Precision gauge blocks and plug gauges for reliable dimensional control
Mechanical gauge blocks and plug gauges are essential for tactile verification of threads, bores and gap dimensions, providing fast, unambiguous go/no-go results that enhance process reliability and reduce scrap. Designed for industrial metalworking and toolmaking, these precision tools support incoming inspection and final quality checks by delivering traceable measurements in applications such as thread inspection, bore diameter testing and spacing checks. Manufactured from specially hardened, low-distortion alloys and fine-lapped for minimal measurement uncertainty, the range includes thread plug gauges, precision plug gauges and calibration gauge blocks to ensure long-term repeatability and wear resistance.
19.71mm Test Pin Single 50mm Length Workshop Finish - Metav IndustryLine
Benefit from workshop-grade reliability with a 19.71 mm diameter measuring pin finished from special steel, manufactured to a tolerance of ±0.002 mm for repeatable end-measure checks and fixture alignment; ordering and technical advice are available through Metav Werkzeuge or via consultation with our product specialists. Order the gauge pin directly via Metav Werkzeuge or ask our consultants if needed. Gauge pin, single, 19.71 mm diameter, 50 mm length — Metav IndustryLine workshop version The gauge pin, single, 19.71 mm is a workshop-grade verification pin for end-measure checks and alignment tasks in general machining and assembly applications. Workshop-grade construction Diameter 19.71 mm precision Tolerance ±0.002 mm Special steel for wear resistance Precision for repeatable end measurements The pin is engineered to deliver consistent repeatability in end-measure verification. With a nominal diameter of 19.71 mm and a stated accuracy of ±0.002 mm, the component provides a narrow tolerance band that helps reduce measurement uncertainty and rework in production. The narrow tolerance is especially beneficial when checking bore seats, dowel fits or plug gauges where dimensional conformity directly affects assembly behaviour. The special steel composition provides a stable datum under typical workshop conditions, ensuring the measured interface remains representative over repeated use. Robust workshop design that keeps measuring reliable A length of 50 mm offers sufficient engagement for many practical inspection and alignment tasks while remaining easy to handle in a busy workshop. The workshop execution designation indicates a design that balances stiffness and wear resistance for everyday usage, rather than fragile laboratory handling. The mass and geometry are chosen to be compatible with common measuring fixtures and bench tools, and the single-pin format simplifies inventory and replacement procedures. This format supports efficient inline checks and helps maintain throughput without compromising the traceability of critical dimensions. Practical integration into inspection routines and fixtures The single gauge pin integrates directly into fixture set-up, go/no-go checks and comparative measurement jigs. Its compact form factor suits bench top toolrooms and assembly stations where space and accessibility are at a premium. When used as an end-measure reference, the pin reduces the need for complex setups and can be combined with alternative reference pins for stepwise validation. For traceable recording, the pin’s clearly defined diameter and tolerance allow straightforward documentation in inspection reports and work instructions, supporting consistent quality control across shifts and operators. Contact Metav Werkzeuge in Emmerich for tailored application advice and stock availability of the Metav IndustryLine gauge pin M323.J71 Technical Data Article number: M323.J71 GTIN: 4061905449703 Brand: Metav IndustryLine ECLASS: 21170231 Facts Diameter: 19.71 mm Length: 50 mm Tolerance: ±0.002 mm Weight: 0.2 kg Special features Material: special steel Workshop execution Single gauge pin Intended for end-measure checks FAQ What is the declared tolerance for this gauge pin? The declared tolerance for the Metav IndustryLine gauge pin M323.J71 is ±0.002 mm, suitable for precise end-measure verification. Is the item supplied individually or as part of a set? This entry describes a single gauge pin supplied individually under the Metav IndustryLine designation. Which material is used for the pin? The pin is made from special steel, selected for durability and stable contact behaviour in workshop conditions. For which tasks is this gauge pin suitable? The pin is intended for end-measure checks, fixture alignment and plug-like verification in machining and assembly operations. How is the pin identified for ordering and documentation? Use the article number M323.J71 and GTIN 4061905449703 when ordering or recording the component in inspection documentation. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
19.72mm Test Pin Workshop Version, 50mm Length - Metav IndustryLine
Take advantage of the combination of workshop-grade durability, tight dimensional tolerance and compact handling for reliable end‑dimension checks; order the gauge pin directly via Metav Werkzeuge or contact the team for application advice. Gauge pin, single, 19.72 mm (50 mm length) – Metav IndustryLine The gauge pin, single, 19.72 mm, length 50 mm is a precision checking pin designed for end‑dimension verification and plug checks in workshop inspection and small‑series production. Workshop version for robust daily use Diameter 19.72 mm for end‑dimension checks Made from special steel for long service life Dimensional tolerance ±0.002 mm precision Consistent accuracy for routine inspection This checking pin delivers consistent accuracy with a stated dimensional tolerance of ±0.002 mm, making it suitable for tight control tasks in a busy inspection bench. The closely held tolerance reduces rework by ensuring that the checked bore or shaft mates to the intended end dimensions; where repeatability matters, the pin provides a reliable reference for go/no‑go procedures and manual inspection routines. The compact format helps keep cycle times low while maintaining measurement integrity. Robust construction for workshop environments Manufactured in a workshop version and from special steel, the pin is engineered for daily handling and frequent use without rapid wear. The 50 mm length offers secure gripping during insertion and withdrawal yet remains short enough to avoid undue bending or user fatigue. The material choice balances hardness and surface finish to preserve the nominal diameter under normal workshop conditions, supporting longer service life and fewer replacements. Practical handling and inspection use As a single gauge pin, the component is intended for direct use in end‑dimension checks, alignment aids and simple fit tests. The 19.72 mm diameter is presented as a precise reference size for matching bores or shafts; paired with visual inspection or a simple comparator, the pin simplifies pass/fail decisions on the shop floor. Lightweight at approx. 0.20 kg, it is easy to manipulate during repeated checks and integrates well with existing inspection tooling and gauges. Trusted supply and workshop support Delivered under the Metav IndustryLine banner, this checking pin benefits from a supplier network focused on accessibility and dependable logistics. Metav’s experience in equipping workshops ensures consistent availability and a pragmatic selection of standardised inspection items. The product suits workshop technicians and small quality departments that prioritise straightforward, durable measuring aids over elaborate fixtures. For reliable workshop inspection components and tailored advice on how this Metav IndustryLine gauge pin can fit into existing measurement routines, contact Metav Werkzeuge in Emmerich for direct assistance and supply coordination. Technical data Article number: M323.J72 GTIN: 4061905450006 Manufacturer: Metav IndustryLine Facts Diameter: 19.72 mm Length: 50 mm Weight: 0.20 kg Dimensional tolerance: ±0.002 mm Special features Material: special steel Version: workshop execution Delivery form: single gauge pin Category: gauge pins (Messstifte) FAQ What measurement accuracy can be expected from this checking pin? The checking pin offers a dimensional tolerance of ±0.002 mm, suitable for precise end‑dimension checks and consistent go/no‑go assessments. Is the pin suitable for regular workshop use? Yes; the workshop version construction and special steel material make the pin robust for frequent handling and routine inspection tasks. Can the pin be used to check bore diameters? The pin’s nominal diameter of 19.72 mm is appropriate for manual verification of bore fits and end‑dimension checks where a fixed reference gauge is required. How should the pin be stored to maintain accuracy? Store the pin clean and dry, ideally in a protected tray or drawer to avoid knocks and contamination; regular visual checks for surface damage will help preserve dimensional integrity. Which catalogue reference identifies this product for reorders? This item is available as M323.J72 under the Metav IndustryLine range and listed with GTIN 4061905450006. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
19.73mm Test Pin, Single, 50mm Length, Workshop Version - Metav IndustryLine
Take advantage of the combination of high repeatability (±0.002 mm), durable special steel construction and a compact 50 mm length for straightforward end-dimension checks. Order the test pin directly via Metav Werkzeuge or request advice from our consultants for integration into existing inspection routines. Test pin, single — 19.73 mm diameter, 50 mm length (Metav IndustryLine) A single test pin designed for precise end-measurements and workshop use, optimised for go/no-go checks and fixture set-ups. Precision tolerance ±0.002 mm Exact diameter 19.73 mm 50 mm overall length, workshop grade Made from special steel for durability Reliable measurement where traceability counts The inspection probe delivers a measured tolerance of ±0.002 mm, making it suitable for fine gauging tasks and repeat checks in production and quality control. The externally defined 19.73 mm diameter provides a clear nominal reference for end-dimension inspection, while the compact 50 mm overall length supports use in confined fixtures. Built to reduce measurement variation, the component assists in establishing consistent acceptance criteria on small runs and series production. The material choice of special steel contributes to dimensional stability and wear resistance, translating directly into fewer re-measurements and less downtime. Built for frequent workshop use and straightforward handling This workshop-grade inspection pin is a practical solution for toolrooms and assembly benches where robustness and ease of use matter. The single-piece construction minimises joints and tolerances that could introduce error; the relatively low mass improves handling during repetitive tasks. As a dedicated gauging element, the item integrates well with bench fixtures, comparator stands and simple jigs, enabling rapid go/no-go decisions without complex set-up. The result is faster throughput for routine checks and a reduced risk of measurement-related production delays. Integration into inspection workflows and stock management Designed as a standardised gauging component, the pin is convenient to catalogue and store as part of a core inspection kit. The clear nominal diameter and tolerance support documentation in inspection reports and drawings, and the robust construction reduces the need for frequent replacement. For procurement and supply-chain planning, the part is supplied under the SKU shown below and is compatible with common bench equipment used in small-batch manufacturing and maintenance shops. Metav IndustryLine’s presence in Europe ensures predictable availability and a local quality filter for reliable deliveries. For supply, compatibility checks or to discuss batch requirements, contact Metav Werkzeuge GmbH — Metav IndustryLine is available through Metav’s consultants at info@metav-werkzeuge.com or by phone on +49 2822 7131930 Technical data Article number: M323.J73 SKU: M323.J73 GTIN: 4061905450013 ECLASS: 21170231 Core specifications Nominal diameter: 19.73 mm Overall length: 50 mm Permissible deviation: ±0.002 mm Weight: 0.2 kg Materials & special features Material: Special steel Workshop version Single test pin for end-dimension checks Storytrigger: end dimensions (endmasse) FAQ What tolerance can be expected from this test pin? The test pin is specified with a tolerance of ±0.002 mm, providing high repeatability for end-dimension checks with the Metav IndustryLine item M323.J73. Which materials is this pin suitable for inspecting? The pin is a gauging element for dimensional checks and can be used to verify finished geometry across a range of materials; its special steel construction ensures durability during repeated contact inspections. Is this pin intended for fixture or handheld use? The workshop-grade design suits both fixture-mounted use and manual inspection routines; the compact 50 mm length aids handling in confined setups without compromising stiffness. How is the product identified for ordering and inventory? The part is listed under SKU M323.J73 and GTIN 4061905450013 for reliable procurement and stock control. Can this pin be used for reference measurements in quality documentation? Yes, the clear nominal diameter of 19.73 mm and the stated tolerance make the component appropriate as a reference element in inspection records and quality reports. Metav IndustryLine: Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
19.74mm Gauge Pin 50mm Length Workshop Version - Metav IndustryLine
Combine workshop‑grade robustness with high repeatability: ±0.002 mm tolerance and a compact Ø19.74 mm / 50 mm form make this gauge pin ideal for precise end‑of‑line checks and plug‑gauging. Order the gauge pin directly via Metav Werkzeuge or consult our advisors for application support. Gauge pin M323.J74 — single gauge pin, Ø19.74 mm, 50 mm length (Metav IndustryLine) The single gauge pin Ø19.74 mm, length 50 mm is a workshop‑grade reference pin for precise diameter verification, plug gauging and fixture checking in micro‑precision tasks Single gauge pin Ø19.74 mm Tolerance ±0.002 mm 50 mm length in special steel Delivered in a transport case Accurate checks for tight tolerances The compact design delivers consistent precision where small deviations matter. With a manufacturing tolerance of ±0.002 mm, the pin supports reproducible diameter verification and plug‑gauging operations in assembly and inspection workflows. The short overall length helps to keep bending and runout to a minimum, which translates into reliable comparative measurements during quick pass/fail checks or when setting up inspection fixtures. The robust dimensions suit batch inspection and intermittent in‑process control, improving throughput by reducing retest rates. Built for workshop handling and long‑term repeatability Made from special steel in a workshop version finish, the pin stands up to daily handling and routine throughput checks. The material choice balances wear resistance and machinability, providing a stable contact geometry across repeated use. Delivered in a transport case, the pin is protected during storage and transport, preserving the measurement surface and ensuring traceable reference conditions for longer service life. The practical weight and compact length simplify integration into pin sets or jigs without adding handling complexity. Micro class precision for small‑bore and fine‑mechanical tasks Classified in the micro measurement range, this gauge pin is suited to fine‑mechanical and precision engineering applications where compact gauges are required. The geometry and tolerance level make it appropriate for small‑bore verification, alignment of mating parts and pre‑assembly inspection of components where clearance margins are minimal. Where high repeatability is a priority, the pin provides a stable reference that reduces uncertainty in comparative checks and setup routines. Practical compatibility and confidence in results The straightforward cylindrical form is compatible with standard plug‑gauging fixtures and slip‑fit checks. As a single, well‑specified reference element from Metav IndustryLine, it offers a simple way to raise inspection confidence without overcomplicating the measurement process. The clear specification supports traceable records and makes the pin a dependable element for quality documentation in workshop and production environments. For workshop‑grade precision and reliable traceability, contact Metav Werkzeuge in Emmerich for advice on the Metav IndustryLine gauge pin M323.J74 or to place an order: info@metav-werkzeuge.com / +49 2822 7131930 Technical data SKU: M323.J74 GTIN: 4061905450020 Brand: Metav IndustryLine Category: Gauge pin (single) Special version: Workshop execution Diameter: 19.74 mm Length: 50 mm Tolerance: ±0.002 mm Weight: 0.2 kg Material: Special steel Delivered in transport case Intended use: Diameter verification, plug gauging, fixture checking Feature: Compact micro‑range reference pin FAQ What is the intended use of this gauge pin? The gauge pin M323.J74 is intended for diameter verification, plug‑gauging and fixture checks in micro‑precision and workshop applications. Is the accuracy of the pin suitable for fine mechanical work? Yes, the ±0.002 mm tolerance makes this pin suitable for fine mechanical tasks where tight diameter control is required. How is the gauge pin packaged for transport? The pin is supplied in a transport case to protect the measurement surface during storage and transport. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
19.75mm Gauge Pin, Single, 50mm Length, Workshop Version - Metav IndustryLine
Take advantage of the combination of high metrological precision, robust special‑steel construction and practical transport packaging for dependable end‑measurement routines; the 19.75 mm diameter and ±0.002 mm tolerance make this an accurate reference for workshop checks. Order the (gauge pin) directly via (Metav Werkzeuge) or ask our consultants if needed. Gauge pin, single — 19.75 mm Ø, 50 mm length (Metav IndustryLine) The Gauge pin, single — 19.75 mm Ø is a precision ground reference pin designed for end‑measure checks and go/no‑go verification in workshop and inspection applications. Workshop version for robust everyday use Diameter 19.75 mm with tolerance ±0.002 mm Length 50 mm for secure seating and handling Supplied in a protective transport case Precision that secures inspection results The reference pin is manufactured for repeatable end‑measure verification, offering a ground diameter of 19.75 mm with a declared concentricity and finish that supports the specified ±0.002 mm variation. Such dimensional stability is suitable for high‑precision workshop tasks where small deviations translate into assembly problems; the tight tolerance reduces uncertainty during go/no‑go checks and complements optical or tactile comparators. The compact design facilitates accurate seating in jigs and fixtures, making it a reliable datum element in daily measurement routines. Built for workshop use and reliable handling As a workshop version, the component uses special steel chosen for wear resistance and easy maintenance under frequent handling. The 50 mm length provides a positive grip and correct engagement depth in fixtures while remaining compact enough for fast repositioning. Delivery in a transport case (plastic or wooden) protects the gauge during storage and transit; this packaging is intended for secure transport rather than long‑term archival storage. The single‑piece format is optimised for direct insertion and visual inspection, supporting efficient process control on the shop floor. Integration into quality workflows and supplier trust Metav IndustryLine supplies this reference pin as part of a broader precision portfolio, enabling consistent sourcing and traceability for workshop metrology. The component's dimensional data and workshop execution make it straightforward to incorporate into routine inspection steps or simple fixture checks. Where traceable calibration is required, consult Metav Werkzeuge for options; the product's design supports straightforward documentation of measurement results and enhances confidence in final assembly checks. Choosing established components from a dedicated precision partner reduces procurement complexity and supports continuous production quality. Choose the Metav IndustryLine gauge for dependable end‑measurement control and contact Metav Werkzeuge in Emmerich for application advice or to request a supply. Technical data Article number: M323.J75 GTIN: 4061905071928 Manufacturer: Metav IndustryLine Facts Diameter: 19.75 mm Length: 50 mm Weight: 0.2 kg Tolerance: ±0.002 mm Special features Workshop execution Material: special steel Supplied in transport case (plastic or wooden) Single piece for end‑measure checks Application hint: end measurements FAQ What is the declared dimensional tolerance of this gauge? The gauge pin is specified with a dimensional variation of ±0.002 mm for the 19.75 mm diameter. Is the transport case suitable for long‑term storage? The transport case supplied with the M323.J75 protects the pin during transport and short‑term storage; it is intended primarily as transport packing rather than a long‑term storage container. Can this pin be used as a reference in fixtures for assembly checks? Yes, the 50 mm length and ground diameter make the pin suitable as a datum or reference element in fixtures for go/no‑go and end‑measurement tasks. Which material is used and how does it affect wear? The pin is made from special steel selected for workshop durability; the material provides good wear resistance under normal handling and inspection conditions. Is the M323.J75 available calibrated on delivery? Calibration options can be discussed with Metav Werkzeuge; the standard supply includes the product and transport packaging, and calibration services are available on request. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
19.76mm Test Pin 50mm Length Workshop Version Supplied In Case - Metav IndustryLine
Take advantage of the combination of high positional accuracy (±0.002 mm), durable special steel construction and a compact 50 mm length for reliable end‑measure checks; order the single gauge pin directly via Metav Werkzeuge or consult the team for application advice. Gauge pin, single — 19.76 mm diameter, 50 mm length (Metav IndustryLine) The gauge pin, single, 19.76 mm, 50 mm length is a workshop‑grade reference pin designed for precise end‑measurement and dimensional verification in inspection and assembly environments. High positional accuracy ±0.002 mm Durable special steel construction Workshop‑grade finish with protective case Single piece, ready for immediate use Precision that makes inspection faster and more reliable The compact reference pin delivers repeatable results thanks to its ±0.002 mm accuracy and a nominal diameter of 19.76 mm, reducing uncertainty in repetitive end‑measure checks. As a single, purpose‑made test pin it shortens setup time for gauging tasks and eliminates the need for time‑consuming adjustments. The combination of a defined nominal size and tight tolerance supports faster decisions in quality control routines and contributes directly to improved throughput on the inspection bench. Built for everyday workshop handling and durability Specified as a workshop‑grade item and made from special steel, the pin tolerates routine handling while keeping surface integrity and dimensional stability. The 50 mm length gives sufficient engagement for most end‑measure and fit checks without becoming cumbersome, and the supplied protective case ensures safe transport and storage. These design choices lower the long‑term cost of ownership by protecting the reference surface and maintaining measurement confidence between calibrations. A traceable, single‑piece reference for end‑measurement Delivered as an individual gauge pin, the product is ideal when a single, clearly defined reference diameter is needed for end‑dimension verification or final fitting operations. The item is lightweight yet substantial in feel, aiding ergonomic use during rapid inspection cycles. For procurement and traceability the pin is listed under SKU M323.J76 and carries a GTIN for inventory systems, making it straightforward to document and reorder the exact reference part required for consistent quality checks. Contact Metav Werkzeuge for ordering and application advice on the M323.J76 gauge pin; the Emmerich team will recommend the correct solution and arrange delivery to the workshop Technical Data SKU: M323.J76 GTIN: 4061905071935 ECLASS: 21170231 Label: Prüfstift, einzeln, 19,76 mm Länge 50 mm Facts Diameter: 19.76 mm Length: 50 mm Accuracy: ±0.002 mm Weight: 0.2 kg Special features Material: special steel Workshop‑grade execution Supplied in a protective case Single piece delivery FAQ What tolerance can be expected from this gauge pin? The gauge pin is manufactured to an accuracy of ±0.002 mm, providing tight repeatability suitable for precise end‑measurement tasks. Is the pin supplied calibrated? This product is supplied as a single gauge pin; calibration status is not specified in the basic data set. For calibrated variants or calibration certificates, please request details when ordering the M323.J76 from Metav Werkzeuge. Which applications is this pin intended for? The pin serves as a reference for end‑measure checks, fit verification and dimensional control in workshop and inspection settings where a single, precisely defined diameter is required. What is the construction material and how does it affect durability? Constructed from special steel, the pin balances wear resistance and dimensional stability to withstand routine handling in the workshop. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
19.77mm Plug Gauge Test Pin 50mm Length Workshop Version - Metav IndustryLine
Take advantage of high repeatability and the tight geometric tolerance for reliable end‑of‑line checks; the compact 19.77 mm diameter with a ±0.002 mm tolerance and a 50 mm shank ensures consistent fit checks and reference measurements in workshop environments. Order the gauge pin directly via Metav Werkzeuge or ask the consultants for batch supply and application advice. M323.J77 gauge pin — 19.77 mm diameter, 50 mm length (Metav IndustryLine) The M323.J77 is a single precision gauge pin designed for end‑measure checks and bore verification, offering a workshop‑grade configuration for everyday inspection tasks Diameter 19.77 mm with ±0.002 mm tolerance 50 mm overall length in workshop execution Manufactured from special steel for wear resistance Single piece delivery for individual verification Consistent, measurable accuracy for bore validation Built for repeatable inspection cycles, this gage delivers a 19.77 mm reference with a certified ±0.002 mm positional tolerance, making it suitable where dimensional fidelity matters. The specified tolerance indicates the maximum permissible deviation from nominal diameter and supports reliable go/no‑go assessments and reference checks. Operators benefit from faster decision making during batch inspections because the tight tolerance reduces ambiguity when verifying bore sizes, while the compact form ensures compatibility with common fixture layouts. Robust design that suits everyday workshop use The workshop‑oriented configuration pairs a short, rigid shank with special steel construction to resist wear and preserve geometry under frequent handling. A 50 mm shank provides enough engagement for stable insertion while remaining manoeuvrable in confined set‑ups; the combination of length and material promotes long service life and repeatable seating in jigs and fixtures. The single‑piece supply simplifies traceability for individual items used as master references in sampling plans or setting tools in production. Integrates into quality workflows and purchasing processes With an industry‑recognised SKU and GTIN for inventory control, the gage supports ordered workflows and clear labelling in stores and inspection reports. The compact profile and proven tolerance make it a practical solution for machine shops, toolrooms and inspection benches where small‑batch validation or final checks are required. Metav IndustryLine’s offering aligns with the company’s focus on making precise metrology accessible: dependable stock, clear product data and the option to consult specialists help reduce procurement risk and maintain throughput in production environments. Contact Metav Werkzeuge to discuss supply options for the M323.J77 and secure workshop‑grade gauge pins for reliable bore inspection. Technical data Article number: M323.J77 GTIN: 4061905071942 SKU: M323.J77 Label: Prüfstift, einzeln, 19,77 mm Länge 50 mm Facts Diameter: 19.77 mm Length: 50 mm Tolerance: ±0.002 mm Weight: 0.2 kg Special features Material: Special steel Version: Workshop execution Delivery: single piece FAQ What is the intended use of this gauge pin? The M323.J77 gauge pin is intended for precise bore verification and end‑measure checks where a 19.77 mm datum is required for go/no‑go decisions. How tight is the manufacturing tolerance? Tolerance is specified as ±0.002 mm, enabling precise comparative measurements and repeatable fit testing in production and inspection tasks. Can this pin be used for master setting of fixtures? Yes; the combination of a 50 mm shank and wear‑resistant special steel makes it suitable as a reference for fixture set‑up and repeatable seating. Is the gauge suitable for frequent workshop handling? The workshop execution and robust material selection are geared towards regular use, maintaining geometry over repeated insertion cycles. How is traceability handled for individual parts? Each item is supplied as a single piece with SKU and GTIN for inventory tracking; Metav IndustryLine supports additional documentation upon request. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
19.78mm Test Pin 50mm Length Workshop Version, Hardened Special Steel - Metav IndustryLine
Reliable inspection results from a compact, durable tool: high repeatability with a ±0.002 mm tolerance combined with a 19.78 mm diameter and 50 mm length in workshop‑grade construction. Order the item directly via Metav Werkzeuge or ask our consultants for tailored advice. Single gauge pin M323.J78 – Single gauge pin, Ø 19.78 mm, length 50 mm (Metav IndustryLine) A single gauge pin (19.78 mm, 50 mm length) engineered for precise end‑dimension checks, fixturing verification and go/no‑go fitting tasks in workshop and inspection environments. *Single gauge pin Ø 19.78 mm, 50 mm length *High‑precision tolerance ±0.002 mm *Made from special steel, workshop execution *Delivered in protective transport case Reliable dimensional control for production and inspection This compact inspection pin delivers reproducible checks where tight end dimensions are mandatory. With a nominal diameter of 19.78 mm and an accuracy class down to ±0.002 mm, the pin is suitable for repeat measurements, run‑out verification and plug‑fit tests that feed directly into quality decisions. The controlled geometry reduces uncertainty in go/no‑go assessments and supports faster inspection cycles, which helps to reduce rework and throughput delays. Durable workshop construction that stays accurate Manufactured from special steel in a workshop‑grade finish, the component resists typical workshop wear and preserves functional dimensions over repeated use. The 50 mm shank provides stable handling on fixtures and in measuring jigs while the moderate mass (approx. 0.2 kg) aids in secure placement without excessive handling fatigue. Delivered in a protective transport case, the pin arrives ready for safe storage and transport between workstations or to inspection benches. Practical benefits for inventory and process reliability Identified as M323.J78, the pin is easy to catalogue and replace within maintenance and metrology workflows. The compact form factor minimises storage space yet aligns with standard handling routines for end‑dimension verification and fixture set‑up. Using a standardised gauge pin like this supports predictable assembly checks and helps to streamline incoming inspection and in‑process control, improving overall plant efficiency and measurement reproducibility. Choose the Metav IndustryLine M323.J78 for dependable end‑dimension checks — contact Metav Werkzeuge GmbH in Emmerich for ordering and product guidance at info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: M323.J78 GTIN: 4061905071959 Label: Prüfstift, einzeln, 19,78 mm Länge 50 mm Core specifications Diameter: 19.78 mm Length: 50 mm Tolerance: ±0.002 mm Weight: 0.2 kg Materials & features Material: Special steel Version: Workshop execution Delivery: Protective transport case Application: End‑dimension inspection FAQ What tolerance can be expected from this gauge pin? The gauge pin offers a tolerance of ±0.002 mm, making the M323.J78 suitable for high‑accuracy end‑dimension checks and precise plug‑fit verifications. Which material is used for the pin and how robust is it? The pin is made from special steel in a workshop execution, providing wear resistance and dimensional stability for routine inspection tasks. Is the pin suitable for go/no‑go and fixture checks? Yes — the geometry and tight tolerance make the pin well suited for go/no‑go fittings, fixture alignment and plug‑fit testing in production and assembly. How is the item supplied for transport and storage? The item is supplied in a protective transport case to safeguard the measuring surface during transport and storage. How should the pin be referenced in inventory systems? Reference the item by its article number M323.J78 and GTIN 4061905071959 for unambiguous identification in procurement and spare‑parts lists. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
19.79mm Gauge Pin 50mm Length Workshop Version - Metav IndustryLine
Take advantage of workshop-proven robustness and high metrological accuracy: the combination of special steel construction, a tight ±0.002 mm tolerance and a compact 50 mm length ensures repeatable bore checks and fit verification. Order the gauge pin directly via Metav Werkzeuge or consult our specialists for application advice. Gauge pin, single – 19.79 mm diameter, 50 mm length (Metav IndustryLine) The Gauge pin, single (19.79 mm, 50 mm) is a workshop-grade inspection pin engineered for precise bore gauging, fit verification and dimension control in production and maintenance environments Workshop-grade construction for everyday use Special steel for wear resistance Tolerance ±0.002 mm for reliable inspection Supplied in protective case for secure transport Improve inspection certainty with micrometric tolerance A compact inspection dowel with a nominal diameter of 19.79 mm and a declared tolerance of ±0.002 mm delivers a measurable improvement in pass/fail decisions during routine checks. The fine tolerance reduces the risk of false rejects and minimizes downstream rework, while the short 50 mm length keeps the pin rigid during insertion. Specifying a narrow tolerance is a rational choice when process reproducibility and traceable results are priorities. Designed for workshop conditions and consistent handling The workshop-grade design emphasises durability under frequent use: manufactured from special steel, the pin resists surface wear and preserves cylindrical form over many cycles. The robust material choice supports repeat measurements and lowers the total cost of ownership by extending service life. In practice, this means fewer calibration interventions and a dependable tool for maintenance, bench checks and assembly stations. Practical storage and transport for everyday use Delivered as a single piece in a protective case, the pin is ready for safe storage and simple transport between inspection benches. The packaging reduces the chance of surface marks that compromise gauge performance and supports organised tool handling in busy workshops. The compact footprint and clear labelling simplify inventory management and make the pin straightforward to integrate into existing inspection kits. Typical applications and compatibility with inspection setups This inspection pin suits bore gauging, press-fit checks and go/no-go verifications on small to medium components. The combination of nominal diameter, length and material makes it appropriate for general metalworking, tooling checks and quality control stations. Where a compact, repeatable reference is required for assembly verification or tool setup, the pin provides a pragmatic metrological solution without the complexity of larger gauge systems. Contact Metav Werkzeuge for detailed specification advice or to confirm current stock and delivery for the M323.J79 gauge pin with 19.79 mm diameter Technical Data Article number: M323.J79 GTIN: 4061905072444 Manufacturer: Metav IndustryLine Facts Nominal diameter: 19.79 mm Length: 50 mm Tolerance: ±0.002 mm Weight: 0.2 kg Special features Workshop-version design Material: special steel Supplied single in protective case Intended for bore gauging and fit verification FAQ What is the declared tolerance of this gauge pin? The gauge pin is specified with a ±0.002 mm tolerance, ensuring precise pass/fail decisions during bore and fit inspections. Is the pin suitable for continuous workshop use? Yes, the Metav IndustryLine workshop-version pin is made from special steel and designed for frequent handling and repeated checks. What are the typical applications for a 19.79 mm pin? Common uses include bore gauging, press-fit verification and tooling checks where a compact, repeatable reference of 19.79 mm is required. How is the pin supplied and protected for transport? The pin is supplied individually in a protective case to prevent surface damage and to facilitate organised storage and transport. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
19.7mm Test Pin, Single, 50mm Length, Workshop Version - Metav IndustryLine
Benefit from a workshop-grade gauge pin that combines exact nominal sizing, a tight ±0.002 mm tolerance and robust special-steel construction for dependable inspection results; order the test pin directly via Metav Werkzeuge or consult the Metav team for application advice. Test Pin, single, 19.7 mm – Gauge pin, 50 mm length (Metav IndustryLine) A Test Pin, single, 19.7 mm engineered for precise nominal-diameter verification in workshop and inspection environments. Ø 19.7 mm nominal size for tight tolerances 50 mm length for secure handling and grip Special-steel construction, workshop finish Precision where measurement matters This single gauge pin delivers consistent dimensional control for diameter verification and end-measure tasks. With a nominal size of 19.7 mm and a verified tolerance of ±0.002 mm, it supports quality checks where repeatable accuracy is essential. The compact format is suited to inline inspection, go/no-go gauging and manual comparators; the measured value is directly comparable to drawing tolerances, reducing ambiguity in acceptance decisions and improving throughput in inspection processes. Robust design for workshop environments Manufactured from special steel with a workshop-grade finish, the pin is designed for frequent handling and practical use at production benches. The 50 mm length offers a comfortable grip and enough engagement for stable seating in fixtures or test blocks, while the moderate mass (approx. 0.2 kg) aids controlled placement during measurement. The single-piece format minimises play and simplifies inventory for common nominal sizes, helping maintain an organised inspection kit. Practical integration and traceable identification The pin is supplied as an individual test item suitable for standard comparator stands and handheld verification tools used in industrial metrology. Markings and traceable identifiers are provided to aid part selection and stock management; the compact form factor eases storage and rapid deployment during batch checks. For systematic quality control, the pin complements existing gauge sets and supports a structured inspection routine that shortens decision cycles and documents conformity. Contact Metav Werkzeuge to secure this Metav IndustryLine gauge pin and request tailored advice for integrating workshop-grade nominal-size pins into existing inspection procedures Technical Data SKU: M323.J70 GTIN: 4061905449697 Category: Gauge pin Facts Diameter: 19.7 mm Length: 50 mm Weight: 0.2 kg Tolerance: ±0.002 mm Special features Material: Special steel Workshop version Single test pin Nominal size 19.7 mm FAQ What nominal size does this gauge pin check? The gauge pin checks a nominal diameter of 19.7 mm and is produced as a single test pin for direct diameter verification. What is the declared tolerance of the pin? The declared dimensional tolerance for this test pin is ±0.002 mm, making it suitable for fine inspection tasks where tight conformity is required. Can the pin be used in comparator fixtures and handheld checks? Yes, the pin’s 50 mm length and workshop finish make it compatible with standard comparator fixtures and manual inspection routines. What material is the pin made from? The pin is made from special steel, providing a durable surface and mechanical stability appropriate for frequent workshop use. How is the item identified for inventory and traceability? The test pin is listed under SKU M323.J70 and GTIN 4061905449697 to support traceability and inventory control. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
19.81mm Gauge Pin 50mm Length Workshop Version, Special Steel - Metav IndustryLine
Take advantage of the combination of exact nominal dimension, workshop-hardened construction and traceable identification for reliable bore checks and end-measure verification. Benefit from a compact, precision component that complements inspection routines and can be ordered directly via Metav Werkzeuge or discussed with our technical consultants. Gauge pin M323.J81 — workshop-grade gauge pin, 19.81 mm Ø, 50 mm length (Metav IndustryLine) The gauge pin M323.J81 is a single precision inspection pin designed for secure verification of bores and fits in workshop inspection and assembly environments. Precision tolerance ±0.002 mm Exact nominal diameter 19.81 mm 50 mm hardened length for stable engagement Workshop-grade special steel construction Reliable checks where tolerance matters The compact inspection pin delivers consistent dimensional reference thanks to its ±0.002 mm manufacturing tolerance and exact 19.81 mm nominal diameter. For workshop quality control this level of precision reduces measurement uncertainty during fit checks and end-measure verification, enabling repeatable go/no-go assessment when used alongside conventional gauging methods. The numeric tolerance is suitable for high-accuracy mechanical assemblies where small deviations can affect assembly or function. Built for frequent handling and shop use Constructed in special steel with a workshop-grade finish, the pin resists wear while preserving its measuring surface. The 50 mm engagement length gives a secure contact area that helps to avoid tilting or partial insertion during inspections. Combined with a modest mass of 0.2 kg, the component balances robustness with manoeuvrability on the bench or in a measuring fixture, reducing handling fatigue during repetitive checks. Fast integration into existing inspection routines As a single inspection element, the component slips into established workflows without additional calibration requirements beyond standard shop practice. Its precise nominal dimension makes it suitable as a reference for plug checks, fixture setting and end‑measure comparison. Where traceable identification is required, the article is listed under the SKU and GTIN for inventory control and process documentation. Traceability and identification for production control Each item is identifiable by its designation and catalogue reference, supporting clear documentation in inspection records and part lists. The combination of a defined nominal size and a tight tolerance supports traceable quality assurance and easier communication between workshop teams and purchasing, helping to standardise bore-verification procedures across shifts and sites. Practical handling advice to preserve accuracy To maintain the specified tolerance, keep measuring surfaces clean and free from burrs or corrosion; avoid forceful impacts that could deform the contact diameter. A gentle wipe and storage in a clean rack minimise contamination and preserve repeatability. The pin’s compact format makes it easy to include in standard tool kits for fixture setup or incoming inspection. Typical applications and compatibility This inspection element is intended for bore and fit control in general machine building, jigs and fixtures, and assembly verification. Its nominal size and tolerance suit fine mechanical assemblies and workshop-level quality control where compact, reliable reference pins are required. Contact Metav Werkzeuge today to order the Metav IndustryLine M323.J81 gauge pin or request application advice from our specialists Technical data Article number: M323.J81 Label: Gauge pin, single, 19.81 mm diameter, 50 mm length GTIN: 4061905072468 Facts Diameter: 19.81 mm Length: 50 mm Tolerance: ±0.002 mm Weight: 0.2 kg Special features Material: special steel Designation: workshop-grade execution Category: Messstifte (gauge pins) Accuracy class: ±0.002 FAQ What is the nominal diameter and tolerance of this gauge pin? The gauge pin has a nominal diameter of 19.81 mm and is manufactured to a tolerance of ±0.002 mm, providing a stable reference for bore verification. Can the M323.J81 be used for fixture setup and assembly checks? Yes, the M323.J81 from Metav IndustryLine is suitable for fixture setting and assembly verification where a compact, precise reference pin is required. How should the gauge pin be stored to maintain accuracy? Store the pin clean and dry, avoid impacts and contamination; regular inspection and gentle cleaning help preserve the specified tolerance and surface condition. Is the material specified for wear resistance in shop environments? The pin is made from special steel with a workshop-grade finish, offering a balance of wear resistance and stable contact properties for frequent use. How is the part identified in documentation and inventory? Identification is provided via the article number M323.J81 and GTIN 4061905072468 for clear traceability in records and stock systems. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
19.82mm Test Pin, Single, 50mm Length, Workshop Version - Metav IndustryLine
Benefit from reliable end‑measure verification thanks to the combination of 19.82 mm nominal diameter, ±0.002 mm tolerance and a solid 50 mm measuring length — designed for demanding workshop use. Order the gauge pin directly via Metav Werkzeuge or ask our consultants if needed. Gauge pin, single — 19.82 mm Ø, 50 mm length (Metav IndustryLine) The gauge pin (19.82 mm, 50 mm) is a workshop‑grade cylindrical test pin for precise end‑measure checks and fit verification. Precision tolerance ±0.002 mm Diameter 19.82 mm, ground 50 mm length, workshop version Delivered in protective transport case Precision engineered for repeatable end‑measure checks The gauge pin is manufactured from special steel and finished to tight dimensional limits to ensure consistent results during repetitive inspection tasks. With a declared tolerance of ±0.002 mm, the pin is suitable where high repeatability is required; the small dimensional deviation reduces uncertainty when verifying bores, holes or mating features. The compact mass and cylindrical geometry limit bending under light handling, which helps maintain measurement integrity in a production environment. Designed for workshop robustness and ease of use Built as a workshop version, this test pin balances stiffness and handling comfort for routine quality checks on the shop floor. A 50 mm measuring length provides sufficient reach for typical end‑measure applications without compromising rigidity, while the precise 19.82 mm nominal diameter is suitable for gauging fits and clearance checks. Supplied in a protective transport case, the unit is protected during storage and transit, preserving the ground finish and dimensional accuracy. Integrating into quality control processes As a standard reference element for spot checks and incoming inspection, the gauge pin supports clear go/no‑go assessments and dimensional comparisons when used alongside calipers or comparators. The modest weight and compact form factor make the pin straightforward to handle during repeated use, speeding up inspection cycles and contributing to a smoother workflow. Traceability is supported via the visible SKU marking and GTIN for inventory control and process documentation. Contact Metav Werkzeuge in Emmerich for tailored advice and to request the Metav IndustryLine gauge pin M323.J82 with 19.82 mm diameter and workshop specification Technical data SKU: M323.J82 GTIN: 4061905072475 Material: Special steel Nominal diameter: 19.82 mm Measuring length: 50 mm Tolerance: ±0.002 mm Weight: 0.2 kg Version: Workshop Facts Article number: M323.J82 Length: 50 mm Diameter: 19.82 mm Mass: 0.2 kg Tolerance specification: ±0.002 mm Special features Workshop execution Supplied in protective transport case Ground diameter finish FAQ What tolerance can be expected from this gauge pin? The gauge pin M323.J82 is specified with a tolerance of ±0.002 mm, ensuring tight dimensional control for end‑measure checks. Is the pin suitable for routine shop‑floor inspections? Yes, the Metav IndustryLine workshop version is designed for routine use and is supplied in a protective transport case to preserve accuracy. What are the nominal dimensions of the test pin? The gauge pin has a nominal diameter of 19.82 mm and a measuring length of 50 mm. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
19.83mm Gauge Pin Length 50mm Workshop Version, Special Steel - Metav IndustryLine
Choose a workshop-grade single gauge pin with Ø 19.83 mm, ±0.002 mm tolerance and a 50 mm shaft for repeatable end‑dimension checks; its special steel construction and compact mass ensure consistent results in routine inspection tasks. Order the gauge pin directly via Metav Werkzeuge or ask our consultants if needed. Gauge pin M323.J83 — single workshop test pin, Ø 19.83 mm, 50 mm length (Metav IndustryLine) The Gauge pin M323.J83 is a workshop‑execution single test pin for precise end‑dimension verification and go/no‑go checks in component inspection across metalworking and assembly environments. Workshop‑grade construction Diameter Ø 19.83 mm precision Tolerance ±0.002 mm Supplied in protective transport case Reliable precision for end‑dimension verification The compact design provides repeatable performance for short‑run inspection and routine quality checks. With a nominal diameter of 19.83 mm and a verified tolerance of ±0.002 mm, the pin supports accurate go/no‑go assessment and final dimension confirmation. The combination of a short shaft and sturdy profile reduces lateral flexing during use, improving measurement reproducibility; this benefit is particularly relevant when confirming mating fits or seat diameters where small deviations matter. Practical handling and workshop suitability Constructed in special steel and specified as a workshop version, the pin balances robustness with manageable mass (approx. 0.2 kg), making it straightforward to manoeuvre by hand or seat in fixtures. The 50 mm shaft length facilitates access into blind bores and ensures sufficient engagement for stable checks. Delivery in a protective transport case keeps the gauge safe between uses and simplifies storage on a busy shop floor, reducing the risk of nicks or contamination that would otherwise affect measurement integrity. Integration into quality workflows and material compatibility The single test pin is intended for end‑dimension control and fits into established inspection routines, from incoming goods checks to final assembly verification. Its material and finish provide general compatibility with common engineering metals; the pin is suitable where a hardened, wear‑resistant probe is required to verify mating surfaces and location features. For bespoke inspection setups or batch testing, the pin can be incorporated into simple fixture jigs or paired with manual comparators to streamline acceptance decisions and minimise rework. Contact Metav Werkzeuge for ordering guidance or to discuss technical suitability of the Metav IndustryLine gauge pin M323.J83 for specific inspection tasks Technical Data Article number: M323.J83 GTIN: 4061905072482 Brand: Metav IndustryLine Facts Diameter: 19.83 mm Length: 50 mm Tolerance / Accuracy: ±0.002 mm Weight: 0.2 kg Special features Material: Special steel Workshop execution Supplied in transport case FAQ What applications suit this gauge pin? The gauge pin M323.J83 is suitable for end‑dimension verification, go/no‑go checks and seating confirmation in metalworking, assembly and inspection operations. Is the diameter specified to ±0.002 mm? Yes, the nominal diameter of 19.83 mm is supplied with an accuracy specification of ±0.002 mm for reliable pass/fail assessment. How is the pin delivered for safe handling? The pin is supplied in a protective transport case to prevent damage and facilitate safe storage between uses. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
19.84mm Gauge Pin 50mm Length Workshop Version, Special Steel - Metav IndustryLine
Precision to ±0.002 mm, robust special steel construction and a compact 50 mm length combine to deliver reliable end‑measure checks in workshop environments; order directly via Metav Werkzeuge or consult the specialists for application advice. Gauge pin M323.J84 — single gauge pin Ø19.84 mm, 50 mm length (Metav IndustryLine) The Gauge pin, single, 19.84 mm diameter, 50 mm length is a compact workshop gauge designed for accurate end‑measure inspections and fixture verification in machine shops and toolrooms. Workshop-grade special steel construction Diameter 19.84 mm with ±0.002 mm accuracy Compact 50 mm length for tight fixtures Supplied single for customised inspection setups Precision that fits tight tolerances This single gauge pin is manufactured for high‑precision end measurements, offering a measured diameter of 19.84 mm with a verified accuracy of ±0.002 mm. Such narrow tolerances reduce uncertainty during go/no‑go checks and final dimensional verification, making the component suitable where small deviations can cause assembly failures or rework. The tight tolerance supports consistent sampling in serial inspections, improving process control and lowering scrap rates. Robust workshop design for everyday handling Constructed from special steel and specified as a workshop variant, the component withstands routine handling and contact with clamping fixtures. The 50 mm length and compact geometry enable use in confined setups and jigs, while a moderate mass assists stable seating during checks. The material choice balances wear resistance with machinability so that repeated insertions and withdrawals retain dimensional stability, extending service life and preserving measurement reliability. Practical fit in quality workflows Supplied individually, the pin integrates easily into bespoke inspection stacks, gauge blocks or fixture assemblies and complements standard inspection routines in production environments. Its compact form factor simplifies storage and quick exchange in toolrooms, while the clearly defined diameter and accuracy facilitate traceable documentation in quality protocols. The M323.J84 SKU is particularly useful when specific end‑measure values are required for repeatable assembly verification or for use as a reference member in calibration procedures. Contact Metav Werkzeuge for tailored technical advice on integrating this Metav IndustryLine gauge pin into inspection routines and to arrange sample checks or procurement through the Emmerich distribution centre Technical data Article number: M323.J84 GTIN: 4061905072499 Brand: Metav IndustryLine Dimensions & mass Diameter: 19.84 mm Length: 50 mm Weight: 0.2 kg Stated accuracy: ±0.002 mm Features & materials Material: special steel Version: workshop execution Supplied: single gauge pin FAQ What accuracy can be expected from this gauge pin? The gauge pin offers an accuracy of ±0.002 mm; the M323.J84 gauge pin is specified for fine end‑measure checks where tight tolerances are required. What material is used for the pin? This item is made from special steel, designed for workshop durability and stable dimensional performance. Which applications suit this gauge pin best? Typical uses include end‑measure inspections, go/no‑go checks, fixture verification and reference measurements in machine shops and toolrooms. Is the pin supplied individually or as part of a set? The product is supplied as a single gauge pin (individual piece) for flexible integration into customised inspection arrangements. What identifiers are available for procurement and traceability? Use SKU M323.J84 and GTIN 4061905072499 for ordering and documentation of the gauge pin. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
19.85mm Gauge Pin 50mm Length Workshop Version - Metav IndustryLine
Benefit from workshop-grade construction, Special steel composition and a tight ±0.002 mm tolerance for dependable end-measure verification; order the gauge pin directly via Metav Werkzeuge or consult our specialists for tailored application advice. Gauge pin M323.J85 — single 19.85 mm diameter, 50 mm length (Metav IndustryLine) A single gauge pin, the M323.J85, for precision end‑measure checks and fixture set‑up in workshop environments. Precision ground Ø 19.85 mm, tolerance ±0.002 50 mm working length for fixture and end‑measure checks Delivered in protective transport case Workshop version for daily use and durability Accuracy that secures process reliability The M323.J85 gauge pin is manufactured to a nominal diameter of 19.85 mm with a verified ±0.002 mm dimensional tolerance, offering a reliable reference for critical fits and end‑measure controls. Such a tolerance reduces ambiguity during inspection and ensures consistent pass/fail decisions on production lines. The ground surface minimises contact variation, so comparative measurements and bench checks remain repeatable even under frequent use. Built for routine use in demanding environments Constructed from Special steel and supplied as a workshop version, the pin combines wear resistance with practical handling characteristics. The 50 mm overall length provides sufficient engagement for most fixture and gauge blocks while remaining compact for quick tool changes. Supplied in a protective transport case, the pin is shielded from knocks and contamination during storage and transit, maintaining its calibrated geometry and extending service life. Practical benefits for inspection and set‑up workflows Using a dedicated gauge pin shortens set‑up times and simplifies go/no‑go verification tasks by offering a single, traceable reference dimension for jigs and collets. The robust finish supports frequent contact with components, and the pin’s stability aids in achieving consistent alignment in assembly and machining operations. For shops seeking predictable measurement outcomes, this single test pin reduces rework and streamlines quality control routines. Contact Metav Werkzeuge for application matching, batch supply options and technical advice on integrating the M323.J85 into inspection routines Technical data Article number: M323.J85 GTIN: 4061905072505 Manufacturer: Metav IndustryLine Material: Special steel Category: Messstifte Facts Diameter: 19.85 mm Length: 50 mm Tolerance / accuracy: ±0.002 mm Weight: 0.2 kg Special features Single gauge pin for end‑measure and fixture checks Workshop execution for enhanced durability Supplied in a protective transport case Precision ground surface FAQ What tolerance can be expected from this gauge pin? The M323.J85 is made to a tolerance of ±0.002 mm, ensuring it serves as a precise reference for end‑measure verification and fit tests. Is the pin suitable for everyday workshop use? Yes, the workshop version and the choice of Special steel give the pin robustness for frequent handling and routine inspection tasks. How is the M323.J85 delivered? The gauge pin is supplied individually in a protective transport case to preserve the ground surface and dimensional integrity during storage and transport. Can this pin be used to set up fixtures and jigs? Yes, the 50 mm length and precision diameter make the pin suitable for fixture alignment and quick go/no‑go checks in production set‑ups. Does the product come with traceability or a certificate? Product documentation provided with the M323.J85 includes the standard delivery details; consult Metav Werkzeuge for options regarding calibration certificates or bespoke traceability needs. Metav IndustryLine: Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
19.86mm Gauge Pin 50mm Length Workshop Version - Metav IndustryLine
This gauge pin combines workshop‑grade durability with sub-millimetre repeatability thanks to its 19.86 mm diameter and ±0.002 mm tolerance; its compact 50 mm length supports stable seating and fast end-dimension checks. Order the gauge pin directly via Metav Werkzeuge or contact our consultants for integration advice. Gauge pin M323.J86 — 19.86 mm diameter, 50 mm length (Metav IndustryLine) The gauge pin M323.J86 is a precision control pin for end‑dimension verification and fixture alignment in workshop inspection tasks Workshop-grade finish for daily use Diameter 19.86 mm for end-measure reference Hardened special steel construction 50 mm length for stable seating Repeatable accuracy for end‑dimension checks The control pin is manufactured to a tight ±0.002 mm form tolerance, providing reliable reference points during routine inspections and small‑batch production. With its 19.86 mm nominal diameter and finely finished cylindrical surface, the component reduces measurement scatter when used as a stop or go/no‑go reference in gauges and fixtures. Classified in the micro measurement range (max. 10–100 mm), this size is optimised for fine mechanical parts where compact geometry and low bending moment ensure consistent readings. Robust workshop design that endures everyday handling Built in special steel with a workshop‑grade finish, the pin is intended for repeated seating and withdrawal in jigs and assembly fixtures. The 50 mm length gives sufficient engagement to prevent wobble while remaining easy to position by hand or with simple holders. The hardened construction lowers wear and maintains diameter stability over many cycles, so maintenance intervals are extended and the need for frequent replacement is reduced. Practical benefits for inspection and tooling workflows Using a calibrated control pin with narrow tolerance streamlines process checks and reduces scrap by making go/no‑go decisions faster and more reliable. The compact form factor permits integration into small fixtures and portable checking rigs, supporting quick in‑process verification without complex setup. Where traceable batch control is required, the clear SKU and GTIN simplify inventory and traceability in production documentation. For workshop-grade end-dimension control choose the Metav IndustryLine gauge pin M323.J86 and contact Metav Werkzeuge in Emmerich at info@metav-werkzeuge.com or +49 2822 7131930 for tailored advice Technical data Article number: M323.J86 GTIN: 4061905072512 Label: Gauge pin, single, 19.86 mm length 50 mm Manufacturer: Metav IndustryLine Key figures Diameter: 19.86 mm Length: 50 mm Accuracy: ±0.002 mm Weight: 0.2 kg ECLASS: 21170231 Materials & special features Material: Special steel Workshop design SKU: M323.J86 Story trigger: end measures FAQ What applications suit this gauge pin best? The gauge pin M323.J86 is ideal for end‑dimension checks, fixture alignment and go/no‑go references in small to medium workshop tasks where compact, repeatable references are needed. How precise is the diameter control of the pin? Diameter control is specified at ±0.002 mm, which supports tight tolerance checks and minimises measurement uncertainty in common inspection setups. Can the pin be used in assembly jigs and fixtures? Yes. The 50 mm length and hardened special steel construction make it suitable for incorporation into jigs, stops and portable checking rigs where a stable seating length is advantageous. Metav IndustryLine: Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
19.87mm Test Pin Length 50mm Workshop Version, Special Steel - Metav IndustryLine
Combining ±0.002 mm repeatability with a precisely machined 19.87 mm diameter and a compact 50 mm length, this test pin delivers dependable end‑measure verification in workshop environments; order directly via Metav Werkzeuge or consult our specialists for application matching. Test Pin M323.J87 – Gauge Pin, 19.87 mm Ø, 50 mm Length (Metav IndustryLine) A Test Pin, single, 19.87 mm diameter and 50 mm length designed for accurate end‑measure checks and precision gauging in workshop metrology. High precision ±0.002 mm tolerance Diameter 19.87 mm for end‑measure fits 50 mm overall length, workshop variant Made from special steel for wear resistance Precision where repeatability matters This gauge pin is engineered to provide ±0.002 mm dimensional stability, which reduces measurement scatter and supports reproducible inspection results. As a hardened, single‑piece test pin, it is suitable for end‑measure verification and go/no‑go jigs where a defined diameter is required. The narrow tolerance band minimises uncertainty during batch checks, shortening cycle times in quality control and decreasing the risk of rework. For operations that prioritise measurable improvement in first‑pass yield, the clear numeric accuracy of the component supports data‑driven decisions and easier traceability in inspection protocols. Robust construction for routine workshop use Manufactured from special steel, the pin combines hardness with surface integrity to withstand frequent seating and handling in production environments. The compact 50 mm length offers a balance of accessible reach and rigidity, reducing deflection when used in fixtures or during manual gauging. The instrument’s mass and finish facilitate secure seating in bores and jigs, contributing to consistent contact and less operator‑induced variation. This workshop‑grade execution is intended for everyday metrology tasks where durability and dependable geometry are priorities, allowing teams to rely on a stable reference part in repetitive measurements. Practical integration into inspection workflows With a nominal 19.87 mm diameter, the pin is compatible with matched gauge systems and purpose‑built fixtures, easing integration into existing test benches and assembly control points. The simple geometry simplifies visual inspection and cleaning, while the dimensional specification supports straightforward documentation in inspection plans. Because the design is single‑element, it is easy to identify, store and rotate within a set of master pins, streamlining inventory practices in the measurement lab. For bespoke applications, consultants at Metav Werkzeuge can advise on pairing with complementary master gauges or fixture adaptations to ensure optimal measurement chain performance. Contact Metav Werkzeuge for a bespoke recommendation based on the M323.J87 gauge pin and its workshop specifications, and let our specialists assist with selection for your specific measurement chain Technical data SKU: M323.J87 GTIN: 4061905072529 Label: Test pin, single, 19.87 mm diameter, 50 mm length Brand: Metav IndustryLine Facts Diameter: 19.87 mm Length: 50 mm Tolerance: ±0.002 mm Weight: 0.2 kg Special features Material: special steel Workshop execution Single test pin configuration Designed for end‑measure verification FAQ What tolerance can be expected from this gauge pin? The M323.J87 test pin is specified with a tolerance of ±0.002 mm, making it suitable for precise end‑measure checks where tight repeatability is required. Is the test pin suitable for fixture and jig use in production? Yes, the compact 50 mm length and robust special steel construction make this gauge pin appropriate for fixtures and jigs used in workshop environments. Can this pin be used with standard master gauge sets? Compatibility with master gauge sets is supported by the nominal 19.87 mm diameter; for bespoke matching with existing sets, Metav Werkzeuge can advise on integration. How should the pin be stored to maintain accuracy? Store the pin in a dry, vibration‑free location, ideally in protective packaging and separated from harder materials to prevent surface damage that could affect dimensional accuracy. Which applications benefit most from this test pin? Typical uses include end‑measure verification, bore gauging and assembly checks where a defined reference diameter and high repeatability are essential. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
19.88mm Gauge Pin Length 50mm Workshop Version, Special Steel - Metav IndustryLine
Take advantage of a precise reference tool that combines 19.88 mm nominal diameter, ±0.002 mm tolerance and a robust 50 mm length for repeatable seating and quick Go/No‑Go checks; order through Metav Werkzeuge or consult our specialists for integration into inspection routines. M323.J88 Gauge Pin (19.88 mm, 50 mm length) – Metav IndustryLine The M323.J88 gauge pin is a workshop‑grade reference pin designed for precision end‑measurements, fixture checking and repeatable alignment tasks in metrology and production environments. Workshop-grade construction for daily use Diameter 19.88 mm with ±0.002 mm accuracy 50 mm length for firm insertion and handling Made from special steel for wear resistance Supplied in a protective transport case Repeatable accuracy to speed up inspection A reference pin with a nominal diameter of 19.88 mm and an accuracy of ±0.002 mm provides a reliable benchmark for quick acceptance tests and dimensional checks. The tight tolerance reduces ambiguous measurements and helps to lower scrap rates by offering a distinct pass/fail criterion. Used as a fixed reference within gauges or fixtures, this precision pin supports consistent decision making on the shop floor and in quality control stations. Built for workshops and frequent handling The workshop specification emphasises durability: manufactured from special steel, the pin resists wear during repeated insertions and handling. The 50 mm length balances insertion depth and handling comfort, giving a secure seating that minimises wobble during checks. Supplied in a protective case, the item remains transport‑ready and protected from contamination when moved between benches or taken to in‑process inspection points. Integrates with existing inspection routines As a standard reference element, this pin is suited to fixture set‑up, repeatability tests and Go/No‑Go arrangements. Traceability is straightforward thanks to the visible SKU and GTIN marking, which supports inventory control and calibration records. The compact format and workshop design make it simple to position in jigs and holders, reducing set‑up time and enabling faster throughput in batch or single‑piece inspection workflows. Quality assurance and practical benefits The combination of precise diameter, proven material and robust length contributes directly to reproducible measurements and fewer reworks. For production teams and metrology technicians, the pin offers a practical way to verify bore sizes, alignment and seating without complex equipment. As a tangible part of a quality strategy, it supports documented inspection steps and strengthens confidence in dimensional conformity. Contact Metav Werkzeuge for advice on integrating the M323.J88 gauge pin into inspection procedures or to request delivery and handling options – phone +49 2822 7131930 or email info@metav-werkzeuge.com Technical Data Article number: M323.J88 GTIN: 4061905072536 Manufacturer: Metav IndustryLine Numbers / Core Technical Data Diameter: 19.88 mm Length: 50 mm Tolerance / Accuracy: ±0.002 mm Weight: 0.2 kg Special features Material: special steel Workshop execution Supplied in protective transport case Category: gauge pin SKU: M323.J88 FAQ What is the declared diameter tolerance of this gauge pin? The M323.J88 gauge pin from Metav IndustryLine is specified with an accuracy of ±0.002 mm, enabling precise Go/No‑Go and reference checks. Is the pin suitable for repeated use in a production environment? Yes, the workshop‑grade construction and special steel composition make the M323.J88 resilient for frequent insertions and routine handling. Can this gauge pin be used directly in fixture set‑up? The 50 mm length and firm seating characteristics of the pin allow direct use in fixtures and jigs for alignment and repeatability tests. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
19.89mm Gauge Pin 50mm Length Workshop Finish - Metav IndustryLine
Take advantage of precise 19.89 mm sizing with a tight ±0.002 mm tolerance and robust special steel construction for repeatable inspection results; the single unit is supplied ready for secure transport in a protective case. Order the part directly via Metav Werkzeuge or consult the specialists for application advice. Gauge pin M323.J89 — precision test pin, 19.89 mm diameter, 50 mm length (Metav IndustryLine) The gauge pin M323.J89 is a single, precision test pin designed for end‑measurement and dimensional checks in inspection, jigs and fixture applications. Diameter 19.89 mm with ±0.002 mm tolerance 50 mm overall length, workshop version Made from special steel, hardened for durability Supplied in a protective transport case High‑accuracy measurement for consistent quality control The compact design delivers a clearly defined diameter of 19.89 mm combined with a manufacturing tolerance of ±0.002 mm, ensuring reliable fit‑checks and repeatable go/no‑go assessments. This degree of precision reduces measurement variation on the shop floor and supports tighter process control, which in turn lowers the risk of rework and scrap. Robust construction tailored to workshop environments Manufactured from special steel and finished for workshop use, the pin offers mechanical resilience during frequent insertion and withdrawal cycles. The 50 mm overall length provides stable engagement in fixtures while remaining manageable for bench inspection. The solid build translates into long service life and consistent contact surfaces that preserve measurement fidelity. Practical supply and traceability for inspection workflows Delivered as a single unit and protected in a transport case, the pin is intended for safe storage and movement between measuring stations. Identification via SKU M323.J89 and GTIN 4061905072543 simplifies inventory and traceability within inspection routines. The compact weight and workshop classification make the component easy to integrate into existing gauges, jigs or dedicated test rigs. Contact Metav Werkzeuge today to discuss how the M323.J89 can be integrated into your inspection process or to arrange purchase and delivery from Emmerich. Technical Data Article number: M323.J89 GTIN: 4061905072543 Label: Gauge pin, single, 19.89 mm diameter, 50 mm length Category: Messstifte Core dimensions & tolerances Diameter: 19.89 mm Length: 50 mm Tolerance: ±0.002 mm Weight: 0.2 kg eClass: 21170231 Features & Materials Material: special steel Workshop version Supplied in protective transport case Single unit delivery FAQ What tolerance does the M323.J89 offer? The M323.J89 gauge pin is manufactured to a tolerance of ±0.002 mm, making it suitable for precise fit and dimensional checks in inspection tasks. Can this test pin be used in jig and fixture applications? Yes, the Metav IndustryLine M323.J89 is intended for jigs, fixtures and end‑measurement routines where a defined reference diameter and durable contact surface are required. Is the pin supplied ready for transport and storage? The M323.J89 is supplied as a single unit in a protective transport case to safeguard the measuring surface during handling and transit. How can the part be identified in stock and documentation? Identification is facilitated by SKU M323.J89 and GTIN 4061905072543, which support inventory control and traceability in quality systems. Metav IndustryLine: Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
19.8mm Test Pin 50mm Length Workshop Version - Metav IndustryLine
Take advantage of precise dimensional control and robust workshop design to streamline inspection tasks; the combination of ±0.002 mm accuracy and a compact 19.8 mm diameter ensures reliable end‑dimension checks and effortless repeatability. Order the gauge pin directly via Metav Werkzeuge or ask the consultants for application guidance. M323.J80 Gauge Pin — 19.8 mm diameter, 50 mm length (Metav IndustryLine) A gauge pin M323.J80 designed for precise end‑dimension verification and repeatable fit tests in workshop inspection and component control. High repeatability ±0.002 mm Diameter 19.8 mm for end‑dimension testing 50 mm hardened length for stable seating Workshop version construction Precision for repeatable end‑dimension checks The test pin delivers a verified accuracy of ±0.002 mm, making it suitable for tasks where repeatability defines process reliability. As a compact inspection tool it reduces setup time during batch checks and supports rapid go/no‑go assessment of bore diameters and mating parts. The tight tolerance translates directly into fewer downstream rejects and more predictable assembly performance, because measurement uncertainty is minimised and traceable checks become part of standard quality routines. Robust material and workshop construction for daily use Manufactured from special steel and supplied in a workshop version, the test pin resists normal wear and provides consistent contact geometry over repeated cycles. With a 50 mm usable length and a nominal 19.8 mm diameter the component offers stable seating in fixtures and gauges; this stiff geometry limits lateral deflection and improves handling during manual inspection. The resulting combination supports frequent use on the shop floor while maintaining the metrological characteristics required for reliable pass/fail decisions. Easy integration into inspection workflows and tooling This compact gage pin is optimised for simple incorporation into existing fixtures, plug gauges and test assemblies. Its dimensions make it a convenient reference for end‑dimension checks, assembly trials and runout comparisons; traceability is supported by clear identifiers and numeric markings. The design favours quick interchange between stations, which shortens inspection cycles and helps maintain production flow without complex setup. For audit trails and quality documentation the pin’s specification is concise and directly usable in inspection reports. Contact Metav Werkzeuge for tailored advice on fitting the Metav IndustryLine gauge pin into inspection jigs or to receive a specification match for production needs Technical Data Article number: M323.J80 GTIN: 4061905072451 Category: Gauge pins Manufacturer: Metav IndustryLine Facts Diameter: 19.8 mm Length: 50 mm Accuracy: ±0.002 mm Weight: 0.2 kg Special features Material: Special steel Version: Workshop execution Intended use: End‑dimension checks and fit testing FAQ What tolerance can be expected from this gauge pin? The M323.J80 gauge pin is specified with an accuracy of ±0.002 mm, suitable for precise end‑dimension verification in inspection tasks. Is the M323.J80 suitable for repeated workshop use? Yes, the workshop version and special steel construction of the M323.J80 are intended for regular handling and routine fit‑checking on the shop floor. How does the 19.8 mm diameter affect application selection? A 19.8 mm nominal diameter makes the pin ideal for bore checks and mating‑part tests around that nominal size; it functions as a fixed reference for go/no‑go and assembly trials. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
19.91mm Gauge Pin 50mm Length Workshop Version, Special Steel - Metav IndustryLine
The combination of a 19.91 mm measuring diameter, a ±0.002 mm tolerance and a 50 mm shank ensures reliable end‑measure verification and stable handling in workshop environments; order the gauge pin directly via Metav Werkzeuge or consult our specialists for application support and delivery from Emmerich. Gauge pin (single) 19.91 mm, 50 mm length — Metav IndustryLine The Gauge pin (single) 19.91 mm, 50 mm length is a workshop‑grade test pin designed for end‑measure verification, assembly alignment and repeatable inspection tasks in production and quality control settings. Workshop-grade construction Diameter precisely 19.91 mm Tolerance ±0.002 mm Special steel for wear resistance Accuracy that protects production tolerances A reliably defined tolerance is the fastest route to fewer reworks and stable assembly processes. This gauge pin is specified with ±0.002 mm positional accuracy, which places it in the high‑precision bracket for workshop gauging tasks. The tight tolerance means that end‑measure checks and seating tests produce consistent, comparable results, reducing downstream adjustments. Where measurement uncertainty directly affects part acceptance, the controlled manufacture of the pin supports reproducible gauging and quick decisions on go/no‑go criteria. Robust workshop design for repetitive use Designed as a workshop version, the pin combines a 50 mm length with a finished 19.91 mm diameter to give good handling without sacrificing rigidity. Machined from special steel, the component is dimensionally stable under repetitive contact and resists the wear typical of frequent checking cycles. The mass and geometry support a secure fit in fixtures and jigs while remaining simple to manipulate by hand or with basic holding devices. The overall design reduces measurement variation caused by unstable contact or deformation during routine use. Traceability and practical integration into inspection routines The test pin is supplied as a single piece with the clear designation M323.J91, allowing straightforward inventory control and traceability in inspection protocols. The concise specification and standard geometry make the pin suitable for quick comparative checks, bench verification and incorporation into basic gauge sets. Where documented evidence of routine checks is required, the consistent characteristics of this component speed up documentation and help maintain production quality. Choosing a recognised supplier further supports dependable replenishment and consistent part quality. For tailored application advice or to secure supply of the Metav IndustryLine gauge pin M323.J91, contact Metav Werkzeuge for expert guidance and logistical support from Emmerich Technical Data Article number: M323.J91 GTIN: 4061905072567 Brand: Metav IndustryLine Facts Diameter: 19.91 mm Length: 50 mm Tolerance: ±0.002 mm Weight: 0.2 kg Special features Workshop version Material: special steel Supplied as single piece Label: Prüf‑/test pin, single, 19.91 mm FAQ What tolerance does the gauge pin offer? The Metav IndustryLine gauge pin M323.J91 is manufactured to a tolerance of ±0.002 mm, making it suitable for high‑precision workshop gauging and end‑measure verification. For which tasks is this test pin intended? This test pin is intended for end‑measure checks, assembly alignment and repeatable inspection tasks where a 19.91 mm reference diameter is required. What material is the pin made from and why is that important? The pin is made from special steel, chosen for dimensional stability and resistance to wear during frequent contact‑type inspections. How is the item supplied and how is it identified in stock? The component is supplied as a single piece and identified as M323.J91, which simplifies stockkeeping and traceability in inspection procedures. Metav IndustryLine: Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
19.92mm Gauge Pin 50mm Length Workshop Version, Special Steel - Metav IndustryLine
The M323.J92 gauge pin combines precise dimensional control with workshop-ready durability; its Ø 19.92 mm diameter and 50 mm length suit end-dimension checks and gauge setting, while a tight tolerance of ±0.002 mm ensures repeatable results. Supplied in a protective case for transport, order the item directly via Metav Werkzeuge or consult the team for application advice. Gauge pin M323.J92 — single test pin, Ø 19.92 mm, 50 mm length The gauge pin M323.J92 is a workshop-grade single test pin designed for end-dimension verification and setting of internal gauges in production and inspection environments. Workshop-grade execution, robust design Diameter calibrated to 19.92 mm ±0.002 Special steel construction for wear resistance Supplied in protective case for transport Precision where it reduces rework This compact test pin delivers high repeatability through a nominal diameter of 19.92 mm and a stated tolerance of ±0.002 mm, making it suitable for pass/fail checks, go/no-go fixtures and reference measurements. The narrow tolerance reduces ambiguity during inspection and helps to lower scrap rates by providing a clear physical reference. For operators and metrology technicians, the measurable benefit is a faster decision process at the inspection stage and fewer corrective operations downstream. Robust design for everyday workshop use Manufactured from special steel, the pin is engineered to withstand frequent handling and the mechanical stresses common in workshop environments. The 50 mm length offers a stable engagement area for insertion checks while remaining easy to handle; at around 0.2 kg weight the component balances solidity with manoeuvrability. The workshop execution emphasises durability and serviceability, supporting repeated use in toolrooms, machine shops and quality-control benches without rapid wear. Practical handling, storage and transport benefits Delivery in a protective case safeguards the nominal diameter and surface condition during transport and storage, preserving measurement integrity until first use. The compact format fits standard instrument drawers and portable inspection kits, allowing quick access during set-up and maintenance tasks. Clear labelling and the included GTIN support inventory workflows and traceability within production lines and calibration records. Fits into established inspection workflows As a single-diameter gauge pin, this test pin integrates into existing measuring routines: it serves as a reference for internal diameter checks, fixture calibration and end-dimension verification. The straightforward design reduces operator training time and simplifies fixture design for quality control. With its workshop-grade specification, the component contributes to consistent inspection outcomes, supporting production efficiency and dependable documentation for quality systems. Contact Metav Werkzeuge for tailored metrology advice and to secure the M323.J92 for workshop applications — phone +49 2822 7131930 or email info@metav-werkzeuge.com Technical data Article number: M323.J92 GTIN: 4061905449710 Material: special steel Weight: 0.2 kg Length: 50 mm Numbers Diameter: 19.92 mm Tolerance: ±0.002 mm Length: 50 mm Weight: 0.2 kg Special features Workshop-grade execution Supplied in protective case for transport Category: gauge pins Image asset available FAQ What applications is this gauge pin suitable for? The M323.J92 gauge pin is intended for end-dimension checks, fixture calibration and internal gauge setting in production and inspection environments. Is the pin suitable for frequent workshop use? Yes, the workshop-grade construction and special steel make the M323.J92 robust enough for repeated handling in machine shops and toolrooms. What tolerance can be expected from the pin? The test pin is specified with a tolerance of ±0.002 mm, providing a tight reference for go/no-go checks and precision fixture setup. Does the delivery include protective packaging? The M323.J92 is supplied in a protective case to preserve the diameter and surface condition during transport and storage. Metav IndustryLine: Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
19.93mm Gauge Pin 50mm Length Workshop Version - Metav IndustryLine
Combine high-precision repeatability with a robust workshop build: the compact 19.93 mm diameter and 50 mm length make this gauge pin ideal for reliable end‑measurements and quick reference checks. Order directly via Metav Werkzeuge or consult our specialists for application-specific guidance. Gauge Pin M323.J93 – 19.93 mm Ø, 50 mm Length (Metav IndustryLine) The Gauge Pin M323.J93 is a precision end‑measurement pin for workshop and inspection tasks, designed for repeatable diameter checks and reference gauging in small to medium components. 19.93 mm diameter precision High accuracy ±0.002 mm Workshop‑grade construction 50 mm total length Consistent precision that reduces rework The pin delivers ±0.002 mm dimensional stability, which translates into dependable pass/fail decisions during incoming inspection and in‑process checks. Such repeatability reduces corrective work and scrap by catching deviations early. The combination of a narrowly controlled diameter and a defined contact length ensures that measurements remain comparable from one operator to the next, supporting a more efficient quality workflow. Durable design for everyday workshop use Manufactured from special steel, the component is finished for resilience under regular handling and contact. The workshop‑grade execution offers a balance between toughness and dimensional stability, so the pin resists wear while retaining its calibrated form. The 50 mm overall length gives a solid handling grip and positive seating in gauges or jigs, simplifying fast checks without compromising accuracy. Suited to micro-range end measurements With a nominal diameter of 19.93 mm, the pin sits in the micro range classification (small, precision dimensions up to 100 mm), making it particularly appropriate for fine mechanical parts, precision bores and end‑measurements where compactness and stiffness are required. For applications that demand tight fit tolerances, the narrow diameter tolerance helps ensure components assemble correctly first time. Practical traceability and workshop integration Supplied as a single item with a clear item designation and manufacturer reference, the pin integrates easily into inspection routines and tool sets. The compact form factor allows rapid swapping between gauges and jigs, while the defined tolerance supports a consistent inspection standard across production batches. For purchasers seeking reliable small‑part gauges, this execution supports steady quality control without complex set‑up. Contact Metav Werkzeuge today for tailored advice on integrating the Metav IndustryLine gauge pin M323.J93 into production checks and to secure immediate delivery from our European stock. Technical data Article number: M323.J93 GTIN: 4061905449727 Manufacturer: Metav IndustryLine Facts Diameter: 19.93 mm Length: 50 mm Weight: 0.2 kg Tolerance: ±0.002 mm Special features Material: special steel Workshop‑grade execution Single item supply E‑class: 21170231 FAQ What level of accuracy does this gauge pin provide? The gauge pin is specified with a dimensional tolerance of ±0.002 mm, which supports high‑precision checks and repeatable pass/fail evaluations for small tolerances. Which applications suit this 19.93 mm pin? This diameter and form are intended for end‑measurements, reference gauging and quick diameter checks on small to medium components, especially where compact, stiff measuring tools are required. Is the pin suitable for frequent workshop use? Yes. The special steel construction and workshop‑grade execution provide wear resistance and robustness for everyday inspection tasks. How is the item identified for inventory and traceability? The item is supplied as a single gauge pin with the manufacturer reference M323.J93 and GTIN 4061905449727 for straightforward inventory control. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
19.94mm Gauge Pin 50mm Length Workshop Version, Special Steel in Case - Metav IndustryLine
A workshop-grade gauge pin that pairs a 19.94 mm diameter with a tight ±0.002 mm tolerance and special steel construction for dependable end‑measurements; the 50 mm length and robust finish support repeated use in production and inspection. Order directly via Metav Werkzeuge or consult their specialists for application advice. Gauge pin, single, 19.94 mm diameter, 50 mm length (Metav IndustryLine) The gauge pin 19.94 mm is a workshop-grade end‑measurement standard for bore checks, fit verification and go/no‑go comparisons in daily inspection and production environments. Workshop-grade special steel construction Diameter precisely 19.94 mm, tolerance ±0.002 Length 50 mm for standard end‑measurements Supplied in transport case for secure handling Consistent accuracy that reduces rework High repeatability is central to efficient quality control; the ±0.002 mm tolerance of this gauge pin narrows measurement uncertainty and minimises the need for rework or secondary checks. Manufactured from special steel, the pin retains dimensional stability under frequent handling and resists wear in typical workshop conditions. The combination of a set diameter and controlled manufacturing tolerance supports predictable mating with gauges, plugs and bores, so inspection intervals and corrective actions can be planned with greater confidence. Robust design for busy workshop routines Built as a workshop‑grade tool, the pin’s 50 mm length provides a practical balance between reach and rigidity for end‑measurement tasks. The robust finish and compact mass suit handheld use as well as fixture mounting, while the supplied transport case protects the pin during storage and movement between workstations. This practical packaging simplifies logistics in small and medium workshops and reduces handling damage that would otherwise compromise measurement reliability. Fits into inspection workflows with minimal fuss As an end‑measurement aid, the pin is ideal for checking bore sizes, verifying fits and confirming end dimensions at the workbench or on the machine. The simple geometry makes results easy to interpret and integrate into standard inspection records; the pin’s stable material properties support repeat measurements throughout a shift. For operations that require a clear traceable item description, the component is identified by its article data and GTIN in the technical specification below, enabling straightforward inventory and quality‑control documentation. Choose the Metav IndustryLine gauge pin for reliable end‑measurement performance and pragmatic workshop handling — order via Metav Werkzeuge GmbH in Emmerich or request application guidance from their specialists at info@metav-werkzeuge.com or +49 2822 7131930 Technical data SKU: M323.J94 GTIN: 4061905449734 Label: Gauge pin, single, 19.94 mm diameter, 50 mm length ECLASS: 21170231 Core dimensions Diameter: 19.94 mm Length: 50 mm Tolerance: ±0.002 mm Weight: 0.2 kg Features and materials Material: special steel Workshop version Supplied in transport case Story trigger: end‑measurement FAQ What diameter does the pin have? The gauge pin has a diameter of 19.94 mm, specified for precise end‑measurement tasks. What tolerance is achieved? Tolerance is ±0.002 mm, ensuring close dimensional conformity for inspection use. What is the pin made from? The pin is manufactured from special steel, chosen for stability and wear resistance in workshop environments. What length is the pin and how is it packaged? Length is 50 mm and the pin is supplied in a transport case to protect it during handling and storage. What applications suit this pin? Typical uses include bore checks, fit verification and general end‑measurement tasks in production and inspection. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
Fast, tactile checks where electronics are impractical
Gauges and test pins provide unequivocal go/no-go results for threads, bores, gaps and radii without relying on electronics. The range covers plug gauges and ring gauges for internal and external threads, feeler gauges and precision feeler strips for micro‑gap assessment, plus probe pins and measuring pins for tactile diameter and pitch checks.
How these tools work in the production environment
Mechanical gauges operate as direct reference standards: a plug gauge or ring gauge verifies conformity to thread profiles and mating ability, while limit gauges separate accept from reject in a single step. Test pins are used to tactilely measure small bore diameters, centre‑to‑centre distances and radii. Manufactured from hardened gauge steel or ceramic and often precision lapped, these instruments deliver immediate physical results that are ideal for incoming inspection, machine‑side checks and final control.
Measurable benefits that affect production performance
- Reduced scrap and rework through rapid, unambiguous pass/fail assessment.
- Increased repeatability thanks to very low measurement uncertainty and fine lapping.
- Lower downtime: quick checks at the machine save cycle time and reduce setup periods.
- Durable construction with high wear resistance from specialised, low‑distortion alloys.
- Versatile delivery formats: individual gauges, organised sets in wooden cases or metre‑length feeler rolls compliant with DIN 2269.
Why Metav is the practical choice for precision supplies
Metav combines decades of expertise with a broad warehouse and quality filtering from Emmerich. As a precision partner for industry, craft and trade, Metav supplies a comprehensive selection of gauges and test pins alongside complementary tools such as precision calipers and setting rings. With over 48,000 customers and a catalogue exceeding 250,000 items, Metav is positioned to supply reliably, reduce vendor complexity and support traceable quality control to national standards.
Summary
Gauges and test pins are indispensable for dependable, repeatable quality assurance where tactile, mechanical verification is preferred. Choose these plug gauges, ring gauges, feeler strips and probe pins when immediate, robust measurement decisions are required on the shop floor.
FAQ
What materials are gauges and test pins typically made from?
Gauges and test pins are usually manufactured from hardened gauge steel for durability and wear resistance; ceramic variants are available where thermal stability and minimal wear are critical.
How do thread gauges ensure mating capability?
Thread plug gauges and ring gauges check flank diameters and thread form against standards, providing a clear go/no‑go verdict that confirms pairability with mating parts.
Which tolerance class should I choose for probe pins and gauge sets?
Select tolerance classes aligned with your inspection requirements; for high‑precision tasks, sets produced to DIN 2269 or equivalent tolerance classes ensure micrometre‑level control and repeatability.
Can feeler gauges measure contact gaps in valve and engine work reliably?
Yes. Feeler gauges and precision feeler strips, supplied either as a fan or metre‑length rolls, allow accurate assessment of valve clearances and contact gaps down to micrometre increments.
How do limit gauges speed up in‑process inspection?
Limit gauges separate good from bad in a single, tactile operation, enabling rapid go/no‑go checks at the machine and reducing both inspection time and the likelihood of human interpretation errors.
Fragen zu diesen Produkten??
Mit mehr als 30 Jahren Erfahrung beraten wir Sie gerne persönlich.
Tel.: +49 2822 7131930
Mail: info@metav-werkzeuge.com