Precision gauge blocks and plug gauges for reliable dimensional control
Mechanical gauge blocks and plug gauges are essential for tactile verification of threads, bores and gap dimensions, providing fast, unambiguous go/no-go results that enhance process reliability and reduce scrap. Designed for industrial metalworking and toolmaking, these precision tools support incoming inspection and final quality checks by delivering traceable measurements in applications such as thread inspection, bore diameter testing and spacing checks. Manufactured from specially hardened, low-distortion alloys and fine-lapped for minimal measurement uncertainty, the range includes thread plug gauges, precision plug gauges and calibration gauge blocks to ensure long-term repeatability and wear resistance.
18.83mm Gauge Pin 50mm Length Workshop Version - Metav IndustryLine
Take advantage of a compact, workshop‑grade gauge pin that delivers consistent end‑dimension checks thanks to its precise Ø 18.83 mm diameter and ±0.002 mm tolerance; the robust special steel construction and 50 mm length ensure stable seating in fixtures and repeatable results—order through Metav Werkzeuge or request specialist advice from Metav consultants. Gauge pin M323.I83 – inspection pin, Ø 18.83 mm, length 50 mm (Metav IndustryLine) A gauge pin M323.I83 designed for precise end‑dimension verification and fixture alignment in workshop and production metrology. Workshop version, robust design Ø 18.83 mm for end‑dimension checks Length 50 mm for fixture alignment Made from special steel Reliable verification for end‑dimension checks The compact inspection pin provides a stable reference for end‑dimension checks and final inspection steps in component manufacturing. With a nominal Ø 18.83 mm and a stated tolerance of ±0.002 mm, the pin offers a repeatable datum for checking seats, bores and mating parts. The clear numeric specification and simple geometry reduce interpretation effort during quality assurance, enabling faster decisions in the measuring loop and fewer reworks. Workshop suitability and handling benefits Specified as a workshop version, the pin combines durability with straightforward handling. The 50 mm effective length suits fixture alignment and short‑reach gauges where rigidity and minimal deflection are essential. Its compact geometry simplifies insertion and extraction from jigs and gauges, so inspection cycles remain efficient even under frequent use. The single‑piece supply supports flexible inventory management for small series and maintenance tasks. Material choice and measurement confidence Manufactured from special steel, the pin maintains dimensional stability under typical workshop conditions and offers a balance of wear resistance and machinability. The declared measurement tolerance ±0.002 mm gives a clear expectation of fit and interchangeability, which simplifies specification sheets for production engineers and inspectors. The precise diameter and high material consistency reduce uncertainty when creating go/no‑go assemblies or when building gauge stacks. Integration into quality workflows As a straightforward inspection element, the pin integrates easily into existing gauge sets and fixture arrays. The simple form factor minimises sources of measurement error and supports rapid tactile verification as well as optical or machine‑assisted checks. Delivered as a single inspection pin with protective transport packaging, it is suitable for in‑line checks, fixture setup, and end‑of‑line acceptance testing where clear pass/fail criteria are required. Contact Metav Werkzeuge for application advice and reliable supply of the Metav IndustryLine gauge pin M323.I83—expert assistance from Emmerich ensures the right fit for production or maintenance tasks Technical data Article number: M323.I83 GTIN: 4061905449901 Material: Special steel Version: Workshop version Delivery: Protective transport case included Facts Diameter: 18.83 mm Length: 50 mm Tolerance: ±0.002 mm Weight: 0.15 kg Special features Single piece supply Intended for end‑dimension checks and fixture alignment Robust design for frequent workshop use FAQ What tolerance does the gauge pin offer? The gauge pin M323.I83 is specified with a tolerance of ±0.002 mm, making it suitable for precise end‑dimension verification in workshop and production settings. Which material is used for this inspection pin? This inspection pin is made from special steel, selected for dimensional stability and durability in workshop applications under Metav IndustryLine. What are the dimensions and weight of the pin? Nominal diameter is 18.83 mm with a length of 50 mm; the item weight is approximately 0.15 kg for handling and storage considerations. Is the pin suitable for fixture alignment and gauge stacks? Yes—its 50 mm length and precise diameter make the M323.I83 appropriate for fixture alignment, gauge stacks and end‑mass checks where a stable datum is required. How is the product delivered? The gauge pin is supplied as a single piece and shipped in a protective transport case to secure the item during transit Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
18.84mm Test Pin 50mm Length Workshop Version - Metav IndustryLine
Precision measurement with repeatable fit: 18.84 mm diameter, ±0.002 mm tolerance and robust special steel construction ensure reliable end‑measurement checks. Order the gauge pin directly via Metav Werkzeuge or consult our experts for application advice. Gauge pin M323.I84 — Single gauge pin, Ø 18.84 mm, 50 mm length (Metav IndustryLine) Gauge pin M323.I84 is a workshop-grade precision test pin for end‑measure checks and fitting tasks in mechanical assembly and quality control. Precise diameter 18.84 mm ±0.002 Special steel construction for durability 50 mm length for assembly and gauge blocks Delivered in a protective transport case Consistent fits for repeatable checks This single test pin delivers a consistent datum for go/no‑go checks and alignment tasks. The nominal 18.84 mm diameter with a verified ±0.002 mm deviation provides the level of repeatability demanded in series inspection and setup work, reducing trial adjustments and assembly rejects. Because the pin is manufactured from special steel, surface wear is limited and contact-induced distortion is minimised, which preserves measurement integrity during repeated use. Designed for workshop handling and inspection With a compact 50 mm working length the pin is optimised for confined spaces and fixture checks where a short, rigid gauge element is advantageous. The workshop execution balances stiffness and handling convenience, allowing rapid insertion and tactile confirmation of fit without elaborate fixturing. The design supports efficient process control: fewer interruptions, faster pass/fail decisions and clearer documentation of component conformity. Straightforward integration into QA routines The pin is suited to mechanical assembly, gauge setting and comparative checks within toolrooms and production lines. Traceable identification (SKU M323.I84, GTIN included in technical data) simplifies stock management and inspection records. Supplied in a protective transport case, the gauge reaches the bench ready for immediate use and safe storage between shifts, helping to maintain surface condition and dimensional reliability. Confidence through practical specification Specification-led selection reduces uncertainty in procurement: a compact test pin with a tight tolerance class supports both production monitoring and final inspection. The combination of measured accuracy, robust material and protective delivery results in a practical tool that supports throughput and lowers rework rates. For teams seeking predictable, workshop-ready measurement aids, this pin represents a pragmatic choice. For workshop-ready precision from Metav IndustryLine and supply from Metav Werkzeuge GmbH in Emmerich, request the gauge pin M323.I84 or contact our technical advisors at info@metav-werkzeuge.com or +49 2822 7131930 for application guidance and availability. Technical Data SKU: M323.I84 GTIN: 4061905449970 Weight: 0.15 kg Facts Diameter: 18.84 mm Length: 50 mm Tolerance: ±0.002 mm Special features Material: Special steel Version: Workshop execution Supplied in a protective transport case Category: Gauge pins FAQ What material is the pin made from? The gauge pin is produced from special steel, offering wear resistance and dimensional stability for routine inspection tasks. What tolerance does the pin meet? Tolerance is ±0.002 mm, providing a high level of repeatability suitable for fine inspection and assembly checks with SKU M323.I84. Can this pin be used for fixture alignment? Yes. The short, rigid 50 mm length and precise diameter make the pin suitable for fixture alignment and go/no‑go verification in workshop environments. How is the pin supplied for storage and transport? The pin is supplied in a protective transport case to safeguard the measuring surface during storage and movement. Is the gauge pin appropriate for micro‑component checks? With its compact dimensions and tight tolerance, the pin is well suited to fine mechanical tasks and small assembly verifications. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
18.85mm Gauge Pin Length 50mm Workshop Version - Metav IndustryLine
Precision‑engineered for repeatable end‑dimension verification, the gauge pin combines special steel construction with a nominal diameter of 18.85 mm, a 50 mm usable length and a manufacturing tolerance of ±0.002 mm for consistent inspection results. Order the gauge pin directly via Metav Werkzeuge or ask our consultants if needed. Gauge pin, single 18.85 mm / 50 mm (Metav IndustryLine) A gauge pin (18.85 mm, 50 mm length) intended for precise end‑measure checks, fixture set‑up and workshop inspection tasks. Workshop version for robust use Diameter 18.85 mm with ±0.002 mm tolerance 50 mm hardened special steel design Supplied individually for targeted checks Reliable dimensional control for end measurements The gauge pin M323.I85 is made for exacting inspection tasks where repeatability matters. With a nominal size of 18.85 mm and a tight tolerance of ±0.002 mm, this test pin delivers consistent reference geometry for go/no‑go checks, alignment of bore gauges and verification of end dimensions. The short, straight geometry reduces bending and ensures stable seating in inspection fixtures, so measurement variance is minimised and process capability improves. Robust material choice and workshop durability Manufactured from special steel and finished for workshop use, the pin is intended to withstand frequent handling and contact with hardened seating surfaces. The choice of material gives high wear resistance and dimensional stability during repeated cycles of insertion and withdrawal. The 50 mm shaft length provides sufficient engagement for typical bench fixtures while remaining easy to handle and position during rapid checks. Practical integration into inspection workflows Designed as an individual reference pin, this test piece is well suited to in‑process control and fixture calibration. The smooth cylindrical form supports reliable seating in bushings or gauging sockets, and the clearly defined nominal size aids quick traceability on inspection lists. Inclusion of the GTIN ensures easy stock management and line item identification in procurement and quality documentation. Benefits for throughput and quality assurance Using a dedicated gauge pin reduces adjustment time and lowers the risk of operator‑induced variance during inspection. The combination of tight tolerance and durable construction helps to avoid unnecessary rework, supporting higher first‑pass yield and a more efficient quality routine. For workshop and small‑batch environments, the compact design also aids storage and fast deployment at the inspection point. Contact Metav Werkzeuge to discuss suitability for specific inspection rigs, request delivery details or reserve stock of the Metav IndustryLine gauge pin for faster, more reliable end‑measure verification from Emmerich. Technical data SKU: M323.I85 GTIN: 4061905070273 Label: Gauge pin, single, 18.85 mm diameter, 50 mm length Facts Nominal diameter: 18.85 mm Length: 50 mm Tolerance: ±0.002 mm Weight: 0.15 kg Special features Material: Special steel Version: Workshop execution Supplied individually FAQ What applications is this gauge pin intended for? This gauge pin is intended for end‑dimension verification, fixture set‑ups and go/no‑go checks in workshop and inspection environments. What is the declared tolerance and how does it affect measurements? The declared tolerance of ±0.002 mm ensures high repeatability; the tight tolerance reduces uncertainty when the gauge pin is used as a reference in inspection routines. Is the material suitable for frequent use in production? Yes, the gauge pin is made from special steel and finished for workshop use, providing wear resistance suitable for frequent insertion and withdrawal. Can this pin be used in existing gauging fixtures? The 18.85 mm nominal diameter and standard cylindrical form allow compatibility with many existing sockets and gauges; the SKU M323.I85 helps to identify the exact item for fixture adaptation. How is the product identified for procurement and inventory? Identification is supported by the SKU M323.I85 and GTIN 4061905070273 for straightforward ordering and stock management. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
18.86mm Gauge Pin Length 50mm Workshop Version, Special Steel In Plastic Case - Metav IndustryLine
A compact gauge pin in special steel with a nominal diameter of 18.86 mm, 50 mm length and a tolerance of ±0.002 mm provides repeatable end‑dimension checks and reliable fit verification; supplied in a transport case for safe handling. Order the M323.I86 via Metav Werkzeuge or consult their advisers for application support. Gauge pin M323.I86 — single gauge pin, Ø 18.86 mm, 50 mm length (Metav IndustryLine) Gauge pin M323.I86, a single inspection pin for end‑dimension verification and fit testing in workshop metrology. Single gauge pin Ø 18.86 mm, length 50 mm Manufacturer tolerance ±0.002 mm Special-steel for robust wear resistance Supplied in transport case for secure storage Precision where measurement reliability reduces rework The M323.I86 is manufactured to a tight tolerance of ±0.002 mm, making it suitable for verification tasks where small deviations affect assembly quality. The 18.86 mm nominal diameter is produced with consistent roundness and surface finish to ensure reproducible contact points during inspection. This level of control reduces the need for repeated checks and supports quality assurance processes by providing a measurable reference for end‑dimension and bore verification. Durable construction for demanding workshop use Constructed from special steel, the pin is designed to withstand frequent handling and the abrasive conditions of a busy workshop. The 50 mm length provides stable engagement in holes or mating components while minimising deflection during inspection. The item is offered in a workshop version, optimised for routine use, and is supplied in a transport case to protect the gauge during storage and transit. These attributes together extend service life and maintain measurement integrity over many inspection cycles. Small-format gauge for fine mechanical and component checks This product falls within the micro range (up to 100 mm) of inspection tools, making it ideal for fine mechanical tasks and compact components where a short, rigid pin is required. The compact format supports ease of handling and fast set‑up on benches and fixtures commonly found in metalworking and precision engineering shops. As a single gauge pin, it serves as a precise go/reference element for dimensional checks and assembly verification in production and maintenance workflows. Contact Metav Werkzeuge in Emmerich to discuss the M323.I86 and secure the right gauge pin for workshop inspection tasks — email info@metav-werkzeuge.com or call +49 2822 7131930 Technical data SKU: M323.I86 GTIN: 4061905070280 Manufacturer: Metav IndustryLine Label: Prüfstift, einzeln, 18,86 mm Länge 50 mm Core specifications Diameter: 18.86 mm Length: 50 mm Tolerance: ±0.002 mm Weight: 0.15 kg Special features Material: Special steel Version: Workshop execution Delivery: Supplied in a transport case Application: End‑dimension and fit checks FAQ What tolerance does this gauge pin offer? The M323.I86 gauge pin is manufactured to a tolerance of ±0.002 mm, providing high repeatability for end‑dimension checks and fit verification. What material is used for the inspection pin? The inspection pin is made from special steel, chosen for wear resistance and stable measuring behaviour under regular workshop use. Is the gauge pin delivered in protective packaging? Yes, the pin is supplied in a transport case to protect the gauge during storage and transit. Which measurement tasks suit this small gauge pin? This compact pin is intended for micro‑range inspection tasks — end‑dimension verification, bore and fit checks on small components typical in precision engineering and metalworking. Does the product include a calibration certificate? The product data does not specify a calibration certificate; the pin is supplied with the stated manufacturing tolerance of ±0.002 mm as the technical specification. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
18.87mm Test Pin, Single, 50mm Length, Workshop Version - Metav IndustryLine
Take advantage of the combination of workshop robustness, tight ±0.002 mm tolerance and a compact 50 mm length for reliable end‑dimension checks; order the test pin directly via Metav Werkzeuge or ask our consultants for application advice. M323.I87 Test Pin — Single precision test pin, Ø 18.87 mm, 50 mm length (Metav IndustryLine) M323.I87 is a single precision test pin intended as an end‑dimension reference for workshop metrology, compatible with gauge blocks and fixture checks. Workshop execution for everyday metrology Precision tolerance ±0.002 mm Solid special-steel construction Compact 50 mm length for fixture work Precision where it matters: accurate reference for end‑measurements The M323.I87 functions as a dedicated reference pin for end‑dimension verification and small‑batch inspections. With a nominal diameter of Ø 18.87 mm and a declared accuracy of ±0.002 mm, the pin delivers the repeatability required for tight tolerance checks and routine quality control. The tight tolerance is particularly useful when validating assembly fits, seating surfaces or measuring against calibrated master gauges. The compact geometry and consistent diameter reduce alignment error, providing a reliable tactile and dimensional reference in workshop environments. Robust design for daily workshop use and fast set‑up Manufactured from special steel, the pin combines material strength with a finely finished contact surface that resists wear during repeated use. The 50 mm nominal length balances reach and rigidity, making the component easy to handle and position in fixtures or measuring stands while maintaining profile stiffness. At approximately 0.15 kg, the solid construction feels substantial without being unwieldy, aiding stable placement during checks. This pragmatic design reduces set‑up time and contributes to efficient inspection cycles on the shop floor. Confidence through a trusted supply chain and proven service As part of the Metav IndustryLine, this test pin benefits from a vendor focus on accessible precision: well‑maintained stockholding in Emmerich and a broad metrology range for matching accessories. Metav’s established offering and inventory depth help streamline procurement and reduce supply‑chain risk for production or maintenance teams. The combination of pragmatic engineering and vendor reliability delivers a component that supports reproducible measurement outcomes and steady workshop throughput. For workshop-grade measurement needs, request the Metav IndustryLine M323.I87 precision test pin via Metav Werkzeuge — our Emmerich team can advise on compatibility with existing gauges and supply logistics Technical Data Article number: M323.I87 GTIN: 4061905071171 Brand: Metav IndustryLine Weight: 0.15 kg Material: Special steel Facts Diameter: 18.87 mm Length: 50 mm Tolerance: ±0.002 mm Weight: 0.15 kg Special features Workshop execution Single test pin Designed for end‑dimension checks Compact design for fixture use FAQ What are the nominal diameter and length of this test pin? The M323.I87 test pin has a nominal diameter of 18.87 mm and a length of 50 mm. What accuracy can be expected from the pin? The declared manufacturing tolerance for the pin is ±0.002 mm. What material is used for this component? The component is made from special steel, chosen for wear resistance and dimensional stability. For which applications is this pin suitable? The pin is intended for end‑dimension reference checks, fixture setup, and use as a gauge reference in workshop metrology. Is calibration information provided with the product data? Calibration is not specified in the supplied product data. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
18.88mm Test Pin 50mm Length Workshop Version, Special Steel - Metav IndustryLine
A compact, workshop-grade test artefact that combines 18.88 mm nominal diameter, 50 mm usable length and a fine ±0.002 mm tolerance to support reliable go/no-go checks and reference measurements; order the gauge pin directly via Metav Werkzeuge or ask our consultants if needed. Gauge pin M323.I88 — 18.88 mm diameter, 50 mm length (Metav IndustryLine) A gauge pin M323.I88 intended for precision bore checks and reference measurement tasks in workshop metrology and inspection. Precision tolerance ±0.002 mm Diameter 18.88 mm exact fit 50 mm ground length for stability Workshop-grade special-steel design Repeatable bore checks with micrometre-level control This test pin delivers a repeatable reference for bore verification, with a specified ±0.002 mm tolerance that defines its inspection suitability. The 18.88 mm nominal diameter is ground to provide a predictable fit in calibrated bores, making the component useful for go/no-go assessments and comparative gauging. Stating the tolerance as a measurable limit clarifies expected performance during setup and quality control activities and supports traceable decision-making in production. Material choice that withstands workshop use Constructed from special steel, the component is designed as a workshop-grade measurement element that resists routine wear while preserving surface integrity under normal handling. The material choice gives structural stiffness and long-term wear resistance, so dimensional stability is maintained across repeated insertions and withdrawals. Where bench tools and fixture checks demand robustness, this version balances durability with the dimensional precision required for inspection tasks. Compact length and clear traceability for fixture work A 50 mm usable length provides a stable engagement depth without excessive overhang, aiding reproducible seating in fixtures and jigs. The short form factor reduces bending effects during manual handling and supports stable reference surfaces for comparative measurement. Identification via M323.I88 and associated product codes ensures straightforward inventory control and process documentation for inspection routines, improving traceability within quality systems. For workshop-grade inspection components from Metav IndustryLine, contact Metav Werkzeuge in Emmerich for specification support and procurement assistance. Technical data SKU: M323.I88 GTIN: 4061905071188 Manufacturer: Metav IndustryLine Numbers / Core technical data Diameter: 18.88 mm Length: 50 mm Tolerance: ±0.002 mm Weight: 0.15 kg Eclass: 21170231 Design / Special features Material: Special steel Version: Workshop execution Item: Single gauge pin Story trigger: endmasse FAQ What is the dimensional tolerance of this gauge pin? The gauge pin M323.I88 is specified with a tolerance of ±0.002 mm, which defines its suitability for fine inspection and repeatable fit checks. Is the component suitable for use as a reference in fixture set-up? Yes; the 50 mm length and ground diameter make it suitable as a reference element for fixture alignment and comparative gauging. What material is used for this test pin? The test pin is manufactured from special steel, selected for its stiffness and resistance to wear in workshop environments. Is the part supplied as a single item or as a set? This article is supplied as a single gauge pin, designated under SKU M323.I88 for inventory and traceability. How should the gauge pin be managed within a quality system? Record the SKU and GTIN in inspection documentation, store the pin in a clean, dry environment and include it in routine verification checks to ensure ongoing dimensional reliability. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
18.89mm Gauge Pin 50mm Length Workshop Version - Metav IndustryLine
Take advantage of the combination of high reproducibility, robust workshop construction and tight dimensional control to ensure reliable end‑dimension checks in production and inspection. Order the gauge pin directly via Metav Werkzeuge or consult our specialists for application advice. Gauge pin M323.I89 — Gauge pin, Ø 18.89 mm, length 50 mm, Metav IndustryLine Gauge pin M323.I89 is a single test pin intended for precise end‑dimension verification and fit control in workshop and quality‑assurance environments Workshop‑grade special steel construction Diameter 18.89 mm, length 50 mm Dimensional accuracy ±0.002 mm Ideal for end‑dimension checking Precision where final fit matters The gauge pin M323.I89 is manufactured for repeatable, end‑dimension verification where small deviations matter. With a nominal diameter of 18.89 mm and a length of 50 mm, the pin provides a stable reference for bore checks, go/no‑go testing and comparative inspection tasks. The specified ±0.002 mm tolerance defines the allowable deviation and supports tight acceptance criteria in quality control procedures; in practice this level of accuracy shortens decision time at the inspection bench and reduces the risk of production rework. Robust workshop construction for daily use Made from special steel and produced in a workshop‑grade execution, the pin resists wear from repeated seating and withdrawal in bores and gauges. The solid construction translates into consistent contact conditions and therefore improved repeatability of measurements over time. At a handled weight of 0.15 kg the component is substantial enough to feel secure in use yet compact for bench storage. These attributes support uninterrupted inspection workflows and reduce the frequency of tool replacement. Practical handling and inspection applications Designed as a single test item for end‑dimension and fit control, the pin is suited to quick functional checks and integration into standard inspection jigs. Operators benefit from a simple, robust geometry that minimises measurement variables: the cylindrical reference surface concentrates the control task on diameter and concentricity, while the length provides a useful reference for short bores and seat depths. Where clear specification of final mating condition is required, this component offers a pragmatic, low‑complexity solution that complements calipers and plug gauges. Contact Metav Werkzeuge today to discuss how the M323.I89 gauge pin from Metav IndustryLine can be integrated into existing inspection routines or measurement fixtures Technical data Article number: M323.I89 GTIN: 4061905071195 Category: Gauge pins Facts Diameter: 18.89 mm Length: 50 mm Accuracy: ±0.002 mm Weight: 0.15 kg Special features Workshop version Single test pin Story trigger: end‑dimension checks FAQ What material is the pin made from? The gauge pin M323.I89 is manufactured from special steel, specified for workshop use and designed for mechanical durability in repeated inspection tasks. What is the dimensional tolerance of this test pin? The item delivers a dimensional accuracy of ±0.002 mm, making it suitable for tight end‑dimension verifications and fit assessments. Which inspection tasks is this pin suited to? The pin is intended for end‑dimension checks, bore verification and fit control where a precise cylindrical reference is required. What identifiers belong to this product? This product is listed as M323.I89 (SKU) with GTIN 4061905071195 and is part of the Metav IndustryLine gauge pin range. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
18.8mm Test Pin 50mm Length Workshop Version - Metav IndustryLine
Take advantage of robust workshop construction and high repeatability: the combination of Ø 18.8 mm diameter, 50 mm length and a stated dimensional accuracy of ±0.002 mm supports reliable end-measure checks and reduces rework. Order or request technical details via Metav Werkzeuge for rapid clarification. Inspection pin, single — Ø 18.8 mm, 50 mm length (Metav IndustryLine) The inspection pin is a workshop-grade test probe designed for precise end-measure verification and fixture checks in production and maintenance environments. Workshop-grade construction Diameter 18.8 mm for end-measure checks Length 50 mm for deep fixture access Dimensional accuracy ±0.002 mm Accurate end-measure control for reliable pass/fail decisions The probe delivers repeatable measurements thanks to its tight tolerance of ±0.002 mm, which supports consistent quality decisions on the shop floor. This level of precision minimises ambiguous results during incoming inspection or assembly control and contributes directly to reduced rework and improved first-pass yield. The stated accuracy is particularly relevant where small deviations translate into functional issues further down the production chain, so the pin functions as a compact, deterministic reference in gauging nests and check fixtures. Robust build for daily workshop handling Constructed from special steel and specified as a workshop execution, the probe withstands frequent handling and contact with toolroom environments while maintaining geometric integrity. With a 50 mm overall length it reaches into many fixture geometries without compromising stiffness, and the Ø 18.8 mm diameter provides a stable contact face for end-measure applications. The component's mass and geometry help reduce bending under normal use, which keeps measured values repeatable across many cycles and supports efficient, one-person handling in production or maintenance tasks. Traceable identification and simple integration into workflows The article is supplied individually and carries the stock identifier M323.I80 along with GTIN 4061905449871, enabling straightforward inventory control and traceability within existing procurement and quality-management systems. The probe integrates easily as a reference element in modular fixtures or as a spare gauge pin in inspection benches, providing a standardised, serviceable component that fits common workshop procedures. The use of familiar materials and dimensions keeps replacement and interchangeability uncomplicated across production lines. For dependable end-measure control in workshop environments, request a detailed data sheet from Metav Werkzeuge or enquire about batch availability from Metav IndustryLine via Metav Werkzeuge. Technical data SKU: M323.I80 GTIN: 4061905449871 Label: Prüfstift, einzeln, 18,8 mm Länge 50 mm Facts Diameter: 18.8 mm Length: 50 mm Weight: 0.15 kg Dimensional accuracy: ±0.002 mm Special features Material: special steel Workshop execution Supplied individually Category: test pins (Messstifte) FAQ What is the intended use for this inspection pin? This inspection pin is intended for end-measure verification and fixture checks in workshops and production lines, serving as a compact reference element for repeatable measurements. Which dimensions define the probe? The probe has a diameter of 18.8 mm and an overall length of 50 mm, identified in stock as M323.I80 for inventory and traceability. How precise is the component for gauging tasks? Dimensional repeatability is specified as ±0.002 mm, making the pin suitable for precise pass/fail inspections and routine fixture validation. Is the item traceable for procurement and quality records? Yes, the product is listed under SKU M323.I80 and GTIN 4061905449871 for straightforward traceability in quality and inventory systems. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
18.91mm Gauge Pin, Single, 50mm Length Workshop Version - Metav IndustryLine
Take advantage of a workshop-grade measuring solution that pairs high dimensional accuracy with robust construction for routine inspection tasks; the combination of Ø 18.91 mm diameter and ±0.002 mm tolerance ensures reproducible end‑dimension checks and reduces rework. Order the gauge pin directly via Metav Werkzeuge or ask our consultants for application advice. Gauge pin, single, 18.91 mm (length 50 mm) – workshop‑grade precision pin (Metav IndustryLine) The Gauge pin, single, 18.91 mm (length 50 mm) is a compact workshop instrument designed for precise end‑dimension verification and fixture alignment in metalworking and quality control environments. Precision diameter 18.91 mm Measuring length 50 mm High accuracy ±0.002 mm Workshop version with transport case Precision where small tolerances matter A compact measuring element delivers reliable, repeatable checks when manufacturing tolerances are tight. The M323.I91 gauge pin features a Ø 18.91 mm nominal diameter combined with a declared ±0.002 mm deviation, which provides measurable assurance for final‑dimension inspections. Classified in the micro range (measurement span within 10–100 mm), this size is ideal where short jaws and minimal deflection are beneficial: fine mechanical parts, small bores and delicate assemblies profit from the pin’s low bending tendency and consistent contact geometry. The clear numeric tolerance offers an immediate decision basis for acceptance or rework, supporting lean inspection routines. Robust workshop construction for everyday use Built as a workshop‑grade instrument, the pin is machined from special steel for wear resistance and dimensional stability under repeated use. The 50 mm working length balances insertion depth and handling comfort, while the compact mass (approx. 0.15 kg) makes placement and removal straightforward during batch sampling. Delivered in a dedicated transport case, the pin is protected in transit and storage — a practical detail that preserves calibration and surface condition between inspections. The construction emphasises durability without sacrificing the fine runout and concentricity required for reliable plug‑type gauging. Fits into established inspection workflows and tooling The gauge pin integrates seamlessly with existing fixtures, plug gauges and comparator setups, supporting repeatable checks at incoming inspection, in‑process control and final verification. Traceable identification (SKU M323.I91, GTIN available) simplifies inventory and quality records, while the precise nominal diameter reduces measurement uncertainty when used as a reference artefact. For production environments seeking to lower scrap rates and speed go/no‑go decisions, the pin acts as a simple, dependable standard that streamlines routine metrology tasks and improves throughput. Contact Metav Werkzeuge for tailored advice on workshop‑grade gauge pins and to ensure the right specification for the intended application; call +49 2822 7131930 or email info@metav-werkzeuge.com Technical data Article number: M323.I91 GTIN: 4061905071218 Label: Gauge pin, single, 18.91 mm length 50 mm Core specifications Diameter: 18.91 mm Length: 50 mm Accuracy: ±0.002 mm Weight: 0.15 kg Special features Material: Special steel Version: Workshop execution Delivery: Transport case Category: Gauge pins FAQ What is the declared tolerance of this gauge pin? The declared tolerance of the M323.I91 gauge pin is ±0.002 mm, suitable for fine end‑dimension verification in precision workshops. Is the pin supplied ready for use or does it require calibration? The gauge pin is supplied ready for use; standard factory tolerances apply and traceable identification (SKU M323.I91) is provided for quality records. Which applications is this pin best suited for? This workshop‑grade pin is suited to end‑dimension checks, fixture alignment and plug‑type verification of small bores and mechanical components. What material is the pin made from and why does it matter? The pin is manufactured from special steel to ensure wear resistance and dimensional stability under repeated use, preserving the nominal diameter during routine inspection. Can this pin be integrated into existing gauging fixtures? Yes, the M323.I91 gauge pin is compatible with standard fixtures and plug gauges, offering a compact reference for repeatable checks. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
18.92mm Gauge Pin, Special Steel, 50mm Length, Workshop Version, Supplied in Case - Metav IndustryLine
Combining workshop‑ready robustness, Special steel construction and a tight tolerance of ±0.002 mm makes this single gauge pin a reliable choice for repeatable end‑size checks; order the gauge pin directly via Metav Werkzeuge or ask our consultants if needed. Gauge pin M323.I92 — single precision pin, 18.92 mm Ø, 50 mm length | Metav IndustryLine M323.I92 is a single precision gauge pin designed for end‑size inspection and dimensional verification in workshop metrology. Workshop version for robust use Diameter 18.92 mm with ±0.002 mm precision 50 mm pin length for stable handling Made from Special steel for wear resistance Consistent accuracy that reduces rework The pin delivers a declared ±0.002 mm runout, providing a measurable reduction in inspection uncertainty for small‑bore and end‑size assessments. Placed in the Micro range (10–100 mm) classification, this single‑piece gauge is optimised for fine mechanical and workshop tasks where short measurement spans demand high stiffness and minimal deflection. The tight tolerance narrows the window for batch rejection and supports faster decision‑making in quality control. Built for the workshop: durable and easy to handle Constructed from Special steel, the component balances surface hardness with corrosion resistance for frequent use on the shop floor. The 50 mm length offers a tactile, controllable grip during manual checks while maintaining a compact form factor that resists twisting under hand pressure. These attributes translate into longer service life and fewer replacements, which benefits maintenance planning and keeps inspection throughput steady. Traceable hardware that fits production workflows With a clear SKU and GTIN: 4061905071225, the pin supports inventory management and traceability within a calibrated metrology environment. Intended for end‑size verification, the single gauge pin integrates simply with existing plug gauge sets or measuring fixtures and provides a straightforward reference for go/no‑go checks. The combination of workshop design and precise geometry helps maintain reproducible results across shifts and operators, contributing to measurable process stability. For application advice or to secure stock of the Metav IndustryLine M323.I92 gauge pin, contact Metav Werkzeuge in Emmerich for tailored recommendations and fast processing Technical Data Article number: M323.I92 GTIN: 4061905071225 Manufacturer: Metav IndustryLine Facts Diameter: 18.92 mm Length: 50 mm Tolerance / Accuracy: ±0.002 mm Weight: 0.15 kg Special features Material: Special steel Version: Workshop execution Type: Single gauge pin Intended use: End‑size inspection and dimensional verification FAQ What measurement accuracy can be expected from this pin? The gauge pin M323.I92 is specified with an accuracy of ±0.002 mm, suitable for high‑precision workshop checks and end‑size verification. Is the material suited to frequent use in a production environment? Yes, the M323.I92 is made from Special steel and supplied in a workshop execution intended to withstand regular handling and inspection routines. Which measurement category does this pin belong to? With a diameter of 18.92 mm, the pin falls into the Micro range (10–100 mm), making it suitable for compact, high‑precision measurements. Can this pin be used as a reference in plug gauge sets? The single precision pin is appropriate for integration into manual plug gauge checks and as a reference element for go/no‑go assessments. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
18.93mm Gauge Pin 50mm Length Workshop Version - Metav IndustryLine
Precision inspection assured by the combination of a ±0.002 mm tolerance and a special steel construction in a compact 50 mm length. Benefit from a robust workshop specification and straightforward procurement: order the gauge pin directly via Metav Werkzeuge or consult our specialists for application advice. Gauge pin M323.I93 — Ø 18.93 mm, 50 mm length (Metav IndustryLine) The gauge pin for quick dimensional checks and workshop inspection tasks, with a nominal diameter of 18.93 mm and an overall length of 50 mm. Precision tolerance ±0.002 mm Diameter Ø 18.93 mm 50 mm overall length, workshop version Special steel construction Accurate inspection that speeds up quality checks The compact design delivers repeatable results in routine inspection processes: a fine tolerance of ±0.002 mm ensures that pass/fail decisions and go/no-go evaluations can be made with confidence. The measured diameter of Ø 18.93 mm and the modest length reduce wobble during insertion, which helps preserve measurement integrity. As a single plug-style gauge pin, it is well suited for short-cycle checks on assemblies and components where quick verification is essential to maintain production flow. The combination of dimensional stability and clear nominal values supports faster decision-making on the shop floor and in incoming‑goods inspection. Robust material for regular workshop use Constructed from special steel, this gauge pin has been specified for durability under frequent handling. The material choice provides resistance against everyday wear and keeps surface integrity over many cycles of use, which in turn reduces the need for early replacement. The workshop execution (Werkstatt-Ausführung) indicates a build geared towards practical, hands-on environments where tools are expected to tolerate regular use without specialised handling. This makes the part economical for routine quality assurance tasks while still delivering the precision required for mechanical and metalworking contexts. Practical dimensions and handling benefits With an overall length of 50 mm and a weight of 0.15 kg, the pin is easy to position and manipulate in confined or awkward measurement situations. The compact length lowers leverage and the risk of deflection, thereby improving the reliability of short-range diameter checks. For operators, the modest mass and balanced geometry make insertion and extraction straightforward during repetitive checks, reducing operator fatigue and improving throughput. Where a single, precise reference diameter is needed, this component functions as a dependable, low‑complexity solution that integrates smoothly with standard inspection jigs and fixtures. Fit for purpose in inspection workflows The M323.I93 from Metav IndustryLine is designed as an individual gauge pin for direct use in workshop and inspection applications. Its nominal diameter and tight tolerance make it suitable for end‑dimension checks and for validating bore sizes where a single reference gauge is required. The clear specification simplifies part selection in purchasing and technical documentation, and the solid construction minimises downtime associated with tool replacement. For organisations seeking a pragmatic, accurate measuring aid, this gauge pin supports consistent quality monitoring in daily production routines. For precise inspection needs, contact Metav Werkzeuge to request the M323.I93 gauge pin and receive tailored application advice from our specialists in Emmerich. Technical Data Article number: M323.I93 GTIN: 4061905071744 Manufacturer: Metav IndustryLine Material: Special steel Weight: 0.15 kg Nominal diameter: 18.93 mm Overall length: 50 mm Tolerance: ±0.002 mm Core specifications Diameter Ø: 18.93 mm Length: 50 mm Tolerance: ±0.002 mm Weight: 0.15 kg Special features Workshop execution Single gauge pin (individual supply) SKU: M323.I93 Category: Gauge pins / Messstifte FAQ What tolerance does the M323.I93 gauge pin offer? The M323.I93 gauge pin from Metav IndustryLine is specified with a tolerance of ±0.002 mm for precise dimensional checks. What material is the gauge pin made from? The gauge pin is manufactured from special steel, chosen for wear resistance and suitability for regular workshop use. What are the dimensions and weight of the gauge pin? The pin has a nominal diameter of 18.93 mm, an overall length of 50 mm and a weight of 0.15 kg. Is the component supplied individually or as part of a set? This article is supplied as a single gauge pin (individual unit), intended for standalone inspection tasks. Which inspection tasks is this pin best suited to? The M323.I93 is suitable for quick pass/fail diameter checks, end-dimension verification and use as a reference gauge in workshop and incoming-inspection workflows. Metav IndustryLine: Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
18.94mm Gauge Pin 50mm Length Workshop Version - Metav IndustryLine
Take advantage of the combination of 18.94 mm nominal diameter, a 50 mm usable length and a tight tolerance of ±0.002 mm for consistent end‑measure verification in the workshop; order the gauge pin directly via Metav Werkzeuge or consult the team for application advice. Gauge pin, single — 18.94 mm diameter, 50 mm length (Metav IndustryLine) Gauge pin, single 18.94 mm is a workshop‑grade cylindrical gauge for precise end‑measure and insertion checks in production and inspection environments. Precision diameter 18.94 mm ±0.002 50 mm length for insertion and end checks Special steel for robust workshop use Workshop version supplied as a single piece Reliable verification for repetitive end measurements Designed for consistent use in production and inspection routines, this gauge pin offers a nominal diameter of 18.94 mm with a verified tolerance of ±0.002 mm, which minimises uncertainty when checking end measures or locating holes. The combination of tight dimensional control and a short, rigid shaft keeps repeatability high in fast assembly or inspection cycles. This makes the component particularly suitable where quick go/no‑go decisions or calibration references are required within a bench or machine environment. Robust build for frequent handling and insertion cycles Machined from special steel, the pin resists wear and maintains its gauge over many insertion cycles, reducing the need for frequent replacement and lowering process interruptions. The 50 mm length balances handling convenience with sufficient engagement depth for secure contact during checks. Surface finish and material selection aim to reduce burr formation and stick‑slip when entering fits, contributing to reliable tactile feedback during manual or fixture‑assisted inspection tasks. Practical workshop integration and traceable use The workshop execution emphasises straightforward integration into existing fixtures and measuring jigs used on the shop floor. Marking and SKU notation simplify inventory handling and traceability: this single gauge pin is identified as SKU M323.I94, making stock control and replacement planning convenient. Due to its focused design, it supports fast throughput in routine quality control and can serve as a reference element in setup procedures or comparative checks. Discuss application specifics with Metav Werkzeuge for a tailored recommendation based on the inspection task and fixture geometry Technical data SKU: M323.I94 GTIN: 4061905071751 Category: Gauge pins Version: Workshop version Numbers / Core technical data Nominal diameter: 18.94 mm Usable length: 50 mm Dimensional tolerance: ±0.002 mm Weight: 0.15 kg Materials & special features Material: Special steel Design: Single gauge pin for end‑measure verification Typical application: End‑measure and insertion checks Supply form: Single piece FAQ What is the nominal diameter and tolerance of this gauge pin? The gauge pin has a nominal diameter of 18.94 mm with a stated dimensional tolerance of ±0.002 mm, suitable for precise end‑measure verification. Is this pin suitable for repeated insertion into press fits? Yes, the pin is made from special steel and the workshop design is intended for robust, repetitive use in insertion and end‑measure checks. How is the item identified for stock and ordering? This single gauge pin is listed under SKU M323.I94 and can be ordered through Metav IndustryLine channels. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
18.95mm Gauge Pin, Single, 50mm Length, Workshop Version - Metav IndustryLine
Take advantage of the combination of tight tolerance (±0.002 mm), special-steel construction and compact dimensions for dependable end-measurement checks. Order the gauge pin directly via Metav Werkzeuge or consult the specialists for application advice. Gauge pin, single, 18.95 mm diameter, 50 mm length — Metav IndustryLine precision gauge pin The gauge pin, single 18.95 mm diameter and 50 mm length, serves as a hardened reference element for end-measure verification and fixture checks in workshop and inspection environments. Workshop version for robust shop use Diameter 18.95 mm and length 50 mm Tolerance ±0.002 mm for tight checks Made from special steel Precision that stabilises quality control A compact hardened measuring pin designed for repeatable end-measure checks brings measurable improvements to inspection routines. With a declared tolerance of ±0.002 mm, the pin provides a narrow acceptance band that reduces ambiguity during go/no-go assessments and minimises rework. The specified accuracy supports consistent gauging in assembly and toolmaking workflows, where small deviations lead to fitment issues. By converting a physical dimension into a reliable reference, this component shortens decision times on the shop floor and stabilises process capability. Robust design engineered for everyday workshop use Built as a workshop version, the pin combines practical dimensions with a sturdy material choice: special steel that resists everyday handling and the occasional impact typical in production environments. The compact 50 mm length and 18.95 mm diameter are sized for end-stop and plug applications without compromising handling convenience. Supplied in a protective transport case, the item reaches the bench ready for use and protected during storage or transit. The construction emphasises straightness and surface finish to ensure repeatable contact points and long service life under normal workshop conditions. Practical integration and traceability for inspection tasks The pin is suited to plug and end-measure tests, fixture set-up, and dimensional references where a fixed diameter is required. Marking and traceability are supported by clear item identification (SKU M323.I95, GTIN 4061905071768), simplifying inventory and inspection records. The combination of compact geometry and defined tolerance makes the component suitable as a reference element in jigs, checking fixtures and assembly aids, where a reliable, repeatable contact surface accelerates alignment and reduces measurement scatter in routine checks. For tailored advice or to order this Metav IndustryLine gauge pin directly from Metav Werkzeuge in Emmerich — call +49 2822 7131930 or email info@metav-werkzeuge.com for prompt, expert support. Technical data SKU: M323.I95 GTIN: 4061905071768 Article: Gauge pin, single, 18.95 mm × 50 mm Facts Diameter: 18.95 mm Length: 50 mm Tolerance: ±0.002 mm Weight: 0.15 kg Special features Material: Special steel Workshop version Supplied in protective transport case Category: Gauge pins FAQ What are the exact dimensions of the pin? The gauge pin has a diameter of 18.95 mm and a length of 50 mm as specified for end-measure applications. Which tolerance class applies to this measuring element? The measuring element is specified with a tolerance of ±0.002 mm, suitable for tight go/no-go and reference checks. Is the pin suitable for use in fixture set-ups and jigs? Yes, the gauge pin is intended for fixture set-up, end-measure verification and as a hardened reference in jigs and checking fixtures. What material is the pin made from and how does that affect use? The pin is manufactured from special steel, providing robustness for workshop handling and a stable contact surface for repeatable measurements. How can the product be identified and tracked in inventory? Identification is possible via SKU M323.I95 and GTIN 4061905071768, which facilitate inventory control and documentation in quality records. Metav IndustryLine: Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
18.96mm Gauge Pin 50mm Length Workshop Version, Special Steel - Metav IndustryLine
Take advantage of the combination of high repeatability, tight tolerance and robust workshop design for reliable end‑measurement control. The Ø 18.96 mm diameter and 50 mm overall length provide a compact reference that integrates easily into inspection benches and gauge assemblies. Order the test pin directly via Metav Werkzeuge or ask our consultants if needed. Test pin M323.I96 (Ø 18.96 mm, 50 mm length) – Metav IndustryLine Test pin M323.I96 is a precision inspection pin intended for end‑measurement and reference applications in workshop metrology and inspection fixtures. Precision tolerance ±0.002 mm Diameter Ø 18.96 mm Length 50 mm Special steel construction Workshop execution Consistent dimensional control for production workflows A compact reference element for dimensional checks, the test pin guarantees consistent repeatability when used in comparative or go/no‑go fixtures. The specified tolerance of ±0.002 mm supports fine control over manufacturing deviations and aids quick decision making on the shop floor. As a single, purpose‑built pin, it is suitable for incorporation into manual gauges, transfer stages and fixture locators where a stable datum and minimal variation are essential. Design that supports fast inspection cycles The combination of Ø 18.96 mm nominal diameter and 50 mm length yields an element that is rigid enough for short‑span reference tasks yet compact for tight assemblies. The workshop execution denotes a practical balance between precision and handling: the profile resists minor knocks and can be handled without complex clamping, reducing time per check and raising throughput. Where short cycle times and repeatable outcomes matter, this configuration reduces fixture rework and measurement drift. Material choice and traceability for long‑term use Manufactured from special steel, the pin offers wear resistance suitable for repeated contact in inspection routines and maintains dimensional stability under normal workshop conditions. Traceability is supported by the listed identifiers (GTIN 4061905071775, SKU M323.I96), which simplify inventory and quality records. When integrated into a controlled inspection process, the pin becomes a reliable reference that contributes to consistent component quality across production batches. Contact Metav Werkzeuge for availability of the Metav IndustryLine test pin and to discuss supply or specification requirements for workshop inspection systems Technical data SKU: M323.I96 GTIN: 4061905071775 Brand: Metav IndustryLine Weight: 0.15 kg Facts Diameter: 18.96 mm Length: 50 mm Tolerance: ±0.002 mm Special features Material: Special steel Configuration: Single test pin Intended use: Workshop inspection and reference gauging FAQ What tolerance can be expected from this test pin? The test pin M323.I96 is specified with a tolerance of ±0.002 mm, making it suitable for fine inspection tasks and tight comparative gauges. Which environments is the pin designed for? Produced in a workshop execution and made from special steel, the pin is intended for regular shop‑floor use in inspection benches and fixture assemblies. Can this pin be used as a reference in gauge fixtures? Yes, the M323.I96 is designed for incorporation into gauge fixtures and transfer jigs where a stable end‑measurement datum is required. How is the component identified for traceability? Identification is facilitated by the GTIN 4061905071775 and SKU M323.I96, supporting inventory control and quality documentation. Metav IndustryLine: Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
18.97mm Gauge Pin 50mm Length Workshop Version, Special Steel - Metav IndustryLine
Take advantage of a workshop-grade inspection pin that combines high repeatability, a nominal diameter of 18.97 mm and a tight tolerance of ±0.002 mm to speed up acceptance checks and reduce rework. The compact 50 mm length and robust special-steel construction make this pin a reliable element for go/no-go fixtures or length gauges; order directly via Metav Werkzeuge or consult their specialists for application advice. Test pin, single, diameter 18.97 mm, length 50 mm — Metav IndustryLine A Test pin, single, diameter 18.97 mm, length 50 mm designed as a workshop-grade inspection component for repeatable dimensional checks and fixture use. Workshop-grade execution for robust use Diameter 18.97 mm with ±0.002 mm tolerance 50 mm length for stable seating Made from special steel for long service life Precision that reduces inspection time The inspection pin is engineered to deliver consistent measurement results with a specified tolerance of ±0.002 mm, which directly improves pass/fail decisions in production control. A nominal diameter of 18.97 mm and tightly controlled manufacturing variability mean fewer uncertain measurements and a reduced need for secondary checks; this increases throughput in repetitive inspection tasks and minimises stoppages caused by ambiguous results. The benefit is quantifiable: reduced cycle time for gauge checks and a sharper statistical basis for quality decisions. Built to withstand workshop conditions Designed as a workshop-grade item, the component uses special steel to combine wear resistance with stability under repeated use. The 50 mm effective length provides a stable seating depth in fixtures and reduces bending moments during manual handling, so measurements remain more reproducible over time. The single-piece design simplifies insertion into existing gauge holders or bespoke fixtures; the result is durable performance with low maintenance effort, supporting continuous inspection routines in machine shops and toolrooms. Traceability and integration into inspection routines Supplied as a single item and identified by article number M323.I97, the pin integrates easily into established gauge sets and inspection protocols. The compact format is particularly useful where space is limited but dimensional certainty is essential, for example in final inspection jigs or comparative master checks. With clear numerical specifications and a robust material choice, the component supports consistent documentation and audit trails in quality systems, making it straightforward to reference in inspection reports and measurement logs. For assistance with selecting the right Metav IndustryLine inspection components or to check availability of item M323.I97, please contact Metav Werkzeuge in Emmerich via info@metav-werkzeuge.com or by phone on +49 2822 7131930 Technical data Article number: M323.I97 GTIN: 4061905071782 Label: Test pin, single, diameter 18.97 mm, length 50 mm Material: Special steel Feature: Workshop-grade Facts Length: 50 mm Nominal diameter: 18.97 mm Tolerance: ±0.002 mm Weight: 0.15 kg Special features Single inspection pin Robust workshop execution Suitable for go/no-go and seating checks Identified by M323.I97 FAQ What is the nominal diameter and tolerance of this inspection pin? The inspection pin has a nominal diameter of 18.97 mm with a specified tolerance of ±0.002 mm for repeatable dimensional inspection. What is the overall length of the component? The component has an overall length of 50 mm and is intended for stable seating in fixtures and gauge holders. Which material is used for the pin? The pin is made from special steel, specified for wear resistance and durability in workshop environments. Is the item supplied individually or in sets? The product is supplied as a single inspection pin under article number M323.I97. For which inspection tasks is this pin most suitable? The pin is suitable for go/no-go checks, seating and length verification in workshop fixtures and gauge assemblies where a compact, precise master is required. Metav IndustryLine: Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
18.98mm Gauge Pin 50mm Length Workshop Version - Metav IndustryLine
Take advantage of the precise fit and robust workshop design: the combination of ±0.002 mm tolerance, special steel construction and compact 50 mm length ensures reliable end‑dimension checks and repeatable inspection results. Order directly via Metav Werkzeuge or consult the advisers for specification support. Gauge pin M323.I98 — 18.98 mm diameter, 50 mm length (Metav IndustryLine) The gauge pin M323.I98 is a single test pin for precision end‑measure and fit control in workshop inspection and assembly environments. Workshop version construction Tolerance ±0.002 mm Diameter 18.98 mm Supplied in transport case Precision fit where tolerance determines quality For tasks that demand consistent fits and tight clearances, the gauge pin delivers measurable certainty. Manufactured to a nominal diameter of 18.98 mm with a stated tolerance of ±0.002 mm, this test pin is suited to go/no‑go checks, plug gauges and reference fits where small deviations matter. The fine tolerance reduces rework and helps maintain process capability when used in inspection benches or simple comparative gauges. The compact geometry and single‑piece supply make it straightforward to integrate into established measuring routines without additional fixtures. Robust workshop design for frequent handling Constructed from special steel, the pin is engineered for repeated contact in production and maintenance settings. The 50 mm overall length gives a secure grip and stable engagement in assemblies while keeping handling ergonomic during repeated use. As a workshop version, the finish and hardness balance wear resistance with practical serviceability, so everyday inspection cycles remain efficient. Supplied in a transport case, the item is protected in transit and ready for storage in a tool kit or inspection drawer, supporting straightforward inventory management. Easy integration into metrology workflows Classified in the micro range for small‑format gauges, the test pin is appropriate for precision end‑dimension controls in component inspection, jigs and gauges. Traceable ordering is supported by the SKU and GTIN identifiers, simplifying procurement and stock keeping. For layout and fixture design, the consistent diameter and minimal runout improve repeatability when used as a reference mandrel or positional locator. Technical advisors at Metav Werkzeuge can provide application guidance and confirm fitment in specific inspection setups, ensuring the part complements existing calibration and quality procedures. Request a quotation or technical advice for the Metav IndustryLine gauge pin from Metav Werkzeuge in Emmerich — call +49 2822 7131930 or email info@metav-werkzeuge.com for application support and assured supply Technical Data Article number: M323.I98 GTIN: 4061905071799 Weight: 0.15 kg Material: Special steel Overall length: 50 mm Facts Diameter: 18.98 mm Tolerance: ±0.002 mm Length: 50 mm Weight: 0.15 kg Special features Workshop version Supplied in transport case for secure transport Single piece supply SKU: M323.I98 FAQ What tolerance does this gauge pin offer? The gauge pin is manufactured to a diameter of 18.98 mm with a tolerance of ±0.002 mm, suitable for tight fit and end‑dimension checks. Is the pin suitable for routine workshop inspection? Yes, the workshop version and special steel construction make the pin well suited for frequent handling and everyday inspection tasks. Can this test pin be used as a reference in jigs and fixtures? The consistent diameter and tight tolerance allow the pin to serve as a reliable reference mandrel or locator in lightweight fixtures and gauges. How is the item supplied for transport and storage? The pin is supplied in a protective transport case to safeguard the measuring surface during transit and storage. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
18.99mm Gauge Pin, Single, 50mm Length, Workshop Version - Metav IndustryLine
Take advantage of the combination of precise diameter control, a compact 50 mm body and workshop-grade construction for reliable end‑dimension verification; order the gauge pin directly via Metav Werkzeuge or consult our specialists for application advice. Gauge Pin M323.I99 — Single precision test pin, 18.99 mm diameter, 50 mm length (Metav IndustryLine) The Gauge Pin M323.I99 is a single precision test pin intended for end‑dimension checks and fixture verification in industrial metrology and workshop inspection. Precision tolerance ±0.002 mm Diameter 18.99 mm, length 50 mm Made from special steel Delivered in protective transport case Precision for consistent end‑dimension verification The compact test pin delivers high precision with a stated tolerance of ±0.002 mm, making it suitable for fine inspection tasks where repeatability is essential. With a nominal diameter of 18.99 mm and a length of 50 mm, the pin serves as a reliable reference for plug‑type checks and final dimensional control. The tight tolerance reduces uncertainty during accept/reject assessments and supports consistent quality documentation in production and incoming inspection workflows. Robust construction tuned to workshop demands Designed as a workshop version, the test pin is manufactured from special steel chosen for dimensional stability and handling resilience. The solid construction and a compact mass (approx. 0.15 kg) make the component easy to seat in fixtures and gage blocks without compromising rigidity. Supplied in a protective transport case, the pin is ready for safe storage and movement between bench, machine or inspection station, preserving the reference surface and minimising reconditioning downtime. Practical integration for inspection and fixture use As a purpose‑built gauge pin, the component integrates easily into existing inspection setups and assembly jigs, offering a simple physical standard for end‑dimension and plug‑fit tests. The single‑piece design supports quick swap‑in checks and is suitable as a reference for comparative measurements on bench comparators or manual gauges. Traceability and stock management are simplified by the clear SKU and GTIN information, so the pin can be referenced precisely in inspection plans and parts lists. For targeted end‑dimension verification with the reliability of Metav IndustryLine, request the M323.I99 through Metav Werkzeuge or contact our consultants at info@metav-werkzeuge.com or +49 2822 7131930 for tailored advice. Technical data Article number: M323.I99 GTIN: 4061905072130 Brand: Metav IndustryLine Dimensions & weight Nominal diameter: 18.99 mm Length: 50 mm Weight: 0.15 kg Tolerance / accuracy: ±0.002 mm Materials & features Material: special steel Version: workshop execution Category: gauge pin / test pin Packaging: protective transport case FAQ What is the primary application of this gauge pin? The M323.I99 gauge pin is intended for end‑dimension checks and fixture verification in metrology and workshop inspection tasks. What tolerance does the test pin achieve? The M323.I99 is specified with a tolerance of ±0.002 mm, suitable for high‑precision comparative checks. From which material is the pin manufactured? The test pin is made from special steel in a workshop‑grade execution to balance durability and dimensional stability. Is the pin supplied ready for transport and storage? Yes, the pin is delivered in a protective transport case to preserve the reference surfaces during handling and transit. How can the pin be integrated into existing inspection workflows? The single‑piece gauge pin functions as a straightforward reference for plug‑type checks, compatible with manual gauges, fixtures and bench inspection routines; reference M323.I99 and the GTIN for documentation. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
18.9mm Gauge Pin 50mm Length Workshop Version - Metav IndustryLine
Compact, workshop-grade test pin combining Ø 18.9 mm diameter and a special‑steel construction with a manufacturing tolerance of ±0.002 mm for dependable end‑measure inspections; order the M323.I90 directly via Metav Werkzeuge or consult our specialists for application advice. Test pin, single, Ø 18.9 mm, 50 mm length — Workshop version (Metav IndustryLine) A Test pin, single, Ø 18.9 mm, 50 mm length designed for precise end‑measure checks and reference inspections in workshop and production inspection stations. Workshop version, rugged design Precision tolerance ±0.002 mm Diameter Ø 18.9 mm for end‑measure checks Compact 50 mm length for stable seating High precision where it counts The M323.I90 is manufactured to a tight tolerance of ±0.002 mm, providing a measurable advantage when repeatability and traceable reference dimensions are required. The controlled diameter helps to reduce measurement scatter during comparative checks and reference seating operations, turning raw measurements into actionable results. By relying on a consistent diameter and verified manufacturing tolerance, inspection throughput improves because adjustments and rechecks are reduced, supporting a more efficient quality workflow. Built for workshop reliability and handling Constructed from special steel and executed as a workshop version, this single test pin is tailored for frequent handling and routine inspection tasks. The 50 mm length delivers a compact contact surface that seats securely in fixtures and gauges, while the modest weight of 0.15 kg contributes to convenient manual placement without compromising stability. These attributes reduce downtime for replacements and simplify integration into handheld gauges or fixture assemblies, extending the service life of measurement set‑ups in demanding production environments. Practical uses and inspection benefits Designed primarily for end‑measure inspection and reference gauging, the test pin is well suited to assembly checks, go/no‑go verification and dimensional referencing of mating components. Its workshop specification supports repetitive use on benches and in quick‑change test stations, where the consistent diameter and robust material translate into reliable contact behaviour. Specifying a component such as this one can streamline routine inspections and offer a straightforward means to maintain traceable reference points across production batches. Contact Metav Werkzeuge for availability and expert guidance on the M323.I90 test pin and its integration into existing inspection procedures Technical Data Article number: M323.I90 GTIN: 4061905071201 SKU: M323.I90 Name: Test pin, single, Ø 18.9 mm, length 50 mm Brand: Metav IndustryLine Facts Diameter (mm): 18.9 Length (mm): 50 Weight (kg): 0.15 Manufacturing tolerance (mm): ±0.002 Material: Special steel Special features Workshop version Single test pin delivery Application: end‑measure inspection and reference checks Category: Test pins FAQ What is the dimensional tolerance of the test pin? The M323.I90 test pin is produced to a manufacturing tolerance of ±0.002 mm, ensuring consistent reference dimensions for inspection tasks. Which material is used for this test pin? This item is made from special steel, specified to provide robust contact surfaces and resistance to wear in workshop conditions. For which inspection tasks is this pin suitable? Typical uses include end‑measure checks, go/no‑go verifications and reference seating in fixtures; the design supports frequent handling and repeat measurements. How does the 50 mm length affect handling and seating? A 50 mm length offers compact, stable seating in fixtures and gauges, aiding secure contact and reducing the risk of misalignment during manual checks. Is the M323.I90 appropriate for production benches and manual gauges? Yes; the workshop version and durable material make the M323.I90 suitable for use on production benches, handheld gauges and short‑cycle inspection stations. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
180mm Setting Ring Form C Hardened Gauge Steel DIN 2250, DIN 286 JS 3 - Metav IndustryLine
Benefit from hardened, lapped gauge steel, a precise JS 3 tolerance and a stable 180 mm diameter for reliable bore setting and calibration; order the setting ring directly via Metav Werkzeuge or consult our advisers for specification support. Setting ring 180 mm (M313.180) – Ring gauge, Hardened & Lapped, DIN 2250 The Setting ring 180 mm (M313.180) is a DIN 2250‑compliant ring gauge for production and quality control, intended to verify and set internal diameters in machining and inspection tasks. Form C ring gauge, DIN 2250 compliant Hardened and lapped gauge steel JS 3 tolerance class for precise setting Consistent tolerance and measurable benefit for production The ring gauge is manufactured to DIN 2250 and DIN 286, delivered in JS 3 tolerance, which translates into repeatable dimensional control on the shop floor. This conformity ensures that the gauge serves as a reliable reference when setting bore sizes or checking internal diameters; using a class‑marked ring gauge reduces setup time and rework by providing a certified limit for go/no‑go decisions. The hardened and lapped surface minimises wear and maintains gaugeability over repeated cycles, supporting shorter process windows and higher first‑pass yields. Robust construction that supports repeatable handling Constructed from hardened, lapped gauge steel, the device combines surface hardness with fine finishing to resist deformation and abrasion during routine use. The Form C geometry is optimised for stable seat and alignment in typical bore fixtures, contributing to consistent measurement contact and minimised eccentricity. At 180 mm diameter and approximately 7 kg mass, the ring gauge offers a balance between rigidity and manageable handling for bench or fixture use, ensuring measurements remain reproducible across operators and shifts. Practical integration into inspection and setting workflows Designed for direct use in both manufacturing and inspection environments, this ring gauge simplifies calibration of internal measuring instruments and the setup of machining centres. As a traceable reference, it supports process control plans and helps maintain compliance in serial production. The JS 3 class and DIN designation facilitate clear specification in technical drawings and procurement documents, allowing the gauge to be used as a contractual measurement standard within quality systems. Contact Metav Werkzeuge for specification advice and to order the Metav IndustryLine 180 mm setting ring (M313.180), including options for calibration certificates and delivery from our Emmerich quality hub. Technical data SKU: M313.180 GTIN: 4054469121222 ECLASS: 21170104 Norm: DIN 2250; DIN 286, JS 3 Material: hardened and lapped gauge steel Special form: Form C Facts Diameter: 180 mm Weight: 7 kg Tariff number: 90173000 Special features Hardened and lapped surface finish Form C geometry for stable seating Suitable as a setting ring and reference gauge Intended for production and quality control applications Category: gauges (ring gauge) FAQ What is the intended use for this ring gauge? The setting ring 180 mm (M313.180) is intended as a reference gauge for verifying and setting internal diameters, used in production and inspection to ensure conformity with specified bore sizes. Which standards and tolerance class apply to this gauge? This ring gauge is manufactured to DIN 2250 and DIN 286 standards and is supplied in JS 3 tolerance class for precise setting and verification tasks. What material and finish does the gauge have? The gauge is made from hardened and lapped gauge steel, which provides wear resistance and a fine surface finish for reproducible contact conditions. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
185mm Setting Ring Form C, Hardened Gauge Steel, DIN 2250 / DIN 286 JS 3 - Metav IndustryLine
Combine DIN 2250 conformity with a hardened, lapped gauge steel finish and a precise JS 3 tolerance to secure repeatable setups and minimise adjustment time on production lines. Order the setting ring directly via Metav Werkzeuge or consult our specialists for specification matching and delivery. Setting ring M313.185 – 185 mm hardened gauge steel, DIN 2250 (Metav IndustryLine) The Setting ring M313.185 is a precision ring gauge designed for setting, inspection and calibration tasks in toolmaking and metrology, providing a stable reference for internal-diameter checks and instrument adjustment. Hardened, lapped gauge steel DIN 2250 / DIN 286, JS 3 tolerance Form C contour for versatile fits Nominal diameter 185 mm Consistent accuracy for fast, repeatable setups The ring serves as a stable reference that reduces adjustment cycles and supports faster throughput on the shop floor. Manufactured from hardened gauge steel with a lapped finish, this component maintains dimensional integrity over time and resists wear that would otherwise affect fits. Conformity with DIN 2250 and DIN 286 and the JS 3 tolerance class means the ring can be used as a verified standard for comparison measurements and instrument setting, giving measurable benefits in reproducibility and process control. Robust construction to withstand industrial use A Form C profile and the solid construction ensure secure seating in fixtures and consistency during repeated use. The substantial mass contributes to stability during inspection and helps prevent movement that would introduce measurement scatter. The lapped surface minimises friction and contact wear, lowering maintenance needs and extending service intervals in daily operation. These attributes make the ring suitable for routine setting tasks in machining, assembly and quality-control environments. Practical application: where the ring excels in production Use the ring gauge as a master for setting internal measuring instruments, aligning bore gauges, checking mandrels and validating plug gauges. Its 185 mm nominal diameter and precise finish simplify pass/fail comparisons and reduce setup-related scrap by improving first-time conformity. The ring’s geometry also aids in repeatable placement in jigs and fixtures, so inspection steps become faster and less dependent on operator technique, yielding immediate productivity gains for workshops and small-series production. Contact Metav Werkzeuge for tailored advice on integrating the Metav IndustryLine setting ring M313.185 into inspection routines and to arrange supply from our Emmerich quality hub Technical data Article number: M313.185 GTIN: 4054469121239 Material: gauge steel, hardened and lapped Special feature: Form C Facts Diameter: 185 mm Weight: 8.25 kg Tariff number: 90173000 eClass: 21170104 Special features Standards: DIN 2250; DIN 286; JS 3 Application: setting and inspection in metrology and toolmaking Finish: lapped surface FAQ What does the JS 3 tolerance mean for a ring gauge? The JS 3 class specifies the permissible deviation band for the nominal diameter; the Setting ring M313.185 meets this class under DIN requirements, enabling consistent repeatability for comparative measurements. Which material and finish are used on this ring? The ring is made of hardened gauge steel and delivered with a lapped surface to reduce wear and maintain accuracy over prolonged use. For which tasks is this ring most suitable? The component is intended for instrument setting, internal-diameter references, bore-gauge alignment and pass/fail checks in toolmaking and inspection workflows. Can this ring be used in a production workshop rather than a metrology lab? Yes; the robust construction, lapped finish and Form C profile make the unit well suited to industrial workshop environments where durability and repeatability are required. How should the ring be handled and stored to preserve accuracy? Handle the ring carefully to avoid impacts; store in a clean, dry environment and protect the lapped surface from abrasives and corrosive agents to preserve measurement integrity. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
187.5mm Setting Ring Form C, Hardened Gauge Steel, DIN 2250/DIN 286 JS3 - Metav IndustryLine
Take advantage of the combination of standardised tolerances, robust hardened and lapped gauge steel, and a machine‑friendly 187.5 mm diameter for reliable setting and inspection tasks; order the setting ring directly via Metav Werkzeuge or ask our consultants if needed. Setting ring 187.5 mm (DIN 2250) — Hardened, lapped gauge steel by Metav IndustryLine The Setting ring 187.5 mm is a precision ring gauge for diametral verification and setting tasks in quality control, toolrooms and production inspection. DIN 2250 / DIN 286, tolerance JS3 Hardened and lapped gauge steel Diameter 187.5 mm for precise setting Form C design for standardised checks Consistent tolerances for reproducible measurement setup Manufactured to DIN 2250 and DIN 286 with tolerance class JS 3, this ring offers a defined reference diameter that reduces setup variability when calibrating gauges or aligning fixtures. The standardised tolerance ensures that the ring functions as a reliable master for comparative checks and setting operations on production machinery. By providing a stable reference, process uptime and first‑pass yield are supported through quicker, more predictable setup routines. Wear resistance and stable handling on the workshop floor Produced from gauge steel, hardened and lapped, the ring resists abrasion and preserves its metrological surface under repeated contact. The lapped finish minimises surface roughness and promotes repeatable seating of mating parts, while the mass of 7.55 kg contributes to a vibration‑damping effect during bench use. The Form C geometry simplifies clamping and standardised placement, which helps maintain measurement integrity across shifts and operators. Practical integration into inspection workflows Supplied as a durable, shop‑ready reference, the ring gauge streamlines gauge setting and Go/No‑Go checks in small and medium series production. Traceability is supported by clear identification (SKU M313.187.5) and industry classification for inventory management. The compact, single‑diameter design suits bench clamping and fixture use while saving time compared with iterative measurement methods, facilitating faster control loops and consistent quality documentation. Contact Metav Werkzeuge for a tailored supply from Emmerich — our consultants provide specification advice and delivery guidance by eMail at info@metav-werkzeuge.com or by phone on +49 2822 7131930 Technical Data Article number: M313.187.5 Label: Setting ring 187.5 mm, DIN 2250, hardened gauge steel GTIN: 4054469121246 Facts Diameter: 187.5 mm Weight: 7.55 kg Customs tariff number: 90173000 ECLASS: 21170104 Special features Material: gauge steel, hardened and lapped Standards: DIN 2250; DIN 286 Tolerance class: JS 3 Form: Form C Category: Gauges / Setting rings FAQ What is the primary use of this setting ring? The setting ring is intended as a reference diameter for gauge setting, comparative checks and fixture alignment; the ring identified as M313.187.5 fulfils this role in inspection and workshop environments. How does the tolerance class JS 3 affect its application? Tolerance class JS 3 indicates a tightly controlled tolerance band under DIN 2250, making the ring suitable where repeatable, standardised settings and classification against production limits are required. Is the surface treatment suitable for frequent use? Yes. The ring’s hardened and lapped finish provides a wear‑resistant, low‑friction contact surface that maintains dimensional stability under repeated seating and inspection cycles. Can this ring be used in a production line for quick Go/No‑Go checks? The ring’s single, precise diameter and Form C design make it well suited to quick verification and Go/No‑Go procedures on the bench or in simple fixture arrangements. Does the product come with identification for inventory and traceability? The ring is supplied with clear identification (SKU M313.187.5) and GTIN for inventory control and traceability within quality systems. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
18mm Limit Plug Gauge Wear Allowance, Hardened Steel, DIN 7162 - Filetta
Taking advantage of a hardened-steel construction and conformity to DIN 7162, this limit plug gauge delivers reliable go/no-go inspection with an integrated wear allowance on the go side; order the Filetta gauge via Metav Werkzeuge or contact our consultants for supply and technical advice. Limit plug gauge MS911.222 by Filetta — hardened steel, DIN 7162 compliant The Limit plug gauge MS911.222 is a precision cylindrical gauge designed for rapid verification of internal diameters to DIN 7162, primarily intended for production control and incoming‑goods inspection Hardened steel construction to DIN 7162 18 mm nominal diameter gauge Wear allowance on the go side Precision gauge for internal diameter checks Consistent conformity through standardised construction The gauge is manufactured in hardened steel, offering dimensional stability and resistance to surface wear for repetitive checks. Built to DIN 7162, the design ensures compatibility with recognised inspection workflows and reduces ambiguity in acceptance criteria. Using a standardised limit plug means that measurement decisions are reproducible between operators and shifts, which helps to lower scrap rates and supports traceable quality routines across production lines. Practical benefit of the wear allowance and go/no‑go function A defined wear allowance on the go side prolongs useful life while maintaining effective pass criteria during routine use. The simple go/no‑go concept embedded in the geometry translates technical tolerance into an immediate decision—acceptable or not—so inspection cycles are faster and less error‑prone than subjective gauging. This functional clarity improves throughput in assembly and inspection stations and makes the gauge particularly suitable for high-volume checks where speed and reliability matter. Integration into inspection routines and fixtures Compact and robust, the instrument is straightforward to fit into gauge stands, inspection benches or assembly jigs for repetitive testing. The nominal diameter of 18 mm is clearly indicated for process documentation and facilitates inventorying of gauge sets. For workshop and production environments where quick verification and clear go/no‑go outcomes are required, this type of limit plug gauge supports consistent part acceptance and contributes to smoother downstream assembly operations. For a reliable supply of Filetta limit plug gauges and tailored advice for inspection setups, contact Metav Werkzeuge in Emmerich by e‑mail at info@metav-werkzeuge.com or by phone on +49 2822 7131930 — our consultants will assist with availability and order details Technical data Article number: MS911.222 Name: Limit plug gauge (Grenzlehrdorne) Manufacturer: Filetta Standard: DIN 7162 Measurements Nominal diameter: 18 mm Materials & features Material: hardened steel Feature: wear allowance on the go side FAQ What is the primary use of this gauge? The Filetta limit plug gauge MS911.222 is used for go/no‑go verification of internal cylindrical bores with a nominal diameter of 18 mm, enabling fast acceptance decisions in production inspection. Which standard does the instrument comply with? Manufactured to DIN 7162, the gauge follows established geometry and tolerance rules for limit plug gauges to ensure comparable inspection outcomes. How does the wear allowance affect service life? The wear allowance on the go side extends the gauge’s operational life by permitting controlled material loss before the no‑go limit is reached, maintaining reliable pass criteria for longer. Is the gauge suitable for fixture integration? Yes, the compact, hardened‑steel design of this limit plug gauge is suitable for mounting in gauge stands, inspection benches and jigs for repetitive testing. Manufacturer / Responsible: Schut Geometrische Meettechniek bv; Duinkerkenstraat 21; 9723 BN Groningen; The Netherlands; +31 50 5877877; schutnl@schut.com
18–19mm Go/No-Go Gauge Pin Set 0.01mm Steps With Pin Holder In Plastic Case - Metav IndustryLine
Benefit from a combination of high metrological reliability, fine 0.01 mm graduations and robust special‑steel construction for consistent inspection results; order the gauge pin set directly via Metav Werkzeuge or ask our consultants if needed. Gauge pin set M318.588 — 101-piece, 18.00–19.00 mm, 0.01 mm increments (Metav IndustryLine) The Gauge pin set, 18–19 mm, 0.01 mm increments is a precision inspection kit for gap, hole and fixture verification in industrial metrology and quality control 0.01 mm graduation for fine steps Nominal accuracy ±0.004 mm Made from special steel Includes pin holder for secure handling 101‑piece set for continuous coverage Precision that reduces rework and speeds inspections The gauge pin set delivers measured, reproducible checks across a narrow, high‑resolution band. With 0.01 mm increments and a nominal accuracy of ±0.004 mm, the pins support fast go/no‑go assessments and incremental verification routines that lower the risk of assembly faults. Using discrete, calibrated pin sizes simplifies pass/fail decisions on jigs and bore alignments, which translates into shorter inspection cycles and fewer process stoppages. Workshop ergonomics and practical handling Designed for repetitive use in production and metrology benches, the kit combines compact organisation with operational convenience. The included pin holder ensures safe, repeatable handling during insertion and withdrawal, while the 101‑piece range covers every step between 18.00 and 19.00 mm to avoid makeshift workarounds. Durable surfaces and consistent diameters maintain performance over many cycles, giving technicians confidence during setup and sampling tasks. Material choice and application guidance Constructed from special steel, each pin emphasises wear resistance and dimensional stability under normal workshop conditions. The set is well suited to calibration, gauge setting and bore checking in general metalworking environments. The individual diameters are ideal for finishing checks, alignment tasks and fixture validation; the incremental design removes ambiguity when matching pins to tolerance stacks. The product designation M318.588 identifies this specific Metav IndustryLine kit for procurement and documentation purposes. For specification advice or to reserve the Metav IndustryLine gauge pin set, contact Metav Werkzeuge in Emmerich — our consultants will recommend the right configuration for inspection routines and delivery timing Technical Data SKU: M318.588 GTIN: 4054469156255 Brand: Metav IndustryLine Material: Special steel Measurement range: 18.0–19.0 mm Graduation: 0.01 mm Pieces per set: 101 Nominal accuracy: 0.004 mm Weight: 14 kg Length (typical pin): 50 mm Tariff number: 90173000 Facts Measurement range min: 18 mm Measurement range max: 19 mm Graduation step: 0.01 mm Accuracy: 0.004 mm Number of pieces: 101 Weight: 14 kg Pin length: 50 mm Special features Includes pin holder for handling Set for fine incremental checking Special steel construction for wear resistance Designed for industrial metrology and gauge tasks Complete 18.00–19.00 mm coverage in 0.01 mm steps FAQ What accuracy can be expected from this gauge pin set? The Metav IndustryLine gauge pin set M318.588 is specified with a nominal accuracy of 0.004 mm, suitable for precise workshop and inspection tasks. Which measurement range is covered by the set? The kit spans the 18.00–19.00 mm band in 0.01 mm steps, providing continuous coverage for incremental bore and gap checks. What material are the pins made from and why does that matter? Pins are made from special steel to ensure dimensional stability and wear resistance, which preserves measurement integrity under repeated use. Is a handling aid included with the set? Yes, the package contains a pin holder that improves handling safety and repeatability during insertion and removal. For which applications is this kit intended? The set is intended for calibration work, fixture and bore checking, assembly verification and other industrial metrology tasks where fine incremental sizes are required. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
19 mm Gauge Ball Pair, Hardened Chrome Steel, Accuracy 0.003 mm, Diameter Tolerance 0.00008 mm - Metav IndustryLine
Take advantage of the combination of hardened chrome steel, matched reference geometry and 3 µm accuracy for reliable inspection and repeatable gauging; order the set directly via Metav Werkzeuge or contact our technical consultants for application advice. Gauge ball pair M318.429 — 19 mm, 0.003 mm accuracy (Metav IndustryLine) The gauge ball pair provides precision reference spheres for calibration, instrument setup and comparative measurement in inspection and workshop environments. Hardened chrome steel construction Precision diameter 19 mm for reference use Dimensional accuracy 0.003 mm Delivered as a matched pair for comparison Consistent, measurable accuracy for inspection work A reference sphere with a diameter of 19 mm and a stated accuracy of 0.003 mm (3 µm) supplies a clear, quantifiable basis for decisions in quality control. The declared diameter tolerance of 0.00008 mm supports fine comparison tasks where even minute deviations matter; this level of specification is useful when verifying the performance of gauges, testing fixture repeatability or checking machine-centre calibration. By relying on objectively stated numbers rather than subjective judgement, production processes can be validated and traced with confidence. The numerical data therefore directly contributes to fewer reworks and more predictable inspection outcomes. Robust material and geometry for repeatable contact Constructed from hardened chrome steel and specified with hardness >HRC 62, the spheres are designed to withstand repeated contact without rapid wear, maintaining geometry across repeated cycles. A low surface roughness supports stable seating against gauge contacts and minimises measurement scatter; consistency of the contact surface helps to reduce variation introduced by surface irregularities. Supplied as a matched pair, the two spheres are closely matched in diameter and finish, enabling comparative checks and quick functional tests between fixtures or measuring devices. The paired format simplifies in‑house verification workflows where a quick cross‑check is required before a production run. Suitable for workshop inspection and calibration labs These reference spheres fit well into standard workshop and laboratory routines where compact, high-precision artefacts are required for setup and verification. Their modest weight and compact size make them easy to handle while still providing a stable reference for small‑part gauging, fixture alignment and comparator work. The product supports rational decision‑making: measurable specifications, durable construction, and a matched delivery format reduce ambiguity during routine checks. Should additional information be required about compatibility with specific gauge systems or inspection procedures, Metav’s Emmerich‑based specialists provide concise technical support and can supply the matched set ready for immediate use. Contact Metav Werkzeuge for delivery from Emmerich and expert advice on matched reference spheres — phone +49 2822 7131930 or eMail info@metav-werkzeuge.com Technical Data Article number: M318.429 GTIN: 4054469184173 Manufacturer: Metav IndustryLine Dimensions & core specifications Diameter: 19 mm Weight per set: 0.08 kg Accuracy: 0.003 mm Diameter tolerance: 0.00008 Surface roughness: 0.00001 Hardness: >HRC 62 Materials & special features Material: hardened chrome steel Supplied as matched set: 2 pieces per set Suitable application: gauges / inspection reference FAQ What measurement accuracy can be expected from these gauge balls? The gauge ball pair M318.429 from Metav IndustryLine is specified with an accuracy of 0.003 mm, making the set suitable for sub-millimetre reference tasks and fine comparative checks in inspection environments. Are the spheres delivered as a matched set? Yes, the product is supplied as a matched set of two spheres (SKU M318.429), enabling direct comparison and fast functional verification between fixtures or measuring devices. What material and hardness are the reference spheres made of? The spheres are manufactured from hardened chrome steel with a hardness greater than HRC 62, which supports long-term wear resistance and stable contact geometry. Can these gauge balls be used for fixture and gauge checks in a production workshop? The matched pair and the defined tolerance make them well suited for workshop fixture checks, comparator setups and routine instrument verification where compact, durable reference items are required. Who to contact for further technical details or to request supply? For delivery, technical queries or compatibility advice, contact Metav Werkzeuge in Emmerich; their consultants can provide application guidance and handle orders for the M318.429 gauge ball pair. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
Fast, tactile checks where electronics are impractical
Gauges and test pins provide unequivocal go/no-go results for threads, bores, gaps and radii without relying on electronics. The range covers plug gauges and ring gauges for internal and external threads, feeler gauges and precision feeler strips for micro‑gap assessment, plus probe pins and measuring pins for tactile diameter and pitch checks.
How these tools work in the production environment
Mechanical gauges operate as direct reference standards: a plug gauge or ring gauge verifies conformity to thread profiles and mating ability, while limit gauges separate accept from reject in a single step. Test pins are used to tactilely measure small bore diameters, centre‑to‑centre distances and radii. Manufactured from hardened gauge steel or ceramic and often precision lapped, these instruments deliver immediate physical results that are ideal for incoming inspection, machine‑side checks and final control.
Measurable benefits that affect production performance
- Reduced scrap and rework through rapid, unambiguous pass/fail assessment.
- Increased repeatability thanks to very low measurement uncertainty and fine lapping.
- Lower downtime: quick checks at the machine save cycle time and reduce setup periods.
- Durable construction with high wear resistance from specialised, low‑distortion alloys.
- Versatile delivery formats: individual gauges, organised sets in wooden cases or metre‑length feeler rolls compliant with DIN 2269.
Why Metav is the practical choice for precision supplies
Metav combines decades of expertise with a broad warehouse and quality filtering from Emmerich. As a precision partner for industry, craft and trade, Metav supplies a comprehensive selection of gauges and test pins alongside complementary tools such as precision calipers and setting rings. With over 48,000 customers and a catalogue exceeding 250,000 items, Metav is positioned to supply reliably, reduce vendor complexity and support traceable quality control to national standards.
Summary
Gauges and test pins are indispensable for dependable, repeatable quality assurance where tactile, mechanical verification is preferred. Choose these plug gauges, ring gauges, feeler strips and probe pins when immediate, robust measurement decisions are required on the shop floor.
FAQ
What materials are gauges and test pins typically made from?
Gauges and test pins are usually manufactured from hardened gauge steel for durability and wear resistance; ceramic variants are available where thermal stability and minimal wear are critical.
How do thread gauges ensure mating capability?
Thread plug gauges and ring gauges check flank diameters and thread form against standards, providing a clear go/no‑go verdict that confirms pairability with mating parts.
Which tolerance class should I choose for probe pins and gauge sets?
Select tolerance classes aligned with your inspection requirements; for high‑precision tasks, sets produced to DIN 2269 or equivalent tolerance classes ensure micrometre‑level control and repeatability.
Can feeler gauges measure contact gaps in valve and engine work reliably?
Yes. Feeler gauges and precision feeler strips, supplied either as a fan or metre‑length rolls, allow accurate assessment of valve clearances and contact gaps down to micrometre increments.
How do limit gauges speed up in‑process inspection?
Limit gauges separate good from bad in a single, tactile operation, enabling rapid go/no‑go checks at the machine and reducing both inspection time and the likelihood of human interpretation errors.
Fragen zu diesen Produkten??
Mit mehr als 30 Jahren Erfahrung beraten wir Sie gerne persönlich.
Tel.: +49 2822 7131930
Mail: info@metav-werkzeuge.com