Precision gauge blocks and plug gauges for reliable dimensional control
Mechanical gauge blocks and plug gauges are essential for tactile verification of threads, bores and gap dimensions, providing fast, unambiguous go/no-go results that enhance process reliability and reduce scrap. Designed for industrial metalworking and toolmaking, these precision tools support incoming inspection and final quality checks by delivering traceable measurements in applications such as thread inspection, bore diameter testing and spacing checks. Manufactured from specially hardened, low-distortion alloys and fine-lapped for minimal measurement uncertainty, the range includes thread plug gauges, precision plug gauges and calibration gauge blocks to ensure long-term repeatability and wear resistance.
5.5 mm Limit Gauge Pin With Wear Allowance, Hardened Steel, DIN 7162 - Filetta
Take advantage of the combination of hardened steel construction, DIN 7162 compliance and an integrated wear allowance on the Go side for dependable go/no-go checks in routine inspection. Order the Filetta limit plug gauge directly via Metav Werkzeuge or consult our specialists for application advice. Filetta Limit Plug Gauge G7 — Hardened steel, DIN 7162 A Limit plug gauge for rapid go/no-go verification of small bores during incoming inspection and process control. Hardened steel for long service life Complies with DIN 7162 inspection standard Wear allowance on the Go side Consistent dimensional checks for production quality The Filetta limit plug gauge delivers a compact, robust solution for fast pass/fail inspection of cylindrical bores. Manufactured from hardened steel, the gauge resists wear and maintains dimensional integrity under frequent use, which supports consistent precision in repetitive checks. Conformance with DIN 7162 ensures the gauge geometry and tolerances match established industrial expectations, simplifying documentation and traceability in standardised inspection routines. The incorporated wear allowance on the Go side extends service intervals by permitting controlled material removal while preserving functional acceptance limits. Practical benefits for shop-floor and inspection benches Designed for efficient routine use, this gauge streamlines the decision step between acceptable and non‑conforming workpieces with unmistakeable go/no-go feedback. The compact format suits bench inspection and dedicated control stations where speed and reliability matter; the simple plug engagement avoids time‑consuming measurements while reducing interpretation errors. As a tactile reference tool, the gauge complements digital instruments and micrometres by providing an immediate mechanical check that is quick to apply and straightforward to record in inspection logs. Durable design that lowers operational risk Material choice and standardised manufacture reduce uncertainty: hardened steel construction offers high wear resistance, while the standard compliance reduces the need for custom verification procedures. The wear allowance on the Go side is a practical feature that keeps the gauge serviceable for longer, lowering total cost of ownership and helping maintain process capability between calibrations. For workshops and production lines requiring reproducible go/no-go results, this gauge is a pragmatic component of a robust quality-control toolkit. Contact Metav Werkzeuge today to specify the right Filetta limit plug gauge (MS911.167) for the inspection tasks and to arrange delivery from Emmerich or further technical consultation Technical data Article number: MS911.167 Product: Limit plug gauge Material: Hardened steel Facts Size: 5.5 mm Standard: DIN 7162 Special features Wear allowance on the Go side FAQ What is the primary purpose of this limit plug gauge? The Filetta limit plug gauge MS911.167 is designed for quick go/no-go verification of small bores to determine conformity during incoming inspection and in-process checks. Which material is the gauge made from and why does it matter? Manufactured from hardened steel, the gauge resists wear and maintains dimensional stability, ensuring reliable pass/fail checks over extended use. Does the gauge follow a recognised standard? Yes. The gauge conforms to DIN 7162, which standardises geometry and tolerances for plug-style limit gauges used in industrial inspection. How does the wear allowance affect maintenance intervals? The built-in wear allowance on the Go side permits controlled degradation before the gauge reaches out-of-tolerance condition, extending usable life and reducing the frequency of replacement. Manufacturer / Responsible: Schut Geometrische Meettechniek bv; Duinkerkenstraat 21; 9723 BN Groningen; The Netherlands; +31 50 5877877; schutnl@schut.com
5.5 mm Limit Plug Gauge Wear Allowance On Go Side, DIN 7162 - Filetta
Reliable inspection depends on durable, standardised tools: this limit gauge pin combines hardened steel construction with DIN 7162 conformity and a 5.5 mm nominal diameter to deliver repeatable checks and a measurable wear allowance on the good side. Order through Metav Werkzeuge or contact our consultants for procurement advice. Limit gauge pin — 5.5 mm, hardened steel, DIN 7162 A Limit gauge pin designed for precision go/no-go and bore checks in production and quality control, manufactured to DIN 7162 standards DIN 7162 standardised gauge pins Hardened steel for long service life 5.5 mm nominal diameter Wear allowance on the good side Repeatable inspection built on recognised standards Conformity to DIN 7162 ensures the pin fulfils established dimensional and geometrical requirements, which is critical for consistent go/no-go evaluation. The 5.5 mm nominal diameter is produced and controlled to the standard, so measurements performed with this plug remain comparable across production batches and inspection stations. Using a standardised pin reduces ambiguity in acceptance criteria and supports traceable quality processes, making it suitable for bench checks and inline verification. Engineered for durability and predictable life-cycle performance Constructed from hardened steel, the pin resists surface degradation during repeated insertion and withdrawal. The specified wear allowance on the good side provides a measurable margin that extends usable life while keeping inspection reliability intact; this allowance makes it clear when replacement is due before measurement uncertainty increases. Routine handling requires only basic cleaning and dry storage; these straightforward measures preserve the hardened surface and maintain conformity for longer, reducing downtime and replacement frequency. Practical benefit in workshop and inspection workflows Designed as a straightforward plug gauge, the component supports rapid verification of bore diameters, alignment checks and fit-control tasks where simple, repeatable decisions are needed. In small-series production and maintenance shops alike, the pin provides a fast, rational decision criterion—pass or fail—without elaborate equipment. The robust material and standard conformity make it a pragmatic choice for quality control points where reliable, easy-to-interpret results are the priority, helping to keep production moving with minimal inspection overhead. Discuss procurement and batch options for this Filetta limit gauge pin with Metav Werkzeuge in Emmerich; call +49 2822 7131930 or email info@metav-werkzeuge.com for guidance and delivery details Technical Data Article number: MS911.209 Category: Gauge pins / Pin gauges Manufacturer: Filetta Facts Nominal diameter: 5.5 mm Standard: DIN 7162 Material: hardened steel Special features Wear allowance on the good side Suitable for go/no-go and bore checks Conforms to DIN 7162 FAQ What nominal diameter does this gauge pin have? The Filetta limit gauge pin MS911.209 has a nominal diameter of 5.5 mm, produced to DIN 7162 tolerances. What material is used for the pin? The pin is made from hardened steel, giving it high surface resistance and durability for repeated inspection cycles. How does the wear allowance affect service life? The documented wear allowance on the good side gives a clear limit for replacement, extending usable life while maintaining reliable go/no-go decisions. Is the pin suitable for production-line checks? Yes, the MS911.209 plug gauge is designed for quick pass/fail checks and can be integrated into workshop and production inspection points. Which standard governs the geometry and tolerances of this pin? This gauge pin is manufactured to DIN 7162, which defines the relevant geometric and dimensional requirements. Manufacturer / Responsible: Schut Geometrische Meettechniek bv; Duinkerkenstraat 21; 9723 BN Groningen; The Netherlands; +31 50 5877877; schutnl@schut.com
5.51mm Gauge Pin, Single, ±0.001mm, 50mm Length, Workshop Version - Metav IndustryLine
This compact gauge pin combines ultra‑fine tolerancing with a robust workshop build: ±0.001 mm tolerance on a 5.51 mm diameter and a 50 mm working length ensure reliable end‑dimension checks and repeatable inspection results. Order the gauge pin directly via Metav Werkzeuge or ask our consultants if needed. Gauge pin M323.551 — precision test pin, 5.51 mm, ±0.001 mm, 50 mm length (Metav IndustryLine) The Gauge pin M323.551 is a precision test pin designed for end‑dimension verification and rapid go/no‑go checks in production and workshop metrology. Diameter 5.51 mm with ±0.001 mm tolerance 50 mm length for compact assemblies Special steel for wear resistance Workshop execution with transport case Measure critical diameters with guaranteed repeatability The main strength of this test pin is its high positional accuracy: a diameter of 5.51 mm held to ±0.001 mm provides significantly tighter control than typical workshop gauges. For incoming inspection, assembly checks or final inspection of turned and ground parts, this level of precision reduces uncertainty and supports consistent quality decisions. The compact geometry and low mass contribute to stable contact conditions, improving repeatability in serial checks. Built for frequent use in workshop environments Designed as a workshop execution, the pin balances precision and robustness. The 50 mm length is long enough for reach in many fixtures yet short enough to avoid flexing during hand or fixture probing. Supplied in a protective transport case, the item is protected in storage and on the workbench, making it practical for routine inspection tasks in manufacturing cells and tool rooms where handling and movement are frequent. Material choice that extends service life Manufactured from special steel, the pin resists wear and surface damage that would otherwise affect dimensional fidelity. The hard, precisely finished tip preserves the nominal diameter over repeated use, maintaining measurement confidence and reducing the need for frequent replacement. For applications where surface finish or lubricant residue is present, the material and finish combination minimises adhesion and eases cleaning between measurements. Practical benefits for quality control and process stability Integrating the pin into sampling routines speeds inspection cycles and supports statistical process control: fewer ambiguous measurements mean faster decision loops and lower scrap rates. The combination of a defined nominal diameter, tight tolerance and compact form factor makes the component suitable as a reference gauge in fixture setups or as a go/no‑go element in manual checking. Traceable identification via SKU/GTIN streamlines inventory and calibration records. For precise end‑dimension verification order the Metav IndustryLine gauge pin via Metav Werkzeuge; our consultants can advise on integration into inspection routines — eMail info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: M323.551 SKU: M323.551 GTIN: 4061905059896 ECLASS: 21170231 Facts Diameter: 5.51 mm Tolerance: ±0.001 mm Length: 50 mm Weight: 0.012 kg Special features Material: special steel Workshop execution Supplied in transport case Single test pin for end‑dimension checks FAQ What tolerance does the gauge pin offer and for which tasks is it suitable? The gauge pin provides a tolerance of ±0.001 mm, making the M323.551 ideal for precise end‑dimension verification, fixture checks and repeatable go/no‑go inspections in production environments. Is the M323.551 appropriate for use in assembly fixtures? Yes, the 50 mm length and compact form factor of the M323.551 allow integration into assembly fixtures and jigs where a precise reference diameter is required. What is the material and how does it affect longevity? The pin is made from special steel, chosen for wear resistance and dimensional stability; this helps maintain the nominal diameter and extends service life under routine inspection cycles. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
5.52mm Gauge Pin, Single, ±0.001mm, Length 50mm, Workshop Version, Special Steel in Case - Metav IndustryLine
Take advantage of the combination of workshop-grade construction, ±0.001 mm tolerance and a compact 50 mm length for reliable end‑dimension checks and repeatable fixturing. Order the gauge pin directly via Metav Werkzeuge or ask our consultants if needed. M323.552 Gauge pin — single precision pin, Ø 5.52 mm, ±0.001 mm (Metav IndustryLine) The M323.552 is a single gauge pin engineered for end‑dimension verification and fixture setting in inspection and production environments. Workshop‑grade design for daily use Diameter 5.52 mm with fine tolerance Accuracy ±0.001 mm for repeatable checks 50 mm hardened length for firm seating High‑precision checks that reduce rework and throughput loss A compact, single gauge pin delivers a direct advantage in quality control: consistent reference dimensions reduce rework and speed up inspection cycles. The Ø 5.52 mm nominal diameter with a ±0.001 mm tolerance provides a measurement basis that meets tight end‑dimension requirements, making the pin suitable for precision gauging and go/no‑go verification. Explained plainly: tighter tolerance on the reference part lowers uncertainty in subsequent measurements, which supports faster decisions on conformity and reduces production stoppages. Robust construction for reliable, repeatable performance Manufactured from special steel, the pin combines wear resistance with stable geometry over many cycles. The 50 mm length gives a secure anchoring in fixtures and allows reliable engagement in bores or jigs without excessive overhang. The solid build minimises elastic deformation during handling, ensuring that each contact reproduces the intended nominal size. These mechanical characteristics mean fewer tool changes and lower downtime in routine inspection workflows. Practical integration into inspection and fixturing processes The single‑piece design suits manual and semi‑automated set‑ups where a defined reference is required for positioning, alignment or end‑dimension checks. Traceability is supported via the item identifiers and GTIN for inventory and quality records, aiding systematic replacement and calibration planning. Where tight repeatability is essential, use this pin as a fixed reference in fixtures or as a portable reference gauge for quick conformity checks on incoming parts. Contact Metav Werkzeuge for procurement advice or a tailored quote for the Metav IndustryLine M323.552 gauge pin and secure the right fit for inspection and fixture tasks. Technical Data Article number: M323.552 GTIN: 4061905059902 Weight: 0.012 kg Material: Special steel Designation: Single gauge pin Facts Nominal diameter: 5.52 mm Length: 50 mm Tolerance/accuracy: ±0.001 mm Label: Prüfstift, einzeln, 5.52 mm Special features Workshop execution Single‑piece construction Suitable for end‑dimension checks Compact format for fixture mounting FAQ What accuracy can be expected from this gauge pin? The M323.552 is specified with an accuracy of ±0.001 mm, providing high repeatability for end‑dimension checks and precision fixturing. Is the pin suitable for use in fixtures and jigs? Yes. The single‑piece construction and 50 mm length make the pin well suited to fixed fixtures, alignment tasks and portable reference checks in workshop environments. What material is the pin made from and how does that affect wear? The pin is made from special steel, chosen for its combination of hardness and dimensional stability, which improves wear resistance and ensures consistent contact geometry over time. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
5.53mm Gauge Pin ±0.001mm Length 50mm Workshop Version, Special Steel - Metav IndustryLine
Take advantage of the combination of workshop durability, sub-micron accuracy and compact handling for reliable end-dimension checks; order the gauge pin directly via Metav Werkzeuge or consult our specialists for application advice. Gauge pin M323.553 — single test pin, 5.53 mm diameter, ±0.001 mm (Metav IndustryLine) The gauge pin M323.553 is a single, high-precision test pin for end-dimension verification in workshop and inspection environments. Diameter tolerance ±0.001 mm Workshop version with robust finish Length 50 mm for stable handling Supplied in a transport box Precision where minimal deviation matters A tight tolerance of ±0.001 mm on a nominal 5.53 mm diameter turns small differences into reliable decisions during quality control. This accuracy reduces uncertainty in pass/fail checks and supports repeatable measurement processes on assembly lines and inspection benches. The high-resolution specification is particularly valuable in fine mechanical and precision engineering contexts where component fit and functional clearances depend on consistent diameters. Compact, rugged format for everyday inspection With a 50 mm length in a workshop-grade design, this single test pin combines handling stability with space-efficient storage. The shorter, rigid form factor minimises flex during placement and speeds up routine checks without elaborate fixturing. Delivery in a transport box protects the measuring surface during handling and shipping, ensuring the gauge arrives ready for immediate use in shop-floor situations and bench-top inspection tasks. Materials and handling that sustain accuracy Manufactured from special steel, the pin is engineered to retain form under regular use while offering corrosion resistance appropriate for workshop conditions. The low mass of 0.012 kg contributes to easy manipulation when performing sequential measurements yet is sufficient to provide tactile feedback during seating. A well-machined contact surface supports reproducible positioning and reduces influence from handling variations. Practical fit in inspection workflows Designed for end-dimension checks, this single test pin integrates simply into existing measurement sequences: it serves as a reference for plug-type verification, visual gauge routines or manual comparator setups. The compact design suits use at stations for quick acceptance testing and small-batch inspections, supporting throughput without compromising on measurement certainty. The straight, certified geometry eases fixture mounting when longer-term monitoring or comparative studies are required. Purchase or request specification guidance from Metav Werkzeuge for precision end-dimension control with the M323.553 gauge pin, delivered protected and ready for workshop use Technical Data Article number: M323.553 GTIN: 4061905059919 Brand: Metav IndustryLine Category: Gauge pins Core dimensions Diameter: 5.53 mm Tolerance / Accuracy: ±0.001 mm Length: 50 mm Weight: 0.012 kg Special features Material: special steel Workshop version for robust handling Supplied in a transport box for protection Intended for end-dimension checks FAQ Is the diameter tolerance really ±0.001 mm? Yes. The specification lists a tolerance of ±0.001 mm for the M323.553 gauge pin, making it suitable for fine-dimension verification. What are the physical dimensions of the pin? The pin has a diameter of 5.53 mm and a length of 50 mm; weight is approximately 0.012 kg. Is the item supplied individually or in sets? The product is supplied as a single test pin (single unit) under the SKU M323.553. How is the pin packaged for transport? The gauge pin is delivered in a transport box to protect the measuring surface during shipment and handling. For which type of checks is this pin intended? The pin is designed for end-dimension checks and routine workshop verification tasks. Metav IndustryLine: Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
5.54mm Test Pin, Single, ±0.001mm Accuracy, Length 50mm, Workshop Version - Metav IndustryLine
Take advantage of the combination of industrial-grade ±0.001 mm accuracy, a precise 5.54 mm diameter and a compact 50 mm length for reliable end‑measure inspections. Order the gauge pin directly via Metav Werkzeuge or consult our advisors for batch supply and application advice Gauge Pin M323.554 — 5.54 mm, ±0.001 mm precision (Metav IndustryLine) The Gauge Pin M323.554 is a single inspection pin designed for precise end‑measure and dimensional checks in production and quality‑control environments Precision tolerance ±0.001 mm Diameter 5.54 mm, ground finish Length 50 mm for end‑measure checks Supplied individually for selective use Consistent dimensional control reduces rework and inspection time The plug‑style inspection pin delivers repeatable dimensional references thanks to its ±0.001 mm manufacturing tolerance and accurately finished 5.54 mm diameter. In serial inspection and jig checks, a consistently produced datum pin shortens cycle times by reducing measurement uncertainty and limiting part rework. The compact 50 mm length suits confined gauges and portable test fixtures, allowing quick insertion and removal during routine checks. This combination of tight tolerance and compact form supports stable results across multiple inspection points without changing measuring procedures. Durable construction for workshop use and routine handling Manufactured in special steel, the pin is intended for hands‑on workshop environments where robustness and dimensional stability are required. The workshop version designation reflects practicality: individual supply simplifies inventory control and selective replacement when wear occurs. The material choice and precision finish ensure long service life under normal inspection loads, while the single‑piece delivery supports calibration cycles and controlled part rotation without unnecessary surplus stock. Seamless integration into inspection workflows and inventory Designed as an inspection component, the pin fits into existing gauge blocks, test rigs and custom fixtures to serve as a reliable reference for end‑measure verification. Clear traceability (SKU M323.554, GTIN listed in the technical data) eases stock management and procurement. Performance‑driven features yield measurable efficiency gains: fewer measurement disputes, faster pass/fail decisions and a reduction in corrective machining. For tailored batch quantities or specification checks, Metav Werkzeuge provides application advice and procurement support to align gauge supply with production needs Contact Metav Werkzeuge for advice on batch orders, compatibility with existing gauges or assistance selecting the correct inspection pin for specific end‑measure applications Technical data Article number: M323.554 SKU: M323.554 GTIN: 4061905059926 Weight: 0.012 kg Material: Special steel Facts Diameter: 5.54 mm Length: 50 mm Tolerance / Accuracy: ±0.001 mm Special features Workshop version Supplied individually Suitable for end‑measure inspection Compact plug‑style form for fixtures FAQ What is this gauge pin primarily used for? The M323.554 gauge pin is intended for end‑measure and dimensional checks in production and inspection fixtures, acting as a precise reference pin for pass/fail and comparative measurements. Does the pin come with a calibration certificate? Standard delivery does not include a specific calibration certificate; the M323.554 is manufactured to the stated tolerance and can be incorporated into your calibration programme if formal traceability is required. Is the material suitable for routine workshop use? Yes, the pin is made from special steel, designed to withstand regular handling and to maintain dimensional stability under normal inspection loads. Can this pin be used in existing gauge blocks and fixtures? The compact 50 mm length and plug‑style geometry make it compatible with most gauge fixtures and custom jigs that accept 5.54 mm reference pins. How is inventory and reordering simplified for this part? The M323.554 is supplied individually and referenced by SKU and GTIN for easy stock control and repeat ordering Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
5.55mm Test Pin ±0.001mm Length 50mm Workshop Version - Metav IndustryLine
High‑precision gauge pin combining ±0.001 mm tolerance, special steel construction and a compact 50 mm length for reproducible end‑measure checks; supplied as a single workshop‑grade pin in a protective transport box. Order directly via Metav Werkzeuge or consult our technical advisers for application support. Gauge Pin M323.555 – 5.55 mm, ±0.001 mm, 50 mm length (Metav IndustryLine) A gauge pin M323.555 engineered for fine end‑measurement and go/no‑go verification in workshop settings, featuring a 5.55 mm diameter and a 50 mm working length for reliable fit and reference measurements. High-precision ±0.001 mm tolerance 5.55 mm diameter in special steel 50 mm working length for end-measure checks Supplied in a protective transport box Precise dimensions for repeatable inspection results The M323.555 is a single gauge pin specified to ±0.001 mm (1 µm) tolerance, making it suitable where tight clearances and reproducible end‑measurements are required. The controlled diameter of 5.55 mm serves as a reliable dimensional reference in plug and hole checks, assembly verification and component sorting. The compact 50 mm length balances handling ease with sufficient engagement depth for many inspection tasks, while the low mass supports rapid manual positioning without inducing deflection. Material quality and workshop durability Manufactured from special steel, the pin is produced for a workshop environment and designed to withstand regular use in inspection benches and fixture stations. The workshop version finish provides a practical compromise between corrosion resistance and tactile handling for routine quality checks. Supplied as a single unit, the pin is delivered in a protective transport box to reduce the risk of damage during storage and transit and to maintain the measurement surface between uses. How the tolerance benefits production control A tolerance of ±0.001 mm places this gauge pin in the high‑precision segment of inspection tools, enabling confident decisions in go/no‑go checks and dimensional sorting. When used as a reference or a mating plug in inspection jigs, the pin reduces uncertainty in fit assessments and helps keep assembly processes within tighter process windows. Traceable geometry and consistent contact surfaces simplify integration into inspection procedures and comparators where micrometre‑scale accuracy matters. Practical handling, maintenance and integration The pin's straightforward geometry permits easy cleaning and light lubrication of contact zones to preserve measurement accuracy; gentle handling and storage in the supplied box prevent nicks and surface wear. Weighing approximately 0.012 kg, the gauge pin is compact for bench use and compatible with standard pin clamps and micro‑fixtures. For workshops seeking consolidated sourcing, Metav IndustryLine supplies this type as a single, robust inspection element suited to repetitive quality tasks. Contact Metav Werkzeuge today to specify the M323.555 gauge pin for precision end‑measure verification or to request application advice from our consultants in Emmerich. Technical Data Article number: M323.555 GTIN: 4061905060731 Manufacturer: Metav IndustryLine Facts Diameter: 5.55 mm Length: 50 mm Tolerance: ±0.001 mm Weight: 0.012 kg Special features Workshop version Material: Special steel Supplied in protective transport box Single unit delivery FAQ What accuracy can be expected from this gauge pin? The gauge pin is specified to ±0.001 mm, offering micrometre‑level accuracy suitable for tight fit checks and repeatable end‑measurement tasks with the M323.555. Is the gauge pin supplied ready for use out of the box? The M323.555 is delivered as a single workshop‑grade pin in a protective transport box; handling and basic cleaning are recommended prior to first use. Which materials is this pin suitable for when checking parts? The pin itself is manufactured from special steel and is intended as a measurement reference for machined components across common engineering materials where dimensional verification at micrometre accuracy is required. Can this gauge pin be integrated into inspection fixtures? Yes. The simple cylindrical geometry and the 50 mm length make the pin straightforward to mount in pin clamps, jigs or manual inspection fixtures for go/no‑go and reference measurements. How should the gauge pin be stored to preserve accuracy? Store the pin in the supplied protective box in a stable, dry environment and avoid contact with abrasive surfaces; light lubrication can be applied sparingly to inhibit corrosion between uses. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
5.56mm Gauge Pin Single ±0.001 mm Length 50 mm Workshop Version - Metav IndustryLine
Take advantage of the combination of high metrological precision, robust workshop design and compact handling for reliable end‑measure verification; order the (M323.556) directly via Metav Werkzeuge or ask our consultants if needed. M323.556 — Single pin gauge 5.56 mm, ±0.001 mm (Metav IndustryLine) A M323.556 single pin gauge designed for precise end‑measure checks and fixture verification in workshop and inspection environments. High precision ±0.001 mm tolerance 5.56 mm diameter, precision ground 50 mm length, workshop version with case Accuracy that secures reproducible inspection results The M323.556 is engineered to deliver consistent gap and hole checking where reproducibility matters. With a stated ±0.001 mm tolerance and a nominal diameter of 5.56 mm, the gauge pin provides a clearly defined reference for go/no‑go procedures and assembly checks. The fine tolerance corresponds to submicrometre control across mating parts, reducing measurement uncertainty and supporting tighter process control in series production or sample inspection. Robust design to keep workshop processes running Constructed from special steel in a dedicated workshop version, the pin gauge stands up to everyday handling without compromising accuracy. The 50 mm length offers practical insertion depth for most bench and fixture tasks while remaining easy to handle; the low mass also minimises operator fatigue during repetitive checks. Delivered in a protective case for transport and safe storage, the item is prepared for workshop use and routine inspection sets, reducing the risk of damage between operations. Integrates simply into quality workflows and tooling sets As a precision pin gauge, this item suits end‑measure verification, fixture setup and gauge‑making tasks where a stable reference diameter is required. The small form factor makes it straightforward to include in inspection trays or gauge blocks, and the traceable identifier GTIN 4061905060748 supports inventory tracking and procurement. Metav’s stock and logistical presence in Emmerich ensure steady supply and simplified replacement planning for production environments that demand continuity. Contact Metav Werkzeuge today to specify the M323.556 for inspection kits, confirm availability at Emmerich and arrange delivery directly from stock. Technical data Article number: M323.556 GTIN: 4061905060748 Brand: Metav IndustryLine Facts Diameter: 5.56 mm Tolerance: ±0.001 mm Length: 50 mm Weight: 0.012 kg Special features Material: Special steel Workshop version Supplied in protective case ECLASS: 21170231 FAQ What tolerance does the pin gauge provide and what is it suitable for? The M323.556 single pin gauge from Metav IndustryLine provides a tolerance of ±0.001 mm and is suitable for end‑measure verification, fixture checks and precise go/no‑go assessments in workshop and inspection contexts. Is calibration information included with this item? No calibration information is stated in the product data for the M323.556; the listing does not specify delivery with a calibration certificate. How is the pin gauge protected during transport? The M323.556 is supplied as a workshop version with a protective case for transport and safe storage to reduce the risk of damage. Can the gauge be integrated into existing inspection sets? Yes, this precision pin gauge is compact and intended for easy inclusion in inspection trays, gauge sets and fixture tooling for routine dimensional checks. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
5.57mm Test Pin ±0.001mm Length 50mm Workshop Version - Metav IndustryLine
Combine sub-micron repeatability, workshop-grade robustness and a compact 5.57 mm diameter for reliable end-measurements; order the test pin directly via Metav Werkzeuge or speak with our consultants for specification advice. Test pin M323.557 – single gauge pin 5.57 mm, ±0.001 mm (Metav IndustryLine) The Test pin M323.557 is a workshop-grade single gauge pin designed for precise end-measurements and go/no-go checks in precision assembly, quality control and small-part inspection. ±0.001 mm measurement tolerance Nominal diameter 5.57 mm 50 mm length in special steel Workshop version supplied with transport case Precision that reduces rework and speeds inspection cycles A compact gauge pin with a ±0.001 mm tolerance delivers measurable advantages on the shop floor: fewer false rejects, faster pass/fail decisions and predictable fit checks during assembly. Made from special steel, the pin keeps dimensional stability under frequent use and supports repeatable seating in gauges and fixtures. The short 50 mm length helps to minimise bending and handling error, which is especially valuable for rapid sampling in production runs. Micro-class size for fine-mechanical applications With a nominal diameter of 5.57 mm, the component sits in the micro measurement class (maximum range up to 100 mm), offering the stiffness and handling benefits required for watchmaking, small housings and precision connectors. The compact geometry provides good access to confined bores while remaining easy to seat and remove. The single-piece design simplifies traceability and reduces the number of moving parts in inspection routines. Practical workshop design for everyday reliability The workshop version construction focuses on serviceability and robustness rather than laboratory fragility. Surface finish and material selection ensure stable contact conditions during repeated insertions. Supplied in a protective transport case, the pin is protected during storage and transit, which helps maintain accuracy and extends service life. The lightweight 0.012 kg mass also makes the pin convenient for handheld inspection tasks. Integration into measurement workflows and benefits Use the pin for end-stop measurements, go/no-go fitting checks and fixture set-up where a deterministic reference diameter is required. The precise tolerance reduces uncertainty in pass/fail thresholds and supports higher throughput in inspection processes by cutting decision time. As a single, traceable gauge element, it is suitable for both spot checks and routine quality control, offering a straightforward route to improved process stability. For procurement or technical clarification regarding the M323.557 test pin, contact Metav Werkzeuge in Emmerich to arrange supply or a detailed specification discussion Technical data Article number: M323.557 GTIN: 4061905060755 Label: Prüfstift, einzeln, 5,57mm, +/- 0.001 mm Länge 50 mm Manufacturer brand: Metav IndustryLine Facts Nominal diameter: 5.57 mm Length: 50 mm Tolerance / accuracy: ±0.001 mm Weight: 0.012 kg Special features Material: special steel Version: workshop execution Delivery: protective transport case included Typical use: end measurements, fitting checks FAQ What inspection tasks is this gauge pin suited to? The M323.557 test pin is intended for end-measurements, go/no-go fitting checks and fixture set-up where a 5.57 mm reference diameter with ±0.001 mm tolerance is required. Is the pin suitable for repeated shop-floor use? Yes, the workshop execution and special steel construction make the M323.557 robust enough for frequent insertions and routine quality-control sampling. How does the nominal diameter affect application choice? At 5.57 mm the pin falls into the micro-class range for fine-mechanical work; it is therefore appropriate for small bores, connectors and precision components where access and stiffness matter. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
5.58mm Test Pin ±0.001mm Length 50mm Workshop Version - Metav IndustryLine
Take advantage of the high repeatability of a precision probe with ±0.001 mm tolerance and a compact 5.58 mm diameter for reliable end‑measure checks; order the inspection pin directly via Metav Werkzeuge or contact the consultants for application advice. M323.558 Inspection Pin — 5.58 mm, ±0.001 mm (Metav IndustryLine) A M323.558 inspection pin engineered for accurate end‑measurement and gauging in workshop environments, offering a 50 mm gauge length and workshop‑grade robustness. Precision tolerance ±0.001 mm Diameter 5.58 mm nominal Length 50 mm workshop version Delivered in protective transport case Repeatable end‑measure control for production workflows The probe provides repeatability that supports tight inspection routines: the ±0.001 mm tolerance makes it suitable for final dimensional checks and comparison gauges where deviations must be minimised. As a single‑piece inspection tool with a 5.58 mm nominal diameter and a 50 mm length, it is compact enough for confined fixture spaces but long enough to reach recessed features. The certified accuracy (stated tolerance) reduces uncertainty in pass/fail decisions and enables faster throughput in quality control without repeated set‑up. Built for daily workshop use with corrosion‑resistant construction Manufactured from special steel, the component is specified as a workshop version, delivering resistance to knocks and routine handling while maintaining measuring integrity. The material choice balances hardness and wear resistance so that contact surfaces keep geometry over many cycles. The item’s low mass (approx. 0.012 kg) aids in handling during manual gauging and minimises influence on lightweight fixtures. Delivery in a protective transport case preserves the polished measuring surface during storage and transport, ensuring the tool arrives ready for immediate use. Practical traceability and integration into inspection routines This inspection pin is designed to fit existing gauges and fixtures used for end‑measure verifications and is identified by GTIN 4061905060762 for inventory and traceability processes. The clear specification of diameter, length and tolerance allows it to be used as a reference member in assemblies, in fixture set‑up, or as a spare for precision measuring jigs. The concise specification list simplifies procurement and reduces mismatch risk: the combination of compact form and high accuracy supports both corrective and preventive quality regimes. Contact Metav Werkzeuge today to confirm the fit of this Metav IndustryLine inspection pin for your application or to reserve stock of items with ±0.001 mm accuracy Technical data Article number: M323.558 GTIN: 4061905060762 Description: Inspection pin, single, 5.58 mm, ±0.001 mm, length 50 mm Facts Diameter: 5.58 mm Tolerance: ±0.001 mm Length: 50 mm Weight: 0.012 kg Special features Workshop version Material: special steel Delivered in protective transport case Suitable for end‑measure checks and fixture use FAQ What level of accuracy does the inspection pin provide? The inspection pin is specified with a tolerance of ±0.001 mm, providing the high accuracy required for fine end‑measure checks. Is the pin suitable for use in workshop fixtures? Yes, the workshop version is designed for routine fixture use and manual gauging while maintaining dimensional stability. What material is the pin made from? The pin is manufactured from special steel chosen for wear resistance and durability in inspection applications. What are the exact dimensions of the component? Diameter is 5.58 mm and length is 50 mm; the product is listed under article number M323.558. How is the item delivered to protect the measuring surface? The pin is supplied in a protective transport case to prevent damage during storage and transit. Can the pin be used as a reference member for traceability? Yes, with GTIN 4061905060762 the probe is suitable for inventory control and traceability within inspection routines. Metav IndustryLine: Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
5.59mm Gauge Pin Single, ±0.001mm Accuracy, Length 50mm, Workshop Version, Special Steel - Metav IndustryLine
Take advantage of the combination of extreme measurement accuracy, robust workshop design and easy integration into quality workflows to secure consistent end‑size control. Order the gauge pin directly via Metav Werkzeuge or contact our consultants for application advice. Gauge pin M323.559 — 5.59 mm, ±0.001 mm tolerance, 50 mm length (Metav IndustryLine) A precision gauge pin, Gauge pin M323.559, engineered for end‑size verification and routine inspection tasks in workshop and production environments. Workshop version for robust daily use Diameter 5.59 mm with ±0.001 mm accuracy 50 mm hardened special‑steel construction Single gauge pin for end‑size control Engineered accuracy for reliable end‑size verification The inspection pin offers a diameter of 5.59 mm with a guaranteed dimensional tolerance of ±0.001 mm, making it suitable for tasks where reproducible end‑size checks are decisive. Such a tight tolerance corresponds to sub‑millimetre inspection demands in precision assembly and final quality control. The fine accuracy reduces the need for secondary verification, shortening inspection loops and supporting a rational, efficiency‑oriented quality routine. Robust construction and practical handling for workshops Manufactured from special steel and finished for workshop durability, the pin combines corrosion resistance and wear performance with a convenient 50 mm length for stable seating in fixtures and holders. At approximately 13 g, the component is lightweight for easy handling while retaining sufficient mass for tactile location and repeatable placement. The workshop configuration is tailored to withstand frequent use, reducing downtime and replacement frequency in daily production. Seamless integration into measurement processes and stock management Delivered as a single inspection unit, the pin fits into established end‑size control workflows and can be used for direct plug checks or as a reference in fixture calibration. The product carries a GTIN for straightforward inventory tracking and traceability within procurement systems. Backed by Metav’s supply chain and quality assurance, the pin supports predictable reordering and consistent availability, helping maintain uninterrupted inspection regimes on the shop floor. For tailored application advice or to arrange supply of the Metav IndustryLine gauge pin M323.559 for precision end‑size control, contact Metav Werkzeuge at info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: M323.559 GTIN: 4061905060779 Brand: Metav IndustryLine Facts Diameter: 5.59 mm Tolerance: ±0.001 mm Length: 50 mm Weight: 0.013 kg Special features Material: special steel Workshop version for frequent use Single item delivery Category: Gauge pins FAQ What is the main application of this gauge pin? The gauge pin M323.559 is designed for precise end‑size verification and routine inspection tasks in workshop and production environments. Is the tolerance of ±0.001 mm suitable for assembly checks? Yes, the ±0.001 mm tolerance of this Metav IndustryLine gauge pin meets tight assembly and final inspection requirements where sub‑millimetre consistency is required. What material is used for the pin and how does it affect durability? The pin is made from special steel, a deliberate choice that enhances wear resistance and longevity for frequent workshop use. How should this pin be stored to preserve accuracy? Store the inspection pin in a clean, dry environment and protect it from impacts; the GTIN facilitates inventory tracking to ensure consistent handling and replacement scheduling. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
5.5mm Gauge Pin ±0.001mm Length 50mm Workshop Version - Metav IndustryLine
A compact workshop-grade gauge pin combining ±0.001 mm dimensional accuracy with a 5.50 mm diameter and a 50 mm working length for reliable end‑measurement checks and fixture setting; order the pin directly via Metav Werkzeuge or consult our specialists for application advice. Gauge pin M323.550 — Single workshop test pin, 5.50 mm, ±0.001 mm The gauge pin M323.550 is a single, workshop‑grade inspection pin designed for precision checking, alignment and end‑measurement tasks in metalworking and assembly environments. Tolerance ±0.001 mm precision Diameter 5.50 mm nominal Length 50 mm, workshop grade Special steel construction Delivered in protective transport case Minimal uncertainty for pass/fail and set‑up checks A tolerance of ±0.001 mm positions this inspection pin among high‑precision workshop tools suitable for tight Go/No‑Go checks and comparative measurements. The fine tolerance reduces measurement scatter in routine inspection tasks and supports consistent set‑up of jigs and fixtures. By keeping a predictable nominal diameter of 5.50 mm, the pin functions reliably as a reference element in inspection stacks and assembly gauges. The combination of small form factor and high repeatability makes it suitable where reproducible gauge dimensions matter for process control. Robust construction for frequent handling and machining environments Made from special steel, this test pin is designed to withstand daily workshop use while maintaining its dimensional integrity. The material choice balances hardness, wear resistance and machinability so that the pin remains true over repeated insertions and contact cycles. At a mass of 0.012 kg and a working length of 50 mm, the component is easy to handle yet offers sufficient engagement depth for many alignment and go‑gauge applications. Supplied in a protective transport case, the pin remains protected from knocks and contamination during storage and transport. Integrates cleanly into inspection and tool‑setting workflows As a single gauge element, the pin serves directly in end‑measurement, plug‑type verification and fixture alignment tasks. Its nominal size and tolerance support straightforward interchange with existing gauge sets and reference inserts; the compact format eases storage in tool drawers or inspection kits. The product’s GTIN 4061905059889 and clear article designation simplify catalogue management and inventory tracking within calibration and quality assurance processes, allowing rapid replacement and traceable part control. Proven source and workshop‑focused delivery Offered under the Metav IndustryLine, this workshop version reflects a supplier strategy that emphasises availability, consistent quality and practical packaging for industrial users. Metav’s European distribution and stock handling ensure reliable supply, while the product’s design focuses on practical benefits for machinists and quality technicians who require repeatable, rugged measuring aids. The small, precise test pin works well as a daily reference in production inspection, toolrooms and maintenance departments. For dependable gauge‑work and repeatable setup results, choose the Metav IndustryLine gauge pin M323.550 and contact Metav Werkzeuge for prompt delivery from Emmerich. Technical Data Article number: M323.550 GTIN: 4061905059889 Manufacturer: Metav IndustryLine Facts Diameter: 5.50 mm Tolerance: ±0.001 mm Length: 50 mm Weight: 0.012 kg Special features Workshop version Material: special steel Delivered in protective transport case Category: Messstifte FAQ What tolerance and dimensions does this gauge pin offer? The gauge pin provides ±0.001 mm tolerance with a nominal diameter of 5.50 mm and a working length of 50 mm, making the M323.550 suitable for tight dimensional checks. Which applications are suitable for this inspection pin? The inspection pin is intended for end‑measurement checks, plug‑type verification, fixture alignment and general set‑up tasks in machining and assembly environments where compact, precise reference elements are required. What material is the pin made from and how does that help? The pin is manufactured from special steel, selected to offer a balance of wear resistance and dimensional stability under frequent handling, which supports long‑term repeatability in inspection routines. Is the pin supplied in protective packaging? Yes, the product is supplied in a protective transport case to reduce risk of damage and contamination during storage and transit. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
5.61mm Test Pin, Single, ±0.001mm, 50mm Length, Workshop Version - Metav IndustryLine
Take advantage of a highly stable measurement reference with a 5.61 mm diameter and an ultra‑tight ±0.001 mm tolerance, combined with a 50 mm shaft in special steel for long‑term repeatability. Order the M323.561 directly via Metav Werkzeuge or consult our specialists for integration into inspection routines. M323.561 — Precision gauge pin (5.61 mm, ±0.001 mm, 50 mm) The M323.561 is a single precision gauge pin intended for end‑measurement and inspection tasks in workshop and production metrology. Diameter 5.61 mm with tolerance ±0.001 mm 50 mm shaft length for end‑measurements Made from special steel for wear resistance Workshop version for everyday measurement tasks Precision where every micron matters The M323.561 functions as a dedicated plug gauge for end‑measurements, offering a diameter of 5.61 mm with a tolerance of ±0.001 mm. Such specification places the pin in the realm of high‑precision inspection tools, where geometric conformity determines acceptance. Using a reference pin with this level of accuracy reduces measurement uncertainty, simplifies go/no‑go checks and supports consistent quality decisions in serial production. The compact geometry ensures stable seating in fixtures and repeatable contact, which is decisive when converting dimensional checks into reliable process data. Built for repetitive workshop use and traceable performance Constructed from special steel and presented in a workshop version, the pin combines surface hardness with dimensional stability to resist everyday wear. The 50 mm shaft provides sufficient engagement for end‑measurement tasks while remaining easy to handle and position in jigs or collets. The robust material choice minimises fretting and abrasion, extending service life and reducing the need for frequent replacements. This balance of durability and dimensional fidelity supports efficient inspection intervals and lowers total cost of ownership in routine quality control. Practical integration into inspection workflows As a standard reference component, the gauge pin integrates easily into manual inspection benches and automated checking stations. The clear, narrow tolerance band simplifies decision logic for operators and PLC‑based inspection systems alike, helping to speed up throughput without compromising traceability. The M323.561’s compact form factor suits confined measuring fixtures and facilitates quick interchange between measuring points. For inventory and procurement, the component is identifiable by its SKU and GTIN, supporting seamless stock management and audit trails across production sites. For reliable precision parts and production‑grade inspection accessories, request the Metav IndustryLine M323.561 via Metav Werkzeuge and consult our Emmerich team for delivery and application advice Technical data Article number: M323.561 GTIN: 4061905061097 eClass: 21170231 Core data Diameter: 5.61 mm Tolerance: ±0.001 mm Length: 50 mm Weight: 0.013 kg Special features Workshop version Material: special steel Intended use: end‑measurements Label: Prüfstift, einzeln, 5,61mm, +/- 0.001 mm Länge 50 mm FAQ Is this gauge pin suitable for serial end‑measurements? Yes. The M323.561 pin, with its 5.61 mm diameter and ±0.001 mm tolerance, is designed for repeatable end‑measurement tasks in production and inspection environments. What material is used and how does it affect wear resistance? The M323.561 is made from special steel, which provides enhanced wear resistance and dimensional stability compared with untreated grades, extending usable service life in workshop applications. Can the pin be used in standard plug‑gauge holders? The pin’s compact form and standard shaft dimensions allow integration into common holders and fixtures used for plug‑gauge checks and alignment tasks. Is a calibration certificate supplied with the pin? No calibration certificate is included by default. Specific calibration or certification can be arranged separately if traceable measurement records are required. How should the gauge pin be stored and maintained? Store the M323.561 in a dry, dust‑free container and keep contact surfaces clean and lightly oiled if stored long term. Handle with care to avoid knocks that could alter the calibrated diameter. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
5.62mm Gauge Pin, ±0.001mm Accuracy, 50mm Length, Workshop Version, Special Steel, Supplied in Case - Metav IndustryLine
Take advantage of the combination of ultra-fine ±0.001 mm tolerance, 5.62 mm diameter and robust special-steel workshop construction to secure reproducible end-measure checks and reduce rework; order directly via Metav Werkzeuge or contact the consultants for application advice. Metav IndustryLine Precision Gauge Pin — 5.62 mm, ±0.001 mm, 50 mm The precision gauge pin is a single gauge pin designed for precise end-measurement and verification tasks in workshop and workshop-quality inspection applications. Workshop-grade special steel construction Diameter 5.62 mm, length 50 mm Ultra-fine tolerance ±0.001 mm Supplied in transport case Minimise rework with sub-micron repeatability A measurement standard with an accuracy of ±0.001 mm provides a clear advantage when parts must meet tight fit and clearance specifications. The pin’s 5.62 mm diameter and 50 mm length make it ideal as a reference for end-face checks, go/no-go comparisons and dimensional verification of mating components. Using a dedicated gauge reduces variability inherent to improvised standards and supports quicker decisions on conformity, which in turn lowers scrap rates and shortens inspection loops. Durable workshop design for everyday inspection Constructed from special steel in a workshop-grade finish, this single gauge pin resists everyday handling and keeps its form under normal inspection loads. The workshop execution balances toughness with surface integrity so the reference face remains stable over repeated use. Supplied in a transport case, the pin is protected from knocks and contamination during storage and transfer, preserving the measurement surface and extending service life. Fits smoothly into standard inspection routines The pin is suitable for use in manual and semi-automated measurement setups as a simple, robust reference tool. It functions well for end-measures, bore checks when used as a fixed mandrel and for checking mating surfaces in assembly validation. The straightforward geometry and tight tolerance make it compatible with optical comparators, micrometres and comparator stands, enabling integration without complex retooling of existing processes. Reliability backed by Metav’s quality filter Sourcing from Metav IndustryLine brings the logistical and quality assurance benefits of a dedicated European supplier. Metav’s presence in Emmerich acts as a local quality filter for the market, supporting consistent availability and traceable product provenance. For production environments where reproducibility and dependable supply are equally important, this workshop-grade gauge pin offers a measurable improvement to routine inspection and part acceptance. For precise end-measurement requirements select the Metav IndustryLine gauge pin and contact Metav Werkzeuge in Emmerich for delivery details and consultancy at info@metav-werkzeuge.com or by phone on +49 2822 7131930 Technical data SKU: M323.562 GTIN: 4061905061851 Label: Prüfstift, einzeln, 5,62mm, +/- 0.001 mm Länge 50 mm Facts Diameter: 5.62 mm Length: 50 mm Tolerance: ±0.001 mm Weight: 0.013 kg Special features Material: Special steel Workshop version Supplied in transport case for transport protection FAQ What level of precision does this gauge pin provide? The gauge pin delivers an accuracy of ±0.001 mm, making it suitable for fine tolerance end-measure checks and high-precision workshop inspections. Is the pin suitable for bore checking and go/no-go tests? Yes, the pin is intended for end-face checks and can be used as a mandrel for bore verification and simple go/no-go comparisons in workshop settings. Which material is used and how robust is it? Made from special steel in a workshop-grade finish, the pin resists normal handling and maintains form for reliable reference use. How should the pin be stored to preserve accuracy? Keep the pin in its transport case when not in use to protect the measurement surface from contamination and impacts and preserve the reference geometry. Can this gauge pin be used in optical or mechanical comparator setups? The simple geometry and tight tolerance make the pin compatible with comparator stands, micrometres and many optical inspection setups for straightforward integration. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
5.63mm Gauge Pin ±0.001mm Length 50mm Workshop Finish - Metav IndustryLine
Take advantage of the combination of ultra‑fine accuracy and robust workshop design for reliable part verification; the 5.63 mm gauge pin with ±0.001 mm tolerance and 50 mm length streamlines dimensional checks and reduces rework. Order directly via Metav Werkzeuge or consult our specialists for application advice. Gauge pin M323.563 — 5.63 mm diameter, ±0.001 mm accuracy (Metav IndustryLine) the Gauge pin M323.563 is a single precision pin for dimensional verification and end‑size control in workshop environments ±0.001 mm accuracy for fine tolerance checks Diameter precisely ground to 5.63 mm 50 mm overall length for stable engagement Made from special steel for wear resistance Accurate verification for critical tolerances The core benefit of this instrument is its exceptional measurement precision: with a tolerance of ±0.001 mm, the pin suits fine end‑size inspection, plug gauge checks and comparator set‑ups where repeatability matters. Ground to a nominal 5.63 mm diameter and a nominal length of 50 mm, the geometry offers stable seating in bores and fixtures, reducing lateral play during measurement. Using a single, hardened and finished pin simplifies process control because the dimensional statement is immediate and verifiable; adopters in toolrooms and small‑batch production gain consistent pass/fail data without complex fixtures. The robust finish on the special steel body also extends service life under periodic insertion cycles. Built for workshop use and reproducible handling Designed as a workshop version, the pin combines practical handling with precision. The 50 mm shaft length balances reach and rigidity so that insertion forces remain low while alignment is straightforward, which helps maintain repeatability across multiple operators. The compact mass (approx. 0.013 kg) minimises inertia during handling and reduces wear on mating surfaces. Supplied in a protective transport case, the piece is ready for secure storage and safe transfer between inspection benches. For manufacturers focused on throughput, the result is quicker verification loops and fewer ambiguous measurements. Integration into quality processes and documentation As a discrete gauge element, this pin is ideal for integration into go/no‑go stacks, reference sets and manual gauging routines. Its simple geometry makes it compatible with micrometre checks, height gauges and comparator fixtures for cross‑validation. Traceable labelling and clear identification (SKU M323.563) support inventory control and calibration scheduling within a quality management system. Choosing a standardised pin for routine checks reduces decision time on the shop floor, supports consistent documentation and helps demonstrate control during internal audits. Contact Metav Werkzeuge for tailored guidance and secure the M323.563 gauge pin for dependable dimensional checks in your inspection routine. Technical data Article number: M323.563 GTIN: 4061905061868 Manufacturer: Metav IndustryLine Facts Nominal diameter: 5.63 mm Tolerance: ±0.001 mm Length: 50 mm Weight: 0.013 kg Special features Material: special steel Workshop version Supplied in transport case Category: Gauge pins FAQ What is the declared tolerance of this gauge pin? The gauge pin M323.563 is manufactured and specified to a tolerance of ±0.001 mm, suitable for fine end‑size verification. Can the pin be used in production gauging fixtures? Yes, the workshop‑grade construction and 50 mm length make this pin appropriate for fixture use, stack gauges and manual inspection routines. Which material is the pin made from and why does that matter? Manufactured from special steel, the pin offers improved wear resistance and surface stability, which prolongs service life during repeated insertions. Is the pin delivered ready for storage and transport? The product is supplied in a protective transport case to prevent damage and to simplify handling between inspection points. How is the item identified for stock and calibration control? The item is listed under SKU M323.563 and GTIN 4061905061868, supporting inventory tracking and calibration scheduling. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
5.64mm Gauge Pin, ±0.001mm Accuracy, 50mm Length, Workshop Version, Special Steel, Supplied in Case - Metav IndustryLine
Take advantage of workshop-grade reliability and laboratory-level repeatability: the pin combines a 5.64 mm diameter with an accuracy of ±0.001 mm in a 50 mm length, making it ideal for end‑measurement fixtures and inspection benches. Order the gauge pin directly via Metav Werkzeuge or consult the Emmerich team for batch supply and availability. M323.564 gauge pin (single) — 5.64 mm, ±0.001 mm by Metav IndustryLine A M323.564 gauge pin designed for precise end measurements and repeatable inspection tasks in workshop and production environments. Workshop‑grade finish, robust for daily use Diameter 5.64 mm with ±0.001 mm tolerance Length 50 mm suited to end‑measurements Supplied in a transport box for safe handling Precision that minimises rework and inspection time Built for tasks where dimensional certainty matters, this gauge pin delivers a tight tolerance of ±0.001 mm, which reduces the need for repeated checks and corrective work. The controlled diameter of 5.64 mm ensures secure seating in test jigs and plug‑gauges, providing a reliable reference for go/no‑go tests or positional checks. As a single‑piece tool presented in a workshop‑grade configuration, it is easy to integrate into existing measurement routines and reduces cycle interruptions in quality control. Durable construction for repetitive production use Constructed of special steel, the pin resists wear under frequent insertion and withdrawal cycles while keeping its roundness and surface finish. The 50 mm length gives sufficient engagement for many end‑measurement applications without unnecessary overhang, helping to maintain alignment and minimise bending moments during use. The workshop version specification indicates an emphasis on robustness and handling, suitable for assembly lines and tool rooms where tools are subject to regular, practical handling. Practical benefits for fixtures and gaging systems Delivered as a single item and supplied in a transport box, the pin is protected during storage and transit, reducing the risk of damage before commissioning. Its compact mass and consistent form make it suitable as a reference piece in fixture construction, alignment procedures or as a replacement pin in modular gaging systems. The simple geometry and exacting specification help streamline calibration intervals and support predictable measurement results when used as an end‑measure reference. Contact Metav Werkzeuge for availability and advice on integrating Metav IndustryLine gauge pins into inspection fixtures or gaging systems Technical data Article number: M323.564 GTIN: 4061905061875 Label: Prüfstift, einzeln, 5,64mm, +/- 0.001 mm Länge 50 mm Core specifications Diameter: 5.64 mm Tolerance / Accuracy: ±0.001 mm Length: 50 mm Weight: 0.013 kg Special features Material: Special steel Designation: Workshop version Packaging: Supplied in transport box Supplied as: Single piece Application hint: End measurements / inspection FAQ What are the exact dimensions and tolerance of this gauge pin? The gauge pin M323.564 has a diameter of 5.64 mm, a length of 50 mm and an accuracy of ±0.001 mm. For which measurement tasks is this pin intended? This pin is intended primarily for end‑measurements and repeatable inspection tasks, making it suitable for fixture references, positional checks and go/no‑go applications. What material and durability can be expected? Manufactured from special steel in a workshop version, the pin is designed for frequent use with good resistance to wear while maintaining geometric stability. How is the product delivered and protected in transit? The item is supplied as a single piece and delivered in a transport box to protect the surface and preserve dimensional integrity. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
5.65mm Gauge Pin Single, ±0.001mm, Length 50mm, Workshop Version, Special Steel, Supplied in Case - Metav IndustryLine
Precision measurement performance is delivered by the combination of ±0.001 mm tolerance and a 5.65 mm diameter in a compact 50 mm length, ensuring repeatable end‑measure checks and secure fixture verification; order the gauge pin directly via Metav Werkzeuge or consult our team for application advice. Gauge Pin M323.565 — Workshop gauge pin, Ø 5.65 mm, ±0.001 mm A gauge pin M323.565 designed for precise end‑measure verification and fixture alignment in workshop environments Workshop version, robust design Diameter 5.65 mm for tight fits Tolerance ±0.001 mm for high precision Length 50 mm, compact handling Repeatable accuracy that reduces rework and waste The combination of a ±0.001 mm tolerance and a compact geometry delivers high‑precision verification for end‑measure and go/no‑go tasks. Such fine tolerance reduces the risk of undetected deviations during assembly or inspection, improving first‑pass yields and lowering downstream rework. The performance is particularly valuable where component fit is critical, for example in tight‑tolerance bores or precision jigs, because the narrow dimensional scatter translates directly into fewer production interruptions and more predictable quality metrics. Compact dimensions for practical workshop use With a diameter of 5.65 mm and a length of 50 mm, this test pin combines reach and manoeuvrability without imposing unnecessary bulk in tight fixtures. The short, stiff geometry is suited to manual handling and bench inspection, and the low mass supports quick, repeatable placement. Manufactured from special steel, the pin resists deformation under typical workshop loads and preserves calibration over many cycles, making it a practical choice where space‑efficient gauging is required and handling speed matters. Traceable identification and workshop integration Marked as a single item with SKU M323.565 and GTIN 4061905057533, the pin is suitable for routine inventory and process documentation. The compact format simplifies storage and deployment in standard inspection sets and allows seamless integration into existing quality procedures. As a workshop‑grade tool it provides a straightforward metrological reference for end‑measure checks, fixture benchmarking and quick conformity tests, supporting systematic quality control without overcomplicating the setup. Contact Metav Werkzeuge for individual advice on incorporating this Metav IndustryLine gauge pin into existing inspection routines and for prompt supply from Emmerich: info@metav-werkzeuge.com, +49 2822 7131930 Technical data SKU: M323.565 GTIN: 4061905057533 Manufacturer: Metav IndustryLine Length: 50 mm Diameter: 5.65 mm Weight: 0.013 kg Tolerance: ±0.001 mm Material: Special steel Version: Workshop execution Packaging: single item delivery FAQ What applications is this gauge pin suitable for? This gauge pin is intended for precise end‑measure checks, fixture alignment and go/no‑go verifications in workshop and production environments; the M323.565 is particularly useful where tight fits and repeatable inspections are required. Is the pin supplied as a single unit or in sets? The product is supplied as an individual gauge pin; the designation indicates a single‑item delivery suitable for integration into inspection sets or for standalone use. What material is the pin made from and why does it matter? Made from special steel, the pin offers wear resistance and dimensional stability under normal workshop handling, which helps maintain the specified ±0.001 mm tolerance over repeated use. Metav IndustryLine: Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
5.66mm Gauge Pin Length 50mm ±0.001mm Workshop Finish - Metav IndustryLine
Take advantage of the combination of industrial robustness, sub‑micron accuracy and compact form factor to stabilise inspection routines and reduce rework. With a tolerance of ±0.001 mm, a Ø 5.66 mm gauge dimension and a 50 mm length, ordering is straightforward via Metav Werkzeuge or technical consultants can be contacted for application advice. Metav IndustryLine gauge pin M323.566 — Ø 5.66 mm, ±0.001 mm, length 50 mm The Metav IndustryLine gauge pin M323.566 is a single precision test pin designed for end‑measurement tasks and fine mechanical inspection in workshop environments Metav IndustryLine gauge pin Ø 5.66 mm Tolerance ±0.001 mm for high precision Length 50 mm workshop execution Made from special steel, weight 0.013 kg Stabilise measurements with sub‑micron repeatability The compact probe is engineered to deliver consistent results where tight tolerances matter. With a tolerance of ±0.001 mm, the component supports repeatable go/no‑go checks and final size verification on short production runs or inspection benches. The small diameter (Ø 5.66 mm) minimises probe intrusion and enables accurate contact on narrow bores and small features, which in turn reduces scrap rates and shortens quality loops. Suited for fine‑mechanical and workshop inspection Classified in the Micro category due to its limited measuring span, this test pin is ideal for precision work on small parts, gauges and fixtures. The 50 mm shank length balances accessibility with rigidity for handheld checking or fixture mounting. Constructed for workshop use, the design is optimised for frequent handling and rapid interchange in measuring assemblies, so throughput in the inspection area can be increased without sacrificing accuracy. Durable construction for everyday shop use Manufactured from special steel, the pin provides wear resistance appropriate for regular contact measurement. The low mass (approx. 0.013 kg) helps to reduce dynamic loading in delicate setups and supports stable positioning during tactile checks. As a dedicated end‑measurement tool, the probe is a pragmatic choice for metrology tasks that require both dimensional certainty and a robust, workshop‑grade build. Secure precise end measurements with Metav IndustryLine components — contact Metav Werkzeuge in Emmerich for specification matching and reliable delivery by phone or e‑mail (+49 2822 7131930 / info@metav-werkzeuge.com) Technical Data Article number: M323.566 GTIN: 4061905057540 Manufacturer: Metav IndustryLine Description: Gauge pin, single, Ø 5.66 mm, ±0.001 mm, length 50 mm Facts Diameter: 5.66 mm Tolerance: ±0.001 mm Length: 50 mm Weight: 0.013 kg Measuring range: 5.66 mm Special features Workshop execution Material: Special steel Intended use: end measurements Accuracy class: ±0.001 mm FAQ How precise is the gauge pin M323.566? The Metav IndustryLine gauge pin M323.566 is specified to ±0.001 mm, making it suitable for high‑precision end measurements and fine inspection tasks. What applications suit this test pin? This single gauge pin is intended for end‑measurement and fine‑mechanical inspection in workshop and fixture environments, particularly where compact probes and tight tolerances are required. What is the material and durability of the pin? The probe is made from special steel, chosen for wear resistance and stable contact behaviour under regular workshop use. Can the pin be used in fixture assemblies and gauges? Yes, the 50 mm length and Ø 5.66 mm diameter make the pin well suited for integration into gauges, fixtures and short‑reach inspection jigs. Metav IndustryLine: Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
5.67mm Gauge Pin, Single, ±0.001mm Accuracy, 50mm Length, Workshop Version - Metav IndustryLine
Precise probe performance and robust workshop construction combine to support repeatable end‑dimension inspections: the ±0.001 mm tolerance and special steel construction deliver consistent results, while the protective case allows safe transport and immediate use in workshop environments. Order the test pin directly via Metav Werkzeuge or consult our specialists for application advice. Precision Test Pin M323.567 — Ø 5.67 mm, ±0.001 mm (Metav IndustryLine) The Precision Test Pin M323.567 is a single workshop‑grade inspection pin for end‑dimension checks and fixture verification in industrial metrology and workshop inspection. Workshop‑grade robustness Ø 5.67 mm with ±0.001 mm tolerance 50 mm length for fixture integration Supplied in a protective case Accuracy that keeps production moving High repeatability is the practical advantage of a ±0.001 mm specification: such fine tolerance reduces ambiguity when checking final dimensions and decreases the risk of rework in serial production. The probe pin functions as a reliable reference in inspection jigs and test fixtures, supporting faster decision‑making during quality control. By converting narrow numerical tolerances into operational certainty, the component helps maintain throughput without sacrificing measurement confidence. Robust workshop design and handling Built as a workshop‑version component from special steel, the pin resists the knocks and handling typical of shop‑floor use. The 50 mm overall length provides secure seating in holders and leaves sufficient protrusion for alignment tasks, while the compact mass minimises inertia during manual handling. Delivery in a protective case preserves the measuring face in transit and storage, ensuring the pin arrives ready for immediate deployment in fixture setups or portable inspection rigs. Typical applications and practical benefits Designed for end‑dimension checks, the pin suits tasks such as gauge setting, fixture verification and reference probing in assembly lines or maintenance bays. As a single inspection pin it integrates cleanly into manual or semi‑automated verification stations, offering a concise solution where tight tolerances are critical. The clear numeric specification and workshop orientation simplify procurement and replaceability, allowing production planners to match inspection hardware directly to quality requirements. For workshop‑grade, high‑precision inspection components choose Metav IndustryLine—contact Metav Werkzeuge for availability and application guidance Technical data Article number: M323.567 GTIN: 4061905058387 EClass: 21170231 Label: Prüfstift, einzeln, 5,67mm, +/- 0.001 mm Länge 50 mm Facts Diameter: 5.67 mm Length: 50 mm Tolerance: ±0.001 mm Weight: 0.013 kg Special features Material: special steel Version: workshop execution Delivery: protective case included Application focus: end‑dimension checks FAQ What tolerance can be expected from this test pin? The pin is specified with a tolerance of ±0.001 mm, which positions it for high‑precision end‑dimension verification in workshop environments. Is the pin suitable for use in fixtures and jigs? Yes, the 50 mm length and workshop‑grade construction make the pin well suited for mounting in fixtures and test jigs; the M323.567 integrates into typical verification setups. What material is used for the probe? The probe is made from special steel, providing robustness for routine workshop handling while maintaining the specified measurement stability. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
5.68mm Gauge Pin, ±0.001mm, Length 50mm, Workshop Version, Special Steel, Supplied In Case - Metav IndustryLine
Take advantage of the combination of workshop-grade robustness, ±0.001 mm dimensional precision and a compact 50 mm length for reliable end‑dimension checks; order directly via Metav Werkzeuge or consult our specialists for application advice. Gauge pin M323.568 — precision 5.68 mm, ±0.001 mm (Metav IndustryLine) A gauge pin designed for straightforward end‑dimension inspection and plug‑gauge tasks, specified at 5.68 mm diameter with a 50 mm length for checks in deeper bores. Workshop version for robust use Diameter 5.68 mm ±0.001 mm 50 mm length for deep bores Delivered in protective transport case Consistent measurement where repeatability matters A compact inspection pin with a specified tolerance of ±0.001 mm supports repeatable pass/fail checks and close‑fit verification in assembly and quality control. The very fine tolerance reduces uncertainty when establishing final dimensions on mating parts, enabling faster decision making on production lines and during set‑up. A clearly defined diameter of 5.68 mm makes the component suitable for comparison against drawing limits and for use as a reference in gauging fixtures. Built for workshop use and long service life Constructed from special steel, this workshop‑specification pin balances surface hardness and resistance to wear without unnecessary brittleness. The workshop version designation indicates components intended for daily handling and transport; the pin arrives in a protective transport case to prevent damage and to keep inspection tools organised. The modest mass supports easy handling for bench testing while preserving the stiffness required for accurate contact measurement. Practical integration in inspection procedures Designed as a single, purpose‑built inspection element, the pin integrates simply into existing gauging sets and plug‑gauge assemblies. Its 50 mm overall length is intended for checks in deeper bores or for reach beyond flanges where short pins would not suffice. Weight and compact form factor allow quick interchangeability in hand‑held routines or fixture checks, streamlining throughput and reducing non‑productive time in routine quality loops. Choose Metav IndustryLine precision—contact Metav Werkzeuge for tailored advice and assured supply from Emmerich: info@metav-werkzeuge.com / +49 2822 7131930 Technical data Article number: M323.568 GTIN: 4061905058394 Category: Messstifte Facts Diameter: 5.68 mm Tolerance: ±0.001 mm Length: 50 mm Weight: 0.013 kg Special features Material: Special steel Workshop version Delivered in protective transport case ECLASS: 21170231 FAQ What is the stated precision of the gauge pin? The M323.568 gauge pin is specified with a tolerance of ±0.001 mm, suitable for precise end‑dimension checks. What material is used for the pin? The pin is made from special steel, selected for durability and surface integrity under repeated contact. What are the diameter and length of the pin? Diameter is 5.68 mm with a 50 mm overall length, designed for measurements in deeper bores. Is the pin supplied in protective packaging? Yes, the M323.568 is delivered in a protective transport case to prevent damage during storage and transit. What applications is this pin intended for? Typical uses include final‑dimension verification, plug‑gauge complements and inspection tasks in workshop and assembly contexts where tight tolerances must be verified. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
5.69mm Gauge Pin, Single, ±0.001mm, 50mm Length, Workshop Finish - Metav IndustryLine
High‑precision workshop test pin combining ±0.001 mm tolerance, compact 5.69 mm diameter and robust special‑steel construction to ensure repeatable end‑measure inspections; order directly via Metav Werkzeuge or consult our specialists for application advice. Gauge pin M323.569 – single test pin, 5.69 mm diameter, ±0.001 mm The gauge pin M323.569 is a workshop‑grade inspection pin designed for end‑measure checks and dimensional control in production and quality environments. Tolerance ±0.001 mm Diameter 5.69 mm Length 50 mm Workshop version design Made from special steel Precision that keeps production stable The compact test pin offers a tolerance of ±0.001 mm, making it suitable where narrow limits and repeatable results matter. Manufactured for inspection tasks, this gauge pin provides a reliable reference for go/no‑go checks, plug gauges and verification of bore diameters. The fine tolerance reduces uncertainty during assembly and helps to avoid costly rework by ensuring that measured components conform closely to specification. Designed for everyday workshop use Built as a workshop version, the pin combines handling convenience with dimensional stability. The special steel construction delivers resistance to wear under regular use while retaining surface finish required for accurate contact measurement. At 50 mm length and only 0.013 kg, the format is easy to integrate into fixtures and portable inspection setups without adding unnecessary bulk, so routine checks remain fast and consistent. Integration and measurement efficiency As a single test pin, the component supports rapid inspection cycles on production lines and in metrology benches. The nominal 5.69 mm diameter and tight tolerance make it especially apt for end‑measure applications and serial inspection of small bores. Using defined, hardened reference pins in measurement routines shortens setup time and clarifies acceptance criteria, which contributes to higher throughput and fewer disputes between production and quality. Traceability, identification and workshop assurance The pin is listed under SKU M323.569 and GTIN 4061905058400 for straightforward inventory control and procurement. Supplied as an individual inspection element, it complements calibration and gauge systems already present in the workshop. Metav IndustryLine’s supply chain focus ensures consistent availability and supports a predictable stocking strategy for inspection tools across manufacturing sites. Choose the M323.569 from Metav IndustryLine for reliable end‑measure checks and contact Metav Werkzeuge in Emmerich for specification advice via info@metav-werkzeuge.com or by telephone on +49 2822 7131930 Technical data Article number: M323.569 SKU: M323.569 GTIN: 4061905058400 ECLASS: 21170231 Facts Diameter: 5.69 mm Tolerance: ±0.001 mm Length: 50 mm Weight: 0.013 kg Special features Workshop version Material: Special steel Single test pin configuration Compact, low‑mass design FAQ What nominal diameter and tolerance does this test pin have? The gauge pin is specified at a nominal 5.69 mm diameter with a tolerance of ±0.001 mm, suitable for precise bore and end‑measure checks. Is the pin suitable for use in fixture and gauge assemblies? Yes, the single‑piece design of the M323.569 is intended for integration in fixtures, plug gauges and handheld inspection tools where a compact, hard reference is required. What material is used and how does it affect wear? The pin is made from special steel, providing a balance between surface hardness and damage resistance for typical workshop inspection routines. Does the product include a calibration certificate? Calibration status is not specified in the product data; the listing does not indicate a supplied calibration certificate. How is the item identified for procurement and inventory? The part is identified by SKU M323.569 and GTIN 4061905058400 for clear ordering and stock control. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
5.6mm Gauge Pin ±0.001mm Length 50mm Workshop Finish - Metav IndustryLine
High-precision test pin with ±0.001 mm tolerance and a compact 5.60 mm diameter provides repeatable end‑measurement references; the workshop design in special steel and delivery in a protective case support durable everyday use. Order directly via Metav Werkzeuge or consult our advisors for application advice. Test pin M323.560 – 5.60 mm diameter, ±0.001 mm tolerance (Metav IndustryLine) The Test pin M323.560 is a precision end‑measurement pin designed for workshop inspection and end‑dimension checks in fine mechanical and toolmaking environments. ±0.001 mm tolerance for micrometre accuracy 5.60 mm diameter with 50 mm length Workshop design in special steel Supplied in protective transport case Precision where it matters most The inspection pin is machined to a ±0.001 mm tolerance, providing micrometre‑grade repeatability for reference and end‑dimension checks. With a compact diameter of 5.60 mm and a length of 50 mm, the component serves as a reliable reference in tight assemblies and gauge setups. Classified in the Micro category (measurement range up to 10–100 mm), this format prioritises rigidity and stability over long spans, making it particularly well suited to fine mechanical tasks such as component end‑measurements, small bore gauges and precision fit tests. The narrow profile minimises sag and contact ambiguity, so measurement variation is reduced and inspection throughput becomes more consistent. Built for routine workshop use Constructed from special steel and labelled as a workshop execution, the pin combines dimensional fidelity with day‑to‑day durability. The robust material selection supports repeated handling and insertion without rapid wear of the critical diameter. The compact mass (approx. 0.013 kg) and the short, stiff geometry ensure secure seating in fixtures and gauges; handling is straightforward and positioning is fast, which streamlines inspection cycles. Supplied in a protective transport case, the item remains shielded during storage and movement, reducing the risk of damage to the reference surface and preserving long‑term accuracy. Practical integration and application As an end‑measurement reference, this pin is useful for setting limits, verifying bores or serving as a master datum in assembly checks. Its precision rating and compact form factor make it compatible with bench fixtures, portable measuring rigs and comparative measuring procedures where a small, stable reference is required. The product bears the internal article code M323.560 and is traceable by GTIN for inventory and quality‑management processes. Use of a standardised, tight‑tolerance inspection pin reduces uncertainty in repeat measurements and supports reliable decision making in production and quality control. Choose the Metav IndustryLine M323.560 for consistent end‑measurements and long‑term workshop reliability — contact Metav Werkzeuge in Emmerich for application guidance or to place an order via info@metav-werkzeuge.com or +49 2822 7131930 Technical specifications Article number: M323.560 GTIN: 4061905060786 Brand: Metav IndustryLine Key measurements Diameter: 5.60 mm Length: 50 mm Tolerance: ±0.001 mm Weight: 0.013 kg Measurement range category: Micro (≤ 10–100 mm) Special features Workshop execution Material: Special steel Supplied in protective transport case ECLASS: 21170231 FAQ What level of accuracy does the test pin provide? The test pin M323.560 is manufactured to a tolerance of ±0.001 mm, delivering micrometre‑level accuracy suitable for precise end‑measurements. For which applications is this inspection pin suitable? The inspection pin is intended for end‑dimension checks, reference seating and small‑bore verification in fine mechanical, toolmaking and workshop inspection tasks. Is the pin delivered ready for use and protected during transport? Yes, the item is supplied in a protective transport case to preserve the reference surface and support safe handling between workstations. Which material is used for the pin and why does it matter? The pin is made from special steel; this provides dimensional stability and wear resistance appropriate for routine workshop use. How is the product identified for ordering and inventory? The article number is M323.560 and the product can be referenced by GTIN 4061905060786 for procurement and stock control. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
5.71mm Gauge Pin, Single, ±0.001mm, Length 50mm, Workshop Grade - Metav IndustryLine
Take advantage of the combination of ultra‑fine tolerance and compact form for reliable end‑measurement and assembly checks; the solid special steel construction supports repeated workshop use. Order the gauge pin directly via Metav Werkzeuge or consult the team for application advice. Gauge Pin M323.571 — Precision 5.71 mm, ±0.001 mm, 50 mm length (Metav IndustryLine) The Gauge Pin M323.571 is a single precision test pin designed for end‑measurement and alignment tasks in inspection and workshop environments High‑precision tolerance ±0.001 mm Diameter 5.71 mm for tight fit checks 50 mm overall length for in‑fixture reach Workshop version made from special steel Precision where tolerances decide quality Small deviations can cause costly rework; this gauge pin delivers an accuracy of ±0.001 mm, making it suitable for fine inspection tasks and end‑measure verification. The nominal diameter of 5.71 mm is manufactured to tight limits to ensure repeatable fits in bores and gauge fixtures, which helps to reduce measurement uncertainty and throughput interruptions. As a measuring artefact with a 50 mm length, it supports both surface and depth checks while maintaining dimensional stability. Robust construction for repeated workshop use Constructed from special steel and presented as a workshop version, the pin balances hardness and toughness for regular handling. The component is lightweight at 0.013 kg, easing manual positioning while preserving rigidity during measurement. The 50 mm length offers sufficient reach for many test setups without compromising handling, so mounting and extraction remain straightforward in the shop environment. Practical applications and handling benefits This precision test pin is intended for end‑measure checks, alignment of fixtures and go/no‑go verification of small bores. Its form factor supports easy integration in inspection benches and assembly jigs; the slim diameter is ideal where clearance is limited. Using a dedicated gauge pin speeds up repetitive checks and decreases machine downtime by providing a fast, unambiguous reference for pass/fail decisions. Traceability and dependable supply for production workflows The component is supplied with traceable identification and is part of a dependable product range intended for industrial use. Selecting this gauge pin contributes to a consistent metrology routine and, when stocked through a reliable distributor, supports uninterrupted production. Metav’s catalogue approach provides access to extensive measurement supplies and a transparent logistics base from Emmerich, enhancing procurement security for precision workshops. For precise end‑measurement and fixture checks, choose the Metav IndustryLine gauge pin M323.571; contact Metav Werkzeuge in Emmerich for ordering and technical consultation via info@metav-werkzeuge.com or +49 2822 7131930 Technical data Article number: M323.571 GTIN: 4061905058424 ECLASS: 21170231 Key measurements Diameter: 5.71 mm Tolerance: ±0.001 mm Length: 50 mm Weight: 0.013 kg Materials & features Material: Special steel Product type: Gauge pin / Test pin Version: Workshop execution Designed for end‑measurement applications FAQ What is the declared tolerance of this gauge pin? The declared tolerance for the gauge pin M323.571 is ±0.001 mm, suitable for fine inspection tasks. Which material is used for the test pin? The M323.571 is manufactured from special steel, specified for workshop durability. For which applications is this pin intended? The pin is intended for end‑measure verification, fixture alignment and small‑bore fit checks in inspection and assembly settings. What are the key dimensions to note? Key dimensions are 5.71 mm diameter and 50 mm length; the item weight is 0.013 kg. How is the product identified in inventory systems? Identification: SKU M323.571; GTIN 4061905058424. Metav IndustryLine: Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
5.72mm Gauge Pin, Single, ±0.001mm Accuracy, Length 50mm, Workshop Version - Metav IndustryLine
Take advantage of the combination of ultra‑fine ±0.001 mm tolerance, compact 5.72 mm diameter and robust special steel construction for reliable end‑measurement control in workshop environments; order the part directly via Metav Werkzeuge or consult our specialists for application advice. Gauge pin M323.572 — 5.72 mm, ±0.001 mm, 50 mm length (Metav IndustryLine) A gauge pin (5.72 mm, ±0.001 mm, 50 mm) engineered for precise end‑measurements and repeatable fit checking in workshop settings. Precision tolerance ±0.001 mm Diameter 5.72 mm Length 50 mm Special steel, workshop grade Precision where it counts for assembly and inspection The fine ±0.001 mm tolerance delivers a measurable advantage when verifying end fits, seating depths or bore interfaces. As a single‑piece gauge pin, it provides a stable reference dimension that reduces uncertainty in comparison checks and inline control. The controlled diameter specification of 5.72 mm ensures repeatable contact geometry, which translates into fewer rework cycles and more predictable assembly outcomes. Built for repetitive workshop use with consistent wear resistance Constructed from special steel, this inspection pin combines surface hardness with dimensional stability under normal workshop handling. The 50 mm overall length offers a practical engagement depth for many end‑measurement tasks while keeping the component light at approximately 0.013 kg, facilitating quick manual manipulation and fast cycling on the shop floor. The workshop‑grade finish mitigates premature wear and helps preserve the reference dimension during standard use. Simple integration into gauging processes and fixtures The compact diameter and standardised geometry make the pin suitable for use with pin blocks, fixture seats or bespoke test rigs. As a single test element, it supports efficient verification routines for batch inspections as well as ad‑hoc checks during setup operations. The clear dimensional labelling and GTIN allow straightforward inventory control and traceability within established quality workflows. Reliable measurement behaviour and operational benefit By using a purpose‑made inspection pin, measurement variance due to ill‑fitting tools is reduced and inspection throughput can be increased without sacrificing confidence in results. The product’s specification and workshop orientation provide a pragmatic balance between precision and robustness, supporting consistent quality control in production and maintenance contexts. For precise workshop gauging, request the Metav IndustryLine gauge pin M323.572 via Metav Werkzeuge — Metav’s specialists in Emmerich can advise on fitment and delivery at info@metav-werkzeuge.com or +49 2822 7131930. Technical Data Article number: M323.572 GTIN: 4061905058431 Brand: Metav IndustryLine Facts Diameter: 5.72 mm Length: 50 mm Tolerance: ±0.001 mm Weight: 0.013 kg Special features Material: special steel Workshop execution Category: gauge pins Label: Prüfstift, einzeln, 5,72mm, +/- 0.001 mm Länge 50 mm Accuracy variation: ±0.001 FAQ What measurements is this pin intended for? The gauge pin is intended for end‑measurements, fit checks and seating verification where a defined reference diameter of 5.72 mm and tolerance of ±0.001 mm are required. Can the pin be used in fixture blocks or pin sets? Yes, the geometry and standardised diameter allow the pin to be used in pin blocks, seating fixtures and bespoke test rigs for repeatable inspection tasks. What advantages does the special steel construction offer? Special steel provides a balance of hardness and dimensional stability that helps maintain the reference diameter during repetitive use in workshop environments. Is this item part of a branded series? This is supplied under the Metav IndustryLine range and is identified as M323.572 for catalogue and inventory purposes. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
Fast, tactile checks where electronics are impractical
Gauges and test pins provide unequivocal go/no-go results for threads, bores, gaps and radii without relying on electronics. The range covers plug gauges and ring gauges for internal and external threads, feeler gauges and precision feeler strips for micro‑gap assessment, plus probe pins and measuring pins for tactile diameter and pitch checks.
How these tools work in the production environment
Mechanical gauges operate as direct reference standards: a plug gauge or ring gauge verifies conformity to thread profiles and mating ability, while limit gauges separate accept from reject in a single step. Test pins are used to tactilely measure small bore diameters, centre‑to‑centre distances and radii. Manufactured from hardened gauge steel or ceramic and often precision lapped, these instruments deliver immediate physical results that are ideal for incoming inspection, machine‑side checks and final control.
Measurable benefits that affect production performance
- Reduced scrap and rework through rapid, unambiguous pass/fail assessment.
- Increased repeatability thanks to very low measurement uncertainty and fine lapping.
- Lower downtime: quick checks at the machine save cycle time and reduce setup periods.
- Durable construction with high wear resistance from specialised, low‑distortion alloys.
- Versatile delivery formats: individual gauges, organised sets in wooden cases or metre‑length feeler rolls compliant with DIN 2269.
Why Metav is the practical choice for precision supplies
Metav combines decades of expertise with a broad warehouse and quality filtering from Emmerich. As a precision partner for industry, craft and trade, Metav supplies a comprehensive selection of gauges and test pins alongside complementary tools such as precision calipers and setting rings. With over 48,000 customers and a catalogue exceeding 250,000 items, Metav is positioned to supply reliably, reduce vendor complexity and support traceable quality control to national standards.
Summary
Gauges and test pins are indispensable for dependable, repeatable quality assurance where tactile, mechanical verification is preferred. Choose these plug gauges, ring gauges, feeler strips and probe pins when immediate, robust measurement decisions are required on the shop floor.
FAQ
What materials are gauges and test pins typically made from?
Gauges and test pins are usually manufactured from hardened gauge steel for durability and wear resistance; ceramic variants are available where thermal stability and minimal wear are critical.
How do thread gauges ensure mating capability?
Thread plug gauges and ring gauges check flank diameters and thread form against standards, providing a clear go/no‑go verdict that confirms pairability with mating parts.
Which tolerance class should I choose for probe pins and gauge sets?
Select tolerance classes aligned with your inspection requirements; for high‑precision tasks, sets produced to DIN 2269 or equivalent tolerance classes ensure micrometre‑level control and repeatability.
Can feeler gauges measure contact gaps in valve and engine work reliably?
Yes. Feeler gauges and precision feeler strips, supplied either as a fan or metre‑length rolls, allow accurate assessment of valve clearances and contact gaps down to micrometre increments.
How do limit gauges speed up in‑process inspection?
Limit gauges separate good from bad in a single, tactile operation, enabling rapid go/no‑go checks at the machine and reducing both inspection time and the likelihood of human interpretation errors.
Fragen zu diesen Produkten??
Mit mehr als 30 Jahren Erfahrung beraten wir Sie gerne persönlich.
Tel.: +49 2822 7131930
Mail: info@metav-werkzeuge.com