 16.11 mm Length: 50 mm Tolerance: ±0.002 mm Weight: 0.15 kg Special features Workshop version Delivered in a transport box Single, precision‑finished pin Suitable for end measurement and assembly checks FAQ What material is the gauge pin made from? The gauge pin M323.G11 is manufactured from a specially selected special steel to provide durability and wear resistance for workshop use. What tolerance and precision level does the pin offer? The M323.G11 is produced to a tolerance of ±0.002 mm, enabling tight fit checks and consistent inspection outcomes. Which applications suit this test pin best? The single gauge pin is intended for end‑dimension verification, assembly checks and quick go/no‑go testing in mechanical workshops and small series production. Is the pin supplied ready for use and protected in transit? The M323.G11 is supplied as a single precision pin and delivered in a transport box for secure transit and immediate use upon arrival. How should the pin be recorded in inventory and quality systems? Use the article number M323.G11 and GTIN: 4061905070235 for traceability, procurement and audit records to ensure consistent replacement and calibration planning. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
16.12 mm Gauge Pin, Single, 50 mm Length, Workshop Version - Metav IndustryLine
Take advantage of the Ø16.12 mm diameter and the workshop‑grade construction to ensure repeatable fit checks with a tight tolerance of ±0.002 mm; the compact 50 mm length and included transport case support reliable handling and secure storage. Order directly via Metav Werkzeuge or consult our specialists for application advice. Gauge pin, single – Ø16.12 mm, 50 mm length (Metav IndustryLine) The gauge pin, single, 16.12 mm is a compact test pin for end‑measurements and fit verification in precision workshops and production inspection. Workshop version for robust use Tolerance ±0.002 mm for precise fits Special steel for long service life Delivered in transport case for safe handling Precision that reduces rework and speeds inspection The compact test pin delivers a measurable improvement in repeatability thanks to its tolerance of ±0.002 mm, which helps to reduce rework and avoid false rejects during assembly or incoming inspection. Designed for short‑span checks, the Ø16.12 mm diameter and 50 mm length make the component easy to position in jigs and bores while maintaining the dimensional integrity required for fit assessment. This reliability is particularly valuable in high‑mix workshops where fast, trustworthy checks shorten cycle times and support consistent quality control. Durable construction for frequent workshop use Made from special steel, the component is engineered for repeated contact and handling typical of workshop environments; the workshop version emphasises mechanical robustness and practical longevity. The modest weight and compact form factor allow straightforward manual handling during measurement routines, and the included transport case protects the pin in transit and storage. Together, these attributes translate into reduced downtime for replacement and a dependable measuring accessory for everyday inspection tasks. Clear suitability and straightforward handling in measurement workflows Classified in the micro range for small‑scale gauge items, the pin is ideal where short reach and high accuracy converge: end‑measurements, plug gauges and fit checks on shafts, bores and mating parts. The straightforward geometry simplifies use with optical comparators, pin gauges and manual benches, while the compact dimensions contribute to comfortable, repeatable handling. For bespoke inspection setups or if integration into a gauge stack is planned, Metav Werkzeuge’s technical advisers can provide guidance on compatibility and best practice. Contact Metav Werkzeuge for tailored application advice on the Metav IndustryLine gauge pin and ensure the right measuring strategy for your workshop environment Technical Data Article number: M323.G12 GTIN: 4061905070242 Weight: 0.15 kg Material: Special steel Diameter: 16.12 mm Length: 50 mm Tolerance: ±0.002 mm Version: Workshop execution Delivery: Transport case included Facts Diameter: 16.12 mm Length: 50 mm Weight: 0.15 kg Tolerance: ±0.002 mm Special features Workshop execution Special steel material Transport case for safe handling Suitable for end‑measurements and fit checks FAQ What is the dimensional tolerance of this gauge pin? The gauge pin is specified with a tolerance of ±0.002 mm, making the Metav IndustryLine test pin suitable for precise fit and end‑measurement tasks. Which material is used for the pin? This test pin is manufactured from special steel, selected for robustness in workshop use and repeated inspection cycles. Is the pin supplied with protection for transport? Yes, the item is delivered in a transport case, ensuring safe handling and protection during storage and transport. What are the exact dimensions and the SKU for ordering? The pin has a diameter of 16.12 mm, a length of 50 mm, and is listed under SKU M323.G12. Is this pin suitable for plug gauge and fit checks in small bores? Its compact shape and micro‑range dimensions make it well suited for plug‑type checks and fit verification on small bores and mating parts using standard inspection setups. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
16.13mm Gauge Pin 50mm Length Workshop Version Plastic Case - Metav IndustryLine
Benefit from workshop‑grade robustness combined with precise diameter control: the gauge pin delivers a 16.13 mm nominal diameter with a tight ±0.002 mm tolerance and a 50 mm length for stable handling. Order the gauge pin directly via Metav Werkzeuge or consult our specialists for application advice. Gauge pin M323.G13 — 16.13 mm diameter, 50 mm length (Metav IndustryLine) The gauge pin M323.G13 is a precision test pin designed for reliable end‑measurements and inspection tasks in metrology and workshop environments. Workshop version, robust design Diameter 16.13 mm with ±0.002 tolerance 50 mm length for stable handling Made from special steel for wear resistance Precision where end measurements matter The M323.G13 is engineered for consistent accuracy in end‑measurement applications. With a nominal 16.13 mm diameter and a verified ±0.002 mm tolerance, the test pin supports repeatable results when checking bores, fits or reference points. The compact 50 mm length keeps the probe stiff during contact, reducing bending errors and making the item particularly suitable for routine inspection tasks where measurement stability is essential. This combination of tight tolerances and a short, rigid form factor reduces uncertainty and shortens setup time on the shop floor. Built for workshop use and repeatability Supplied in a workshop version, the pin balances durability with straightforward handling. The special steel construction provides enhanced wear resistance, extending service life under frequent use. The modest mass and defined length allow quick positioning in fixtures and gauges, supporting a smooth workflow in measurement benches and go/no‑go checks. The robust design helps maintain dimensional integrity over multiple cycles, meaning fewer replacements and more predictable inspection intervals. Applications optimised for inspection efficiency This precision test pin is intended primarily for end measurements such as bore checks, alignment referencing and plug‑gauging tasks in maintenance, production inspection and small series quality control. The 50 mm stem length offers reliable grip in chucks or fixture seats while the close diameter tolerance makes the pin suitable as a master gauge or reference artefact. For users requiring systematic verification, the pin works well as part of a set of master plugs or as a dedicated reference in routine measurement procedures. Quality attributes and workshop integration Traceable manufacturing and clear article identification support quality management practices in industrial settings. The gauge pin’s compact geometry simplifies handling and storage in modular test sets, while its material choice limits surface degradation under normal contact conditions. For procurement and inventory, the distinct SKU and GTIN ensure easy traceability within purchasing and calibration records, helping to maintain conformity across workshops and inspection labs. For workshop reliability and precise end‑measurement capability, contact Metav Werkzeuge to discuss the M323.G13 gauge pin and arrange supply tailored to production needs. Technical data SKU: M323.G13 GTIN: 4061905070259 Material: Special steel Weight: 0.15 kg Length: 50 mm Facts Nominal diameter: 16.13 mm Tolerance: ±0.002 mm Measurable range: 16.13 mm Length: 50 mm Weight: 0.15 kg Special features Workshop execution Category: Gauge pins / test pins Single item supply Robust, wear‑resistant material Application focus: end measurements / inspection FAQ What tolerance does the gauge pin offer? The M323.G13 gauge pin is manufactured to a tolerance of ±0.002 mm, suitable for fine inspection and reference tasks. What material is the pin made from and how does it perform? The pin is made from special steel, chosen for its wear resistance and dimensional stability in workshop environments. Is the item supplied individually and how is it identified? The gauge pin is supplied as a single test pin and is listed under SKU M323.G13 (GTIN 4061905070259) for clear traceability. For which measurement tasks is this pin recommended? This test pin is optimised for end measurements, bore checks and general inspection work where a rigid, precisely sized reference is required. Can the pin be used as a master gauge in a set? Yes; the dimensional stability and tight tolerance make the M323.G13 suitable as a master reference within inspection sets or fixture calibrations. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
16.16 mm Gauge Pin Length 50 mm Workshop Version, Special Steel - Metav IndustryLine
The robust gauge pin combines workshop-grade construction with a tight ±0.002 mm tolerance and a stable 50 mm length, giving reliable end‑measure references for repetitive checks and assembly tasks. Order the M323.G16 directly via Metav Werkzeuge or consult the Metav team for application advice. Gauge Pin M323.G16 – Ø 16.16 mm, 50 mm Length (Metav IndustryLine) The Gauge Pin M323.G16 is a single workshop‑grade reference pin designed for precise end‑measure checks and alignment tasks in industrial metrology. Workshop version, robust design Diameter 16.16 mm nominal reference Tolerance ±0.002 mm for high repeatability 50 mm length for secure handling Precision that supports reliable pass/fail decisions The M323.G16 gauge pin serves as a stable dimensional reference where repeatability matters. With a stated tolerance of ±0.002 mm, the pin is suitable for fine verification tasks and helps reduce measurement scatter when used as an end‑stop or reference mandrel. The close tolerance minimises ambiguity in go/no‑go checks and streamlines incoming inspection procedures, turning a simple pin into a dependable datum for routine quality controls. Design and handling optimised for workshop use Constructed from special steel and finished as a workshop version, the pin’s 50 mm length provides a convenient grip and reduces the risk of slippage during placement. The 16.16 mm diameter is presented as a nominal reference dimension so it mates consistently with matching bores or gauge blocks. Supplied as a single pin and presented in a protective case, the unit is straightforward to store and transport within a busy shop environment while preserving surface integrity. Practical benefits for production and assembly processes Using a hardened, dimensionally stable reference element simplifies fit checks, alignment tasks and end‑measure controls on assemblies. The compact form factor and modest weight (0.15 kg) mean the pin can be used comfortably at a workbench or fitted in test fixtures without significant overhang or imbalance. The workshop configuration prioritises durability and ease of use, turning a basic reference into a time‑saving tool in repetitive production sequences. Traceability and identification for workshop logistics Each unit carries identification data to aid inventory and process documentation: SKU M323.G16 and GTIN 4061905068126 are available for procurement and stock control. The clear labelling and single‑piece supply simplify replacement and prevent confusion on multi‑pin benches. For procurement teams and workshop managers, this single‑pin solution offers an uncomplicated specification to include in inspection kits and maintenance trolleys. For precise end‑measure references, choose the Metav IndustryLine gauge pin M323.G16 via Metav Werkzeuge and discuss any specific application requirements with the Metav specialists in Emmerich Technical data Article number: M323.G16 GTIN: 4061905068126 SKU: M323.G16 Facts Diameter: 16.16 mm Length: 50 mm Tolerance: ±0.002 mm Weight: 0.15 kg Special features Material: special steel Workshop version Supplied single in a protective case Category: Gauge pin / reference pin FAQ What is the primary use of this gauge pin? The M323.G16 gauge pin is intended as a reference for end‑measure checks, alignment tasks and simple go/no‑go verifications in workshop and production settings. What tolerance can be expected from the pin? The gauge pin is specified with a tolerance of ±0.002 mm, providing a tight reference for repeatable dimensional checks. What material is the pin made from? The pin is manufactured from special steel, giving a balance of hardness and wear resistance appropriate for routine metrology use. How is the pin supplied for storage and transport? The unit is supplied as a single pin and delivered in a protective case to preserve the reference surface during storage and handling. How can the pin be identified in stock or ordering systems? Identification is possible via SKU M323.G16 and GTIN 4061905068126, which are suitable for procurement and inventory control. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
16.17mm Test Pin Length 50mm Workshop Version, Special Steel - Metav IndustryLine
Take advantage of the combination of workshop-grade robustness, tight ±0.002 mm tolerance and a compact 16.17 mm diameter for reliable end‑size checks; order the gauge pin directly via Metav Werkzeuge or consult our advisors for application guidance. Gauge pin M323.G17 — single gauge pin, 16.17 mm diameter, 50 mm length (Metav IndustryLine) Gauge pin M323.G17 is a single precision pin gauge designed for fast go/no‑go and reference checks in workshop environments, featuring a 50 mm overall length and a nominal diameter of 16.17 mm. Workshop version for everyday use Nominal diameter 16.17 mm with ±0.002 mm tolerance 50 mm overall length for easy handling Made from special steel for wear resistance Keep production within tolerance with repeatable checks The single‑piece pin is manufactured to a tight ±0.002 mm geometric tolerance, making it suitable for final dimension checks and clearance verification where repeatability is critical. The compact geometry and defined shaft help to reduce positioning error during insertion, while the nominal 16.17 mm diameter provides a clear go/no‑go decision without interpretation. For inspection routines that prioritise speed and unambiguous results, this tool shortens cycle times and supports consistent quality control. Designed for robust workshop handling and secure transport Built as a workshop version, the pin combines a wear‑resistant special steel construction with a balanced 50 mm length that eases manual handling and stabilises insertion. The moderate mass (approx. 0.15 kg) gives a reassuring feel without unnecessary bulk, and the component is delivered in a protective transport case to prevent damage during storage and transfer. This practical packaging helps maintain the pin’s calibrated condition and reduces downtime from accidental marks or corrosion. Traceable identification and straightforward application in inspection workflows Marked with SKU M323.G17 and GTIN 4061905069062, the gauge pin integrates cleanly into stock and inspection records for traceability. Its single‑diameter format is ideal for end‑size verification and quick acceptance testing of bores, dowel seats and mating parts; the simple geometry minimises measurement uncertainty and is compatible with manual gauges, fixture checks and tactile inspection benches. Using clearly identified, workshop‑grade reference pins supports a rational inspection strategy and reduces the risk of ambiguous results during routine sampling. Contact Metav Werkzeuge to discuss suitability for specific parts, traceability needs or batch procurement — Metav’s specialists in Emmerich will advise on integration and delivery options Technical data Article number: M323.G17 GTIN: 4061905069062 Weight: 0.15 kg Length: 50 mm Diameter: 16.17 mm Tolerance: ±0.002 mm Facts Nominal diameter: 16.17 mm Overall length: 50 mm Mass: 0.15 kg SKU: M323.G17 GTIN: 4061905069062 Special features Workshop version construction Material: special steel Delivered in a plastic or wooden transport case Category: Gauge pins Story trigger: end sizes FAQ What accuracy does the gauge pin offer? The gauge pin M323.G17 is manufactured to a ±0.002 mm tolerance, suitable for repeatable workshop checks and quick go/no‑go assessments. Can the pin be used for bore acceptance tests? Yes, the single‑diameter pin is intended for final size verification of bores, dowel seats and mating features where a defined nominal diameter check is required. What material is the pin made from and how durable is it? The pin is made from special steel, chosen for wear resistance in frequent inspection cycles; the workshop version balances durability and handling. How is the item delivered to protect its condition? The gauge pin M323.G17 is supplied in a protective transport case to prevent handling damage and to preserve dimensional integrity between uses. How is the product identified for inventory and traceability? Identification is provided via SKU M323.G17 and GTIN 4061905069062 for straightforward recording in inspection and stock systems. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
16.18mm Test Pin 50mm Length Workshop Version - Metav IndustryLine
Take advantage of the combination of workshop‑grade robustness, ±0.002 mm accuracy and a compact 50 mm length for reliable end‑dimension checks; order the gauge pin directly via Metav Werkzeuge or consult our technical advisors if clarification is required. Gauge pin, single, 16.18 mm, length 50 mm — Metav IndustryLine workshop version A Gauge pin, single, 16.18 mm, length 50 mm designed for precise end‑size verification and fixture alignment in workshop metrology Workshop version for robust use Diameter 16.18 mm, length 50 mm Accuracy ±0.002 mm Special steel construction Ensure repeatable end‑size verification with micrometric accuracy This single gauge pin is specified for end‑dimension controls where repeatability matters. With a nominal diameter of 16.18 mm and a stated accuracy of ±0.002 mm, the pin serves as a fixed reference for go/no‑go checks, alignment in jigs and verification of bore diameters. The tolerance figure indicates that deviations remain within two thousandths of a millimetre, which supports consistent pass/fail decisions on production lines and in quality inspections. The compact 50 mm length keeps handling straightforward while offering sufficient engagement for most workshop fixturing tasks. Designed for workshop conditions and long service life Constructed from special steel, the pin is finished to withstand frequent handling and contact with mating parts. The workshop specification reflects a balance between wear resistance and machinability, ensuring that the reference surface maintains form over repeated cycles. At approximately 0.15 kg, the component combines manageable mass with the stiffness needed to avoid bending during placement. For users who require robust, repeatable references in assembly or inspection fixtures, this design reduces the need for frequent replacement and supports continuous production throughput. Practical integration into inspection and fixturing workflows The pin is intended as a straightforward, verifiable datum in fixtures, test benches and assembly aids. Its nominal size and close tolerance make it suitable for verifying final dimensions and for use as a locating element in modular jigs. Traceability is supported by the SKU and GTIN, allowing the component to be recorded within inventory and quality systems; this simplifies batch control and replacement planning. For processes that demand clear, measurable criteria, the pin supplies a fixed benchmark that translates directly into fewer ambiguous measurements and faster decision cycles. For purchase enquiries or to discuss suitability for a specific inspection task, contact Metav Werkzeuge for tailored advice and reliable supply from Emmerich. Technical data Article number: M323.G18 GTIN: 4061905069079 SKU: M323.G18 Manufacturer: Metav IndustryLine Material: Special steel Facts Diameter: 16.18 mm Length: 50 mm Weight: 0.15 kg Accuracy: ±0.002 mm Special features Workshop version Single gauge pin Intended for end‑size verification FAQ What tolerance does this gauge pin offer? The gauge pin is specified with an accuracy of ±0.002 mm, providing micrometric repeatability appropriate for end‑size checks with the Metav IndustryLine single gauge pin (SKU M323.G18). Which material is used and what does it mean in practice? The pin is made from special steel, offering durability and stable contact surfaces; this makes the component suitable for repetitive use in workshop fixturing and inspection tasks. Can this pin be used for alignment in jigs and fixtures? Yes. The 16.18 mm nominal diameter and close tolerance make the pin suitable as a locating datum for jigs, test benches and assembly aids where fixed references are required. Is a calibration certificate included with the product? Product data does not state a calibration certificate as standard for this item; calibration options can be arranged separately if traceable measurement certification is required. What typical applications suit this gauge pin? Common uses include end‑dimension verification, bore checking, fixture locating and repeatable go/no‑go controls in workshop metrology using the Metav IndustryLine single gauge pin M323.G18. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
16.19mm Gauge Pin, Single, 50mm Length, Workshop Version - Metav IndustryLine
Take advantage of the combination of exact dimensional control, compact handling and workshop‑ready construction for reliable end‑dimension checks; order the part via Metav Werkzeuge or consult our specialists for application guidance. Gauge Pin M323.G19 — 16.19 mm diameter, 50 mm length (Metav IndustryLine) The Gauge Pin M323.G19 is a precision reference pin designed for go/no‑go and end‑dimension testing in production and quality control environments. Workshop version for robust daily use Diameter 16.19 mm with ±0.002 mm tolerance Length 50 mm, compact and stable Supplied in protective transport case Consistent dimensional control for routine inspections The M323.G19 is built to deliver repeatable results in high‑throughput inspection workflows. With a nominal diameter of 16.19 mm and a manufacturing tolerance of ±0.002 mm, this reference pin supports tight acceptance criteria and reduces uncertainty during pass/fail checks. Classified in the micro range (max. measuring span 10–100 mm), the pin is intended where compact geometry and minimal deformation are required, making it suitable for fine mechanical assemblies and short‑reach gauging tasks. The measured accuracy provides a clear rational benefit: fewer false rejects and faster, more reliable process control. Built for daily workshop use and straightforward handling Constructed from special steel and delivered as a workshop version, the gauge pin withstands the rigours of routine use while remaining easy to handle. Its 50 mm length gives a compact, low‑moment profile that reduces bending and aids one‑hand operation for quick checks at the bench. The relatively low mass contributes to comfortable handling during repetitive measurements. For transport and protection between uses the item is supplied in a protective transport case, which preserves surface condition and dimensional integrity over time — a practical advantage in busy production environments. Practical integration into quality procedures This reference pin is suitable for rapid go/no‑go testing, end‑dimension verification and use as a setting standard in fixture checks. Supplied with clearly traceable identification (SKU and GTIN), the component can be recorded easily within inspection logs and ERP systems, supporting traceability and audit requirements. The robust specification and clear numeric data make the pin a rational choice where repeatability and traceability matter most, helping to reduce rework and maintain production throughput while simplifying inspection routines. For reliable, workshop‑grade precision and stock availability from the Emmerich quality hub, contact Metav Werkzeuge for application advice and to request the M323.G19 gauge pin supplied from our warehouse Technical Data Article number: M323.G19 GTIN: 4061905069086 Facts Diameter: 16.19 mm Length: 50 mm Weight: 0.15 kg Nominal tolerance: ±0.002 mm Special features Material: Special steel Version: Workshop execution Delivery: Supplied in protective transport case FAQ What tolerance does the gauge pin offer for dimensional checks? The gauge pin is manufactured to a nominal tolerance of ±0.002 mm, enabling precise end‑dimension verification with high repeatability. Is the pin suitable for fine mechanical or watchmaking tasks? Yes, with a diameter of 16.19 mm and classification in the micro measuring range, the pin is suitable for compact, high‑precision components and fine mechanical applications. How is the gauge pin protected during transport and storage? The part is supplied in a protective transport case to preserve the surface and maintain dimensional integrity between uses. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
16.1mm Gauge Pin 50mm Length Workshop Version - Metav IndustryLine
Benefit from a compact, workshop-quality reference that pairs 16.1 mm nominal diameter with a ±0.002 mm tolerance and a robust special steel construction—ideal for repeatable end‑measure checks. Order the reference pin directly via Metav Werkzeuge or consult our specialists for application advice. Gauge Pin, single Ø 16.1 mm, 50 mm length (M323.G10) — Metav IndustryLine The Gauge Pin, single Ø 16.1 mm, 50 mm length provides a precise, hardwearing reference element for workshop metrology tasks such as end‑measure checks, fixture verification and go/no‑go set‑ups. Workshop-grade construction, robust finish Diameter 16.10 mm with ±0.002 mm accuracy 50 mm body for stable reference Special steel for repeatable checks Consistent reference for production control A compact reference element with a stated ±0.002 mm tolerance guarantees repeatable comparisons during short‑range inspections. The small diameter of 16.1 mm and the solid construction make the pin suitable as a fixed datum when checking end measures or verifying bore gauges; the specification corresponds to micrometre‑level repeatability (2 µm), which supports tight tolerance monitoring without complex instrumentation. This clarity in performance reduces uncertainty in routine checks and streamlines pass/fail decisions on the shop floor. Built for workshop handling and longevity The 50 mm length delivers a stable contact surface while remaining easy to handle and position in fixture setups; its compact form minimises leverage and the risk of bending during use. Constructed from special steel, the pin resists routine wear and preserves the measuring diameter over many cycles, so the component remains a reliable reference in maintenance and assembly environments. The workshop-grade finish ensures predictable surface interaction with measuring tools and reduces the need for frequent replacement, supporting continuous operation. Practical integration into inspection workflows The item listed as M323.G10 is a single, precision gauge pin designed for straightforward integration: it serves as a reference for end‑measure checks, for verifying locating elements and for use as a calibration artefact within a set of gauge pins. Its compact dimensions make it easy to store alongside fixture tooling and to insert into jigs and test blocks. Where traceable certification is required, specific calibration services can be arranged separately to match internal quality management needs; otherwise the pin functions as a dependable workshop reference for daily quality control. Contact Metav Werkzeuge today to discuss how the Metav IndustryLine M323.G10 gauge pin can be specified for your inspection routine or to request compatibility advice for existing fixtures. Technical data Article number: M323.G10 GTIN: 4061905070228 Manufacturer: Metav IndustryLine Label: Prüfstift, einzeln, 16,1 mm Länge 50 mm Facts Diameter: 16.1 mm Length: 50 mm Tolerance / deviation: ±0.002 mm Weight: 0.15 kg Special features Material: special steel Product type: single gauge pin Application focus: end measures / final dimension checks Category: gauge pins FAQ Is an ISO 17025 calibration certificate included? No ISO 17025 certificate is stated for this item; the gauge pin is provided as a workshop reference with the specified tolerance. What is the pin made from? The M323.G10 is manufactured from special steel, chosen for wear resistance and dimensional stability under normal workshop use. For which tasks is this pin suited? Typical uses include end‑measure checks, fixture verification and acting as a fixed datum in go/no‑go setups or comparative inspections. How significant is the ±0.002 mm tolerance in practice? A tolerance of ±0.002 mm corresponds to a repeatability on the order of 2 micrometres, enabling reliable detection of small deviations in short‑range measurements. Can this pin be used with existing gauge blocks and pins? Yes; the single gauge pin format and its nominal diameter are compatible with common pin blocks and locating fixtures used in workshop metrology. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
16.21mm Gauge Pin, Single, 50mm Length, Workshop Version - Metav IndustryLine
Precision 16.21 mm gauge pin in workshop execution, made from special steel with a ±0.002 mm tolerance and a 50 mm usable length for reliable end‑measure checks; supplied in a protective case. Order the gauge pin directly via Metav Werkzeuge or ask our consultants if needed. M323.G21 gauge pin — 16.21 mm, 50 mm length (Metav IndustryLine) A M323.G21 gauge pin engineered for repeatable end‑measure verification and compact inspection tasks in workshop environments. Workshop execution, robust construction Diameter precisely 16.21 mm ±0.002 mm 50 mm length for confined and repeatable checks Supplied in a protective case for transport and storage Repeatable accuracy for end‑measure verification The compact cylindrical design delivers consistent dimensional control for end‑of‑line checks and plug‑gauge routines. With a nominal diameter of 16.21 mm and a declared tolerance of ±0.002 mm, the pin reduces measurement uncertainty and helps avoid rework downstream. The small form factor is particularly suitable where tight positional repeatability is required; the precision of the component supports quick go/no‑go assessments and high throughput in inspection sequences. Workshop robustness that maintains precision Manufactured from special steel and specified as a workshop execution, the pin withstands regular handling while retaining surface finish and dimensional stability. The chosen material balances wear resistance with machinability to ensure long service life under routine use. Delivered in a protective case, the pin is protected during transport and storage, which preserves the calibration state and minimises downtime that would otherwise arise from accidental damage. Practical use and benefits for production routines The gauge pin simplifies end‑measurement tasks in tight assemblies and fixtures: its 50 mm length gives enough engagement for reliable centreline checks without obstructing neighbouring features. The simple geometry requires minimal fixturing and supports fast, repeatable measurement cycles—benefits that translate into measurable time savings on inspection tasks. Supplied labelling and the clear SKU facilitate traceability in inventory management and quality records. Contact Metav Werkzeuge for fast delivery and expert advice on Metav IndustryLine gauge pins; telephone +49 2822 7131930 or e‑mail info@metav-werkzeuge.com Technical data Article number: M323.G21 GTIN: 4061905069109 EClass: 21170231 Facts Diameter: 16.21 mm Length: 50 mm Tolerance: ±0.002 mm Weight: 0.15 kg Special features Material: special steel Version: workshop execution Delivery: protective case included Category: measuring pins (Messstifte) FAQ What tolerance does the M323.G21 gauge pin offer? The M323.G21 gauge pin from Metav IndustryLine is specified with a tolerance of ±0.002 mm, suitable for fine inspection tasks and high‑precision end‑measure checks. Which material is used for the gauge pin and what does that mean for wear? The gauge pin is made of special steel, a balanced material that offers good wear resistance for workshop use while maintaining dimensional stability during repeated checks. Is the gauge pin supplied ready for transport and storage? Yes, the M323.G21 is supplied in a protective case to reduce the risk of damage in transit and to help preserve the pin’s surface and dimensional integrity. For which inspection tasks is this gauge pin most suitable? This gauge pin is intended for compact end‑measure and plug‑gauge checks in workshop and production environments where a 16.21 mm nominal diameter and 50 mm engagement length provide repeatable, reliable results. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
16.22 mm Gauge Pin, Workshop Version, 50 mm Length - Metav IndustryLine
Benefit from a combination of high precision, robust workshop design and a compact 50 mm length for reliable end measurements; order the gauge pin directly via Metav Werkzeuge or consult our specialists for matching gauge sets. M323.G22 Gauge Pin – Ø16.22 mm, 50 mm length (Metav IndustryLine) A gauge pin intended for precise end‑measurement tasks in workshop and inspection environments, combining tight tolerance and durable construction Precision tolerance ±0.002 mm Special steel for workshop durability 50 mm overall length for end‑measurements Supplied as a single inspection pin Precision that secures process results The M323.G22 gauge pin is manufactured to a tolerance of ±0.002 mm, a level that supports fine comparative checks and reduces uncertainty in pass/fail decisions. Such accuracy ensures that gauging tasks yield reproducible results when used with calibrated fixtures or comparator systems. The numerical tolerance indicates the maximum permitted deviation from nominal; keeping this within a few micrometres helps avoid rejects caused by measurement variation rather than part non‑conformity. This rational performance argument directly benefits quality control throughput by lowering rework rates. Durable workshop design for repeatable end measurements A compact construction with a diameter of 16.22 mm and length of 50 mm provides a practical balance between reach and stiffness for end‑measurement scenarios. The pin is made from special steel, selected for wear resistance and dimensional stability under typical workshop handling. The modest mass supports fast handling and placement in jigging or checking fixtures, improving cycle times during routine inspections. As a single‑unit inspection implement, it fits into modular gauge sets or bespoke holders where repeatability and surface integrity matter. Simple integration into inspection routines and traceability Identifiable by SKU M323.G22 and GTIN, the pin can be tracked within catalogues and inventory systems for consistent replacement or matched to inspection plans. The individual supply format facilitates selective stocking of specific diameters without bulk kits, aiding workshops that require precise end‑measurements across a range of bore or shaft checks. Paired with calibrated reference blocks or ring gauges, this inspection pin becomes part of a reliable metrology workflow that supports production control and audit trails. For specification matching, availability and advice on gauge selection, contact Metav Werkzeuge—Metav IndustryLine specialists are available to recommend compatible sets and fixtures Technical Data SKU: M323.G22 GTIN: 4061905069116 Weight: 0.15 kg Material: Special steel Facts Diameter: 16.22 mm Length: 50 mm Tolerance: ±0.002 mm Special features Workshop version Single inspection/gauge pin Suitable for end‑measurements FAQ What is the primary application for this gauge pin? The gauge pin M323.G22 is intended for end‑measurement checks and comparative inspection tasks where a compact, stiff pin of 16.22 mm diameter and 50 mm length is required. How tight is the dimensional tolerance of the pin? This inspection pin is produced to a tolerance of ±0.002 mm, enabling fine discrimination in quality control processes. Can the pin be used in standard gauge holders and fixtures? Yes, the M323.G22 gauge pin is suitable for integration into modular holders and fixtures designed for individual inspection pins. What material is used and what benefit does it provide? Made from special steel, the pin offers wear resistance and dimensional stability under typical workshop conditions, supporting repeatable measurements. How is the item identified for ordering and inventory? The product is listed under SKU M323.G22 and GTIN 4061905069116 for straightforward procurement and stock management. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
16.23mm Gauge Pin, Single, 50mm Length, Workshop Version - Metav IndustryLine
Take advantage of the combination of industrial‑grade special steel, high repeatability with ±0.002 mm tolerance, and compact dimensions for precise end‑size verification in production and inspection. Order the item directly via Metav Werkzeuge or consult the Metav team for specification matching and supply. Gauge Pin M323.G23 – Single test pin, Ø 16.23 mm, 50 mm (Metav IndustryLine) A gauge pin (M323.G23) engineered for precise end‑size verification and inspection tasks in workshop and assembly environments. High precision ±0.002 mm tolerance Solid special steel construction Diameter Ø 16.23 mm, length 50 mm Workshop version with transport case Precision for reliable end‑size checks The gauge pin delivers ±0.002 mm tolerance, providing a dependable reference for go/no‑go and end‑size inspections where repeatability matters. Designed for direct use at the inspection bench, the pin offers a measurable benefit to quality control processes: fewer rejects and faster decision cycles when checking bore sizes or mating features. The tight tolerance is presented in a compact form, allowing efficient use in production sampling and incoming inspection tasks without compromising measuring confidence. Sturdy material and workshop design for long service life Constructed from special steel, this test pin is intended for robust, everyday workshop use. The material choice balances hardness and wear resistance to sustain repeated insertions and withdrawals during batch inspection. The workshop execution includes reinforced handling surfaces so the tool withstands frequent use; this reduces downtime and the need for early replacement, supporting continuous, predictable inspection routines in metalworking and assembly operations. Compact dimensions that suit fine mechanical tasks With a diameter of Ø 16.23 mm and overall 50 mm length the pin sits within the micro range (10–100 mm) category, making it particularly well suited for fine mechanical and precision engineering tasks. The compact size keeps the instrument stiff under hand use and simplifies positioning in small bores and close‑tolerance features. This dimensional balance helps to deliver the best compromise between reach and rigidity for workshop‑level metrology, especially when space or access is limited. Practical handling, traceability and safe delivery The single test pin is presented as a ready‑to‑use inspection device with clear identification M323.G23 for inventory and traceability. At 0.15 kg the pin is easy to handle and to integrate into an inspection kit or gauge set. For protected transport and storage the item is supplied in a case suitable for workshop environments, which helps to maintain geometry and surface condition while in transit or when stored between uses. The overall concept supports effective, repeatable measurements at the point of inspection. For consistent end‑size control choose the Metav IndustryLine M323.G23 gauge pin and contact Metav Werkzeuge for tailored delivery, technical matching and prompt supply from Emmerich. Technical data SKU: M323.G23 GTIN: 4061905069123 Material: Special steel Accuracy: ±0.002 mm Weight: 0.15 kg Numbers Diameter: 16.23 mm Length: 50 mm Weight: 0.15 kg Tolerance: ±0.002 mm Special features Single test pin Workshop execution Supplied in transport case Special steel construction Micro range (10–100 mm) FAQ What tolerance does the gauge pin offer? The Metav IndustryLine gauge pin M323.G23 is manufactured to a tolerance of ±0.002 mm, suitable for precise end‑size verification. Is this pin suitable for regular workshop use? Yes, the workshop execution and special steel material make the M323.G23 robust enough for frequent, routine inspections. For which applications is the pin intended? The pin is intended for end‑size checking, reference measurements and bore verification in assembly and inspection workflows. How is the pin delivered and stored? The single test pin M323.G23 is supplied in a transport case to protect geometry and surface condition during storage and transport. What identification should be used when ordering or stocking this pin? Use SKU M323.G23 and the Metav IndustryLine designation for ordering and inventory management. Metav IndustryLine: Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
16.24 mm Gauge Pin Single, 50 mm Length, Workshop Version - Metav IndustryLine
Take advantage of the combination of high repeatability, robust special‑steel construction and compact form for reliable end‑measure checks in workshop environments. Order the test pin directly via Metav Werkzeuge or contact our consultants for application advice. Test pin M323.G24 — 16.24 mm diameter, 50 mm length (Workshop version) The Test pin M323.G24 is a precision inspection pin designed for end‑measure checks and fixture gauging in workshop and inspection settings. Workshop version for robust use Diameter 16.24 mm for precise fits High accuracy ±0.002 mm tolerance Made from special steel for wear resistance Precision where small tolerances matter The inspection pin delivers repeatable measurements thanks to its tight tolerance of ±0.002 mm, equivalent to 2 µm. This level of accuracy positions the component for tasks that require microscopic conformity between mating parts, such as final end‑dimension checks and go/no‑go seating in jigs. The compact 50 mm length and the defined 16.24 mm diameter allow integration into common fixture holders and measurement stacks without excessive overhang, reducing measurement uncertainty caused by flex or misalignment. Designed for workshop endurance and handling Built as a workshop version, the pin combines a hardened profile with a corrosion‑resistant finish from special steel, providing stable contact faces under frequent use. The modest mass (approx. 0.15 kg) aids handling and placement while ensuring sufficient mass to resist micro‑vibrations during manual inspection routines. Where durability matters, the material choice and machining quality lower wear rates and keep repeatability high across inspection cycles. Practical application and compatibility The component suits end‑measure inspection, fixture alignment and repeat checks in production and maintenance operations. Its geometry is optimised for seated positioning in gauge blocks, test stands and bespoke holding fixtures used in routine quality control. Where precise seating and repeatability are required, this inspection pin reduces setup time and minimises rework by providing a stable datum that is easy to reference during comparative measurements. Care, traceability and integration notes Routine maintenance is straightforward: keep contact faces clean and free of debris, protect against corrosive environments and inspect periodically for wear that could affect the ±0.002 mm specification. For complex setups, combine the pin with calibrated gauge blocks or fixtures to preserve traceable measurement chains and to document conformity in inspection reports. For tailored integration advice, Metav’s technical team can suggest compatible holders and mounting routines used in similar workshop contexts. For reliable end‑measurement performance and application support, request availability from Metav Werkzeuge—Metav’s specialists in Emmerich will advise on compatibility and delivery for the M323.G24 test pin. Technical data SKU: M323.G24 GTIN: 4061905069833 Label: Test pin, single, 16.24 mm, length 50 mm Manufacturer: Metav IndustryLine Eclass: 21170231 Facts Diameter: 16.24 mm Length: 50 mm Accuracy: ±0.002 mm Weight: 0.15 kg Special features Workshop version (Werkstatt‑Ausführung) Material: special steel Story trigger: end‑measure application FAQ What is the exact diameter of the pin? The inspection pin has a diameter of 16.24 mm, specified for precise seating and fixture use. What tolerance can be expected during inspection? The pin is manufactured to an accuracy of ±0.002 mm, ensuring high repeatability for end‑measure checks. Which material is used for the pin? The component is made from special steel, chosen for wear resistance and stable contact performance. Is the pin suitable for fixture and end‑measure applications? Yes, the M323.G24 test pin is designed specifically for end‑measure checks and fixture gauging in workshop environments. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
16.25mm Gauge Pin 50mm Length Workshop Version - Metav IndustryLine
Reliable end-size verification and fast routine checks are achieved by combining a 16.25 mm nominal diameter with a fine ±0.002 mm accuracy and a robust 50 mm length, ensuring repeatable results on the shop floor; Order the test pin directly via Metav Werkzeuge or ask our consultants if needed. Test pin M323.G25 — 16.25 mm diameter, 50 mm length (Metav IndustryLine) Test pin M323.G25 is a precision gauging pin designed for routine end-size checks and dimensional control in machine shops and toolrooms. Precision ±0.002 mm accuracy Nominal diameter 16.25 mm 50 mm length for secure handling Special steel, workshop version Fast, reliable end-size verification for production flow The gauging pin offers a straightforward method for checking final diameters and end measures with consistent repeatability. With a 16.25 mm nominal size and a declared accuracy of ±0.002 mm (±2 µm), this instrument is suited to quick pass/fail inspections and comparative checks on production parts. The compact 50 mm shaft length keeps handling convenient while providing sufficient engagement depth for many workpieces. In practice, the device reduces inspection time by enabling immediate verification at the bench or in-process checkpoints, supporting tighter process control and fewer downstream rework cycles. Robust construction that withstands workshop routines Built as a workshop version, the pin is manufactured from special steel selected for wear resistance and dimensional stability during repetitive use. The solid construction and balanced mass (approx. 0.15 kg) aid in firm placement and reduce wobble during tactile checks. For everyday inspection tasks, the combination of material choice and compact geometry translates into longer service life and consistent contact conditions. Where routine gauging is required, a reliable pin such as this lowers the risk of measurement variation caused by tool deformation or surface damage. Suitable contexts and practical benefits for the quality workflow Intended for end-size verification, the pin supports a wide range of quality-assurance applications in metalworking and component assembly. The fine tolerance of ±0.002 mm enables close control in toolrooms, small-batch manufacturing and final inspection stations where micrometre-level deviations matter. The item is supplied individually for immediate integration into inspection sets; traceability is supported via the SKU M323.G25 and GTIN 4061905069840, facilitating inventory and quality documentation. Use of the pin complements micrometres, bore gauges and optical comparators, providing a simple, durable reference for dimensional conformance. Contact Metav Werkzeuge for procurement advice on the M323.G25 gauging pin and ensure dependable end-size control for the workshop environment Technical Data Article number: M323.G25 GTIN: 4061905069840 Manufacturer: Metav IndustryLine Facts Diameter: 16.25 mm Length: 50 mm Accuracy: ±0.002 mm Weight: 0.15 kg Special features Material: Special steel Workshop execution Supplied individually for inspection use Intended use: End-size verification FAQ What is the declared accuracy of this gauging pin? The gauging pin M323.G25 is specified with an accuracy of ±0.002 mm (±2 µm), suitable for fine workshop inspections and comparative checks. For which tasks is the M323.G25 best suited? This test pin is ideal for end-size verification, quick pass/fail checks and supplemental dimensional control alongside micrometres and bore gauges. What material is used for the pin and why? The pin is made from special steel, chosen to provide durability and stable contact surfaces under repetitive use in workshop conditions. Is the item supplied individually or as part of a set? The product is supplied individually and ready for immediate use in inspection routines or for addition to existing gauging sets. How does the M323.G25 support traceability in quality processes? Traceability is facilitated via the SKU M323.G25 and GTIN 4061905069840, which assists in inventory control and documentation within quality-management systems. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
16.26 mm Test Pin, Single, 50 mm Length, Workshop Version - Metav IndustryLine
Take advantage of a compact, workshop-grade gauge pin that combines high repeatability, ±0.002 mm dimensional accuracy and a 50 mm stem for reliable end‑measure verification; the robust special steel construction ensures stability under regular shop use. Order the test pin directly via Metav Werkzeuge or contact our advisors for application support. Test pin M323.G26 — 16.26 mm gauge, 50 mm length (Metav IndustryLine) The Test pin M323.G26 is a workshop-grade measuring pin designed for precise end‑dimension checks and quick insertion gauging in production and inspection environments. Workshop‑grade construction and finish Diameter 16.26 mm for end‑measure applications 50 mm stem length for stable engagement High repeatability with ±0.002 mm accuracy Engineered for repeatable end‑dimension checks This gauge pin delivers consistent results for small‑bore and end‑measure verification thanks to a closely controlled diameter of 16.26 mm and a tight tolerance of ±0.002 mm. The compact design reduces leverage and deflection during manual handling, so each measurement is more reproducible. Where repeatability is critical—such as incoming inspection or short‑run production control—the combination of a precise nominal diameter and a robust stem length reduces rework and speeds decision making on the shop floor. Durable materials and shop‑floor practicality Manufactured from special steel, the pin resists wear and maintains geometry under routine use, extending service life compared with softer gauges. The 50 mm length provides ample engagement depth for many end‑measure checks while keeping mass low (approx. 0.15 kg) for easy handling. Supplied in a dedicated transport case to protect the measuring surface during storage and transit, the item is optimised for workshop conditions and repetitive use, where handling safety and surface protection matter as much as dimensional precision. Integration into inspection workflows and traceability As a single‑piece gauge for insertion and comparative checks, the pin simplifies go/no‑go tests and reference verifications within fixtures and checking jigs. The compact form factor allows integration into bench fixtures or portable kits for in‑place checks. For procurement and inventory, the article is listed under the measuring pins category and carries GTIN details for traceability. When a stable, workshop‑oriented gauge is required to complement existing inspection sets, this pin provides a pragmatic balance of precision, durability and ease of use. Contact Metav Werkzeuge for specification matching and procurement of the Metav IndustryLine test pin M323.G26 — phone +49 2822 7131930 or info@metav-werkzeuge.com Technical data Article number: M323.G26 GTIN: 4061905069857 Description: Test pin, single, 16.26 mm, 50 mm length Manufacturer: Metav IndustryLine Dimensions & performance Diameter (nominal): 16.26 mm Length: 50 mm Accuracy variation: ±0.002 mm Weight: 0.15 kg Materials & features Material: special steel Workshop execution Delivered in a transport case Category: measuring pins FAQ What is the intended use for this gauge pin? The test pin M323.G26 is intended for end‑dimension verification, insertion gauging and comparative checks in workshop and inspection environments. How precise is the diameter of the pin? The diameter is manufactured to 16.26 mm with an accuracy variation of ±0.002 mm, providing high repeatability for small‑bore measurements. Is the pin protected for transport and storage? Yes, the gauge pin is supplied in a transport case to protect the measuring surfaces during handling and storage. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
16.27mm Gauge Pin 50mm Length Workshop Version, Special Steel - Metav IndustryLine
Take advantage of the combination of workshop-grade construction, special steel and ±0.002 mm tolerance for dependable end‑dimension control; order the gauge pin directly via Metav Werkzeuge or consult our specialists for application advice. Gauge pin, single Ø16.27 mm, 50 mm length — workshop-grade precision pin from Metav IndustryLine The Gauge pin, single Ø16.27 mm, 50 mm is a cylindrical precision gauge designed for end‑dimension inspection and reference checks in workshop metrology and fixture set‑up. Workshop-grade execution for daily shop use Diameter Ø16.27 mm with ±0.002 mm accuracy Made from special steel for long-term wear resistance Built for reliable end‑dimension checks Engineered for repeatable measurements, this precision pin combines a workshop-grade finish with a special steel shaft to resist wear during routine use. The nominal diameter Ø16.27 mm and the verified deviation of ±0.002 mm make the pin suitable as a high‑accuracy reference for end‑dimension control and pass/fail checks. Because the design focuses on stability and cylindrical form, readings remain consistent when used as a datum or in alignment tasks, reducing rework and inspection time. Fits inspection workflows and tooling fixtures Compact and straightforward to handle, the pin integrates into go/no‑go assemblies, fixture set‑up, and comparative inspection routines. Supplied as a single cylindrical gauge with 50 mm length, it occupies minimal bench space while offering sufficient engagement length for many clamping and locating situations. Delivery includes a protective case, which preserves the ground surface during transport and storage and simplifies organisation of inspection kits in a busy workshop. Durable precision for daily workshop use The combination of a hardened surface and careful machining yields notable wear resistance, supporting long service intervals in production environments. Metav IndustryLine parts are curated through a central quality filter in Emmerich, ensuring consistent dimensional conformity across batches. For operations seeking a robust reference pin without the complexity of custom gauges, this precision cylinder provides a pragmatic balance between accuracy and everyday usability. Contact Metav Werkzeuge today to discuss whether the Metav IndustryLine gauge pin suits your inspection bench — our Emmerich team will advise on delivery options and technical fitment. Technical Data SKU: M323.G27 GTIN: 4061905069864 Article description: Gauge pin, single, Ø16.27 mm, length 50 mm Brand: Metav IndustryLine Facts Diameter: 16.27 mm Length: 50 mm Tolerance / deviation: ±0.002 mm Weight: 0.15 kg Special features Material: special steel Workshop execution Delivery in protective case Single precision gauge pin FAQ What applications is this gauge pin intended for? This gauge pin is intended for end‑dimension inspection, fixture alignment and go/no‑go reference tasks; the Metav IndustryLine single pin is suited to workshop metrology and tooling checks. Does the pin include a calibration certificate? No specific calibration certificate is indicated for this gauge pin; it is supplied to the stated manufacturing tolerance of ±0.002 mm without an accompanying calibration report. Is the Ø16.27 mm size compatible with standard locating holes and bushes? Yes, the Ø16.27 mm diameter is compatible with standard locating features; the pin’s Ø16.27 mm cylindrical form provides a reliable reference for mating holes and bushings. What protection is provided during transport and storage? The gauge pin is delivered in a protective case to safeguard the ground surface during transport and to keep the pin organised within an inspection kit. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
16.28mm Gauge Pin 50mm Length Workshop Version, Special Steel - Metav IndustryLine
Take advantage of precise, workshop-grade measuring with the combination of ±0.002 mm accuracy and a robust special steel construction; the compact 50 mm length and protective transit case support repeatable end-dimension checks. Order the gauge pin directly via Metav Werkzeuge or contact the consultants for delivery and handling options. Metav IndustryLine Gauge pin M323.G28 — single test pin, Ø 16.28 mm, length 50 mm A Metav IndustryLine Gauge pin M323.G28 designed for precise end-dimension inspection and workshop use, offering a compact 50 mm working length and workshop-grade robustness High-precision tolerance ±0.002 mm Workshop design for everyday handling Delivered in a protective transport case Material: special steel for wear resistance High-precision measurements for repeatable end-dimension checks The M323.G28 is specified with an accuracy of ±0.002 mm, providing the repeatability required for end-dimension verification and fine gauging tasks. The defined tolerance supports reliable decisions in quality control and first-article inspection, where consistent results matter. Constructed from special steel, the pin combines wear resistance with dimensional stability under standard workshop conditions, reducing the need for frequent replacements and ensuring stable measurements over time. Robust handling and transport-safe design that protects the gauge With a 50 mm pin length and a compact mass of 0.15 kg, this single test pin balances manoeuvrability and stiffness for short-span checks. The workshop execution emphasises ease of handling during frequent use; edges and faces are designed for secure seating in fixtures. Delivery in a protective transport case minimises risk of transit damage and supports straightforward storage in a toolbox or inspection cabinet, so the gauge remains ready for reliable use on the shop floor. Practical application: efficient checks and process integration Designed as a dedicated tool for end-dimension and plug-type checks, the gauge pin suits routine inspection of bore diameters, plug fits and assembly checks in production and maintenance workflows. The compact format speeds throughput during sampling and reduces set-up time compared with larger gauging systems, delivering a tangible productivity benefit. Backed by the Metav approach to quality and supply, this workshop-grade component forms part of a dependable inventory strategy for workshops and small series production. Contact Metav Werkzeuge in Emmerich for delivery details, case options and assistance with integrating the Metav IndustryLine M323.G28 gauge pin into existing inspection routines Technical data Article number: M323.G28 GTIN: 4061905069871 Category: Messstifte Label: Prüfstift, einzeln, 16,28 mm Länge 50 mm Facts Diameter: 16.28 mm Length: 50 mm Accuracy: ±0.002 mm Weight: 0.15 kg Special features Material: Special steel Workshop execution Delivered in protective transport case SKU: M323.G28 FAQ Is the gauge pin suitable for routine bore inspections in a workshop environment? The M323.G28 gauge pin from Metav IndustryLine is intended for workshop use and is well suited to routine bore and fit checks thanks to its compact 50 mm length and robust construction. What tolerance can be expected from this test pin? The gauge pin is specified with an accuracy of ±0.002 mm, enabling tight control for end-dimension verification. Which material is used for the M323.G28 and what are the benefits? The M323.G28 is manufactured from special steel, offering improved wear resistance and dimensional stability for repeated use. Is the gauge pin supplied ready for transport and storage? Yes, the M323.G28 is delivered in a protective transport case to reduce the risk of damage in transit and to simplify storage on the shop floor. Does the delivery include an ISO 17025 calibration certificate? The M323.G28 is supplied with standard factory inspection; an ISO 17025 calibration certificate is not included with this item. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
16.29mm Gauge Pin 50mm Length Workshop Version, Special Steel - Metav IndustryLine
Take advantage of the combination of workshop-grade robustness, fine mechanical accuracy and compact handling for reliable end‑measurements in daily production. Order the item directly via Metav Werkzeuge or ask the consultants at Metav Werkzeuge for application advice. Test Pin M323.G29 – Gauge pin with 16.29 mm diameter and 50 mm length (Metav IndustryLine) A Test Pin M323.G29 designed for precision end‑measurements, alignment and inspection tasks in workshop environments. Workshop version, robust construction Diameter 16.29 mm, precision fit Length 50 mm, compact handling Accuracy ±0.002 mm for fine checks Precise measurement where it matters This gauge pin delivers high positional accuracy for end‑measurements and datum transfers. With a nominal diameter of 16.29 mm and an indicated variation of ±0.002 mm, the component provides repeatable fits for plug‑and‑go inspection routines. Constructed from special steel, the pin resists deformation under normal handling and retains geometry for prolonged service life. Such specification supports quality assurance processes that rely on small, verifiable tolerances rather than estimation. Compact design for fast workshop handling The 50 mm overall length and low mass (0.15 kg) mean the pin is simple to manoeuvre and integrate into jigs, fixtures or handheld inspection tools. Its compact format reduces setup time in serial checks and eases positioning in confined bores or stepped components. The workshop‑oriented execution prioritises durability and ergonomics, ensuring that routine verification remains efficient without specialised handling tools. Integration into quality workflows and practical benefits As a single test pin, the component suits inspection stations that require a defined reference for end‑face checks, alignment of mating parts, or verification of hole diameters where a controlled contact geometry is needed. The robust material choice and fine tolerance make the item suitable for repeated use in production environments, supporting consistent results and traceable measurement records. Confidence in measurement contributes directly to lower rework rates and steadier process output, reinforcing the practical advantages of a well‑specified gauge pin. For workshop‑grade precision from Metav IndustryLine, contact Metav Werkzeuge for a tailored supply recommendation and fast delivery from Emmerich to ensure the right test pin is available for current production needs. Technical data SKU: M323.G29 GTIN: 4061905069888 Weight: 0.15 kg Material: Special steel Diameter: 16.29 mm Length: 50 mm Accuracy: ±0.002 mm Numeric data Diameter (nominal): 16.29 mm Length (overall): 50 mm Mass: 0.15 kg Tolerance/variation: ±0.002 mm Special features Workshop execution Single test pin for end‑measurements Robust construction for repetitive use Metav IndustryLine product family FAQ What are the exact dimensions of this test pin? The Test Pin M323.G29 (Metav IndustryLine) has a nominal diameter of 16.29 mm and an overall length of 50 mm; SKU M323.G29. Which material is the pin made from? The item is manufactured from special steel, chosen for dimensional stability and resistance to wear in workshop use. What accuracy can be expected during inspection? The gauge pin is specified with a variation of ±0.002 mm, enabling fine checks and repeatable fits. For which tasks in the workshop is this pin suited? The pin is intended for end‑measurements, alignment, datum transfers and checking hole fits where a precise, fixed contact geometry is required. Can this pin be used with standard fixtures and holders? Yes; the nominal diameter and straight tolerance make the pin compatible with common gauge holders and fixture inserts used for repetitive inspection workflows. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
16.2mm Gauge Pin Length 50mm Workshop Version - Metav IndustryLine
Take advantage of precision, robust workshop design and proven material quality to secure reliable end measurements. With a combination of tight tolerance and solid construction, this gauge pin streamlines go/no‑go checks and dimensional control; order or request application advice via Metav Werkzeuge for rapid clarification. Gauge pin M323.G20 — single test pin, diameter 16.2 mm, length 50 mm (Metav IndustryLine) The gauge pin M323.G20 is a single test pin designed for precise end measurements and fit verifications in workshop and inspection settings, offering a compact measuring solution for routine dimensional control. Gauge pin, diameter 16.2 mm, length 50 mm Accuracy ±0.002 mm for tight tolerances Workshop version in special steel Engineered for consistent, repeatable results The core advantage is measurement repeatability: with a declared tolerance of ±0.002 mm, the pin supports tight tolerance checks and reliable go/no‑go testing where dimensional certainty matters. The compact geometry and 50 mm shank length reduce bending effects during short‑range end measurements, helping to keep readings consistent from one operator to the next. For production environments that require straightforward verification of mating bores or end dimensions, this tool provides a measurable gain in process stability and inspection throughput. Robust construction for everyday workshop use Manufactured from special steel and delivered as a workshop version, the pin resists wear in frequent handling and is suitable for routine inspection benches. The moderate mass (approx. 0.15 kg) and solid feel make manual alignment and insertion predictable, reducing setup time during repetitive checks. Built to withstand daily use, the design focuses on practical longevity rather than delicate laboratory handling, so maintenance is minimal and downtime is reduced — a practical saving for busy machining and assembly stations. Integrates into quality workflows with low overhead This single test pin fits naturally into established dimensional control procedures and can serve as a calibrated reference for end‑measurement routines and fit verification. The clear identification via SKU M323.G20 and traceable GTIN simplifies inventory and documentation. Combined with Metav’s supply chain and technical support, the pin helps standardise inspection points across multiple workstations, supporting consistent quality documentation and faster fault isolation when parts deviate from specification. For tight‑tolerance checks and reliable workshop verification, request the Metav IndustryLine gauge pin M323.G20 from Metav Werkzeuge or consult our specialists at +49 2822 7131930 or info@metav-werkzeuge.com Technical data SKU: M323.G20 GTIN: 4061905069093 Manufacturer: Metav IndustryLine Facts Diameter: 16.2 mm Length: 50 mm Tolerance: ±0.002 mm Weight: 0.15 kg Special features Material: Special steel Workshop version Single test pin for end measurements FAQ What is the declared measurement tolerance of this gauge pin? The declared tolerance for the Metav IndustryLine gauge pin M323.G20 is ±0.002 mm, making it suitable for tight tolerance checks and repeatable go/no‑go inspections. Which material is used for the pin and what are the benefits? The pin is made from special steel, chosen for wear resistance and durability in workshop environments; this supports frequent use with limited maintenance. For what applications is this test pin intended? The test pin is optimised for end measurements and fit verification in machining, assembly and inspection tasks where precise diameter checks and mating tests are required. How is the product identified for ordering and documentation? The product is listed under SKU M323.G20 and GTIN 4061905069093, facilitating stock management and traceability within quality documentation. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
16.31mm Test Pin Single 50mm Length Workshop Version - Metav IndustryLine
Take advantage of the combination of ±0.002 mm tolerance, robust special steel construction and transport-safe packaging for reliable inspection results; order the gauge pin directly via Metav Werkzeuge or ask the consultants for application advice. Gauge pin, single, Ø16.31 mm — 50 mm length (Metav IndustryLine) A gauge pin Ø16.31 mm, 50 mm long for precise end‑measure verification and fixture checking in workshop and inspection environments Single gauge pin Ø16.31 mm, length 50 mm High-precision tolerance ±0.002 mm Made from special steel, workshop version Supplied in a transport case Precise tolerance for repeatable inspection results The single test pin delivers a high-precision nominal diameter of Ø16.31 mm with a verified tolerance of ±0.002 mm, enabling consistent pass/fail checks and dimensional verification in production or quality control. This accuracy reduces ambiguity at the inspection stage and shortens decision loops when validating bores, gauging fixtures or end dimensions. The compact 50 mm shank length facilitates access into common fixture depths while keeping handling straightforward during repetitive sampling. Robust construction for workshop conditions Manufactured from special steel, the pin is designed as a workshop version to cope with routine use on the shop floor. The material choice supports stable dimensional behaviour under normal handling and machining‑adjacent environments, while the solid design minimises deformation risk during repeated gauge applications. Because the item is supplied in a transport case, storage and movement between workstations are simplified and the pin remains protected against incidental damage or contamination. Streamlining inspection workflows in production The gauge pin fits into standard inspection routines for components and fixtures where a defined limit or reference diameter is required. Its single‑piece design and clear diameter marking help to reduce set‑up time on control benches and inspection jigs, contributing to faster throughput without sacrificing measurement confidence. When integrated into routine checks, the pin supports efficient quality assurance and helps to maintain consistent assembly and machining outcomes across batches. For dependable metrology tools from a proven partner, choose Metav IndustryLine gauge pins and contact Metav Werkzeuge for tailored supply and technical guidance from Emmerich. Technical data Article number: M323.G31 GTIN: 4061905070129 Weight: 0.15 kg Diameter: 16.31 mm Length: 50 mm Tolerance: ±0.002 mm Material: Special steel Facts Category: Gauge pin / test pin Version: Single piece, workshop execution Packing: Transport case included SKU: M323.G31 Special features Precision workshop design Suitable for fixture and bore checking Short shank for accessible measurements FAQ What is the exact diameter and tolerance of this gauge pin? The gauge pin has a nominal diameter of 16.31 mm with a stated tolerance of ±0.002 mm, suitable for precise pass/fail and verification tasks. Is the pin protected during transport and storage? Yes, the Metav IndustryLine gauge pin is supplied in a transport case to protect the tool during movement and storage. Which material is used for the pin and what does that mean for workshop use? The pin is made from special steel; this provides robust mechanical behaviour for routine workshop applications and stable dimensional performance under normal handling. Can the gauge pin be used for fixture set‑up and bore verification? The test pin is intended for fixture and bore checking as a repeatable reference; its 50 mm length allows access to common inspection depths. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
Fast, tactile checks where electronics are impractical
Gauges and test pins provide unequivocal go/no-go results for threads, bores, gaps and radii without relying on electronics. The range covers plug gauges and ring gauges for internal and external threads, feeler gauges and precision feeler strips for micro‑gap assessment, plus probe pins and measuring pins for tactile diameter and pitch checks.
How these tools work in the production environment
Mechanical gauges operate as direct reference standards: a plug gauge or ring gauge verifies conformity to thread profiles and mating ability, while limit gauges separate accept from reject in a single step. Test pins are used to tactilely measure small bore diameters, centre‑to‑centre distances and radii. Manufactured from hardened gauge steel or ceramic and often precision lapped, these instruments deliver immediate physical results that are ideal for incoming inspection, machine‑side checks and final control.
Measurable benefits that affect production performance
- Reduced scrap and rework through rapid, unambiguous pass/fail assessment.
- Increased repeatability thanks to very low measurement uncertainty and fine lapping.
- Lower downtime: quick checks at the machine save cycle time and reduce setup periods.
- Durable construction with high wear resistance from specialised, low‑distortion alloys.
- Versatile delivery formats: individual gauges, organised sets in wooden cases or metre‑length feeler rolls compliant with DIN 2269.
Why Metav is the practical choice for precision supplies
Metav combines decades of expertise with a broad warehouse and quality filtering from Emmerich. As a precision partner for industry, craft and trade, Metav supplies a comprehensive selection of gauges and test pins alongside complementary tools such as precision calipers and setting rings. With over 48,000 customers and a catalogue exceeding 250,000 items, Metav is positioned to supply reliably, reduce vendor complexity and support traceable quality control to national standards.
Summary
Gauges and test pins are indispensable for dependable, repeatable quality assurance where tactile, mechanical verification is preferred. Choose these plug gauges, ring gauges, feeler strips and probe pins when immediate, robust measurement decisions are required on the shop floor.
FAQ
What materials are gauges and test pins typically made from?
Gauges and test pins are usually manufactured from hardened gauge steel for durability and wear resistance; ceramic variants are available where thermal stability and minimal wear are critical.
How do thread gauges ensure mating capability?
Thread plug gauges and ring gauges check flank diameters and thread form against standards, providing a clear go/no‑go verdict that confirms pairability with mating parts.
Which tolerance class should I choose for probe pins and gauge sets?
Select tolerance classes aligned with your inspection requirements; for high‑precision tasks, sets produced to DIN 2269 or equivalent tolerance classes ensure micrometre‑level control and repeatability.
Can feeler gauges measure contact gaps in valve and engine work reliably?
Yes. Feeler gauges and precision feeler strips, supplied either as a fan or metre‑length rolls, allow accurate assessment of valve clearances and contact gaps down to micrometre increments.
How do limit gauges speed up in‑process inspection?
Limit gauges separate good from bad in a single, tactile operation, enabling rapid go/no‑go checks at the machine and reducing both inspection time and the likelihood of human interpretation errors.
Fragen zu diesen Produkten??
Mit mehr als 30 Jahren Erfahrung beraten wir Sie gerne persönlich.
Tel.: +49 2822 7131930
Mail: info@metav-werkzeuge.com