Precision gauge blocks and plug gauges for reliable dimensional control
Mechanical gauge blocks and plug gauges are essential for tactile verification of threads, bores and gap dimensions, providing fast, unambiguous go/no-go results that enhance process reliability and reduce scrap. Designed for industrial metalworking and toolmaking, these precision tools support incoming inspection and final quality checks by delivering traceable measurements in applications such as thread inspection, bore diameter testing and spacing checks. Manufactured from specially hardened, low-distortion alloys and fine-lapped for minimal measurement uncertainty, the range includes thread plug gauges, precision plug gauges and calibration gauge blocks to ensure long-term repeatability and wear resistance.
8.05mm Gauge Pin Single, ±0.001mm Accuracy, 50mm Length, Workshop Version - Metav IndustryLine
Take advantage of the combination of ultra‑tight ±0.001 mm tolerance, robust special steel construction and an exact 8.05 mm nominal diameter for reliable end‑measurement control. Order the test pin directly via Metav Werkzeuge or consult our specialists for application advice. Test pin M323.805 — Single precision pin, 8.05 mm diameter, ±0.001 mm tolerance Test pin M323.805 is a single‑piece, workshop‑grade gauge pin designed for precise end‑measurement and go/no‑go checks in routine inspection tasks. Diameter 8.05 mm with ±0.001 mm tolerance Length 50 mm in workshop execution Made from special steel for long‑term wear resistance Single‑piece gauge for repeatable end measurements Exceptional accuracy that reduces rework and rejects The gauge pin delivers an accuracy of ±0.001 mm, which translates into measurable benefits on the shop floor: fewer false rejects, tighter process control and reduced rework. With a nominal diameter of 8.05 mm and a protected measuring length of 50 mm, the element is optimised for end‑measure verification and dimensional reference checks. The tight tolerance is particularly valuable where small clearances or interference fits are specified; replacing trial‑and‑error checks with a defined reference pin shortens setup times and improves batch consistency. Robust construction for continuous inspection use Manufactured from special steel, this single test pin is intended for repetitive use under workshop conditions. The material choice provides abrasion resistance and dimensional stability during repeated contact inspections, helping to maintain the original calibration state for longer. The workshop execution prioritises a compact, single‑piece design that is easy to handle and store alongside other inspection tools, making it suitable for in‑process checks and final acceptance tests on assemblies and components. Designed to integrate with inspection routines and traceability workflows As a precision end‑measurement tool, the pin supports standardised inspection procedures and simplifies documentation of conformity in serial production. The clear specification — 8.05 mm diameter, ±0.001 mm tolerance and 50 mm length — enables straightforward recording in quality logs and process sheets. The model M323.805 is suitable as a master reference in gauging fixtures or as a go/no‑go element for quick decisions at the bench, helping to maintain throughput while preserving measurement integrity. Choose the Metav IndustryLine test pin M323.805 for repeatable, workshop‑grade end‑measurement control — contact Metav Werkzeuge in Emmerich for ordering and application guidance Technical data Article number: M323.805 GTIN: 4061905059667 Weight: 0.024 kg Manufacturer: Metav IndustryLine Facts Nominal diameter: 8.05 mm Tolerance: ±0.001 mm Length: 50 mm Single‑piece gauge Special features Material: Special steel Workshop execution Application: end‑measurement / reference pin Category: Gauge pin / test pin FAQ What tolerance is guaranteed for this test pin? The test pin M323.805 is specified with a tolerance of ±0.001 mm for the nominal 8.05 mm diameter. Which material is used for the pin? The pin is manufactured from special steel, selected for wear resistance and dimensional stability during repeated inspections of components. For which inspection tasks is this pin suitable? The pin is intended for end‑measurement checks, reference gauging and quick go/no‑go decisions in workshop and production inspection routines. How is the test pin supplied? The product is supplied as a single gauge pin with a length of 50 mm and a clearly defined nominal diameter of 8.05 mm. Can this pin be used for serial production checks? Yes; the combination of robust material and tight tolerance makes M323.805 suitable as a repeatable reference for serial inspection tasks. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
8.06mm Gauge Pin ±0.001mm, 50mm Length, Workshop Version - Metav IndustryLine
Take advantage of workshop-grade precision and robust construction: the 8.06 mm diameter with a tight ±0.001 mm tolerance and a 50 mm length ensure reproducible end‑measure checks and reliable go/no‑go fitting. Order the gauge pin directly via Metav Werkzeuge or consult the technical team for specification support. M323.806 Gauge pin — Test pin, Ø 8.06 mm, ±0.001 mm, 50 mm length (Metav IndustryLine) The M323.806 Gauge pin is a workshop‑grade precision test pin designed for end‑measure verification and dimensional checking in production and inspection environments. Workshop‑grade precision instrument Diameter 8.06 mm ±0.001 mm tolerance Length 50 mm for deep bore checks Made from special steel for durability Consistent accuracy for critical tolerances The pin’s core advantage is its ±0.001 mm geometric accuracy, which supports repeatable pass/fail assessments and tight tolerance verification. Manufactured as a single‑piece test pin with a nominal diameter of 8.06 mm, the component is intended for applications where small deviations translate directly into assembly or functional faults. The exacting tolerance reduces inspection ambiguity and shortens decision cycles on part acceptance, helping to lower rework rates and maintain steady production throughput. Practical design that fits workshop routines With a 50 mm overall length and a compact mass of approximately 0.024 kg, this test pin is balanced for manual handling and fixture use alike. The special steel construction offers wear resistance in regular inspection routines and preserves the measurement surface over many cycles. The workshop execution of the product emphasises robustness without compromising dimensional stability, so the pin is suitable for repeated insertion into bores or for use as a reference mandrel in fixture checks. Simple integration into quality processes Traceability is supported by the clear article identifier (SKU M323.806) and GTIN, which simplify stock management and documentation. The gauge pin functions effectively as an end‑measurement reference in go/no‑go tests, assembly checks and periodic control routines; by providing a stable reference dimension, it streamlines inspection steps and contributes to faster, more reliable quality decisions on the shop floor. For workshop‑grade, traceable precision choose the Metav IndustryLine M323.806 gauge pin; contact Metav Werkzeuge in Emmerich for specification advice or to arrange supply: info@metav-werkzeuge.com / +49 2822 7131930 Technical data Article number: M323.806 GTIN: 4061905059674 Facts Diameter: 8.06 mm Length: 50 mm Tolerance: ±0.001 mm Weight: 0.024 kg Special features Material: special steel Workshop execution Suitable for end‑measure checks and go/no‑go fitting FAQ What is the primary application of this gauge pin? The M323.806 gauge pin is intended for end‑measure verification, go/no‑go tests and dimensional checking in production and inspection workflows. How tight is the dimensional tolerance? The test pin is specified to ±0.001 mm, making it suitable for high‑precision inspection tasks where minimal deviation is critical. What material is used for the pin and how does it affect durability? Constructed from special steel, the pin offers good wear resistance and surface stability during repeated insertion and fixture use. Can the pin be used in fixtures and assembly jigs? Yes, the compact 50 mm length and workshop‑grade build make the pin appropriate as a reference mandrel in fixtures and assembly checks. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
8.07mm Gauge Pin Single, ±0.001mm, 50mm Length, Workshop Version - Metav IndustryLine
Take advantage of high repeatability and robust workshop construction with the precision 8.07 mm gauge pin. With a ±0.001 mm tolerance and a 50 mm shank, this compact measuring pin ensures consistent end‑measurements and reliable fixture checks — order directly via Metav Werkzeuge or consult our specialists for application advice. Gauge pin M323.807 — 8.07 mm, ±0.001 mm, Metav IndustryLine The Gauge pin M323.807 is a workshop‑grade precision end‑measurement pin designed for repeatable go/no‑go checks, calibration tasks and setting fixtures in metalworking environments. High precision ±0.001 mm tolerance Diameter 8.07 mm for end‑measurement tasks Workshop‑grade special steel construction Supplied in a protective case for transport Micrometre-level repeatability for measurement assurance Engineered for demanding inspection routines, this gauge pin delivers ±0.001 mm repeatability that supports tight acceptance criteria in production and quality control. The nominal 8.07 mm diameter is held to the stated tolerance along the measuring length, reducing ambiguity when performing end‑face checks or verifying bore limits. In practice, such accuracy minimises false rejects and shortens inspection loops because a single unequivocal reference dimension replaces repeated comparative measurements. The result is a measurable increase in throughput and a more consistent quality record. Robust, workshop‑ready design that withstands daily use Built as a workshop‑grade tool from special steel, the pin combines wear resistance with manageable mass for handheld gauging and fixture insertion. A 50 mm shank length provides stable engagement and easy handling while remaining compact enough for tight jigs and gauges. The supplied protective case ensures secure transport between bench and production line, keeping the measuring face free from nicks that would compromise accuracy. Maintenance is straightforward: a clean, dry storage and occasional light lubrication preserve surface condition and dimensional integrity. Integrates simply into inspection and setup workflows The dimensional clarity of this gauge pin simplifies both manual checks and semi‑automated routines. The pin is suitable for fixture setting, end‑measurement verification and as a reference in comparator arrangements, helping to reduce setup time and rework. Traceability is supported by clear identification: SKU M323.807 and GTIN records can be logged alongside measurement records for audit trails. Where interchangeability and repeatable results matter, the pin shortens decision paths and supports consistent quality output with minimal operator training. Contact Metav Werkzeuge today to discuss how the M323.807 gauge pin fits into existing inspection routines — call +49 2822 7131930 or email info@metav-werkzeuge.com for tailored advice and supply from our Emmerich site Technical data Article number: M323.807 GTIN: 4061905059681 Manufacturer: Metav IndustryLine Label: Gauge pin, single, 8.07 mm, ±0.001 mm, length 50 mm Facts Diameter: 8.07 mm Length: 50 mm Tolerance: ±0.001 mm Weight: 0.024 kg Special features Material: special steel Version: Workshop execution Supplied in protective case Category: Gauge pins (Messstifte) FAQ What tolerance does the pin offer? The M323.807 gauge pin is specified to ±0.001 mm tolerance, providing micrometre‑level control for end‑measurement tasks. Is the pin suitable for fixture setting and go/no‑go checks? Yes — the workshop‑grade construction and precise 8.07 mm diameter make this gauge pin ideal for fixture setting, go/no‑go verification and calibration checks. What material is used for the pin and why does it matter? The pin is made from special steel, chosen for wear resistance and dimensional stability so that the measuring face remains reliable through repeated use. How is the pin delivered and protected? Delivery includes a protective case to prevent transport damage and maintain the measuring surface in workshop conditions. Can this pin be logged for traceability in quality records? Yes — use the SKU M323.807 and GTIN shown in the technical data for traceable documentation within inspection and audit systems. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
8.08mm Gauge Pin ±0.001 mm Length 50mm Workshop Version - Metav IndustryLine
Take advantage of high‑precision control with a diameter accuracy of ±0.001 mm and a compact 50 mm length for reliable end‑measurement references; order the gauge pin directly via Metav Werkzeuge or request advice from our consultants for specification guidance. Gauge pin M323.808 — 8.08 mm, ±0.001 mm tolerance, 50 mm length (Metav IndustryLine) Gauge pin M323.808 is a single inspection pin intended for dimensional verification and end‑measurement checks in precision work and small‑part inspection. Diameter 8.08 mm ±0.001 mm tolerance 50 mm length for secure handling and reference use Special steel for abrasion resistance and longevity Workshop‑grade finish for repeatable results Precision where micrometres decide The central asset of this inspection pin is its ±0.001 mm dimensional accuracy, which positions the component within the sub‑millimetre inspection class required for fine mechanical parts and close‑tolerance fits. With a nominal 8.08 mm diameter and a rigid 50 mm shaft, the pin serves as a dependable reference for end‑measure checks, alignment checks and comparative gauging. The tight tolerance reduces uncertainty in pass/fail assessments and supports reproducible measurements when used with micrometres, comparator rigs or fixture references. Robust construction for repeated reference use Manufactured from special steel, this workshop‑grade pin has been finished to provide stable contact surfaces during repetitive use. The 50 mm length offers a practical balance between grip and immersion depth for many inspection tasks, while the compact mass facilitates swift positioning and reduces the risk of flexing in hand or fixture. These material and dimensional choices translate into lower wear over repeated cycles and a steady measurement baseline that saves rework and downtime in small‑part inspection workflows. Practical integration into metrology workflows As an inspection device for end measurements and reference checks, the pin fits into standard inspection routines and fixture setups without complex adaptation. The product is identified as M323.808, making it straightforward to log in inventory systems or link to inspection protocols. Where control charts, batch testing or traceable documentation are required, the pin provides a stable datum that streamlines measurement comparability across shifts and machines. This combination of high repeatability and convenient form factor supports efficient quality control in small‑component assembly and toolmaking. Contact Metav Werkzeuge for specification advice and fast supply from Emmerich — our team will confirm suitability for your inspection setup and arrange immediate delivery from stock Technical data Article number: M323.808 GTIN: 4061905059698 Brand: Metav IndustryLine Core specifications Diameter: 8.08 mm Tolerance: ±0.001 mm Length: 50 mm Weight: 0.024 kg Features and materials Material: special steel Intended use: end measurement / inspection pin Version: workshop execution Category: gauge pin / inspection pin FAQ What level of accuracy does this inspection pin provide? The gauge pin M323.808 delivers an accuracy of ±0.001 mm, suitable for sub‑millimetre inspection tasks where micrometre‑level distinction is required. Is the pin suitable for repeated use in workshop measuring fixtures? Yes. The special steel construction and workshop version finish of the M323.808 are designed for repeated reference use in fixtures and small‑part inspection. Can this pin be used with micrometres and comparator systems? The 8.08 mm diameter and 50 mm length make the M323.808 compatible with micrometres, comparator setups and bespoke fixture arrangements for end‑measurement checks. Which applications are typical for this inspection pin? Applications include dimensional verification of small bores and shafts, alignment reference in assembly fixtures, and comparative checks in toolmaking and component inspection. How is the product identified for ordering and documentation? The product is listed as M323.808 under the Metav IndustryLine range and carries GTIN 4061905059698 for traceable documentation. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
8.09mm Gauge Pin Single, ±0.001mm, 50mm Length, Workshop Version - Metav IndustryLine
Benefit from micrometre-level control and robust workshop design: the gauge pin combines ±0.001 mm dimensional accuracy with a stable 50 mm length for repeatable end-dimension checks; order the part directly via Metav Werkzeuge or consult our advisers for application support. Gauge pin M323.809 — single gauge pin, Ø 8.09 mm, ±0.001 mm accuracy (Metav IndustryLine) A single gauge pin M323.809 designed for precise end-dimension inspection and reference measurements in workshop and inspection settings Workshop version construction Tolerance ±0.001 mm Ø 8.09 mm precision diameter Length 50 mm for stable handling Micrometre-level final-dimension control for reliable quality assurance The instrument delivers an ultra-fine tolerance of ±0.001 mm (one micrometre), which places it in the class of high-precision gauge tools suitable for final-dimension verification. Such accuracy reduces uncertainty when checking bore or pin fits, enabling reproducible pass/fail decisions during incoming inspection or final assembly. The tight tolerance is particularly beneficial where small clearance margins determine functional performance, and it supports objective measurement protocols that improve production yield. Robust workshop design that makes measurements repeatable Manufactured in special steel and specified as a workshop version, the pin offers a hard-wearing contact surface and dimensional stability over repeated cycles. The 50 mm shank provides secure gripping and reduces the effect of fingertip torque during handling, while the Ø 8.09 mm nominal diameter ensures compatibility with common reference fixtures and gauges. This combination of material choice and geometry translates to fewer measurement variations and a dependable reference for shop-floor and QC processes. Practical inventory and application benefits for production environments As a single reference gauge for end-dimension checks, the part is compact to store and easy to integrate into existing inspection routines. The clear article identifier (SKU M323.809) and GTIN support straightforward stockkeeping and traceability within a quality-management system. Choosing the Metav IndustryLine variant aligns a workshop with a provider that emphasises reliable supply and accessible precision tools, which helps to simplify purchasing decisions and to maintain continuous production uptime. Secure micrometre accuracy with the Metav IndustryLine gauge pin — contact Metav Werkzeuge in Emmerich at info@metav-werkzeuge.com or +49 2822 7131930 for specification matching and supply assistance Technical data Article number: M323.809 GTIN: 4061905059704 Eclass: 21170231 Label: Gauge pin, single, 8.09 mm, ±0.001 mm, length 50 mm Facts Diameter: 8.09 mm Length: 50 mm Tolerance: ±0.001 mm Weight: 0.024 kg Special features Workshop version Material: special steel Intended use: end-dimension checks Single gauge pin FAQ What tolerance does this gauge pin offer? The gauge pin M323.809 provides a tolerance of ±0.001 mm, suitable for micrometre-level inspection and fine tolerance verification. Which material is the pin made from? The pin is manufactured from special steel, specified for workshop durability and stable contact surfaces. For which applications is this pin intended? This single gauge pin is intended for end-dimension checks, reference measurements and bore verification in workshop and inspection environments. How is the item identified for inventory? Identification is via the SKU M323.809 and GTIN 4061905059704, supporting traceability and stockkeeping. Is the design suitable for repetitive shop-floor use? Yes—its workshop version design and 50 mm length provide robust handling for repeated measurements with reduced variability. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
8.11mm Gauge Pin Single, ±0.001mm Accuracy, Length 50mm, Workshop Version - Metav IndustryLine
The precise ±0.001 mm tolerance and the compact 8.11 mm diameter with a 50 mm length make this inspection pin a reliable choice for repeatable end‑measure checks; coupled with a robust special steel construction it supports consistent workshop workflows — order the M323.811 gauge pin directly via Metav Werkzeuge or consult our technical advisers for application-specific recommendations. M323.811 Gauge pin – 8.11 mm, ±0.001 mm, 50 mm length (Metav IndustryLine) M323.811 is a single precision gauge pin designed for end‑measure inspection and tooling verification in workshop environments Workshop execution, durable design High precision ±0.001 mm tolerance Diameter 8.11 mm, usable length 50 mm Accuracy that secures process reliability The remarkably fine ±0.001 mm tolerance of this inspection pin ensures reproducible checks of end measures and finished bores, reducing the risk of unnoticed deviations in serial production. With such a narrow tolerance band, the pin serves as a deterministic reference for go/no‑go checks and comparative inspection routines, enabling clear pass/fail decisions and supporting quality control processes that demand traceable dimensional certainty. The compact mass also minimises thermal drift during short inspection cycles. Compact geometry for tight spaces and fixture checks The slender 8.11 mm diameter and 50 mm length create a geometry that is easy to handle in confined setups and practical for fixture alignment or plug‑type measurements. The low mass (approx. 0.025 kg) improves manual positioning and reduces the influence of inertia when gauging small components. In workshop contexts where accessibility and repeatability matter, this inspection pin functions effectively as a plug gauge, mandrel or reference dowel for quick verification of bores, seats and end faces. Material choice and workshop suitability Manufactured from special steel and supplied in a workshop execution, the pin is built for regular use under production conditions. The material selection aims to provide a stable contact surface and wear resistance appropriate for routine inspection tasks without overstating performance beyond the provided data. As a single‑piece inspection tool with industrial design, it integrates well into standard measurement benches and manual gauges, contributing to dependable measurements across repetitive inspection steps. Consider Metav IndustryLine’s M323.811 gauge pin when precise end‑measure verification is required; order via Metav Werkzeuge for a reliable supply from Emmerich and request application advice from our specialists if needed Technical data SKU: M323.811 GTIN: 4061905060519 Brand: Metav IndustryLine Label: Prüfstift, einzeln, 8,11mm, +/- 0.001 mm Länge 50 mm Facts Diameter: 8.11 mm Tolerance / Accuracy: ±0.001 mm Length: 50 mm Weight: 0.025 kg Special features Material: Special steel Workshop execution Category: Gauge pins (Messstifte) Application hint: end‑measure inspection FAQ What is the measurement tolerance of the M323.811 gauge pin? The M323.811 gauge pin is specified with a tolerance of ±0.001 mm, making it suitable for fine inspection tasks that require high repeatability. For which inspection tasks is the M323.811 gauge pin suitable? The M323.811 gauge pin is intended for end‑measure checks, bore verification and fixture alignment in workshops and production lines where compact reference pins are required. Is a calibration certificate supplied with the M323.811 gauge pin? The product data for the M323.811 gauge pin does not specify a calibration certificate; calibration status is not listed in the available information. What material is used for the M323.811 gauge pin? The M323.811 gauge pin is made from special steel, chosen for stable contact properties appropriate to routine workshop inspection. How should the M323.811 gauge pin be handled and stored? Handle the M323.811 gauge pin with clean hands or gloves to avoid contamination; store in a dry, stable environment away from corrosive agents and heavy impacts to preserve dimensional accuracy. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
8.12mm Test Pin ±0.001mm Length 50mm Workshop Version - Metav IndustryLine
Take advantage of the combination of ultra‑fine accuracy, robust workshop execution and traceable identification for reliable end‑measurements; order the gauge pin directly via Metav Werkzeuge or consult our specialists for batch supply. Gauge pin M323.812 — single 8.12 mm, ±0.001 mm accuracy (Metav IndustryLine) A single gauge pin, the M323.812, engineered for high‑precision end measurements in workshop and inspection applications. Single gauge pin 8.12 mm, tolerance ±0.001 mm Length 50 mm for stable insertion and positioning Made from special steel for wear resistance Workshop execution for robust daily use Accuracy that secures acceptance in production The M323.812 delivers ±0.001 mm positional accuracy, a level that reduces measurement uncertainty in go/no‑go checks and end‑measurement tasks. Such precision is especially valuable where small tolerances decide part acceptance; the fine tolerance minimises rework and supports faster quality decisions. Measured performance is ideal for precision jigs, fixture checks and final inspection steps, improving throughput without compromising traceability. Robust design for repeatable handling on the shop floor With a 50 mm length and a nominal 8.12 mm diameter, this single gauge pin balances insertion stability and accessibility in assemblies. The special steel construction resists surface wear under repeated use, which preserves dimensional integrity over many cycles. The workshop execution prioritises reliable handling: chamfered ends for easy entry, a smooth bearing surface for consistent seating and a compact mass of approximately 0.025 kg for convenient storage and transport. Workflow benefits: faster checks and fewer disputes Using a standardised precision pin reduces downtime during inspection and simplifies acceptance criteria between suppliers and production. The clearly defined 8.12 mm nominal size and micron‑level tolerance allow integration into automated gauge blocks, fixture audits and manual go/no‑go sequences. The compact form factor supports rapid interchange in multi‑station fixtures, helping to maintain cycle time while offering measurable improvements in first‑pass yield. Contact Metav Werkzeuge for supply and technical advice on the M323.812 single gauge pin and secure consistent measurement performance across production lines Technical Data SKU: M323.812 GTIN: 4061905060526 Manufacturer: Metav IndustryLine Facts Diameter: 8.12 mm Length: 50 mm Tolerance: ±0.001 mm Weight: 0.025 kg Special features Single gauge pin, workshop execution Material: special steel Designed for end‑measurement and fixture checking Suitable for repeated insertion checks FAQ What tolerance does this gauge pin offer? The M323.812 gauge pin is specified to ±0.001 mm, suitable for micron‑level end measurements and tight acceptance checks. Is the gauge pin suitable for repeated workshop use? Yes, the workshop execution and special steel material make the pin robust for frequent insertion and inspection cycles. How is the M323.812 typically applied in inspection workflows? It is used for go/no‑go checks, fixture alignment and end‑measurement verification where a precise fixed diameter establishes conformity. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
8.13mm Gauge Pin, Single, ±0.001mm Accuracy, 50mm Length, Workshop Version - Metav IndustryLine
Benefit from workshop‑ready precision: the compact design combines a precise Ø 8.13 mm gauge with an exceptionally tight ±0.001 mm tolerance and a practical 50 mm length for reliable end‑measure checks. Order the part directly via Metav Werkzeuge or ask our consultants for application advice. Gauge pin M323.813 — Single test pin, Ø 8.13 mm, ±0.001 mm (Metav IndustryLine) Gauge pin M323.813 — a single precision test pin for dimensional checking and end‑measure verification in workshop metrology Precision diameter 8.13 mm, tolerance ±0.001 mm 50 mm hardened special steel Workshop execution for robust use Supplied in protective case Repeatable accuracy for production checks The compact test pin delivers high repeatability by combining a precisely ground 8.13 mm diameter with a fine ±0.001 mm manufacturing tolerance — a level of precision that supports tight acceptance limits in component inspection. Thanks to the special steel construction and workshop‑grade finish, the pin sustains surface integrity under regular use, which reduces the risk of measurement drift during routine checks. This makes it an effective tool for end‑measure verification, jig alignment and short‑range plug‑gauging tasks without introducing unnecessary handling complexity. Robust design that suits everyday workshop use Built as a workshop execution component, the pin withstands mechanical handling typical in busy production areas. The 50 mm length balances reach and rigidity so that measurements remain stable while handling is simple and secure. The compact weight and form factor support fast interchangeability in inspection routines; when stored in the supplied protective case, the risk of accidental damage or contamination is minimised, prolonging service life and preserving the calibrated geometry where present. Clear specifications to integrate into inspection routines The plain geometry and narrow tolerance make this test pin straightforward to document in control plans and measurement procedures. The simple shape supports rapid visual inspection and easy cleaning; when used as a reference element in fixtures or measuring jigs, the consistent diameter and hard material reduce wear on mating components. For quality managers and workshop technicians, the combination of ±0.001 mm tolerance and compact length provides a reliable reference that complements go/no‑go gauges and small bore inspection tools without adding complexity. Discuss application suitability and delivery options for the Metav IndustryLine gauge pin M323.813 with Metav Werkzeuge to ensure the right fit for workshop inspection needs. Technical data SKU: M323.813 GTIN: 4061905060533 Material: Special steel Diameter: 8.13 mm Tolerance: ±0.001 mm Length: 50 mm Weight: 0.025 kg Facts Diameter: 8.13 mm Length: 50 mm Tolerance: ±0.001 mm Weight: 0.025 kg Special features Single test pin Workshop execution Supplied in protective case Category: Gauge pins Intended for end‑measure and dimensional checks FAQ What is this pin typically used for? The Metav IndustryLine gauge pin M323.813 is intended for dimensional checking, end‑measure verification and short‑range plug‑gauging in workshop metrology. Does the product include a calibration certificate? The available product data does not specify an included calibration certificate for the M323.813 gauge pin. What material is the pin made from? The pin is manufactured from special steel, chosen for wear resistance and dimensional stability in workshop conditions. How tight is the manufacturing tolerance? The gauge pin is produced to a tolerance of ±0.001 mm, suitable for fine inspection tasks and tight acceptance criteria. Is the pin delivered ready for safe storage and transport? Yes, the workshop execution variant of the M323.813 is supplied in a protective case to reduce the risk of damage during storage and transport. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
8.14mm Gauge Pin, ±0.001mm Accuracy, 50mm Length, Workshop Version, Special Steel, Supplied in Case - Metav IndustryLine
Take advantage of the combination of workshop-grade construction, micrometric ±0.001 mm accuracy and a compact 50 mm length for reliable end-dimension checks and setting tasks. Order the gauge pin directly via Metav Werkzeuge or consult the product specialists if further clarification is required. Gauge pin M323.814 – single pin, Ø 8.14 mm, ±0.001 mm (Metav IndustryLine) Gauge pin M323.814 is a single, high-precision checking pin for dimensional verification and fixture setting in workshop metrology *High-precision ±0.001 mm tolerance *Diameter 8.14 mm for tight fits *50 mm length for standard setting tasks *Workshop-grade special steel construction Keep production within narrow tolerances The M323.814 is designed for applications where dimensional certainty prevents rework and scrap. With a certified manufacturing tolerance of ±0.001 mm, this single gauge pin enables extremely fine go/no‑go checks and precise reference measurements for final part control. The 8.14 mm diameter serves as a reliable datum for end-dimension verification, helping to maintain consistent production quality and reducing the need for corrective machining. Built for everyday workshop use Labelled as a workshop execution, the pin combines compact dimensions with robust material selection to cope with routine handling. The body is manufactured from special steel, offering a balance between wear resistance and dimensional stability under normal workshop conditions. The 50 mm length provides enough engagement for setting and verification tasks while remaining easy to handle and store. The single-piece supply simplifies inventories where individual replacement pins are required. Simple identification and integration into stock systems Procurement and inventory control are simplified by clear identifiers and compact data: SKU M323.814 and GTIN 4061905060540 enable straightforward ordering and stock tracking. The compact mass (approximately 0.025 kg) permits efficient storage and fast picking for assembly lines or inspection benches. As an end-dimension checking tool, this pin is particularly suited to repeat checks, fixture setup and quick in-process verifications where traceable, repeatable references are required. Choose the Metav IndustryLine gauge pin for reproducible end-dimension measurements and contact Metav Werkzeuge in Emmerich for procurement or technical advice Technical data Article number: M323.814 GTIN: 4061905060540 eClass: 21170231 Facts Diameter: 8.14 mm Length: 50 mm Tolerance: ±0.001 mm Weight: 0.025 kg Special features Material: special steel Single item, workshop execution High-precision manufacturing FAQ What is the primary use of this gauge pin? The gauge pin M323.814 is intended for precise dimensional verification and fixture setting, serving as a reference for end-dimension and go/no‑go checks. How accurate is the pin and what does that mean for production? With a tolerance of ±0.001 mm, the pin provides micrometric accuracy that reduces measurement uncertainty and supports tight production tolerances. Which materials and tasks suit this gauge pin? The pin is a general-purpose checking tool for workshop metrology tasks such as setting, verifying bore fits and repeat inspections on metal and machined components. How does the construction reflect workshop requirements? The workshop-grade special steel construction and compact 50 mm length balance durability with ease of handling for routine inspection and setting tasks. How is the product identified for ordering and stock control? Identification is via SKU M323.814 and GTIN 4061905060540, which streamlines procurement and inventory management Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
8.15mm Gauge Pin, Single, ±0.001mm Accuracy, 50mm Length, Workshop Version - Metav IndustryLine
Take advantage of the pin's ultra‑fine tolerance and robust workshop design to secure reproducible end‑measurements with minimal setup time; the gauge pin's ±0.001 mm accuracy and 50 mm length ensure reliable fit testing across production runs. Order the single inspection pin directly via Metav Werkzeuge or consult the Metav team for specification matching. M323.815 Gauge pin — 8.15 mm, ±0.001 mm (Metav IndustryLine) The M323.815 is a single gauge pin for precision end‑measurements and go/no‑go checks in workshop and inspection environments. Workshop version for robust daily use Diameter 8.15 mm with ±0.001 mm accuracy Length 50 mm for precise end measurements High‑precision control that reduces rework Designed for inspection tasks where dimensional certainty matters, this gauge pin offers ±0.001 mm (1 µm) tolerance to support tight acceptance criteria. Such fineness of control reduces the need for repeated adjustments and downstream rework, improving throughput in small‑batch and serial production alike. The pin acts as a reliable reference for plug and bore checks, helping to validate assembly fits and final tolerances without complex fixtures. Built for everyday handling in industrial workshops The workshop configuration combines a hardened special steel construction with a compact 50 mm length to balance stiffness and manoeuvrability. The robust finish resists typical wear encountered during daily use, while the single‑piece design simplifies storage and selection in inspection trays. Delivery includes a protective case for safe transport and handling, preserving the measuring surface between uses. Practical benefits: quick checks, consistent results With an exact diameter of 8.15 mm, the pin supports repeatable go/no‑go assessments and end‑mass verifications across batches. The simple geometry minimises handling variance, so measurement routines can be standardised on the shop floor and integrated into quality control procedures. Traceable dimension conformity shortens inspection cycles and provides a dependable reference for assembly checks. Contact Metav Werkzeuge for tailored advice on integrating the Metav IndustryLine M323.815 gauge pin into inspection routines; call +49 2822 7131930 or email info@metav-werkzeuge.com to confirm suitability and availability Technical data Article number: M323.815 GTIN: 4061905060557 Label: Prüfstift, einzeln, 8,15mm, +/- 0.001 mm Länge 50 mm Facts Diameter: 8.15 mm Length: 50 mm Tolerance: ±0.001 mm (1 µm) Weight: 0.025 kg Special features Material: Special steel Workshop execution for everyday use Delivered in protective case for transport Single inspection pin for end measurements Category: Gauge pins (Messstifte) FAQ What inspections is this gauge pin suited for? The M323.815 gauge pin is intended for end‑measurements, plug and bore checks and go/no‑go verifications where a precise 8.15 mm reference is required. Is the tolerance of ±0.001 mm sufficient for bore acceptance testing? Yes, the ±0.001 mm tolerance of this inspection pin provides sub‑micrometre precision suitable for tight acceptance criteria and fine fit validation. What is the material and how does it affect wear resistance? The pin is made from special steel, chosen for durability and resistance to wear encountered during frequent insertion and removal. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
8.16mm Gauge Pin Single ±0.001mm Length 50mm, Workshop Version - Metav IndustryLine
Take advantage of the combination of ultra‑fine accuracy and robust workshop design for reliable end‑measurement tasks; order directly via Metav Werkzeuge or consult our specialists for application advice. Gauge pin M323.816 — 8.16 mm, ±0.001 mm, 50 mm length (Metav IndustryLine) The Gauge pin M323.816 is a single precision reference pin intended for end‑measurement checks and go/no‑go reference tasks in machine workshops and inspection benches Single gauge pin, 8.16 mm nominal diameter High precision: ±0.001 mm tolerance Length 50 mm, workshop version Supplied in transport box for protection Accurate reference for tight tolerances The Gauge pin M323.816 delivers an 8.16 mm nominal diameter with an exceptional ±0.001 mm tolerance, providing a trusted reference for end‑measurement and dimensional verification. The fine tolerance reduces measurement uncertainty and shortens inspection cycles by eliminating repeat checks. As a hardened reference element made from special steel, the pin maintains its geometry under regular handling, which supports consistent pass/fail decisions in quality control and helps to secure process reliability in production environments. Built for shopfloor durability and repeatability Designed as a workshop version, the pin withstands frequent use while preserving the contact geometry required for reproducible results. The 50 mm length gives sufficient working engagement for many end‑measurement scenarios without adding unnecessary mass; its low mass (approx. 0.025 kg) makes handling and fixture placement straightforward. Delivery in a transport box protects the gauge during storage and transit, reducing the risk of nicks that would compromise accuracy and thus lowering lifecycle costs through prolonged serviceability. Practical integration into inspection routines The compact form of this precision pin simplifies incorporation into inspection jigs, pin blocks and alignment setups, enabling faster routine checks and reduced setup time. Traceable identification (SKU M323.816 / GTIN 4061905060564) simplifies stockkeeping and quality documentation. Using a calibrated reference element with such fine tolerance supports tighter process control and helps to avoid downstream rework, improving throughput and preserving component integrity. For assured end‑measurement performance, contact Metav Werkzeuge to discuss the Metav IndustryLine gauge pin and its suitability for specific inspection tasks or to request procurement support from our Emmerich team Technical data Article number: M323.816 GTIN: 4061905060564 Manufacturer: Metav IndustryLine Facts Diameter: 8.16 mm Tolerance: ±0.001 mm Length: 50 mm Weight: 0.025 kg Measurement range min/max: 8.16 mm Special features Material: Special steel Workshop version Supplied in transport box for transport protection Category: Gauge pins (Messstifte) Story trigger: end measurements FAQ What nominal diameter does this gauge pin have? The Gauge pin M323.816 has a nominal diameter of 8.16 mm. What is the stated tolerance for this gauge pin? The tolerance is ±0.001 mm, making the pin suitable for very fine end‑measurement references. How long is the pin and how is it packaged? The pin is 50 mm long and is supplied in a transport box to protect the measuring faces during storage and transit. What material is used for the gauge pin? The pin is manufactured from special steel, selected for dimensional stability and wear resistance in workshop use. Which applications suit this precision pin best? Typical uses include end‑measurement checks, reference gauges in inspection jigs and pin checks during assembly, where tight tolerance verification is required. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
8.17mm Gauge Pin, Workshop Version, ±0.001 mm Accuracy, 50mm Length - Metav IndustryLine
Take advantage of precise, repeatable checks with a compact, workshop‑grade gauge pin that combines ±0.001 mm tolerance and a robust special steel construction for dependable in‑process inspection. Order the gauge pin directly via Metav Werkzeuge or consult the Metav team for application guidance. Gauge pin, 8.17 mm ±0.001 mm — Workshop version (Metav IndustryLine) Gauge pin, 8.17 mm ±0.001 mm is a single‑piece inspection pin intended for dimensional end checks and fixture setting in workshop environments Workshop version for daily use Diameter 8.17 mm ±0.001 mm precision 50 mm overall length for stable handling Supplied in protective transport case Accurate tolerance for repeatable inspection The gauge pin is manufactured to a nominal diameter of 8.17 mm with an accuracy of ±0.001 mm, delivering high precision for go/no‑go checks, alignment and end‑measurement tasks. This level of tolerance reduces uncertainty in pass/fail decisions and minimises rework by ensuring that each verification is directly comparable to the nominal size. The compact geometry and fine finish support consistent contact conditions, which is essential when multiple operators perform short, repeat inspections during production runs. Robust build tailored to workshop conditions Produced from special steel, the pin offers a balance of hardness and toughness suitable for frequent handling in a workshop setting. With a length of 50 mm and a low mass (approx. 0.025 kg), the component is easy to position and manoeuvre while providing enough gripping length for stable use in jigs and fixtures. The workshop version designation indicates practical attention to everyday demands: corrosion‑resistant surface quality, repeatable seating in holders, and straightforward cleaning. The item is supplied in a transport case to protect the gauge during storage and transit. Streamlined inspection workflow and compatibility As a single‑gauge solution, the pin supports quick setup for dimensional verification and fixture setting, helping to shorten inspection cycles and improve throughput. The clearly defined nominal and tolerance values facilitate integration into inspection plans and documentation. Marked with its product code and identifiable by its characteristic finish, the component is suitable for use in conventional measurement benches and as an end reference in gauge stacks, contributing to repeatable results across shifts without complex calibration requirements specified in the baseline data. For reliable workshop gauging, request the Metav IndustryLine gauge pin (M323.817) from Metav Werkzeuge — contact via info@metav-werkzeuge.com or call +49 2822 7131930 for order details and application advice Technical data Article number: M323.817 GTIN: 4061905060571 Brand: Metav IndustryLine Material: Special steel Facts Nominal diameter: 8.17 mm Tolerance: ±0.001 mm Length: 50 mm Weight: 0.025 kg Special features Workshop version Supplied in transport case for transit protection Intended for end‑measurement and fixture setting Compact, single‑piece gauge pin design FAQ What are the nominal diameter and tolerance of the pin? The gauge pin M323.817 has a nominal diameter of 8.17 mm and a tolerance of ±0.001 mm. Which material is used for this gauge pin? This Metav IndustryLine gauge pin is made from special steel, chosen for wear resistance and stable contact behaviour. Is the pin suitable for end‑measurements and fixture setting? Yes. The M323.817 is designed for end measurements and as a reference element in fixture alignment and quick verification tasks. How is the product supplied for transit? The gauge pin M323.817 is supplied in a protective transport case to prevent damage during handling and transport. What routine maintenance is recommended? Regular cleaning, inspection for wear marks and light corrosion protection are recommended; store the pin in its transport case when not in use. Metav IndustryLine: Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
8.18mm Precision Gauge Pin ±0.001 mm Length 50 mm Workshop Version, Special Steel - Metav IndustryLine
Benefit from a compact, workshop-ready test pin that combines 1 µm tolerance, a precise 8.18 mm nominal diameter and a practical 50 mm reference length for reliable end‑dimension checks; order directly via Metav Werkzeuge or consult their specialists for application advice. Gauge pin M323.818 — precision 8.18 mm, ±0.001 mm, 50 mm length (Metav IndustryLine) Gauge pin M323.818 is a single precision pin for end‑dimension verification and reference measurements in workshop inspection and quality control. High-precision tolerance ±0.001 mm 8.18 mm nominal diameter Length 50 mm for reference checks Workshop version for robust handling Precision for reproducible end‑dimension checks The gauge pin is specified with a tolerance of ±0.001 mm (equivalent to 1 µm), which positions it within the high‑precision class for dimensional references. Such a fine tolerance means the pin delivers repeatable contact points for plug or reference measurements, reducing uncertainty when setting up fixtures or verifying small bores. By converting the tight dimensional specification into consistent inspection results, the pin supports production decisions that rely on exact end‑dimension conformity rather than subjective judgement. Built for workshop durability and consistent use Constructed from special steel, this single test pin is produced in a workshop version designed to withstand routine handling while preserving measurement integrity. The material choice and compact geometry ensure low susceptibility to bending and thermal drift during normal shop processes, so calibration intervals remain practical. Durability in combination with the fine tolerance translates into fewer replacements and stable reference behaviour across repeated measurement cycles. Simple handling and straightforward integration into inspection routines With a 50 mm length and a nominal 8.18 mm diameter, the pin serves as an uncomplicated reference tool for end‑dimension checks, fixture set‑up and quick pass/fail verifications. The single‑piece format allows direct use in comparison against master gauges or as a reference in pneumatic or manual checking fixtures. Its compact form factor and clear metrological specification facilitate easy documentation in inspection plans and seamless incorporation into existing quality workflows. Contact Metav Werkzeuge in Emmerich for tailored supply and technical advice on Metav IndustryLine gauge pins: info@metav-werkzeuge.com | +49 2822 7131930 Technical data Article number: M323.818 SKU: M323.818 GTIN: 4061905061066 Material: Special steel Weight: 0.025 kg Facts Diameter: 8.18 mm Tolerance: ±0.001 mm Length: 50 mm Special features Single test pin Workshop version Intended for end‑dimension checks FAQ What tolerance does the gauge pin offer? The gauge pin M323.818 is specified at ±0.001 mm (1 µm), providing a high level of dimensional precision for reference and inspection tasks. Is this pin supplied as a single item or part of a set? This entry describes a single test pin (M323.818) supplied individually for flexible use in inspection and fixture setups. What material is the pin made from and what does that mean for use? The pin is manufactured from special steel, chosen to balance hardness and resistance to wear for repeated workshop use while maintaining dimensional stability. For which applications is this gauge pin intended? The pin is intended for end‑dimension verification, reference measurements and integration into inspection procedures where a precise nominal diameter of 8.18 mm is required. Can the pin be used to set up inspection fixtures and master references? Yes, the compact 50 mm length and tight tolerance make the pin suitable as a reference element when configuring fixtures or checking bores against a known datum. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
8.19mm Gauge Pin ±0.001 mm Length 50 mm Workshop Finish - Metav IndustryLine
A workshop-grade gauge pin that combines ±0.001 mm accuracy with a compact 8.19 mm diameter and a 50 mm usable length for reproducible fit and end‑measure checks; supplied in a protective transport case for secure storage and handling. Order the M323.819 gauge pin directly via Metav Werkzeuge or ask our consultants if further technical data are required. M323.819 gauge pin (single) — 8.19 mm, ±0.001 mm tolerance The M323.819 gauge pin (single) is a workshop‑grade precision pin for end‑measure inspection and go/no‑go fit checks in metrology and quality control environments. Workshop-grade precision test pin Diameter 8.19 mm with ±0.001 mm tolerance 50 mm hardened special-steel length Supplied in protective transport case Measurable accuracy that reduces rework and rejects The core advantage of this gauge pin is its ±0.001 mm accuracy, which delivers a clear, measurable basis for pass/fail decisions during final inspection. With a defined 8.19 mm diameter and laboratory‑grade tolerance, the pin permits repeatable dimensional verification that reduces uncertainty in assembly and avoids costly rework. The numerical specification offers a straightforward comparison against drawing tolerances and machine capability figures, enabling rational decisions in incoming inspection and process control. Robust design built for frequent workshop use Designed as a workshop‑grade tool, the pin is manufactured from special steel, which provides the surface hardness and wear resistance required for repeated insertion and extraction in jigs and fixtures. The 50 mm length gives enough engagement for stable seating while remaining compact for handheld handling or fixture mounting. The modest mass and solid construction minimise deformation during use, so the component retains its geometric integrity across many inspection cycles — an important consideration for throughput in production environments. Integrates simply into existing inspection workflows As a single‑piece gauge, the pin is suitable for quick go/no‑go checks, alignment templates and end‑measure verification. The clear numeric specification and compact form factor mean it can be used alongside bench fixtures, plug gauges and optical comparators without special adaption. Traceable identification via the SKU and GTIN facilitates inventory control and replacement planning, while the transport packaging protects the surface finish during storage and transport. Practical handling, storage and documentation benefits Delivery includes a protective transport case, which supports safe storage and reduces the risk of accidental surface damage that would affect measurement accuracy. The pin’s compact geometry and clear tolerance marking simplify documentation in inspection reports and parts lists. Combined with Metav’s supply chain and product support, the gauge pin forms part of a practical toolkit for workshops and quality departments aiming for consistent final checks and reduced production variance. Choose the workshop‑grade precision of the Metav IndustryLine M323.819 gauge pin for reliable end‑measure verification — contact Metav Werkzeuge for supply and technical advice at info@metav-werkzeuge.com or +49 2822 7131930 Technical data Article number: M323.819 GTIN: 4061905061585 Label: Prüfstift, einzeln, 8,19mm, +/- 0.001 mm Länge 50 mm SKU: M323.819 Facts Diameter: 8.19 mm Tolerance: ±0.001 mm Length: 50 mm Weight: 0.025 kg Special features Material: special steel Workshop version Supplied in protective transport case Accuracy: ±0.001 mm Category: gauge pins FAQ What inspection tasks is this gauge pin suited for? The M323.819 gauge pin is intended for end‑measure checks, fit and clearance verification, and simple go/no‑go seating tests in workshop and quality‑control routines. Is the material resistant to regular use in a production environment? Yes, the pin is manufactured from special steel and the M323.819 is supplied in a protective transport case to preserve the surface and dimensional integrity during repeated handling. Can the pin be used in fixtures and jigs? The compact 8.19 mm diameter and 50 mm length make the M323.819 suitable for mounting in inspection fixtures, templates and alignment tools without custom modification. How does the ±0.001 mm tolerance affect process control? A tolerance of ±0.001 mm provides a high level of resolution for final assembly checks, enabling clearer decisions on part conformity and helping to reduce downstream rework. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
8.1mm Gauge Pin, Single, ±0.001mm, 50mm Length, Workshop Version - Metav IndustryLine
Benefit from the combination of ultra‑fine tolerance ±0.001 mm, a nominal diameter of 8.10 mm and a robust 50 mm length to secure repeatable end‑dimension checks; order the gauge pin directly via Metav Werkzeuge or consult our specialists for integration into inspection routines. Gauge pin M323.810 — single 8.10 mm, ±0.001 mm, 50 mm (Metav IndustryLine) Gauge pin M323.810 for dimensional verification in workshop and quality‑control environments, designed as a single precision inspection pin with a nominal diameter of 8.10 mm and a tolerance of ±0.001 mm Single precision gauge pin 8.10 mm ±0.001 50 mm length, workshop execution Supplied in transport case for protection Precision that reduces rework and inspection time The inspection pin delivers industrial‑grade dimensional certainty with a nominal diameter of 8.10 mm and a tolerance of ±0.001 mm, suitable for verifying bore sizes, end‑dimensions and assembly fits. Manufactured from special steel, the pin combines wear resistance with stable geometry so that routine checks remain consistent over time. The narrow tolerance cuts uncertainty in quality control, enabling faster decision making on pass/fail checks and reducing downstream rework. Durable design for demanding workshop use Engineered as a workshop execution component, the pin offers mechanical resilience for repeated handling on the shop floor. The 50 mm length provides a stable engagement depth for most common verification tasks while the compact mass (approx. 0.025 kg) minimises handling fatigue during batch checks. Supplied in a protective transport case, the item remains protected in storage and transit, preserving the surface finish and the specified tolerance for each inspection cycle. Practical integration and traceable identification The single gauge pin is a straightforward addition to inspection kits and can be paired with existing plug gauge sets or dimensional fixtures for quick verification workflows. Clear identification with SKU and GTIN supports inventory tracking and process documentation; the robust geometry means fewer replacements and a predictable service life, which in turn contributes to a lower total cost of inspection ownership for the workshop. For reliable shop‑floor measurements and simple integration into inspection routines, request the Metav IndustryLine gauge pin M323.810 from Metav Werkzeuge — our technical advisors are available to recommend the right configuration for existing gauges and fixtures Technical data Article number: M323.810 GTIN: 4061905060502 Manufacturer: Metav IndustryLine Facts Diameter: 8.10 mm Length: 50 mm Tolerance: ±0.001 mm Weight: 0.025 kg Special features Material: Special steel Workshop execution Supplied in transport case FAQ What is the intended use of this inspection pin? This gauge pin is intended for dimensional verification tasks such as bore checks and end‑dimension inspection; the M323.810 is suitable for routine workshop and quality‑control applications. Is the tolerance suitable for precision assembly checks? The specified tolerance of ±0.001 mm makes the inspection pin appropriate for high‑precision verification where micrometric conformity is required. How is the item delivered and protected during transport? The pin is supplied in a protective transport case to preserve the surface and maintain dimensional integrity during storage and shipping. Which material is used for the pin and why is it beneficial? The pin is made from special steel, chosen for its wear resistance and capacity to maintain stable geometry under repeated use. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
8.21mm Gauge Pin ±0.001mm Length 50mm Workshop Version - Metav IndustryLine
Take advantage of high repeatability and compact handling: the combination of 8.21 mm diameter, ±0.001 mm tolerance and a 50 mm length ensures reliable end-dimension verification with low measurement uncertainty; ideal for final checks in production and inspection. Order the gauge pin directly via Metav Werkzeuge or contact our consultants for application advice. Gauge pin M323.821 — precision gauge pin, 8.21 mm ±0.001 mm, 50 mm length (Metav IndustryLine) The Gauge pin M323.821 is a workshop-grade precision plug intended for final-dimension and end‑mass checks in metrology and production environments Diameter 8.21 mm, tolerance ±0.001 mm Length 50 mm for compact measurements Made from special steel, workshop grade Consistent precision for final inspections A tolerance of ±0.001 mm positions this gauge pin in the high‑precision segment used for critical end‑dimension checks. The tight tolerance reduces uncertainty in pass/fail decisions, which in turn lowers rework rates and increases throughput in inspection stations. By using a fixed-diameter reference of 8.21 mm, traceable checks on bores, seats and mating parts become repeatable and quick to execute, supporting lean quality processes and faster cycle times. Durable workshop design for dependable handling Constructed from special steel and specified as a workshop-grade item, the pin delivers wear resistance and stable geometry under routine use. The 50 mm length provides a compact grip area and sufficient engagement for short-seat or through-bore verification, while the low mass supports easy handling during repetitive tests. The robust finish minimises the need for frequent replacement, making the component a practical choice where reliability and uptime matter. Seamless fit into inspection workflows Equipped with a clear identification (SKU M323.821) and industry-standard data for procurement, the pin integrates into existing quality routines without extra adaptation. Its compact form factor simplifies storage and pick‑and‑place handling at measuring benches or inspection fixtures, and its repeatability supports statistical process control activities. Metav’s supply chain and quality filter in Emmerich ensure consistent availability and compatibility with workshop inventories, enabling organisations to democratise precision across multiple workstations. Contact Metav Werkzeuge for application-specific advice or to secure the Metav IndustryLine gauge pin M323.821 for immediate inclusion in inspection kits Technical details Article number: M323.821 GTIN: 4061905061608 SKU: M323.821 Manufacturer: Metav IndustryLine Measured values Nominal diameter: 8.21 mm Tolerance: ±0.001 mm Length: 50 mm Weight: 0.025 kg Features Material: Special steel Workshop version GTIN assigned FAQ What level of accuracy does this pin provide? The gauge pin delivers an accuracy of ±0.001 mm, suitable for high‑precision end‑dimension checks with visibly reduced measurement uncertainty. Can the pin be used for bore verification and plug‑gauge tasks? Yes. The 8.21 mm diameter and 50 mm length make the pin well suited for bore verification, seat checks and similar plug‑gauge applications. What is the material and how does it affect durability? Made from special steel, the pin offers enhanced wear resistance and dimensional stability under normal workshop use. How is the product identified for procurement? The item is listed as SKU M323.821 with GTIN 4061905061608 for straightforward ordering and inventory management. Is this gauge pin supplied with calibration? Calibration is not specified here; the product is supplied as a precision workshop component. For calibrated delivery options, please consult Metav Werkzeuge for available certificates and services. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
8.22mm Gauge Pin ±0.001mm Length 50mm Workshop Version - Metav IndustryLine
Take advantage of the combination of industrial accuracy, compact workshop design and proven material quality for repeatable end‑measurements; order the test pin directly via Metav Werkzeuge or consult our specialists for application support. M323.822 Test Pin (8.22 mm) — Metav IndustryLine, ±0.001 mm tolerance M323.822 is a precision test pin designed for end‑measurements and inspection tasks in workshop environments, offering high dimensional stability and a compact 50 mm length for tight fixtures. Diameter 8.22 mm with ±0.001 mm tolerance Workshop version with robust construction Manufactured from special steel for wear resistance Compact 50 mm length for confined assemblies Precision that prevents rework and speeds inspection The M323.822 gauge pin is built for repeatable metrology where tolerances decide accept or reject. With a declared accuracy of ±0.001 mm and a nominal diameter of 8.22 mm, the pin provides a measurable improvement in process certainty compared with coarse gauges. The tight tolerance reduces unnecessary rework by minimising measurement uncertainty; operators and quality teams benefit from quicker decisions at inspection stations and fewer downstream rejects. The combination of dimensional consistency and compact form makes this probe an efficient component for fixture checks and pass/fail evaluations. Workshop‑proven material and handling benefits Constructed from special steel in a workshop version, this single unit is intended to withstand daily handling and occasional knocks without rapid wear. The 50 mm length keeps the centre of mass low for stable insertion and retrieval in confined setups, while the solid material reduces the risk of deformation under typical contact forces. For maintenance and longevity, the material choice ensures consistent surface hardness and corrosion resistance within standard workshop environments, giving a reliable reference length for repetitive measurement tasks and inspection routines. Versatile use across inspection and assembly workflows As an individual test pin, this component integrates easily into inspection benches, go/no‑go fixtures and measuring jigs for end dimensions. The compact profile and precision diameter suit alignment, bores inspection and calibration of small assemblies where spatial constraints apply. Using this gauge pin can streamline quality control by standardising the measurement step in assembly sequences, cutting cycle time and supporting traceable measurement procedures in production. The product’s GTIN and SKU facilitate inventory management and reordering within existing procurement systems. Contact Metav Werkzeuge for specification matching and to arrange supply of the Metav IndustryLine M323.822 test pin for precision inspection tasks Technical data Article number: M323.822 GTIN: 4061905061615 SKU: M323.822 Label: Prüfstift, einzeln, 8,22mm, +/- 0.001 mm Länge 50 mm Facts Diameter: 8.22 mm Length: 50 mm Tolerance / Accuracy: ±0.001 mm Weight: 0.025 kg Special features Material: special steel Version: workshop execution Unit: single test pin Category: Test pins (Messstifte) FAQ What tolerance can be expected from this test pin? The M323.822 test pin is specified with an accuracy of ±0.001 mm, providing the fine resolution required for tight end‑measurements. Is the material suitable for regular workshop use? Yes, the pin is made from special steel and supplied in a workshop‑rated execution intended for frequent handling and inspection tasks. Can this pin be used for bore alignment and go/no‑go checks? The compact 50 mm length and precise 8.22 mm diameter make it suitable for bore alignment, go/no‑go checks and small‑assembly inspection fixtures. How is this item identified for procurement and stock control? This test pin is listed under SKU M323.822 and GTIN 4061905061615 for straightforward ordering and inventory management. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
8.23mm Test Pin, Single, ±0.001mm Accuracy, 50mm Length, Workshop Version - Metav IndustryLine
Take advantage of high-precision measuring capability and robust workshop construction to reduce scrap and speed up inspection tasks; the compact 8.23 mm diameter with ±0.001 mm tolerance and a 50 mm gauge length deliver consistent end-measurements — order the gauge pin directly via Metav Werkzeuge or contact our consultants for procurement advice Metav IndustryLine Gauge Pin M323.823 — 8.23 mm, ±0.001 mm, 50 mm length A Metav IndustryLine gauge pin designed for precise end-measurements and quick workshop verification of bores and fits Workshop-grade construction Diameter 8.23 mm, tolerance ±0.001 mm 50 mm length for end-measurements Special steel for daily use Accuracy that reduces rework and keeps production moving The gauge pin provides a ±0.001 mm tolerance, making it suitable for tasks where small deviations have immediate effects on assembly and function. With a compact 8.23 mm diameter and a 50 mm measuring length, the pin offers repeatable results when checking end dimensions or verifying bore fits. This level of precision minimises rework, shortens inspection cycles and supports a more efficient quality loop in the workshop. Technical terms such as tolerance and gauge length are used here to describe measurable properties that directly translate into fewer rejects and more predictable downstream processes. Robust design for everyday inspection tasks Manufactured from special steel, the component is finished for workshop use and engineered to withstand frequent handling. The simple, single-piece construction ensures low set-up time for handheld checks or fixture-based inspections. Its light mass (0.025 kg) and compact form make positioning straightforward while maintaining stiffness where it matters, so the measurement remains stable even during repetitive checking. For inspection teams that perform fast pass/fail checks, this reliability in construction translates into consistent decision-making at the bench or on the shop floor. Traceable sourcing and seamless procurement Identified as SKU M323.823, the gauge pin is listed under metrological consumables and is compatible with standard plug gauges and comparison routines. A clear GTIN entry supports inventory management and reordering. Sourcing via an established partner provides certainty about material origin and batch consistency, which helps purchasing and quality departments maintain traceability and documentation. Metav’s position as a precision partner brings workshop-level access to calibrated and reliable measuring tools, supporting uninterrupted production and dependable inspection results. Contact Metav Werkzeuge for procurement advice or to discuss suitability for specific inspection procedures — call +49 2822 7131930 or email info@metav-werkzeuge.com for fast, expert support from Emmerich Technical data SKU: M323.823 GTIN: 4061905061622 Manufacturer: Metav IndustryLine Facts Diameter: 8.23 mm Accuracy: ±0.001 mm Length: 50 mm Weight: 0.025 kg Special features Material: special steel Application: end measurements Designation: single gauge pin Category: Messstifte FAQ What tolerance can be expected from this gauge pin? The gauge pin is specified at ±0.001 mm, which ensures tight repeatability for end-measurements and precision checks. Is this pin suitable for everyday workshop use? Yes, the workshop-grade construction and special steel make the pin suitable for frequent inspection tasks in production and assembly environments. How is the product identified for reordering? The item is listed as SKU M323.823 and the GTIN 4061905061622 assists in catalogue and inventory systems for straightforward reordering. Can this gauge pin be used to check bore fits and end-wall dimensions? The 8.23 mm diameter and 50 mm length are optimised for end-measurements and verification of bore fits where a precise reference mandrel is required. Who supplies this gauge pin and where is support available? Metav IndustryLine supplies the gauge pin; procurement and technical enquiries are handled by Metav Werkzeuge in Emmerich for European customers. Metav IndustryLine: Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
8.24mm Test Pin Single ±0.001mm Length 50mm Workshop Version - Metav IndustryLine
Take advantage of the combination of micron‑level accuracy and robust workshop construction to secure reliable reference checks and reduce rework in inspection routines; delivered in a protective case for safe transport. Order the M323.824 gauge pin directly via Metav Werkzeuge or ask our consultants if needed. M323.824 Gauge pin — 8.24 mm, ±0.001 mm accuracy, 50 mm length (Metav IndustryLine) The M323.824 gauge pin is a single precision pin designed for end‑measurements, reference checks and bore verification in workshop inspection environments. Workshop version for robust use Diameter precision 8.24 mm, ±0.001 mm Length 50 mm for deep reference measurements Delivered in protective transport case Micron‑level reference for consistent quality control The M323.824 is manufactured with an accuracy of ±0.001 mm, equivalent to one micrometre, which positions it as a high‑precision reference for dimensional checks. A diameter of 8.24 mm combined with a 50 mm overall length provides a stable contact area for bore and hole verification, enabling reproducible results when setting fixtures or verifying finished components. The fine tolerance reduces uncertainty in pass/fail assessments and supports tighter process control in serial production. Designed to withstand workshop conditions while preserving precision Built as a workshop version, the pin combines a compact design with durable special steel construction to resist wear during everyday use. The material choice balances surface hardness and dimensional stability so that the accuracy is preserved over multiple handling cycles. Delivered in a protective transport case, the item arrives ready for storage and safe transport between job stations, reducing the risk of damage that can impair repeatability. Practical integration into inspection and setup workflows As a single gauge pin, this measuring element is ideal for use as a setting or reference tool during machine set‑up, tool alignment and quick in‑process checks. Its compact form factor and mass (approx. 0.025 kg) make handling straightforward while enabling precise seating in bores and seats. Incorporating this precision pin into routine checks shortens decision times and supports clearer go/no‑go assessments, which in turn helps to lower scrap rates and rework costs. Contact Metav Werkzeuge for specific application advice and secure the M323.824 gauge pin for dependable micron‑level verification directly from our Emmerich distribution centre. Technical Data Article number: M323.824 GTIN: 4061905061639 Brand: Metav IndustryLine Facts Diameter: 8.24 mm Length: 50 mm Tolerance: ±0.001 mm Weight: 0.025 kg Special features Material: Special steel Workshop version Delivered in protective transport case Category: Gauge pins (Messstifte) FAQ What level of accuracy does this gauge pin provide? The M323.824 gauge pin from Metav IndustryLine offers an accuracy of ±0.001 mm, suitable for high‑precision reference and verification tasks. Can the pin be used for bore and hole verification? Yes, the 8.24 mm diameter and 50 mm length make the pin suitable for bore, seat and end‑face checks in workshop inspection routines. What material is the measuring pin made of? The pin is made from special steel, chosen to combine dimensional stability with wear resistance for repeated use. Is the gauge pin supplied ready for storage and transport? The M323.824 is delivered in a protective transport case, which helps to protect the precision surface during handling and transport. Which applications are typical for this single gauge pin? Typical uses include fixture set‑up, quick in‑process checks, alignment tasks and any inspection requiring a precise reference pin. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
8.25mm Gauge Pin ±0.001 mm Length 50 mm Workshop Finish - Metav IndustryLine
Take advantage of the combination of ±0.001 mm accuracy, a compact 8.25 mm diameter and a workshop‑grade design for dependable end‑dimension verification; order the gauge pin via Metav Werkzeuge or contact their consultants for specification support. Gauge pin M323.825 by Metav IndustryLine — 8.25 mm, ±0.001 mm Gauge pin M323.825 is a single test pin designed for precise end‑dimension checks and compact measuring tasks in workshop environments Workshop version for robust use Diameter 8.25 mm with ±0.001 mm accuracy Length 50 mm for compact measuring tasks Supplied in protective case for transport Reliable sub‑millimetre precision for end‑dimension checks The M323.825 gauge pin delivers a rated tolerance of ±0.001 mm, making it suitable where repeatable, sub‑micrometre accuracy is required for final dimensional verification. The tight tolerance reduces uncertainty in go/no‑go checks and comparative measurements; when used in plug gauges or fixture checks the 8.25 mm diameter provides a stable reference that minimises eccentricity effects. The combination of a small form factor and high precision supports efficient inline inspections, shortening decision loops and improving first‑pass yield. Robust workshop design that withstands daily handling Designed as a workshop version, the pin is manufactured from special steel, a choice that balances wear resistance with dimensional stability under frequent use. With a nominal length of 50 mm and a mass of 0.025 kg, the part is easy to handle and integrates well into jigs, modular fixtures or manual inspection benches. The compact geometry reduces bending moment during measurement, which helps maintain the declared tolerance in repetitive checks and supports consistent results across production shifts. Compact handling and safe transport for small‑part inspection Classified for micro applications as an extremely compact gauge, the pin is ideal for end‑dimension verification of small bores, dowels and turned components where space is limited. Delivery in a protective case safeguards the measuring surface during transport and storage, preserving accuracy and reducing rework from contamination or accidental damage. The item supports fast inspection routines and is suitable for adoption in both maintenance benches and small series production lines, contributing to steady process control and fewer stoppages. For integration advice or to specify the Metav IndustryLine gauge pin M323.825 for your inspection process, contact Metav Werkzeuge to ensure the correct fixture and handling procedures are applied. Technical Data SKU: M323.825 GTIN: 4061905061646 Description: Test pin, single, 8.25 mm, ±0.001 mm, length 50 mm Weight: 0.025 kg Dimensions & accuracy Diameter: 8.25 mm Length: 50 mm Tolerance: ±0.001 mm Special features Material: Special steel Workshop version Supplied in protective case for transport FAQ What tolerance does the gauge pin offer? The gauge pin M323.825 is specified with a tolerance of ±0.001 mm for high‑precision end‑dimension checks. What material is used for the pin? The test pin is made from special steel, chosen for wear resistance and dimensional stability in workshop conditions. For which applications is this pin suitable? This compact, micro‑class pin is intended for end‑dimension verification of small bores, dowels and turned parts in production and quality inspection. Is the pin supplied ready for transport and storage? Yes. The M323.825 is supplied in a protective case to reduce the risk of damage during transport and storage. What are the exact dimensions and the SKU for ordering? Diameter 8.25 mm, length 50 mm, weight 0.025 kg; SKU M323.825 is used for ordering and identification. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
8.26mm Gauge Pin ±0.001mm Length 50mm, Workshop Version, Special Steel, Supplied in Case - Metav IndustryLine
Take advantage of the combination of ultra‑fine accuracy, workshop‑proven materials and compact handling for reliable end‑dimension checks and fewer rework cycles. Order the gauge pin directly via Metav Werkzeuge or ask the consultants for application advice. Gauge pin M323.826 — 8.26 mm diameter, ±0.001 mm accuracy (Metav IndustryLine) A gauge pin M323.826 designed for precise end‑dimension verification in workshop and inspection workflows High‑precision ±0.001 mm tolerance Diameter 8.26 mm ground to fit 50 mm working length for fixture checks Workshop‑grade special steel with transport case Precision where one micrometre matters This inspection pin delivers an accuracy of ±0.001 mm, equivalent to one micrometre, which places it in the realm of fine metrological control rather than routine gauging. Such tolerance is suitable for end‑dimension verification where component fits and clearances determine assembly quality. The 8.26 mm diameter is ground and honed for concentricity, helping to reduce measurement scatter and minimise downstream rework. The result is faster process validation and fewer rejected parts during quality control. Robust workshop design for repeatable checks Manufactured in a workshop version and made from special steel, the pin balances wear resistance with machinability for regular use at the bench. Its 50 mm length provides sufficient reach for many fixture and bore checks while remaining compact for handheld inspection. At 0.025 kg the instrument is light enough for single‑operator handling yet stiff enough to avoid flicker during fits. Supplied in a protective transport case, the pin is protected in transit and storage, ensuring the measurement surface remains pristine. Practical handling and application notes The instrument functions as a precision reference for end‑measure checks, press‑fits and gauging inserts in jigs and fixtures. Gentle handling and clean measurement surfaces maintain the specified tolerance; avoid knocks and contamination to preserve the ground finish. The compact format makes the pin suitable for integration into inspection routines and as a reference master when setting up plug gauges or comparative checks. Its geometry supports consistent seating in bore centres for comparable results across repeated measurements. Identification, traceability and workshop benefits The product is identified by the GTIN and SKU to support inventory and traceability in procurement systems, and the compact design reduces storage space while increasing practical availability at the bench. As part of Metav IndustryLine, this pin complements a wider assortment of inspection aids that simplify procurement and consolidate quality standards. Choosing workshop‑grade components from a focused supplier reduces supplier complexity and supports predictable delivery into production. For reliable end‑dimension verification with Metav IndustryLine quality, contact Metav Werkzeuge in Emmerich for a product recommendation or technical clarification at info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: M323.826 GTIN: 4061905061653 Brand: Metav IndustryLine Core dimensions Diameter: 8.26 mm Length: 50 mm Tolerance: ±0.001 mm Weight: 0.025 kg Materials & features Material: Special steel Workshop execution Supplied in a transport case Intended use: End‑dimension checks FAQ What tolerance class does the gauge pin meet? The gauge pin is specified with a tolerance of ±0.001 mm, providing micrometre‑level control for end‑dimension verification. Is the pin suitable for repeated use in a workshop environment? Yes, the M323.826 is a workshop‑grade pin made from special steel and supplied in a transport case to protect the measurement surface during regular handling. What dimensions are available for this reference pin? This item is produced with an 8.26 mm diameter and a 50 mm length, as stated in the product identification. How should the measuring surface be maintained? Keep the pin clean and free of lubricants or grit; avoid impact and store it in the supplied transport case to preserve the ground finish and specified tolerance. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
8.27mm Gauge Pin, Single, ±0.001mm Accuracy, 50mm Length, Workshop Finish - Metav IndustryLine
Combine workshop-grade robustness, sub‑micron tolerance and a compact 50 mm length for reproducible end‑measurement work. Order the gauge pin directly via Metav Werkzeuge or consult the Metav specialists for application advice and delivery options. Gauge pin, single 8.27 mm (M323.827) — workshop test pin with ±0.001 mm accuracy, 50 mm length Gauge pin, single 8.27 mm (M323.827) is a compact inspection pin intended for precise end‑measurements and dimensional checks in workshop environments Workshop execution, robust design Tolerance ±0.001 mm Diameter 8.27 mm precision Length 50 mm for short‑reach checks Precision that supports faster inspection decisions The M323.827 gauge pin delivers a ±0.001 mm specification that translates into reliable repeatability for pass/fail checks and reference measurements. A tight nominal diameter of 8.27 mm reduces uncertainty in fit and clearance verification, so inspection cycles become more deterministic. The short 50 mm length keeps the pin rigid under manual handling, which minimises bending error and supports consistent contact during measurement. In practical terms, the combination of small form factor and fine tolerance reduces rework and speeds up throughput in small‑batch production or incoming inspection. Designed for workshop use and robust handling Constructed in special steel and labelled as a workshop execution, this single test pin tolerates the mechanical demands of everyday shop floor inspection. The compact geometry is suited to quick reference checks in fixtures, gauges and assembly trials, offering a balance between stiffness and manoeuvrability. Where tight fits must be checked repeatedly, the robust material and controlled manufacturing tolerances reduce surface wear and sustain dimensional integrity over many cycles, supporting long service life and predictable measurement outcomes. Practical integration into quality routines As a dedicated inspection element, the single gauge pin serves as a fixed reference for end‑measurement tasks and comparative checks within quality control processes. The straightforward geometry allows easy insertion into bores or mating features and quick recording of deviations against nominal values. For purchasing and logistics, Metav IndustryLine supplies this item with clear identification (M323.827) from the Emmerich distribution centre, which supports steady replenishment for production and test environments. The provenance and controlled supply chain contribute to traceable inventory management and predictable lead times. For workshop‑grade end‑measurement with Metav IndustryLine’s M323.827 gauge pin, contact Metav Werkzeuge in Emmerich for tailored advice and a delivery proposal Technical data Article number: M323.827 GTIN: 4061905061660 Brand: Metav IndustryLine Label: Gauge pin, single, 8.27 mm, ±0.001 mm, length 50 mm Facts Diameter: 8.27 mm Length: 50 mm Tolerance: ±0.001 mm Weight: 0.025 kg Special features Material: Special steel Version: Workshop execution Single gauge pin for end measurements Application: dimensional inspection and reference measurements FAQ What is the dimensional tolerance of this gauge pin? The M323.827 gauge pin (Metav IndustryLine) is specified with a tolerance of ±0.001 mm, suitable for high‑precision end‑measurement tasks. Which nominal diameter does the pin have? The inspection pin has a nominal diameter of 8.27 mm and is manufactured to tight tolerance for repeatable fit checks. Is the pin suitable for routine workshop inspection? Designed as a workshop execution item, the gauge pin is intended for regular use in shop floor and inspection settings where compact, rigid reference elements are required. What applications are typical for this single gauge pin? Common uses include end‑measurement of bores and shafts, reference checks in fixtures and quick go/no‑go verification in assembly and incoming inspection. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
8.28mm Test Pin ±0.001mm, 50mm Length, Workshop Version - Metav IndustryLine
Confident measurements are delivered by combining ±0.001 mm tolerance with a robust 8.28 mm diameter and a practical 50 mm working length, supporting reliable end‑measure and fit checks in production. Order the M323.828 gauge pin directly via Metav Werkzeuge or consult the specialists if application advice is required. M323.828 gauge pin — 8.28 mm, ±0.001 mm accuracy (Metav IndustryLine) The M323.828 gauge pin is a single precision plug designed for end‑measurement, fit checking and fine‑mechanical inspection tasks in workshop environments. Precision tolerance ±0.001 mm 8.28 mm hardened gauge diameter 50 mm working length Workshop‑grade special steel Secure tolerances for critical assemblies High repeatability is achieved through the ±0.001 mm tolerance, which minimises measurement uncertainty and reduces the risk of assembly rework. This degree of precision is suited to quality control steps where small deviations can cascade into costly downstream errors; the narrow tolerance makes the gauge pin a reliable reference for pass/fail checks and for setting up jigs or fixtures. By using a hardened, stable measuring element the process time for verification is shortened, supporting faster production cycles with consistent results. Compact format that enhances handling in fine work With an 8.28 mm diameter and a 50 mm working length the component sits in the micro measurement category (max 10–100 mm), offering an excellent stiffness‑to‑size ratio for fine‑mechanical and watchmaking tasks. The compact profile keeps the measuring element rigid under light loading and simplifies positioning in confined bores or small assemblies. Low mass and a concise working length also ease manual handling and integration into dedicated inspection aids, improving ergonomics during repetitive checks. Robust construction for everyday workshop use Made from special steel and released as a workshop version, the gauge pin is engineered to withstand routine handling and light contact with mating parts while maintaining dimensional integrity. The material choice provides resistance against wear in daily inspection tasks and ensures a stable reference surface for go/no‑go assessments. Supplied as a single test pin, the component is ideal for replacement when sets are customised or when a dedicated pin is required for a specific bore size. For specialist advice on integrating the Metav IndustryLine M323.828 gauge pin into quality control routines, contact Metav Werkzeuge at info@metav-werkzeuge.com or call +49 2822 7131930 Technical data SKU: M323.828 GTIN: 4061905061677 Diameter: 8.28 mm Tolerance: ±0.001 mm Length: 50 mm Material: Special steel Weight: 0.025 kg ECLASS: 21170231 Facts Diameter (numeric): 8.28 mm Length (numeric): 50 mm Tolerance (numeric): ±0.001 mm Weight (numeric): 0.025 kg Special features Single test pin supplied individually Workshop version for routine inspection Intended for end measurements and fit checks Category: gauge pins (messstifte) FAQ What accuracy does this gauge pin provide? The M323.828 gauge pin from Metav IndustryLine offers a tolerance of ±0.001 mm, suitable for high‑precision end‑measure and fit verification tasks. Which measurement tasks is this pin intended for? Designed for end measurements, fit checks and alignment tasks on small bores and precision components, the pin supports fine‑mechanical inspection and setting operations. What material is used and how durable is the pin? Manufactured from special steel, the workshop version combines surface hardness with resistance to routine handling, delivering stable reference surfaces during frequent checks. How does the 8.28 mm size influence application? At 8.28 mm the pin falls into the micro range (10–100 mm category), offering excellent rigidity and minimal flex for repeatable measurements in compact components. Is this a single item or part of a set? The product is supplied as a single test pin (SKU M323.828), allowing individual use in jigs or as replacement elements within custom inspection setups. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
8.29mm Gauge Pin ±0.001mm Length 50mm Workshop Version - Metav IndustryLine
Take advantage of the combination of workshop-ready robustness, micrometre-level accuracy and compact handling for reliable end‑measure checks. The M323.829 gauge pin delivers Ø 8.29 mm with a tolerance of ±0.001 mm and a 50 mm shaft, supplied in a protective transport case; order directly via Metav Werkzeuge or consult our specialists for application advice. Gauge pin M323.829 — Single precision verification pin, Ø 8.29 mm, ±0.001 mm (Metav IndustryLine) The gauge pin M323.829 is a single high‑precision verification pin intended for end‑measure checks and fixture verification in workshop and production environments. Single precision pin Ø 8.29 mm ±0.001 mm 50 mm length in special steel Workshop version for robust daily use Supplied in protective transport case Reduce downtime with reproducible precision The extremely tight tolerance of ±0.001 mm places this verification pin in a class where repeatability matters. Used as an end‑measure standard, the pin provides a clear reference for bore checks, alignment operations and assembly gauges, which reduces rework and speeds up inspection cycles. Because the diameter is specified as Ø 8.29 mm, interchangeability between fixtures and measurement stands is immediate; the consistent geometry eliminates guesswork during set‑up and shortens machine downtime. The emphasis here is on measurable benefits: fewer scrap parts, faster quality decisions and smoother production flow. Built for workshop use and safe transport Constructed from special steel and finished as a workshop version, the pin is optimised for daily handling and mechanical resilience. The 50 mm shaft length offers enough engagement for most verification tasks while remaining easy to position by hand or in fixture blocks. Delivery in a protective transport case preserves the calibrated surface during storage and transfer, keeping the reference geometry intact. This practical packaging supports on‑shop logistics: inspection tools stay protected between jobs and are ready for immediate use when required. Traceability and integration into quality routines As a single verification element, the pin is suitable for integration into modular inspection routines and assembly jigs. The solid specification and single‑piece supply make it straightforward to document traceability within a quality system, supporting serial checks and process validation. The compact form factor allows straightforward incorporation into existing gauge plates or bespoke test fixtures, while the clear technical specification simplifies procurement and inventory control. The robust construction and precise finish also mean reliable performance over repeated cycles, contributing to long‑term measurement stability. Contact Metav Werkzeuge today to request application guidance or to order the M323.829 workshop gauge pin with protective case directly from our Emmerich warehouse; email info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: M323.829 GTIN: 4061905062414 Manufacturer: Metav IndustryLine Material: Special steel Finish: Workshop version Supplied in: Protective transport case Facts Diameter: 8.29 mm Length: 50 mm Tolerance: ±0.001 mm Weight: 0.025 kg Special features Single verification/gauge pin Application: End‑measure checks, fixture verification Category: Gauge pins Packaging purpose: Transport protection FAQ What level of accuracy does this gauge pin provide? The M323.829 gauge pin is specified to ±0.001 mm, offering micrometre‑level accuracy suitable for verification and end‑measure tasks. Which materials is the pin made from and how does that help? This verification pin is produced from special steel, selected for dimensional stability and wear resistance to ensure long service life under workshop conditions. Is the pin supplied ready for use and how is it protected? The pin is supplied as a single item in a protective transport case to safeguard the calibrated surface during storage and transfer. Can the pin be used in fixture and jig assemblies? Yes — the 50 mm shaft and precise Ø 8.29 mm geometry make it suitable for integration into gauge plates, jigs and assembly fixtures for routine checks. Does the product support traceability in quality systems? The defined specification and single‑item supply of the M323.829 simplify documentation and traceability for quality control and process validation. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
Fast, tactile checks where electronics are impractical
Gauges and test pins provide unequivocal go/no-go results for threads, bores, gaps and radii without relying on electronics. The range covers plug gauges and ring gauges for internal and external threads, feeler gauges and precision feeler strips for micro‑gap assessment, plus probe pins and measuring pins for tactile diameter and pitch checks.
How these tools work in the production environment
Mechanical gauges operate as direct reference standards: a plug gauge or ring gauge verifies conformity to thread profiles and mating ability, while limit gauges separate accept from reject in a single step. Test pins are used to tactilely measure small bore diameters, centre‑to‑centre distances and radii. Manufactured from hardened gauge steel or ceramic and often precision lapped, these instruments deliver immediate physical results that are ideal for incoming inspection, machine‑side checks and final control.
Measurable benefits that affect production performance
- Reduced scrap and rework through rapid, unambiguous pass/fail assessment.
- Increased repeatability thanks to very low measurement uncertainty and fine lapping.
- Lower downtime: quick checks at the machine save cycle time and reduce setup periods.
- Durable construction with high wear resistance from specialised, low‑distortion alloys.
- Versatile delivery formats: individual gauges, organised sets in wooden cases or metre‑length feeler rolls compliant with DIN 2269.
Why Metav is the practical choice for precision supplies
Metav combines decades of expertise with a broad warehouse and quality filtering from Emmerich. As a precision partner for industry, craft and trade, Metav supplies a comprehensive selection of gauges and test pins alongside complementary tools such as precision calipers and setting rings. With over 48,000 customers and a catalogue exceeding 250,000 items, Metav is positioned to supply reliably, reduce vendor complexity and support traceable quality control to national standards.
Summary
Gauges and test pins are indispensable for dependable, repeatable quality assurance where tactile, mechanical verification is preferred. Choose these plug gauges, ring gauges, feeler strips and probe pins when immediate, robust measurement decisions are required on the shop floor.
FAQ
What materials are gauges and test pins typically made from?
Gauges and test pins are usually manufactured from hardened gauge steel for durability and wear resistance; ceramic variants are available where thermal stability and minimal wear are critical.
How do thread gauges ensure mating capability?
Thread plug gauges and ring gauges check flank diameters and thread form against standards, providing a clear go/no‑go verdict that confirms pairability with mating parts.
Which tolerance class should I choose for probe pins and gauge sets?
Select tolerance classes aligned with your inspection requirements; for high‑precision tasks, sets produced to DIN 2269 or equivalent tolerance classes ensure micrometre‑level control and repeatability.
Can feeler gauges measure contact gaps in valve and engine work reliably?
Yes. Feeler gauges and precision feeler strips, supplied either as a fan or metre‑length rolls, allow accurate assessment of valve clearances and contact gaps down to micrometre increments.
How do limit gauges speed up in‑process inspection?
Limit gauges separate good from bad in a single, tactile operation, enabling rapid go/no‑go checks at the machine and reducing both inspection time and the likelihood of human interpretation errors.
Fragen zu diesen Produkten??
Mit mehr als 30 Jahren Erfahrung beraten wir Sie gerne persönlich.
Tel.: +49 2822 7131930
Mail: info@metav-werkzeuge.com