Precision gauge blocks and plug gauges for reliable dimensional control
Mechanical gauge blocks and plug gauges are essential for tactile verification of threads, bores and gap dimensions, providing fast, unambiguous go/no-go results that enhance process reliability and reduce scrap. Designed for industrial metalworking and toolmaking, these precision tools support incoming inspection and final quality checks by delivering traceable measurements in applications such as thread inspection, bore diameter testing and spacing checks. Manufactured from specially hardened, low-distortion alloys and fine-lapped for minimal measurement uncertainty, the range includes thread plug gauges, precision plug gauges and calibration gauge blocks to ensure long-term repeatability and wear resistance.
5.73mm Gauge Pin ±0.001mm Length 50mm Workshop Version - Metav IndustryLine
Combine micrometre‑level accuracy with a compact, workshop‑ready design for dependable end‑measurements; the 5.73 mm diameter at ±0.001 mm tolerance and 50 mm length deliver consistent reference fits. Order directly via Metav Werkzeuge or consult our specialists for application advice. Gauge pin M323.573 — 5.73 mm, ±0.001 mm, 50 mm length (Metav IndustryLine) A gauge pin designed for precise end‑measurements and reference fitting in workshop metrology, available in a robust workshop execution. Diameter 5.73 mm with ±0.001 mm tolerance 50 mm length in workshop execution Made from special steel for durability Supplied in protective transport case Micrometre precision for repeatable end‑measurements The core advantage of this tool is its extreme accuracy: a tolerance of ±0.001 mm corresponds to 1 µm, making the pin suitable for measurement and inspection tasks where tight form and size control are required. At 5.73 mm diameter the component serves as a precise reference for bore checks, plug‑fits and end‑dimension verification. Such repeatability reduces downstream rework and supports consistent process control in production and quality‑assurance setups. Built for workshop use and safe handling Manufactured in special steel and specified as a workshop execution, the pin combines strength with a compact footprint. The 50 mm overall length provides a balance between handling convenience and sufficient engagement depth for many small to medium components. Supplied in a protective transport case, the item remains protected during storage and transit, helping to preserve the calibrated condition and surface integrity that determine reliable measurements. Practical integration into inspection routines As a small, high‑precision reference element, the pin integrates easily into bench inspection workflows, gauge assemblies and fixture checks. The compact mass and standard form factor permit rapid placement and comparison measurements, speeding up routine checks without sacrificing accuracy. Traceable identification via the SKU and GTIN supports inventory control and quality documentation, simplifying audit trails and part tracking across production stages. Proven supply and support from Metav IndustryLine Metav IndustryLine delivers this component as part of a broader offering engineered for practicality and reliability. Backed by Metav's logistics and quality filter in Emmerich, the product is supported by decades of metrology experience and a broad industrial catalogue, which helps teams standardise tools and reduce supplier complexity. The combination of precision, durable materials and workshop suitability makes this a pragmatic choice for engineering shops and quality departments seeking dependable reference pins. For precise end‑measurements choose the Metav IndustryLine gauge pin M323.573 — contact Metav Werkzeuge in Emmerich for tailored advice and fast dispatch via info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: M323.573 GTIN: 4061905058448 Manufacturer: Metav IndustryLine Facts Diameter: 5.73 mm Tolerance: ±0.001 mm Length: 50 mm Weight: 0.013 kg Special features Material: Special steel Workshop execution Supplied in transport case FAQ What level of accuracy does this gauge pin offer? The gauge pin delivers ±0.001 mm accuracy, equating to 1 µm, which makes the M323.573 suitable for high‑precision end and reference measurements in workshop metrology. For which tasks is this pin best suited? This precision pin is intended for end‑dimension checks, reference fitting and plug‑fit inspections where a 5.73 mm nominal diameter and tight tolerance are required. What material is the pin made from and why does it matter? Constructed from special steel, the pin combines wear resistance with dimensional stability, ensuring sustained measurement reliability under normal workshop conditions. Is the item delivered ready for use and how is it protected? The product is supplied in a protective transport case, which keeps the surface and dimensions secure during storage and transport, preserving measurement quality. How can the product be identified and ordered? The item is listed under SKU M323.573 and GTIN 4061905058448; these identifiers facilitate ordering and stock control for the Metav IndustryLine gauge pin. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
5.74mm Gauge Pin ±0.001mm Length 50mm Workshop Version - Metav IndustryLine
High-precision Ø 5.74 mm gauge pin with a tolerance of ±0.001 mm and a 50 mm working length ensures dependable end‑measurement checks; the workshop version in special steel and delivery in a protective case supports repeatable results and safe transport. Order the gauge pin directly via Metav Werkzeuge or consult our specialists for application advice. Gauge pin M323.574 – gauge pin, Ø 5.74 mm, ±0.001 mm (Metav IndustryLine) The gauge pin M323.574 is a workshop‑grade, single test pin designed for precise dimensional verification and end‑measurement applications in production and quality control environments Workshop version for robust use Diameter 5.74 mm with ±0.001 mm accuracy Length 50 mm in special steel Delivered in protective case Precision that secures measurement decisions Manufactured for tasks where tolerances are decisive, this test pin offers ±0.001 mm accuracy across its nominal 5.74 mm diameter. Such precision reduces downstream rework by providing a clear, objective reference when verifying bores, gauge blocks or finished end‑masses. The fine tolerance class makes the pin suitable for use in calibration benches and fixture checks where measurement uncertainty must be minimised. The compact geometry and tight specification allow integration into existing inspection jigs without complex adaptation, supporting faster throughput in series inspection while maintaining documented traceability. Built to withstand workshop conditions Designed as a workshop version, the pin combines a practical length of 50 mm with a hard‑wearing special steel. The material choice balances surface stability and corrosion resistance, ensuring consistent contact geometry over many inspection cycles. Delivered as a single item in a protective case, the pin is ready for safe storage and transport between workstations or to the inspection lab. Robustness in the component reduces the need for frequent replacement and supports reliable measurement routines under everyday shopfloor handling, contributing to lower operational disruption and longer service life. Streamlined use in inspection workflows As a single test instrument, the pin is straightforward to implement in go/no‑go checks, plug gauge arrangements and comparative setups. The slim profile and low mass make the item easy to position for quick go‑checks or when used as a reference in gauge assemblies. Laboratory technicians and production inspectors benefit from the repeatability granted by the component’s geometry and finish, enabling consistent results across shifts. Where documentation is required, the clearly specified tolerance and material data simplify reporting and quality records, supporting supplier audits and internal process control. For precise end‑measurement and dependable shopfloor inspection, contact Metav Werkzeuge to order the Metav IndustryLine gauge pin M323.574 or request tailored application guidance from our advisors. Technical data Article number: M323.574 GTIN: 4061905059407 Label: Prüfstift, einzeln, 5,74mm, +/- 0.001 mm Länge 50 mm Facts Diameter: 5.74 mm Accuracy/tolerance: ±0.001 mm Length: 50 mm Weight: 0.013 kg Special features Material: Special steel Workshop version Single item delivery Delivered in protective case Intended for end‑measurement and dimensional verification FAQ Is the gauge pin supplied ready for immediate inspection use? The gauge pin M323.574 is delivered as a single workshop unit in a protective case and can be used immediately for dimensional checks. What tolerance class does this test pin meet? This test pin provides an accuracy of ±0.001 mm, suitable for high‑precision verification and fine tolerance control. Can the pin be used for bore verification and plug gauge tasks? Yes, the Ø 5.74 mm pin is suitable for plug gauge arrangements and quick bore checks as part of standard inspection routines. What material is the pin made from and how does that affect longevity? Constructed from special steel, the pin offers durable contact surfaces and resistance to wear, supporting long service life under normal workshop conditions. Is the item supplied individually or as part of a set? The product is supplied as a single test pin (single item delivery), packaged in a protective case for transport and storage. Metav IndustryLine: Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
5.75mm Test Pin, Single, ±0.001mm, Length 50mm, Workshop Version, Special Steel - Metav IndustryLine
Take advantage of workshop‑grade robustness combined with micrometre‑class accuracy: the pin’s ±0.001 mm tolerance and 5.75 mm diameter ensure reliable end‑size inspection, while the 50 mm length and protective transport case support safe storage and handling. Order directly via Metav Werkzeuge or consult our technical team for specification advice. Test pin M323.575 — single gauge pin, 5.75 mm, ±0.001 mm The Test pin M323.575 is a workshop‑grade gauge pin for precise end‑size checks and fixture alignment in metalworking and toolmaking environments. Workshop version for rugged use Diameter 5.75 mm with ±0.001 mm tolerance Length 50 mm for fixture and gauge applications Supplied in protective transport case Precision where it counts in production High‑accuracy pin gauges are a simple but decisive element for consistent quality control. With a tolerance of ±0.001 mm, this gauge pin delivers micrometre‑class repeatability that reduces false rejects and limits rework time. The tight specification is particularly beneficial for end‑size verification and plug gauges used during setup, where consistent diameter control shortens inspection cycles and increases throughput. The result is fewer production holds and a more predictable quality flow. Robust design tailored to workshop routines Constructed from special steel, this workshop‑grade pin combines surface stability with resistance to everyday handling. At 50 mm overall length and a mass of approximately 0.013 kg, the component is easy to manipulate in fixtures and assembly benches yet stiff enough for reliable seating in bores and gauges. Delivery in a protective transport case keeps the measuring surface clean and prevents dings during storage or transit, so the pin remains ready for immediate use when called upon at the workbench. Practical gains for tooling and inspection Integrating a precision gauge pin into inspection routines simplifies go/no‑go assessments and fixture adjustments. The compact geometry makes the pin suitable for tight‑tolerance bores and alignment jigs, supporting fast comparative measurements and reducing set‑up time. As an individual measuring item, it complements gauge sets or acts as a replacement part in maintenance stocks, contributing to lower downtime and consistent production quality. The clear specification and single‑piece supply suit both small workshops and larger production lines seeking straightforward, measurable improvements. For workshop‑ready precision from Metav IndustryLine, request the M323.575 gauge pin via Metav Werkzeuge or contact our Emmerich team for tailored advice and supply options: info@metav-werkzeuge.com Technical data SKU: M323.575 GTIN: 4061905059414 Diameter: 5.75 mm Length: 50 mm Tolerance: ±0.001 mm Material: Special steel Weight: 0.013 kg Delivered in protective transport case Numbers / Core technical data Diameter: 5.75 mm Length: 50 mm Tolerance: ±0.001 mm Weight: 0.013 kg GTIN: 4061905059414 Special features / Versions Workshop version Single test pin Protective transport case for delivery Intended use: end‑size inspection and fixture alignment FAQ What tolerance can be expected from this gauge pin? The M323.575 gauge pin is specified with a ±0.001 mm tolerance, providing micrometre‑class accuracy suitable for end‑size verification. Which material is used for the pin? The pin is made from special steel, chosen for dimensional stability and robustness in workshop use. Is the pin supplied ready for use and protected during transport? Yes, the item is supplied as a single test pin and shipped in a protective transport case to preserve the measuring surface. Can this pin be used for fixture alignment and gauge sets? The compact 5.75 mm diameter and 50 mm length make the M323.575 suitable for fixture alignment, plug checks and as a replacement part in gauge sets. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
5.76mm Gauge Pin Single ±0.001mm Length 50mm Workshop Finish - Metav IndustryLine
High-precision end-dimension checks become straightforward with a 5.76 mm gauge pin that delivers ±0.001 mm repeatability over a 50 mm shaft; combine this dimensional accuracy with workshop-grade construction for dependable verification in production and inspection tasks. Order the gauge pin directly via Metav Werkzeuge or ask our consultants for application-specific guidance. M323.576 gauge pin — 5.76 mm, ±0.001 mm accuracy, 50 mm length M323.576 is a precision gauge pin designed for end‑dimension and positional verification in workshop and inspection environments. ±0.001 mm tolerance for high-precision checks 5.76 mm diameter matched to end‑dimension control 50 mm shaft for accessible insertion depth Special steel construction for workshop execution Consistent micron-level verification for production control The gauge pin provides a reliable reference for final dimension checks, with a stated ±0.001 mm accuracy that supports high‑precision tasks where repeatability matters. The small diameter makes the component suitable for tight tolerances and fine fits, while the specified tolerance establishes a quantifiable basis for pass/fail decisions in inspection routines. This level of precision reduces uncertainty in critical measurements and helps maintain product quality across serial production. Robust design tailored to workshop routines Manufactured in special steel and labelled as a workshop execution, the probe is built for frequent handling and insertion cycles typical in daily measurement tasks. The 50 mm shaft length gives enough engagement for many end‑dimension and positional checks without compromising handling comfort, and the single‑piece format simplifies stockkeeping and replacement. The overall design balances durability with the fine detail required for accurate gauging, making it practical for both bench inspection and in-process checks. Easy integration into quality workflows As a compact test pin, the component slots into existing gauge sets, fixtures or test jigs and supports straightforward comparison measurements and functional go/no‑go routines. The clear specification of diameter, length and tolerance enables rapid documentation in inspection plans and traceability records. Where consistency of result is essential, the defined metrology parameters allow planners to model measurement uncertainty and to align the probe with current quality standards. Contact Metav Werkzeuge for tailored advice on integrating the Metav IndustryLine gauge pin M323.576 into inspection routines and to secure reliable supply from Emmerich. Technical data Article number: M323.576 GTIN: 4061905059421 Manufacturer: Metav IndustryLine Facts Diameter: 5.76 mm Length: 50 mm Tolerance/accuracy: ±0.001 mm Weight: 0.013 kg Special features Material: special steel Workshop execution Single-piece probe format FAQ What measurement accuracy does the gauge pin offer? The gauge pin delivers an accuracy of ±0.001 mm, making the M323.576 suitable for high-precision end‑dimension verification. Is the probe suitable for routine workshop use? Yes, the workshop execution and special steel construction of the M323.576 ensure it withstands regular handling and insertion cycles typical in inspection stations. How deep can the pin be inserted for checks? The 50 mm shaft provides the insertion depth required for most end‑dimension and positional checks while maintaining shaft stability. Can the pin be used within existing gauge sets or fixtures? The compact, single-piece format of this gauge pin allows straightforward integration into standard gauge sets and test jigs for comparative or go/no‑go measurements. What information is available for traceability? Specification details such as diameter (5.76 mm), length (50 mm) and tolerance (±0.001 mm) are provided for inclusion in inspection plans and traceability documentation. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
5.77mm Gauge Pin, ±0.001mm Accuracy, 50mm Length, Workshop Version, Special Steel - Metav IndustryLine
Combining micron-level accuracy, a compact Micro-range format and a workshop-ready design ensures reproducible inspection results with minimal rework; ideal for precision fits and quality checks in small assemblies. Order the gauge pin directly via Metav Werkzeuge or ask our consultants if needed. Gauge pin M323.577 (single test pin, 5.77 mm, ±0.001 mm) — Metav IndustryLine Gauge pin M323.577 is a single test pin for high-precision dimensional inspection in fine mechanical and workshop environments Micron-level tolerance ±0.001 mm Precision ground 5.77 mm diameter Workshop-ready with transport case Reproducible accuracy for small diameters The gauge pin delivers a measured diameter of 5.77 mm with an exceptional ±0.001 mm tolerance, making it suitable where tight fits and minimal clearance are critical. Thanks to its fine tolerance, the pin reduces the need for iterative adjustments and rework during assembly or inspection processes, improving throughput in small-part production. The compact dimensions and precision finish facilitate use in gauging fixtures and comparative checks where consistent contact and repeatability are required. Built for daily workshop use and longevity Manufactured from special steel and specified as a workshop version, the test pin resists everyday handling and retains dimensional stability under regular inspection cycles. The hardened and ground surface ensures reliable contact geometry, which maintains measurement integrity over time and reduces the frequency of replacements. This robustness supports continuous production checks and lowers overall maintenance effort by providing a stable reference for go/no-go tests and fit verifications. Practical handling and ready-to-store organisation With a length of 50 mm and a lightweight construction (approximately 0.013 kg), the pin is easy to position in jigs and fixtures, while remaining rigid enough for precise insertion. Delivery includes a transport case suitable for workshop use, which protects the pin during transit and storage and simplifies inventory management. The compact format is particularly advantageous in confined measurement setups and for technicians who require a portable, reliably protected reference gauge. Streamlined inspection workflows and traceability Designed as a straightforward inspection tool, the pin integrates smoothly into manual and semi-automated checking routines. Clear identifiers such as M323.577 and GTIN: 4061905059438 enable rapid ordering and stock control in procurement systems. The combination of a micro-range format with micron tolerance supports quality assurance steps that prevent downstream assembly issues, helping to reduce scrap and ensure component interchangeability across batches. Contact Metav Werkzeuge for availability and tailored advice on integrating this Metav IndustryLine gauge pin into existing inspection routines Technical data Article number: M323.577 GTIN: 4061905059438 Category: Gauge pins Facts Diameter: 5.77 mm Tolerance: ±0.001 mm Length: 50 mm Weight: 0.013 kg Special features Material: special steel Workshop version Delivery: in plastic or wooden transport case SKU: M323.577 FAQ What applications is this gauge pin suited for? This gauge pin is intended for fine mechanical inspection and small-part checking; the Metav IndustryLine gauge pin M323.577 is especially useful for precision fits and dimensional verification in miniature assemblies. Does the pin come with a certificate of calibration? No calibration certificate is specified for this item; the Metav IndustryLine product M323.577 is supplied as a precision ground test pin for workshop use without an ISO 17025 certificate unless specifically ordered. How should the pin be stored between uses? Store the test pin in its supplied transport case to protect the ground surface and ensure long-term dimensional stability; the case included with M323.577 simplifies organised storage. Can the gauge pin be used in gauging fixtures? Yes, the compact length and rigid design make the pin suitable for gauging fixtures and manual go/no-go checks as part of standard inspection equipment. How can M323.577 be ordered or referenced? Refer to article number M323.577 or GTIN 4061905059438 when ordering to ensure exact identification of the Metav IndustryLine gauge pin. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
5.78mm Gauge Pin, ±0.001mm Accuracy, 50mm Length, Workshop Version, Special Steel - Metav IndustryLine
The combination of ±0.001 mm tolerance, a precise 5.78 mm diameter and a robust 50 mm length delivers reproducible inspection results and reduced scrap rates on the shop floor; choose this gauge pin for dependable end‑measure checks and controlled interchangeability. Order the gauge pin directly via Metav Werkzeuge or consult our specialists for application support. Gauge pin, 5.78 mm, ±0.001 mm, 50 mm — Metav IndustryLine A gauge pin designed for precision end‑measure inspection in workshop and production environments. High-precision tolerance ±0.001 mm Diameter 5.78 mm exact ground Length 50 mm for component checks Workshop design in special steel Consistent dimensional control to speed inspection A finely ground gauge pin with a diameter of 5.78 mm and a rated tolerance of ±0.001 mm provides a reliable reference for go/no‑go checks and tight fits. The very small tolerance reduces measurement uncertainty, which in turn lowers the risk of rejected parts and rework. Using a dedicated inspection mandrel instead of improvised gauges shortens throughput times in quality control, as one defined reference replaces repeated comparative methods while improving traceability during series testing. Material and manufacturing benefit accuracy and durability Manufactured from special steel, the pin combines surface hardness and corrosion resistance suited to regular workshop use. The precision grinding process creates a consistent cylindrical profile that maintains contact geometry during measurement, supporting repeatable results. The robust material choice and workshop specification mean the pin resists wear from frequent insertion cycles, so calibration intervals are extended and tool life is increased — an economic benefit for production and maintenance planning. Practical form factor for everyday checks With a 50 mm overall length, the inspection pin reaches typical bore depths while remaining easy to handle and position in fixtures. The compact but deliberate length ensures stable seating during end‑measure inspections and reduces bending or misalignment compared with overly long probes. Designed for straightforward use in assembly, jigs and test benches, the pin integrates seamlessly into existing workflows and supports rapid in‑process verification without special adapters. Traceability, identification and workshop readiness Each unit is supplied as a single, individually identified gauge pin, complete with a unique article reference and GTIN for inventory and quality records. The product’s workshop classification highlights suitability for everyday production tasks rather than delicate laboratory work, offering a balance between precision and robustness. For production environments seeking standardised inspection tools, this pin provides an accessible and durable solution that aligns with industrial quality processes. For application advice or to secure a steady supply of Metav IndustryLine inspection tools, contact Metav Werkzeuge in Emmerich—our team will advise on integration and deliverability to match production requirements. Technical Data Article number: M323.578 GTIN: 4061905059445 Manufacturer: Metav IndustryLine Facts Diameter: 5.78 mm Tolerance / Accuracy: ±0.001 mm Length: 50 mm Weight: 0.013 kg Special features Workshop version Material: special steel Delivered as single gauge pin SKU: M323.578 FAQ What measurement accuracy can be expected from this gauge pin? The gauge pin offers a rated accuracy of ±0.001 mm, making it suitable for high‑precision end‑measure inspections where tight tolerances are required. Is the material suited for regular workshop use and frequent handling? Yes; the pin is made from special steel and specified as a workshop version, combining durability with the surface properties needed for repeated insertion and removal. Can this pin be used for bore checks and component end‑measure inspections? The 5.78 mm diameter and 50 mm length make this pin ideal for bore checks and end‑measure verification of through‑holes and seating features in typical production parts. How is the product identified for inventory and traceability? The item is supplied with an article number (M323.578) and GTIN (4061905059445) for simple tracking in quality and inventory systems. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
5.79mm Test Pin ±0.001mm Length 50mm Workshop Finish - Metav IndustryLine
Take advantage of the combination of industrial accuracy, compact dimensions and robust workshop design to streamline end‑measure inspections; the precise ±0.001 mm tolerance on a 5.79 mm diameter pin and a 50 mm length supports consistent pass/fail decisions on the shop floor. Order the item directly via Metav Werkzeuge or consult the team for application advice. Gauge pin M323.579 – 5.79 mm, ±0.001 mm, length 50 mm (Metav IndustryLine) The gauge pin M323.579 is a single precision measuring pin designed for end‑measure verification and dimensional checking in workshop and inspection environments. Precision ±0.001 mm tolerance Diameter 5.79 mm for end‑measure checks Length 50 mm for compact fixture use Workshop version made from special steel Faster, more reliable inspection decisions through tight tolerance control With a declared ±0.001 mm variation, this measuring pin reduces uncertainty in pass/fail checks and supports faster quality decisions. The narrow tolerance translates into fewer ambiguous readings during go/no‑go checks, which in turn lowers rework rates and shortens inspection cycles. By combining a fine tolerance with a defined diameter, the pin ensures repeatable contact geometry, making it suitable for routine dimensional verification where consistent results are required. Robust material and compact form for daily workshop use Manufactured from special steel, this workshop‑grade pin resists wear under frequent use while maintaining its measuring edge and surface integrity. The 50 mm length provides a compact handling profile that is easy to install in fixtures or use freehand when checking end‑measures on small to medium components. The solid construction and balanced mass support stable contact during measurement, helping to avoid bounce or misalignment that could compromise a reading. Integrates with existing checking workflows and fixtures Designed as a single measuring element for end‑measure applications, the pin fits into common gauge sets and dedicated checking fixtures to expand existing inspection capabilities. The compact design and low mass facilitate fast swapping and positioning, making it practical for repetitive quality tasks. Lightweight handling minimises operator fatigue during batch inspection and the clear nominal diameter supports traceable results within an established measurement routine. For workshop‑grade precision from Metav IndustryLine, request the M323.579 gauge pin via Metav Werkzeuge for supply and technical advice at info@metav-werkzeuge.com or by phone on +49 2822 7131930. Technical Data Article number: M323.579 GTIN: 4061905059452 Brand: Metav IndustryLine Facts Diameter: 5.79 mm Length: 50 mm Tolerance: ±0.001 mm Weight: 0.013 kg Special features Workshop execution Material: special steel Single measuring pin for end‑measure checks Intended for compact fixture and handheld use FAQ What is the primary application for this gauge pin? The gauge pin M323.579 from Metav IndustryLine is intended for end‑measure verification and dimensional checking in workshop and inspection settings. Does the pin resist wear during frequent use? Yes, the pin is made of special steel, which offers increased wear resistance appropriate for recurring shop‑floor inspection tasks. How does the ±0.001 mm tolerance affect inspection? A tight ±0.001 mm tolerance provides clearer pass/fail decisions and reduces ambiguous measurements during routine checks. Can the pin be used in existing fixtures and gauge sets? The compact 50 mm length and standardised diameter make the pin compatible with common fixture arrangements and gauge sets for end‑measure checks. Is the gauge pin supplied individually or in sets? This item is supplied as a single measuring pin (single unit), suitable for adding to bespoke gauge arrangements or replacing worn elements. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
5.7mm Gauge Pin ±0.001mm Length 50mm Workshop Version - Metav IndustryLine
This precision 5.70 mm gauge pin, with ±0.001 mm tolerance and a 50 mm length, delivers reliable inspection results and repeatable fits for small-bore components; its special steel construction suits demanding workshop use. Order the item directly via Metav Werkzeuge or request advice from our consultants for application-specific guidance. Gauge pin M323.570 – 5.70 mm diameter, ±0.001 mm tolerance by Metav IndustryLine A gauge pin M323.570 engineered for precision inspection and fixture verification in workshop and metrology environments. 5.70 mm diameter precision pin Tolerance ±0.001 mm for high accuracy Length 50 mm for deeper bores Workshop-grade special steel construction Precision that secures measurement confidence The combination of a 5.70 mm nominal diameter and ±0.001 mm tolerance makes this gauge pin a dependable reference for tight-tolerance checks. Designed to provide high accuracy in repetitive inspections, the test pin minimises uncertainty when verifying bores, pins and mating features. The narrow tolerance range supports quality assurance processes by reducing rework and ensuring parts conform to specified fits. Where repeatable results matter, a hardened, dimensionally stable reference like this plays a decisive role. Robust design for everyday workshop handling Built as a workshop version, the pin uses special steel to resist wear during frequent use. The 50 mm length reaches deeper features while remaining simple to handle and store; its compact mass supports fast alignment in gauges and fixtures. The construction balances surface hardness with corrosion resistance so the component retains dimensional integrity across standard workshop conditions. This focus on durability translates into fewer replacements and lower lifecycle costs for routine inspection tools. Practical integration into inspection workflows As a precision reference component, the pin integrates seamlessly into caliper, bore gauge and fixture checks, helping to accelerate inspection cycles without compromising accuracy. The modest weight and straight geometry make it suitable for manual and jig-based verification routines. Traceability is supported by clear identification: article number M323.570 and GTIN are provided in the technical data for inventory and quality records. For users seeking stable, workshop-capable gauges, this precision pin offers a straightforward, low-overhead way to tighten process control. Choose the Metav IndustryLine gauge pin M323.570 for dependable workshop accuracy; contact Metav Werkzeuge for tailored advice or to arrange supply via info@metav-werkzeuge.com or +49 2822 7131930 Technical data Article number: M323.570 GTIN: 4061905058417 Manufacturer: Metav IndustryLine Weight: 0.013 kg Label: Prüfstift, einzeln, 5,70mm, +/- 0.001 mm Länge 50 mm Facts Diameter: 5.70 mm Tolerance: ±0.001 mm Length: 50 mm Mass: 0.013 kg Special features Material: Special steel Version: Workshop execution Single test pin for inspection and fixture use FAQ What is the nominal diameter and tolerance of this pin? The gauge pin has a nominal diameter of 5.70 mm with a tolerance of ±0.001 mm, specified for the M323.570 precision pin from Metav IndustryLine. Can this pin be used for bore checking in fixtures? Yes, the M323.570 gauge pin is intended for fixture and bore verification; its 50 mm length is suited to checking deeper bores and aligning components. What material is the pin made from? The pin is manufactured from special steel, selected for wear resistance and dimensional stability in workshop conditions. Is the pin supplied individually or in a set? The product is supplied as a single gauge pin, article number M323.570, suitable for inventory by piece. How does this pin support quality assurance processes? With a tolerance of ±0.001 mm, the pin provides a stable reference for repeatable inspections, helping to reduce measurement uncertainty and support consistent acceptance criteria. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
5.81mm Test Pin Single ±0.001mm Length 50mm Workshop Version - Metav IndustryLine
Take advantage of the combination of ultra‑fine tolerance, compact dimensions and workshop‑grade robustness to secure reliable end‑measurement references. Order the gauging pin directly via Metav Werkzeuge or contact our consultants for application advice. M323.581 Gauging pin – Metav IndustryLine (Ø 5.81 mm, ±0.001 mm) A gauging pin designed for precise end‑dimension checks and reference tasks in workshop metrology, offering micrometre‑level reproducibility in a compact format Workshop version for robust daily use Diameter 5.81 mm with ±0.001 mm accuracy 50 mm ground length for stable reference Precision that reduces rework and inspection time The core advantage of this tool is its ±0.001 mm nominal tolerance, which corresponds to 1 µm resolution in practice and provides a dependable reference for fine fitting and go/no‑go verification. A cylindrical diameter of 5.81 mm is produced to tight limits so that the component or gauge where it is used registers minimal clearance variation. By using a dedicated gauging pin as a reference mandrel or alignment aid, measurement uncertainty is reduced and downstream rework is avoided—benefits that translate directly into shorter inspection loops and steadier production outcomes. Durable design for everyday workshop routines Manufactured from special steel in a workshop version, the pin combines surface hardness with a ground finish along the 50 mm usable length to ensure consistent contact geometry and wear resistance. The compact mass and small cross‑section make handling straightforward while the ground length provides a stable datum against which measurements or settings can be repeatedly made. Delivery in a protective transport case preserves the ground surfaces during storage and transport, helping to maintain the original tolerance over many inspection cycles. Traceability, cataloguing and practical integration Lightweight construction (approximately 0.013 kg) and single‑piece supply simplify inventory and tool‑setting logistics. The item is listed under SKU M323.581 and GTIN 4061905060335, making procurement and traceability straightforward for quality documentation. Suited to end‑dimension checks and fixture setting, this compact reference element fits into standard inspection workflows and complements other workshop gauges. Metav IndustryLine provides the logistical and quality‑assurance backbone from Emmerich, ensuring availability and a consistent supply chain for routine and scheduled measurement tasks. For specific advice on integrating the M323.581 gauging pin into inspection routines or to secure stock for production, contact Metav Werkzeuge in Emmerich by phone on +49 2822 7131930 or by email at info@metav-werkzeuge.com Technical data SKU: M323.581 GTIN: 4061905060335 Brand: Metav IndustryLine Description: Single gauging pin Ø 5.81 mm, ±0.001 mm, length 50 mm Facts Diameter: 5.81 mm Tolerance: ±0.001 mm Length: 50 mm Weight: 0.013 kg Special features Material: Special steel Workshop version Delivered in transport case Single piece supply Category: Gauge pins Application: End measurements FAQ What tolerance does this gauging pin offer? The M323.581 gauging pin from Metav IndustryLine is specified at ±0.001 mm, providing micrometre‑level reference accuracy for inspection and setting tasks. Is the pin suitable for regular workshop use? Yes — the workshop version is manufactured from special steel with a ground 50 mm length and is supplied in a transport case to protect the measuring surface during daily handling. How is the item identified for procurement and documentation? The product is listed as SKU M323.581 with GTIN 4061905060335, which supports straightforward ordering and traceability in quality records. For which measurement tasks is this pin typically used? This gauge pin is intended for end‑dimension checks, fixture alignment and as a reference mandrel in workshop inspection processes where consistent contact geometry is required. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
5.82mm Test Pin, Single, ±0.001mm Accuracy, 50mm Length, Workshop Version - Metav IndustryLine
Take advantage of the combination of workshop-ready robustness, micron-level accuracy and practical handling for consistent inspection results; order directly via Metav Werkzeuge or ask the consultants for application advice. M323.582 Test Pin (Gauge Pin) – 5.82 mm Ø, ±0.001 mm, 50 mm length | Metav IndustryLine The M323.582 is a compact test pin designed for precision end‑measure checks and gauge applications in workshop and inspection environments. Workshop-grade construction Diameter 5.82 mm, tolerance ±0.001 mm Length 50 mm for stable handling Delivered in protective transport case Accuracy that saves time and rejects The M323.582 is engineered for repeatable measurements where small deviations matter. With a diameter of 5.82 mm and a verified tolerance of ±0.001 mm, this precision pin reduces measurement uncertainty during dimensional checks and fixture set‑up. The tight tolerance corresponds to micron-level control, which often translates into fewer reworks and more reliable process decisions. As a result, inspection cycles become more predictable and quality gates are easier to enforce. Built for workshop use and straightforward handling Constructed in special steel, the test pin combines wear resistance with a compact 50 mm shank that is easy to seat in holders or gauges. The workshop-grade execution ensures robustness against daily handling, while the modest mass of 0.013 kg contributes to convenient manipulation without excess inertia. Delivery in a protective transport case preserves the measurement face during storage and transport, keeping the function ready for immediate use on the shop floor. Seamless integration into inspection routines This gauge pin fits standard plug and gauge arrangements and is suitable for end‑measure verifications, alignment of fixtures and quick go/no‑go checks where a defined diameter reference is required. The simple geometry minimises operator influence and supports consistent tactile positioning in assemblies. The combination of compact form and high repeatability makes the pin a practical component within quality control processes and assembly jigs. For workshop-ready precision from Metav IndustryLine, contact Metav Werkzeuge in Emmerich to secure the M323.582 and confirm suitability for specific inspection tasks — Metav Werkzeuge is available at info@metav-werkzeuge.com or by phone on +49 2822 7131930 Technical Data Article number: M323.582 GTIN: 4061905060342 Manufacturer: Metav IndustryLine Material: Special steel Weight: 0.013 kg Facts Diameter: 5.82 mm Length: 50 mm Tolerance: ±0.001 mm Mass: 0.013 kg Special features Workshop-grade execution Protective transport case included Precision tolerance for end-measure checks Compact form for fixture and gauge integration FAQ What are the exact dimensions and tolerance of this gauge pin? The gauge pin measures 5.82 mm in diameter with a tolerance of ±0.001 mm and a length of 50 mm, making it suitable for fine dimensional references. Which material is used for the test pin? The M323.582 is manufactured from special steel, chosen for wear resistance and stability under normal workshop conditions. Is the pin supplied in a protective container? Yes, the item is shipped in a protective transport case to reduce the risk of damage during handling and storage. For which inspection tasks is this product intended? Typical uses include end‑measure checks, fixture alignment, plug‑gauge references and rapid go/no‑go verification where a precise diameter datum is required. Is a calibration certificate included with the pin? Product data does not specify a calibration certificate. For traceable calibration options or certificates, select versions or services that explicitly list calibration details. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
5.83mm Gauge Pin, Single, ±0.001mm, 50mm Length, Workshop Version - Metav IndustryLine
Take advantage of the combination of ultra‑fine precision, robust special steel construction and protective transport packaging for reliable inspection and reference measuring in workshop environments. Order the gauge pin directly via Metav Werkzeuge or consult our advisors for batch or delivery enquiries. M323.583 Gauge pin — 5.83 mm, ±0.001 mm (Metav IndustryLine) The M323.583 gauge pin is a single inspection pin designed for end‑measure checks, reference gauging and fixture setup in workshop metrology. Precision ±0.001 mm for micrometric checks Nominal diameter 5.83 mm Length 50 mm, workshop version Supplied in transport case Accurate reference for quick pass/fail checks The M323.583 serves as a compact, high‑precision gauge pin for repetitive verification tasks. With a tolerance of ±0.001 mm, the pin provides micrometric certainty when used as a reference element in plug gauges, jigs or inspection fixtures. The small footprint and 50 mm shank length make it particularly useful where space is limited but measurement certainty must not be compromised. Measurable performance reduces rework and supports consistent production quality by turning intermittent checks into reliable, repeatable data points. Durable workshop design that handles everyday use Manufactured from special steel, this inspection pin combines hardness with corrosion resistance suited to routine workshop handling. The workshop version finish balances wear resistance and ease of cleaning, while the low mass (approx. 13 g) simplifies handling during rapid inspection cycles. Delivered in a protective transport case, the pin arrives ready for insertion into toolboxes or inspection kits—minimising the risk of damage during transit and storage and ensuring the calibrated geometry remains intact for practical use. Practical benefits for quality assurance and fixture building As a single, nominally 5.83 mm plug, the component is ideal for end‑measure verification, alignment references and setting gauges during assembly and maintenance work. The clearly defined tolerance and compact form factor support faster decision making on the shop floor, reducing downtime caused by uncertain measurements. For procurement and planning, the product is offered under the Metav IndustryLine umbrella, which emphasises accessible precision and dependable supply for industrial customers and specialist workshops. Contact Metav Werkzeuge for tailored delivery options, batch supply or advice on integrating the M323.583 gauge pin into existing inspection routines Technical Data Article number: M323.583 GTIN: 4061905060359 ECLASS: 21170231 Material: Special steel Version: Workshop execution Facts Nominal diameter: 5.83 mm Length: 50 mm Tolerance: ±0.001 mm Weight: 0.013 kg Special features Single inspection/gauge pin Supplied in transport case for secure transit Workshop finish for daily use FAQ What is the declared tolerance of the gauge pin? The declared tolerance is ±0.001 mm for the M323.583 gauge pin (Metav IndustryLine), suitable for micrometric reference checks. Is the pin suitable for use in inspection fixtures and jigs? Yes, the M323.583 inspection pin is designed for fixture integration and end‑measure reference use in workshop metrology applications. What material is the pin made from and how does that affect durability? The pin is manufactured from special steel, which provides enhanced wear resistance and robustness for routine shop‑floor handling. Does the product come with protective packaging? The M323.583 is supplied in a protective transport case to reduce handling damage during storage and transit. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
5.84mm Gauge Pin, Single, ±0.001mm Accuracy, 50mm Length, Workshop Grade, Special Steel - Metav IndustryLine
Take advantage of the combination of ±0.001 mm accuracy, compact 5.84 mm diameter and robust special‑steel construction for reproducible final‑dimension checks; order the gauge pin directly via Metav Werkzeuge or ask our consultants if needed. Gauge pin M323.584 — Single precision pin, 5.84 mm, ±0.001 mm, 50 mm length (Metav IndustryLine) The gauge pin M323.584 is a workshop‑grade precision reference for end‑measure and go/no‑go gauging in inspection and assembly environments Workshop-grade precision design Diameter 5.84 mm with ±0.001 mm tolerance Hardened special-steel construction 50 mm cylindrical length for end measurements Reliable dimensional control for final inspection Precision and repeatability are central to efficient quality assurance. The compact cylindrical reference pin delivers a tight tolerance of ±0.001 mm, which makes it suitable for critical end‑dimension verification where small deviations lead to rework or scrap. By using a dedicated hardened reference pin, measurement variance due to instrument play or fixture misalignment is reduced, improving pass rates and shortening inspection cycles. This measurable performance supports faster decision‑making on the shop floor and in incoming goods inspection. Built for workshop durability and handling A workshop execution combines robustness with practical handling: the pin’s special‑steel composition offers wear resistance during repeated seating and extraction in jigs or test fixtures. The 50 mm length balances reach and rigidity, enabling secure engagement in blind bores and through‑holes without excessive deflection. The simple cylindrical form aids quick seating and visual verification, reducing handling time during serial checks and contributing to a smoother production flow. Clear functional advantages in metrology workflows Using a dedicated reference pin streamlines calibration transfers and comparative checks across fixtures. Its nominal diameter of 5.84 mm corresponds to common end‑measure steps, making it a practical choice for tolerance stacks and final assembly gauges. The precise manufacturing tolerance supports reproducible results when establishing reference points or validating bore sizes, thereby lowering measurement uncertainty and supporting traceable quality records for batch acceptance. Practical application and compatibility The compact, single‑piece design is intended for straightforward integration into inspection racks, plug gauges and fixture templates. Its workshop specification makes it suitable for routine end‑measure tasks and go/no‑go verification during assembly. For users seeking to align inspection practice with robust, repeatable controls, this precision reference pin offers a deterministic element to compare against micrometres, height gauges and calibrated master rings. Contact Metav Werkzeuge for tailored advice on using the M323.584 in inspection setups or to reserve stock; call +49 2822 7131930 or email info@metav-werkzeuge.com Technical data Article number: M323.584 GTIN: 4061905060366 Brand: Metav IndustryLine Short description: Gauge pin, single, 5.84 mm, ±0.001 mm, length 50 mm Specifications Diameter: 5.84 mm Length: 50 mm Tolerance: ±0.001 mm Weight: 0.013 kg eClass: 21170231 Materials and features Material: Special steel Workshop execution Category: Gauge pins (Messstifte) Application: End‑measure and reference gauging FAQ What level of accuracy does this gauge pin provide? The gauge pin M323.584 is manufactured to a tolerance of ±0.001 mm, making it suitable for high‑precision end‑measure verifications in workshop environments. Is the pin suitable for repeated use in jigs and fixtures? Yes, the special‑steel construction and workshop specification ensure wear resistance and durability for repeated seating in fixtures and assembly checks. Can this pin be used as a reference for bore verification? The 5.84 mm nominal diameter and tight tolerance allow the pin to act as a reliable reference for bore checks and go/no‑go comparisons in inspection routines. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
5.85mm Precision Gauge Pin ±0.001mm Length 50mm, Workshop Version - Metav IndustryLine
Take advantage of the combination of extreme dimensional accuracy (±0.001 mm), a precise 5.85 mm diameter and robust 50 mm length for reliable end‑measurements; order the gauge pin directly via Metav Werkzeuge or consult the specialists if clarification is required. Metav IndustryLine gauge pin M323.585 — 5.85 mm, ±0.001 mm tolerance A gauge pin 5.85 mm designed as a single inspection pin for demanding end‑measurement and final inspection tasks in workshop environments. Diameter 5.85 mm, tolerance ±0.001 mm Length 50 mm for secure engagement Special steel construction Workshop version; supplied in transport case Precision that prevents rework and speeds inspection The core benefit of this inspection pin lies in its dimensional accuracy (±0.001 mm), which translates into repeatable reference measurements during final inspections. A tolerance at this level reduces uncertainty in go/no‑go checks and minimises downstream rework, improving throughput in quality control processes. The specification is particularly relevant where small clearances and fit tolerances determine assembly success; by using a pin with a verified diameter of 5.85 mm, measurement variations caused by worn or imprecise reference tools are significantly lowered. Design and material for stable, reproducible measurements Manufactured from special steel, the single pin offers a combination of surface hardness and geometric stability that supports repeated use in workshop conditions. The 50 mm length provides enough engagement for stable seating in gauges, fixtures or bore checks while remaining compact for handling. The workshop configuration ensures the component is suited to everyday inspection routines, and the inclusion of a protective transport case preserves the finished surface and prevents contamination during storage and transit. The pin’s low mass (approx. 0.013 kg) makes it easy to position without inducing measurement disturbance. Integration into inspection routines and typical applications This precision pin serves as a reference element for end‑measurements, final acceptance checks and fixture alignment. It is intended for uses where a single, accurately sized datum is required—examples include bore verification, mandrel checks and plug‑gauge substitutes in one‑off or small‑batch inspections. The straightforward, single‑piece design reduces handling steps and simplifies traceability in measurement logs. For procurement and inventory, the item is identified as M323.585 within the Metav IndustryLine range, facilitating rapid replacement and standardisation across inspection benches. Select the Metav IndustryLine gauge pin for exact final measurements and request supply or technical guidance through Metav Werkzeuge in Emmerich: info@metav-werkzeuge.com, +49 2822 7131930 Technical data SKU: M323.585 GTIN: 4061905060373 Label: Prüfstift, einzeln, 5,85mm, +/- 0.001 mm Länge 50 mm Facts Diameter: 5.85 mm Tolerance / Accuracy: ±0.001 mm Length: 50 mm Weight: 0.013 kg Special features Material: Special steel Single pin delivery Workshop design Supplied in transport case FAQ What is the exact tolerance of this gauge pin? The gauge pin M323.585 is specified with an accuracy of ±0.001 mm, suitable for high‑precision end‑measurements. Which material is used for the inspection pin? The pin is made from special steel, chosen for dimensional stability and resistance to wear in workshop conditions. Is the pin supplied individually or in sets? This article is supplied as a single inspection pin (single delivery), designated as M323.585 in the Metav IndustryLine. Can the pin be used for bore checks and fixture alignment? Yes, the 5.85 mm diameter and 50 mm length make the pin suitable for bore verification, mandrel checks and fixture alignment tasks. How is the pin protected during transport? The product is delivered in a transport case to protect the surface and maintain measurement integrity. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
5.86mm Gauge Pin Single ±0.001mm Length 50mm Workshop Version - Metav IndustryLine
High-precision end-dimension checking with a tight ±0.001 mm tolerance and robust special-steel construction ensures reproducible inspection results; the compact 50 mm length eases handling on crowded benches. Order the precision test pin directly via Metav Werkzeuge or ask our consultants if needed. Metav IndustryLine precision test pin M323.586 – Single gauge pin, Ø 5.86 mm, ±0.001 mm tolerance The Test pin M323.586 is a single, high-precision gauge pin designed for reliable end-dimension checks and inspection tasks in workshop and production environments Tolerance ±0.001 mm Diameter 5.86 mm Length 50 mm Workshop-grade special steel Reliable measurement where micrometres matter A compact inspection tool with a stated tolerance of ±0.001 mm, this gauge pin delivers repeatable checks on end faces and small bores where traceable accuracy is required. The fine tolerance places the component in the high-precision range suitable for dimensional control during final inspection or incoming inspection routines. As a single-piece gauge pin, it provides a defined reference diameter of 5.86 mm, enabling quick verification of shafts, holes and mating parts without the need for complex fixtures. The measurable benefit is reduced rework and clearer pass/fail decisions in production. Durable design for busy inspection benches Manufactured in special steel and executed in a workshop-ready finish, the pin combines surface quality with the mechanical robustness expected on inspection benches. The 50 mm overall length offers sufficient engagement while keeping the tool easy to manoeuvre and store; the low mass supports fast handling during repetitive checks. The workshop execution reduces susceptibility to surface damage under normal use and supports reliable contact during tactile gauging. This balance of resilience and precision minimises downtime and preserves dimensional integrity across repeated measurements. Traceability and straightforward integration into quality systems Inventory and quality documentation are simplified by clear identifiers: the article is listed as M323.586 and linked to its GTIN for procurement and audit trails. The single-item supply format suits targeted replacement or selective expansion of a gauge set, while the plain geometry makes the pin compatible with common go/no-go fixtures, locating sleeves and bore gauges. Using a compact, defined-diameter reference aids consistent measurement methodology and supports statistical process control by reducing variable introduction at the inspection stage. For batch enquiries, availability or technical advice on integrating the Metav IndustryLine precision test pin M323.586 into inspection procedures, contact Metav Werkzeuge for tailored support and reliable supply from Emmerich Technical data Article number: M323.586 GTIN: 4061905061035 Category: Gauge pins Brand: Metav IndustryLine Facts Diameter: 5.86 mm Tolerance: ±0.001 mm Length: 50 mm Weight: 0.013 kg Special features Material: Special steel Workshop version Single-item supply SKU: M323.586 FAQ What tolerance can be expected from this test pin? The test pin M323.586 is specified with a tolerance of ±0.001 mm, which supports high-precision end-dimension checks in inspection processes. Which materials is the pin suitable for verifying? As a dimensional reference, the Metav IndustryLine test pin M323.586 is used to check bores and mating parts made from metals and engineering plastics where a fixed diameter reference of 5.86 mm is required. How is the product identified for procurement and inventory? The product is listed as M323.586 and carries GTIN 4061905061035, simplifying ordering and traceability in quality documentation. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
5.87mm Gauge Pin Single, ±0.001mm, 50mm Length, Workshop Version - Metav IndustryLine
Take advantage of the combination of high repeatability, micrometre-level tolerance and a robust workshop design for consistent end‑dimension checks; order the gauge pin directly via Metav Werkzeuge or ask our consultants if needed. Gauge pin M323.587 — 5.87 mm, ±0.001 mm, 50 mm length The gauge pin 5.87 mm is a workshop‑grade test pin for precise end‑dimension verification and fixture checks in inspection and production environments Workshop version design Diameter 5.87 mm precision Tolerance ±0.001 mm Length 50 mm for compact checks Consistent micrometre accuracy for critical measurements The gauge pin M323.587 delivers ±0.001 mm repeatability, making it suitable where very small dimensional deviations matter. Such a tolerance corresponds to micrometre‑class control and supports reliable pass/fail decisions on finished components. By offering a narrow diameter of 5.87 mm, the pin minimises play in small bores and registers, improving measurement certainty during end‑dimension checks and comparative inspections. Built for workshop use with durable materials Designed as a workshop version, the test pin is manufactured from special steel to withstand routine handling and contact with mating parts. The 50 mm length provides a compact geometry that is easy to seat in fixtures and gauges, while the low mass (approx. 0.013 kg) keeps handling comfortable and reduces the risk of displacement during manual checks. Delivery includes a transport case for safe storage and transit, protecting the pin from shocks and contamination. Practical integration into inspection workflows This test pin suits assembly‑line checks, incoming inspection and small‑part verification where quick, repeatable references are required. Used alongside calipers and bore gauges, the pin facilitates fast comparative checks and helps reduce measurement uncertainty in routine quality control. The robust finish and tight tolerance support consistent contact measurement, lowering rework rates and contributing to smoother production throughput. Identification, traceability and delivery scope The article is identified by SKU M323.587 and GTIN 4061905061370 for traceable procurement and stock management. No ISO 17025 calibration certificate is specified for this item; standard delivery comprises the test pin and a transport case as indicated. For applications requiring certified calibration, further options can be arranged through the supplier's calibration services. For workshop calibration and precise end‑dimension control, contact Metav Werkzeuge to arrange supply of the M323.587 gauge pin and to discuss suitable calibration options. Technical data Article number: M323.587 GTIN: 4061905061370 Label: Prüfstift, einzeln, 5,87mm, +/- 0.001 mm Länge 50 mm Numbers / Core technical data Diameter: 5.87 mm Length: 50 mm Tolerance / Accuracy: ±0.001 mm Weight: 0.013 kg eClass: 21170231 Designs / Special features Material: special steel Workshop version (Werkstatt‑Ausführung) Delivery in transport case for protection SKU: M323.587 FAQ What is the declared tolerance of this gauge pin? The declared tolerance is ±0.001 mm for the gauge pin M323.587, suited to micrometre‑level checks. Which material is used for the test pin? The test pin is made from special steel, chosen for wear resistance and dimensional stability during routine workshop use. Is a calibration certificate included? No ISO 17025 calibration certificate is specified for this item; standard delivery includes the pin and a transport case. If a certified calibration is required, Metav Werkzeuge can advise on available services. Can this pin be used for bore and end‑dimension checks? Yes, the 5.87 mm diameter and 50 mm length make the pin suitable for bore checks, end‑dimension verification and fixture referencing in inspection routines. How is the article identified for ordering and stock control? Order and stock using SKU M323.587 or GTIN 4061905061370 for unambiguous identification. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
5.88mm Gauge Pin, ±0.001mm Accuracy, 50mm Length, Workshop Version - Metav IndustryLine
Take advantage of high repeatability, microscopic tolerance and workshop‑grade handling to simplify end‑dimension checks; order the gauge pin directly via Metav Werkzeuge or request advice from our consultants. M323.588 gauge pin, single — 5.88 mm, ±0.001 mm, 50 mm length (Metav IndustryLine) M323.588 gauge pin, single serves as a workshop‑grade precision mandrel for end‑dimension verification and fit checks in metrology and production control. Workshop-grade precision finish Diameter 5.88 mm, tolerance ±0.001 mm 50 mm special-steel length for durability Supplied in protective transport case Precision for repeatable end‑measure inspection The M323.588 is manufactured to a nominal diameter of 5.88 mm with a guaranteed ±0.001 mm tolerance, making it suitable for high‑accuracy end‑dimension checks and tight fit verification. Such a fine tolerance corresponds to micrometre‑scale control and reduces ambiguous fits during assembly; by providing a reliable reference shaft, the pin supports faster decision‑making on pass/fail inspections and helps to minimise rework in series production. The compact geometry and stable tolerance regime also make the pin a useful reference when setting up measuring fixtures or verifying bore sizes on small components. Robust workshop construction for dependable daily use Machined from special steel, the pin combines dimensional stability with a surface finish appropriate for repeated insertions. At approximately 0.013 kg and a 50 mm active length, the tool balances mass and handling to allow quick positioning without excessive play. The item is a workshop version, designed to tolerate the rigours of a busy inspection bench, and it is supplied in a protective transport case to preserve its calibrated condition during storage and transit. This construction lowers the lifetime cost of inspection tooling by maintaining geometry over many cycles. Integration into inspection routines and quality documentation As a standardised reference element, the pin is useful across assembly, incoming inspection and final control stations where tight clearance checks are required. The simple, single‑element design facilitates rapid transfer measurements and compatibility with a wide range of fixtures and gauges. A clear article code and GTIN support inventory management and traceability in quality systems, while the compact format makes the pin straightforward to catalogue within inspection kits. For complex applications or batch planning, Metav IndustryLine documentation can be referenced to ensure the element matches existing inspection protocols. For reliable end‑dimension checks and efficient inspection planning, request the M323.588 gauge pin from Metav Werkzeuge in Emmerich or contact our technical advisers for application guidance Technical data Article number: M323.588 GTIN: 4061905061387 ECLASS: 21170231 Manufacturer: Metav IndustryLine Facts Diameter: 5.88 mm Tolerance / Accuracy: ±0.001 mm Length: 50 mm Weight: 0.013 kg Special features Material: special steel Workshop version for daily inspection use Supplied in a protective transport case Application: end‑dimension checks / fit verification FAQ What tolerance does the gauge pin hold? The M323.588 gauge pin is manufactured to ±0.001 mm tolerance, providing micrometre‑level repeatability suitable for tight clearance checks. Which material is used for this gauge pin? This gauge pin is made from special steel, chosen for dimensional stability and wear resistance in workshop environments. Is the pin supplied ready for storage and transport? Yes, the pin is supplied in a protective transport case to preserve the measuring surface and geometry during handling. What is the intended application of this gauge pin? The tool is intended for end‑dimension checks and fit verification in metrology, assembly inspection and fixture set‑up tasks. How is the item identified for inventory and traceability? The article is identified by code M323.588 and GTIN 4061905061387 to support inventory control and traceability. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
5.89mm Gauge Pin Length 50mm ±0.001mm Workshop Finish - Metav IndustryLine
Take advantage of the combination of workshop-grade robustness, sub-micron accuracy and compact handling for reliable inspection results; order this test pin directly via Metav Werkzeuge or contact our consultants for technical matching. Test pin M323.589 — precision 5.89 mm, tolerance ±0.001 mm, 50 mm length (Metav IndustryLine) A Test pin M323.589 is a workshop-grade cylindrical gauge designed for repeatable end‑measurements and fit checks in inspection and assembly jigs. Workshop version for daily use Diameter 5.89 mm with high fit accuracy Tolerance ±0.001 mm for fine inspection Supplied in transport case for protection Precision engineered for repeatable inspection results The pin is manufactured to a tight ±0.001 mm tolerance on a 5.89 mm diameter, delivering measurement certainty where tight fits and interchangeability matter. This level of control reduces rework and speeds up go/no‑go decisions on the shop floor; the small form factor and 50 mm length make the component easy to insert in gauges, fixtures or comparison blocks. The combination of close dimensional control and a compact footprint supports faster inspection cycles and fewer disputes over part conformity. Robust workshop design that withstands daily handling Built as a workshop version, the test pin uses special steel selected for wear resistance and dimensional stability under repeated use. Surface finish and material choice minimise fretting and scoring during contact with mating parts, extending service life and maintaining gaugeability. Delivered in a transport case, the pin arrives protected against knocks and corrosion during storage and transit, helping to preserve the calibrated geometry and ensuring it is ready for immediate deployment in production routines. Simple integration into inspection workflows and traceability As a single, dedicated test pin, the component fits directly into fixture bores, end‑measuring setups and manual gauge assemblies, promoting standardised checks across stations. The clear specification and traceable SKU allow documentation in inspection plans and tool lists, supporting quality records and audit trails. When consistent plug‑gauge behaviour and repeatable contact geometry are required, this precision pin provides a dependable reference for assembly and measurement tasks. For workshop inspection tasks, request the Metav IndustryLine test pin from Metav Werkzeuge and discuss suitability with our Emmerich team by calling +49 2822 7131930 or emailing info@metav-werkzeuge.com Technical details SKU: M323.589 GTIN: 4061905061394 Manufacturer: Metav IndustryLine Facts Diameter: 5.89 mm Tolerance: ±0.001 mm Length: 50 mm Weight: 0.013 kg ECLASS: 21170231 Special features Workshop version Material: Special steel Supplied in transport case Single test pin FAQ What is the exact tolerance of the test pin? The Metav IndustryLine test pin (SKU M323.589) is specified with a tolerance of ±0.001 mm on the 5.89 mm diameter. Which material is used for this inspection pin? The pin is made from special steel, chosen for durability and stable contact geometry in workshop environments. Is a calibration certificate included with the pin? This workshop‑grade pin is supplied for immediate inspection use and does not include a calibration certificate as standard. How is the pin delivered to protect accuracy? The component is supplied in a transport case to protect the finished geometry during storage and transit. What applications suit this test pin? Typical uses include end‑measurements, fit checks in fixtures and manual gauge assemblies where a precise mating diameter and repeatable contact are required. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
5.8mm Gauge Pin ±0.001mm Length 50mm Workshop Finish - Metav IndustryLine
Precision of ±0.001 mm, a compact 50 mm length and special steel construction ensure repeatable end-measurements in workshop environments; order the pin directly via Metav Werkzeuge or consult our specialists for application advice. M323.580 gauge pin — 5.80 mm diameter, ±0.001 mm tolerance (Metav IndustryLine) The M323.580 is a workshop-grade cylindrical gauge pin intended for accurate bore verification, fixture setting and end-measurement tasks in production environments. Workshop-grade special steel Diameter 5.80 mm, tolerance ±0.001 mm Length 50 mm for end-measurements Supplied in transport case Accurate, repeatable checks for routine metrology Aiming for measurable reproducibility, this cylindrical gauge pin delivers a declared tolerance of ±0.001 mm (±1 µm) on a nominal diameter of 5.80 mm, enabling fine verification of bore diameters and alignment features. The tight tolerance reduces uncertainty in pass/fail decisions and supports traceable in-process checks. In practice, the compact 50 mm shaft length provides a stable contact area for end-measurements while keeping handling straightforward and cycle times short. The precise dimensional data gives a sound basis for statistical process control and minimises downstream rework. Robust design and material for workshop conditions Designed as a workshop-grade tool, the pin is manufactured from special steel selected for wear resistance and dimensional stability under repeated use. The relatively low mass (approximately 0.013 kg) and solid construction reduce susceptibility to bending during insertion and retraction, preserving measurement integrity. Supplied in a protective transport case, the pin remains protected from contamination and mechanical damage during storage and transit, which helps maintain the declared surface condition and tolerance over many inspection cycles. These practical design choices translate directly into lower lifetime cost through reduced replacement frequency. Integration into quality workflows and fixture setup The cylindrical geometry and precise diameter make this pin suitable as a reference for setting up jigs, calibrating holders and checking bores in series production. As a single, traceable reference artefact, it simplifies go/no-go assessments when paired with standardised test procedures. The compact form factor supports easy interchange between manual inspection benches and automated stations where a simple cylindrical gauge is required. Supplied identification such as GTIN 4061905059469 and the article designation enable clear inventory control and integration into calibration schedules. Secure reliable ±0.001 mm workshop measurement by contacting Metav Werkzeuge for procurement and technical guidance on suitable inspection workflows and accessories Technical data Article number: M323.580 GTIN: 4061905059469 Label: Prüfstift, einzeln, 5,80mm, +/- 0.001 mm Länge 50 mm Facts Diameter: 5.80 mm Tolerance: ±0.001 mm Length: 50 mm Weight: 0.013 kg Special features Material: Special steel Workshop execution Supplied in transport case Category: Messstifte FAQ What is the declared tolerance of this gauge pin? The M323.580 gauge pin is specified with a tolerance of ±0.001 mm, suitable for high-precision workshop checks. Which material is the pin made from? The pin is manufactured from special steel designed for wear resistance and dimensional stability in workshop use. Is the gauge pin supplied with protection for transport? Yes, the M323.580 is supplied in a protective transport case to guard against contamination and damage. For which tasks is this gauge pin intended? The pin is intended for bore verification, fixture setting and end-measurement tasks in production and inspection environments. How does the M323.580 support quality processes? With its declared accuracy and traceable identification, the M323.580 serves as a reproducible reference for in-process checks and setup routines Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
5.91mm Gauge Pin ±0.001mm Length 50mm Workshop Version - Metav IndustryLine
Benefit from micron-level control combined with a robust workshop design and compact length for reliable spot checks; the precise 5.91 mm diameter and ±0.001 mm tolerance ensure consistent inspection outcomes. Order the gauge pin directly via Metav Werkzeuge or ask our consultants if needed. Gauge pin M323.591 — inspection pin, Ø 5.91 mm, ±0.001 mm (Metav IndustryLine) Gauge pin M323.591 is a precision-ground inspection pin intended for workshop measurement and dimensional verification in production and quality assurance environments. Workshop version for robust use Diameter 5.91 mm with ±0.001 mm accuracy Precision-ground surface for reliable fit Compact 50 mm length for stable positioning Micron-level accuracy that prevents rework The inspection pin delivers ±0.001 mm accuracy (equivalent to 1 µm), providing an objective reference for bore and hole checks where small deviations matter. Built with a nominal diameter of 5.91 mm, the pin is ground to tight tolerance and finished to provide repeatable contact geometry; this reduces the need for iterative adjustments during set-up and lowers scrap rates. The combination of fine tolerance and a short, rigid profile supports consistent alignment and verification in serial checks. Robust workshop design for everyday use Designed as a workshop version, the pin balances precision with durability. Manufactured from special steel, the component resists wear during repetitive insertions and is suited to routine inspection tasks on the shop floor. Its 50 mm length gives sufficient engagement for secure seating in jigs and fixtures while keeping the effective cantilever low, which helps preserve measurement integrity and improves handling in confined set-ups. Practical integration into quality workflows As a single-piece inspection tool, the pin is ideal for quick go/no-go verifications, alignment controls and end-mass checks in assembly operations. The precision-ground finish ensures stable seating and reduces measurement scatter, which speeds up throughput and supports statistical process control. Supplied under the Metav IndustryLine portfolio, the product benefits from a European quality filter and straightforward availability for maintenance spares or measurement kits. For application advice, availability or to secure workshop-ready precision components, contact Metav Werkzeuge—fast delivery from Emmerich and technical consultancy available on request Technical data Article number: M323.591 GTIN: 4061905061417 Manufacturer: Metav IndustryLine Facts Diameter: 5.91 mm Length: 50 mm Tolerance / Accuracy: ±0.001 mm Weight: 0.013 kg Special features Material: Special steel Workshop version Precision-ground surface Single piece supply SKU: M323.591 FAQ What inspection tasks is this pin suited for? The gauge pin M323.591 is suited for bore checks, alignment validation and end-mass inspections where a tight reference diameter of 5.91 mm and ±0.001 mm accuracy are required. How precise is the diameter on delivery? The delivered inspection pin maintains a tolerance of ±0.001 mm, enabling micrometre-level repeatability for routine quality checks. Is the pin appropriate for repeated use on the shop floor? Yes. The Metav IndustryLine inspection pin is a workshop version made from special steel, designed for regular use in production environments without rapid wear. Can this pin be used as a setting master for fixtures? The precision-ground geometry and 50 mm length make the pin suitable as a setting master for many fixtures and gauging stations that accept a 5.91 mm reference. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
5.92mm Gauge Pin, ±0.001mm Accuracy, Length 50mm, Workshop Version - Metav IndustryLine
Take advantage of the combination of micron-level accuracy, robust special-steel construction and compact handling for consistent dimensional control. Order the test pin directly via Metav Werkzeuge or consult our specialists for application-specific guidance. Test pin M323.592 — workshop-grade precision test pin, Ø 5.92 mm, ±0.001 mm (Metav IndustryLine) The Test pin M323.592 is a single workshop-grade checking pin for end‑measurements and gauge applications, optimised for precise dimensional control in fixtures and inspection rigs. Workshop-grade execution Tolerance ±0.001 mm Diameter 5.92 mm precision 50 mm length for compact handling Micron accuracy for repeatable checks This workshop pin delivers ±0.001 mm tolerance, equivalent to a single‑micrometre resolution, which supports high‑precision verification tasks where reproducibility matters. The tight tolerance reduces measurement scatter when used as a reference or inspection master, making the pin suitable for end‑of‑line checks, gauge blocks or fixture validation. The combination of small form factor and high accuracy enables consistent pass/fail decisions in serial inspection without complex equipment. Built for robust workshop use Manufactured in special steel and specified as a workshop‑grade item, the pin withstands regular handling and routine measuring procedures. The 50 mm length keeps the pin easy to position while providing sufficient engagement for secure seating in fixtures. A protective case is supplied for transport, preserving the calibrated surface and preventing accidental damage during storage or transit, which helps maintain long‑term stability of the datum. Practical handling and integration The pin’s nominal 5.92 mm diameter and single‑piece design simplify installation into custom gauges, test jigs or comparison fixtures. Low mass and compact geometry reduce the risk of cantilever deflection in short‑span set‑ups, while the smooth working surface supports repeatable contact with mating parts. Where a reference with minimal play is required, this pin functions as a reliable datum component in both manual and semi‑automated inspection stations. Contact Metav Werkzeuge for tailored advice on integrating the M323.592 test pin into existing inspection fixtures or for procurement assistance from our Emmerich distribution centre. Technical data Article number: M323.592 GTIN: 4061905061424 Label: Test pin, single, 5.92 mm, ±0.001 mm, length 50 mm Facts Diameter: 5.92 mm Length: 50 mm Tolerance: ±0.001 mm Weight: 0.013 kg Special features Workshop execution Special steel construction Supplied in protective case for transport Single test pin for gauge and fixture use FAQ What level of accuracy does this test pin provide? The test pin provides a tolerance of ±0.001 mm, suitable for micrometre‑class verification and repeatable dimensional checks in workshop and inspection environments. Is the pin suitable for use in gauges and fixtures? Yes. The M323.592 test pin is designed for integration into gauges and fixtures as a reference or checking element thanks to its controlled diameter and compact 50 mm length. What material is the pin made from and how does that affect durability? The pin is made from special steel, chosen to withstand routine handling and to maintain dimensional integrity during standard workshop use. Does the item include any transport protection? A protective case is supplied to preserve the pin during transport and storage, helping to prevent surface damage and maintain its measurement characteristics. Can this pin be used for high‑volume inspection processes? Its micron tolerance and compact form make it suitable as a reference component in repetitive inspection cycles and semi‑automated stations where consistent contact geometry is required. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
5.93mm Gauge Pin Length 50mm ±0.001mm Workshop Finish - Metav IndustryLine
Precise component checks benefit from the combination of a tight ±0.001 mm tolerance, a 5.93 mm diameter and a practical 50 mm length; the special-steel construction and workshop execution ensure reliable everyday use. Order the pin gauge directly via Metav Werkzeuge or ask our consultants if needed. Pin gauge, single, 5.93 mm — workshop pin gauge with ±0.001 mm tolerance and 50 mm length (Metav IndustryLine) Pin gauge, single, 5.93 mm is a compact inspection pin designed for high-precision dimensional checks and go/no-go verification in workshop and shop-floor environments. Workshop-ready precision ±0.001 mm tolerance Diameter 5.93 mm for tight-fit checks 50 mm length suitable for deep measurements Special-steel construction for durability Accuracy for functional verification and quality control A diameter of 5.93 mm combined with a tolerance of ±0.001 mm delivers the dimensional certainty required for functional fits and final inspection tasks. This level of accuracy reduces ambiguous pass/fail decisions when checking mating bores or precise housings; the narrow tolerance converts measurement data into actionable quality-control outcomes. The compact format and repeatable geometry make the gauge ideal for production sampling and incoming‑goods verification, where quick, reliable validation prevents downstream rework and saves processing time. Built for workshop routines and daily handling The workshop execution and special steel construction provide abrasion resistance and sustained dimensional stability under frequent use. At a nominal mass the pin minimises inertial effects during insertion and removal, helping keep measurements consistent across many cycles. Supplied in a protective plastic or wooden case for transport, the single-piece gauge is protected between uses to limit surface damage and preserve the critical diameter. The robust finish and handling-friendly length ensure compatibility with standard inspection benches and portable test setups. Practical integration into measurement workflows Designed as a straightforward verification tool, the inspection pin speeds up go/no-go checks and complements more complex measuring systems without adding process complexity. The compact form factor fits jigs, fixtures and V‑blocks, while the short overall length reduces the risk of bending when used manually. As a dedicated gauge pin, it supports rapid decisions during assembly, final inspection or tool set‑up, improving throughput and reducing scrap through prompt detection of out-of-tolerance conditions. Dependable supply and workshop confidence The single-piece format simplifies traceability and record keeping for routine checks. Metav IndustryLine builds on workshop-focused design principles to offer instruments that are practical, durable and easy to store. The pin’s combination of a tight tolerance, stable material and protective transport case means less downtime for replacements and fewer interruptions to production — a pragmatic choice for workshops aiming for consistent quality without overcomplicating inspection procedures. For workshop-ready, high-precision checks request technical advice or supply information from Metav Werkzeuge — fast delivery from Emmerich and expert consultation available Technical data Article number: M323.593 GTIN: 4061905061431 Label: Pin gauge, single, 5.93 mm, ±0.001 mm, length 50 mm Material: Special steel Facts Diameter: 5.93 mm Length: 50 mm Tolerance: ±0.001 mm Weight: 0.013 kg Special features Workshop execution Delivered in plastic or wooden case for transport Single-piece gauge for end-measure checks Compact, low-mass pin for minimal insertion disturbance FAQ What level of accuracy does this pin provide? The pin gauge offers a ±0.001 mm tolerance, allowing the Pin gauge, single, 5.93 mm to be used for precision fit checks and final inspection tasks where tight dimensional control is required. Is the gauge suitable for repeated shop-floor use? Yes, the Metav IndustryLine inspection pin is a workshop execution made from special steel, designed to withstand frequent handling while maintaining its critical diameter. Does the product come protected for transport? The single-piece gauge is supplied in a protective plastic or wooden case for transport to preserve the surface and ensure continued accuracy during transfer and storage. Can this pin be used for bore verification and go/no‑go checks? The compact format and tight tolerance make this inspection pin well suited to bore verification, mating-fit assessments and quick go/no‑go decisions on the shop floor. Is the gauge appropriate for integration into jigs or fixtures? Its 50 mm length and low mass allow straightforward use in jigs, holders and portable inspection arrangements without introducing significant bending or handling error. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
5.94mm Gauge Pin, ±0.001mm Accuracy, 50mm Length, Workshop Version - Metav IndustryLine
Achieve repeatable end-measurements with the workshop-grade M323.594 pin gauge: 5.94 mm diameter with a tight ±0.001 mm tolerance and a 50 mm usable length, supplied ready for secure transport. Order the pin gauge directly via Metav Werkzeuge or consult our specialists for application advice. Pin gauge M323.594 — workshop pin gauge, 5.94 mm ±0.001 mm, 50 mm length (Metav IndustryLine) The Pin gauge M323.594 is a compact, workshop-grade precision pin intended for end-measurements and dimensional verification in small to medium components Workshop-grade precision test pin Diameter 5.94 mm ±0.001 mm tolerance Length 50 mm for end-measurements Special steel, robust surface finish Supplied in transport case for protection Reliable dimensional verification for compact components The compact design delivers repeatable end-measurements where tight form and size control matter. With a nominal diameter of 5.94 mm and a declared tolerance of ±0.001 mm, the pin sits in the micro range of gauges suited to fine mechanical and small-part inspection. This level of accuracy supports high-confidence go/no‑go checking and dimensional spot checks, reducing uncertainty in assembly or inspection routines. The precision tolerance helps to maintain consistent fits and minimises rework in serial production. Robust handling and protection in workshop environments Built as a workshop version, the pin is manufactured from special steel for wear resistance and dimensional stability under regular use. The 50 mm length provides ample engagement for through‑and‑end measurement tasks while remaining easy to handle and index during inspection. Delivery in a secure transport case protects the gauge surface from damage and contamination, extending usable life and preserving calibrated condition during storage and transit. Practical integration into inspection workflows The pin gauge is optimised for rapid checks and complements existing plug and pin gauge sets or fixture checks used in machining and quality control. Clear identification with SKU M323.594 and GTIN facilitates stock management and traceability in internal quality systems. The combination of compact size, high tolerance and workshop robustness shortens inspection cycles and supports stricter acceptance criteria without complex setup. Use the gauge for verifying bore entries, positional checks and finishing operations where end-measurements define pass/fail decisions. Contact Metav Werkzeuge today for application guidance and local stock availability of the Metav IndustryLine pin gauge M323.594 — Metav Werkzeuge can advise on fitment, compatibility and delivery to your workshop in Emmerich and across Europe. Technical data Article number: M323.594 GTIN: 4061905062285 Manufacturer: Metav IndustryLine Material: Special steel Core measurements Diameter: 5.94 mm Length: 50 mm Tolerance: ±0.001 mm Weight: 0.013 kg Special features Workshop version For end measurements Supplied in transport case High-precision tolerance ±0.001 mm FAQ What is the declared tolerance of this pin gauge? The pin gauge M323.594 is specified with a tolerance of ±0.001 mm for high-precision end-measurements. Which materials is the pin gauge suitable for checking? The gauge itself is made from special steel and is intended for dimensional verification of machined metal and precision components. Is the pin delivered protected for storage and transport? Yes, the gauge is supplied in a transport case to protect the measuring surfaces during storage and transit. Can this pin gauge be used for bore checking and fixture setting? The M323.594 is suitable for bore entry checks, fixture set-up and small-part verification where a compact, high-precision pin is required. How is the product identified for stock and traceability? Identification is via SKU M323.594 and GTIN 4061905062285 for integration into inventory and quality-control systems. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
5.95mm Gauge Pin Single, ±0.001mm Accuracy, 50mm Length, Workshop Version - Metav IndustryLine
Take advantage of the combination of industrial-grade dimensional accuracy and compact form factor: a 5.95 mm diameter with ±0.001 mm tolerance and a 50 mm working length provide reliable reference measurements for inspection and setup tasks. Order the gauge pin directly via Metav Werkzeuge or consult the specialists for application advice. M323.595 — Gauge pin, single, 5.95 mm, ±0.001 mm tolerance The M323.595 is a single workshop-grade gauge pin designed for high-precision end measurements and fixture setting in production and inspection environments. Diameter 5.95 mm ±0.001 mm Length 50 mm workshop execution Made from special steel Single piece supply Precision where consistent results count This workshop-grade measuring element delivers a ±0.001 mm tolerance on a nominal 5.95 mm diameter, making it suitable where repeatable, high-resolution checks are required. As a hardened reference plug, the component reduces uncertainty in comparative gauges and fixture alignment; the tight tolerance supports efficient quality control and lowers the risk of rework by ensuring that mating parts and bores are verified against a stable datum. Robust design for routine inspection tasks Manufactured from special steel, the pin combines wear resistance with a finely finished measuring surface that preserves geometry over repeated use. The 50 mm length offers secure engagement in a wide range of jigs and inspection fixtures while keeping handling straightforward; the low mass supports quick positioning without detracting from dimensional stability. The workshop specification signals suitability for regular use in toolrooms and production benches where durability and practical handling matter. Traceability and process integration The single-piece format simplifies inventory control and traceability in inspection workflows. Identification via GTIN and article references enables clear logging in production records and simplifies procurement. Used as a reference for end measurements, the pin improves the consistency of setup procedures and feeds reliable data into downstream quality assurance processes, supporting better throughput and fewer inspection-related interruptions. Contact Metav Werkzeuge for supply coordination of the Metav IndustryLine gauge pins and for tailored advice on integrating the M323.595 into inspection routines — call +49 2822 7131930 or email info@metav-werkzeuge.com Technical data Article number: M323.595 GTIN: 4061905058455 eClass: 21170231 Core specifications Diameter: 5.95 mm Length: 50 mm Tolerance: ±0.001 mm Weight: 0.013 kg Materials & special features Material: Special steel Workshop execution Single gauge pin Label: Prüfstift, einzeln, 5,95 mm, +/- 0.001 mm Länge 50 mm FAQ What tolerance does the gauge pin offer? The gauge pin is specified with a tolerance of ±0.001 mm, suitable for high-precision inspection tasks associated with fine dimensional control. Which material is used for the pin? The pin is made from special steel and is supplied in a workshop execution that balances wear resistance with a precise measuring surface. For what applications is this pin intended? It is intended primarily for end measurements and fixture setting, where a compact, accurately sized reference plug is required. Is the item supplied as a single piece or in sets? This article is supplied as a single gauge pin in the described specification. How can the pin be identified for stock and traceability? Identification is possible via the article number M323.595 and GTIN 4061905058455, which support inventory and production record keeping. Metav IndustryLine: Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
5.96mm Gauge Pin, ±0.001mm, 50mm Length, Workshop Version, Special Steel, Supplied in Case - Metav IndustryLine
Take advantage of the combination of ultra‑fine dimensional accuracy, robust workshop design and compact handling for consistent end‑measure checks; the 5.96 mm gauge pin achieves repeatable results and is supplied ready for safe transport in a protective case. Order this precision component directly via Metav Werkzeuge or consult the Metav advisers for specification matching. Gauge pin, single — 5.96 mm, ±0.001 mm, 50 mm length (Metav IndustryLine) The gauge pin, single, 5.96 mm, ±0.001 mm, 50 mm length is a workshop‑grade measuring pin intended for precise diameter verification and end‑measure tasks in production and inspection environments. Diameter tolerance ±0.001 mm 5.96 mm nominal diameter 50 mm overall length Special steel construction Supplied in a protective case Precise control where micrometres are not practical The Metav IndustryLine gauge pin M323.596 delivers a tight tolerance of ±0.001 mm, enabling reliable dimensional checks on bores, dowel holes and locating features where repeatability is essential. With a nominal diameter of 5.96 mm, the pin provides a defined reference for pass/fail checks and fixture set‑up without the need for continual adjustment. The narrow dimensional tolerance reduces the risk of scrap and rework by giving a verifiable standard against which internal diameters are assessed. In practice, the pin can be used as a reference mandrel during assembly checks or as a calibration aid for optical comparators and manual gauges, offering a simple, robust alternative to more complex measuring instruments for many routine inspection tasks. Robust design tailored to daily workshop use Constructed from special steel, this workshop variant is designed for everyday handling and retains dimensional integrity under regular use. The 50 mm overall length provides a comfortable working grip while limiting deflection during insertion, and the low mass of 0.013 kg makes handling effortless during repetitive checks. Surface finish and material choice contribute to wear resistance so that the gauge retains its specification over many cycles; repair and replacement intervals are therefore minimised, supporting efficient production workflows. Supplied in a protective case, the pin arrives ready for immediate use and safe transport between inspection stations, reducing the likelihood of transit damage and preserving accuracy. Practical applications and handling advice The pin is intended for end‑measure verification of bores and for use as a reference in fixture alignment and component assembly. Its nominal diameter suits tasks that require a fixed, measurable reference rather than a variable measuring instrument; when used together with feeler gauges or micrometres for complementary checks, it simplifies process control. Handling is straightforward: insert the pin gently into the feature to be checked, observe seating and freedom of fit, and record deviations against the specified ±0.001 mm tolerance. For long‑term reliability, store the pin in its protective case after use and avoid abrasive contact with harder materials that could alter the effective diameter. Contact Metav Werkzeuge for tailored technical advice and to secure the Metav IndustryLine M323.596 gauge pin with ±0.001 mm accuracy; Metav’s advisers in Emmerich can assist with specification checks and delivery options via info@metav-werkzeuge.com or +49 2822 7131930 Technical data Article number: M323.596 SKU: M323.596 GTIN: 4061905058462 Manufacturer: Metav IndustryLine Facts Diameter: 5.96 mm Length: 50 mm Tolerance: ±0.001 mm Weight: 0.013 kg Special features Material: Special steel Workshop version Supplied in a protective case for transport Category: Gauge pins FAQ Is a calibration certificate included with the gauge pin? No calibration certificate is included by default with the Metav IndustryLine gauge pin M323.596. What is the declared accuracy of this measuring pin? The measuring pin carries a declared tolerance of ±0.001 mm, making it suitable for high‑precision diameter checks. For which tasks is this gauge pin most suitable? This pin is intended for end‑measure checks, bore verification, fixture set‑up and other applications requiring a fixed reference for internal diameters. How is the pin delivered and protected during transport? The pin is supplied in a protective case to prevent damage during transport and storage Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
Fast, tactile checks where electronics are impractical
Gauges and test pins provide unequivocal go/no-go results for threads, bores, gaps and radii without relying on electronics. The range covers plug gauges and ring gauges for internal and external threads, feeler gauges and precision feeler strips for micro‑gap assessment, plus probe pins and measuring pins for tactile diameter and pitch checks.
How these tools work in the production environment
Mechanical gauges operate as direct reference standards: a plug gauge or ring gauge verifies conformity to thread profiles and mating ability, while limit gauges separate accept from reject in a single step. Test pins are used to tactilely measure small bore diameters, centre‑to‑centre distances and radii. Manufactured from hardened gauge steel or ceramic and often precision lapped, these instruments deliver immediate physical results that are ideal for incoming inspection, machine‑side checks and final control.
Measurable benefits that affect production performance
- Reduced scrap and rework through rapid, unambiguous pass/fail assessment.
- Increased repeatability thanks to very low measurement uncertainty and fine lapping.
- Lower downtime: quick checks at the machine save cycle time and reduce setup periods.
- Durable construction with high wear resistance from specialised, low‑distortion alloys.
- Versatile delivery formats: individual gauges, organised sets in wooden cases or metre‑length feeler rolls compliant with DIN 2269.
Why Metav is the practical choice for precision supplies
Metav combines decades of expertise with a broad warehouse and quality filtering from Emmerich. As a precision partner for industry, craft and trade, Metav supplies a comprehensive selection of gauges and test pins alongside complementary tools such as precision calipers and setting rings. With over 48,000 customers and a catalogue exceeding 250,000 items, Metav is positioned to supply reliably, reduce vendor complexity and support traceable quality control to national standards.
Summary
Gauges and test pins are indispensable for dependable, repeatable quality assurance where tactile, mechanical verification is preferred. Choose these plug gauges, ring gauges, feeler strips and probe pins when immediate, robust measurement decisions are required on the shop floor.
FAQ
What materials are gauges and test pins typically made from?
Gauges and test pins are usually manufactured from hardened gauge steel for durability and wear resistance; ceramic variants are available where thermal stability and minimal wear are critical.
How do thread gauges ensure mating capability?
Thread plug gauges and ring gauges check flank diameters and thread form against standards, providing a clear go/no‑go verdict that confirms pairability with mating parts.
Which tolerance class should I choose for probe pins and gauge sets?
Select tolerance classes aligned with your inspection requirements; for high‑precision tasks, sets produced to DIN 2269 or equivalent tolerance classes ensure micrometre‑level control and repeatability.
Can feeler gauges measure contact gaps in valve and engine work reliably?
Yes. Feeler gauges and precision feeler strips, supplied either as a fan or metre‑length rolls, allow accurate assessment of valve clearances and contact gaps down to micrometre increments.
How do limit gauges speed up in‑process inspection?
Limit gauges separate good from bad in a single, tactile operation, enabling rapid go/no‑go checks at the machine and reducing both inspection time and the likelihood of human interpretation errors.
Fragen zu diesen Produkten??
Mit mehr als 30 Jahren Erfahrung beraten wir Sie gerne persönlich.
Tel.: +49 2822 7131930
Mail: info@metav-werkzeuge.com