Precision gauge blocks and plug gauges for reliable dimensional control
Mechanical gauge blocks and plug gauges are essential for tactile verification of threads, bores and gap dimensions, providing fast, unambiguous go/no-go results that enhance process reliability and reduce scrap. Designed for industrial metalworking and toolmaking, these precision tools support incoming inspection and final quality checks by delivering traceable measurements in applications such as thread inspection, bore diameter testing and spacing checks. Manufactured from specially hardened, low-distortion alloys and fine-lapped for minimal measurement uncertainty, the range includes thread plug gauges, precision plug gauges and calibration gauge blocks to ensure long-term repeatability and wear resistance.
17.44mm Gauge Pin 50mm Length Workshop Version - Metav IndustryLine
Take advantage of the combination of ±0.002 mm repeatability, special steel construction and compact 50 mm length to secure reliable end‑measure references in the workshop; order the gauge pin directly via Metav Werkzeuge or consult our advisers for application advice. Gauge pin, single, 17.44 mm Ø, 50 mm length — Metav IndustryLine precision test pin The gauge pin, single, 17.44 mm diameter and 50 mm length is a workshop‑grade reference pin designed for end‑measure checks, fixture set‑up and quick interchange tests. Workshop‑grade design for daily use Diameter precisely 17.44 mm Tight tolerance ±0.002 mm Supplied in protective case Reliable reference for end‑measure checks The compact reference pin delivers repeatable measurements through a tight ±0.002 mm tolerance, making it suitable for final acceptance checks and quick go/no‑go verifications. A solid, dimensionally stable shaft of 17.44 mm diameter and a 50 mm overall length provides a consistent datum when setting up fixtures or verifying bore finishing. The measurable accuracy reduces rework and shortens inspection cycles by turning a complex verification into a straightforward mechanical reference. Built for workshop conditions with high durability Constructed from special steel, the pin resists everyday wear while maintaining form accuracy under typical workshop handling. The workshop‑grade finish balances hardness and surface quality to reduce the risk of marking mating components, while still offering robust service life. The compact length aids handling and storage, and the mass of 0.15 kg gives a reassuring feel during manual use without compromising portability. Simple integration and practical handling The single‑piece design enables straightforward use as a fixed reference in fixtures, a verification mandrel for bores or as a transfer standard for quick comparative measurements. Its clear nominal diameter and compact format make the pin compatible with common inspection setups and analogue gauges. The smooth shaft and precise ground geometry permit stable seating in bore checks and reduce wobble during gauging operations, improving repeatability of results between runs. Proven traceability for quality routines Marked and traceable identification supports organised inspection workflows. As a member of the Metav IndustryLine, the test pin is manufactured under controlled processes that prioritise dimensional stability and batch consistency. The combination of material choice and machining precision makes this item a dependable reference for workshop QC procedures and repeat checks where consistent end‑measure verification is required. For a reliable workshop reference, request the Metav IndustryLine gauge pin (SKU M323.H44) through Metav Werkzeuge; our consultants can advise on how this 17.44 mm reference pin matches existing inspection procedures. Technical data SKU: M323.H44 GTIN: 4061905070594 Label: Prüfstift, einzeln, 17,44 mm Länge 50 mm Dimensions & tolerances Diameter: 17.44 mm Length: 50 mm Tolerance: ±0.002 mm Weight: 0.15 kg Material & features Material: Special steel Workshop version Supplied individually Protective case for transport FAQ What is the usable length and diameter of the gauge pin? The gauge pin has a diameter of 17.44 mm and an overall length of 50 mm; the dimensions are intended for end‑measure and fixture referencing. What tolerance does the pin offer for precision checks? The reference pin is manufactured to a tolerance of ±0.002 mm, suitable for precise workshop verification and repeat checks. Is the material suited to regular workshop handling? Yes, the pin is made from special steel, providing a balance of hardness and durability for routine use in machining and inspection environments. Can the pin be used as a fixture datum or for bore checking? The single‑piece, ground shaft design permits stable seating in bores and use as a datum in fixture set‑ups, supporting consistent repeatability. Which SKU identifies this Metav IndustryLine test pin? This item is supplied as Metav IndustryLine SKU M323.H44 and is intended for workshop reference and end‑measure tasks. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
17.45mm Gauge Pin Single 50mm Length Workshop Version, 0.002mm Accuracy - Metav IndustryLine
Take advantage of the combination of workshop‑grade robustness, ±0.002 mm tolerance and a compact 50 mm working length for repeatable end‑measurements; the test pin arrives protected in a transport case. Order the test pin directly via Metav Werkzeuge or ask our consultants if needed. Test pin M323.H45 — Inspection pin, Ø 17.45 mm, 50 mm length (Metav IndustryLine) Test pin M323.H45 for precise end‑measurements and component checks in workshop and production environments. Workshop-grade construction Diameter 17.45 mm for end-measurements Tolerance ±0.002 mm for high repeatability Delivered in protective case Precise checks for repeatable results The M323.H45 is designed for high‑precision verification of external dimensions where minimal deviation matters. With a documented tolerance of ±0.002 mm, the pin provides a tight reference for go/no‑go checks and calibration routines, supporting consistent inspection results across batches. The compact 50 mm length and its defined Ø 17.45 mm profile make it particularly suitable for end‑measurements and plug‑gauging of small bores or mating parts, reducing uncertainty where tight fits are specified. This level of accuracy reduces rework and helps maintain quality targets in serial production. Durable workshop design that eases daily use Built in a workshop execution, the gauge pin combines a resilient special steel construction with a balanced weight for easy handling (approx. 0.15 kg). The surface finish and material choice ensure wear resistance in routine use while preserving dimensional stability. Supplied in a protective case for secure transport and storage, the component is ready for immediate integration into inspection trays or tool cabinets. The robust design reduces downtime for replacements and supports long service intervals in demanding shopfloor conditions. Integration into inspection workflows and suitability Classified in the micro range (measuring span 10–100 mm), this inspection pin fills the need for extremely compact, low‑deflection references used in fine mechanical and precision engineering tasks. The M323.H45 functions as a reliable end‑measure reference for gauge benches, fixture set‑ups and manual checks in toolrooms. Traceable identification (GTIN and SKU) facilitates inventory and quality documentation, while the simple geometry allows fast comparative checks without complex instrumentation. For tasks that require a repeatable mechanical standard rather than electronic sensing, this solid gauge provides clarity and speed in measurement routines. For production teams seeking a compact, high‑precision inspection standard, request the Metav IndustryLine test pin M323.H45 via Metav Werkzeuge; our specialists in Emmerich are available to advise on integration into existing quality processes. Technical Data Article number: M323.H45 GTIN: 4061905070600 Manufacturer: Metav IndustryLine Facts Length: 50 mm Diameter (measuring range): 17.45 mm Weight: 0.15 kg Tolerance: ±0.002 mm Special features Material: Special steel Workshop execution Delivered in protective case Category: Messstifte SKU: M323.H45 FAQ What is the intended application for this inspection pin? The test pin M323.H45 is intended for end‑measurement checks and comparative verification of small bores and mating parts in workshop and production settings. How precise is the M323.H45 for routine checks? The inspection pin is specified with a tolerance of ±0.002 mm, making it suitable for high‑accuracy comparative and go/no‑go checks. What material is used and how does that affect durability? Manufactured from special steel, the M323.H45 offers enhanced wear resistance and dimensional stability under normal workshop use. Is the test pin supplied ready for use and how is it packaged? The M323.H45 is delivered in a protective transport case, enabling immediate use and secure storage. Can the pin be integrated into existing fixture or gauge sets? Yes; the compact geometry and defined Ø 17.45 mm profile allow straightforward integration into fixture setups and manual gauge benches. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
17.46mm Gauge Pin 50mm Length Workshop Version - Metav IndustryLine
Take advantage of the combination of pinpoint accuracy, robust workshop design and compact dimensions for reliable in‑process inspection. The single test pin offers ±0.002 mm repeatability in a Ø 17.46 mm gauge body and a 50 mm shank for easy handling — order via Metav Werkzeuge or consult our specialists for application advice. Single test pin — Ø 17.46 mm / 50 mm length (Metav IndustryLine) The Single Test Pin, Ø 17.46 mm, length 50 mm is a workshop‑grade inspection pin designed for repeatable dimensional and form checks on small to medium components. High dimensional precision ±0.002 mm Diameter Ø 17.46 mm Length 50 mm workshop version Made from special steel Reliable precision for routine inspection The test pin delivers a very fine accuracy of ±0.002 mm, making it suitable for demanding go/no‑go checks and end‑dimension verification. This level of precision reduces rework and rejects by providing a dependable reference for comparative measurements. The compact diameter of 17.46 mm combines with a 50 mm shank to offer a stable contact surface while remaining easy to manoeuvre between fixtures. Where standard micrometric checks are required, this inspection pin acts as a quick numerical and tactile indicator, shortening setup times and supporting smoother production sequences. Robust design built for workshop conditions Constructed from special steel and specified as a workshop version, the pin tolerates the everyday stresses of a production environment without sacrificing measuring quality. The material choice ensures wear resistance at the contact face and preserves geometric integrity over repeated use. A modest mass and balanced geometry give the component good handling characteristics, while the workshop specification indicates practical durability rather than fragile laboratory construction. For operations that demand both longevity and consistent contact behaviour, this execution minimises downtime for replacements and supports continuous quality routines. Practical fit into quality workflows With a concise footprint and universal geometry, the pin integrates easily into fixed gauges, test rigs or handheld inspection procedures. It functions as a stable reference for comparative tests and can be used for checking bores, seating faces and end dimensions. The clear numeric specification and robust finish make documentation straightforward when recording inspection results or compiling process capability data. Where traceability is required, the identifiable SKU and GTIN facilitate stock control and audit trails, enabling straightforward inventory management within established quality systems. Contact Metav Werkzeuge for tailored application guidance on the Metav IndustryLine single test pin and to confirm availability for specific inspection setups Technical data Article number: M323.H46 GTIN: 4061905070617 Manufacturer: Metav IndustryLine Dimensions & tolerances Diameter: 17.46 mm Length: 50 mm Weight: 0.15 kg Measurement range min/max: 17.46 mm Accuracy: ±0.002 mm Materials & special features Material: Special steel Version: Workshop execution Category: Test pins FAQ What is the declared accuracy of this inspection pin? The inspection pin is specified with an accuracy of ±0.002 mm, which supports high‑precision comparative and end‑dimension checks for production use. Is the pin suitable for use in a gauge or fixture? Yes, the Metav IndustryLine single test pin (SKU M323.H46) is manufactured for workshop environments and is suitable for incorporation into fixed gauges and test fixtures. Which material is used for the pin and what does that mean for wear resistance? The pin is made from special steel; this offers improved wear resistance at contact faces and maintains dimensional stability over repeated measurements. Can the pin be used for checking bore diameters and end faces? The geometry and diameter of the pin make it appropriate for bore checks, seating faces and end‑dimension verification in routine inspection tasks. How is the product identified for inventory and traceability? The product carries the GTIN 4061905070617 and article number M323.H46 for clear identification in stock systems and quality records. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
17.47mm Gauge Pin 50mm Length Workshop Version, Special Steel - Metav IndustryLine
Benefit from reliable workshop precision, robust special‑steel construction and dimensional accuracy of ±0.002 mm; order the gauge pin M323.H47 directly via Metav Werkzeuge or contact our consultants for tailored advice. Gauge pin M323.H47 (17.47 mm Ø, 50 mm length) – Metav IndustryLine A gauge pin M323.H47 for fast end‑dimension checks, fixture set‑up and go/no‑go verification in workshop metrology. Workshop version for daily use Special steel construction Dimensional accuracy ±0.002 mm Nominal diameter 17.47 mm Accurate end‑dimension control that reduces rework The gauge pin delivers highly repeatable checks for bores, locating holes and alignment fixtures. With a nominal diameter of 17.47 mm and a declared tolerance of ±0.002 mm, it provides the dimensional certainty demanded in production and inspection loops. The 50 mm length balances reach and rigidity, allowing confident insertion into mating bores without excessive deflection. These characteristics translate into fewer measurement cycles, reduced rework and a measurable improvement in process throughput for machining and assembly operations. Workshop‑ready design for efficient inspection routines Manufactured in special steel and specified as a workshop version, the component is engineered for frequent handling and quick checks at the bench or on the machine. The compact mass (0.15 kg) and ergonomic dimensions make it easy to position in jigs or test fixtures, supporting rapid throughput during batch checks. The robust surface treatment maintains running fit and concentricity over many cycles, enabling technicians to maintain flow in busy production environments while keeping quality checks concise and reliable. Traceability and durable build for long‑term use The component is traceable and clearly identifiable for inventory and QA processes, helping to integrate it into existing inspection regimes. The construction from special steel and the compact geometry minimise wear and preserve gauge form over time, which supports consistent measurement results and lowers lifetime cost of ownership. Supplied as a single gauge pin intended for routine verification tasks, it fits into modular inspection sets or can be used standalone for targeted go/no‑go operations in fixture set‑up and maintenance tasks. Contact Metav Werkzeuge in Emmerich to secure the Metav IndustryLine gauge pin M323.H47 or to request personalised technical advice by e‑mail or phone Technical Data Article number: M323.H47 GTIN: 4061905070624 Weight: 0.15 kg Facts Diameter: 17.47 mm Length: 50 mm Tolerance: ±0.002 mm Special features Material: special steel Workshop execution Category: Gauge pins (Messstifte) eClass: 21170231 FAQ What is the intended use of this gauge pin? The gauge pin is designed for end‑dimension checks, locating hole verification and fixture set‑up; the Metav IndustryLine M323.H47 is suitable for routine workshop inspection tasks. How precise is the measurement fit of the pin? The nominal diameter is 17.47 mm with a dimensional tolerance of ±0.002 mm, giving the M323.H47 the accuracy required for reliable go/no‑go and fit checks. Which material is used for this pin and why does it matter? The pin is made from special steel, chosen for wear resistance and dimensional stability to maintain form and concentricity under repeated use. Can the pin be integrated into existing inspection jigs? Yes; the 50 mm length and standard diameter make the pin easy to incorporate into fixtures, test plates and modular inspection sets for quick checks. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
17.48mm Gauge Pin 50mm Length Workshop Version, Special Steel - Metav IndustryLine
Take advantage of the combination of precise dimensional control, robust workshop design and compact handling for consistent end‑dimension verification; order the gauge pin directly via Metav Werkzeuge or ask our consultants if needed. Test pin M323.H48 — Gauge pin Ø 17.48 mm, 50 mm length (Metav IndustryLine) The Test pin M323.H48 is a single gauge pin designed for end‑dimension inspection and assembly verification in workshop environments, combining compact geometry with industrial tolerancing for repeatable checks Workshop version for robust everyday use Diameter 17.48 mm for end‑dimension checks Length 50 mm with ±0.002 mm accuracy Supplied in protective transport case Consistent measurement accuracy for production control The M323.H48 gauge pin delivers ±0.002 mm positional variation, making it suitable where tight tolerances matter in incoming inspection and final assembly. As a precision gauge pin with a nominal 17.48 mm diameter and 50 mm shaft length, it converts a simple plug‑fit into a quantifiable check that reduces rework and speeds decision‑making on the shop floor. The compact mass and rigid geometry ensure stable seating in fixtures, which supports automated and manual checking processes alike. Designed to endure workshop routines Built as a workshop version, this probe uses special steel chosen for a balance of hardness and toughness, offering wear resistance under frequent use. The component’s low mass (about 0.15 kg) and short footprint help to avoid bending moments during handling while enabling fast exchange in gauges and jigs. Delivered in a protective transport case, the pin arrives ready for safe storage and transit, lowering the risk of transport damage and preserving the measurement face for longer service life. Practical applications and operational benefits This single gauge pin is aimed at end‑dimension controls, go/no‑go verifications and assembly alignment tasks in machining and mechanical assembly environments. Compatibility with standard holding fixtures and the simple geometry make integration straightforward, while the tight tolerance supports traceable quality records in production reports. The compact form factor helps maintain throughput in high‑mix operations without sacrificing measurement confidence. For procurement and technical advice on Metav IndustryLine gauge pins, contact Metav Werkzeuge for precise availability, delivery options and suitability for specific inspection tasks. Technical Data Article number: M323.H48 GTIN: 4061905070631 SKU: M323.H48 Description: Test pin, single, 17.48 mm, length 50 mm Material: Special steel Weight: 0.15 kg Length: 50 mm Facts Diameter: 17.48 mm Measuring range min/max: 17.48 mm Accuracy: ±0.002 mm Mass: 0.15 kg Special features Workshop version Supplied in protective transport case Category: Gauge pins Application: End‑dimension checks FAQ What material is the pin made from? The pin is manufactured from special steel; the M323.H48 gauge pin combines hardness and toughness for extended service life. Is the pin suitable for end‑dimension verification? Yes, the test pin is intended for end‑dimension checks and assembly verification where a precise plug‑fit is required. Does the delivery include protective packaging? The gauge pin is supplied in a protective transport case to prevent damage during storage and shipment. What accuracy can be expected from this gauge pin? The M323.H48 is specified with an accuracy of ±0.002 mm, making it appropriate for fine tolerance inspections. Can this pin be used in standard holding fixtures? The compact geometry and standard diameter allow straightforward integration into common fixtures and jigs for production checks. Metav IndustryLine: Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
17.49mm Gauge Pin, 50mm Length, Workshop Version, Special Steel, Supplied in Case - Metav IndustryLine
The combination of tight tolerance and a rigid 50 mm length ensures reliable, repeatable end‑measurements in workshop use; the ±0.002 mm accuracy and special steel construction support consistent quality control. Order the gauge pin via Metav Werkzeuge or consult their specialists for batch and application advice. Gauge pin M323.H49 — 17.49 mm diameter, 50 mm length (Metav IndustryLine) A gauge pin, single, 17.49 mm, 50 mm length engineered for precise end‑measurements and routine inspection tasks in workshop environments Workshop execution, robust and serviceable Diameter 17.49 mm for end‑measurement fits High repeatability with ±0.002 mm accuracy Made from special steel for wear resistance Reliable tolerance for fast, traceable inspections The gauge pin achieves a measured accuracy of ±0.002 mm, which translates into dependable repeatability for pass/fail checks and short‑run quality control. Such tight tolerance reduces uncertainty during go/no‑go evaluations and helps avoid unnecessary rework by ensuring that acceptance limits are checked with a stable reference. In practice, the high level of precision shortens inspection time per part and raises confidence in measurement results, making the pin suitable for critical end‑measurement tasks where small deviations matter. Durable workshop design for everyday handling Built as a workshop execution, the inspection pin combines a compact 50 mm shank with wear‑resistant special steel to resist abrasion in repeated use. The 50 mm length provides sufficient rigidity for direct insertion into fixtures and for hand‑held checks, while the modest mass (approx. 0.15 kg) keeps handling comfortable during serial inspections. This construction minimises deformation and maintains dimensional stability over many cycles, so uptime in production and service intervals are improved without complex maintenance requirements. Easy integration into inspection routines and traceability The item is supplied as a single inspection pin (SKU M323.H49) and is identified for logistical traceability by GTIN 4061905070648. As a compact gauge pin for end‑measurements, it integrates into existing jigs and checking fixtures and can be used as a reference master for dimensional comparisons. The straightforward geometry simplifies seating and repeatable alignment, while the workshop‑grade finish reduces the need for protective handling. For procurement and continuity of supply, Metav IndustryLine offers rapid fulfilment from its Emmerich quality hub. Contact Metav Werkzeuge to confirm fitment for specific fixtures or to arrange batch supply of M323.H49 directly from Emmerich Product details SKU: M323.H49 GTIN: 4061905070648 Description: Gauge pin, single, 17.49 mm diameter, 50 mm length Brand: Metav IndustryLine Measurements & accuracy Diameter: 17.49 mm Length: 50 mm Tolerance / accuracy: ±0.002 mm Weight: 0.15 kg Materials & features Material: Special steel Version: Workshop execution Application: End‑measurements / inspection Category: Gauge pins FAQ What level of accuracy does this gauge pin provide? The gauge pin is specified with an accuracy of ±0.002 mm, giving the M323.H49 the repeatability required for tight end‑measurement checks. Is the product supplied as a single item or in sets? This article is supplied as a single gauge pin; the product designation indicates an individual inspection pin for direct use in fixtures or hand checks. Which materials is the pin made from and how does that affect wear? Manufactured from special steel, the inspection pin offers improved wear resistance compared with untreated steels, extending service life under normal workshop conditions. Can this pin be used for fixture masters and gauge blocks? Yes — the rigid 50 mm length and precise diameter make the pin suitable as a reference in fixtures and for comparative measurements against master references. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
17.4mm Gauge Pin 50mm Length Workshop Version - Metav IndustryLine
Take advantage of a compact measuring reference that combines precise dimensional control (17.4 mm) with a tight repeatability of ±0.002 mm in a robust workshop configuration; the single test pin comes in a protective transport case and is available through Metav Werkzeuge — order the test pin directly via Metav Werkzeuge or ask our consultants if needed Test pin, single — 17.4 mm diameter, 50 mm length (Metav IndustryLine) Test pin, single — 17.4 mm diameter, 50 mm length for end‑measure verification and workshop inspection tasks in precision metrology Workshop version for daily industrial use Precision diameter 17.4 mm with ±0.002 mm accuracy Durable special steel construction for long service life Supplied in protective transport case Precision that stabilises process control The compact measuring reference offers a 17.4 mm nominal diameter with a verified ±0.002 mm variation, making it suitable where narrow tolerances are decisive. Presented as a single, dedicated pin, it serves as a fixed gauge for end‑measure and limit checks, reducing measurement scatter and enabling faster decision‑making on the shop floor. The combination of clear nominal size and low manufacturing dispersion supports consistent part validation and helps lower reject rates during series production. Built for routine workshop reliability Designed as a workshop version, the pin is manufactured from special steel selected for dimensional stability under normal use. With a 50 mm length and a mass around 0.15 kg, the component is easy to handle and resists incidental knocks common in busy production areas. The compact design simplifies storage and integration into existing jigging or inspection fixtures. Supplied in a protective transport case, the item arrives ready for safe storage and reduces the risk of transit damage. Simple integration and clear traceability The single test pin functions as a straightforward reference for end‑measure operations, comparative gauging and final inspection routines. Its straightforward geometry minimises setup time and makes it compatible with bench fixtures and optical comparators where a fixed, repeatable datum is required. Traceability is supported by the clear labelling and product identifiers supplied with each unit, which simplify inventory control and process documentation in quality management systems. For secure supply and application guidance for the Metav IndustryLine test pin, contact Metav Werkzeuge in Emmerich for local availability and technical consultation Technical data Article number: M323.H40 GTIN: 4061905069581 Manufacturer: Metav IndustryLine / Metav Werkzeuge GmbH Core dimensions & accuracy Diameter: 17.4 mm Length: 50 mm Accuracy: ±0.002 mm Weight: 0.15 kg Special features Material: special steel Delivery condition: single pin in protective transport case Design: workshop execution (robustised for daily use) Category: test pins FAQ What applications is this test pin suitable for? The test pin, single — 17.4 mm diameter, 50 mm length is intended for end‑measure verification, comparative gauging and workshop inspection where a fixed dimensional reference is required. Is the material corrosion‑resistant? The pin is manufactured from special steel, chosen for dimensional stability and wear resistance; surface finish and corrosion performance depend on the specific workshop environment and storage routine. How precise is the diameter control on this pin? Diameter control is stated at 17.4 mm with a manufacturing variation of ±0.002 mm, making the component suitable for close‑tolerance checks in routine quality control. Can this pin be integrated into fixtures or comparators? Yes. The 50 mm length and cylindrical geometry allow easy mounting in inspection fixtures or use alongside optical comparators as a repeatable reference element. Is the product supplied with individual identification? Each test pin is provided as a single unit with product identification to aid traceability in inspection records for the Metav IndustryLine test pin (M323.H40). Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
17.5 mm Gauge Pin, Single, 50 mm Length, Workshop Version - Metav IndustryLine
Benefit from the combination of workshop‑grade construction, special steel durability and a manufacturing tolerance of ±0.002 mm for consistent end‑dimension checks; order the test pin directly via Metav Werkzeuge or consult our advisors for application guidance. M323.H50 test pin — Workshop gauge pin, Ø 17.5 mm, 50 mm length (Metav IndustryLine) The M323.H50 test pin is a workshop‑grade gauge pin designed for reliable end‑dimension verification and alignment tasks in metalworking environments. Workshop‑grade construction Diameter Ø 17.5 mm Manufacturing tolerance ±0.002 mm Delivered in protective case Repeatable measurements for end‑dimension control A stable gauge must provide predictable results under repeated use; this test pin delivers by virtue of a tight ±0.002 mm manufacturing tolerance, which reduces measurement scatter during comparative checks and fixture verification. The short, rigid geometry supports repeatability for end‑dimension inspections and alignment tasks, making it suitable where consistent reference diameters are required. For quality control routines, the pin’s specification helps maintain process capability and reduces rework stemming from gauging variability. Robust workshop design and material benefits Constructed from special steel, the pin is engineered for daily workshop handling and the mechanical stresses of insertion and removal from bores and fixtures. The 50 mm length and compact mass (0.15 kg) balance accessibility with stability: long enough to engage clearances and short enough to resist bending under normal use. The workshop‑grade finish eases cleaning and routine care, while the included protective case ensures safe transport and storage between measurement cycles, preserving the reference geometry. Practical handling and typical applications Classified within the micro range for gauge pins (10–100 mm), this product addresses fine to medium‑sized gauging needs such as end‑dimension checks, plug verification and positioning aids in jigs and fixtures. The single‑unit supply simplifies inventory for specific diameters and supports retrofit or replacement in existing test setups. Lightweight handling and clear dimensional marking speed up cyclical checks on production lines, while the inherent design reduces operator handling time and contributes to efficient measurement workflows. Contact Metav Werkzeuge for tailored advice on integrating the M323.H50 test pin into existing gauging systems or to request a quotation from our Emmerich‑based team. Technical data Article number: M323.H50 GTIN: 4061905070655 Material: Special steel Length: 50 mm Diameter: 17.5 mm Weight: 0.15 kg Numbers / Core technical data Tolerance: ±0.002 mm Length: 50 mm Diameter: 17.5 mm Weight: 0.15 kg Special features Workshop version Delivered in protective case Single unit delivery Category: Gauge pin (Messstifte) Intended for end‑dimension checks FAQ What is the primary use of this gauge pin? The M323.H50 test pin from Metav IndustryLine is intended for end‑dimension checks, plug verification and alignment tasks in jigs and fixtures where a defined reference diameter is required. What accuracy does the pin offer? Manufactured to a tolerance of ±0.002 mm, the M323.H50 provides tight dimensional consistency for repeatable comparative measurements and fixture checks. What material is the pin made from and is it durable? The M323.H50 is made from special steel and finished for workshop use, giving it robustness suited to frequent insertion and removal in typical metalworking environments. Is the pin supplied with protective packaging? Yes, the M323.H50 is supplied as a single unit and delivered in a protective case to safeguard the reference surface during transport and storage. Which applications suit this diameter and length? A diameter of 17.5 mm and a length of 50 mm make the M323.H50 appropriate for medium‑sized bore checks, alignment aids and fixture reference points within standard workshop and production settings. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
17.51mm Gauge Pin, Single, 50mm Length, Workshop Version - Metav IndustryLine
A compact workshop-grade gauge pin with a 17.51 mm nominal diameter and ±0.002 mm tolerance delivers reproducible end measurements; combine the robustness of special steel with a compact 50 mm length for efficient inspection workflows. Order the gauge pin directly via Metav Werkzeuge or ask the consultants for further configuration. Gauge pin, single — 17.51 mm nominal diameter, 50 mm length (Metav IndustryLine) A single gauge pin designed for precise end‑dimension checks in workshop and inspection environments, supplied in a workshop execution for routine measuring tasks. Workshop execution for regular use Nominal diameter 17.51 mm 50 mm overall length Tolerance ±0.002 mm Precision where small tolerances make a measurable difference The gauge pin is manufactured to a ±0.002 mm tolerance, which translates into consistently tight dimensional control during inspection and assembly. For routine end‑dimension verification this level of precision reduces uncertainty in pass/fail decisions and shortens verification cycles. Presented in the micro range (nominal diameter 17.51 mm), the pin is particularly suited to fine mechanical tasks where small deviations would otherwise affect fit or function. Built to withstand workshop handling while remaining compact Constructed from special steel, the pin balances surface integrity with dimensional stability required during repeated use. The 50 mm overall length gives a secure gripping allowance without adding unnecessary overhang, which helps maintain repeatability in handheld or fixture-mounted checks. As a workshop version, the design accepts routine handling and integration into inspection benches while offering a compact reference element for small components. Integrates simply into inspection processes and jigs As an individual gauge pin, this item functions as a fixed reference for end‑measurements and can be combined with pin blocks or locating fixtures to accelerate throughput. The defined end dimension and tight tolerance improve traceability in batch checks and reduce downstream rework by catching deviations early. Using a standard nominal size such as 17.51 mm helps maintain compatibility with existing gauge sets and inspection jigs. Reliability supported by an experienced precision partner Sourcing this gauge pin from Metav IndustryLine links the component to a supplier network that emphasises consistent supply and workshop usability. Metav’s position as a precision partner means routine items are selected to deliver practical benefits on the shop floor: dependable reference values, straightforward handling and the assurance of a recognised distribution and logistics setup. Contact Metav Werkzeuge for a specification check or to discuss how this Metav IndustryLine gauge pin can be incorporated into existing inspection routines — call +49 2822 7131930 or email info@metav-werkzeuge.com Technical data SKU: M323.H51 GTIN: 4061905070662 Brand: Metav IndustryLine Numbers Diameter: 17.51 mm Length: 50 mm Tolerance: ±0.002 mm Weight: 0.15 kg Special features Material: Special steel Version: Workshop execution Application: End measurement ECLASS: 21170231 FAQ What is the nominal diameter of this gauge pin? The gauge pin has a nominal diameter of 17.51 mm; the Metav IndustryLine single gauge pin (SKU M323.H51) is made for precise diameter reference. Which tolerance class does the pin meet? The pin is manufactured to a tolerance of ±0.002 mm, making it suitable for tight end‑dimension verification in workshop inspection routines. What material is used for the pin? This Metav IndustryLine gauge pin is produced from special steel, chosen for its dimensional stability under normal workshop conditions. Is the pin suitable for fine mechanical and small‑part inspection? Yes; with its nominal diameter and compact length, the pin is aimed at micro range applications and fine mechanical inspection tasks. Can this single gauge pin be combined with other pins or fixtures? The pin is intended as a standalone reference element that can be integrated into pin blocks and inspection jigs for routine measurement setups. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
17.52mm Gauge Pin 50mm Length Workshop Finish - Metav IndustryLine
Take advantage of a precise combination of high dimensional accuracy and workshop-ready robustness for reliable end-size verification. The compact form and tight tolerance support consistent assembly checks and fixture alignment; order the gauge pin directly via Metav Werkzeuge or consult the specialists if additional data is required. Gauge pin M323.H52 — Single gauge pin Ø 17.52 mm, 50 mm length (Metav IndustryLine) The Gauge pin Ø 17.52 mm, length 50 mm is a workshop-grade precision pin for end‑size checks, fixture alignment and repeatable gauging tasks. Workshop version for robust use Diameter Ø 17.52 mm Tolerance ±0.002 mm Supplied in transport case Reliable end-size verification for consistent production The M323.H52 is engineered for end‑size measurements where reproducibility is essential: a nominal diameter of 17.52 mm combined with a declared tolerance of ±0.002 mm gives a clear quantitative basis for pass/fail decisions on bores and fit checks. In practical terms, the specified tolerance corresponds to micrometre‑level control that keeps mounting features within assembly limits; this removes guesswork during in‑process inspection and reduces rework. The compact geometry and defined contact diameter are ideal for establishing reference points in jigs and gauges, while the clear numerical specification allows direct comparison with inspection protocols. Built for workshop durability and straightforward handling Constructed from special steel and offered in a workshop execution, the test pin balances hardness and toughness so it withstands routine handling and contact with machined surfaces. The 50 mm length provides a stable gripping area without excessive overhang, and the item’s modest weight (0.15 kg) ensures easy manipulation during setup. Delivery in a transport case protects the critical measuring face in transit and storage, keeping the gauge pin ready for immediate use. The robust design reduces the need for frequent replacement and supports a reliable shop‑floor workflow. Practical integration into measuring routines and fixture set‑up As a single, precisely defined gauge element, this test pin simplifies common metrology tasks: checking bore diameters, aligning fixtures, verifying plug fits and setting reference limits for comparative measurements. The clear numeric data and hardened contact face make it straightforward to include this element in quality documentation or to use it as a master pin for go/no‑go comparisons. Its compact format is particularly suitable where space is limited but dimensional certainty is required, supporting both production control and maintenance routines with minimal setup time. For workshop‑grade precision and uncomplicated procurement of the Metav IndustryLine M323.H52, request the gauge pin from Metav Werkzeuge — procurement and technical advice available from Emmerich via info@metav-werkzeuge.com or +49 2822 7131930 Technical data Article number: M323.H52 GTIN: 4061905070679 Designation: Gauge pin, single, Ø 17.52 mm, length 50 mm Brand: Metav IndustryLine Weight: 0.15 kg Data Diameter: 17.52 mm Length: 50 mm Tolerance: ±0.002 mm Measuring range (min/max): 17.52 mm / 17.52 mm Special features Workshop execution Supplied in transport case for transport and protection Single piece delivery Intended for end‑size checks and fixture alignment Robust special steel construction FAQ What level of dimensional accuracy does this gauge pin provide? The declared tolerance for the M323.H52 gauge pin is ±0.002 mm, which supports micrometre‑level decisions in routine shop inspection and ensures consistent end‑size evaluation. Is the delivery specified as calibrated to an accredited standard? The product data does not indicate delivery with an accredited calibration certificate; calibration status is not specified for this item. What is the gauge pin made from and how durable is it? The M323.H52 is manufactured from special steel and presented in a workshop version designed to withstand regular contact with machined surfaces and handling typical for production environments. Which applications suit this gauge pin best? This gauge pin is intended for end‑size checks, fixture alignment, plug‑fit verification and use as a master reference in production and maintenance settings Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
17.53mm Gauge Pin 50mm Length Workshop Version, Special Steel - Metav IndustryLine
Take advantage of the combination of exact dimensional control, workshop‑proven durability and simple handling to streamline fixture checks and end‑measure tasks; order the part directly via Metav Werkzeuge or consult our technical advisers for integration guidance. Gauge pin, single, Ø 17.53 mm, length 50 mm (M323.H53) — Metav IndustryLine The gauge pin, single, Ø 17.53 mm, length 50 mm serves as a stable reference diameter for end‑measure verification and fixture set‑up in production and inspection environments. Workshop execution for industrial environments Exact diameter 17.53 mm for precision fits Tight tolerance ±0.002 mm for reliable reference 50 mm working length suitable for fixture checks Precision that supports repeatable inspection results The reference dowel delivers a consistent reference diameter that reduces measurement uncertainty during go/no‑go verification and alignment checks. With a stated tolerance of ±0.002 mm, the part provides a verifiable limit for pass/fail assessments and helps to standardise dimensional checks across batches. The carefully controlled diameter ensures repeatability when used as a master pin for plug gauges or as a setting standard in mechanical fixtures, which in turn reduces rework and rejects in serial production. Durable design for intensive workshop use Engineered in a workshop execution, the dowel is manufactured from special steel selected for robust handling and repeated engagement in jigs and gauges. At a nominal length of 50 mm and a compact mass, the component is easy to seat and remove from fixtures while retaining the stiffness required for accurate contact measurement. The construction is aimed at operators and inspectors who demand a reliable reference that tolerates daily use without compromising dimensional integrity. Practical applications and integration benefits This reference pin excels in end‑measure verification, fixture set‑up, and alignment of mating parts where a precise nominal diameter is required. The geometry makes the component suitable for use as a locating dowel in assembly fixtures or as a setting master for plug‑type gauges and alignment tools. By providing a stable reference, the part helps to accelerate set‑up times and improves interchangeability between components and stations, supporting consistent production throughput. Contact Metav Werkzeuge today to discuss how the Metav IndustryLine gauge pin M323.H53 can be integrated into existing inspection routines or production fixtures Technical data Article number: M323.H53 GTIN: 4061905070686 Category: Messstifte Facts Diameter: 17.53 mm Length: 50 mm Tolerance: ±0.002 mm Weight: 0.15 kg Special features Material: special steel Workshop execution Single piece reference pin Intended for end‑measure and fixture checks FAQ What tolerance does the gauge pin offer? The gauge pin is specified with a tolerance of ±0.002 mm, providing a tight reference limit for go/no‑go checks and comparative measurements with master gauges; this applies to the Metav IndustryLine gauge pin M323.H53. Which material is the pin made from? The component is manufactured from special steel, chosen for durability in workshop and inspection applications and intended for repeated seating in fixtures. What are the typical applications for this reference pin? Common uses include end‑measure verification, fixture set‑up, alignment tasks and use as a master for plug gauges in production and quality control processes. Is a calibration certificate supplied with the part? Product data does not indicate a supplied calibration certificate; for traceable calibration options or certificates, refer to Metav Werkzeuge’s calibration services. What are the core dimensions and identifier for ordering? Core dimensions are Ø 17.53 mm and length 50 mm; ordering reference is M323.H53 (GTIN 4061905070686). Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
17.54mm Gauge Pin Length 50mm Workshop Finish - Metav IndustryLine
High-precision workshop gauge pin made from special steel with a tolerance of ±0.002 mm and a nominal diameter of 17.54 mm, supplied ready for safe transport in a protective case; order the gauge pin directly via Metav Werkzeuge or ask our consultants if needed Gauge pin M323.H54 — Workshop test pin, Ø 17.54 mm, 50 mm length (Metav IndustryLine) The gauge pin M323.H54 is a workshop-grade test pin intended for accurate end measurements and fit checks; its compact dimensions and tight tolerance make it suitable for routine inspection tasks in a production or maintenance environment Workshop-grade precision component Nominal diameter 17.54 mm, length 50 mm Tolerance ±0.002 mm for repeatable fits Precision where it matters: reliable end-measurement results A solid gauge pin with a nominal diameter of 17.54 mm and a length of 50 mm provides a consistently reproducible reference for final-size checks and assembly verifications. The specified tolerance of ±0.002 mm ensures that plug or hole fits can be assessed with confidence, reducing reject rates and rework. In industrial metrology contexts this kind of test pin is classified in the Micro range (10–100 mm), which combines compact handling with the stiffness needed for repeatable contact measurements. The inert surface of the special steel minimises wear over many cycles, prolonging the service life and maintaining dimensional stability during routine use. Built for the workshop: protection and handling advantages Designed as a workshop execution component, the test pin arrives in a protective transport case to prevent damage during storage and transit. This organised packaging supports safe handling on the shop floor and keeps the reference surface free from nicks that would compromise accuracy. At 0.15 kg mass the component is easy to position by hand or fit into inspection fixtures, while the nominal geometry allows straightforward insertion into gauges, sockets or mating parts. Robust material selection and workshop-focused finishing combine to offer a maintenance-friendly tool that withstands frequent use without complex care procedures. Practical integration: applications and efficiency gains This style of test pin is commonly used for end measurements, assembly checks and go/no‑go verifications where a precise cylindrical reference is required. Using a dedicated gauge pin reduces measurement time compared with time‑consuming alternative methods and supports a smoother production flow by delivering fast pass/fail decisions. Traceable identification (SKU M323.H54, GTIN 4061905071416) simplifies inventory management and quality documentation. For workshops seeking to standardise inspection steps, the pin’s repeatability and fit stability enable tighter process control and clearer acceptance criteria for incoming or outgoing parts. Contact Metav Werkzeuge today for delivery details on the M323.H54 workshop gauge pin and individual advice on integrating it into existing inspection routines Technical data Article number: M323.H54 GTIN: 4061905071416 SKU: M323.H54 Dimensions & tolerances Nominal diameter: 17.54 mm Length: 50 mm Tolerance: ±0.002 mm Weight: 0.15 kg Design & features Material: special steel Workshop execution Supplied in protective transport case Category: gauge pin Typical use: end measurements / fit verification FAQ What is the nominal diameter and length of this gauge pin? The gauge pin has a nominal diameter of 17.54 mm and a length of 50 mm, suitable for routine end-measurement tasks. What accuracy can be expected from the M323.H54 gauge pin? The M323.H54 is specified with a tolerance of ±0.002 mm, delivering repeatable fit checks for production and inspection applications. Is the test pin delivered ready for use and protected during transport? Yes; the test pin is supplied in a protective transport case appropriate for workshop handling, keeping the reference surface safe until use. Which applications are typical for this type of gauge pin? Typical uses include end measurements, assembly fit verification and go/no‑go checks where a precise cylindrical reference is required. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
17.55mm Precision Gauge Pin 50mm Length Workshop Version, Special Steel - Metav IndustryLine
Compact accuracy and dependable shop use combine in this workshop‑grade gauge pin: 17.55 mm nominal diameter, 50 mm overall length and a narrow ±0.002 mm tolerance make it suitable for repeatable end‑measurements and go/no‑go checks. Supplied in a protective transport case, the component supports efficient inspection routines; order via Metav Werkzeuge or consult our specialists for application advice. Gauge pin M323.H55 – single test pin, Ø 17.55 mm, length 50 mm (Metav IndustryLine) Gauge pin M323.H55 is a workshop‑grade single test pin in special steel, designed for precise end‑measurement and bore checking in metalworking and assembly tasks. Workshop version for daily shop use Precision diameter 17.55 mm ±0.002 mm Length 50 mm, made from special steel Repeatable inspection with micrometre-level tolerance The pin is manufactured to a nominal diameter of 17.55 mm with a verified tolerance of ±0.002 mm, offering performance that supports tight inspection criteria and reduces subjective judgement during bore verification. Such precision means fewer reworks and a more predictable quality flow when used as a reference or master pin for end‑measurement applications. The narrow tolerance also allows integration into existing gauging stacks or fixture checks where a consistent reference diameter is required. Built for the workshop: robust form and protective packaging Produced in special steel and specified as a workshop execution, the test pin resists everyday handling while maintaining measurement stability. The 50 mm overall length provides sufficient engagement for many bore depths without excess overhang, improving handling and control in one‑hand inspection tasks. Delivery in a protective transport case ensures the pin reaches the workbench with minimal risk of transit damage, preserving surface integrity and dimensional reliability for immediate use. Practical benefits for production and quality workflows As a single test pin intended for end‑measurements, the component simplifies quick go/no‑go controls and spot checks on assemblies and mating parts. The compact form and predictable behaviour of the material reduce inspection time per part, contributing to throughput improvements in small‑batch production. Compatibility with common holding fixtures and pin blocks makes it easy to add this reference piece to existing measurement routines, supporting faster decision points and consistent documentation in quality records. For reliable end‑measurement in the workshop, choose the Metav IndustryLine gauge pin M323.H55 and contact Metav Werkzeuge GmbH in Emmerich for tailored technical guidance by e‑mail or phone Technical data Article number: M323.H55 GTIN: 4061905071423 Label: Test pin, single, 17.55 mm length 50 mm Manufacturer: Metav IndustryLine Facts Nominal diameter: 17.55 mm Overall length: 50 mm Tolerance / accuracy: ±0.002 mm Weight: 0.15 kg Special features Material: special steel Workshop execution Supplied in transport case Intended use: end‑measurements / bore checking FAQ What level of dimensional accuracy does this pin provide? The gauge pin M323.H55 is specified with an accuracy of ±0.002 mm, making it suitable for fine inspection and repeatable end‑measurement tasks. Is the pin suitable for heavy daily use in a workshop environment? Yes — the workshop execution and special steel construction give the pin the robustness required for regular use on the shop floor. How is the product delivered to ensure protection? The M323.H55 is supplied in a protective transport case to prevent handling and transit damage and to maintain surface and dimensional integrity. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
17.56mm Gauge Pin 50mm Length Workshop Version, Special Steel - Metav IndustryLine
The combination of precise diameter control (17.56 mm), tight tolerance (±0.002 mm) and a robust 50 mm length makes this inspection pin a reliable tool for reproducible end‑measure checks; order the test pin directly via Metav Werkzeuge or consult our advisors for application support. Test pin, single — 17.56 mm diameter, 50 mm length (Metav IndustryLine) The Test pin, single, 17.56 mm diameter, 50 mm length is a precision inspection pin designed for end‑measure verification and gauge fixtures in workshop and production metrology Precision diameter 17.56 mm Tolerance ±0.002 mm Compact 50 mm length for confined checks Workshop version made from special steel Reproducible end‑measure results for production Consistent metrology reduces rework and speeds up set‑ups. The inspection pin offers a defined diameter of 17.56 mm with a verified tolerance of ±0.002 mm, which translates into repeatable fit checks and reliable pass/fail decisions on the shop floor. By using a dedicated gauge pin rather than an improvised tool, measurement uncertainty is minimised and fixture validation becomes straightforward. The documented accuracy supports traceable inspections and reduces the risk of scrap due to ambiguous fits. Built for workshop durability and simple handling A workshop‑specification construction in special steel provides wear resistance and stable geometry during frequent insertion and removal cycles. At a mass of 0.15 kg and a length of 50 mm, the pin combines manageable handling with sufficient stiffness for day‑to‑day verification tasks. The compact form factor is particularly useful where access is restricted or where multiple pins are stored in gauge sets. The robust finish and solid material choice help to maintain the precision diameter over many inspection cycles, which saves maintenance time and ensures consistent production quality. Practical integration and traceability in production workflows This single inspection pin (SKU M323.H56) is intended for end‑dimension checks, gauge blocks and fixture validation in machining and assembly processes. The clear specification — 17.56 mm diameter, 50 mm length, and ±0.002 mm tolerance — allows easy selection when matching pins to bore gauges or plug gauges. As a labelled inspection component, it supports inventory control and audit trails within quality systems. The product is suitable for repetitive quality checks where a defined reference diameter improves decision speed and reduces operator variability. Contact Metav Werkzeuge to request the M323.H56 test pin or to discuss how its 17.56 mm precision can be integrated into existing gauge fixtures — call +49 2822 7131930 or email info@metav-werkzeuge.com Technical Data Article number: M323.H56 GTIN: 4061905071430 Brand: Metav IndustryLine Weight: 0.15 kg Facts Diameter: 17.56 mm Length: 50 mm Tolerance: ±0.002 mm Measuring range (max): 17.56 mm Special features Workshop version Material: special steel Single test pin for end‑measure checks ECLASS: 21170231 FAQ What is the dimensional tolerance of this inspection pin? The inspection pin is manufactured to a tolerance of ±0.002 mm, making the M323.H56 suited to precise end‑measure verifications. Which material is used for the pin? The M323.H56 is produced from special steel in a workshop version designed for daily use and good wear resistance. What are the key dimensions supplied? This single test pin has a diameter of 17.56 mm and a length of 50 mm; mass is 0.15 kg; SKU M323.H56. Where is this pin typically used? The pin is intended for end‑dimension checks, gauge fixtures and quick pass/fail verifications in machining, assembly and quality control processes. Is the M323.H56 suitable for repeated shop‑floor checks? Yes — the workshop construction and material selection make the M323.H56 appropriate for frequent use while maintaining its dimensional stability. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
17.57mm Gauge Pin Length 50mm Workshop Version - Metav IndustryLine
Take advantage of precise dimensional control, robust workshop construction and a compact form factor for reliable end‑measurements; order the gauge pin directly via Metav Werkzeuge or consult our specialists for application advice. Gauge pin M323.H57 — 17.57 mm diameter, 50 mm length (Workshop grade) A workshop-grade gauge pin for end measurements and fit checks, supplied as a single inspection pin Workshop-grade construction Diameter 17.57 mm, length 50 mm Tolerance ±0.002 mm for tight fits Made from special steel for durability Consistent inspection results through robust workshop design The single inspection pin is engineered as a workshop grade measuring element, combining a special steel body with machining tolerances that support high repeatability in everyday quality control. The robust finish and compact geometry reduce the risk of damage during handling and mounting in gauge blocks or fixtures, which means fewer interruptions to inspection routines and greater uptime on the shop floor. The construction emphasises longevity and stable contact geometry, benefitting repetitive dimensional verification tasks. Precise end‑measurement and fit verification for small diameters With a nominal diameter of 17.57 mm and a length of 50 mm, the pin provides a clear reference for end‑measurements and go/no‑go checks in tight tolerances. The declared accuracy of ±0.002 mm addresses fine inspection requirements where surface contact and concentricity are critical; this tolerance ensures reliable assessment of bore fits, seating surfaces and transitional diameters. The small form factor makes the element suitable for integration into checking jigs and comparative gauges where space is limited. Compact format for micro‑scale checks and fixture testing The product sits in the compact measurement segment, ideal for fine mechanical and workshop applications that demand manageable handling without sacrificing metrological quality. Its compact format supports quick positioning in fixtures and fast manual transfers between stations, improving inspection throughput. The single‑piece design is particularly suited to end‑face inspections and go/no‑go plug tests for components with small diameters, delivering a practical balance between reach and rigidity for routine quality assurance. For supply or tailored advice on using the Metav IndustryLine gauge pin M323.H57 in measurement fixtures, contact Metav Werkzeuge for local delivery from Emmerich and expert product guidance Technical data SKU: M323.H57 GTIN: 4061905071447 Label: Prüfstift, einzeln, 17,57 mm Länge 50 mm Eclass: 21170231 Facts Diameter: 17.57 mm Length: 50 mm Weight: 0.15 kg Accuracy: ±0.002 mm Special features Material: Special steel Workshop execution (Werkstatt‑Ausführung) Single inspection pin for end measurements FAQ What are the exact dimensions of this inspection pin? The inspection pin M323.H57 has a nominal diameter of 17.57 mm and a length of 50 mm; the SKU is M323.H57. What tolerance does the pin offer for fit testing? The pin is specified with a tolerance of ±0.002 mm, suitable for precise fit verification and repeatable end‑measurements. What material is used for the pin? The gauge pin is made from special steel, chosen for mechanical stability and wear resistance in workshop use. Which applications suit this workshop‑grade inspection pin? This workshop execution is suited to end‑face checks, bore fit tests and fixture integration where a compact, robust reference pin is required; it is particularly useful for small‑diameter components and routine quality control. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
17.58mm Gauge Pin 50mm Length Workshop Version, Special Steel ±0.002mm - Metav IndustryLine
The combination of workshop‑grade durability, a precisely ground diameter of 17.58 mm and a verified tolerance of ±0.002 mm delivers consistent end‑of‑line verification for production parts; order the gauge pin directly via Metav Werkzeuge or consult our specialists for application advice. Gauge pin M323.H58 — single test pin, diameter 17.58 mm, 50 mm length (Metav IndustryLine) A gauge pin M323.H58 engineered for accurate go/no‑go checks, pin sizing and dimensional verification in workshop inspection and assembly operations. Workshop‑grade special steel construction Precisely ground diameter 17.58 mm Tolerance ±0.002 mm for tight checks Compact 50 mm length for versatile probing Reliable accuracy for routine inspection The pin is designed to provide consistent measuring results in repetitive inspection tasks. With a nominal diameter of 17.58 mm and a verified ±0.002 mm deviation, this test pin supports clear pass/fail decisions during manufacturing control. The combination of a ground diameter and tight tolerance reduces ambiguity in fits and clearances, helping to prevent downstream rework. As a precision tool for component verification, it integrates well into standard inspection benches and fixture checks, improving throughput through dependable sizing. Built to withstand workshop conditions Constructed from special steel in a workshop version finish, the pin offers resistance to abrasion and frequent handling typical of a production environment. The 50 mm length provides sufficient engagement for many locating and gauging tasks while keeping the tool easy to handle; the listed weight of 0.15 kg reflects a compact, manoeuvrable design that does not fatally increase fixture inertia. Heat treatment and surface grinding deliver long service life and stable contact geometry, so wear‑related measurement drift is minimised and maintenance intervals are extended. Integrates into quality processes with clear traceability As a single gauge pin for dimensional checks, the M323.H58 suits assembly verification, contractor handovers and end‑mass inspection where repeatability is essential. The straightforward geometry enables rapid substitution in gauge sets and fixtures, while the clear SKU and GTIN permit unambiguous inventory management and traceability. Used alongside calibrated reference standards and documented inspection routines, the pin supports reproducible measurement results and helps maintain quality records across production batches. Contact Metav Werkzeuge for specification matching, availability from our Emmerich warehouse and tailored advice on incorporating the Metav IndustryLine gauge pin into existing inspection routines Technical data Article number / SKU: M323.H58 GTIN: 4061905071454 Brand: Metav IndustryLine Label: Prüfstift, einzeln, 17,58 mm Länge 50 mm Facts Diameter: 17.58 mm Length: 50 mm Tolerance: ±0.002 mm Weight: 0.15 kg Special features Material: special steel Workshop version Single gauge pin Category: Messstifte FAQ What accuracy can be expected from this gauge pin? The M323.H58 gauge pin is specified with a tolerance of ±0.002 mm, making it suitable for fine dimensional checks and tight fit verification. Which material is used for the pin and why does it matter? This test pin is made from special steel; the material choice gives improved wear resistance and dimensional stability under routine workshop handling for the Metav IndustryLine pin. Is the gauge pin suitable for fixture and assembly checks? Yes, the 50 mm length and compact mass of the M323.H58 make it well suited for locating, fixture checks and assembly verification where a robust, repeatable pin is required. How is the product identified for stock and traceability? Identification is provided by the SKU M323.H58 and GTIN 4061905071454, which support clear inventory control and traceability in production and quality records. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
17.59mm Gauge Pin 50mm Length Workshop Version, Special Steel in Case - Metav IndustryLine
The combination of a 17.59 mm diameter and a tight ±0.002 mm tolerance delivers dependable end‑measure control for workshop inspection routines; the 50 mm length and special steel construction support repeatable seating and long service life. Order the part directly via Metav Werkzeuge or contact the consultants for application advice and fast supply from Emmerich. Metav IndustryLine gauge pin M323.H59 — 17.59 mm diameter, 50 mm length The gauge pin M323.H59 is a single precision test pin for end‑measure checks and dimensional reference work in workshop and production inspection. Precision tolerance ±0.002 mm Diameter 17.59 mm, length 50 mm Made from special steel Workshop execution, robust design Ensure conformity with a high‑precision reference A tight tolerance of ±0.002 mm means the pin functions as a reliable reference for end‑measure inspections and pass/fail checks where small deviations matter. The marked accuracy aids traceable decision‑making in quality workflows, reducing the risk of rework and shipment of non‑conforming parts. Using a defined gauge diameter such as 17.59 mm helps to standardise inspection steps and maintain consistent measurement conditions across repeated checks. Built for repeatability and durable handling Constructed from special steel and specified at 50 mm length, the pin is designed for robust everyday use in a workshop environment. Its mass and dimensions (weight 0.15 kg) support stable seating in fixtures and measuring benches, which improves repeatability during manual handling. The workshop execution prioritises practical resilience so that dimensional checks remain consistent over time, contributing to lower measurement uncertainty in routine quality control. Easy identification and integration into inspection processes Delivered as a single test pin, the item integrates straightforwardly into gauge sets, plug gauges or fixture checks where an exact end‑measure reference is required. The product is traceable by SKU and GTIN for inventory and procurement purposes, supporting orderly stock management and clear replacement planning. Its specification targets end‑measure applications, helping to align incoming inspection, in‑process checks and final acceptance testing with a compact, high‑accuracy reference component. Specify the Metav IndustryLine gauge pin M323.H59 for robust end‑measure standards — contact Metav Werkzeuge in Emmerich for tailored technical advice and reliable delivery from stock Technical data Article number: M323.H59 GTIN: 4061905071461 Label: Prüfstift, einzeln, 17,59 mm Länge 50 mm Manufacturer: Metav IndustryLine Facts Diameter: 17.59 mm Length: 50 mm Tolerance: ±0.002 mm Weight: 0.15 kg Special features Material: Special steel Workshop execution Single piece delivery Story trigger: endmasse FAQ What tolerance does this gauge pin provide? The gauge pin M323.H59 is specified with a tolerance of ±0.002 mm, making it suitable for high‑precision end‑measure checks in workshop inspection routines. What material is used for the test pin? This test pin is made from special steel, a choice that supports durability and consistent seating during repeated measurements. For which inspection tasks is the pin suitable? The pin is intended for end‑measure and dimensional reference checks, where a defined 17.59 mm diameter and stable length assist in verifying component conformity. How is the item supplied and identified? The product is supplied as a single test pin and can be identified by SKU M323.H59 and GTIN 4061905071461 for procurement and inventory management. Can this pin be added to existing gauge blocks or fixtures? Yes; as a compact, high‑accuracy reference element the pin is suitable for integration into gauge assemblies and fixture checks to standardise measurement routines. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
17.61mm Gauge Pin, Single, 50mm Length, Workshop Version - Metav IndustryLine
Take advantage of the combination of industrial accuracy, a compact micro range and a hardened working finish for reliable end-dimension checks. The precise diameter and short length support fast in-process control and repeatable inspection routines; order the gauge pin directly via Metav Werkzeuge or consult our technical team for specification matching. Gauge pin M323.H61 – Gauge pin Ø 17.61 mm, 50 mm length (Metav IndustryLine) A compact gauge pin, the M323.H61 is intended for precise end-dimension verification in workshop and inspection environments. High accuracy ±0.002 mm Diameter exactly 17.61 mm 50 mm overall length Workshop version in special steel Precision designed for critical inspection tasks The M323.H61 gauge pin is built for repeatable end-dimension checks where tight tolerances matter. With a stated accuracy of ±0.002 mm, the pin suits applications that require fine control over final sizes in small bores and fitted parts. The compact diameter of 17.61 mm and a 50 mm shank provide a stable contact length that reduces measurement scatter compared with longer, more flexible gauges. In practical terms, this means fewer rejections due to measurement variability and a consistent basis for in-process acceptance criteria. Robust workshop execution for everyday use Delivered as a workshop version, the test pin is made from special steel and finished to withstand routine handling. The material choice and processing ensure surface integrity and wear resistance during repeated engagement with component seats and gauging fixtures. The short overall length keeps the gauge stiff under manual use, improving handling in bench or fixture work and making it less prone to bending-induced error during insertion and removal. Traceability and handling that fit the workflow The pin is supplied ready for integration into inspection routines; its compact size simplifies storage and handling while enabling rapid exchange between setups. The design supports quick bench checks and slotting into gauge blocks, jigs or dedicated holders without elaborate fixturing. A clear product code (M323.H61) and machine-readable GTIN help to keep inventory and calibration records synchronised with shop-floor documentation and quality systems. Practical advantages in the measurement chain For suppliers and shops that prioritise a predictable measurement chain, this gauge pin offers a straightforward solution: precise nominal diameter, defined contact length and an industrial finish that tolerates frequent use. The construction minimises the need for additional handling precautions and makes the component suitable for serial checking, final assembly inspection or quick verification during set-up processes. For supply, calibration options and logistics, contact Metav Werkzeuge in Emmerich via info@metav-werkzeuge.com or +49 2822 7131930 to arrange delivery of the Metav IndustryLine gauge pin M323.H61 and discuss compatibility with existing gauges and fixtures. Technical Data Article number: M323.H61 GTIN: 4061905071973 Label: Prüfstift, einzeln, 17,61 mm Länge 50 mm Manufacturer: Metav IndustryLine Facts Diameter: 17.61 mm Length: 50 mm Accuracy: ±0.002 mm Weight: 0.15 kg Special features Material: special steel Workshop version Compact micro-range component Supplied for immediate inspection use FAQ What tolerance does the gauge pin guarantee? The gauge pin M323.H61 is specified with an accuracy of ±0.002 mm, making it suitable for fine inspection tasks requiring tight dimensional control. Is the pin suitable for repeated shop‑floor use? Yes, the workshop execution and special steel construction of the M323.H61 are intended for frequent use in inspection and assembly environments. How should the gauge pin be stored to preserve accuracy? Store the gauge pin in a dry, dust‑free location and keep it in its protective packaging between uses to avoid nicks and contamination that could affect the measuring surface. Can this pin be integrated into fixture or jig checks? The compact diameter and 50 mm length of the M323.H61 make it straightforward to mount in holders or use as a reference in bespoke gauging fixtures. Is the product traceable for quality records? Yes; the M323.H61 is delivered with product identification (SKU and GTIN) to support inventory and quality documentation. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
17.62mm Gauge Pin, Single 50mm Length, Workshop Version - Metav IndustryLine
Take advantage of the combination of precise dimensional control, robust workshop construction and traceable identification for reliable end‑measurement tasks — order the gauge pin directly via Metav Werkzeuge or contact our consultants for tailored advice. Gauge pin M323.H62, 17.62 mm Ø, 50 mm length (Metav IndustryLine) The gauge pin M323.H62 is a precision test pin designed for end‑measurement and serial inspection in workshop and production environments. Workshop version with robust finish Diameter controlled to 17.62 mm tolerance 50 mm length for compact fixture use Accuracy ±0.002 mm for repeatable checks Faster, traceable inspection through true precision A compact inspection tool reduces cycle times in quality control. The gauge pin delivers precision down to ±0.002 mm, which shortens decision loops in serial testing and minimises rework. Its nominal size of 17.62 mm and 50 mm length make it suitable for plug‑gauge checks and end‑measurement of mating parts; the tight tolerance ensures that pass/fail decisions are based on measurable, reproducible criteria rather than approximation. Where consistent measurement results are a production KPI, the instrument contributes directly to throughput and scrap reduction. Durable workshop construction for everyday use Built as a workshop version, the pin withstands frequent handling and repeated insertion cycles. Manufactured from special steel, the component offers a mix of surface hardness and dimensional stability that keeps wear rates low under regular use. The single‑unit configuration supports straightforward inventorying and makes the part ideal for small batches or targeted replacement in inspection jigs. Clear material choice and solid construction translate into low lifetime cost and dependable service in routine metrology tasks. Simple integration into inspection workflows The test pin supports common inspection tasks such as end‑measurement and functional gauging within fixtures and checking devices. Its compact geometry allows it to be mounted or used free‑hand where space is restricted, and the discrete size is compatible with many standard plug‑gauge holders and test rigs. Traceable identifiers, including the SKU and GTIN recorded with each item, facilitate quality records and traceability across production lots and audits. The tool’s straightforward specification eases communication between workshop personnel and quality engineers when defining acceptance criteria. Choose the Metav IndustryLine gauge pin M323.H62 for robust workshop inspection and clear measurement results — contact Metav Werkzeuge for purchasing or technical guidance via info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: M323.H62 GTIN: 4061905071980 Brand: Metav IndustryLine Label: Gauge pin, single, 17.62 mm, length 50 mm Facts Diameter: 17.62 mm Length: 50 mm Accuracy: ±0.002 mm Weight: 0.15 kg Special features Workshop version Single unit delivery Material: special steel Intended for end‑measurement FAQ What is the intended application of this gauge pin? The gauge pin M323.H62 is intended for end‑measurement and plug‑gauge checks in workshop and production inspection routines. How precise is the M323.H62 in routine use? This Metav IndustryLine test pin offers an accuracy of ±0.002 mm, suitable for tight go/no‑go and dimensional checks. Is the pin supplied as a single unit or in sets? The product is supplied as a single unit; the item is described as a single test pin and is suitable for targeted replacement or use in single‑station fixtures. Which material is used for the pin and why does it matter? The pin is made from special steel, chosen for wear resistance and dimensional stability to ensure long service life under repeated inspection cycles. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
17.63mm Gauge Pin 50mm Length Workshop Version - Metav IndustryLine
Take advantage of precise workshop inspection with a robust 17.63 mm diameter pin, 50 mm usable length and a verified positional accuracy of ±0.002 mm for dependable end‑measure readings; order the gauge pin directly from Metav Werkzeuge or consult our product specialists for application advice. Gauge pin, single, 17.63 mm, 50 mm length — Metav IndustryLine The Gauge pin, single, 17.63 mm, 50 mm length is a hardened inspection pin for end‑measure and bore checking, designed for routine workshop inspection and component control. Workshop‑grade special steel construction Diameter 17.63 mm for end‑measure checks 50 mm length for secure insertion depth Supplied in a protective transport case Reliable geometry for repeatable end‑measurement This inspection pin delivers a consistent reference for end‑measure tasks and bore gauging where repeatability matters. The calibrated nominal diameter of 17.63 mm provides a clear go/no‑go datum for fit checks and end‑length verification. Owing to the fine positional tolerance of ±0.002 mm, the pin is suitable for high‑accuracy routine checks in maintenance benches and inspection stations, reducing rework and measurement uncertainty. Material choice and mechanical durability explained Manufactured from special steel, the component combines surface hardness with resistance to wear in regular workshop use. The 50 mm overall length gives sufficient engagement for most insertion checks while retaining good handling and stability. The workshop design balances toughness with manageable mass, so the pin withstands repeated insertion cycles without premature deformation, supporting longer intervals between replacements. Practical handling and storage for everyday use As a single‑item inspection solution, the pin is optimised for quick tool‑room tasks and portable inspection kits. The protective transport case ensures safe handling and prevents surface damage that would otherwise affect measurement integrity. The product’s practical design shortens set‑up time during quality control rounds and keeps inspection routines efficient and predictable. Traceability and identification for professional workflows Clear identification and traceability are provided through the manufacturer SKU and GTIN, aiding inventory control and process documentation. The compact format integrates easily into existing inspection sets and provides a stable reference for end‑measure procedures in production, assembly and maintenance environments, supporting documented quality workflows. For application matching or batch purchases contact Metav Werkzeuge in Emmerich for tailored advice and order processing via +49 2822 7131930 or info@metav-werkzeuge.com Technical data Article number: M323.H63 GTIN: 4061905071997 Manufacturer: Metav IndustryLine Facts Diameter: 17.63 mm Overall length: 50 mm Tolerance / positional accuracy: ±0.002 mm Weight: 0.15 kg Special features Material: Special steel Workshop execution Single item (individual pin) Supplied in protective transport case FAQ What is the intended use of this inspection pin? The inspection pin is intended for end‑measure and bore checking as a reliable reference for insertion and fit verifications in workshop inspection tasks. Which materials is the pin suitable for measuring against? The pin itself is made from special steel and is used to check component bores and mating parts made from typical workshop materials such as steel and aluminium. How precise are the measurements achieved with this pin? The pin is produced to a positional accuracy of ±0.002 mm, providing high repeatability for routine inspection and go/no‑go assessments. Is this item traceable for quality documentation? Yes, the product carries the GTIN 4061905071997 and article number M323.H63 for inventory and traceability purposes. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
17.64mm Test Pin 50mm Length Workshop Version - Metav IndustryLine
Benefit from workshop-grade construction, special steel material and a tight ±0.002 mm tolerance for reproducible end-measure checks; these characteristics support reliable in-process inspection and consistent batch acceptance. Order the gauge pin directly via Metav Werkzeuge or consult the advisors if further specification is required. Gauge pin, single, 17.64 mm — 50 mm length (Metav IndustryLine) The gauge pin, single, 17.64 mm, length 50 mm is a workshop-grade inspection pin designed for precise end-measure and go/no-go checks in production and assembly environments. Workshop version for industrial use Precision diameter 17.64 mm Length 50 mm for consistent reach High accuracy ±0.002 mm Stable dimensional reference for routine checks The inspection pin serves as a compact, stable dimensional reference where repeatability matters. Constructed from special steel, the probe maintains shape under regular handling and contact, supporting reproducible end-measure outcomes with a verified positional variation of ±0.002 mm. Such tolerance makes the component suitable for precise acceptance checks on shafts, bores and mating parts where small deviations can affect assembly performance. Designed for efficient workflow and handling At 50 mm length and approximately 0.15 kg mass, this probe balances reach and manoeuvrability to fit bench and jig environments without adding unnecessary bulk. The 50 mm length gives access to recessed features while the compact form supports fast insertion and withdrawal during sampling routines, helping to keep inspection cycles short and throughput steady. The workshop execution emphasises durability for frequent use on the shop floor. Integrates with inspection processes and fixtures As a standard-dimension gauge pin, the component is intended for straightforward integration into existing inspection jigs and fixture arrays, simplifying checks during first-article inspection and routine quality control. Using a fixed-dimension probe reduces setup complexity and supports consistent measurement logs, which contributes to traceable manufacturing decisions and fewer rework cycles. The combination of a clearly defined diameter and tight tolerance aids compatibility with calibrated test equipment and established metrology workflows. For a precision partner that democratises accuracy across workshops, contact Metav Werkzeuge to source the Metav IndustryLine gauge pin M323.H64 and secure consistent inspection performance for production checks. Technical data Article number: M323.H64 GTIN: 4061905072000 Label: Prüfstift, einzeln, 17,64 mm Länge 50 mm Category: Messstifte Facts Diameter: 17.64 mm Length: 50 mm Weight: 0.15 kg Tolerance / variation: ±0.002 mm Special features Material: Special steel Workshop execution Image asset available FAQ What are the nominal dimensions of the gauge pin? The gauge pin is specified with a diameter of 17.64 mm and an overall length of 50 mm; it is listed as gauge pin, single, 17.64 mm, length 50 mm (Metav IndustryLine, SKU M323.H64). What level of accuracy does this inspection pin provide? The inspection pin is specified with a positional variation of ±0.002 mm, making it suitable for precise end-measure and acceptance checks in workshop environments. Which applications are appropriate for this probe? The probe is intended for end-measure checks, go/no-go inspections and routine dimensional verification on shafts, bores and mating components within production and assembly workflows. Is the material suitable for repeated shop-floor use? The pin is made from special steel and supplied in a workshop-grade execution, designed to withstand frequent handling typical of industrial inspection routines. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
17.65mm Gauge Pin, Single, 50mm Length, Workshop Version, Special Steel, ±0.002mm, Supplied in Case - Metav IndustryLine
Take advantage of ±0.002 mm tolerance and a 17.65 mm fixed diameter in a workshop‑grade gauge pin supplied in a transport case; this combination ensures repeatable end‑measure checks and low handling risk. Order the gauge pin directly via Metav Werkzeuge or ask our consultants if needed. Gauge pin, single, 17.65 mm Ø – 50 mm length (Metav IndustryLine) The gauge pin, single, 17.65 mm Ø, 50 mm length is a compact workshop‑grade test pin for reliable end‑measure verification and assembly checks in machining and inspection routines. Workshop‑grade execution, robust finish Diameter 17.65 mm, length 50 mm Tolerance ±0.002 mm for precise checks Precision that secures process stability The pin delivers measurable improvement in repeatability thanks to its ±0.002 mm manufacturing tolerance, which translates into fewer measurement‑related rejects and more predictable assembly outcomes. As a fixed‑diameter reference element, the component provides an objective datum for bore checks and end‑measure verifications; operators and quality engineers benefit from a clearly defined gauge value rather than relying on inferred fits. The technical certainty of the 17.65 mm reference reduces rework and supports consistent quality documentation. Robust design for everyday workshop use Manufactured from special steel, the probe is configured as a workshop‑grade tool intended to withstand frequent handling and the rigours of production environments. The 50 mm usable length combines reach with stiffness, helping to avoid bending errors during insertion and extraction. Delivery in a protective transport case preserves surface condition and dimensional integrity during storage and transit, making the item practical for mobile inspection tasks or shared tool cabinets without additional packaging work. Practical application in inspection and assembly workflows As a single gauge pin, this test pin suits quick go/no‑go verifications, alignment tasks and end‑measure validation in fixtures and assemblies where a precise, fixed reference is required. The pin integrates easily into existing checking procedures and can serve as a repeatable datum for comparative measurements or as a reference when setting up jigs. The Metav IndustryLine provenance ensures compatibility with an extensive range of workshop metrology accessories, simplifying procurement and replacement planning for quality teams familiar with modular inspection components. For dependable end‑measure precision from Metav IndustryLine, contact Metav Werkzeuge in Emmerich for availability and expert advice on integrating this gauge pin into inspection workflows Technical Data Article number: M323.H65 GTIN: 4061905069765 Brand: Metav IndustryLine Facts Diameter: 17.65 mm Length: 50 mm Tolerance / accuracy: ±0.002 mm Weight: 0.15 kg Special features Material: Special steel Workshop execution Supplied in transport case Single piece gauge pin FAQ What tolerance can be expected from this gauge pin? The gauge pin is manufactured to a tolerance of ±0.002 mm, providing high repeatability for end‑measure checks with the Metav IndustryLine single pin (SKU M323.H65). Is the pin suitable for routine bore checks and alignment tasks? Yes, the fixed 17.65 mm diameter and 50 mm usable length make the pin appropriate for quick bore verifications, alignment and assembly datum checks in workshop environments. How is the pin protected during transport and storage? The single gauge pin is supplied in a protective transport case to preserve surface condition and dimensional integrity during storage or mobile use. What materials is the pin made from and what does that mean for durability? Constructed from special steel, the pin is designed for workshop durability and repeated handling, offering resistance to wear in standard inspection and setup tasks. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
17.66mm Gauge Pin 50mm Length Workshop Version - Metav IndustryLine
Take advantage of a compact inspection solution that combines high dimensional accuracy (±0.002 mm) with robust special‑steel construction and a standard 50 mm measuring shank; ideal for reliable end measurements in production and quality control. Order the item directly via Metav Werkzeuge or consult the Metav specialists for application advice. Gauge pin M323.H66 — single test pin, ø17.66 mm, 50 mm length (Metav IndustryLine) A single precision gauge pin designed for end‑measurement and fit inspection in workshop and production metrology. Single gauge pin ø17.66 mm, length 50 mm High accuracy ±0.002 mm tolerance Machined from special steel for durability Supplied individually for straightforward inspection Consistent dimensional control for quality assurance The compact test pin delivers reproducible end measurements thanks to a tight manufacturing tolerance of ±0.002 mm. This level of accuracy supports rapid go/no‑go checks and sampling inspections in a serial production environment, reducing the need for repeated rework. The pin’s nominal diameter ø17.66 mm and 50 mm measuring length make it suitable for checking bore seats, plug fits and end‑mass inspections where a stable reference is essential. Using a defined reference pin like this streamlines measurement routines and speeds up acceptance checks without compromising traceability. Durable construction for repeated use under workshop conditions Manufactured from special steel, the test pin resists wear and maintains dimensional integrity across frequent handling. The workshop design emphasises a balance between surface hardness and machinability so that the contact face remains intact under typical inspection cycles. The component’s measured mass and solid construction contribute to stable seating in fixtures and minimise deviations caused by incidental deformation. As a hardened and precisely machined testing element, it provides long‑term service life and predictable performance for day‑to‑day metrology tasks. Easy integration into inspection workflows and tool sets Delivered as an individual item, the pin is straightforward to insert into existing gauge sets, fixture blocks or handheld test assemblies. The simple geometry allows rapid visual and tactile verification of fits and clear pass/fail assessment without complex adjustment. The compact format also supports portable inspection routines on the shop floor, enabling fast checks close to the machining process and therefore reducing downtime. For inventory and logistics, the item is identified by its SKU M323.H66 and GTIN for streamlined ordering and stock management. Practical benefits for production and maintenance teams A precision test pin of this specification reduces measurement uncertainty during assembly checks and contributes to consistent part interchangeability. By standardising on defined reference elements with ±0.002 mm accuracy, quality teams can document measurement outcomes more reliably and make faster decisions about process adjustments. The robust material choice and straightforward form factor mean fewer replacements and lower lifecycle handling costs compared with ad hoc or improvised gauges. Contact Metav Werkzeuge for application guidance and secure procurement of Metav IndustryLine measurement elements—phone +49 2822 7131930 or eMail info@metav-werkzeuge.com Technical data SKU: M323.H66 GTIN: 4061905069772 Label: Gauge pin, single, ø17.66 mm, length 50 mm Manufacturer: Metav IndustryLine Core specifications Diameter: 17.66 mm Length: 50 mm Tolerance: ±0.002 mm Weight: 0.15 kg Features Single test pin (delivered individually) Workshop version (Werkstatt‑Ausführung) Material: special steel Intended for end‑measurement and fit inspection FAQ What is the intended use of this gauge pin? The pin is intended for end‑measurement and fit inspection tasks; the gauge pin M323.H66 is suited to checking bore seats and plug fits where a precise reference diameter is required. How accurate is the pin and what does that mean in practice? Manufactured to ±0.002 mm, the pin provides tight dimensional control for production sampling and go/no‑go verification, reducing ambiguity in pass/fail decisions. What material is used and how does it affect durability? The component is made from special steel, chosen for wear resistance and stability so that the test face retains its dimensions over repeated use. Can the pin be used in handheld checks or only in fixtures? The compact form and 50 mm shank allow use both in fixture blocks and in portable, handheld inspection routines for immediate on‑machine checks. Is the item traceable for inventory and procurement? Yes; the pin is listed under SKU M323.H66 with GTIN 4061905069772 for straightforward ordering and stock control. Metav IndustryLine: Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
17.67mm Test Pin, Single, 50mm Length, Special Steel, Workshop Version - Metav IndustryLine
Take advantage of the combination of workshop-ready robustness, sub-micron repeatability and compact dimensions for reliable end‑measure checks. Order the gage pin directly via Metav Werkzeuge or consult our specialists for rapid procurement from Emmerich. Gauge pin M323.H67 — single, Ø 17.67 mm, 50 mm length (Metav IndustryLine) The gauge pin M323.H67 is a precision test pin for end‑measurement tasks and inspection jigs in workshop and production environments. Workshop design for daily use Tight tolerance of ±0.002 mm Made from special steel for durability Compact 50 mm length for confined fixtures Consistent dimensional control for inspection tasks The M323.H67 serves as a compact reference element when checking final dimensions and fits. The Ø 17.67 mm nominal diameter combined with the tolerance of ±0.002 mm provides a measurable trust level for go/no‑go decisions and fixture setting. Using a hardened reference pin minimises wear at contact points so that repeatability remains high even under frequent use. This enables workplaces to reduce rework and maintain assembly tolerances with confidence. Robust materials and workshop readiness Constructed from special steel, the pin combines surface hardness with resistance to deformation during routine handling. The 50 mm length offers sufficient engagement for many end‑measure applications without demanding excessive clamping space. The workshop version specification indicates a build tuned to practical use: easy to handle, robust against impacts and compatible with common inspection setups in machining and metalworking shops. Practical integration into measurement routines As a single test pin, this component is straightforward to install in gauges, nests and comparator fixtures. Its compact profile simplifies placement in tight assemblies and enables precise localisation when aligning mating parts. Where frequent verification is required, the element’s geometry supports rapid substitution and minimal adjustment effort, contributing to shorter inspection cycles and consistent quality checks. Clear advantages for production and toolrooms The combination of a small footprint and precision grading supports faster setup times on jigs and gauging equipment. Because the pin holds a narrow tolerance band, it is suitable for final control points and dimensional verification where a definitive pass/fail result is needed. The overall usability reduces the dependence on complex measuring procedures and streamlines routine controls in small‑ to medium‑series production. Documentation and traceability for procurement The product arrives labelled with its SKU M323.H67 and GTIN for inventory control and traceability. Weight and dimensions are recorded to simplify storage planning and handling. For organisations building a standardised set of reference elements, these identifiers ease cataloguing and replacement ordering from the central supplier. For dependable end‑measure checks, specify the Metav IndustryLine gauge pin M323.H67 and contact Metav Werkzeuge for personalised advice and swift supply from our Emmerich facility. Technical data SKU: M323.H67 GTIN: 4061905070075 Facts Diameter: 17.67 mm Length: 50 mm Tolerance: ±0.002 mm Weight: 0.15 kg Special features Material: Special steel Workshop version Single gauge pin for end‑measure checks Category: Gauge pins FAQ What is the primary use of this gauge pin? The gauge pin is intended for end‑measure checks and fixture reference points in inspection and assembly operations, providing a precise physical reference for go/no‑go decisions. Is the tolerance suitable for precision assembly tasks? Yes. With a declared deviation of ±0.002 mm, the M323.H67 meets tight repeatability requirements for many precision assembly and inspection workflows. Which material is the pin made from and why does that matter? The pin is made from special steel, chosen for surface hardness and resistance to wear, ensuring long‑term dimensional stability under regular contact. Can this pin be used in confined fixtures and jigs? Its 50 mm length and compact diameter make it particularly suited to confined mounting positions and narrow gauge nests where space is limited. How can the M323.H67 be ordered or referenced for stock control? Order using SKU M323.H67 or GTIN 4061905070075; these identifiers support straightforward procurement and inventory management. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
Fast, tactile checks where electronics are impractical
Gauges and test pins provide unequivocal go/no-go results for threads, bores, gaps and radii without relying on electronics. The range covers plug gauges and ring gauges for internal and external threads, feeler gauges and precision feeler strips for micro‑gap assessment, plus probe pins and measuring pins for tactile diameter and pitch checks.
How these tools work in the production environment
Mechanical gauges operate as direct reference standards: a plug gauge or ring gauge verifies conformity to thread profiles and mating ability, while limit gauges separate accept from reject in a single step. Test pins are used to tactilely measure small bore diameters, centre‑to‑centre distances and radii. Manufactured from hardened gauge steel or ceramic and often precision lapped, these instruments deliver immediate physical results that are ideal for incoming inspection, machine‑side checks and final control.
Measurable benefits that affect production performance
- Reduced scrap and rework through rapid, unambiguous pass/fail assessment.
- Increased repeatability thanks to very low measurement uncertainty and fine lapping.
- Lower downtime: quick checks at the machine save cycle time and reduce setup periods.
- Durable construction with high wear resistance from specialised, low‑distortion alloys.
- Versatile delivery formats: individual gauges, organised sets in wooden cases or metre‑length feeler rolls compliant with DIN 2269.
Why Metav is the practical choice for precision supplies
Metav combines decades of expertise with a broad warehouse and quality filtering from Emmerich. As a precision partner for industry, craft and trade, Metav supplies a comprehensive selection of gauges and test pins alongside complementary tools such as precision calipers and setting rings. With over 48,000 customers and a catalogue exceeding 250,000 items, Metav is positioned to supply reliably, reduce vendor complexity and support traceable quality control to national standards.
Summary
Gauges and test pins are indispensable for dependable, repeatable quality assurance where tactile, mechanical verification is preferred. Choose these plug gauges, ring gauges, feeler strips and probe pins when immediate, robust measurement decisions are required on the shop floor.
FAQ
What materials are gauges and test pins typically made from?
Gauges and test pins are usually manufactured from hardened gauge steel for durability and wear resistance; ceramic variants are available where thermal stability and minimal wear are critical.
How do thread gauges ensure mating capability?
Thread plug gauges and ring gauges check flank diameters and thread form against standards, providing a clear go/no‑go verdict that confirms pairability with mating parts.
Which tolerance class should I choose for probe pins and gauge sets?
Select tolerance classes aligned with your inspection requirements; for high‑precision tasks, sets produced to DIN 2269 or equivalent tolerance classes ensure micrometre‑level control and repeatability.
Can feeler gauges measure contact gaps in valve and engine work reliably?
Yes. Feeler gauges and precision feeler strips, supplied either as a fan or metre‑length rolls, allow accurate assessment of valve clearances and contact gaps down to micrometre increments.
How do limit gauges speed up in‑process inspection?
Limit gauges separate good from bad in a single, tactile operation, enabling rapid go/no‑go checks at the machine and reducing both inspection time and the likelihood of human interpretation errors.
Fragen zu diesen Produkten??
Mit mehr als 30 Jahren Erfahrung beraten wir Sie gerne persönlich.
Tel.: +49 2822 7131930
Mail: info@metav-werkzeuge.com