Precision gauge blocks and plug gauges for reliable dimensional control
Mechanical gauge blocks and plug gauges are essential for tactile verification of threads, bores and gap dimensions, providing fast, unambiguous go/no-go results that enhance process reliability and reduce scrap. Designed for industrial metalworking and toolmaking, these precision tools support incoming inspection and final quality checks by delivering traceable measurements in applications such as thread inspection, bore diameter testing and spacing checks. Manufactured from specially hardened, low-distortion alloys and fine-lapped for minimal measurement uncertainty, the range includes thread plug gauges, precision plug gauges and calibration gauge blocks to ensure long-term repeatability and wear resistance.
62 mm Limit Gauge Plug, H7 Fit, Hardened Gauge Steel, DIN 2245 - Metav IndustryLine
Ensure reproducible bore inspection through the combination of DIN 2245 H7 accuracy and hardened gauge steel construction; the result is fast, reliable go/no-go checks that keep production flowing. Order the Limit plug gauge M314.062 directly via Metav Werkzeuge or consult our specialists for application advice. Limit plug gauge M314.062 — 62.00 mm plug gauge, DIN 2245 H7 (Metav IndustryLine) The Limit plug gauge M314.062 is a hardened gauge-steel plug designed for rapid go/no-go verification of 62.00 mm bores to DIN 2245 H7 tolerance in production and inspection workflows. DIN 2245 H7 compliance for bore checks Hardened gauge steel construction Nominal diameter 62.00 mm for consistent checks Designed for go/no-go inspection workflows Accuracy and conformity for everyday inspection needs The plug gauge offers a straightforward way to confirm bore conformity to H7 tolerance as defined by DIN 2245, delivering a clear go/no-go decision without interpretation. Machining and quality departments benefit from reduced measurement time and fewer downstream rejects because the tool enables immediate verification at the bench or on the shop floor. Built to industrial practice, this limit gauge supports repeatable inspection sequences and situational decision-making, improving throughput while preserving documented compliance. Robust construction that withstands workshop conditions Made from hardened gauge steel, the gauge is engineered for durability and wear resistance in routine use. The material choice ensures dimensional stability over repeated cycles and protects the inspection result against typical shop-floor influences. This mechanical resilience translates into lower lifetime cost per inspection and dependable readings across production batches, which is particularly important where traceable checks are carried out at short intervals. Practical handling and integration into inspection routines The simple go/no-go design avoids the need for advanced measurement equipment in every station: the 62.00 mm nominal size provides an immediate pass/fail outcome that fits established assembly and receiving processes. For quality managers this means fewer measurement steps and faster worker training, while workshop staff gain a compact, easy-to-store tool that supports consistent inspection habits. The form factor is suitable for manual checks and integration into fixtures where quick verification is required. Why this gauge matters for production control Using a calibrated limit gauge that adheres to recognised standards reduces ambiguity in quality control and accelerates conformity decisions. The product supports a pragmatic quality strategy: use standardised mechanical gauges for rapid sorting and reserve time-consuming dimensional checks for critical samples. The result is a balanced inspection approach that protects product quality, shortens cycle times and sustains traceability throughout production. Specify the Metav IndustryLine limit plug gauge for reliable go/no-go inspections and contact Metav Werkzeuge in Emmerich for technical guidance and supply coordination. Technical data Article number: M314.062 GTIN: 4054469121796 Manufacturer: Metav IndustryLine Standard: DIN 2245 Key figures Nominal diameter: 62.00 mm eCl@ss: 21170218 Customs tariff number: 90173000 SKU: M314.062 Materials & features Material: gauge steel, hardened Tolerance class: H7 Application: go/no-go bore inspection Category: gauges, plug gauges FAQ What tolerance does this plug gauge check? The limit plug gauge checks bores to the H7 tolerance specified by DIN 2245; the tool provides a clear go/no-go decision for conformity assessment. Is the gauge suitable for production-line inspections? Yes, the hardened construction and straightforward go/no-go format of the Metav IndustryLine limit plug gauge M314.062 make it well suited for rapid checks in production and incoming inspection. What material is the gauge made from? The gauge is manufactured from hardened gauge steel, chosen for wear resistance and dimensional stability during repeated use. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
62mm Setting Ring Form C Hardened Gauge Steel DIN 2250, JS3 - Metav IndustryLine
Take advantage of the combination of DIN‑rated accuracy, hardened and lapped gauge steel, and a compact 62 mm diameter for dependable master gauging in production and inspection. Secure the item directly via Metav Werkzeuge or consult the Metav team for application support and specification advice. Setting Ring 62 mm — Hardened, Lapped Ring Gauge (Metav IndustryLine) The Setting Ring 62 mm is a hardened and lapped master ring gauge designed for accurate bore verification and calibration tasks in inspection benches and workshop environments. Ring gauge 62 mm, DIN 2250 compliant Hardened and lapped gauge steel Tolerance JS 3 for precision fit Suitable for workshop and inspection use Consistent inspection accuracy for repeatable results A master ring of 62 mm diameter offers a reliable reference for checking internal diameters and setting bore-measuring instruments. Manufactured from gauge steel, hardened and lapped, the element provides a stable contact surface that resists wear and maintains form integrity during regular use. Compliance with DIN 2250 and DIN 286 ensures interchangeability with standard tooling and fixtures; the JS 3 tolerance delivers a precise fit that supports tight control limits and reduces rework rates. Robust design that eases handling and longevity The component’s construction balances mass and manageability: at 1.3 kg, it is substantial enough to stay stable during measurements yet compact for hand-held handling or fixture mounting. The Form C configuration simplifies alignment in common inspection setups and contributes to reproducible seating against mating parts. Lapping produces a fine surface finish that minimises measurement scatter and extends service intervals, so maintenance cycles are simplified and downtime is reduced. Practical integration into quality-control workflows As a master reference, the ring gauge serves both as a calibration artefact for bore gauges and as an in-line check for batch production. The robust material and normative conformity mean it can be used confidently on the shop floor as well as in the inspection room. Traceable identification (SKU M313.062, GTIN 4054469120881) supports asset management and documentation in quality systems. For customers who require specification matching, Metav IndustryLine offers clear data to aid selection and process planning. Discuss specific application requirements with Metav Werkzeuge to confirm suitability and arrange supply of the 62 mm setting ring (M313.062) for immediate integration into quality routines Technical data Article number: M313.062 GTIN: 4054469120881 Category: Lehren Facts Diameter: 62 mm Weight: 1.3 kg Customs tariff: 90173000 Special features Material: Gauge steel, hardened and lapped Standard: DIN 2250; DIN 286; JS 3 Form: C FAQ What tolerance class does the setting ring meet? The ring meets JS 3 tolerance according to the stated standards, providing a precision fit suitable for master gauging and dependable reference use with bore gauges and plug gauges. What material and finish are used on this gauge? Manufactured from hardened and lapped gauge steel, the Setting Ring 62 mm (Metav IndustryLine, M313.062) offers a fine surface finish for stable contact and extended wear resistance. Can this ring be used on the shop floor? Yes, the robust construction and normative conformity make the ring appropriate for both workshop checks and inspection-room calibration duties. Which standards apply to this ring gauge? The product complies with DIN 2250 and DIN 286, which ensures compatibility with standardised measurement procedures and fixtures. How is the ring identified for inventory and traceability? The item is listed as SKU M313.062 and carries GTIN 4054469120881 for unambiguous identification in quality and inventory systems. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
63/32/16/8/4/2 µm Surface Comparison Plate, 6-Piece Set Grinding Textures, Ra 1.6–0.05 µm - Metav IndustryLine
Achieve consistent surface verification with a compact reference set that covers a wide Ra range and fits easily on any inspection bench; the six comparison plates provide distinct tactile and visual grades for immediate assessment. Order the Surface Comparison Plate "Grinding" set directly via Metav Werkzeuge or ask our consultants if needed. Surface Comparison Plate "Grinding" — six-piece comparison set, Ra 0.05–1.6 µm (Metav IndustryLine) The Surface Comparison Plate "Grinding" is a compact reference set designed for quick visual and tactile assessment of ground surface finishes in workshop and inspection applications. Reference Ra range 0.05–1.6 µm Six distinct grinding comparison plates Compact and lightweight at 0.2 kg Faster, more reliable surface checks for grinding The set provides a series of comparison plates that represent distinct ground surface textures; each grade corresponds to a defined Ra value in µm, allowing immediate side‑by‑side evaluation. Using these standards reduces subjective judgement during routine checks and supports faster acceptance or rejection decisions at the machine. The clear gradation between plates simplifies communication across shifts and shortens process loops, which improves overall throughput without additional measurement equipment. Support for consistent process control and quality assurance By referencing repeatable tactile and visual standards, the set helps to maintain a stable surface finish specification across batches. The plates are suitable as a shop‑floor reference for grinding operations, enabling operators and inspectors to align on finish targets before committing parts to final inspection. This practical approach complements formal measurement instruments and contributes to fewer reworks and more predictable quality outcomes, reinforcing efficient production planning and reduced scrap rates. Practical design that suits the workshop environment Engineered for bench use, the set is compact, lightweight and easy to handle, so it can remain available at the point of work for immediate comparison. The plates cover a practical spread of finishing grades commonly encountered in grinding, making them a handy companion for grinding operators, toolmakers and quality technicians. As a robust visual and tactile reference, the set supports both quick informal checks and formal inspection routines when combined with instrumental measurements. Contact Metav Werkzeuge for guidance on integrating the Metav IndustryLine surface comparison plates into existing inspection routines and for advice tailored to grinding applications Technical Data Article number: M318.036.1 GTIN: 4054469146270 Description: Surface comparison plate "Grinding", 6-piece set Facts Ra (µm): 1.6 / 0.8 / 0.4 / 0.2 / 0.1 / 0.05 Number of plates per set: 6 Weight: 0.2 kg Tariff number: 90173000 Special features Set for grinding surface comparison Distinct, graduated surface grades for visual/tactile comparison Shop‑floor and inspection bench suitability Category: Gauges / Comparison standards FAQ What range of surface roughness do the comparison plates represent? The plates cover Ra values from 0.05 µm to 1.6 µm, offering fine gradations for typical ground finishes and enabling quick visual and tactile checks with the Surface Comparison Plate "Grinding" set. How should the plates be used during grinding operations? Use the plates as a bench‑side reference: compare the workpiece surface against the appropriate plate to evaluate whether the finish meets the targeted surface finish specification before final measurement or handover. Are the comparison plates suitable for final inspection or only for rough checks? The set is intended as a reference for immediate quality control and process alignment; it complements instrument measurements and helps to reduce subjective variation during pre‑inspection checks. Can the set be used for other finishing processes besides grinding? While optimised for ground surfaces, the graduated plates may be useful for comparing finishes from other processes that produce similar texture ranges; suitability depends on the target Ra values. What does the Metav IndustryLine branding imply for the comparison plates? Metav IndustryLine signifies a practical, shop‑oriented standard that fits the philosophy of accessible precision: durable, consistent reference plates designed for everyday use in workshops and inspection benches. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
65mm Limit Plug Gauge DIN 2245 H7 Hardened Gauge Steel 1.4 kg - Metav IndustryLine
Taking advantage of DIN 2245 conformity and a 65.00 mm H7 inspection diameter ensures reliable, repeatable acceptance checks; the hardened gauge steel construction delivers long service life and consistent fits. Order the gauge directly via Metav Werkzeuge or request a technical consultation from our specialists. Limit plug gauge M314.065 — 65.00 mm H7, DIN 2245 compliant The M314.065 limit plug gauge is a precision cylindrical gauge designed for rapid go/no‑go inspection of bores to DIN 2245 tolerances in production and quality control environments. Conforms to DIN 2245 tolerance system Hardened gauge steel for wear resistance Diameter 65.00 mm with H7 inspection fit Precision ground finish for reliable fits Certainty in tolerance control for serial production A gauge built to DIN 2245 gives a clear, standardised basis for acceptance decisions in machining and assembly processes. The defined H7 mating condition means the gauge represents the nominal bore limit used across engineering drawings and inspection plans; this removes ambiguity during rapid checks and supports consistent quality documentation. The instrument’s role is to provide an immediate, unambiguous verdict on a bore’s conformance so that downstream processes run without interruption and scrap or rework is reduced. Durable construction for sustained accuracy Made from gauge steel, subsequently hardened and precision ground, the gauge resists wear that would otherwise alter the measured limit. The material choice and finishing process preserve the functional gauge face and maintain repeatability over many inspection cycles, reducing the frequency of replacement. Where repeatability and low measurement uncertainty are required, a robust plug gauge ensures that production control remains efficient and predictable. Fast, operator‑friendly go/no‑go inspection As a limit gauge, the component enables swift pass/fail checks that integrate directly into production lines or inspection benches. The clear physical limit for acceptance accelerates decision making and reduces operator interpretation, which supports higher throughput and fewer measurement disputes. The compact cylindrical design is easy to handle and aligns with common fixture and bench arrangements, promoting ergonomic inspection routines and a measurable improvement in process reliability. Request a technical quotation or product consultation from Metav Werkzeuge to verify fitment and delivery options for the Metav IndustryLine limit plug gauge M314.065 — our experts in Emmerich will advise on application suitability and supply logistics Technical data Article number: M314.065 GTIN: 4054469121802 EClass: 21170218 Tariff code: 90173000 Facts Diameter: 65.00 mm Tolerance: H7 Standard: DIN 2245 Special features Material: gauge steel, hardened Finish: precision ground Category: limit plug gauge / go/no‑go gauge Intended use: bore inspection in production FAQ What tolerance system does the gauge follow? The limit plug gauge is manufactured to DIN 2245, providing the familiar tolerance framework used for bore acceptance in industrial practice. Is the inspection diameter specified exactly? Yes, the gauge checks a 65.00 mm bore to the H7 limit condition as indicated by the product designation M314.065. What material and treatment are used for durability? The M314.065 is made from gauge steel and is hardened and precision ground to sustain repeated go/no‑go checks with minimal wear. Can this gauge be used on production lines for quick checks? The plug gauge is intended for rapid acceptance testing; its cylindrical design and clear limit function make it suitable for integration into manual inspection benches and assembly stations. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
65mm Setting Ring Form C Hardened Gauge Steel DIN 2250/DIN 286 JS3 - Metav IndustryLine
Take advantage of a hardened and lapped gauge ring that meets DIN 2250 and DIN 286 with JS 3 tolerance, offering a stable 65 mm reference for rapid, repeatable setting in quality control; order directly via Metav Werkzeuge or consult our advisors for specification support. Setting ring 65 mm (gauge ring) – hardened & lapped – Metav IndustryLine The Setting ring 65 mm is a hardened, lapped gauge ring designed as a precise reference standard for calibration and setting tasks in workshops and inspection environments in accordance with DIN 2250 and DIN 286. Hardened and lapped gauge steel Conforms to DIN 2250 and DIN 286, JS 3 Nominal diameter 65 mm Stable reference for gauge and instrument setting Reliable reference for routine calibration and setup The Setting ring 65 mm serves as a compact, robust reference standard for reproducible gauge setting and instrument alignment. Manufactured to the relevant DIN standards, the ring provides a definable nominal diameter and tolerance grade (JS 3) that supports consistent readings when used to set comparators, micrometers or master-stem systems. As a workshop-ready reference, the component reduces setup variation and contributes directly to process stability and fewer reworks, making it a practical choice for production metrology and incoming inspection. Durable materials and precision finishing for long-term stability Made from hardened and lapped gauge steel, the ring combines hardness for wear resistance with a lapped surface finish that minimises contact irregularities and run-out. The Form C geometry delivers a pragmatic balance between handling and seating stability during contact measurements. These manufacturing choices extend service life and preserve repeatability, so reference values remain reliable over many cycles. Lapping removes microscopic surface peaks, which improves contact conformity and supports consistent tactile feel when setting measurement instruments. Practical benefits in the workshop and inspection lab Compact and robust by design, the gauge ring provides a straightforward reference that integrates into existing calibration routines without special fixtures. The nominal 65 mm diameter is suited to medium-range reference tasks where space-saving standards and quick handling are required. Use of this reference ring helps to shorten setup times and reduces measurement uncertainty introduced by inconsistent setting practices. The clear conformity to established standards supports traceability in quality records and aligns with common metrological procedures in small and mid-sized manufacturing operations. For assured reference quality and fast dispatch from Emmerich, choose the Metav IndustryLine setting ring and contact Metav Werkzeuge for detailed specification advice and ordering support. Technical data Article number: M313.065 GTIN: 4054469120898 Nominal diameter: 65 mm Weight: 1.3 kg Form: Form C Facts Standards: DIN 2250, DIN 286 Tolerance grade: JS 3 Tariff number: 90173000 ECLASS: 21170104 Special features Material: hardened and lapped gauge steel Application: reference standard for gauge setting and calibration Category: gauge rings / setting rings Suitable for workshop and inspection use FAQ What standards does the ring comply with? The setting ring is manufactured to DIN 2250 and DIN 286 and supplied with the specified JS 3 tolerance grade for traceable reference use. Is the ring suitable as a master for setting micrometers and comparators? Yes, the gauge ring is intended as a stable reference for setting comparators, micrometers and similar measuring devices in workshop and inspection applications. What material and finish are used to ensure durability? The component is produced from hardened and lapped gauge steel, a combination chosen for wear resistance and a low-friction, high-conformity surface finish. Does the geometry support stable seating during measurement? The ring is supplied in Form C, which provides reliable seating and handling characteristics for regular calibration tasks. Which catalogue identifier should be used when ordering? Refer to article number M313.065 (Setting ring 65 mm) when placing orders or requesting further technical documentation. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
68 mm Setting Ring Form C, Hardened Gauge Steel, DIN 2250 / DIN 286 JS3 - Metav IndustryLine
The combination of hardened and lapped gauge steel, a stable Form C profile and strict conformity to DIN 2250 / DIN 286 JS 3 delivers a robust reference for repeatable set-ups and reduced rework. Order the setting ring directly via Metav Werkzeuge or consult the technical team for integration advice. Setting ring gauge M313.068 — 68 mm diameter, hardened and lapped gauge steel (Form C) | Metav IndustryLine The Setting ring gauge M313.068 provides a workshop-grade reference for diameter verification and tool setting in machining, inspection and fixture preparation. 68 mm nominal diameter, Form C Hardened and lapped gauge steel Manufactured to DIN 2250 / DIN 286 JS 3 GTIN 4054469120904 Consistent set-ups that reduce scrap and downtime A precisely manufactured setting ring offers a stable datum for repeated adjustments; the ring’s geometry is controlled to meet DIN 2250 and DIN 286 JS 3, which translates into predictable repeatability when used as a reference for tool setting and go/no‑go verification. The standardised tolerance class reduces subjective interpretations during machine set-up and speeds process handovers between shifts. Where traceable references are required in an inspection chain, this ring functions as a compact master that helps to avoid costly part rework and supports continuous production flow. Durable construction for routine workshop use The body is made from gauge steel, hardened and lapped to present a wear‑resistant measuring surface that retains form over time; the Form C profile ensures reliable seating against shafts and mandrels. At 68 mm diameter and approximately 1.3 kg, the component offers sufficient mass for stable placement while remaining manageable for routine handling. The lapped finish lowers friction and contact wear, extending service life and maintaining the integrity of the measurement surface, which benefits both quality assurance and long‑term cost of ownership. Traceability and simple integration with inspection routines Marked with GTIN 4054469120904 and identified as M313.068, the ring is prepared for serial record‑keeping and spare part management in the workshop. Conformity to recognised standards makes documentation straightforward when integrating the ring into inspection plans or quality manuals. Delivered as a ready‑to‑use setting gauge, the component slots into existing processes for calibrating instruments or verifying external diameters, supporting consistent results across production runs while simplifying procurement and inventory tracking through the Metav IndustryLine catalogue. Contact Metav Werkzeuge for tailored technical advice or to reserve the Metav IndustryLine setting ring M313.068 for your workshop; call +49 2822 7131930 or e‑mail info@metav-werkzeuge.com Technical data Article number: M313.068 GTIN: 4054469120904 Diameter: 68 mm Weight: 1.3 kg Material: gauge steel, hardened and lapped Form: C Standards: DIN 2250; DIN 286, JS 3 Facts Diameter: 68 mm Weight: 1.3 kg Tariff number: 90173000 ECLASS: 21170104 Special features Form C geometry for shaft seating Hardened and lapped measuring surface Conforms to DIN 2250 and DIN 286 JS 3 Category: Gauges; measuring pins FAQ What accuracy and tolerance class does the ring meet? The setting ring gauge M313.068 is produced to the tolerance requirements of DIN 2250 and DIN 286 with class JS 3, providing a defined reference for compliant inspection and set‑up work. Which materials and surface treatments are used? The ring is manufactured from gauge steel that has been hardened and lapped to provide a wear‑resistant, low‑friction measuring surface suitable for frequent contact with shafts and mandrels. How should the ring be used within a workshop inspection routine? Use the M313.068 as a reference master for setting calipers, checking external diameters and verifying tool set‑ups; its standard conformity simplifies inclusion in formal inspection procedures. Is the product identified for inventory and traceability? Yes, the item is identifiable by GTIN 4054469120904 and article number M313.068 to support tracking, spare‑part ordering and documentation. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
68mm Limit Go/No-Go Plug Gauge H7 Hardened Gauge Steel DIN 2245 - Metav IndustryLine
The provided product data contains mutually exclusive quality indicators: the item is flagged both as good and as scrap. Because of this contradiction, a reliable, production-ready product description cannot be created from the current dataset. Please supply corrected and consistent information clarifying the item's inspection status and any relevant technical details such as the nominal diameter, applicable standard, and material specification. Once the inconsistency has been resolved, a complete, standards-compliant product text that follows Metav editorial requirements can be prepared promptly. For assistance in checking or correcting the data, please contact Metav Werkzeuge at info@metav-werkzeuge.com or by telephone on +49 2822 7131930.
6mm Ceramic Setting Ring 0.001mm Accuracy, Workshop Grade - Metav IndustryLine
Benefit from a compact calibration standard that combines ±0.001 mm accuracy with the durability of zirconia ceramic and a hardness of HV 1250 for reliable, repeatable workshop measurements; order the gauge directly via Metav Werkzeuge or consult our specialists for integration advice. Ceramic setting ring 6 mm — 0.001 mm accuracy, Metav IndustryLine The Ceramic setting ring 6 mm 0.001 mm is a compact calibration standard designed for workshop metrology and routine setting tasks where high repeatability and wear resistance are required. Zirconia ceramic, corrosion‑resistant Hardness HV 1250 for long life Accuracy ±0.001 mm Workshop version, wear‑resistant Accurate reference for repeatable settings A calibration standard with ±0.001 mm declared accuracy provides a solid basis for repeatable tool and gauge setups in the shop. The high resolution and low deviation reduce rework and inspection time, enabling measurable improvements in process stability. As a small form‑factor ring, it serves as a dependable reference for setting instruments and verifying measuring equipment without complex procedures. The declared precision supports quality control routines that rely on consistent baselines rather than frequent recalibration. Durable ceramic construction minimises maintenance Constructed from zirconia ceramic, the ring is inherently wear‑resistant and non‑magnetic, offering excellent dimensional stability in harsh workshop environments. The material’s high HV 1250 hardness lowers abrasion and extends service intervals compared with soft standards. Corrosion‑resistant properties ensure the reference surface remains unchanged by oil, coolant or humidity, so calibrations stay valid longer and the frequency of replacements is reduced — a clear operational saving for busy production floors. Compact design for practical shop use The compact geometry and workshop specification prioritise easy handling and straightforward integration into existing measurement workflows. The small diameter of 6 mm and the concise overall format make the ring suitable for confined or precision setups where larger standards are impractical. Its shape allows secure seating in fixture pockets or micrometer anvils, delivering stable contact conditions that contribute to consistent readings and efficient set‑up procedures. Confidence for quality assurance and traceability Supplied as a workshop‑grade reference, the ring supports traceable adjustment and verification activities in routine inspection loops. Use of a stable ceramic reference reduces the influence of magnetic interference and surface wear on measurement outcomes. For manufacturing operations aiming to meet tight tolerances, the combination of material characteristics and ±0.001 mm accuracy offers a reliable technical foundation for internal quality checks and process control. For enquiries on how the Metav IndustryLine ceramic setting ring can be integrated into measurement protocols or to request procurement via Metav Werkzeuge, please contact our metrology advisors at info@metav-werkzeuge.com or call +49 2822 7131930. Technical Data Article number: M313.K06 Label: Keramik-Einstellring 6 mm 0.001 mm (30x8) Facts Accuracy: ±0.001 mm Hardness: HV 1250 Diameter: 6 mm Dimensions: 30 x 8 mm Special features Material: zirconia ceramic Non‑magnetic Wear‑resistant Workshop version FAQ What is the primary use of this ceramic setting ring? The ceramic setting ring is intended as a compact calibration standard and setting reference for workshop metrology, enabling repeatable adjustments and checks with the declared ±0.001 mm accuracy for the M313.K06. Is the ring suitable for use near magnetic fields or on magnetic instruments? Yes, the ring is non‑magnetic, making it suitable for use where magnetic interference could affect steel standards or sensitive measuring instruments. How does the ceramic material affect longevity and maintenance? Zirconia ceramic offers high HV 1250 hardness and excellent wear resistance, which prolongs service life and reduces maintenance and replacement frequency compared with softer reference materials. Can this ring be used for routine calibration tasks on the shop floor? The workshop version is designed specifically for shop‑floor integration and routine verification tasks, providing a robust, compact reference for everyday measurement procedures. Metav IndustryLine: Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
6mm Gauge Pin 50mm Length ±0.001mm Workshop Version - Metav IndustryLine
Benefit from pinpoint accuracy, compact dimensions and workshop-grade robustness: the 6.00 mm gauge pin delivers ±0.001 mm tolerance in a 50 mm length for repeatable end measurements. Order the gauge pin directly via Metav Werkzeuge or ask our consultants if needed. Gauge pin M323.600 — 6.00 mm, ±0.001 mm, 50 mm length (Metav IndustryLine) The Gauge pin M323.600 is a single, high-precision test pin designed for reliable end‑measurement and inspection use in workshop and production environments. Single gauge pin 6.00 mm with ±0.001 mm tolerance 50 mm special-steel length for workshop use Workshop version optimised for inspection tasks Supplied in protective transport case High-precision control that reduces measurement uncertainty The pin offers a ±0.001 mm tolerance, providing a level of accuracy that narrows decision margins in quality checks and first‑off inspections. Such precision makes the pin suitable where reproducible Go/No‑Go checks or reference fits determine downstream processes; the small diameter of 6.00 mm helps to verify bores, gauges and fixture seats with minimal fixturing effort. By lowering measurement uncertainty, the component supports faster acceptance decisions and fewer reworks, which improves throughput in repetitive inspection routines. Robust design for everyday workshop use Constructed from special steel, this workshop‑grade test pin balances wear resistance with compact handling. The 50 mm length keeps the component manageable in tight setups while providing sufficient engagement for end‑dimension verification. The workshop version designation means the item is intended for frequent handling and routine checks rather than delicate laboratory-only tasks, so repeatability and endurance are focal benefits. Supplied in a protective case, the pin is protected during transport and storage, maintaining its geometric integrity until use. Integrates with inspection jigs and production fixtures Small, precise and simple, the pin is straightforward to incorporate into existing inspection fixtures, plug gauges and modular checking stations. Its consistent diameter and tolerance simplify alignment tasks and reduce setup time when swapping reference pins or calibrating fixtures. The design supports efficient process control: fewer adjustments are required between checks, which helps to maintain steady production rhythms and predictable inspection intervals. Confidence through traceable supply and practical support Sourced via Metav IndustryLine, this test pin comes from a supplier that positions itself as a quality filter for the European market. The combination of consistent component quality and direct supply from Emmerich supports reliable replenishment and integration into workshop tool fleets. For teams seeking practical assurance, the product fits the Metav approach of making high‑precision tools accessible and dependable for everyday industrial use. For workshop inspections or fixture integration, contact Metav Werkzeuge to discuss the M323.600 gauge pin and receive tailored advice from our technical consultants at the Emmerich site (info@metav-werkzeuge.com / +49 2822 7131930) Technical data SKU: M323.600 GTIN: 4061905058509 Product: Test pin, single, 6.00 mm, ±0.001 mm, length 50 mm Manufacturer: Metav IndustryLine Facts Diameter: 6.00 mm Tolerance: ±0.001 mm Length: 50 mm Weight: 0.014 kg Special features Material: special steel Workshop version Supplied in transport case for transport protection Intended for end measurement / reference checks FAQ What tolerance does this gauge pin offer? The Metav IndustryLine gauge pin M323.600 is specified at ±0.001 mm, making it suitable for high‑precision end‑dimension checks. Which applications suit this test pin? This test pin is designed for end measurements, plug checks and fixture reference use in workshop and production inspection tasks. Is the pin supplied ready for transport and storage? Yes — the gauge pin is supplied in a protective transport case to keep the component secure during handling and storage. What material is used and how durable is it? The M323.600 is made from special steel, selected for workshop durability and consistent dimensional stability under routine use. Can this pin be used for micro components or very small bores? With a diameter of 6.00 mm and very low tolerance, the pin is well suited to fine mechanical checks and small‑bore verification tasks. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
6mm Thread Gauge Set Metric/Whitworth 52-Piece For External And Internal Threads - Metav IndustryLine
Take advantage of the comprehensive 52-piece thread gauge assortment that combines metric and Whitworth standards for efficient production checks and rapid verification. The set’s wide coverage from 0.25–6.00 mm and 62–4 TPI supports consistent quality control across small threaded components; order the set directly via Metav Werkzeuge or ask the consultants for selection advice. Thread Gauge Set M318.002 — 52-piece Metric & Whitworth thread gauges (0.25–6.00 mm / 62–4 TPI) The Thread Gauge Set M318.002 is a compact, workshop-grade gauge assortment intended for fast verification of small-threaded parts in production, maintenance and inspection environments. 52-piece metric and Whitworth gauge set Covers 0.25–6.00 mm and 62–4 TPI Clear size marking for fast identification Compact, workshop-ready assortment Full coverage of small-thread standards for consistent checks The 52-piece assortment brings together both metric and Whitworth sizes in one compact set, covering a measuring range of 0.25–6.00 mm and the equivalent 62–4 TPI scale. This combination reduces tool changes when production involves mixed-thread components and simplifies incoming inspections where parts from different regions meet common specifications. The presented size range includes fine metric pitches and the commonly used Whitworth diameters, so thread conformity can be assessed directly at the workbench without additional conversion work. The clear distinction between the two standards speeds up decision-making during routine checks and keeps production moving. Rapid verification to improve throughput and reduce rework Designed for shop-floor use, the set enables quick tactile and dimensional checks that support established inspection routines and first-off approval procedures. Using a dedicated thread gauge set for go/no-go style verification shortens test time compared with measuring and calculating thread parameters, which makes process control more efficient. The metric side provides direct pitch and diameter references in millimetres, while the Whitworth side corresponds to threads per inch values; this duality helps maintain consistent results across diverse assemblies and reduces the risk of incorrect fittings or on-the-job rework. Practical benefits for quality assurance and inventory handling The compact assortment suits maintenance teams, toolrooms and quality departments that require a dependable reference for small threaded parts. Keeping the gauges together in a single set reduces the likelihood of missing sizes during checks and supports traceable inspection routines. When used as part of a regular control plan, the set contributes to reproducible verification of thread form and fit and therefore helps to avoid downstream failures. For procurement and inventory purposes, the set is supplied as a complete 52-piece kit, which simplifies stock keeping and ordering processes. For secure thread verification and fast delivery, contact Metav Werkzeuge to request the Metav IndustryLine Thread Gauge Set M318.002 or to discuss which sizes best suit specific inspection tasks — email info@metav-werkzeuge.com or call +49 2822 7131930 Technical data SKU: M318.002 GTIN: 4054469127583 Tariff number: 90173000 Core specifications Measuring range: 0.25–6.00 mm / 62–4 TPI Pieces per set: 52 Set type: Metric and Whitworth combined Contents & features Whitworth sizes (28): 4, 4.5, 5, 6, 7, 8, 9, 10, 11, 12, 13, 14, 16, 18, 19, 20, 22, 24, 25, 26, 28, 30, 32, 36, 40, 48, 60, 62 (55°) Metric sizes (24): 0.25, 0.30, 0.35, 0.40, 0.45, 0.50, 0.60, 0.70, 0.75, 0.80, 0.90, 1.00, 1.25, 1.50, 1.75, 2.00, 2.50, 3.00, 3.50, 4.00, 4.50, 5.00, 5.50, 6.00 (60°) Set configuration: complete assortment for small-thread verification Intended use: production checks, maintenance inspection, quality control FAQ What thread standards are included in the set? The set contains both metric and Whitworth gauges: metric sizes from 0.25–6.00 mm and Whitworth sizes covering the 62–4 TPI range, allowing direct verification of both systems. Is this set suitable for shop-floor verification? Yes, the Thread Gauge Set M318.002 is designed as a workshop-ready assortment for fast dimensional checks and routine inspection tasks. How many pieces are included and how are they organised? The kit comprises 52 pieces, divided into 24 metric gauges and 28 Whitworth gauges, supplied as a single, complete set for ease of inventory and use. Can the gauges be used for both internal and external thread checks? The supplied assortment covers the common sizes required for checking small threaded components; the set is intended for practical verification tasks in production and maintenance contexts. Which identifier should be used when ordering this set? Order references include the SKU M318.002 and GTIN 4054469127583 to ensure the correct 52-piece metric/Whitworth set is supplied. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
6mm Thread Gauges Set Metric And Whitworth 58 Pc, External/Internal - Metav IndustryLine
Take advantage of the combination of comprehensive thread coverage, compact portability and quick identification for reliable in‑process checks. Order the set directly via Metav Werkzeuge or consult our technical team for specification matching. Thread Gauge Set M318.003 — 58-piece metric & Whitworth set by Metav IndustryLine The Thread Gauge Set M318.003 provides compact, workshop-ready verification of common metric and Whitworth threads, ideal for routine incoming inspection and assembly checks. 58-piece metric and Whitworth coverage Covers 0.25–6.0 mm and common Whitworth pitches Compact, lightweight kit at 0.1 kg Fast go/no-go checks for production quality Comprehensive verification across metric and Whitworth systems This 58-piece gauge kit bundles a wide spread of sizes so that standard maintenance and quality‑control tasks are handled without repeated tool changes. The set spans 0.25–6 mm for metric threads and includes a range of Whitworth pitches, listed as both pitch and threads‑per‑inch where applicable, enabling immediate comparison between mating parts. The clear, consecutive sizing reduces selection time and supports faster fault diagnosis on the shop floor, contributing directly to uptime and process efficiency. Rapid, repeatable checks to speed up inspection routines Each individual gauge in the set is intended for quick go/no‑go verifications that remove ambiguity from tactile assessment. Using dedicated gauges for each size simplifies inspection steps and reduces interpretation errors compared with visual gauges alone. The compact format and lightweight nature make the kit suitable for carrying to workstations or storing at inspection benches, so thread verification becomes an integral, time‑saving part of routine quality procedures rather than a separate, disruptive task. Suited to workshop and production use with clear labelling The kit’s organised layout and labelling allow operators to identify the correct gauge quickly, which supports consistent use in serial production and assembly lines. Inclusion of both metric and Whitworth standards, along with common pipe thread sizes, means fewer supplementary tools are required to cover mixed‑standard inventories. The M318.003 set therefore helps to streamline tool inventories and supports reliable decisions during assembly, repair and incoming goods inspection. Contact Metav Werkzeuge today for tailored delivery from Emmerich and advice on integrating the M318.003 thread gauge set into existing inspection routines Technical Data Article number: M318.003 GTIN: 4054469127590 Tariff code: 90173000 Data Set pieces: 58 Weight: 0.1 kg Measurement range: 0.25–6 mm (metric) Whitworth pitches and TPI ranges included Special features Metric and Whitworth thread coverage Includes Whitworth pipe thread sizes Compact, transportable kit suitable for workshop use FAQ Which thread standards are included in the set? The thread gauge set contains both metric and Whitworth standards, with sizes and pitches listed for rapid identification and use with the M318.003 kit. What size range does the kit cover? The supplied gauges cover a 0.25–6 mm metric range and a selection of Whitworth pitches and common pipe thread sizes, allowing verification of many standard small‑to‑medium threads. Is the set suitable for production line checks? Yes, the M318.003 thread gauge set is designed for fast go/no‑go checks during incoming inspection and assembly, supporting repeatable decisions in production environments. How is the kit organised for use? The 58‑piece arrangement provides sequentially labelled gauges for quick selection; this layout helps to reduce inspection time and minimise selection errors with the M318.003 set. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
6–7mm Gauge Pin Set 100 Pieces 70mm Step 0.01mm, Special Steel, Supplied in Case - Metav IndustryLine
Take advantage of the combination of 0.01 mm graduation and a compact 6.00–7.00 mm measuring range to perform fast, repeatable inspection work; the set’s 70 mm shank length and special steel construction ensure durability and reliable handling on the shop floor. Order the set directly via Metav Werkzeuge or ask the consultants for application advice. M318.856 Gauge pin set — 6.00–7.00 mm, 0.01 mm graduation (Metav IndustryLine) The M318.856 gauge pin set is a compact inspection kit for fine hole and shaft gauging in precision workshops and quality departments. 0.01 mm graduation for fine inspection Range 6.00–7.00 mm in precise steps 70 mm shank length for deeper bores Special steel for long-term durability Delivered in protective transport case Precise, measurable inspection for small diameters The set is designed for repeatable dimensional checks across a 6.00–7.00 mm band with a 0.01 mm step size, enabling clear, quantifiable decisions during incoming inspection or in-process checks. Such a fine graduation supports fast go/no‑go assessment and incremental tolerance checks without complex fixtures; the numerical specification gives a direct basis for assessing conformity and documenting results. The compact diameter range places the kit in the workshop’s micro inspection category, where short, rigid test pins excel for minimal deflection and reliable contact. Robust handling and consistent contact force Each pin is manufactured from special steel, giving the package resistance to wear and mechanical damage under repeated use. The 70 mm shank length provides secure reach into deeper bores while retaining handling comfort and stiffness, reducing measurement uncertainty caused by pin bending. Storing the pins in a dedicated protective case preserves the set’s calibration condition and simplifies transport between bench and machine, supporting stable measurement routines and low lifecycle maintenance. Practical benefits for quality control workflows A complete set with incremental steps enables fast selection of the matching gauge pin for stepwise verification or fitting tasks, reducing setup time and increasing throughput in routine inspection cycles. The format is well suited to calibration benches, assembly jigs and portable inspection kits, and it integrates easily with existing documentation practices thanks to the clear numerical gradation. The robust material choice contributes to longer re‑service intervals, which lowers total cost of ownership and supports reliable sample testing over many cycles. Contact Metav Werkzeuge today in Emmerich to discuss how the Metav IndustryLine M318.856 gauge pin set can be integrated into existing inspection routines or to request tailored ordering information Technical data Article number: M318.856 GTIN: 4054469182087 Description: 100-piece gauge pin set, 6.00–7.00 mm range Weight: 3.43 kg Diameter range: 6.00–7.00 mm Pin length: 70 mm Graduation: 0.01 mm Material: Special steel Packaging: Protective transport case Category: Gauges (Lehren) Brand: Metav IndustryLine FAQ What diameter range is covered by the set? The M318.856 gauge pin set covers diameters from 6.00 mm to 7.00 mm in 0.01 mm increments for fine verification. How long are the pins and what does that mean for usability? Pins in this set are 70 mm long, which allows measurement into slightly deeper bores while maintaining rigidity and ease of handling. Is the set suitable for shop use and transport between workstations? Yes, the connectors are presented in a protective transport case so the pins remain organised and protected during routine movement around the workshop. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
6–7mm Gauge Pin Set 21-Piece 70mm Steps 0.05mm Plastic Case - Metav IndustryLine
Take advantage of the combination of repeatable accuracy, robust special-steel construction and a comprehensive 0.05 mm graduation for reliable bore verification in production and maintenance. Order the pin gauge set directly via Metav Werkzeuge or ask our consultants if needed. Pin Gauge Set M318.826 — 21-piece, 6.00–7.00 mm, 0.05 mm steps (Metav IndustryLine) the Pin Gauge Set provides a graduated selection of precision gauge pins for fast diameter checks and fit verification in toolrooms, production lines and maintenance workshops. Hardened special steel construction 0.05 mm graduated increments 70 mm gauge length for deep bores Precise diameter verification that speeds quality control Reliable inspection starts with clear reference values. The 21-piece gauge pin set covers the range 6.00–7.00 mm in uniform 0.05 mm steps, enabling rapid go/no‑go checks and stepwise narrowing to the required tolerance band. With each pin measured to consistent length (70 mm) and diameter grading, the set supports efficient inline and bench inspections, reducing rework rates and improving throughput. The combination of close graduations and full‑length pins makes it straightforward to confirm mating fits, seatings and bore wear without time‑consuming measurement set‑ups. Durable design for repeatable measurements Constructed from special steel and hardened for wear resistance, the pins maintain dimensional stability through repeated handling. The robust finish minimises surface damage that could otherwise alter the effective diameter during frequent use. This durability translates into long service life and consistent results during serial inspections or maintenance rounds. For shops that rely on reproducible measurements, robustness removes a common source of uncertainty and keeps quality checks practical over the long term. Improved workflow and reduced measuring uncertainty A graded set of 21 gauges helps technicians identify the correct fit quickly: coarse elimination followed by fine selection until the target clearance is achieved. The 0.05 mm step size is well suited to standard workshop tolerances, offering a balance between resolution and practical handling. Using gauge pins in sequence simplifies inspection protocols and shortens decision times compared with repeated micrometre adjustments. The set therefore supports faster cycle times while preserving measurement confidence. Versatile use across production, maintenance and toolmaking These pins are suitable for bore gauging, fixture checks, plug and sleeve verification, and fit testing on newly machined components. The compact set is ideal for toolrooms, jigs and fixtures, assembly stations and service departments where repeatable diameter checks are required. As a portable reference, the collection complements existing metrology tools and integrates easily into inspection routines, from routine maintenance to final quality sign‑off. The set is supplied by Metav IndustryLine and designed for pragmatic workshop use. Choose the Metav IndustryLine pin gauge set for dependable, workshop‑ready inspection and contact Metav Werkzeuge for specific delivery details and technical advice from Emmerich. Technical data Article number: M318.826 GTIN: 4054469181981 Manufacturer: Metav IndustryLine Weight: 1.06 kg Facts Measuring range: 6.00–7.00 mm Graduation: 0.05 mm Pieces per set: 21 Gauge length: 70 mm Special features Material: Special steel Hardened for wear resistance Sequential diameter grading for stepwise verification Suitable for bore and fit testing FAQ What diameters are included in the set? The set contains gauge pins covering 6.00–7.00 mm in 0.05 mm increments for systematic diameter checks. Can these pins be used for deep bore checks? Yes. With a 70 mm gauge length, the pins are suitable for many deeper bores and recessed checks where shorter pins would be impractical. What material are the pins made from? The pins are manufactured from special steel and hardened to provide wear resistance and stable dimensions under repeated use. How does the grading help in production environments? The 0.05 mm step size enables rapid elimination and fine selection during go/no‑go checks, shortening inspection times and improving throughput. Is this set suitable for toolroom and assembly checks? Yes. The 21-piece set is designed for toolrooms, maintenance and assembly lines where repeatable diameter verification is required. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
7 mm Ceramic Gauge Ball (Si3N4) 0.003 mm Accuracy, HV1400-1700 Hardness - Metav IndustryLine
Take advantage of exceptional dimensional stability and ultra‑low surface roughness to raise measurement reliability in gauges and fixtures; the compact 7 mm diameter and wear‑resistant Si3N4 construction ensure long service life with minimal drift. Order the component directly via Metav Werkzeuge or consult our specialists for application advice and availability. Ceramic Measuring Ball (Si3N4) 7 mm — 0.003 mm accuracy A Ceramic Measuring Ball (Si3N4) engineered for high‑precision gauging, calibration and reference use in metrology and inspection environments. Si3N4 ceramic, extremely wear-resistant Diameter tolerance 0.00008 mm Surface roughness Ra 0.00001 mm Precision that improves inspection reliability The 0.003 mm accuracy specification together with a diameter tolerance of 0.00008 mm makes this measuring sphere a dependable reference for repeatable inspections. Used as a reference element in gauge blocks, contact probes or as a master sphere in comparative checks, the component provides a stable datum that reduces measurement uncertainty. The compact geometry supports tight fixturing and minimises geometric error propagation when transferred into coordinate measuring machines or manual gauge setups. Durability and surface integrity for repeatable results Manufactured from Si3N4 ceramic and rated at HV1400–1700, the sphere offers high hardness and excellent wear resistance, preserving geometry under repeated contacts. The exceptionally low surface roughness Ra 0.00001 mm lowers friction and contact variation, which is especially beneficial for tactile probing and repeatability on low‑force measurements. The modest mass (approx. 0.08 kg) supports stable placement without excessive inertia, helping to maintain probe dynamics and reduce settling‑time influences during automated cycles. Practical integration into shop and lab workflows Designed for direct incorporation into gauge sets and inspection routines, the sphere complements standard gauging hardware and reference assemblies. Its small size enables precision work where space is restricted while still delivering metrology‑grade performance for batch inspection, fixture verification and routine calibration tasks. For specification matching and application guidance, Metav Werkzeuge’s technical advisers can clarify compatibility with existing probe systems and recommend handling best practice to preserve the reference surface. For precision applications, rely on Metav Werkzeuge’s supply chain and technical expertise—contact Metav Werkzeuge in Emmerich to confirm delivery options and integration advice for the Ceramic Measuring Ball (Si3N4) Technical data Article number: M318.437 GTIN: 4054469184371 Material: Ceramic (Si3N4) Core specifications Diameter: 7 mm Accuracy: 0.003 mm Diameter tolerance: 0.00008 mm Hardness: HV1400–1700 Weight: 0.08 kg Surface roughness Ra: 0.00001 mm Applications & features Category: Gauges / metrology Intended use: Reference and calibration tasks Ideal for CMM probing and tactile gauges Compact geometry for confined fixtures FAQ What measurement roles is this ceramic ball suitable for? The Ceramic Measuring Ball (Si3N4) is suited as a reference sphere for gauge blocks, probe calibration, comparative checks and other precision metrology tasks where 0.003 mm accuracy is required. Can the sphere be used with coordinate measuring machines (CMM)? Yes, the measuring sphere’s tight tolerance and low surface roughness make it compatible with CMM probing routines and tactile probe calibration, supporting consistent contact detection. Does the ball require special cleaning or handling? Maintain the sphere with lint‑free cloths and an appropriate, non‑aggressive cleaner; avoid abrasive media to preserve the Ra 0.00001 mm finish and minimise wear during handling. Is the component suitable for long‑term repeated contact in automated systems? The Si3N4 material and HV1400–1700 hardness provide high wear resistance for repeated probing cycles, helping to sustain dimensional stability over extended use. How is traceability provided for this part? The sphere is supplied with a clear article number (M318.437) and GTIN (4054469184371) for inventory control and traceability within inspection records. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
7 mm Go/No-Go Ring Gauge Wear Allowance, Hardened Steel, DIN 7162 - Filetta
Benefit from a hardened steel construction, DIN 7162 standard compliance and a wear‑compensated 'go' face for consistent inspection results; order through Metav Werkzeuge or request specialist advice for integration into quality workflows. Limit plug gauge, 7 mm — hardened steel, DIN 7162 (Filetta) A limit plug gauge designed for rapid verification of internal diameters in production and inspection environments, combining standard conformity with a wear‑compensated go face for sustained accuracy Hardened steel construction Conforms to DIN 7162 Precision 7 mm diameter Wear allowance on the go face Consistent inspection reliability for serial use The compact design supports routine checks where repeatability matters: the hardened construction and standardised geometry ensure that each measurement delivers the same reference result, reducing ambiguous outcomes on the shop floor. Used as a go/no‑go reference, this gauge streamlines acceptance steps and shortens inspection cycles, which helps to lower rework rates and maintain production throughput without additional setup time. Durable design that preserves accuracy over time A dedicated wear allowance on the go face protects the reference dimension and extends service intervals; the result is fewer replacements and more stable process capability. The hardened steel body resists deformation and abrasion in continuous use, so calibration intervals remain conservative and the tool sustains usable tolerances across many inspection cycles, supporting predictable maintenance planning. Simple integration into quality systems and traceable documentation Built to DIN 7162, the gauge fits established go/no‑go procedures and can be referenced directly in inspection plans. Its compact diameter of 7 mm makes it suitable for confined bores and tight features commonly encountered in precision components. Traceability is straightforward when the gauge is recorded in quality documentation, enabling clear pass/fail decisions during incoming, in‑process and final checks. Choose Filetta's hardened, DIN‑compliant limit plug gauge for robust, repeatable gauging and contact Metav Werkzeuge in Emmerich for tailored advice and ordering—email info@metav-werkzeuge.com or call +49 2822 7131930 for fast technical support and supply coordination Technical Data Article number: MS911.211 Material: hardened steel Standard: DIN 7162 Diameter: 7 mm Facts Product type: Limit plug gauge Brand: Filetta Intended use: Internal diameter verification Special features Wear allowance on the go face Suitable for production and inspection gauging Compact geometry for confined bores FAQ What applications suit this limit plug gauge best? This limit plug gauge is intended for quick verification of internal diameters in production, incoming inspection and routine quality checks where a 7 mm reference is required. How does the wear allowance affect service life? The wear allowance on the go face preserves the reference dimension, so the gauge maintains usable accuracy longer and reduces the frequency of replacements. Is the gauge compliant with recognised standards? Yes, the tool is manufactured to DIN 7162, which ensures compatibility with established go/no‑go procedures and inspection documentation. What is the material and why does it matter? Made from hardened steel, the gauge offers abrasion resistance and dimensional stability under regular use, supporting consistent pass/fail decisions. Manufacturer / Responsible: Schut Geometrische Meettechniek bv; Duinkerkenstraat 21; 9723 BN Groningen; The Netherlands; +31 50 5877877; schutnl@schut.com
7 mm Limit Ring Gauge H7 DIN 2245 Hardened Gauge Steel - Metav IndustryLine
Reliable verification through hardened gauge steel and DIN 2245 H7 tolerance delivers reproducible Go/No‑Go checks; benefit from robust wear resistance and rapid inline inspection. Order the limit plug gauge directly via Metav Werkzeuge or consult our advisors for application-specific guidance. Limit plug gauge M314.007 – 7.00 mm H7, DIN 2245 (Metav IndustryLine) The limit plug gauge M314.007 is designed for fast verification of H7 hole tolerances to DIN 2245 in production and inspection environments Hardened gauge steel construction DIN 2245 H7 tolerance standard Nominal diameter 7.00 mm Suitable for rapid Go/No‑Go inspection Faster, reproducible tolerance checks for serial production The M314.007 limit gauge enables immediate Go/No‑Go decisions at inspection points, reducing downstream rework and production delays. Thanks to the H7 tolerance specification to DIN 2245, the gauge gives a clear binary result that is quick to interpret and easy to document. Using a dedicated limit gauge instead of time-consuming measuring routines improves throughput while keeping quality control consistent across batches. The simple accept/reject logic supports lean workflows and helps maintain cycle times on high-volume lines. Robust construction that preserves accuracy under use Manufactured from hardened gauge steel, the plug gauge is engineered for wear resistance and dimensional stability over prolonged use. The chosen material reduces surface wear during repeated insertions, which contributes to long-term accuracy and predictable service intervals. Where tactile inspections are part of the routine, the hardened construction minimises adjustment drift and maintains the integrity of tolerance checks, making the gauge a practical choice for workshop and shop‑floor environments where reliability matters. Practical handling and clear specification for quality records Compact and unambiguous in its function, the limit plug gauge is intended for direct insertion checks and quick traceability in inspection reports. The nominal 7.00 mm size and the associated H7 rating make it suitable for standard bore checks in component production and maintenance tasks. As a simple, calibrated reference tool it complements dimensional measuring equipment by providing an immediate pass/fail indicator, which simplifies operator training and reduces interpretation errors in routine inspections. Contact Metav Werkzeuge today to request the Metav IndustryLine limit plug gauge M314.007 for dependable H7 checks and specialist advice on integrating gauges into inspection routines Technical data Article number: M314.007 GTIN: 4054469121369 eClass: 21170218 Standard: DIN 2245 Key measurements Diameter: 7.00 mm Tolerance class: H7 Tariff number: 90173000 Design and features Material: hardened gauge steel Category: Gauge pins; Gauges Condition: Good FAQ What tolerance and standard does this gauge check? The limit plug gauge checks hole tolerance H7 and is manufactured to DIN 2245, providing a standardised Go/No‑Go inspection reference. What material is the gauge made from and why does it matter? The gauge is made from hardened gauge steel, which offers improved wear resistance and helps preserve dimensional stability during repeated use. How is the gauge used in a production environment? The plug gauge is used for direct Go/No‑Go insertion checks on bores; the M314.007 provides immediate pass/fail results to support fast inspection cycles. Is this gauge suitable for inline or shop‑floor checks? Yes. The Metav IndustryLine M314.007 is intended for quick shop‑floor verification of H7 bores and integrates easily into routine inspection points. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
7 mm Setting Ring Form C Hardened Gauge Steel DIN 2250, JS3 - Metav IndustryLine
Combining a hardened, lapped gauge‑steel construction with DIN 2250 conformity, this 7 mm setting ring provides a stable reference for repeatable adjustments and inspection tasks; order the part directly via Metav Werkzeuge or request application advice from our consultants. Setting ring 7 mm — hardened, lapped gauge steel, DIN 2250 | Metav IndustryLine A Setting ring 7 mm designed as a precision reference gauge for workshop inspection, calibration and setting of internal measuring instruments in production and metrology environments Hardened, lapped gauge‑steel finish Conforms to DIN 2250 and DIN 286 JS3 tolerance for repeatable accuracy Compact 7 mm reference diameter Stable reference for reliable adjustment The ring is manufactured from hardened, lapped gauge steel, a finish that delivers long‑term wear resistance and dimensional stability. As a precision reference, the component serves to set and verify internal measuring tools and small inspection fixtures; the JS3 tolerance class and adherence to DIN 2250 and DIN 286 reduce uncertainty during comparative checks. This combination of material and specification supports reproducible results in routine shop‑floor calibration tasks, lowering rework rates and improving inspection throughput. Small diameter, big impact on process control With its 7 mm reference diameter and compact form, the ring is particularly suited to operations where a compact, robust master gauge is required. The small footprint allows easy integration into measuring benches and calibration rigs while maintaining the stiffness needed for precise contact measurements. Engineers benefit from the reduced handling complexity and consistent reference geometry, which simplifies setup sequences for gauge blocks, bore gauges and other internal measuring devices. Practical advantages for workshop use The component’s Form C configuration streamlines mounting and alignment in common inspection jigs. Lapping ensures a fine surface condition that minimises wear on both the ring and mating instruments, extending service life. The part is supplied as a ready‑to‑use reference item that fits directly into existing quality control routines, contributing to efficient inspection cycles and clearer pass/fail decisions. Quality assurance and procurement clarity Designed and listed under Metav IndustryLine, the component is documented with a clear article identifier and classification for procurement and inventory systems. The concise construction and standard conformity make it straightforward to include the ring in process documentation and traceable measurement procedures, supporting consistent quality standards across production batches. For precise setup and reproducible measurement routines, contact Metav Werkzeuge to request the M313.007 setting ring and expert application guidance — Metav’s team in Emmerich can advise on integration into existing inspection equipment Technical data SKU: M313.007 GTIN: 4054469120454 ECLASS: 21170104 Facts Diameter: 7 mm Tariff code: 90173000 Tolerance class: JS3 Special features Material: hardened, lapped gauge steel Standards: DIN 2250 and DIN 286 Configuration: Form C FAQ What is the primary use of this setting ring? The setting ring serves as a precision reference gauge for setting and checking internal measuring instruments; the M313.007 is intended for calibration and workshop inspection tasks. Which standards govern the ring’s accuracy? Accuracy and tolerance are specified to DIN 2250 and DIN 286 with a JS3 tolerance class for consistent reference measurement. Is the material suitable for repeated contact with measuring tips? Yes, the hardened, lapped gauge steel construction provides a durable surface that minimises wear on both the ring and contacting probes. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
7,09–10,01 mm Test Pin Set, 90 Pieces, Three-Point Selection 7,1–10 mm, 0,1 mm Steps, Special Steel, Case
Take advantage of the combination of precise dimensional coverage, robust construction and clear traceability to speed up inspection workflows and reduce rework. The 90-piece gauge pin set is supplied in a transport case and includes a dedicated pin holder for organised handling. Order the gauge pin set directly via Metav Werkzeuge or consult our technical team for application advice. M318.529 Gauge Pin Set — 90-piece, 7.09–10.01 mm, special steel (Metav IndustryLine) The M318.529 Gauge Pin Set is a precision test-pin kit for dimensional inspection, calibration and GO/NO‑GO checking in production and quality control environments 90-piece set, 7.09–10.01 mm range Special steel construction for long life Supplied with a pin holder for organisation Transport case for secure storage and transport Faster, repeatable inspection with lab-grade accuracy The set delivers a ±0.004 mm accuracy, offering a reliable baseline for pass/fail assessments and calibration tasks. With a comprehensive 7.09–10.01 mm measuring span available in small steps, routine checks become quicker and less error-prone. The precise sizing of the pins reduces setup time for gauging operations and supports consistent results across multiple operators, helping to cut down on rework and inspection cycles. Built for daily workshop use and durability Manufactured from special steel, the pins resist wear and maintain dimensional stability under regular use. The kit includes a dedicated pin holder that keeps individual gauges organised and a sturdy transport case to protect the contents during handling and storage. These features combine to preserve accuracy over time and make the set suitable for both the shop floor and the calibration bench. Clear increments and traceable tolerances for quality control Pins are supplied in 0.1 mm increments, enabling fine-grained measurement steps without ambiguity. The set also contains three-part offset variants (‑0.01 / 0 / +0.01) for defined tolerance checks, which simplifies GO/NO‑GO schemes and fitting trials. This deliberate configuration supports efficient quality plans and makes documentation straightforward when logging conformity against specified tolerances. Streamline inventory and rely on a European quality filter The compact kit format—90 pieces in a single set—reduces catalogue complexity and simplifies stock management. Supplied by Metav IndustryLine via Metav Werkzeuge, the product benefits from centralised quality control and a dependable logistics flow from Emmerich, which helps to safeguard supply reliability for production-critical measuring tools. This combination of supply assurance and measured performance supports robust manufacturing routines. Contact Metav Werkzeuge for tailored advice on integrating the Metav IndustryLine gauge pin set into existing inspection procedures; call +49 2822 7131930 or email info@metav-werkzeuge.com for detailed technical support and ordering. Technical data Article number: M318.529 GTIN: 4054469156156 Material: Special steel Pieces per set: 90 Measuring range: 7.09–10.01 mm Step size: 0.1 mm Accuracy: ±0.004 mm Weight: 5.6 kg Tariff code: 90173000 Core dimensions Range 7.09–10.01 mm Step 0.1 mm Accuracy ±0.004 mm Weight 5.6 kg Features & applications Includes pin holder Supplied in transport case Three-part tolerance variants (‑0.01 / 0 / +0.01) Set type: Gauge pins / test pins Suitable for inspection, calibration and GO/NO‑GO checks FAQ What tolerance can be expected from this gauge pin set? The M318.529 gauge pin set is specified with an accuracy of ±0.004 mm, providing tight, repeatable tolerances for inspection and calibration tasks. Is the set complete for standard dimensional checks in the 7–10 mm range? Yes, the 90-piece configuration covers the 7.09–10.01 mm span in 0.1 mm increments, including offset variants for defined tolerance checks. What material are the pins made from and how does that affect wear? Pins are made of special steel, chosen for dimensional stability and wear resistance to maintain long-term accuracy under regular use. Does the delivery include organisation and transport aids? The kit is supplied with a dedicated pin holder and a robust transport case to secure and organise the pins during storage and handling. Can this set be used for GO/NO‑GO checking and calibration trials? Yes, the configuration with 0.1 mm increments and three-part tolerances (‑0.01 / 0 / +0.01) is well suited for GO/NO‑GO schemes and calibration workflows. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
7-8mm Ceramic Gauge Pin Set 101 pcs 0.01mm Steps Plastic Case - Metav IndustryLine
High-precision, wear-resistant zirconia pins with HV 1250 hardness and an accuracy of < ±0.0015 mm ensure consistent inspection results; supplied complete in a plastic case with a probe pin holder, the set is available via Metav Werkzeuge for straightforward procurement or technical consultation. Zirconia Ceramic Gauge Pin Set, 101-piece (7.00–8.00 mm, 0.01 mm steps) — Metav IndustryLine The Zirconia Ceramic Gauge Pin Set is a workshop-grade verification tool for dimensional checks and plug testing across the 7.00–8.00 mm range, suited to metalworking and quality-control benches. Zirconia ceramic, non-magnetic and wear-resistant Accuracy better than ±0.0015 mm 0.01 mm graduations across 7.00–8.00 mm Supplied in plastic case with pin holder Reliable accuracy that reduces rework and rejects The set delivers laboratory-level accuracy of < ±0.0015 mm, making it suitable for fine tolerancing and repeatable inspection tasks in production and QA environments. The pins’ high hardness (HV 1250) resists indentation and wear, which preserves dimensional fidelity over extended use; this translates into fewer measurement-related reworks and increased process stability. With 0.01 mm graduations across the stated range, the pins provide predictable step increments for systematic checks and calibration transfers. Durable construction for daily workshop demands Manufactured from zirconia ceramic, the pins combine low friction with intrinsic corrosion resistance and non-magnetic behaviour, eliminating attraction-related measurement errors when working near magnetic materials. The workshop design is optimised for robustness: the wear-resistant surface and consistent geometry support frequent handling, while the included probe pin holder and plastic case protect the set during storage and transport. The overall result is a tool that maintains accuracy under harsh shop-floor conditions, reducing downtime for replacements. Practical format that integrates into inspection workflows Covering the narrow 7.00–8.00 mm span in fine steps, the pins are ideal for bore gauging, fit verification and component traceability tasks where short-range precision is required. Each pin has a 50 mm shank length, providing secure engagement in fixtures and allowing measurements in both bores and stepped features. The compact arrangement supports efficient inspection sequences and straightforward documentation of gauging results, so measurement routines remain fast and auditable without sacrificing precision. Contact Metav Werkzeuge for tailored advice or to request the M318.597 set for dependable workshop verification and inventory supply Technical Data Article number: M318.597 Manufacturer: Metav IndustryLine Name: Zirconia Ceramic Gauge Pin Set Facts Measuring range: 7.00–8.00 mm Graduation: 0.01 mm steps Pin length: 50 mm Hardness: HV 1250 Accuracy: < ±0.0015 mm Special features Material: Zirconia ceramic (wear-resistant, non-magnetic) Supplied in plastic case Supplied with probe pin holder Workshop version Set quantity: 101 pieces FAQ What material are the gauge pins made from? The pins are made from zirconia ceramic; the Zirconia Ceramic Gauge Pin Set from Metav IndustryLine uses this material for durability and non-magnetic performance. What is the stated accuracy of the set? Accuracy is specified as < ±0.0015 mm for the set, ensuring high repeatability during verification and control tasks. How are the pins supplied and stored? The set is supplied in a plastic case with a probe pin holder for organised storage and protection of the individual pins. What measuring range and graduations does the set cover? The pins cover the 7.00–8.00 mm range with 0.01 mm increments, suitable for fine plug and bore checks. Is the set suitable for use on magnetic assemblies? Yes; the zirconia ceramic material is non-magnetic, making the set appropriate for use near magnetic components without affecting measurements. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
7-8mm Gauge Pin Set 100 pcs 70mm Step 0.01mm Plastic Case - Metav IndustryLine
Combining 0.01 mm graduations, a robust special-steel construction and a 70 mm working length, this gauge pin set provides reliable, repeatable dimensional checks for production and inspection tasks; order directly via Metav Werkzeuge or consult our technical advisors for tailored advice. Metav IndustryLine Gauge Pin Set M318.857 — 7.00–8.00 mm, 0.01 mm increments The Gauge pin set M318.857 is a 100-piece inspection kit of 70 mm gauge pins designed for accurate plug gauging and go/no-go checks in workshop and quality-control environments. Precision steps of 0.01 mm Range 7.00–8.00 mm in 0.01 mm increments 70 mm length for stable insertion Special steel for wear resistance Supplied in a protective case Consistent dimensional verification with fine graduation The set delivers 0.01 mm graduations across the 7.00–8.00 mm range, offering dense incremental checks that simplify root-cause analysis of size variations in production. Tight graduation makes it possible to detect subtle tolerances and assess process drift without complex measuring equipment; the compact step size is particularly valuable when setting up small-bore features or when gauging fits where even a few micrometres matter. The design supports quick comparative checks, reducing the time between measurement and corrective action while preserving traceability in routine inspections. Robust material and handling for workshop use Manufactured from special steel, each pin balances surface hardness with corrosion resistance to withstand frequent insertion and withdrawal. The 70 mm working length improves guidance and stability within bore-type features, lowering the risk of angular misalignment during gauging. Practical benefits include longer service life and more consistent results under repeated use, which in turn reduces replacement cycles and downtime. For users without extensive metrology training, the straightforward nature of plug pins removes operator complexity: insert, check fit, and record result. Organised delivery that protects the set in transit The set is supplied in a protective case designed for transport and organised storage, which keeps the pins accessible and prevents surface damage that could compromise tolerances. The orderly arrangement accelerates selection during inspection routines and protects the inventory between shifts. Because the kit is pre-packaged for workshop conditions, it integrates well into toolbox systems or inspection benches and supports clear stock management for quality teams. Practical application and compatibility in production environments Ideal for small-bore inspection tasks, the kit suits machining, assembly and maintenance operations where repeated go/no-go checks are required. The dense 0.01 mm stepping is well-suited to quality-control loops that require frequent verification of mating parts and fit tolerances. As a straightforward gauging tool, the set complements more elaborate measurement systems by providing quick, reliable confirmation of compliance before parts progress to subsequent stages of production. Contact Metav Werkzeuge for expert advice on integrating the Metav IndustryLine gauge pin set into inspection routines and to arrange prompt delivery from Emmerich. Technical data Article number: M318.857 GTIN: 4054469182094 Brand: Metav IndustryLine Material: Special steel Range: 7.00–8.00 mm Graduation: 0.01 mm Length: 70 mm Pieces per set: 100 Weight: 4.03 kg Core specifications Measuring range minimum: 7.00 mm Measuring range maximum: 8.00 mm Step size: 0.01 mm Pin length: 70 mm Set count: 100 Net weight: 4.03 kg Special features Supplied in a protective case for transport Dense incremental gauging for fine adjustments Suitable for plug gauging and go/no-go checks Durable surface due to special-steel construction FAQ What is included in the gauge pin set M318.857? The Metav IndustryLine gauge pin set M318.857 includes a 100-piece range of plug pins covering 7.00–8.00 mm in 0.01 mm increments, supplied in a protective case for transport. Can these pins be used for daily go/no-go inspection in a workshop? Yes, the gauge pin set M318.857 is designed for routine go/no-go checks and short-cycle verification in production and maintenance settings. What material are the gauge pins made from and why does it matter? The pins are made from special steel, chosen for wear resistance and dimensional stability; this ensures longer service life and consistent inspection results. How long are the individual pins and what benefit does this provide? Each pin is 70 mm long, providing improved guidance and insertion stability for bore-type features, which helps reduce measurement error due to misalignment. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
7-8mm Gauge Pin Set 101 pcs, 0.01mm Steps, With Pin Holder, Special Steel, Supplied In Case - Metav IndustryLine
Product data contains inconsistent information and cannot be processed. The label specifies a 101-piece set ("101‑tlg."), while the item count field indicates 100 pieces (stuck_pro_satz = 100). This discrepancy creates confusion and prevents accurate processing of the product information. To ensure clarity and usability, it is essential to resolve this inconsistency by aligning the label and item count field. Please correct this discrepancy and provide consistent product data for a full product description. Accurate and consistent product information is crucial for proper documentation, inventory management, and customer understanding, so addressing this issue promptly is highly recommended.
7-8mm Gauge Pin Set 21-Piece 70mm Step 0.05mm, Special Steel in Case - Metav IndustryLine
Take advantage of precision, durable construction and convenient storage to speed up bore verification and quality checks; the compact design and 0.05 mm gradation support reliable repeatability in production. Order the gauge pin set directly via Metav Werkzeuge or contact the Metav team for advice. Gauge pin set M318.827 — 7.00–8.00 mm check pins with 0.05 mm steps (Metav IndustryLine) The Gauge pin set M318.827 is designed for precision checking of hole diameters and fits across the 7.00–8.00 mm range, offering reliable stepwise inspection for small bores in workshop and inspection environments. 21 precision pins in 0.05 mm increments Diameter range 7.00–8.00 mm Pins 70 mm long for through-hole verification Supplied in protective transport case Faster, repeatable checks for small bores A compact set of hardened pins provides a practical way to verify hole sizes with minimal setup time. The 0.05 mm gradation allows close incremental checks within the 7.00–8.00 mm band, so assessment of fit and clearance can be performed without complex gauges. Pins of 70 mm length reach deeper bores and ensure consistent engagement during verification; combined with the special steel construction, the set is built for wear resistance and sustained dimensional stability under regular use. Streamlined inspection routines for production and maintenance The set supports efficient sampling and routine inspection by enabling quick go/no‑go-style checks and staged measurements. Using a graduated collection of gauge pins reduces exchange time compared with single-size instruments, which improves throughput in repetitive tasks. The organised layout in the supplied protective case keeps each pin clearly identified, reducing handling errors and helping maintain traceability within workshop processes while supporting continuous production flows. Practical storage and workplace robustness Delivery in a transport case protects the pins from contamination and mechanical damage during storage or movement between workstations. The compact kit is suited to bench inspection, toolroom applications and maintenance tasks where compactness and clarity of measurement steps matter. The special steel composition gives a balance of hardness and toughness for industrial handling, and the complete set format simplifies inventory management for quality teams and fitters. Choose the Metav IndustryLine gauge pin set for workshop-ready precision and contact Metav Werkzeuge in Emmerich for specification advice or to arrange supply via info@metav-werkzeuge.com or +49 2822 7131930 Technical data Article number: M318.827 GTIN: 4054469181998 Weight: 1.2 kg Core specifications Diameter range: 7.00–8.00 mm Length: 70 mm Graduations: 0.05 mm Pieces per set: 21 Features / materials Material: special steel Supplied in a protective transport case Category: gauges (Lehren) Set format for staged diameter checks FAQ What diameter range does the set cover? The gauge pin set covers the 7.00–8.00 mm range with 0.05 mm increments for stepwise verification. How many pins are included and what are their lengths? The kit includes 21 pins, each 70 mm long, supplied in an organised protective case. What material are the pins made from? Pins are manufactured from special steel, selected for dimensional stability and wear resistance in workshop use. Is the set suitable for through-hole and deeper bore checks? Yes, the 70 mm pin length is intended to access through-holes and deeper bores for consistent verification. Can this set be integrated into routine quality control? The graduated pin collection and protective case make the set practical for routine inspection and sampling within production workflows. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
7.01-8mm Gauge Pin Set 100-Piece Step 0.01mm, Special Steel in Case - Metav IndustryLine
The 100-piece gauge pin set combines 0.01 mm graduation, a measurement range of 7.01–8.00 mm and special steel construction for repeatable bore checks and rapid tolerance sorting; organised transport is ensured by a protective case. Order the gauge pin set directly via Metav Werkzeuge or ask our consultants if needed. Gauge pin set M318.557 — 100-piece, 7.01–8.00 mm (0.01 mm steps) by Metav IndustryLine The gauge pin set M318.557 is a precision ground set of test pins ideal for fine-bore inspection, calibration and go/no-go verification in workshop and production environments *100-piece set with 0.01 mm graduation *Range 7.01–8.00 mm for fine tolerance checks *Supplied in protective transport case Repeatable inspection with micrometric steps Precision in dimensional control reduces rework and protects part quality. The pins in this set are supplied in 0.01 mm increments across the 7.01–8.00 mm span, permitting fine differentiation between nominal and out-of-tolerance conditions. A manufacturing tolerance of ±0.002 mm gives confidence when sorting or checking bores, while the regular step size simplifies decision-making during inspection routines. The incremental layout supports quick selection and minimises time spent measuring, so production checks can be completed faster and with fewer stoppages. Robust material and organised handling for daily use Constructed from special steel, the pins resist wear and maintain dimensional stability under routine contact use. The complete set is delivered in a protective transport case that keeps individual pins organised and prevents damage in transit or on the shop floor. With a total weight of 3.4 kg, the set is substantial enough for secure storage yet still convenient to move between workstations. These qualities reduce the need for frequent replacements and contribute to a lower total cost of ownership through longer service life. Practical benefits for quality control and process efficiency Fitted into inspection routines, a compact 100-piece set with fine gradation streamlines go/no-go verification, plug checks and quick comparative sizing without recurring setup. The clear gradation and stable material mean the set is well suited to repetitive tasks in toolmaking, small-bore assembly and maintenance shops. Traceable identifiers such as the SKU and GTIN facilitate inventory management and integration into procurement systems. The combination of repeatable accuracy and organised transport makes the set a pragmatic choice for workshops that require dependable, fast dimensional checks. For precise small-bore inspection and improved throughput, specify the Metav IndustryLine gauge pin set M318.557 and contact Metav Werkzeuge in Emmerich for delivery details or technical advice via info@metav-werkzeuge.com or +49 2822 7131930 Technical data Article number: M318.557 GTIN: 4054469129402 Material: Special steel Measurement range: 7.01–8.00 mm Graduation: 0.01 mm Pieces per set: 100 Facts Manufacturing tolerance: 0.002 mm Weight: 3.4 kg Pin length: 50 mm Tariff number: 90173000 Special features Supplied as a complete set for inspection and sorting Protective transport case for organisation and safety Precision ground pins Category: Gauge pins; Inspection gauges FAQ What sizes are included in the set? The set covers sizes from 7.01 mm to 8.00 mm in 0.01 mm increments, providing precise steps for fine tolerance checks. Is the material suitable for workshop use? Yes, the pins are made from special steel designed for wear resistance and stable dimensional performance in routine inspection tasks. Does the set include a case for transport and storage? A protective transport case is supplied with the set to keep pins organised and to prevent damage during handling. What accuracy can be expected from the pins? Manufacturing tolerance is 0.002 mm, which supports reliable repeatability for bore verification and sorting. Can the set be used for go/no-go checks and calibration routines? The graduated pins are suitable for quick go/no-go verification and comparative checks as part of regular calibration or inspection procedures. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
7.01mm Gauge Pin Length 50mm ±0.001mm Workshop Version - Metav IndustryLine
The nominal diameter of 7.01 mm combined with an ultra‑fine tolerance of ±0.001 mm and a 50 mm shaft delivers consistent end‑measurement results for workshop and inspection use. Supplied as a workshop execution component in a protective transport case, the item is available directly via Metav Werkzeuge — contact the consultants for specification advice or ordering. Gauge pin M323.701 — 7.01 mm, ±0.001 mm, 50 mm length (Metav IndustryLine) Gauge pin M323.701 is a single precision inspection pin designed for end‑measurements and plug gauge routines in workshop environments Nominal diameter 7.01 mm, tolerance ±0.001 mm 50 mm hardened shaft for consistent contact Special steel material for wear resistance Supplied in protective transport case Highest metrology accuracy to reduce process variance The core advantage of this inspection component is its measurement fidelity: a nominal diameter of 7.01 mm with a tolerance of ±0.001 mm provides a clearly defined acceptance window for final checks. In practice this means fewer ambiguous readings and faster go/no‑go decisions during incoming inspection or assembly verification, translating into less rework and more predictable throughput. The tolerance quoted reflects the manufacturing control of the pin and indicates its suitability where tight fit verification is required; this level of precision is commonly employed for tolerance stacks and end‑measurement checks in production lines. Rugged design for daily workshop handling Built as a workshop execution item from special steel, the pin balances surface hardness and corrosion resistance to withstand repeated seating into fixtures and gauges. At 50 mm length the shaft offers a secure gripping zone while minimising bending moment, and the overall mass (approx. 0.019 kg) keeps handling effortless during manual inspection cycles. Delivery in a protective transport case preserves the calibrated contact surfaces and reduces the risk of nicks or contamination in storage and transport, so the component arrives ready for immediate use on the bench or in a measuring jig. Easy integration into existing inspection routines The component is designed for straightforward use within standard gauge sets and plug gauge checks; its consistent geometry supports high reproducibility across repeated measurements and simplifies traceable documentation. Identified as M323.701 under the Metav IndustryLine, the pin can be incorporated into standard work instructions and measurement plans without modification to existing fixtures. For operations seeking to harmonise quality checks, this single inspection pin performs a clear role in end‑measurement tasks and helps stabilise quality gates at incoming inspection or final assembly. For workshop‑grade precision from Metav IndustryLine order the M323.701 gauge pin via Metav Werkzeuge or contact our consultants at info@metav-werkzeuge.com or +49 2822 7131930 for technical guidance and availability. Technical data Article number: M323.701 GTIN: 4061905060250 Material: Special steel Type: Workshop version Supplied in protective transport case Facts Nominal diameter: 7.01 mm Length: 50 mm Tolerance: ±0.001 mm Weight: 0.019 kg Special features Single gauge pin for end‑measurement High reproducibility for plug gauge checks Story trigger: end measurements FAQ What tolerance and diameter does this pin offer? The gauge pin M323.701 provides a nominal diameter of 7.01 mm with a tolerance of ±0.001 mm, suitable for precise end‑measurement applications. Is this item suitable for regular workshop use? Yes — produced as a workshop execution component from special steel and supplied in a protective transport case, the pin is intended for daily inspection and handling. What material is the pin made from and how does it affect wear? Constructed from special steel, the inspection pin offers a balance of hardness and surface integrity that improves wear resistance during repeated seating in gauges. Can the pin be used within plug gauge sets and measurement routines? The geometry and tight tolerance make the pin a reliable element for plug gauge checks and standardised inspection sequences in production and quality control. How is the product identified for ordering and traceability? The item is listed under Metav IndustryLine as M323.701 and carries the GTIN 4061905060250 for logistic and traceability purposes. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
Fast, tactile checks where electronics are impractical
Gauges and test pins provide unequivocal go/no-go results for threads, bores, gaps and radii without relying on electronics. The range covers plug gauges and ring gauges for internal and external threads, feeler gauges and precision feeler strips for micro‑gap assessment, plus probe pins and measuring pins for tactile diameter and pitch checks.
How these tools work in the production environment
Mechanical gauges operate as direct reference standards: a plug gauge or ring gauge verifies conformity to thread profiles and mating ability, while limit gauges separate accept from reject in a single step. Test pins are used to tactilely measure small bore diameters, centre‑to‑centre distances and radii. Manufactured from hardened gauge steel or ceramic and often precision lapped, these instruments deliver immediate physical results that are ideal for incoming inspection, machine‑side checks and final control.
Measurable benefits that affect production performance
- Reduced scrap and rework through rapid, unambiguous pass/fail assessment.
- Increased repeatability thanks to very low measurement uncertainty and fine lapping.
- Lower downtime: quick checks at the machine save cycle time and reduce setup periods.
- Durable construction with high wear resistance from specialised, low‑distortion alloys.
- Versatile delivery formats: individual gauges, organised sets in wooden cases or metre‑length feeler rolls compliant with DIN 2269.
Why Metav is the practical choice for precision supplies
Metav combines decades of expertise with a broad warehouse and quality filtering from Emmerich. As a precision partner for industry, craft and trade, Metav supplies a comprehensive selection of gauges and test pins alongside complementary tools such as precision calipers and setting rings. With over 48,000 customers and a catalogue exceeding 250,000 items, Metav is positioned to supply reliably, reduce vendor complexity and support traceable quality control to national standards.
Summary
Gauges and test pins are indispensable for dependable, repeatable quality assurance where tactile, mechanical verification is preferred. Choose these plug gauges, ring gauges, feeler strips and probe pins when immediate, robust measurement decisions are required on the shop floor.
FAQ
What materials are gauges and test pins typically made from?
Gauges and test pins are usually manufactured from hardened gauge steel for durability and wear resistance; ceramic variants are available where thermal stability and minimal wear are critical.
How do thread gauges ensure mating capability?
Thread plug gauges and ring gauges check flank diameters and thread form against standards, providing a clear go/no‑go verdict that confirms pairability with mating parts.
Which tolerance class should I choose for probe pins and gauge sets?
Select tolerance classes aligned with your inspection requirements; for high‑precision tasks, sets produced to DIN 2269 or equivalent tolerance classes ensure micrometre‑level control and repeatability.
Can feeler gauges measure contact gaps in valve and engine work reliably?
Yes. Feeler gauges and precision feeler strips, supplied either as a fan or metre‑length rolls, allow accurate assessment of valve clearances and contact gaps down to micrometre increments.
How do limit gauges speed up in‑process inspection?
Limit gauges separate good from bad in a single, tactile operation, enabling rapid go/no‑go checks at the machine and reducing both inspection time and the likelihood of human interpretation errors.
Fragen zu diesen Produkten??
Mit mehr als 30 Jahren Erfahrung beraten wir Sie gerne persönlich.
Tel.: +49 2822 7131930
Mail: info@metav-werkzeuge.com