Precision gauge blocks and plug gauges for reliable dimensional control
Mechanical gauge blocks and plug gauges are essential for tactile verification of threads, bores and gap dimensions, providing fast, unambiguous go/no-go results that enhance process reliability and reduce scrap. Designed for industrial metalworking and toolmaking, these precision tools support incoming inspection and final quality checks by delivering traceable measurements in applications such as thread inspection, bore diameter testing and spacing checks. Manufactured from specially hardened, low-distortion alloys and fine-lapped for minimal measurement uncertainty, the range includes thread plug gauges, precision plug gauges and calibration gauge blocks to ensure long-term repeatability and wear resistance.
5.27mm Gauge Pin Single ±0.001mm Length 50mm Workshop Finish - Metav IndustryLine
Precise workshop gauge pin with ±0.001 mm tolerance and a compact 5.27 mm diameter ensures reproducible end‑measurements; robust special steel construction and a 50 mm working length support reliable inspection routines. Benefit from high repeatability and straightforward integration into gauge sets for smoother quality checks. Order the gauge pin directly via Metav Werkzeuge or ask our consultants if needed. Gauge Pin M323.527 (Test Pin) — Ø 5.27 mm, ±0.001 mm, Length 50 mm Gauge Pin M323.527 for fine end‑measurement tasks in workshop inspection and gauge assemblies Workshop‑grade accuracy ±0.001 mm Diameter 5.27 mm for end measurements Length 50 mm for compact inspection Precision that reduces uncertainty in inspection The ±0.001 mm specification reflects a workshop‑grade measurement tolerance intended for demanding end‑measurement tasks where small deviations lead to costly rework. Manufactured from special steel, the pin preserves its diameter under regular handling and resists premature wear, which maintains measurement repeatability across inspection cycles. This level of control supports tighter in‑process acceptance criteria and helps to identify out‑of‑tolerance parts early in production, improving throughput and reducing scrap rates. Compact format tailored to fine mechanical work Classified in the Micro segment (maximum measurement range under 10 mm), the compact geometry allows precise entry into small bores and fine assemblies without compromising stiffness. With a nominal 5.27 mm diameter and 50 mm working length, the pin is designed for use in gauge sets, plug‑gauge applications and dedicated inspection jigs where accessibility and dimensional fidelity are paramount. The short, rigid profile reduces deflection during handling, making it suitable for watchmaking, microcomponents and precision subassemblies. Built for regular workshop use and straightforward handling The workshop version construction balances surface finish and mechanical resilience to withstand routine handling in a production environment. The combination of material choice and machining tolerances ensures the contact face remains true under repeated cycles, preserving the nominal diameter and limiting measurement drift. A low mass (approx. 0.011 kg) makes the pin easy to position in fixtures while the plain design facilitates rapid visual inspection of the contact surface before use. Integration into inspection workflows and tooling As a single‑piece test pin, the item integrates cleanly into existing gauge configurations and fixture bores, providing a defined reference for end‑measurements and comparative checks. The simple geometry allows the pin to be used as a locating element or reference probe in both manual and semi‑automated setups. Technical teams can use the pin to verify bore diameters, set gauge stacks or complement master gauges when traceable dimensional checks are required in routine quality control. Arrange technical advice or request delivery of Metav IndustryLine gauge pins from Metav Werkzeuge in Emmerich: phone +49 2822 7131930, email info@metav-werkzeuge.com Technical Data Article number: M323.527 GTIN: 4061905060069 Manufacturer: Metav IndustryLine Facts Diameter: 5.27 mm Length: 50 mm Tolerance: ±0.001 mm Weight: 0.011 kg ECLASS: 21170231 Special features Material: Special steel Workshop version Single piece delivery Measurement range nominal: 5.27 mm FAQ What tolerance is guaranteed for this gauge pin? The gauge pin M323.527 is manufactured to a tolerance of ±0.001 mm, offering high repeatability for end‑measurement duties. Which materials is the pin suitable for in inspection tasks? The M323.527 gauge pin is intended as a dimensional reference and is compatible with inspection of parts made from typical workshop materials; material compatibility depends on the tested component, not the pin itself. Is the M323.527 suitable for use in small‑bore gauges and micro assemblies? Yes, with a 5.27 mm diameter and 50 mm length the gauge pin is designed for micro‑scale applications, small‑bore checks and compact fixture integration. Can this test pin be used as a locating element in fixtures? The M323.527 functions well as a locating or reference element in measuring jigs and gauge sets due to its rigid, turned geometry and precise diameter control. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
5.28mm Gauge Pin Single, ±0.001 mm, Length 50 mm, Workshop Version - Metav IndustryLine
Take advantage of the combination of micrometric accuracy (±0.001 mm), a 5.28 mm measuring diameter and a rugged workshop design for consistent end‑dimension verification; order the part directly via Metav Werkzeuge or contact our consultants for technical guidance. Gauge pin M323.528 — Ø 5.28 mm, ±0.001 mm precision (Metav IndustryLine) A single gauge pin, 5.28 mm Ø, ±0.001 mm tolerance, 50 mm length intended for precise end‑dimension checks and workshop inspection tasks Workshop version, robust design Diameter 5.28 mm, tolerance ±0.001 mm Length 50 mm, compact measuring shank Supplied in transport case for protection Consistent, micrometre‑class inspection performance This precision test pin delivers a tolerance of ±0.001 mm, which corresponds to micrometre‑level separation of acceptable and non‑conforming parts in fine inspection work. Manufactured from special steel, the pin maintains form stability and wear resistance across repeated insertions and checks. The combination of a tightly controlled diameter and a stable shank reduces measurement scatter and supports repeatable go/no‑go decisions on the shop floor or at the inspection bench. Such exactness shortens troubleshooting loops and lowers the risk of costly rework. Built for workshop handling and transport Designed as a workshop specification, the pin balances stiffness and manageability with a 50 mm overall length and a mass of only 0.011 kg, which makes it simple to position in gauges and fixtures. The compact geometry minimises deflection during manual handling while the supplied transport case protects the measurement face from contamination and mechanical damage during storage or transit. This practical robustness preserves the pin’s dimensional integrity and extends service life, so calibration intervals remain predictable. Traceability and practical use in inspection routines The gauge pin is supplied as a single item with clear identification (M323.528, GTIN 4061905060854) for inventory and traceability. Its nominal diameter of 5.28 mm and high tolerance make it suitable for end‑dimension checks, plug fittings and verification of mating features where repeatable limits are required. As part of a Metav IndustryLine offering, the component fits into systematic inspection setups and can be integrated into fixture checks or manual gauge stacks to speed up quality‑control workflows and stabilise production output. For reliable end‑dimension verification, select the Metav IndustryLine gauge pin M323.528 — contact Metav Werkzeuge for expert advice at info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: M323.528 GTIN: 4061905060854 Brand: Metav IndustryLine Facts Diameter: 5.28 mm Length: 50 mm Tolerance: ±0.001 mm Weight: 0.011 kg Special features Material: Special steel Workshop execution Supplied in transport case Single item delivery FAQ What tolerance does the gauge pin offer? The gauge pin M323.528 is specified with a tolerance of ±0.001 mm, suitable for micrometre‑level inspection tasks. Which material is used for the pin? The pin is made from special steel, selected for dimensional stability and wear resistance in workshop use. Is the part supplied ready for transport and storage? Yes — the item is supplied in a protective transport case to safeguard the measuring face and ensure repeatable storage conditions. What applications suit this gauge pin? Typical uses include end‑dimension verification, plug‑fit checks and fixture reference gauges where a precise diameter of 5.28 mm is required. How is the product identified for stock and traceability? Identification is provided via the article number M323.528 and GTIN 4061905060854 for straightforward inventory management. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
5.29mm Gauge Pin Single, ±0.001mm, 50mm Length, Workshop Version - Metav IndustryLine
Take advantage of the combination of ultra-fine accuracy (±0.001 mm), a precise 5.29 mm nominal diameter and a compact 50 mm length to secure repeatable end-measurements in workshop environments; order the pin directly via Metav Werkzeuge or consult our specialists for application advice. Gauge pin M323.529 — single 5.29 mm, ±0.001 mm, 50 mm length (Metav IndustryLine) Gauge pin M323.529 is a single-purpose precision pin for end-dimension checks and gauging tasks in metalworking and toolrooms High precision: ±0.001 mm tolerance Nominal diameter 5.29 mm for end gauges 50 mm length in hardened special steel Workshop-grade design for durable use Secure dimensional control with sub-micron tolerance The core benefit of this precision pin is repeatable measurement certainty: with a specified tolerance of ±0.001 mm, the element supports tight acceptance criteria in small-bore inspections and finishing checks. The 5.29 mm nominal diameter simplifies reference-based comparisons and fits typical metrology setups for plug-style verification. By converting this mechanical accuracy into clear pass/fail decisions, production downtime is reduced and rework rates fall — a direct efficiency gain for machining and quality departments. Durable, workshop-ready construction that reduces handling uncertainty Made from special steel and supplied in a workshop configuration, the pin balances hardness with dimensional stability across repeated use. The compact 50 mm length produces a stiff, low-deflection measuring member ideal for short-run checks and fixture validation. The low mass (approximately 0.012 kg) makes the component easy to position while remaining robust under normal workshop handling. These material and design choices protect measurement integrity and extend service life compared with softer or loosely toleranced counterparts. Practical integration and traceable identification for process reliability This precision pin integrates into existing gauging routines where end-measurements are required, for example in bore inspection, final part verification and fixture set-up. The article is listed as M323.529 and carries the GTIN for inventory tracking and procurement. For specialised requirements such as certification or batch traceability, Metav Werkzeuge can advise on available options and fitment into quality-control chains. The combination of compact form, precise tolerance and a workshop standard build supports consistent, auditable measurement results. For controlled, workshop-grade gauging choose the Metav IndustryLine M323.529 — contact Metav Werkzeuge for availability and technical guidance Technical data Article number: M323.529 GTIN: 4061905060861 Brand: Metav IndustryLine Facts Diameter: 5.29 mm Length: 50 mm Tolerance: ±0.001 mm Weight: 0.012 kg Special features Material: special steel Design: workshop execution Application hint: end-dimension measurement FAQ What is the measurement tolerance of this gauge pin? The gauge pin M323.529 is specified with a tolerance of ±0.001 mm, enabling very fine end-dimension checks in quality control. Which material is used for the pin and how does it affect durability? The pin is manufactured from special steel; this material choice supports hardness and dimensional stability suitable for workshop use and repeated gauging operations. What length and diameter does the pin have? The pin has a nominal diameter of 5.29 mm and a length of 50 mm, making it suitable for short-reach end-measurements and fixture verification. How is the item identified for ordering and stock management? The product is listed under article number M323.529 and carries GTIN 4061905060861 for procurement and inventory control. Is a calibration certificate included with the pin? No calibration certificate is specified in the product data; please contact Metav Werkzeuge for available calibration or certification services if required. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
5.2mm Precision Test Pin ±0.001mm Length 50mm Workshop Case - Metav IndustryLine
Take advantage of the combination of ultra‑fine ±0.001 mm accuracy, a compact Ø 5.20 mm form and a robust workshop design for consistently reproducible end‑dimension checks; the pin is supplied in a protective transport case for safe storage and handling. Order the Test Pin directly via Metav Werkzeuge or consult our specialists for application advice. Test Pin M323.520 — precision Ø 5.20 mm, ±0.001 mm The Test Pin M323.520 is a single precision measuring probe for end‑dimension checks and reference measurements in workshop metrology Workshop version, robust construction Diameter 5.20 mm with ±0.001 mm accuracy Hardened special steel for wear resistance Supplied in protective transport case Reliable reference for end‑dimension inspection The M323.520 serves as a high‑accuracy reference for end‑dimension checks where repeatability is essential. With a nominal diameter of 5.20 mm and a tolerance of ±0.001 mm, the pin permits micrometric verification of mating bores, gauge seats and turned ends. This level of precision corresponds to a one‑micrometre tolerance band, which reduces uncertainty in pass/fail decisions and speeds up QC routines by providing an unequivocal mechanical reference without complex interpretation. The compact geometry and defined contact area also limit measurement variability caused by seating or angular misalignment. Built for workshop use and secure handling Designed as a workshop execution, the probe combines special steel hardness with a straight 50 mm shank for sturdy, repeatable placement in fixtures or test jigs. The 50 mm length gives sufficient reach for many end‑dimension tasks while remaining easy to handle during series checks. Supplied in a protective transport case, the pin arrives ready for safe storage and transport, reducing the risk of damage and maintaining calibration integrity between uses. The light mass supports quick manual handling and rapid insertion into gauges without introducing appreciable deflection. Fits micro‑measurement workflows and assembly checks Classified in the Micro range for compact measuring tools, this test pin is ideal where space is limited and fine mechanical components demand tight tolerances. Its dimensions and accuracy make it suitable for use in incoming inspection, fixture validation and final assembly checks of small parts. The robust material choice provides long service life under repeated contact, lowering lifecycle costs by extending intervals between replacements. Integration into standard inspection tables or bespoke holders is straightforward because the geometry follows conventional probe proportions. For precise workshop measurement tasks, request a quote or application recommendation for the Metav IndustryLine Test Pin M323.520 from Metav Werkzeuge—contact our specialists for tailored advice and fast delivery from Emmerich. Technical data SKU: M323.520 GTIN: 4061905059124 Material: Special steel Label: Test pin, single, 5.20 mm, ±0.001 mm, length 50 mm Facts Diameter: 5.20 mm Measuring range: 5.2 mm Accuracy: ±0.001 mm Length: 50 mm Weight: 0.011 kg Special features Workshop execution Supplied in protective transport case Intended for end‑dimension checks Robust geometry for fixture integration FAQ What is the exact diameter and tolerance of the pin? The Test Pin M323.520 has a nominal diameter of 5.20 mm with a tolerance of ±0.001 mm. Is the pin suitable for routine workshop inspection? Yes. The workshop execution and hardened special steel make the M323.520 suitable for regular use in inspection benches and test jigs. How is the pin delivered and protected during transport? The probe is supplied in a protective transport case to prevent damage and preserve measurement integrity. Can this pin be used as a reference for bore gauges and assembly checks? The M323.520 is designed for end‑dimension reference work and integrates well with bore gauges, fixtures and assembly inspection processes. Metav IndustryLine: Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
5.31mm Gauge Pin Single ±0.001mm Length 50mm, Workshop Version - Metav IndustryLine
Reliable workshop precision: a robust 50 mm pin with ±0.001 mm tolerance and a 5.31 mm nominal diameter provides repeatable end‑measure checks; workshop‑grade construction and delivery in a protective case support safe transport and everyday use. Order the gauge pin directly via Metav Werkzeuge or ask our consultants if needed. Gauge pin M323.531 — precision test pin Ø 5.31 mm, ±0.001 mm (Metav IndustryLine) The Gauge pin M323.531 is a single precision test pin designed for end‑measure inspection and tactile verification tasks in workshop and quality‑control environments. Precision tolerance ±0.001 mm Diameter 5.31 mm, length 50 mm Workshop‑grade special steel construction Supplied in a protective transport case Consistent accuracy for critical end‑measure checks High reproducibility in dimensional inspection is the core advantage of this gauge pin. With a declared ±0.001 mm tolerance the component enables fine end‑measure verification and fit checks that reduce scrap and rework in production. The tight tolerance supports applications where small clearances matter; by using a hardened measuring pin, bench checks or ring‑gage comparisons become a reliable part of the quality routine. This level of control is particularly relevant in precision engineering, toolmaking and small‑batch production where measurable certainty is required. Built for workshop use: material and handling benefits A workshop‑oriented design combines practical handling with long service life. The pin is made from special steel, giving it improved wear resistance and dimensional stability under repeated use, while its 50 mm overall length balances reach with rigidity for secure manual handling. At just 0.012 kg, the component is easy to position and manoeuvre, yet heavy enough to feel substantial. Delivery in a protective case simplifies transport and storage, helping to prevent dings and preserving the calibrated surface under routine workshop conditions. Integrating the pin into quality workflows This precision pin is suitable for end‑measure and tactile verification tasks, offering a simple but effective instrument for checking bores, fits and gauge interfaces. As a single test pin it complements pin sets and ring gauges or can be used as a reference in fixture checks. The compact format makes it straightforward to include in inspection kits and to carry between workstations. Traceability is supported through the product identifiers included in the technical data, which aid inventory control and documentation of inspection tools within a quality management system. Practical advantages that matter on the shop floor Choosing a workshop‑grade precision pin simplifies daily inspection routines: reduced measuring uncertainty leads to faster decisions and fewer follow‑up measures. The robust construction and tight tolerance make this pin a dependable reference for go/no‑go checks and dimensional spot checks. The combination of precision, durability and protective packaging gives consistent performance across shifts, helping maintain throughput without compromising measurement reliability. For critical end‑measure tasks, specify the Metav IndustryLine M323.531 gauge pin for dependable workshop performance — contact Metav Werkzeuge for product advice or to confirm stock availability via info@metav-werkzeuge.com or +49 2822 7131930 Technical data SKU: M323.531 GTIN: 4061905060885 Manufacturer: Metav IndustryLine Core measurements Diameter: 5.31 mm Length: 50 mm Tolerance / Accuracy: ±0.001 mm Weight: 0.012 kg Special features Workshop version Material: special steel Supplied in protective case Category: Gauge pins FAQ What tolerance does this gauge pin offer? The M323.531 gauge pin (Metav IndustryLine) is specified with a tolerance of ±0.001 mm, making it suitable for high‑precision end‑measure checks. Can the pin be used for bore verification and fit checks? Yes. The precision test pin is designed for tactile verification of bores and fits and can be used alongside ring gauges and inspection fixtures. What material is the pin made from? This Metav IndustryLine test pin is manufactured from special steel to provide wear resistance and dimensional stability under frequent use. Is the pin supplied ready for transport and storage? The M323.531 is supplied in a protective case to secure the measuring surfaces during transport and storage. How compact is the pin for handling on the shop floor? With a length of 50 mm and a weight of 0.012 kg, the pin is compact and easy to handle for manual inspection tasks. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
5.32mm Gauge Pin ±0.001 mm Length 50 mm Workshop Version - Metav IndustryLine
Combine the high repeatability of a compact diameter with sub‑micrometre tolerance for dependable end‑measure checks; the pin’s ±0.001 mm accuracy, 5.32 mm diameter and 50 mm length support precise fixture set‑up and quality control. Order the gauge pin directly via Metav Werkzeuge or ask our consultants if needed. Gauge pin M323.532 – 5.32 mm, ±0.001 mm, 50 mm length (Metav IndustryLine) The gauge pin M323.532 is a workshop‑grade precision plug designed for end‑measure checks, fixture alignment and dimensional verification in metalworking and precision engineering. High precision ±0.001 mm tolerance Diameter 5.32 mm for precise fit 50 mm length for fixture and end‑measure Workshop‑grade special steel construction Accuracy that stabilises inspection results High reproducibility is the core asset of this precision pin. The ±0.001 mm tolerance corresponds to sub‑micrometre control that reduces uncertainty when verifying bore sizes or verifying end dimensions. In practice, this level of accuracy helps to detect marginal deviations early, lowering scrap rates and limiting rework. The result is a measurable gain in process reliability and a clearer basis for pass/fail decisions in production measurement routines. Robust design for frequent workshop use Constructed from special steel, the pin is intended for repeated handling and routine inspection tasks common in workshop environments. The 50 mm shaft length balances accessibility with secure seating in gauging fixtures, while the compact 5.32 mm diameter fits into small bores and locating features without compromising stiffness. The workshop‑grade finish provides consistent surface contact during measuring cycles and supports long‑term dimensional stability under normal operational handling. Practical deployment and measurement contexts This precision pin is suitable for end‑measure checks, fixture set‑up and dimensional verification of small to medium bores where a tight diameter tolerance is critical. Lightweight at approximately 0.012 kg, the pin is easy to position and manoeuvre during repeated checks. In quality control workflows it serves as a stable reference for comparative gauging and for confirming finish sizes after machining operations, helping to maintain traceability in inspection records. For workshop‑grade precision and reliable traceability, request the M323.532 gauge pin from Metav Werkzeuge in Emmerich or contact our technical team at info@metav-werkzeuge.com / +49 2822 7131930 Technical data Article number: M323.532 GTIN: 4061905060892 Material: Special steel Special feature: Workshop version Accuracy: ±0.001 mm Facts Diameter: 5.32 mm Length: 50 mm Weight: 0.012 kg Special features Single gauge pin design SKU: M323.532 Eclass: 21170231 FAQ What tolerance can be expected from this gauge pin? The M323.532 gauge pin is specified with a tolerance of ±0.001 mm, making it suitable for sub‑micrometre end‑measure verification. Which materials is the pin made from? The pin is made from special steel, selected for consistent contact behaviour and durability in routine workshop measurement tasks. Is this gauge pin suitable for small‑bore checks and fixture setup? Yes, the 5.32 mm diameter and 50 mm length make the pin well suited to small‑bore verifications and for use as a locating or reference element in fixtures. How heavy is the gauge pin and does weight affect handling? At approximately 0.012 kg, the pin is lightweight, which simplifies manual positioning during repeated measurement operations. Does the product data indicate delivery with a calibration certificate? No factory calibration or calibration certificate is specified in the provided product data for this gauge pin Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
5.33mm Precision Test Pin ±0.001 mm Length 50mm Workshop Version - Metav IndustryLine
Benefit from workshop‑grade construction, an exact ±0.001 mm tolerance and a stable 50 mm length to reduce inspection variability; order the M323.533 directly via Metav Werkzeuge or consult our specialists for application advice. M323.533 Gauge pin (single) — 5.33 mm, ±0.001 mm, 50 mm length (Metav IndustryLine) The M323.533 gauge pin is a workshop‑grade cylindrical test pin designed for end‑measure verification and plug‑gauge checks in precision inspection and final control processes. Workshop‑grade test pin, hardened special steel Diameter 5.33 mm with ±0.001 mm tolerance Length 50 mm for stable insertion and control Single item for precision end‑measure checks Precision that reduces inspection uncertainty The cylindrical test pin delivers a ±0.001 mm tolerance on a 5.33 mm diameter, providing reproducible reference measurements for tight acceptance criteria. Such accuracy minimises pass/fail ambiguity during final inspection, allowing measurable confidence when verifying bore sizes or end‑dimensions. By using a hardened, dimensionally stable pin as a reference, metrology processes become more efficient: fewer retests are required and process capability can be assessed with greater statistical certainty. This direct performance advantage supports faster decision‑making on the shop floor and reduces downtime caused by uncertain measurements. Durable construction for reliable workshop use Constructed from special steel in a workshop‑grade finish, the pin combines wear resistance with practical handling characteristics. With a 50 mm length and a light mass of approximately 0.012 kg, the item remains easy to position while offering sufficient engagement depth for secure measurement. The robust material choice resists deformation over repeated cycles, which preserves dimensional integrity and extends service life in daily inspection routines. As a single‑piece test artefact, it integrates neatly into bench kits and inspection trays, providing a dependable physical reference without elaborate fixturing. Seamless integration into quality workflows Designed for end‑measure applications and plug‑gauge checks, this test pin supports traceable comparative measurements in production and final control. The precise diameter and tight tolerance suit it for monitoring machining drift and for acceptance testing of mating bores. Supplied as an individual gauge pin, it is particularly appropriate where a specific nominal size is required as a reference artefact. For specialised setups or batch inspection strategies, Metav IndustryLine expertise can advise on best practice for calibration intervals and handling to preserve accuracy over time. Contact Metav Werkzeuge today for tailored advice on integrating Metav IndustryLine precision gauge pins into inspection routines; call +49 2822 7131930 or email info@metav-werkzeuge.com Technical data Article number: M323.533 GTIN: 4061905060908 Manufacturer: Metav IndustryLine Category: Gauge pin / Test pin Facts Diameter: 5.33 mm Length: 50 mm Tolerance: ±0.001 mm Weight: 0.012 kg Special features Workshop version Material: Special steel Single piece supply Application: end‑measure verification FAQ What tolerance does this test pin offer? The M323.533 gauge pin provides a ±0.001 mm tolerance, suitable for high‑precision end‑measure verification and tight acceptance checks. Is the pin suitable for plug‑gauge and bore checks? Yes, the single Metav IndustryLine test pin is designed for plug‑gauge checks and for comparative verification of bore diameters during final inspection. What material is the gauge pin made from? The pin is manufactured from special steel, offering enhanced wear resistance and dimensional stability for repeated workshop use. How deep should the pin be inserted for stable measurement? With a 50 mm length, engagement should ensure a firm seating without excessive overhang; this length balances insertion depth and handling stability for routine checks. Metav IndustryLine: Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
5.34mm Test Pin ±0.001mm Length 50mm Workshop Version - Metav IndustryLine
Benefit from ±0.001 mm repeatability, a 50 mm working length and rugged workshop construction for reliable end‑measure checks. Combine high metrology accuracy with durable materials and protected transport to keep inspection routines stable — order via Metav Werkzeuge or contact our consultants for specification support. Test Pin M323.534 — 5.34 mm, ±0.001 mm, 50 mm length (Metav IndustryLine) The Test Pin M323.534 is a workshop‑grade gauging pin designed for precise end‑measure verification and dimensional control in production and inspection environments ±0.001 mm precision (1 µm) for accurate gauging Workshop‑grade construction for daily industrial use Made from special steel for wear‑resistant service Supplied in protective transport case High-precision gauging that reduces rework and scrap The M323.534 is a purpose‑built gauging pin offering a tolerance of ±0.001 mm, which corresponds to 1 µm resolution. This level of precision is directly relevant to modern quality control where dimensional deviations translate into costly rework — the tight tolerance enables reliable go/no‑go assessments and supports statistical process control. The compact 5.34 mm diameter and 50 mm overall length suit fine end‑measure checks and fit standard pin blocks and fixture holes, making the pin a practical tool for batch sampling and final inspection. By specifying a calibrated, workshop‑ready pin, measurement uncertainty is minimised and traceability is maintained across inspection logs. Designed for regular shopfloor use with robust materials Constructed in a workshop‑execution, the pin is manufactured from special steel selected for wear resistance and dimensional stability. The material choice reduces profile wear during repeated insertion and extraction cycles, extending service life in continuous production contexts. The modest mass of the pin allows easy handling while the hardened surface preserves the gauge diameter under routine stresses. For transport and protection, the pin is supplied in a protective transport case, preventing damage and contamination between uses and simplifying storage within inspection kits. This pragmatic design supports daily metrology workflows without sacrificing repeatability. Practical integration into quality routines and traceability Traceability and clear identification are enabled via the product SKU and GTIN for inventory and calibration records, aiding audit readiness. As a single‑piece gauging solution, the pin integrates easily into dimensional checklists, assembly jigs and plug‑gauge arrays for end‑measure verification ("end masses"). Its workshop specification makes it suitable for use at in‑process control points where fast, unequivocal results are required. The combination of precise tolerance, durable construction and protected delivery reduces downtime from faulty gauges and supports consistent production quality across shifts. Contact Metav Werkzeuge today for availability and guidance on implementing the M323.534 in your inspection process — expert advice and local stock support from Emmerich are available to ensure the right gauging solution for every application. Technical Data Article number: M323.534 GTIN: 4061905061110 Label: Prüfstift, einzeln, 5,34mm, +/- 0.001 mm Länge 50 mm Category: Messstifte Data Diameter: 5.34 mm Length: 50 mm Tolerance: ±0.001 mm Weight: 0.012 kg Special features Workshop execution Material: Special steel Supplied in protective transport case Application: End‑measure verification FAQ What accuracy can be expected from this gauging pin? The M323.534 offers an accuracy of ±0.001 mm (1 µm), suitable for fine dimensional checks and strict quality control tolerances. Is the pin suitable for routine workshop use? Yes, the workshop‑grade construction and special steel composition make it durable for daily insertion and extraction cycles in production environments. How is the product delivered? The gauging pin is supplied in a protective transport case to prevent damage during storage and transit. Can this pin be used for end‑measure checks in fixtures? The 5.34 mm diameter and 50 mm length are compatible with standard pin blocks and fixtures used for end‑measure verification and assembly checks. How can the M323.534 be identified for inventory and calibration records? Identification is via the SKU M323.534 and GTIN 4061905061110, facilitating traceability in inspection and calibration documentation. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
5.35mm Gauge Pin 50mm Length ±0.001 mm Workshop Version - Metav IndustryLine
Take advantage of the combination of pinpoint accuracy, compact design and robust workshop execution for reliable end‑dimension verification. With a firm 5.35 mm diameter and an ultra‑tight ±0.001 mm tolerance over a 50 mm length, this inspection pin ensures repeatable results and streamlined quality checks; order the part directly via Metav Werkzeuge or consult the specialists when bulk needs or matching gauges are required. M323.535 gauge pin — 5.35 mm, ±0.001 mm, 50 mm length (Metav IndustryLine) A M323.535 gauge pin for precise end‑dimension verification and small‑bore inspection, supplied as a single inspection pin in a workshop execution suited to routine metrology tasks *Precision diameter 5.35 mm, tolerance ±0.001 mm *Length 50 mm for consistent end‑dimension checks *Made from special steel for durable wear resistance *Workshop version for robust everyday metrology Dependable precision where it matters The compact inspection pin is engineered for repeatable end‑dimension checks and small bore verification. With a nominal diameter of 5.35 mm and a verified tolerance of ±0.001 mm, the pin provides a stable reference for production control and acceptance testing. Its tight tolerance reduces uncertainty in assembly and calibration routines, enabling faster decision‑making and fewer reworks. The single‑piece supply simplifies inventory management where small, exact standards are needed for frequent checking of mating bores and fitted parts. Built for routine use in workshops and inspection benches Constructed from special steel, this inspection pin resists surface wear and preserves form over repeated insertions and withdrawals. The 50 mm length offers a reliable engagement depth for many common components without excess overhang, reducing the risk of bending or misalignment. The workshop design emphasises robustness and handling convenience during repetitive metrology tasks, so measuring cycles remain consistent and operator variability is minimised. These attributes support efficient quality workflows on the shop floor and in inspection areas. Practical integration and benefits for quality processes Using a standardised inspection pin speeds up go/no‑go checks and reduces measurement setup time, contributing to smoother production flow and lower inspection costs. The compact mass (approx. 0.012 kg) facilitates safe handling and quick placement into fixtures or test blocks. For traceability and procurement, the item is listed under the Metav IndustryLine offering and fits straightforwardly into parts lists for tooling and verification equipment. Its clear, technical specification simplifies procurement decisions and ensures compatibility with existing measurement procedures. Secure precision supplies through Metav Werkzeuge — contact our specialists for availability, matching gauge sets and procurement advice to fit specific production needs Technical Data Article number: M323.535 GTIN: 4061905057908 Material: Special steel Weight: 0.012 kg Feature: Workshop execution Type: Single inspection pin Facts Diameter: 5.35 mm Tolerance: ±0.001 mm Length: 50 mm Special features Designed for end‑dimension and bore verification Robust surface for repeated use Supplied as a single unit Category: Gauge pin / inspection pin FAQ What is the exact diameter and tolerance of this gauge pin? The gauge pin has a nominal diameter of 5.35 mm with a tolerance of ±0.001 mm, as specified for the M323.535. For which applications is this inspection pin suitable? It is intended for end‑dimension checks and small‑bore inspection, providing a reliable reference for production control and assembly verification. What material is used and how durable is the pin? The pin is made from special steel, selected for wear resistance and dimensional stability during frequent checking cycles. Is the item supplied as a single piece or in sets? This product is supplied as a single inspection pin (single unit), listed under the SKU M323.535. Metav IndustryLine: Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
5.36mm Gauge Pin, ±0.001mm, 50mm Length, Workshop Version, Special Steel, Supplied In Case - Metav IndustryLine
Take advantage of the exceptional form accuracy and stable workshop construction to speed up routine inspections and reduce scrap rates; the combination of ±0.001 mm tolerance, 5.36 mm diameter and a 50 mm length makes this an efficient specialist gauge for small-bore verification. Order the gauge pin directly via Metav Werkzeuge or consult our advisors for application guidance. Gauge pin M323.536 — 5.36 mm diameter, ±0.001 mm tolerance (Metav IndustryLine) A gauge pin designed for precision end‑measurements and go/no‑go checks in workshop environments, offering a compact 50 mm length and workshop-grade finish for everyday use High-precision ±0.001 mm tolerance Diameter 5.36 mm, length 50 mm Special steel for wear resistance Workshop design for regular inspection tasks Precision that shortens inspection cycles The ±0.001 mm accuracy of this gauge pin ensures repeatable results when checking bore sizes, plug fits or setting up fixtures. A tolerance at this level translates into reliable pass/fail decisions and reduces downstream rework; in practice, fewer ambiguous measurements mean faster throughput on assembly and inspection tables. The compact diameter of 5.36 mm and the 50 mm shank length keep handling simple while preserving the contact geometry needed for consistent results. Durable construction for daily workshop use Manufactured from special steel, this workshop model balances wear resistance with manageable mass, supporting frequent handling without rapid surface degradation. The construction keeps concentricity and roundness stable over many cycles, which in turn maintains measurement certainty and extends service intervals. At roughly 0.012 kg per item, the pin is easy to manipulate for repetitive checks, yet substantial enough to avoid bending under normal use. Designed for practical metrology workflows As a single, purpose-made gauge pin, the item is ideal for quick verification tasks, alignment of assembly jigs and comparative checks against master gauges. The simple design integrates seamlessly into standard inspection routines and complements digital or analogue measurement setups used in metrology departments. Metav’s role as a European quality filter contributes to consistent product quality and makes this specialist tool a pragmatic addition to workshop instrumentation, delivering confidence where small tolerances matter For workshop-grade precision, contact Metav Werkzeuge to discuss the Metav IndustryLine gauge pin M323.536 and secure the most suitable supply and delivery options from our Emmerich centre Technical data Article number: M323.536 GTIN: 4061905057915 Brand: Metav IndustryLine Facts Diameter: 5.36 mm Length: 50 mm Tolerance: ±0.001 mm Weight: 0.012 kg Special features Material: Special steel Version: Workshop execution Packaging: Supplied individually Category: Gauge pins FAQ What is the declared tolerance for this gauge pin? The gauge pin M323.536 is specified with a tolerance of ±0.001 mm, suitable for fine inspection and functional checks. Which materials is the pin suitable for checking? This pin is a dimensional standard used to verify holes and fittings in common engineering materials; the product data specify its geometric purpose rather than application‑specific cutting behaviour. Is the item supplied as part of a set or individually? The M323.536 is supplied as a single gauge pin, designed for standalone use in inspection or as an addendum to existing gauge sets. How should the pin be stored to retain accuracy? Keep the pin clean and dry, store it in a protective tray or drawer and avoid impacts; maintaining surface condition preserves the declared form and tolerance. Can this pin be used for calibration or as a reference standard? The pin serves as a dimensional verification tool; for use as a certified reference standard, please refer to specific calibration documents or product listings that state a calibration certificate. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
5.37mm Test Pin ±0.001 mm Length 50 mm Workshop Version Plastic Case - Metav IndustryLine
Taking advantage of ultra‑fine tolerance and a robust workshop design ensures reproducible end‑measure checks and fewer rejected parts; combine ±0.001 mm accuracy with a compact 5.37 mm diameter and order directly via Metav Werkzeuge or consult our specialists for application advice. Gauge pin M323.537 — precision 5.37 mm, ±0.001 mm (Metav IndustryLine) The gauge pin M323.537 is a single precision test pin for end‑measure verification and fit checks in workshop metrology High precision ±0.001 mm tolerance Diameter 5.37 mm for end‑measure fits Compact 50 mm length for tight assemblies Delivered in a protective case Reduced rework through measurable precision The core benefit of this gauge pin is its high repeatability, achieved by a specified tolerance of ±0.001 mm. Such fine accuracy supports reliable go/no‑go decisions during incoming inspection and production sampling, reducing rework and downtime. The precise diameter control minimises measurement scatter, so process control charts reflect actual production quality rather than instrument variation. Dependable fit verification for mating parts With a 5.37 mm diameter manufactured to a tight tolerance, the pin is ideal for end‑measure checks where a defined plug gauge is required. Using a discrete reference pin instead of improvised tools speeds up pass/fail checks on housings, bores and dowel locations. The compact geometry enables insertion into shallow bores and small assemblies, making it suitable for precision components in tooling and fixtures. Robust workshop design built for daily use Constructed from special steel and specified as a workshop version, the pin resists wear while remaining economical for routine use. The 50 mm working length balances handling and stability, allowing single‑handed positioning without compromising stiffness. Hardwearing material and careful finishing preserve diameter integrity across numerous cycles, extending useful life under regular shopfloor conditions. Practical handling and protective storage Delivered as a single piece and supplied in a protective case, the pin is ready for secure storage and safe transport between workstations. The protective case reduces contamination and prevents damage to the measuring surface, which is essential given the ±0.001 mm tolerance. Lightweight handling characteristics support quick checks on the production line or in assembly stations without adding bulk to inspection kits. Seamless integration into inspection routines The pin complements existing dimension control methods and can be introduced into first‑article inspection, batch sampling or fixture calibration procedures. Its repeatable geometry supports traceable measurements when recorded against inspection protocols, helping to document conformity and to streamline quality reports. Use as a reference gauge to spot deviations early and maintain production throughput. Proven distribution and support from Metav IndustryLine Choosing this precision pin means partnering with a supplier that promotes the democratisation of precision: Metav IndustryLine couples a wide product range with dependable logistics from Emmerich. The brand’s commitment to reliable supply and transparent handling helps workshops and industry buyers reduce supplier complexity while maintaining measurement integrity. Contact Metav Werkzeuge today for tailored advice on integrating this Metav IndustryLine gauge pin into inspection workflows and to confirm availability with the Emmerich warehouse via info@metav-werkzeuge.com or +49 2822 7131930 Technical data Article number: M323.537 GTIN: 4061905057922 Eclass: 21170231 Facts Diameter: 5.37 mm Tolerance: ±0.001 mm Length: 50 mm Weight: 0.012 kg Special features Material: Special steel Workshop version Delivered in protective case Single gauge pin FAQ What materials is this pin made from? The gauge pin is made from special steel; the material gives durability for routine workshop use and preserves the ±0.001 mm diameter accuracy of M323.537 (Metav IndustryLine). Is the pin supplied ready for inspection use? Yes. The M323.537 is supplied as a single piece and delivered in a protective case for safe storage and immediate use in inspection and assembly tasks. Can this pin be used for shallow bores and small fixtures? The compact 50 mm length and 5.37 mm diameter make it suitable for shallow bores, dowel checks and small fixture verification where a short reference pin is required. How does this pin help with process control? Using the gauge pin as a repeatable reference reduces measurement scatter and supports consistent go/no‑go decisions, improving data reliability in quality documentation. Is the M323.537 intended for heavy production environments? The workshop version is designed for regular shopfloor checks; its special steel construction offers a balance between durability and cost‑efficient replacement when required. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
5.38mm Precision Gauge Pin ±0.001mm Length 50mm, Workshop Version - Metav IndustryLine
Take advantage of the combination of pinpoint dimensional control, compact handling and workshop‑grade durability to streamline end‑measure checks and assembly inspections; order the item directly via Metav Werkzeuge or consult the Metav technical team for application advice. M323.538 Gauge Pin — 5.38 mm diameter, ±0.001 mm tolerance (Metav IndustryLine) M323.538 gauge pin is a single workshop‑grade inspection pin designed for precise end‑measure verification and fit testing in production and bench‑level inspection workflows. Workshop version for everyday shop use Diameter 5.38 mm for precise fit Tolerance ±0.001 mm for high accuracy Length 50 mm, compact inspection pin Precision that reduces rework and speeds decision making The compact inspection pin delivers ±0.001 mm positional certainty for critical passing checks and dimensional verification. With a nominal diameter of 5.38 mm, this pin supports repeatable go/no‑go assessments and fine adjustment of fixtures where small deviations have large consequences. The exceptionally tight tolerance translates into fewer rejects and reduced rework, enabling faster throughput on small batches and high‑mix production runs while maintaining traceable results. Durable workshop design for regular handling Manufactured in special steel and finished as a workshop version, the pin balances wear resistance with practical handling. The 50 mm shaft length and low mass (approx. 0.012 kg) make the component easy to position in confined measuring setups and quick to manoeuvre during serial checks. Robust material choice and shop‑oriented finishing preserve the critical diameter over repeated seating cycles, extending service intervals and ensuring consistent mating with mating bores and gauges. Designed to integrate into inspection processes and fixtures As a single inspection element, the pin is suitable for end‑measurement, assembly clearance checks and precision fit trials in both manual and semi‑automated routines. Its compact format supports use in fixture pockets, datum checks and end‑face gauges where space is limited. Paired with calibrated masters or block sets, the pin contributes to a reproducible quality workflow and straightforward documentation of measurement results, supporting informed quality decisions on the shop floor. Choose the Metav IndustryLine M323.538 gauge pin for consistent end‑measure control — contact Metav Werkzeuge in Emmerich for tailored advice and dependable supply Technical data Article number: M323.538 GTIN: 4061905057939 Category: Messstifte (gauge pins) Manufacturer: Metav IndustryLine Facts Diameter: 5.38 mm Length: 50 mm Tolerance: ±0.001 mm Weight: 0.012 kg Special features Material: special steel Workshop execution Single inspection pin for end‑measure and fit testing FAQ What are the exact diameter and tolerance of this gauge pin? The M323.538 gauge pin has a diameter of 5.38 mm with a tolerance of ±0.001 mm for high‑precision checks. Which applications is this inspection pin suited to? This inspection pin from Metav IndustryLine is intended for end‑measure verification, clearance and fit tests, and routine dimensional checks in workshop and production environments. What is the pin made from and how does that affect durability? The M323.538 is manufactured from special steel; this material choice improves wear resistance and maintains the critical diameter under repeated use. Can the pin be used in fixture pockets and confined inspection setups? Yes — the compact 50 mm length and low weight make the pin suitable for fixture pockets, datum checks and tight measuring arrangements. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
5.39mm Test Probe, Single, ±0.001mm Accuracy, Length 50mm, Workshop Version - Metav IndustryLine
Combining micrometric tolerance of ±0.001 mm, a precise 5.39 mm diameter and a robust 50 mm length, this single gauge pin delivers repeatable end‑measure checks in workshop and inspection routines; order via Metav Werkzeuge or consult our specialists for application advice. M323.539 gauge pin — 5.39 mm diameter, ±0.001 mm accuracy (Metav IndustryLine) The M323.539 is a single gauge pin designed for accurate end‑measure verification and bore checking in workshop and metrology settings. High precision ±0.001 mm tolerance Diameter 5.39 mm for end‑measure checks 50 mm hardened special steel length Supplied in protective transport case Consistent, micrometric accuracy for inspection tasks The primary benefit of this gauge pin is its ±0.001 mm rated tolerance, which supports tight acceptance criteria and helps reduce false rejects during quality control. Built for measurement use rather than machining, the pin’s nominal 5.39 mm diameter and short 50 mm shank reduce flex and contact variation, enabling repeatable go/no‑go or reference checks. In plain terms, the fine tolerance means that small deviations in component bores can be detected reliably, making the part suitable for precision tasks such as final bore verification and end‑dimension control. Durable workshop design that keeps handling simple Constructed from special steel and specified as a workshop version, the pin balances surface hardness and corrosion resistance for everyday use at the bench. The 50 mm length provides a practical working reach while remaining stiff under hand inspection, so single‑operator checks are straightforward. Supplied in a protective transport case, the pin arrives ready for safe storage and transport between inspection points; this reduces the risk of surface damage that would otherwise affect measurement certainty. Practical integration into measurement routines The gauge pin serves as a compact reference for quick dimensional checks, comparing measured bores or fit conditions against the pin’s nominal size. Its compact form factor and workshop specification suit routine in‑process controls and final inspections where rapid verification of end dimensions is required. As a single, calibrated tool is not declared in the product data, this pin is best used alongside established calibration schedules and reference standards maintained by the inspection department to preserve long‑term traceability. Contact Metav Werkzeuge for application guidance or to secure the Metav IndustryLine M323.539 for your inspection bench — our Emmerich team can advise on storage, calibration paths and compatible inspection routines Technical data Article number: M323.539 GTIN: 4061905057946 ECLASS: 21170231 Core data Diameter: 5.39 mm Length: 50 mm Tolerance: ±0.001 mm Weight: 0.012 kg Special features Material: Special steel Workshop version Supplied in transport case FAQ What is the intended use of this gauge pin? The M323.539 gauge pin is intended for end‑measure verification and bore checks where a precise reference diameter of 5.39 mm is required. Is the M323.539 supplied with a calibration certificate? The product data does not state a calibration certificate; calibration and traceability should be handled according to the purchaser’s inspection procedures. Can this pin be used for go/no‑go testing? Yes, the pin’s tight tolerance and defined nominal diameter make it suitable as a reference for go/no‑go or fit checks in workshop inspection routines. How should the gauge pin be stored to retain accuracy? Store the gauge pin in its protective transport case and keep it in a stable, low‑humidity environment; handle with clean hands or gloves to avoid surface contamination. Is the M323.539 suitable for field use in a production environment? The workshop specification and transport case make the pin suitable for routine checks on the shop floor, provided standard care and scheduled recalibration are observed. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
5.3mm Gauge Pin Single, ±0.001mm, Length 50mm, Workshop Version - Metav IndustryLine
Benefit from a compact inspection solution that combines ±0.001 mm tolerance, a 5.30 mm diameter and a robust 50 mm length for reliable end‑dimension checks; order directly via Metav Werkzeuge or consult our technical advisors for specification matching. M323.530 Gauge Pin — Precision Test Pin, 5.30 mm, ±0.001 mm, 50 mm (Metav IndustryLine) A M323.530 precision gauge pin designed for end‑measurement and inspection tasks in workshop metrology, ideal where micron‑level repeatability is required Precision tolerance ±0.001 mm Diameter 5.30 mm, length 50 mm Workshop version in special steel Deliver reproducible fits with micron accuracy A gauge designed for exacting inspection routines, the gauge pin gives a guaranteed tolerance of ±0.001 mm, equivalent to 1 µm, which is suitable for critical go/no‑go checks and reference measurements. This resolution reduces uncertainty when verifying bores, plug fits or final dimensions and supports consistent assembly quality. The narrow tolerance is particularly valuable for small mechanical parts and precision jigs where even slight deviations affect function. Built for workshop handling and durability Constructed from special steel in a workshop specification, the inspection pin balances surface integrity with day‑to‑day usability. The compact 50 mm length and 5.30 mm diameter provide a stable contact area while remaining easy to position in fixtures or measurement aids. Supplied in a protective transport case, the single test pin stays protected during storage and transit, preserving its measuring edge and surface finish for repeatable use. Integrates smoothly into measurement workflows The single‑piece test pin is suited for use as a reference gauge in tactile and optical measurement setups, and for manual inspection with micrometres, height gauges or comparator benches. The M323.530 test pin is also practically useful when establishing reference limits in fixture set‑up or when checking mating components during final inspection. Its compact form factor supports quick handling and short cycle inspection without compromising accuracy. Traceability and clear identification for procurement Identification is simplified with the SKU M323.530 and GTIN 4061905060878, enabling straightforward inventory and procurement processing. The low mass (approx. 0.012 kg) and workshop design make this inspection pin a practical choice for toolrooms and quality departments seeking a reliable, repeatable gauge for end‑dimension verification. Order the M323.530 gauge pin via Metav Werkzeuge for workshop‑ready precision; contact our specialists in Emmerich for tailored advice and specification support Technical Data Article number: M323.530 GTIN: 4061905060878 SKU: M323.530 Facts Diameter: 5.30 mm Tolerance: ±0.001 mm Length: 50 mm Weight: 0.012 kg Material: Special steel Special features Workshop version Supplied in protective transport case Single test pin for end‑measurements FAQ What accuracy does this inspection pin provide? The inspection pin offers an accuracy of ±0.001 mm (1 µm), suitable for fine tolerance checks and precision fitting controls. Can the pin be used for bore checking and plug fits? Yes, the M323.530 gauge pin is intended for end‑dimension verification, bore checking and plug‑fit assessments in workshop and production environments. What is the material and is it suitable for everyday workshop use? The pin is made from special steel and supplied in a workshop specification, making it suitable for routine metrology tasks while retaining dimensional stability. Is the pin supplied individually or in sets? This listing describes a single test pin supplied individually in a protective transport case for secure handling and storage. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
5.41mm Gauge Pin Single, ±0.001mm, Length 50mm, Workshop Version - Metav IndustryLine
The robust workshop version delivers a 5.41 mm reference diameter with a ±0.001 mm tolerance and a 50 mm shaft that provides repeatable end‑measure checks; order the pin via Metav Werkzeuge or request advice from our consultants for application-specific selection. M323.541 gauge pin — 5.41 mm diameter, ±0.001 mm accuracy, Metav IndustryLine The M323.541 gauge pin is a workshop‑grade precision pin designed for end‑measure verification, fixture alignment and reference checks in inspection and jigging tasks. ±0.001 mm tolerance for high-precision checks Workshop-grade construction in special steel 5.41 mm diameter for standard end‑measure gauges 50 mm length suited to fixture and gauge use Reduce measurement uncertainty with a calibrated reference The M323.541 functions as a reliable reference dowel for inspection routines where repeatable reference points are required. Its ±0.001 mm accuracy reduces measurement uncertainty in pass/fail checks and comparative gauging, helping to shorten inspection cycles and avoid unnecessary rework. Using a dedicated precision pin as a fixed datum simplifies gauge set‑up and ensures consistent results across multiple shifts, which is particularly useful when several operators share the same test benches or fixtures. Durable design for frequent workshop handling Built in a workshop‑grade specification from special steel, this test pin is designed to resist wear under regular insertion and withdrawal in jigs and bore gauges. The 50 mm shaft length gives a comfortable engagement depth for most fixture applications while remaining light and easy to handle; the low mass supports quick positioning and reduces operator fatigue during repetitive checks. The material choice balances hardness and toughness so the pin sustains its reference surface over many cycles, extending service life and lowering long‑term tooling costs. Seamless integration into inspection and fixture processes As an end‑measure reference, the pin is suitable for alignment, go/no‑go checks and positional verification in small‑bore applications. Its 5.41 mm diameter matches common bore and plug scenarios, allowing straightforward substitution into existing fixture plates or test rigs without redesign. The compact form factor supports dense fixture layouts and tight access points while keeping the reference geometry stable. For production environments seeking faster in‑line gauging, the pin simplifies fixturing and reduces auxiliary setup time, contributing to higher overall throughput. Contact Metav Werkzeuge in Emmerich to specify the M323.541 gauge pin for your inspection bench—our specialists will advise on fitment and immediate supply; call +49 2822 7131930 or email info@metav-werkzeuge.com Technical Data Article number: M323.541 GTIN: 4061905058844 Brand: Metav IndustryLine Manufacturer: Metav Werkzeuge GmbH Facts Diameter: 5.41 mm Length: 50 mm Tolerance: ±0.001 mm Weight: 0.012 kg Special features Workshop‑grade execution Material: special steel Category: gauge pins / test pins Application hint: end‑measure and fixture reference FAQ What is the intended use for this gauge pin? The gauge pin is intended as a precision reference for end‑measure checks, fixture alignment and pass/fail gauging where a stable datum of 5.41 mm is required. Can the M323.541 be used in production jigs and fixtures? Yes, the M323.541 gauge pin is specifically designed for workshop and production use, offering robust special steel construction suitable for frequent insertion in fixtures. How precise is the diameter of the pin? The pin is specified with a tolerance of ±0.001 mm, providing a high‑precision reference for accurate inspection and comparative measurements. Is the pin compatible with standard bore gauges and plug fixtures? The 5.41 mm diameter and 50 mm length make the pin compatible with common small‑bore fixtures and plug‑type holders used in inspection benches. What benefits does the workshop version provide compared with general‑purpose pins? The workshop version prioritises durability and handling for repeated use in industrial environments, combining a robust material choice with a form factor optimised for fixture integration. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
5.42mm Gauge Pin ±0.001mm Length 50mm Workshop Version - Metav IndustryLine
Take advantage of the combination of ±0.001 mm measurement accuracy, a precise 5.42 mm diameter and a protective transport case to ensure reliable end‑measure checks in everyday workshop metrology; order the gauge pin directly via Metav Werkzeuge or contact our consultants for integration advice. M323.542 Gauge Pin — 5.42 mm, ±0.001 mm (Metav IndustryLine) The M323.542 gauge pin is a single inspection pin for precise end‑measure verification and go/no‑go checks in workshop metrology. Workshop‑grade special steel Diameter 5.42 mm ±0.001 mm 50 mm length for deeper checks Supplied in a transport case Ensure measurement certainty with sub‑micron repeatability The M323.542 is engineered for applications that demand reproducible dimensional verification. With a declared tolerance of ±0.001 mm, this individual gauge pin supports decisive go/no‑go assessments and high‑confidence pass/fail checks on bores, seats and end‑measures. The fine tolerance reduces subjective judgement in manual inspection and helps maintain consistent quality across production batches, improving throughput without sacrificing control. Built for workshop use — durable and easy to handle Constructed from special steel in a workshop specification, the pin resists wear while remaining straightforward to handle during routine checks. Its 50 mm length provides reach for deeper features, while the compact diameter of 5.42 mm suits a wide range of small‑bore checks. Delivered in a protective transport case, the pin is protected in transit and storage, preserving the measuring surface and minimising the need for immediate refurbishment. Integrates smoothly into existing inspection routines Weighing just 0.012 kg and supplied as a single unit, this compact inspection tool is ideal for spot checks, fixture validation and comparative gauging tasks on the shop floor. The clear article identification (SKU M323.542, GTIN 4061905058851) simplifies inventory and traceability. By adding a purpose‑made pin like this to a toolbox, measurement cycles become quicker and non‑conforming parts are detected earlier, reducing rework and supporting a robust quality process. Request tailored advice from Metav Werkzeuge in Emmerich — our metrology specialists will explain how the M323.542 gauge pin fits specific inspection workflows; contact info@metav-werkzeuge.com or call +49 2822 7131930 for personal consultation. Technical data Article number: M323.542 GTIN: 4061905058851 Brand: Metav IndustryLine Category: Gauge pin / Messstift Facts Diameter: 5.42 mm Tolerance: ±0.001 mm Length: 50 mm Weight: 0.012 kg Special features Material: Special steel Workshop execution Supplied in a transport case Single gauge pin SKU: M323.542 FAQ What is the declared accuracy of this gauge pin? The M323.542 gauge pin is specified with an accuracy of ±0.001 mm, suitable for precise go/no‑go checks and end‑measure verifications. Which materials is the pin compatible with for inspection tasks? As a dimensional inspection tool, the pin itself is made from special steel and is intended for checking components regardless of workpiece material; it does not alter the workpiece. Does the product arrive ready for immediate use? The M323.542 is supplied as a single, workshop‑grade gauge pin in a protective transport case and is ready for integration into inspection routines. How should the gauge pin be stored between uses? Store the pin in its supplied transport case to protect the measuring surface from contamination and mechanical damage. Can this pin be used for deeper bore measurements? The 50 mm length provides additional reach for deeper features and is suitable for many shop‑floor bore and end‑measure checks. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
5.43mm Gauge Pin, Single, ±0.001mm, 50mm Length, Workshop Version - Metav IndustryLine
Compact performance and repeatable results: the precision gauge pin M323.543 combines ±0.001 mm dimensional certainty with a Ø 5.43 mm ground shaft and a 50 mm working length, making it ideal for routine verification and in-process checks; order directly via Metav Werkzeuge or consult our specialists for application advice. Precision gauge pin M323.543 – Ø 5.43 mm, ±0.001 mm, 50 mm length (Metav IndustryLine) Precision gauge pin M323.543 is a workshop-grade cylindrical gauge designed for dimensional verification of bores, end measurements and reference checks in production and assembly environments. ±0.001 mm accuracy Ø 5.43 mm ground diameter 50 mm working length Special steel with protective case Sub-micron accuracy for reliable production checks The gauge pin delivers an accuracy of ±0.001 mm, equivalent to 1 μm, which ensures high repeatability when verifying critical diameters. Such sub-micron precision reduces inspection uncertainty and supports tighter process control, making the component suitable for both final inspection and inline checks. The specified tolerance is appropriate for high-precision mechanical assemblies where small deviations can lead to functional issues. Robust workshop design that simplifies handling Manufactured in special steel and supplied as a single-piece, the pin balances rigidity and manageable mass (approx. 0.012 kg) for straightforward handling on the shop floor. The workshop version designation indicates practical finishing and durability for regular use; the item is protected during transport by a protective case, which keeps the gauge pin free from nicks and contamination until first use. The compact 50 mm length supports manual placement and confined-space inspection without compromising stability. Integrates into quality workflows and gaging sets As a precisely ground cylindrical reference, the unit is ideal for comparative checks, seat and bore verification or as a master plug during assembly set-up. The combination of Ø 5.43 mm nominal diameter and close tolerance makes it a reliable reference for go/no-go judgements when paired with calibrated fixtures or visualising equipment. Clear identification (SKU M323.543, GTIN 4061905058868) supports inventory control and traceability within quality management systems, helping to document measurement routines and maintain audit trails. For workshop-ready precision from Metav IndustryLine, contact Metav Werkzeuge to arrange supply of the M323.543 gauge pin or to discuss integration into existing inspection routines: info@metav-werkzeuge.com · +49 2822 7131930 Technical data SKU: M323.543 GTIN: 4061905058868 Manufacturer: Metav IndustryLine Weight: 0.012 kg Facts Diameter: 5.43 mm Accuracy: ±0.001 mm Length: 50 mm Special features Material: Special steel Workshop design Delivered in protective case Single gauge pin FAQ What tolerance does the gauge pin offer? The gauge pin provides an accuracy of ±0.001 mm, suitable for high-precision dimensional checks. Is the pin suitable for routine workshop inspection? Yes, the workshop-grade finish and protective case make the pin well suited to regular use in production and assembly environments. How is the item identified for traceability? The product is listed as M323.543 and carries GTIN 4061905058868 for inventory and audit purposes. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
5.44mm Gauge Pin Precision ±0.001mm Length 50mm Workshop Finish - Metav IndustryLine
Take advantage of ultra‑fine dimensional control combined with workshop‑ready durability: the gauge pin delivers 5.44 mm nominal diameter with ±0.001 mm tolerance and a 50 mm shaft for reliable end‑measurement. Order this precision component directly via Metav Werkzeuge or consult our specialists for application advice. M323.544 Gauge Pin — Gauge pin, 5.44 mm ±0.001 mm, 50 mm length (Metav IndustryLine) M323.544 is a compact gauge pin designed for high‑accuracy end‑measurement and component verification in workshop and inspection environments. Diameter 5.44 mm with ±0.001 mm tolerance 50 mm hardened special‑steel shaft Supplied in protective transport case Measure with micrometre‑grade certainty to cut rejects and rework The M323.544 gauge pin provides a nominal diameter of 5.44 mm with an outstanding ±0.001 mm tolerance, equating to single‑micrometre resolution for go/no‑go checks and reference measurements. Such precision reduces the need for repeat machining and lowers scrap rates by establishing a reliable master datum for bore and plug tests. Calibrated shop gauges at this level support traceable inspection routines and speed up in‑process checks by replacing labour‑intensive comparative methods with a single, verifiable standard. The result is measurable efficiency gains across serial inspection and setup tasks. Solid construction for repeatable contact and long service life Manufactured from special steel and specified at a 50 mm length, the pin balances stiffness with manageable handling in the workshop. The hardened shaft resists wear on the contact surface, preserving the nominal diameter over many insertion cycles and ensuring repeatable measurements. Supplied in a protective transport case, the component stays protected during storage and transit, maintaining surface integrity and dimensional stability. For inspection benches and fixture sets, this combination of material and finish minimises dimensional drift and extends the service interval for reference gauges. Practical fit into inspection workflows and machining checks Designed for straightforward integration into verification routines, the pin is suitable for bore gauging, end‑position references and comparative inspection tasks in metalworking and precision assembly. Its compact form supports rapid manual checks as well as fixture mounting for repetitive tests, helping to shorten NDT and QA cycles. The controlled tolerance makes the pin ideal for final inspection and first‑off checks where tight dimensional control is demanded. For environments that require robust documentation, the pin is compatible with typical metrology documentation practices and can be recorded as a workshop master in quality control logs. Secure robust, micrometre‑grade measurement from Metav IndustryLine — contact Metav Werkzeuge in Emmerich for tailored advice and dependable supply Technical data Article number: M323.544 GTIN: 4061905058875 Brand: Metav IndustryLine Numerical data Nominal diameter: 5.44 mm Length: 50 mm Tolerance: ±0.001 mm Weight: 0.012 kg Special features Material: special steel Workshop version Supplied in protective transport case FAQ What level of precision can be expected from this gauge pin? The M323.544 gauge pin from Metav IndustryLine is specified to ±0.001 mm, providing micrometre‑level precision suitable for fine inspection and reference checks. Is the pin suitable for routine bore gauging in a production environment? Yes, the hardened special steel shaft and the 50 mm length make the M323.544 suitable for repeated bore gauging and fixture use in workshop and light production settings. How is the gauge pin delivered to ensure dimensional protection? Delivery of the M323.544 includes a protective transport case to preserve surface condition and dimensional integrity during storage and transit. Can this pin be used as a master for comparative inspection setups? The dimensional stability and ±0.001 mm tolerance make the M323.544 appropriate as a master gauge for comparative inspections and first‑article verification rounds. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
5.45mm Gauge Pin 50mm Length ±0.001mm Workshop Version - Metav IndustryLine
Precise gauging for consistent inspection results: the workshop‑grade gauging pin combines a 5.45 mm diameter with a tight ±0.001 mm tolerance and a 50 mm length to support repeatable end‑measure checks; supplied as a single pin in a protective case, it is ready for integration into gauging jigs and fixtures. Order the gauging pin directly via Metav Werkzeuge or consult our advisers for specification matching. Gauging pin M323.545 — 5.45 mm diameter, ±0.001 mm accuracy (Metav IndustryLine) A gauging pin M323.545 designed for precise end‑gauge checks and inspection tasks in workshop environments, offering robust workshop‑grade construction for routine production control. ±0.001 mm tolerance Diameter 5.45 mm Length 50 mm workshop version Special steel construction Consistent accuracy for reliable production control The core advantage is measurable: ±0.001 mm tolerance ensures that the pin performs as a fine reference in inspection sequences where small deviations matter. By limiting dimensional variation to one micrometre, the component supports tighter process control and reduces false rejects during incoming inspection or final checks. The small form factor combined with a defined length gives stable seating in gauges, which translates into repeatable measurement results and fewer re‑checks on the shop floor. Built to withstand everyday workshop use Constructed from special steel and specified as a workshop‑grade item, the pin tolerates typical handling and fixture contact without compromising its functional surface. The moderate mass—about 12 g—keeps the pin easy to position in jigs while limiting the influence of inertia during quick checks. Supplied as a single unit in a protective case, the design reduces transport and storage risk, helping to preserve the calibrated geometry that underpins reliable inspection over time. Easy integration into inspection jigs and end‑gauge assemblies With a nominal diameter of 5.45 mm and a 50 mm total length, the pin suits common end‑gauge and go/no‑go assemblies where precise plug‑type references are required. The straight, hardened shaft adapts readily to pinned locating points and can be used as a master for verifying bore sizes, fixture alignment or for checking end‑masses in serial production. Lightweight and compact, the component streamlines fixture changes and keeps cycle time low without sacrificing measurement confidence. For dependable end‑measure control choose the Metav IndustryLine gauging pin M323.545 — contact Metav Werkzeuge for tailored advice and reliable supply from Emmerich. Technical data Article number: M323.545 GTIN: 4061905058882 Manufacturer: Metav IndustryLine Facts Length: 50 mm Diameter: 5.45 mm Tolerance: ±0.001 mm Weight: 0.012 kg Special features Workshop version Material: special steel Supplied as single pin Delivered in protective case Intended for end‑gauge and inspection use FAQ What tolerance does the gauging pin provide? The gauging pin M323.545 from Metav IndustryLine is manufactured to a tolerance of ±0.001 mm. What are the pin's main dimensions? The pin has a nominal diameter of 5.45 mm and a total length of 50 mm; weight is approximately 0.012 kg. What material is the pin made from? The pin is produced from special steel, specified for workshop durability and stable dimensional performance. How is the product supplied? The product is supplied as a single gauging pin in a protective case for transport and safe storage. Which inspection tasks is the pin suited to? Typical uses include end‑gauge checks, go/no‑go verifications and fixture alignment where a precise plug‑type reference is required. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
5.46mm Gauge Pin, Workshop Version, ±0.001mm Accuracy, 50mm Length - Metav IndustryLine
Take advantage of the combination of micron-level accuracy, compact dimensions and robust workshop design for reliable end‑measure inspections; order the precision gauge pin directly via Metav Werkzeuge or consult our specialists for application advice. Precision Gauge Pin M323.546 – 5.46 mm, ±0.001 mm (Metav IndustryLine) A Precision Gauge Pin M323.546 for high‑accuracy end‑measure checks and plug‑fit verification in workshop environments Tolerance ±0.001 mm Diameter 5.46 mm precision Length 50 mm workshop version Supplied in protective case High‑accuracy inspection where every micron counts The M323.546 is a precision gauge pin engineered for applications that demand repeatable results at the micrometre scale. With a claimed tolerance of ±0.001 mm (one micrometre), this inspection pin reduces uncertainty in go/no‑go and end‑dimension checks, enabling faster acceptance decisions and fewer reworks. The small nominal diameter of 5.46 mm and compact form factor make it ideal for tight fits and detailed assembly checks in small components, where conventional measuring tools can be cumbersome. Robust workshop design and convenient handling Manufactured in a workshop version, the pin combines compactness with practical resilience for day‑to‑day use. The 50 mm length provides a secure seating and comfortable handling during tactile measurements, while the construction from special steel ensures dimensional stability under normal workshop loads. Delivery in a protective case simplifies storage and transport and helps keep the gauge pin free from contamination and incidental damage between uses, maintaining its measurement integrity over time. Practical use cases and process benefits This precision pin suits final inspection, plug‑gauge checks and reference comparisons in small‑part production, metrology benches and laboratory settings. Integrating the M323.546 into routine quality checks shortens inspection cycles and supports traceable results for batch documentation. The compact dimensions favour work on delicate parts and assemblies where access is limited, and the clear specification of ±0.001 mm allows production engineers to define realistic tolerances and error budgets in process control. For dependable end‑measure verification, request the M323.546 precision gauge pin from Metav Werkzeuge or contact our Emmerich specialists for tailored measurement advice Technical data Article number: M323.546 GTIN: 4061905058899 Eclass: 21170231 Manufacturer: Metav IndustryLine Numbers Diameter: 5.46 mm Length: 50 mm Tolerance: ±0.001 mm Weight: 0.012 kg Special features Workshop version Material: Special steel Supplied in protective case FAQ What level of precision does this gauge pin provide? The M323.546 precision gauge pin from Metav IndustryLine offers a tolerance of ±0.001 mm, permitting inspections at the micrometre level suitable for fine mechanical and precision assembly tasks. Is the pin suitable for small‑component plug‑fit checks? Yes; the 5.46 mm diameter and 50 mm length make the inspection pin well suited to plug‑fit and end‑dimension checks on small components where access is limited. How is the gauge pin delivered for safe handling? The gauge pin is supplied in a protective case to facilitate transport and to protect the pin from contamination and handling damage between uses. What material is used for the M323.546 gauge pin? The inspection pin is manufactured from special steel, chosen for dimensional stability and suitability for workshop use. Can this pin be used for laboratory calibration comparisons? The M323.546 can serve as a reference for comparative checks and final inspections in metrology benches and controlled workshop environments. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
5.47mm Gauge Pin, ±0.001mm, 50mm Length, Workshop Version - Metav IndustryLine
Take advantage of workshop‑grade construction, a 5.47 mm diameter held to ±0.001 mm tolerance and a 50 mm length for consistent end‑measurement results; order the Test pin M323.547 directly via Metav Werkzeuge or ask our consultants if needed. Test pin M323.547 — precision gauge pin, 5.47 mm diameter, ±0.001 mm tolerance (Metav IndustryLine) Test pin M323.547 is a workshop‑grade precision gauge pin designed for end‑measurement and quality control tasks in inspection and production environments. Workshop‑grade construction and finish Diameter held to ±0.001 mm tolerance Single‑piece precision pin, 50 mm length Manufactured from special steel for wear resistance Reliable accuracy that reduces rework The gauge pin delivers a ±0.001 mm specification that supports repeatable end‑measurement checks and tight fit verifications. With a nominal 5.47 mm diameter and a 50 mm shank, the component is suited to routine dimensional inspections where minute deviations matter. The tight tolerance reduces the risk of false rejects and minimises downstream rework by providing a stable reference for go/no‑go assessments and calibration checks. Built for workshop durability and frequent handling Constructed from special steel and offered in a workshop‑grade execution, the pin resists wear in daily use while maintaining geometric integrity. The 50 mm length balances reach with rigidity, making handling straightforward and measurements consistent across repeated cycles. Robust material choice and finishing ensure long service life under typical shopfloor conditions and help to preserve the pin’s measuring surface during handling and storage. Easy integration into inspection routines The single‑pin format simplifies inventory control and inspection planning: the component functions as a reference plug in manual gauges, fixtures and comparative checks. Traceable identifiers such as the SKU and GTIN support part management and document control within quality systems, while the compact form factor enables quick exchange in jigs or test rigs — reducing downtime during measurement tasks. Practical benefits for production control Using a precision reference pin with defined tolerance facilitates faster decision‑making at inspection stations. The consistent geometry enhances repeatability of fit tests and assembly checks, improving throughput where frequent dimensional verifications are required. This pragmatic approach to precision translates into measurable efficiency gains across inspection steps without requiring complex measurement equipment. Specification clarity and traceability Clear technical identifiers and basic dimensions simplify procurement and documentation: known diameter, length and tolerance mean the pin can be specified directly in inspection plans and drawings. The robust specification supports consistent quality control procedures and helps ensure compatibility with existing gauges and fixtures used in production or metrology labs. For consistent end‑measurement performance choose the Metav IndustryLine Test pin M323.547 and contact Metav Werkzeuge in Emmerich for delivery details and procurement support: info@metav-werkzeuge.com or +49 2822 7131930 Technical data Article number: M323.547 GTIN: 4061905058905 Manufacturer: Metav IndustryLine Facts Diameter: 5.47 mm Length: 50 mm Tolerance / Accuracy: ±0.001 mm Weight: 0.012 kg Special features Material: Special steel Format: Single test pin Intended use: End‑measure checks and fit verification FAQ What is the declared tolerance of this gauge pin? The Test pin M323.547 is specified with a tolerance of ±0.001 mm, suitable for precise end‑measurement tasks. Can this pin be used in usual workshop jigs and fixtures? Yes, the single‑piece, 50 mm length and 5.47 mm diameter make the pin compatible with common jigs, fixtures and manual gauge setups. What material is the pin made from and why does it matter? The pin is manufactured from special steel; this material offers improved wear resistance and maintains geometry under frequent handling. How is the part identified for procurement and traceability? Use the article number M323.547 and GTIN 4061905058905 to ensure correct ordering and documentation in quality records. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
5.48mm Gauge Pin, ±0.001mm, Length 50mm, Workshop Version, Special Steel, Packed in Case - Metav IndustryLine
Take advantage of the combination of ±0.001 mm repeatability, robust special‑steel construction and a compact 50 mm length for reliable end‑dimension checks; order the Test Pin M323.548 directly via Metav Werkzeuge or consult our specialists for application support. Test Pin M323.548 — Single precision test pin, Ø 5.48 mm, ±0.001 mm (Metav IndustryLine) The Test Pin M323.548 is a workshop‑grade precision measuring pin designed for end‑dimension verification and fixture checking in inspection and production environments. Workshop‑grade precision design Diameter 5.48 mm with ±0.001 mm accuracy Solid special‑steel construction Supplied in protective transport case Precision where tight tolerances decide produce quality The measuring probe offers ±0.001 mm nominal accuracy on a Ø 5.48 mm gauge, delivering the fine repeatability required for end‑dimension control and high‑precision jig checks. Such tight tolerance reduces measurement uncertainty in pass/fail decisions and supports consistent assembly quality. The short, rigid form factor and the 50 mm overall length make this probe particularly suited to small‑format gauges and fixture interfaces where minimal deflection is essential for reproducible results. Robust construction built for everyday workshop use Manufactured from special steel, the probe combines surface hardness and dimensional stability with a compact mass of 0.012 kg, minimising inertia during handling and mounting. The workshop execution emphasises durability under frequent use: the material choice and finish reduce wear on contact faces and preserve nominal dimensions over long service intervals. This construction supports reliable tactile measurements and prolonged service life in production and toolroom environments. Simple integration into inspection fixtures and gauges The single‑probe design allows straightforward incorporation into plug gauges, depth checks and go/no‑go fixtures. As a direct‑measuring element for end dimensions, the probe serves as a precision reference in comparative tests and calibration benches. The controlled diameter and consistent seating make it compatible with standard fixture bores and hardened contact surfaces, enabling repeatable positioning and fast inspection cycles without complex alignment procedures. Practical handling and secure delivery for immediate use With a 50 mm length and a compact diameter, the probe is easy to handle during installation and exchange; its low weight reduces strain during repetitive tasks. Delivery includes a protective transport case to prevent damage in transit and storage, ensuring the gauge arrives ready for immediate use. The compact packaging supports safe workshop logistics and reduces the risk of unintentional surface damage before installation. For reliable short‑range measurement elements from Metav IndustryLine, contact Metav Werkzeuge for order placement and application advice — eMail info@metav-werkzeuge.com or call +49 2822 7131930 to discuss suitability for specific fixtures and inspections Technical Data Article number: M323.548 SKU: M323.548 GTIN: 4061905059865 Manufacturer: Metav IndustryLine Material: Special steel Version: Workshop execution Facts Diameter: 5.48 mm Tolerance: ±0.001 mm Length: 50 mm Weight: 0.012 kg Special features Supplied in protective transport case Single probe for end‑dimension checking Workshop‑grade design for frequent use FAQ What is the stated dimensional accuracy of this test pin? The Test Pin M323.548 is specified with a tolerance of ±0.001 mm, suitable for fine end‑dimension verification and precision fixture use. Which material is used and how does it affect durability? Constructed from special steel, the probe provides enhanced surface resistance and dimensional stability, promoting long service life under workshop conditions. Is the probe suitable for use in standard plug gauges and fixtures? Yes, the compact diameter and consistent seating geometry make the probe appropriate for integration in plug gauges, go/no‑go fixtures and comparative inspection setups. How is the item delivered to ensure safe handling? The probe is supplied in a protective transport case to avoid transit damage and to keep the contact face secure until installation. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
5.49mm Gauge Pin Length 50 mm ±0.001 mm Workshop Version - Metav IndustryLine
Take advantage of the combination of micrometre-level accuracy, compact design and robust workshop construction to ensure reproducible inspection results; order the gauge pin directly via Metav Werkzeuge or contact the technical consultants for application advice. Metav IndustryLine Gauge Pin M323.549 — Ø 5.49 mm, ±0.001 mm, Length 50 mm A Metav IndustryLine gauge pin M323.549 designed for precision end‑measure checks and tight‑tolerance inspection tasks in workshop and production environments. Micrometre accuracy ±0.001 mm Workshop version for robust handling Solid special steel construction Single precision gauge pin Accuracy that secures measurement confidence The core advantage of this gauge pin is its ±0.001 mm tolerance, which corresponds to a one‑micrometre level of accuracy and supports high‑precision acceptance tests and go/no‑go inspections. Such a tight specification reduces measurement uncertainty during critical checks and enables repeatable, documented results when used as a reference or transfer standard. The compact diameter combined with a length of 50 mm keeps thermal mass low and shortens stabilisation time, benefiting throughput in serial inspection tasks. Robust construction for dependable workshop use Manufactured from special steel, the pin is finished to a high standard to resist wear in frequent use while preserving the measured geometry. The workshop version designation indicates an emphasis on mechanical resilience and handling ergonomics rather than delicate laboratory packaging, which suits bench inspection, fixture set‑up and routine maintenance tasks in metalworking and toolrooms. The modest mass supports rapid placement and positioning without adding measurement artefacts from excessive weight. Practical performance and integration in inspection routines As a single precision gauge pin, this component is well suited for bore checking, gauge‑block interfaces and position referencing in fixtures. The Ø 5.49 mm size fits small bores and tight seats where larger pins would be unsuitable. When used together with calibrated masters or inside precision jigs, the pin contributes to a reproducible inspection chain; traceability can be achieved by recording serial and batch details during quality control procedures. The design supports efficient exchange in modular fixtures and quick verification cycles on the shop floor. Contact Metav Werkzeuge today to arrange supply of the Metav IndustryLine M323.549 gauge pin and to discuss suitable inspection workflows with our specialists Technical Data Article number: M323.549 Manufacturer: Metav IndustryLine GTIN: 4061905059872 Core data Diameter: 5.49 mm Tolerance: ±0.001 mm Length: 50 mm Weight: 0.012 kg Special features Workshop version Material: Special steel Single precision gauge pin High‑precision finish FAQ What is the declared tolerance of this gauge pin? The declared tolerance is ±0.001 mm for the Metav IndustryLine gauge pin M323.549, providing micrometre‑class accuracy for tight tolerance inspections. Which materials is the pin made from and why does that matter? The pin is made from special steel, chosen for wear resistance and dimensional stability; Metav IndustryLine specified this material to keep surface integrity and longevity under frequent contact use. For which typical tasks is this gauge pin intended? Typical tasks include small‑bore checking, fixture referencing and end‑measure verification where a Ø 5.49 mm reference is required and micrometre accuracy is essential. Is this product suitable for production‑line interchangeability checks? Yes, the M323.549 is suitable for production interchangeability and rapid go/no‑go checks thanks to its tight tolerance and compact length, which speed up handling and repeatability. Does the specification indicate any special surface finish or treatment? The listing states a high‑precision finish consistent with workshop use; detailed surface treatments are not specified beyond the material and workshop designation Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
5.4mm Gauge Pin, Single, ±0.001mm, 50mm Length, Workshop Version - Metav IndustryLine
Take advantage of micrometre-level accuracy and compact handling for reliable end‑measurements; the combination of ±0.001 mm tolerance and a Ø 5.40 mm, 50 mm profile supports tight fit checks and fixture set‑up. Order directly via Metav Werkzeuge or consult our specialists for application advice. Gauge pin M323.540 — Metav IndustryLine, Ø 5.40 mm, ±0.001 mm, 50 mm The gauge pin M323.540 is a single test pin designed for precision end‑measurements and fixture alignment in workshop environments. Workshop version, robust construction Tolerance ±0.001 mm for micrometre accuracy Diameter Ø 5.40 mm, precise fit Length 50 mm for compact handling Precision that reduces uncertainty The instrument delivers ±0.001 mm repeatability, enabling measurements at the micrometre level for critical checks. Built as a single test pin, it is intended where minimal clearance and exact seating are required; the fine tolerance reduces ambiguity in go/no‑go verifications and ensures consistent results when used for end‑mass checks or as a reference mandrel. This focus on measurable accuracy supports efficient quality control processes and simplifies pass/fail decisions on the shop floor. Designed for hard use in workshop routines Manufactured from special steel, the component combines wear resistance with a compact geometry that eases handling during repeated operations. The workshop version designation indicates practical design choices such as firm seating and durable surface finish, which extend service life under frequent insertion and removal. At a 50 mm length the pin is long enough to stabilise the measured part yet short enough for quick, single‑handed positioning in fixtures and measuring jigs. Versatile applications across small precision tasks The pin is suitable for end‑dimension inspection, fixture set‑up, pin gauges in alignment procedures and verification of bores and seats where a precise diameter is required. Its Ø 5.40 mm diameter provides a defined reference for fit testing and for establishing datum relationships in assemblies. Where interchangeability and exact fits are necessary, this component acts as a reliable mechanical reference that complements dial indicators, micrometres and bench comparators. Procurement confidence and workshop integration The compact mass (approx. 0.012 kg) and single‑piece supply make the pin straightforward to stock and deploy. Supplied as an individual test pin, it integrates with existing inspection workflows without the need for special adapters. Metav IndustryLine’s product range is positioned to bridge affordability and industrial‑grade quality, offering dependable parts for routine metrology tasks and reducing the need for repeated rework due to measurement uncertainty. Contact Metav Werkzeuge for tailored advice on using the M323.540 gauge pin in measurement routines and to arrange procurement from stock at Emmerich Technical Data Article number: M323.540 SKU: M323.540 GTIN: 4061905057953 Manufacturer: Metav IndustryLine Facts Diameter: 5.40 mm Length: 50 mm Tolerance: ±0.001 mm Weight: 0.012 kg ECLASS: 21170231 Special features Material: special steel Workshop version Single test pin Category: Messstifte FAQ What tolerance does this gauge pin offer? The gauge pin M323.540 is specified with a tolerance of ±0.001 mm, providing micrometre‑level accuracy for precise fit and end‑dimension checks. Which material is used for the pin? The component is made from special steel, selected for wear resistance and durability in repeated inspection and fixture applications. For which tasks is this test pin suitable? Typical uses include end‑measurement verifications, fixture and jig alignment, go/no‑go fit testing and verification of bore seats where an exact diameter reference is required. What are the exact dimensions and mass of the pin? Diameter is 5.40 mm, length 50 mm and mass approximately 0.012 kg for the M323.540 gauge pin from Metav IndustryLine. Is this pin supplied as a single unit or in sets? The product is supplied as a single test pin (individual item), intended for direct integration into inspection and fixture procedures. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
Fast, tactile checks where electronics are impractical
Gauges and test pins provide unequivocal go/no-go results for threads, bores, gaps and radii without relying on electronics. The range covers plug gauges and ring gauges for internal and external threads, feeler gauges and precision feeler strips for micro‑gap assessment, plus probe pins and measuring pins for tactile diameter and pitch checks.
How these tools work in the production environment
Mechanical gauges operate as direct reference standards: a plug gauge or ring gauge verifies conformity to thread profiles and mating ability, while limit gauges separate accept from reject in a single step. Test pins are used to tactilely measure small bore diameters, centre‑to‑centre distances and radii. Manufactured from hardened gauge steel or ceramic and often precision lapped, these instruments deliver immediate physical results that are ideal for incoming inspection, machine‑side checks and final control.
Measurable benefits that affect production performance
- Reduced scrap and rework through rapid, unambiguous pass/fail assessment.
- Increased repeatability thanks to very low measurement uncertainty and fine lapping.
- Lower downtime: quick checks at the machine save cycle time and reduce setup periods.
- Durable construction with high wear resistance from specialised, low‑distortion alloys.
- Versatile delivery formats: individual gauges, organised sets in wooden cases or metre‑length feeler rolls compliant with DIN 2269.
Why Metav is the practical choice for precision supplies
Metav combines decades of expertise with a broad warehouse and quality filtering from Emmerich. As a precision partner for industry, craft and trade, Metav supplies a comprehensive selection of gauges and test pins alongside complementary tools such as precision calipers and setting rings. With over 48,000 customers and a catalogue exceeding 250,000 items, Metav is positioned to supply reliably, reduce vendor complexity and support traceable quality control to national standards.
Summary
Gauges and test pins are indispensable for dependable, repeatable quality assurance where tactile, mechanical verification is preferred. Choose these plug gauges, ring gauges, feeler strips and probe pins when immediate, robust measurement decisions are required on the shop floor.
FAQ
What materials are gauges and test pins typically made from?
Gauges and test pins are usually manufactured from hardened gauge steel for durability and wear resistance; ceramic variants are available where thermal stability and minimal wear are critical.
How do thread gauges ensure mating capability?
Thread plug gauges and ring gauges check flank diameters and thread form against standards, providing a clear go/no‑go verdict that confirms pairability with mating parts.
Which tolerance class should I choose for probe pins and gauge sets?
Select tolerance classes aligned with your inspection requirements; for high‑precision tasks, sets produced to DIN 2269 or equivalent tolerance classes ensure micrometre‑level control and repeatability.
Can feeler gauges measure contact gaps in valve and engine work reliably?
Yes. Feeler gauges and precision feeler strips, supplied either as a fan or metre‑length rolls, allow accurate assessment of valve clearances and contact gaps down to micrometre increments.
How do limit gauges speed up in‑process inspection?
Limit gauges separate good from bad in a single, tactile operation, enabling rapid go/no‑go checks at the machine and reducing both inspection time and the likelihood of human interpretation errors.
Fragen zu diesen Produkten??
Mit mehr als 30 Jahren Erfahrung beraten wir Sie gerne persönlich.
Tel.: +49 2822 7131930
Mail: info@metav-werkzeuge.com