Precision gauge blocks and plug gauges for reliable dimensional control
Mechanical gauge blocks and plug gauges are essential for tactile verification of threads, bores and gap dimensions, providing fast, unambiguous go/no-go results that enhance process reliability and reduce scrap. Designed for industrial metalworking and toolmaking, these precision tools support incoming inspection and final quality checks by delivering traceable measurements in applications such as thread inspection, bore diameter testing and spacing checks. Manufactured from specially hardened, low-distortion alloys and fine-lapped for minimal measurement uncertainty, the range includes thread plug gauges, precision plug gauges and calibration gauge blocks to ensure long-term repeatability and wear resistance.
17.92mm Gauge Pin 50mm Length Workshop Finish - Metav IndustryLine
Take advantage of a compact, shop-ready measuring pin with 17.92 mm diameter and an industrial ±0.002 mm tolerance for reliable end‑dimension checks; order the gauge pin directly via Metav Werkzeuge or consult our specialists for application support. Gauge pin M323.H92 — Test pin (17.92 mm Ø, 50 mm length) by Metav IndustryLine A single gauge pin 17.92 mm, length 50 mm designed for end‑measure verification, fixture setup and repeatable inspection tasks in metrology and workshop environments. Workshop-grade construction for daily use Diameter 17.92 mm with ±0.002 mm tolerance 50 mm length for standard fixture compatibility Precision for repeatable end‑dimension checks The compact test pin is engineered to provide consistent reference geometry for end‑measure inspections and go/no‑go checks. With a nominal diameter of 17.92 mm and a stated accuracy of ±0.002 mm, the component offers the kind of dimensional certainty required for critical alignment and inspection tasks. The tight tolerance reduces scatter in measurement series, which improves process control and reduces rework; this is particularly valuable when setting up jigs or verifying bores where even small deviations affect assembly quality. The solid construction ensures the reference surface remains stable under normal shop handling, supporting repeatability across measurement cycles. Robust workshop design that fits production needs Built as a workshop version, the pin combines durability with straightforward handling. The body is made from special steel, delivering wear resistance where frequent insertion and withdrawal are required. At 50 mm overall length the pin matches common fixture depths and bench setups while its modest mass (around 0.15 kg) balances rigidity with ease of positioning. The form factor allows the pin to be used as a fixed reference or as a temporary plug gauge during setup routines. Where interchangeability with existing gauge sets is needed, the nominal diameter and standard length keep integration simple and predictable. Practical integration into inspection and setup workflows Use cases include bore verification, fixture alignment, end‑face checks and calibration aids on inspection benches. The pin supports direct comparison methods and can be paired with calipers or micrometres where a tactile reference is required. Because the item is offered as a single test pin, it is suited to workshops that need a specific nominal size for process checks or for building matched sets incrementally. Metav’s distribution ensures steady availability from Emmerich, and the product’s workshop focus reflects the brand’s aim to make precise metrology tools accessible for everyday industrial use while maintaining supply reliability across the European market. For practical advice or order placement for the Metav IndustryLine gauge pin M323.H92, contact Metav Werkzeuge in Emmerich by email at info@metav-werkzeuge.com or by phone at +49 2822 7131930 to discuss specification fit and delivery options Technical Data Article number: M323.H92 GTIN: 4061905449239 Brand: Metav IndustryLine Label: Prüfstift, einzeln, 17,92 mm Länge 50 mm Facts Nominal diameter: 17.92 mm Accuracy: ±0.002 mm Length: 50 mm Weight: 0.15 kg Special features Material: special steel Version: workshop execution Application: end‑measure verification, fixture setup, bore checks FAQ What tolerance does the gauge pin carry? The gauge pin M323.H92 from Metav IndustryLine is specified with an accuracy of ±0.002 mm, suitable for precise end‑dimension checks. Which material is used for this test pin? This test pin is manufactured from special steel, selected for wear resistance in workshop environments. For which tasks is the pin primarily intended? Typical uses include bore verification, fixture alignment and end‑face checks where a stable reference diameter (17.92 mm) and a 50 mm length are required. Is a calibration certificate supplied with the pin? The product data does not indicate a supplied calibration certificate; if a certificate is required, please request specific calibration options when enquiring about the M323.H92. Can the pin be integrated with existing gauge sets and fixtures? Yes, the nominal diameter and standard 50 mm length allow straightforward integration into common fixtures and inspection routines. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
17.93mm Gauge Pin Length 50mm Workshop Version, Special Steel - Metav IndustryLine
Take advantage of the combination of high dimensional accuracy and robust special‑steel construction for reliable, repeatable inspection results; order the test pin directly via Metav Werkzeuge or consult the Metav team for application advice. Test pin, single — Gauge pin Ø 17.93 mm, length 50 mm (Metav IndustryLine) A Test pin, single, 17.93 mm, length 50 mm designed for precise end‑gauge and fit checks in workshop inspection and fixture setup. Workshop version, precision ground Diameter 17.93 mm for end‑gage use Length 50 mm with ±0.002 mm tolerance Made from special steel for durability Repeatable accuracy for inspection and fit control The gauge pin is produced to a tight tolerance of ±0.002 mm, providing a reliable reference for end‑gauge checks, plug tests and locating pins in fixtures. This level of precision minimises measurement uncertainty and supports quality control routines where repeatability is essential. By reducing variation at the interface between pin and bore, the component acceptance decision becomes more consistent, shortening inspection time and lowering scrap rates. The use of a clearly defined tolerance range also simplifies documentation and traceability in inspection records. Durable construction suited to workshop environments Manufactured from special steel and supplied in a workshop version, the pin balances surface hardness and toughness to withstand repeated seating and withdrawal from mating bores. The 50 mm overall length gives sufficient engagement for stable seating while keeping handling straightforward; a mass of 0.15 kg indicates a compact, easy‑to‑manipulate part. The ground finish improves wear resistance and contact repeatability, helping to maintain dimensional integrity over many cycles and reducing the need for frequent replacement. Practical integration into quality workflows The solid, single‑piece design permits immediate use in go/no‑go gauges, fixture locating points and portable inspection kits. Marking and the supplied identifiers allow straightforward inventory control and process documentation; the item is listed under SKU M323.H93 and GTIN 4061905449796 for procurement and traceability. Where measurement uncertainty budgets are tight, using this pin as a stable mechanical reference helps to reduce reliance on more complex instruments for simple pass/fail checks, increasing throughput without compromising on control. Choose Metav IndustryLine inspection pins via Metav Werkzeuge for dependable workshop performance and straightforward procurement — contact info@metav-werkzeuge.com or call +49 2822 7131930 for ordering or technical clarification Technical data Article number: M323.H93 GTIN: 4061905449796 Facts Diameter: 17.93 mm Length: 50 mm Weight: 0.15 kg Tolerance: ±0.002 mm Special features Material: Special steel Workshop version Category: Gauge pin (Messstifte) FAQ What is the nominal diameter of this gauge pin? The nominal diameter is 17.93 mm as supplied in the Test pin, single, 17.93 mm, length 50 mm (SKU M323.H93). What tolerance can be expected during use? The inspection pin is manufactured to a tolerance of ±0.002 mm, ensuring repeatable fit checks and consistent go/no‑go evaluations. Which material is used for the pin? The pin is made from special steel, selected for a balance of wear resistance and toughness suitable for workshop inspection tasks. Can this pin be used for fixture locating and end‑gage tests? Yes, the solid single‑piece design is intended for end‑gage use, fixture locating and plug testing in production and inspection workflows. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
17.94mm Gauge Pin, Single, 50mm Length, Workshop Finish - Metav IndustryLine
Take advantage of precise end‑dimension control and robust workshop construction: the combination of a 17.94 mm working diameter, a 50 mm shaft length and a tight ±0.002 mm tolerance supports repeatable go/no‑go and reference checks in routine inspection tasks. Order the gauge pin directly via Metav Werkzeuge or contact the consultants for compatibility advice. Gauge pin M323.H94 — single test pin, 17.94 mm Ø, 50 mm length (Metav IndustryLine) A gauge pin M323.H94 for precise end‑dimension inspection and routine workshop verification, suitable for fixture checks and assembly control. Workshop execution for everyday use Precise diameter: 17.94 mm Solid 50 mm shaft for stable probing High repeatability with ±0.002 mm Improve inspection reliability with a compact reference element The gauge pin is designed as a compact, stable reference for dimensional checks, offering a 17.94 mm nominal diameter combined with a 50 mm shaft that keeps handling straightforward while preserving stiffness. The declared tolerance of ±0.002 mm ensures that measurements used for go/no‑go decisions or assembly verification remain consistent, reducing rework and stoppages. As a simple, single‑piece test element, it fits into pneumatic or manual fixtures as well as bench inspection routines, providing a low‑complexity means of increasing throughput without modifying existing measurement equipment. Material choice and durability that suits daily workshop demands Made from special steel, this test pin resists wear from repeated contact and maintains dimensional stability under normal workshop conditions. The workshop execution emphasises robustness, so the component stands up to regular use in production and quality control areas. The material and finish together contribute to long service life and minimise the need for frequent replacement, delivering a cost‑effective inspection solution over many production cycles. Where traceable calibration is required, Metav can advise on suitable procedures to integrate the pin into existing quality systems. Practical handling, integration and typical applications The single test pin is straightforward to handle and to integrate into jigs, plug gauges and gauge blocks. Typical applications include end‑dimension verification, fixture setup, repeatability checks and final inspection of shafts or bores where a precise reference diameter is needed. The modest weight of the element supports simple manual handling while its geometry allows secure seating in clamps or holders. For production environments seeking reliable, repeatable results with minimal setup time, this test pin provides a pragmatic balance of precision and ruggedness. Contact Metav Werkzeuge today to discuss the suitability of the Metav IndustryLine gauge pin M323.H94 for specific inspection tasks, request calibration options or obtain a tailored supply proposal; phone +49 2822 7131930 or email info@metav-werkzeuge.com Technical data Article number: M323.H94 GTIN: 4061905449802 Manufacturer: Metav IndustryLine Dimensions & precision Diameter: 17.94 mm Length: 50 mm Tolerance: ±0.002 mm Weight: 0.15 kg Special features Material: special steel Workshop execution Application: end‑dimension inspection and fixture checks Single test pin, individual delivery FAQ What inspection tasks is this gauge pin suitable for? The gauge pin M323.H94 from Metav IndustryLine is intended for end‑dimension verification, fixture setup and repeatability checks where a precise reference diameter of 17.94 mm is required. Is the tolerance of ±0.002 mm sufficient for production control? Yes, the ±0.002 mm tolerance offers tight repeatability for many workshop and production control applications and supports reliable go/no‑go decisions when used as a reference element. Which material was used and how does it affect wear resistance? The test pin is manufactured from special steel, chosen for its durability under repeated contact; this material helps minimise wear and maintain dimensional stability in routine inspection use. Can the pin be integrated into jigs and fixtures? Integration into jigs, plug gauges and fixture mounts is straightforward; the 50 mm shaft provides adequate engagement for stable seating in manual and mechanical holders. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
17.95mm Test Probe 50mm Length Workshop Version, Special Steel - Metav IndustryLine
Taking advantage of precise tolerances and a compact length, this gauge pin delivers repeatable end-measurements with minimal setup effort; its special steel construction and protective case ensure workshop-ready durability. Order via Metav Werkzeuge for reliable supply or consult our advisors for application guidance. Gauge Pin M323.H95 – Single 17.95 mm Ø, 50 mm Length (Metav IndustryLine) The gauge pin M323.H95 is a single, hardened pin for precision end-measurements and alignment tasks in micro-range workshop applications. Single gauge pin Ø 17.95 mm Length 50 mm for compact setups Special steel, workshop version Delivered in protective case Consistent accuracy for end-measurements A compact measuring element designed for repeatable results: the 17.95 mm diameter and 50 mm length provide a stable contact area for end-face and alignment checks. With an indicated positional tolerance of ±0.002 mm, the component supports fine adjustment tasks and verification operations where small deviations matter. The precise geometry reduces setup iterations and contributes to faster throughput in inspection sequences, making the tool an efficient choice for short-run quality controls and fixture set-up routines. Robust construction for everyday workshop use Manufactured in special steel and supplied in a protective case, this workshop-oriented pin resists the handling typical in production environments while remaining easy to store and transport. The solid material selection balances surface hardness with dimensional stability so that frequent insertion and removal do not compromise the reference diameter. The compact format suits confined jigs and measuring fixtures, providing a durable reference that preserves calibration intervals and lowers the risk of measurement-related rework. Practical handling and integration benefits The simple, single-pin design enables quick exchange in fixture plates or verification benches, reducing machine downtime during changeovers. As a dedicated end-measurement tool, it is particularly useful for verifying bore seats, setting gauges and transferring reference dimensions between components. The compact dimensions mean the pin is easy to position by hand or clamp, and the supplied protective case ensures safe storage between uses, preserving the critical surface quality required for repeatable measurement results. Contact Metav Werkzeuge today for availability, technical matching and delivery options for the M323.H95 gauge pin; our specialists in Emmerich are available to advise on workshop integration and stock supply Technical data SKU: M323.H95 GTIN: 4061905069826 Article type: Gauge pin Core measurements Diameter: 17.95 mm Length: 50 mm Tolerance: ±0.002 mm Weight: 0.15 kg Special features Material: Special steel Workshop version Protective case for transport and storage ECLASS: 21170231 FAQ What accuracy can be expected from this gauge pin? The gauge pin M323.H95 is specified with a tolerance of ±0.002 mm, providing the dimensional stability required for fine end-measurements and alignment checks. Is the pin suitable for fitting into small fixtures and jigs? Yes, the 17.95 mm diameter and 50 mm length make the M323.H95 well suited to compact fixtures and confined measuring setups in workshops. How is the M323.H95 supplied for transport and storage? The gauge pin is supplied in a protective case to safeguard the measuring surface during transport and storage. Which material is used for this measuring pin? This measuring pin is made from special steel, chosen to combine surface durability with dimensional reliability for workshop use. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
17.96mm Test Pin, Single, 50mm Length Workshop Version - Metav IndustryLine
Benefit from exact dimensional control and robust workshop design: the pin’s 17.96 mm nominal diameter combined with a ±0.002 mm tolerance ensures repeatable fit checks and profile verification, while the 50 mm length reaches into deeper bores. Order the gauge pin directly via Metav Werkzeuge or consult our specialists for application advice. Gauge pin M323.H96, single 17.96 mm diameter, 50 mm length (Metav IndustryLine) A gauge pin M323.H96 designed for precise fit checks, end‑measure verification and fixture set‑up in metrology and workshop quality control, supplied as an individual test pin for one‑piece checks. Diameter 17.96 mm with ±0.002 mm accuracy 50 mm overall length for internal checks Made from special steel Supplied individually, single‑piece delivery Reliable sizing for precise fit and inspection The central benefit of this test pin is its dimensional precision: a nominal diameter of 17.96 mm held to ±0.002 mm provides a measurable reference that reduces uncertainty in go/no‑go and alignment operations. For production environments where bore tolerances and thread fits must be verified quickly, this compact control element enables a straightforward, quantitative decision: either the fit conforms or adjustment is required. The specified tolerance corresponds to a two‑micrometre window, which is sufficient for many precision engineering tasks and small‑batch quality checks. Robust workshop design that endures routine handling Manufactured in a workshop configuration, the pin is made from special steel and finished to maintain consistent geometry during repeated use. The 50 mm length offers access into moderately deep bores and fixtures while remaining easy to handle with one hand or small tools. This construction balances durability with practicality: the compact form resists deformation under typical bench conditions and simplifies storage and identification in a busy measuring kit. The design therefore supports frequent inspection cycles without compromising repeatability. Integrates simply into measurement and setup workflows As an individual gauge pin, the component integrates into go/no‑go sets, alignment jigs and calibration routines as a defined reference. The single‑piece supply reduces packaging waste and simplifies ordering for specific sizes needed for jigs, mandrels or plug‑gauge pairing. Traceable identifiers such as the SKU and GTIN allow clear stock management and cataloguing in quality systems, facilitating inventory control and audit trails. For bespoke applications or questions about interchangeability with existing gauges, the Metav team can provide technical guidance and compatibility checks. For tailored procurement or technical consultation regarding the Metav IndustryLine gauge pin M323.H96 — including suitability for specific fixtures and inspection tasks — contact Metav Werkzeuge at info@metav-werkzeuge.com or call +49 2822 7131930 for direct assistance Technical data SKU: M323.H96 GTIN: 4061905070099 Brand: Metav IndustryLine Core measurements Diameter: 17.96 mm Length: 50 mm Accuracy: ±0.002 mm Weight: 0.15 kg Special features Material: special steel Workshop execution Single‑piece supply Category: gauge pin FAQ What are the exact dimensions of this gauge pin? The gauge pin M323.H96 has a nominal diameter of 17.96 mm and an overall length of 50 mm. What tolerance does the pin maintain? The pin is specified with an accuracy of ±0.002 mm, suitable for fine workshop fit checks and many inspection tasks. Which material is used for the pin? This Metav IndustryLine test pin is machined from special steel and finished for dimensional stability in routine use. Can this pin be used for checking bore fits and fixture alignment? Yes, the M323.H96 is intended for fit verification, alignment and end‑measure checks in workshop and metrology applications. How is the product identified for ordering and inventory? Order and catalogue the part using SKU M323.H96 or GTIN 4061905070099; both identifiers streamline procurement and stock management. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
17.97 mm Gauge Pin 50 mm Length Workshop Finish - Metav IndustryLine
Combining high dimensional accuracy (±0.002 mm) with a robust workshop design provides consistent fit checks and reduced rework; order the gauge pin directly via Metav Werkzeuge or consult our metrology specialists for application support. Gauge Pin M323.H97 — Single test pin, Ø 17.97 mm, length 50 mm (Metav IndustryLine) The Gauge Pin M323.H97 is a single test pin designed for precise fit and gauge checks in workshop metrology and quality-control routines. High accuracy ±0.002 mm tolerance Diameter Ø 17.97 mm for tight fits Length 50 mm for standard assembly checks Workshop version for everyday robustness Accurate fits for repeatable measurements The single test pin delivers high dimensional accuracy with a stated tolerance of ±0.002 mm, making it suitable for precision fit checks and final inspection tasks. This tight tolerance reduces uncertainty when assessing bores, dowel holes or mating parts, so measurement decisions can be made faster and with greater confidence. The controlled diameter and short, rigid geometry minimise bending and runout during manual handling, which helps to maintain repeatability across multiple checks. Robust construction for workshop workflows Manufactured from special steel and offered in a workshop version, the pin is designed for repeated use in a production environment. The 50 mm length gives sufficient engagement for common bushings and housings while remaining easy to handle on the shop floor. The material choice balances surface wear resistance with dimensional stability, so the component resists deformation under normal inspection loads and keeps its calibrated condition for longer intervals between verifications. Practical benefits for quality control and process reliability Using a purpose-made test pin simplifies go/no-go assessments and reduces the need for elaborate fixtures. The compact design is straightforward to integrate into existing inspection benches and enables quick visual and tactile checks alongside gauge blocks or plug gauges. Supplied as a single item with clear product identification (SKU M323.H97, GTIN 4061905070105), the pin supports traceable workflows and efficient stock management in maintenance or production settings. Contact Metav Werkzeuge for tailored advice on integrating the Metav IndustryLine gauge pin into existing quality processes or to request a quotation for specific batch quantities Technical Data Article number: M323.H97 GTIN: 4061905070105 Manufacturer: Metav IndustryLine Facts Length: 50 mm Diameter: 17.97 mm Tolerance: ±0.002 mm Weight: 0.15 kg Special features Workshop version Material: special steel Single test pin Accurate, short rigid geometry FAQ What inspection tasks is this test pin suitable for? The gauge pin M323.H97 from Metav IndustryLine is intended for precision fit checks, bore verification and assembly conformity tests where a diameter of 17.97 mm and a length of 50 mm are required. How precise is the diameter of the pin? The diameter is specified to a tolerance of ±0.002 mm, which makes the pin appropriate for high-precision workshop inspections and repeatable go/no-go assessments. Is the pin delivered individually or in sets? This item is supplied as a single test pin, referenced under SKU M323.H97, suitable for stocking as a spare or for targeted inspection tasks. What material is used and how does it affect wear? The pin is made from special steel, chosen to provide a balance of wear resistance and dimensional stability under normal inspection loads. Can the pin be used for calibration reference in a small workshop? Yes, the gauge pin M323.H97 is designed for workshop metrology and supports reliable practical checks; for formal calibration procedures, please consult Metav Werkzeuge for recommended verification intervals. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
17.98mm Gauge Pin 50mm Length Workshop Version - Metav IndustryLine
Reliable workshop-grade gauge pin combining 17.98 mm nominal diameter, a manufacturing tolerance of ±0.002 mm and a 50 mm working length for consistent end‑measurements; order directly via Metav Werkzeuge or contact our consultants for application advice. Gauge pin, single, 17.98 mm, 50 mm — Metav IndustryLine workshop version The gauge pin, single, 17.98 mm, 50 mm is a hardened reference plug for precise fit checks and end‑measurements in workshop inspection and production control. Workshop version, robust for daily use Diameter 17.98 mm with ±0.002 mm fit 50 mm hardened special-steel body Precise end-measurement for fit checks Precision where it matters for fit and clearance testing The gauge pin is manufactured to a tight ±0.002 mm dimensional tolerance, making it suitable for repeatable fit checks and final size verification in production and inspection routines. A nominal diameter of 17.98 mm gives a reliable reference for checking bores, gauges and mating parts; the indicated tolerance corresponds to typical gauge‑level manufacturing control and supports objective pass/fail judgements. Classified within the micro range (10–100 mm), this size offers the best balance of stiffness and accessibility for small to medium components, reducing flex and improving reproducibility compared with longer measuring plugs. Robust construction for frequent workshop handling Machined from special steel and finished for durability, the pin’s 50 mm overall length provides sufficient engagement without becoming unwieldy in handheld checks or fixture use. The workshop specification ensures surface and dimensional stability under regular use, while the mass and profile support secure seating in measuring fixtures or manual checking. By limiting operator variability through consistent geometry and material hardness, the pin helps reduce measurement scatter and downstream rework — a practical advantage in serial production and quality control stations. Fits into established inspection workflows and traceable routines Designed as a simple, reliable reference element, the pin integrates into go/no‑go checks, bore matching and end‑measurement protocols commonly found in manufacturing QA. Its repeatable geometry supports documented inspection steps and helps shorten decision cycles on assembly lines. For users requiring support, Metav provides technical advice and accessory suggestions to align the pin with existing gaging sets and test benches, ensuring the tool contributes to measurable improvements in throughput and fewer ambiguous measurements. For workshop-grade precision from the Metav IndustryLine range, order this gauge pin via Metav Werkzeuge or contact our specialists in Emmerich for tailored advice at info@metav-werkzeuge.com or +49 2822 7131930 Technical data Article number: M323.H98 GTIN: 4061905070990 Label: Prüfstift, einzeln, 17,98 mm Länge 50 mm Facts Nominal diameter: 17.98 mm Length: 50 mm Weight: 0.15 kg Manufacturing tolerance: ±0.002 mm eClass: 21170231 Special features Material: Special steel Version: Workshop specification Category: Gauge pins / Messstifte Storytrigger: end masses FAQ What is the intended use of this gauge pin? The gauge pin (Metav IndustryLine gauge pin, single, SKU M323.H98) is intended for fit checks, bore verification and end‑measurements in workshop and inspection environments. Does the pin offer laboratory calibration on delivery? The Metav IndustryLine gauge pin is supplied as a precision workshop item; any laboratory calibration or certification options can be arranged through Metav Werkzeuge on request. Which materials is the pin suitable for contacting during inspection? The pin is manufactured from special steel and is suitable as a non‑cutting reference contact for common engineering materials during inspection and assembly checks. How does the ±0.002 mm tolerance affect inspection decisions? A tolerance of ±0.002 mm defines the manufacturing variation of the pin; this small tolerance supports consistent go/no‑go decisions where tight fits and small clearances are required. Can the pin be used in fixture or jig applications? Yes — the 50 mm length and workshop specification make the pin suitable for use in fixtures and manual jigs for repeated dimensional checks. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
17.99mm Gauge Pin 50mm Length Workshop Version, Special Steel - Metav IndustryLine
Precision inspection becomes straightforward with a workshop‑grade gauge pin that pairs a nominal 17.99 mm diameter with a tight ±0.002 mm manufacturing tolerance and resilient special steel construction; order the gauge pin directly via Metav Werkzeuge or ask the consultants if assistance is required. Gauge pin, single, 17.99 mm × 50 mm — Metav IndustryLine workshop version The gauge pin, single, 17.99 mm × 50 mm is a compact inspection probe designed for end‑measure checks and plug‑gauge applications in workshop environments. Precision diameter 17.99 mm, ±0.002 mm tolerance 50 mm length for compact gauge setups Made from special steel for durable use Accurate inspection for repeatable results A tight dimensional tolerance of ±0.002 mm combined with the 17.99 mm nominal diameter delivers measurable repeatability for go/no‑go and end‑measure checks. The reduced allowance helps to limit ambiguous pass/fail decisions and shortens inspection loops, supporting a lean quality workflow. In practice, this level of precision reduces downstream rework and streamlines in‑machine verification by providing a clear reference point for fixture set‑up or comparative gauging; the single‑piece format suits targeted checks where one reference probe is required. Durable construction built for workshop use Manufactured from special steel, this workshop variant is engineered for routine handling in industrial settings. The material choice favours wear resistance under repeated insertion and withdrawal cycles, preserving the gauge geometry over time and sustaining the stated tolerance. The rugged construction suits bench work and production‑line checks where components are sampled frequently and durability is essential to maintain calibration intervals and ensure consistent measurement results. Compact design that fits measurement routines With a 50 mm length and a mass of 0.15 kg, the probe balances accessibility and stability: the short form factor permits use in confined fixtures while still providing sufficient contact length for secure handling. Supplied as a single gauge pin, it integrates easily into existing plug‑gage sets, fixture checks or portable inspection benches without excess overhang that can introduce measurement variability. The straightforward geometry simplifies interpretation of contact points, helping technicians focus on decisive measurement outcomes rather than setup complexity. For reliable workshop measurements choose the Metav IndustryLine gauge pin M323.H99 — contact Metav Werkzeuge to discuss supply and compatibility with existing inspection equipment Technical data Article number: M323.H99 GTIN: 4061905071003 Brand: Metav IndustryLine Facts Diameter: 17.99 mm Length: 50 mm Tolerance: ±0.002 mm Weight: 0.15 kg Special features Material: Special steel Workshop version Single gauge pin FAQ What are the precise dimensions and tolerance of this gauge pin? The gauge pin has a nominal diameter of 17.99 mm and a length of 50 mm with a manufacturing tolerance of ±0.002 mm; the Metav IndustryLine gauge pin (M323.H99) is supplied as a single inspection probe. Is the material specified suitable for frequent use in a workshop? Yes, the pin is made from special steel, chosen to withstand routine insertion cycles and provide resistance to wear so that the dimensional stability is preserved during typical workshop handling. Which inspection tasks is this type of gauge pin suited to? This style of gauge pin is intended for end‑measure checks, plug‑gauge verifications and fixture set‑up where a single reference probe of 17.99 mm is required for pass/fail evaluation or comparative measurement. How should the gauge pin be handled to maintain accuracy? Handle the probe by the shank, avoid impacts or dropping, keep contact faces free from debris and store in a dry, cushioned location to minimise nicks and preserve the stated tolerance. Metav IndustryLine: Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
17.9mm Gauge Pin 50mm Length Workshop Version - Metav IndustryLine
Take advantage of the combination of industrial precision, robust special steel construction and compact handling for reliable dimensional checks in the workshop; place orders or request advice directly via Metav Werkzeuge to keep inspection routines efficient and reproducible. Gauge pin, single, 17.90 mm, length 50 mm — Metav IndustryLine Gauge pin, single, 17.90 mm, length 50 mm serves as a dedicated inspection pin for quick bore checks and end-dimension verification in production and toolrooms. Gauge pin Ø 17.90 mm, length 50 mm Workshop design, robust special steel Tolerance ±0.002 mm for precise checks Supplied individually for controlled use Consistent, certified-level checking for everyday quality control A compact inspection pin designed for routine dimensional verification, the gauge pin with Ø 17.90 mm and length 50 mm provides a simple yet reliable way to confirm end dimensions and bore fits. With an applied tolerance of ±0.002 mm, this tool supports close limit checking where repeatability matters; the stated tolerance reflects the pin's manufacturing precision and makes it suitable for tasks that require more accuracy than common workshop gauges. The slim, single-piece design reduces handling variables and simplifies comparison checks against reference gauges or fixture seats. Robust construction that stands up to workshop use Manufactured from special steel, the pin combines wear resistance with stable geometry for repeated measurements. The workshop design emphasises durability: smooth surfaces reduce the risk of damage to both the pin and the workpiece, while a compact mass (approx. 0.15 kg) ensures easy handling during frequent checks. This balance of toughness and manageability supports efficient inspection loops on the shop floor, reducing downtime associated with re‑sets or repeat measurements. Practical integration into inspection workflows As a single, dedicated inspection pin supplied individually, this item is ready for insertion into test fixtures, comparison holes or bench checks without additional assembly. Its nominal diameter and fixed length simplify traceability in inspection records and help standardise go/no-go assessments in serial production. For environments where a sequence of quick checks keeps throughput high, the straightforward geometry of this pin reduces operator training time and streamlines measurement routines. Why this choice benefits procurement and workshop teams Choosing a purpose-made inspection pin in special steel with ±0.002 mm tolerance reduces uncertainty during acceptance checks and saves time that would otherwise be spent on secondary verification. The item’s focused functionality supports lean inspection concepts: minimal set-up, immediate readout via comparison, and predictable behaviour under repeated use. Together with Metav IndustryLine’s product selection, this pin suits machine shops, maintenance departments and quality control benches that prioritise reliable, repeatable checks over decorative or multifunction tools. Contact Metav Werkzeuge for procurement details and to align the Metav IndustryLine gauge pin with specific measurement standards in your facility Technical data Article number: M323.H90 GTIN: 4061905449215 Manufacturer: Metav IndustryLine Category: Gauge pins Facts Diameter: 17.9 mm Length: 50 mm Tolerance: ±0.002 mm Weight: 0.15 kg Special features Material: Special steel Workshop version Supplied individually Label: Prüfstift, single inspection pin FAQ What is this gauge pin used for? The gauge pin is intended for quick bore checks and end-dimension verification in production, toolrooms and quality control benches. What dimensional accuracy does the pin offer? The pin provides a manufacturing tolerance of ±0.002 mm, making it suitable for close-limit inspection tasks requiring fine repeatability. What material is the inspection pin made from? The inspection pin is made from special steel, selected for wear resistance and stable geometry under repeated use. How is the item supplied? The gauge pin is supplied individually, prepared for immediate use in fixtures or bench checks. Which work environments are best suited to this pin? Machine shops, maintenance departments and small-batch production lines benefit from the pin’s compact form and precision for routine dimensional checks. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
170mm Setting Ring, Hardened Gauge Steel, Form C, DIN 2250 / DIN 286 JS3 - Metav IndustryLine
Take advantage of a hardened, lapped gauge steel ring that conforms to DIN 2250 and DIN 286 with JS 3 tolerance for repeatable setting and inspection tasks; its 170 mm nominal diameter and robust construction support stable use in the workshop. Order the setting ring directly via Metav Werkzeuge or ask our consultants if needed. Setting ring 170 mm, gauge ring (DIN 2250) — Metav IndustryLine A Setting ring 170 mm designed for precise reference and master-governed inspection work in machining and quality control environments. Hardened, lapped gauge steel body Conforms to DIN 2250 and DIN 286, JS 3 tolerance Robust Form C geometry for stable seating Suitable for workshop and inspection use Repeatable inspection with standardised tolerances The ring gauge is manufactured from gauge steel, accurately hardened and lapped to provide a reference surface that resists wear and distortion. Conformity to DIN 2250 and DIN 286 with JS 3 tolerance ensures the component serves reliably as a master for setting and verification tasks. For inspection rooms and shop floors that require documented interchangeability, this precision ring offers a predictable dimensional baseline, reducing the risk of measurement drift when used as a master for bore gauges or as a setting standard for adjustable instruments. Durable design for everyday workshop handling Finished in a manner that prioritises long-term stability, the gauge’s Form C geometry and substantial mass (approx. 6 kg) give it the rigidity needed for frequent handling. The lapped internal surface delivers a smooth seat for probes and gauges, while the hardened body resists knocks and abrasion that can occur in production environments. Built for practical use rather than delicate laboratory-only tasks, the ring combines serviceability with low maintenance: occasional cleaning and proper storage preserve the reference condition and extend service life. Practical applications and compatibility with standard workflows Measured at 170 mm, this ring sits within the Standard measurement range, making it appropriate for general machine‑shop work, fixture setup and calibration benches. As a setting master, it pairs with bore gauges, plug gauges and precision measuring heads to establish machine zero points and to check gauge blocks or fixtures. Traceability is supported by the clear norm references and SKU marking, so the ring integrates smoothly into quality control documentation and process audits. Its specification suits both production-oriented inspection and toolroom verification tasks where repeatable results are essential. For a reliable reference master with industrial durability choose the Metav IndustryLine setting ring and contact Metav Werkzeuge in Emmerich for tailored advice and prompt supply via info@metav-werkzeuge.com or +49 2822 7131930 Technical Data Article number: M313.170 GTIN: 4054469121208 Diameter: 170 mm Weight: 6 kg Facts Material: gauge steel, hardened and lapped Standards: DIN 2250 and DIN 286, JS 3 Form: Form C ECLASS: 21170104 Customs tariff number: 90173000 Special features Robust construction for workshop use Lapped internal surface for smooth seating Designed as a setting/master ring for inspection FAQ What is the intended use for this setting ring? The setting ring is intended as a reference master for setting, calibration and verification of bore gauges and fixtures; the Setting ring 170 mm from Metav IndustryLine (SKU M313.170) is optimised for workshop and inspection tasks. Is the material resistant to workshop wear? Yes — the ring is made from hardened, lapped gauge steel, which improves wear resistance and preserves the reference surface during regular handling. Which standards does the ring comply with? The product meets DIN 2250 and DIN 286 requirements and is manufactured to JS 3 tolerance, providing documented conformity for quality systems. Can this ring be used for routine calibration documentation? The ring’s normative references and clear SKU marking (M313.170) make it suitable as a documented reference in calibration procedures and inspection records. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
175 mm Setting Ring Form C Hardened Gauge Steel DIN 2250/DIN 286 JS3 - Metav IndustryLine
The combination of hardened, lapped gauge steel and DIN 2250 / DIN 286 JS3 tolerance ensures a stable master reference for setting and calibration tasks; the defined Form C profile supports reproducible seating and quick, repeatable checks. Order the ring directly via Metav Werkzeuge or consult the team for application-specific advice. Setting ring 175 mm — DIN 2250 master ring, hardened gauge steel (Metav IndustryLine) Setting ring 175 mm is a precision master ring for calibration, gauge setting and reference measuring in inspection and workshop environments. Hardened, lapped gauge steel DIN 2250 / DIN 286 tolerance JS3 175 mm nominal diameter Form C profile for secure seating Reliable master reference for workshop calibration A hardened and lapped master ring offers a trustworthy datum for setting internal gauges and comparators. The 175 mm nominal diameter provides a practical reference size for medium bores and toolroom applications while the processed surface minimises contact variability. Using a master ring made from hardened gauge steel reduces wear and preserves gauge integrity over repeated handling, which translates into fewer recalibrations and more consistent measurement routines on the shop floor. Traceable tolerances and repeatable results Built to DIN 2250 and verified to DIN 286, JS3, this ring provides clearly defined limits for a master reference, supporting traceable inspection chains and quality documentation. A tight tolerance class such as JS3 means less ambiguity when transferring a standard to portable instruments; in practice this improves the repeatability of successive settings and reduces rework caused by gauge drift. The robust construction aids in maintaining concentricity and form under normal workshop conditions, giving a repeatable seating surface for bore gauges and internal comparators. Practical benefits in everyday metrology work The Form C geometry ensures a positive mechanical contact during seating, simplifying the alignment of measuring probes and feeler contacts. The ring’s finish, achieved by lapping, yields a consistent contact plane that helps to avoid measurement artefacts induced by surface roughness. As a durable master reference, it supports routine tasks such as setting dial bore gauges, checking go/no-go mandrels and verifying comparator standards, thereby contributing to a smoother process flow and predictable inspection outcomes. Contact Metav Werkzeuge for specification matching and to arrange supply of this Metav IndustryLine setting ring; specialists can advise on gauge selection, calibration options and delivery. Technical data Article number: M313.175 GTIN: 4054469121215 Tariff number: 90173000 Diameter: 175 mm Weight: 6.8 kg Material: gauge steel, hardened and lapped Norm: DIN 2250; DIN 286, JS 3 Form: C Category: gauges (Lehren) FAQ What is the intended use of this setting ring? The setting ring is intended as a master reference for calibration and setting of internal gauges, comparators and bore-measuring devices; the Setting ring 175 mm (Metav IndustryLine, SKU M313.175) is suitable for medium bore references. Which standards and tolerances apply to the ring? The ring is manufactured to DIN 2250 and DIN 286 with tolerance class JS3, delivering a well-defined limit and suitable precision for shop‑level master references. How does the lapped finish affect measurement quality? The lapped surface reduces local surface irregularities and ensures more consistent contact between gauge and ring, improving repeatability when using the ring as a master reference. Is the material suitable for long-term workshop use? Constructed from hardened gauge steel and finished by lapping, the ring is designed for durability under regular handling and retains form stability over prolonged use. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
175mm Ceramic End Gauge DIN 861, Zirconia Ceramic, Hardness HV1250, Stainless Antimagnetic - Metav IndustryLine
High wear resistance and certified metrological accuracy combine to reduce recalibration cycles and ensure reproducible results; take advantage of the HV 1250 hardness and the DIN EN ISO 3650 conformity to secure reliable master measurements. Order the gauge directly via Metav Werkzeuge or consult our technical advisers for application guidance. Ceramic end gauge 175 mm DIN 861 — Zirconia ceramic, antimagnetic Ceramic end gauge 175 mm DIN 861 provides a compact, stable reference for length verification and transfer tasks in quality control and workshop settings Zirconia ceramic, highly wear-resistant Accuracy to DIN EN ISO 3650 Hardness HV 1250, twice steel Antimagnetic and corrosion-resistant Dependable metrology through standardised accuracy The DIN EN ISO 3650 conformity indicates that this end gauge meets recognised requirements for length references, making it suitable as a workshop master or for bench calibration tasks. With a nominal size of 175 mm, the component serves as a stable reference for verification of measuring instruments and fixtures; the standardised specification supports traceability chains and eases documentation in quality processes. This focus on measurable conformity delivers predictable results and reduces downtime caused by uncertain references. Material advantages that extend service life Manufactured from zirconia ceramic, the gauge offers exceptional abrasion resistance and dimensional stability under normal workshop environmental conditions. The HV 1250 rating—approximately twice the hardness of common steels—translates directly into slower wear of the measuring faces and longer intervals between maintenance or replacement. Being antimagnetic and corrosion-resistant, the material reduces interference from magnetic fields and avoids the oxidation issues that can affect metal gauges, which helps maintain measurement integrity in mixed-material environments. Compact geometry for stable contact and easy handling The rectangular cross-section of 35 x 9 mm balances rigidity and handling comfort: narrow faces reduce contact area where required, while sufficient depth maintains stability during measurements. The 175 mm length is practical for workshop benches and inspection rigs, offering a compromise between reach and control. Intended as a master end gauge, it is suited for comparative checks, set-up tasks and transfer measurements where a hard, wear-resistant reference surface ensures reproducible measurement points and minimal surface disruption. For specialist advice on integrating this Metav IndustryLine ceramic end gauge into existing inspection routines, or to place a direct order through Metav Werkzeuge, contact our technical advisers at Metav Werkzeuge for tailored support and delivery coordination Technical data Article number: M324.175 SKU: M324.175 Nominal size: 175 mm Standard: DIN 861 Numbers / Core technical data Cross-section: 35 x 9 mm Hardness: HV 1250 Nominal length: 175 mm Special features / Materials Material: zirconia ceramic Wear-resistant Antimagnetic Corrosion-resistant Accuracy standard: DIN EN ISO 3650 FAQ What applications suit this ceramic end gauge? The ceramic end gauge 175 mm DIN 861 (Metav IndustryLine, SKU M324.175) is suitable for master checks, comparative measurements and setting tasks in workshops and inspection benches where a hard, wear-resistant reference is required. How does the zirconia ceramic compare to steel gauges? Zirconia ceramic offers significantly higher hardness (HV 1250), enhanced wear resistance and antimagnetic behaviour compared with conventional steel gauges, which improves long-term stability of reference surfaces. Is the gauge compatible with standard calibration procedures? Yes, the gauge’s conformity to DIN EN ISO 3650 makes it appropriate as a reference item within documented calibration and inspection workflows and supports traceability requirements. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
17mm Limit Plug Gauge Go Side Wear Allowance, Hardened Steel, DIN 7162 - Filetta
Combining hardened steel construction, conformity to DIN 7162 and a deliberate wear allowance on the good side delivers dependable limit checking and extended service life in routine inspection tasks; order Filetta limit gauge pins via Metav Werkzeuge or consult our specialists for selection and supply advice. Limit gauge pin by Filetta — hardened steel, DIN 7162 Limit gauge pin designed for Go/No‑Go checks in production and QA environments Limit gauge pin ø 17 mm, hardened steel Conforms to DIN 7162 tolerances Wear allowance on the good side Suitable for plug and pin gauge control Dependable limit checking that stabilises production quality The solid, dimensionally stable construction supports fast, repeatable inspections on the shop floor and in quality control. Built from hardened steel, this pin maintains its nominal size under cyclic use, which reduces the risk of false rejects and rework. Conformity to DIN 7162 provides an objective reference for acceptance testing and helps to harmonise checks across suppliers and production lines, improving throughput and lowering non‑conforming parts per million. Reduced downtime thanks to a wear‑compensated design The integrated wear allowance on the good side extends the usable life of each pin by allowing controlled material loss while preserving the accept signal for Go checks. For maintenance planners and inspectors this means fewer replacements and more predictable tool cycles. The design philosophy emphasises long‑term precision, so inspection intervals can be scheduled on condition rather than by conservative fixed replacement, saving operational time without compromising measurement integrity. Practical suitability for workshop and gauge sets Manufactured for routine limit inspection duties, the pin is compact and straightforward to integrate into existing gauge sets and fixtures. The simple geometry supports quick insertion for plug checks and is compatible with standard bench routines. For technical procurement and production engineering teams, the combination of material choice and standard compliance provides a reliable basis for procurement decisions and spares planning, while Metav Werkzeuge can advise on kit assembly and batch supply options. For specification support or stock availability of Filetta limit gauge pins (MS911.179) contact Metav Werkzeuge for a tailored recommendation at info@metav-werkzeuge.com or call +49 2822 7131930 Technical Data Article number: MS911.179 Manufacturer: Filetta Size / Diameter: 17 mm Material: hardened steel Standard: DIN 7162 Special feature: wear allowance on the good side Specifications Diameter: 17 mm Design & Features Category: limit gauge pin / plug gauge Intended use: Go/No‑Go limit checking and quality control Application area: production inspection, incoming goods control FAQ What is this pin used for in production? This limit gauge pin (Filetta, MS911.179) is used for Go/No‑Go checks and routine limit inspections to verify bore and fit dimensions on parts. Does the pin meet a recognised standard? Yes, the Filetta pin complies with DIN 7162, ensuring standardized tolerance classes for limit gauges. How does the wear allowance affect service life? The built‑in wear allowance on the good side prolongs usable life by permitting controlled wear while maintaining the Go limit, reducing replacement frequency. Can Metav Werkzeuge supply matching gauge sets or replacements? Metav Werkzeuge can advise on compatible gauge sets and supply quantities; the Filetta MS911.179 can be ordered as part of a coordinated inspection kit. Manufacturer / Responsible: Schut Geometrische Meettechniek bv; Duinkerkenstraat 21; 9723 BN Groningen; The Netherlands; +31 50 5877877; schutnl@schut.com
17mm Test Probe 50mm Length Workshop Version - Metav IndustryLine
Take advantage of precision to ±0.002 mm, robust special‑steel construction and a compact 50 mm length for stable end‑dimension checks; order the gauge pin directly via Metav Werkzeuge or consult our specialists for tailored application advice. Gauge pin M323.H00 — workshop‑grade test pin, 17.00 mm diameter, 50 mm length The gauge pin M323.H00 is a single test pin designed for reliable end‑dimension checks and assembly verification in workshop and inspection environments. Diameter 17.00 mm, tolerance ±0.002 mm 50 mm length, workshop execution Made from high‑grade special steel Precision where end dimensions matter Engineered for tight end‑dimension control, this gauge pin offers a declared accuracy of ±0.002 mm, making it suitable for fine rejection limits and reference measurements in production checks. The defined 17.00 mm diameter delivers a reproducible datum for plug gauges, fixture set‑ups and mating part verification, reducing the risk of false rejects and rework. With such accuracy, measurement chains gain stability and traceability, which supports process control and quality documentation in machining and assembly operations. Robust construction for everyday workshop use Built in a workshop execution, the measuring pin combines a compact 50 mm working length with special‑steel durability to withstand frequent handling and insertion cycles. The compact form factor keeps bending and play to a minimum while remaining easy to fit into pin racks or inspection fixtures. The choice of special steel balances wear resistance and manufacturability, ensuring consistent diameters over many cycles and a long service life in standard production environments. Practical integration into gaging workflows As a single‑piece measuring element, the M323.H00 functions as a reference pin for end‑dimension inspection, assembly alignment and template checks. The compact design and clearly defined diameter simplify storage in pin sets and allow straightforward replacement of worn pins without recalibrating entire fixtures. Traceable identification via SKU and GTIN supports purchase reproducibility and inventory control within established procurement workflows, facilitating fast reordering and consistent quality across batches. For precise end‑dimension control, request the M323.H00 gauge pin from Metav Werkzeuge or consult our specialists for application‑specific recommendations and supply options. Technical data Article number: M323.H00 GTIN: 4061905071379 Label: Test pin, single, 17.00 mm diameter, 50 mm length Facts Diameter: 17.00 mm Length: 50 mm Accuracy: ±0.002 mm Weight: 0.15 kg Special features Workshop execution Material: special steel Single test pin (individual item) FAQ What tolerance is guaranteed for this gauge pin? The gauge pin M323.H00 is specified with an accuracy of ±0.002 mm, suitable for tight end‑dimension checks and reference measurement tasks. Which materials and applications suit this test pin? Made from special steel, the pin is intended for general workshop and inspection use such as plug gauge checks, assembly alignment and fixture references. Is the pin supplied as an individual item or in a set? This is supplied as a single test pin (individual item) under SKU M323.H00 for flexible use in existing pin sets or fixtures. How does the compact length affect measurement stability? The 50 mm working length provides a balance between accessibility and rigidity, reducing deflection during insertion and improving repeatability in typical workshop scenarios. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
17–18mm Gauge Pin Set 101 Pc 0.01mm Graduation With Probe Holder In Case - Metav IndustryLine
Take advantage of the combination of 0.01 mm step accuracy and a robust special steel construction for reproducible diameter checks and fewer reworks on the shop floor; order the pin gauge set directly via Metav Werkzeuge or ask our consultants if needed. Pin gauge set M318.587 — 17–18 mm, 0.01 mm increments (Metav IndustryLine) The Pin gauge set delivers precise diameter verification for workshop and inspection tasks, suited to use in toolrooms and quality-control benches. Accurate 0.01 mm increments Measurement range 17.00–18.00 mm Made from special steel Includes pin holder for secure handling Reliable sizing that reduces inspection uncertainty The set offers 0.01 mm diameter steps combined with a verified accuracy of ±0.004 mm, enabling reliable go/no-go checks and incremental sizing. Such resolution supports tight-tolerance work and simplifies decision-making during incoming inspection or final checks. Using fine increments minimises interpolation and makes it easier to select the correct rework strategy when clear evidence of deviation is required. The result is faster throughput and fewer ambiguous measurements on precision parts. Built for repeatable handling and safe storage Manufactured from special steel, the pins resist wear under frequent use while maintaining dimensional stability. The ensemble includes a secure pin holder, which keeps individual gauges organised and reduces handling damage during measurement sequences. The complete set is supplied in a compact transport case, facilitating safe movement between bench and machine or secure storage between shifts. These design choices protect the measuring surfaces and prolong service life, lowering total cost of ownership in busy workshops. Practical for toolrooms, gauge shops and quality control This comprehensive gauge solution is ideal where precise diameter verification is required for jigs, fixtures or mating components. In a toolroom or inspection lab the pins act as reference standards for bore checks and for confirming roundness or fit tolerances. The clear step size and robust material support both rapid shop-floor checks and more formal inspection processes, helping to reduce scrap rates and support consistent assembly quality across production batches. Handling, maintenance and longevity Simple maintenance keeps the set performing: wipe measuring faces with a lint-free cloth and a light corrosion inhibitor after use, and store pins in the supplied case to prevent nicks. Occasional visual inspection of contact faces will reveal any damage that could affect results; damaged pins should be segregated to avoid misleading measurements. Proper handling routines and the included pin holder ensure repeatability and traceable results over many inspection cycles. For supply and technical selection of the Metav IndustryLine pin gauge set, contact Metav Werkzeuge in Emmerich by e‑mail at info@metav-werkzeuge.com or by phone at +49 2822 7131930 for tailored advice and prompt delivery. Technical data Article number: M318.587 GTIN: 4054469156248 Customs tariff no.: 90173000 Manufacturer: Metav IndustryLine Core data Measurement range: 17.0–18.0 mm Increment: 0.01 mm Accuracy: ±0.004 mm Pieces per set: 101 Weight: 13 kg Length: 50 mm Special features Material: Special steel With pin holder Delivered in transport case Category: Pin gauges / gauge pins Label: Prüfstift-Satz, 17–18 mm, 0.01 mm steps FAQ What tolerance can be expected from this pin gauge set? The Metav IndustryLine pin gauge set (M318.587) is specified with an accuracy of ±0.004 mm, which supports precise diameter verification for standard workshop and inspection tasks. Is the set suitable for routine shop-floor checks or only for laboratory use? Designed for practical workshop use, the pin gauge set combines durable special steel construction and a transport case, making it well suited for both shop‑floor checks and more formal quality-control routines. How should the pins be maintained to preserve accuracy? After use, wipe the measuring faces with a lint-free cloth and a light corrosion inhibitor, store pins in the supplied transport case and keep the pin holder in use to avoid contact damage. Does the delivery include accessories for handling? Yes, the delivery includes a dedicated pin holder and a protective transport case to support organised handling and safe storage of the pins. Can these pins be used to check bore fits and gauge mating parts? The gauge pins in this set are intended for diameter verification, go/no-go checks and fit assessment of mating parts, providing clear, incremental evidence for acceptance or rework. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
18 mm Gauge Pin, 50 mm Length, Workshop Version, Special Steel, ±0.002 mm Accuracy, Supplied in Case - Metav IndustryLine
Take advantage of precise diameter control, robust workshop design and compact handling for reliable in-process checks; order the gauge pin directly via Metav Werkzeuge or consult the team for application guidance. Gauge pin M323.I00 — Gauge pin, 18.00 mm diameter, 50 mm length (Metav IndustryLine) A gauge pin intended for dimensional verification and fixture set-up in workshop environments, configured as a single item with a nominal diameter of 18.00 mm and a length of 50 mm. Workshop-grade design for daily use Diameter tolerance ±0.002 mm Compact 50 mm length for tight assemblies Made from special steel for wear resistance Precision where it counts for measurement and set-up The solid gauge pin delivers a tight tolerance of ±0.002 mm, providing a clear metrological basis for go/no‑go checks, bore verification and alignment tasks. The precise nominal diameter of 18.00 mm makes this pin suitable as a reference datum in fixtures and jigs where repeatability matters; the numerical tolerance supplies a verifiable figure for quality documentation. Compact dimensions reduce probe interference and simplify insertion into restricted bores, translating technical accuracy into dependable shop-floor results. Built for workshop efficiency and repeatable checks Designed as a workshop-grade item, this test pin combines a short 50 mm length with a robust cross section to limit bending and handling error during routine inspections. The construction from special steel ensures resistance to mechanical wear under frequent use, keeping the contact geometry stable over many cycles. For teams that require a reliable reference part for assembly validation or incoming inspection, the physical properties reduce rework and help maintain production flow without adding complexity to measurement routines. Straightforward handling for routine quality assurance Handling and visual inspection are uncomplicated: the single-item configuration and compact size allow fast positioning in gauges, fixtures or manual checks. The low mass contributes to easy manipulation while maintaining sufficient rigidity for accurate contact measurement. For documentation and traceability, the product identity is clear and stable, supporting quality records and process control. The combination of measurable tolerance, durable material and manageable form factor supports predictable measurement results in everyday workshop contexts. For application advice or to acquire the Metav IndustryLine gauge pin M323.I00, contact Metav Werkzeuge for precise recommendations by email or phone Technical Data Article number: M323.I00 SKU: M323.I00 GTIN: 4061905071010 eClass: 21170231 Label: Gauge pin, single, 18.00 mm length 50 mm Facts Diameter: 18.00 mm Length: 50 mm Tolerance: ±0.002 mm Weight: 0.15 kg Special features Material: Special steel Version: Workshop execution Item: Single unit Accuracy specification: ±0.002 mm FAQ What is the nominal diameter and tolerance of the gauge pin? The gauge pin has a nominal diameter of 18.00 mm with a tolerance of ±0.002 mm, specified for the Metav IndustryLine M323.I00. Which tasks is this pin suitable for? It is suitable for bore verification, fixture alignment and use as a reference datum during assembly and inspection processes. What material is the pin made from and is heat treatment specified? The pin is manufactured from special steel; no specific heat treatment or surface coating is stated in the product data. Can this pin be used in confined or tight-assembly checks? Yes, the compact 50 mm length and solid design make it well suited for checks in restricted bores and tight assemblies. How is repeatability ensured with this test pin? Repeatability is supported by the tight tolerance (±0.002 mm) and the robust workshop construction that minimises deformation during handling. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
18 mm Limit Gauge Plug, Wear Allowance On Good Side, Hardened Steel, DIN 7162 - Filetta
Take advantage of the combination of hardened steel construction, conformity to DIN 7162 and an integrated wear allowance on the go side for consistent, repeatable inspection results. Order the limit plug gauge directly via Metav Werkzeuge or consult our experts for application advice. Limit plug gauge — hardened steel, DIN 7162, 18 mm (Filetta) Limit plug gauge for precise bore acceptance testing and production line inspection, designed to meet workshop and laboratory needs with a compact nominal size. Hardened steel construction DIN 7162 conformity 18 mm nominal diameter Go side with wear allowance Dependable inspection where tolerances count The limit plug gauge is manufactured from hardened steel to provide a stable reference for go/no-go assessments and routine acceptance checks. Conformity to DIN 7162 ensures that the gauge's dimensions and form meet recognised metrological standards, which supports traceable inspection routines and simplifies documentation. The incorporated wear allowance on the go side extends usable life without compromising the acceptance criterion, so production control remains consistent over many inspection cycles. Practical performance for workshop and production use With a nominal size of 18 mm, this inspection gauge is suited to common bore diameters encountered in component production and maintenance. The compact geometry enables quick insertion checks that are compatible with standard go/no-go workflows, reducing process time while preserving measurement confidence. The plain design permits rapid visual discrimination between acceptable and non‑conforming parts, supporting efficient quality control in both single‑part checks and serial testing. Long service life and straightforward care The hardened steel construction combines durability with minimal maintenance requirements; routine handling and a simple cleaning routine maintain accuracy. The deliberate specification of a wear allowance on the go side means that small, predictable surface wear does not immediately invalidate the gauge, allowing scheduled requalification rather than frequent replacement. For traceable revalidation, the gauge can be included in a regular inspection plan that documents continued compliance with production tolerances. Contact Metav Werkzeuge for a specification sheet, availability or application guidance on this Filetta limit plug gauge (MS911.180) supplied to DIN 7162 standards Technical data Article number: MS911.180 Manufacturer: Filetta Material: hardened steel Nominal diameter: 18 mm Standard: DIN 7162 Facts Nominal diameter: 18 mm Special features Wear allowance on go side Suitable for go/no-go acceptance testing Category: gauges / inspection pins Image available (product thumbnail) FAQ What material is the gauge made from? The Filetta limit plug gauge MS911.180 is manufactured from hardened steel, chosen for wear resistance and dimensional stability. Which standard does the gauge comply with? The gauge is produced to DIN 7162, ensuring compatibility with established metrological expectations for limit gauges. What does the wear allowance on the go side mean? The wear allowance provides a controlled allowance for surface wear on the go face, extending service life while keeping the acceptance limit defined. For what inspection tasks is this gauge suitable? The gauge is intended for go/no-go acceptance testing of bores around 18 mm and for routine quality control in production and maintenance environments. How is the size identified on the product? The nominal diameter is indicated as 18 mm, matching the intended bore acceptance size for straightforward selection and use. Manufacturer / Responsible: Schut Geometrische Meettechniek bv; Duinkerkenstraat 21; 9723 BN Groningen; The Netherlands; +31 50 5877877; schutnl@schut.com
18 mm Limit Plug Gauge H7, Hardened Gauge Steel, DIN 2245 - Metav IndustryLine
Product data conflict detected: the item is marked both as "ausschuss" (scrap) and "gut" (good). This discrepancy in the classification of the product indicates an issue in the source data that needs immediate attention. Such conflicts can lead to errors in inventory management, production processes, and customer-facing documentation. Please verify the accuracy of the data and ensure consistency in the classification before proceeding. Correcting this issue is essential to avoid potential misunderstandings or operational disruptions. Once the source data has been reviewed and amended, a product description can be generated accurately and without further complications.
18 mm Measurement Balls Pair Hardened Chrome Steel 0.003 mm Accuracy, Tolerance 0.00008 mm - Metav IndustryLine
Benefit from precise reference geometry and high surface quality: the hardened chrome steel gauge ball pair delivers stable contact points and repeatable results, combining 18 mm diameter and 0.003 mm accuracy for reliable inspection tasks. Order the gauge ball pair directly via Metav Werkzeuge or ask our consultants if needed. Gauge Ball Pair M318.428 — 18 mm, 0.003 mm accuracy (Metav IndustryLine) The Gauge Ball Pair M318.428 serves as a precision reference for alignment, calibration and gauge-making tasks in inspection and metrology environments. Hardened chrome steel construction 0.003 mm geometric accuracy High surface quality Ra 0.00001 mm Delivered as a matched set of two Engineered reference points for repeatable inspection The set of precision spheres provides stable, well characterised contact points for comparative gauges and alignment rigs. Manufactured from hardened chrome steel and heat-treated to >HRC 62, the pair resists wear and maintains form under repeated loading, so fixtures and master gauges retain their reference over long service intervals. The combination of 18 mm diameter and a diameter tolerance of 0.00008 mm ensures that mounting and contact geometry remain consistent between measurements, reducing rework and inspection time. Measurable accuracy that integrates with production workflows Designed for metrology use, the spheres feature a declared accuracy of 0.003 mm, making them suitable as reference elements in calibration benches and comparative inspection tools. The exceptionally low surface roughness (0.00001 mm) reduces contact hysteresis and improves reproducibility when paired with tactile probes or optical comparators. Thanks to their compact mass (0.08 kg per set), the spheres are simple to handle while providing stable, repeatable results that support faster decision-making on the shop floor. Clear advantages for toolmakers and quality labs As a matched pair, the components simplify the setup of comparative gauges and go/no‑go fixtures: matched geometry reduces balancing and alignment steps during tooling changes. The robust chromium steel substrate and hardened finish lengthen service intervals and lower the frequency of replacements. For calibration and traceability, the items are supplied as a set, which supports controlled measurement chains in both production and laboratory contexts. Practical use cases and compatibility Typical applications include gauge fabrication, end‑of‑line inspection, spindle and fixture alignment, and reference points for CMM fixturing. The spheres are compatible with tactile probing systems and mechanical contact fixtures, where form accuracy and surface quality directly influence measurement uncertainty. The matched set format streamlines inventory and reduces downtime during fixture assembly. Contact Metav Werkzeuge for the Metav IndustryLine gauge ball set M318.428 to discuss calibration certificates, delivery options and suitability for specific inspection setups. Technical Data Article number: M318.428 GTIN: 4054469184166 SKU: M318.428 Facts Diameter: 18 mm Accuracy: 0.003 mm Diameter tolerance: 0.00008 mm Weight (set): 0.08 kg Special features Material: hardened chrome steel Hardness: >HRC 62 Surface roughness: 0.00001 mm Set: 2 balls FAQ What accuracy can be expected from these gauge balls? The Metav IndustryLine gauge ball pair offers a declared accuracy of 0.003 mm, making the spheres suitable as reference elements in calibration benches and inspection fixtures. Are the spheres supplied as a matched pair? Yes, the set is delivered as two matched precision spheres (set of two), which simplifies assembly of comparative gauges and alignment fixtures. Which materials and hardness apply to these balls? The balls are manufactured from hardened chrome steel with a hardness exceeding HRC 62, providing high wear resistance for repeated contact measurements. Can these balls be used with tactile probes and CMMs? The high surface quality and tight geometric tolerance make the spheres compatible with tactile probing systems and mechanical fixtures used in dimensional inspection. Is traceability or calibration documentation included? Calibration or traceability documentation details can be requested; contact Metav Werkzeuge for specific certificates and calibration options related to the Metav IndustryLine set. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
18 mm Setting Ring Form C Hardened Gauge Steel DIN 2250, DIN 286 JS3 - Metav IndustryLine
Combine precise Form C geometry, hardened and lapped gauge steel, and DIN‑certified tolerances for repeatable setting and verification of inspection equipment. Order the setting ring directly via Metav Werkzeuge or request application advice from our specialists to ensure the correct gauge solution for the task. Setting ring 18 mm M313.018 — hardened gauge steel, DIN 2250, Form C (Metav IndustryLine) A setting ring 18 mm engineered for accurate gauge setting and verification in inspection and toolroom environments, compliant with DIN 2250 and DIN 286. Hardened and lapped gauge steel construction Conforms to DIN 2250 and DIN 286, JS 3 Form C geometry for ring gauges Consistent tolerances for reliable repeatability The ring is manufactured from hardened and lapped gauge steel, a combination that ensures stable dimensions and minimal wear during repeated use. Conformity with DIN 2250 and DIN 286 in tolerance class JS 3 means the component offers verified limits that workshops and quality departments can rely on for traceable adjustments. In practice, this reduces rework and shortens setup times when aligning pins, gauges or plug-based measurement references. Durable finish and geometry that aids handling A lapped surface finish improves contact fidelity and reduces micro‑abrasion under repeated seating, while the Form C design provides a practical seating geometry for most ring‑gauge applications. The material selection and finishing processes deliver long service life and predictable behaviour in inspection routines, lowering the need for frequent replacement and maintaining measurement integrity in regular production checks. Integration into inspection workflows and tooling Ring gauges of this type are primarily used for setting master gauges, verifying plug gauges, and aligning measuring fixtures in toolrooms and inspection benches. The compact 18 mm diameter suits small to medium hole checks and provides a stable reference for calibration benches and in‑process controls. Delivered as a precision manufactured gauge, the component supports a streamlined quality workflow and clear documentation when incorporated into inspection plans. Contact Metav Werkzeuge for application guidance or to confirm availability of the Metav IndustryLine setting ring M313.018 at our Emmerich centre Technical data SKU: M313.018 GTIN: 4054469120560 Customs tariff number: 90173000 Facts Diameter: 18 mm eClass: 21170104 Special features Material: hardened and lapped gauge steel Standards: DIN 2250; DIN 286; tolerance class JS 3 Geometry: Form C Category: Gauges / Inspection tools FAQ What standards does this setting ring meet? The setting ring meets DIN 2250 and DIN 286 requirements and is manufactured to tolerance class JS 3, ensuring conformity for inspection and setting tasks with the Metav IndustryLine M313.018. What is the intended use of this ring gauge? This ring is intended for gauge setting, verification of plug gauges and as a stable reference in toolroom and inspection bench applications; the Form C geometry facilitates reliable seating. Which material is used for the setting ring? The component is made from hardened and lapped gauge steel, chosen for dimensional stability and wear resistance in repeated measurement operations. Is the setting ring suitable for production environment use? Yes, the robust finishing and conformity to DIN standards make the ring suitable for routine production inspection and calibration tasks where repeatable references are required. How can availability and application questions be clarified? For availability and specific application advice regarding the Metav IndustryLine setting ring M313.018, contact Metav Werkzeuge for technical guidance and procurement options. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
18,52mm Messstift, Länge 50mm, Werkstatt-Ausführung - Metav IndustryLine
Kompakte Kombination aus Präzision und robuster Werkstatt-Ausführung: Der Prüfstift liefert mit ±0,002 mm hohe Messsicherheit bei Endmaß‑Kontrollen und überzeugt durch die platzsparende Länge von 50 mm; bestellen Sie den Prüfstift direkt über Metav Werkzeuge oder fragen Sie unsere Beratung bei Bedarf an. Prüfstift, einzeln, 18,52 mm Länge 50 mm Der Prüfstift, einzeln, 18,52 mm Länge 50 mm ist ein kompakter Prüfbolzen für präzise Endmaß‑Kontrollen und eignet sich besonders für anspruchsvolle Werkstatt‑ und Fertigungsaufgaben. Werkstatt-Ausführung, robust und langlebig Spezial-Stahl für hohe Verschleißfestigkeit Präzision ±0,002 mm für zuverlässige Kontrolle Kompakte Länge 50 mm, platzsparend einsetzbar Lieferung in Kiste für sicheren Transport Hohe Materialqualität für langlebige Messungen Durch den Einsatz von Spezial-Stahl bietet der Prüfstift eine hohe Verschleißfestigkeit und sichere Oberflächeneigenschaften, die die Standzeit im täglichen Werkstattbetrieb erhöhen. Das kompakte Gewicht und die robuste Ausführung reduzieren das Risiko von Beschädigungen bei Handhabung und Einlagerung, sodass weniger Austauschzyklen anfallen und damit Laufzeitkosten gesenkt werden. Präzision, Messbereich und Einordnung für Feinmessung Mit einem Messbereich von 18,52 mm und einer spezifizierten Genauigkeit von ±0,002 mm wird die Komponente klar in die Mikro‑Kategorie (10–100 mm) eingeordnet, die sich für feinmechanische Arbeiten und Endmaß‑Prüfungen empfiehlt. Der Prüfstift ermöglicht reproduzierbare Ergebnisse bei der Kontrolle von Passungen und Bohrungsmaßen und ist damit ein zuverlässiges Werkzeug für anspruchsvolle Messaufgaben. Praktische Einsatzbereiche und Zielgruppen Der Prüfstift richtet sich an Werkstätten, Messlaboratorien und Qualitätssicherungsstellen, die robuste Prüfmittel für Serien‑ und Einzelprüfungen benötigen. Maschineneinrichter und Montagefachkräfte profitieren von der werkstattgerechten Bauart, während Fertigungsprüfer die hohe Präzision für schnelle Freigabemessungen nutzen können. Handhabung, Transport und Lieferumfang Die kompakte Länge von 50 mm und das geringe Gewicht von 0,15 kg erleichtern die Handhabung und das Einlegen in Prüfaufbauten. Die Lieferung erfolgt in einer Kiste (Kunststoff‑ oder Holzkiste), die sicheren Transport gewährleistet und Beschädigungen während der Logistik minimiert. So ist der Prüfstift sofort einsatzbereit und geschützt beim Versand. Für präzise Endmaß‑Kontrollen empfehlen wir den Prüfstift von Metav IndustryLine; bestellen Sie über Metav Werkzeuge oder kontaktieren Sie die Beratung per eMail info@metav-werkzeuge.com oder Telefon +49 2822 7131930 Produktmerkmale Artikelnummer: M323.I52 Marke: Metav IndustryLine Bezeichnung: Prüfstift, einzeln, 18,52 mm Länge 50 mm GTIN: 4061905449383 eClass: 21170231 Zahlen Messbereich: 18,52 mm Länge: 50 mm Gewicht: 0,15 kg Genauigkeit: ±0,002 mm Besonderheiten Material: Spezial-Stahl Werkstatt-Ausführung Verpackung: Lieferung in Kiste (Kunststoff- oder Holzkiste) SKU: M323.I52 FAQ Ist der Prüfstift für wiederholte Serienprüfungen geeignet? Der Prüfstift von Metav IndustryLine ist wegen der robusten Werkstatt-Ausführung und der Genauigkeit von ±0,002 mm gut für wiederholte Serienprüfungen geeignet und liefert konstante Ergebnisse bei Endmaß‑Kontrollen. Welche Vorteile bietet der Spezial-Stahl gegenüber Standardwerkstoffen? Spezial-Stahl beim Prüfstift erhöht die Verschleißfestigkeit und reduziert die Notwendigkeit häufiger Nachbearbeitungen, sodass Messzyklen länger stabil bleiben und die Betriebskosten sinken. Wie beeinflusst die kompakte Länge die Montage in Prüfaufbauten? Die Länge von 50 mm macht den Prüfstift sehr handlich und platzsparend, dadurch lässt er sich einfach in Prüfstände und Vorrichtungen integrieren, ohne zusätzliche Anpassungen an der Messumgebung. Wird der Prüfstift mit einer Schutzverpackung geliefert? Ja, der Prüfstift wird in einer Kiste geliefert, die für sicheren Transport sorgt und das Werkzeug beim Versand schützt. Hersteller: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
18.01mm Gauge Pin 50mm Length Workshop Version - Metav IndustryLine
Take advantage of a workshop‑rated gauge pin that combines precision and robust material for reliable fit checks and end‑measurements; with a nominal diameter of 18.01 mm and a compact 50 mm length this single gauge pin supports repeatable verification tasks — order directly via Metav Werkzeuge or consult our specialists for application advice. Gauge pin, single, 18.01 mm, length 50 mm — Metav IndustryLine workshop version A gauge pin for accurate end‑measurement and fit testing in workshop and inspection applications Precision tolerance ±0.002 mm Diameter 18.01 mm nominal fit Length 50 mm workshop version Delivered in transport box Repeatable fit checks with workshop robustness A compact inspection pin designed for routine verification: the solid construction provides a stable datum for plug and hole testing while the tight tolerance of ±0.002 mm ensures measurements that reduce rework and production interruptions. The small form factor and manageable mass aid fast handling during batch checks, making the component suitable for repetitive verification tasks in assembly, jigs and maintenance operations. Durable construction for everyday use Manufactured from special steel, this workshop version is finished to withstand frequent use in industrial environments. The chosen material delivers a balance between wear resistance and machinability, so the pin preserves its diameter and running condition under normal workshop handling. Supplied as a single gauge pin with a 50 mm usable length, it is suited to inspection benches where tool resilience and straightforward replacement are priorities. Integrates into existing inspection routines The nominal 18.01 mm diameter corresponds to standard fit checkpoints, allowing simple substitution into existing gauge sets or fixtures without elaborate adaptation. Delivered in a transport box for secure handling, the item is straightforward to store and move between stations. Traceability is supported by the clear manufacturer and article identifiers included in the technical information, simplifying inventory management and calibration scheduling. Practical benefits that matter on the shop floor Beyond metrological performance, the workshop edition prioritises efficiency: rapid identification of out‑of‑tolerance conditions reduces downstream scrap and streamlines quality gates. The combination of precision and robust finish makes this pin an economical choice for technicians and inspectors who need dependable reference elements that perform day after day. Contact Metav Werkzeuge for availability and technical advice on Metav IndustryLine gauge pins: call +49 2822 7131930 or email info@metav-werkzeuge.com Technical data Article number: M323.I01 GTIN: 4061905071027 Brand: Metav IndustryLine Material: Special steel Facts Diameter: 18.01 mm Length: 50 mm Tolerance: ±0.002 mm Weight: 0.15 kg Special features Workshop version Delivered in transport box for transport Category: Gauge pins / Messstifte FAQ What tolerance can be expected from this gauge pin? The gauge pin M323.I01 is specified with a tolerance of ±0.002 mm, enabling fine verification work and repeatable fit checks. Is the pin suitable for use in jigs and fixtures? Yes, the workshop‑rated construction and the nominal 18.01 mm diameter make the pin appropriate for integration into fixtures, gauges and portable inspection tools. What material is used and how does it affect wear resistance? The pin is made from special steel, chosen to provide a good balance between hardness and serviceability for everyday workshop usage. How is the item delivered and stored? The gauge pin is supplied as a single item and delivered in a transport box to protect the datum and maintain condition during handling and storage. Does the product include calibration certificates? No calibration certificate is indicated in the product data; calibration status should be confirmed separately if a traceable certificate is required for metrological use. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
18.03mm Gauge Pin 50mm Length Workshop Finish - Metav IndustryLine
Take advantage of the combination of workshop‑grade construction, narrow tolerance and compact geometry to ensure reproducible end‑measurements; order the part directly via Metav Werkzeuge or consult our specialists for application advice. M323.I03 Gauge pin — Ø 18.03 mm, 50 mm length (Metav IndustryLine) The M323.I03 gauge pin provides a compact, high‑precision reference for dimensional checks and end‑measurement tasks in workshop and production environments. Single gauge pin Ø 18.03 mm, 50 mm length Tolerance ±0.002 mm for precise checks Workshop‑grade special steel construction Supplied as an individual precision test pin Reliable dimensional control for repetitive checks The M323.I03 is designed for consistent size verification where repeatability matters. With a nominal diameter of Ø 18.03 mm and a tolerance of ±0.002 mm, this gauge pin enables fine dimensional discrimination in routine inspection tasks and assembly controls. The compact 50 mm length and single‑piece supply make it suitable for insertion, seating and comparative checks in fixtures and gauges. By converting a dimensional requirement into a simple, repeatable mechanical reference, the pin reduces measurement uncertainty and accelerates go/no‑go decisions in the workshop. Material choice and handling benefits Manufactured from special steel, the pin combines dimensional stability with wear resistance expected in frequent use. The material selection and workshop design minimise surface damage during handling and preserve the working diameter over many cycles. At 0.15 kg the pin is easy to position in jigs or test fixtures while remaining robust enough for everyday metrology tasks. These attributes support efficient inspection sequences and reduce the need for frequent rechecking, contributing to measurable time savings on repetitive operations. Integration into quality processes and traceability As a precision test pin, this item fits directly into established inspection flows and can serve as a reference for plug gauges, seating checks and end‑mass validation. Clear specification of Ø 18.03 mm and ±0.002 mm tolerance simplifies documentation and acceptance criteria for quality records. The compact form factor also permits easy storage and labelling alongside existing tooling. For applications requiring tailored measurement strategies, the Metav IndustryLine portfolio and advisory service help align the pin with fixtures and calibration intervals to maintain traceable, auditable results. Choose the Metav IndustryLine gauge pin for dependable workshop measurement and contact Metav Werkzeuge in Emmerich at info@metav-werkzeuge.com or +49 2822 7131930 for technical guidance or a quotation Technical data Article number: M323.I03 GTIN: 4061905071041 Manufacturer: Metav IndustryLine Description: Gauge pin, single, Ø 18.03 mm, length 50 mm Core specifications Diameter: 18.03 mm Length: 50 mm Tolerance: ±0.002 mm Weight: 0.15 kg Materials and special features Material: Special steel Workshop version (Werkstatt‑Ausführung) Supplied individually eClass: 21170231 FAQ What accuracy can be expected from this gauge pin? The M323.I03 gauge pin is specified with a tolerance of ±0.002 mm, making it suitable for fine workshop checks and repeatable dimensional comparisons. Is the pin suitable for use in fixtures and jigs? Yes, the compact 50 mm length and single‑piece construction make the pin appropriate for seating in fixtures, test blocks and comparative gauges. What material is the gauge pin made from? The pin is produced from special steel, chosen for dimensional stability and wear resistance in routine inspection environments. Can this gauge pin be used for end‑measurement of shafts or bores? The M323.I03 is intended as a precision reference for end‑measurement tasks and can be used for checking bores and mating components where the specific nominal diameter applies. How should the pin be stored and handled to preserve accuracy? Store the pin in a clean, dry environment and avoid impact to the working diameter; regular visual inspection and controlled handling will help maintain the specified tolerance. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
18.04mm Gauge Pin Length 50mm Workshop Version, Special Steel - Metav IndustryLine
Taking advantage of high repeatability, ±0.002 mm positional accuracy and a robust 50 mm working length ensures reliable end‑measure checks and reduced rework in fixture and gauge applications; order the gauge pin directly via Metav Werkzeuge or contact our consultants for technical advice. Gauge pin M323.I04 — 18.04 mm diameter, 50 mm length (Metav IndustryLine) A gauge pin for precise end‑measure verification and fixture alignment, engineered for workshop conditions High accuracy ±0.002 mm Diameter exactly 18.04 mm 50 mm working length for fixture checks Workshop version with transport case Precision that reduces measurement uncertainty Manufactured for measurement tasks demanding repeatable results, this gauge pin combines a nominal diameter of 18.04 mm with a verified positional tolerance of ±0.002 mm, delivering a stable reference for end‑measure and alignment operations. The tight tolerance reduces the need for rework by improving the match between component and fixture dimensions; when used as a reference mandrel or plug, the pin minimises cumulative errors in assembly and inspection processes. The numerical specification provides a clear basis for process control and quality documentation. Built for workshop handling and repeatability The component is produced in special steel and configured as a workshop version, which balances surface fidelity and robustness for routine use. With a 50 mm usable length, the pin is long enough for many fixture and clamp checks while remaining easy to handle and position. Supplied in a protective transport case, the item arrives ready for storage and safe transfer between workstations, preserving calibration and surface condition. The construction supports stable seating in gauges and holders, reducing slippage and improving repeat measurements. Practical integration with inspection workflows Designed as a single inspection pin suitable for bench and fixture use, the item serves as a reference element in assembly checks, go/no‑go verification and end‑measure assessments. The simple geometry and standard diameter make it compatible with common gauges and holders; traceable identification via SKU M323.I04 and GTIN supports inventory and documentation routines. Metav IndustryLine’s distribution through Emmerich provides dependable availability and a quality filter for the European market, helping workshops and production lines access precision tools without excessive procurement overhead. For a reliable workshop reference choose the Metav IndustryLine gauge pin and contact Metav Werkzeuge for availability and application guidance at +49 2822 7131930 or info@metav-werkzeuge.com Technical data Article number: M323.I04 GTIN: 4061905071058 Manufacturer: Metav IndustryLine Facts Diameter: 18.04 mm Length: 50 mm Weight: 0.15 kg Accuracy: ±0.002 mm Special features Material: special steel Workshop version Supplied in protective transport case Category: gauge pins FAQ What level of accuracy can be expected from this gauge pin? The gauge pin M323.I04 offers an accuracy of ±0.002 mm, making it suitable for tight end‑measure and alignment checks in workshop environments. Is the pin delivered ready for use and how is it packaged? The single gauge pin is supplied in a protective transport case to preserve its surface and dimensional integrity during storage and transport. Which materials and applications is the pin intended for? Made from special steel, the pin is intended as a hard reference for fixture checks, plug‑type verifications and end‑measure assessments in general metalwork and assembly tasks. Can this pin be used with standard holders and gauges? Yes, the nominal 18.04 mm diameter and straight cylindrical form make the pin compatible with common holders and inspection fixtures; identification by SKU M323.I04 aids integration into inventory systems. Does Metav IndustryLine provide product traceability information? Traceability is supported via SKU and GTIN; for extended documentation requirements please request specific inspection or trace reports when ordering. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
Fast, tactile checks where electronics are impractical
Gauges and test pins provide unequivocal go/no-go results for threads, bores, gaps and radii without relying on electronics. The range covers plug gauges and ring gauges for internal and external threads, feeler gauges and precision feeler strips for micro‑gap assessment, plus probe pins and measuring pins for tactile diameter and pitch checks.
How these tools work in the production environment
Mechanical gauges operate as direct reference standards: a plug gauge or ring gauge verifies conformity to thread profiles and mating ability, while limit gauges separate accept from reject in a single step. Test pins are used to tactilely measure small bore diameters, centre‑to‑centre distances and radii. Manufactured from hardened gauge steel or ceramic and often precision lapped, these instruments deliver immediate physical results that are ideal for incoming inspection, machine‑side checks and final control.
Measurable benefits that affect production performance
- Reduced scrap and rework through rapid, unambiguous pass/fail assessment.
- Increased repeatability thanks to very low measurement uncertainty and fine lapping.
- Lower downtime: quick checks at the machine save cycle time and reduce setup periods.
- Durable construction with high wear resistance from specialised, low‑distortion alloys.
- Versatile delivery formats: individual gauges, organised sets in wooden cases or metre‑length feeler rolls compliant with DIN 2269.
Why Metav is the practical choice for precision supplies
Metav combines decades of expertise with a broad warehouse and quality filtering from Emmerich. As a precision partner for industry, craft and trade, Metav supplies a comprehensive selection of gauges and test pins alongside complementary tools such as precision calipers and setting rings. With over 48,000 customers and a catalogue exceeding 250,000 items, Metav is positioned to supply reliably, reduce vendor complexity and support traceable quality control to national standards.
Summary
Gauges and test pins are indispensable for dependable, repeatable quality assurance where tactile, mechanical verification is preferred. Choose these plug gauges, ring gauges, feeler strips and probe pins when immediate, robust measurement decisions are required on the shop floor.
FAQ
What materials are gauges and test pins typically made from?
Gauges and test pins are usually manufactured from hardened gauge steel for durability and wear resistance; ceramic variants are available where thermal stability and minimal wear are critical.
How do thread gauges ensure mating capability?
Thread plug gauges and ring gauges check flank diameters and thread form against standards, providing a clear go/no‑go verdict that confirms pairability with mating parts.
Which tolerance class should I choose for probe pins and gauge sets?
Select tolerance classes aligned with your inspection requirements; for high‑precision tasks, sets produced to DIN 2269 or equivalent tolerance classes ensure micrometre‑level control and repeatability.
Can feeler gauges measure contact gaps in valve and engine work reliably?
Yes. Feeler gauges and precision feeler strips, supplied either as a fan or metre‑length rolls, allow accurate assessment of valve clearances and contact gaps down to micrometre increments.
How do limit gauges speed up in‑process inspection?
Limit gauges separate good from bad in a single, tactile operation, enabling rapid go/no‑go checks at the machine and reducing both inspection time and the likelihood of human interpretation errors.
Fragen zu diesen Produkten??
Mit mehr als 30 Jahren Erfahrung beraten wir Sie gerne persönlich.
Tel.: +49 2822 7131930
Mail: info@metav-werkzeuge.com