Precision gauge blocks and plug gauges for reliable dimensional control
Mechanical gauge blocks and plug gauges are essential for tactile verification of threads, bores and gap dimensions, providing fast, unambiguous go/no-go results that enhance process reliability and reduce scrap. Designed for industrial metalworking and toolmaking, these precision tools support incoming inspection and final quality checks by delivering traceable measurements in applications such as thread inspection, bore diameter testing and spacing checks. Manufactured from specially hardened, low-distortion alloys and fine-lapped for minimal measurement uncertainty, the range includes thread plug gauges, precision plug gauges and calibration gauge blocks to ensure long-term repeatability and wear resistance.
0.93mm Gauge Pin Length 50mm ±0.001mm Workshop Finish, Special Steel - Metav IndustryLine
Take advantage of the 0.93 mm diameter and ±0.001 mm tolerance for reliable end‑dimension checks; the compact 50 mm length and workshop‑grade construction ensure fast, repeatable inspection at the bench. Order the gauge pin directly via Metav Werkzeuge or contact their consultants for technical advice. Gauge pin M323.093 — single gauge pin, 0.93 mm diameter, ±0.001 mm tolerance The gauge pin M323.093 is a single‑piece checking pin intended for high‑precision bore and end‑dimension inspection in workshop and small‑parts metrology. Workshop-grade design Diameter 0.93 mm Tolerance ±0.001 mm Length 50 mm Engineered for repeatable end‑dimension checks The small nominal diameter of 0.93 mm combined with a tolerance of ±0.001 mm provides high‑precision verification where tight fits and fine bores are involved. In practical terms, this means a single insertion offers an immediate assessment of bore conformity and end dimensions without complex set‑ups. The tight tolerance supports comparative and go/no‑go assessment routines commonly used in quality control, helping to pinpoint deviations early in the production chain and reducing rework. Practical design for workshop inspection Manufactured in special steel and finished for workshop use, the pin’s 50 mm length gives sufficient reach for short bores and end measurements while remaining easy to handle. The compact form suits bench inspection and manual gauging tasks where rapid, repeatable checks are required. The workshop‑grade execution balances robustness with the fine surface finish needed to avoid false readings caused by damage or contamination. Integration into inspection workflows As a single gauge pin, the M323.093 is suitable for inclusion in plug gauge sets, fixture checks and small‑part inspection jigs. The item’s compact dimensions make it compatible with precision holders and comparator fixtures used in metrology departments. Used correctly, the pin contributes to repeatable measurements that support process control, statistical sampling and routine acceptance testing in toolmaking and precision engineering. Handling and maintenance for consistent results To preserve accuracy, the pin should be cleaned of debris and light oils prior to use and handled with care to avoid nicks or dents; simple protective storage after inspection will prolong service life. Regular visual checks are sufficient for everyday use; for formal traceability or certification, request calibration options from Metav Werkzeuge. Proper handling ensures consistent results and reduces the risk of measurement uncertainty in successive checks. Request a technical consultation or quotation from Metav Werkzeuge to integrate the M323.093 gauge pin into inspection protocols and ensure optimal application in the workshop Technical Data Article number: M323.093 GTIN: 4061905054976 ECLASS: 21170231 Facts Diameter: 0.93 mm Tolerance: ±0.001 mm Length: 50 mm Weight: 0.003 kg Special features Material: special steel Workshop execution Single gauge pin Label: Prüfstift, single, 0.93 mm FAQ What applications suit this gauge pin? This gauge pin is intended for precise bore checks and end‑dimension inspection in toolmaking, small‑parts metrology and workshop quality control; the M323.093 is optimised for fine bores. Is the material corrosion resistant? The pin is made from special steel with a workshop finish; corrosion resistance depends on the alloy and local conditions—recommended to dry and lightly oil after use if required. Can the pin be used in a comparator fixture? Yes—the compact dimensions and consistent tolerance make the pin suitable for comparator fixtures, plug gauge sets and bespoke inspection jigs. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
0.94mm Gauge Pin Length 50mm ±0.001mm Workshop Version, Special Steel - Metav IndustryLine
Take advantage of workshop-grade accuracy and compact design for consistent end‑measure checks: the pin's 0.94 mm diameter with ±0.001 mm tolerance and 50 mm length ensures repeatable positioning and tight fit inspections. Order the gauge pin directly via Metav Werkzeuge or consult our advisors for specification matching. Gauge pin M323.094 — 0.94 mm diameter, ±0.001 mm, 50 mm length The gauge pin M323.094 is a single, workshop‑grade precision plug gauge for end‑dimension verification and fixture alignment in machine shops and quality control benches Workshop‑grade precision pin Diameter 0.94 mm with ±0.001 mm tolerance Compact 50 mm length for fixture checks Made from special steel for wear resistance Consistent, measurable accuracy for production control A core benefit of this precision pin is its extremely tight tolerance: ±0.001 mm. That level of repeatability converts directly into fewer false rejects and more reliable go/no‑go decisions on the shop floor. The slim 0.94 mm diameter is ideal for verifying small bores, end‑faces and plug gauges; by using a controlled plug rather than approximate gauging, process capability and traceability are improved. The numeric tolerance stated is an objective specification that supports statistical process control and helps reduce downstream rework. Practical design that suits workshop handling and fixtures Engineered as a workshop‑grade component, the pin combines a hardened surface with a compact 50 mm shank to fit in tight jigs and alignment tools. Its small mass (approx. 0.003 kg) and straight geometry make it easy to handle while retaining sufficient stiffness for repeatable measurements. The special steel construction increases wear resistance in frequent use, extending service life under normal production conditions. The simple single‑pin format also allows integration into bespoke fixture sets or replacement of worn elements without overhaul of tooling. Clear specifications to streamline quality routines Specifications are presented as direct, verifiable data to support purchasing and inspection planning: nominal diameter, measured tolerance and length are defined, enabling immediate comparison with inspection requirements. The compact format suits use as an end‑dimension master, plug check or positional reference in assembly processes. For customers seeking integration into measurement documentation, the SKU and GTIN are provided in the technical details below to simplify inventory and traceability. For precision that matches workshop realities, contact Metav Werkzeuge in Emmerich for ordering and technical matching of the Metav IndustryLine range; advisors can clarify compatibility with existing gauges and fixtures Technical data Article number: M323.094 GTIN: 4061905054983 Manufacturer: Metav IndustryLine Facts Diameter: 0.94 mm Length: 50 mm Accuracy: ±0.001 mm Weight: 0.003 kg Special features Workshop‑grade execution Material: special steel Single gauge pin Category: gauge pins SKU: M323.094 FAQ What tolerance does the pin offer? The pin provides a tolerance of ±0.001 mm, ensuring very tight repeatability for end‑measure checks with the gauge pin M323.094 from Metav IndustryLine. For which applications is this pin suited? It is suited to small‑bore verification, end‑dimension masters, fixture alignment and plug gauge checks where a 0.94 mm reference is required. Is the pin suitable for frequent workshop use? Yes. The special steel construction and workshop‑grade design make the pin appropriate for regular use in production and quality control settings. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
0.95mm Test Pin Length 50mm ±0.001mm Workshop Version - Metav IndustryLine
Take advantage of the combination of high repeatability, tight tolerance and a robust workshop design to secure reliable end‑measure checks. The compact 50 mm length and 0.95 mm diameter provide efficient access into small bores and gauges; order directly via Metav Werkzeuge or consult the team for application advice. Gauge pin M323.095 — precision test pin, 0.95 mm, ±0.001 mm (Metav IndustryLine) A gauge pin M323.095 designed for accurate end‑measure verification and alignment checks in workshop metrology, supplied as a single precision pin for component inspection and fixture testing Diameter 0.95 mm, workshop version Tolerance ±0.001 mm for reliable checking Length 50 mm for small‑part access Special steel construction for durability Consistent fit control with micrometric accuracy The small‑diameter gauge pin is engineered to deliver ±0.001 mm repeatability, which reduces ambiguity when verifying mating bores or end dimensions. The narrow 0.95 mm shaft allows entry into compact features where standard pins cannot reach, while the moderate 50 mm length ensures stable support during insertion. This combination translates into dependable go/no‑go assessments and fewer rework cycles in precision assembly. Robust workshop design for frequent use Constructed from special steel, the pin withstands routine handling and resists distortion under normal workshop conditions. The workshop version means the geometry and surface treatment are optimised for repeated manual use, maintaining measurement integrity over many cycles. That durability supports predictable inspection intervals and lowers total cost of ownership for quality control equipment. Easy integration into inspection jigs and fixtures The compact geometry and standardised sizing make the pin straightforward to incorporate into check fixtures and manual gauges. Its nominal diameter and tight tolerance provide a clear reference for alignment tasks, enabling quick visual or tactile pass/fail judgements during setup. The small mass also minimises inertial effects when inserting multiple pins in sequence, improving throughput in batch inspection. Practical benefits for small‑part measurement workflows Use of this precision pin reduces setup uncertainty for small components, supporting faster decision making on the shop floor. The single‑piece supply suits selective replacement strategies—keeping spares at hand avoids production pauses. In short, the tool is a focused solution for end‑measure verification where fine resolution and compact form are necessary. Contact Metav Werkzeuge today for application guidance and fast delivery from Emmerich — request the M323.095 precision gauge pin for reliable small‑part checks Technical Data Article number: M323.095 GTIN: 4061905054990 Label: Prüfstift, einzeln, 0,95mm, +/- 0.001 mm Länge 50 mm Facts Diameter: 0.95 mm Length: 50 mm Tolerance: ±0.001 mm Weight: 0.003 kg Special features Material: Special steel Workshop version Single delivery Accuracy class: ±0.001 mm FAQ What inspection tasks is this gauge pin suited for? This gauge pin is intended for end‑measure verification, alignment checks and entry into narrow bores where a 0.95 mm reference is required; it is particularly useful in precision assembly and fixture testing. Is the tolerance of ±0.001 mm sufficient for tool setting and gauge blocks? Yes, the ±0.001 mm tolerance of the M323.095 offers micrometric control suitable for high‑precision fit checks and many tool‑setting applications where fine resolution is needed. What material is the pin made from and how does that affect wear? The pin is manufactured from special steel, chosen to balance hardness and toughness for prolonged workshop use; this enhances wear resistance during repetitive insertion tasks. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
0.96mm Gauge Pin Length 50mm ±0.001mm Workshop Version - Metav IndustryLine
High‑precision workshop gauge offers repeatable end‑measure checks thanks to a tolerance of ±0.001 mm and a compact Ø 0.96 mm profile; the 50 mm length provides reliable access to recessed features. Order directly via Metav Werkzeuge or request application advice from the technical consultants for tailored guidance. Test pin M323.096 — workshop test pin, Ø 0.96 mm, ±0.001 mm accuracy (Metav IndustryLine) Test pin M323.096 is a workshop‑grade precision gauge pin designed for repeatable end‑measure checks and fixture verification in production and inspection environments Workshop-grade precision pin Ø 0.96 mm ±0.001 mm 50 mm length for recessed or end‑measure checks Manufactured from special steel for wear resistance Single-piece gauge for fixture and inspection use Engineered for consistent, high-precision measurements The M323.096 test pin is manufactured to deliver high‑precision results with a guaranteed tolerance of ±0.001 mm, making it suitable for end‑measure and plug‑gauge tasks where micrometre‑level repeatability is required. The small Ø 0.96 mm diameter reduces the influence of surface irregularities and allows measurement of narrow bores or fine features. Precision production and careful material selection reduce runout and ensure that every contact point behaves predictably, which improves statistical process control and reduces downstream rework. Fits into inspection jigs and gauges with minimal adaptation At a 50 mm active length and in a single‑piece configuration, this gauge pin integrates easily into existing fixtures, plug gauges and comparison rigs. The compact form factor supports tight pitch layouts on fixture plates and enables probing of recessed seats without additional extensions. Using a dedicated gauge pin rather than improvised probes simplifies setup validation and improves throughput because measurement steps remain short and reproducible, supporting faster cycle times in routine quality checks. Workshop durability and practical traceability for production use Constructed from special steel, the pin combines wear resistance with stable dimensional behaviour under normal workshop conditions. The workshop‑grade execution balances toughness and surface finish so that contact wear is predictable across batches of parts. Metav’s offering emphasises reliable supply and industry experience, rooted in a pragmatic approach to precision: broad product availability and a quality‑focused distribution centre in Emmerich help maintain continuity in production environments. For application clarification, the technical consultants at Metav Werkzeuge provide specification support and integration advice. Contact Metav Werkzeuge for technical guidance and to request the M323.096 test pin for precision end‑measure inspections Technical data Article number: M323.096 GTIN: 4061905055003 Brand: Metav IndustryLine Material: Spezial‑Stahl Length: 50 mm Facts Diameter: 0.96 mm Tolerance: ±0.001 mm Weight: 0.003 kg SKU: M323.096 Special features Workshop‑grade design Single test pin Suitable for end‑measure checks Compact profile for narrow bores FAQ What tolerance is offered on the test pin? The test pin is manufactured with a tolerance of ±0.001 mm, providing micrometre‑level repeatability suitable for precision end‑measure applications. Is the M323.096 pin suitable for recessed or hard‑to‑reach features? Yes. With a 50 mm active length and a compact Ø 0.96 mm profile, the pin is intended for recessed seats and narrow features in inspection fixtures. What material is the gauge pin made from? The gauge pin is produced from special steel, chosen for wear resistance and dimensional stability under normal workshop conditions. Is the pin supplied as an individual item or as part of a set? This item is supplied as a single test pin; the designation indicates an individual gauge component for fixture or inspection use. Can the pin be used in production gauges and jigs? The single‑piece configuration and workshop design make the pin suitable for incorporation into production jigs, plug gauges and test fixtures where repeatable contact geometry is required. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
0.97mm Test Pin Length 50mm, ±0.001mm, Workshop Version - Metav IndustryLine
Take advantage of the combination of industrial robustness, ±0.001 mm precision and compact handling for reliable end‑measurement tasks; the pin is supplied in a protective transport box ready for workshop use. Order the test pin directly via Metav Werkzeuge or ask our consultants if needed. Test pin M323.097 – Single precision gauge pin, Ø 0.97 mm, ±0.001 mm, 50 mm length (Metav IndustryLine) A Test pin M323.097 designed for precision end‑measurements and fixture checks in workshop and quality‑control environments. Precision tolerance ±0.001 mm Diameter 0.97 mm for fine measurements 50 mm length for secure probing Workshop version in protective transport box Reliability that reduces rework and inspection uncertainty With a declared tolerance of ±0.001 mm, this gauge pin meets the demands of tight inspection tolerances where repeatability matters. The small diameter of 0.97 mm is tailored for fine end‑measurements, plug gauges and feeler applications where minimal play and stable contact are required. Specifying such a narrow error band significantly reduces uncertainty in Go/No‑Go checks and stack‑up verifications, which in turn lowers the risk of costly rework further down the production chain. The numerical precision of the pin converts directly into measurable process benefits: fewer rejects, faster decisions at the inspection station and consistent reference points for routine quality control. Built for everyday workshop handling and secure storage Manufactured in special steel, the pin is a workshop version intended to withstand frequent handling and to resist local wear on the contact tip. The 50 mm shank length provides good engagement in probe holders and receptacles while remaining easy to manoeuvre by hand or with light tooling. Supplied in a protective transport box, the pin arrives ready for safe storage and transit; the packaging keeps the contact geometry intact during movement between bench, fixture or transport. The low individual mass of 0.003 kg makes the pin negligible in terms of added inertia in test fixtures, but the material choice preserves surface quality for longer service intervals. Simple integration into inspection and assembly workflows Traceable identifiers such as the SKU and GTIN enable straightforward documentation in inventory and inspection records; the compact form factor suits fixture assemblies and end‑of‑line verification points alike. The pin performs well as a reference element for small‑bore checks, alignment gauges and dimensional spot checks where high local accuracy is required. For automated measurement cells, the pin’s repeatable geometry supports consistent contact conditions; for manual inspections it supplies a reliable datum for comparative testing. Documentation and compatibility details can be matched to existing fixtures to ensure the pin integrates without modification. For consistent end‑measurement performance order the Metav IndustryLine Test pin M323.097 via Metav Werkzeuge in Emmerich or contact our specialists for specification advice and delivery options. Technical data SKU: M323.097 GTIN: 4061905055010 eClass: 21170231 Diameter: 0.97 mm Length: 50 mm Tolerance: ±0.001 mm Weight: 0.003 kg Material: special steel Workshop execution Supplied in protective transport box Category: Gauge pins FAQ What is the exact diameter and tolerance of the pin? The Test pin M323.097 has a diameter of 0.97 mm and a tolerance of ±0.001 mm. Which material is used for this gauge pin? The Test pin M323.097 is manufactured from special steel for improved wear resistance in workshop use. Is the pin suitable for use in small‑bore inspection fixtures? Yes, the M323.097 single gauge pin is designed for fine end‑measurements and fits small‑bore fixtures and probe holders. How is the pin delivered and protected during transport? Delivery includes a protective transport box to keep the contact geometry secure during transit and storage. Can the pin be used as a reference in comparative Go/No‑Go checks? The M323.097’s precision tolerance and stable geometry make it suitable as a reference element in comparative checks and inspection routines. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
0.98mm Gauge Pin, Single, ±0.001mm Accuracy, 50mm Length, Workshop Finish - Metav IndustryLine
Take advantage of the combination of pinpoint accuracy, robust workshop design and compact handling for reliable inspection routines; ideal for repeatable end‑measurements and fixture checks. Order the test pin directly via Metav Werkzeuge or consult the Metav team for technical guidance. Test pin M323.098 — precision gauge pin, 0.98 mm diameter, ±0.001 mm tolerance Test pin M323.098 offering a compact, workshop-ready solution for fine gauging and end-measurement tasks across inspection benches and assembly jigs High precision ±0.001 mm tolerance Diameter 0.98 mm for fine gauging 50 mm length for accurate depth checks Repeatable precision where micrometres are impractical This inspection mandrel delivers high precision in a compact format: a nominal diameter of 0.98 mm with a guaranteed tolerance of ±0.001 mm. Such tolerance places the component in the category of precision gauge pins used for dimensional verification of small bores and fit checks where sub‑millimetre accuracy is essential. Constructed from special steel, the pin offers consistent thermal and mechanical behaviour during short measurement cycles, supporting repeatable results on bench comparators and manual gauging fixtures. The specification supports clear decision‑making in quality control and reduces rework caused by ambiguous fit results. Practical design for workshop and inspection use The pin’s 50 mm length provides access into recesses and through-holes while remaining easy to handle on the shop floor; its lightweight character (approx. 0.003 kg) minimises operator fatigue during repetitive checks. The workshop version finish prioritises durability for everyday use and straightforward cleaning between shifts. Supplied as a single item, the component integrates seamlessly into existing go/no‑go sets, plug gauge nests or bespoke checking rigs; marked identification (SKU M323.098) and the included GTIN 4061905055027 simplify inventory and traceability workflows. Integration into measurement routines and process control As a dedicated gauge element, the pin is suitable for end‑measurements, reference checks and fixture validation where compact diameters are required. The stable geometry and narrow tolerance make the part well suited to comparative checks against master rings or as a reference when setting up micro‑drilling operations. The robust material choice and simple geometry reduce sources of error, supporting faster inspection throughput and clear conformity assessments. The component’s specification facilitates documentation in quality records and supports consistent process control across production batches. For workshop-ready precision from Metav IndustryLine, request the M323.098 test pin via Metav Werkzeuge to receive tailored technical advice and reliable supply from Emmerich: info@metav-werkzeuge.com, +49 2822 7131930 Technical data Article number: M323.098 GTIN: 4061905055027 SKU: M323.098 Facts Diameter: 0.98 mm Length: 50 mm Tolerance: ±0.001 mm Weight: 0.003 kg Special features Workshop version Material: special steel Single item delivery Application: end measurements / fit checking FAQ What tolerance can be expected from this gauge pin? The supplied test pin M323.098 is manufactured to a tolerance of ±0.001 mm, suitable for high‑precision gauging tasks and tight fit assessments. Which materials is the pin made from and how does that affect use? The pin is made of special steel, offering stable mechanical properties and wear resistance appropriate for regular inspection use in a workshop environment. Can the pin be used for bore verification and fixture alignment? Yes — the gauge pin’s 0.98 mm diameter and 50 mm length make it suitable for bore verification, end‑measurement checks and alignment tasks in small‑scale fixtures. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
0.99mm Test Pin, Single, ±0.001 mm Accuracy, 50mm Length, Workshop Version - Metav IndustryLine
Benefit from the combination of ±0.001 mm high accuracy, an ultra-slim 0.99 mm diameter and a robust workshop design for dependable end-measurements; order the gauge pin directly via Metav Werkzeuge or consult their specialists for application-specific advice. Gauge pin M323.099 – single 0.99 mm, ±0.001 mm accuracy (Metav IndustryLine) Gauge pin M323.099 is a precision measurement pin for end and fit checks in workshop environments, supplied as a single 50 mm length unit. 0.99 mm precision diameter, tolerance ±0.001 50 mm length for deep reach measurements Made from special steel for wear resistance Delivered in protective transport case Faster inspection through sub-micron repeatability The pin delivers ±0.001 mm tolerance, enabling highly consistent pass/fail checks and dimensional verification that reduce rework and inspection time. With a 0.99 mm diameter, the pin is suited to small-bore and fine-feature checks where conventional gauges struggle; the narrow profile minimises disturbance in tight fits and ensures repeatable seating. The precision tolerance is presented as an objective measurement parameter, supporting statistically sound quality control and permitting tighter control limits on production runs. Built for everyday workshop resilience Engineered as a workshop version, the pin is manufactured from special steel to resist wear under frequent use, preserving the gauge geometry and helping to maintain measurement integrity over time. The 50 mm length provides sufficient reach for many end-measurement tasks without compromising rigidity, and the single-piece supply simplifies inventory management. Delivered in a protective transport case, the pin arrives ready for secure storage and safe transport between inspection stations, reducing the risk of handling damage that would otherwise affect calibration intervals. Simple integration into quality processes As a dedicated gauge pin for end measurements, the component supports quick functional checks, go/no-go seating tests and comparative gauging routines on small diameters. The compact mass and nominal weight contribute negligible thermal inertia, which aids in maintaining dimensional stability during short measurement cycles. For traceability and logistics, the part is listed under SKU M323.099 and carries a GTIN for easy inventory control. Where specificity of fit is critical, this gauge pin offers a clear technical basis for decisions about assembly tolerances and inspection frequency. Contact Metav Werkzeuge today to discuss how the M323.099 gauge pin fits into current inspection workflows or to request tailored advice from the Metav specialists Technical Data Article number: M323.099 GTIN: 4061905055409 Brand: Metav IndustryLine Facts Diameter: 0.99 mm Length: 50 mm Tolerance / Accuracy: ±0.001 mm Weight: 0.003 kg Special features Workshop version Material: special steel Single piece delivery Protective transport case FAQ What tolerances does this gauge pin achieve? The gauge pin M323.099 achieves a tolerance of ±0.001 mm, suitable for fine end-measurement tasks and tight-fit checks. Is the pin suitable for repetitive use in a production workshop? Yes, the workshop version of the gauge pin is made from special steel and is supplied in a protective transport case to maintain geometry during regular handling. What length and diameter does this pin provide? This model is supplied as a single 50 mm length pin with a diameter of 0.99 mm, identified as M323.099 for stock and ordering. Can the pin be used for small-bore seating tests and assemblies? The narrow profile and high accuracy of M323.099 make it particularly appropriate for small-bore seating tests and precise assembly checks where minimal disturbance is required. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
0.99–10.01 mm Test Pin Set 273 pcs, Grade ±0.004 mm Step 0.1 mm, With Pin Holder, In Case - Metav IndustryLine
Take advantage of a wide diameter range (0.99–10.01 mm), high mechanical accuracy (±0.004 mm) and a comprehensive 273-piece composition for consistent diameter verification — supplied ready for transport in a protective case. Order the set directly via Metav Werkzeuge or consult our specialists for application guidance. Gauge pin set M318.526 — 273-piece precision gauge pins, 0.99–10.01 mm, ±0.004 mm (Metav IndustryLine) Gauge pin set M318.526 is a workshop-grade series of precision gauge pins designed for diameter inspection, plug checking and go/no-go verification across production and quality-control environments. 273-piece precision gauge pin set Diameter range 0.99–10.01 mm Tolerance ±0.004 mm Increment 0.1 mm steps Supplied in transport case Faster, repeatable diameter checks with measurable accuracy A compact inspection workflow relies on reproducible results; this gauge pin set delivers that by combining a dense diameter progression with a tight manufacturing tolerance. The ±0.004 mm specification defines the mechanical accuracy of each pin, which reduces ambiguity when checking bore sizes, alignment fits or reference gauges. The 0.1 mm step size balances speed and resolution: simpler than micro‑step sets yet precise enough for routine production control. Because the pins are made from special steel, they offer the stiffness and dimensional stability needed for repeated contact checks, helping to shorten inspection cycles and increase throughput at the measuring bench. Practical range and handling for everyday workshop tasks Covering 0.99–10.01 mm in incremental steps, the set provides a broad working window that suits a variety of small- to medium-diameter components without the need to swap between multiple kits. The pins are supplied in a transport case that organises the set and protects measurement faces during storage and movement; a probe holder is included to facilitate safe handling and to keep the measuring points accessible during routine checks. This arrangement reduces set‑up time at the workstation and lowers the risk of incorrect pin selection, supporting faster decision‑making on pass/fail checks in the shop floor environment. Designed for consistent application and durability For workshops that demand dependable instruments rather than disposable items, the construction from special steel provides wear resistance and dimensional integrity across many cycles. The set includes an over/under indication of ±0.01 mm, enabling simple comparative checks where small allowance limits are required. Delivered as a 273-piece workshop version, it is tailored for machinists, toolmakers and quality engineers who need a reliable ensemble for gauge, fixture and jig verification. The organised layout and robust materials reduce long‑term maintenance and make the set a practical investment for repeatable inspection tasks. Contact Metav Werkzeuge to discuss suitability for specific inspection tasks, request procurement details or arrange a technical consultation — Metav Werkzeuge, Parkring 45, Emmerich; phone +49 2822 7131930; info@metav-werkzeuge.com Technical Data Article number: M318.526 GTIN: 4054469129167 Customs tariff number: 90173000 Facts Set pieces: 273 Diameter range: 0.99–10.01 mm Increment: 0.1 mm Accuracy: ±0.004 mm Length: 50 mm Weight: 5.6 kg Special features Material: Special steel Supplied in transport case Includes probe holder Over/under indication ±0.01 mm Workshop version FAQ What diameter range does the set cover? The gauge pin set M318.526 covers diameters from 0.99 mm up to 10.01 mm in 0.1 mm steps, providing broad coverage for small to mid‑size bores. What accuracy can be expected from the pins? Individual pins are manufactured to a mechanical accuracy of ±0.004 mm; in addition the set provides an over/under indication of ±0.01 mm for comparative checks. Which material is used for the pins and how robust are they? Pins are made from special steel that offers good stiffness and wear resistance for routine workshop inspection and repeated contact measurements. Is the set ready for transport and storage? Yes, the ensemble is supplied in a protective transport case and includes a probe holder for secure organisation and safe handling. What applications suit this gauge pin set? The set is intended for diameter verification, plug checking, fixture set‑up and go/no‑go inspections in production, toolmaking and quality control environments. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
0.99–4.01 mm Gauge Pin Set With Pin Holder, Step Sizes 1–4 mm / ±0.01 mm, 0.1 mm Graduations - Metav IndustryLine
Take advantage of the robust special steel construction and the comprehensive 93-piece range to standardise small-diameter verifications with repeatable accuracy; the set’s fine 0.1 mm graduations and tight ±0.004 mm accuracy support efficient batch inspections. Order the gauge pin set directly via Metav Werkzeuge or ask our consultants if needed. Gauge pin set M318.527 — 93-piece precision kit, 0.99–4.01 mm The Gauge pin set M318.527 is a compact verification kit for precise hole and shaft checks in toolrooms, quality control and inspection benches. 93-piece precision range Special steel construction Diameter increment 0.1 mm Probe holder included Consistent precision for everyday inspection The set delivers high-repeatability measurements across a tightly packed range from 0.99–4.01 mm, making it suitable for small-diameter inspections in component production and maintenance. The narrow diameter steps and 0.1 mm graduation allow quick selection of the required pin size, while the specified accuracy ±0.004 mm provides confidence when checking bore limits or verifying gauges. Presented as a consolidated verification kit, the collection reduces tool changes and speeds up routine quality checks without compromising on metrological reliability. Designed for efficient workshop workflows A complete 93-piece kit simplifies organisation during serial testing and prototyping tasks: clear incremental sizes limit selection time and the included probe holder secures pins for repeatable measurements or fixture-based checks. The special steel material balances wear resistance with dimensional stability so that the set remains suitable for frequent use in production environments. Practical grouping and steady handling characteristics make this set a pragmatic choice where throughput and consistent pass/fail decisions are the priority. Practical handling and traceable identification Pins in the set are arranged to support rapid verification sequences and to reduce handling errors during frequent swaps. The compact kit format supports workplace logistics in inspection stations and mobile verification tasks across the shop floor. For documentation purposes, the set’s range and stated tolerance allow straightforward comparison against drawing tolerances and inspection records, helping to maintain traceability in quality-management processes. For purchasing or technical advice on the Metav IndustryLine gauge pin solutions, contact Metav Werkzeuge in Emmerich: info@metav-werkzeuge.com or +49 2822 7131930 — specialists will assist with specifications and order placement Technical Data Article number: M318.527 GTIN: 4054469156132 Manufacturer: Metav IndustryLine Facts Pieces: 93 Diameter range: 0.99–4.01 mm Graduation: 0.1 mm Accuracy: ±0.004 mm Weight: 5.6 kg Special features Material: special steel Includes probe holder Set for hole and shaft verification Compact organisation for shop-floor use FAQ What diameter range does the set cover? The set covers diameters from 0.99 to 4.01 mm for fine small-bore inspections. How many pins are included in the kit? The kit contains 93 pins arranged to provide continuous increments across the specified range. What is the stated measurement accuracy? Measurement accuracy is specified as ±0.004 mm for the verification range. What material are the pins made from? Pins are manufactured from special steel, chosen for durability and dimensional stability. Is a holder included for handling? Yes, the set includes a probe holder to support secure handling and fixture use. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
0.9mm Test Pin Length 50mm ±0.001 mm, Workshop Version, Special Steel in Case - Metav IndustryLine
Take advantage of the combination of ±0.001 mm tolerance, compact Ø 0.90 mm / 50 mm geometry and workshop‑grade material for dependable in‑process checking and repeatable end‑measure control. Order the gauge pin directly via Metav Werkzeuge or consult the Metav team for specification matching. Gauge pin M323.090 — single measuring pin, Ø 0.90 mm, 50 mm (Metav IndustryLine) The Gauge pin M323.090 is a single workshop‑grade measuring pin designed for precise end‑measurement and bore checking in production and inspection environments. Precision ±0.001 mm tolerance Diameter 0.90 mm, length 50 mm Workshop‑grade special steel Delivered in protective transport case Precise tolerance for reliable process control A tolerance of ±0.001 mm places this measuring pin in the category for fine metrology tasks where repeatability matters. The very small allowance reduces uncertainty in go/no‑go checks and comparator setups, enabling consistent inspection decisions and minimising rework. By providing a clearly defined measurement standard, the pin supports tighter process control and faster acceptance of produced features, improving throughput without compromising quality. Compact geometry and durable workshop design The compact Ø 0.90 mm diameter combined with a 50 mm usable length allows access into narrow bores and confined features while retaining sufficient stiffness for routine handling. Manufactured from special steel, the design emphasises wear resistance and dimensional stability under workshop conditions. The workshop execution ensures robustness in daily use, thus extending the service interval and reducing the need for frequent replacements. Practical supply and integration into inspection routines Supplied as a single measuring pin in a protective transport case, the item is ready for secure storage and rapid deployment at the inspection bench. The clear identification (SKU M323.090, GTIN 4061905054945) simplifies inventory control and traceability in production settings. The pin is particularly well suited for end‑measure checks and regular bore verification, offering a compact, low‑complexity solution that supports reliable measurement routines with minimal setup time. For swift supply of workshop‑grade gauge pins and application advice, contact Metav Werkzeuge in Emmerich — the Metav team provides specification support and reliable delivery for production and inspection needs. Technical Data SKU: M323.090 GTIN: 4061905054945 Material: Special steel Tolerance: ±0.001 mm Length: 50 mm Diameter: 0.90 mm Weight: 0.003 kg Facts Diameter: 0.90 mm Length: 50 mm Tolerance: ±0.001 mm Weight: 0.003 kg Category: Gauge pins (Messstifte) Special features Workshop design Protective transport case for delivery Single measuring pin for end measurements Suitable for end‑measure and bore checking FAQ What measurement accuracy does this pin provide? The M323.090 gauge pin offers an accuracy of ±0.001 mm, suitable for fine inspection tasks and repeatable end‑measure control. Which applications are typical for this measuring pin? Applications include end‑measure checking, bore verification and production inspection where a compact, precise reference pin simplifies pass/fail evaluation. Is the pin delivered ready for storage and transport? Yes — the pin is supplied in a protective transport case to secure the component during transport and storage and to reduce handling damage. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
1 1/2" UNC Go Thread Ring Gauge 6 TPI ANSI B1.1 2A - Metav IndustryLine
Take advantage of a hardened GO ring gauge that matches ANSI/ASME B1.1 tolerances and delivers reproducible pass/fail checks for external threads; the combination of standard conformity, robust gauge steel and compact handling supports efficient in-process inspection. Order the gauge directly via Metav Werkzeuge or consult the Metav team for application advice. Thread ring gauge UNC GO — 1 1/2" x 6, tolerance class 2A (Metav IndustryLine) The Thread ring gauge UNC GO, 1 1/2" x 6, ANSI/ASME B1.1, 2A is a hardened go ring intended for rapid acceptance checks of external UNC threads in machining and assembly environments. UNC Go ring gauge 1 1/2" x 6 Hardened gauge steel construction Tolerance class 2A, ANSI/ASME B1.1 Designed for manufacturing quality control Faster in-line acceptance with standardised GO checks A dedicated GO ring gauge simplifies routine inspections by confirming that external UNC threads are within the permitted 2A envelope. By applying a single go/no-go decision criterion, the gauge reduces inspection time and avoids ambiguous manual measurements, supporting consistent throughput on the shop floor. The gauge’s specification to ANSI/ASME B1.1 means compatibility with widely used UNC thread systems, enabling straightforward integration into existing quality control procedures and sampling plans. Durable design for reproducible results across production shifts Manufactured from hardened gauge steel, the ring gauge offers wear resistance and dimensional stability that sustain repeatable results under frequent use. The compact nominal size 1 1/2" x 6 and clear tolerance class make the tool straightforward to store and handle during inspection cycles. Supplied as article M315.965, the component’s construction minimises scoring and false readings, which in turn reduces unnecessary rework and downtime within fabrication and inspection workflows. Practical fit for shop-floor and QA environments Intended for external thread verification, this go-only ring is optimised for pass/fail evaluations where a single confirmation is required before assembly or shipment. The 2A tolerance classification identifies the gauge specifically for external threads, clarifying its role in inspection plans and preventing misuse. When used as part of a controlled sampling routine, the gauge contributes to traceable quality records and supports decision-making that keeps production moving without compromises to conformance. Contact Metav Werkzeuge for tailored advice or to arrange supply of this Metav IndustryLine ring gauge — email info@metav-werkzeuge.com or call +49 2822 7131930 for direct assistance from Emmerich. Technical Data Article number: M315.965 GTIN: 4054469180540 Material: Hardened gauge steel Standard: ANSI/ASME B1.1/B1.2 Size: 1 1/2" x 6 Tolerance class: 2A Weight: 0.7 kg Facts Thread pitch: 6 tpi Nominal size: 1 1/2" Weight: 0.7 kg Special features Go gauge for external threads Tolerance class 2A (external threads) Compliance with ANSI/ASME B1.1/B1.2 Suitable for manufacturing quality control Category: Gauges FAQ What does the GO designation mean for this ring gauge? The GO designation indicates the ring is used to confirm that external threads meet the minimum form and size requirements; the Thread ring gauge UNC GO, 1 1/2" x 6, ANSI/ASME B1.1, 2A permits parts that pass the gauge to proceed without further thread-size rejection checks. Is this gauge suitable for production sampling on UNC threads? Yes — the ring gauge is manufactured to ANSI/ASME B1.1 and is specifically designed for quick acceptance checks of UNC external threads in production environments. What materials is the gauge made from and how does that affect service life? The gauge is made from hardened gauge steel, providing high wear resistance and dimensional stability that prolongs service life under frequent shop-floor use. Can this gauge be used for internal threads or for NO-GO evaluation? This item is a GO ring intended for external thread acceptance; it does not serve as a NO-GO or internal thread gauge and should be used accordingly in inspection routines. How should the gauge be stored and handled to maintain accuracy? Store the ring in a clean, dry environment and avoid impacts or contamination. Regular visual checks and periodic dimensional verification maintain reliability for shop-floor inspections. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
1 1/2" UNC Go/No-Go Thread Ring Gauge 6 TPI, Hardened Gauge Steel ANSI/ASME B1.1/B1.2 - Metav IndustryLine
Take advantage of the combination of ANSI/ASME conformity, the NOGO go/no-go function and the durable hardened gauge steel for reliable, fast thread inspection. Order the gauge directly via Metav Werkzeuge or consult our specialists for application advice. Thread ring gauge UNC NOGO, 1 1/2 x 6, ANSI B1.1 — NOGO inspection gauge by Metav IndustryLine Thread ring gauge UNC NOGO, 1 1/2 x 6 ANSI B1.1 2A designed for rapid go/no-go verification of external UNC threads in workshop and production environments Hardened gauge steel for durable wear resistance ANSI/ASME B1.1 compliance for standardised inspection NOGO ring for quick go/no-go verification Compact design, nominal weight 0.7 kg Rapid, standard-compliant verification to protect production quality The NOGO thread ring gauge is engineered to provide a fast, objective decision on external UNC threads, reducing downstream rework and scrap. Built to the ANSI/ASME B1.1/B1.2 specification with tolerance class 2A, the gauge delivers inspection results that align with widely accepted US thread standards. The NOGO function prevents acceptance of undersized or incomplete external threads by failing parts that do not meet the required form, which streamlines quality control and shortens cycle times on the shop floor. The combination of clear pass/fail logic and compliance with an established standard supports traceable, auditable inspection processes. Durable construction for repeatable measurements and low life-cycle cost Manufactured from hardened gauge steel, the ring offers high wear resistance and retains form under regular use, making it suitable for repetitive checks in production runs. The compact form factor and the nominal weight of 0.7 kg make handling straightforward at inspection stations while still offering sufficient mass for stable engagement with threaded parts. Reduced maintenance intervals and predictable wear behaviour contribute to a lower total cost of ownership compared with softer materials. When stored and used in line with standard good-practice inspection routines, the gauge sustains dimensional integrity and supports consistent results across many inspection cycles. Traceability and workshop integration for quality assurance Identified as M315.995 and supplied with a clear label and GTIN, the ring gauge is easy to document within quality-management systems and inventory records. The device is intended exclusively for go/no-go checks of external UNC threads with a nominal size of 1 1/2" and a pitch of 6 tpi, providing unambiguous applicability for engineering and maintenance teams. Its simple operation supports quick training of inspectors and straightforward integration into first-article inspection or in‑process control routines. Where formal record-keeping is required, the gauge's standard references facilitate conformity reports and help maintain consistent production tolerances. For assured thread inspection and workshop-ready measuring equipment, request the Metav IndustryLine NOGO thread ring gauge via Metav Werkzeuge — our Emmerich team will advise on suitability and delivery options Technical data Article number: M315.995 GTIN: 4054469181189 Label: Gewinde-Lehrring UNC NOGO, 1.1/2 x 6 ANSI B1.1 / 2A Facts Weight: 0.7 kg Thread size: 1 1/2" Pitch: 6 tpi Tolerance class: 2A Special features Material: hardened gauge steel Type: NOGO ring gauge for external threads Standard: ANSI/ASME B1.1/B1.2 Use: go/no-go inspection of external UNC threads FAQ What size and pitch does this ring gauge check? The ring gauge verifies external UNC threads of nominal size 1 1/2" with a 6 tpi pitch. Is the gauge compliant with recognised standards? Yes — this NOGO ring gauge is manufactured to ANSI/ASME B1.1/B1.2 and supplied as tolerance class 2A for standardised inspection. What material is the gauge made from and why does it matter? Constructed from hardened gauge steel, the ring ensures long-term wear resistance and repeatable dimensional stability during routine checks. How is the product identified for inventory and traceability? The gauge is listed as M315.995 and carries the GTIN 4054469181189 to simplify documentation and stock control. Can this gauge be used for internal thread inspection? No — the device is a NOGO ring gauge specifically for external thread verification; internal thread checking requires the corresponding plug gauge. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
1 1/2" UNEF Thread Go Gauge, Right-Hand, 18 TPI, ANSI B1.1 2A - Metav IndustryLine
Take advantage of precise, repeatable thread verification through ANSI/ASME B1.1 compliance, hardened gauge-steel construction and a compact, easy-to-handle form factor for consistent production control. Order the thread ring gauge directly via Metav Werkzeuge or request specialist advice from our consultants for application guidance. Thread ring gauge UNEF GO 1 1/2" x 18, 2A — Metav IndustryLine Thread ring gauge UNEF GO 1 1/2" x 18, 2A for verification of external UNEF threads in machining and inspection environments according to ANSI/ASME standards UNEF 1 1/2" x 18 GO gauge Hardened gauge steel construction ANSI/ASME B1.1/B1.2 compliance Tolerance class 2A for external threads Reliable conformity assurance for production control The GO ring gauge is designed to confirm that external threads meet maximum-material-size requirements defined by ANSI/ASME B1.1. Built to the 2A tolerance, this gauge provides a clear, pass/fail check that reduces subjective judgement during inspection and helps maintain throughput by lowering false rejects. By integrating a standardised check tool into the workflow, measurement uncertainty from manual comparison is minimised and repeatable measurements become part of routine quality control. Durable construction for sustained workshop use Manufactured from hardened gauge steel, the instrument offers wear resistance and dimensional stability over prolonged use, supporting consistent results across production batches. The designation as a GO gauge means it must freely enter a compliant external thread; failure to pass indicates oversize material or incorrect pitch. The item is finished for right-hand applications and its compact mass (0.7 kg) eases handling during frequent inspections while preserving the necessary profile stiffness for accurate verification. Practical fit for inspection benches and toolrooms Suited to machine shops, toolrooms and incoming inspection, the gauge simplifies thread acceptance procedures and feeds directly into documented quality processes. Traceability is supported by standard identifiers and durable marking, assisting in batch records and audits. Supplied by a quality-conscious partner, the device contributes to dependable traceable inspection routines and helps embed consistent thread verification into everyday production management. For dependable thread verification and application advice, contact Metav Werkzeuge for ordering or technical consultation — Metav IndustryLine items are available directly from our Emmerich facility Technical data Article number: M315.965.EF GTIN: 4054469180557 Brand: Metav IndustryLine Facts Thread form: UNEF Size: 1 1/2" Pitch: 18 tpi Tolerance class: 2A Weight: 0.7 kg Special features GO ring gauge Material: hardened gauge steel Standard: ANSI/ASME B1.1/B1.2 Direction: right-hand thread FAQ What does a GO ring gauge verify? The GO ring gauge checks that an external UNEF thread meets the maximum-material-size requirement; the Thread ring gauge UNEF GO 1 1/2" x 18, 2A confirms acceptance when the thread enters freely. Is this gauge suitable for routine shop inspection? Yes. The Metav IndustryLine GO ring gauge is designed for workshop and inspection-bench use, providing quick go/no‑go results for production control. Which standard does the gauge conform to? The ring gauge is produced to ANSI/ASME B1.1/B1.2 specifications and is manufactured for the 2A external-thread tolerance class. What material and durability can be expected? Constructed from hardened gauge steel, the gauge is resistant to wear and maintains dimensional stability during regular inspection cycles. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
1 1/2" UNEF Thread Plug Gauge 18 TPI Right-Hand Hardened Gauge Steel ANSI B1.1/B1.2 - Metav IndustryLine
Take advantage of a standards‑based inspection tool that combines UNEF 1 1/2" x 18 sizing, tolerance class 2B and hardened gauge steel construction for reliable, repeatable checks of internal threads; order the gauge directly via Metav Werkzeuge or consult our specialists for application advice. Thread plug gauge UNEF, 1 1/2" x 18, class 2B — Metav IndustryLine Thread plug gauge UNEF, 1 1/2" x 18, class 2B suitable for checking internal UNEF threads to ANSI/ASME B1.1/B1.2 standards in production and inspection environments Right-hand UNEF 1 1/2" x 18 Conforms to ANSI/ASME B1.1/B1.2 Hardened gauge steel construction Tolerance class 2B for internal threads Fast, standards-based pass/fail inspection that reduces rework A compact, robust male gauge enables quick verification of internal threads according to ANSI/ASME B1.1/B1.2, ensuring compatibility with mating bolts and assemblies. The UNEF form at 1 1/2" x 18 tpi provides a clear go/no‑go result, which shortens inspection time and reduces the risk of assembly failures. For production lines and maintenance tasks, this method translates directly into fewer rejects and lower rework costs. Durable construction for consistent results over time Manufactured from hardened gauge steel, the unit resists wear from repeated engagement and preserves gauge geometry across many inspection cycles. The right‑hand thread design is optimised for standard fastening directions and the 2B tolerance reflects the internal thread acceptance class typically required in mechanical engineering. The material choice and heat treatment together deliver long service life and reliable dimensional stability. Simple integration into quality control workflows The plug style allows straightforward insertion into the component; a pass indicates conformity to the 2B acceptance class while a no‑go detects undersize or imperfect threads. This direct method supports traceable quality routines and can be documented in routine inspection records. For workshops requiring repeatable checks, the gauge is an efficient addition to first article inspection and random sampling programmes. Confidence at procurement and on the shop floor Specifying a gauge that adheres to recognised standards removes ambiguity in procurement and assures downstream teams that incoming parts meet mechanical expectations. The combination of clear standards compliance, robust hardened gauge steel construction and a defined tolerance class provides both technical certainty and practical peace of mind when selecting inspection tools for series production or repair operations. Contact Metav Werkzeuge for expert advice on integrating the Metav IndustryLine thread plug gauge into inspection processes — phone +49 2822 7131930 or eMail info@metav-werkzeuge.com Technical data Article number: M315.935.EF GTIN: 4054469179919 Weight: 0.8 kg Material: hardened gauge steel Standard: ANSI/ASME B1.1/B1.2 Facts Size: 1 1/2" Pitch: 18 tpi Tolerance class: 2B Tariff number: 90173000 Special features Right-hand thread Thread form: UNEF (Unified Extra Fine) Product type: Thread plug gauge Categories: Gauge pins; Gauges FAQ What does the tolerance class 2B mean for internal threads? Tolerance class 2B specifies the internal thread acceptance limits for standard engineering practice; the Thread plug gauge UNEF, 1 1/2" x 18, class 2B checks internal threads against those limits to confirm conformity. Is this gauge suitable for production sampling or only for final inspection? The Metav IndustryLine plug gauge is suitable for both production sampling and final inspection thanks to its hardened construction and standards‑based dimensions. Does the gauge indicate whether a thread is damaged or simply out of tolerance? A no‑go result from the Thread plug gauge UNEF, 1 1/2" x 18, class 2B indicates the internal thread fails to meet the specified tolerance; further assessment is required to distinguish between damage and dimensional error. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
1 1/2" UNF Thread Go Gauge 12 TPI Right-Hand, Hardened Gauge Steel ANSI/ASME B1.1/B1.2 - Metav IndustryLine
Take advantage of a hardened gauge steel construction combined with strict ANSI/ASME B1.1/B1.2 conformity and a 2B tolerance to ensure reliable verification of internal UNF threads; order the plug gauge directly via Metav Werkzeuge or contact our consultants for application advice. UNF Thread Plug Gauge 1 1/2" × 12 – Metav IndustryLine (Tolerance 2B, hardened gauge steel) a UNF Thread Plug Gauge 1 1/2" × 12 for precise verification of internal threads to ANSI/ASME B1.1, designed for workshop and inspection use Hardened gauge steel construction ANSI/ASME B1.1/B1.2 conforming Tolerance class 2B for internal threads Right-hand UNF 1.5" × 12 thread Accurate verification for UNF internal threads with minimal rework The UNF Thread Plug Gauge 1 1/2" × 12 serves as a concise pass/fail control for internal threads, cutting inspection time and reducing scrap. With a 12 TPI thread form and tolerance class 2B, the gauge confirms thread geometry and fit according to the ANSI/ASME B1.1 specification, enabling quick decisions on component acceptability. By standardising the verification step, workshop quality checks become repeatable and transparent, supporting faster process control and fewer production interruptions. Robust construction for frequent use and long service life Manufactured from hardened gauge steel, the plug gauge resists wear in high‑use inspection environments and preserves the reference form over many cycles. The material choice and heat treatment ensure dimensional stability and resistance to corrosion in normal workshop conditions; periodic cleaning and protective storage prolong service life. The compact, solid design gives a reliable tactile feel at the seating point, which helps inspectors detect marginal fits without complex measurement equipment. Conformity and traceability that support quality systems Compliance with ANSI/ASME B1.1/B1.2 and the clear marking of 2B tolerance class simplify documentation for incoming inspection and production control. Integration of the gauge into inspection plans provides objective evidence for quality audits and helps maintain consistent assembly performance. The tool is suitable for routine shop-floor checks where a definitive go/no‑go decision streamlines downstream operations and reduces rework cycles. Practical workshop integration and handling notes The right‑hand UNF 1.5" × 12 geometry makes this gauge immediately applicable for American‑standard thread forms commonly found in heavy‑duty fittings and assemblies. The unit’s moderate mass supports controlled insertion and removal during checks; normal practice recommends cleaning threads before use and storing the gauge in a dry environment to keep the reference form intact. Where extended traceability is required, include the gauge identity and inspection results in the production record to support continuous quality improvement. Contact Metav Werkzeuge for application advice and to secure the hardened Metav IndustryLine UNF thread plug gauge (SKU M315.935.F), available for prompt dispatch from Emmerich. Technical data Article number: M315.935.F GTIN: 4054469179926 Label: Gewinde-Lehrdorn UNF, 1.1/2 x 12 ANSI B1.1 / 2B Manufacturer: Metav IndustryLine Facts Size: 1 1/2" × 12 TPI Pitch: 12 TPI Weight: 0.8 kg Tariff number: 90173000 Special features Material: gauge steel, hardened Right-hand thread Tolerance class: 2B Standard: ANSI/ASME B1.1/B1.2 Categories: Gauges; Measuring pins FAQ What is this gauge used for? The UNF Thread Plug Gauge 1 1/2" × 12 is used to verify internal UNF threads for conformity to ANSI/ASME B1.1 and to provide a clear go/no‑go result for assembly acceptance. What does tolerance class 2B mean for inspection? Tolerance class 2B denotes the standard internal‑thread tolerance in the ANSI/ASME system; the gauge confirms that the internal thread meets the dimensional allowance and fit expectations. Which materials is the gauge suitable for when inspecting threads? The plug gauge is a verification tool and may be used to inspect threads produced in steel, aluminium and other common construction materials; the gauge itself is made from hardened gauge steel for durability. How should the gauge be cared for to retain accuracy? Clean thread flanks before and after use, store the gauge dry and protected, and avoid impacts; routine visual checks preserve the reference form and support reliable inspections. Can this gauge be used for external threads? This plug gauge is designed for internal thread verification; external threads require the corresponding plug/gauge type or a thread ring gauge for a definitive assessment. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
1 1/2" UNF Thread Ring Gauge 1.1/2 x 12 TPI GO, Hardened Gauge Steel, ANSI/ASME B1.1/B1.2 - Metav IndustryLine
Take advantage of fast, repeatable thread verification with a GO thread ring gauge made from hardened gauge steel, compliant with ANSI/ASME B1.1 tolerances; order the gauge directly via Metav Werkzeuge or ask our consultants if needed. Thread ring gauge UNF GO 1 1/2" x 12, ANSI B1.1 – Metav IndustryLine A Thread ring gauge UNF GO 1 1/2" x 12 for quick verification of external UNF threads in production and inspection workflows UNF GO gauge for 1 1/2" x 12 threads Conforms to ANSI/ASME B1.1/B1.2 standard Hardened gauge steel construction Tolerance class 2A for external threads Fast and reliable thread verification for production lines A dedicated GO thread ring gauge speeds up acceptance checks on turned and machined shafts by providing a single, unequivocal pass criterion. Sized for 1 1/2" x 12 UNF threads with a 12 tpi pitch and 2A tolerance class, this gauge is designed to check external UNF threads against the ANSI/ASME B1.1 profile quickly and repeatedly. Using a GO-only ring eliminates ambiguity during rapid throughput inspections: a fit confirms the thread meets minimum material and form requirements, which supports faster in-process decisions and reduces the time spent at the inspection stage. Built for durability and consistent results in the workshop Constructed from hardened gauge steel, the ring offers high wear resistance and dimensional stability, which helps maintain repeatability across many cycles. The right-hand thread orientation matches standard production threads and the robust build minimises deformation under normal handling, so the ring remains a reliable pass gauge over extended use. The compact, single-gauge format simplifies storage and handling on the shop floor while delivering the mechanical resilience expected in machining and quality-control environments. Seamless integration into quality control routines Conformity to ANSI/ASME B1.1/B1.2 makes the ring gauge a straightforward choice for firms aligning with international thread standards. The gauge supports standardised inspection procedures, shortens cycle times for thread verification and contributes to reduced scrap and rework by detecting out-of-spec parts early. Its clear pass/fail logic complements digital data collection or manual logging in existing workflows, enhancing traceability and process discipline without complex setup. Contact Metav Werkzeuge today for tailored procurement advice and secure this GO thread ring gauge for your inspection bench — call +49 2822 7131930 or email info@metav-werkzeuge.com Technical Data Article number: M315.965.F GTIN: 4054469180564 Label: Thread ring gauge UNF GO, 1 1/2" x 12 ANSI B1.1 / 2A Facts Thread size: 1 1/2" x 12 (UNF) Threads per inch: 12 tpi Tolerance class: 2A Weight: 0.7 kg Special features Material: hardened gauge steel Norm: ANSI/ASME B1.1/B1.2 Thread direction: right-hand thread Tariff code: 90173000 eCl@ss: 21170214 FAQ What is the primary use of this ring gauge? The Thread ring gauge UNF GO 1 1/2" x 12 is used to verify acceptance of external UNF threads to the ANSI/ASME B1.1 profile; a pass indicates the thread meets minimum form and size criteria. Does this gauge check against international standards? Yes — the ring is manufactured to conform with ANSI/ASME B1.1/B1.2, ensuring compatibility with common UNF thread specifications. Is this a GO or NO-GO gauge? This item is a GO ring gauge only; it confirms whether a shaft or external thread is within the lower and nominal tolerances required for acceptance. What material is the gauge made from and how durable is it? The ring is made from hardened gauge steel, offering enhanced wear resistance and long-term dimensional stability suitable for regular shop-floor use. Can this gauge be used for left-hand threads? No — this ring is produced with a right-hand thread; left-hand threads require a dedicated left-hand ring. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
1 1/4" 7 TPI UNC NOGO Thread Ring Gauge, Hardened Gauge Steel, ANSI B1.1/B1.2 - Metav IndustryLine
Take advantage of hardened gauge steel, ANSI/ASME B1.1 conformity and the precise 2A tolerance class to ensure consistent thread inspection and reduce production rejects; order the ring gauge directly via Metav Werkzeuge or consult our specialists for application advice. Thread Ring Gauge (UNC NOGO) 1 1/4" × 7, ANSI B1.1 / 2A — Metav IndustryLine The Thread Ring Gauge UNC NOGO, 1 1/4" × 7, ANSI B1.1 / 2A is a go/no-go ring gauge designed for fast verification of external UNC threads in production and quality control environments. NOGO ring gauge for UNC 1 1/4" × 7 Hardened gauge steel construction Conforms to ANSI/ASME B1.1/B1.2 standards Tolerance class 2A for form and pitch Reliable thread verification that reduces rework A dedicated NOGO ring gauge provides an immediate, objective decision at the production line. Manufactured from hardened gauge steel, this go/no-go instrument resists wear and preserves its contact geometry over repeated checks, which translates into stable limits and fewer false rejections. Conformance to ANSI/ASME B1.1 ensures that thread form, pitch and major diameter fall within the internationally recognised UNC specification, enabling consistent interchangeability of fasteners and avoiding costly rework cycles. Robust design for repeatable measurements The gauge’s geometry and 2A tolerance class are selected to match standard external thread requirements, offering clear acceptance criteria during rapid inspections. The compact, metal-ring construction concentrates load paths and minimises elastic deformation, so the limiting condition is reproducible from part to part. In practice, this means line operators and inspectors can record dependable pass/fail results without complex fixtures, improving throughput while maintaining documented quality control. Practical fit into quality systems and traceability As a simple tool for routine checks, the ring gauge integrates easily into incoming inspection, in-process control and final checks. The physical limit-test method complements dimensional measuring instruments by delivering a quick verification against the specification; this accelerates sorting and prevents non-conforming components reaching assembly. When documented traceability is required, the gauge’s SKU and serial details can be logged in inspection records to support audits and batch release procedures. For assured ANSI-compliant thread control, order this Metav IndustryLine ring gauge via Metav Werkzeuge — contact our Emmerich team at info@metav-werkzeuge.com or +49 2822 7131930 for specification guidance and delivery options Technical data Article number: M315.992 GTIN: 4054469181110 Weight: 0.6 kg Material: hardened gauge steel Standard: ANSI/ASME B1.1/B1.2 Tolerance class: 2A Facts Size: 1 1/4" Pitch: 7 tpi Type: UNC NOGO ring gauge Category: Go/no-go inspection gauge Special features Designed for external thread verification Durable, wear-resistant construction Immediate pass/fail assessment Suitable for production and quality control FAQ What size and thread form does this gauge check? The ring gauge checks external UNC threads at 1 1/4" × 7 tpi and is manufactured to the ANSI/ASME B1.1 specification for UNC form. Is the gauge suitable for production-line checks? Yes, the NOGO ring gauge is intended for rapid, repeatable pass/fail inspections in production and inspection areas and is constructed from hardened gauge steel for longevity. What does tolerance class 2A mean for this gauge? Tolerance class 2A specifies the acceptable form and pitch envelope for external UNC threads; the gauge is matched to that class so measured threads meet common industrial interchangeability requirements. Can this ring gauge replace detailed dimensional measurement? The gauge provides conclusive go/no-go verification and is ideal for routine control; it complements, rather than replaces, detailed measurement when full dimensional documentation or root-cause analysis is required. How should inspection results be recorded for audits? Record the gauge SKU (M315.992), inspection date, operator and part details in the quality log; this supports traceability and audit requirements. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
1 1/4" Thread Go/No-Go Ring Gauge UNF 12 TPI Right-Hand ANSI B1.1/B1.2, Hardened Gauge Steel - Metav IndustryLine
Take advantage of the combination of precise thread verification, hardened gauge steel construction and ANSI/ASME conformity to keep production quality consistent and reduce rework; order the gauge directly via Metav Werkzeuge or consult the technical team for application advice. Thread Ring Gauge No-Go — 1 1/4" x 12 UNF, ANSI/ASME B1.1, 2A (right-hand) The Thread Ring Gauge No-Go (M315.992.F) provides a fast, repeatable check for oversized external UNF threads in production and quality-control environments. No-Go control for oversize external threads Conforms to ANSI/ASME B1.1/B1.2 standards Hardened gauge steel for long service life Tolerance class 2A for fine thread acceptance Assured rejection of non-conforming threads for efficient QC The No-Go ring is designed to identify external threads that exceed allowed limits so that only parts within specification proceed to assembly. Built to the ANSI/ASME B1.1 standard and specified as 2A tolerance, the gauge provides an objective, pass/fail decision that simplifies inspection routines. Using a dedicated rejection gauge reduces cycle time at the control station and lowers the rate of downstream rework by eliminating borderline parts before they enter assembly. Robust construction that keeps inspection stable over time Manufactured from hardened gauge steel, the ring resists wear and maintains its verification geometry under repeated use. The compact ring shape is optimised for workshop handling and ensures stable seating on the workpiece during checks. The instrument’s right-hand thread geometry and nominal size 1 1/4" x 12 UNF match common UNF external threads, enabling consistent comparison to the drawing specification and predictable lifetime performance in industrial environments. Integration with production workflows and traceability The ring gauge serves as a clear, binary control in go/no-go inspection plans and is suitable for integration into routine sampling schemes. Using a standardised ring gauge for no-go verification helps document conformity across production batches and supports quality records required by customers or internal audits. The simple functionality requires minimal training, while the adherence to established standards aids communication with suppliers and inspectors. For guaranteed compliance with ANSI thread requirements and tailored delivery options contact Metav Werkzeuge in Emmerich to secure the M315.992.F No-Go ring gauge and specialist application guidance. Technical data Article number: M315.992.F GTIN: 4054469181134 Tariff number: 90173000 Facts Size: 1 1/4" x 12 UNF Pitch: 12 Weight: 0.6 kg Special features Material: hardened gauge steel Standard: ANSI/ASME B1.1/B1.2 Tolerance class: 2A Thread direction: right-hand Type: No-Go ring gauge FAQ What is this gauge used for? The No-Go ring gauge M315.992.F is used to check whether external UNF 1 1/4" x 12 threads exceed the maximum material condition and therefore must be rejected. Which standard does the gauge follow? This ring gauge conforms to ANSI/ASME B1.1/B1.2, so inspection results align with common UNF thread specifications. What material is the gauge made from and why does that matter? The gauge is manufactured from hardened gauge steel, which gives the M315.992.F durable wear resistance and consistent geometric stability during repeated inspections. What does the 2A tolerance class indicate? Tolerance class 2A specifies the acceptable fit and clearance for external threads; the No-Go ring verifies the thread does not exceed the allowances set by that class. Can this gauge be used on left-hand threads? No; the M315.992.F is produced for right-hand UNF threads and should only be used with matching thread direction. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
1 1/4" Thread Plug Gauge UNF 12 TPI Right-Hand ANSI B1.1/B1.2, Hardened Gauge Steel - Metav IndustryLine
With its combination of hardened gauge steel construction and conformity to ANSI/ASME B1.1/B1.2, this thread plug gauge ensures repeatable verification of internal UNF threads. The 2B tolerance and 1 1/4" x 12 tpi sizing make it suitable for both production control and incoming inspection. Order via Metav Werkzeuge or contact our consultants for specification support. Thread plug gauge UNF, 1 1/4 x 12 ANSI B1.1 / 2B — hardened gauge steel, right-hand thread (Metav IndustryLine) The Thread plug gauge UNF, 1 1/4 x 12 ANSI B1.1 / 2B is a hardened internal-thread gauge designed for precise verification of UNF threads to ANSI/ASME tolerances in workshop and quality-control environments ANSI/ASME B1.1/B1.2 conformity Hardened gauge steel construction Right-hand thread design Tolerance class 2B for internal threads Engineered for reproducible thread verification Built to match industry standards, the plug verifies internal UNF threads with a clear specification: 1 1/4" x 12 tpi and 2B tolerance per ANSI/ASME B1.1/B1.2. This makes the instrument suitable for repeatable pass/fail checks during production sampling and incoming inspections, reducing ambiguity at the control stage. The defined thread form and pitch ensure that measurements relate directly to commonly used UNF components and fasteners, simplifying documentation and audit trails in regulated processes. Robust material and workshop handling Manufactured from hardened gauge steel, the gauge resists wear during repetitive use while retaining dimensional stability. The compact mass of approximately 0.6 kg provides a comfortable balance between sturdiness and manoeuvrability at the inspection bench. A right-hand thread orientation matches standard UNF parts, avoiding adaptation steps in everyday checking routines. The material choice and heat treatment together extend service life and preserve gaugeability under typical shop conditions, lowering total cost of ownership through reduced replacement frequency. Practical fit in quality workflows As a dedicated internal-thread verifier, the plug integrates easily into workshop routines and quality-control sequences. Marking the go/no-go outcome is straightforward because the gauge is produced to the ANSI/ASME norms commonly cited in technical drawings and specifications. Using a standardised gauge removes subjective judgment from the inspection step and speeds throughput in serial production. For traceability, record the gauge identification (SKU M315.932.F) alongside inspection results to maintain a clear audit trail for batch releases and supplier checks. Reliability through a specialist partner Choosing a Metav IndustryLine instrument aligns the tool with a supplier that emphasises accessible precision and reliable delivery. Metav’s offering is backed by decades of distribution experience and a broad product range, which supports consistent replenishment and tool matching across workshops. This combination of durable construction and established distribution channels helps to lower operational risk, ensuring that measurement capability remains available when needed and that replacement items conform to the same specifications. Contact Metav Werkzeuge for specification confirmation and supply from Emmerich—call +49 2822 7131930 or e‑mail info@metav-werkzeuge.com Technical data Article number: M315.932.F GTIN: 4054469179858 SKU: M315.932.F Weight: 0.6 kg Material: hardened gauge steel Norm: ANSI/ASME B1.1/B1.2 Core specifications Size: 1 1/4" Pitch: 12 tpi Tolerance class: 2B Thread direction: right-hand Standards & features ANSI/ASME B1.1/B1.2 compliance Right-hand UNF thread Category: Gauges / plug gauges Customs tariff number: 90173000 FAQ What thread size and pitch does this gauge check? The Thread plug gauge UNF, 1 1/4 x 12 ANSI B1.1 / 2B checks internal UNF threads with a nominal size of 1 1/4" and a pitch of 12 threads per inch; the item is listed as SKU M315.932.F from Metav IndustryLine. Which tolerance class applies to this gauge? This plug gauge is produced to tolerance class 2B, which corresponds to the standard internal-thread tolerance for general-purpose UNF assemblies under ANSI/ASME B1.1. What material is the gauge made from and why does that matter? The gauge is made from hardened gauge steel; this material and heat treatment maintain dimensional stability and wear resistance, ensuring long-term reliability for routine inspection tasks. To which standards does the gauge conform? Conformity is to ANSI/ASME B1.1/B1.2, the common reference for UNF thread forms and tolerances used in engineering drawings and inspection plans. How should the gauge be recorded in inspection documentation? Record the tool by its designation and SKU (Thread plug gauge UNF, 1 1/4 x 12 ANSI B1.1 / 2B, M315.932.F) and note the inspection result alongside lot or batch data to preserve traceability in quality records. Metav IndustryLine: Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
1 1/4" UNC Thread Plug Gauge 7 TPI, ANSI B1.1/B1.2 Hardened Gauge Steel 2B - Metav IndustryLine
Take advantage of a hardened gauge-steel design and strict ANSI/ASME conformity to speed up thread inspection and reduce rework. Choose a certified thread plug gauge for reliable internal-thread acceptance testing and order directly via Metav Werkzeuge or consult our experts for specification support. Thread plug gauge UNC 1 1/4" × 7 TPI — hardened gauge steel (ANSI/ASME B1.1) The thread plug gauge UNC 1 1/4" × 7 TPI (2B) verifies internal UNC threads to ANSI/ASME B1.1 tolerances for consistent production acceptance and incoming inspection. Hardened gauge steel construction ANSI/ASME B1.1/B1.2 compliant Tolerance class 2B for internal threads Suitable for repeatable inspection tasks Ensure production conformity with a standardised UNC check The thread plug gauge UNC 1 1/4" × 7 TPI (2B) is designed to provide a simple, repeatable pass/fail check for internal UNC threads produced to ANSI/ASME B1.1. Using a purpose-made plug eliminates subjective assessment during assembly or quality control, thereby reducing rework and preventing faulty components from entering the next production stage. The specified 2B tolerance denotes the standard internal-thread fit commonly required in mechanical assemblies, so the gauge supports traceable verification against widely accepted industrial norms. Robust materials that keep inspection precise over time Manufactured from hardened gauge steel, the gauge resists wear and preserves the reference form of the thread flanks under repetitive use. That material choice maintains measurement integrity across long inspection runs and lowers lifetime cost by extending service intervals. The compact mass and balanced geometry make handling straightforward during routine checks in the workshop or inspection room, while the clear marking of size and pitch simplifies inventory control and quick identification during process audits. Integrate a fast go/no-go routine into quality workflows A thread plug gauge streamlines in-process and incoming inspections by offering immediate go/no-go decisions without specialised metrology equipment. The tool suits machine shops, assembly lines and quality departments where time-efficient verification is crucial; adopting standardised gauges supports consistent results and simplifies operator training. Documented identifiers such as SKU and GTIN ensure each gauge can be recorded in quality logs and inventory systems for traceability and audit purposes. For certified-thread inspection tools and technical advice contact Metav Werkzeuge in Emmerich: +49 2822 7131930 or info@metav-werkzeuge.com Technical data Article number: M315.932 GTIN: 4054469179834 Designation: Thread plug gauge UNC 1 1/4" × 7 ANSI/ASME B1.1 / 2B Measurements & core data Size: 1 1/4" Pitch: 7 TPI Tolerance class: 2B Weight: 0.6 kg Tariff number: 90173000 Features & standards Material: hardened gauge steel Standard: ANSI/ASME B1.1/B1.2 Category: Gauges — thread plug gauge Intended use: internal thread verification FAQ What thread specification does this gauge check? The gauge checks UNC 1 1/4" × 7 TPI threads to ANSI/ASME B1.1 and is supplied as a tolerance class 2B plug for internal-thread acceptance (SKU M315.932). Is this thread plug gauge suitable for production inspection? Yes — the hardened construction and standardised dimensions of this thread plug gauge make it suitable for repetitive go/no-go checks in machine shops and quality departments where reliable, fast verification is required. How is the gauge identified and tracked? Identification is possible via SKU M315.932 and GTIN 4054469179834, which supports traceability in inventory systems and quality records for audits. What does tolerance class 2B mean for internal threads? Tolerance class 2B specifies the standard internal-thread fit for UNC threads, providing the common balance between easy assembly and acceptable clearance used in general engineering applications. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
1 1/4" UNC Thread Plug Gauge Go 1.1/4 x 7 TPI ANSI B1.1 / 2A - Metav IndustryLine
Take advantage of the combination of precision acceptance checks, hardened gauge steel and full ANSI compliance for reliable, repeatable thread inspection. Order the gauge directly via Metav Werkzeuge or consult our specialists for application advice. Thread Ring Gauge UNC GO, 1 1/4" x 7 – ANSI B1.1, 2A by Metav IndustryLine A Thread Ring Gauge UNC GO, 1 1/4" x 7 designed for fast verification of external UNC threads to the ANSI/ASME B1.1 standard Hardened gauge steel construction ANSI B1.1 / B1.2 compliant GO ring for UNC 1 1/4" x 7 thread Tolerance class 2A for external threads Reduce inspection time with a one-step GO acceptance check The GO ring purpose is straightforward: permit only threads that meet dimensional acceptance into production. By using a dedicated GO ring, tolerance evaluation turns into a quick pass/fail operation, improving throughput in assembly and incoming inspection. The gauge cuts decision time on the shop floor, supplies reproducible results and minimises subjective judgement during thread acceptance, which is essential in high-volume or repetitive inspection tasks. Built for longevity and repeatable performance Constructed from hardened gauge steel, this ring gauge resists wear and maintains its form under frequent use. Heat treatment and precision finishing reduce the need for frequent replacement, supporting continuous production runs and lowering long-term tooling costs. The rugged material and careful manufacturing ensure that the gauge preserves its acceptance limits over many inspection cycles, so measurement integrity remains consistent across batches. Conformance and traceability to support quality systems Manufactured to ANSI/ASME B1.1/B1.2 and supplied as a GO gauge in tolerance class 2A, the product aligns with common engineering specifications for UNC threads. The clear specification facilitates documentation in quality records and supports traceability within audit trails. For organisations that rely on documented evidence of correct inspection methods, the gauge integrates simply into existing quality workflows and inspection plans. Contact Metav Werkzeuge for tailored advice on integrating this GO ring gauge into production and to secure the correct gauge for reliable thread inspection. Technical data Article number: M315.962 GTIN: 4054469180472 Label: Gewinde-Lehrring UNC GO, 1.1/4 x 7 ANSI B1.1 / 2A Facts Mass: 0.7 kg Thread pitch: 7 tpi Tariff number: 90173000 Special features Material: hardened gauge steel Standard: ANSI/ASME B1.1/B1.2 Type: GO thread ring gauge Tolerance class: 2A Category: Gauges / Inspection tools FAQ What is the intended use of this GO ring gauge? The GO ring gauge is intended for rapid acceptance testing of external UNC threads; the Thread Ring Gauge UNC GO, 1 1/4" x 7 checks whether threads meet the acceptance limits for assembly. Does this gauge comply with recognised standards? Yes, the gauge is manufactured to ANSI/ASME B1.1/B1.2 and supplied as a GO gauge in tolerance class 2A to support standardised inspections. What material is the ring gauge made from? The thread ring is made from hardened gauge steel, giving the Thread Ring Gauge UNC GO, 1 1/4" x 7 good wear resistance and stable dimensional performance. How is the pitch specified for this tool? The tool is specified with a pitch of 7 threads per inch, matching the UNC 1 1/4" × 7 designation used for the gauge. Is this ring suitable for routine shop-floor inspection? Yes, the GO ring gauge is designed for routine acceptance checks and offers fast pass/fail results suitable for shop-floor use and incoming inspections. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
1 1/4" UNEF Thread Go Ring 18 TPI Right-Hand Hardened Gauge Steel ANSI B1.1/2A - Metav IndustryLine
Take advantage of a hardened gauge steel construction combined with strict ANSI/ASME B1.1 conformity and a precise 2A tolerance for reliable thread verification. Order the ring gauge directly via Metav Werkzeuge or consult the technical team for application advice. Gewinde-Lehrring UNEF GO, 1 1/4 x 18 (ANSI/ASME B1.1) — Ring gauge, right-hand thread A Gewinde-Lehrring UNEF GO, 1 1/4 x 18 ANSI B1.1 / 2A is a go ring gauge designed for fast verification of external UNEF threads in production and inspection environments. ANSI/ASME B1.1/B1.2 compliant go gauge UNEF 1 1/4 in, 18 tpi verification Hardened gauge steel for longevity Right-hand thread, tolerance class 2A Ensure thread conformity with recognised standards The go ring gauge provides an immediate go/no-go check against the ANSI/ASME B1.1 UNEF profile so that production batches meet specified thread form and pitch. As a GO gauge, it confirms whether an external thread falls within the allowable maximum material limit for assembly; acceptance is rapid and unambiguous, reducing downstream rework. The instrument’s compliance with the referenced standard offers a clear audit trail for quality control and supports consistent process decisions on the shop floor. Durable construction for repeated inspection cycles Manufactured from hardened gauge steel, the ring is engineered for wear resistance and dimensional stability under frequent use. The robust material means fewer replacements and predictable performance over time, which improves inspection throughput and lowers total cost of ownership. The compact mass of approximately 0.7 kg and stout form factor aid handling and reduce operator fatigue during repeated checks, making it well suited to continuous production or incoming inspection stations. Accurate verification of 1 1/4 in UNEF threads Designed for 1 1/4 in nominal threads at 18 tpi, the gauge verifies thread form, major diameter fit and pitch consistency in one simple operation. The marked tolerance class 2A corresponds to common external thread limits and provides a reliable acceptance criterion for mating parts. This gauge thus streamlines quality decisions: parts that pass the GO test proceed to assembly, while failures are flagged for rework or sorting, saving time and preventing costly assembly errors. Practical benefits for workshop and quality teams The ring’s right-hand configuration and unambiguous pass/fail functionality shorten inspection cycles and simplify operator training. Its rigid construction keeps runout and distortion low, supporting repeatable results across many cycles. Supplied as a dedicated verification tool for UNEF threads, it fits inspection benches and gauges sets used in mechanical engineering, maintenance departments and goods-receipt inspections, helping teams maintain steady production quality with minimal overhead. Contact Metav Werkzeuge for tailored advice on thread inspection and secure immediate access to the ANSI/ASME‑compliant ring gauge M315.962.EF from stock in Emmerich. Technical data Article number: M315.962.EF GTIN: 4054469180489 Label: Gewinde-Lehrring UNEF GO , 1.1/4 x 18 ANSI B1.1 / 2A Material: hardened gauge steel Standard: ANSI/ASME B1.1/B1.2 Core specifications Nominal size: 1 1/4 in Threads per inch: 18 tpi Weight: 0.7 kg Tolerance class: 2A Special features Go ring gauge for UNEF thread series Right-hand thread Designed for external thread verification SKU: M315.962.EF FAQ What is this gauge used for? This ring gauge is used as a GO gauge to verify external UNEF 1 1/4 in × 18 tpi threads and to ensure conformity with the ANSI/ASME B1.1 profile. Which thread tolerance does the gauge check? The instrument checks external threads to tolerance class 2A, which is a standard external thread limit for many mechanical applications. Is the gauge suitable for production inspection? Yes, the hardened construction and clear GO functionality make the ring suitable for repetitive production or incoming inspection use with consistent pass/fail assessment. Can this ring gauge be used for left-hand threads? No, this specific gauge is manufactured as a right-hand thread verification tool and is not suitable for left-hand threads. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
1 1/4" UNEF Thread Go/No-Go Plug Gauge 18 TPI Right-Hand, ANSI B1.1 / 2B - Metav IndustryLine
Precision verification of UNEF internal threads is achieved through hardened gauge steel construction and compliance with ANSI/ASME B1.1/B1.2; the plug gauge provides reproducible checks to tolerance class 2B. Order the gauge directly via Metav Werkzeuge or contact our consultants for application advice. Gewinde‑Lehrdorn UNEF, 1.1/4 x 18 ANSI B1.1 / 2B — Metav IndustryLine plug gauge, right‑hand thread Gewinde‑Lehrdorn UNEF, 1.1/4 x 18 ANSI B1.1 / 2B is a right‑hand thread plug gauge designed to verify internal UNEF threads to industry standards in production and inspection environments Hardened gauge steel construction Conforms to ANSI/ASME B1.1/B1.2 standards UNEF 1¼″ × 18 TPI, tolerance class 2B Right‑hand thread for internal inspection Standards‑based inspection for consistent acceptance decisions The plug gauge verifies internal UNEF threads to the ANSI/ASME B1.1/B1.2 standard, offering a clear go/no‑go criterion for tolerance class 2B checks. Built from hardened gauge steel, the tool resists wear during repeated use, which preserves dimensional integrity and reduces measurement drift in series production. Using a dedicated plug gauge simplifies conformity checks compared with comparative or subjective methods, providing a quantifiable basis for acceptance that supports quality control procedures and audit trails. Robust design for repetitive workshop use Designed as a compact and durable inspection tool, the gauge combines a precise thread form with a wear‑resistant material to maintain repeatability in daily use. The UNEF 1 1/4" × 18 TPI geometry suits fine‑pitch applications where thread fit and engagement are critical; tolerance class 2B is the standard internal fit for many engineering assemblies. The right‑hand configuration matches conventional threaded parts, while the hardened construction reduces risk of nicks and deformation, helping to ensure that routine inspections remain reliable over long production runs. Clear provenance and procurement advantages Each item is supplied with traceable identification suitable for controlled procurement: a manufacturer SKU and GTIN are provided so the gauge can be logged into stores and calibration systems. Sourcing through Metav IndustryLine delivers the advantage of a European distribution and stock hub in Emmerich, combining broad product range with industrial quality assurance. For workshop managers, the combination of standard conformity, durable construction and clear labelling simplifies logistics and helps integrate the gauge into incoming inspection or final acceptance processes. For reliable UNEF thread control, request the Metav IndustryLine plug gauge from Metav Werkzeuge in Emmerich or consult our specialists to confirm the correct gauge for the application Technical Data Article number / SKU: M315.932.EF GTIN: 4054469179841 Description: Gewinde‑Lehrdorn UNEF, 1.1/4 x 18 ANSI B1.1 / 2B Manufacturer: Metav IndustryLine Facts Size: 1 1/4" (1.25 inches) Pitch: 18 TPI Weight: 0.6 kg Tolerance class: 2B Tariff number: 90173000 Special features Material: gauge steel, hardened Thread type: UNEF (Unified National Extra Fine) Standard: ANSI/ASME B1.1/B1.2 Thread direction: right‑hand FAQ What standard does this plug gauge conform to? The Gewinde‑Lehrdorn UNEF 1.1/4 x 18 (Metav IndustryLine plug gauge, SKU M315.932.EF) is manufactured to ANSI/ASME B1.1/B1.2 for UNEF thread checks. Which thread size and pitch are inspected with this gauge? This plug gauge verifies UNEF 1 1/4" × 18 TPI internal threads and is intended for tolerance class 2B inspections. Is the gauge suitable for repetitive workshop use? Yes, the Metav IndustryLine plug gauge is made from hardened gauge steel to withstand repeated inspections while maintaining dimensional stability. Can this gauge be used for external thread checks? No, a plug gauge such as the Gewinde‑Lehrdorn is designed specifically for internal thread verification; external threads require a corresponding ring or screw gauge. How is the product identified for procurement and stock control? The gauge is supplied with SKU M315.932.EF and GTIN 4054469179841, facilitating traceability in stores and inventory systems. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
1 1/4" UNEF Thread Go/No-Go Ring 18 TPI Right-Hand Hardened Gauge Steel ANSI B1.1/B1.2 - Metav IndustryLine
Take advantage of precise thread acceptance control with a hardened gauge steel construction and ANSI/ASME B1.1 compliance to safeguard production quality; order this NOGO ring directly via Metav Werkzeuge or consult our specialists for fitment advice. Thread ring gauge UNEF NOGO, 1 1/4 x 18 (2A) — NOGO thread ring gauge, hardened gauge steel, Metav IndustryLine Thread ring gauge UNEF NOGO, 1 1/4 x 18 (2A) for verification of external UNEF threads in production and incoming‑inspection environments NOGO type for thread conformity control Hardened gauge steel construction ANSI/ASME B1.1 compliant Right‑hand UNEF 1 1/4‑18 2A Reliable pass/fail control that prevents false acceptance The NOGO design provides an unambiguous go/no‑go decision that reduces downstream rework and rejects before assembly. Made from hardened gauge steel, the ring resists wear and maintains form stability under repetitive use, which delivers consistent verification of external threads. Integration into routine inspection prevents incorrect fittings and supports traceable quality checks. Built to meet industry standards for interchangeability Manufactured to ANSI/ASME B1.1/B1.2, the gauge is suited for environments where adherence to thread standards is mandatory. The 2A tolerance class ensures the tool corresponds to the established external thread limits for UNEF series, making it appropriate for serial production checks and supplier inspections where standard conformity is required. Designed for practical workshop and production workflows Lightweight yet robust, the ring simplifies shop‑floor handling and fastens rapid inspection cycles without specialised fixtures. The right‑hand UNEF specification and 18 tpi pitch match common US fine‑thread applications, enabling straightforward verification of threaded shafts and studs. The clear pass/fail function reduces operator uncertainty and speeds up quality processes. Long‑term value through durability and traceability The hardened material and precise manufacturing maintain gauge integrity over many inspection cycles, thereby lowering lifecycle costs when compared with softer tools. The ring supports consistent tolerance control in component production and incoming inspection, contributing to reproducible assembly quality and fewer warranty issues. For stock enquiries or to discuss suitability for specific thread forms, contact Metav Werkzeuge for expert guidance and availability of the Metav IndustryLine NOGO thread ring gauge. Technical data SKU: M315.992.EF GTIN: 4054469181127 Manufacturer: Metav IndustryLine Facts Size: 1 1/4" Pitch: 18 tpi Weight: 0.6 kg Special features NOGO type thread ring Material: hardened gauge steel Standard: ANSI/ASME B1.1/B1.2 Tolerance class: 2A Thread direction: right‑hand Description: thread ring gauge for UNEF external threads FAQ Is this gauge suitable for checking external UNEF threads? Yes. The Thread ring gauge UNEF NOGO, 1 1/4 x 18 (2A) is specifically designed for verification of external UNEF threads to the ANSI/ASME B1.1 standard. What does the NOGO designation mean in practice? NOGO indicates the ring must not pass over an externally threaded part; if it does, the thread is out of tolerance. The Metav IndustryLine NOGO ring provides a clear fail criterion for quality control. Which tolerance class does the ring represent? The gauge is made to 2A tolerance class for external threads, corresponding to the nominated limits for a standard UNEF external thread. Can this ring be used for left‑hand threads? No. This specific ring is manufactured for right‑hand UNEF threads; left‑hand threads require a dedicated gauge. What identifying code should be referenced when ordering? Refer to SKU M315.992.EF and the size designation UNEF 1 1/4‑18 when checking stock or placing an enquiry. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
Fast, tactile checks where electronics are impractical
Gauges and test pins provide unequivocal go/no-go results for threads, bores, gaps and radii without relying on electronics. The range covers plug gauges and ring gauges for internal and external threads, feeler gauges and precision feeler strips for micro‑gap assessment, plus probe pins and measuring pins for tactile diameter and pitch checks.
How these tools work in the production environment
Mechanical gauges operate as direct reference standards: a plug gauge or ring gauge verifies conformity to thread profiles and mating ability, while limit gauges separate accept from reject in a single step. Test pins are used to tactilely measure small bore diameters, centre‑to‑centre distances and radii. Manufactured from hardened gauge steel or ceramic and often precision lapped, these instruments deliver immediate physical results that are ideal for incoming inspection, machine‑side checks and final control.
Measurable benefits that affect production performance
- Reduced scrap and rework through rapid, unambiguous pass/fail assessment.
- Increased repeatability thanks to very low measurement uncertainty and fine lapping.
- Lower downtime: quick checks at the machine save cycle time and reduce setup periods.
- Durable construction with high wear resistance from specialised, low‑distortion alloys.
- Versatile delivery formats: individual gauges, organised sets in wooden cases or metre‑length feeler rolls compliant with DIN 2269.
Why Metav is the practical choice for precision supplies
Metav combines decades of expertise with a broad warehouse and quality filtering from Emmerich. As a precision partner for industry, craft and trade, Metav supplies a comprehensive selection of gauges and test pins alongside complementary tools such as precision calipers and setting rings. With over 48,000 customers and a catalogue exceeding 250,000 items, Metav is positioned to supply reliably, reduce vendor complexity and support traceable quality control to national standards.
Summary
Gauges and test pins are indispensable for dependable, repeatable quality assurance where tactile, mechanical verification is preferred. Choose these plug gauges, ring gauges, feeler strips and probe pins when immediate, robust measurement decisions are required on the shop floor.
FAQ
What materials are gauges and test pins typically made from?
Gauges and test pins are usually manufactured from hardened gauge steel for durability and wear resistance; ceramic variants are available where thermal stability and minimal wear are critical.
How do thread gauges ensure mating capability?
Thread plug gauges and ring gauges check flank diameters and thread form against standards, providing a clear go/no‑go verdict that confirms pairability with mating parts.
Which tolerance class should I choose for probe pins and gauge sets?
Select tolerance classes aligned with your inspection requirements; for high‑precision tasks, sets produced to DIN 2269 or equivalent tolerance classes ensure micrometre‑level control and repeatability.
Can feeler gauges measure contact gaps in valve and engine work reliably?
Yes. Feeler gauges and precision feeler strips, supplied either as a fan or metre‑length rolls, allow accurate assessment of valve clearances and contact gaps down to micrometre increments.
How do limit gauges speed up in‑process inspection?
Limit gauges separate good from bad in a single, tactile operation, enabling rapid go/no‑go checks at the machine and reducing both inspection time and the likelihood of human interpretation errors.
Fragen zu diesen Produkten??
Mit mehr als 30 Jahren Erfahrung beraten wir Sie gerne persönlich.
Tel.: +49 2822 7131930
Mail: info@metav-werkzeuge.com