Precision gauge blocks and plug gauges for reliable dimensional control
Mechanical gauge blocks and plug gauges are essential for tactile verification of threads, bores and gap dimensions, providing fast, unambiguous go/no-go results that enhance process reliability and reduce scrap. Designed for industrial metalworking and toolmaking, these precision tools support incoming inspection and final quality checks by delivering traceable measurements in applications such as thread inspection, bore diameter testing and spacing checks. Manufactured from specially hardened, low-distortion alloys and fine-lapped for minimal measurement uncertainty, the range includes thread plug gauges, precision plug gauges and calibration gauge blocks to ensure long-term repeatability and wear resistance.
19 mm Gauge Pin, Single, 50 mm Length, Workshop Version - Metav IndustryLine
Take advantage of the combination of 19.00 mm nominal diameter, ±0.002 mm tolerance and a compact 50 mm length for reliable plug and bore checks in workshop environments; order the gauge pin via Metav Werkzeuge or contact our consultants for application advice. Gauge pin, single, 19.00 mm — Metav IndustryLine gauge pin, 50 mm length, high-precision fit A gauge pin designed for workshop inspection and end‑measure tasks, offering a precise reference diameter for repeatable bore and fit verification. 19.00 mm calibrated diameter Length 50 mm workshop version Tolerance ±0.002 mm high precision Supplied in a protective transport case Consistent radial accuracy for fit and inspection The core advantage of this precision pin is its ±0.002 mm tolerance, which provides a dependable reference for go/no‑go checks and clearance measurements. In practice, this level of accuracy reduces uncertainty when verifying bore diameters, alignment pins and mating fits. The nominal diameter of 19.00 mm is produced to tight dimensional control, ensuring the pin can be used as a repeatable standard across inspection benches and assembly jigs. This rational benefit shortens troubleshooting cycles and supports quality gates in production workflows. Workshop durability with compact handling benefits Manufactured from special steel, the pin combines the rigidity required for reproducible results with a size that is easy to handle on the shop floor. The compact 50 mm length minimises flex during insertion and withdrawal, improving the repeatability of checks on short bores or stepped holes. The workshop configuration is aimed at daily use: it is robust enough for repeated handling yet compact enough for quick bench testing, supporting efficient inspection routines in metalworking and mechanical assembly. Practical integration into inspection routines Designed as a single‑piece reference, this precision pin simplifies measurement sequences and fixture set‑up. It serves as a tactile and visual reference for alignment, depth checks and plug‑gauge operations, making it suitable for assembly stations and quality control benches. The delivery in a protective case preserves the calibrated surface during transport and storage, reducing the risk of accidental damage and keeping the 19.00 mm diameter within specified tolerance for longer intervals between rework or replacement. For workshop-grade precision from Metav IndustryLine, request a technical consultation or a quotation from Metav Werkzeuge in Emmerich – info@metav-werkzeuge.com / +49 2822 7131930 Technical data Article number: M323.J00 GTIN: 4061905072147 ECLASS: 21170231 Facts Nominal diameter: 19.00 mm Length: 50 mm Tolerance: ±0.002 mm Weight: 0.2 kg Special features Material: special steel Workshop design Supplied in protective transport case Category: Gauge pins (Messstifte) FAQ What applications is this gauge pin suitable for? The gauge pin is suitable for plug and bore checks, alignment tasks and use as a reference in inspection and assembly processes; Metav IndustryLine gauge pin M323.J00 is intended for workshop inspection work. How precise is the diameter of the pin? The diameter is manufactured to a tolerance of ±0.002 mm, giving the pin the repeatability expected for precise fit verification with Metav IndustryLine gauge pins. What material is the pin made from and why does it matter? This pin is made from special steel, which provides the rigidity and surface quality required for consistent measurement results during routine workshop use. Is the pin supplied ready for transport and storage? The product is supplied in a protective transport case to preserve the measurement surface and minimise handling damage during storage and transit. Can this gauge pin be used for calibration reference? The pin offers a stable dimensional reference for internal checks and fixture set‑up; for formal calibration services or certificates, please enquire with Metav Werkzeuge about available options for traceable calibration. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
19 mm Limit Plug Gauge, Wear Allowance On Good Side, Hardened Steel, DIN 7162 - Filetta
Take advantage of a standards‑based inspection tool that pairs hardened steel construction with DIN 7162 conformity and a practical wear allowance on the go side, ensuring reliable pass/fail checks and prolonged service life; order the gauge directly via Metav Werkzeuge or consult our team for application advice. Filetta Limit Plug Gauge G7 – 19 mm, hardened steel (DIN 7162) A Filetta Limit Plug Gauge G7 designed for fast go/no-go verification of 19 mm bores in line with DIN 7162 for consistent production control Hardened steel construction Conforms to DIN 7162 19 mm nominal diameter Wear allowance on the go side Rapid, standards‑compliant inspection that saves time A purpose‑built limit plug gauge provides an immediate quality decision: go/no-go assessment without the need for complex readouts. Conformity with DIN 7162 guarantees the gauge’s dimensions and tolerances match recognised inspection criteria, which accelerates in‑process checks and reduces bottlenecks on the production line. The 19 mm nominal diameter is specified for direct matching to mating bores; using a dedicated gauge for this diameter simplifies sampling plans and shortens cycle time while maintaining clear, auditable acceptance criteria. Robust construction for lasting accuracy Made from hardened steel, the gauge resists wear and maintains geometry across repeated use, which sustains repeatability of results. The design includes a wear allowance on the go side, a planned material margin that can be used to extend the service life before the gauge reaches its limit condition. In practical terms, the wear allowance postpones replacement, lowers lifetime cost, and preserves measurement integrity—critical when inspections are frequent or when a single gauge serves multiple machines or workstations. Easy integration into shop‑floor routines and quality systems The compact, single‑purpose format of this limit plug gauge suits assembly lines, quality control benches and manual inspection jigs. Implementation requires minimal training: the visual or tactile pass/fail outcome reduces interpretation time compared with continuous measuring instruments. For organisations aiming to standardise inspection methods, the gauge fits into existing metrological workflows and documentation. Metav’s position as a precision partner supports straightforward procurement and reliable supply from Emmerich, backed by decades of distribution experience for industrial metrology. Contact Metav Werkzeuge today to confirm suitability and request delivery of the Filetta Limit Plug Gauge G7 (SKU MS911.181); Metav’s advisors in Emmerich will provide practical guidance and rapid fulfilment Technical data Article number: MS911.181 Manufacturer: Filetta Designation: Limit plug gauge G7 Facts Nominal diameter: 19 mm Standard: DIN 7162 Special features Material: hardened steel Wear allowance on the go side Category: gauges / plug gauges / inspection pins FAQ What inspection task is this gauge intended for? The Filetta Limit Plug Gauge G7 (SKU MS911.181) is intended for quick go/no-go verification of 19 mm internal bore dimensions to support routine pass/fail inspection. Which standard does the gauge comply with? This limit plug gauge is manufactured to conform with DIN 7162, ensuring dimensional and tolerance compatibility for standardised checks. How does the wear allowance affect service life? The wear allowance on the go side provides an engineered margin that prolongs usable life by allowing controlled wear before the gauge reaches its limit condition. What material is the gauge made from and why does that matter? The gauge is made from hardened steel, which maintains geometry under repeated use and supports long‑term repeatability of inspection results. Can this gauge be used in automated inspection fixtures? Yes, the solid construction and single‑function geometry of this plug gauge make it suitable for integration into manual and automated fixtures where a 19 mm go/no-go check is required. Manufacturer / Responsible: Schut Geometrische Meettechniek bv; Duinkerkenstraat 21; 9723 BN Groningen; The Netherlands; +31 50 5877877; schutnl@schut.com
19 mm Setting Ring Form C, Hardened Gauge Steel, DIN 2250/DIN 286 JS3 - Metav IndustryLine
Take advantage of a compact, standards‑compliant ring gauge that combines a 19 mm nominal diameter, hardened and lapped gauge steel and the proven tolerance class JS 3 to ensure repeatable set‑ups and reliable fit checks. Order the M313.019 setting ring directly via Metav Werkzeuge or consult our advisers for application support. M313.019 setting ring gauge — 19 mm, DIN 2250, hardened gauge steel (Metav IndustryLine) M313.019 setting ring gauge for precision ring setting and acceptance testing in workshop and quality environments Hardened and lapped gauge steel Conforms to DIN 2250 and DIN 286 Tolerance class JS 3 for close fits Form C geometry for standard applications Repeatable set‑ups that reduce rework and downtime Manufactured from hardened and lapped gauge steel, the ring offers a stable measuring surface that resists wear and keeps the nominal diameter consistent over many cycles. The combination of a fine surface finish and robust material means the gauge maintains its shape under normal workshop handling, which directly contributes to faster, more reliable set‑ups on machines and gauges. Using a dedicated ring gauge for external checks removes uncertainty from go/no‑go decisions and helps maintain process stability over time. Certified geometry for confident conformity checks Designed to the specifications of DIN 2250 and DIN 286, with tolerance class JS 3, this gauge provides a clear reference for production and inspection tasks where repeatability matters. The standardised form and tolerance ensure that measurements are directly comparable across shifts and suppliers, simplifying acceptance protocols and reducing dispute potential. For operations that require strict interchangeability and documented compliance, the recognised standards are a decisive advantage. Practical design for workshop use and handling The Form C configuration gives a practical balance between accessibility and handling convenience for ring gauges in this size range. The compact nominal diameter simplifies storage and placement during batch checks while the lapped finish eases cleaning and reduces the risk of false indications caused by debris. Built with industrial workflows in mind, the gauge supports efficient inspection routines without adding procedural complexity. Contact Metav Werkzeuge for a supply recommendation of the Metav IndustryLine setting ring — our consultants will advise on suitability for the intended application and delivery options Technical data Article number: M313.019 GTIN: 4054469120577 ECLASS: 21170104 Category: Gauges (Lehren) Key figures Nominal diameter: 19 mm Customs tariff number: 90173000 Special features Material: hardened and lapped gauge steel Standards: DIN 2250, DIN 286 Tolerance class: JS 3 Form: C FAQ What applications suit this type of ring gauge? The M313.019 setting ring gauge is intended for precise fit verification and ring setting in production, assembly and inspection tasks where a 19 mm nominal diameter and JS 3 tolerance are appropriate. Is the material suitable for long‑term workshop use? Yes; the hardened and lapped gauge steel used for this gauge gives a wear‑resistant surface that supports repeated use in a workshop environment while preserving dimensional stability. How does the gauge relate to international standards? This ring gauge is manufactured to DIN 2250 and DIN 286 specifications, providing standardised geometry and tolerances that facilitate consistent conformity checks across suppliers and inspection systems. Can the M313.019 setting ring gauge be used for go/no‑go testing? The gauge’s defined JS 3 tolerance and standardised form make it suitable as a reference for go/no‑go assessments and for establishing repeatable set‑up conditions in production. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
19.01mm Gauge Pin 50mm Length Workshop Version - Metav IndustryLine
Taking advantage of Ø 19.01 mm nominal size, ±0.002 mm tolerance and a compact 50 mm length ensures reliable end‑dimension checks with minimal handling time; order the gauge pin directly via Metav Werkzeuge or consult the team for set configurations and transport options. Metav IndustryLine Gauge Pin – Ø 19.01 mm, 50 mm length The Metav IndustryLine gauge pin is a single precision inspection pin designed for fast end‑dimension verification and repeatable reference measurements in workshop and inspection environments. Ø 19.01 mm precision pin Length 50 mm for deeper bores Tight tolerance ±0.002 mm Workshop version with transport case Keeps production checks fast and verifiable A compact inspection pin with a nominal diameter of 19.01 mm and a tolerance of ±0.002 mm supports rapid go/no‑go checks and reference measurements directly at the machine or inspection bench. The tight tolerance reduces ambiguity in pass/fail decisions, helping to cut down rework and downtime. Using a hard, dimensionally stable pin instead of improvised gauges shortens set‑up times and creates a clear audit trail for quality documentation, which benefits throughput and traceability in serial production. Built for workshop handling and repeatability The 50 mm shank length combines accessibility for deeper features with a controllable handling envelope that minimises bending and measurement error. Constructed from special steel, the pin resists wear during frequent engagement with mating bores and permits repeated use without rapid diameter change. Delivered in a transport case, the component arrives protected for immediate use on shop floors and is easy to store alongside other inspection tools, preserving the calibrated condition and surface integrity over time. Practical applications and compatibility with existing workflows This precision pin serves as an end‑dimension reference for assembly checks, jig and fixture set‑up, and go/no‑go testing in metalworking and mechanical workshops. The design is compatible with standard pin‑type holders and bench fixtures, making it straightforward to integrate with existing gauging routines. Because the component is a single‑piece inspection device, it is particularly useful where a simple, unambiguous reference diameter is required for passing parts between production stages or for first‑off inspections. Handling, maintenance and procurement guidance Lightweight at approximately 0.2 kg, the pin is easy to handle and transport between workstations. Routine care involves keeping the contact surfaces clean and free from burrs; gentle wiping and storage in the supplied transport case will extend service life and maintain measurement confidence. For batch use, matching sets or serially numbered pins can be requested to ensure consistent interchangeability across multiple machines. Metav’s catalogue contains complementary inspection accessories to create complete, ready‑to‑use test kits. For workshop‑grade, immediately usable precision, request the Metav IndustryLine gauge pin from Metav Werkzeuge and ask our consultants about matching sets, protective cases and delivery options. Technical data Article number: M323.J01 GTIN: 4061905072154 Category: Messstifte SKU: M323.J01 Facts Diameter: 19.01 mm Length: 50 mm Tolerance: ±0.002 mm Weight: 0.2 kg Special features Material: Special steel Workshop execution Delivered in transport case Precision class: ±0.002 mm FAQ What is the measurement tolerance of this gauge pin? The Metav IndustryLine gauge pin (M323.J01) is manufactured and verified to a tolerance of ±0.002 mm for reliable pass/fail and reference checks. Can this pin be used for deeper bore inspections? Yes, the 50 mm shank length is suitable for deeper bores where a short reference pin would not reach, while still offering good stiffness for repeatable checks. What material is the pin made from and how does that affect wear? The pin is made from special steel, chosen for dimensional stability and wear resistance so it maintains diameter integrity during repeated use. Is the gauge pin delivered ready for use in a workshop environment? The item is supplied as a workshop version and is delivered in a transport case, protected for immediate deployment at the bench or machine. Are matching pins or sets available to ensure interchangeability? Metav supplies matching inspection components and sets; consult Metav Werkzeuge for options to maintain interchangeability across multiple stations. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
19.02mm Gauge Pin 50mm Length Workshop Version, Special Steel - Metav IndustryLine
A high‑precision gauge pin offering a 19.02 mm diameter with a tight ±0.002 mm tolerance and a 50 mm overall length supports reliable go/no‑go verification and reduces rework in serial production; order the gauge pin directly via Metav Werkzeuge or contact our consultants for application advice. Gauge pin, 19.02 mm diameter, length 50 mm — Metav IndustryLine workshop version A gauge pin precision ground to 19.02 mm diameter and 50 mm length, designed for fast end‑measure checks and insertion tests in workshop and inspection environments Precision diameter 19.02 mm, tolerance ±0.002 Length 50 mm, precision ground Special steel for workshop durability Single‑piece supply, workshop execution Reduce rejects with reproducible fit checks A narrowly toleranced plug ensures reproducible results during routine inspections. The ±0.002 mm tolerance gives a measurable boundary between acceptable and non‑conforming bores, meaning fewer false rejects and less rework. Used as a reference pin in assembly jigs or bench checks, this component converts dimensional specifications into a simple mechanical test: a secure fit indicates conformity, a refusal signals intervention. The clear, quantifiable tolerance also simplifies documentation for quality records and process audits, supporting traceable decisions on the shop floor. Built for everyday workshop reliability Manufactured from special steel and finished by precision grinding, the pin combines surface integrity with dimensional stability across repeated use. The 50 mm length provides sufficient engagement for most bore checks while remaining easy to handle and store. The workshop execution reflects resistance to handling and routine abrasion typical in production environments; users gain a durable tool that maintains precision over many cycles, reducing mean time between replacements and supporting steady production throughput. Seamless integration into quality procedures Compact and single‑piece, the pin slots into existing inspection routines, gauge blocks, or fixture pockets without complex adapters. Marking and traceability are facilitated via the SKU, enabling inventory control and repeat ordering. The practical design expedites go/no‑go checks, helping to keep throughput steady and inspection time to a minimum. Backed by Metav’s emphasis on accessible precision, this component supports consistent measurement practice across workshop and machine‑shop contexts, contributing to operational reliability and confident delivery to customers. For robust fit verification choose the Metav IndustryLine gauge pin M323.J02 — contact Metav Werkzeuge for availability and technical advice at info@metav-werkzeuge.com or call +49 2822 7131930 Technical Data Article number: M323.J02 GTIN: 4061905072161 Brand: Metav IndustryLine Type: Gauge pin, single Facts Diameter: 19.02 mm Length: 50 mm Tolerance: ±0.002 mm Weight: 0.2 kg Special features Material: special steel Workshop execution Precision ground Single‑piece supply SKU: M323.J02 FAQ What are the exact dimensions and tolerance of this pin? The gauge pin has a diameter of 19.02 mm and a tolerance of ±0.002 mm; this specification applies to the Metav IndustryLine gauge pin M323.J02. Which material is used for the pin? The pin is made from special steel, selected for wear resistance and dimensional stability in workshop use. Is the pin supplied individually or as part of a set? The item is supplied as a single piece in the workshop execution format. For which applications is this pin suitable? It is suitable for go/no‑go checks, insertion tests, fixture indexing and general bore verification in production and inspection tasks. How should the pin be stored and maintained? Store the pin clean and dry; avoid contact with corrosive environments and wipe with an anti‑corrosion cloth if required to preserve surface quality. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
19.03mm Gauge Pin 50mm Length Workshop Version - Metav IndustryLine
Take advantage of a workshop‑grade inspection pin with Ø 19.03 mm diameter, 50 mm length and a tight ±0.002 mm tolerance for reliable end‑measure verification; delivered in a protective case. Order the gauge pin directly via Metav Werkzeuge or ask our consultants if needed. Gauge pin M323.J03 — Inspection pin, Ø 19.03 mm, 50 mm length (Metav IndustryLine) The gauge pin M323.J03 is a workshop‑grade inspection pin designed for precise end‑dimension checks and bore verification in routine metrological control. Workshop‑grade finish, robust design Diameter 19.03 mm for tight fits Tolerance ±0.002 mm for precise checks Delivered in protective case for transport Precision for critical fits and reproducible checks For demanding fit and clearance checks the 19.03 mm diameter provides a defined reference geometry that reduces measurement uncertainty. With a specified ±0.002 mm tolerance the inspection pin targets tasks where dimensional fidelity matters, such as final inspection of mating parts or verification of gauges. The marked accuracy supports consistent pass/fail decisions in quality control and shortens inspection times thanks to fewer repeat measurements. This focus on measurable performance underpins efficient fault isolation and reduces rework in production processes. Robust workshop design for everyday handling Constructed from special steel, the pin is engineered for durability in standard workshop environments. The 50 mm length provides sufficient engagement for most end‑measure and bore checks while remaining easy to handle and manoeuvre. The workshop‑grade finish balances surface robustness and dimensional stability, so the reference surface resists routine wear. Supplied in a protective case, the pin is ready for safe transport and storage, preserving calibration and reducing the risk of damage between uses. Practical application and integration in inspection routines As a dedicated inspection tool, this gauge pin suits workshop metrology tasks such as end‑dimension verification, checking drilled bores and secondary inspection steps in assembly. The compact format and repeatable dimensions make it suitable for use in go/no‑go checks alongside plug gauges or as a reference for visual and tactile confirmation. Where traceability and clear identification are required, the product is listed under SKU M323.J03 and integrates into documented inspection workflows, helping to maintain traceable records and consistent quality across batches using Metav IndustryLine components. For dependable metrology with a workshop‑grade inspection pin from Metav IndustryLine, contact Metav Werkzeuge for purchase guidance and technical advice by eMail at info@metav-werkzeuge.com or by phone at +49 2822 7131930 — professional support is available from the Emmerich quality centre. Technical data Article number: M323.J03 GTIN: 4061905072178 Category: Gauge pins Facts Diameter: 19.03 mm Length: 50 mm Tolerance: ±0.002 mm Weight: 0.2 kg Special features Material: special steel Workshop version Delivered in protective case for transport SKU: M323.J03 FAQ What is the primary use of this gauge pin? The gauge pin M323.J03 is intended for end‑dimension checks and bore verification as part of routine workshop inspection procedures. How precise is the inspection pin for quality control? Precision is specified as ±0.002 mm, making the pin suitable for tight tolerance checks and reproducible measurement comparisons. What material is the pin made from and how does that affect use? Made from special steel, the pin combines dimensional stability with a durable surface suitable for regular workshop handling. Is the pin supplied ready for transport and storage? Yes, the inspection pin is delivered in a protective case to safeguard the reference surface during transport and storage. Can this gauge pin be used with existing plug gauge sets? The geometry and tolerance of the pin make it compatible for use alongside plug gauge routines and as a reference in combined inspection setups. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
19.04mm Gauge Pin, Single, 50mm Length, Workshop Version - Metav IndustryLine
Precision gauging for consistent workshop inspection: a hardened special steel construction with ±0.002 mm tolerance and a compact 50 mm length delivers repeatable end‑measurement results; order the gauge pin directly via Metav Werkzeuge or ask our consultants if needed. Gauge pin M323.J04 — Ø 19.04 mm, 50 mm length (Metav IndustryLine) The gauge pin M323.J04 is a workshop‑grade measuring pin for fast dimensional checks, fixture setting and end‑size verification in machining and inspection tasks Workshop‑grade design for routine metrology Diameter precisely 19.04 mm Length 50 mm for compact setups Tolerance ±0.002 mm for tight control Accuracy that reduces rework and rejects Engineered for strict dimensional control, this measuring pin combines a nominal diameter of 19.04 mm with a verified ±0.002 mm tolerance to minimise sorting and rework in serial inspection. The fine tolerance is particularly valuable when small deviations cascade into assembly failures; employing a hardened special steel pin for go/no‑go verification or plug checks helps keep production tolerances consistent and traceable. The compact design also enables rapid repeat measurements in confined fixtures without compromise to stability. Designed for workshop efficiency and durability The compact 50 mm length and robust workshop execution offer an excellent balance between handling and stiffness for everyday use at the bench. At around 0.2 kg, the pin is easy to position yet substantial enough to avoid inadvertent movement during setting or checking. Delivery includes a transport box, protecting the gauge during storage and transit and reducing setup time between jobs. This combination of durable material and practical packaging supports efficient workflows and lowers downtime. Fit for inspection routines and supply chain traceability The M323.J04 is suited to fixture setting, end‑dimension verification and routine plug gauge checks, where repeatable contact geometry is required. Traceable identifiers such as SKU M323.J04 and GTIN support inventory and quality processes, while the workshop specification ensures consistency across shifts and operators. Supplied by Metav, a precision partner with a strong European quality filter and wide product range, the pin helps integrate reliable gauging into everyday production and inspection routines. For workshop‑level accuracy and fast delivery from Emmerich, contact Metav Werkzeuge to discuss the M323.J04, request application advice or arrange supply via info@metav-werkzeuge.com or +49 2822 7131930 Technical data SKU: M323.J04 GTIN: 4061905072185 eClass: 21170231 Facts Diameter: 19.04 mm Length: 50 mm Tolerance: ±0.002 mm Weight: 0.2 kg Special features Material: special steel Workshop execution Delivered in transport box FAQ What applications are suitable for this gauge pin? Typical uses include end‑dimension verification, fixture setting, go/no‑go checks and plug gauge routines where a nominal diameter of 19.04 mm is required; the M323.J04 is specified for routine workshop metrology jobs. Is the pin corrosion resistant or surface treated? The pin is manufactured from special steel; the product specification does not list an additional coating, so surface protection should be considered separately if working in corrosive environments. Can this pin be used for precision assembly alignment? Yes, the tight tolerance of ±0.002 mm and the stable 50 mm length make it suitable for assembly alignment and repeatable positioning in jigs and fixtures. How is the gauge delivered and protected? Delivery includes a transport box to protect the pin during storage and shipment, ensuring the contact surfaces remain intact until use. Are identification numbers provided for inventory control? Yes; the item is supplied with SKU M323.J04 and GTIN 4061905072185 for straightforward inventory and traceability. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
19.05mm Gauge Pin 50mm Length Workshop Finish - Metav IndustryLine
Take advantage of the combination of workshop-grade robustness, ±0.002 mm accuracy and a compact Ø 19.05 mm / 50 mm form factor for reliable end‑measurement in inspection and fixture work; order the gauge pin directly via Metav Werkzeuge or ask the consultants for application advice. Gauge pin M323.J05 — Gauge pin, Ø 19.05 mm, 50 mm length (Metav IndustryLine) The Gauge pin M323.J05 is a workshop-grade precision gauge pin designed for end‑measurements, bore verification and fixture alignment in metalworking and toolmaking environments. Ø 19.05 mm, 50 mm length Accuracy ±0.002 mm Workshop version for frequent use Supplied in transport case Reliable precision for inspection and tooling Engineered for repeatable results, this gauge pin delivers ±0.002 mm tolerance, making it suitable where tight dimensional control is required. The component’s special steel construction provides a stable contact surface that resists wear during repeated insertion and withdrawal cycles, which helps to maintain measurement certainty over many inspection runs. As a single, purpose‑made measuring element, it performs plug and end‑measurements with minimal setup, reducing measurement time and the risk of operator error. Robust handling and compact geometry With a 50 mm length and Ø 19.05 mm diameter, the pin combines easy handling with sufficient engagement depth for most bore checks and locating tasks. The workshop version indicates a focus on durability under frequent use: hardened surfaces and a precision ground finish help to reduce scoring and maintain roundness. Supplied in a transport case, the component stays protected during storage and transit, preserving its calibration state and reducing unplanned downtime for replacements. Micro‑range suitability and application areas Falling into the micro range for measuring tools, the pin is optimised for fine mechanical assemblies, small bore inspection and tooling set‑ups where compact gauges are required. Typical applications include end‑measure verification of shafts, plug checks in fixture manufacture and quick go/no‑go checks during assembly. The compact design offers a straightforward integration into quality control routines and jigs, supporting faster throughput while keeping tolerances tight. For workshop-ready precision from Metav IndustryLine, contact Metav Werkzeuge in Emmerich for tailored advice and secure procurement that keeps production moving. Technical data Article number: M323.J05 GTIN: 4061905072192 Material: Special steel Design: Workshop version Packaging: Transport case included Facts Diameter: 19.05 mm Length: 50 mm Weight: 0.2 kg Tolerance: ±0.002 mm Special features Single piece gauge pin Compact, precision ground geometry Intended for end‑measurement and bore checks Suited to frequent use in workshop environments FAQ What level of accuracy can be expected from this gauge pin? The gauge pin M323.J05 is specified with an accuracy of ±0.002 mm, making it suitable for precision inspection and tooling tasks where tight tolerances are required. Which materials is the pin suitable for contacting? Constructed from special steel, the pin is intended for contact with typical engineering materials during inspection; its hardened surface is designed to resist wear in regular workshop use. Is the pin supplied ready for use and protected for transport? The gauge pin is supplied as a single unit and delivered in a transport case to protect the ground surface and ensure readiness for inspection tasks. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
19.06mm Gauge Pin, Single, 50mm Length Workshop Version - Metav IndustryLine
Taking advantage of ±0.002 mm accuracy, a Ø19.06 mm nominal diameter and a 50 mm length, this gauge pin delivers repeatable end‑dimension checks in workshop environments; order the part directly via Metav Werkzeuge or consult their specialists for set options. Gauge Pin M323.J06 — 19.06 mm diameter, 50 mm length (Metav IndustryLine) A Gauge Pin M323.J06 designed for precise end‑dimension checks and reference measurements in workshop use. Factory tolerance ±0.002 mm Diameter Ø19.06 mm, length 50 mm Manufactured from special steel Supplied in transport case Reliable accuracy for end‑dimension control The M323.J06 is built to provide repeatable measurements where end masses and mating fits determine assembly quality. With a stated tolerance of ±0.002 mm, the pin serves as a reliable reference for gauging and inspection tasks that demand tight limits. The narrow tolerance reduces measurement scatter and supports statistical process control; technicians benefit from consistent pass/fail decisions and fewer reworks when the reference standard is stable. Built as a gauge pin, it is intended for direct comparison, plug checks and go/no‑go functions in production and assembly. Durable workshop design that keeps measurement stable Manufactured from special steel and offered in a workshop version, this reference pin prioritises wear resistance and dimensional stability under repeated handling. The 50 mm shank provides a balanced length that avoids unnecessary flex while the Ø19.06 mm nominal diameter matches commonly required end‑dimension gauges. Supplied in a transport case, the component is protected against transit damage and contamination, helping to preserve surface finish and accuracy between uses. The rugged design supports daily use in maintenance, jigs and tool rooms where downtime must be minimised. Integrates easily into inspection routines and systems Designed for straightforward integration into measurement procedures, the pin suits comparative checks, end‑dimension verification and assembly trials. Labelling and identification via SKU and GTIN allow traceability through inventory and quality records, while the compact form factor simplifies storage and handling. The pin’s nominal dimensions and ±0.002 mm specification make it a practical addition to inspection benches and gauge sets, enhancing process capability metrics with minimal setup. For tailored configurations or set combinations, Metav IndustryLine offers accessory and set options to match line inspection requirements. Contact Metav Werkzeuge for specification advice on the M323.J06 gauge pin and to arrange supply or set configuration from Emmerich: info@metav-werkzeuge.com / +49 2822 7131930 Technical data Article number: M323.J06 GTIN: 4061905072208 Manufacturer: Metav IndustryLine Facts Diameter: 19.06 mm Length: 50 mm Tolerance: ±0.002 mm Weight: 0.2 kg Special features Material: special steel Workshop version Supplied in transport case Category: Gauge pin (Messstifte) FAQ What applications is this gauge pin intended for? The Gauge Pin M323.J06 is intended for end‑dimension checks, plug inspections and reference measurements in workshop and production environments where precise mating dimensions are required. Is a calibration certificate supplied with the pin? The product data for the M323.J06 does not specify a calibration certificate; the listing describes the gauge pin and its specifications only. What material and durability can be expected from this pin? Made from special steel and offered in a workshop version, the M323.J06 emphasises resistance to wear and dimensional stability for frequent handling. Can this pin be used for both hole and shaft checks? The gauge pin functions as a reference for end‑dimension and plug checks; it is suitable for verifying hole fits and mating shaft dimensions when used with appropriate fixtures. How is the item supplied and how can it be identified in stock? The M323.J06 is supplied in a transport case and can be identified by Article number M323.J06 and GTIN 4061905072208. Metav IndustryLine: Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
19.07mm Gauge Pin Single 50mm Length Workshop Version - Metav IndustryLine
Take advantage of the combination of precise sizing, robust workshop construction and fine tolerance control for reliable end‑of‑line checks; the Ø 19.07 mm diameter together with a ±0.002 mm tolerance ensures consistent fit verification. Order the gauge pin directly via Metav Werkzeuge or consult the specialists for application advice. Gauge pin M323.J07 — single test pin, Ø 19.07 mm, 50 mm length (Metav IndustryLine) Gauge pin M323.J07 is a purpose‑built test pin for precise end‑measure checks and fit verification in workshop inspection and assembly tasks Workshop version for robust use Precision diameter Ø 19.07 mm Tight tolerance ±0.002 mm Compact 50 mm length for bench work Precision in compact dimensions for repeatable checks The Ø 19.07 mm diameter combined with a ±0.002 mm tolerance places this test pin in a precision class suitable for fine fit testing and acceptance checks. Classified within the Micro category (measurement range 10–100 mm), the component offers the accuracy expected where small clearances matter. The narrow tolerance reduces measurement scatter during repeated insertions, which supports faster decision making on the production line and fewer reworks. Robust workshop design and material for everyday use Constructed in special steel, the pin is engineered as a workshop version to withstand routine handling and frequent use at the inspection bench. The 50 mm length and modest mass make the object easy to position and manipulate without sacrificing rigidity, so operators obtain stable contact conditions. The material choice balances surface hardness and corrosion resistance consistent with a tool intended for regular dimensional verification rather than long‑term abrasive duty. Clear function: end‑measure verification and fit testing Designed primarily for end measurements and fit testing, the pin provides a reliable datum for gauging bores, guides and mating components where exact bores or plug fits must be checked quickly. The narrow tolerance helps detect deviations that would otherwise affect assembly quality. In practical terms, the pin is a simple, effective instrument for go/no‑go style checks and for confirming final dimensions before downstream processes. Traceability and compact handling for workshop logistics The small footprint facilitates tidy storage and straightforward inventory management while maintaining traceability through the product identifiers. The compact design supports rapid throughput in inspection routines and simplifies handling during sample checks on the shopfloor. For businesses seeking a repeatable, low‑complexity gauging tool, this pin complements both manual inspection setups and semi‑automated test stations. For precise end‑of‑line and fit verification choose the Metav IndustryLine gauge pin and contact Metav Werkzeuge in Emmerich for availability and specification guidance — eMail: info@metav-werkzeuge.com | Tel: +49 2822 7131930 Technical data Article number: M323.J07 GTIN: 4061905072215 Label: Gauge pin, single, 19.07 mm, length 50 mm Manufacturer: Metav IndustryLine Measured values Diameter: 19.07 mm Length: 50 mm Tolerance: ±0.002 mm Weight: 0.2 kg Materials & features Material: Special steel Version: Workshop execution Application: End‑measure verification and fit testing Category: Micro (measurement range 10–100 mm) FAQ What is the intended use of this gauge pin? The gauge pin M323.J07 from Metav IndustryLine is intended for end‑measure verification and fit testing of bores and mating features in workshop inspection tasks. How precise is the test pin for repeated checks? The pin carries a tolerance of ±0.002 mm, which supports consistent detection of small deviations during repeated insertions and routine go/no‑go checks. Is the pin supplied with any calibration documentation? The product data does not indicate that a calibration certificate is supplied with the gauge pin. What is the pin made from and how durable is it? Manufactured from special steel, the pin is configured as a workshop execution to withstand regular handling and provide a balance of hardness and everyday durability. Which measurement category does this pin belong to? With a diameter of 19.07 mm it falls into the Micro range (10–100 mm), making it suitable for fine mechanical and small‑component measurement tasks. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
19.08mm Test Pin 50mm Length Workshop Version - Metav IndustryLine
Combining workshop-grade construction, a precise 19.08 mm diameter and a compact 50 mm length, this gauge pin ensures consistent reference measurements and reliable fixture checks. Order the part directly via Metav Werkzeuge or ask our consultants for application advice. Gauge pin M323.J08 — 19.08 mm diameter, 50 mm length (Metav IndustryLine) The gauge pin M323.J08 is a workshop‑grade reference pin with a precise 19.08 mm diameter and 50 mm length for inspection, fixture set-up and dimension verification in routine production environments. Workshop-grade construction for daily use Diameter 19.08 mm, tolerance ±0.002 mm Length 50 mm for fixture and reference checks Special steel for wear resistance Consistent reference for routine inspection A compact, workshop-grade gauge pin provides a stable reference point for repetitive checks and quick go/no‑go tests. The controlled 19.08 mm diameter combined with a verified ±0.002 mm tolerance reduces uncertainty in pass/fail decisions, supporting faster throughput on the shop floor. The short 50 mm shank keeps the pin stiff under manual handling, which is particularly beneficial when rapid, repeatable checks are required in production or maintenance workflows. Material choice and longevity Built from special steel, the pin resists wear and preserves its measuring edge over extended use, so calibration intervals are extended and downtime is reduced. The special steel construction also ensures dimensional stability under typical workshop conditions; this results in a dependable reference that maintains its function across many cycles, lowering the total cost of ownership for routine measurement tasks. Easy integration with fixtures and gauges The design suits common fixture arrangements and manual checking tools, allowing straightforward incorporation into existing inspection rigs. Its compact geometry and 50 mm length make the pin suitable for confined spaces and modular jigs. As a result, setup time is minimised and measurement routines are streamlined, supporting consistent quality control without complex retooling. For dependable workshop reference measurements, choose the Metav IndustryLine M323.J08 and contact Metav Werkzeuge for tailored advice or to arrange supply — eMail: info@metav-werkzeuge.com or call +49 2822 7131930 Technical Data Article number: M323.J08 SKU: M323.J08 GTIN: 4061905072222 Category: Messstifte Data Diameter: 19.08 mm Length: 50 mm Tolerance/accuracy: ±0.002 mm Weight: 0.2 kg Special features Material: Special steel Version: Workshop execution Application: Reference and fixture checks FAQ What is the intended use of this gauge pin? The gauge pin M323.J08 is designed for workshop reference measurements, fixture alignment and routine inspection tasks where a precise 19.08 mm reference is required. How precise is the diameter of the pin? The diameter is specified as 19.08 mm with an accuracy of ±0.002 mm, providing a stable reference for go/no‑go and comparative checks. Is the material suitable for heavy use? Yes. The pin is made of special steel and its workshop execution is intended for regular use, offering wear resistance and dimensional stability. Can this pin be used in assembly fixtures? The 50 mm length and compact form factor make the pin suitable for many fixture layouts and confined assembly spaces. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
19.09mm Gauge Pin 50mm Length Workshop Version - Metav IndustryLine
Take advantage of precise end‑dimension checks with a robust workshop design and tight tolerance control: the combination of ±0.002 mm repeatability, 19.09 mm nominal diameter and a 50 mm overall length supports reliable fit verification and reduces rework in production. Order the gauge pin directly via Metav Werkzeuge or ask our consultants if needed. Gauge pin M323.J09 — 19.09 mm diameter, 50 mm length (Metav IndustryLine) The gauge pin M323.J09 is a single precision pin for end‑dimension and fit checks in workshop and inspection routines, offering a compact, wear‑resistant solution for routine gauging. Workshop version for robust use Diameter 19.09 mm, length 50 mm Special steel, tolerance ±0.002 mm Repeatable end‑dimension checks that reduce scrap A compact precision pin engineered for consistent dimensional control, the gauge pin provides a direct, verifiable measure of bore and pin fits. With a nominal 19.09 mm diameter and a specified ±0.002 mm tolerance, it enables close pass/fail decisions during assembly and inspection. The fine tolerance reduces uncertainty in go/no‑go checks and supports tighter production tolerances without requiring complex fixtures. This reliability shortens inspection loops and contributes to a smoother production flow. Robust workshop design for continuous use Built as a workshop execution, the pin is made from special steel to withstand repeated handling and routine contact with mating surfaces. The compact 50 mm overall length offers easy manoeuvrability while maintaining stiffness for stable measurements. Delivered in a transport case, the item is protected during storage and transit, reducing the risk of damage that would otherwise impair the gauge’s accuracy. The solid construction eases daily use in busy maintenance or machine‑shop environments. Simple integration into inspection processes Designed for pragmatic use in metrology benches and assembly stations, the pin is marked and identified for straightforward inventory and traceability. The clear dimensional specification aids process planning: use it for final dimension checks, go/no‑go verification and assembly validation where a precise reference pin is required. The compact format allows immediate hand inspection or placement in simple gauging jigs, helping to speed up routine checks while retaining measurement integrity. Contact Metav Werkzeuge for a technical quote, availability and delivery details for the Metav IndustryLine gauge pin M323.J09. Technical Data Article number: M323.J09 GTIN: 4061905072239 Manufacturer: Metav IndustryLine Dimensions & tolerances Diameter: 19.09 mm Length: 50 mm Tolerance: ±0.002 mm Weight: 0.2 kg Special features Material: Special steel Workshop version Delivered in transport case ECLASS: 21170231 FAQ What tolerance can be expected from this gauge pin? The gauge pin delivers a tolerance of ±0.002 mm, which supports precise end‑dimension verification for accurate fit and go/no‑go assessments. Is the gauge pin suitable for routine workshop use? Yes, the workshop execution and special steel construction make the pin suitable for regular handling and service environments typical of machine shops. Which identification should be used when ordering replacement pins? Order using the article number M323.J09 or the GTIN 4061905072239 to ensure the correct Metav IndustryLine gauge pin is supplied. Can the pin be used for both bore checking and assembly verification? The design of the pin allows straightforward use for bore and fit checks as well as assembly verification where a precise reference diameter is required. Metav IndustryLine: Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
19.11mm Gauge Pin 50mm Length Workshop Version - Metav IndustryLine
Take advantage of high repeatability and fine tolerance to secure consistent end‑measurements in inspection routines; the combination of ±0.002 mm accuracy and a robust special steel construction ensures dependable results and long service life. Order directly via Metav Werkzeuge or consult our specialists for application advice. Gauge pin M323.J11 – 19.11 mm diameter, 50 mm length (Metav IndustryLine) A gauge pin M323.J11 engineered for precise end‑measurements and fixture checking in workshop and inspection environments. Workshop version for robust daily use Precision tolerance ±0.002 mm 19.11 mm diameter, 50 mm length Delivered in protective transport case Accurate end‑measurement for repeatable inspection results The M323.J11 gauge pin combines a 19.11 mm diameter with an exact 50 mm length, delivering a ±0.002 mm tolerance that supports strict quality control workflows. Machined from special steel, the pin retains its dimensional integrity under frequent handling and provides stable reference points for bore gauges, plug checks and assembly verification. This level of precision reduces unclear measurements and helps to lower scrap rates by ensuring that pass/fail decisions are based on reliable, repeatable data. Workshop‑ready handling that speeds up everyday checks Designed as a workshop version, this single gauge pin is optimised for routine use: its compact form and balanced mass assist secure seating in fixtures and minimise wobble during measurement. Supplied in a protective transport case, the pin is ready for storage and safe transfer between inspection stations. The combination of a sturdy material and finish means less maintenance and predictable behaviour across repeated cycles, supporting faster inspection throughput without sacrificing measurement quality. Simple integration into quality procedures and inventory The gauge pin is supplied with clear identification (SKU M323.J11, GTIN 4061905072253), which streamlines tracking within existing inspection inventories and work instructions. As a workshop inspection tool, it is suitable for end‑measurements and spot checks in production and maintenance workflows. The robust specification makes it a reliable choice for both standalone checks and as part of jigs or go/no‑go assemblies, enabling consistent measurement standards across shifts and locations. Contact Metav Werkzeuge for a tailored application review and reliable supply direct from Emmerich – technical advice and rapid dispatch are available Technical data Article number: M323.J11 GTIN: 4061905072253 Manufacturer: Metav IndustryLine Facts Diameter: 19.11 mm Length: 50 mm Tolerance: ±0.002 mm Weight: 0.2 kg Special features Material: special steel Workshop version Delivered in protective transport case Category: gauge pins (Messstifte) FAQ What measurement accuracy can be expected from this gauge pin? The gauge pin provides an accuracy of ±0.002 mm, making it suitable for tight inspection tolerances in workshop and production environments using the M323.J11. Is the gauge pin suitable for use in fixtures and jigs? Yes. The M323.J11 is designed as a workshop version and is well suited for use in fixtures, jigs and as a reference for plug and bore checks. What material is the pin made from and how does that affect durability? The pin is machined from special steel, which offers durable dimensional stability under frequent handling and supports long service life in inspection routines. How is the product identified for inventory and ordering? This gauge pin is supplied as SKU M323.J11 with GTIN 4061905072253 for easy tracking in procurement and inventory systems. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
19.12mm Test Pin, Single, 50mm Length, Workshop Version - Metav IndustryLine
Take advantage of a compact inspection tool that pairs robust workshop construction with ±0.002 mm tolerance for dependable end‑of‑line checks; the combination of special steel and a 50 mm working length supports repeatable fit verification on medium-sized components. Order the gauge pin directly via Metav Werkzeuge or consult our specialists if clarification is needed. Gauge pin M323.J12 — Ø 19.12 mm, 50 mm length (Metav IndustryLine) The Gauge pin M323.J12 is a single precision test pin designed for fast end‑measurement and fit checks in workshop and production environments. Workshop version, robust design Diameter Ø 19.12 mm for precise fits Length 50 mm suitable for insertion checks Tolerance ±0.002 mm for consistent results Assured dimensional control for assembly and inspection A compact, single gauge pin delivers a straightforward way to verify bore sizes, clearances and end measurements without complex set‑ups. The Ø 19.12 mm diameter, manufactured from special steel, ensures dimensional stability during repeated use; the fine tolerance of ±0.002 mm limits uncertainty and supports quick go/no‑go decisions on the shop floor. This reduces rework and keeps throughput steady, making the pin an efficient tool for routine quality control. Designed for frequent workshop handling The workshop specification focuses on durability and ease of handling: a 50 mm working length gives enough engagement depth for reliable seating while keeping the pin short enough for rapid insertion and removal. The special steel composition provides wear resistance under everyday use, preserving the calibrated diameter across many cycles. The solid construction and compact geometry make the pin practical for operators who need a simple, repeatable measure rather than an elaborate gauging fixture. Practical application and benefit for production teams In practice, a single precision pin is used to check component bores, mating features and alignment during assembly operations. The form factor supports quick manual checks and can be integrated into small fixtures as a reference probe. Because the pin is produced to a close tolerance, it helps to detect deviations early, avoiding assembly errors and downtime. The clear, decisive results from such a pin simplify inspection routines and support traceable quality processes. For reliable workshop inspection choose the Metav IndustryLine gauge pin M323.J12 and contact Metav Werkzeuge in Emmerich at +49 2822 7131930 or info@metav-werkzeuge.com for specification advice or order information Technical data Article number: M323.J12 GTIN: 4061905449536 Description: Single gauge pin, end measurement tool Material: Spezial‑Stahl Weight: 0.2 kg Facts Diameter: 19.12 mm Length: 50 mm Tolerance: ±0.002 mm Label: Prüfstift, einzeln, 19,12 mm Länge 50 mm Special features Workshop execution (robust design) Single precision test pin Intended for end measurements (endmasse) Compact format for frequent handling FAQ What tolerance does the gauge pin offer? The Metav IndustryLine gauge pin M323.J12 is manufactured to a tolerance of ±0.002 mm, providing tight dimensional control for inspection tasks. What is the material of the pin and how does it affect use? The pin is made from special steel; this material choice improves wear resistance and dimensional stability during repeated insertion checks. Is this a single or set item, and how is it used in inspection? This is a single precision test pin (gauge pin) intended for quick bore and fit verification; the 50 mm length gives reliable engagement for end‑of‑line checks. Can the pin be integrated into fixtures or jigs? Yes, the compact geometry and accurate diameter make the pin suitable for use as a reference element in small fixtures and gauging arrangements. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
19.13mm Gauge Pin Workshop Version 50mm Length - Metav IndustryLine
Take advantage of a precisely matched diameter of 19.13 mm, a tight tolerance of ±0.002 mm and a compact 50 mm length for reliable end‑measurements; order the gauge pin directly via Metav Werkzeuge or contact our consultants for application advice. Single gauge pin 19.13 mm — plug gauge, 50 mm length (Metav IndustryLine) Single gauge pin 19.13 mm is a workshop-grade plug gauge designed for end‑measurements and fit checks in machining and inspection tasks. Workshop version for robust use Diameter tolerance ±0.002 mm Special steel construction Delivered in protective transport case Precision where fit and repeatability matter The plug gauge is manufactured to a diameter of 19.13 mm with an accuracy of ±0.002 mm, providing consistent go/no‑go checking and reference measures for assembly and quality control. The tight tolerance reduces rework by detecting marginal fits early in the process, while the compact 50 mm length keeps handling straightforward in confined fixturing. This tool functions as a quick, repeatable reference in production routines and inspection benches. Durable design for workshop environments Built in a workshop version and made from special steel, the pin resists wear under frequent use and maintains dimensional stability during standard handling. The single‑piece design minimises joint errors and is suited to repetitive insertion checks. Supplied in a protective case for transport, the gauge arrives ready for use at the bench or in the tool cabinet, reducing the risk of damage during storage and transit. Integration into quality workflows As a simple, calibrated reference for end‑measurements, this plug gauge supports streamlined inspection procedures and traceable checks during assembly. The clear numeric specification and robust material choice enable easy incorporation into control sheets and inspection plans. The compact format suits shopfloor use where quick verification is required without the overhead of complex measuring systems. Contact Metav Werkzeuge for precise application guidance or to request batch availability of Metav IndustryLine gauge pins and accessories Technical Data Article number: M323.J13 GTIN: 4061905449543 Category: Messstifte Facts Diameter: 19.13 mm Length: 50 mm Tolerance: ±0.002 mm Weight: 0.2 kg Special features Material: Special steel Workshop execution Single gauge pin, individual delivery Supplied in protective transport case FAQ What is the purpose of this gauge pin? The gauge pin is used for quick end‑measurements and fit checks; the single gauge pin 19.13 mm from Metav IndustryLine provides a defined reference diameter for go/no‑go assessments. Is the tolerance suitable for industrial fit checks? Yes, the ±0.002 mm tolerance makes the pin appropriate for precise fit and assembly checks in standard machining and inspection tasks. What material is the pin made from and why does it matter? The pin is manufactured from special steel, chosen for wear resistance and dimensional stability under regular workshop use. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
19.14mm Gauge Pin 50mm Length Workshop Version - Metav IndustryLine
Take advantage of the combination of ±0.002 mm tolerance, a precise 19.14 mm diameter and a 50 mm gauge length for reliable end‑size verification across workshop routines; order the part directly via Metav Werkzeuge or consult our specialists for application advice. Gauge pin M323.J14 — 19.14 mm diameter, 50 mm length (Metav IndustryLine) The gauge pin M323.J14 is a single inspection pin designed for precision end‑size checks and fixture setting in industrial metrology and workshop environments. High-precision ±0.002 mm tolerance 19.14 mm diameter for end-size control 50 mm length for versatile fixture use Workshop version for everyday handling Precision for repeatable end-size verification A compact precision pin delivers reproducible measurements where tolerance banding is tight. The inspection pin is manufactured from special steel and produced to a verified run that achieves a ±0.002 mm deviation, which makes it suitable for fine checks during assembly, quality control and tool setting. Because the diameter is specified as 19.14 mm, the component fits gauges and bores designed around that nominal size, reducing interpretation effort in test plans. The result is a measurable reduction in rework and quicker go/no‑go decisions on the production line. Robust workshop design for daily use The component’s 50 mm shank length provides a good balance between reach and rigidity for routine applications; paired with a mass of 0.2 kg, the item remains easy to handle while feeling substantial in the hand. The workshop version construction emphasises durable finishing and dimensional stability under typical shop conditions, so the pin stands up to repeated seating in jigs and go/no‑go fixtures. This combination supports steady throughput and lowers the risk of introducing handling errors during frequent checks. Simple integration into inspection and tooling processes Inspection pins such as this are straightforward to incorporate into existing gauge sets, mandrels and fixture assemblies. The single‑piece design avoids alignment ambiguity and is ideal for end‑size confirmation, setting centre distances and checking bore runs. Traceable identification and a clear SKU (M323.J14) allow fast procurement and inventory control, while the Metav IndustryLine positioning ensures compatibility with a broad range of workshop metrology supplies. For workshops seeking dependable precision without overcomplex instrumentation, this inspection pin is a pragmatic choice. Contact Metav Werkzeuge for tailored advice and quick supply from Emmerich — ask for M323.J14 to confirm suitability for the intended application Technical data Article number: M323.J14 GTIN: 4061905449994 Brand: Metav IndustryLine Dimensions & tolerances Diameter: 19.14 mm Length: 50 mm Tolerance: ±0.002 mm Weight: 0.2 kg Materials & special features Material: special steel Version: workshop execution Single gauge pin for end-size and fixture checks FAQ What is the stated diameter accuracy of this gauge pin? The gauge pin is manufactured to a tolerance of ±0.002 mm, ensuring high repeatability for end‑size checks. Can this pin be used in fixture setting and gauge blocks? Yes, the 50 mm length and single‑piece design make the pin suitable for fixture setting, mandrel use and integration with gauge stacks. Is the material suitable for regular workshop use? The pin is made from special steel and is supplied in a workshop execution that emphasises robustness for frequent handling. How is the product identified for ordering and inventory? Refer to SKU M323.J14 and GTIN 4061905449994 when ordering to ensure quick identification and replenishment. Which brand supplies this gauge pin and what does that imply? This item is part of the Metav IndustryLine, indicating access to a wide range of complementary metrology products and consistent quality control. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
19.15mm Gauge Pin Length 50mm Workshop Version, Special Steel - Metav IndustryLine
Take advantage of the combination of high dimensional accuracy, robust special‑steel construction and protected transport packaging to ensure reliable end‑measure checks in daily workshop use. Order the gauge pin directly via Metav Werkzeuge or consult our specialists for matching reference gauges and delivery options. Gauge pin M323.J15 — single precision plug, Ø 19.15 mm, 50 mm length (Metav IndustryLine) The gauge pin M323.J15 is a single, workshop‑grade plug designed for precise end‑dimension verification and reference‑pin duties in mechanical inspection and assembly tasks. Workshop version, hardened for daily use Dimensional accuracy ±0.002 mm Diameter 19.15 mm, length 50 mm Supplied in protective transport case Repeatable precision for end‑dimension checks The core advantage lies in the dimensional accuracy ±0.002 mm, which supports repeatable measurements and tight tolerance verification on production lines. The pin’s nominal diameter 19.15 mm and 50 mm length provide a stable reference for end‑measurements and fit checks; this reduces rework and accelerates quality decisions during inspection. The stated tolerance corresponds to industrial metrology demands where consistent, verifiable reference standards improve throughput and reduce measurement uncertainty. Robust workshop design that withstands daily handling Manufactured from special steel, the pin is engineered for durability in workshop environments. The workshop version construction balances surface hardness with corrosion resistance for long service life under cyclical use. Supplied in a protective transport case for safe handling and reduced contamination, the pin remains ready for immediate use at the gauge block, fixture or assembly station. This construction minimises downtime for replacements and conserves calibration intervals. Practical integration into inspection routines As a single gauge pin, the item is suitable for insert checks, bore gauging and end‑measure validation where a defined reference diameter is required. The compact form factor simplifies storage and handling on inspection benches and in tool kits. Use as a reference for setting go/no‑go fixtures or as a master plug when establishing mating fits; the simple geometry eases interpretation of results and keeps inspection workflows efficient and transparent. Clear identification and safe storage for traceability The component is identified by SKU M323.J15 and GTIN for inventory control and traceability within the quality system. Lightweight yet stable at 0.2 kg, the pin can be logged into tool management software or stored with protective accessories to preserve metrological integrity. Packaging in a dedicated transport case reduces the risk of nicks or contamination that could affect diameter and performance, supporting reproducible measurements over extended service periods. Contact Metav Werkzeuge today to discuss application matching, delivery options and complementary reference gauges for workshop inspection tasks Technical Data Article number: M323.J15 GTIN: 4061905071232 Label: Gauge pin, single, 19.15 mm, length 50 mm Facts Diameter: 19.15 mm Length: 50 mm Weight: 0.2 kg Accuracy: ±0.002 mm Special features Material: special steel Workshop version Supplied in protective transport case Category: Gauge pins FAQ What applications suit this gauge pin? The gauge pin M323.J15 is intended for end‑dimension checks, bore gauging and use as a reference plug in inspection and assembly routines. Is the dimensional tolerance sufficient for industrial inspection? Yes, the ±0.002 mm accuracy of the M323.J15 meets common industrial requirements for repeatable reference measurements in workshop and production environments. How is the pin supplied and protected in transit? The gauge pin M323.J15 is supplied in a protective transport case to prevent damage and preserve the reference surface during storage and transport. Can the M323.J15 be used as a master for fixture set‑up? The single gauge pin M323.J15 is suitable for setting fixtures and go/no‑go checks where a defined reference diameter and stable seating are required. How should the pin be stored to maintain accuracy? Store the M323.J15 in its protective case and avoid contact with abrasive surfaces; log the item under inventory control to support traceability and regular inspection. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
19.16mm Gauge Pin Single 50mm Length Workshop Finish - Metav IndustryLine
Benefit from consistently repeatable measurements thanks to a tight tolerance of ±0.002 mm, a compact 19.16 mm diameter and a 50 mm length in a workshop-ready design; order the gauge pin directly via Metav Werkzeuge or ask our consultants if needed. Gauge pin, single — 19.16 mm diameter, 50 mm length (Metav IndustryLine) A gauge pin, single, 19.16 mm, 50 mm long designed for precise end‑measurements and fixture verification in workshop and inspection environments Precision tolerance ±0.002 mm Diameter 19.16 mm, length 50 mm Made from special steel for durability Workshop version with transport case Repeatable accuracy for inspection and tooling The gauge pin is engineered to deliver repeatable measurement accuracy, with a specified deviation of ±0.002 mm. Such a tight tolerance places the component among high‑precision workshop gauges, making it suitable as a reference for go/no‑go checks, end‑measurements and for verifying jig and fixture seating. The compact geometry keeps thermal mass low, which reduces dimensional drift during short inspection cycles and contributes to consistent results across batches. Compact format that supports versatile workshop use Classified in the micro measurement range (10–100 mm), this compact gauge pin combines reach and rigidity in a small footprint. The 19.16 mm diameter and 50 mm length are balanced to resist bending while remaining easy to handle on the production bench. The configuration suits gauging of bores, dowel seats and end faces where a precise hard reference is required, and its form factor integrates cleanly with existing inspection fixtures and test stands without obstructing access. Durable material and practical delivery for daily operation Manufactured from special steel, the pin is finished to withstand repeated seating and handling in a workshop environment, while preserving the original diameter over prolonged use. The workshop specification includes delivery in a dedicated transport case, ensuring safe storage and protection against knocks during logistics. Where traceability of the component is needed, the clear product identification simplifies inventory control and replacement planning. Contact Metav Werkzeuge to discuss application details and secure this Metav IndustryLine gauge pin with workshop transport case Technical Data Article number: M323.J16 GTIN: 4061905071249 Manufacturer: Metav IndustryLine Facts Diameter: 19.16 mm Length: 50 mm Tolerance: ±0.002 mm Weight: 0.2 kg Special features Material: special steel Workshop execution Delivered in transport case FAQ What level of accuracy can be expected from this gauge pin? The gauge pin delivers a specified accuracy of ±0.002 mm, which makes the Metav IndustryLine gauge pin M323.J16 suitable for fine workshop verification and reference checks. Is the pin suitable for repeated use in fixture locating applications? Yes, the special steel construction of the Metav IndustryLine gauge pin withstands repeated seating and provides long‑term dimensional stability for fixture locating and dowel checks. Does the delivery include protective packaging? Delivery of the gauge pin includes a transport case, providing protection during storage and transport and helping to maintain the pin’s calibrated condition. Can this pin be used for bore verification and end‑face checks? The 19.16 mm diameter and 50 mm length are well suited to bore verification and end‑face measurements where a compact, rigid reference is required. How is the product identified for inventory and reordering? The part is listed as M323.J16 (Metav IndustryLine) with GTIN 4061905071249 for straightforward inventory control and reordering. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
19.17mm Gauge Pin 50mm Length Workshop Version - Metav IndustryLine
Take advantage of workshop-grade durability, a compact 19.17 mm gauge diameter and ±0.002 mm repeatability for reliable end-measure checks in production. Order this precision gauge pin directly via Metav Werkzeuge or contact our consultants for specification advice. Measuring pin M323.J17 — Single precision gauge pin, 19.17 mm diameter, 50 mm length (Metav IndustryLine) The Measuring pin M323.J17 serves as a compact, single reference for end-measure checks and go/no-go gauging in workshop and production settings, designed for repeated use where dimensional certainty is required Workshop-grade construction for daily use Diameter 19.17 mm for end-measure checks Tolerance ±0.002 mm for high repeatability Delivered in transport case for safe handling Precision that keeps inspection consistent Engineered for high-repeatability reference checks, this gauge pin delivers a measurement tolerance of ±0.002 mm, which positions it as a precision tool for tight inspection tolerances. The narrow 19.17 mm diameter is specified for end-measure comparisons and dimensional verification; its performance reduces uncertainty during quick go/no‑go checks and helps maintain process control. Traceable identifiers support documentation and batch control, aiding quality assurance workflows. Built for the workshop: compact, robust and protected The pin is produced in special steel and finished for routine industrial handling, reflecting the stated workshop execution. A 50 mm shaft length provides adequate engagement without excess overhang, while the compact form factor keeps handling straightforward and ergonomic. Delivery in a dedicated transport case preserves the reference surface during storage and transit, helping to maintain calibration and surface integrity between uses. Integrating a reliable gauge into inspection routines As a single precision gauge pin, M323.J17 is suitable for quick dimensional comparison and setting of fixtures where a stable reference diameter is required. The item is lightweight (0.2 kg) for easy handling and marked for traceability (GTIN: 4061905071256), simplifying inventory and inspection record-keeping. Incorporating this pin into periodic checks contributes to faster decision-making on the shop floor and supports consistent quality output across production batches. For workshop supply or a technical consultation about the M323.J17 precision gauge pin, contact Metav Werkzeuge directly at info@metav-werkzeuge.com or call +49 2822 7131930 — Metav’s specialists are available to advise on suitability and delivery. Technical data Article number: M323.J17 GTIN: 4061905071256 Label: Measuring pin, single, 19.17 mm, length 50 mm Facts Diameter / measurement range: 19.17 mm Length: 50 mm Weight: 0.2 kg Accuracy: ±0.002 mm Special features Material: Special steel Workshop version Delivered in transport case Single precision gauge pin for end-measure checks FAQ What is the intended use of this gauge pin? The M323.J17 measuring pin is intended for end-measure checks and reference gauging in production and workshop inspection routines. Is the material suitable for routine industrial use? Yes, the pin is made from special steel and supplied in a workshop execution designed for regular handling and wear resistance. How precise is the M323.J17 for dimensional checks? The pin provides a tolerance of ±0.002 mm, making it suitable for tight comparison checks and processes that demand high repeatability. How is the item identified for inventory and traceability? The M323.J17 is identifiable by its GTIN 4061905071256 and the article number M323.J17 for streamlined tracking. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
19.18mm Gauge Pin Length 50mm Workshop Finish - Metav IndustryLine
Precision end‑measurement with workshop robustness: the 19.18 mm gauge pin provides ±0.002 mm repeatability in a compact 50 mm length and is manufactured from special steel for dimensional stability—order directly via Metav Werkzeuge or consult our specialists for application guidance. Gauge pin M323.J18 – 19.18 mm Ø, 50 mm length (Metav IndustryLine) The Gauge pin M323.J18 is a workshop‑grade precision test pin intended for end‑measure verification, fixture alignment and repeatability checks in industrial metrology. Diameter 19.18 mm for tight tolerances Tolerance ±0.002 mm high precision Special steel for dimensional stability Workshop‑grade design for robust handling Consistent precision for production inspection The compact test pin delivers a reproducible datum for end‑measure checks, with a specified tolerance of ±0.002 mm that supports fine inspection tasks and high‑accuracy gauge set‑ups. This level of precision reduces measurement scatter at critical mating fits and minimises rework, which improves process yield. The nominal 19.18 mm diameter is suited to tight tolerance applications where a stable reference is required; by combining defined geometry with robust material selection, the pin performs reliably under repeated seating and release cycles. Built for everyday workshop use A 50 mm overall length and a workshop‑oriented construction ensure practical handling during fixture set‑up and inspection routines. The component’s 50 mm length provides sufficient engagement for end‑measure tasks while remaining short enough to avoid undue leverage or bending during manual handling. At approximately 0.2 kg, the pin balances feel and stability, making it straightforward to position in gauges, transfer fixtures or dedicated checking jigs. The workshop specification highlights durability and ease of use in routine quality control environments. Traceable supply and integration into inspection routines Supplied as a single gauge pin with a clear article identity, the component supports organised inventory and traceable deployment across workshops. The product is categorised for precision end‑measure tasks and is compatible with standard gauge systems and fixture bores used in machine‑shop inspection processes. Sourcing through Metav IndustryLine ensures access to a broad metrology portfolio and the logistical support of a specialist distributor that acts as a quality filter for the European market, helping to standardise tools across production sites. For precise end‑measurement requirements, choose the Metav IndustryLine gauge pin M323.J18 and contact Metav Werkzeuge for tailored advice and supply from Emmerich. Technical Data Article number: M323.J18 GTIN: 4061905071263 Manufacturer: Metav IndustryLine Facts Diameter: 19.18 mm Length: 50 mm Tolerance / Accuracy: ±0.002 mm Weight: 0.2 kg Special features Material: Special steel Category: Gauge pins / Messstifte Version: Workshop execution Intended use: End‑measure checks FAQ What is the stated accuracy of this gauge pin? The gauge pin is specified with an accuracy of ±0.002 mm, which makes the M323.J18 suitable for tight tolerance inspection tasks. Which material is the pin made from and why does it matter? The pin is made from special steel, chosen for its dimensional stability and resistance to wear in repeated seating operations. Can this pin be used in fixture alignment and transfer jigs? Yes, the 50 mm length and workshop design make the pin compatible with standard fixtures and transfer jigs for end‑measure verification. Is the M323.J18 supplied individually or in sets? This SKU is supplied as a single gauge pin (single piece) for targeted replacement or bespoke gauge build‑ups. How does this pin support repeatability in production checks? By providing a defined diameter and tight tolerance, the pin establishes a reliable datum that reduces variability between successive measurements. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
19.19mm Gauge Pin 50mm Length Workshop Version - Metav IndustryLine
Take advantage of the combination of workshop-grade robustness, ±0.002 mm precision and a compact 19.19 mm nominal diameter for reliable end‑measurement and go/no‑go checks. Order the gauge pin directly via Metav Werkzeuge or contact our consultants for application advice. Gauge pin, single, 19.19 mm, 50 mm (Metav IndustryLine) The Gauge pin, single, 19.19 mm, 50 mm is a workshop‑grade inspection pin designed for accurate plug checks, alignment and reference measurements in production and quality control environments. Workshop-grade construction Nominal diameter 19.19 mm High precision ±0.002 mm tolerance Compact 50 mm length Accurate repeatability for visual and tactile inspection A compact inspection pin with a nominal diameter of 19.19 mm and a short 50 mm length gives dependable stability during plug‑type measurements. The stated tolerance of ±0.002 mm supports tight acceptance criteria and reduces uncertainty in repetitive checks. By using a compact reference pin rather than adjustable gauges, measurement throughput is improved and non‑conforming parts are identified quickly, which contributes directly to shorter inspection cycles and fewer downstream rejects. Built for workshop use and long‑term reliability The pin is manufactured from special steel, processed to provide durable contact faces and consistent geometry over many cycles. The workshop‑grade execution emphasises robustness against everyday handling and integration into fixtures or end‑of‑line checks. The modest mass and compact form make the pin easy to seat in jigs and quick to exchange, while the solid construction retains roundness and surface integrity to maintain measurement confidence over time. Practical integration into inspection routines Marked with the product identifier and global article code, the inspection pin is straightforward to document within quality workflows. Its fixed diameter makes it ideal for setting references, verifying bore sizes or aligning components in assembly operations. The design supports fast go/no‑go decisions and can be combined with visual or tactile inspection procedures to enhance process control. For traceable inventory and procurement the product is supplied with a clear article code for simple record keeping in inspection plans. For workshop‑ready precision from Metav IndustryLine, contact Metav Werkzeuge in Emmerich for tailored advice and reliable supply. Technical data Article number: M323.J19 GTIN: 4061905071805 Category: Messstifte Dimensions & tolerances Diameter: 19.19 mm Length: 50 mm Tolerance: ±0.002 mm Weight: 0.2 kg Materials & features Material: Special steel Special feature: Workshop execution SKU: M323.J19 FAQ What is the primary application for this gauge pin? The gauge pin is intended for plug checks, alignment and reference measurements in production and quality control; the M323.J19 supports quick verification of bore diameters and fit conditions. Is the diameter stable enough for series inspection? Yes, the nominal 19.19 mm diameter with a ±0.002 mm tolerance is suitable for repeatable series checks and integration into inspection routines. Can this pin be used in fixtures and jigs? The compact 50 mm length and robust workshop construction make the inspection pin well suited for fixture mounting and frequent handling in assembly or test jigs. How is the product identified for procurement and traceability? The item is listed under SKU M323.J19 with GTIN 4061905071805 for straightforward tracking in purchasing and quality documentation. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
19.1mm Gauge Pin 50mm Length Workshop Version - Metav IndustryLine
Accurate, robust and workshop-ready: the gauge pin delivers a 19.10 mm nominal diameter with a tight ±0.002 mm deviation and a practical 50 mm length, ensuring repeatable fits for end and plug gauging. Order directly via Metav Werkzeuge or contact their technical advisors for procurement and compatibility advice. Gauge Pin M323.J10 — single 19.10 mm, 50 mm length (Metav IndustryLine) The gauge pin, single 19.1 mm, 50 mm length is a compact, workshop-grade measuring pin designed for precise end‑measurement and fit checking in general workshop and assembly environments. Precision ground 19.10 mm diameter Tight tolerance ±0.002 mm for repeatable fits 50 mm working length, workshop version Special steel for robust handling Consistent fits through controlled diameter and tolerance The measuring pin is precision-ground to a nominal 19.10 mm and specified to ±0.002 mm, which translates into highly consistent contact geometry for small‑format fit checks. Such a tight tolerance reduces stacking and assembly variance, making the pin suitable as a tactile reference when checking bores, plugs and mating parts. For operators unfamiliar with gauge nomenclature: the tolerance indicates the maximum permissible deviation from the nominal diameter, so a smaller value equals closer conformity and better interchangeability. Built for workshop use: robustness and handling benefits Manufactured in special steel and supplied in a workshop execution, the measuring pin balances surface hardness with practical durability. The 50 mm length provides adequate reach for many end‑measurement tasks while remaining easy to position by hand or in fixtures; an indicated weight of approximately 0.2 kg contributes to stable handling during manual checks. The robust construction means less frequent replacement and consistent tactile feedback during repetitive gauging operations, which improves throughput in busy production areas. Practical applications that improve inspection workflows As a single gauge pin, the component serves for end measurements, plug checks and pass/fail trials where a defined diameter is needed to verify mating clearances. Using a dedicated measuring pin for these tasks speeds up inspection routines and reduces reliance on improvised substitutes that can introduce measurement scatter. The pin’s precision and repeatability support quicker decisions at the bench, lowering rework and helping to maintain process stability across batches. Traceability, identification and integration into inventory The product is indexed for industrial procurement and traceability; the clear marking and catalog reference ease stockkeeping and integration into existing inspection sets. When used alongside calibrated inspection tools and documented procedures, the pin contributes to reproducible measurement chains. For purchasing or system integration, reference the catalogue identifier to ensure the correct diameter and length are supplied for the intended inspection tasks. For workshop-ready precision from the Metav IndustryLine gauge pin, contact Metav Werkzeuge in Emmerich for supply and technical guidance — phone +49 2822 7131930 or email info@metav-werkzeuge.com Technical data Article number: M323.J10 GTIN: 4061905072246 Brand: Metav IndustryLine Facts Diameter: 19.10 mm Length: 50 mm Tolerance: ±0.002 mm Weight: 0.2 kg eClass: 21170231 Special features Material: special steel Version: workshop execution Intended application: end measurements / fit checking Accuracy class: ±0.002 FAQ What accuracy can be expected from this gauge pin? The gauge pin M323.J10 from Metav IndustryLine is specified with a tolerance of ±0.002 mm, providing high repeatability for fit and end‑measurement checks. Which inspection tasks suit this pin best? This measuring pin is intended for end measurements, plug checks and basic pass/fail fit trials; the 19.10 mm diameter and 50 mm length make it suitable for many workshop and assembly applications. What material is the pin made of and how should it be cared for? The pin is made from special steel; for long service life, keep the surface clean and lightly oiled after use, and store in a dry, padded compartment to prevent nicks. Is this item traceable for catalogue and inventory purposes? Yes — the product is listed as M323.J10 (GTIN 4061905072246) to support stock management and procurement processes. Are other diameters and lengths available in the same series? Metav IndustryLine supplies a range of gauge pins across common diameters and lengths; reference M323.J10 when enquiring to ensure compatible replacements or complementary sizes. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
19.21mm Test Pin, Single, 50mm Length, Workshop Version - Metav IndustryLine
Take advantage of precise end‑measurement, robust workshop construction and consistent traceability to speed up inspection routines and reduce rework. Order the pin directly via Metav Werkzeuge or consult our technical advisors for application advice. Gauge pin M323.J21 — single pin, 19.21 mm diameter, 50 mm length by Metav IndustryLine The Gauge pin M323.J21 is designed for accurate end‑measure inspection and fits workshop environments where repeatable plug measurements are required. Workshop version for everyday use Diameter 19.21 mm with ±0.002 mm tolerance 50 mm length for recessed and through measurements Made from special steel for high wear resistance Repeatable end‑of‑line measurements with industrial accuracy The gauge pin offers a simple, reliable way to verify bore sizes and end‑masses. With a nominal diameter of 19.21 mm and a verified positional tolerance of ±0.002 mm, the pin provides a clear go/no‑go reference that reduces decision time during quality checks. The compact geometry and a 50 mm shank length make the pin suitable for both shallow and deeper bores, enabling fast in‑process inspections that cut down on measurement setup and throughput delays. Built for workshop resilience and easy handling Constructed in workshop version specification from special steel, the pin tolerates regular use in machine shops and inspection benches. The material choice gives wear resistance and good surface stability, which keeps the reference diameter stable over repeated cycles and minimises the need for frequent replacement. Its single‑piece design simplifies handling and storage; when used with standard inspection fixtures the pin streamlines routine measurements and contributes to predictable process capability. Traceability, identification and procurement certainty Identification is straightforward: SKU M323.J21 and GTIN 4061905071829 ensure unambiguous ordering and stock control. The product is listed in the Messstifte category and conforms to industry expectations for gauge pins used in end‑measure verification. Having clearly documented part numbers accelerates reordering and inventory management, supporting uninterrupted operations and consistent quality assurance. For reliably repeatable inspections, order the M323.J21 gauge pin from Metav Werkzeuge — contact our consultants at info@metav-werkzeuge.com or +49 2822 7131930 for specification support and fast supply Technical Data Article number: M323.J21 GTIN: 4061905071829 Label: Gauge pin, single, 19.21 mm, length 50 mm Category: Messstifte eClass: 21170231 Facts Diameter: 19.21 mm Length: 50 mm Tolerance: ±0.002 mm Weight: 0.2 kg Special features Workshop version Material: special steel Single pin for end measurement Intended for plug/bore verification FAQ What is the nominal diameter and tolerance of this gauge pin? The pin is specified at 19.21 mm diameter with a tolerance of ±0.002 mm, suitable for precise plug checks and acceptance testing. Which materials is the pin made from and what does that mean for wear? Made from special steel, the pin offers enhanced surface durability and resistance to wear compared with untreated mild steels, which supports consistent measurement performance over time. Is this pin suitable for measuring deep or recessed bores? Yes, the 50 mm length provides reach into recessed bores and through holes while keeping rigidity for repeatable measurements. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
19.22mm Gauge Pin Length 50mm Workshop Finish - Metav IndustryLine
Benefit from the combination of ±0.002 mm dimensional accuracy, a robust special-steel construction and a compact 50 mm length for reliable end‑measure checks; order the gauge pin directly via Metav Werkzeuge or consult our specialists for application advice. gauge pin M323.J22 — single inspection pin, 19.22 mm Ø, 50 mm length (Metav IndustryLine) The gauge pin M323.J22 is a single, hardened inspection pin designed for precise diameter verification and end‑measurement tasks in workshop and inspection environments. Workshop version for robust daily use Diameter 19.22 mm with ±0.002 mm accuracy 50 mm length for compact inspection tasks Made from special steel, delivered in a case Accuracy that secures reproducible inspection results The compact inspection pin delivers a repeatable measurement performance thanks to its ±0.002 mm tolerance, which supports high‑precision checks on finished components. Classified for the micro range (suitable for measurement ranges between 10 and 100 mm), this inspection pin is especially useful where short‑span stiffness and minimal deflection matter. The specified tolerance reduces uncertainty during go/no‑go checks and setting of gauges, helping to maintain traceable outcomes in routine quality control. Small format, big practicality for bench and mobile use With a 19.22 mm diameter and 50 mm overall length, the pin is engineered for bench inspection, fixture checking and portable tool sets. The short length keeps bending minimal and makes handling straightforward during serial checks or spot inspections. Supplied as a single piece in a protective case, the pin is convenient for storage and transport between shop floor and inspection bench, helping to speed up workflow without compromising accuracy. Workshop‑grade construction for everyday reliability Constructed from special steel and specified as a workshop version, this inspection pin copes with the rigours of daily use while keeping measurement integrity. The robust material choice and finish make the component resistant to wear in typical workshop applications, ensuring consistent performance over time. Integration into standard inspection routines is uncomplicated, and the pin serves as a dependable reference for end‑measurement tasks and setting operations. Choose the Metav IndustryLine gauge pin for reliable end‑measure verification and contact Metav Werkzeuge in Emmerich for technical clarification or to arrange supply via info@metav-werkzeuge.com or +49 2822 7131930 Technical data SKU: M323.J22 GTIN: 4061905072260 Manufacturer: Metav IndustryLine Facts Diameter: 19.22 mm Length: 50 mm Accuracy: ±0.002 mm Weight: 0.2 kg Special features Workshop design Material: special steel Single inspection pin Delivered in a transport case Category: gauge pins FAQ What tolerance can be expected from this inspection pin? The inspection pin is manufactured and specified with an accuracy of ±0.002 mm, providing high repeatability for diameter checks. Is the pin suitable for portable inspection kits? Yes. With a 50 mm length and compact diameter, the pin fits portable kits and is supplied in a protective case for transport. Can this pin be used for end‑measure verification on finished parts? The gauge pin is designed for end‑measurement and setting tasks; its workshop construction supports routine checks on finished components. What material is the pin made from and how does that affect wear resistance? The pin is made from special steel, chosen for durability in workshop applications to maintain measurement integrity over repeated use. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
Fast, tactile checks where electronics are impractical
Gauges and test pins provide unequivocal go/no-go results for threads, bores, gaps and radii without relying on electronics. The range covers plug gauges and ring gauges for internal and external threads, feeler gauges and precision feeler strips for micro‑gap assessment, plus probe pins and measuring pins for tactile diameter and pitch checks.
How these tools work in the production environment
Mechanical gauges operate as direct reference standards: a plug gauge or ring gauge verifies conformity to thread profiles and mating ability, while limit gauges separate accept from reject in a single step. Test pins are used to tactilely measure small bore diameters, centre‑to‑centre distances and radii. Manufactured from hardened gauge steel or ceramic and often precision lapped, these instruments deliver immediate physical results that are ideal for incoming inspection, machine‑side checks and final control.
Measurable benefits that affect production performance
- Reduced scrap and rework through rapid, unambiguous pass/fail assessment.
- Increased repeatability thanks to very low measurement uncertainty and fine lapping.
- Lower downtime: quick checks at the machine save cycle time and reduce setup periods.
- Durable construction with high wear resistance from specialised, low‑distortion alloys.
- Versatile delivery formats: individual gauges, organised sets in wooden cases or metre‑length feeler rolls compliant with DIN 2269.
Why Metav is the practical choice for precision supplies
Metav combines decades of expertise with a broad warehouse and quality filtering from Emmerich. As a precision partner for industry, craft and trade, Metav supplies a comprehensive selection of gauges and test pins alongside complementary tools such as precision calipers and setting rings. With over 48,000 customers and a catalogue exceeding 250,000 items, Metav is positioned to supply reliably, reduce vendor complexity and support traceable quality control to national standards.
Summary
Gauges and test pins are indispensable for dependable, repeatable quality assurance where tactile, mechanical verification is preferred. Choose these plug gauges, ring gauges, feeler strips and probe pins when immediate, robust measurement decisions are required on the shop floor.
FAQ
What materials are gauges and test pins typically made from?
Gauges and test pins are usually manufactured from hardened gauge steel for durability and wear resistance; ceramic variants are available where thermal stability and minimal wear are critical.
How do thread gauges ensure mating capability?
Thread plug gauges and ring gauges check flank diameters and thread form against standards, providing a clear go/no‑go verdict that confirms pairability with mating parts.
Which tolerance class should I choose for probe pins and gauge sets?
Select tolerance classes aligned with your inspection requirements; for high‑precision tasks, sets produced to DIN 2269 or equivalent tolerance classes ensure micrometre‑level control and repeatability.
Can feeler gauges measure contact gaps in valve and engine work reliably?
Yes. Feeler gauges and precision feeler strips, supplied either as a fan or metre‑length rolls, allow accurate assessment of valve clearances and contact gaps down to micrometre increments.
How do limit gauges speed up in‑process inspection?
Limit gauges separate good from bad in a single, tactile operation, enabling rapid go/no‑go checks at the machine and reducing both inspection time and the likelihood of human interpretation errors.
Fragen zu diesen Produkten??
Mit mehr als 30 Jahren Erfahrung beraten wir Sie gerne persönlich.
Tel.: +49 2822 7131930
Mail: info@metav-werkzeuge.com