DCMT 11T304 AH725 Wendeplatten - Tungaloy
Take advantage of the combination of an AH725 PVD-coated carbide grade, precise 0.4 mm corner radius and ISO compatibility for reliable turning performance and consistent surface quality; order the insert directly via Metav Werkzeuge or request further advice from the consultants. DCMT11T304 AH725 indexable turning insert — ISO-standard, PVD-coated carbide by Tungaloy DCMT11T304 AH725 is an ISO-standard indexable insert designed for external and internal turning, offering universal performance across mixed materials and high process security PVD-coated AH725 universal grade ISO DCMT11T304 rhombic 55° geometry 0.4 mm corner radius for fine finishes Cylindrical hole with 40°–60° countersink Consistent results across Stahl and rostfreier Stahl for mixed-production runs The PVD-coated carbide grade AH725 delivers a balance of wear resistance and edge toughness that suits batch production with varying materials. Its formulation supports stable chip formation and reduces the risk of edge chipping when machining both Stahl and rostfreier Stahl, making the insert appropriate for shops that face frequent material changes. The single sided chipbreaker contributes to controlled chip flow, which in turn lowers interruption risk and helps maintain cycle times—valuable where process security and repeatability are priorities. Precision fit and ISO compatibility to shorten setup times Built to the ISO-standard form DCMT11T304, the rhombic 55° geometry ensures a predictable contact angle for turning operations, while the cylindrical hole with one-sided countersink (40°–60°) enables secure clamping in standard holders. Compatibility is determined by form, clearance angle, tolerance class, fastening method, size and thickness, which simplifies tool selection for compatible holders and reduces adapter requirements. The result is faster changeovers and fewer alignment adjustments during tool replacement. Stable cutting performance and economical tool life The combination of the AH725 coating and carbide substrate provides robust wear characteristics for small to medium-sized tools and demanding finishing tasks. The 0.4 mm corner radius supports fine surface finishes without sacrificing edge strength, and the plate thickness of 3.97 mm contributes to rigidity in the clamped system. Overall, this design promotes consistent tool life and lowers the frequency of insert changes, improving uptime and delivering a favourable cost-in-use for production environments that prioritise both quality and efficiency. For dependable, universal turning performance choose the Tungaloy DCMT11T304 AH725 insert — contact Metav Werkzeuge for product availability and technical consultation at info@metav-werkzeuge.com or +49 2822 7131930 Technical data Article number: 6856780 SKU: 6856780-Tungaloy Manufacturer SKU: TUN6856780 Manufacturer article number: 6856780 Manufacturer: Tungaloy Core specifications Geometry angle: 55° Size: 11 Thickness: 3.97 mm Corner radius: 0.4 mm Clearance (relief) angle: 7° Special features Carbide, PVD coating (AH725) One-sided chipbreaker Rhombic indexable insert, 55° Cylindrical hole + one-sided countersink (40°–60°) ISO turning insert series Suitable for Stahl and rostfreier Stahl FAQ Is this insert suitable for machining rostfreier Stahl? Yes. The DCMT11T304 AH725 insert from Tungaloy is designed as a universal, breakage-resistant grade suitable for machining both Stahl and rostfreier Stahl, offering stable cutting and controlled chip formation. Which holder types are compatible with this insert? Compatibility depends on holder form, relief angle, tolerance class, fastening method, size and thickness; the ISO DCMT11T304 form is compatible with standard rhombic 55° external and internal turning holders designed for that insert geometry. What surface finish can be expected with the 0.4 mm corner radius? A 0.4 mm corner radius supports fine finishing operations while maintaining edge strength; paired with the AH725 PVD coating, it helps achieve consistent surface quality and repeatable part tolerances. What is the hole and fastening style of the insert? The insert features a cylindrical hole with a one-sided countersink between 40° and 60°, enabling secure clamping in compatible ISO holders. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
DCMT 11T304 AH725 Wendeplatten - Tungaloy
DCMT11T304 AH725 Tungaloy-Wendeplatte Wendeplatte zum Drehen Die DCMT11T304 AH725 ist eine ISO-genormte Wendeplatte zum Außen- und Innendrehen, ausgelegt für universellen Einsatz bei Stahl und rostfreien Stählen. Universelle Sorte AH725 für wechselnde Werkstoffe PVD-beschichtetes Hartmetall für hohe Prozesssicherheit Rhombische Form mit 55° Winkel für stabile Schnitte Zylindrisches Loch mit Senkung für sichere Befestigung Eckenradius 0,4 mm für feine Maßhaltigkeit Hohe Prozesssicherheit und Wirtschaftlichkeit bei Standardanwendungen Die Wendeplatte vereint Hartmetall-Werkstoff und PVD-Beschichtung, wodurch die Schneidkante verschleißfest bleibt und Standzeiten zuverlässig ausfallen. Für Betriebe, die häufig zwischen normalen Stahl- und rostfreien Stählen wechseln, bietet die Sorte AH725 eine ausgewogene Kombination aus Ausbruchfestigkeit und Vielseitigkeit. Daraus resultiert eine Reduktion von Rüstzeiten und weniger Werkzeugwechsel, was die Wirtschaftlichkeit in der Fertigung erhöht. Passgenaue Geometrie für stabile Spanbildung Die rhombische Plattenform mit einem Plattenwinkel von 55° und einem Freiwinkel von 7° sorgt für konstant gesteuerte Spanbildung. Der eingearbeitete Spanbrecher einseitig ist speziell ausgelegt, um die Späne sauber abzuleiten und die Schnittbedingungen bei wechselnden Bearbeitungsparametern stabil zu halten. Anwender profitieren dadurch von gleichbleibender Oberflächengüte und weniger Nacharbeit. Befestigung und Maße für unkomplizierte Integration Mit einem zylindrischen Loch samt einseitiger Senkung (40°–60°), einer Plattendicke von 3,97 mm und einer Plattengröße von 11 mm lässt sich die Platte schnell und zuverlässig in gängige ISO-Außenhalter einsetzen. Der Eckenradius 0,4 mm ermöglicht präzise Konturen und feine Maßtoleranzen, was besonders bei kleineren Werkzeugen und anspruchsvollen Konturen relevant ist. Zielgruppe und Anwendungsumfeld Diese Wendeplatte richtet sich an Dreherei- und Serienfertigungsbetriebe, die robuste, prozesssichere Lösungen für das Drehen von Stahl und rostfreien Stählen suchen. Besonders geeignet ist die Platte für Anwender, die Wirtschaftlichkeit und konstante Ergebnisse bei wechselnden Werkstoffen benötigen, ohne auf einfache Handhabung verzichten zu müssen. Empfehlung: Entscheiden Sie sich für die bewährte AH725-Sorte von Tungaloy für zuverlässige Standzeit und hohe Prozesssicherheit; bei Fragen zu Einbaumaßen oder Anwendungsparametern kontaktieren Sie bitte unseren technischen Vertrieb unter info@metav-werkzeuge.com oder telefonisch unter +49 2822 7131930 Produktmerkmale Artikelnummer: 6864870 Marke: Tungaloy Serie: ISO-Drehwendeschneidplatten Hersteller SKU: TUN6864870 Fakten Eckenradius: 0,4 mm Plattendicke: 3,97 mm Plattengröße: 11 mm Winkel: 55° Freiwinkel: 7° Besonderheiten Material: Hartmetall Beschichtung: PVD-beschichtet (PVD: physikalische Dampfabscheidung) Platte: rhombisch Loch: mit Loch Lochstil: zylindrisches Loch + einseitige Senkung (40°–60°) Spanbrecher: einseitig Einsatz: Drehen Sorte: AH725 (universelle ausbruchfeste Sorte für Stahl und rostfreie Stähle) FAQ Für welche Werkstoffe ist die Wendeplatte geeignet? Die DCMT11T304 AH725 von Tungaloy eignet sich primär für Stahl und rostfreie Stähle; die Sorte AH725 ist universell ausgelegt und bietet Ausbruchfestigkeit bei wechselnden Werkstoffen. Welche Vorteile bringt die PVD-Beschichtung? Die PVD-beschichtung der Tungaloy-Wendeplatte erhöht die Verschleißfestigkeit der Schneidkante und verbessert die Standzeit sowie die Prozesssicherheit bei höheren Schnittbedingungen. Wie beeinflusst der Eckenradius die Bearbeitung? Ein Eckenradius von 0,4 mm ermöglicht feine Konturen und bessere Maßhaltigkeit; er reduziert außerdem Kerbwirkung und verbessert die Oberflächengüte bei geringeren Vorschüben. Ist die Platte mit Standard-ISO-Haltern kompatibel? Ja, die DCMT11T304 ist ISO-genormt; Kompatibilität wird über Form, Freiwinkel, Toleranzklasse, Befestigung, Größe und Dicke sichergestellt. Die Angabe des Lochstils erleichtert die Auswahl des passenden Halters. Wann ist die einseitige Spanbrecher-Geometrie sinnvoll? Die einseitige Spanbrecher-Geometrie ist besonders nützlich, wenn eine gerichtete Spanableitung und stabile Spanform gewünscht sind, etwa bei variierenden Schnittparametern oder dünnwandigen Werkstücken. Hersteller: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Geschützte Markenzeichen und Warenbezeichnungen liegen im Recht ihrer jeweiligen Eigentümer. Markennamen und geschützte Warenbezeichnungen werden ausschließlich zu Erklärungszwecken genannt. Es besteht keinerlei Verbindung zwischen unserem Unternehmen und den genannten Marken. Es handelt sich bei dem angebotenen Artikel um originale fabrikneue Waren des Herstellers.
DCMT 11T304 AH725 Wendeplatten - Tungaloy
Take advantage of a robust, PVD-coated carbide grade that combines reliable chip control and wide material coverage for stable, repeatable turning; order directly via Metav Werkzeuge or consult our specialists for tailored toolholder and clamping options. DCMT 11T304 AH725 indexable turning insert — Tungaloy, PVD-coated carbide, 55° rhombic A DCMT11T304 AH725 indexable insert for external and internal turning, offering a 7° clearance angle and a one-sided chipbreaker for secure, process-stable machining. PVD-coated carbide grade AH725 Universal performance for Stahl and rostfreier Stahl Compatible with ISO holders, cylindrical hole + countersink Consistent process security for mixed-material turning The AH725 grade is a PVD-coated carbide designed to deliver consistent performance across a wide range of materials, making it particularly suitable where material mixes occur or where small tools must maintain stability. The coating reduces friction and resists built-up edge formation, which in turn helps to maintain cutting edge geometry under variable feed and speed conditions. For shops requiring predictable tool life and reduced regrinding intervals, this insert supports steady production rhythms and fewer unexpected tool changes. Geometry that ensures reliable clamping and stable cutting forces The rhombic geometry with a nominal 55° included angle and a 0.4 mm corner radius provides a balance between edge strength and accessibility for profile work. The 7° clearance angle lowers rubbing and improves surface finish while the specified hole style — cylindrical hole + single-sided countersink (40°–60°) — secures the insert in the seat and reduces micro-movement under heavy cuts. These geometric choices translate into more consistent results, less chatter and predictable cutting forces when the insert is combined with a properly matched holder. ISO compatibility and system-level efficiency As an ISO-standard indexable turning plate, compatibility with holders is determined by form, clearance angle, tolerance class, attachment method, size and thickness; this enables straightforward selection of a matching external holder or boring bar, plus backing/clamp sets and replacement screws. The standardised interface supports faster setup, fewer inventory variants and simpler tool management in multi-machine environments. Where quick changeovers and reduced tooling complexity are priorities, system integration of the insert reduces downtime and simplifies process planning. Why this grade is recommended for demanding turning tasks The single-sided chipbreaker and the PVD finish make this insert a solid choice for both finishing and light to medium roughing in Stahl and rostfreier Stahl. The composition emphasises fracture resistance and process security, which is beneficial in situations with variable workpiece batches or when operators require a robust, reliable cutting edge rather than constant adjustment. For applications that prioritise repeatability and machining quality, this indexable insert delivers measurable improvements in uptime and surface consistency. Contact Metav Werkzeuge for precise toolholder matching and fast supply of the Tungaloy DCMT11T304 AH725 insert — email info@metav-werkzeuge.com or call +49 2822 7131930 for expert advice and ordering support Technical data Article number: 6856709 SKU: 6856709-Tungaloy Manufacturer SKU: TUN6856709 Model series: ISO-Drehwendeschneidplatten Designation: DCMT11T304 Facts Size: 11 mm Thickness: 3.97 mm Clearance angle: 7° Included angle: 55° Corner radius: 0.4 mm Special features Material: carbide Coating / grade: AH725 (PVD-coated) Plate shape: rhombic Hole: cylindrical hole + single-sided countersink (40°–60°) Chipbreaker: one-sided Typical application: external and internal turning System components: insert, matching external holder or boring bar, backing/clamp set, replacement screws FAQ What materials is this insert suitable for? The AH725 grade insert is intended for machining Stahl and rostfreier Stahl and is specified for applications where fracture resistance and process security are required. How does the PVD coating benefit machining performance? The PVD coating on this Tungaloy insert increases surface hardness and reduces friction, which helps to prevent built-up edge and extends tool life under varied operating conditions. Which holders are compatible with this ISO designation? Compatibility is determined by form, clearance angle, tolerance class, attachment, size and thickness; the DCMT11T304 format fits standard ISO-compatible external holders and boring bars designed for 11 mm rhombic inserts. What does the hole style mean for clamping reliability? The cylindrical hole with a single-sided countersink (40°–60°) delivers secure seating and predictable clamping, reducing micro-movements and improving stability under load. Is this insert suitable for finishing and roughing operations? Yes — the single-sided chipbreaker and 0.4 mm corner radius make it adaptable for finishing and light to medium roughing, depending on cutting parameters and holder rigidity. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
DCMT 11T304 AH8005 Wendeplatten - Tungaloy
Take advantage of the PVD‑coated AH8005 grade and the rhombic DCMT11T304 geometry for stable machining of heat‑resistant alloys; the 0.4 mm corner radius and ISO compatibility ensure reliable edge strength and straightforward toolholder integration — order the insert directly via Metav Werkzeuge or contact our consultants for application advice. DCMT11T304 AH8005 Tungaloy turning insert — PVD‑coated carbide, rhombic 55° geometry The DCMT11T304 AH8005 is a rhombic, ISO‑standard indexable insert designed for external and internal turning of heat‑resistant alloys and hard materials, providing a wear‑resistant solution for stable machining operations. PVD-coated AH8005 grade for high wear resistance Rhombic DCMT shape, 55° cutting angle 0.4 mm corner radius for reliable edge strength Compatible with ISO turning toolholders, with hole Consistent wear resistance for demanding materials The PVD‑coated AH8005 grade combines a wear‑resistant coating with a tough carbide substrate to extend tool life in challenging conditions. This composition is especially suited to machining heat‑resistant alloys, where temperature and abrasion can rapidly degrade uncoated edges; the coating reduces flank wear and preserves the cutting edge, leading to fewer insert changes and more consistent component tolerances. The result is improved process reliability without sacrificing performance. Precise geometry for stable, repeatable turning With a 55° cutting angle and 0.4 mm corner radius, the insert delivers a balance between chip control and edge strength that benefits both finishing and light semi‑finishing passes. The 7° clearance reduces rubbing while maintaining support behind the cutting edge, decreasing vibration and ensuring consistent surface finish. These geometric choices translate to predictable cutting forces and help to maintain tool life under stable machining conditions. Easy integration into ISO tool systems The insert is an ISO‑standard rhombic form with a cylindrical hole with single‑sided countersink (40°–60°), enabling secure clamping in a wide range of holders and boring bars. The 3.97 mm thickness and size 11 footprint ensure compatibility with common external and internal turning toolholders, simplifying tool selection in mixed‑tool environments. Clear identification and standardised dimensions reduce setup time and help maintain reproducible clamping repeatability. Targeted chip control and application focus Engineered with a one‑sided chipbreaker, the DCMT11T304 is optimised for steady chip formation in applications where stability and surface integrity matter most. The chipbreaker and grade pairing promotes predictable swarf evacuation when cutting tougher materials, lowering the risk of built‑up edge and improving workpiece finish. For shops working with alloys requiring robust edges, this combination supports productive, repeatable machining cycles. For reliable, wear‑resistant turning choose Tungaloy’s AH8005 inserts — contact Metav Werkzeuge for ordering and technical advice at info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: 6747767 SKU: 6747767-Tungaloy Manufacturer SKU: TUN6747767 Model series: ISO-Drehwendeschneidplatten ISO designation: DCMT11T304 Facts Cutting angle: 55° Clearance angle: 7° Corner radius: 0.4 mm Thickness: 3.97 mm Size: 11 Special features PVD‑coated carbide grade AH8005 Rhombic insert shape (DCMT) One‑sided chipbreaker Cylindrical hole with single‑sided countersink (40°–60°) ISO‑standard indexable insert for turning Suited to heat‑resistant alloys and hard materials Compatible with ISO turning holders and boring bars FAQ What materials is this insert suitable for? The DCMT11T304 AH8005 insert is designed for heat‑resistant alloys and hard materials, using the AH8005 grade and PVD coating to improve wear resistance in such applications. Which insert geometry and angles does it feature? This rhombic insert has a 55° cutting angle, 7° clearance and a 0.4 mm corner radius, providing a compromise between edge strength and chip control for stable turning. How is the insert mounted in a toolholder? Mounting uses the ISO‑standard cylindrical hole with a single‑sided countersink (40°–60°); the form and tolerance class determine compatibility with corresponding ISO turning holders. What benefits does the AH8005 coating bring? The PVD‑coated AH8005 grade enhances wear resistance and thermal stability, which reduces flank wear and contributes to longer insert life in abrasive or high‑temperature cutting conditions. Is this insert suited for internal as well as external turning? Yes, the insert’s form and size make it suitable for both external and internal turning when paired with an appropriate ISO‑compatible holder or boring bar. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
DCMT 11T304 AH8005 Wendeplatten - Tungaloy
Combining PVD-coated carbide AH8005 with a rhombic 55° geometry and a 0.4 mm nose radius delivers durable wear performance and precise profiling for demanding turning operations; order the DCMT11T304 AH8005 Tungaloy insert directly via Metav Werkzeuge or consult our specialists for application support. DCMT11T304 AH8005 Tungaloy turning insert — ISO rhombic indexable insert with 7° clearance DCMT11T304 AH8005 Tungaloy insert is an ISO-standard indexable turning plate designed for stable external and internal turning of heat-resistant alloys and other hard materials Rhombic ISO insert DCMT11T304 PVD-coated carbide AH8005 grade 7° clearance angle for stable cutting 0.4 mm nose radius for fine profiling Durable grade for high-temperature and hard-material turning The AH8005 grade is a PVD-coated carbide developed for wear resistance in the machining of heat-resistant alloys and other hard workpiece materials. In stable setups this grade extends tool life through improved edge stability and reduced flank wear, which translates into fewer insert changes and more consistent production runs. The coating enhances resistance to adhesive and abrasive wear while preserving cutting-edge integrity during higher thermal loads. Geometry engineered for precision and surface quality The rhombic plate with a 55° included angle and 0.4 mm nose radius offers a balance between profile definition and cutting robustness. The moderate nose radius supports improved surface finish without compromising edge strength, while the 7° clearance ensures the rake and relief geometry reduce rubbing and heat build-up. The insert’s hole arrangement — a cylindrical bore with a single-sided countersink (40°–60°) — permits secure clamping and repeatable positioning in compatible holders. System compatibility and reliable fixture integration Supplied as part of the ISO turning insert system, the plate is compatible with matching external holders or boring bars when the form, clearance angle, tolerance class, clamping method, size and thickness correspond. The system typically comprises the insert, an appropriate outer holder or boring bar, a backing/clamping set and replacement screws. Choosing components from the same ISO family ensures repeatable seating, predictable run-out and consistent cutting conditions across multiple machining stations. Practical machining benefits and recommended applications Designed for both external and internal turning, the single-sided chipbreaker and AH8005 composition help control chip flow in continuous cuts and interrupted operations when stability is maintained. The combination of turning-optimised geometry and chipbreaker selection reduces rework and improves batch-to-batch consistency. For best results, pair the insert with a rigid setup and a holder matched to the insert thickness and size to exploit the stable machining characteristics and to secure reliable surface finish and extended tool life. For demanding turning tasks with heat-resistant alloys, specify the Tungaloy AH8005 DCMT11T304 through Metav Werkzeuge — contact Metav Werkzeuge for availability and application recommendations at info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: 6747770 Manufacturer SKU: TUN6747770 SKU: 6747770-Tungaloy Model series: ISO turning indexable inserts Material: Carbide Grade/coating: AH8005, PVD-coated Facts Size: 11 mm Thickness: 3.97 mm Nose radius: 0.4 mm Clearance angle: 7° Included angle: 55° Special features Rhombic shape With hole: cylindrical bore + single-sided countersink (40°–60°) One-sided chipbreaker Application: Turning (external and internal) System components: ISO insert, matching holder or boring bar, backing/clamping set, replacement screws Suited for heat-resistant alloys and hard materials FAQ Which materials is this insert suitable for? The DCMT11T304 AH8005 Tungaloy insert is formulated for machining heat-resistant alloys and other hard materials where a wear-resistant PVD-coated carbide provides sustained performance. Can this plate be used for internal turning as well as external turning? Yes, the insert’s rhombic geometry and single-sided chipbreaker make it suitable for both external and internal turning when combined with an appropriate boring bar or holder. What does the AH8005 designation indicate? AH8005 denotes a PVD-coated carbide grade optimised for wear resistance and edge stability under elevated temperatures and demanding cutting conditions. How does the 0.4 mm nose radius affect the machining result? A 0.4 mm nose radius balances surface finish and edge strength, delivering fine profiling while maintaining robustness against edge chipping in stable setups. How should compatibility with the holder be checked? Compatibility is determined by matching insert form, clearance angle, tolerance class, clamping method, size and thickness; using holders from the same ISO family ensures correct seating and repeatability. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
DCMT 11T304 AH8005 Wendeplatten - Tungaloy
Take advantage of the combination of wear-resistant carbide grade AH8005, a PVD-coated surface and a 0.4 mm corner radius to achieve stable chip formation and longer tool life in demanding turning operations; order directly via Metav Werkzeuge or consult our specialists for application-specific selection. DCMT 11T304 AH8005 Tungaloy turning insert — indexable insert for Turning DCMT11T304 AH8005 is an ISO-standard indexable turning insert designed for external and internal turning of heat-resistant alloys and hard materials. PVD-coated carbide grade AH8005 0.4 mm corner radius for robust cutting Rhomboid 55° geometry for versatile turning Cylindrical hole with single-side countersink 40°–60° Consistent metal removal with a wear-resistant carbide grade The PVD-coated carbide grade AH8005 provides enhanced resistance to abrasion and thermal loading, which translates into longer tool life and fewer indexings per component. The combination of a thin, hard coating and a substrate engineered for strength ensures reliable performance when machining heat-resistant alloys and other demanding materials. By choosing this grade, shops benefit from reduced tool changes and improved process uptime while maintaining consistent component quality. Secure clamping and geometry that supports stable turning As an ISO-standard indexable insert, compatibility with holders is governed by shape, clearance angle, tolerance class, clamping type, size, and thickness. The rhomboid form with a nominal 55° included angle and 7° clearance provides a balanced cutting edge suitable for a range of external and internal turning tasks. The insert’s cylindrical hole with a single-side countersink (40°–60°) enables precise clamping and repeatable positioning in a matching toolholder, reducing vibration and improving surface finish on the workpiece. Practical benefits for production efficiency and part quality A 0.4 mm corner radius offers a compromise between edge strength and surface finish: robust enough to withstand interrupted cuts and moderate depth of cut, yet fine enough to achieve acceptable surface quality without additional dressing. The 3.97 mm plate thickness and the one-sided chipbreaker design support controlled chip formation for stable cutting forces. Together, these attributes help to lower cycle times, decrease scrap rates and deliver predictable tool behaviour — factors that contribute directly to cost-effective machining in serial production. Contact Metav Werkzeuge for tailored recommendations on Tungaloy AH8005 inserts, specification matching or to request a technical quote via info@metav-werkzeuge.com or +49 2822 7131930 Technical data Article number: 6747776 Manufacturer SKU: TUN6747776 Manufacturer article number: 6747776 Manufacturer: Tungaloy Product name: DCMT11T304 AH8005 Tungaloy turning insert Core dimensions Size: 11 mm Plate thickness: 3.97 mm Corner radius: 0.4 mm Clearance angle: 7° Included angle: 55° Special features Rhomboid plate geometry Cylindrical hole with single-side countersink (40°–60°) PVD-coated carbide grade AH8005 One-sided chipbreaker ISO-standard turning indexable insert Application: Turning FAQ What materials can be machined with this insert? The DCMT11T304 AH8005 insert from Tungaloy is formulated for heat-resistant alloys and hard materials; the AH8005 grade and PVD coating improve wear resistance for these workpiece types. How does the 0.4 mm corner radius affect machining? A 0.4 mm radius increases edge strength compared with finer radii, helping to withstand interrupted cuts while still permitting good surface finish when using appropriate cutting parameters. Which holders are compatible with this ISO insert? Compatibility depends on matching the rhomboid form, 7° clearance, tolerance class, clamping method, size (11 mm) and thickness (3.97 mm); use a holder or boring bar specified for ISO DCMT-style inserts. Is the insert reversible or indexable? The component is an indexable insert designed for indexing; the one-sided chipbreaker and hole/clamping arrangement allow for secure replacement and repeatable positioning. What fastening method is recommended for stable clamping? Use a compatible clamping set with the appropriate screw and shim for DCMT geometry; the cylindrical hole and single-side countersink (40°–60°) ensure centring and firm clamping in the correct holder. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
DCMT 11T304 AH8015 Wendeplatten - Tungaloy
Benefit from a combination of reliable wear resistance and stable cutting-edge performance thanks to the AH8015 PVD-coated carbide and the ISO 55° rhombic geometry; order the DCMT11T304 directly via Metav Werkzeuge or ask our consultants if needed. DCMT11T304 AH8015 – ISO rhombic turning insert, PVD-coated carbide by Tungaloy The DCMT11T304 AH8015 is an ISO rhombic turning insert designed for general external and internal turning, especially suited to heat-resistant alloys. ISO rhombic insert DCMT11T304, 55° cutting angle PVD-coated carbide grade AH8015 for hot alloys 0.4 mm corner radius for precise finishes One-sided chipbreaker for controlled chips Countersunk hole for secure clamping Consistent tool life through a balanced carbide grade The combination of PVD coating and a wear-resistant carbide substrate in grade AH8015 delivers a balanced trade-off between abrasion resistance and edge stability. This balance reduces unplanned tool changes and contributes to a more predictable process where indexable inserts are part of a production cycle. The coating enhances heat resistance during elevated cutting temperatures, making the insert suitable for machining heat-resistant and high-temperature alloys while maintaining surface quality and extended edge life. Geometry engineered for precision and secure clamping A 55° rhombic geometry with a 0.4 mm corner radius is optimised for accurate finishing and repeatable dimensional control in turning operations. The plate thickness of 3.97 mm and the integrated countersunk hole (cylindrical hole with a single-sided countersink at 40°–60°) ensure secure clamping and stable seat engagement in ISO-standard toolholders. Correct matching of holder form, clearance angle, tolerance class and fastening hardware preserves the insert’s positional accuracy and reduces chatter, thus improving surface finish and tolerance adherence. Controlled chip flow and versatile application scope A one-sided chipbreaker provides reliable chip control for a wide range of feeds and depths of cut, simplifying post-process handling and reducing the risk of chip entanglement in automated centres. The insert is part of an ISO-indexable system that typically includes a compatible external holder or boring bar, a shim/clamping set and replacement screws, enabling straightforward integration into established turning setups. Its intended application is general turning of heat-resistant alloys and similar demanding materials where a mix of process security and economy is required. For dependable turning performance with Tungaloy’s AH8015 grade, contact Metav Werkzeuge for availability and technical advice: info@metav-werkzeuge.com or +49 2822 7131930 Technical Data Article number: 6825767 SKU: 6825767-Tungaloy Manufacturer SKU: TUN6825767 Manufacturer article number: 6825767 Facts Insert size: 11 mm Plate thickness: 3.97 mm Corner radius: 0.4 mm Clearance angle: 7° Cutting angle: 55° Special features Material: carbide Grade/coating: AH8015, PVD-coated Shape: rhombic ISO insert Chipbreaker: one-sided Mounting: with hole; cylindrical hole + single-sided countersink (40°–60°) Application: turning Series: ISO turning inserts FAQ What materials is this insert suitable for? The DCMT11T304 AH8015 Tungaloy turning insert is formulated for heat-resistant alloys and similar challenging materials, the AH8015 grade providing a balance of wear resistance and edge stability. Is this insert compatible with standard ISO holders? Yes, the insert follows ISO dimensions; compatibility depends on matching the holder’s form, clearance angle, tolerance class, fastening method, size and thickness. How does the chipbreaker affect machining? The one-sided chipbreaker on this insert promotes controlled chip formation and evacuation, reducing the likelihood of chip interference in both manual and automated turning operations. What clamping method is required for secure seating? The insert features a cylindrical hole with a single-sided countersink (40°–60°), which is designed for secure clamping when used with the correct clamp/shim and screw assembly in ISO-standard holders. Can this insert be used for both external and internal turning? Yes, the rhombic geometry and robust grade make it suitable for both external and internal turning applications when paired with the appropriate holder or boring bar. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
DCMT 11T304 AH8015 Wendeplatten - Tungaloy
Benefit from the combination of a PVD-coated carbide grade that balances wear resistance and edge stability, a 55° rhombic geometry for robust cutting, and a precise 0.4 mm nose radius for fine finishes — ideal for productive turning of heat‑resistant alloys. Order the DCMT11T304 AH8015 insert directly via Metav Werkzeuge or consult our advisers for application support. DCMT 11T304 AH8015 ISO rhombic turning insert, 55° lead angle — Tungaloy DCMT11T304 AH8015 is an ISO‑standardised rhombic turning insert designed for external and internal turning of heat‑resistant alloys and general-purpose turning applications PVD-coated carbide grade AH8015 ISO rhombic insert, 55° lead angle 0.40 mm nose radius for fine detail Single-sided chipbreaker with hole Reliable performance with heat‑resistant materials The PVD-coated carbide grade AH8015 delivers a deliberate balance between wear resistance and edge stability, making it well suited to turning difficult, heat‑resistant alloys where thermal load and abrasion are critical. The rhombic 55° geometry provides a robust cutting edge for general turning tasks while the modest 0.4 mm nose radius supports improved surface quality without sacrificing tool life. In practice this combination reduces tool changes and keeps cycle times predictable, which supports steady production throughput and cost efficiency. Consistent surface quality and controlled chip formation A carefully designed, single‑sided chipbreaker encourages predictable chip control and helps to avoid rework from imperfect swarf evacuation. The insert’s geometry and chipbreaker pairing are intended to produce consistent surface finishes on external and light internal turning operations, reducing downstream finishing requirements. As an ISO‑standard insert, compatibility with established holders is straightforward, allowing straightforward integration into existing tool systems while maintaining the process reliability expected in industrial turning operations. Secure mounting and system compatibility The insert is supplied with a hole, featuring a cylindrical bore plus a one‑sided countersink (40°–60°), to match common clamping systems and ensure repeatable seating and torque behaviour. With a plate thickness of 3.97 mm and ISO dimensions, the insert’s fit is governed by form, relief angle and tolerance class; selecting the correct external holder or boring bar guarantees optimal force transmission and minimises vibration. These mechanical characteristics contribute directly to repeatable part tolerances and longer indexable life. Productivity and predictable tool life for busy workshops Choosing this grade and geometry supports process stability: the balanced substrate and coating combination aims to extend usable life under varying cutting conditions, while the standardised ISO format simplifies inventory management. The design reduces interruptions caused by unexpected tool wear and supports a rational maintenance schedule, encouraging higher machine availability. Together, these technical strengths improve machining reliability and contribute to more predictable manufacturing costs and throughput. Request tailored application advice from Metav Werkzeuge for the DCMT11T304 AH8015 turning inserts — email info@metav-werkzeuge.com or call +49 2822 7131930 to discuss quantities and holder compatibility Technical data Article number: 6825790 SKU: 6825790-Tungaloy Manufacturer SKU: TUN6825790 Model series: ISO‑Drehwendeschneidplatten Grade: AH8015 Facts Size: 11 mm Plate thickness: 3.97 mm Nose radius: 0.4 mm Lead angle: 55° Relief angle: 7° Hole style: cylindrical hole + one‑sided countersink (40°–60°) Special features Material: carbide Coating: PVD Plate shape: rhombic Chipbreaker: single‑sided Application: Turning ISO‑standard insert (DCMT11T304) FAQ What materials is this insert suitable for? The DCMT11T304 AH8015 Tungaloy turning insert is intended primarily for heat‑resistant alloys and general turning applications; its PVD‑coated carbide composition provides a balanced wear resistance and edge stability for these materials. Can the insert be used for both external and internal turning? Yes. The ISO rhombic geometry and single‑sided chipbreaker make the insert suitable for external turning and light internal turning operations when paired with a compatible holder. How does the chipbreaker affect machining? A single‑sided chipbreaker on this insert promotes controlled chip formation and evacuation, improving surface finish and reducing the likelihood of chip entanglement in turning operations. Which holders are compatible with this ISO insert? Compatibility depends on holder form, relief angle, tolerance class, fastening method, size and thickness; the ISO designation and the insert’s hole/countersink ensure it fits standard ISO‑compatible turning holders when matched correctly. What does the hole and countersink specification mean for clamping? The cylindrical hole with a one‑sided countersink (40°–60°) provides positive location and repeatable clamping; this improves seating stability and repeatability across indexings. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand‑new product from the manufacturer.
DCMT 11T304 AH8015 Wendeplatten - Tungaloy
Take advantage of the proven combination of PVD-coated carbide wear resistance, stable edge performance and a precise rhombic 55° geometry to maintain a smooth turning process; order directly via Metav Werkzeuge or request application advice from our consultants. DCMT11T304 AH8015 indexable turning insert — PVD-coated carbide, rhombic 55° geometry, Tungaloy A DCMT11T304 AH8015 indexable insert engineered for efficient external and internal turning of heat-resistant alloys, offering a balanced compromise between wear resistance and edge stability. DCMT11T304 ISO turning insert by Tungaloy PVD-coated carbide grade AH8015 Rhombic 55° geometry with 7° clearance Single-sided chipbreaker and 0.4 mm radius High-performance grade for heat-resistant alloys The AH8015 grade is a PVD-coated carbide developed as a first-choice solution for general machining of heat-resistant alloys, combining wear resistance with reliable cutting-edge stability. The coating process increases resistance to temperature-related abrasion, which preserves the cutting edge during higher cutting speeds. Conformity with ISO geometry ensures interchangeability within standard tool systems; compatibility with a holder is determined by form, clearance, tolerance class, fastening, size and thickness and should be checked before assembly. Geometry and chip control that improve surface finish A rhombic 55° insert angle, together with a 7° clearance, delivers favourable cutting forces and access to narrow features, while the single-sided chipbreaker promotes controlled chip formation under a range of cutting conditions. The 0.4 mm corner radius reduces edge chipping in interrupted cuts and supports consistent surface quality on both external and internal profiles. These geometry choices translate into fewer reworks and more predictable finishing results for demanding components. Clear mounting specification for efficient set-up The insert is supplied with a cylindrical fixing hole and a one-sided countersink (40°–60°), enabling secure and repeatable clamping in compatible holders. The plate thickness of 3.97 mm and plate size of 11 mm correspond to common ISO holders, simplifying stock management in production environments. The tool system comprises the indexable insert, the appropriate external holder or boring bar, a support/clamping kit and spare screws, which together form a stable assembly tailored to the selected application. Long tool life through balanced material and design Combining a robust cemented carbide substrate with a modern PVD finish, this insert is designed for consistent tool life and economical productivity in serial production. The grade’s balance between toughness and hardness helps to avoid premature flank wear while maintaining a stable cutting edge. Choosing the correct chipbreaker and grade in relation to workpiece stability and machining method will extend service intervals and reduce tooling costs per component. Contact Metav Werkzeuge for tailored application guidance on Tungaloy AH8015 inserts and specification support for turning tasks Technical data Article number: 6747771-Tungaloy Manufacturer SKU: TUN6747771 Manufacturer article number: 6747771 Model series: ISO indexable turning inserts Numbers / Core technical data Corner radius: 0.4 mm Included angle: 55° Clearance angle: 7° Plate thickness: 3.97 mm Plate size: 11 mm Special features / Versions Grade / coating: AH8015, PVD-coated carbide Chipbreaker: single-sided Fixing: with hole; cylindrical hole + one-sided countersink (40°–60°) Plate form: rhombic Typical application: turning (external and internal) System components: insert, holder/boring bar, support/clamping set, spare screws FAQ What materials is this insert suited for? The AH8015 grade insert is intended primarily for heat-resistant alloys; the DCMT11T304 AH8015 performs well where a balance of wear resistance and edge stability is required. Is the insert compatible with standard ISO holders? Yes, the geometry conforms to ISO indexable insert standards and can be used with compatible holders that match form, clearance, tolerance, fastening, size and thickness. How does the chipbreaker affect machining? The single-sided chipbreaker on this insert promotes controlled chip formation and can improve surface finish and swarf evacuation when matched to the workpiece and machining parameters. What are the mounting details for the insert? The insert is supplied with a cylindrical fixing hole and a one-sided countersink (40°–60°) and requires a holder that accommodates this fixing style for secure clamping. Can the radius be used for finishing? The 0.4 mm corner radius offers a compromise between strength and finishing capability, making it suitable for many semi-finish and finish turning operations. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
DCMT 11T304 AH8015 Wendeplatten - Tungaloy
Reliable machining assured by the combination of PVD‑coated AH8015 carbide and a 0.4 mm corner radius, delivering stable cutting performance across heat‑resistant alloys; conformity with ISO holder standards ensures straightforward integration. Order the insert directly via Metav Werkzeuge or consult their specialists for application guidance. DCMT11T304 AH8015 ISO turning insert — rhombic 55° lead angle by Tungaloy The DCMT11T304 AH8015 is an ISO‑standard rhombic insert designed for external and internal turning of heat‑resistant alloys, offering balanced wear resistance and edge stability for productive machining. PVD-coated carbide AH8015 for heat-resistant alloys 0.4 mm corner radius for precise finishing ISO rhombic insert with 55° lead angle Engineered cutting performance for heat‑resistant alloys The insert is manufactured from PVD‑coated carbide, a combination that provides an advantageous balance between wear resistance and edge stability for demanding materials. The chosen coating and grade are particularly suited to work on heat‑resistant alloys where thermal loads are high; this means more consistent tool life under cyclic thermal stress and fewer unplanned tool changes. The construction follows ISO norms, so compatibility with standard turning systems is ensured and tool management becomes more predictable for production planning. Geometry tuned for consistent surface quality Precision geometry translates directly into repeatable part quality: the 0.4 mm corner radius and 7° clearance angle promote reliable finishing without excessive cutting forces, while the 55° lead angle and rhombic form support versatile approach angles for both external and internal operations. The insert’s 3.97 mm thickness and the central hole with cylindrical bore plus a one‑sided countersink (40°–60°) secure stable clamping and repeatable seating in appropriate holders. Describing the insert’s form and fixation helps machinists select the correct mating components and reduces setup variability on the shop floor. Practical benefits, chip control and system fit A single‑sided chipbreaker design provides effective chip control for a broad range of feeds and depths, reducing rework and protecting the cutting edge from chip interference. As a member of an ISO‑based insert system, the component integrates with a matching external holder, shim or clamp set and replacement screws — a full system approach that simplifies inventory and maintenance. Together these technical choices contribute to higher process reliability and predictable cycle times, supporting both single‑piece manufacturing and serial production. Contact Metav Werkzeuge for tailored application advice and to source the appropriate Tungaloy DCMT11T304 insert — phone +49 2822 7131930 or email info@metav-werkzeuge.com Technical data Article number: 6747777 Manufacturer SKU: TUN6747777 Label: DCMT11T304 AH8015 Tungaloy‑insert Facts Size: 11 Thickness: 3.97 mm Corner radius: 0.4 mm Clearance angle: 7° Lead/approach angle: 55° Hole: with hole; cylindrical hole + one‑sided countersink (40°–60°) Form: rhombic Chipbreaker: single‑sided Material/coating: PVD‑coated carbide (AH8015) Special features ISO turning insert series for external and internal turning Compatible with ISO‑standard holders (shape, clearance, tolerance, fastening, size and thickness determine compatibility) Designed for heat‑resistant alloys and broad material coverage System components: matching external holder, shim/clamp set, replacement screws FAQ What materials is this insert intended for? The DCMT11T304 AH8015 insert is specified as a first choice for machining heat‑resistant alloys and provides a balanced compromise between wear resistance and cutting‑edge stability for a wide range of alloyed materials. Which toolholders fit this insert? Compatibility depends on holder shape, clearance angle, tolerance class, fastening method, size and thickness; the insert conforms to ISO standards, simplifying selection of a matching external holder and clamping components. How does the 0.4 mm corner radius affect part finish? A 0.4 mm corner radius offers improved surface integrity and edge life during finishing and semi‑finishing operations, helping to produce consistent surface quality with reduced risk of small chipping at the corner. Is there a chip control solution with this geometry? Yes, the single‑sided chipbreaker integrated in the insert geometry supports controlled chip formation across common feeds and depths, reducing the likelihood of chip entanglement and assisting automated material evacuation. What fastening features does the insert offer? The insert is supplied with a central cylindrical hole and a one‑sided countersink (40°–60°) to ensure secure and repeatable seating in compatible clamping systems Manufacturer/Responsible: Tungaloy‑NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand‑new product from the manufacturer.
DCMT 11T304 AH8015 Wendeplatten - Tungaloy
Take advantage of the combination of PVD-coated carbide performance, precise 55° rhombic geometry and secure mounting features for consistent turning results; order the DCMT11T304 AH8015 insert via Metav Werkzeuge or consult the technical team for application-specific guidance. DCMT11T304 AH8015 — ISO indexable turning insert for general turning, 55° rhombic, PVD-coated (Tungaloy) The DCMT11T304 AH8015 is an ISO rhombic indexable insert engineered for external and internal turning of heat‑resistant alloys and similar demanding materials, providing a balanced combination of wear resistance and cutting‑edge stability. ISO rhombic 55° geometry PVD-coated carbide AH8015 7° clearance for reliable edges Single-sided chipbreaker design Stable cutting with the correct geometry for turning The rhombic 55° geometry delivers a favourable tool approach angle for a wide range of turning tasks, improving force distribution and tool life during both roughing and finishing operations. The 7° clearance reduces rubbing on the flank face, which helps maintain cutting‑edge integrity and consistent surface finish. A 0.4 mm corner radius promotes edge robustness where light cutting and profile accuracy are required. These geometric characteristics combine to reduce vibration and rework, supporting more predictable cycle times and lower scrap rates. Coating and grade optimised for heat‑resistant alloys The insert is made from carbide and features a PVD‑coating in the AH8015 grade, selected as a first choice for the general machining of heat‑resistant alloys. This combination offers a sensible compromise between wear resistance and edge stability, extending tool life under elevated temperatures while preserving dimensional accuracy. For less experienced staff, the grade simplifies grade selection: AH8015 is suited to applications where temperature endurance and stable chip formation are priorities rather than extreme cutting speeds. System compatibility and practical process benefits Compatibility with clamping systems depends on form, clearance, tolerance class, fixing method, size and thickness; the ISO standard designation ensures broad interchangeability with holders and boring bars designed for rhombic inserts. The insert’s single-sided chipbreaker supports controlled chip flow for many common turning operations, while the cylindrical hole with single‑side countersink (40°–60°) simplifies secure clamping. In practice, this means shorter tool change routines, fewer set‑up adjustments and improved uptime for production runs in job shops and OEM operations alike. If exact machining parameters are required for a specific alloy, Metav Werkzeuge’s application data can be consulted. Contact Metav Werkzeuge for tailored cutting data and rapid availability of the DCMT11T304 AH8015 Tungaloy indexable insert — eMail: info@metav-werkzeuge.com, Tel: +49 2822 7131930 Technical data Article number: 6746101 SKU: 6746101-Tungaloy Manufacturer SKU: TUN6746101 Model series: ISO indexable turning inserts Designation: DCMT11T304 AH8015 Manufacturer: Tungaloy Facts Insert size: 11 mm Thickness: 3.97 mm Clearance angle: 7° Lead/approach angle: 55° Corner radius: 0.4 mm Special features PVD-coated carbide (AH8015) Rhombic insert shape Single-sided chipbreaker Cylindrical hole + single-side countersink (40°–60°) Suitable for external and internal turning ISO-standard compatibility; holder matching by form, clearance, tolerance, fixing, size and thickness FAQ Which materials are suitable for this insert? The DCMT11T304 AH8015 Tungaloy indexable insert is optimised for heat‑resistant alloys and similar high‑temperature materials; the AH8015 PVD‑coated carbide grade provides a balance of wear resistance and edge stability for general turning tasks. Can this insert be used for internal turning and external turning? Yes — the insert’s rhombic 55° geometry and chipbreaker design make it suitable for both external and internal turning applications when paired with an appropriate external holder or boring bar. How does the insert secure to the holder? The insert uses a central cylindrical hole with a single‑side countersink (40°–60°) for secure clamping; compatibility with a specific holder depends on matching form, clearance, tolerance class, fixing method, size and thickness. What advantages does the AH8015 coating deliver? The AH8015 PVD coating increases resistance to thermal wear while preserving cutting‑edge stability, resulting in longer service life under elevated temperatures and more consistent surface quality. What insert dimensions and angles are critical for setup? Key measurable data for setup are: insert size 11 mm, thickness 3.97 mm, clearance angle 7°, lead/approach angle 55°, and corner radius 0.4 mm; confirm these values against the holder specifications before mounting. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
DCMT 11T304 AH905 Wendeplatten - Tungaloy
Take advantage of the combination of a PVD‑coated carbide AH905 grade and a rhombic DCMT 55° geometry to secure consistent cutting performance and process reliability in turning operations. The compact 3.97 mm thickness and 0.4 mm corner radius provide stability and versatility for common external and internal turning tasks. Order supply or request tailored advice via Metav Werkzeuge for immediate availability and application guidance. DCMT 11T304 AH905 indexable turning insert — Tungaloy for turning The DCMT11T304 AH905 is an ISO‑standard rhombic indexable insert for external and internal turning, designed to deliver a sharp, wear‑resistant cutting edge and dependable process security. PVD‑coated carbide AH905 Rhombic DCMT 55° geometry 0.4 mm corner radius Single‑sided chipbreaker, with hole Consistent cutting performance and process security The AH905 grade is a PVD‑coated carbide engineered to combine wear resistance with an edge geometry suited to stable metal removal. The result is predictable tool life and controlled flank wear, reducing unplanned interruptions. Paired with the rhombic 55° insert geometry, the design balances cutting forces and provides accessible cutting edges for a range of turning set‑ups. This delivers measurable productivity benefits: fewer insert changes and more consistent part quality during serial machining. Clear guidance on compatibility and clamping As an ISO‑standard insert, compatibility with holders depends on matching form, clearance angle, tolerance class, fastening method, size and thickness. The insert features a cylindrical centre hole with a single‑sided countersink (40°–60°) for secure clamping and reliable seat location. The 7° relief angle contributes to predictable cutting engagement, while the 3.97 mm thickness supports rigidity in light to medium‑duty turning. These measurable parameters simplify selection of a suitable external holder or boring bar. Application scope and practical recommendations Designed for general turning, the insert is suitable for both external and internal turning where a sharp cutting edge and process reliability are required. The single‑sided chipbreaker is matched to the grade to promote stable chip formation under appropriate cutting conditions. For best results, select the chipbreaker and cutting parameters according to workpiece material, machine stability and desired surface finish; the insert’s geometry and grade provide a robust baseline for common workshop and production applications. Handling, economy and logistical advantages A 0.4 mm corner radius offers a compromise between edge strength and finishing capability, enabling single‑insert versatility across multiple operations. The modest thickness of 3.97 mm contributes to a compact insert profile that is straightforward to seat and replace, helping to reduce changeover times. With its PVD coating the insert typically sustains edge integrity for longer periods, which can lower per‑part tooling costs and simplify inventory planning in production environments. For Tungaloy quality in turning applications, contact Metav Werkzeuge for technical matching and immediate supply of DCMT11T304 AH905 inserts Technical data Article number: 6879341 SKU: 6879341‑Tungaloy Manufacturer SKU: TUN6879341 Brand: Tungaloy Designation: DCMT11T304 AH905 indexable turning insert Facts Insert size: 11 mm Thickness: 3.97 mm Corner radius: 0.4 mm Relief angle: 7° Included angle: 55° Special features Material: carbide Coating / grade: PVD‑coated AH905 Shape: rhombic (DCMT geometry) Centre hole: cylindrical hole + single‑sided countersink (40°–60°) Chipbreaker: single‑sided Application: turning (external and internal) ISO‑standard indexable insert FAQ What machining tasks is this insert best suited for? The DCMT11T304 AH905 indexable insert is intended for general external and internal turning where a sharp, wear‑resistant edge and stable chip control are desired. How does the AH905 grade affect tool life? AH905’s PVD coating improves wear resistance and helps preserve the cutting edge, so the insert typically offers extended performance compared with uncoated grades under comparable conditions. Which holders are compatible with this insert? Compatibility depends on matching form, clearance angle, tolerance class, fastening and size; the insert’s cylindrical centre hole with countersink enables secure clamping in appropriately rated external holders and boring bars. What does the 0.4 mm corner radius mean for finish and strength? A 0.4 mm corner radius balances edge robustness with surface finish capability, making the insert versatile for turning operations that require moderate strength and acceptable surface quality. Can this insert be used for fine finishing operations? Yes, within the limits of its geometry and grade the insert can achieve good finishes; for demanding finishing applications, adjust feeds and speeds and consider a smaller corner radius if available. Manufacturer/Responsible: Tungaloy‑NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand‑new product from the manufacturer.
DCMT 11T304 AH905 Wendeplatten - Tungaloy
Benefit from the combination of a PVD-coated carbide grade AH905, a rhombic 55° geometry and a precise 0.4 mm corner radius for reliable machining and extended tool life; order the insert directly via Metav Werkzeuge or consult the team for application advice. DCMT 11T304 AH905 – ISO rhombic turning insert for external and internal turning, PVD-coated carbide by Tungaloy The DCMT11T304 AH905 is an ISO-standard rhombic insert designed for precision external and internal turning, combining a sharp cutting edge with a wear- and fracture-resistant PVD coating for process-secure production. PVD-coated carbide AH905 grade Rhombic 55° geometry, 0.4 mm radius Single-sided chipbreaker for controlled chips Cylindrical hole with 40°–60° countersink Predictable machining through a wear-resistant grade The PVD-coated carbide in grade AH905 is engineered for consistent performance where a sharp, durable cutting edge and resistance to chipping are essential. The coating improves surface hardness and reduces adhesive wear, which leads to more stable cutting conditions and fewer interruptions for edge changes. For demanding turning cycles this results in a measurable increase in process reliability, with the insert delivering steady edge life under typical steels and alloyed materials used in production environments. Secure seating and accurate geometry for repeatable results The rhombic 55° geometry with a 0.4 mm corner radius and a relief angle of 7° ensures a predictable engagement with the workpiece and reliable clearance during feed motion. The ISO designation and standardised form mean that compatibility with holders depends on form, relief angle, tolerance class, fixing method, size and thickness; ensuring the correct matching holder and clamping components avoids runout and optimises surface finish. Features such as the cylindrical hole with a one-sided countersink (40°–60°) support secure clamping and accurate indexing when exchanging edges. Efficient application planning and system assembly Intended for both external and internal turning, the insert works best when the single-sided chipbreaker is selected to match material, machining strategy and rigidity. In practice, the cutting system comprises the ISO insert, a suitable external holder or boring bar, a shim/clamping set and replacement screws — a configuration that supports fast insert changes and minimal downtime. Choosing the appropriate chipbreaker and cutter grade reduces cycle time and contributes to better cost-efficiency over the tool life, helping to maintain throughput in series production. Contact Metav Werkzeuge for availability, technical recommendations and order handling — eMail: info@metav-werkzeuge.com or call +49 2822 7131930 Product data Article number: 6879334 SKU: 6879334-Tungaloy Manufacturer SKU: TUN6879334 Manufacturer: Tungaloy Core data ISO designation: DCMT11T304 Size: 11 mm Thickness: 3.97 mm Corner radius: 0.4 mm Relief angle: 7° Cutting angle: 55° Special features PVD-coated carbide AH905 Rhombic plate form With hole Cylindrical hole + one-sided countersink (40°–60°) Single-sided chipbreaker Suitable for external and internal turning ISO-standard insert System components: insert, holder/boring bar, shim/clamping set, replacement screws FAQ Which materials can be machined with this insert? The DCMT11T304 AH905 Tungaloy insert is suitable for a broad range of materials; the PVD-coated carbide grade offers good performance on steels and many alloyed materials when combined with an appropriate cutting data and chipbreaker. What advantages does the AH905 grade bring to turning operations? AH905 provides increased wear resistance and fracture toughness; the PVD coating enhances surface hardness and adhesion resistance, which together improve edge life and process security for turning operations. How does the single-sided chipbreaker affect chip control? A single-sided chipbreaker promotes predictable chip formation for many turning tasks; selecting the correct chipbreaker profile and matching it to material and rigidity yields cleaner chips and reduced risk of surface damage. How is compatibility with holders ensured? Compatibility is determined by plate form, relief angle, tolerance class, fixing method, size and thickness; the ISO designation DCMT11T304 helps identify matching external holders or boring bars and the necessary clamping components. Is the insert indexed for multiple cutting edges? The rhombic ISO-design insert provides indexed cutting edges; correct clamping with the specified hole and countersink geometry ensures reliable indexing and repeatable positioning for edge changes. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
DCMT 11T304 AH905 Wendeplatten - Tungaloy
Benefit from the combination of a PVD-coated carbide AH905 grade that resists wear and chipping, and the ISO rhombic DCMT geometry with a 0.4 mm corner radius and 7° clearance for consistent turning performance. Order the insert directly via Metav Werkzeuge or consult our advisors for application-specific guidance. DCMT11T304 AH905 ISO turning insert — Turning — Tungaloy The DCMT11T304 AH905 is an ISO-compliant rhombic turning insert designed for external and internal turning, offering a single-sided chipbreaker and a secure clamping interface. PVD-coated carbide AH905 ISO rhombic DCMT geometry 0.4 mm corner radius for finishing Cylindrical hole with 40°–60° countersink Predictable compatibility and concise system build for ISO tooling The insert follows the ISO indexable plate system and the rhombic DCMT geometry, which provides a 55° included angle suited to typical turning applications. Compatibility with a respective holder is determined by plate form, clearance angle (7°), tolerance class, attachment style, size and thickness; this standardisation reduces setup time and simplifies tool inventory. The technical fit ensures a reproducible seating and repeatable tool offsets, supporting stable cycle times and easier tool management on the shop floor. Durable cutting edge through PVD coating and robust carbide The AH905 grade combines a PVD-coated surface with a carbide substrate to extend tool life where a sharp edge and process security are required. The coating reduces abrasive wear and improves thermal resistance, while the substrate grants toughness to resist chipping. As a result, operators obtain longer uninterrupted cutting intervals and more consistent surface quality, which lowers downtime and contributes to predictable machining costs. Application-focused performance for external and internal turning Designed with a single-sided chipbreaker, this insert supports controlled chip formation in a range of turning tasks. The modest 0.4 mm corner radius balances edge strength and surface finish: smaller radii improve finish quality, while the carbide base preserves edge stability under interrupted cuts. The plate is therefore appropriate when process reliability and a precise edge are priorities, and it adapts well to varying feed rates and depths of cut within standard turning operations. Mounting and handling that prioritise secure clamping and serviceability The plate is supplied with a cylindrical hole and a single-sided countersink (40°–60°) to ensure positive clamping in compatible ISO holders or boring bars; correct seating prevents micro-movements that can degrade finish and shorten life. The 3.97 mm plate thickness and 11 mm inscribed size correspond to common nose geometries and toolholder portfolios, allowing straightforward replacement without complex rework. Replacement screws and clamping sets follow the same ISO conventions, enabling fast tool changes and low operator learning curves. For tailored machining advice and rapid supply of the DCMT11T304 AH905 insert, contact Metav Werkzeuge via info@metav-werkzeuge.com or call +49 2822 7131930 for availability and application recommendations Technical Data Article number: 6879337 SKU: 6879337-Tungaloy Manufacturer SKU: TUN6879337 Brand: Tungaloy Model series: ISO turning indexable inserts Product designation: DCMT11T304 AH905 Key measurements Included angle: 55° Clearance angle: 7° Corner radius: 0.4 mm Plate thickness: 3.97 mm Inscribed size: 11 mm Countersink angle: 40°–60° Features & materials PVD-coated carbide AH905 Rhombic plate form (DCMT) Single-sided chipbreaker Cylindrical hole with single-side countersink For external and internal turning Compatibility determined by form, clearance angle, tolerance, size, thickness Sharp cutting edge with process-focused grade FAQ What is the main benefit of the AH905 grade? The AH905 grade provides a PVD-coated carbide construction that combines wear resistance with fracture toughness, making the DCMT11T304 AH905 insert (SKU 6879337-Tungaloy) suitable when a sharp cutting edge and process security are required. Which holder types are compatible with this insert? Compatibility is based on the ISO DCMT geometry and the plate’s dimensions; the insert works with ISO rhombic external holders or boring bars that accept an 11 mm inscribed size and a 3.97 mm plate thickness, using the cylindrical hole and countersink for secure clamping. How does the 0.4 mm corner radius affect machining? A 0.4 mm corner radius offers a compromise between surface finish and edge strength: it helps achieve a finer finish while maintaining sufficient edge toughness for many turning operations. Is the insert suitable for interrupted cuts or heavy machining? The combination of a robust carbide substrate and the AH905 coating enhances resistance to chipping and wear; however, final suitability depends on cutting parameters and holder rigidity, so select the chipbreaker and grade in line with the process demands. What are the mounting details for secure clamping? The plate features a cylindrical hole with a single-sided countersink (40°–60°) to ensure reproducible seating and reliable clamping in compatible ISO holders, reducing the risk of micro-movement during cutting. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
DCMT 11T304 AT9530 Wendeplatten - Tungaloy
Take advantage of the combination of a coated cermet grade AT9530, a 0.4 mm nose radius and ISO compatibility for consistently high surface quality and even tool wear; order the insert directly via Metav Werkzeuge or consult our specialists for application advice. DCMT11T304 AT9530 ISO rhombic turning insert for finishing, Tungaloy The DCMT11T304 AT9530 is an ISO rhombic turning insert designed for finishing and light turning of steel with a focus on surface quality and predictable wear ISO rhombic insert, DCMT form Coated cermet grade AT9530 0.4 mm nose radius for fine finishes 7° clearance; cylindrical hole with countersink Achieve superior surface finish with a coated cermet grade The insert employs a coated cermet specification AT9530, developed for finishing and light machining of steel where surface integrity matters. The composition balances ceramic hardness and metallic toughness to reduce flaking and promote uniform wear across the cutting edge. This results in longer intervals between index changes and a consistently improved surface finish, especially on external and internal turning operations that demand close tolerances and fine surface texture. The cermet coating also supports stable performance at finishing feeds and moderate cutting speeds. Confident compatibility with ISO toolholder systems Compatibility with toolholders is governed by geometric and dimensional standards: insert form, clearance angle, tolerance class, attachment method, size and thickness. The rhombic insert follows established ISO dimensions so it mates reliably with matching clamping systems. Correct pairing ensures the insert seats correctly and the specified clearance angle is maintained, reducing chatter and improving reproducibility. Where vibration dampening or added rigidity is required, selecting an appropriate external holder or boring bar and a correctly rated clamping set will preserve edge life and process stability. Geometry and clamping designed for stable finishing cuts The rhombic plate with a 55° principal angle and a 0.4 mm nose radius gives a precise contact geometry that favours fine cutting action and low cutting forces. The plate thickness of 3.97 mm contributes axial and radial rigidity when clamped in a suitable holder, while the single-sided chipbreaker helps control chip flow for finishing feeds. The insert is manufactured with a cylindrical hole and a one-sided countersink (40°–60°) to ensure secure and repeatable clamping; this design supports predictable cutting behaviour and eases index changes during production. Practical selection and system notes for efficient machining For reliable outcomes, choose a chipbreaker and grade matched to workpiece material, machining style and machine stability. The grade AT9530 is optimised for consistent edge condition during finishing of steel; a different chipbreaker or a more robust grade should be selected for higher stock removal or interrupted cuts. The full system comprises the ISO insert, a compatible external holder or boring bar, and the necessary shim/clamp set plus replacement screws to complete the assembly. If part geometry, surface finish or cycle time targets are critical, a short validation run with the insert in the intended holder will clarify the final parameter window for feeds and speeds. For precision finishing with Tungaloy quality, request the DCMT11T304 AT9530 via Metav Werkzeuge for availability and tailored application support — contact info@metav-werkzeuge.com or call +49 2822 7131930 for technical consultation Technical data Manufacturer item number: 6762156 SKU: 6762156-Tungaloy Manufacturer SKU: TUN6762156 Model series: ISO turning inserts Data Size: 11 mm Thickness: 3.97 mm Nose radius: 0.4 mm Clearance angle: 7° Principal angle: 55° Special features Material: coated cermet (grade AT9530) Plate form: rhombic Hole: cylindrical hole with one-sided countersink (40°–60°) Chipbreaker: single-sided Application: finishing and light machining of steel System components: compatible external holder or boring bar, shim/clamp set, replacement screws FAQ What materials is this insert best suited for? The DCMT11T304 AT9530 Tungaloy insert (SKU 6762156-Tungaloy) is intended primarily for steel finishing and light turning, where the coated cermet grade AT9530 delivers improved surface quality and controlled wear. Which toolholders will accept this insert? Compatibility follows ISO standards: the insert fits holders that match the DCMT form, size 11, thickness 3.97 mm, clearance angle 7° and the specified tolerance class; always verify form and attachment type before assembly. What nose radius and geometry should be expected for fine finishing? This insert features a 0.4 mm nose radius and a rhombic geometry that favour fine surface finishes and low cutting forces in finishing operations. Does the insert include a chipbreaker and what is its effect? Yes — the insert has a single-sided chipbreaker designed to promote consistent chip control and steady surface quality during finishing feeds. Is the insert suitable for heavy roughing or interrupted cuts? The DCMT11T304 AT9530 Tungaloy insert is optimised for finishing and light machining; for heavy roughing or highly interrupted cuts a more robust grade and different chipbreaker geometry are recommended. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
DCMT 11T304 DX120 Wendeplatten - Tungaloy
Take advantage of the combination of long tool life and very high cutting speeds through the PCD cutting material and an ISO‑standard geometry that ensures secure seating and predictable results; order the insert directly from Metav Werkzeuge or consult their team for application advice. DCMT 11T304 DX120 Tungaloy indexable insert for turning, PCD The DCMT 11T304 DX120 is an ISO‑form indexable insert designed for external and internal turning of aluminium, non‑ferrous and abrasive non‑metallic materials, offering a PCD cutting layer for extended tool life and consistent surface quality. ISO indexable geometry for reliable fit PCD DX120 for high cutting speeds Excellent tool life and wear resistance One-sided chipbreaker for aluminium turning Faster, more productive aluminium machining with PCD technology The PCD cutting material in the DX120 grade delivers high cutting speeds and long tool life when machining aluminium and abrasive non‑metallics. Polycrystalline diamond provides a hard, wear‑resistant cutting face that significantly reduces flank wear and maintains edge sharpness over extended cycles; this means fewer interruptions for tool changes and a more consistent surface finish. The insert’s built‑in one-sided chipbreaker improves chip control in light to medium depth cuts, reducing the risk of built‑up edge and helping to keep cycle times down while preserving dimensional accuracy. ISO geometry and stable seating for predictable results The rhombic insert conforms to the ISO designation and is specified as a 55° approach angle with a 0.4 mm nose radius, a 7° clearance angle and a thickness of 3.97 mm. These geometric parameters ensure secure clamping and repeatable positioning in standard external holders and boring bars. Compatibility with a holder depends on form, clearance angle, tolerance class, fastening method, size and thickness; correct matching minimises vibration and supports consistent cutting conditions. The insert also features a cylindrical hole with a single‑side countersink (40°–60°), enabling secure fixation and straightforward replacement during scheduled maintenance. Practical system advantages and handling for workshop use As part of an ISO turning system, the insert works together with a suitable external holder or boring bar, plus the appropriate shim/clamping set and replacement screws, to form a reliable cutting solution. The combination of a carbide substrate and a PCD cutting layer balances toughness with edge hardness: the substrate absorbs impact and supports the cutting layer, while the diamond face resists abrasive wear. For everyday shop practice, this translates into fewer tool changes, stable chip formation and an improved finish on aluminium components. When specifying inserts, select the chipbreaker and grade according to workpiece material, machining method and machine stability to achieve the best cost‑to‑performance ratio. For tailored recommendations on applications, inserts per batch requirements or stock status of the Tungaloy DCMT 11T304 DX120 indexable insert, contact Metav Werkzeuge at info@metav-werkzeuge.com or call +49 2822 7131930 for expert advice and fast processing. Technical data Article number: 6822160 Manufacturer SKU: TUN6822160 Internal SKU: 6822160-Tungaloy Manufacturer: Tungaloy Model series: ISO turning indexable inserts Facts Insert size: 11 mm Thickness: 3.97 mm Included angle: 55° Clearance angle: 7° Nose radius: 0.4 mm Special features Rhombic shape (DCMT) With hole: cylindrical hole + single-sided countersink (40°–60°) One-sided chipbreaker Grade: DX120 Cutting material: polycrystalline diamond (PCD) Substrate: carbide Application: external and internal turning System components: matching external holder or boring bar, shim/clamping set and replacement screws Compatibility determined by form, clearance, tolerance class, fastening, size and thickness FAQ What materials is this insert best suited for? The Tungaloy DCMT 11T304 DX120 insert is optimised for aluminium, non‑ferrous metals and abrasive non‑metallic materials owing to its PCD cutting face and DX120 grade. How does the DX120 grade affect productivity? The DX120 grade provides a wear‑resistant edge that enables longer continuous cutting runs and higher cutting speeds, so the DCMT 11T304 DX120 insert reduces tool change frequency and supports consistent part quality. Is the insert compatible with standard ISO holders? Yes; the insert follows ISO geometry, but compatibility depends on matching form, clearance angle, tolerance class, fastening method, size (11 mm) and thickness (3.97 mm) to the chosen holder. What chip control can be expected when turning aluminium? The single‑sided chipbreaker on this insert promotes controlled chip formation in aluminium turning, improving evacuation and reducing the risk of chip entanglement. Which system components are required to assemble the cutting system? A suitable external holder or boring bar, the correct shim or clamping set and the relevant replacement screws are required to form a complete and secure cutting assembly with this insert. Manufacturer/Responsible: Tungaloy‑NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand‑new product from the manufacturer.
DCMT 11T304 GH730 Wendeplatten - Tungaloy
The combination of GH730 wear-resistant carbide grade, a precise 0.4 mm corner radius and ISO conformity delivers stable edge life and consistent surface quality; order the DCMT11T304 inserts directly via Metav Werkzeuge or consult our advisers for application-specific guidance. DCMT11T304 GH730 turning insert by Tungaloy — rhombic, 7° clearance A DCMT11T304 GH730 ISO-standard turning insert designed for external and internal turning, offering robust edge stability and reliable chip control in production environments. ISO rhombic insert DCMT11T304 Carbide grade GH730 for wear resistance 0.4 mm corner radius for precise profiling 7° clearance with cylindrical hole and 40°–60° countersink Consistent wear life for stable production results The combination of the GH730 carbide grade and a dedicated cutting geometry provides notable wear resistance while retaining sufficient toughness for interrupted cuts. As an indexable insert, this component concentrates the wear on a replaceable cutting edge, reducing total toolholder costs and simplifying inventory management. The result is a predictable tool life that supports process planning, fewer unexpected stoppages and a more consistent surface finish on workpieces. Accurate geometry and secure clamping for repeatable parts The rhombic plate form with a 55° included angle and 7° clearance angle ensures reliable cutting engagement and reduced radial forces during turning. The 0.4 mm corner radius enables precise profiling and controlled cutter contact, which benefits dimensional repeatability and surface quality. The insert’s cylindrical hole with a single-sided countersink (40°–60°) facilitates secure, repeatable clamping in compatible holders and helps maintain consistent cutting geometry across insert changes. Easy integration into ISO tool systems and flexible chip control Being an ISO‑standard indexable plate, the insert fits into common external holders or boring bars if the form, relief angle, tolerance class, mounting and thickness match. The one-sided chipbreaker geometry is selected to suit material, machining strategy and machine stability, enabling efficient chip formation and evacuation. This modular approach supports quick replacements, reduces setup time and yields a cost‑effective path to higher throughput in turning operations. For demanding turning operations where edge stability and predictable tool life matter, request genuine Tungaloy DCMT11T304 GH730 inserts via Metav Werkzeuge or contact our technical team at info@metav-werkzeuge.com / +49 2822 7131930 for tailored recommendations. Technical Data Article number: 6820988 SKU: 6820988-Tungaloy Manufacturer SKU: TUN6820988 Model series: ISO-Drehwendeschneidplatten Material: Hartmetall Grade: GH730 Facts Plate designation: DCMT11T304 Plate size: 11 mm Plate thickness: 3.97 mm Corner radius: 0.4 mm Clearance angle: 7° Included angle: 55° Hole: with hole (cylindrical + single-sided countersink 40°–60°) Special features Rhombic plate form One-sided chipbreaker ISO-standard indexable insert for turning Intended for external and internal turning Compatibility depends on holder form, relief, tolerance class, mounting and thickness FAQ What applications is this insert intended for? The DCMT11T304 GH730 insert is intended for external and internal turning operations and is supplied as an ISO-standard indexable plate for general turning tasks. Which cartridge grade is used and why is it relevant? This insert uses the GH730 carbide grade from Tungaloy; the grade balances wear resistance and toughness to deliver stable cutting performance and predictable tool life. How does the insert fasten to a holder? The insert features a cylindrical hole with a single-sided countersink (40°–60°) for secure clamping; compatibility is determined by holder form, relief angle, tolerance class, mounting and thickness. What cutting geometry characteristics improve surface finish? The rhombic shape with a 55° included angle, a 7° clearance and a 0.4 mm corner radius contribute to controlled cutter engagement and repeatable surface quality. Is this insert suitable for interrupted cuts and varying stability conditions? The GH730 grade and the selected cutting geometry give a compromise of toughness and wear resistance designed to withstand varying conditions, including some interrupted cutting; selection of the appropriate chipbreaker further adapts performance. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
DCMT 11T304 GH730 Wendeplatten - Tungaloy
Take advantage of the combination of ISO compatibility, GH730 wear resistance and reliable clamping for steady turning performance; order directly via Metav Werkzeuge or consult our specialists for application advice. DCMT 11T304 GH730 — Tungaloy indexable turning insert, 0.4 mm radius, 7° clearance The DCMT11T304 GH730 indexable insert designed for machining operations in standard ISO turning systems, offering a balance of wear resistance and edge stability for external and internal turning ISO‑standard rhombic insert, 11 mm GH730 grade for wear resistance 0.4 mm corner radius for versatile finishes Cylindrical hole with single-sided countersink Consistent compatibility for industrial turning The DCMT11T304 GH730 insert is produced to ISO standard dimensions so that compatibility with holders is predictable: form, clearance angle, tolerance class, fastening and thickness determine the correct match. Using an ISO‑compliant component reduces setup uncertainty and shortens changeover times because available ISO holders and boring bars accept the insert without bespoke adapters. For operations that require quick tool changes and repeatable positioning, this standardisation supports higher uptime and a measurable productivity gain. Durability and reliable edge life from GH730 carbide The insert is manufactured from a carbide substrate combined with the GH730 grade, which is engineered to balance wear resistance and toughness. This composition helps maintain cutting‑edge integrity under continuous contact and at elevated temperatures typical of turning. In practical terms, the grade extends time between indexings and replacements, lowering tooling-related downtime. For process planners, the result is a more predictable tool lifetime and reduced intervention frequency during batch production. Geometry engineered for surface quality and chip control A rhombic plate form with a 0.4 mm corner radius and 7° clearance produces a combination of accessibility and surface finish suited to a range of turning tasks. The modest corner radius permits finer profile work and improved edge strength for light to medium cuts; larger radii are typically chosen for heavy roughing. The insert’s single-sided chipbreaker steers chips away from the cut and stabilises cutting forces, while the cylindrical hole with single-sided countersink (40°–60°) ensures secure clamping and consistent seat geometry. These features together support improved surface integrity and fewer interruptions for chip clearing. System integration and operational advantages This item is intended to form part of a complete turning system: an ISO indexable insert, the corresponding outer holder or boring bar, a seat/clamping kit and replacement screws. The 3.97 mm plate thickness contributes to stiffness in the tool assembly, helping to maintain radial and axial rigidity under load. For workshop managers, that translates into reduced vibration sensitivity and steadier dimensional results. Selecting the appropriate chipbreaker and insert grade for the workpiece and machining conditions will further enhance process reliability and can deliver lower overall machining costs through longer tool life and fewer reworks. For machining applications that demand consistent edge life and ISO interchangeability, contact Metav Werkzeuge for Tungaloy GH730 indexable inserts and tailored advice via info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: 6820987 SKU: 6820987-Tungaloy Manufacturer SKU: TUN6820987 Product name: DCMT11T304 GH730 Tungaloy indexable insert Material: carbide Core specifications Size: 11 mm Thickness: 3.97 mm Corner radius: 0.4 mm Clearance angle: 7° Cutting angle: 55° Hole style: cylindrical hole + single-sided countersink (40°–60°) Design and special features Rhombic insert shape Single-sided chipbreaker Cylindrical hole with single-sided countersink GH730 Tungaloy grade ISO conformity for holder compatibility Intended for turning applications FAQ What clamping system is required for this insert? The DCMT11T304 GH730 indexable insert requires an ISO‑compatible rhombic pocket in the outer holder or boring bar; clamping is effected via the cylindrical hole with the single‑sided countersink. Which applications suit the GH730 grade best? GH730 is designed to balance wear resistance and toughness, making it appropriate for general turning tasks where consistent edge life and resistance to abrasive wear are priorities. Can this insert be used for internal and external turning? Yes, the insert geometry and standard ISO form allow use in both external and internal turning when paired with the correct outer holder or boring bar. How does the 0.4 mm corner radius affect machining? A 0.4 mm corner radius provides a compromise between fine profile capability and edge strength, supporting smoother surface finishes on finishing passes while maintaining robustness for moderate cuts. Is the insert suitable for high‑speed machining? The carbide substrate and GH730 grade offer good thermal and mechanical resistance; suitability for high‑speed conditions depends on machine, cooling and specific workpiece material parameters. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
DCMT 11T304 GH730 Wendeplatten - Tungaloy
Take advantage of the combination of GH730 wear resistance, precise 0.4 mm corner radius, and ISO compatibility for steady production results; the insert's secure hole and rhombic form ensure reliable seating in standard holders. Order the DCMT11T304 GH730 Tungaloy indexable insert directly via Metav Werkzeuge or ask our consultants if needed. DCMT11T304 GH730 Tungaloy indexable insert, cemented carbide, 0.4 mm radius The DCMT11T304 GH730 Tungaloy indexable insert is designed for external and internal turning in ISO-compatible holders, providing stable cutting performance for a variety of turning tasks. ISO form DCMT, 7° clearance angle GH730 carbide grade for wear resistance 0.4 mm corner radius for fine surface finishes Rhombic shape with cylindrical hole and countersink Consistent edge stability for reliable turning The combination of the GH730 grade and cemented carbide substrate gives this insert a balance of wear resistance and edge stability that supports longer tool life and consistent finishes. In practice, the enhanced edge retention reduces frequency of tool changes and helps maintain dimensional accuracy over extended production runs. This benefit is particularly relevant where repeatability and surface integrity are priorities, as the robust cutting edge resists chipping under typical turning loads. Precision geometry for secure clamping and repeatability Engineered to ISO form, the insert's 55° included angle and 7° clearance work with the rhombic profile to ensure predictable seating and force distribution in a compatible holder. The 3.97 mm thickness and 11 mm inscribed circle contribute to stable clamping, while the central hole with cylindrical bore and single-sided countersink (40°–60°) secures the insert against rotation. These geometric features translate into reduced vibration, improved tool life and steadier workpiece tolerances when fitted into a correctly specified toolholder. Controlled chip formation and adaptable application Equipped with a one-sided chipbreaker and a 0.4 mm corner radius, the insert helps produce manageable chips and promotes effective evacuation, lowering heat concentration at the cutting edge. This design supports both roughing and finishing passes when the grade and geometry are matched to workpiece stability and material. For general turning tasks, selecting the appropriate chipbreaker and cutting conditions enhances process reliability and can improve cycle times without compromising surface quality. Contact Metav Werkzeuge for application advice on Tungaloy GH730 inserts — our specialists can assist with holder compatibility, cutting data and inventory availability; email info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: 6820989 Manufacturer SKU: TUN6820989 Model series: ISO indexable turning inserts Material: cemented carbide Numbers / Core technical data Corner radius: 0.4 mm Thickness: 3.97 mm Inscribed circle: 11 mm Clearance angle: 7° Included angle: 55° Design / Special features ISO designation: DCMT11T304 Grade: GH730 (Tungaloy) Shape: rhombic Hole: with hole — cylindrical hole + single-sided countersink (40°–60°) Chipbreaker: one-sided Application: turning FAQ What holder form is required for this insert? The insert uses the ISO DCMT11T304 form and fits standard rhombic turning holders that accept a 55° insert with a central hole and matching clamp geometry. Which machining tasks is the GH730 grade suited to? The GH730 Tungaloy grade is optimised for turning, offering a combination of wear resistance and toughness that supports steady performance in many routine turning operations. How does the chipbreaker affect machining? The one-sided chipbreaker promotes controlled chip formation and better evacuation, which helps reduce heat at the cutting edge and supports improved surface quality. What finish can be expected with a 0.4 mm corner radius? A 0.4 mm corner radius is suitable for fine finishing passes, balancing edge strength with the ability to achieve modest surface roughness values when cutting parameters are set accordingly. How can the insert be identified for reordering? Reorder using the ISO designation DCMT11T304, grade GH730, or manufacturer article number 6820989 to ensure the correct insert and geometry are supplied. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
DCMT 11T304 GT9530 Wendeplatten - Tungaloy
Take advantage of the combination of coated cermet durability, precise 55° rhombic geometry and a compact 0.4 mm corner radius to secure consistent finishing results in turning operations; order the insert directly via Metav Werkzeuge or consult our specialists for application support. DCMT11T304 GT9530 Tungaloy turning insert – 55° rhombic, coated cermet for finishing The DCMT11T304 GT9530 is a 55° rhombic indexable insert designed for external and internal turning where a fine surface finish and extended tool life under stable conditions are required Coated cermet GT9530 grade 55° rhombic insert geometry 0.4 mm corner radius Cylindrical hole with 40°–60° countersink Delivering consistent finishing and longer tool life The GT9530 coated cermet composition provides a balance between wear resistance and workpiece surface quality that suits finishing to light universal turning in Stahl. The coating improves adhesion and reduces flank wear, which results in longer cutting life and fewer insert changes. For production environments where cycle stability and predictable tool life matter, this grade supports a reliable process with reduced downtime. Geometry that matches precision and stability requirements The rhombic 55° form, paired with a 0.4 mm corner radius and a clearance angle of 7°, gives a favourable compromise between access to detail and edge strength. The insert thickness of 3.97 mm contributes to rigidity in the tool assembly. The insert is supplied with a hole and a cylindrical hole plus one-sided countersink (40°–60°) to ensure secure clamping in compatible holders. Correct holder selection—matching form, relief angle, tolerance class, fastening, size and thickness—ensures the expected cutting behaviour and repeatability in production. Chip control and application guidance for turning operations A one-sided chipbreaker is integrated to assist in stable chip formation during external and internal turning. Under steady setup conditions this chipformer helps maintain surface integrity and reduces the risk of built-up edge. Select the GT9530 grade and the chipbreaker geometry to suit material and stability: the grade is optimised for Stahl machining where a fine finish and extended life are priorities. The insert is part of the ISO turning insert family and typically forms a system with an appropriate external holder or boring bar, a backing pad/clamp set and replacement screws. For precision finishing with the GT9530 grade and the DCMT11T304 geometry, contact Metav Werkzeuge for tailored technical advice and availability via info@metav-werkzeuge.com or call +49 2822 7131930. Technical data Manufacturer article number: 6998342 Merchant SKU: 6998342-Tungaloy Manufacturer SKU: TUN6998342 Model series: ISO turning indexable inserts Insert designation: DCMT11T304 Grade: GT9530 Material: cemented carbide Numbers / core technical data Corner radius: 0.4 mm Insert size: 11 Insert thickness: 3.97 mm Relief (clearance) angle: 7° Main angle: 55° SKU / article reference: 6998342 Designs / special features Rhombic insert shape Coated cermet grade GT9530 One-sided chipbreaker With hole; cylindrical hole + one-sided countersink (40°–60°) Intended application: turning (external and internal) Compatibility determined by form, free angle, tolerance class, fastening, size and thickness FAQ What materials is the GT9530 grade suited for? The GT9530 coated cermet grade is designed principally for machining Stahl where a fine surface finish and improved tool life are required; it performs best under stable cutting conditions. Which operations is this insert intended for? The rhombic DCMT11T304 insert is intended for external and internal turning applications, particularly finishing and light universal turning tasks. How does the 0.4 mm corner radius affect performance? A 0.4 mm corner radius balances edge strength with the ability to produce a fine surface finish; it reduces the tendency for edge chipping while allowing detailed profile machining. What does the hole and countersink configuration mean for clamping? The cylindrical hole with one-sided countersink (40°–60°) ensures secure axial and radial clamping when used with compatible holders and clamping sets, supporting repeatable tool positioning. Is this insert compatible with standard ISO holders? Yes, the insert follows ISO designation standards; compatibility depends on matching the holder’s form, relief angle, tolerance class, fastening method, size and thickness to the insert specification. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
DCMT 11T304 GT9530 Wendeplatten - Tungaloy
Take advantage of a wear‑resistant cermet grade and precise ISO geometry for consistent finishing results and prolonged tool life; the combination of GT9530 performance and standardised form ensures predictable integration into existing tool systems. Order the insert directly via Metav Werkzeuge or consult our technical team for application-specific advice. DCMT11T304 GT9530 — Tungaloy turning insert (ISO, finishing) The DCMT11T304 GT9530 is a wear‑resistant cermet indexable insert designed for finishing and light universal turning in stable machining conditions Cermet grade GT9530 for extended tool life Optimised for finishing and light universal turning ISO DCMT 11T304, 55° rhombic geometry Cylindrical hole with 40°–60° countersink Reliable surface quality through a wear‑resistant grade The GT9530 formulation is a cermet‑based cutting grade engineered to deliver a consistently high surface finish when machining steels. As a finishing‑oriented option, the grade combines abrasion resistance with thermal stability to reduce flank wear during long runs under stable cutting conditions. For shops seeking predictable component quality, the result is fewer reworks and more parts meeting tolerance on first pass thanks to the insert’s ability to sustain a sharp cutting edge for longer. Predictable cutting behaviour with ISO geometry The rhombic 55° platform and standardised hole and clamping features provide straightforward compatibility with ISO toolholders. The DCMT11T304 geometry offers a compromise between approach angle and strength, allowing accurate profile control while maintaining sufficient edge support. Because compatibility is governed by form, relief angle, tolerance class, clamping method, size and thickness, adopting an ISO insert simplifies tooling logistics and reduces set‑up time across multiple lathes. Geometry and micro‑features that support repeatability Key geometric parameters such as the 0.4 mm corner radius, 7° relief angle and 3.97 mm thickness contribute directly to edge stability and consistent chip formation. A small corner radius favours high‑quality finishes on turned surfaces, while the specified relief prevents rubbing at the flank. These measurable features help machinists select cutting data with confidence and predict the interaction between insert and workpiece for repeatable production results. Chip control and secure mounting for efficient turning The insert features a one‑sided chipbreaker and a cylindrical hole with single‑sided countersink (40°–60°) to support reliable clamping and effective chip evacuation. Combined with the carbide substrate, the chip geometry reduces the risk of built‑up edge in finishing passes and aids coolant penetration when used. This structure makes the component suitable for both external and internal turning operations where surface integrity and process stability are priorities. System integration and handling advantages As an ISO indexable insert, the part integrates into established tool systems with predictable mechanical interfaces. The standardised form factor eases stock management and interchangeability between holders and boring bars, while the grade’s focus on finishing helps to extend intervals between insert changes. For production environments prioritising uptime, the combination of grade and geometry supports longer continuous runs and simplified tooling choices. For reliable finishing performance, request the Tungaloy DCMT11T304 GT9530 insert from Metav Werkzeuge or contact our technical advisers at info@metav-werkzeuge.com or by phone on +49 2822 7131930 to discuss suitable holders and cutting parameters. Technical data Article number: 6998332 SKU: 6998332-Tungaloy Manufacturer SKU: TUN6998332 Brand: Tungaloy Core specifications ISO designation: DCMT11T304 Size: 11 Thickness: 3.97 mm Insert angle: 55° Clearance angle: 7° Corner radius: 0.4 mm Design & features Material: carbide Grade/coating: GT9530 (cermet) Plate form: rhombic Hole: with hole – cylindrical hole + single‑sided countersink (40°–60°) Chipbreaker: one‑sided Application: turning Compatible system: ISO indexable turning inserts FAQ Which materials is this insert best suited for? The DCMT11T304 GT9530 insert from Tungaloy is formulated as a wear‑resistant cermet grade primarily aimed at steels, providing good surface finish and extended life in finishing and light universal turning operations. How does the GT9530 grade improve tool life? GT9530 combines abrasion resistance and thermal stability so the cutting edge maintains sharpness longer in stable conditions, allowing the Tungaloy insert to deliver more consistent parts over extended runs. What holder compatibility should be checked before use? Compatibility depends on the holder’s form, relief, tolerance class, clamping type, size and thickness; the DCMT11T304 designation conforms to ISO standards, simplifying matching with suitable external holders and boring bars. What are the important geometric features to consider when setting cutting data? Focus on the 55° geometry, 0.4 mm corner radius and 7° relief angle along with the 3.97 mm thickness; these parameters influence edge strength, surface finish and recommended feeds and speeds for finishing cuts. Can this insert be used for internal turning as well as external turning? Yes, the indexable concept and the insert’s form allow both external and internal turning; select an appropriate holder and ensure secure clamping using the cylindrical hole with single‑sided countersink for internal applications. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand‑new product from the manufacturer.
DCMT 11T304 GT9530 Wendeplatten - Tungaloy
Take advantage of the combination of durable GT9530 coating, ISO‑standard geometry and precise seating for a reliable finishing operation; order or request application advice via Metav Werkzeuge for fast integration into existing turning processes. DCMT 11T304 GT9530 — Rhombic ISO turning insert, coated cermet, Tungaloy DCMT 11T304 GT9530 is an ISO‑standard indexable insert designed for turning and finishing applications in steel, offering a balance of surface quality and extended tool life. Cermet coating GT9530 for longer life ISO‑standard rhombic DCMT 11T304 geometry 0.4 mm corner radius for fine surface finish Cylindrical hole with single‑side countersink High‑quality finishing with a wear‑resistant grade The GT9530 coated cermet grade is engineered for finishing to light universal turning of steel, delivering a notable improvement in surface integrity and edge stability under steady cutting conditions. The small 0.4 mm corner radius and the rhombic seating result in a refined machined face and reduced need for secondary operations. For production environments where consistent dimensional accuracy and repeatable surface finish matter, this grade reduces downtime associated with frequent insert changes and stabilises process output. Reliable fit and straightforward system integration Manufactured to ISO specifications, the insert’s DCMT geometry and nominal size simplify holder selection: compatibility is determined by form, clearance angle, tolerance class, fastening method, overall size and thickness. The 3.97 mm thickness and the cylindrical hole with a single‑side countersink (40°–60°) ensure secure clamping and positive location in matching external holders or boring bars. A complete cutting system comprises the indexable insert, an appropriate external holder or boring bar, a locating pad/clamping set and replacement screws, allowing efficient tool replacement and consistent clamping integrity. Process benefits and application guidance A single‑sided chipbreaker on this insert supports stable chip control in finishing cuts, reducing the risk of re‑cutting and improving surface consistency. The cermet substrate provides a hard, wear‑resistant edge that maintains sharpness for superior finish, while the coating enhances resistance to abrasive wear—resulting in longer tool life under recommended conditions. For optimal results select the chipbreaker and grade according to workpiece stability, feed and depth of cut; the insert excels where a high‑quality surface and predictable performance are priorities. For tailored application advice or to secure stock of Tungaloy GT9530 inserts, contact Metav Werkzeuge for prompt assistance via info@metav-werkzeuge.com or call +49 2822 7131930 Technical Data Article number: 6723191 Manufacturer SKU: TUN6723191 Brand: Tungaloy Model series: ISO turning indexable inserts Designation: DCMT11T304 GT9530 Facts Size: 11 Thickness: 3.97 mm Corner radius: 0.4 mm Clearance angle: 7° Diamond angle: 55° Special features Coated cermet grade GT9530 Rhombic insert shape (DCMT) Cylindrical hole with single‑side countersink (40°–60°) Single‑sided chipbreaker Intended application: turning (finishing to light universal) Material: carbide FAQ What materials is this insert intended for? The GT9530 coated cermet insert is intended primarily for turning steel, particularly in finishing and light universal operations where a good surface finish and longer tool life are required. What is the full designation and how is it identified? The insert is designated DCMT11T304 GT9530 (Article number 6723191, SKU TUN6723191) and is identifiable by its rhombic shape, 11 size, 0.4 mm corner radius and the GT9530 coated cermet grade. Which holder characteristics are required for compatibility? Compatibility depends on matching the insert’s form, 7° clearance angle, tolerance class, fastening style, size and 3.97 mm thickness; ISO‑compliant turning holders and boring bars with corresponding clamping arrangements are suitable. How does the GT9530 grade affect machining results? GT9530 provides a wear‑resistant cutting edge with improved surface integrity and prolonged edge life under stable cutting conditions, reducing the frequency of insert changes and improving process consistency. Is this insert suitable for heavy roughing operations? This grade and geometry are optimised for finishing to light universal turning rather than heavy roughing; for roughing applications, a more robust geometry and grade should be selected. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand‑new product from the manufacturer.
DCMT 11T304 GT9530 Wendeplatten - Tungaloy
Take advantage of a robust combination of GT9530 coated cermet performance and precise 55° geometry to achieve consistent finishing and extended tool life in turning operations; order directly via Metav Werkzeuge or consult the technical team for application-specific advice. DCMT 11T304 GT9530 turning insert — Tungaloy, coated cermet, 55° DCMT 11T304 GT9530 is an ISO rhombic turning insert designed for finishing to light universal turning of steel where a fine surface and extended tool life are required Coated cermet GT9530 for improved life 55° rhombic form DCMT for versatile turning 0.4 mm corner radius for fine finishes Cylindrical hole with 40°–60° countersink Achieve consistent finishes with a wear-resistant cermet grade The GT9530 grade is a coated cermet tuned for finish to light universal turning of steel, providing a balance between surface quality and tool life when machining under stable conditions. Its composition promotes stable chip formation, which reduces vibration and helps maintain consistent cutting conditions over longer tool intervals. For production environments prioritising surface integrity on hardened process chains, this grade offers measurable improvements in repeatability and reduced rework. Geometry engineered for precision and secure mounting The rhombic DCMT geometry with an included angle of 55° and a 0.4 mm corner radius delivers controlled cutting engagement and excellent access to shoulder and profile features. The insert is supplied with a cylindrical hole and a one-sided countersink (40°–60°) to match common ISO clamping systems; the plate thickness of 3.97 mm and a clearance angle of 7° ensure stable seating and predictable chip flow. The result is precise tool positioning, straightforward indexability, and compatibility with standard external holders and boring bars for seamless integration into existing tool assemblies. Improve productivity through reliable chip control and system compatibility The single-sided chipbreaker design simplifies selection for finishing tasks, supporting consistent chips and reduced interruption during turning cycles. When combined with an appropriate carbide-tipped holder and standard clamping kit, the insert contributes to reduced changeover time and fewer stoppages. The cemented carbide substrate provides the necessary edge support for the coated cermet layer, enabling longer tool life during steady-state operations and lowering total process cost per component in batch production. Application guidance for workshops and production lines Intended primarily for external and internal turning of steel, the insert suits job shops and industrial production where surface finish and component consistency are critical. Select this grade and the one-sided chipbreaker for operations with stable set-up rigidity and controlled feeds to exploit the coating’s strengths. For varied materials or heavy interrupted cuts, consider alternative geometries or grades matched to the specific alloy and cutting conditions; technical consultation is available for process matching and holder recommendations. Order GT9530 grade DCMT inserts from Metav Werkzeuge for improved finishing and extended tool life — contact Metav Werkzeuge for expert advice at info@metav-werkzeuge.com or +49 2822 7131930 Technical data Article number: 6998329 Manufacturer SKU: TUN6998329 Brand: Tungaloy Series: ISO turning indexable inserts Facts Size: 11 mm Thickness: 3.97 mm Included angle: 55° Clearance angle: 7° Corner radius: 0.4 mm Special features Coated cermet grade GT9530 Single-sided chipbreaker Cylindrical hole with 40°–60° countersink Rhombic form DCMT (ISO designation 11T304) Suitable for external and internal turning of steel FAQ What cutting tasks is this insert optimised for? The DCMT 11T304 GT9530 insert from Tungaloy is optimised for finishing to light universal turning of steel, delivering improved surface quality and extended tool life under stable cutting conditions. Can the insert be used for internal as well as external turning? Yes, the rhombic geometry and compact size make the insert suitable for both external and internal turning applications using compatible boring bars or external holders. Which chipbreaker and grade should be chosen for steel finishing? For steel finishing, the GT9530 coated cermet grade combined with the single-sided chipbreaker provides stable chip control and a fine surface finish in steady setups. How is the insert secured in the holder? The insert features a cylindrical mounting hole with a one-sided countersink (40°–60°) and standard ISO clamping compatibility for secure seating with matching screws and shims. What is the manufacturer SKU for ordering? The manufacturer SKU for this Tungaloy turning insert is TUN6998329 (article number 6998329), listed as DCMT 11T304 GT9530. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
DCMT 11T304 GT9530 Wendeplatten - Tungaloy
Benefit from a combination of longer tool life, consistent fine finishing and broad ISO compatibility that keeps production steady and predictable; order the DCMT11T304 GT9530 indexable insert directly via Metav Werkzeuge or ask our consultants if needed. DCMT11T304 GT9530 — ISO turning insert for turning, Tungaloy The DCMT11T304 GT9530 is an ISO‑standard rhombic indexable insert designed for external and internal turning, offering a wear‑resistant cermet grade tailored to finishing operations under stable conditions. ISO rhombic insert with 55° cutting angle Coated cermet grade GT9530 for fine finishing 0.4 mm corner radius, single‑sided chipbreaker Cylindrical hole with countersink, 3.97 mm thick Consistent finishes and longer tool life for finishing passes The coated cermet GT9530 brings a balance between hardness and toughness that favours excellent surface quality on steels during light finishing and universal turning. Cermet combines ceramic phases with a metallic binder to reduce flank wear and maintain edge geometry, which translates into fewer tool changes and more reliable batch quality. This hardness‑focused composition is particularly effective where a superior finish and extended tool life are higher priorities than aggressive metal removal. Secure clamping and ISO compatibility to simplify tool management Designed to the ISO form DCMT11T304, the rhombic insert matches ISO‑standard holders by shape, relief angle and tolerance class, ensuring predictable seating and repeatable tool offsets. Key dimensions such as the 55° included angle, 7° clearance, 0.4 mm corner radius and 3.97 mm thickness support secure clamping and stable cutting conditions. The insert’s cylindrical hole with a one‑sided countersink (40°–60°) assists reliable fastening and accurate orientation, reducing setup variability and supporting uninterrupted production runs. Practical application guidance and operational advantages This grade is intended for turning of steels where a high‑quality surface and longer cutting life are required under steady conditions; select the appropriate chipbreaker and grade for the specific workpiece material and machining stability. The single‑sided chipbreaker favours controlled chip flow during finishing passes, lowering the risk of surface damage. For detailed feed and speed recommendations or compatibility checks with a specific holder system, Metav Werkzeuge can provide technical assistance — email info@metav-werkzeuge.com or call +49 2822 7131930 for tailored data and application advice. For reliable finishing performance with Tungaloy quality, contact Metav Werkzeuge for ordering and expert guidance on application and holder compatibility Technical Data Manufacturer article number: 6998338 SKU: 6998338-Tungaloy Manufacturer SKU: TUN6998338 Model series: ISO‑Drehwendeschneidplatten Application: Turning Grade: GT9530 Core specifications Shape/ISO designation: DCMT11T304 Included angle: 55° Clearance angle: 7° Corner radius: 0.4 mm Thickness: 3.97 mm Size: 11 Features & material compatibility Material: carbide Coating/type: coated cermet (GT9530) Chipbreaker: single‑sided Hole style: cylindrical hole + one‑sided countersink (40°–60°) Plate form: rhombic Typical use: external and internal turning on steel FAQ What materials is this insert suitable for? The DCMT11T304 GT9530 insert is a coated cermet grade intended primarily for turning steel, offering a fine finishing performance under stable cutting conditions. Can this insert be used for internal turning as well as external turning? Yes, the ISO‑rhombic geometry and the specified dimensions make the insert suitable for both external and internal turning operations when paired with the correct holder. How does the GT9530 grade improve surface finish? GT9530’s cermet composition provides a harder cutting edge with good wear resistance, which helps maintain edge geometry and produces smoother surfaces during finishing passes. What are the critical dimensions to check for holder compatibility? Check the ISO form (DCMT11T304), 55° included angle, 7° clearance, thickness 3.97 mm and the hole/countersink style to ensure correct seating and clamping. Is the chip control suitable for finishing passes? Yes, the single‑sided chipbreaker is optimised for controlled chip flow during finishing, reducing the risk of surface marks and improving consistency. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
Fragen zu diesen Produkten??
Mit mehr als 30 Jahren Erfahrung beraten wir Sie gerne persönlich.
Tel.: +49 2822 7131930
Mail: info@metav-werkzeuge.com