Precision gauge blocks and plug gauges for reliable dimensional control
Mechanical gauge blocks and plug gauges are essential for tactile verification of threads, bores and gap dimensions, providing fast, unambiguous go/no-go results that enhance process reliability and reduce scrap. Designed for industrial metalworking and toolmaking, these precision tools support incoming inspection and final quality checks by delivering traceable measurements in applications such as thread inspection, bore diameter testing and spacing checks. Manufactured from specially hardened, low-distortion alloys and fine-lapped for minimal measurement uncertainty, the range includes thread plug gauges, precision plug gauges and calibration gauge blocks to ensure long-term repeatability and wear resistance.
5.02mm Gauge Pin, ±0.001 mm, 50mm Length, Workshop Version - Metav IndustryLine
A high‑precision gauge pin that pairs compact dimensions with exceptional tolerance: 5.02 mm diameter and ±0.001 mm accuracy in a 50 mm length give reliable results for end‑measurements and fit checks. Combine repeatable metrology performance and robust workshop construction. Order the gauge pin M323.502 directly via Metav Werkzeuge or ask our consultants if needed. Gauge pin M323.502 — single precision pin, 5.02 mm diameter, ±0.001 mm tolerance (Metav IndustryLine) A gauge pin M323.502 engineered for precision end‑measurements and fit verification in workshop and quality control settings Workshop version construction Diameter 5.02 mm ±0.001 Length 50 mm for compact checks Special steel for long service life Accuracy where dimensional certainty counts The principal advantage of this tool is its precision: a nominal 5.02 mm diameter with a tight ±0.001 mm tolerance offers consistent results when assessing bore sizes, mating fits or end‑dimensions. Such a tolerance equates to micrometre‑level control, reducing uncertainty in pass/fail decisions and supporting reliable assembly checks. The compact 50 mm length keeps handling straightforward while maintaining the straightness and surface finish required for repeatable contact readings. Built for practical workshop use and durability Designed as a workshop version, the pin balances fine measuring ability with everyday robustness. Manufactured from special steel, the component resists wear in typical inspection routines and preserves the measuring face geometry under repeated use. The small mass and rigid profile facilitate rapid placement and withdrawal during batch inspections, while the corrosion‑resistant surface treatment improves longevity and reduces maintenance intervals, supporting uptime on the shop floor. Practical applications and measurement benefits This single gauge pin is intended for end measurements, quick fit checks, and verification of drilled bores or reamed holes in jigs and fixtures. Its nominal diameter and tolerance make it suitable as a reference probe for functional tests or for checking clearance and interference fits. When combined with calibrated ring gauges or fixture references, the pin improves the repeatability of pass/fail assessments and supports consistent quality control routines without introducing unnecessary handling complexity. Contact Metav Werkzeuge for specialist advice on integrating the M323.502 gauge pin into inspection workflows or for assistance selecting complementary gauges and calibration options Technical data SKU: M323.502 GTIN: 4061905059759 Brand: Metav IndustryLine Feature: Workshop version Diameter: 5.02 mm Tolerance: ±0.001 mm Length: 50 mm Weight: 0.011 kg Material: Special steel Typical use: End measurements and fit verification Design: Single gauge pin, precision ground Intended environment: Workshop and quality control FAQ What tolerance and diameter does this gauge pin provide? The gauge pin M323.502 from Metav IndustryLine is specified at 5.02 mm diameter with a tolerance of ±0.001 mm, suited to high‑precision fit checks. Can this pin be used for checking reamed bores and mating fits? Yes. The design and tolerance of the M323.502 make it appropriate for verifying reamed bores, mating fits and other end‑measurement tasks in workshop inspection routines. How should the pin be cared for to maintain accuracy? Store the pin in a clean, dry location and protect the measuring face from knocks and contamination. Light lubrication after cleaning will help preserve surface condition; avoid abrasive cleaning agents. Is the M323.502 suitable for repeated batch inspections? The workshop construction and special steel composition support repeated use in batch inspections while maintaining geometric stability and repeatability. Which accessories or complementary gauges work well with this pin? Use the M323.502 alongside calibrated ring gauges, gauge blocks or fixture plates to form reference assemblies for functional testing and comparative inspections. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
5.03mm Gauge Pin Single ±0.001mm Length 50mm, Workshop Version - Metav IndustryLine
Take advantage of workshop-grade repeatability and the narrow ±0.001 mm tolerance combined with a compact 50 mm length for reliable end‑measurement checks; supplied in a protective transport case for safe handling. Order the gauge pin directly via Metav Werkzeuge or consult our experts if additional information is required. M323.503 Gauge Pin – Metav IndustryLine, Ø 5.03 mm, ±0.001 mm The M323.503 gauge pin is a workshop‑grade precision pin designed for end‑measurement checks, assembly verification and press‑fit inspection tasks in production and quality control environments. Workshop‑grade accuracy ±0.001 mm Diameter 5.03 mm precision fit 50 mm special steel measuring shaft Supplied in protective transport case Consistent fit for tight tolerances A narrow tolerance of ±0.001 mm makes this gauge pin ideal where fit and clearance control are critical. The defined 5.03 mm diameter provides a repeatable reference for pass/fail checks and comparative measurements; this reduces setup iterations and supports stable process control. By using a single, traceable reference pin rather than repeated trial adjustments, downtime during inspection cycles is minimised. Built for repetitive workshop use and safe storage The 50 mm shaft uses special steel chosen for dimensional stability under routine handling, offering a balance between stiffness and compactness. The workshop variant is optimised for daily inspection tasks and is delivered in a protective transport case, which protects the pin from contamination and impacts during storage and transit. The small mass (approx. 0.011 kg) keeps handling simple and quick when multiple checks are required on the shop floor. Clear purpose and practical applications This precision pin serves as a straightforward end‑measure reference for bore validation, assembly control and final inspection steps. As a compact, single‑piece test pin it integrates easily into established inspection jigs and tactile gauges, supporting consistent go/no‑go decisions. The robust specification helps maintain process reliability and provides production teams with measurable evidence for quality documentation. For precise end‑measurement solutions from Metav IndustryLine, contact Metav Werkzeuge for availability, delivery options and technical advice at +49 2822 7131930 or info@metav-werkzeuge.com Technical Data Article number: M323.503 GTIN: 4061905059766 Manufacturer: Metav IndustryLine Category: Messstifte Facts Diameter: 5.03 mm Tolerance: ±0.001 mm Length: 50 mm Weight: 0.011 kg Special features Workshop execution Supplied in protective transport case Material: Special steel Story trigger: endmasse eClass: 21170231 FAQ What tolerance does this gauge pin offer? The M323.503 gauge pin is specified at ±0.001 mm, providing very fine repeatability for tight clearance checks. Which applications are suitable for this test pin? The pin is suitable for end‑measure checks, bore validation and assembly verification where a precise reference diameter is required. Is the pin supplied ready for safe transport and storage? Yes, the gauge pin is supplied in a protective transport case to prevent damage and contamination during handling. What material is used for the measuring shaft? The shaft is manufactured from special steel chosen for dimensional stability under routine workshop use. How is the product identified for ordering and inventory? The article is listed as M323.503 with GTIN 4061905059766 for clear identification. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
5.04mm Gauge Pin, Single, ±0.001mm, Length 50mm, Workshop Version - Metav IndustryLine
Take advantage of the combination of tight tolerance (±0.001 mm), special-steel construction and a compact 50 mm length for repeatable end-dimension checks in the workshop; order the gauge pin directly via Metav Werkzeuge or contact our technical advisers for application guidance. Gauge pin M323.504 — Single precision test pin, 5.04 mm diameter, ±0.001 mm The Gauge pin M323.504 is a single precision test pin intended for reliable inspection of bores and end dimensions in workshop and inspection settings. Single gauge pin 5.04 mm diameter Tolerance ±0.001 mm for tight fits 50 mm overall length for consistent probing Workshop version with robust finish Repeatable measurement accuracy for tight fits The compact test pin delivers repeatable accuracy thanks to a specified deviation of ±0.001 mm, which supports fine acceptance decisions and reduces costly rework. With a nominal diameter of 5.04 mm, the pin is suitable for end-dimension checks where small clearance variations matter; calibrated measuring chains and comparative gauges benefit from such small tolerances by providing consistent pass/fail results across batches. Robust design for everyday workshop use Designed as a workshop version, the pin is manufactured from special steel to withstand handling and routine use on the shop floor. The 50 mm length offers sufficient reach for common inspection tasks while keeping the component rigid during measurement. Delivered in a protective case for transport and storage, the test pin maintains its surface quality and geometric integrity between uses, which preserves measurement reliability and extends service life. Easy integration into inspection workflows The single-pin format is straightforward to incorporate into manual and fixture-based inspection processes. Its small mass and compact form make handling efficient in repetitive checks, speeding throughput without compromising precision. Using a defined test pin of known diameter simplifies traceability in production documentation and supports consistent assembly fits across production runs. Choose the Metav IndustryLine gauge pin M323.504 for secure end-dimension verification in workshop environments and contact Metav Werkzeuge for tailored application advice or ordering support at info@metav-werkzeuge.com or +49 2822 7131930 Technical Data Article number: M323.504 GTIN: 4061905059773 Manufacturer: Metav IndustryLine Facts Diameter: 5.04 mm Length: 50 mm Tolerance: ±0.001 mm Weight: 0.011 kg Special features Material: Special steel Workshop version Supplied in protective case FAQ What is the declared tolerance of this gauge pin? The M323.504 gauge pin is specified with a tolerance of ±0.001 mm, enabling tight acceptance criteria for precision inspections. For which inspection tasks is this test pin suitable? The single test pin is suitable for bore checks, end-dimension verification and comparative gauging in workshop and inspection environments where small diameter tolerances are critical. What material is the pin made from and how durable is it? The M323.504 is manufactured from special steel and produced as a workshop version, offering robust durability for routine use. What are the pin's dimensions and mass? Nominal diameter is 5.04 mm, overall length is 50 mm and the mass is approximately 0.011 kg. Is the pin supplied ready for transport and storage? The gauge pin is supplied in a protective case to preserve surface quality and geometry during transport and storage. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
5.05mm Test Pin, Single, ±0.001mm Accuracy, Length 50mm, Workshop Finish - Metav IndustryLine
Taking advantage of the combination of workshop‑grade robustness, ±0.001 mm accuracy and a compact 50 mm length ensures reliable end‑measure checks in daily inspection routines — order this precision gauge pin directly via Metav Werkzeuge or consult our specialists for application advice. Gauge pin, single — 5.05 mm, ±0.001 mm, 50 mm length (Metav IndustryLine) The gauge pin, single, 5.05 mm ±0.001 mm, 50 mm length is a compact, workshop‑grade reference pin for precise end‑measure and fit checks in inspection and fixture set‑up. Workshop version for robust use High tolerance: ±0.001 mm Diameter 5.05 mm, length 50 mm Delivered in transport case Reliable measurement where tight tolerances decide A compact gauge pin with a declared tolerance of ±0.001 mm provides a clear technical advantage where repeatable go/no‑go decisions are required. The extremely fine tolerance corresponds to high‑precision gauges used for end measurements and fits; in practice this reduces rework and speeds up pass/fail decisions on the shop floor. The stated accuracy should be interpreted as the manufacturing tolerance of the pin, ensuring it can serve as a stable reference for short‑range checks and comparative measurements. When paired with calibrated ring gauges or micrometres, the pin acts as a simple, direct measure for bore and hole verification. Durable design tailored to workshop routines Constructed from special steel, this workshop version is intended for regular handling and quick inspection cycles. The material choice balances hardness and wear resistance, so the gauge retains form over repeated seating and insertion operations. With a 50 mm overall length and a 5.05 mm diameter, the component is compact enough for bench use yet long enough to reach into slightly recessed features. Supplied in a transport case, the pin remains protected during storage and transit, reducing the risk of dings that would compromise measurement integrity. The modest mass contributes to easy handling during serial checks without introducing operator fatigue. Simple integration into quality control workflows As a single reference pin for end‑measure tasks, this item integrates directly into existing inspection routines and fixture checks. The product supports quick tactile verification and comparative gauging; technicians can use it to check bore fits, set gauges, or verify plug clearances. Describing the part as a precision reference helps planners decide its role: whether as a temporary go/no‑go aid, a setup reference in jigs, or a control artefact for routine dimensional checks. The compact format and workshop specification make it particularly suitable where a reliable, ruggedised pin is needed rather than delicate laboratory artefacts. For workshop‑grade inspection with ±0.001 mm tolerance, contact Metav Werkzeuge for purchasing and technical advice at info@metav-werkzeuge.com or +49 2822 7131930 Technical data Article number: M323.505 GTIN: 4061905057045 Label: Prüfstift, einzeln, 5,05mm, +/- 0.001 mm Länge 50 mm Facts Diameter: 5.05 mm Length: 50 mm Tolerance / accuracy: ±0.001 mm Weight: 0.011 kg Special features Material: special steel Workshop version Supplied in a transport case FAQ What is the intended use for this gauge pin? The gauge pin (single, 5.05 mm, ±0.001 mm, 50 mm length) is intended for end‑measure checks, bore verification and fixture set‑up in workshop inspection routines. Is the gauge pin suitable for regular shop‑floor use? Yes, the workshop version and special steel construction make this pin suitable for frequent handling and routine measurements on the shop floor. How is the gauge pin protected during storage and transport? The item is supplied in a transport case to protect the precision surface from damage during storage and transit. Can this pin be used as a reference for calibration chains? The pin serves as a stable reference for comparative checks and can be part of a calibration chain when used alongside calibrated ring gauges or micrometres. What product identifiers should be quoted when ordering? Please quote SKU M323.505 and GTIN 4061905057045 when enquiring or ordering this gauge pin. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
5.06mm Gauge Pin, ±0.001mm Accuracy, Length 50mm, Workshop Version, Special Steel - Metav IndustryLine
Take advantage of high repeatability and robust workshop design to streamline end‑measure inspections; the precise ±0.001 mm tolerance and compact dimensions ensure consistent fit‑up and reduced rework. Order the gauge pin directly via Metav Werkzeuge or ask our consultants for application advice. M323.506 Gauge Pin — 5.06 mm, ±0.001 mm, 50 mm (Metav IndustryLine) The M323.506 gauge pin is a workshop‑grade test pin designed for precise end‑measure checks and fixture set‑up in industrial metrology and quality control. Workshop-grade precision ±0.001 mm tolerance Diameter 5.06 mm for end-measure applications 50 mm length for fixture and gauge use Made from special steel for robust performance Repeatable accuracy for critical inspection tasks High‑precision inspection starts with reliable reference parts. The gauge pin offers a ±0.001 mm manufacturing tolerance on a nominal 5.06 mm diameter, which translates to tighter control of go/no‑go criteria and improved interchangeability in assemblies. In practice, this level of accuracy reduces sorting and rework rates because measured clearances and fits correspond closely to intended design values. The compact form and controlled geometry make the pin suitable for end‑measure applications and fine alignment tasks where positional certainty matters. Built for everyday workshop use and resilience Engineered as a workshop version, the pin balances dimensional control with mechanical resilience. The body is made of special steel, providing wear resistance under repeated seating and withdrawal in gauge fixtures. The 50 mm length offers a stable support surface for clamping and measurement while remaining easy to handle and store. Robust construction minimises the need for frequent replacement and supports sustained inspection cycles in production environments, contributing to lower total cost of ownership through longer in‑service life. Practical integration into inspection and fixture workflows The test pin is intended for end‑measure and alignment tasks within gauge blocks, fixtures and dedicated test rigs. Its consistent diameter and straightness make it suitable as a master datum for setting up jigs or for verifying bore sizes when used in combination with other reference gauges. Traceability is supported through the article identifiers and the clear specification of tolerance and dimensions, enabling integration into quality documentation and inspection plans. For routine quality control, the pin functions as a dependable reference that helps standardise measurement procedures across shifts and locations. Contact Metav Werkzeuge to discuss how the M323.506 gauge pin from Metav IndustryLine can be integrated into inspection routines or to request delivery from our Emmerich location. Technical data Article number: M323.506 GTIN: 4061905057250 Label: Prüfstift, einzeln, 5,06mm, +/- 0.001 mm Länge 50 mm Facts Diameter: 5.06 mm Tolerance: ±0.001 mm Length: 50 mm Weight: 0.011 kg Special features Material: Special steel Workshop version Application: end measurements FAQ What level of accuracy can be expected from this gauge pin? The M323.506 gauge pin from Metav IndustryLine is manufactured to a ±0.001 mm tolerance on the 5.06 mm diameter, providing high repeatability for end‑measure verification. Is the pin suitable for use in fixture alignment and gauge blocks? Yes, the 50 mm length and precise diameter make the pin suitable for fixture set‑up, alignment tasks and use as a reference in gauge block stacks or test rigs. What material is used and how does that affect durability? The pin is made from special steel, chosen for wear resistance and mechanical stability in workshop environments, which supports repeated seating without rapid degradation. Can this test pin be used in hardened or abrasive environments? The design is optimised for workshop use; for highly abrasive or specialised high‑temperature applications, material selection should be reviewed against the process conditions. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
5.07mm Gauge Pin, Single, ±0.001mm, 50mm Length, Workshop Version - Metav IndustryLine
Take advantage of the combination of ±0.001 mm repeatability, a compact Ø 5.07 mm diameter and a practical 50 mm length to ensure reliable end‑measure checks and fixture alignment. Order the gauge pin directly via Metav Werkzeuge or ask the consultants for application advice. Gauge Pin M323.507 — single inspection pin, Ø 5.07 mm, ±0.001 mm, length 50 mm (Metav IndustryLine) The Gauge Pin M323.507 is a workshop‑grade inspection pin designed for precise end‑measure verification and fixture alignment in metalworking and quality control operations. Workshop-grade precision pin Diameter Ø 5.07 mm ±0.001 mm Length 50 mm for in-depth checks Precise, repeatable checks for critical tolerances For tight tolerances and repeatable inspection routines the M323.507 offers an exceptional ±0.001 mm tolerance (equivalent to 1 µm) that supports high‑accuracy go/no‑go and end‑measure tasks. This level of precision minimises measurement uncertainty and reduces the risk of rework by providing a stable reference for pass/fail decisions. Using a dedicated inspection pin instead of makeshift gauges speeds up throughput and creates consistent results across inspection cycles, which is a tangible efficiency gain for production and QA teams. Robust construction suited to workshop use Built as a workshop‑grade tool from special steel, the pin combines dimensional stability with handling convenience. The 50 mm working length is long enough for many fixture and bore checks while remaining compact for easy positioning and storage. The lightweight 0.011 kg construction permits quick manual handling during repeated checks without compromising on rigidity. The simple, single‑piece design reduces sources of error and makes the pin suitable for routine inspection loops and alignment tasks in jigs and fixtures. Practical integration into inspection workflows Integration into inspection routines is straightforward: the pin serves as a reliable reference for end‑measure checks, alignment of mating parts and verification of drilled or bored holes. With a clearly defined Ø 5.07 mm diameter and traceable identifiers, the pin fits inspection lists and batch documentation. Its workshop specification supports frequent use in repair shops, toolrooms and production lines where durable, precise measuring aids are required. Relying on standardised gauge pins helps streamline documentation and supports process reproducibility across shifts. For workshop teams requiring sub‑micrometre repeatability, contact Metav Werkzeuge in Emmerich by phone +49 2822 7131930 or email info@metav-werkzeuge.com to discuss the Metav IndustryLine gauge pin and procurement options. Technical data SKU: M323.507 GTIN: 4061905057267 Product: Gauge pin, single, 5.07 mm, ±0.001 mm, length 50 mm Brand: Metav IndustryLine Facts Diameter: 5.07 mm Tolerance: ±0.001 mm Length: 50 mm Weight: 0.011 kg Special features Material: special steel Workshop‑grade execution Suitable for end‑measure checks and fixture alignment FAQ What tolerance does this gauge pin provide? The Metav IndustryLine gauge pin M323.507 provides a measuring tolerance of ±0.001 mm, suitable for high‑precision inspection tasks. Which material is the pin made from? This inspection pin is manufactured from special steel, specified for workshop durability and dimensional stability. For which applications is the pin recommended? The pin is intended for end‑measure verification, fixture alignment and go/no‑go checks in inspection and assembly processes. What are the exact dimensions of the pin? The pin has a diameter of 5.07 mm, a length of 50 mm and a mass of approximately 0.011 kg. Is the product traceable for inventory and documentation? Yes, the gauge pin is identifiable by SKU M323.507 and GTIN 4061905057267 for traceability in procurement and quality records. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
5.08mm Gauge Pin Length 50mm ±0.001mm Workshop Version - Metav IndustryLine
Take advantage of the tight manufacturing tolerance and robust workshop design for repeatable go/no‑go checks; the 5.08 mm diameter with ±0.001 mm accuracy and 50 mm length ensure reliable reference measurements. Order via Metav Werkzeuge or contact our consultants for assistance with application matching. Gauge pin M323.508 — test pin Ø 5.08 mm, ±0.001 mm (Metav IndustryLine) The gauge pin M323.508 is a single, workshop‑grade test pin designed for precise limit and reference measurements in inspection and assembly tasks Precision tolerance ±0.001 mm Diameter 5.08 mm ground to size Workshop‑grade special steel, 50 mm length Accurate reference for high‑confidence inspection The pin serves as a repeatable, hardened reference for plug‑gauge and clearance checks, offering a diameter of 5.08 mm with a verified ±0.001 mm tolerance. Such accuracy reduces measurement ambiguity in inspection routines and supports interchangeability checks during assembly. Ground and finished to size, the element functions as a straightforward verification tool for bore sizes and feature conformity, helping to reduce inspection time through a single, reliable measurement step. Robust construction built for the workshop Manufactured from special steel in a workshop‑grade execution, the test pin withstands typical handling and repeated seating in fixtures. With a length of 50 mm, it is long enough to stabilise insertion into bores while remaining compact for handheld checks. Supplied individually and protected in a transport case, the component arrives ready for immediate use and storage with reduced risk of surface damage. The robust material choice contributes to a consistent surface finish and wear resistance over many cycles. Practical integration into quality processes Designed for simple incorporation into inspection benches or portable kits, the component supports quick pass/fail assessments and correlates well with gauge blocks and master pins in a calibration chain. Traceability is facilitated via the product SKU M323.508 and GTIN for inventory control. The compact mass and clear specification simplify procurement and record keeping in quality documentation, while the workshop configuration ensures the pin is suited to day‑to‑day production environments rather than delicate lab conditions. Contact Metav Werkzeuge for tailored advice on integrating the M323.508 into inspection routines or for assistance in selecting matching gauge sets and storage solutions Technical Data Article number: M323.508 GTIN: 4061905058028 Label: Prüfstift, einzeln, 5,08mm, +/- 0.001 mm Länge 50 mm SKU: M323.508 Facts Diameter: 5.08 mm Tolerance: ±0.001 mm Length: 50 mm Weight: 0.011 kg Special features Material: special steel Workshop execution Supplied individually in a transport case Suitable for plug‑gauge and reference checks FAQ What diameter and tolerance does this gauge pin have? The gauge pin M323.508 is manufactured to a diameter of 5.08 mm with a tolerance of ±0.001 mm, making it suitable for precise limit and reference measurements. Is the test pin suitable for daily workshop use? Yes, the M323.508 is a workshop‑grade pin made from special steel and supplied in a protective transport case to withstand routine handling. Can this pin be used as a reference for bore inspections? The pin functions well as a reference for bore and clearance checks; its ground diameter and tight tolerance enable simple go/no‑go assessments and quick verification. How should the pin be stored to maintain accuracy? Keep the pin clean and dry in its transport case when not in use; this reduces surface contamination and preserves the finished diameter for reliable measurements. Does the product come with traceability data for inventory? The item is identifiable by SKU M323.508 and GTIN 4061905058028, which supports inventory control and traceability in quality records. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
5.09mm Gauge Pin, ±0.001 mm Accuracy, 50mm Length, Workshop Version - Metav IndustryLine
Take advantage of a workshop‑grade test pin that combines ±0.001 mm repeatability with a 5.09 mm nominal diameter and a 50 mm reach for reliable end‑measure checks. The robust special steel construction and protective transport case ensure repeatable inspection results and safe storage — order the part directly via Metav Werkzeuge or consult our specialists for specification support. M323.509 Test Pin (5.09 mm), ±0.001 mm, 50 mm – Metav IndustryLine The M323.509 Test Pin is a workshop‑grade gauging pin designed for high‑precision end‑measure verification and plug‑gauge replacement in production and inspection environments. Workshop‑grade special steel construction Diameter 5.09 mm with ±0.001 mm accuracy 50 mm overall length for extended reach Supplied in a protective transport case Consistent micrometre‑level repeatability for inspection The M323.509 is engineered to deliver ±0.001 mm repeatability, making it suitable where tight tolerances determine part acceptance. Such high resolution reduces false rejects and supports statistical process control by providing a stable reference for comparative measurements. Using a fixed‑diameter gauging element simplifies go/no‑go assessments and minimises measurement variability from operator handling, while the nominal 5.09 mm size matches common end‑measure requirements in small‑component inspection. Durable, workshop‑ready construction that keeps measuring reliable Built as a workshop‑grade tool from special steel, the pin resists everyday wear in inspection benches and toolrooms. The 50 mm overall length offers additional reach for recessed bores and stepped features while keeping handling straightforward. Supplied in a protective transport case, the component remains safe during storage and transit, supporting traceable inventory and lowering the risk of damage that would compromise dimensional integrity. Designed for efficient measurement workflows and stock management As a single replacement pin for gauging sets, this test pin streamlines maintenance of in‑line inspection equipment and keeps calibration cycles short. The compact weight (0.011 kg) and clear identification simplify stocking and handling in busy quality departments. The combination of precise geometry and straightforward form factor makes this gauging element a practical choice for both small series production and tool‑room tasks where repeatability and quick interchangeability are required. For specification advice, spare‑part supply or to include the M323.509 in an inspection kit, contact Metav Werkzeuge in Emmerich by email at info@metav-werkzeuge.com or by phone on +49 2822 7131930 for tailored support and prompt delivery. Technical data SKU: M323.509 GTIN: 4061905058035 Label: Prüfstift, einzeln, 5,09mm, +/- 0.001 mm Länge 50 mm Facts Diameter: 5.09 mm Tolerance: ±0.001 mm Length: 50 mm Weight: 0.011 kg Special features Material: special steel Workshop‑grade execution Supplied in protective transport case Single test pin for gauging and end‑measure checks FAQ What tolerances does this test pin achieve? The test pin achieves a dimensional tolerance of ±0.001 mm, which makes the M323.509 suitable for high‑precision comparison and plug‑gauge applications. Can the pin be used as a direct replacement in existing gauging sets? Yes. The single‑piece design and standard diameter allow the pin to serve as a direct replacement element in many gauging fixtures and inspection assemblies. What material is the pin made from and how does that affect wear? The component is made from special steel and provided in a workshop‑grade finish to withstand routine handling and preserve geometric stability during regular inspection use. Is the part traceable for inventory management? The item is supplied with a clear SKU (M323.509) and GTIN for straightforward identification and stock control within inspection departments. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
5.11mm Test Probe ±0.001 mm Length 50 mm Workshop Version - Metav IndustryLine
Take advantage of high-precision tolerance (±0.001 mm) together with a compact 5.11 mm diameter and a robust 50 mm length for dependable fit checks and end‑measurement tasks. Order the part directly via Metav Werkzeuge or contact the consultants for specification support. M323.511 gauge pin — 5.11 mm, ±0.001 mm precision (Metav IndustryLine) The M323.511 gauge pin is a single, workshop‑grade precision pin designed for tight fit verification and end‑measurements in inspection and assembly environments. High-precision tolerance ±0.001 mm Diameter 5.11 mm for tight fits Length 50 mm for versatile checks Workshop-grade special steel construction Reliable accuracy for critical fit checks A tolerance of ±0.001 mm positions this pin in the category of ultra‑fine inspection tools where dimensional certainty is essential. Such precision minimises measurement scatter during repeated checks and supports consistent go/no‑go assessments for mating parts. The tight specification also reduces rework by clarifying whether a bore or shaft meets its intended limits; when a numerical tolerance is this small, the measurement outcome becomes a reliable basis for production decisions. The construction and finish are optimised to preserve the diameter 5.11 mm under typical workshop handling. Durable design that suits everyday workshop use Manufactured from special steel, the component combines dimensional stability with wear resistance appropriate for repetitive contact checks. The 50 mm length offers a practical balance between reach and manoeuvrability, making the item simple to handle while retaining stiffness at the contact face. The workshop version is engineered for frequent use: surfaces are finished for low friction and the pin’s geometry supports repeatable seating in bores and mating features. This results in fewer measurement deviations caused by edge chatter or misalignment. Seamless integration into inspection processes As a single plug‑style pin for end‑measurements and fit verification, this item integrates cleanly into established quality control routines. It serves as a dependable reference for checking tolerances during in‑process inspection, final inspection and assembly validation. Traceable identifiers such as the GTIN aid inventory and document control in the lab or shop floor, while the compact form factor reduces handling time during batch sampling. For precision tasks that demand clear, numeric results, the pin provides an objective measurement vector that supports rational decision‑making in production workflows. Contact Metav Werkzeuge for tailored advice on integrating the M323.511 gauge pin into inspection routines and to request availability details via info@metav-werkzeuge.com or by phone on +49 2822 7131930 Technical data Article number: M323.511 GTIN: 4061905058059 Material: Spezial‑Stahl Accuracy: ±0.001 mm Diameter: 5.11 mm Length: 50 mm Weight: 0.011 kg Special version: Workshop execution Facts Diameter (mm): 5.11 Length (mm): 50 Tolerance (mm): ±0.001 Weight (kg): 0.011 ECLASS: 21170231 Special features Single gauge pin for end‑measurements Workshop‑grade construction GTIN assigned for traceability Compact format for quick handling Suitable for precise fit and bore checks FAQ What is the primary application of this gauge pin? The M323.511 gauge pin is intended for precise end‑measurements and fit verification of bores and mating features in inspection and assembly tasks. What tolerance and resolution does the pin offer? The pin is manufactured to an accuracy of ±0.001 mm, providing the tight dimensional control required for fine fit checks. Which material is used for the pin? The component is made from special steel, chosen for dimensional stability and resistance to wear in workshop use. Is the item suitable for repeated workshop checks? Yes. The workshop specification and robust finish support frequent handling and repetitive contact checks without rapid degradation of the contact surface. How is the product identified for inventory and traceability? Identification is supported by the article number M323.511 and the GTIN 4061905058059, facilitating stock control and documentation. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
5.12mm Gauge Pin, Single, ±0.001mm Accuracy, 50mm Length, Workshop Finish - Metav IndustryLine
High-precision end-dimension verification is achieved through the combination of ±0.001 mm tolerance and a hardened special steel body, plus a compact 50 mm length that aids handling and fixture access. Order the gauge pin directly via Metav Werkzeuge or consult our specialists for selection and delivery guidance. M323.512 — Gauge pin Ø 5.12 mm, ±0.001 mm (Metav IndustryLine) The M323.512 is a single, workshop‑grade gauge pin designed for end‑dimension inspection and precision go/no‑go checks in metrology and quality control. Workshop-grade precision pin Diameter 5.12 mm ±0.001 mm Length 50 mm, compact handling Consistent submicron accuracy for routine inspection A tolerance of ±0.001 mm places this gauge pin in the category of high‑precision inspection tools suitable for fine end‑dimension checks. The controlled diameter of 5.12 mm ensures repeatable seating in gauges and fixtures, which reduces measurement scatter and shortens decision cycles on the shop floor. Where traceable results are required, the pin’s specification supports documented quality checks and stable process control, improving the reliability of acceptance testing and reducing the need for rework. Robust workshop construction for enduring use Manufactured from special steel and finished for workshop environments, the pin balances hardness with surface quality to preserve the measuring diameter during repeated use. With a 50 mm overall length the design provides sufficient engagement while remaining easy to handle within fixtures or depth checks. The compact mass and workshop execution help resist everyday impacts and abrasion, delivering prolonged service life and consistent contact geometry for dependable measurements across shifts. Simple integration into calibration and control routines The gauge pin is a practical component for plug gauges, fixture setting and final inspection steps within production control. Its compact dimensions and precise tolerance make it suitable for alignment, end‑dimension verification and reference checks. Labelling with SKU and GTIN enables transparent inventory control and traceability in calibration records; the clear technical specification speeds up procurement and replacement, keeping inspection cycles uninterrupted and quality documentation coherent. For technical advice or to secure supply of this Metav IndustryLine gauge pin, contact Metav Werkzeuge GmbH in Emmerich — call +49 2822 7131930 or email info@metav-werkzeuge.com for guided selection and prompt delivery. Technical Data Article number: M323.512 GTIN: 4061905058066 Category: Gauge pins Facts Diameter: 5.12 mm Tolerance: ±0.001 mm Length: 50 mm Weight: 0.011 kg Special features Material: Special steel Version: Workshop execution Label: Prüfstift, single item FAQ What tolerance does this gauge pin offer? The gauge pin is specified with a ±0.001 mm tolerance, making the M323.512 suitable for high‑precision end‑dimension checks where tight dimensional control is required. Is the material suitable for repeated shop use? Yes. The M323.512 is made from special steel and configured as a workshop execution to withstand regular handling and maintain diameter integrity during routine inspection tasks. How is the gauge pin identified for inventory and calibration? Identification is provided via the SKU M323.512 and GTIN 4061905058066, which support straightforward tracking in calibration records and procurement systems. Can this pin be used in standard plug gauges and fixtures? The compact 50 mm length and precise 5.12 mm diameter make the pin well suited for use in plug gauges, fixture setting and end‑dimension verification in both workshop and inspection environments. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
5.13mm Gauge Pin Single ±0.001mm Length 50mm Workshop Version - Metav IndustryLine
The combination of ±0.001 mm accuracy, a compact 5.13 mm diameter and a robust 50 mm length delivers micrometric repeatability for routine hole gauging; the workshop‑grade construction keeps handling simple and durable. Order directly via Metav Werkzeuge or consult the technical team for application advice. Gauge pin M323.513 — single inspection pin, 5.13 mm diameter, ±0.001 mm (Metav IndustryLine) The gauge pin M323.513 is a single, precision inspection pin designed for end‑measurement and hole verification in workshop and quality‑control settings. Workshop version, robust design Diameter 5.13 mm with ±0.001 mm accuracy Length 50 mm, precision ground Made from special steel Supplied in transport case Secure process control through micrometric accuracy A tolerance of ±0.001 mm positions this pin in the micro‑accuracy class, suitable where tight fits and clearances are critical. The fine tolerance reduces uncertainty in pass/fail decisions during hole inspection and prevents unnecessary rework; this translates directly into fewer scrapped parts and more consistent lot quality. The small diameter of 5.13 mm makes the pin ideal for verifying bores and plug gauges where sub‑micron deviations would otherwise pass undetected. Using a precision‑ground inspection pin in the measuring chain improves statistical control and contributes to traceable, repeatable measurements. Workshop‑ready design that withstands handling Built as a workshop version, the pin combines a compact 50 mm length with robust surface treatment from special steel, helping it resist routine wear and maintain concentricity under repeated use. The shorter length aids handling and reduces lever‑induced bending during insertion and removal, improving measurement stability in busy production environments. Supplied in a secure transport case, the pin arrives ready for immediate use and safe storage between measurements, reducing downtime and protecting the calibrated geometry during transfer between measurement stations. Practical integration into inspection workflows The pin is intended for straightforward integration into existing gauging procedures: use as a reference plug for bore checks, in fixture verification or as a comparator within dimensional test benches. Its traceable accuracy supports documentation of measurement processes and helps maintain quality records. The compact geometry and workshop orientation make the pin suitable for fast, repetitive checks on the shop floor, enhancing throughput without sacrificing precision. Identification via GTIN 4061905058981 simplifies inventory management and procurement for spare‑part cycles. For reliable hole gauging and consistent workshop measurement, choose the Metav IndustryLine gauge pin M323.513 — contact Metav Werkzeuge for supply options and application guidance at info@metav-werkzeuge.com or by phone on +49 2822 7131930 Technical data Article number: M323.513 GTIN: 4061905058981 Description: Gauge pin, single, 5.13 mm, ±0.001 mm, length 50 mm Facts Diameter: 5.13 mm Tolerance: ±0.001 mm Length: 50 mm Weight: 0.011 kg Measuring range: 5.13 mm Special features Material: special steel Workshop execution Supplied in transport case Precision ground surface FAQ What level of tolerance does the pin provide? The gauge pin M323.513 provides a tolerance of ±0.001 mm, enabling micrometric verification of hole diameters and tight fits. Which tasks is this pin intended for? The pin is designed for end‑measurement, bore checking and fixture verification in workshop and quality‑control workflows where compact, high‑precision gauges are required. Is the pin supplied ready for transport and storage? Yes, the item is supplied in a transport case to protect the geometry during shipment and while moving between workstations. What material is used for the pin? The pin is manufactured from special steel, chosen for dimensional stability and wear resistance in routine inspection use. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
5.14mm Gauge Pin, Single, ±0.001mm, Length 50mm, Workshop Version - Metav IndustryLine
Take advantage of ±0.001 mm tolerance and a compact 50 mm length for reliable end‑dimension checks; the workshop‑grade construction and protective transport case keep inspection workflows efficient and reproducible. Order the gauge pin directly via Metav Werkzeuge or contact our consultants for application advice. M323.514 gauge pin – 5.14 mm, ±0.001 mm accuracy (Metav IndustryLine) A M323.514 gauge pin designed for precise end‑dimension verification and tight clearance checks in workshop inspection and production environments. Workshop version, robust construction Diameter 5.14 mm with ±0.001 mm tolerance Length 50 mm for standard inspection tasks Supplied in protective transport case Accurate, repeatable checking for routine inspection The compact inspection pin delivers high‑precision dimensional verification where small clearances matter. With a diameter of 5.14 mm and a tolerance of ±0.001 mm, the pin supports fine acceptance testing and go/no‑go checks that reduce rework and production downtime. The tight tolerance is beneficial when verifying end faces, bore fits or mating parts that require consistent repeatability; the hard material and ground finish minimise wear and preserve measurement integrity over repeated cycles. This performance is presented in a workshop‑oriented format that integrates easily into standard metrology procedures. Built for workshop handling and durability Constructed from special steel and offered in a workshop execution, the inspection pin balances corrosion resistance with wear performance for routine use. The 50 mm length provides enough engagement for most plug and clearance checks while remaining easy to handle and less prone to flex during measurement. Supplied in a protective transport case, the pin is ready for storage and safe transfer between bench and machine, reducing the risk of damage during daily handling and preserving the ground measuring surface for longer service life. Practical integration into quality workflows The product is a straightforward solution for end‑dimension controls, gauge blocks, and fixture checks within production and inspection areas. Its compact geometry makes it a convenient reference tool at assembly stations and in small inspection benches. As a single gauge pin, it complements sets of plug gauges or pin assortments and can be used to confirm bore sizes, fitment clearances or as a master reference for portable comparators. The robust specification and clear labelling ensure traceability in routine quality documentation and support process stability across shifts. Discuss suitability with Metav Werkzeuge for precise application matching and supply options directly from Emmerich, where practical expertise supports every purchase Technical data Article number: M323.514 SKU: M323.514 GTIN: 4061905058998 Manufacturer: Metav IndustryLine Weight: 0.011 kg Diameter: 5.14 mm Tolerance: ±0.001 mm Length: 50 mm Material: Special steel Label: Prüfstift, einzeln, 5,14mm, +/- 0.001 mm Länge 50 mm Facts Category: Gauge pin / inspection pin Intended use: End‑dimension and clearance checks Workshop version: yes Special features Workshop execution Protective transport case supplied Ground diameter for repeatable contact FAQ What inspection tasks is the M323.514 gauge pin suited for? The M323.514 gauge pin (Metav IndustryLine) is designed for end‑dimension verification, bore clearance checks and routine go/no‑go comparisons in workshop and production inspections. Is the tolerance of ±0.001 mm sufficient for precision assembly checks? Yes, the ±0.001 mm tolerance of the M323.514 gauge pin meets tight clearance and fitment requirements commonly found in precision assembly and small‑part inspection. What material is used and how does it affect wear resistance? The pin is made of special steel, chosen to provide durable wear resistance and a stable ground surface that maintains dimensional integrity over repeated use. Can the gauge pin be used with fixture gauges and comparator setups? The single gauge pin is suitable as a reference check within fixture gauges and comparator setups and complements existing plug‑gauge assortments for quick verification. Does the product include protective packaging for transport? Yes, the inspection pin is supplied in a protective transport case to reduce the risk of damage during handling and transfer between workstations. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
5.15mm Gauge Pin Single ±0.001mm 50mm Length Workshop Finish - Metav IndustryLine
Benefit from workshop-grade precision and a ±0.001 mm tolerance combined with a compact 50 mm length for reliable end‑measure checks; order the gauge directly via Metav Werkzeuge or consult our specialists for application advice. Gauge pin M323.515 – Single gauge pin, 5.15 mm, ±0.001 mm (Metav IndustryLine) The gauge pin M323.515 is a single, precision ground test pin for high‑resolution dimensional checks and end‑measure verification in workshop and inspection environments Single gauge pin Ø 5.15 mm, tolerance ±0.001 mm Precision ground special steel construction Length 50 mm for compact inspection tasks Delivered in a protective transport case Repeatable measurements with micrometric tolerance The design delivers consistent repeatability through a declared tolerance of ±0.001 mm, equivalent to 1 µm, which significantly reduces measurement uncertainty in routine checks. Such precision supports tighter process control and lowers the risk of rework by providing a clear, measurable reference for bore and pin gauges. The nominal diameter of 5.15 mm is suited to fine dimensional checks where sub‑micron deviation would otherwise compromise assembly fits; the result is a measurable efficiency gain during incoming inspection and final quality release. Robust workshop design for everyday handling Manufactured in special steel, the pin balances surface hardness and resistance to wear while keeping a compact overall length of 50 mm and a low mass (approx. 0.011 kg), making it easy to handle during repetitive tasks. The workshop version is optimised for practical use: its finish ensures reliable seating in fixtures and jigs, and it resists typical shopfloor contaminants better than untreated pins. Delivery in a protective transport case preserves the ground surfaces during storage and transit, maintaining traceability and usability across multiple shifts. Integrates into inspection workflows and traceability systems The single test pin is ready for direct use as a reference element in go/no‑go checks, fixture setting or as a measuring master for optical comparators and plug gauges. Labelling with SKU M323.515 and GTIN ensures straightforward inventory management and procurement. Where documentation and calibration chains are required, the pin can be incorporated into existing inspection routines without the need for special adaptors, supporting faster changeovers and clearer audit trails across production and quality departments. For workshop applications requiring micrometric repeatability, choose the Metav IndustryLine gauge pin and contact Metav Werkzeuge in Emmerich for tailored technical guidance at info@metav-werkzeuge.com or +49 2822 7131930 Technical Data Article number: M323.515 GTIN: 4061905059001 Brand: Metav IndustryLine Material: Special steel Facts Nominal diameter: 5.15 mm Tolerance: ±0.001 mm Length: 50 mm Weight: 0.011 kg Eclass: 21170231 Special features Workshop version Precision ground surface Protective transport case included Intended for end‑measure and reference checks Single pin delivery format FAQ What is the declared tolerance of this gauge pin? The declared tolerance is ±0.001 mm, which corresponds to 1 µm and is specified for the gauge pin M323.515 from Metav IndustryLine. Is the material suitable for regular shop use? Yes, the pin is made from special steel and the workshop version is designed for regular handling and resistance to typical workshop wear. Does the delivery include protective packaging? A protective transport case is included with the product to preserve the ground surface during storage and transport. Can this pin be used as a master for fixture setup? The pin is suitable as a reference master in fixture setting and go/no‑go checks; its compact 50 mm length fits many standard jigs. Is the gauge pin supplied calibrated? Calibration is not indicated by the product label; if a calibrated certificate is required, please query Metav Werkzeuge for available calibration options for M323.515. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
5.16mm Test Pin ±0.001 mm Length 50 mm, Workshop Version - Metav IndustryLine
Take advantage of high‑precision measurement with a workshop‑grade gauge pin that combines repeatable tolerance, compact handling and robust construction; order directly via Metav Werkzeuge or consult our specialists for application advice. M323.516 Gauge Pin — 5.16 mm, ±0.001 mm, 50 mm length (Metav IndustryLine) The M323.516 is a workshop‑grade gauge pin designed for precise end‑measure checks and reference fits in metrology and quality control applications. Workshop-grade finish Diameter 5.16 mm ±0.001 mm tolerance Length 50 mm for end measurement Supplied in protective transport box Precision that supports reproducible inspection results The compact cylindrical gauge is manufactured for high repeatability, offering a nominal diameter of 5.16 mm with an inspection tolerance of ±0.001 mm, which makes it suitable where minimal clearance and tight fits determine part acceptance. The very small tolerance reduces measurement variation and supports faster decision making in control loops, so batch acceptance and first‑article checks run with fewer re‑measurements and lower scrap rates. The precision is conveyed through measurable figures rather than marketing claims, enabling planners to compare directly against inspection requirements. Robust workshop design for everyday use Built as a workshop‑grade tool from special steel, the pin resists wear while remaining easy to handle on the shop floor. At a length of 50 mm the pin offers sufficient engagement for end‑measure and reference tasks without compromising rigidity; its low mass aids quick placement in fixtures and gauges. Delivery in a protective transport box preserves the measuring face and overall geometry during storage and transit, supporting long‑term dimensional stability and reducing the need for premature replacement. Seamless integration into inspection processes Marked for traceable identification (GTIN available) and referenced under SKU M323.516, this gauge pin is intended as a reference element for go/no‑go checks, alignment aids and verification of bore sizes where a narrow tolerance band is required. The small form factor and light weight (approx. 0.011 kg) simplify placement in jigs or modular fixturing while the narrow tolerance improves interchangeability between mating components. The technical specification focuses on measurable benefits: reproducible fits, reduced cycle time for quality checks and reliable reference behaviour in production measurement routines. Contact Metav Werkzeuge today to discuss suitability for specific inspection tasks or to request ordering options for the M323.516 gauge pin from the Metav IndustryLine range Technical Data Article number: M323.516 GTIN: 4061905059018 SKU: M323.516 Facts Diameter: 5.16 mm Tolerance: ±0.001 mm Length: 50 mm Weight: 0.011 kg Special features Workshop‑grade execution Material: Special steel Supplied in protective transport box FAQ What level of tolerance does this gauge pin offer? The M323.516 gauge pin (Metav IndustryLine) is specified with a tolerance of ±0.001 mm for consistent end‑measure references. Which material is used for the gauge pin? This gauge pin is made from special steel, giving it wear resistance suitable for workshop use and repeated seating in fixtures. Is the pin suitable for go/no‑go checks and alignment tasks? Yes, the geometry and tight tolerance of the M323.516 make it appropriate for go/no‑go checks, alignment aids and reference fits in inspection fixtures. How is the pin delivered for transport and storage? The gauge pin is supplied in a protective transport box to preserve the measuring faces and maintain geometry during storage and transit. Can this pin be used with common gauge blocks and fixtures? The pin’s nominal diameter and precision make it compatible with standard small‑bore fixtures and modular gauge setups that require a tight reference diameter. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
5.17mm Test Pin ±0.001 mm Length 50 mm Workshop Version - Metav IndustryLine
Choose the combination of ±0.001 mm accuracy, 5.17 mm diameter and a 50 mm length for reliable end‑measurement in production and inspection; the workshop version arrives protected in a transport box for secure handling. Order the gauge pin M323.517 directly via Metav Werkzeuge or ask our consultants if needed. Gauge pin M323.517 — test pin, 5.17 mm ±0.001 mm, workshop version (Metav IndustryLine) A gauge pin tailored for precise end‑measurements and bore verification in workshop and inspection environments, providing micron‑level tolerance in a compact 50 mm length. High-precision ±0.001 mm tolerance Diameter 5.17 mm for tight fits 50 mm overall length for deeper bores Workshop version supplied in transport box Precision that reduces rework and inspection time The exceptionally tight ±0.001 mm tolerance (one micrometre) ensures consistent results when checking final bore diameters and plug fits; this level of repeatability lowers the likelihood of rework and rejects. Using a dedicated solid test pin simplifies pass/fail decisions during routine checks and speeds up handling compared with adjustable gauges. The compact diameter and precise manufacturing make the component particularly suitable for end‑of‑line verification where repeatable single‑point measurements are required. Built for workshop durability and safe transport Constructed from special steel and specified as a workshop version, the pin balances wear resistance with dimensional stability for frequent use on the shop floor. The 50 mm overall length offers access into deeper bores while maintaining stiffness, and the part is supplied in a transport box to protect the measuring surface during storage and transit. These choices reduce downtime and protect the measuring geometry, which helps maintain measurement integrity across regular workflows. Simple integration into inspection and fixture setups The pin is designed as a straightforward reference element for manual checks, fixture setting and comparative gauging in quality control routines. Marked by SKU M323.517 and identifiable via GTIN, it fits common measurement jigs and can serve as a reliable datum when aligning components for assembly or test. For bespoke metrology needs or advice on fitting the pin into existing inspection sequences, technical guidance is available from the supplier to ensure the component performs as intended. For tailored advice and supply of the Metav IndustryLine gauge pin M323.517, contact Metav Werkzeuge in Emmerich at info@metav-werkzeuge.com or call +49 2822 7131930 Technical data SKU: M323.517 GTIN: 4061905059025 Material: Special steel Designation: Workshop version Core dimensions Diameter: 5.17 mm Length: 50 mm Tolerance: ±0.001 mm Weight: 0.011 kg Special features Delivery in transport box (plastic or wooden) for safe transport Category: Gauge pins / Messstifte ECLASS: 21170231 Application trigger: end measurement FAQ What tolerance does this gauge pin offer? The gauge pin M323.517 is manufactured to a tolerance of ±0.001 mm, enabling micron‑level checks for final bore verification. What are the diameter and length of the pin? Diameter is 5.17 mm and overall length is 50 mm, dimensions suitable for deeper bore inspections and fixture use. Is the pin suitable for workshop use and transport? Yes — the M323.517 is the workshop version and is supplied in a transport box designed to protect the measuring surface during handling and transit. Which material is the pin made from? The pin is made from special steel, selected for dimensional stability and wear resistance in regular inspection tasks. How is the part identified for procurement or inventory? The component is listed under SKU M323.517 and GTIN 4061905059025 for clear identification in ordering and stock systems. Metav IndustryLine: Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
5.18mm Gauge Pin, Single, ±0.001mm Accuracy, Length 50mm, Workshop Version - Metav IndustryLine
Take advantage of the exact ±0.001 mm tolerance and compact 5.18 mm diameter for reliable end‑measure checks; robust workshop design and delivery in a protective transport case make this an efficient option for repetitive quality control — order via Metav Werkzeuge or consult our specialists for integration advice. Gauge pin M323.518 — 5.18 mm diameter, ±0.001 mm accuracy (Metav IndustryLine) A Gauge pin M323.518 designed as a single test pin for precise diameter verification and end‑measure inspection in workshop and production environments Workshop design for daily use Diameter 5.18 mm with ±0.001 mm accuracy Hardened special steel for long wear resistance Delivered in a protective transport case Consistent measurement accuracy for fewer rejects The M323.518 test pin delivers a ±0.001 mm tolerance that supports tight production tolerances and consistent pass/fail decisions. Specified as a single gauge pin with a nominal 5.18 mm diameter, it is suited to high‑accuracy checks where a clear numerical boundary prevents ambiguity. By reducing measurement scatter, the pin helps to lower scrap rates and shortens inspection cycles, offering a measurable contribution to throughput and process stability. Built for the workshop: robust, compact and easy to handle Manufactured from special steel and finished for workshop use, this compact probe combines durability with straightforward handling. The 50 mm length gives enough engagement for reliable seating while remaining compact for confined fixtures and hand inspection. Its low mass (approx. 0.011 kg) minimises deflection during insertion, and the hardy construction resists everyday wear — advantages that translate into reduced replacement frequency and predictable tool life. Practical application: end‑measure checking and inline control Intended for end‑measure and small‑bore verification, the pin functions well in both manual bench checks and semi‑automated inspection jigs. Supplied as a single unit, the component is ideal for sampling, reference checks and comparator setups where a defined reference diameter is required. The workshop format and protective transport case ensure the geometry arrives undamaged and remains ready for immediate use, supporting fast deployment in production or test benches. For supply and tailored advice on Metav IndustryLine gauge pins, contact Metav Werkzeuge in Emmerich by e‑mail at info@metav-werkzeuge.com or by phone on +49 2822 7131930 for reliable delivery and integration support Technical Data Article number / SKU: M323.518 GTIN: 4061905059032 Brand: Metav IndustryLine Description: Single gauge pin, 5.18 mm nominal diameter Numbers / Core technical data Diameter: 5.18 mm Length: 50 mm Accuracy / Tolerance: ±0.001 mm Weight: 0.011 kg Special features Material: special steel Design: workshop execution Delivery: single pin in protective transport case Application: end‑measure checks and small‑bore verification FAQ What tolerance does the gauge pin offer? The M323.518 gauge pin is specified with a tolerance of ±0.001 mm, making it suitable for tight tolerance end‑measure and diameter checks. Which material is used for this test pin? The pin is made from special steel and finished for workshop use to provide wear resistance and long service life. How is the pin delivered to ensure protection? The gauge pin M323.518 is supplied as a single unit in a protective transport case to prevent damage during shipment and storage. Can this pin be used for inline inspection jigs? Yes, the compact 50 mm length and workshop design make the pin suitable for both bench tests and semi‑automated inspection fixtures. Is the M323.518 suitable for precision sampling in production? The tight tolerance and robust construction of this Metav IndustryLine gauge pin make it an appropriate choice for repeat sampling and production control. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
5.19mm Test Pin ±0.001mm Length 50mm Workshop Version - Metav IndustryLine
Take advantage of a compact test pin that pairs ultra‑fine tolerance with robust workshop construction; the combination of ±0.001 mm accuracy and a nominal diameter of 5.19 mm ensures reproducible end‑measure checks and precise locating. Order the component directly via Metav Werkzeuge or consult our specialists for specification support. M323.519 gauge pin (5.19 mm, ±0.001 mm) — Metav IndustryLine A M323.519 gauge pin engineered for high‑precision end‑measure verification and stable locating tasks in workshop metrology. Workshop grade test pin, precision ±0.001 mm Diameter 5.19 mm for nominal end‑measure checks Length 50 mm for stable locating and insertion Made from special steel for wear resistance Dependable accuracy for critical measurements The gauge pin delivers ±0.001 mm tolerance in a compact format, reducing measurement uncertainty where tight limits matter. This level of precision supports consistent go/no‑go assessments and helps to prevent assembly errors that lead to rework. Because the component is manufactured as a single turned pin with a smooth running surface, wear is minimised and repeatability is improved — a rational investment that lowers process variation and protects downstream quality control. Robust construction tailored for workshop use Constructed from special steel and specified as a workshop variant, the test pin combines surface durability with dimensional stability under normal handling. The 50 mm length offers sufficient engagement for typical locating and end‑measure checks while keeping the mass low for ease of handling; the part weighs approximately 0.011 kg, which aids rapid placement and extraction. These design choices balance longevity with the convenience required on production benches and in toolrooms. Practical applications and integration into inspection routines Designed for routine end‑measure verification, bore plugging and alignment tasks, the pin adapts to slot, bore and fixture checks where a precise nominal gauge is required. The 5.19 mm diameter is suitable for nominal inspection tasks and comparative checking, and the smooth, turned finish reduces the risk of surface marking on delicate parts. In metrology workflows this component functions as a reliable reference element for dimensional checks and quick go/no‑go validation within assembly and inspection stations. Specify the Metav IndustryLine M323.519 gauge pin for reliable end‑measure checks and contact Metav Werkzeuge in Emmerich for tailored advice at info@metav-werkzeuge.com or +49 2822 7131930 Product data SKU: M323.519 GTIN: 4061905059049 Brand: Metav IndustryLine Facts Diameter: 5.19 mm Tolerance: ±0.001 mm Length: 50 mm Weight: 0.011 kg eClass: 21170231 Special features Material: special steel Design: workshop execution Application: end‑measure verification, locating, go/no‑go checks FAQ What does the tolerance ±0.001 mm indicate for this gauge pin? The tolerance ±0.001 mm denotes the manufacturing accuracy of the M323.519 gauge pin; it specifies the maximum permissible deviation from the nominal diameter, ensuring highly repeatable measuring and go/no‑go decisions. Which applications suit the M323.519 gauge pin best? The M323.519 gauge pin (Metav IndustryLine) is intended for end‑measure checks, bore plugging and locating tasks in workshop and toolroom inspection routines where a precise nominal reference is required. What is the construction material and why does it matter? Made from special steel, the M323.519 offers enhanced wear resistance and surface stability, which prolongs service life and maintains dimensional integrity during repetitive use. Can the pin be used for delicate components without marking them? Yes, the turned and smoothed finish of the M323.519 gauge pin reduces surface contact stress and the risk of marking when used for standard insertion and alignment operations. Are there dimensional data available for integration into inspection plans? Dimensional data for the M323.519 are provided in the technical section above (diameter 5.19 mm, tolerance ±0.001 mm, length 50 mm, weight 0.011 kg) for direct incorporation into inspection documentation and process sheets. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
5.1mm Gauge Pin, Single, ±0.001mm Accuracy, 50mm Length, Workshop Version - Metav IndustryLine
Combine workshop-grade durability with ultra-fine tolerance to achieve reliable end-measure checks: ±0.001 mm accuracy, 5.10 mm diameter and a compact 50 mm length make this gauge pin ideal for production and inspection tasks. Order the gauge pin directly via Metav Werkzeuge or contact our consultants if required. M323.510 — Gauge pin, 5.10 mm, ±0.001 mm (Metav IndustryLine) The M323.510 is a workshop-grade gauge pin designed for precise end-measure checks and fit verification in production and inspection environments. Workshop-grade precision ±0.001 mm Diameter 5.10 mm, tight tolerance Special steel construction for longevity Length 50 mm for end-measure checks Consistent tolerance for decisive go/no-go checks The defining characteristic is the ±0.001 mm tolerance, which provides a clear rational advantage when distinguishing acceptable fits from rejects. A tolerance at the micrometre level reduces ambiguity in pass/fail decisions and shortens inspection cycles, because measurements become directly comparable across shifts and machines. This level of control suits inline quality gates, assembly checks and calibrated reference tasks where repeatability matters. Compact design built for everyday workshop use Crafted as a workshop‑grade component, the pin combines a special steel construction with a compact 50 mm length to balance handling and durability. The short length assists in stable seating during end-measurements and minimises deflection, which is crucial when assessing tight fits or small bores. With a nominal diameter of 5.10 mm, the pin is easy to position and quick to swap during serial checks, supporting efficient measurement workflows without sacrificing longevity. Traceable identification and straightforward integration Identification and logistics are simplified by clear product identifiers: SKU M323.510 and GTIN 4061905058042. The single-pin format suits use as a reference plug, a calibration aid for gauges or as a precision test mandrel in fixture set-up. Supplied by Metav IndustryLine and distributed through Metav Werkzeuge, the component arrives ready for immediate use in standard inspection routines and pairs easily with micrometres, dial gauges and other bench metrology tools. Contact Metav Werkzeuge to discuss how the M323.510 gauge pin fits into existing inspection routines or to arrange supply; phone +49 2822 7131930 or email info@metav-werkzeuge.com Technical Data Article number: M323.510 GTIN: 4061905058042 Brand: Metav IndustryLine Description: Gauge pin, single, ø 5.10 mm, ±0.001 mm, length 50 mm Facts Diameter: 5.10 mm Length: 50 mm Tolerance: ±0.001 mm Weight: 0.011 kg Special features Material: Special steel Workshop version ECLASS: 21170231 Single item for end-measure checks FAQ What tolerance does this gauge pin provide? The M323.510 gauge pin from Metav IndustryLine is specified with a tolerance of ±0.001 mm, making it suitable for micrometric pass/fail and fit inspections. In which tasks is this pin typically used? This precision pin is designed for end-measure checks, fit verification and as a reference mandrel during fixture set‑up in production and inspection environments. What material is the pin made from? The M323.510 is produced from special steel and finished for workshop use to offer a durable contact surface for repeated measurements. How is the product identified for inventory and traceability? Identification is provided by SKU M323.510 and GTIN 4061905058042, allowing straightforward stock management and traceability within inspection workflows. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
5.21mm Precision Gauge Pin ±0.001mm Length 50mm Workshop Version - Metav IndustryLine
Take advantage of the combination of industrial-grade accuracy, compact dimensions and workshop-ready design for reliable in-process checks and fixture validation. Order the item directly via Metav Werkzeuge or consult our technical team for application advice. Gauge pin M323.521 — precision test pin, 5.21 mm diameter, ±0.001 mm tolerance (Metav IndustryLine) The Gauge pin M323.521 is a single precision test pin designed for high-accuracy reference and go/no-go checks in inspection fixtures and jigs. ±0.001 mm tolerance Diameter 5.21 mm Length 50 mm Special steel construction Precision that keeps production on target This compact test pin offers a tolerance of ±0.001 mm, which makes it suitable for demanding dimensional checks where small deviations matter. The declared 5.21 mm diameter and 50 mm length provide a stable datum for plug gauges, alignment pins and go/no-go fixtures; the combination of these dimensions reduces positional play during repeated insertions. By using a hardened, dimension-stable reference element, measurement uncertainty is limited and inspection throughput improves — a clear rational benefit for batch control and first-article inspections. Robust workshop design for repeated handling Made from special steel, the component is engineered for repetitive use in workshop environments. The workshop version indicates a focus on durability and straightforward handling: short mass reduces wear on mating bores and the compact weight (approx. 0.011 kg) simplifies manual placement. The single-item supply format suits operators who need a specific diameter for setup or replacement without buying sets. This robustness lowers the risk of downtime and conveys confidence that the reference pin will resist deformation under normal workshop conditions. Practical advantages in fixture building and inspection As a precision reference element, the pin serves both as a locating device and a control gauge. Its narrow tolerance supports precise alignment of small-bore components and repeatable seating in jigs, which in turn shortens setup time and reduces scrap rates. The clear numeric specification and traceable SKU make inventory and traceability simple to manage in toolrooms and quality labs. For engineers who demand predictable behaviour from their reference parts, the measurable specification of this test pin translates directly into fewer calls for adjustment and more consistent production results. For precise workshop calibration and reliable fixture references, contact Metav Werkzeuge about the M323.521 gauge pin — our specialists in Emmerich will advise on fitment and ordering via info@metav-werkzeuge.com or +49 2822 7131930 Technical data Article number: M323.521 GTIN: 4061905060007 Brand: Metav IndustryLine Facts Diameter: 5.21 mm Tolerance: ±0.001 mm Length: 50 mm Weight: 0.011 kg Special features Material: special steel Delivery: single item Designation: workshop version FAQ What is the declared tolerance of this gauge pin? The gauge pin M323.521 is specified with a tolerance of ±0.001 mm, ensuring high repeatability for inspection and fixture tasks. Can this test pin be used as a locating pin in jigs? Yes, the M323.521 gauge pin is suitable for locating and alignment duties where a precise 5.21 mm datum is required. What material is the pin made from and why does it matter? The pin is made from special steel; this provides wear resistance and dimensional stability under regular workshop handling. Is the product supplied individually or in a set? This item is supplied as a single precision test pin for direct replacement or targeted use in fixtures. How is the product identified for inventory and traceability? Identification is possible via the article number M323.521 and GTIN 4061905060007 for stock control and ordering Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
5.22mm Gauge Pin Length 50mm ±0.001mm Workshop Version - Metav IndustryLine
Combine micrometre-level accuracy with a compact 50 mm form and a ±0.001 mm tolerance for dependable end‑measure verification — order the part directly via Metav Werkzeuge or consult our specialists for application advice. M323.522 — Single gage pin (inspection pin), Ø 5.22 mm ±0.001 mm, length 50 mm The M323.522 single gage pin is a precision inspection pin intended for end‑measure checks and dimensional control in workshop and inspection environments. Micrometre tolerance ±0.001 mm Diameter 5.22 mm for end‑measure checks Compact 50 mm length for easy handling Micrometre accuracy for reproducible inspection results The gage pin delivers a ±0.001 mm manufacturing tolerance, making it suitable for tasks that demand sub‑millimetre repeatability and minimal measurement uncertainty. With a nominal diameter of 5.22 mm, the pin is dimensioned for end‑measure verification and reference‑checking in small bores or precision fixtures. This level of accuracy reduces rework and supports consistent quality control by providing a stable, known reference that complements comparators, micrometres and plug‑gage workflows. Robust dimensions and material for everyday workshop use Constructed from special steel, the pin balances wear resistance with manageable mass in a 50 mm length. The slim profile and low weight facilitate quick positioning and minimise lever‑effects during inspection, which helps to preserve measurement reliability across repeated cycles. The workshop‑grade execution ensures the pin performs reliably in routine inspection rounds and fits into existing gauge sets and inspection jigs without requiring special adapters. Designed to integrate into inspection processes and documentation As a single inspection element, the pin supports end‑measure tasks, reference alignment and quick go/no‑go checks within standard metrology setups. Traceability is facilitated by the clear article identification and GTIN, enabling straightforward inventory and quality documentation. For complex or automated measurement stations, the component functions as a fixed, high‑precision reference that simplifies setup and shortens inspection times while maintaining documented consistency. For traceable inspection tasks, request the M323.522 from Metav Werkzeuge — contact info@metav-werkzeuge.com or call +49 2822 7131930 for technical guidance and procurement assistance Technical data Article number: M323.522 GTIN: 4061905060014 Category: Gauge pins Label: Single gage pin, 5.22 mm, ±0.001 mm, length 50 mm Facts Diameter: 5.22 mm Tolerance: ±0.001 mm Length: 50 mm Weight: 0.011 kg Special features Material: Special steel Workshop version Application: End‑measure verification Accuracy class: ±0.001 mm FAQ What inspection tasks is this pin intended for? The M323.522 gage pin is intended for end‑measure verification, reference alignment and quick dimensional checks in small bores and precision fixtures. What is the declared manufacturing tolerance of the pin? The pin is produced to a tolerance of ±0.001 mm, providing micrometre‑level precision suitable for reproducible inspection results. Which material is used for the pin and how does it affect durability? The pin is made from special steel; this material choice offers workshop‑grade durability for repeated inspection cycles while maintaining dimensional stability. Can this single pin be used with existing gauge sets and comparators? Yes, the compact 50 mm length and nominal diameter of 5.22 mm make the pin compatible with standard comparators, micrometres and fixture systems as a reference element. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
5.23mm Gauge Pin, ±0.001mm Tolerance, Length 50mm, Workshop Version - Metav IndustryLine
Precision end‑size inspection benefits from the combination of ±0.001 mm tolerance, a 5.23 mm diameter and a 50 mm length in a durable workshop design. Made from special steel and supplied in a transport case, this single gauge pin supports repeatable plug measurements and safe handling in everyday metrology tasks. Order the gauge pin directly via Metav Werkzeuge or consult our advisors for tailored application support. Gauge pin M323.523 — 5.23 mm diameter, ±0.001 mm accuracy (Workshop version) — Metav IndustryLine The Gauge pin M323.523 is a single precision inspection pin designed for end‑size verification and routine plug measurements in workshop environments Tight tolerance ±0.001 mm Diameter 5.23 mm, length 50 mm Special steel, workshop version Accurate end‑size checks with micron‑level certainty The gauge delivers a ±0.001 mm manufacturing tolerance, which corresponds to micrometre‑class repeatability for go/no‑go and reference measurements. In practice, that level of accuracy reduces uncertainty when checking drilled bores, pin fits or assembly tolerances: a stable reference pin removes guesswork from end‑size inspection and speeds up decision making in production. The tight specified tolerance and compact geometry make the item particularly suited to precision control tasks where small deviations immediately affect assembly quality, so inspections become a reliable part of process control rather than a bottleneck. Built for daily workshop use — durable, compact and transportable Constructed from special steel, the workshop execution offers a balance of wear resistance and ease of handling that matches frequent use on the shop floor. With a length of 50 mm and a light mass, the pin is comfortable to manipulate and quick to insert into fixtures or bore gauges. Delivery in a dedicated transport case protects the ground surfaces during storage and transfer, lowering the risk of damage and measurement drift. The robust finish maintains geometry over time, ensuring consistent results between checks and fewer withdrawn parts due to inspection variability. Integrates into inspection routines and documentation Simple geometry and unambiguous specification allow straightforward incorporation into checklists, SPC routines and maintenance logs. The M323.523 pin can serve as a reference gauge for short control runs, batch release or final inspection steps, reducing non‑conformances through clear, repeatable criteria. Its compact size and precise tolerance also make it efficient for spot checks across a production line, saving time compared with more complex measurement setups. Backed by Metav’s quality‑first approach, the pin supports reliable traceability and sustained measurement confidence in everyday shop use. Contact Metav Werkzeuge for specification matching and prompt delivery from Emmerich — our advisors will assist with application planning and availability of the M323.523 gauge pin Technical data SKU: M323.523 GTIN: 4061905060021 Category: Gauge pins (Messstifte) Manufacturer: Metav IndustryLine Facts Diameter: 5.23 mm Length: 50 mm Tolerance: ±0.001 mm Weight: 0.011 kg Special features Material: special steel Workshop execution Supplied in transport case Designed for end‑size verification FAQ What level of accuracy does this gauge pin offer? The M323.523 gauge pin from Metav IndustryLine provides a tolerance of ±0.001 mm, making it suitable for micrometre‑class plug and fit checks. How is the gauge pin supplied for safe handling? The single gauge pin is delivered in a transport case to protect the ground surfaces during storage and movement, and is identified by SKU M323.523 and GTIN 4061905060021. Which applications suit this gauge pin best? The pin is intended for end‑size verification, plug measurements and routine inspection tasks in workshop and production environments where reliable repeatability is required. Is the design appropriate for frequent shop‑floor use? Yes. The workshop execution and special steel construction give the M323.523 robustness for daily inspection cycles while remaining easy to handle. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
5.24mm Gauge Pin Single ±0.001 mm Length 50 mm Workshop Finish - Metav IndustryLine
Take advantage of a finely balanced combination of dimensional certainty and robustness: a compact gauge pin with ±0.001 mm tolerance and a 50 mm working length, designed to speed up inspection tasks and reduce rework. Order the part directly via Metav Werkzeuge or consult our specialists for application advice. M323.524 single gauge pin — 5.24 mm, ±0.001 mm, 50 mm length (Metav IndustryLine) M323.524 is a single gauge pin engineered for precise end‑measurements and plug‑gauge checks in workshop and inspection environments Diameter 5.24 mm with ±0.001 mm accuracy Length 50 mm, workshop version Special steel construction for durability Delivered in protective transport case Precision that removes doubt from inspection The core advantage of this test pin is its metrological repeatability: with an uncertainty of ±0.001 mm the component supports high‑confidence go/no‑go checks and tight tolerance verification. Such fine tolerance translates into fewer false rejects and a clearer quality decision at the control station. The compact diameter and tight specification make the pin suitable for critical end‑measurements where small deviations directly affect assembly fit and function. Compact form for fast, repeatable handling A short, rigid length of 50 mm and a 5.24 mm diameter give the plug‑type pin excellent stiffness for single‑handed positioning and quick cycle checks. The compact format reduces bending and handling error during repetitive use, so measurement routines become faster and more reproducible. Where throughput matters, a small, robust gauge part like this reduces inspection time without sacrificing accuracy. Robust material for low maintenance and long service life Constructed from special steel in a workshop execution, the pin resists wear from repeated seating and contact with mating parts. The material choice ensures dimensional stability and a longer service interval compared with untreated components. Reduced wear means the tool maintains specification over time, limiting the need for frequent replacement and helping to keep inspection costs predictable. Protected delivery and practical traceability Delivered in a protective transport case, the gauge arrives ready for safe storage and immediate use, lowering the risk of transit damage. Identification via SKU and GTIN simplifies inventory management and traceability in busy production or inspection environments. The packaging also makes the part straightforward to integrate into kitting for fixtures, gauges or portable inspection sets. Contact Metav Werkzeuge for procurement and technical advice on the M323.524 gauge pin with ±0.001 mm accuracy and workshop‑grade durability Technical data Article number: M323.524 GTIN: 4061905060038 Weight: 0.011 kg Material: Special steel Length: 50 mm Diameter: 5.24 mm Tolerance: ±0.001 mm Execution: Workshop version Packaging: Protective transport case Facts Diameter: 5.24 mm Length: 50 mm Tolerance: ±0.001 mm Weight: 0.011 kg GTIN: 4061905060038 Special features Special steel construction Workshop execution for industrial use Delivered in protective transport case Compact, stiff geometry for repeatable checks FAQ What is the measurement tolerance of this gauge pin? The M323.524 gauge pin is specified to ±0.001 mm, suitable for tight tolerance plug‑type inspections. Which tasks is the pin intended for? This test pin is designed for end‑measurements, plug‑gauge checks and dimensional verification in workshop and inspection settings. What material is used for the pin? The pin is made from special steel in a workshop execution to provide wear resistance and dimensional stability. How is the part delivered and documented? The pin is supplied in a protective transport case for secure handling and storage; identification is provided via SKU and GTIN for traceability. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
5.25mm Gauge Pin, Workshop Version, ±0.001mm Accuracy, 50mm Length - Metav IndustryLine
Taking advantage of high repeatability and a workshop-ready design, this gauge pin combines 5.25 mm nominal diameter with a fine ±0.001 mm tolerance and a 50 mm shank for consistent end-measurement checks; order directly via Metav Werkzeuge or consult our specialists for application advice. Gauge pin, single, 5.25 mm, ±0.001 mm — Metav IndustryLine Gauge pin, single, 5.25 mm, ±0.001 mm is a precision measurement pin for end‑dimension verification and fixture testing in production and inspection environments Workshop execution for robust use Diameter 5.25 mm with ±0.001 mm tolerance 50 mm length for deep or recessed checks Supplied in a transport case for protection Precision that reduces rework and inspection uncertainty The instrument delivers ±0.001 mm dimensional accuracy, making it suitable for critical end‑measure checks and tight tolerance inspections in metalworking and precision assembly. Built to provide consistent contact geometry, this test pin ensures repeatable measurements when used in gauges, fixtures or manual verification routines. The tight tolerance reduces the need for corrective work and supports reliable quality decisions, translating into measurable productivity gains on the shop floor. Robust material and form for everyday workshop use Manufactured from Special steel and offered in a workshop execution, the pin resists wear and keeps measurement geometry stable over repeated use. The 50 mm shank length enables access to deeper bores and recessed features while maintaining sufficient rigidity for direct probing. The solid design minimises flex under normal handling and, when used with appropriate fixtures, extends service life compared with lower‑grade pins — a practical advantage where durability and uptime matter. Practical traceability and simple integration into inspection processes Marked with SKU M323.525 and GTIN 4061905060045, the single gauge pin is straightforward to document in quality records and to integrate into inspection sets. The compact single‑item format suits bespoke gauge stations and targeted sampling procedures without the footprint of larger kits. Supplied in a protective transport case, the pin is kept safe between uses, simplifying storage and reducing the risk of accidental damage that would otherwise impair measurement certainty. Choose Metav IndustryLine gauge pins for repeatable precision in production; contact Metav Werkzeuge in Emmerich for tailored advice and ordering via info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: M323.525 GTIN: 4061905060045 Manufacturer: Metav IndustryLine Facts Diameter: 5.25 mm Length: 50 mm Accuracy: ±0.001 mm Weight: 0.011 kg Special features Material: Special steel Version: Workshop execution Packaging: Delivered in transport case FAQ What tolerance does this gauge pin provide? The gauge pin offers a tolerance of ±0.001 mm, as specified for the Metav IndustryLine single gauge pin M323.525. What are the nominal diameter and length? The nominal diameter is 5.25 mm and the overall shank length is 50 mm, suitable for recessed checks and fixture use. Is the pin suitable for workshop and production environments? Yes, the workshop execution and Special steel construction make the gauge pin resilient to everyday handling in production and inspection settings. How is the product supplied to protect measurement geometry? The single gauge pin M323.525 is supplied in a transport case to protect the measurement surface during storage and transport. Can the pin be documented in quality systems? Yes, the Metav IndustryLine gauge pin is identified by SKU M323.525 and GTIN 4061905060045 for traceability in inspection records. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
5.26mm Precision Test Pin ±0.001mm Length 50mm, Workshop Version - Metav IndustryLine
Take advantage of the workshop-grade combination of a 5.26 mm diameter, ±0.001 mm tolerance and a solid 50 mm length for repeatable end-measurements and secure fit checks. Order the gauge pin directly via Metav Werkzeuge or consult our specialists for application advice. Gauge pin (single) M323.526 — 5.26 mm, ±0.001 mm, 50 mm length by Metav IndustryLine The gauge pin M323.526 is a single, workshop-grade test pin for precise end-measurements and go/no‑go checks in production and inspection tasks Workshop version for daily use Diameter 5.26 mm with ±0.001 mm tolerance Length 50 mm for compact assemblies Supplied in a protective case Repeatable accuracy for production control The workshop pin delivers ±0.001 mm positional certainty, making it suitable where repeatable end-measurements and tight fit verification are required. Manufactured for metrology environments, the component offers a stable reference for dimensional checks and assembly controls. The very fine tolerance supports confident decision‑making in quality inspection, reducing rework and scrap rates while integrating smoothly into established inspection workflows. Robust design built for shop-floor handling Made from special steel and specified as a workshop version, the pin combines corrosion resistance and wear tolerance with handling-friendly dimensions. The 50 mm length keeps the pin rigid in hand and in fixtures, while the 5.26 mm diameter maintains concentricity for insertion into bores and gauges. This robustness ensures sustained performance under frequent use, lowering the need for early replacement and supporting continuous production. Practical delivery and application benefits Supplied as a single piece and delivered in a protective case, the gauge pin is ready for transport and storage without immediate additional packaging. The compact format and clearly specified dimensions simplify inventory management and project planning. As a standard test pin for end-measurements, it can be used for quick go/no‑go trials, alignment checks and replacement in modular gauge assemblies where predictable, certified dimensions are essential. For workshop-grade precision from Metav IndustryLine, contact Metav Werkzeuge for detailed application guidance and dependable delivery from Emmerich: info@metav-werkzeuge.com, +49 2822 7131930 Technical Data SKU: M323.526 GTIN: 4061905060052 Manufacturer: Metav IndustryLine Facts Diameter: 5.26 mm Length: 50 mm Tolerance: ±0.001 mm Weight: 0.011 kg Special features Material: Special steel Workshop version Single gauge pin Delivery in protective case FAQ What measurement accuracy does this pin provide? The gauge pin M323.526 offers an accuracy of ±0.001 mm, intended for precise end-measurements and tight tolerance checks. Is the pin suited for repeated shop-floor use? Yes, the workshop-version construction and special steel of this test pin provide the robustness required for frequent handling and inspection cycles. What are the exact dimensions and identifier for ordering? The pin measures 5.26 mm in diameter and 50 mm in length; order as SKU M323.526 from Metav IndustryLine. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
Fast, tactile checks where electronics are impractical
Gauges and test pins provide unequivocal go/no-go results for threads, bores, gaps and radii without relying on electronics. The range covers plug gauges and ring gauges for internal and external threads, feeler gauges and precision feeler strips for micro‑gap assessment, plus probe pins and measuring pins for tactile diameter and pitch checks.
How these tools work in the production environment
Mechanical gauges operate as direct reference standards: a plug gauge or ring gauge verifies conformity to thread profiles and mating ability, while limit gauges separate accept from reject in a single step. Test pins are used to tactilely measure small bore diameters, centre‑to‑centre distances and radii. Manufactured from hardened gauge steel or ceramic and often precision lapped, these instruments deliver immediate physical results that are ideal for incoming inspection, machine‑side checks and final control.
Measurable benefits that affect production performance
- Reduced scrap and rework through rapid, unambiguous pass/fail assessment.
- Increased repeatability thanks to very low measurement uncertainty and fine lapping.
- Lower downtime: quick checks at the machine save cycle time and reduce setup periods.
- Durable construction with high wear resistance from specialised, low‑distortion alloys.
- Versatile delivery formats: individual gauges, organised sets in wooden cases or metre‑length feeler rolls compliant with DIN 2269.
Why Metav is the practical choice for precision supplies
Metav combines decades of expertise with a broad warehouse and quality filtering from Emmerich. As a precision partner for industry, craft and trade, Metav supplies a comprehensive selection of gauges and test pins alongside complementary tools such as precision calipers and setting rings. With over 48,000 customers and a catalogue exceeding 250,000 items, Metav is positioned to supply reliably, reduce vendor complexity and support traceable quality control to national standards.
Summary
Gauges and test pins are indispensable for dependable, repeatable quality assurance where tactile, mechanical verification is preferred. Choose these plug gauges, ring gauges, feeler strips and probe pins when immediate, robust measurement decisions are required on the shop floor.
FAQ
What materials are gauges and test pins typically made from?
Gauges and test pins are usually manufactured from hardened gauge steel for durability and wear resistance; ceramic variants are available where thermal stability and minimal wear are critical.
How do thread gauges ensure mating capability?
Thread plug gauges and ring gauges check flank diameters and thread form against standards, providing a clear go/no‑go verdict that confirms pairability with mating parts.
Which tolerance class should I choose for probe pins and gauge sets?
Select tolerance classes aligned with your inspection requirements; for high‑precision tasks, sets produced to DIN 2269 or equivalent tolerance classes ensure micrometre‑level control and repeatability.
Can feeler gauges measure contact gaps in valve and engine work reliably?
Yes. Feeler gauges and precision feeler strips, supplied either as a fan or metre‑length rolls, allow accurate assessment of valve clearances and contact gaps down to micrometre increments.
How do limit gauges speed up in‑process inspection?
Limit gauges separate good from bad in a single, tactile operation, enabling rapid go/no‑go checks at the machine and reducing both inspection time and the likelihood of human interpretation errors.
Fragen zu diesen Produkten??
Mit mehr als 30 Jahren Erfahrung beraten wir Sie gerne persönlich.
Tel.: +49 2822 7131930
Mail: info@metav-werkzeuge.com