Precision gauge blocks and plug gauges for reliable dimensional control
Mechanical gauge blocks and plug gauges are essential for tactile verification of threads, bores and gap dimensions, providing fast, unambiguous go/no-go results that enhance process reliability and reduce scrap. Designed for industrial metalworking and toolmaking, these precision tools support incoming inspection and final quality checks by delivering traceable measurements in applications such as thread inspection, bore diameter testing and spacing checks. Manufactured from specially hardened, low-distortion alloys and fine-lapped for minimal measurement uncertainty, the range includes thread plug gauges, precision plug gauges and calibration gauge blocks to ensure long-term repeatability and wear resistance.
0.69mm Gauge Pin Single ±0.001mm 50mm Length Workshop Finish - Metav IndustryLine
Take advantage of the combination of ultra‑fine diameter 0.69 mm, tight tolerance ±0.001 mm and workshop‑grade durability for precise end‑measure checks. Order the gauge pin directly via Metav Werkzeuge or consult the Metav team for application guidance. Test Pin M323.069 — Gauge pin, 0.69 mm diameter, ±0.001 mm tolerance (Metav IndustryLine) The Test Pin M323.069 is a precision gauge pin designed for fine end‑measure verification, toolsetting and fixture checks in workshop and inspection environments Diameter 0.69 mm, tolerance ±0.001 mm 50 mm hardened shaft for stable reference length Workshop‑grade design for frequent use Supplied in a protective transport case Precision that reduces reject rates The core advantage of this gauge pin is its exceptional tolerance of ±0.001 mm, which provides a verifiable reference for critical fits and finish checks. Such fine accuracy minimises uncertainty in pass/fail decisions, helping to reduce downstream rejects and rework. Where components have tight bore or pin clearances, a stable reference pin with 0.69 mm nominal diameter allows repeatable verification of hole diameters and seating fits. The tolerance quoted corresponds to high‑precision workshop grade measurement tools and supports reliable statistical process control when used as a comparative standard. Robust workshop design for everyday use Manufactured from special steel and offered in a workshop version, this gauge pin balances surface hardness and corrosion resistance with the handling demands of a production environment. The 50 mm shaft length delivers a usable reach for many fixture and assembly checks while the low mass supports quick positioning without operator fatigue. Supplied in a protective transport case, the pin is ready for secure storage and safe movement between inspection bench and machine tool, preserving the reference surface and ensuring repeatable results over numerous cycles. Practical integration and traceability As a compact gauge pin, this tool fits naturally into inspection routines, gauge sets and customised jigs for repeat checks of small bores, alignment pins and end‑measure verification. The product is identified by SKU M323.069 and GTIN for traceable stock management and ordering. Using a dedicated gauge pin as a reference reduces measurement chain complexity: compared with ad hoc mandrels, a certified precision pin delivers consistent contact geometry and measurable uncertainty, which improves both day‑to‑day decision making and auditability in quality records. For assured small‑bore measurement and fixture setting, choose the Metav IndustryLine test pin M323.069 — contact Metav Werkzeuge for technical advice, availability or to discuss suitable gauge sets at info@metav-werkzeuge.com or by phone on +49 2822 7131930 Technical data Article number: M323.069 GTIN: 4061905055102 Manufacturer: Metav IndustryLine Core specifications Diameter: 0.69 mm Tolerance: ±0.001 mm Length: 50 mm Weight: 0.003 kg Material: Special steel Special features Workshop version for frequent use Supplied in a protective transport case Category: Gauge pins / Messstifte Precision grade suitable for fine inspection work FAQ What is the primary use of this gauge pin? The Metav IndustryLine test pin M323.069 is intended for end‑measure verification, small‑bore checks and toolsetting where a stable reference diameter of 0.69 mm and tight tolerance is required. Is the pin suitable for repeated workshop handling? Yes, the workshop version is manufactured from special steel and supplied in a protective transport case to withstand regular use and to preserve the measuring surface. How is the product identified for ordering and stock control? The item is listed under SKU M323.069 and GTIN 4061905055102 for unambiguous ordering and inventory tracking. Can this gauge pin be used in fixture alignment tasks? Yes, the compact diameter and 50 mm length make it suitable as a reference in fixtures and jigs for alignment and pass/fail checks. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
0.6mm Gauge Pin Length 50mm ±0.001mm Workshop Version - Metav IndustryLine
The combination of high repeatability, a 0.60 mm diameter and an ultra-fine ±0.001 mm tolerance provides reliable reference measurements for precision workshops; benefit from durable special‑steel construction and compact 50 mm length for tight bores. Order the gauge pin directly via Metav Werkzeuge or contact the consultants for application advice. M323.060 Gauge pin – 0.60 mm diameter, ±0.001 mm tolerance (Metav IndustryLine) The M323.060 gauge pin is a compact precision reference pin for fine bore verification and end‑measure tasks in workshop metrology, designed for routine inspection and assembly control. Diameter 0.60 mm with ±0.001 mm accuracy 50 mm hardened special steel shaft Workshop version for robust everyday use Compact size for fine bore and micro applications Consistent precision for quality assurance As a tightly specified reference element, the gauge pin delivers ±0.001 mm conformity that supports repeatable pass/fail decisions in inspection workflows. The extremely small 0.60 mm diameter, combined with the short 50 mm length, minimises bending and run‑out, making the pin particularly suited to fine‑mechanical checks and gauging of small bores. For production environments where interchangeability and first‑time quality matter, the dimensional stability of the pin reduces rework and shortens inspection cycles. Engineered for routine workshop use Manufactured from special steel with a workshop configuration, the pin balances wear resistance with ease of handling during frequent use. The compact design and hardened shaft provide a robust reference that resists deformation under normal contact measurement stresses. This construction translates into longer service intervals and dependable behaviour when used in bench measuring stations, pin gauges, or as a reference in small‑component assembly jigs. Fast integration into metrology sets and fixtures The small footprint of the pin simplifies its incorporation into inspection benches and dedicated gauge assemblies. As a standard reference element, it complements gauge blocks, micrometres and dial indicators within a calibrated inspection chain. The clear numeric specification and material designation facilitate traceability in documentation and ensure coherent selection when building sets for micro‑production, watchmaking, miniature components or precision plumbing of assemblies. Contact Metav Werkzeuge today to secure the M323.060 gauge pin for precision bore checks and ensure consistent inspection results across workshop and production environments Technical data Article number: M323.060 GTIN: 4061905054129 Brand: Metav IndustryLine Facts Diameter: 0.60 mm Length: 50 mm Tolerance: ±0.001 mm Weight: 0.003 kg Special features Material: special steel Design: workshop execution Application: precision bore and end‑measure verification FAQ What inspection tasks is this gauge pin suitable for? The M323.060 gauge pin is intended for precision verification of very small bores and fits, serving as a reference in fine‑mechanical inspection and micro‑assembly routines. How does the ±0.001 mm tolerance affect measurement reliability? A tolerance of ±0.001 mm gives a clearly defined acceptance band for pass/fail checks; the M323.060 gauge pin therefore reduces ambiguity in go/no‑go decisions during quality control. Can the pin be used in automated gauge fixtures? Yes. The compact 0.60 mm diameter and short 50 mm length allow integration into automated or semi‑automated gauging setups where small reference elements are required. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
0.7 mm Test Pin Single, ±0.001 mm Accuracy, 50 mm Length, Workshop Version - Metav IndustryLine
High-precision 0.70 mm probe pin with a ±0.001 mm tolerance and a 50 mm shaft provides reproducible reference points for fine inspection tasks; workshop-grade special steel and delivery in a transport case ensure robust handling and safe storage. Order the probe directly via Metav Werkzeuge or consult our product specialists for application advice. M323.070 Probe pin (single) – 0.70 mm, ±0.001 mm, 50 mm by Metav IndustryLine The M323.070 is a single precision probe pin designed for fine dimensional checks and end‑measure reference points in workshop inspection setups. Precision tolerance ±0.001 mm Diameter 0.70 mm for micro measurements 50 mm special steel shaft Delivered in transport case Micrometre‑level precision for reliable reference measurements A diameter of 0.70 mm combined with a tolerance of ±0.001 mm delivers micrometre‑level accuracy for repeatable reference points. This level of precision supports consistent pass/fail decisions in inspection routines where small deviations matter. The tight tolerance is particularly advantageous when establishing end‑measure references or checking small bores and features that require a stable contact point; the manufacturing tolerance reduces measurement uncertainty and improves traceability in routine checks. Workshop‑grade construction for durability and stable handling Manufactured from special steel and offered as a workshop version, the probe pin is engineered for everyday use in inspection benches and gauge fixtures. The 50 mm shaft provides enough engagement for secure positioning while remaining compact for confined setups. Finished surfaces and material selection minimise wear and help preserve the nominal diameter over repeated use, so the component remains a dependable reference element in tool rooms and production inspection stations. Safe transport and straightforward replacement in fixtures Supplied as a single unit and delivered in a transport case, the probe pin is protected against impact and contamination during storage and transport. The compact weight and form factor make it simple to keep as a spare or replacement part in a measurement kit. Clear article identification and traceable GTIN facilitate inventory management and ensure the correct pin is used when calibrating or preparing inspection equipment. For workshop-ready micrometre accuracy from Metav IndustryLine, request the M323.070 probe pin via Metav Werkzeuge GmbH or consult our specialists at info@metav-werkzeuge.com / +49 2822 7131930 Technical data Article number: M323.070 GTIN: 4061905055119 Category: Messstifte Facts Diameter: 0.70 mm Length: 50 mm Tolerance: ±0.001 mm Weight: 0.003 kg Special features Material: Special steel Workshop version Delivered in transport case Single probe pin FAQ What tolerance does the probe pin offer? The M323.070 probe pin is specified with a tolerance of ±0.001 mm. What is the exact diameter and length of the pin? The probe pin has a diameter of 0.70 mm and a shaft length of 50 mm. Is the pin supplied ready for transport? Yes, the unit is delivered in a transport case to protect the pin during storage and movement. For which inspection tasks is this pin suitable? The small diameter and tight tolerance make the pin suitable for fine dimensional checks and end‑measure reference points in workshop inspection routines. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
0.71mm Gauge Pin, ±0.001 mm, 50 mm Length, Workshop Version - Metav IndustryLine
Take advantage of high-repeatability inspection with a 0.71 mm diameter pin that delivers ±0.001 mm accuracy and a practical 50 mm length, combining precision, compactness and robust workshop suitability—order directly via Metav Werkzeuge or consult the team for application advice. Gauge pin M323.071 — single precision gauge pin, Ø 0.71 mm, ±0.001 mm A Gauge pin M323.071 designed for fine dimensional checks and end‑measurement tasks in inspection and assembly environments Precision tolerance ±0.001 mm Diameter 0.71 mm for fine bores Length 50 mm for deep checks Made from special steel alloy Delivered in protective case Faster, more reliable inspection through submicrometre accuracy A compact inspection pin with a ±0.001 mm tolerance provides the measurable basis for dependable pass/fail assessments and repeatable checks. The combination of a slim 0.71 mm diameter and a 50 mm working length makes the pin well suited to verification of small bores and end measurements, reducing cycle time for high‑volume checks. The precise tolerance lowers uncertainty during fit inspection and supports consistent assembly decisions, which in turn helps maintain production flow and cut rework rates. Robust construction for regular workshop use Manufactured from special steel, this workshop‑grade gauge pin is engineered for frequent handling without sacrificing form stability. The workshop version specification prioritises a balance between wear resistance and straightness, allowing reliable use in inspection benches and portable test rigs. For secure transport and on‑site protection the pin is supplied in a protective case, ensuring the reference surface remains clean and undamaged between uses and simplifying storage in tool cabinets or instrument sets. Practical handling, simple integration and clear application focus The single‑piece design keeps handling straightforward and the low mass aids quick placement when inspecting small components; the listed weight reflects its compact nature. Its geometry is optimised for end measurements and the verification of fine holes and fits, making it a useful addition to gauge sets, pin blocks and small‑parts test fixtures. The specification suits quality control loops where fine bore verification and consistent repeatability are required for assembly acceptance and product compliance. Contact Metav Werkzeuge for tailored advice on the Metav IndustryLine M323.071 and to confirm availability from our Emmerich stock — call +49 2822 7131930 or email info@metav-werkzeuge.com Technical data SKU: M323.071 GTIN: 4061905055126 Material: Special steel Length: 50 mm Diameter: 0.71 mm Accuracy: ±0.001 mm Weight: 0.003 kg Facts Length (numerical): 50 mm Diameter (numerical): 0.71 mm Tolerance (numerical): ±0.001 mm Weight (numerical): 0.003 kg GTIN (numerical): 4061905055126 Special features Workshop version Single gauge pin for fine bore checks Delivered in protective transport case Category: Gauge pins Story trigger: end measurements FAQ What are the exact specifications of this gauge pin? The Metav IndustryLine gauge pin M323.071 has a diameter of 0.71 mm, a length of 50 mm and an accuracy of ±0.001 mm. Is the pin suitable for end measurements of small bores? Yes, the M323.071 is intended for end measurements and fine bore verification where a slim, precise pin is required. How is the gauge pin supplied for transport and storage? This gauge pin is delivered in a protective case to keep the reference surfaces secure during transport and storage. Can the pin be used in pin blocks or fixture assemblies? The single‑piece design is compatible with pin blocks and small fixture layouts, providing a practical geometry for integration in inspection setups. Which brand manufactures this gauge pin? The M323.071 is part of the Metav IndustryLine range and is supplied by Metav Werkzeuge for industrial metrology applications. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
0.72mm Test Pin Single ±0.001mm Length 50mm Workshop Finish - Metav IndustryLine
Take advantage of the combination of laboratory-grade ±0.001 mm repeatability, compact 0.72 mm diameter and a 50 mm working length for fast, reliable reference checks in the workshop; order directly via Metav Werkzeuge or ask the consultants for tailored advice. Gauge pin M323.072 — precision test pin, 0.72 mm diameter, ±0.001 mm, 50 mm length (Metav IndustryLine) The Gauge pin M323.072 is a single precision test pin designed for reference measurements and end‑dimension inspection in workshop metrology, supplied as a workshop‑grade item for routine use. High‑precision ±0.001 mm tolerance 50 mm workshop‑grade working length Solid special‑steel construction for durability Supplied in a protective transport case Accuracy that stabilises production decisions A tolerance of ±0.001 mm positions this test pin among high‑precision reference tools suitable for dimensional spot checks and fixture verification. The excellent repeatability reduces measurement scatter and supports decisive accept/reject judgements on incoming parts or subassemblies. Thanks to the fine diameter of 0.72 mm, the pin is ideal for verifying small bores, alignment holes and pin gauges where micrometre‑level variation matters. The measurable benefit for production is quicker go/no‑go decisions and fewer costly reworks. Built for workshop rhythms and frequent handling The workshop configuration emphasises robust everyday use: the pin is manufactured from special steel, offering wear resistance and consistent contact geometry over many cycles. At a 50 mm working length the pin balances access to internal features with handling comfort, and the light mass supports fast positioning during repetitive checks. Supplied in a protective transport case, the item remains protected between uses, ensuring the measurement surface stays clean and true — a practical advantage for busy shops where tool damage or contamination would otherwise impair accuracy. Simple integration into inspection routines As a single‑point reference, this test pin fits easily into established inspection workflows for jigs, fixtures and gauge blocks. It complements handheld gauges and bench fixtures for quick dimensional verification and can be used as a reference in assembly alignment tasks. The compact geometry makes it especially useful for checking small bore concentricity and positional tolerances. Clear, measurable performance means less subjective judgement during inspection and more repeatable results across operators. Transparency and traceable identification for inventory control The part is identified by SKU M323.072 and GTIN 4061905055430, simplifying stock management and ensuring traceability in procurement records. Lightweight and compact, the pin is convenient to store and to include in inspection sets or kitting for specific production lines. Metav’s role as a precision partner supports reliable supply from Emmerich, backed by broad product availability and a quality filter for European customers — an assurance for operations that rely on consistent instrument performance. Contact Metav Werkzeuge for advice on integrating the Metav IndustryLine gauge pin M323.072 into inspection routines and to arrange delivery from our Emmerich facility — email info@metav-werkzeuge.com or call +49 2822 7131930 Technical Data Article number: M323.072 GTIN: 4061905055430 Brand: Metav IndustryLine Dimensions & Precision Diameter: 0.72 mm Length: 50 mm Accuracy: ±0.001 mm Weight: 0.003 kg Materials & Features Material: Special steel Version: Workshop execution Packaging: Protective transport case FAQ What size of bore is this gauge pin suitable for? The gauge pin M323.072 has a diameter of 0.72 mm and is intended for verifying small bores, alignment holes and pin gauge checks in workshop metrology. Does the pin come ready for immediate use out of the box? Yes, the Metav IndustryLine gauge pin M323.072 is supplied as a single, ready‑to‑use test pin in a protective transport case suitable for workshop handling. How does the ±0.001 mm tolerance affect daily inspection? A ±0.001 mm tolerance provides high‑precision reference performance that reduces measurement uncertainty during routine checks, enabling clearer go/no‑go decisions and fewer remeasurements. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
0.73mm Gauge Pin Single ±0.001mm Length 50mm Workshop Version - Metav IndustryLine
Take advantage of the combination of ±0.001 mm accuracy, a 0.73 mm diameter for fine‑bore checks and a 50 mm shaft made from special steel to ensure repeatable end‑measurements; order the test pin directly via Metav Werkzeuge or consult our specialists for application advice. Test pin M323.073 — Gauge pin, 0.73 mm diameter, ±0.001 mm accuracy (Metav IndustryLine) The test pin M323.073 is a workshop‑grade gauge pin designed for precise end‑measurements, fit checks and inspection tasks where small diameters require stable reference pins ±0.001 mm high‑precision tolerance 0.73 mm diameter for fine measurements 50 mm hardened special‑steel shaft Workshop version with protective case Accurate results for tight tolerances The compact gauge offers a ±0.001 mm tolerance that delivers high repeatability for small‑bore inspections and go/no‑go checks. As a finely finished reference pin, it reduces measurement uncertainty during comparative checks and plug gauges, helping to secure process capability in quality inspections. The controlled tolerance is a rational advantage when validating bore fits or validating tool wear, because precise reference geometry directly reduces rework and rejects. Robust workshop design and handling benefits Built as a workshop version, the pin combines a 50 mm hardened shaft with corrosion‑resistant special steel to withstand regular handling on the shop floor. The compact geometry and finished end faces enable reliable seating in fixtures and micrometres, while the supplied protective case preserves the datum surfaces during transport. This construction prioritises operational uptime and lowers the need for frequent replacement, supporting efficient workflow in production and maintenance environments. Practical application and compatibility Engineered for end‑measurements and fit verification, the gauge pin suits small‑bore gauges, jigs and inspection benches where accurate reference pins are needed. The 0.73 mm nominal diameter makes the pin ideal for fine‑mechanical assemblies and precision valve or nozzle inspections. Its slim profile simplifies insertion into tight features and ensures consistent contact without disturbing the component, which is particularly useful for repetitive dimensional checks in batch production. Contact Metav Werkzeuge for tailored advice on integrating the M323.073 into inspection routines and for reliable, local supply from our Emmerich facility Technical data Article number: M323.073 GTIN: 4061905055447 Brand: Metav IndustryLine Material: Special steel Facts Diameter: 0.73 mm Tolerance: ±0.001 mm Length: 50 mm Weight: 0.003 kg Special features Workshop execution Delivered in protective case for transport Single test pin for end‑measurement tasks Story trigger: end measurements FAQ What diameter and tolerance does the pin offer? The gauge pin has a diameter of 0.73 mm and a tolerance of ±0.001 mm, making the M323.073 suitable for precise small‑bore checks. Is the pin suitable for workshop use and repeated handling? Yes. The workshop execution and special steel shaft are designed for routine use; the supplied protective case preserves the measuring faces between operations. For which inspection tasks is this pin intended? It is intended for end‑measurements, fit checks and fine‑bore verification where a slim, accurate reference pin is required. Does the product include a protective container for transport? Yes, the pin is supplied in a protective case appropriate for safe transport and handling. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
0.74mm Gauge Pin, Single, ±0.001mm Accuracy, Length 50mm, Workshop Version - Metav IndustryLine
Take advantage of the combination of workshop-grade durability, ±0.001 mm accuracy and compact dimensions for reliable end-size checks; order or discuss application details with Metav Werkzeuge for a smooth inspection workflow. Gauge pin, single, 0.74 mm, ±0.001 mm, length 50 mm (Metav IndustryLine) A Gauge pin, single, 0.74 mm, ±0.001 mm, length 50 mm for high-precision end-measurements and plug checks in inspection benches and toolrooms High-precision ±0.001 mm tolerance Diameter 0.74 mm for micro measurements 50 mm special steel shaft for workshop use Supplied in protective transport case Reduce measurement uncertainty with micrometre-grade tolerance This test pin delivers a ±0.001 mm tolerance that significantly reduces uncertainty in small-diameter inspections. For micro-scale control, the 0.74 mm diameter provides a precise reference for bore checks, end-size verification and go/no-go procedures. The extremely fine tolerance means less rework and higher process stability when used as a reference gauge in quality control routines. The compact format suits tight fixtures and minimises influence from handling and fixture play. Workshop-ready construction for repeatable handling Designed as a workshop-grade single gauge pin, the component is manufactured from special steel to combine surface finish and resistance appropriate for frequent use. The 50 mm length keeps the pin stiff enough for stable contact while remaining compact for inline inspection. Supplied individually in a protective transport case, the pin is protected during storage and transit, preserving the measuring surface and ensuring repeatable readings when placed into gauges or measuring fixtures. Easy integration into inspection workflows and traceable stock Lightweight at approximately 0.003 kg and supplied as a single reference item, the pin fits directly into plug gauge sets, depth gauges and fixture inserts for end-size control. The clear SKU documentation enables straightforward inventory and procurement: M323.074 is ready for integration into standard inspection lists or calibration schedules. Where traceability is required, the product data and packaging facilitate labelling and record-keeping for regular checks and quality audits. Contact Metav Werkzeuge to discuss whether the Metav IndustryLine gauge pin M323.074 meets specific inspection requirements or to request a technical quotation by e‑mail at info@metav-werkzeuge.com or by phone on +49 2822 7131930 Technical Data Article number: M323.074 GTIN: 4061905055454 Label: Gauge pin, single, 0.74 mm, ±0.001 mm, length 50 mm Numbers / Core technical data Diameter: 0.74 mm Tolerance: ±0.001 mm Length: 50 mm Weight: 0.003 kg Special features Material: special steel Workshop-grade execution Supplied in protective transport case Category: Gauge pin / test pin Story trigger: end measurements FAQ How precise is this gauge pin for inspection use? The M323.074 gauge pin provides a precision of ±0.001 mm, making it suitable for micrometre-level end-size checks and tight tolerance plug gauging. Is the gauge pin delivered with a calibration certificate? Calibration is not specified in the product data; the gauge pin is supplied as a workshop-grade single pin in a protective case without an explicit calibration certificate. What applications suit this 0.74 mm pin? The pin is intended for small-bore verification, end-measurements and use in fixture-based plug checks in toolrooms and inspection benches; it functions as a precision reference for micro measurements. What is included in the delivery? Delivery includes the single gauge pin (M323.074) and a protective transport case to prevent damage during storage and transit. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
0.75mm Test Pin Single ±0.001mm Accuracy 50mm Length, Workshop Version - Metav IndustryLine
The combination of a 0.75 mm diameter, a ±0.001 mm tolerance and a 50 mm length delivers highly repeatable end‑measurements while remaining practical for daily workshop use; robust special steel construction and protective packaging ensure durability and safe transport. Order the M323.075 directly via Metav Werkzeuge or consult the technical team for application guidance. M323.075 gauge pin — 0.75 mm, ±0.001 mm, 50 mm (Metav IndustryLine) M323.075 is a single gauge pin designed for precision end‑measure checks and fixture set‑up in workshop environments Workshop design for routine checks Diameter 0.75 mm for fine features Tolerance ±0.001 mm for high precision Made from special steel, robust finish Precision where repeatable measurements matter The core advantage of this inspection pin is its tight manufacturing tolerance: ±0.001 mm. Such accuracy makes it a reliable reference for end‑measurement tasks and quality checks where minimal deviation is critical. Manufactured to consistent dimensional stability, the pin serves as a calibrated reference for gauging small bores, verifying finished feature limits and checking tool run‑out. By specifying a slender 0.75 mm diameter combined with a 50 mm length, the component balances the need for access into narrow features with sufficient engagement length to reduce measurement scatter. This focus on reproducibility supports efficient in‑line checks and helps maintain process control in serial production. Built for regular workshop use and easy handling The workshop version construction emphasises robustness and handling ease under daily use. Produced from special steel, the pin resists wear and retains its geometry during routine contact with jigs and workpieces. Its low mass contributes negligible inertia during placement yet provides a stable feel when seating in fixtures. Supplied in a protective case, the component is ready for safe transport and storage, reducing the risk of nicks that would compromise accuracy. The compact form factor facilitates quick exchange in inspection setups and minimises downtime when multiple reference sizes are employed. Practical integration with fixtures and measuring kits As an inspection or reference pin for end‑measuring and fixture alignment, this component integrates smoothly into assembly aids, go/no‑go sets and verification benches. The geometry and tolerance profile make it suitable for end‑measure checks, reference alignment of small assemblies and precision positioning of gauging fixtures. Where compact reference points are required, the slender diameter allows access into confined features while the defined length provides a consistent datum. Use in combination with micrometres, dial indicators or bench gauge blocks yields a traceable measurement chain for production records. Supply reliability and workshop confidence Sourced under the Metav IndustryLine, the pin reflects a production approach that balances industrial standards with practical workshop needs. The brand’s distribution model supports reliable availability and centralised quality filtering from Emmerich, ensuring components arrive in measured condition and with consistent characteristics. For purchasers seeking a durable, high‑accuracy reference pin for routine inspection tasks, this component offers a pragmatic mix of precision, handling and supply security—attributes that sustain efficient throughput in metalworking and mechanical assembly contexts. For workshop‑grade reference components, request the M323.075 from Metav Werkzeuge — Metav Werkzeuge can be contacted via info@metav-werkzeuge.com or by telephone on +49 2822 7131930 for order details and technical clarification. Technical Data Article number: M323.075 GTIN: 4061905056031 Weight: 0.003 kg Diameter: 0.75 mm Length: 50 mm Tolerance: ±0.001 mm Material: Special steel Version: Workshop Packaging: Supplied in protective case Facts Mass: 0.003 kg Diameter nominal: 0.75 mm Length nominal: 50 mm Tolerance specification: ±0.001 mm Special features Intended use: End‑measure checks and fixture set‑up Construction: Workshop execution for daily use Finish: Durable surface suitable for repeated contact Category: Gauge pin / inspection pin FAQ What diameter and tolerance does this gauge pin offer? The M323.075 gauge pin is manufactured with a 0.75 mm diameter and a tolerance of ±0.001 mm, providing a high‑precision reference for small‑feature measurements. Which material is used for the pin? The M323.075 is made from special steel, selected for wear resistance and dimensional stability during regular inspection tasks. Is the pin supplied with protective packaging? The product is supplied in a protective case suitable for transport and storage, reflecting the workshop‑oriented design. For which applications is this inspection pin intended? This reference pin is intended for end‑measure checks, fixture alignment and verification of small bores or feature limits in machining and assembly environments. Does the product data include a calibration certificate? The available product data do not specify an included calibration certificate; calibration status is not detailed in the standard product information. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
0.76mm Test Pin Length 50mm ±0.001 mm, Workshop Version - Metav IndustryLine
Take advantage of the combination of ±0.001 mm repeatability, a compact Ø 0.76 mm diameter and a stable 50 mm length to secure reliable end‑measurements in micromechanical production; order the gauge pin directly via Metav Werkzeuge or contact our consultants for application advice. M323.076 Gauge pin – Ø 0.76 mm, ±0.001 mm, 50 mm | Metav IndustryLine A M323.076 gauge pin designed for high‑precision end‑measurements and inspection tasks in workshop environments. High‑precision tolerance ±0.001 mm Diameter 0.76 mm for micromeasurements Length 50 mm for stable contact Workshop‑grade special steel construction Precision engineered for micromeasurements The compact Ø 0.76 mm diameter combined with a tolerance of ±0.001 mm positions this gauge pin in the micro range of inspection tools, where minimal form and dimensional variation matter. Such a tight specification reduces measurement uncertainty when checking small bores, fine shafts or end faces; the result is reproducible pass/fail decisions and fewer downstream reworks. The geometry and tolerance serve as the basis for precise end‑measurements in micromechanics and fine‑tolerance assembly. Durable material and workshop readiness Manufactured from special steel, the pin has been configured as a workshop version to withstand routine handling and frequent contact with mating surfaces. The material choice provides wear resistance and stable contact performance over many cycles, supporting consistent measurement results in production environments. The single‑piece design ensures straightforward mounting in gauge fixtures or use as a reference pin during bench inspections, contributing to reliable process control. Practical use and inspection benefits This compact gauge pin integrates easily into manual inspection routines, comparator set‑ups or plug‑gage stacks where small diameters must be verified quickly. The 50 mm length gives a balanced contact surface without excess overhang, aiding alignment and operator control. As a single gauge pin, it is ideal for targeted checks and for establishing fixed reference points during assembly or incoming inspection, improving throughput by simplifying decision steps in quality control. For workshop‑grade precision from Metav IndustryLine, request availability of the M323.076 through Metav Werkzeuge by e‑mail at info@metav-werkzeuge.com or by phone on +49 2822 7131930 Technical data SKU: M323.076 GTIN: 4061905056048 Label: Gauge pin, single, 0.76 mm, ±0.001 mm, length 50 mm Facts Diameter: 0.76 mm Tolerance: ±0.001 mm Length: 50 mm Weight: 0.003 kg Special features Material: Special steel Workshop version Single piece Category: Gauge pins FAQ How precise is this gauge pin? The M323.076 gauge pin offers a tolerance of ±0.001 mm, suitable for micron‑level checks in fine mechanical inspection. Which applications suit this pin best? Its compact diameter and high precision make the pin ideal for micromechanics, small‑bore verification and end‑face inspection in workshop and bench environments. Is the pin delivered as a single item? Yes, the product is supplied as a single gauge pin for targeted inspection tasks and fixture use. What material is used for the pin? The M323.076 is made from special steel, chosen for wear resistance and consistent contact behaviour in frequent inspection cycles. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
0.77mm Test Pin Length 50mm ±0.001mm Workshop Version, Special Steel - Metav IndustryLine
Take advantage of the micron-level accuracy and compact handling of this precision test pin to secure repeatable end‑dimension checks and reliable gauge fixtures; the combination of a 0.77 mm diameter, ±0.001 mm tolerance and a 50 mm length supports consistent production control and easy integration into inspection setups — order via Metav Werkzeuge or consult the Metav team for application advice. Test pin M323.077 — Single precision gauge pin, 0.77 mm, ±0.001 mm (Metav IndustryLine) The Test pin M323.077 is a single precision gauge pin designed for end‑dimension inspection and plug‑gauge routines in workshop and metrology environments. Single precision test pin 0.77 mm diameter Tolerance ±0.001 mm for high accuracy 50 mm length for stable probing Workshop version in special steel Micron‑level accuracy for dependable inspections This gauge pin provides a ±0.001 mm tolerance, which corresponds to micrometre‑level precision and supports strict quality control criteria on small bores and critical end dimensions. The small 0.77 mm diameter and fine manufacturing tolerances reduce measurement uncertainty when used as a reference or in go/no‑go checks, enabling operators to document repeatable results and to minimise downstream rework. As a compact precision element, it suits applications where consistent plug‑fit verification is mandatory. Stable handling and repeatability in production With a 50 mm overall length the pin offers a good balance between handling comfort and probing stability. The slender geometry is particularly useful for checking narrow bores, pin holes and counterpart locating features where a controlled insertion depth and straightness are required. The lightweight construction also reduces the influence of operator handling during manual checks, contributing to faster inspection cycles and fewer false rejects in series production. Material choice geared to workshop demands Manufactured from special steel, the pin is specified for dimensional stability under normal workshop conditions. The material selection focuses on keeping geometric integrity during repeated seating in gauges and fixtures, so measurements remain consistent over time. The “workshop version” designation indicates a robust build intended for regular use alongside standard inspection tools in machine shops and assembly areas. Practical integration into inspection workflows At approximately 0.003 kg the pin is easy to manoeuvre and to install in small fixtures or comparator jigs without affecting balance. The single‑piece design simplifies cleaning and visual inspection between cycles. As a precision test pin it can be combined with standard gauge holders or used as a reference element in manual verification processes, supporting both random checks and routine production sampling. Contact Metav Werkzeuge in Emmerich for application guidance or to request this Metav IndustryLine precision gauge pin M323.077 for reliable end‑dimension inspection; phone +49 2822 7131930 or e‑mail info@metav-werkzeuge.com Technical data Article number: M323.077 GTIN: 4061905056055 Manufacturer: Metav IndustryLine Material: Special steel Numbers Diameter: 0.77 mm Length: 50 mm Tolerance: ±0.001 mm Weight: 0.003 kg Special features Workshop version Single precision test pin Designed for end‑dimension inspection FAQ What level of precision does this gauge pin provide? The gauge pin M323.077 (Metav IndustryLine precision test pin) offers a tolerance of ±0.001 mm, delivering micrometre‑class repeatability suitable for tight end‑dimension checks. For which applications is this pin most suitable? This precision measuring pin is intended for end‑dimension inspection, plug‑gauge verification and narrow bore checks where a 0.77 mm diameter reference is required. What material is used and why does it matter? The pin is produced from special steel to maintain dimensional stability during repeated use, which helps preserve measurement consistency in workshop conditions. How easy is the pin to handle and integrate into fixtures? With a 50 mm length and a weight of around 0.003 kg, the pin is lightweight and straightforward to install in small fixtures or comparator jigs for routine checks. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
0.78mm Precision Gauge Pin ±0.001mm Length 50mm, Workshop Finish - Metav IndustryLine
Taking advantage of workshop‑grade construction and ±0.001 mm accuracy, this gauge pin ensures reliable fit checks and end‑measure controls in fine‑tolerance assembly. Order the gauge pin directly via Metav Werkzeuge or consult our advisors for suitability and delivery. Gauge pin M323.078 — single precision test pin, 0.78 mm, ±0.001 mm, 50 mm length (Metav IndustryLine) The Gauge pin M323.078 is a compact, workshop‑grade precision test pin designed for fine gauging tasks and small‑bore inspections in manufacturing and quality control. ±0.001 mm tolerance for high precision 0.78 mm diameter for fine gauging 50 mm length for deep reach Workshop‑grade special steel construction Reduced rework through measurable precision High repeatability is central to efficient inspection workflows. With an accuracy of ±0.001 mm, this test pin provides a measurable reference that reduces uncertainty when verifying hole fits, dowel seats or mating parts. The narrow diameter and controlled tolerance minimise play during insertion, which aids decision‑making in go/no‑go checks and limits costly rework. The specified tolerance translates into predictable assembly behaviour, making the pin suitable for process control points where tight clearances determine final part acceptance. Compact dimensions that reach confined features The slim 0.78 mm diameter and 50 mm length combine to create a tool for confined inspection tasks. Its compact profile allows access to small bores and recessed features without the need for additional fixturing. Constructed in special steel with a workshop finish, the pin withstands repeated handling in production environments while maintaining dimensional integrity. The small mass and balanced geometry support stable insertion, which is particularly advantageous when gauging delicate components or when repeatability over many cycles is required. Seamless integration into inspection routines Designed as a single‑piece precision test pin, this item integrates easily into existing gauge sets, inspection benches and manual measurement procedures. It functions effectively for end‑measurement and fit verification, complementing micrometre and comparator checks by offering a direct physical reference. The pin's controlled diameter and length assist in spot checks during assembly and final inspection, helping to preserve process reliability and uphold quality documentation standards in routine production environments. For workshop‑grade precision from Metav IndustryLine, contact Metav Werkzeuge in Emmerich to confirm availability and specification fit for inspection tasks. Technical Data Article number: M323.078 GTIN: 4061905056062 Label: Gauge pin, single, 0.78 mm, ±0.001 mm, length 50 mm Weight: 0.003 kg Core specifications Diameter: 0.78 mm Length: 50 mm Tolerance: ±0.001 mm Mass: 0.003 kg Materials & special features Material: Special steel Workshop execution Accuracy rating: ±0.001 Single pin configuration FAQ What is the nominal diameter and length of this gauge pin? The nominal diameter is 0.78 mm and the overall length is 50 mm for the M323.078 gauge pin. How precise is the measurement tolerance of the pin? The M323.078 is specified with a tolerance of ±0.001 mm, suitable for high‑precision fit checks. For which tasks is this pin most suitable? This test pin is intended for end‑measure checks, small‑bore verification and fit assessments in assembly and inspection processes. What material is the pin made from and how does that affect use? The pin is made from special steel, giving workshop robustness and dimensional stability under regular handling. Can the pin be used as part of a gauge set or standalone for spot checks? The single‑piece configuration of M323.078 adapts well to both gauge sets and standalone spot checks in production and quality control. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
0.79mm Precision Gauge Pin Workshop Version 50mm Length ±0.001mm - Metav IndustryLine
Take advantage of the combination of absolute measuring precision, compact form and robust workshop design for reliable end‑measure checks. The ±0.001 mm tolerance, 0.79 mm diameter and 50 mm length ensure repeatable results in fine gauging tasks. Order directly via Metav Werkzeuge or contact the consultants for application advice. M323.079 Gauge Pin — Single 0.79 mm, ±0.001 mm, 50 mm (Metav IndustryLine) The M323.079 gauge pin is a workshop‑grade precision test pin designed for end‑measurement and fine gauging in inspection and production environments. Precision tolerance ±0.001 mm Diameter 0.79 mm for fine gauging 50 mm hardened special steel shaft Delivered in protective transport box Precision that supports reliable end‑measure decisions The gauge pin offers a declared tolerance of ±0.001 mm, which places it into the high‑precision category for workshop test pins. This level of accuracy provides a stable, measurable reference for end‑measure tasks and close‑tolerance checks, reducing ambiguity in pass/fail decisions. The slender 0.79 mm diameter is ideal where very small bores, pin gauges or fine features require verification; the combination of small cross‑section and micron‑level tolerance makes the component particularly useful in fine mechanics, toolmaking and precision assembly where consistent repeatability matters. Robust construction and practical protection for everyday workshop use Manufactured from special steel, the shaft balances surface hardness with dimensional stability to withstand repeated insertion and withdrawal during inspection cycles. The 50 mm length offers sufficient engagement for most end‑measure applications while keeping handling simple; the low mass supports quick positioning and minimal inertia. Delivery in a protective transport box preserves the measuring surface in transit and on the workbench, reducing the risk of nicks or contamination that would compromise accuracy. The workshop execution ensures a practical mix of durability and ease of use for routine quality checks. Clear application benefits and procurement confidence As a single, precision gauge pin in a workshop‑grade format, this item serves as a straightforward reference for end‑measure checks, go/no‑go fixtures and assembly verification. Its small diameter and tight tolerance make it suitable for checking plug fits, alignment dowels and fine bores. Procurement from Metav IndustryLine comes with the reassurance of established distribution and a European quality filter in Emmerich; this supports reliable supply and predictable stock management for production and inspection departments. For specific integration into measurement fixtures or to confirm suitability for a particular inspection task, technical advice is available through Metav Werkzeuge. For workshop-ready precision from Metav IndustryLine, contact Metav Werkzeuge for tailored advice—info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: M323.079 GTIN: 4061905056079 Material: Special steel Diameter: 0.79 mm Length: 50 mm Tolerance: ±0.001 mm Weight: 0.003 kg Version: Workshop execution Delivery: Protective transport box included Facts High precision: ±0.001 mm Small diameter for fine features: 0.79 mm Compact engagement length: 50 mm Very low mass: 0.003 kg Special features Single gauge/test pin design Suited for end‑measure and fine gauging Protective transport box for handling and transport Category: Gauge pins (Messstifte) FAQ What is the declared accuracy of the pin? The declared accuracy is ±0.001 mm, giving micron‑level repeatability for fine end‑measure checks with the M323.079 gauge pin. Which material is the pin made from? This gauge pin is manufactured from special steel, chosen for dimensional stability and resistance to wear in routine workshop use. Is the gauge pin supplied protected for transport? Yes. The item is supplied in a protective transport box (plastic or wooden), which preserves the measuring surface during shipment and handling. Can the pin be used as a reference in inspection fixtures? The workshop‑grade design of this test pin makes it suitable as a reference element in gauges and fixtures for end‑measure verification; specify calibration requirements if certified reference status is needed. Which measurement tasks are best suited to this pin? The combination of 0.79 mm diameter and ±0.001 mm tolerance suits fine bore checks, plug fits, alignment dowels and precise assembly inspections where small‑feature gauging is required. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
0.81mm Gauge Pin Length 50mm ±0.001mm Workshop Version - Metav IndustryLine
With a focus on repeatable inspection, the combination of ±0.001 mm tolerance, a 0.81 mm diameter and a 50 mm length delivers precise end‑measure verification in workshop environments; the robust workshop design and protective transport case keep the instrument ready for daily use. Order M323.081 directly via Metav Werkzeuge or contact our consultants for application advice. M323.081 gauge pin — 0.81 mm, ±0.001 mm, 50 mm (Metav IndustryLine) M323.081 is a single gauge pin designed for fine end‑measurement and bore verification in workshop inspection Workshop version for robust daily use Tolerance ±0.001 mm for high‑precision checks Diameter 0.81 mm for fine bore verification Supplied in protective transport case High‑precision verification that reduces rework The compact cylindrical pin offers a ±0.001 mm tolerance, which corresponds to a one‑micrometre allowance and supports critical fit checks where even small deviations cause assembly issues. With a 0.81 mm diameter, this instrument is tailored for narrow bores and fine components; the narrow profile minimises disturbance to the measured feature and helps achieve consistent results. The measurable benefit is lower scrap rates and fewer rework cycles, because measurement uncertainty is reduced by design. The pin’s light mass (3 g) and rigid geometry ensure stable contact during insertion, improving repeatability across successive measurements. Built for the workshop — durability and handling Delivered in a protective transport case, the workshop version is finished for everyday operation and handling. The special steel composition provides wear resistance suitable for repetitive checks while maintaining surface integrity where measurement reference is required. The 50 mm length balances reach and control: long enough to engage shallow bores and short enough to be guided steadily by hand or simple fixtures. This pragmatic construction means fewer interruptions in inspection workflows and a reliable tool for routine quality control in busy production areas. Practical applications and compatibility with inspection tasks Designed as a single gauge pin for end‑measure and plug checks, the instrument is suitable for toolroom verification, small‑batch inspection and final acceptance testing of precision components. Its dimensions make it appropriate for fine mechanical parts, precision connectors and features where sub‑millimetre accuracy is essential. The gauge pin’s simplicity supports integration with basic fixtures or manual comparators and provides a clear go/no‑go reference when detailed metrology equipment is not required. The result is an accessible precision tool that complements laboratory instruments and strengthens shop‑floor quality routines. For reliable measurement of fine bores, choose the Metav IndustryLine M323.081 gauge pin and contact Metav Werkzeuge in Emmerich for tailored technical advice and fast supply via info@metav-werkzeuge.com or +49 2822 7131930 Technical data Article number: M323.081 GTIN: 4061905057007 Manufacturer: Metav IndustryLine Facts Diameter: 0.81 mm Length: 50 mm Tolerance: ±0.001 mm Weight: 0.003 kg Special features Material: special steel Workshop version for daily use Supplied in protective transport case Single gauge pin for end‑measure checks FAQ What accuracy can be expected from this gauge pin? The M323.081 gauge pin is specified with a tolerance of ±0.001 mm, providing micrometre‑level accuracy suitable for precise end‑measure and plug verification. Which applications suit a 0.81 mm gauge pin? This diameter is ideal for checking small bores, fine mechanical components and precision connectors where sub‑millimetre verification is required. Is the instrument appropriate for repeated workshop use? Yes, the workshop version and the special steel construction are designed for frequent handling and inspection in production environments. Does the product come protected for transport and storage? The gauge pin is supplied in a protective transport case to reduce the risk of damage and to keep the measuring surface intact during handling. Can this pin be used together with simple fixtures or comparators? The single gauge pin format allows easy use with manual fixtures, comparators and basic inspection jigs for quick go/no‑go checks. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
0.82mm Test Pin 50mm Length ±0.001mm Workshop Version, Special Steel - Metav IndustryLine
Take advantage of the proven combination of industrial repeatability, workshop-hardy construction, and pinpoint diameter tolerance for reliable end‑size checks. Order the gauge pin directly via Metav Werkzeuge or consult our specialists for application advice. Gauge pin M323.082 — single workshop gauge pin with ±0.001 mm tolerance The Gauge pin M323.082 is a compact workshop-grade test pin for precise end-size verification and plug-fit checks in quality control and assembly. Workshop-grade construction for daily use Diameter tolerance ±0.001 mm for high repeatability Length 50 mm for compact inspection setups Special steel for long-term wear resistance Precision that removes doubt from small‑part inspection Engineered for tasks where even tiny deviations matter, this single gauge pin delivers ±0.001 mm diameter accuracy on a 0.82 mm nominal size. Such fine tolerance reduces uncertainty in pass/fail decisions during dimensional control and supports consistent comparative measurement between batches. The result is a measurable reduction in rework and fewer downstream assembly issues, translating into tangible efficiency gains for production and inspection processes. Robust material and workshop design for everyday handling Manufactured from special steel and presented in a workshop-oriented design, the pin resists wear and maintains geometry through repeated contact. A 50 mm shaft length keeps handling practical while preserving stiffness for repeatable results in tight jigs or fixture-based checks. The compact form factor suits bench inspectors and in-process verification alike, offering durability without the complexity of larger gauge systems. Easy integration into inspection routines and fixtures The compact single-pin format is ideal for end‑size checks, plug‑fit testing and use as a reference master in assembly stations. Thanks to the fine diameter control and low mass, it is straightforward to incorporate into manual gauges, comparison stands or dedicated fixtures. Traceable identification via the GTIN and SKU supports inventory management and quality documentation inside existing workflows and inspection plans. Contact Metav Werkzeuge today to discuss how the Metav IndustryLine gauge pin M323.082 can be deployed in current inspection setups or to request a tailored supply recommendation from our team Technical data Article number: M323.082 GTIN: 4061905057014 Brand: Metav IndustryLine Weight: 0.003 kg Facts Nominal diameter: 0.82 mm Diameter tolerance: ±0.001 mm Length: 50 mm Accuracy specification: ±0.001 mm Special features Workshop execution Single gauge pin for end‑size checks Material: special steel Category: Gauge pins (Messstifte) FAQ What is the intended use for this gauge pin? The gauge pin is intended for end‑size verification, plug‑fit checks and as a simple reference in inspection fixtures; the Metav IndustryLine gauge pin M323.082 is optimised for small‑diameter parts. How precise is the diameter control of the pin? Diameter control is stated at ±0.001 mm, giving the M323.082 the repeatability required for stringent pass/fail assessments on small features. Which material is the pin made from and what does that mean for wear? Manufactured from special steel, the pin offers improved wear resistance compared with untreated alloys, supporting longer service life in regular inspection tasks. Can the pin be used in jigs and fixtures for automated checks? Yes, the compact geometry and stable diameter tolerance make the pin suitable as a reference element in manual or semi‑automated fixtures for in‑process verification. How is the product identified for stock and documentation purposes? The product is listed under SKU M323.082 and GTIN 4061905057014, enabling clear traceability in procurement and quality records. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
0.83mm Gauge Pin, Single, ±0.001mm, Length 50mm, Workshop Version - Metav IndustryLine
Take advantage of the combination of extreme measuring precision, durable special‑steel construction and workshop‑ready packaging for reliable in‑process checks and reduced rework. Order the gauge pin directly via Metav Werkzeuge or consult the technical team for integration advice. M323.083 Gauge pin — 0.83 mm, ±0.001 mm, 50 mm length (Metav IndustryLine) The M323.083 is a single precision gauge pin designed for fine bore inspection and end‑measure verification in workshop environments. High‑precision ±0.001 mm tolerance Solid special‑steel construction 50 mm working length for stable handling Supplied in a transport case for safe storage Measure small bores with laboratory‑grade precision A compact, high‑accuracy pin for dimensional checks, the gauge pin delivers a tolerance of ±0.001 mm, equivalent to 1 µm, which places it in the class of ultra‑fine inspection tools. Such precision reduces the risk of false rejects and costly rework by providing repeatable go/no‑go verification of holes, seats and mating features. The specified 0.83 mm diameter is produced to tight form and roundness standards so that bore conformity can be assessed reliably during setups or batch checks. Durable design and workshop suitability for daily use Manufactured from special steel and offered in a workshop execution, this single pin withstands typical handling while retaining measurement integrity. The 50 mm length gives sufficient projection for insertion and stable handling without excessive lever arm that could introduce deflection. Delivery in a transport case protects the gauge during movement between inspection stations or jobsites and helps maintain nominal surface condition; the packaging is intended for transport safety rather than long‑term storage. Practical uses and integration into inspection routines The precision pin is suited to end‑measure checks, go/no‑go verification, and use as a reference for setting up gauges or fixtures. In routine quality control it functions as a direct, tactile method for assessing bore size and fit where optical or dimensional instruments are impractical. The M323.083 complements micrometre and calliper work by offering a simple, robust check that integrates into process control across small‑part production, toolmaking and precision assembly. Contact Metav Werkzeuge today for availability, batch information and advice on fitting the Metav IndustryLine M323.083 gauge pin into your inspection workflow Technical Data Article number: M323.083 GTIN: 4061905057021 Label: Prüfstift, einzeln, 0,83mm, +/- 0.001 mm Länge 50 mm SKU: M323.083 Manufacturer: Metav IndustryLine Special feature: Werkstatt‑Ausführung Delivery: transport case Facts Diameter: 0.83 mm Length: 50 mm Tolerance: ±0.001 mm Weight: 0.003 kg Special features Material: Special steel Single test pin Category: Gauge pins Intended for workshop inspection FAQ What degree of accuracy can be expected from this gauge pin? The M323.083 gauge pin is manufactured to a tolerance of ±0.001 mm, providing micrometric accuracy suitable for fine bore verification and precision inspection tasks. Is the pin suitable for production use in a workshop environment? Yes — the workshop execution and special steel construction make the gauge pin robust for everyday inspection routines while maintaining dimensional stability. How is the gauge pin supplied and protected during transport? The pin is supplied individually and comes in a transport case to protect the measuring surface and ensure safe handling between stations. Can this pin be used for setting up gauges or fixtures? The 0.83 mm diameter and stable 50 mm length make it suitable as a reference pin for fixture alignment, positional checks and go/no‑go verification in small‑part assemblies. Does the product include any certification or calibration document? No specific calibration certificate is listed with the product data; please contact Metav Werkzeuge for information on calibration options and traceability if required. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
0.84mm Test Pin, Single, ±0.001 mm, 50 mm Length, Workshop Version - Metav IndustryLine
Take advantage of a high‑precision measuring solution that combines ±0.001 mm accuracy with a compact 0.84 mm diameter and a robust 50 mm length for reliable end‑dimension checks; order the gauge pin directly via Metav Werkzeuge or consult our specialists for application advice. Gauge pin M323.084 — precision gauge pin 0.84 mm, ±0.001 mm (Metav IndustryLine) The Gauge pin M323.084 is a single, workshop‑grade measuring pin designed for precise end‑dimension inspections and assembly checks in metrology and production environments. Workshop-grade construction Diameter 0.84 mm, tolerance ±0.001 mm Length 50 mm for end-measurements Supplied in protective transport box Precision for repeatable end‑dimension checks The compact measuring pin delivers industrial‑grade repeatability thanks to its ±0.001 mm (1 µm) tolerance, which places it in the high‑precision band for gauge pins. A diameter of 0.84 mm provides accurate engagement in tight bores and reference holes, while the use of special steel ensures dimensional stability under normal workshop conditions. This combination reduces measurement uncertainty and supports tighter process control in inspection routines. Robust workshop design with secure handling Built as a workshop‑version item, the pin's 50 mm length gives sufficient reach for end‑face and through‑hole verification without compromising handling. Supplied as a single unit in a protective transport box, the pin arrives protected against transit damage and ready for immediate use on benches or fixtures. The compact mass of approximately 0.003 kg contributes to comfortable handling during repetitive checks and minimises the risk of accidental deflection. Improves inspection throughput and traceability Integrating a consistent small‑diameter gauge into routine checks shortens inspection time and reduces rework, supporting efficient production workflows. The M323.084 measuring pin is suitable for precision inspection steps within metrology workflows where repeatable end‑dimension verification is required. Backed by the Metav IndustryLine offering, the product benefits from a Europe‑centred quality filter that supports reliable supply for workshops and small‑scale industrial users. Contact Metav Werkzeuge to request the Metav IndustryLine M323.084 gauge pin for precise end‑dimension control; call +49 2822 7131930 or email info@metav-werkzeuge.com Technical data Article number: M323.084 GTIN: 4061905057038 Manufacturer: Metav IndustryLine Facts Diameter: 0.84 mm Length: 50 mm Tolerance: ±0.001 mm Weight: 0.003 kg Special features Workshop version Material: Special steel Supplied in transport box Single unit delivery FAQ What tolerance does this gauge pin offer? The M323.084 gauge pin offers a tolerance of ±0.001 mm (1 µm), suitable for high‑precision end‑dimension checks. What are the physical dimensions of the pin? Diameter 0.84 mm, length 50 mm, weight approx. 0.003 kg. What material is used for the pin? The pin is manufactured from special steel to provide stable dimensions for workshop use. Is this pin intended for workshop use? Yes, the product is a workshop‑version gauge pin designed for routine inspection and assembly checks. How is the product supplied and identified? Supplied as a single unit with article number M323.084 and GTIN 4061905057038. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
0.85mm Test Pin, Single, ±0.001mm Accuracy, 50mm Length, Workshop Version - Metav IndustryLine
Take advantage of the combination of micro‑scale accuracy and robust workshop construction for reliable go/no‑go checks; the 0.85 mm diameter and ±0.001 mm tolerance ensure repeatable inspections, while the 50 mm working length covers a wide range of fixture and component checks. Order the M323.085 directly via Metav Werkzeuge or ask our consultants for application guidance. M323.085 gauge pin — single test pin, 0.85 mm diameter, ±0.001 mm accuracy M323.085 is a single gauge pin designed for fine dimensional verification in workshop and production metrology, suitable for precise go/no‑go testing and end‑dimension checks. Precision tolerance ±0.001 mm Diameter 0.85 mm for micro checks Full 50 mm working length Hardened special steel construction Engineered for repeatable micro‑measurements The M323.085 delivers ±0.001 mm repeatability, making it suitable for high‑precision inspection tasks where minimal deviation is critical. That tolerance level places the pin in the high‑precision range used for fine mechanical parts and quality control loops. The small 0.85 mm diameter reduces probe interference in tight bores and ensures contact points remain localised, while the 50 mm length provides enough engagement for many fixture and assembly checks. This combination reduces rework and inspection time by delivering reliable, comparable readings across multiple measurement cycles. Practical advantages that speed up inspection workflows Supplied as a single, workshop‑grade test pin, this item integrates easily into manual inspection routines and semi‑automated test jigs. The compact diameter and extended length allow the gauge to be used for internal alignment checks, depth verification and end‑dimension control without extensive fixturing. By reducing the need for frequent set‑up changes, the pin contributes to faster throughput and fewer measurement errors. The robust construction also limits deformation during repeated handling, supporting consistent results across shifts. Robust construction for everyday workshop use Manufactured from special steel, the pin resists wear and maintains its dimensional integrity in standard workshop environments. The workshop version designation denotes a balance between precision finish and practical durability for everyday use; sharp edges and contact faces are produced to preserve measurement reliability while withstanding routine handling. For customers who require traceable verification, the pin can be incorporated into documented inspection routines, ensuring that component acceptance remains transparent and auditable. Contact Metav Werkzeuge for tailored advice on integrating the M323.085 into inspection jigs or for procurement from Emmerich; our specialists will confirm suitability for specific measurement tasks and delivery options. Technical data Article number: M323.085 GTIN: 4061905054044 Category: Gauge pins Type: Single test pin Special feature: Workshop version Facts Diameter (mm): 0.85 Length (mm): 50 Tolerance (mm): ±0.001 Weight (kg): 0.003 Features / Material Material: Special steel Supply: single item Intended use: dimensional verification and go/no‑go testing FAQ What is the primary application of this gauge pin? This gauge pin (M323.085) is intended for fine dimensional verification, internal alignment checks and end‑dimension control in workshop and production inspection. Does the M323.085 require special care during use? Regular cleaning and avoidance of impact will preserve the dimensional integrity of the pin; routine visual checks are recommended to confirm contact faces remain undamaged. Is the accuracy of ±0.001 mm sufficient for laboratory tasks? The ±0.001 mm tolerance positions the pin for high‑precision workshop and many laboratory applications where micrometric repeatability is required. Can the gauge pin be used in automated jigs? Yes, the single‑piece design and 50 mm length allow straightforward integration into manual and semi‑automated jigs for go/no‑go or depth checks. What material is the pin made from and why does that matter? The pin is produced from special steel, chosen to offer wear resistance and dimensional stability under normal workshop conditions. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
0.86mm Gauge Pin, Single, ±0.001mm Accuracy, 50mm Length, Workshop Finish - Metav IndustryLine
Benefit from a workshop-grade solution that combines micrometre-level tolerance (±0.001 mm) with a compact 0.86 mm diameter and a robust 50 mm length for consistent end-measurement checks; order the gauge pin directly via Metav Werkzeuge or ask our consultants if needed. Gauge pin M323.086 — single test pin, 0.86 mm diameter, ±0.001 mm tolerance (Metav IndustryLine) A gauge pin designed for precise dimensional verification in workshop and inspection routines, offering micrometre accuracy and a transport-friendly protective case Workshop version for regular use Diameter 0.86 mm with ±0.001 mm tolerance 50 mm length for repeatable end measurements Made from special steel for durability Repeatable small-diameter verification for production control This test pin delivers consistent dimensional checks where every micrometre matters. With a nominal diameter of 0.86 mm and a tolerance of ±0.001 mm (one micrometre), the component supports tight acceptance criteria in assembly and inspection. The compact form and low mass reduce the influence on fragile assemblies during verification, while the workshop-grade build ensures the pin withstands frequent handling. Clear numerical specifications simplify integration into quality plans and help maintain production flow with measurable repeatability. How micrometre accuracy improves process decisions A tolerance of ±0.001 mm converts directly into better process control: deviations are detected earlier and corrective actions can be taken before scrap increases. The pin is suitable for use as a reference in pin gauge stacks, for verifying bores and holes, and for checking end dimensions in small components — applications where high resolution measurement is required. Using this precision pin reduces uncertainty in go/no‑go assessments and supports traceable inspection routines that form the basis of reliable quality documentation. Durable handling, transport-safe delivery and workshop suitability Manufactured from special steel, the pin is optimised for daily inspection tasks; the workshop version balances wear resistance with practical handling. Delivery includes a protective case for safe transport and storage, ensuring the pin remains serviceable between uses. Its 50 mm length provides a firm reference for end‑measurements without excessive overhang, making it suitable for bench inspections and fixture-based checks. For serial inspection tasks, the compact dimensions and protective packaging simplify logistics and reduce downtime. For workshop-ready precision from Metav IndustryLine, contact Metav Werkzeuge for personalised advice and reliable supply from Emmerich — call +49 2822 7131930 or email info@metav-werkzeuge.com to secure the required gauge pin. Technical Data SKU: M323.086 GTIN: 4061905054051 Label: Prüfstift, einzeln, 0,86mm, +/- 0.001 mm Länge 50 mm Facts Diameter: 0.86 mm Tolerance: ±0.001 mm Length: 50 mm Weight: 0.003 kg Special features Material: Spezial-Stahl (special steel) Workshop version (Werkstatt-Ausführung) Delivered in protective case for transport FAQ What is the nominal diameter and tolerance of this gauge pin? The gauge pin has a nominal diameter of 0.86 mm with a specified tolerance of ±0.001 mm, suitable for micrometre-level checks. Can the pin be used for bore and end-measurements? Yes, the M323.086 single test pin is designed for bore verification and end-measurements in small components and fixture checks. Is the pin suitable for daily workshop use? The workshop version construction and the special steel material make this pin appropriate for regular inspection tasks; it is supplied in a protective case to aid transport and storage. Metav IndustryLine: Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
0.87mm Test Pin, Single, ±0.001mm Accuracy, Length 50mm, Workshop Version - Metav IndustryLine
Take advantage of extremely tight tolerances and compact dimensions for reliable end measurements in routine inspection and setup tasks. The combination of ±0.001 mm accuracy, a slender 0.87 mm diameter and a 50 mm usable length ensures reproducible fits and minimal measuring uncertainty. Order directly via Metav Werkzeuge or consult our specialists for selection support. Pin gauge M323.087 — 0.87 mm, ±0.001 mm, 50 mm, Metav IndustryLine A Pin gauge M323.087 designed as a workshop-grade inspection pin for precise end measurements, gauge setting and quality checks in production and maintenance environments Ø 0.87 mm precision pin Tolerance ±0.001 mm for accurate fits 50 mm length in workshop execution Special steel construction Precision that keeps parts within tolerance A slender inspection pin with a diameter of 0.87 mm and a declared ±0.001 mm tolerance is intended for tasks where microscopic deviations matter. The very fine tolerance reduces rework by providing a clear reference for fit or bore checks and supports reproducible measurements during assembly or calibration routines. The high dimensional stability of the special steel alloy ensures minimal thermal or wear-related drift, so reference checks remain dependable across repeated cycles. This level of precision suits quality control stations and setting processes where small clearances define product function. Built for everyday workshop inspection and handling The workshop-grade finish and a 50 mm usable length balance accessibility and stiffness: long enough to reach recessed features yet short enough to avoid bending under normal handling. The lightweight construction (approx. 0.003 kg) and compact form factor make the pin easy to handle during rapid inspection sequences or when fitting into gauge blocks and fixtures. Delivery in a protective transport box preserves the working surface and prevents damage between uses, which extends service life and maintains repeatability. Use as an end-measure, go/no-go plug, or in fixture alignment where repeatable contact geometry is required. Traceability and operational benefits for quality workflows Traceable identifiers such as the SKU and GTIN support inventory control and documentation in regulated environments; the robust design reduces downtime caused by uncertain reference tools. Integration into existing inspection routines is straightforward: the pin serves both as a precise reference and as a durable workshop tool, reducing the need for frequent replacements. Sourcing from Metav IndustryLine adds the reassurance of a European quality filter and logistics base in Emmerich, helping to keep measurements affordable and reliably supplied for industrial and craft applications. For a production or calibration setup that demands micrometre-level certainty, contact Metav Werkzeuge to discuss the M323.087 pin gauge and ensure the correct reference tools are selected for the intended inspection task Technical data Article number: M323.087 GTIN: 4061905054068 Category: Pin gauges / Messstifte Brand: Metav IndustryLine ECLASS: 21170231 Numerical data Diameter: 0.87 mm Tolerance / Accuracy: ±0.001 mm Length: 50 mm Weight: 0.003 kg Special features Material: Special steel Workshop execution Delivery in protective transport box Label: Prüfstift, einzeln, 0,87mm, +/- 0.001 mm Länge 50 mm FAQ What measurement tasks is this pin gauge suitable for? The pin gauge M323.087 is intended for end measurements, fit checks and fixture set-up where a 0.87 mm reference with ±0.001 mm accuracy is required. Is the surface material resistant to workshop wear? Yes, the pin gauge is manufactured from special steel, offering good wear resistance for routine inspection tasks in a workshop environment. Can this pin be used for bore gauging or plug-testing? The slender diameter and tight tolerance make the M323.087 suitable as a go/no-go or reference plug for small bores and precision fixture checks. How should the pin be stored between uses? Store the pin in its protective transport box to avoid nicks or contamination of the contact surface and to maintain measurement reliability. Does the product include traceability identifiers for inventory management? Yes, the SKU M323.087 and GTIN 4061905054068 facilitate traceability and inventory control in quality systems. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
0.88mm Gauge Pin Length 50mm ±0.001mm Workshop Finish, Packed Case - Metav IndustryLine
A compact workshop test pin that combines a 0.88 mm nominal diameter with a confirmed ±0.001 mm tolerance and a sturdy 50 mm length gives reliable end‑measurement performance for inspection and assembly tasks; supplied in a protective transport case and made from special steel, it supports consistent quality control across production. Order via Metav Werkzeuge or consult the product specialists for application advice. Gauge pin, 0.88 mm, ±0.001 mm, 50 mm — Metav IndustryLine workshop version Gauge pin, 0.88 mm, ±0.001 mm, 50 mm is a precision end‑measurement pin designed for inspection, fit checks and small‑bore verification in workshop environments Workshop version for robust use Diameter 0.88 mm with tight tolerances Accuracy ±0.001 mm for end measurements Made from special steel, length 50 mm Precision that reduces rework and secures tolerances The gauge pin delivers an accuracy of ±0.001 mm, a level that narrows acceptance windows and reduces the need for repeat machining or manual rework. For small‑bore inspections and go/no‑go assessments, the 0.88 mm nominal diameter provides a consistent datum that is easy to incorporate into inspection jigs and gauges. The tight tolerance means measurement uncertainty is minimised, allowing process engineers to rely on these pins for routine quality checks and sample testing while maintaining production throughput. Built for everyday workshop handling The workshop execution and special steel construction ensure the pin withstands frequent use and handling typical of production floors. At a nominal length of 50 mm, the pin balances reach and rigidity: long enough for through‑hole verification, yet short enough to avoid undue bending or deflection during measurement. The small overall mass supports quick changeover and reduces operator fatigue when multiple pins are handled. Supplied in a protective transport case, the item arrives ready for safe storage and on‑bench use. Practical integration into inspection workflows Designed as a simple, robust measurement tool, the pin slips easily into comparator fixtures, plug‑gauge stacks and manual inspection routines where precise end‑measurement references are required. Its compact form factor keeps it accessible in quality boxes and tool stations, while the combination of material choice and manufacture quality helps maintain a stable gauge over repeated cycles. For process documentation or inventory, the part is identified by its SKU and GTIN in technical records and stock lists, simplifying traceability within standard metrology procedures. For consistent, workshop‑ready precision choose the Metav IndustryLine gauge pin (SKU M323.088) — order through Metav Werkzeuge or request application guidance from our product advisors at Metav Werkzeuge GmbH Technical Data Article number: M323.088 GTIN: 4061905054136 Manufacturer: Metav IndustryLine Facts Diameter: 0.88 mm Length: 50 mm Accuracy: ±0.001 mm Weight: 0.003 kg Special features Workshop execution Material: special steel Protective transport case included Suitable for end measurements and fit checks FAQ What diameter and tolerance does the gauge pin have? The gauge pin has a nominal diameter of 0.88 mm and a manufacturing tolerance of ±0.001 mm. Which applications is the pin suitable for? This gauge pin is intended for end measurements, small‑bore verification, fit checks and integration into inspection jigs in workshop and light production environments. What material is used and how is it supplied? The pin is made from special steel and is supplied in a protective transport case suitable for workshop handling. How long is the pin and how does that affect use? The pin is 50 mm long, giving sufficient reach for many through‑hole and assembly checks while maintaining rigidity for reliable measurements. Is the pin traceable in stock and records? The item is identifiable by its SKU M323.088 and GTIN 4061905054136 for inventory and traceability purposes. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
0.89mm Gauge Pin Length 50mm ±0.001mm Workshop Finish - Metav IndustryLine
Take advantage of high repeatability and micrometre-level tolerance in a compact format: the slim probe guarantees reliable end‑dimension checks, minimal fixture disturbance and consistent pass/fail decisions. Order directly via Metav Werkzeuge or consult our technical advisors for application support. Test Pin M323.089 — Precision probe 0.89 mm, ±0.001 mm A Test Pin M323.089 for fine end‑measurement and fixture verification in workshop and metrology environments, designed as a robust workshop version for frequent use. High precision ±0.001 mm tolerance Diameter 0.89 mm for fine probing 50 mm overall length, slim profile Special steel for wear resistance Precision where micrometres matter The probe delivers ±0.001 mm accuracy, equivalent to 1 µm, which makes it suitable for tasks that require micron‑level certainty such as end‑dimension verification and small‑bore inspection. Manufactured in a workshop version, the probe balances durability with a slim geometry that reduces contact disturbance during measuring. The small 0.89 mm diameter allows access to tight features while the 50 mm length provides sufficient reach without compromising stiffness. This combination supports faster decision cycles on the shop floor and reduces the likelihood of rework through clearer pass/fail results. Robust design for repetitive workshop use Constructed from special steel, the probe is intended for continuous handling and repeated contact with gauging fixtures. The material choice improves wear resistance and maintains tip form over many cycles, preserving the original measurement behaviour. As a single probe with a precise ±0.001 mm specification, it fits into fixture arrays, test benches and bespoke locating tools where consistent contact geometry is essential. The lightweight nature (approx. 0.003 kg) makes integration into automated or semi‑automated holders straightforward and minimises additional inertia on delicate positioning stages. Practical benefits for quality assurance workflows Using a fine probe like this reduces measurement uncertainty at critical control points and supports traceable inspection routines. The slim probe aids in checking end faces, small bores and precision features without the need for larger, more invasive instruments. Its repeatable contact geometry helps standardise measurement routines across operators and shifts, improving statistical process control figures and supporting quicker root‑cause analysis when deviations occur. For organisations looking to centralise metrology supply chain decisions, the probe is a compact, reliable component that complements gauges and inspection fixtures. For application advice or to secure supply from Metav Werkzeuge, contact our technical team and specify the M323.089 for tailored recommendations and rapid delivery. Technical data Article number: M323.089 GTIN: 4061905054938 Manufacturer: Metav IndustryLine Facts Diameter: 0.89 mm Length: 50 mm Tolerance/accuracy: ±0.001 mm Weight: 0.003 kg Special features Material: Special steel Version: Workshop execution Intended use: End‑dimension checks and fixture probing FAQ What tolerances can be expected when using this test pin? The test pin M323.089 from Metav IndustryLine is specified with a tolerance of ±0.001 mm, providing micrometre‑level repeatability for precise end‑measurement tasks. Is the probe suitable for integration into existing fixture plates? Yes, the probe’s 0.89 mm diameter and 50 mm length make it compatible with common fixture arrays and test bench holders where fine probing is required. What material is the pin made from and how does that affect wear? The probe is made of special steel, chosen to improve wear resistance and preserve tip geometry under frequent contact, supporting long service life in workshop conditions. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
0.8mm Gauge Pin 50mm Length, ±0.001 mm Workshop Version - Metav IndustryLine
Take advantage of the combination of ultra‑fine accuracy, compact micro sizing and robust workshop design to ensure reproducible end‑measurements; order the Test pin directly via Metav Werkzeuge or contact our consultants for application advice. Test pin M323.080 — measuring pin, 0.80 mm diameter, ±0.001 mm accuracy (Metav IndustryLine) The Test pin M323.080 is a workshop‑grade measuring pin designed for precise end‑measurements and gauging tasks in finely machined components. Diameter 0.80 mm for tight fits Tolerance ±0.001 mm for micrometre accuracy Length 50 mm in workshop execution Made from special steel for durability Micrometre‑level repeatability for fine parts The compact measuring pin delivers a ±0.001 mm tolerance, equivalent to one micrometre, which makes it suitable where minimal deviation is critical. With a shaft diameter of 0.80 mm, the pin is optimised for tight bores, pin gauges and verification of end‑dimensions. The very small diameter combined with the high accuracy reduces measurement uncertainty when used in calibrated fixtures or gauge blocks, supporting traceable inspection steps in workshop and quality environments. Robust workshop construction that endures routine use Constructed from special steel in a workshop execution, the design balances hardness with surface finish to resist wear during repeated seating operations. The 50 mm active length provides enough engagement for stable measurements while remaining easy to handle and position. Low mass and stable geometry ensure consistent contact behaviour, which helps to maintain reproducibility in serial checks and during comparative gauging tasks. Compact handling and safe transport for frequent use Classified as a micro‑class measuring instrument (max. range 10–100 mm), the pin suits delicate assembly, watchmaking and small‑part inspection where space is limited. Supplied in a protective transport case, the unit is easy to store and move between workstations without risk of accidental damage. As a single‑piece measuring element, it integrates simply into existing fixtures, calliper adaptors or dedicated gauge holders to support fast, reliable end‑measurements. Request supply and technical advice from Metav Werkzeuge for this Metav IndustryLine measuring pin M323.080 — contact info@metav-werkzeuge.com or call +49 2822 7131930 for immediate assistance Technical data SKU: M323.080 GTIN: 4061905056994 Brand: Metav IndustryLine Dimensions & accuracy Diameter: 0.80 mm Length: 50 mm Tolerance / Accuracy: ±0.001 mm Weight: 0.003 kg Special features Material: Special steel Workshop execution (Werkstatt‑Ausführung) Supplied in transport case Intended use: end‑measurements / gauge applications FAQ What level of accuracy does this measuring pin offer? The Test pin M323.080 offers an accuracy of ±0.001 mm, providing micrometre‑level precision suitable for fine gauging and end‑measurement tasks. Is the measuring pin suitable for tiny bore gauges and watch components? Yes, the 0.80 mm diameter and micro‑class sizing make the pin well suited to small bores, watch parts and other compact assemblies. What material is the pin made from and why does that matter? The pin is made from special steel; this provides a durable contact surface and consistent geometry, which supports repeatable measurements in workshop conditions. How is the pin delivered to ensure safe handling? The measuring pin is supplied in a protective transport case to prevent damage during storage and transfer between workstations. Can the measuring pin be used with standard gauge holders and fixtures? The measuring pin is designed for integration with common fixtures and gauge adaptors used for end‑measurements and comparative checks in production and inspection setups. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
0.91mm Gauge Pin Length 50 mm ±0.001mm Workshop Finish - Metav IndustryLine
Compact, micrometric control meets robust workshop use: with a 0.91 mm diameter and ±0.001 mm tolerance, this single test pin delivers repeatable end‑measurements and dependable setting work. Order directly via Metav Werkzeuge or consult our specialists for application support. M323.091 Gauge pin — 0.91 mm diameter, ±0.001 mm tolerance (Metav IndustryLine) The M323.091 is a precision gauge pin for end‑measurement, setting and inspection tasks in workshop and production environments, supplied as a single hardened test pin for stable seating and repeatable checks. Diameter 0.91 mm with ±0.001 mm accuracy Length 50 mm for stable engagement Made from special steel for durability Workshop version for everyday use Achieve micron-level certainty in end measurements A compact measuring element with a nominal diameter of 0.91 mm, the test pin offers a tolerance of ±0.001 mm (1 µm), enabling high‑precision end measurements and calibration tasks where tight clearances matter. The fine tolerance reduces measurement variation and increases confidence when checking small bores, end stops or reference surfaces. In practice, the narrow diameter combined with such tight deviation permits consistent repeatability, lowering the risk of false rejections and streamlining inspection workflows. Robust construction for repeated workshop use Manufactured from special steel, the pin balances wear resistance with dimensional stability so that routine handling and repeated seating do not compromise form or function. The 50 mm overall length provides sufficient contact depth for secure engagement in fixtures and gauges while remaining convenient for manual handling or insertion into measurement setups. As a single‑piece test pin in a workshop specification, it is optimised for day‑to‑day use where reliability and longevity cut down on downtime and spare‑part turnover. Practical benefits for quality assurance and process setup Using this pin as a reference or setting gauge simplifies alignment and fixturing tasks and shortens setup time on production equipment. The compact format makes it suitable for close‑tolerance assemblies and micro‑components where space is restricted but accuracy is non‑negotiable. Supplied under the Metav IndustryLine label, the product aligns with a broader promise of accessible precision: consistent parts, traceable identification and dependable sourcing from a European quality filter. Choose the Metav IndustryLine M323.091 for micron‑accurate end measurements and contact Metav Werkzeuge for tailored advice or ordering at info@metav-werkzeuge.com or by phone on +49 2822 7131930 Technical data Article number: M323.091 GTIN: 4061905054952 Manufacturer: Metav IndustryLine Facts Diameter: 0.91 mm Tolerance: ±0.001 mm Length: 50 mm Weight: 0.003 kg Special features Material: special steel Single test pin Workshop version Story trigger: end measurements FAQ What is the measurement tolerance of this gauge pin? The M323.091 gauge pin is specified to ±0.001 mm, making it suitable for micrometric end‑measurements and precision setting tasks. Can this pin be used for bore checking and fixture alignment? Yes. The single‑piece design and 50 mm length allow secure engagement for bore checks, fixture setting and reference positioning in inspection operations. What material is the pin made from and how does that affect durability? The pin is made from special steel, chosen for a balance of hardness and wear resistance so that dimensional stability is maintained during repeated use. Is the M323.091 traceable for quality documentation? The product carries a GTIN (4061905054952) and is supplied under the Metav IndustryLine portfolio for consistent sourcing and traceability in production records. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
0.92mm Gauge Pin Length 50mm ±0.001mm Workshop Finish - Metav IndustryLine
Take advantage of ±0.001 mm tolerance together with a slim 0.92 mm diameter and a 50 mm working length for reliable end‑measure checks; the workshop-grade construction and special steel ensure repeatable results. Order the gauge pin directly via Metav Werkzeuge or consult the Metav specialists for application advice. Gauge pin M323.092 — 0.92 mm diameter, ±0.001 mm accuracy (Metav IndustryLine) The gauge pin M323.092 is a single, workshop-grade test pin for precise end‑measure verification and small‑feature gauging in inspection and assembly operations ±0.001 mm tolerance for high-precision checks 0.92 mm diameter for fine-feature measurement 50 mm hardened special steel length Workshop execution for robust daily use Consistent end-measure accuracy for quality control The slim measuring shaft is manufactured for end‑measure tasks where repeatability is essential. With a stated tolerance of ±0.001 mm, the pin supports fine inspection steps such as plug‑gauge cross checks and go/no‑go verification of small bores or features. The tight tolerance reduces measurement uncertainty and shortens corrective loops in production control, helping to maintain a stable process capability without extensive adjustment or compensating procedures. Robust construction to withstand workshop routines A special steel composition and a 50 mm working length combine to provide wear resistance and dimensional stability during frequent handling. The workshop execution design prioritises practical robustness while keeping the probe slender enough for confined features. The compact mass and balanced form enable steady contact in manual gauging setups and contribute to long service life under typical machining‑shop conditions. Practical integration and traceability in inspection workflows The pin is supplied as a single test item with a clear article reference for inventory and traceability. The compact geometry suits end‑measure checks, bench inspection jigs and small‑feature verification tasks. Identification by SKU and GTIN simplifies stock management and order replenishment, allowing seamless integration into existing quality routines and parts lists. For precision end‑measure verification, trust the Metav IndustryLine quality — contact Metav Werkzeuge for procurement and technical guidance via info@metav-werkzeuge.com or +49 2822 7131930 Technical data Article number: M323.092 GTIN: 4061905054969 Eclass: 21170231 Brand: Metav IndustryLine Category: Gauge pins Facts Diameter: 0.92 mm Length: 50 mm Tolerance: ±0.001 mm Weight: 0.003 kg Special features Material: Special steel Workshop execution Supplied as a single test pin Intended for end‑measure checks FAQ What applications suit this gauge pin? The gauge pin M323.092 is intended for end‑measure verification and small‑feature gauging in inspection, assembly and bench inspection workflows. Is the diameter and tolerance suitable for fine bores? Yes. The 0.92 mm diameter combined with a ±0.001 mm tolerance makes the M323.092 suitable for precise checks of fine bores and small mechanical features. What material is used for the pin? The shaft is made from special steel, providing wear resistance and dimensional stability for routine workshop use. How is the item identified for ordering and stock control? Order and identify the part by Article number M323.092 or GTIN 4061905054969 for reliable procurement and inventory management. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
Fast, tactile checks where electronics are impractical
Gauges and test pins provide unequivocal go/no-go results for threads, bores, gaps and radii without relying on electronics. The range covers plug gauges and ring gauges for internal and external threads, feeler gauges and precision feeler strips for micro‑gap assessment, plus probe pins and measuring pins for tactile diameter and pitch checks.
How these tools work in the production environment
Mechanical gauges operate as direct reference standards: a plug gauge or ring gauge verifies conformity to thread profiles and mating ability, while limit gauges separate accept from reject in a single step. Test pins are used to tactilely measure small bore diameters, centre‑to‑centre distances and radii. Manufactured from hardened gauge steel or ceramic and often precision lapped, these instruments deliver immediate physical results that are ideal for incoming inspection, machine‑side checks and final control.
Measurable benefits that affect production performance
- Reduced scrap and rework through rapid, unambiguous pass/fail assessment.
- Increased repeatability thanks to very low measurement uncertainty and fine lapping.
- Lower downtime: quick checks at the machine save cycle time and reduce setup periods.
- Durable construction with high wear resistance from specialised, low‑distortion alloys.
- Versatile delivery formats: individual gauges, organised sets in wooden cases or metre‑length feeler rolls compliant with DIN 2269.
Why Metav is the practical choice for precision supplies
Metav combines decades of expertise with a broad warehouse and quality filtering from Emmerich. As a precision partner for industry, craft and trade, Metav supplies a comprehensive selection of gauges and test pins alongside complementary tools such as precision calipers and setting rings. With over 48,000 customers and a catalogue exceeding 250,000 items, Metav is positioned to supply reliably, reduce vendor complexity and support traceable quality control to national standards.
Summary
Gauges and test pins are indispensable for dependable, repeatable quality assurance where tactile, mechanical verification is preferred. Choose these plug gauges, ring gauges, feeler strips and probe pins when immediate, robust measurement decisions are required on the shop floor.
FAQ
What materials are gauges and test pins typically made from?
Gauges and test pins are usually manufactured from hardened gauge steel for durability and wear resistance; ceramic variants are available where thermal stability and minimal wear are critical.
How do thread gauges ensure mating capability?
Thread plug gauges and ring gauges check flank diameters and thread form against standards, providing a clear go/no‑go verdict that confirms pairability with mating parts.
Which tolerance class should I choose for probe pins and gauge sets?
Select tolerance classes aligned with your inspection requirements; for high‑precision tasks, sets produced to DIN 2269 or equivalent tolerance classes ensure micrometre‑level control and repeatability.
Can feeler gauges measure contact gaps in valve and engine work reliably?
Yes. Feeler gauges and precision feeler strips, supplied either as a fan or metre‑length rolls, allow accurate assessment of valve clearances and contact gaps down to micrometre increments.
How do limit gauges speed up in‑process inspection?
Limit gauges separate good from bad in a single, tactile operation, enabling rapid go/no‑go checks at the machine and reducing both inspection time and the likelihood of human interpretation errors.
Fragen zu diesen Produkten??
Mit mehr als 30 Jahren Erfahrung beraten wir Sie gerne persönlich.
Tel.: +49 2822 7131930
Mail: info@metav-werkzeuge.com