Precision gauge blocks and plug gauges for reliable dimensional control
Mechanical gauge blocks and plug gauges are essential for tactile verification of threads, bores and gap dimensions, providing fast, unambiguous go/no-go results that enhance process reliability and reduce scrap. Designed for industrial metalworking and toolmaking, these precision tools support incoming inspection and final quality checks by delivering traceable measurements in applications such as thread inspection, bore diameter testing and spacing checks. Manufactured from specially hardened, low-distortion alloys and fine-lapped for minimal measurement uncertainty, the range includes thread plug gauges, precision plug gauges and calibration gauge blocks to ensure long-term repeatability and wear resistance.
17.1mm Gauge Pin 50mm Length Workshop Version - Metav IndustryLine
Take advantage of precise gauge control and robust workshop construction to reduce setup time and rework. The combination of ±0.002 mm tolerance, a 17.1 mm diameter and a 50 mm length delivers consistent mating and repeatable end‑measure checks; order via Metav Werkzeuge or consult the technical team for application advice. Gauge pin M323.H10 — 17.1 mm diameter, 50 mm length (Metav IndustryLine) The Gauge pin M323.H10 is a single precision test pin designed for fixture setting, end‑measure verification and gaging applications in workshop environments Single precision gauge pin 17.10 mm Hardened special steel construction Length 50 mm for fixture and end‑measure Supplied in transport case Precision that reduces rework and downtime A tight tolerance of ±0.002 mm ensures that mating fits and inspection references are reliable, which cuts down on part rejection and repeat measurements. The combination of a 17.1 mm diameter and 50 mm overall length provides a stable reference for end‑measure checks and datum setting. As a result, measurement intervals and fixture adjustments become predictable and reproducible, improving throughput in batch runs and quality control routines. Robust design for everyday workshop use Manufactured from special steel, the pin is specified for regular handling and exposure to workshop conditions. The workshop version construction prioritises wear resistance and dimensional stability so that surface and edge integrity remain intact over repeated seating cycles. This reduces the frequency of replacements and helps to maintain consistent gauge behaviour during production and assembly tasks. Practical handling and faster process integration Delivered as a single, ready‑to‑use gauge pin, this item integrates directly into jigs, go/no‑go fixtures and inspection benches. The 50 mm length offers clearance for clamps and supports while maintaining rigidity during measurement. Supplied in a transport case, the pin is protected during storage and movement between workstations, enabling simple, damage‑free deployment across multiple lines or workcells. Clear identification and workshop reliability The M323.H10 is intended as a straightforward, repeatable reference element for end‑measure and gaging tasks. Labelling and identifiers ensure traceability during stock management and toolroom allocation. Backed by a European supply chain filter, the Metav IndustryLine variant stands for accessible precision that fits routine industrial and maintenance workflows without bespoke procurement processes. Contact Metav Werkzeuge for technical advice on integrating the Metav IndustryLine gauge pin into existing fixtures or to request a suitability assessment for specific gaging tasks Technical Data SKU: M323.H10 GTIN: 4061905070693 Brand: Metav IndustryLine Facts Diameter: 17.1 mm Length: 50 mm Tolerance: ±0.002 mm Weight: 0.15 kg Special features Material: Special steel Workshop version Single piece delivery Supplied in transport case Category: Gauge pins (Messstifte) FAQ What tolerance can be expected from this gauge pin? The gauge pin M323.H10 is specified with a tolerance of ±0.002 mm, making it suitable for high‑precision end‑measure checks and fixture references. What material is used for the pin? The pin is made from special steel, selected for wear resistance and dimensional stability in workshop conditions. Which applications suit this test pin best? Typical uses include fixture setting, end‑measure verification, jigs and assembly alignment; the pin functions as a stable reference in gaging and go/no‑go checks. How is the product supplied and protected? The M323.H10 is supplied as a single item and comes in a transport case to protect the gauge during storage and transit. Which identifiers are useful when ordering or restocking? Order or reference the SKU M323.H10 and GTIN 4061905070693 for unambiguous procurement and stock control. Metav IndustryLine: Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
17.21mm Gauge Pin, Single, 50mm Length, Workshop Version - Metav IndustryLine
The combination of a precise 17.21 mm nominal diameter, a compact 50 mm length and a tight ±0.002 mm tolerance ensures reproducible end‑dimension checks and robust fit gauging in workshop environments; benefit from the durability of special steel and the convenience of individual supply. Order the gauge pin directly via Metav Werkzeuge or ask our consultants for application advice. Gauge pin M323.H21 — 17.21 mm diameter, 50 mm length (Metav IndustryLine) A gauge pin, single, 17.21 mm, 50 mm length designed for reliable end‑dimension inspection and fit testing in toolrooms and quality control stations. Single gauge pin 17.21 mm diameter 50 mm compact length for stable handling Tolerance ±0.002 mm for high precision Supplied individually for controlled inspection Precise inspection where repeatability matters This inspection pin delivers a defined 17.21 mm diameter with a tight ±0.002 mm tolerance, making it suitable for end‑dimension verification and go/no‑go fit checks. The narrow tolerance supports consistent interchangeability across batches and reduces rework by providing an objective reference for gauge blocks, bores and mating parts. The M323.H21 designation identifies the item for inventory and traceability while the compact length maintains handling stability during repetitive checks. Durable construction for workshop use Manufactured in special steel, the pin is engineered to resist wear in everyday use and to retain dimensional integrity over time. The 50 mm length provides sufficient engagement for short bores and shoulder checks while remaining easy to manoeuvre in tight setups. The workshop design emphasises practical robustness: the component is delivered singly to simplify storage and to avoid cross‑contamination between different nominal sizes, supporting orderly inspection routines in production environments. Practical integration and quality assurance As an individual inspection element, this gauge pin fits seamlessly into existing test benches, fixtures and gauge sets. The item's compact mass and measured weight aid rapid placement and removal during sampling inspections, promoting efficient measurement cycles. Clear identification via M323.H21 and the GTIN enables straightforward stock control and documentation in quality workflows, assisting audits and traceability without additional conversion or adaptation. Choose Metav IndustryLine's M323.H21 gauge pin for dependable, workshop‑ready inspection performance and contact Metav Werkzeuge for tailored advice or order coordination. Technical data Article number: M323.H21 GTIN: 4061905071492 Category: Messstifte Facts Nominal diameter: 17.21 mm Overall length: 50 mm Tolerance: ±0.002 mm Weight: 0.15 kg Special features Material: special steel Design: workshop execution Supply: single unit ECLASS: 21170231 FAQ What tolerance does this gauge pin offer? The gauge pin is specified with a tolerance of ±0.002 mm, making the M323.H21 suitable for high‑precision end‑dimension checks. Which material is used for the pin? The pin is made from special steel, chosen for durability and stable dimensional performance under regular workshop conditions. How is the product supplied and identified? The item is supplied individually and identified as M323.H21 (GTIN 4061905071492) to simplify stock management and traceability. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
17.22mm Gauge Pin 50mm Length Workshop Version, ±0.002mm Accuracy - Metav IndustryLine
The single Metav IndustryLine gauge pin M323.H22 delivers repeatable end‑measure checks thanks to a tight ±0.002 mm tolerance, a nominal diameter of 17.22 mm and a robust 50 mm length; combine accuracy, durability and straightforward logistics by ordering through Metav Werkzeuge or contacting our specialists for specification advice. Metav IndustryLine gauge pin M323.H22 — gauge pin, 17.22 mm, 50 mm length The Metav IndustryLine gauge pin M323.H22 is a single test pin designed for precise end‑measure inspections in workshop and production environments. Diameter 17.22 mm nominal Tolerance ±0.002 mm high precision 50 mm length for end‑measure checks Manufactured from special steel Faster, verifiable inspections with industrial accuracy The M323.H22 functions as a reference element for end‑measure tasks where consistency and traceability matter. With a declared tolerance of ±0.002 mm, the pin reduces measurement uncertainty and shortens inspection cycles by providing a stable reference diameter. In practice, this degree of precision supports quality control decisions without repeated reworking; the hardened geometry and tight manufacture tolerances ensure each check is comparable and repeatable across shifts and operators. Robust construction that withstands workshop use Constructed from special steel, the pin resists wear and maintains form under repetitive seating and extraction operations. The 50 mm shank length gives good handling and engagement in fixtures while keeping bulk low for compact setups. The workshop specification means the component is produced for everyday industrial use rather than delicate lab handling, so maintenance intervals are minimised and service life is extended — a cost‑effective choice when throughput and uptime are priorities. Application scope and metrological classification This gauge pin sits in the micro class of measuring tools (nominal range around 10–100 mm), making it suited to fine mechanical assemblies, jig and fixture checks, and end‑dimension verification on turned or milled parts. The pin serves as a straightforward master for go/no‑go checks, plug gauges and manual comparators. For users familiar with tolerance bands, the combination of 17.22 mm nominal size and ±0.002 mm tolerance offers a precise control point for batch acceptance or for setting up more complex measurement chains. For dependable end‑measure control, place an order for the Metav IndustryLine gauge pin M323.H22 via Metav Werkzeuge or request tailored advice from our specialists at info@metav-werkzeuge.com or +49 2822 7131930 Technical Data Article number: M323.H22 GTIN: 4061905071508 Brand: Metav IndustryLine Category: Gauge pin / test pin Facts Nominal diameter: 17.22 mm Length: 50 mm Manufacturer SKU: M323.H22 Weight: 0.15 kg Tolerance: ±0.002 mm Special features Material: special steel Workshop version Single gauge pin, individual supply Intended use: end‑measure inspections FAQ What level of precision does this gauge pin provide? The Metav IndustryLine gauge pin M323.H22 is manufactured to a tolerance of ±0.002 mm, making it suitable where tight dimensional control is required. For which applications is the gauge pin best suited? The pin is intended for end‑measure checks, fixture verification and as a reference for plug or comparator gauges in workshop and production settings. What material is the pin made from and why does it matter? The pin is made from special steel, chosen for its wear resistance and geometric stability during repeated seating and extraction cycles. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
17.23mm Gauge Pin Length 50mm Workshop Version - Metav IndustryLine
Take advantage of the combination of workshop-ready robustness, 17.23 mm gauge accuracy and fine ±0.002 mm tolerance for reliable end-dimension checks; order the test pin directly via Metav Werkzeuge or consult our specialists for application advice. Test Pin M323.H23 — Single Test Pin, 17.23 mm Gauge Diameter, 50 mm Length (Metav IndustryLine) Test Pin M323.H23 is a workshop-grade, precision test pin intended for end-dimension inspection and gauge setting in small-part environments Workshop version, robust design Diameter 17.23 mm for end‑dimension checks Length 50 mm for stable handling Accuracy ±0.002 mm tolerance Reliable measurements that speed up inspection cycles The compact test pin is engineered to deliver consistent results in routine checks and repeat measurements. With a nominal gauge size of 17.23 mm and a verified displacement tolerance of ±0.002 mm, the pin provides the dimensional certainty required for serial inspection tasks and Go/No‑Go checks. The tight tolerance reduces rework and downstream rejects by ensuring that measured end dimensions meet specification limits quickly. As a workshop component, this measuring element supports predictable throughput and simplifies traceable inspection steps. Designed for secure handling and precise positioning A 50 mm overall length gives the pin a practical grip and sufficient support when used with holders, fixtures or manual gauges; the length balances reach and stiffness so alignment is straightforward and repeatable. Manufactured from special steel, the pin offers durable contact surfaces under frequent use and maintains geometric stability during short transfer and measurement operations. The workshop execution focuses on functional resilience rather than laboratory fragility, making the element suited to tasks ranging from fixture verification to component release testing. Small-format classification and logistics fit for busy shops With its small gauge size the product falls into the micro measurement class, making it particularly suitable for fine mechanical and precision small-part work where compact tools are required. Delivery includes a transport case, ensuring the pin remains protected in transit and between jobs, which aids organisation on busy benches. The item is traceable by GTIN and SKU for inventory control and can be integrated into existing inspection kits or gauge sets without complication. The combination of compact form, documented accuracy and practical packaging supports a dependable routine inspection workflow. Contact Metav Werkzeuge for tailored application advice or to request the workshop-ready Test Pin M323.H23 — specialists are available to recommend fixtures, complementary gauges or stock options and to advise on immediate availability from Emmerich Technical data Article number: M323.H23 GTIN: 4061905071515 Label: Prüfstift, einzeln, 17,23 mm Länge 50 mm ECLASS: 21170231 Facts Gauge diameter: 17.23 mm Length: 50 mm Accuracy / deviation: ±0.002 mm Weight: 0.15 kg Special features Material: special steel Workshop execution Supplied in transport case Category: Test pins FAQ What inspection tasks is this test pin suited for? The test pin M323.H23 (Metav IndustryLine test pin, SKU M323.H23) is suited for end‑dimension checks, gauge setting and fixture verification on small components where a 17.23 mm reference is required. Does the test pin come ready for use out of the box? The workshop version of the test pin arrives protected in a transport case and is immediately usable for workshop inspection; no additional preparation is necessary beyond standard cleaning and mounting. Which materials is the pin manufactured from and how does that affect wear? Manufactured from special steel, the M323.H23 test pin provides robust contact faces for frequent use in workshop environments and retains geometric stability under normal handling. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
17.24mm Gauge Pin Workshop Version 50mm Length, Special Steel ±0.002 - Metav IndustryLine
Take advantage of a compact measuring solution that combines exacting dimensional control, a sturdy workshop-grade design and clear traceability for routine inspection tasks; the 17.24 mm diameter and 50 mm length deliver reliable end-measure checks with a manufacturing tolerance of ±0.002 mm. Order the gauge pin directly via Metav Werkzeuge or ask our consultants if needed. Gauge pin, single — 17.24 mm Ø, 50 mm length (Metav IndustryLine) The gauge pin, single — 17.24 mm Ø, 50 mm length is a workshop-grade precision test pin designed for end measurements and go/no-go checks on small bores and fittings. Precision Ø 17.24 mm, tolerance ±0.002 mm 50 mm length for end-dimension checks Workshop-grade special steel construction Supplied as a single inspection pin Compact precision for fine assemblies This compact test element belongs to the micro measurement class and is sized to deliver repeatable checks where space is limited. With a nominal diameter of Ø 17.24 mm and a length of 50 mm, the component provides a stable contact area for end-measurement tasks and fit verification. The specified tolerance of ±0.002 mm ensures that dimensional deviations remain within tight limits, supporting consistent pass/fail decisions during production control or incoming inspection. The design reduces measurement uncertainty in small cavities and mating parts, making it suitable for precision fixtures and manual inspection routines. Robust workshop design built for everyday use Produced in a workshop-grade finish and made from special steel, this single test pin offers the mechanical resilience required in daily metrology tasks. The material choice balances hardness and corrosion resistance to maintain geometry under repeated handling and insertion cycles. The compact mass and form factor enable fast positioning in jigs and test rigs while preserving concentricity and contact quality. This durability translates into longer intervals between replacements and dependable performance on the shop floor, reducing downtime for routine quality checks. Simple integration into inspection workflows The test pin is supplied as an individual measuring element and integrates seamlessly into gauge blocks, plug gauges and custom fixtures. Identified by SKU M323.H24, the part is easy to catalogue and reference in inspection plans or assembly instructions. The consistent manufacturing tolerance supports traceable sampling and statistical process control, improving the reliability of dimensional reports. For operations seeking a low-complexity precision aid, this single gauge pin provides a straightforward solution for repeatable end-measurement and go/no-go applications while fitting into established workshop routines. Choose the Metav IndustryLine gauge pin for reliable micro-range checks — contact Metav Werkzeuge in Emmerich for technical advice at info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: M323.H24 GTIN: 4061905072017 Material: Special steel Weight: 0.15 kg Length: 50 mm Facts Diameter: 17.24 mm Tolerance: ±0.002 mm Measurement range: 17.24 mm Mass: 0.15 kg Special features Workshop version Single test pin supply Category: Gauge pin / end gauge Precision-class suitable for micro-range inspections FAQ What are the main dimensions of this test pin? The gauge pin M323.H24 has a diameter of 17.24 mm and an overall length of 50 mm. What tolerance is achieved during manufacture? Manufacturing tolerance is ±0.002 mm, providing tight dimensional control for inspection tasks. What material is used for the pin? The pin is made from special steel in a workshop-grade finish for durable handling. For which applications is this pin intended? The single test pin is intended for end-dimension checks, small-bore verification and go/no-go inspections in micro-range assemblies. How is the item supplied for inventory and referencing? The part is supplied as a single inspection pin and identified as SKU M323.H24 for straightforward catalogue management. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
17.25mm Gauge Pin, Single, 50mm Length, Workshop Version - Metav IndustryLine
Reliable dimensional control for workshop inspection: benefit from ±0.002 mm measurement precision and a robust special steel construction in a compact 50 mm length; order the part directly via Metav Werkzeuge or consult the sales team for batch supply and suitability. Gauge pin, single, 17.25 mm, length 50 mm — Metav IndustryLine, ±0.002 mm tolerance The gauge pin, single, 17.25 mm, length 50 mm is a precision end-measurement pin intended for workshop and inspection use, ideal for quick go/no-go checks and repeatable dimensional verification. 17.25 mm nominal diameter 50 mm working length Accuracy ±0.002 mm Workshop version, special steel Consistent precision that reduces inspection uncertainty For routine dimensional checks, the primary advantage is reproducible measurement. The pin’s ±0.002 mm tolerance provides a dependable reference point for pass/fail decisions and fast in-process checks. This reproducibility cuts verification time and lowers the risk of downstream rework by delivering a clear, repeatable datum. Where tight tolerances are required, using a precise reference pin avoids ambiguous readings and contributes directly to process stability and traceability. Built for workshop handling and long-term wear resistance Constructed from special steel and specified as a workshop version, the pin balances durability with handling convenience. The 50 mm working length offers enough engagement for reliable seating while remaining compact for frequent use; the moderate mass also helps with stable placement during manual checks. This robustness minimises surface wear and maintains the diameter over many cycles, which supports longer service intervals and a steady performance profile in production environments. Easy integration into inspection routines and stock management Marked with SKU M323.H25 and GTIN 4061905072024, the component slots readily into existing gauge assortments and inspection sets. The nominal 17.25 mm diameter makes it suitable as an end gauge for bore and shaft verifications or as a reference in fixture set-ups. Supplied as a single pin, it is straightforward to combine with complements for stepped checks or assemblies. Procurement through Metav IndustryLine simplifies replenishment and ensures consistent quality across batches, supporting reliable inventory control and auditing requirements. Contact Metav Werkzeuge for tailored advice on Metav IndustryLine gauge pins, batch availability, and how the M323.H25 can be integrated into existing inspection procedures — phone +49 2822 7131930 or email info@metav-werkzeuge.com Technical data Article number: M323.H25 GTIN: 4061905072024 Manufacturer: Metav IndustryLine Label: Prüfstift, einzeln, 17,25 mm Länge 50 mm Facts Nominal diameter: 17.25 mm Working length: 50 mm Tolerance: ±0.002 mm Weight: 0.15 kg Special features Material: Special steel Version: Workshop execution Category: Gauge pins Story trigger: endmasse FAQ What nominal diameter does the pin have? The gauge pin supplied as M323.H25 has a nominal diameter of 17.25 mm, suitable for precise go/no-go checks and reference measurements. What is the stated measurement tolerance? The Metav IndustryLine pin is manufactured to an accuracy of ±0.002 mm, providing high repeatability for workshop verification tasks. Which material is used for this inspection pin? The component is made from special steel, selected for wear resistance and stability under frequent handling in a workshop environment. How long is the working length and how does that help? The pin has a 50 mm working length, offering secure engagement for reliable insertion and a stable reference during manual inspections. How is the product identified for ordering and inventory? This single gauge pin is available as SKU M323.H25 and GTIN 4061905072024, which facilitates straightforward ordering and stock tracking. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
17.26mm Gauge Pin 50mm Length Workshop Finish - Metav IndustryLine
Take advantage of the combination of workshop-ready construction, ±0.002 mm dimensional accuracy and compact handling for repeatable end measurements; order directly via Metav Werkzeuge or contact our consultants for application advice. Gauge pin, single, 17.26 mm diameter · 50 mm length (Metav IndustryLine) Gauge pin, single, 17.26 mm diameter · 50 mm length is a precision inspection pin for end-measurement and go/no-go checks in fine mechanical and workshop environments. High dimensional accuracy ±0.002 mm Made from special steel, workshop version Length 50 mm for robust handling Delivered in a protective case Accuracy that secures process tolerance The pin delivers a ±0.002 mm positional tolerance, providing a reliable reference for end measurements and Go/No‑Go testing. Such tight deviation supports quality control where repeatability matters most, reducing scrap and rework. The small diameter and compact form suit high-density measurement setups, enabling consistent contact with inspection jigs and gauges while keeping setup time short and throughput steady. Robust design for daily workshop use Manufactured in special steel and specified as a workshop version, the pin balances wear resistance with practical handling. The 50 mm length gives enough purchase for manual insertion and mounting in fixtures without compromising rigidity. Supplied in a protective case, the component is ready for safe transport between benches and inspection stations, maintaining surface condition and dimensional integrity for longer service life. Practical integration into inspection routines Designed for micro-range measurements (Micro: 10–100 mm), this inspection pin suits small parts and fine mechanical assemblies where space and precision are decisive. At 0.15 kg, the item is easy to manoeuvre and mount in common test rigs. Its compact geometry simplifies alignment, so inspection cycles run faster and measurement uncertainty is minimised—supporting efficient quality assurance in both prototyping and repetitive production. For workshop-ready precision from Metav IndustryLine, contact Metav Werkzeuge for tailored advice and reliable supply from Emmerich: info@metav-werkzeuge.com or +49 2822 7131930 Technical data Article number: M323.H26 GTIN: 4061905072031 Manufacturer: Metav IndustryLine Facts Diameter: 17.26 mm Length: 50 mm Weight: 0.15 kg Tolerance: ±0.002 mm Special features Workshop version Material: special steel Delivered in protective case Category: gauge pins Suitable range: Micro (10–100 mm) FAQ How precise is this gauge pin for inspection tasks? The gauge pin from Metav IndustryLine offers a tolerance of ±0.002 mm, making this single inspection pin suitable for fine end-measurements and tight go/no‑go checks. Is the pin delivered ready for transport and storage? Yes, the single gauge pin is supplied in a protective case to preserve surface quality and ensure safe handling between inspection stations. What applications suit a 17.26 mm diameter pin? A 17.26 mm diameter inspection pin is well suited to small mechanical parts, alignment checks and fixture-based measuring tasks within the Micro (10–100 mm) measurement class. What material is used and how does it affect wear resistance? The inspection pin is made from special steel, chosen to provide robust wear resistance for regular workshop use while maintaining dimensional stability. Can this pin be used in automatic test rigs and jigs? The compact geometry and standardised diameter of the Metav IndustryLine gauge pin allow reliable integration into common fixtures and automated inspection setups. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
17.27mm Gauge Pin 50mm Length Workshop Version, Special Steel - Metav IndustryLine
Combine workshop-grade durability, ±0.002 mm repeatability and a compact 50 mm length to ensure reliable end measurements for precision inspection tasks; order the product directly via Metav Werkzeuge or ask our consultants if needed. Test pin M323.H27 – single inspection pin, Ø17.27 mm, 50 mm length (Metav IndustryLine) Test pin M323.H27 is a single inspection pin designed for precise end measurements and fixture checks in metrology applications; supplied as a workshop-grade component for machine-shop use Workshop execution, robust finishing High repeatability ±0.002 mm Special steel construction Compact Ø17.27 mm for micro applications Measurably reliable performance for routine inspection The inspection pin delivers a clear technical advantage where repeatability matters: the stated accuracy ±0.002 mm supports tight tolerance checks and consistent go/no-go assessments. Manufactured from special steel and finished for workshop use, this compact gauge component minimises runout and provides a stable contact surface for end measurements. Its 50 mm length offers a balance between stiffness and accessibility, reducing measurement variability when used in fixture checks or manual inspection stations. Compact design that suits micro measuring ranges Classified for the Micro measuring range (10–100 mm), this single pin is tailored to fine‑mechanical and small‑part quality control where handling and reproducibility are decisive. The nominal diameter Ø17.27 mm and short shank reduce leverage and bending, enabling repeatable contact with small features such as bores, pins and precision housings. As a dedicated gauge element, it integrates into pin plates, test fixtures and comparator setups, improving throughput in repetitive inspection tasks. Practical integration and workshop benefits The workshop-grade execution simplifies daily use: the geometry and material choice prioritise wear resistance under standard shop conditions and minimise downtime for replacement. Lightweight at 0.15 kg, the component is convenient to handle and store, while the clear SKU and GTIN simplify inventory control and traceability. Where consistent end measurements are required, the inspection pin provides a stable, easy-to-install option that complements existing metrology toolsets and enhances process reliability. Contact Metav Werkzeuge today to discuss how the M323.H27 inspection pin can be integrated into existing inspection fixtures or to request detailed technical data and supply options Technical data SKU: M323.H27 GTIN: 4061905072048 Material: Special steel Length: 50 mm Diameter: 17.27 mm Weight: 0.15 kg Accuracy (stated): ±0.002 mm Version: Workshop execution Facts Measuring class: Micro (10–100 mm) Product type: Single inspection/test pin Application focus: End measurements Special features Compact design for small-part inspection High repeatability for routine QC Workshop-grade finishing Story trigger: end measurements FAQ What is the declared accuracy of this inspection pin? The inspection pin M323.H27 is specified with an accuracy of ±0.002 mm, making it suitable for high‑repeatability end measurements in workshop environments. Which measuring range category does this pin belong to? This component falls into the Micro measuring range (10–100 mm), intended for fine mechanical and small‑part inspection tasks. Is the material corrosion‑resistant? The pin is made of special steel and finished for workshop use; specific corrosion‑resistant treatments are not detailed in the product data. Can this pin be used in existing test fixtures and pin plates? Yes, the M323.H27 single test pin is designed for straightforward integration in pin plates, fixtures and comparator setups where a compact Ø17.27 mm gauge element is required. What identifiers support inventory and traceability? Identification is provided via SKU M323.H27 and GTIN 4061905072048 for straightforward stock management and order processing. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
17.28mm Gauge Pin 50mm Length Workshop Finish, Special Steel - Metav IndustryLine
Take advantage of the combination of high dimensional stability, a tight tolerance of ±0.002 mm, and rugged workshop design for dependable go/no‑go and reference checks. Order the gauge pin directly via Metav Werkzeuge or consult the product specialists for application advice. Gauge pin, single — Ø 17.28 mm, length 50 mm (Metav IndustryLine) A precision gauge pin designed as a single reference mandrel for dimensional checks and jig inspection in workshop environments. Single gauge pin Ø 17.28 mm length 50 mm Workshop version with transport protection Tolerance ±0.002 mm for repeatable checks Made from high‑grade special steel Repeatable reference measurements for quality control This single gauge pin is specified to a tolerance of ±0.002 mm, making it suitable as a repeatable reference for comparative and end‑measurement tasks. The 17.28 mm diameter and 50 mm overall length provide a compact datum that is simple to deploy in fixtures, plug gauges and inspection setups. Manufactured from special steel, the pin combines wear resistance with dimensional stability so that reference checks remain consistent over many cycles, reducing rework and inspection variance. Practical workshop design that protects the geometry Engineered as a workshop version, the pin tolerates the rigours of daily use while remaining easy to handle. At approximately 0.15 kg, the component is lightweight yet robust, facilitating fast placement in gauges and locators without causing handling fatigue. Delivery includes a protective transport box, which safeguards the finished surface and maintains geometry during storage and transit — a practical advantage for mobile tooling carts and site use. Traceability and integration into production workflows The gauge pin is supplied as an individually identified item (SKU M323.H28, GTIN 4061905072055), which supports straightforward inventory control and traceability in production environments. Its clear specification and consistent dimensions make it suitable for routine go/no‑go checks, end‑measure verifications and for establishing quick master references when setting up jigs or aligning spindles. The combination of defined tolerance and workshop readiness streamlines quality assurance and reduces downtime during setup. Secure workshop precision with the Metav IndustryLine gauge pin — contact Metav Werkzeuge for delivery details and application guidance. Technical data SKU: M323.H28 GTIN: 4061905072055 Type: Gauge pin, single Length: 50 mm Diameter: 17.28 mm Material: Special steel Tolerance: ±0.002 mm Weight: 0.15 kg Version: Workshop execution Packaging: Delivered in transport box Facts 50 mm 17.28 mm ±0.002 mm 0.15 kg Special features Workshop version Protective transport box included High‑grade special steel Single item supply (individual gauge pin) FAQ What is the dimensional tolerance of this gauge pin? The gauge pin is manufactured to a tolerance of ±0.002 mm, ensuring reliable repeatability for reference and go/no‑go checks. Which material is used for the pin? The pin is made from special steel, selected for wear resistance and dimensional stability suitable for workshop use. Is the item delivered as a single piece or in a set? This listing is for a single gauge pin (SKU M323.H28) supplied individually. Can this pin be used for jig and fixture set‑up? Yes, the diameter and rigid construction make the pin suitable for use as a reference mandrel in jigs, fixtures and alignment tasks. How is the pin protected during transport? The pin is supplied in a protective transport box to preserve surface quality and geometry during storage and transit. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
17.29mm Gauge Pin 50mm Length Workshop Version, Special Steel – Metav IndustryLine
Combine workshop‑grade robustness with laboratory‑level repeatability: a 17.29 mm diameter gauge pin with ±0.002 mm tolerance and a 50 mm length ensures reliable end‑dimension checks; order directly via Metav Werkzeuge or request advice from our consultants. Gauge pin M323.H29 — 17.29 mm diameter, 50 mm length (Metav IndustryLine) The Gauge pin M323.H29 is a single inspection pin engineered for precise end‑dimension verification in workshop environments. Workshop‑grade construction Diameter 17.29 mm nominal Length 50 mm for end measurements Tolerance ±0.002 mm for tight control Precision for small‑scale end measurements The gauge pin is designed for demanding end‑dimension tasks where repeatable contact points matter. With a nominal diameter of 17.29 mm and a verified tolerance of ±0.002 mm, this pin belongs in the micro measurement class (10–100 mm), which is tailored for fine mechanical work and short‑reach checks. The tight tolerance reduces uncertainty in go/no‑go checks and datum setting, enabling faster decision‑making on the shop floor and fewer rejected parts during final inspection. Built‑to‑last material and workshop suitability Manufactured from special steel and supplied in a workshop configuration, the pin balances wear resistance with manageable handling. The 50 mm length gives enough reach for many end‑face and through‑hole verifications while keeping bending and handling simple; the compact form factor supports single‑handed positioning and repeatable contact pressure. The construction reduces maintenance needs and supports a dependable measurement routine without frequent replacement. Practical integration and supply reliability As a single‑item gauge pin, the component integrates easily into existing gauging sets and fixture layouts; traceable identifiers (SKU M323.H29, GTIN 4061905072574) simplify inventory and quality records. The combination of nominal size, precise tolerance and workshop design delivers a pragmatic balance between measurement accuracy and operational efficiency. Metav’s supply chain ensures consistent availability and straightforward procurement for production and quality teams. For precise end‑dimension checks using Metav IndustryLine gauge pins, contact Metav Werkzeuge for product matching and delivery from Emmerich—expert advice is available if additional technical data is required. Technical data Article number: M323.H29 GTIN: 4061905072574 Manufacturer: Metav IndustryLine Weight: 0.15 kg Facts Diameter: 17.29 mm Length: 50 mm Tolerance: ±0.002 mm Weight: 0.15 kg Special features Single gauge pin, workshop version Material: special steel Category: gauge pins Story trigger: end dimensions FAQ What tolerance does the pin provide? The gauge pin offers a tolerance of ±0.002 mm, making the M323.H29 suitable for tight end‑dimension checks. Which measurement class does this pin belong to? With a nominal diameter of 17.29 mm it falls into the micro measurement class (10–100 mm), optimised for fine mechanical and small‑part applications. What material is used for the pin? The pin is made from special steel in a workshop configuration to combine durability with practical handling. Can the pin be used in fixture or gauge sets? Yes; the M323.H29 is a single inspection pin intended for integration into existing gauging arrangements and fixture checks. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
17.2mm Gauge Pin, Workshop Version, 50mm Length, Special Steel, Supplied in Case - Metav IndustryLine
Take advantage of workshop-grade robustness and sub-millimetre accuracy to secure repeatable gauge results; the combination of special steel construction, tight ±0.002 mm tolerance and compact form supports efficient in-process checks and reduces rework. Order the item directly via Metav Werkzeuge or consult our specialists for specification advice. Test pin, single, Ø 17.2 mm, 50 mm length — Metav IndustryLine The Test pin, single, Ø 17.2 mm, 50 mm length is a compact precision gauge pin designed for workshop control tasks and end-measure checks, providing a reliable reference for plug gauges and component verification. Workshop-grade execution Special steel construction Dimensional tolerance ±0.002 mm Supplied in transport case Consistent precision for routine inspection The compact measuring pin delivers repeatable results where short, rigid gauges are required. Manufactured from special steel, this probe maintains geometric stability during handling and is intended for tasks such as end-measure verification and reference fitting. The declared accuracy of ±0.002 mm positions the pin for fine workshop gauging where small tolerances must be upheld; this improves process reliability and reduces the need for corrective rework. As a small-size gauge within the micro range (max. measuring span 10–100 mm), its short form factor keeps deflection minimal, which is especially valuable on small bores and tight fittings. Built for everyday workshop use The workshop version construction focuses on durability and ease of use. A solid, compact design facilitates rapid checking routines on the shop floor and integrates readily with manual fixtures or portable checking rigs. The 50 mm length and Ø 17.2 mm diameter provide a stable contact area while keeping handling straightforward during repetitive measurements. Owing to its material choice and workshop finish, the pin resists wear under normal inspection duties and preserves calibration intervals, supporting consistent metrology practice in busy production environments. Packaging and traceability that suit industry routines Delivered in a transport case, the pin benefits from protected handling and straightforward storage between uses; the box is intended to prevent transit damage and to simplify workshop logistics. Traceability is supported by labelling and the visible SKU, enabling inventory control and replacement planning. Such practical packaging reduces downtime from damaged gauges and helps maintain a tidy inspection station, which contributes to steady throughput and more predictable quality checks. Typical applications and operational fit This measuring pin suits plug gauge verification, end-measure control, assembly checking and component acceptance tests where compact, stiff measuring elements are advantageous. Its tolerance class makes it suitable for fine mechanical parts and precision assemblies often encountered in general engineering and small-series production. Where short-range accuracy and robustness are required, the pin serves as a pragmatic reference element that complements bench instruments and hand gauging tools. For Metav IndustryLine quality and workshop-ready precision, request the M323.H20 gauge pin from Metav Werkzeuge — contact our Emmerich team for tailored ordering and application guidance. Technical Data Article number: M323.H20 GTIN: 4061905071485 Weight: 0.15 kg Facts Length: 50 mm Diameter: 17.2 mm Tolerance: ±0.002 mm Material: Special steel Special features Workshop version Supplied in transport case for transport Compact, rigid geometry SKU: M323.H20 FAQ What is the intended use of this gauge pin? The test pin is intended for workshop inspection tasks such as end-measure checks, plug gauge verification and small-component dimensional control. Which material is the pin made from and why does it matter? The pin is made from special steel; this material provides wear resistance and dimensional stability for repeated use under typical workshop conditions. How precise is the measuring element? The measuring element is specified with an accuracy of ±0.002 mm, suitable for fine inspection tasks where tight tolerances are required. Is the item supplied ready for safe transport and storage? Yes, the gauge pin is supplied in a transport case to protect the part during transit and simplify workshop storage. Metav IndustryLine: Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
17.31mm Gauge Pin 50mm Length Workshop Version - Metav IndustryLine
Take advantage of precise end‑dimension control with a workshop‑grade gauge pin that combines ±0.002 mm accuracy, a 17.31 mm diameter and robust special‑steel construction for dependable routine inspection. Supplied ready for transport in a protective case, the item ensures reproducible measurements and simple handling on the shop floor — order directly via Metav Werkzeuge or consult our specialists for application advice. Gauge pin M323.H31 – single gauge pin, 17.31 mm diameter, 50 mm length (Metav IndustryLine) The Gauge pin M323.H31 is a workshop‑grade inspection pin designed for precise end‑dimension checks and repeatable pass/fail verification in production and quality control. Workshop‑grade finish for robust use Diameter 17.31 mm, tolerance ±0.002 mm Length 50 mm, stable handling Supplied in transport case Precision for reliable end‑dimension checks The M323.H31 delivers high repeatability for routine verification tasks thanks to its guaranteed ±0.002 mm accuracy. As a single‑piece inspection pin with a nominal diameter of 17.31 mm, it provides a clear go/no‑go reference for bores and seats, reducing decision time during quality control. The finely finished measuring surface minimises measurement scatter and supports reproducible readings when used with standard gauge fixtures or manual checking rigs. Built for workshop durability and easy handling Manufactured from special steel, this gauge pin is specified for everyday industrial use and resists wear from repeated insertion cycles. At a length of 50 mm the pin offers a comfortable working grip while maintaining the necessary rigidity for end‑dimension checks; its mass of 0.15 kg aids stable handling without excessive bulk. The workshop‑oriented design balances robustness with manoeuvrability, making the item suitable for inspection benches and portable testing setups alike. Integrates smoothly into quality workflows The pin is classified as a micro‑range inspection tool due to its measuring diameter falling within the compact class typically used for fine mechanical parts; this makes it ideal for small components, precision assemblies and end‑dimension controls in serial production. Supplied in a protective transport case, the pin stays protected in transit and on the shop floor, which helps preserve measurement integrity and reduces downtime caused by surface damage. Practical application and compatibility Intended primarily for end‑dimension verification, the gauge pin functions well as a calibration reference within fixture checks and manual gauging sequences. Its nominal sizing and tolerance make it compatible with common inspection routines and existing checking equipment, enabling quick integration into established quality procedures with minimal adaptation. The robust finish simplifies cleaning and maintenance, supporting long service intervals under normal workshop conditions. For reliable shop‑floor inspections choose the Metav IndustryLine M323.H31 gauge pin — contact Metav Werkzeuge for tailored advice or ordering from Emmerich: info@metav-werkzeuge.com · +49 2822 7131930 Technical Data Article number: M323.H31 GTIN: 4061905072598 Brand: Metav IndustryLine Facts Measuring diameter: 17.31 mm Length: 50 mm Accuracy / tolerance: ±0.002 mm Weight: 0.15 kg Special features Material: special steel Workshop version Supplied in transport case Category: gauge pin FAQ What is the intended use of this gauge pin? The gauge pin M323.H31 is intended for end‑dimension checks and pass/fail verification of bores and seats in production or inspection settings. Does the pin come protected for transport? Yes — the M323.H31 is supplied in a protective transport case to prevent handling damage and to maintain measuring surface condition. What level of accuracy can be expected from the pin? The pin is specified with an accuracy of ±0.002 mm, suited for fine mechanical inspection and consistent routine checks. Which material is used for the pin? The inspection pin is made from special steel, selected for wear resistance and stable surface finish under repeated use. Is the M323.H31 suitable for small precision components? Yes; with a diameter of 17.31 mm and compact length, the pin is classified for micro‑range inspection tasks and integrates well into small‑part quality workflows. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
17.32mm Gauge Pin 50mm Length Workshop Version, Special Steel - Metav IndustryLine
Take advantage of precise dimensional control and robust workshop construction: the combination of high repeatability, tight ±0.002 mm tolerance and a compact 50 mm length keeps inspection and fixture checks efficient and reproducible. Order the gauge pin directly via Metav Werkzeuge or consult their technical advisors for application guidance. Gauge Pin M323.H32 — single precision gauge pin, Ø 17.32 mm, 50 mm length (Metav IndustryLine) The Gauge Pin M323.H32 is a workshop-grade cylindrical reference pin designed for precise end-measure checks, fixture set-up and go/no-go verification in inspection and production environments. Workshop-grade execution Diameter Ø 17.32 mm, length 50 mm High precision ±0.002 mm tolerance Special steel construction Repeatable measurement performance for inspection and setup Precision inspection demands stable references. The Gauge Pin M323.H32 provides a defined cylindrical datum with Ø 17.32 mm and a working length of 50 mm, supplying a compact reference that minimises deformation and handling error during repeated use. With a declared accuracy of ±0.002 mm, the pin supports tight tolerance checks and helps maintain traceable control over end measures. The predictable geometry is particularly useful for quick go/no-go comparisons, plug-in tests and as a transfer standard in toolrooms and small-batch production, where consistent outcomes reduce rework and inspection time. Robust workshop construction that endures daily use Built from special steel, this single gauge pin is engineered for regular handling in workshop conditions. The material choice delivers dimensional stability under typical mechanical stress and contributes to a consistent contact surface for gauging operations. At approximately 0.15 kg, the component balances sturdiness with manageable handling for technicians during fixture assembly or manual inspection routines. The workshop execution emphasizes reliability and ease of use so that the pin resists routine wear while preserving the repeatability expected from a precision reference in a busy production environment. Practical integration into inspection workflows A compact cylindrical reference such as this aids rapid alignment and verification across jigs, fixtures and inspection benches. The single-pin format simplifies inventory and selection for dedicated measurement tasks, and the clear specification streamlines documentation for quality records. The combination of defined diameter, short length and tight tolerance makes the component suitable for end-measure validation, pin-fit testing and as a quick reference in set-up protocols. Using a standardised, well-documented reference reduces ambiguity in inspection reports and supports consistent production decisions across shifts. Contact Metav Werkzeuge for application advice and to order the Metav IndustryLine Gauge Pin M323.H32; email info@metav-werkzeuge.com or call +49 2822 7131930 for tailored guidance Technical data SKU: M323.H32 GTIN: 4061905072604 Label: Prüfstift, einzeln, 17,32 mm Länge 50 mm Category: Messstifte Facts Diameter: 17.32 mm Length: 50 mm Tolerance: ±0.002 mm Weight: 0.15 kg Special features Material: Special steel Workshop execution Single gauge pin format FAQ What tolerance does the pin offer? The Gauge Pin M323.H32 is specified with a tolerance of ±0.002 mm, suitable for tight workshop inspection and repeatable reference tasks. Is the pin made of a corrosion-resistant alloy? The pin is manufactured from special steel chosen for dimensional stability and workshop durability; surface treatment details are not specified in the item data. Can this pin be used for fixture set-up and plug-fit checks? Yes, the single cylindrical format and compact 50 mm length make the pin well suited for fixture alignment, plug-fit testing and quick go/no-go checks. Is the item supplied individually or as a set? The product is offered as a single gauge pin in the specified size and is listed under SKU M323.H32 and GTIN 4061905072604. For which applications is this gauge pin primarily intended? The component is intended for end-measure verification, inspection bench referencing and fixture set-up in machine shops, toolrooms and production environments. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
17.33mm Gauge Pin, 50mm Length, Workshop Version, Special Steel, Delivered in Case - Metav IndustryLine
Take advantage of the combination of workshop-grade robustness, ±0.002 mm tolerance and a compact 50 mm form for reliable in‑process gauging. Order directly via Metav Werkzeuge or consult our specialists for integration advice. Test pin, single, 17.33 mm (Length 50 mm) — Workshop test pin with ±0.002 mm accuracy (Metav IndustryLine) A Test pin, single, 17.33 mm (Length 50 mm) intended for workshop gauging and end‑measure inspections of mating bores and fittings. Workshop design for robust routine use Tolerance ±0.002 mm for high repeatability Special-steel construction for wear resistance Compact 50 mm length for confined spaces Precision that speeds up inspection cycles The compact Test pin delivers a high level of metrological performance thanks to its ±0.002 mm specification, which supports consistent comparative checks and pass/fail decisions at the production line. The tight tolerance reduces rework by providing clear, repeatable results; when used as a reference pin in go/no‑go fixtures or manual gauging jigs, the reduced uncertainty translates directly into fewer false rejects and faster throughput. The robust workshop layout keeps handling simple and shortens the time from measurement to decision. Small package, big application range With a nominal diameter of 17.33 mm and an overall 50 mm length, the component is designed for confined assemblies and fixture stations where accessibility is limited. The pin’s compact geometry makes it easy to fit into close‑tolerance bores, plug gauges and alignment checks without requiring special adapters. At a weight of 0.15 kg the item is simple to position by hand or to clamp into standard holding devices, supporting quick repeat measurements and efficient shop‑floor workflows. Durable construction for everyday reliability Manufactured from special steel, the pin resists wear in frequent inspection use and maintains form integrity across many cycles. The workshop design focuses on practical handling: straightforward mounting, robust seating and minimal risk of deformation under routine contact. These properties ensure sustained repeatability and a long service life, lowering replacement frequency and supporting a dependable quality assurance routine in small and medium production environments. Contact Metav Werkzeuge for bespoke advice on integrating this Metav IndustryLine test pin into inspection jigs and to confirm availability from our Emmerich stock. Technical data SKU: M323.H33 GTIN: 4061905072611 Label: Test pin, single, 17.33 mm length 50 mm Material: Special steel Length: 50 mm Nominal diameter: 17.33 mm Tolerance: ±0.002 mm Weight: 0.15 kg Design: Workshop execution Category: Gauging pins / Messstifte Facts Measurement nominal: 17.33 mm Length nominal: 50 mm Mass: 0.15 kg Accuracy class: ±0.002 mm Single piece supply Special features Robust workshop design High wear resistance due to special-steel material Compact geometry for confined spaces FAQ What level of accuracy does this test pin provide? The Metav IndustryLine test pin M323.H33 is specified to ±0.002 mm, providing high repeatability for comparative gauging and go/no‑go checks. Is the pin suitable for use in manual gauging jigs and fixtures? Yes — the compact 50 mm length and 17.33 mm nominal diameter make the pin well suited to manual jigs, plug gauges and fixture stations in workshop environments. What is the material and how does it affect longevity? The component is made from special steel, chosen for wear resistance and form stability to ensure prolonged service life under routine inspection use. Can the pin be used for alignment checks on assemblies? The robust workshop design and precise nominal diameter allow reliable alignment and end‑measure checks on mating parts and assemblies. Metav IndustryLine: Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
17.34mm Gauge Pin Length 50mm Workshop Finish, ±0.002mm - Metav IndustryLine
Benefit from workshop-grade construction, special steel and ±0.002 mm tolerance for consistent, repeatable checks in production. Combine precise diameter control and a compact 50 mm length for easy fixture access; order the gauge pin directly via Metav Werkzeuge or consult our advisors for specification guidance. Gauge pin, single — Ø 17.34 mm, length 50 mm (Metav IndustryLine) The gauge pin, single, 17.34 mm, length 50 mm is a workshop-grade verification pin intended for end‑dimension checks and fit verification in production, assembly and inspection tasks. Workshop-grade construction Diameter 17.34 mm precision fit Length 50 mm for fixture access Supplied in transport case Durable tool for routine verification with measurable benefits The compact verification pin delivers repeatable dimensional control where small deviations matter. Machined from special steel, the pin resists wear and maintains contact geometry during repeated use; this ensures that run-to-run checks remain consistent and that fixture alignments do not drift. The declared tolerance of ±0.002 mm classifies the component for fine verification tasks in workshop environments, supporting quick go/no-go decisions and reducing rework rates by identifying out-of-spec parts early in the process. Space-efficient design for tight fixtures and assemblies With a 50 mm overall length and a diameter of 17.34 mm, this test pin is designed to access recessed bores, gauge blocks and assembly seats without interfering with surrounding features. The short, rigid profile minimises bending and ensures stable seating during measurement or fitting operations; this makes it suitable for both handheld checks and use in simple fixture setups. The moderate mass and compact form factor also simplify handling during repetitive checks on production lines. Practical supply and traceability for production use Delivered as a single item in a protective transport case, the component is ready for immediate use on the shop floor and protected during storage and transit. Marked with SKU M323.H34 and GTIN 4061905072628, the part integrates into inventory systems and quality records with minimal administrative overhead. The workshop specification and robust material selection contribute to predictable service life, enabling scheduled replacement intervals rather than unscheduled downtime. For reliable workshop verification with Metav IndustryLine quality, contact Metav Werkzeuge to discuss M323.H34 availability and application advice. Technical data Article number: M323.H34 GTIN: 4061905072628 Manufacturer: Metav IndustryLine Diameter: 17.34 mm Length: 50 mm Tolerance: ±0.002 mm Weight: 0.15 kg Workshop execution Material: Special steel Supplied in transport case Single gauge pin FAQ What tolerance does the gauge pin offer? The gauge pin is specified with a tolerance of ±0.002 mm, suitable for fine workshop verification and fit checks of mating parts. What material is used for the pin? The pin is manufactured from special steel, chosen for wear resistance and dimensional stability under repeated use. Is the pin supplied ready for use and how is it packaged? The single gauge pin M323.H34 is supplied in a transport case to protect the part during storage and transit and to facilitate safe handling. Which applications suit this gauge pin best? The component is intended for end-dimension checks, fit verification and fixture testing in production and assembly contexts where compact, rigid gauges are required. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
17.35mm Gauge Pin, Workshop Version, 50mm Length - Metav IndustryLine
The 17.35 mm diameter and 50 mm length deliver consistent micro‑diameter inspection with ±0.002 mm accuracy, combining repeatability and shop‑floor robustness for reliable Go/No‑Go checks. Order the inspection pin directly via Metav Werkzeuge or contact our consultants for technical advice. Test pin M323.H35 – Precision inspection pin, Ø17.35 mm × 50 mm (Metav IndustryLine) The Test pin M323.H35 is a single inspection pin designed for accurate dimensional checking of small bores and gauge assemblies in workshop environments. Diameter 17.35 mm for precise bore checks Length 50 mm, robust workshop execution Tolerance ±0.002 mm for high repeatability Micro‑diameter accuracy that fits compact workpieces The M323.H35 is built for micro‑diameter inspection tasks where compactness and stability matter. With a nominal Ø17.35 mm and a 50 mm overall length, the pin falls squarely into the micro category (max. range 10–100 mm), which is the preferred class for fine mechanical components and small assemblies. The short shank geometry reduces torsion and handling errors, enabling reproducible Go/No‑Go checks and quick verification of end dimensions. The ±0.002 mm stated positional accuracy positions this pin beyond coarse shop tolerances and closer to high‑precision workshop demands, ensuring reliable pass/fail decisions without lengthy setups. Workshop execution for everyday durability and handling Designed as a workshop execution item, this inspection pin balances resilience with tactile usability. Manufactured from special steel, the component resists routine knocks and maintains the measuring face geometry under regular shop use. The compact mass and ergonomic proportions make fitting into fixtures and gauge blocks straightforward while reducing the risk of deformation during handling. These attributes translate into fewer measurement interruptions and a lower rate of rework; the physical design emphasises practical longevity rather than delicate laboratory handling, which suits busy production floors and tooling departments. Integrates into inspection workflows to boost throughput As a straightforward inspection artefact, the M323.H35 speeds up quality control cycles by providing a stable reference for quick checks at incoming inspection stations or final assembly. The combination of a defined diameter, controlled length and tight tolerance minimises uncertainty in decision chains, allowing quality teams to act fast and with confidence. Using robust, repeatable gauges reduces stoppages caused by ambiguous measurements and supports leaner throughput. Metav’s focus on democratising precision means the component is offered with clear sourcing and logistical support from Emmerich, simplifying procurement and ensuring dependable replenishment for production environments. Choose the Metav IndustryLine test pin for precise micro‑diameter verification—contact Metav Werkzeuge in Emmerich for specification clarification and ordering support at info@metav-werkzeuge.com or +49 2822 7131930 Technical data Article number: M323.H35 GTIN: 4061905069536 Material: Special steel Weight: 0.15 kg Facts Diameter (nominal): 17.35 mm Length: 50 mm Accuracy / tolerance: ±0.002 mm Category: Test pin, single Special features Workshop execution Compact geometry for micro‑diameter inspection Robust design for routine shop use FAQ What is the intended application of this test pin? The M323.H35 inspection pin is intended for quick dimensional checks of small bores and gauge assemblies where a precise reference pin is required. Is the M323.H35 suitable for laboratory calibration tasks? The M323.H35 is specified for workshop use and routine inspection; its ±0.002 mm tolerance supports high repeatability on the shop floor rather than specialised metrology lab applications. Which material is used for the pin and how does it affect durability? The pin is made from special steel, chosen to provide resistance to wear and mechanical stress typical in daily workshop handling. Can the pin be used in gauge blocks and fixture assemblies? Yes, the compact Ø17.35 mm and 50 mm length make the pin compatible with many gauge and fixture configurations designed for micro‑diameter verification. How does the specified accuracy compare to common workshop tools? With a tolerance of ±0.002 mm, the pin offers greater precision than coarse workshop standards and approaches the needs of high‑precision inspection routines. Metav IndustryLine: Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
17.36mm Test Pin 50mm Length Workshop Version Special Steel - Metav IndustryLine
Take advantage of high repeatability, robust workshop design and a compact form factor to simplify end‑limit checks and keep inspection routines efficient; order the gauge pin directly via Metav Werkzeuge or consult our advisors for application support. Gauge pin M323.H36 — precision test pin, 17.36 mm Ø, 50 mm length (Metav IndustryLine) The Gauge pin M323.H36 serves as a compact reference pin for end‑measure checks and go/no‑go verification in workshop inspection and small‑series quality control. Workshop version for robust daily use Diameter precisely 17.36 mm ±0.002 Length 50 mm in special steel construction Supplied in protective transport case Consistent measurement where it matters A compact precision pin designed for repeatable end‑measure checks, the gauge pin offers a diameter of 17.36 mm with a declared tolerance of ±0.002 mm, which translates into reliable go/no‑go decisions during routine inspection. The tight tolerance reduces ambiguity in acceptance criteria and shortens decision loops on production lines. The specified variance corresponds to high‑precision workshop checks and supports traceable dimensional control when used as a reference in go/no‑go fixtures or manual gauge benches. Built for workshop handling and protection Specified as a workshop version, this test pin is manufactured from special steel to withstand everyday handling and contact with gauge holders. Its 50 mm length balances reach with ease of manipulation, and the supplied protective case ensures secure transport and storage between uses. The robust construction reduces the risk of deformation and helps maintain the declared tolerance over repeated cycles, thereby lowering the need for frequent replacement and keeping maintenance predictable. Seamless integration into inspection routines Engineered for straightforward use in small‑series production and maintenance shops, the pin slips easily into existing checking jigs and manual fixtures. The compact form factor supports fast sampling and quick pass/fail evaluations, helping to maintain throughput without sacrificing control. Alongside its mechanical stability, the clear specification and stock availability from a European quality filter support procurement decisions and minimise lead times for repeat orders. Request the Metav IndustryLine gauge pin from Metav Werkzeuge for reliable end‑measure control and immediate integration into workshop inspection processes; contact Metav Werkzeuge by phone +49 2822 7131930 or e‑mail info@metav-werkzeuge.com for technical advice or to confirm availability. Technical data Article number: M323.H36 GTIN: 4061905069543 Category: Messstifte Length: 50 mm Nominal diameter: 17.36 mm Accuracy: ±0.002 mm Weight: 0.15 kg Material: Special steel Workshop execution Supplied in protective transport case Single gauge pin FAQ What tolerances can be expected from this gauge pin? The gauge pin is specified with an accuracy of ±0.002 mm, making the M323.H36 suitable for tight workshop inspection and clear go/no‑go assessment. Which material is used for the pin and what does that mean for durability? Manufactured from special steel, the pin offers resistance to routine wear in workshop environments; regular handling in the supplied protective case maintains dimensional integrity. Can the pin be used in existing gauge holders and jigs? Yes, the 17.36 mm nominal diameter and 50 mm length are compatible with standard manual fixtures and gauge benches used for end‑measure verification. Is this item supplied ready for storage and transport? Delivery includes a protective transport case, which protects the pin during storage and movement between inspection stations. What is the product identifier for ordering and traceability? The product is listed as Gauge pin M323.H36 (SKU M323.H36, GTIN 4061905069543) in the Metav IndustryLine range. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
17.37mm Gauge Pin 50mm Length Workshop Version, Special Steel - Metav IndustryLine
Reliable workshop‑grade precision for end‑size checks: the gauge pin offers a diameter of 17.37 mm with a manufacturing tolerance of ±0.002 mm and a 50 mm shaft made from special steel, ensuring repeatable results in fixture setup and inspection. Order the component directly via Metav Werkzeuge or consult our specialists if specification advice is needed. Gauge pin (17.37 mm), 50 mm length — Metav IndustryLine A precision gauge pin designed for end‑size inspection and fixture alignment in demanding workshop environments Workshop-grade design for rugged use Diameter exactly 17.37 mm precision ±0.002 50 mm special-steel shaft Ideal for end-size inspection and fixture set-up Precision that reduces rework and inspection time The 17.37 mm gauge pin is manufactured to a tight tolerance of ±0.002 mm, enabling reliable go/no‑go assessments and dimensional checks on finished parts. High repeatability during iterative checks helps to reduce scrap and rework by catching deviations early in the production flow. The precision of the component supports process control routines and contributes to a consistent quality record in batch inspection and small‑series production. Robust material and compact form for workshop use Constructed from special steel, the shaft combines stiffness with wear resistance appropriate for regular use on shop floors. The 50 mm overall length provides a stable engagement depth for many fixturing operations while remaining easy to handle during manual checks. The workshop version designation indicates a design balanced between durability and economical manufacture, making it suitable for routine inspection tasks and integration into assembly jigs. Practical deployment in quality routines and fixtures As a compact inspection element, the gauge pin simplifies end‑size verification, alignment of locating features and validation of bore diameters where a fixed reference mandrel is required. Its modest mass and precise diameter permit quick insertion and withdrawal without special tools, accelerating operator workflows. For traceability and inventory management the component is listed as M323.H37, supporting clear identification in tool lists and inspection reports. For specification advice or to secure the Metav IndustryLine gauge pin (M323.H37) for workshop inspection tasks, contact Metav Werkzeuge to arrange purchase details or technical clarification via info@metav-werkzeuge.com or +49 2822 7131930 Technical data Article number: M323.H37 GTIN: 4061905069550 Brand: Metav IndustryLine Core specifications Diameter: 17.37 mm Length: 50 mm Tolerance: ±0.002 mm Weight: 0.15 kg Materials & features Material: Special steel Workshop version Accuracy class: ±0.002 FAQ What is the primary use for this gauge pin? The gauge pin (Metav IndustryLine M323.H37) is intended for end‑size inspection, locating and fixture alignment tasks where a precise reference diameter is required. What tolerance does the component provide? The component is manufactured to a tolerance of ±0.002 mm, enabling high‑precision go/no‑go verification and dimensional checks. What is the material and build quality of the pin? Made from special steel, the pin is produced as a workshop version designed for regular use and stable handling during inspection and fixturing. Is the diameter exactly 17.37 mm? Yes, the nominal diameter is 17.37 mm, with the stated tolerance of ±0.002 mm governing permissible deviation. How can the part be identified in documentation? The component is listed under article number M323.H37 and GTIN 4061905069550 for unambiguous identification. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
17.38mm Test Probe 50mm Length Workshop Version - Metav IndustryLine
Benefit from the combination of workshop-grade robustness, a ±0.002 mm tolerance and a 50 mm length for consistent end‑measure results. Order the gauge pin directly via Metav Werkzeuge or ask our consultants if needed. Gauge pin, single, 17.38 mm — 50 mm length | Metav IndustryLine The gauge pin, single, 17.38 mm is a hardened inspection pin designed for precise end‑measure checks and plug gauging in workshop metrology. Precision ±0.002 mm tolerance Nominal diameter 17.38 mm Length 50 mm workshop version Special steel hardened construction Repeatable results for everyday workshop control This inspection pin delivers a reliable metrological reference for repetitive end‑measure tasks. With a ±0.002 mm runout specification, the pin stabilises measurement variance and supports consistent pass/fail decisions on small components. The compact 50 mm shank and fine nominal diameter make it suitable for plug‑gauge comparisons and fit tests where small deviations influence assembly quality. The robust design reduces the need for frequent rework and thus contributes to smoother production flow. Hardened material and construction that withstands daily use Manufactured from special steel and supplied as a workshop configuration, the pin balances durability with dimensional integrity. The choice of material and heat treatment ensures long wear life under typical inspection cycles while preserving the calibrated geometry essential for accurate gauging. The construction minimises surface wear and keeps the gauge geometry stable over repeated insertions, supporting reduced downtime and predictable inspection intervals. Practical fitment and straightforward integration into quality routines The nominal 17.38 mm diameter and 50 mm length allow straightforward incorporation into existing gauge sets or dedicated checking fixtures. Its compact form factor is compatible with handheld gauge holders and bench fixtures, enabling simple alignment and rapid checks without complex fixturing. When used as part of a standard control plan, the pin gives clear, measurable results that feed directly into process control charts or inspection records, aiding traceability and quicker corrective actions. Contact Metav Werkzeuge today to specify the M323.H38 gauge pin for workshop use and to arrange delivery from Emmerich; email info@metav-werkzeuge.com or call +49 2822 7131930 for precise guidance. Technical data SKU: M323.H38 GTIN: 4061905069567 Manufacturer: Metav IndustryLine ECLASS: 21170231 Facts Diameter: 17.38 mm Length: 50 mm Weight: 0.15 kg Tolerance: ±0.002 mm Special features Material: special steel Workshop version Category: gauge pins Article label: Gauge pin, single, 17.38 mm length 50 mm FAQ What applications suit this gauge pin best? This gauge pin is intended for plug gauging, end‑measure checks and small‑part fit tests; the M323.H38 from Metav IndustryLine is optimised for routine workshop inspection tasks. What is the declared tolerance and how does it affect measurements? The pin carries a tolerance of ±0.002 mm, which ensures tight repeatability for dimensional checks and helps reduce measurement uncertainty during frequent conformance testing. Which material is used and what does that mean for durability? The gauge pin is made from special steel, giving the M323.H38 good wear resistance and dimensional stability under normal inspection cycles. Can the pin be used in bench fixtures or handheld holders? Yes, the 50 mm length and compact profile make the pin suitable for both handheld gauge holders and common bench fixtures without additional modification. Is the product compatible with standard gauge sets? The nominal diameter and standard form factor allow easy integration into existing gauge sets and checking routines, aiding straightforward replacement or extension of current equipment. Metav IndustryLine: Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
17.39mm Gauge Pin 50mm Length Workshop Finish - Metav IndustryLine
Take advantage of precision, robust workshop design and repeatable end‑size verification with this inspection component; the combination of ±0.002 mm accuracy, 17.39 mm diameter and durable special steel makes it a reliable choice for quality control. Order the gauge pin directly via Metav Werkzeuge or consult our specialists for application advice. Gauge pin 17.39 mm Ø, 50 mm length (Metav IndustryLine) A gauge pin 17.39 mm engineered for precise end‑size checks and plug‑in verification in metrology and workshop inspection. Workshop version, robust design Diameter 17.39 mm for end‑size checks Length 50 mm for standard fixtures Tolerance ±0.002 mm for tight measurements Repeatable end‑size verification for routine quality control The gauge pin provides a straightforward, measurable reference for end‑size and plug checks, combining a 17.39 mm diameter with a 50 mm length to suit common fixture depths. Constructed from special steel, the pin resists deformation under frequent use and maintains dimensional stability, which supports consistent results during repetitive inspections. The declared ±0.002 mm tolerance signals suitability for tasks that demand close control, such as final component verification and assembly checks, reducing uncertainty in go/no‑go decisions. Robust workshop construction that endures handling Designed as a workshop version, the pin tolerates everyday handling without compromising accuracy. The compact mass of 0.15 kg and short, stable geometry aid quick positioning in gauges, minimising fixturing time and helping to keep inspection cycles efficient. Where repeatable seating and minimal lateral play are essential, the pin’s construction preserves alignment in jigs and plate fixtures, lowering the risk of measurement drift and enabling reliable throughput on the shop floor. Quick integration into gauges and inspection jigs The pin’s consistent diameter and straightness allow seamless insertion into standard gauge blocks, bushings and dedicated fixtures; this simplifies setup and speeds up batch checks. By converting a measured variable into a simple plug verification, the component contributes directly to a smoother production flow: fewer interruptions, faster acceptance checks and clearer decision thresholds for quality control. Clear numerical specifications make it easier to plan probe positions and define acceptance bands in inspection plans. Sourced to support precision across workshops and small series Backing the component is Metav’s practical approach to industrial supply: a focused range and dependable logistics from Emmerich that bring precise measuring aids within reach of workshops and small production lines. Choosing this gauge pin means relying on a supplier that emphasises accessibility to accurate tools and a pragmatic supply chain, helping maintain consistent quality without unnecessary complexity. Request tailored guidance from Metav Werkzeuge for correct selection and rapid delivery from Emmerich to the workshop. Technical Data Article number: M323.H39 GTIN: 4061905069574 SKU: M323.H39 Material: Special steel Accuracy: ±0.002 mm Diameter: 17.39 mm Length: 50 mm Weight: 0.15 kg Facts Diameter: 17.39 mm Length: 50 mm Weight: 0.15 kg Tolerance: ±0.002 mm GTIN: 4061905069574 Special features Workshop version robust design Single inspection/gauge pin Suitable for end‑size and plug checks Special steel construction Compact geometry for fixtures FAQ What is the nominal diameter and length of this pin? The gauge pin has a nominal diameter of 17.39 mm and a length of 50 mm (SKU M323.H39). What accuracy can be expected for measurements with this pin? The inspection pin is specified with an accuracy of ±0.002 mm, suitable for tight tolerance verification. Which material is used for the pin? The pin is manufactured from special steel, chosen for dimensional stability and workshop durability. Is the product suitable for integration in standard jigs and bushings? Yes. The consistent diameter and straight geometry make the pin appropriate for use in standard gauges, bushings and bespoke inspection jigs. Who supplies this gauge pin and where is it shipped from? This component is part of the Metav IndustryLine range and supplied via Metav Werkzeuge with logistics centred in Emmerich. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
17.3mm Gauge Pin, Workshop Version, 50mm Length - Metav IndustryLine
Take advantage of a combination of precision, robust workshop design and compact dimensions for consistent end-measurements; order the M323.H30 directly via Metav Werkzeuge or consult our specialists for application advice. Gauging pin M323.H30 — single inspection pin, Ø 17.3 mm, 50 mm length (Metav IndustryLine) The gauging pin M323.H30 is a compact, workshop-grade inspection pin designed for reliable end-dimension checks and fixture verification in production and inspection settings. Workshop version for robust use Diameter 17.3 mm for end-measurements High accuracy ±0.002 mm Durable design for repeated inspection cycles The M323.H30 is built as a workshop version, combining a compact form with material choices that resist everyday wear. The body is made from special steel, hardened and finished for stable contact behaviour and long service life. This construction reduces the need for frequent replacement, ensuring steady throughput in repetitive inspection tasks and minimising downtime caused by tool wear. Measurement certainty that supports quality control With a nominal diameter of 17.3 mm and a declared accuracy of ±0.002 mm, the pin provides a dependable reference for end-measurements and go/no-go checks. The tight tolerance supports quality assurance processes where repeatability is critical; for instance, it helps verify bores, seats and fixture positions to prevent assembly errors. The small, rigid geometry concentrates contact forces, improving reproducibility compared with larger, more flexible gauges. Compact handling and integration into inspection routines At 50 mm overall length and weighing approximately 0.15 kg, the pin is straightforward to handle and slot into standard test setups or bespoke fixtures. The single-piece format simplifies component management on the shop floor and speeds up measurement routines in busy inspection benches. Traceable identification is supported by the SKU and GTIN, facilitating inventory control and process documentation in manufacturing environments. For procurement or technical clarification about the M323.H30 gauging pin, contact Metav Werkzeuge in Emmerich for specialist advice and order guidance. Technical data SKU: M323.H30 GTIN: 4061905072581 Label: Prüfstift, einzeln, 17,3 mm Länge 50 mm Facts Diameter: 17.3 mm Length: 50 mm Weight: 0.15 kg Accuracy: ±0.002 mm Special features Workshop version Material: special steel Single inspection/gauging pin Designed for end-measurements FAQ What is the primary application for this pin? The M323.H30 gauging pin is intended for end-dimension checks, fixture verification and go/no-go inspection of bores and seats in production and quality-control environments. What tolerance can be expected from the pin? The inspection pin is specified with an accuracy of ±0.002 mm, which makes it suitable for fine inspection tasks and repeatable reference measurements. Which material is the pin made from and why does it matter? Manufactured from special steel, the pin offers improved wear resistance and consistent contact behaviour, which preserves dimensional reliability over many inspection cycles. How does the size affect its use in fixtures? With a diameter of 17.3 mm and a length of 50 mm, the pin is compact enough for tight test stations yet rigid enough to provide reproducible readings when used in standard fixture arrangements. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
17.41mm Gauge Pin, Single, 50mm Length, Workshop Version - Metav IndustryLine
Take advantage of a compact workshop design combined with special steel construction and an accuracy of ±0.002 mm for reliable end‑measurement checks; order the gauge pin directly via Metav Werkzeuge or ask our consultants if needed. Gauge pin, single – 17.41 mm Ø, 50 mm length (Metav IndustryLine) Gauge pin, single, 17.41 mm for precise end‑measure verification and fit checks in workshop and production metrology. Single gauge pin, workshop version Diameter 17.41 mm for precise fit checks Length 50 mm, stable handling Accuracy ±0.002 mm for repeatable results Consistent fit and assembly checks with measurable accuracy The compact test pin is engineered for repeatable dimensional control where end‑measure verification matters. With a nominal diameter of 17.41 mm and an indicated accuracy of ±0.002 mm, the device supports tight tolerance assessment in assembly and inspection routines. The small footprint and solid geometry reduce the influence of lateral play, so measurements remain consistent across repeated cycles; this converts technical specification into dependable shop‑floor performance. Robust material and workshop handling for daily use Built from special steel in a workshop design, the pin balances wear resistance with dimensional stability under regular handling. The 50 mm length offers a practical grip and insertion depth for standard fixture checks while keeping the component easy to manoeuvre. The construction is aimed at routine metrology tasks where a robust feel and low maintenance are important, translating material choice into longer service life and fewer replacements. Practical integration into quality workflows As a single gauge element, the pin functions as a reference for go/no‑go assessments, seating trials and clearance verification in production lines. Marking and handling are optimised for quick identification within kits; the simple geometry enables rapid comparison and fast decisions during inspection steps. The clear numerical tolerance specification supports traceable documentation and quality records, aligning technical capability with efficient process control. For repeatable end‑measure checks and workshop standards, request the Metav IndustryLine gauge pin (SKU M323.H41) from Metav Werkzeuge by email at info@metav-werkzeuge.com or by phone on +49 2822 7131930 Technical Data Article number: M323.H41 GTIN: 4061905069598 Description: single gauge pin, Ø 17.41 mm, length 50 mm Manufacturer: Metav IndustryLine Weight: 0.15 kg Facts Diameter: 17.41 mm Length: 50 mm Tolerance/accuracy: ±0.002 mm Weight: 0.15 kg Special features Material: Special steel Workshop version Application: end‑measure checks and fit verification SKU: M323.H41 FAQ What tolerance can be expected from this gauge pin? The gauge pin is specified with an accuracy of ±0.002 mm, allowing the Metav IndustryLine single gauge pin (SKU M323.H41) to be used for precise fit and clearance checks. Is the pin suitable for use in assembly fixtures and seating tests? Yes, the 50 mm length and robust workshop design make the pin appropriate for seating trials, fixture trials and quick go/no‑go assessments in production environments. What material is the pin made from and what does that mean for wear? Constructed from special steel, the pin offers improved wear resistance and dimensional stability under normal workshop handling, supporting longer interval use before replacement. Can this pin be used as a reference for quality documentation? The clear nominal diameter and stated tolerance permit inclusion in inspection records and quality documentation as a repeatable reference element. How should the pin be handled to preserve accuracy? Handle the pin with care, avoid impact or bending forces and store it with other precision tools to prevent abrasion; these measures help maintain the specified ±0.002 mm accuracy. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
17.42mm Gauge Pin Length 50mm Workshop Finish - Metav IndustryLine
Take advantage of precision, robust workshop design and traceable identification to keep dimensional checks efficient and reproducible; the combination of ±0.002 mm tolerance, 17.42 mm nominal diameter and compact 50 mm length supports reliable end‑measure verification — request the part via Metav Werkzeuge or consult the technical team for application advice. Gauge Pin M323.H42 — 17.42 mm, 50 mm Length (Metav IndustryLine) Gauge Pin M323.H42 is a single precision gauge pin designed for end‑dimension verification in workshop inspection and fixture checks. Workshop-grade finish Diameter 17.42 mm for end-size checks Tolerance ±0.002 mm accuracy 50 mm special-steel construction Ensure reproducible size control on the production line High repeatability in dimensional inspection reduces rework and streamlines quality gates. The 17.42 mm nominal diameter combined with a declared ±0.002 mm tolerance provides a tight acceptance criterion that is suitable for close‑tolerance fits and final inspection. As a hardened inspection pin alternative, this type of gauge is used for quick pass/fail verification of bores, seats and end dimensions; calibrated master gauges and systematic use of a reference set raise overall measurement confidence. The compact form factor allows installation in gauges and fixtures where a stable reference is required without excess overhang. Durable workshop design for frequent handling Built in a workshop version finish from special steel, the pin is dimensionally stable and resistant to the knocks and handling typical in everyday inspection routines. The 50 mm length provides sufficient engagement for end‑measure checks while remaining easy to manipulate and mount in test fixtures. Low mass and compact geometry support fast tool changes and simple storage in dedicated holders. The construction focuses on robustness and serviceability rather than decorative finishes, making it a practical choice for maintenance, assembly and quality control stations. Integrates with inspection processes and traceability systems Marked with SKU M323.H42 and full GTIN identification, the pin can be recorded in inventory and inspection logs to support traceability. Its single‑piece configuration simplifies fixture design and reduces setup errors when verifying end dimensions during batch runs. Where serial documentation is required, this gauge can be referenced in inspection protocols and work instructions to ensure consistent acceptance criteria across shifts. For users needing confirmation of specification compliance, the clear numerical tolerance and nominal size make the component straightforward to incorporate into quality plans and measurement reports. For technical selection or to request the M323.H42 gauge pin from Metav IndustryLine, contact Metav Werkzeuge for specification guidance and delivery options at info@metav-werkzeuge.com or by phone on +49 2822 7131930 — our technical consultants are available to advise on integration into existing inspection routines. Technical data Article number: M323.H42 GTIN: 4061905069994 Label: Gauge pin, single, 17.42 mm, length 50 mm ECLASS: 21170231 Facts Diameter: 17.42 mm Length: 50 mm Weight: 0.15 kg Tolerance: ±0.002 mm Special features Material: special steel Version: workshop execution Category: gauge pins SKU: M323.H42 FAQ What tolerance does the gauge pin provide? The M323.H42 gauge pin from Metav IndustryLine is specified with a tolerance of ±0.002 mm, making it suitable for tight end‑dimension verifications. For which inspection tasks is this pin intended? This single gauge pin is intended for end‑size and bore checks, seating verification and fixture reference tasks where a 17.42 mm nominal plug is required. What material and finish does the pin have? The pin is manufactured from special steel with a workshop execution finish designed for robust everyday handling. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
17.43mm Gauge Pin 50mm Length Workshop Version - Metav IndustryLine
Take advantage of precise tolerance, robust workshop design and secure transport packaging to keep inspection workflows consistent; order the component directly via Metav Werkzeuge or ask our consultants for application support. Gauge pin, single Ø 17.43 mm, length 50 mm (Metav IndustryLine) The Gauge pin, single Ø 17.43 mm, length 50 mm serves as a compact workshop test pin for end‑dimension checks and plug‑gauge applications in inspection routines. Workshop-grade construction Special steel for wear resistance Dimensional tolerance ±0.002 mm Consistent measurement accuracy for routine inspections The pin is designed to deliver reliable precision where repeatable checks are required. With a nominal diameter of 17.43 mm and a verified tolerance of ±0.002 mm, the component supports tight control limits in production monitoring and manual inspection stations. Its defined tolerance reduces uncertainty during fit and clearance tests, enabling faster go/no‑go decisions and fewer follow‑up adjustments in the production chain. The measured stability of the test pin helps maintain documented quality levels and simplifies traceable inspection protocols. Robust workshop design that withstands daily use Built in a workshop execution and produced from special steel, the test pin resists wear and surface damage encountered in frequent handling. The hardened material and concise geometry optimise contact stability and reduce profile deformation under repeated insertion. Supplied as a single, ready‑to‑use pin, it integrates easily into fixtures, plug gauges or bespoke inspection jigs. A secure transport case is provided for safe storage and reduced risk of transit damage, helping to preserve the pin's calibrated condition during logistics and workshop routines. Practical integration into inspection workflows Lightweight and compact, the gauge pin simplifies handling and placement in assemblies where quick dimensional verification is required. Its consistent dimensions support quick verification of mating bores, stepped features and alignment aids without complex set‑ups. Documentation‑friendly identification (SKU and GTIN) assists in inventory control and replacement planning, while the straightforward design keeps maintenance and cleaning simple, supporting a high throughput of checks with minimal operator training. Contact Metav Werkzeuge in Emmerich for matching gauge solutions and consultation on how this Metav IndustryLine test pin fits existing inspection procedures — eMail info@metav-werkzeuge.com or call +49 2822 7131930 Technical data SKU: M323.H43 GTIN: 4061905070006 Product: Gauge pin, single Facts Diameter: 17.43 mm Length: 50 mm Weight: 0.15 kg Tolerance: ±0.002 mm Special features Material: Special steel Workshop execution Delivered in transport case Single test pin FAQ What nominal diameter does the gauge pin have? The Gauge pin, single Ø 17.43 mm, length 50 mm has a nominal diameter of 17.43 mm for end‑dimension verification. What tolerance is specified for this test pin? A dimensional tolerance of ±0.002 mm is specified for the pin, supporting fine acceptance criteria in inspection tasks. Which material is used for the pin? The pin is manufactured from special steel in a workshop execution to improve surface durability during frequent use. How is the pin supplied and stored? The gauge pin is supplied as a single item and is provided with a transport case to protect the component during transit and storage. For which applications is this pin suitable? The test pin is suitable for plug‑gauge checks, end‑dimension inspections, fixture validation and alignment tasks within standard workshop and production inspection workflows. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
Fast, tactile checks where electronics are impractical
Gauges and test pins provide unequivocal go/no-go results for threads, bores, gaps and radii without relying on electronics. The range covers plug gauges and ring gauges for internal and external threads, feeler gauges and precision feeler strips for micro‑gap assessment, plus probe pins and measuring pins for tactile diameter and pitch checks.
How these tools work in the production environment
Mechanical gauges operate as direct reference standards: a plug gauge or ring gauge verifies conformity to thread profiles and mating ability, while limit gauges separate accept from reject in a single step. Test pins are used to tactilely measure small bore diameters, centre‑to‑centre distances and radii. Manufactured from hardened gauge steel or ceramic and often precision lapped, these instruments deliver immediate physical results that are ideal for incoming inspection, machine‑side checks and final control.
Measurable benefits that affect production performance
- Reduced scrap and rework through rapid, unambiguous pass/fail assessment.
- Increased repeatability thanks to very low measurement uncertainty and fine lapping.
- Lower downtime: quick checks at the machine save cycle time and reduce setup periods.
- Durable construction with high wear resistance from specialised, low‑distortion alloys.
- Versatile delivery formats: individual gauges, organised sets in wooden cases or metre‑length feeler rolls compliant with DIN 2269.
Why Metav is the practical choice for precision supplies
Metav combines decades of expertise with a broad warehouse and quality filtering from Emmerich. As a precision partner for industry, craft and trade, Metav supplies a comprehensive selection of gauges and test pins alongside complementary tools such as precision calipers and setting rings. With over 48,000 customers and a catalogue exceeding 250,000 items, Metav is positioned to supply reliably, reduce vendor complexity and support traceable quality control to national standards.
Summary
Gauges and test pins are indispensable for dependable, repeatable quality assurance where tactile, mechanical verification is preferred. Choose these plug gauges, ring gauges, feeler strips and probe pins when immediate, robust measurement decisions are required on the shop floor.
FAQ
What materials are gauges and test pins typically made from?
Gauges and test pins are usually manufactured from hardened gauge steel for durability and wear resistance; ceramic variants are available where thermal stability and minimal wear are critical.
How do thread gauges ensure mating capability?
Thread plug gauges and ring gauges check flank diameters and thread form against standards, providing a clear go/no‑go verdict that confirms pairability with mating parts.
Which tolerance class should I choose for probe pins and gauge sets?
Select tolerance classes aligned with your inspection requirements; for high‑precision tasks, sets produced to DIN 2269 or equivalent tolerance classes ensure micrometre‑level control and repeatability.
Can feeler gauges measure contact gaps in valve and engine work reliably?
Yes. Feeler gauges and precision feeler strips, supplied either as a fan or metre‑length rolls, allow accurate assessment of valve clearances and contact gaps down to micrometre increments.
How do limit gauges speed up in‑process inspection?
Limit gauges separate good from bad in a single, tactile operation, enabling rapid go/no‑go checks at the machine and reducing both inspection time and the likelihood of human interpretation errors.
Fragen zu diesen Produkten??
Mit mehr als 30 Jahren Erfahrung beraten wir Sie gerne persönlich.
Tel.: +49 2822 7131930
Mail: info@metav-werkzeuge.com