Precision gauge blocks and plug gauges for reliable dimensional control
Mechanical gauge blocks and plug gauges are essential for tactile verification of threads, bores and gap dimensions, providing fast, unambiguous go/no-go results that enhance process reliability and reduce scrap. Designed for industrial metalworking and toolmaking, these precision tools support incoming inspection and final quality checks by delivering traceable measurements in applications such as thread inspection, bore diameter testing and spacing checks. Manufactured from specially hardened, low-distortion alloys and fine-lapped for minimal measurement uncertainty, the range includes thread plug gauges, precision plug gauges and calibration gauge blocks to ensure long-term repeatability and wear resistance.
19.23mm Gauge Pin 50mm Length Workshop Version In Plastic Case - Metav IndustryLine
Take advantage of the combination of workshop-grade robustness, tight ±0.002 mm tolerance and compact 50 mm length for reliable end-dimension checks in production and inspection. Order the gauge pin directly via Metav Werkzeuge or consult our specialists for application advice. Gauge pin M323.J23 — single gauge pin, 19.23 mm diameter, 50 mm length (Metav IndustryLine) Gauge pin M323.J23 is a compact verification pin for end-dimension inspection and locating tasks in workshop environments Workshop-grade construction Diameter 19.23 mm precision 50 mm overall length Tolerance ±0.002 mm accuracy Reliable checks with industrial precision The M323.J23 gauge pin delivers repeatable dimensional checks where consistency matters. Manufactured from special steel and finished for accurate seating, the pin’s 19.23 mm diameter and short 50 mm overall length reduce bending and ensure stable contact during measurement. The declared ±0.002 mm tolerance positions the component for fine inspection tasks and close-tolerance fit checks in machining and assembly processes, improving process control and reducing rework. Practical benefits for production and quality control A compact single gauge pin is especially useful for verifying bore sizes, end faces and assembly fits without complex fixturing. The pin’s robustness and ground surface provide a reliable datum for repeat measurements, enabling efficient pass/fail decisions on the shop floor. Integration into existing test fixtures or hand gauges is straightforward thanks to the standardised diameter and short length, supporting faster inspection cycles and a lower rate of false rejects. Built for workshop handling and traceability At 50 mm length and weighing approximately 0.2 kg, this verification pin is easy to handle and store while remaining substantial enough for repeated use. The solid construction supports frequent seating and extraction without rapid wear, preserving measurement confidence over long production runs. Identifiers such as SKU M323.J23 and GTIN 4061905072277 simplify inventory management and traceability in quality documentation. Confidence through expertise and supply chain reliability Sourcing from Metav IndustryLine gives access to a curated selection of measuring hardware underpinned by Metav’s long-standing market presence. The combination of workshop-ready design, tight tolerance and clear identification aids quality departments in maintaining documented conformity and consistent inspection outcomes. Choosing a purpose-made verification pin contributes to stable process capability and dependable product releases. For specification support or to request procurement details for the Metav IndustryLine gauge pin M323.J23, contact Metav Werkzeuge in Emmerich—email info@metav-werkzeuge.com or call +49 2822 7131930 to discuss application fitment and delivery options Technical data Article number: M323.J23 GTIN: 4061905072277 Label: Prüfstift, einzeln, 19,23 mm Länge 50 mm Manufacturer: Metav IndustryLine Core data Diameter: 19.23 mm Length: 50 mm Tolerance: ±0.002 mm Weight: 0.2 kg Special features Workshop version Material: Special steel Application: end-dimension measurement Eclass: 21170231 FAQ What is the primary use of this gauge pin? The gauge pin M323.J23 is intended for end-dimension inspection and locating tasks, providing a stable reference for bore and fit checks in workshop and production settings. How precise is the M323.J23? The M323.J23 is specified with a tolerance of ±0.002 mm, suitable for fine inspection tasks and close-tolerance assemblies. Which material is the pin made from? The pin is produced from special steel, chosen for durability and wear resistance in repeated measurement cycles. Can the M323.J23 be used in standard test fixtures? Yes — the standard diameter and compact 50 mm length facilitate straightforward use in common fixtures and hand-held inspection tools. How is the product identified for inventory and traceability? Identification is via SKU M323.J23 and GTIN 4061905072277, which support stock control and quality documentation. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
19.24mm Gauge Pin, Single, 50mm Length, Workshop Version - Metav IndustryLine
Take advantage of precise diameter control and tight tolerance for repeatable go/no‑go checks; the workshop‑grade construction and protective case ensure secure storage and on‑bench readiness. Order directly via Metav Werkzeuge or consult the specialists for application advice. Gauge pin M323.J24 — workshop test pin, 19.24 mm diameter, 50 mm length (Metav IndustryLine) The gauge pin M323.J24 is a workshop‑grade inspection pin designed for reliable end‑measurements, locating and go/no‑go checks in routine metrology and fixture setups. Workshop‑grade precision Diameter 19.24 mm nominal Tolerance ±0.002 mm 50 mm overall length Delivered in protective case Precision engineered for reliable inspection This inspection pin is manufactured from special steel and finished to a tolerance of ±0.002 mm, providing a measurable step up in repeatability compared with everyday workshop probes. The tight tolerance and defined nominal diameter of 19.24 mm make the component suitable for verifying bore sizes, setting gauges and checking mating parts where small deviations can compromise assembly. Explaining the benefit: tighter tolerance reduces measurement scatter, which in turn lowers rejection rates and rework in production. Practical handling and protected storage With an overall length of 50 mm and a compact, workshop‑oriented design, the pin is easy to handle during manual inspection and fixture use. The delivery in a protective case preserves surface condition and geometry during transport and storage — a practical safeguard that keeps the pin ready for immediate use at the bench. The workshop version construction balances robustness with the fine finish required for accurate contact measurement. Reliable results for everyday metrology tasks For production and maintenance environments the emphasis is on predictable performance. The pin’s combination of material and finish supports consistent contact behaviour and reduces surface wear during repetitive checks. Where inspection frequency is high, this repeatability translates into faster throughput and fewer measurement interruptions, helping teams maintain steady production flow without compromising quality. Application focus and compatibility with inspection workflows Designed as a single inspection element, the pin suits go/no‑go testing, locating operations and as a reference in fixture assemblies. The compact format and defined nominal size facilitate integration with manual gauges and checking fixtures commonly used in machine shops and assembly lines. Metav IndustryLine’s workshop specification ensures the pin meets practical demands while keeping handling straightforward for operators. For workshop applications that demand consistent diameter control and tight repeatability, choose the Metav IndustryLine gauge pin M323.J24 — contact Metav Werkzeuge GmbH at info@metav-werkzeuge.com or +49 2822 7131930 for ordering and tailored advice Technical Data SKU: M323.J24 GTIN: 4061905072284 Brand: Metav IndustryLine Facts Diameter: 19.24 mm Length: 50 mm Tolerance: ±0.002 mm Weight: 0.2 kg Special features Material: Special steel Workshop version Delivered in protective case ECLASS: 21170231 FAQ What nominal size does this inspection pin have? The gauge pin M323.J24 from Metav IndustryLine has a nominal diameter of 19.24 mm, specified for precise fit and verification work. What tolerance and repeatability can be expected? This Metav IndustryLine gauge pin is finished to a tolerance of ±0.002 mm, offering repeatable contact measurement suitable for routine inspection and setting tasks. Is the pin suitable for fixture locating and go/no‑go checks? Yes, the single gauge pin M323.J24 is intended for locating, setting and go/no‑go verification in workshop and small‑series inspection workflows. How is the pin supplied to protect its measuring surfaces? The inspection pin is supplied in a protective case, which preserves the surface finish and geometry during transport and storage. Which environments is this workshop version designed for? The workshop version of this gauge pin combines durable special steel construction with a finish aimed at everyday metrology tasks in machine shops, assembly areas and maintenance workshops. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
19.25mm Gauge Pin Single 50mm Length Workshop Finish - Metav IndustryLine
Take advantage of precise dimensional control with a 19.25 mm diameter test pin in a robust workshop version, supplied in a single-piece design for simple inventory and repeatable checks; the 50 mm length and ±0.002 mm variation specification support tight tolerance inspections. Order directly via Metav Werkzeuge or ask the consultants for application advice. Test Pin M323.J25 – 19.25 mm Ø, 50 mm length, workshop version (Metav IndustryLine) A Test Pin M323.J25 engineered for reliable end-dimension checks and repeatable go/no-go assessment in workshop inspection and fixture set-up applications Workshop version for routine inspection Diameter 19.25 mm for end‑dimension control Length 50 mm for recessed measurement access Accuracy ±0.002 mm for tight tolerances Repeatable precision for routine quality control The workshop design delivers a single test pin that supports frequent verification tasks without complex set‑up. With a nominal diameter of 19.25 mm and a declared variation of ±0.002 mm, the component is suited for quality checks where narrow tolerances are required. The compact 50 mm shank length keeps handling straightforward while ensuring the contact geometry remains stable; this reduces measurement scatter and speeds up inspection cycles, making the pin an efficient choice for batch runs and fixture checks. Handling and durability tailored to the shop floor Built as a workshop version, the pin combines manageable weight with robust construction to withstand repetitive use. The 50 mm length and solid shank allow safe insertion into gauges and fixtures while maintaining alignment under typical manual handling. The design minimises the need for protective measures between uses and makes the component easy to store alongside other inspection artefacts, supporting a pragmatic workflow in maintenance and production environments. Material choice and measurement security Manufactured from special steel, the pin offers consistent surface hardness and wear resistance that preserve dimensional integrity over many cycles. The material selection favours longevity under contact loads and reduces fretting that can alter nominal diameters over time. For traceable inspection regimes, the declared accuracy of ±0.002 mm provides a clear specification to match inspection plans and gauge capacities, enabling confident decisions during acceptance and set‑up procedures. Practical integration into inspection routines The single‑piece geometry simplifies inventory control and replacement policies within a metrology department. The pin’s nominal diameter and length make it compatible with common fixture layouts and reference gauges used in mechanical workshops. Clear, measurable specifications support procurement and documentation processes, while the compact design facilitates rapid checks on assembled parts, bores and end faces without time‑consuming reconfiguration. For assured dimensional control, choose the Metav IndustryLine test pin and contact Metav Werkzeuge for tailored advice or to discuss compatibility with existing gauges — email info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: M323.J25 GTIN: 4061905072291 Brand: Metav IndustryLine Name: Test pin, single, 19.25 mm Ø, 50 mm length Weight: 0.2 kg Facts Diameter: 19.25 mm Length: 50 mm Tolerance / variation: ±0.002 mm Nominal measurement range: 19.25 mm Special features Material: special steel Workshop version for routine use Single‑piece test pin Category: Test pins FAQ What inspection tasks is this test pin suited for? The test pin M323.J25 is suitable for end‑dimension checks, go/no‑go assessments and fixture verification where a 19.25 mm diameter reference with ±0.002 mm variation is required. Is the pin compatible with standard bore gauges and fixtures? Yes; the 19.25 mm nominal diameter and 50 mm length make the component compatible with common workshop gauges and fixture layouts used for mechanical assemblies. What material is the pin made from and why does this matter? The pin is made from special steel, chosen for wear resistance and dimensional stability so that the reference diameter remains reliable over repeated contact cycles. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
19.26mm Gauge Pin Single 50mm Length Workshop Finish - Metav IndustryLine
Take advantage of the combination of workshop-grade robustness, ±0.002 mm accuracy and compact 50 mm length for reliable end‑measurement and fixture referencing; order the M323.J26 gauge pin directly via Metav Werkzeuge or ask our consultants for application advice. M323.J26 gauge pin — 19.26 mm diameter, 50 mm length (Metav IndustryLine) The M323.J26 gauge pin is a workshop‑grade precision test pin designed for end‑measurement, reference checks and fixture alignment in general mechanical and toolmaking applications. Workshop-quality execution Precise diameter 19.26 mm Hardened special steel, length 50 mm Robust workshop design for everyday reference tasks The compact construction is tailored to the realities of an industrial workshop: a workshop-quality finish and a sturdy geometry make the measuring pin suitable for repeated insertion into jigs, gauges and locating holes without rapid wear. With a 50 mm shaft length and a tight nominal diameter of 19.26 mm, the pin serves as a stable reference during assembly, setting and inspection tasks. This design reduces setup time and increases process repeatability, so fixtures can be referenced quickly and reliably across shifts. Precision that supports tighter tolerances and fewer reworks Manufactured from special steel and specified to ±0.002 mm runout and diameter variance, the test pin offers measurable improvements in positional control when used as a stop or datum element. In practice, a tolerance of ±0.002 mm means repeatable contact points and consistent part orientation, which lowers scrap rates and accelerates quality control cycles. The material and heat treatment provide surface hardness and wear resistance, maintaining the nominal size over many cycles and ensuring long‑term dimensional stability. Practical handling, transport and integration into inspection workflows Delivered in a protective transport case, the measuring pin is ready for safe storage and mobility between workstations. The compact weight (approx. 0.2 kg) and clear identification via the SKU make inventory management and retrieval straightforward. As a single gauge pin, it is suitable for both standalone reference use and as part of a set for serial inspection. The robust finish and geometry support reliable seating in locating bores, while the straightforward form factor permits easy integration into go/no‑go fixtures or modular inspection nests. Contact Metav Werkzeuge for tailored advice on integrating the M323.J26 gauge pin into existing fixtures and for procurement from our Emmerich distribution centre Technical data Article number: M323.J26 GTIN: 4061905072307 Label: Prüfstift, einzeln, 19,26 mm Länge 50 mm Manufacturer: Metav IndustryLine Facts Diameter: 19.26 mm Length: 50 mm Accuracy: ±0.002 mm Weight: 0.2 kg Special features Material: Special steel Workshop execution Delivered in protective transport case Category: Gauge pin (Messstifte) FAQ What materials is the pin made from and how does that affect wear? The M323.J26 gauge pin is manufactured from special steel, which is selected and treated to provide high surface hardness and good wear resistance for prolonged use in locating and inspection duties. Is the 19.26 mm size nominal or calibrated? The diameter is a nominal 19.26 mm dimension; the M323.J26 test pin is produced to a tolerance of ±0.002 mm to ensure consistent contact points in precision fixtures and gauges. Can the pin be used in fixture alignment and setting operations? Yes, the gauge pin is intended for end‑measurement, fixture referencing and alignment tasks; its compact 50 mm length and robust finish make it suitable for repeated seating in locating bores. How is the pin delivered and how should it be stored? The item is supplied in a protective transport case to avoid damage during transit; storage in the case keeps the pin clean and prevents accidental knocks that could affect accuracy. Does the product have a traceable identifier for stock and procurement? Yes, the M323.J26 gauge pin is listed with GTIN 4061905072307 and the SKU M323.J26 for unambiguous identification in procurement and inventory systems. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
19.27mm Gauge Pin Length 50mm Workshop Version Special Steel - Metav IndustryLine
Take advantage of a compact, workshop‑ready reference that combines high repeatability (±0.002 mm) with a 19.27 mm diameter and a 50 mm length to simplify end‑measure checks and fixture set‑up. Order the gauge directly via Metav Werkzeuge or contact the technical team for compatibility advice. Gauge pin M323.J27 — 19.27 mm diameter, 50 mm length | Metav IndustryLine The Gauge pin, single, 19.27 mm, 50 mm length is a precision reference pin designed for reliable end‑measure and assembly checks in workshop and inspection environments. Metav IndustryLine workshop version Diameter 19.27 mm precision gauge Length 50 mm, compact reference pin Tolerance ±0.002 mm high accuracy Consistent reference for end‑measure verification A compact precision element for dimensional control, this reference pin provides a stable contact surface for end‑measure inspections and go/no‑go checks. With a nominal diameter of 19.27 mm and a verified tolerance of ±0.002 mm, the component reduces measurement scatter when inserted into gauges, fixtures or mating bores; the low geometric deviation supports repeatable readings and shortens setup times in routine quality checks. The design suits bench inspection as well as integration into semi‑automated checking stations. Robust construction tailored for workshop conditions Manufactured from special steel, the pin delivers resistance to wear and a predictable surface finish that preserves fit tolerances during repeated use. Its 50 mm length balances handling convenience and sufficient engagement depth for secure seating in many fixtures, while the compact form minimises the risk of lateral flexing in short‑reach applications. The workshop version emphasises practical handling: the geometry is designed for easy placement and removal, ensuring fast part alignment and reduced cycle times during inspection or assembly. Easy integration into quality workflows and traceable stock keeping Intended as a reliable datum for small‑bore checks and fixture set‑up, the pin can be stored alongside tool‑room kits or kept in calibration sets for rapid access. The Metav IndustryLine origin and the supplied article references (M323.J27, GTIN 4061905072314) simplify inventory management and traceability across quality documentation. For inspection rooms requiring consistent reference parts, this compact gauge pin supports reproducible results and integrates into existing jigs without additional modification — making it a practical choice for machine shops and inspection benches that demand dependable outcomes. Contact Metav Werkzeuge for tailored advice on integrating the Metav IndustryLine gauge pin M323.J27 into inspection fixtures and to arrange sample checks or batch supply. Technical data Article number: M323.J27 GTIN: 4061905072314 Label: Gauge pin, single, 19.27 mm, length 50 mm Facts Diameter: 19.27 mm Length: 50 mm Tolerance: ±0.002 mm Weight: 0.2 kg Special features Workshop version Material: Special steel Compact reference pin for end‑measure applications FAQ What tolerance does the gauge pin hold? The gauge pin M323.J27 is specified with a tolerance of ±0.002 mm, providing a high‑precision reference for end‑measure checks. Is the gauge pin suited for fixture alignment and jigging? Yes, the single gauge pin from Metav IndustryLine is designed as a compact reference for fixture set‑up and aligns readily with common inspection jigs. What material is used for this pin and how does it affect wear? The part is made from special steel; this material offers a durable contact surface that maintains fit and minimises wear under normal workshop use. How is the item identified for stock and quality records? Identification is simplified by the article number M323.J27 and GTIN 4061905072314, which help with traceability and inventory control. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
19.28mm Gauge Pin 50mm Length Workshop Version - Metav IndustryLine
Combine the ±0.002 mm tolerance with a special steel construction to secure precise, repeatable inspection results and long service life; supplied ready for safe transport in a protective case. Order the gauge pin directly via Metav Werkzeuge or contact our consultants for specification advice and delivery options. Gauge pin M323.J28 – 19.28 mm diameter, 50 mm length (Metav IndustryLine) A gauge pin M323.J28 designed for end‑dimension verification and fixture alignment in workshop and production metrology. High accuracy ±0.002 mm Special steel for wear resistance 19.28 mm diameter, 50 mm length Supplied in protective transport case Streamlined inspection through measurable precision The M323.J28 gauge pin delivers a very tight manufacturing tolerance of ±0.002 mm, which directly reduces measurement uncertainty during go/no‑go checks and alignment tasks. This level of precision shortens inspection routines because fewer repeat measurements are needed to confirm conformity. The stated tolerance is a measurable, technical advantage for quality control processes where consistent end‑dimension verification improves throughput and lowers the risk of downstream rework. Robust design for everyday workshop demands Constructed from special steel, this test pin is built to withstand the knocks and handling typical in a busy workshop environment while maintaining its dimensional stability. The 50 mm length and compact mass (approx. 0.2 kg) make the pin easy to handle and position in fixtures or gauging rigs. The workshop‑grade specification emphasises durability: resistance to wear means longer intervals between replacements and stable results over many inspection cycles. Practical applications and handling benefits The pin’s 19.28 mm diameter is intended for precise end‑size checks, plug gauging, and setup of jigs and fixtures in both production and inspection areas. Supplied individually, the component is ideal where single, traceable reference pins are required for repetitive alignment tasks or dimensional spot checks. The inclusion of a protective transport case supports safe storage and reduces the chance of damage that would affect accuracy, thereby protecting the measurement chain and supporting consistent quality decisions on the shop floor. For workshop‑grade precision from Metav IndustryLine, contact Metav Werkzeuge to discuss supply quantities, delivery times and suitability for specific inspection routines. Technical Data Article number: M323.J28 GTIN: 4061905072321 Label: Gauge pin, single, 19.28 mm diameter, 50 mm length Facts Diameter: 19.28 mm Length: 50 mm Tolerance: ±0.002 mm Weight: 0.2 kg Special features Material: Special steel Workshop version Supplied in protective transport case Brand: Metav IndustryLine FAQ What is the intended use for this gauge pin? The M323.J28 gauge pin is intended for end‑dimension verification, plug gauging and fixture alignment in workshop and production metrology. Is the pin suitable for repeated shop‑floor use? Yes, the special steel construction and workshop design make the Metav IndustryLine gauge pin suitable for frequent use while maintaining dimensional stability. What accuracy can be expected when using this test pin? The pin is manufactured to a tolerance of ±0.002 mm, providing a high level of repeatability for go/no‑go checks and alignment tasks. Does the product come with protective packaging? The gauge pin is supplied individually and includes a protective transport case to reduce the risk of damage during handling and storage. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
19.29mm Test Pin 50mm Length Workshop Version - Metav IndustryLine
The combination of precision tolerance ±0.002 mm, a diameter of 19.29 mm and a robust 50 mm length yields a reliable gauge for end-measurements and workshop inspection tasks; benefit from repeatable results and stable handling in routine checks. Order the test pin M323.J29 directly via Metav Werkzeuge or ask our consultants if needed. Test pin M323.J29 — single gauge pin, 19.29 mm diameter, 50 mm length Test pin M323.J29 is a single-piece inspection pin designed for precise end-measurements and workshop checking of bore and shaft diameters. Workshop version, robust design Diameter 19.29 mm, close tolerance Dimensional accuracy ±0.002 mm 50 mm overall length for stable handling Consistent accuracy for routine inspection The gauge pin is manufactured to a tight tolerance of ±0.002 mm, ensuring repeatable dimensional checks in production and quality control. The specified accuracy supports go/no-go verification and precise end-measurements where small deviations can lead to scrap or rework. Made from special steel, the pin maintains form stability under regular use; wear‑resistant properties reduce the frequency of replacement and help to secure process reliability on the shop floor. Practical handling and application benefits With a 19.29 mm diameter and a 50 mm length, this single gauge pin offers an advantageous balance between reach and rigidity for common inspection tasks. The compact length reduces flex during insertion and retraction, providing steady contact for internal and external gauging operations. The design suits workshop routines where quick, dependable checks are required, supporting efficient in‑line control without complex fixturing. Traceability and workshop readiness Supplied as a single precision pin with a clear article code, the item is ready to be integrated into inventory and inspection logs; SKU M323.J29 and GTIN 4061905072338 facilitate traceable ordering and stock management. The unit weight of 0.2 kg and its single‑piece construction simplify handling and storage. For buyers seeking dependable dimensional references in assembly, inspection or toolroom environments, this gauge pin provides a straightforward, low‑complexity solution. Order the single test pin from Metav IndustryLine via Metav Werkzeuge for workshop‑grade accuracy and straightforward stock integration — contact Metav Werkzeuge for specification advice or procurement details. Technical data Article number: M323.J29 GTIN: 4061905072338 SKU: M323.J29 Facts Diameter: 19.29 mm Length: 50 mm Tolerance: ±0.002 mm Weight: 0.2 kg Special features Material: special steel Single test pin for end-measurements Workshop version Category: Gauge pins FAQ What tolerance is guaranteed for this test pin? The test pin M323.J29 is manufactured to a tolerance of ±0.002 mm, suitable for precise workshop inspection and end-measurement tasks. Is the pin suitable for end-measurements and typical bore checks? Yes, the single gauge pin is designed for end-measurements and routine bore or shaft verification in a workshop environment. Which material is the gauge pin made from? The pin is produced from special steel, selected for dimensional stability and wear resistance under normal inspection use. How is this item identified for ordering and inventory? The item is listed as M323.J29 with GTIN 4061905072338 for unambiguous ordering and traceability. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
19.2mm Gauge Pin, Single, 50mm Length, Workshop Version - Metav IndustryLine
Take advantage of precise tolerances, robust workshop engineering and straightforward integration into gauges and fixtures to keep inspection routines reliable and reproducible. Combine 19.20 mm nominal diameter with an accuracy of ±0.002 mm and a compact 50 mm length for consistent end‑dimension checking. Order the gauge pin directly via Metav Werkzeuge or consult our specialists for specification support. Gauge pin M323.J20 – precision 19.20 mm, length 50 mm (Metav IndustryLine) The Gauge pin M323.J20 is a workshop‑grade precision pin for end‑dimension verification and fixture setting in production and inspection environments. Workshop-grade robustness for daily use Diameter 19.20 mm with ±0.002 mm accuracy 50 mm length for compact fixtures Wear‑resistant special steel construction Reliable tolerancing for routine inspection The M323.J20 delivers a ±0.002 mm accuracy that supports tight production tolerances and repeatable acceptance criteria. As a precision gauge pin, it serves as a fixed reference for go/no‑go checks, plug gauges and stop faces, reducing variability in manual gauging procedures. The clear numeric tolerance allows engineers and quality technicians to link the component directly to inspection plans and statistical process control charts, ensuring traceability and straightforward documentation in quality systems. Robust design for workshop conditions Manufactured from special steel, the pin is engineered for everyday workshop use where handling and repeated seating into bores demand abrasion resistance and dimensional stability. The compact 50 mm length and nominal 19.20 mm diameter create a rigid profile that minimises deflection during insertion and withdrawal, improving measurement reliability. At approximately 0.2 kg, the component is substantial enough for secure handling while remaining easy to position in fixtures or gauge blocks. Practical integration into gauges and fixtures The single‑unit configuration simplifies inventory and replacement strategies for maintenance of gauges and jigs. With its standardised diameter and short length, the pin is suited to confined spaces and modular gauge assemblies where consistent end stops and reference points are required. Use of this precision pin helps to shorten setup times and limit rework by providing a defined physical reference that is simple to reproduce across workstations and shifts. Contact Metav Werkzeuge today to specify M323.J20 for workshop gauges and receive tailored advice and fast delivery from our Emmerich facility Technical data Article number: M323.J20 GTIN: 4061905071812 Brand: Metav IndustryLine Category: Gauge pin Material: Special steel Nominal diameter: 19.20 mm Length: 50 mm Accuracy: ±0.002 mm Weight: 0.2 kg Special version: Workshop execution Facts Diameter: 19.20 mm Length: 50 mm Tolerance: ±0.002 mm Weight: 0.2 kg Special features Single unit test pin Wear‑resistant special steel Workshop execution SKU: M323.J20 FAQ What is the nominal diameter and tolerance of this pin? The gauge pin M323.J20 has a nominal diameter of 19.20 mm with an accuracy of ±0.002 mm, suitable for precise end‑dimension checks. Which material is used for the pin? The component is made from special steel designed for wear resistance and dimensional stability in workshop environments. Is this pin suitable for installation in modular gauges? Yes, the 50 mm length and standardised 19.20 mm diameter make the pin well suited to modular gauge assemblies and compact fixtures. How does this pin support production quality control? As a repeatable physical reference, the M323.J20 reduces measurement variability, simplifies setup and ties directly into inspection routines and documentation. What identifier should be used when ordering replacements? Order replacements using SKU M323.J20 and the GTIN 4061905071812 to ensure the correct workshop‑grade test pin is supplied. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
19.31mm Gauge Pin 50mm Length Workshop Version, Special Steel - Metav IndustryLine
Take advantage of the combination of precise 19.31 mm diameter, 50 mm length and ±0.002 mm tolerance for reproducible end‑measure checks; the workshop‑grade construction and protective transport case keep tools ready for daily use. Order this gauge pin directly via Metav Werkzeuge or consult our specialists for application advice. Gauge pin M323.J31 — single precision test pin, 19.31 mm diameter, 50 mm length (Metav IndustryLine) The Gauge pin M323.J31 is a single, precision test pin designed for reliable end‑measure verification and workshop gauging tasks where repeatable dimensional control is required. Workshop‑grade construction Diameter 19.31 mm tolerance ±0.002 mm Length 50 mm for end‑measure checks Supplied in protective transport case Consistent end‑measure verification that keeps inspection moving The gauge pin is engineered for stable, repeatable contact in end‑measure applications; its 19.31 mm nominal diameter combined with a stated ±0.002 mm tolerance provides a clear, measurable basis for pass/fail decisions in production and inspection. Using a single, carefully finished pin for reference measurements reduces variability compared with ad‑hoc gauges and helps to document compliance during routine checks. The compact 50 mm length offers sufficient reach while keeping the contact geometry stiff for short end‑measure tasks, which contributes to quicker, more reliable checks and fewer reworks. Durable construction for frequent workshop use Made from special steel and delivered as a workshop‑grade execution, the test pin resists wear under typical contact conditions and maintains its profile over many measurement cycles. The material choice ensures good surface hardness and abrasion resistance without compromising the measuring face geometry, so the gauge pin remains a dependable reference in busy production environments. This focus on robustness means longer intervals between inspections of the gauge itself and therefore less downtime for the inspection process. Practical handling, storage and traceability for everyday use The item is supplied individually and packaged in a protective transport case, which preserves the gauge’s measuring face during storage and transit and supports safe handling on the shop floor. At a nominal weight of 0.20 kg and compact form factor, the pin is straightforward to position in fixtures or measurement setups. Clear identification via SKU and GTIN supports traceability and stock control in procurement systems, facilitating consistent replenishment and documentation across inspection routines. For reliable end‑measure verification, choose the Metav IndustryLine gauge pin M323.J31 and contact Metav Werkzeuge GmbH in Emmerich for ordering or tailored technical advice at info@metav-werkzeuge.com or +49 2822 7131930 Technical data SKU: M323.J31 GTIN: 4061905449413 Weight: 0.20 kg Length: 50 mm Diameter: 19.31 mm Material: special steel Tolerance/accuracy: ±0.002 mm Version: workshop execution Core technical data Nominal diameter: 19.31 mm Length: 50 mm Weight: 0.20 kg GTIN: 4061905449413 Accuracy: ±0.002 mm Special features Supplied individually Protective transport case included Workshop‑grade finish Suitable for end‑measure checks FAQ What is the intended use of this gauge pin? The gauge pin M323.J31 is intended for end‑measure verification and workshop gauging where a single, precise reference pin is required. How accurate is the test pin when used for inspection tasks? The test pin is specified with a tolerance of ±0.002 mm, making it suitable for fine dimensional checks and consistent pass/fail assessments. Which material is the gauge pin made from and why does it matter? The pin is made from special steel, chosen for surface hardness and wear resistance so the measuring face retains its geometry during repeated use. Is the item supplied ready for safe transport and storage? Yes, the gauge pin is supplied individually in a protective transport case which preserves the measuring face during handling and transit. Can this pin be used in automated or fixture‑based checks? Yes, the compact 50 mm length and precise diameter make the pin suitable for fixture insertion or automated probing where a stable reference is required. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
19.32mm Gauge Pin 50mm Length Workshop Finish - Metav IndustryLine
Take advantage of a compact gauge pin that combines workshop‑grade robustness with high repeatability: 19.32 mm diameter, 50 mm length and an inspection tolerance of ±0.002 mm support reliable end‑measure checks and reduce the need for rework; order via Metav Werkzeuge or request further technical details from the consultants. Gauge pin, single, 19.32 mm – 50 mm length, ±0.002 mm accuracy (Metav IndustryLine) A gauge pin, single, 19.32 mm designed for precision end‑measure verification in workshop environments and small‑part inspection tasks Workshop specification, robust design Diameter 19.32 mm for end-measure checks Accuracy ±0.002 mm (2 µm) for fine gauging Delivered in transport case for safe handling Precision that reduces rework and inspection time The instrument offers a measured diameter of 19.32 mm with a stated tolerance of ±0.002 mm (equivalent to 2 µm), making it suitable for demanding end‑measure applications where dimensional conformity is critical. This level of accuracy minimises uncertainty during go/no‑go verifications and inline checks, so inspection processes become more predictable and corrective loops are shortened. The compact geometry and tight tolerance support consistent contact conditions when used as a reference pin, improving overall process stability and reducing the likelihood of part rejigs. Durable workshop design for repeated handling Constructed from special steel and specified as a workshop execution, the pin balances wear resistance with manageable mass (approx. 0.2 kg) for routine use on the shop floor. The solid construction resists surface deformation under normal handling and maintains measuring integrity over long service intervals. Delivery in a dedicated transport case protects the datum surfaces during storage and transit, preserving the pin’s measuring faces and extending usable life in busy production or inspection environments. Practical classification and application guidance Classified in the micro measurement range (maximum span 10–100 mm), this single gauge pin is optimised for fine mechanical work where compactness and stiffness are priorities—typical tasks include end‑measure checks on turned parts, fixture set‑up and go/no‑go verifications. The compact length of 50 mm is compatible with common fixtures and allows straightforward insertion into bores or assembly jigs for repeatable seating. The workshop variant is aimed at machinists and inspection technicians who require a rugged, easily stored reference pin for everyday quality control. Contact Metav Werkzeuge today for specification matching or to obtain the Metav IndustryLine gauge pin directly from our Emmerich stock; technical queries can be sent to info@metav-werkzeuge.com or discussed by phone at +49 2822 7131930 Technical data SKU: M323.J32 GTIN: 4061905449475 Material: Special steel Length: 50 mm Diameter: 19.32 mm Numbers / core technical data Measurement range (min/max): 19.32 mm / 19.32 mm Tolerance / accuracy: ±0.002 mm Weight: 0.2 kg Special features Workshop execution (robust design) Single gauge pin Delivered in transport case for transport protection Intended use: end‑measure checks FAQ What is the declared accuracy of this gauge pin? The gauge pin is specified with an accuracy of ±0.002 mm (2 µm), suitable for fine end‑measure verifications. Is the pin suitable for daily workshop use? Yes; the workshop execution and special steel construction make the measuring pin appropriate for routine handling and inspection tasks. Can this pin be used in fixture set‑ups for small parts? The 50 mm length and 19.32 mm diameter are compatible with common jigs and fixtures used for small‑part alignment and end‑measure checks. How is the pin protected during transport and storage? Delivery includes a transport case to protect the datum surfaces during handling and storage. Which measurement range category does this pin belong to? This product falls into the micro range (maximum 10–100 mm), optimised for compact, high‑precision applications. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
19.33mm Gauge Pin 50mm Length Workshop Version Special Steel - Metav IndustryLine
High-precision workshop pin with 19.33 mm diameter and ±0.002 mm tolerance provides reproducible end-measure checks and reduces inspection-related rework; its robust special-steel construction and 50 mm shank keep handling simple in daily use. Order the gauge pin directly via Metav Werkzeuge or consult the technical team for application advice. Gauge pin M323.J33 — single, 19.33 mm diameter, 50 mm length (Metav IndustryLine) The gauge pin M323.J33 is a workshop-grade inspection pin designed for end-measure, bore and fit verification in production and maintenance environments. Workshop-grade execution Diameter 19.33 mm, length 50 mm Tolerance ±0.002 mm Accuracy that lowers inspection uncertainty The inspection pin is specified with a tolerance of ±0.002 mm, which makes it suitable for precise end-measure checks where tight clearances matter. This level of control reduces the need for repeated measurements and supports consistent acceptance decisions on bore fits and reference gauges. The combination of exact nominal diameter and low variation assists quality teams in maintaining traceable results and reducing scrap rates during routine checks. Durable construction for everyday workshop use Built as a workshop-grade tool from special steel, the pin withstands frequent handling and contact with mating surfaces while preserving its measurement integrity. The 50 mm shank gives a comfortable grip and straightforward positioning in bores and gauges, and the modest mass aids in stable placement without unnecessary bulk. Supplied as a single unit and protected for transport, this pin is suitable for bench inspection and mobile measuring kits alike. Designed to integrate into standard inspection processes As a single gauge pin for spot verifications and calibration checks, the component slips easily into inspection routines alongside plug gauges and handheld measurement devices. Clear identification with SKU and GTIN allows orderly inventory management and quick replacement when reference sets are synchronised. Using a standardised inspection pin streamlines documentation and supports reproducible measurement protocols in production and workshop environments. Contact Metav Werkzeuge today for ordering or technical guidance on the Metav IndustryLine gauge pin M323.J33 — phone +49 2822 7131930 or email info@metav-werkzeuge.com Technical Data SKU: M323.J33 GTIN: 4061905449482 Manufacturer: Metav IndustryLine Label: Gauge pin, single, 19.33 mm, length 50 mm Facts Diameter: 19.33 mm Length: 50 mm Weight: 0.2 kg Tolerance: ±0.002 mm Special features Workshop-grade execution Material: Special steel Delivered in transport case for transport Category: Gauge pins FAQ What level of accuracy does this gauge pin offer? The gauge pin M323.J33 is specified with a tolerance of ±0.002 mm, providing tight reproducibility for end-measure and bore checks. Is the pin suitable for everyday workshop inspection? Yes. The Metav IndustryLine workshop version is designed for regular use, combining robust special steel construction with a practical 50 mm shank for handling. How is the product supplied for transport and storage? The inspection pin is delivered as a single unit and protected in a transport case suitable for workshop logistics. Can this pin be used with standard plug-gauge procedures? The gauge pin M323.J33 is intended for spot verifications and calibration comparisons alongside plug gauges and handheld measuring tools. Where can the product be ordered or further technical information obtained? Ordering and detailed technical questions can be directed to Metav Werkzeuge; the product is listed under SKU M323.J33 and GTIN 4061905449482. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
19.34mm Gauge Pin Length 50mm Workshop Finish - Metav IndustryLine
The combination of a highly specific diameter, workshop‑grade construction and a tight ±0.002 mm tolerance delivers repeatable end‑measure checks and robust shop‑floor performance; order the gauge pin directly via Metav Werkzeuge or consult our specialists for application advice. Gauge pin M323.J34 — Single precision test pin, Ø 19.34 mm, 50 mm length (Metav IndustryLine) The Gauge pin M323.J34 is a single precision test pin designed for end‑measure verification and reference fitting tasks in workshop and inspection environments. Precision diameter 19.34 mm Tight tolerance ±0.002 mm Workshop‑grade, robust construction Reliable fit checking for repetitive tasks A compact test pin with a nominal diameter of 19.34 mm and a slender 50 mm length is optimised for repeated end‑measure checks and reference fitting operations. The combination of a controlled diameter and a ±0.002 mm dimensional variation ensures that go/no‑go assessments and clearance verifications remain consistent across batches. In practice, this reduces rework and speeds up quality checks because measurements that rely on a stable reference pin become directly comparable shift to shift. Built for the workshop — durable and easy to handle Constructed from special steel in a workshop specification, this single pin offers resistance to everyday wear while remaining easy to handle on the shop bench. The robust finish withstands handling and provides a reliable mating surface for gauges and fixtures, so routine checks keep their accuracy without frequent replacement. The mechanical simplicity of a single‑piece test pin also makes it straightforward to integrate into inspection jigs or to use as a portable reference during set‑up and alignment work. Precision where it matters — traceable geometry With a declared positional accuracy of ±0.002 mm, the pin is suitable for fine tolerance applications where repeatability is critical. The tight manufacturing tolerance means the pin can serve as a reference for dimensional comparisons and quick functional checks of mating bores and gauge assemblies. Being a single test pin, it is particularly useful for end‑dimension verification and as a calibrated reference in routine quality control. Practical handling and workshop benefits Weighing approximately 0.2 kg, the pin balances tactile feel with sufficient mass for steady placement during inspection. The workshop execution ensures practical features such as robust surfaces and straightforward geometry, which helps maintain consistent contact conditions during measuring tasks. For production environments that demand reliable, repeatable reference tools, this pin reduces measurement variability and supports a smoother inspection workflow. Contact Metav Werkzeuge in Emmerich for tailored delivery and technical advice — Metav Werkzeuge GmbH, Parkring 45, Emmerich; phone +49 2822 7131930; email info@metav-werkzeuge.com Technical data Article number: M323.J34 GTIN: 4061905449499 Material: Special steel Weight: 0.2 kg Length: 50 mm Diameter: 19.34 mm Accuracy: ±0.002 mm Core measurements Measuring range (nominal diameter): 19.34 mm Measuring range min: 19.34 mm Measuring range max: 19.34 mm Length: 50 mm Special features Single test pin (single piece) Workshop execution Intended for end‑measure verification FAQ What is the primary application for this gauge pin? The gauge pin M323.J34 is intended for end‑measure verification and reference fitting tasks, providing a repeatable reference for bore and fit checks in workshop and inspection settings. What material is used for the pin and how does that affect durability? Made from special steel, the pin offers enhanced surface durability suitable for routine shop‑floor handling and repeated contact with mating parts. How tight is the manufacturing tolerance on the pin? The pin is produced to a tolerance of ±0.002 mm, which supports precise and repeatable fit checks where small dimensional deviations matter. Can this pin be used as a reference in jig and fixture set‑up? Yes; the stable diameter and workshop design make the pin suitable as a reference component for aligning jigs, fixtures and mounting assemblies. Is the pin supplied as a set or individually? This item is supplied as a single precision test pin, reference M323.J34. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
19.35mm Test Pin Single 50mm Length Workshop Version - Metav IndustryLine
Take advantage of the combination of ±0.002 mm accuracy, 19.35 mm nominal diameter and a 50 mm length for stable, repeatable end‑measurements; order via Metav Werkzeuge or consult our advisors for application support. Metav IndustryLine Gauge Pin, single — 19.35 mm diameter, 50 mm length The Metav IndustryLine gauge pin, single 19.35 mm, 50 mm length is a compact reference pin for end‑measurements and go/no‑go checks in workshop inspection and small‑part assembly applications. High accuracy ±0.002 mm Nominal diameter 19.35 mm 50 mm overall length for stability Workshop design for robust use Precision for repeatable end‑measurements The gauge pin is produced for applications where measurement reproducibility matters: with an accuracy of ±0.002 mm, the pin functions as a stable reference for fit checks and end‑dimension controls. Classified in the micro range (maximum measuring span 10–100 mm), this compact format suits fine mechanical tasks and short‑reach inspections, where low leverage and minimal deflection are essential. The 19.35 mm nominal diameter is presented as a calibrated reference size for match and clearance tests, reducing the iteration time in quality routines and improving throughput in small‑batch production. Durability and handling that suits workshop routines Manufactured from special steel, the component is intended as a workshop version that resists everyday wear while maintaining dimensional integrity. The 50 mm length adds axial stability during insertion and retrieval, helping to avoid tilting or edge contact that can skew results. At approximately 0.2 kg, handling remains practical for bench use; the solid construction simplifies repetitive checking procedures and minimises downtime caused by part replacement. This balance of stiffness and manageability supports faster inspection cycles and consistent judgement calls on assembly lines. Integration into inspection and process control workflows As a single, traceable inspection element, the pin is useful for setting references in comparative gauges, verifying bore fits and confirming end‑measurements during assembly. The item ships as a singular gauge pin with clear identification (GTIN and SKU), easing inventory control and reordering. In process sequences, the pin reduces setup complexity by providing a tactile, verifiable datum that complements calipers and micrometres. For customers seeking to streamline inspection steps, the component contributes to lower process variation and more reliable end‑product conformity. Contact Metav Werkzeuge today for application advice or to secure the Metav IndustryLine gauge pin for consistent inspection results, and request assistance from our technical consultants if required. Technical Data Article number: M323.J35 GTIN: 4061905449505 Brand: Metav IndustryLine Category: Gauge pins / Measuring pins Facts Diameter: 19.35 mm Length: 50 mm Accuracy: ±0.002 mm Weight: 0.2 kg Special features Workshop version Material: special steel Single pin configuration FAQ What applications is this gauge pin suitable for? The gauge pin is suitable for end‑dimension checks, fit verifications and go/no‑go assessments in workshop inspection routines; the Metav IndustryLine gauge pin, single 19.35 mm (SKU M323.J35) provides a compact, repeatable reference for these tasks. How precise is the Metav IndustryLine gauge pin for inspection use? With a stated accuracy of ±0.002 mm, the Metav IndustryLine pin delivers the precision required for fine measurement tasks and repeatable fit testing in small‑part production and quality control. Can the gauge pin be used in automated or semi‑automated checks? Yes. The single 19.35 mm gauge pin can be incorporated as a physical datum in fixtures and semi‑automated checks where a tactile reference is needed to confirm bore sizes or mating fits. What material and durability can be expected from this pin? The pin is made from special steel and specified as a workshop design, offering enhanced robustness for regular use while retaining dimensional stability over repetitive inspection cycles. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
19.36mm Gauge Pin 50mm Length Workshop Version - Metav IndustryLine
Take advantage of the combination of Ø 19.36 mm diameter, ±0.002 mm accuracy and robust special steel for reliable end‑measure checks in workshop environments — order the pin gauge directly via Metav Werkzeuge or ask our consultants if needed. Pin gauge M323.J36 — single pin gauge, Ø 19.36 mm, 50 mm length (Metav IndustryLine) The pin gauge M323.J36 is a single, workshop‑grade gauge pin designed for precise end‑measure checks and go/no‑go verification in production and inspection settings. Workshop version for everyday use Diameter Ø 19.36 mm with tight tolerance Accuracy ±0.002 mm for repeatable checks Manufactured from special steel for durability Precision where it matters most A compact gauge pin with a diameter of 19.36 mm and an accuracy of ±0.002 mm offers the kind of repeatability that reduces rework and speeds up inspection cycles. The tight tolerance is not an abstract figure: it means consistent pass/fail decisions when checking bores, through‑holes or mating features during final inspection. By using a hardened, dimensionally stable measuring element, inspection intervals become predictable and measurement variation is minimised. The result is fewer downstream faults and a smoother production flow. Built for the workshop environment Designed as a workshop version, this gauge pin combines a 50 mm length with a sturdy special steel construction to withstand everyday handling and light impacts typical at the bench. The geometry and surface finish are optimised to resist wear during repeated insertion and removal, which preserves nominal diameter over many cycles. The modest weight supports comfortable manual use while the compact form factor makes storage and handling straightforward for technicians and quality staff alike. Integrates into established inspection routines As a member of the pin gauges category, this single gauge pin is ideal for end‑measure and go/no‑go applications on shafts and bores where a specific diameter check is required. Its simple design supports rapid checks without the need for elaborate fixturing, enabling faster throughput on the inspection bench. Traceable identification (SKU M323.J36, GTIN 4061905449512) makes inventory and tool management easier, while the material choice and workshop specification ensure longevity under frequent use. This component is a practical tool when accuracy and durability are both priorities. For workshop purchases or technical advice on using the pin gauge, contact Metav Werkzeuge for local stock and specialist guidance; Metav Werkzeuge is ready to advise on compatibility and inspection workflows Technical data Article number: M323.J36 GTIN: 4061905449512 Label: Pin gauge, single, Ø 19.36 mm, length 50 mm Manufacturer: Metav IndustryLine Facts Diameter: 19.36 mm Length: 50 mm Weight: 0.2 kg Accuracy: ±0.002 mm Special features Material: Special steel Workshop version Category: Pin gauges Application hint: End‑measure checks FAQ What level of accuracy does this gauge provide? The pin gauge M323.J36 from Metav IndustryLine is specified with an accuracy of ±0.002 mm, suitable for repeatable end‑measure and go/no‑go checks. Is the gauge suitable for frequent workshop use? Yes. The workshop version is made from special steel and designed for routine handling and repeated insertion cycles typical in production environments. Which measurements is this pin gauge intended for? This single gauge pin is intended for end‑measure checks of bores and shafts where a precise Ø 19.36 mm verification is required. How is the product identified for inventory and traceability? The item is listed as SKU M323.J36 with GTIN 4061905449512, which supports clear inventory tracking and tool management. Does the product specification include the material used? Yes. The specification names special steel as the material, which balances hardness and wear resistance for workshop applications. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
19.37mm Gauge Pin, Single, 50mm Length, Workshop Version - Metav IndustryLine
Take advantage of the combination of 19.37 mm diameter, ±0.002 mm accuracy and a 50 mm length in a workshop-grade gauge pin for reliable end-dimension checks; order the gauge pin directly via Metav Werkzeuge or ask our consultants if needed. Gauge pin M323.J37 – single gauge pin, 19.37 mm Ø, 50 mm length (Metav IndustryLine) Gauge pin M323.J37 is a workshop-grade fixed-diameter pin for precise end‑dimension checks, fixture setting and go/no‑go reference tasks in metalworking environments Workshop-grade construction Diameter 19.37 mm ±0.002 Special steel for durability Supplied in transport case Precision where it counts for repeatable checks The M323.J37 gauge pin provides a fixed 19.37 mm diameter with an inspection tolerance of ±0.002 mm, delivering measurable accuracy for end‑dimension verification and fixture alignment. The tight tolerance reduces uncertainty during go/no‑go checks and simplifies pass/fail decisions on production lines. Using a fixed‑diameter reference makes it straightforward to compare bore sizes, check alignment pins and set up fixtures without iterative adjustment, improving throughput in repetitive tasks. Built for workshop use and long service life Designed as a workshop-grade item, the pin is manufactured from special steel chosen for wear resistance under regular handling and contact with mating components. The 50 mm overall length offers a stable insertion depth while remaining compact enough for handheld use and fast positioning. The robust surface and solid construction minimise deformation risk under typical workshop loads, so the pin maintains dimensional integrity over many inspection cycles and reduces the need for frequent replacements. Practical handling and transport support efficiency Supplied singly and delivered in a transport case, the pin is protected during storage and transit to the shop floor, helping to preserve its calibrated diameter from knocks and contamination. The modest mass and compact form factor make the item easy to handle in assembly jigs and inspection nests. For tasks that require a dedicated reference gauge at several stations, having a protected, ready‑to‑use pin avoids downtime and simplifies inventory management. Suitable applications and compatibility The single gauge pin is well suited to end‑dimension control, locating and alignment tasks in general metalworking, fixture construction and quality control benches. As a simple, fixed‑dimension reference it complements micrometrology tools and precision fixtures by providing a stable physical datum. The combination of workshop specification, special steel and ±0.002 mm tolerance positions the pin as a reliable tool for repeatable checks where small deviations matter. Trust the Metav IndustryLine accuracy — contact Metav Werkzeuge in Emmerich at info@metav-werkzeuge.com or +49 2822 7131930 to request the M323.J37 gauge pin and arrange delivery from stock Technical data Article number: M323.J37 GTIN: 4061905449529 Weight: 0.2 kg Material: Special steel Facts Diameter: 19.37 mm Length: 50 mm Accuracy: ±0.002 mm Special features Workshop version Supplied in transport case Single gauge pin FAQ What is the nominal diameter and tolerance of the pin? The M323.J37 gauge pin has a nominal diameter of 19.37 mm with a dimensional tolerance of ±0.002 mm. Which material is used for the gauge pin? The pin is made from special steel, specified for workshop durability and resistance to wear under regular inspection use. Is the pin supplied individually or as a set? This item is supplied as a single gauge pin (M323.J37), delivered individually in its transport case. For which tasks is this gauge pin suitable? The gauge pin is intended for end‑dimension checks, fixture locating and alignment tasks in metalworking and quality control applications. How is the pin protected during transport and storage? The M323.J37 is supplied in a transport case to protect the diameter and surface finish during handling and transit. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
19.38mm Gauge Pin 50mm Length Workshop Version - Metav IndustryLine
Take advantage of the ±0.002 mm tolerance, the precise 19.38 mm diameter and the compact 50 mm length to secure repeatable end‑measure checks in workshop environments; order the gauge pin directly via Metav Werkzeuge or consult our team for purchase guidance. Gauge pin M323.J38 – precision 19.38 mm diameter, 50 mm length (Metav IndustryLine) The Gauge pin M323.J38 is a single precision plug gauge designed for workshop end‑measure checks, fixture alignment and reference measurements in the micro measurement range. Tolerance ±0.002 mm Diameter 19.38 mm ground to size 50 mm overall length in workshop execution Manufactured from special steel Precision where small tolerances matter This single‑piece gauge pin is engineered for dimensional checks where sub‑millimetre accuracy is required. With a declared tolerance of ±0.002 mm, the component provides the stability needed for routine verification of end‑masses and mating bores. The compact dimensions place it in the Micro range (10–100 mm) classification, which is ideal for fine‑mechanical work and applications that demand high repeatability over short measuring distances. The precise diameter and short length reduce torsion and bending during use, improving measurement certainty during go/no‑go or reference checks. Robust material and workshop design for reliable handling Manufactured from special steel and finished as a workshop version, this gauge pin combines wear resistance with practical handling characteristics. The material choice supports repeated insertion and withdrawal in jigs and fixtures without rapid surface degradation, extending service life under typical workshop conditions. The compact form factor simplifies handling during setup and inspection sequences, shortening process time and reducing the likelihood of misalignment. This translates into fewer rejected parts and less rework across production batches. Practical use and traceable identification The component’s modest weight of 0.2 kg and single‑piece delivery make it straightforward to integrate as a reference element in test benches or inspection trays. The item is listed with a GTIN for inventory control and traceability, which assists in goods management and quality documentation. Where a calibrated reference is required, please note that no ISO 17025 certificate is listed for this entry; calibration options can be confirmed separately if needed. As a compact reference gauge, it is particularly suited to quick checks, fixture set‑up and verification tasks in machining and assembly areas. For reliable workshop checks choose the Metav IndustryLine gauge pin M323.J38 and contact Metav Werkzeuge GmbH for procurement and product advice Technical data Article number: M323.J38 GTIN: 4061905449918 Manufacturer: Metav IndustryLine Facts Diameter: 19.38 mm Length: 50 mm Tolerance: ±0.002 mm Weight: 0.2 kg Special features Material: Special steel Workshop execution Application: end‑measure checks and fixture alignment Single gauge pin delivery FAQ What tolerance is specified for this gauge pin? The gauge pin M323.J38 (Metav IndustryLine) is specified with a tolerance of ±0.002 mm for dimensional checks. Which diameter and length does this item cover? This listing covers a diameter of 19.38 mm with an overall length of 50 mm for the single gauge pin M323.J38. Is an ISO 17025 calibration certificate included? No ISO 17025 calibration certificate is listed for this gauge pin; the product description does not indicate an ISO 17025 calibration. What material is the gauge pin made from? The M323.J38 is manufactured from special steel and supplied in a workshop execution for robust, repeated use. Is this pin suitable for fixture alignment and end‑measure checks? Yes, the design and dimensions of the M323.J38 make it suitable for fixture alignment, reference checks and end‑mass verification in workshop environments. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
19.39mm Gauge Pin, Workshop Version, 50mm Length - Metav IndustryLine
This single gauge pin combines precise dimensional control with robust workshop construction; its 19.39 mm diameter and tight ±0.002 mm tolerance ensure dependable hole checking and end‑measure verification. Order the gauge pin directly via Metav Werkzeuge or consult our specialists for application advice. Gauge pin, single — 19.39 mm Ø, 50 mm length (Metav IndustryLine) A gauge pin, single, 19.39 mm designed for precise hole gauging and end‑measurement tasks in workshop and production environments. Single gauge pin, Ø 19.39 mm Tolerance ±0.002 mm for tight checks 50 mm length for end‑measure applications Workshop version, robust construction Consistent precision for everyday production control The gauge pin delivers repeatable dimensional checks thanks to a nominal diameter of 19.39 mm and a verified tolerance of ±0.002 mm, which reduces the need for rework and supports reliable first‑piece inspection. Machined from special steel, the rod maintains form stability under typical workshop conditions while offering a concrete reference for bore gauges and alignment fixtures. The compact length of 50 mm minimises flex during insertion, aiding accurate end‑measurement and short‑run verification tasks. This combination of diameter accuracy and material choice supports consistent metrology outcomes across multiple operators and shifts. Robust handling and quick in‑process checks Built as a workshop version, the pin withstands regular use on shop floors and in maintenance areas without compromising measurement integrity. The design is optimised for rapid go/no‑go checks and incremental calibration routines, delivering high repeatability for frequent gauging cycles. Where speed and reliability matter, the single‑piece format cuts handling time compared with multi‑component fixtures and enables straightforward storage and retrieval in labelled racks. Practical benefits include faster set‑up, fewer measurement interruptions and clearer production decisions based on objective gauge readings. Procurement confidence and traceable identity Ordering from Metav IndustryLine ensures traceability and a clear parts identity; the article is supplied with a unique SKU and GTIN for inventory control and procurement workflows. For quality managers the visible tolerance and material declaration support documented inspection procedures and parts tracking. Metav’s presence in Emmerich acts as a quality filter for the European market, giving procurement teams confidence in repeat supply and straightforward replacement when needed. Specification clarity and part labelling also assist in onboarding the item into tool management systems or bespoke inspection plans. For application advice or to request a specification sheet for this Metav IndustryLine gauge pin, contact Metav Werkzeuge at info@metav-werkzeuge.com or call +49 2822 7131930 to ensure the right fit for workshop and production needs Technical Data SKU: M323.J39 GTIN: 4061905449925 Label: Gauge pin, single, 19.39 mm diameter, 50 mm length Category: Gauge pins Core specifications Diameter: 19.39 mm Length: 50 mm Tolerance: ±0.002 mm Weight: 0.2 kg Special features Material: Special steel Workshop version ECLASS: 21170231 Sold as a single item FAQ What tolerance does this gauge pin provide? The gauge pin has a tolerance of ±0.002 mm, ensuring tight dimensional checks for bore gauging and end‑measure tasks. Is this item supplied individually or as part of a set? This product is supplied individually; the SKU is M323.J39 for single‑item ordering and inventory tracking. Which applications is the pin suited for? Designed for hole gauging and end‑measurement, the pin suits workshop inspections, fixture checks and short‑run production verification. What material is used and how does it affect use? Made from special steel, the pin offers stability and wear resistance suitable for routine shop‑floor measurement tasks. Can this pin be used for go/no‑go checks? Yes, the single gauge format is ideal for quick go/no‑go assessments and repeatable in‑process checks. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
19.3mm Test Pin 50mm Length Workshop Version - Metav IndustryLine
Precise end-measurement capability with a 19.3 mm diameter and a tolerance of ±0.002 mm enables reliable inspection results; the 50 mm length and workshop-grade construction ensure stable handling and repeatable checks. Order the gauge pin directly via Metav Werkzeuge or ask our consultants if needed. Gauge pin, single, 19.3 mm Ø — 50 mm length (Metav IndustryLine) A gauge pin, single, 19.3 mm designed for accurate end measurements and workshop inspection tasks Diameter 19.30 mm for exact end measurements High repeatability with ±0.002 mm tolerance 50 mm length for stable handling Workshop version made from special steel Consistent measurement results through tight tolerance The core advantage of this workshop-grade pin is its precision: a diameter of 19.3 mm held to ±0.002 mm minimises uncertainty during go/no-go and end-measurement tasks. Such repeatability reduces sorting effort and rework, improving throughput in inspection routines. Where dimensional control is essential, the controlled diameter and low deviation deliver quantifiable benefits for quality assurance and inline checks. Robust construction for workshop environments Manufactured from special steel, the component offers a balance of surface hardness and wear resistance that suits repetitive contact checks. The 50 mm length provides a comfortable engagement for manual or jig-mounted inspections while keeping the mass low at 0.2 kg for straightforward handling. The workshop execution ensures durability under frequent use, supporting uptime and consistent tactile feedback during gauge operations. Traceability and practical integration into inspection processes Delivered as a single unit with a clear SKU and GTIN for inventory management, the pin is straightforward to record into inspection plans and measurement logs. Traceable identification supports batch control and simplifies replacement cycles. The product’s uncomplicated geometry makes it compatible with existing fixtures and end-measurement workflows, enabling quick adoption without complex setup or calibration procedures. For specification advice or to secure this Metav IndustryLine gauge pin (SKU M323.J30) contact Metav Werkzeuge in Emmerich for reliable supply and expert consultation Technical data Article number: M323.J30 GTIN: 4061905072345 Brand: Metav IndustryLine Label: Gauge pin, single, 19.3 mm length 50 mm Core technical data Diameter: 19.3 mm Length: 50 mm Tolerance: ±0.002 mm Weight: 0.2 kg Special features Material: Special steel Workshop execution Supplied individually Story trigger: end measurement FAQ What degree of accuracy can be expected from this gauge pin? The gauge pin from Metav IndustryLine delivers a dimensional tolerance of ±0.002 mm, providing high repeatability for end-measurement tasks. Is the material suitable for frequent contact checks? Yes, the pin is made of special steel, chosen for wear resistance and robustness in workshop inspection use. How is the product identified for inventory and traceability? The unit is listed under SKU M323.J30 and GTIN 4061905072345, facilitating clear tracking in inspection and procurement systems. Metav IndustryLine: Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
19.41mm Gauge Pin, Single, 50mm Length, Workshop Version - Metav IndustryLine
The combination of a precise 19.41 mm diameter, a tight tolerance of ±0.002 mm and a compact 50 mm length makes this inspection pin an efficient choice for fast end‑dimension checks in busy workshops; order the gauge pin directly via Metav Werkzeuge or consult our specialists for application advice. Gauge pin M323.J41 — 19.41 mm diameter, 50 mm length (Metav IndustryLine) A gauge pin M323.J41 engineered for reliable end‑dimension inspection and routine verification tasks in mechanical workshops and production control. Precision ground 19.41 mm diameter Compact 50 mm length for confined checks Tolerance ±0.002 mm for high reproducibility Consistent accuracy for end‑dimension verification The inspection pin is precision ground to a nominal 19.41 mm diameter with a declared variation of ±0.002 mm, making it suitable for comparative and go/no‑go checks where repeatability matters. Manufactured in a workshop version, the component is intended for frequent handling and quick transfer between bench fixtures; the compact 50 mm length reduces bending moment and improves handling on small assemblies. This level of control shortens inspection cycles and supports reliable process decisions. Durable material and workshop suitability Constructed from special steel, the pin combines surface hardness with resistance to wear in typical mechanical environments. The material choice and workshop specification mean the pin withstands repeated contact during routine checks and maintains geometric stability over time. The design is optimised for direct use on measuring benches and in jigs, providing a robust reference surface that keeps maintenance intervals low and inspection throughput high. Practical use and integration in inspection workflows As a single inspection pin, this product integrates simply into existing gauge sets, fixture arrays or rail systems used for end‑dimension control. The compact dimensions facilitate checks in confined areas and on small components, while the ±0.002 mm tolerance gives process engineers a reliable datum for quality gates. Where dimensional tolerances drive downstream assembly quality, this precision component acts as a fast, low‑complexity measurement aid that supports consistent production quality. For workshop‑grade precision from Metav IndustryLine, contact Metav Werkzeuge for stock status and tailored advice at info@metav-werkzeuge.com or by calling +49 2822 7131930 Technical data Article number: M323.J41 GTIN: 4061905449949 Category: Gauge pins (Messstifte) Numbers / Core data Diameter: 19.41 mm Length: 50 mm Tolerance: ±0.002 mm Weight: 0.2 kg Accuracy class: ±0.002 Designs / Special features Material: special steel Workshop version Precision ground surface Single inspection pin for end‑dimension checks FAQ What level of accuracy can be expected from this gauge pin? The gauge pin M323.J41 is specified with an accuracy of ±0.002 mm, providing reliable repeatability for routine end‑dimension inspections. Is the pin suitable for inclusion in existing gauge sets or fixtures? Yes, the single gauge pin is designed for simple integration into existing fixture arrays and gauge sets used for comparative or assembly checks. What material is used and how does that affect longevity? Made from special steel, the inspection pin offers good wear resistance for workshop environments and retains its geometric stability under frequent use. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
19.42mm Gauge Pin Length 50mm Workshop Version - Metav IndustryLine
Take advantage of the combination of high mechanical accuracy and a robust workshop design, which ensures reliable end‑measurement and repeatable checks; order directly via Metav Werkzeuge or contact our consultants for tailored advice. Gauge pin M323.J42 — single inspection pin, Ø 19.42 mm, 50 mm length (Metav IndustryLine) The gauge pin (single, 19.42 mm, 50 mm length) serves as a compact inspection and end‑measurement tool for workshop measuring and fitting verification, designed for repeatable checks in everyday production and quality control. Workshop‑grade construction for everyday use Diameter 19.42 mm with ±0.002 mm tolerance Length 50 mm for compact inspection tasks Supplied in transport case for safe handling Accurate measurements with tight tolerance for repeatable checks The M323.J42 is engineered for precision: a nominal diameter of 19.42 mm combined with a verified tolerance of ±0.002 mm gives a dependable basis for go/no‑go checks, fit testing and end‑measurements. This level of mechanical fidelity reduces ambiguity during inspection and shortens decision loops on the shop floor, because the consistent geometric form and controlled finish minimise positional error. Where traceable, repeatable measurement matters, this inspection pin behaves predictably and supports efficient quality workflows. Built for the workshop — durability and safe transport Designed as a workshop‑version tool, the pin is manufactured from special steel to withstand frequent handling and contact with assemblies. The 50 mm overall length keeps the tool compact and easy to manoeuvre in tight jigs or fixtures, while the supplied transport case protects the gauge during storage and transit, preserving the calibrated diameter. The robust design reduces downtime caused by accidental damage and keeps maintenance needs low, making it suitable for production lines and service benches alike. Sourcing, traceability and Metav support for smooth integration The product is available under Metav IndustryLine and is supplied with clear identification (SKU M323.J42, GTIN 4061905449956), allowing straightforward integration into inventory and quality systems. Metav’s European distribution hub provides dependable supply and a quality filter that supports repeat orders and larger procurement plans. For businesses seeking predictable inspection tools, this inspection pin combines measurable performance with the logistical reliability expected from an experienced precision‑specialist. Contact Metav Werkzeuge for procurement and technical consultation on Metav IndustryLine gauge pins and ensure the right inspection components are matched to production needs Technical data SKU: M323.J42 GTIN: 4061905449956 Brand: Metav IndustryLine Material: Special steel Facts Diameter: 19.42 mm Length: 50 mm Tolerance: ±0.002 mm Weight: 0.2 kg Special features Workshop version Supplied in transport case for transport protection Compact design for tight fixtures Intended for end‑measurement and fit checks FAQ What is the nominal diameter and tolerance of this gauge pin? The gauge pin has a nominal diameter of 19.42 mm with an accuracy of ±0.002 mm, suitable for precise fit and end‑measurement tasks. Is the pin suitable for frequent workshop use? Yes, the M323.J42 is a workshop‑grade inspection pin made from special steel and supplied in a transport case to resist daily handling and protect the measuring surface. How does this pin support traceability in quality systems? Identification via SKU M323.J42 and GTIN 4061905449956 allows the inspection pin to be logged into inventory and quality records, facilitating audit trails and reorder processes. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
19.43mm Gauge Pin, Single, 50mm Length, Workshop Version - Metav IndustryLine
Take advantage of a compact, high-precision reference component that combines stable seating, a Ø 19.43 mm nominal diameter and an exacting ±0.002 mm tolerance for repeatable inspection results; order directly via Metav Werkzeuge or contact the consultants for application advice and availability. Gauge pin M323.J43 – single precision pin, Ø 19.43 mm, 50 mm length (Metav IndustryLine) The Gauge pin M323.J43 is a workshop-grade, single reference pin designed for end‑mass checks and go/no‑go verification in production and quality control environments. Precision diameter Ø 19.43 mm High repeatability ±0.002 mm 50 mm length for stable seating Workshop-grade finish, durable Reliable reference for repeatable checks A compact reference component engineered for consistent measurements, the pin provides a clear metrological baseline for bore and pass/fail checks. Thanks to the ±0.002 mm specification and the precisely machined Ø 19.43 mm dimension, the component supports high repeatability in repetitive inspection tasks. The combination of exact geometry and a stable 50 mm shank reduces positional variation during seating, which helps to lower measurement uncertainty and improves traceability in routine checks. Improves inspection throughput and process security Using a dedicated reference pin speeds up verification steps and reduces setup time at test stations. The hardwearing construction in special steel and the compact single‑piece design permit fast insertion and withdrawal, helping inspection cycles to run smoothly with minimal downtime. As a rational choice for production lines and small inspection benches, this pin contributes to fewer false rejects and a more predictable quality flow, supporting efficient process control and higher first‑pass yield. Built for workshop use and simple integration The workshop-grade finish makes the component robust against everyday handling while remaining suitable for precision fixtures. At a modest weight of 0.2 kg and a clear 50 mm length, it integrates easily into gauge blocks, fixture assemblies and handheld checking tools without requiring special adapters. The item is supplied as an individual reference pin and is identifiable by SKU M323.J43, which simplifies stock management and reorder processes for maintenance and calibration departments. Contact Metav Werkzeuge for a technical consultation and rapid supply from Emmerich—quote SKU M323.J43 for a workshop-ready precision pin tailored to end-mass checks Technical data SKU: M323.J43 GTIN: 4061905449963 Designation: Gauge pin, single, Ø 19.43 mm, length 50 mm Brand: Metav IndustryLine Facts Diameter: 19.43 mm Length: 50 mm Accuracy / tolerance: ±0.002 mm Weight: 0.2 kg Special features Material: Special steel Version: Workshop‑grade execution Single reference pin for end‑mass and go/no‑go checks Suitable for use in fixtures and gauge assemblies FAQ What is the dimensional tolerance of the pin? The pin is specified with an accuracy of ±0.002 mm, giving reliable repeatability for precision checks with the gauge pin M323.J43. Which material is the pin made from? The component is manufactured from special steel and finished for workshop use to combine durability with the dimensional stability required for reference measurements. How is this pin typically used in inspection? As a single reference pin, it serves for end‑mass verification, bore gauging and pass/fail fixtures; the 50 mm length and precise Ø 19.43 mm diameter make it suitable for stable seating in test rigs. How is the item identified for reordering or stock control? The product is stocked under SKU M323.J43 and GTIN 4061905449963, allowing straightforward identification and replenishment. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
19.44mm Test Pin 50mm Length Workshop Version - Metav IndustryLine
Benefit from high‑precision control thanks to the combination of ±0.002 mm tolerance, special steel construction and a compact 50 mm length that speeds up end‑measure verification. Order the gauge pin directly via Metav Werkzeuge or consult our specialists for application advice. Gauge pin M323.J44 — single 19.44 mm Ø, 50 mm length (Metav IndustryLine) The gauge pin M323.J44 is a workshop‑grade end‑measure pin designed for fast dimensional checks, fixture set‑up and routine inspection in production and maintenance environments Workshop‑grade design Diameter 19.44 mm precision ±0.002 Length 50 mm for end‑measure checks Made from special steel Precision that reduces inspection uncertainty The compact gauge pin provides a guaranteed tolerance of ±0.002 mm, an accuracy level that supports fine inspection tasks and reproducible go/no‑go checks. At this tolerance, deviations are kept within micrometre‑range limits, which is critical when verifying bore diameters, aligning fixtures or performing tight‑tolerance assembly work. The nominal 19.44 mm diameter serves as a stable reference for quick pass/fail decisions and reduces cumulative measurement error across repeated checks. Robust workshop construction for everyday use Manufactured from special steel, the single‑piece design emphasises wear resistance and dimensional stability under shop conditions. The 50 mm length gives secure handling and easy insertion into bores or jig seats while remaining compact enough for handheld use. The solid build minimises bending and surface wear during repeated contact, so calibration intervals are extended and downtime for replacements is reduced. The workshop execution balances toughness with the precision required for routine quality control tasks. Streamlined inspection routines and traceability The single‑pin format simplifies inventory and inspection workflows: one compact tool for fast end‑measure verification, fixture alignment and spot checks on production lines. Identified as M323.J44, this gauge pin integrates into sampling plans to accelerate throughput and supports consistent pass/fail criteria. Supply from Metav IndustryLine ensures dependable availability and clear product traceability, which helps maintain steady inspection cycles and reduces the risk of production delays. Contact Metav Werkzeuge for delivery from Emmerich and expert guidance on integrating the M323.J44 gauge pin into inspection routines Technical Data Article number: M323.J44 GTIN: 4061905449987 Net weight: 0.2 kg Material: Special steel Core data Diameter: 19.44 mm Length: 50 mm Tolerance: ±0.002 mm Special features Workshop version Intended use: end measurements ECLASS: 21170231 SKU: M323.J44 FAQ What tolerance does this gauge pin provide? The gauge pin delivers a tolerance of ±0.002 mm; the M323.J44 (Metav IndustryLine gauge pin) is therefore suitable for precise end‑measure checks. Which applications suit this single gauge pin? This single pin is intended for end‑measure verification, fixture alignment and quick go/no‑go inspections in workshop and production environments using the M323.J44 format. What material is the pin made from? The pin is made from special steel, chosen for wear resistance and dimensional stability under regular workshop use. How does this gauge pin support inspection efficiency? The compact, single‑piece format simplifies handling and speeds up routine checks; M323.J44 helps reduce inspection time and maintain consistent sampling criteria. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
19.45mm Gauge Pin 50mm Length Workshop Version - Metav IndustryLine
Take advantage of precision (±0.002 mm) and a compact Ø 19.45 mm × 50 mm form for reliable end‑dimension checks in the workshop; the workshop‑grade gauge pin is robust, simple to handle and supplied ready for transport. Order the gauge pin directly via Metav Werkzeuge or consult our specialists for application advice. Metav IndustryLine Gauge Pin M323.J45 — Ø 19.45 mm, 50 mm length The Gauge pin, single, 19.45 mm, length 50 mm is a workshop‑grade reference pin for end‑dimension verification and fixture set‑up in production and inspection environments. Workshop‑grade construction Diameter tolerance ±0.002 mm Length 50 mm for stable handling Supplied in protective transport case Precision that reduces rework and speeds inspection The gauge pin delivers a clearly defined reference with a diameter of 19.45 mm and a tight tolerance of ±0.002 mm, which translates into repeatable go/no‑go checks and consistent fixture setting. In practice this level of accuracy reduces measurement uncertainty and the need for rework, so inspection cycles become faster and more predictable. The compact geometry and defined contact area mean that bench or jig checks can be completed without complex set‑ups, contributing directly to throughput improvements on the shop floor. Built for workshop handling and steady positioning Designed as a workshop‑grade tool, the pin’s 50 mm length offers a favourable balance between handling stability and accessibility in confined setups. The component’s moderate mass assists in steady positioning during checks without requiring elaborate clamping, which shortens handling time. The item is manufactured from special steel for durability under frequent use; its finish and dimensional stability support repeated insertion and withdrawal in fixture holes and bore checks typical of mid‑volume production environments. Traceability and practical integration into routines The single gauge pin provides a straightforward physical reference for dimensional checks, simple to incorporate into inspection routines or to use as a master for quick alignments. With a distinct article identity (M323.J45, GTIN provided below) the part is easy to document in inspection logs and inventory systems. Supplied in a protective transport case, it arrives protected against handling damage during storage and transit, which preserves the pin’s dimensional integrity until use. For workshop‑grade measurement reliability, contact Metav Werkzeuge to discuss the M323.J45 gauge pin and its application in inspection or fixture workflows Technical data Article number: M323.J45 GTIN: 4061905072062 Brand: Metav IndustryLine Facts Diameter: 19.45 mm Length: 50 mm Tolerance: ±0.002 mm Weight: 0.2 kg Label: Prüfstift, einzeln, 19,45 mm Länge 50 mm Special features Material: Special steel Workshop execution Supplied in protective transport case ECLASS: 21170231 FAQ What tolerance does the gauge pin offer? The M323.J45 gauge pin (Metav IndustryLine) is specified with a diameter tolerance of ±0.002 mm. Is this pin suitable for fixture setting and alignment? Yes, the 50 mm length and workshop‑grade design of this gauge pin make it well suited for fixture set‑up, alignment and repeatable reference checks. Is a calibration certificate supplied with the gauge pin? The product information for the M323.J45 does not indicate an included calibration certificate; calibration status should be confirmed if a traceable certificate is required. What material is the pin made from and how does that affect durability? The gauge pin is made from special steel, chosen for wear resistance in frequent workshop use and for maintaining dimensional stability under normal inspection conditions. How is the gauge pin packaged for delivery? The M323.J45 is supplied in a protective transport case to prevent handling damage during storage and transit. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
19.46mm Gauge Pin, Single, 50mm Length Workshop Version - Metav IndustryLine
Consistent shop-floor results through high reproducibility and robust construction: ±0.002 mm tolerance and a 19.46 mm diameter deliver repeatable end‑size checks, while the compact 50 mm length supports stable positioning in fixtures. Order the gauge pin directly via Metav Werkzeuge or ask our consultants if needed. Gauge pin M323.J46 — 19.46 mm diameter, 50 mm length (Metav IndustryLine) The Gauge pin M323.J46 is a single, precision test pin designed for dimensional reference and fixture alignment in workshop and inspection environments. Precision tolerance ±0.002 mm Diameter 19.46 mm for end‑size checks 50 mm length for stable positioning Workshop version for robust handling Keep production tolerances under control with measurable precision A tight tolerance of ±0.002 mm makes this test pin suitable where reproducible fits and minimal rework are essential. The specified tolerance indicates that the part can be used as a dimensional reference in routine checks and assembly preparations, reducing the need for repeated adjustments. By converting a manufacturing requirement into a measurable standard, the pin supports faster quality decisions and a steady production flow while improving traceability of inspection steps. Robust construction for everyday workshop use Manufactured from special steel, the component is built for frequent handling on the shop floor. The compact 50 mm length provides a stable seating in fixtures and gauges without excess overhang, reducing the risk of bending or misalignment during use. The workshop version designation highlights pragmatic design choices that favour durability and easy integration into jigs and holding devices, helping to maintain consistent contact conditions during repetitive measurements. Practical integration into inspection and assembly processes As a single gauge pin, this item suits end‑size checks, fixture alignment and dimensional referencing tasks where a precise cylindrical datum is required. Identification is straightforward thanks to the clear article code and GTIN, aiding stock management and process documentation. When used as a reference element in fixture set‑up, the pin contributes to repeatable results across multiple operators and shifts, thereby enhancing process reliability and reducing the incidence of scrap. Contact Metav Werkzeuge today for tailored advice on the M323.J46 gauge pin and to discuss how the Metav IndustryLine range can streamline inspection routines — Metav Werkzeuge GmbH is based in Emmerich and reachable at +49 2822 7131930 or info@metav-werkzeuge.com Technical data Article number: M323.J46 GTIN: 4061905072079 Label: Prüfstift, einzeln, 19,46 mm Länge 50 mm Manufacturer: Metav IndustryLine Core specifications Diameter: 19.46 mm Length: 50 mm Tolerance: ±0.002 mm Weight: 0.2 kg Materials & special features Material: Special steel Design: Workshop version Application: End‑size checks and fixture alignment FAQ What is the declared tolerance of the gauge pin? The M323.J46 gauge pin is specified with a tolerance of ±0.002 mm, suitable for repeatable dimensional references in inspection work. Which material is used for the test pin? The test pin is made from special steel, chosen for wear resistance and durability in workshop conditions. What are the typical applications for this gauge pin? Typical uses include end‑size checks, fixture alignment and serving as a cylindrical datum during assembly and inspection. How can the part be identified in stock systems? Identification is possible via the SKU M323.J46 and GTIN 4061905072079, which support catalogue and inventory tracking. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
Fast, tactile checks where electronics are impractical
Gauges and test pins provide unequivocal go/no-go results for threads, bores, gaps and radii without relying on electronics. The range covers plug gauges and ring gauges for internal and external threads, feeler gauges and precision feeler strips for micro‑gap assessment, plus probe pins and measuring pins for tactile diameter and pitch checks.
How these tools work in the production environment
Mechanical gauges operate as direct reference standards: a plug gauge or ring gauge verifies conformity to thread profiles and mating ability, while limit gauges separate accept from reject in a single step. Test pins are used to tactilely measure small bore diameters, centre‑to‑centre distances and radii. Manufactured from hardened gauge steel or ceramic and often precision lapped, these instruments deliver immediate physical results that are ideal for incoming inspection, machine‑side checks and final control.
Measurable benefits that affect production performance
- Reduced scrap and rework through rapid, unambiguous pass/fail assessment.
- Increased repeatability thanks to very low measurement uncertainty and fine lapping.
- Lower downtime: quick checks at the machine save cycle time and reduce setup periods.
- Durable construction with high wear resistance from specialised, low‑distortion alloys.
- Versatile delivery formats: individual gauges, organised sets in wooden cases or metre‑length feeler rolls compliant with DIN 2269.
Why Metav is the practical choice for precision supplies
Metav combines decades of expertise with a broad warehouse and quality filtering from Emmerich. As a precision partner for industry, craft and trade, Metav supplies a comprehensive selection of gauges and test pins alongside complementary tools such as precision calipers and setting rings. With over 48,000 customers and a catalogue exceeding 250,000 items, Metav is positioned to supply reliably, reduce vendor complexity and support traceable quality control to national standards.
Summary
Gauges and test pins are indispensable for dependable, repeatable quality assurance where tactile, mechanical verification is preferred. Choose these plug gauges, ring gauges, feeler strips and probe pins when immediate, robust measurement decisions are required on the shop floor.
FAQ
What materials are gauges and test pins typically made from?
Gauges and test pins are usually manufactured from hardened gauge steel for durability and wear resistance; ceramic variants are available where thermal stability and minimal wear are critical.
How do thread gauges ensure mating capability?
Thread plug gauges and ring gauges check flank diameters and thread form against standards, providing a clear go/no‑go verdict that confirms pairability with mating parts.
Which tolerance class should I choose for probe pins and gauge sets?
Select tolerance classes aligned with your inspection requirements; for high‑precision tasks, sets produced to DIN 2269 or equivalent tolerance classes ensure micrometre‑level control and repeatability.
Can feeler gauges measure contact gaps in valve and engine work reliably?
Yes. Feeler gauges and precision feeler strips, supplied either as a fan or metre‑length rolls, allow accurate assessment of valve clearances and contact gaps down to micrometre increments.
How do limit gauges speed up in‑process inspection?
Limit gauges separate good from bad in a single, tactile operation, enabling rapid go/no‑go checks at the machine and reducing both inspection time and the likelihood of human interpretation errors.
Fragen zu diesen Produkten??
Mit mehr als 30 Jahren Erfahrung beraten wir Sie gerne persönlich.
Tel.: +49 2822 7131930
Mail: info@metav-werkzeuge.com