DCMT 11T312 AH6235 Wendeplatten - Tungaloy
Take advantage of the PVD-coated AH6235 grade and the robust 1.2 mm corner radius for secure, repeatable machining of stainless steel and interrupted cuts; the rhombic geometry with a 55° cutting angle ensures low vibration and consistent surface finish. Order the insert directly via Metav Werkzeuge or consult our specialists for holder compatibility and process optimisation. DCMT 11T312 AH6235 turning insert – ISO DCMT indexable insert by Tungaloy A DCMT11T312 AH6235 indexable turning insert designed for external and internal turning, optimised for stainless steel and interrupted cutting conditions PVD-coated carbide AH6235 for stainless steel Rhombic DCMT shape with 55° cutting angle 1.2 mm corner radius for enhanced edge strength Cylindrical hole with 40°–60° countersink Reliable cuts in stainless steel with a tougher grade The PVD-coated carbide AH6235 is formulated as a tougher grade to cope with the demands of machining stainless steel and interrupted cutting. The combination of the PVD coating and a resilient substrate reduces the risk of chipping under unstable cutting conditions, delivering longer effective tool life and fewer unplanned tool changes. For production environments where occasional interruptions or variable feeds are common, this approach reduces scrap and increases process uptime. Stable geometry for consistent surface quality and clamping The rhombic DCMT geometry with a 55° main cutting angle and a 1.2 mm corner radius provides a balance between edge strength and surface finish. The plate thickness of 3.97 mm and the 7° relief angle contribute to rigidity in the cutting zone, while the cylindrical hole with 40°–60° countersink ensures reliable clamping and repeatable seating in compatible holders. Compatibility depends on form, relief angle, tolerance class, fastening method, size and thickness, so select the matching holder and fixings to secure stable, reproducible results. System approach for efficient chip control and uptime As an ISO-standard turning insert, this plate integrates into a system comprising the indexable insert, a suitable external holder or boring bar, backing/clamping set and replacement screws. The one-sided chipbreaker is tuned for moderate chip control in common turning operations; when paired with the tougher AH6235 grade it reduces edge deterioration in stop-start cuts and improves chip evacuation. The result is more reliable cycle times and predictable maintenance intervals, supporting higher productivity in component machining. For tailored advice on holder compatibility or to request the DCMT11T312 AH6235 insert for a specific stainless steel application, contact Metav Werkzeuge and benefit from expert selection and fast availability Technical data Article number: 6903468-Tungaloy Manufacturer article number: 6903468 Manufacturer SKU: TUN6903468 Model series: ISO-Drehwendeschneidplatten Material: Hartmetall Facts Corner radius: 1.2 mm Cutting angle: 55° Relief (free) angle: 7° Thickness: 3.97 mm Plate size: 11 mm Special features PVD-coated carbide grade AH6235 Rhombic plate form (DCMT) One-sided chipbreaker Cylindrical hole + one-sided countersink (40°–60°) Compatible with ISO-standard turning holders Optimised for stainless steel and interrupted cuts FAQ Is this insert suitable for interrupted cuts in stainless steel? This insert, the DCMT11T312 AH6235 Tungaloy indexable insert (SKU 6903468-Tungaloy), is specifically graded for interrupted cuts and offers enhanced resistance to chipping when machining stainless steel. What holder features are required for correct mounting? Correct mounting requires a holder matching the DCMT form, the plate thickness of 3.97 mm, the 7° relief angle and the fixing method; ensure the holder accepts a cylindrical hole with countersink to guarantee secure seating. How does the AH6235 grade affect tool life? The AH6235 PVD-coated grade provides a tougher substrate with protective coating, which increases edge security under variable cutting conditions and typically extends effective tool life in stainless steel applications. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
DCMT 11T312 AH6235 Wendeplatten - Tungaloy
Take advantage of a robust, PVD-coated carbide grade and a 1.2 mm corner radius for reliable performance in demanding turning operations; the combination of interrupted-cut capability and ISO compatibility supports stable production and reduced rework. Order genuine Tungaloy inserts directly via Metav Werkzeuge or consult the team for application guidance. DCMT 11T312 AH6235 – ISO turning insert for external and internal turning, Tungaloy A precise DCMT11T312 AH6235 ISO turning insert engineered for demanding rostfreier Stahl work and interrupted cuts, supplied as a rhombic indexable insert for standard ISO holders. PVD-coated carbide grade AH6235 Optimised for rostfreier Stahl and interrupted cuts Rhombic insert with 1.2 mm corner radius Durable cutting performance for high-risk interruptions The PVD-coated carbide grade AH6235 provides a tougher substrate and a coating that improves edge security under cyclic loading and interrupted cuts. This combination results in stable chip formation and reduced flank wear during heavy engagement, which translates into fewer regrinds and longer tool life. The tougher grade is particularly suitable for applications with elevated breakout risk, improving process reliability in series production. Consistent fit within ISO tooling systems Compatibility is determined by form, relief angle, tolerance class, fastening method, size and thickness; the insert follows the ISO designation DCMT11T312, ensuring interchangeability with matching holders and boring bars. The rhombic shape and the specified dimensions allow straightforward replacement and re-indexing, reducing spindle downtime. A clear system setup — insert, holder, shim/clamping kit and replacement screws — supports consistent assembly and repeatable results. Geometry that balances edge strength and precision The 1.2 mm corner radius and a 7° relief angle are chosen to balance cutting-edge toughness and dimensional control. The moderate corner radius increases resistance to chipping while maintaining acceptable roughness for finishing passes, so fewer follow-up operations are required. The insert thickness of 3.97 mm and the rhombic form contribute to mechanical stability during heavy cuts and interrupted sequences. Practical features for secure clamping and process control A cylindrical hole with single-sided countersink (40°–60°) enables secure fastening and precise location in standard clamping systems. The one-sided chipbreaker design helps direct chips away from the cutting zone, improving surface quality and evacuation, especially with rostfreier Stahl. By selecting the right chipbreaker and grade for the material and machining conditions, users can increase productivity and reduce scrap rates. Contact Metav Werkzeuge for tailored advice on Tungaloy turning inserts and to ensure the correct insert-grade selection for specific rostfreier Stahl applications — eMail: info@metav-werkzeuge.com | Phone: +49 2822 7131930 Technical Data Article number: 6903470 SKU: 6903470-Tungaloy Manufacturer SKU: TUN6903470 Model series: ISO turning indexable inserts Facts ISO designation: DCMT11T312 Angle: 55° Corner radius: 1.2 mm Relief angle: 7° Thickness: 3.97 mm Insert size: 11 Special features Grade: AH6235 Cutting material: Carbide, PVD-coated Shape: rhombic Hole: with hole Hole style: cylindrical hole + single-sided countersink (40°–60°) Chipbreaker: one-sided Application: Turning (external and internal) FAQ What materials is this insert best suited for? The DCMT11T312 AH6235 Tungaloy insert is formulated for machining rostfreier Stahl and other demanding materials where interrupted cuts and breakout risk occur, thanks to the tougher PVD-coated grade. How does the 1.2 mm corner radius affect machining results? A 1.2 mm radius increases edge strength and resistance to chipping, improving tool life in interrupted cutting and providing a balance between surface finish and robustness. Is this insert compatible with standard ISO holders? Yes, the insert follows the ISO designation DCMT11T312 and is compatible with holders and boring bars designed for that form, provided the holder matches form, relief angle, tolerance class, fastening type, size and thickness. What does the hole design contribute to the setup? The cylindrical hole with a single-sided countersink (40°–60°) enables secure clamping and precise positioning in standard clamping assemblies, reducing the risk of insert movement during heavy cuts. Why choose the AH6235 grade for production? AH6235 is a tougher, PVD-coated carbide grade that offers improved edge security and stable chip formation in rostfreier Stahl, making it suitable for applications with increased breakout risk and interrupted cuts. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
DCMT 11T312 AH6235 Wendeplatten - Tungaloy
Take advantage of the combination of a PVD-coated cemented carbide grade and a 1.2 mm corner radius for improved resistance to chipping in interrupted cuts; the insert delivers robust performance on stainless steels and integrates easily into ISO-compatible holders — order via Metav Werkzeuge or consult our specialists for application advice. DCMT DCMT11T312 AH6235 indexable turning insert for Turning by Tungaloy DCMT11T312 AH6235 Tungaloy indexable insert is a 55° rhomboid insert designed for external and internal turning, optimised for stainless steels and interrupted cutting conditions DCMT11T312 - 55° rhombic insert PVD-coated cemented carbide AH6235 1.2 mm corner radius for robust edges Suitable for stainless steel and interrupted cuts Reliable ISO compatibility reduces set-up time and uncertainty The insert is manufactured to ISO-standard dimensions, which means compatibility with a broad range of commercially available holders is determined by form, clearance angle, tolerance class, clamping method, size and thickness rather than bespoke geometries. This standardisation supports rapid replacement and fewer toolholder variants on the shop floor, lowering inventory complexity. For production planners this translates into reduced machine downtime, consistent fixturing and predictable changeover times. The relief angle of 7° and the rhomboid geometry ensure a known datum for toolsetting and repeatable positioning in both solid bar turning and boring applications. Tough PVD-coated grade engineered for stainless steels and tough alloys The cutting grade AH6235 is a PVD-coated cemented carbide chosen for its toughness and resistance to edge breakdown, especially where interrupted cuts or work-hardening materials like stainless steel are encountered. The coating promotes thermal resistance and adhesion while the substrate provides plastic deformation resistance, which together reduce crater wear and the risk of premature chipping. The combination extends tool life under unstable cutting conditions and contributes to consistent productivity and lower unit costs per component when compared with uncoated or less resilient grades. Geometry and clamping for secure mounting and improved chip control The 55° included angle of the rhomboid insert and the 1.2 mm corner radius deliver a practical compromise between edge strength and access to detail work. The insert is supplied with a cylindrical hole and a single-sided countersink (40°–60°) for positive seating and secure clamping in a wide range of ISO-compatible toolholders. A one-sided chipbreaker supports controlled chip formation for turning operations, helping to avoid long, stringy chips in many stainless-steel machining scenarios. The plate thickness of 3.97 mm and size code 11 provide rigid support under moderate depths of cut and are well suited to both external and internal turning tasks where stability is a priority. Operational benefits and application guidance for shop-floor decision makers In everyday production the combination of a robust carbide substrate, a PVD barrier coating and an effective chipbreaker results in fewer interruptions from edge failure and more predictable component quality. Typical applications include outer diameter profiling, shoulder turning and light boring where interruptions or built-up edge may occur. For best results, select a holder that matches the insert’s form and tolerance class and adapt cutting parameters to account for the tougher grade — lower cutting speeds and increased feed per revolution are often beneficial at the start when finishing work-hardened stainless steels. The insert’s geometry and mounting design simplify inventory planning and make it a pragmatic choice for job shops and series production alike. For application-specific recommendations and supply, contact Metav Werkzeuge for technical guidance and availability — eMail: info@metav-werkzeuge.com | Tel: +49 2822 7131930 Technical data Article number: 6903473 Manufacturer SKU: TUN6903473 Label: DCMT11T312 AH6235 Tungaloy‑indexable insert Material: Cemented carbide Core data Corner radius: 1.2 mm Included angle: 55° Relief angle: 7° Thickness: 3.97 mm Size code: 11 ISO designation: 11T312 Features PVD coating Grade AH6235 (tough grade for stainless steels) Rhomboid (55°) insert shape One-sided chipbreaker With hole: cylindrical hole + single-sided countersink (40°–60°) Intended application: Turning (external and internal) Compatibility criteria: form, clearance angle, tolerance class, clamping, size, thickness FAQ What workpieces is this insert best suited for? The DCMT11T312 AH6235 Tungaloy indexable insert is optimised for machining stainless steel and for operations with interrupted cuts, offering improved edge toughness and reduced breakout risk. Which holders are compatible with this ISO insert? Compatibility depends on holder form and specifications; select an ISO-compatible turning holder matching the insert’s 55° rhomboid form, 7° relief and size code 11 to ensure correct seating and clamping. How does the AH6235 grade affect cutting parameters? The AH6235 PVD-coated cemented carbide grade provides enhanced toughness; initial cuts typically use moderate speeds and slightly increased feed to avoid built-up edge, then parameters can be optimised for cycle time while monitoring wear. Is the insert suitable for internal boring as well as external turning? Yes; the insert’s geometry, thickness and secure hole mounting make it suitable for both external and internal turning, provided the chosen holder permits the required reach and clearance. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
DCMT 11T312 AH725 Wendeplatten - Tungaloy
Choose the DCMT11T312 AH725 insert for dependable, universal turning of mixed steels; the PVD-coated carbide grade delivers stable chip control and strong fracture resistance while the 1.2 mm nose radius supports consistent surface finish. Order the insert directly via Metav Werkzeuge or consult our application specialists for machining parameter advice. DCMT 11T312 AH725 — ISO turning insert for Turning, Tungaloy The DCMT11T312 AH725 is an ISO-indexed turning insert designed for external and internal turning, offering a universal, fracture-resistant grade suited to machining Stahl and rostfreier Stahl. ISO insert DCMT 11T312 AH725 PVD-coated carbide, universal for Stahl Single-sided chipbreaker, with centre hole 1.2 mm nose radius, 7° relief angle High-performance cutting for mixed steels and rostfreier Stahl The combination of a PVD-coated carbide substrate and the AH725 grade provides a balanced performance profile: wear resistance for longer tool life and toughness to resist chipping under interrupted cuts. This results in improved process security and predictable tool-change intervals in batch and serial production. For operations that alternate between different steel types, the insert maintains dimensional stability and reduces scrap through consistent cutting behaviour. Stable machining and simple clamping for reliable results With a single-sided chipbreaker and a 1.2 mm nose radius, the geometry promotes controlled chip formation and repeatable surface quality on shafts and bores. The insert’s 7° relief angle and rhombic shape support secure seating in standard ISO holders, while the centre hole with a cylindrical bore and one-sided countersink (40°–60°) enables positive clamping and rapid replacement. The design focuses on making setup and tool changes efficient, thereby reducing non-productive time and improving overall throughput. Clear compatibility and practical workshop integration The insert is part of an ISO-based system: proper matching to a holder depends on form, tolerance class, relief angle, fastening and thickness. Typical setups comprise an ISO turning insert, a compatible external holder or boring bar, and the appropriate clamp set and replacement screws. The rhombic geometry and the specified dimensions simplify selection for common turning tasks; material guidance identifies suitability for Stahl and rostfreier Stahl, helping to choose cutting parameters and coolant strategies that favour tool life and surface finish. For machining tasks demanding reliable, universal performance from Tungaloy’s AH725 grade, contact Metav Werkzeuge for tailored application support and prompt supply of the DCMT11T312 insert. Technical data Article number: 6864989-Tungaloy Manufacturer article number: 6864989 Manufacturer SKU: TUN6864989 Model series: ISO turning indexable inserts Material: carbide Brand: Tungaloy Facts Size: 11 mm Thickness: 3.97 mm Corner radius: 1.2 mm Relief angle: 7° Cutting/approach angle: 55° Hole: with hole Hole style: cylindrical hole + one-sided countersink (40°–60°) Chipbreaker: single-sided Special features Grade: AH725 Coating: PVD Geometry: rhombic Application: external and internal turning; suitable for Stahl and rostfreier Stahl Compatibility: ISO form, tolerance class, fastening, size, thickness determine holder match FAQ What materials is this insert suitable for? The DCMT11T312 AH725 insert is formulated for machining Stahl and rostfreier Stahl; the AH725 PVD-coated carbide grade combines toughness and wear resistance for mixed-steel applications. Which holders fit this ISO insert? Compatibility requires matching the ISO form, relief angle, tolerance class, fastening method, size and thickness; the insert is intended for standard ISO turning holders and boring bars and is listed under SKU 6864989-Tungaloy. What are the key geometry values for cutting data? The insert has a 1.2 mm corner radius and a 7° relief angle, with a plate thickness of 3.97 mm and a cutting angle of 55°, which should be used when calculating feeds and depths of cut. Is the insert single- or double-sided and how is it clamped? This is a single-sided insert featuring a single-sided chipbreaker; it is supplied with a cylindrical centre hole and a one-sided countersink (40°–60°) for positive clamping in ISO-compatible seats. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
DCMT 11T312 AH725 Wendeplatten - Tungaloy
Take advantage of the combination of PVD-coated carbide durability, 55° rhombic geometry for versatile turning and a secure, centred clamping design to maintain stable chip control and reduce downtime; order the insert directly via Metav Werkzeuge or request personalised advice from our consultants. DCMT 11T312 AH725 – ISO turning insert for external and internal turning, Tungaloy DCMT11T312 AH725 is an ISO-standard, rhombic turning insert designed for reliable external and internal turning operations in steel and stainless steel, featuring a centred hole and a 55° cutting geometry. PVD-coated carbide for robust cutting Universal grade AH725 for steel and stainless steel Rhombic 55° geometry for versatile turning Cylindrical hole with single-side countersink for clamping Proven geometry for reliable external and internal turning The 55° rhombic geometry delivers a balanced combination of cutting edge strength and access to diverse contour profiles, ideal for both external turning and light internal turning. Manufactured as an ISO-standard insert, this design allows for predictable chip flow and reduced vibration when matched with a suitable holder. The PVD-coated carbide grade AH725 offers improved wear resistance and fracture toughness, which is particularly beneficial when processing mixed batches or when small toolholders are used. This results in steadier surface finishes and fewer interrupted cycles, helping to keep production stable. Compatibility and secure clamping to shorten setup time Compatibility to the toolholder is defined by form, relief angle, tolerance class, fastening method, size and thickness; the insert’s cylindrical centre hole with a single-side countersink (40°–60°) ensures repeatable, secure seating and simplified replacement. With a plate thickness of 3.97 mm and size 11, the insert fits common ISO turn-holders when the 7° relief angle and tolerance are matched. The 1.2 mm corner radius provides a compromise between edge strength and detail reproduction, reducing the need for frequent edge dressing and helping to preserve dimensional accuracy during longer production runs. Lower tooling costs through consistent wear performance The chosen grade AH725 is a universal, chip-resistant solution that combines process reliability with broad material coverage for steel and stainless steel, which reduces inventory complexity and changeover time. The PVD coating decreases flank wear and extends cutting life under varied cutting conditions, while the carbide substrate maintains edge integrity against mechanical shocks. For operations demanding predictable cycle times and surface quality, this insert contributes directly to improved first-pass yield and longer intervals between indexings, supporting efficient, cost-conscious machining without sacrificing performance. For immediate availability and expert application advice on Tungaloy AH725 turning inserts, contact Metav Werkzeuge for tailored recommendations and delivery options. Technical data Article number: 6856782 Manufacturer SKU: TUN6856782 Our SKU: 6856782-Tungaloy Material: Hartmetall Facts Size: 11 Plate thickness: 3.97 mm Corner radius: 1.2 mm Cutting angle: 55° Relief angle: 7° Special features Grade/coating: AH725, PVD-coated carbide Plate form: Rhombic Hole: Cylindrical hole + single-side countersink (40°–60°) Application: Turning (external and internal) System: ISO turning insert series FAQ What materials is this insert suitable for? The DCMT11T312 AH725 insert by Tungaloy is designed primarily for steel and stainless steel, benefiting from the AH725 grade’s universal, chip-resistant properties. How does the hole and countersink design help in clamping? The cylindrical centre hole with a single-side countersink (40°–60°) ensures stable seating and repeatable clamping when used with compatible ISO external holders for turning inserts such as the Tungaloy DCMT11T312 AH725 (SKU TUN6856782). What advantage does the 1.2 mm corner radius offer? A 1.2 mm corner radius increases edge strength and reduces the risk of chipping, supporting consistent surface quality and longer tool life during continuous turning operations with the AH725 grade. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
DCMT 11T312 AH725 Wendeplatten - Tungaloy
Benefit from the DCMT11T312 AH725's combination of a PVD‑coated, breakage‑resistant carbide grade and ISO‑standard rhombic geometry to secure consistent turning performance across steels and stainless steels; order directly via Metav Werkzeuge or consult our specialists for matching recommendations. DCMT 11T312 AH725 – ISO turning insert for external and internal turning (Tungaloy) A DCMT11T312 AH725 rhombic turning insert engineered for reliable external and internal turning operations, offering universal performance and high process security across a range of steels and stainless steels PVD-coated, breakage-resistant grade AH725 ISO-standard rhombic insert, 55° lead 1.2 mm corner radius for robust edges Cylindrical hole with 40°–60° countersink Consistent results from a universal, resistant grade The AH725 grade is a PVD‑coated carbide designed for universality and resistance to edge breakouts, which translates into stable chip formation and reliable performance when machining varying workpiece materials. In everyday shop use, this reduces unexpected tool failures and supports repeatable quality in both short runs and mixed‑material batches. The grade’s robustness is particularly advantageous for smaller tooling assemblies and for operations where process security is critical, as it maintains edge integrity under fluctuating cutting conditions. Fast integration and interchangeability with ISO geometry The insert’s ISO designation and rhombic form enable straightforward replacement and compatibility with a wide range of external holders and boring bars. Key geometry details such as the 55° lead angle, 7° clearance, 1.2 mm corner radius and a 3.97 mm plate thickness ensure predictable seating and cutting behaviour. The insert features a cylindrical hole with a single‑sided countersink (40°–60°), which supports secure clamping and consistent reference positioning. Because compatibility depends on form, clearance angle, tolerance class, fastening, size and thickness, specifying these values simplifies tooling choices and minimises setup time. Practical shop‑floor benefits: fewer interruptions, better throughput Using a universal, breakage‑resistant grade means fewer tool changes and reduced machine downtime, yielding measurable productivity gains. The rhombic plate form and single‑sided chipbreaker are balanced for controlled chip flow in common turning tasks, helping to avoid chatter and improve surface finish on steel and stainless steels. For varied materials or higher demands on process stability, selecting the appropriate chipbreaker and the AH725 grade delivers reliable tool life and consistent component quality, supporting cost‑effective production and predictable maintenance cycles. Opt for the Tungaloy AH725 DCMT insert for secure, universal turning — contact Metav Werkzeuge for ordering and technical matching at info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: 6856711-Tungaloy SKU: 6856711-Tungaloy Manufacturer SKU: TUN6856711 Manufacturer article number: 6856711 Manufacturer: Tungaloy Model series: ISO-Drehwendeschneidplatten Material: Carbide Facts Lead angle: 55° Clearance angle: 7° Thickness: 3.97 mm Corner radius: 1.2 mm Insert size: 11 Hole style: cylindrical hole + one-sided countersink (40°–60°) Special features PVD-coated carbide grade AH725 Universal, breakage-resistant for steel and stainless steels Rhombic plate form Single-sided chipbreaker Compatibility depends on form, clearance, tolerance class, fastening, size and thickness FAQ Is this insert suitable for stainless steels? The AH725 grade is formulated for steels and stainless steels; the insert provides improved resistance to edge breakouts during turning of these materials. What are the key geometry values to check for holder compatibility? Check the insert’s form, 55° lead, 7° clearance, 1.2 mm corner radius and 3.97 mm thickness to ensure a correct fit with the selected holder. Can this insert be used for internal turning as well as external turning? Yes, the rhombic form and chipbreaker make the insert suitable for both external and internal turning applications when paired with an appropriate holder. Which chipbreaker is installed and when should it be changed? This item is supplied with a single-sided chipbreaker; choose an alternative chipbreaker if the workpiece material or stability requires different chip control. How is the product identified for ordering? Order by the designation DCMT11T312 AH725 (SKU 6856711-Tungaloy) and reference the AH725 grade for matching the intended material and application. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
DCMT 11T312 AH8005 Wendeplatten - Tungaloy
DCMT11T312 AH8005 Drehwendeschneidplatte von Tungaloy Die DCMT11T312 AH8005 ist eine ISO-genormte Drehwendeschneidplatte für präzises Drehen von hitzebeständigen Legierungen und harten Werkstoffen. ISO-genormt für einfache Halterkompatibilität PVD-beschichtetes Hartmetall AH8005 Speziell für hitzebeständige Legierungen Rhombische Platte, Größe 11 mm Zylindrisches Loch mit 40°–60° Senkung Produktivität und Prozesssicherheit erhöhen Mit der DCMT11T312 sorgt die Kombination aus PVD-beschichtetem Hartmetall und einer verschleißfesten Sorte für konstante Schnittleistung bei stabiler Bearbeitung. Die Platte ist für produktive Zerspanung ausgelegt und reduziert Stillstand durch längere Standzeiten und zuverlässige Spanbildung. Anwender profitieren von höherer Ausbringung bei gleichbleibender Oberflächenqualität, weil die Sorte AH8005 speziell für hitzebeständige Legierungen entwickelt wurde. Präzision und Verschleißfestigkeit im Dauereinsatz Die einseitige Spanbrecher-Geometrie unterstützt kontrollierte Spanform und sorgt für sichere Spanabfuhr auch bei schwierigen Werkstoffen. Die PVD-Beschichtung (Physical Vapor Deposition) erhöht die Verschleißfestigkeit der Schneidkante und verbessert die Wärmebeständigkeit im Schnitt. Durch den Eckenradius von 1,2 mm lassen sich definierte Schnittkanten realisieren, die eine reproduzierbare Maßhaltigkeit und gute Oberflächengüte ermöglichen. Kompatibilität, Anwendung und Auswahlhinweise Als ISO-Drehplatte passt die rhombische Form mit 55° Winkel und Freiwinkel von 7° in viele genormte Außenhalter und Bohrstangen; die Kompatibilität hängt von Form, Größe und Dicke ab. Die Platte ist mit zylindrischem Loch und einseitiger Senkung ausgeführt, wodurch eine sichere Befestigung gewährleistet ist. Für Außen- und Innendrehen empfehlen sich Halter mit passender Toleranzklasse; bei Unsicherheit hilft die technische Beratung weiter. Empfehlung: DCMT11T312 AH8005 von Tungaloy für produktive und prozesssichere Drehbearbeitung wählen; bei technischen Fragen eMail info@metav-werkzeuge.com oder Telefon +49 2822 7131930 kontaktieren Produktmerkmale Artikelnummer: 6747780 Marke: Tungaloy Serie: ISO-Drehwendeschneidplatten Bezeichnung: DCMT11T312 AH8005 Tungaloy-Wendeplatte Hersteller-SKU: TUN6747780 Daten Eckenradius: 1,2 mm Winkel: 55° Freiwinkel: 7° Plattendicke: 3,97 mm Plattengröße: 11 mm Besonderheiten Material: Hartmetall Beschichtung: PVD (Physical Vapor Deposition) Sorte: AH8005 Schneidstofftyp: PVD-beschichtetes Hartmetall Plattenform: rhombisch Loch: mit Loch Lochstil: zylindrisches Loch + einseitige Senkung (40°–60°) Spanbrecher: einseitig Einsatz: Drehen FAQ Für welche Werkstoffe eignet sich die DCMT11T312 AH8005 am besten? Die DCMT11T312 AH8005 von Tungaloy ist ausgelegt für hitzebeständige Legierungen und harte Werkstoffe; die verschleißfeste Sorte AH8005 bietet gute Standzeit und stabile Spanbildung bei diesen Werkstoffen. Ist die Platte mit allen ISO-Außenhaltern kompatibel? Die Platte ist ISO-genormt, die Kompatibilität zu Haltern richtet sich nach Form, Freiwinkel, Toleranzklasse, Befestigung, Größe und Dicke; die DCMT11T312 passt in gängige Halter mit entsprechender Aufnahme. Welche Vorteile bietet die PVD-Beschichtung bei dieser Wendeplatte? Die PVD-Beschichtung erhöht die Verschleißfestigkeit und Wärmebeständigkeit der Schneidkante, wodurch die DCMT11T312 AH8005 längere Standzeiten und konstante Bearbeitungsergebnisse ermöglicht. Wie wirkt sich der Eckenradius von 1,2 mm auf das Drehbild aus? Der Eckenradius 1,2 mm sorgt für stabile Schnittkanten und eine reproduzierbare Maßhaltigkeit; er ist geeignet, um eine gute Oberflächengüte bei robusten Schneidebedingungen zu erzielen. Worauf sollte bei der Auswahl des Spanbrechers geachtet werden? Bei der DCMT11T312 ist ein einseitiger Spanbrecher angegeben; die Auswahl sollte nach Werkstoff, Bearbeitungsart und Stabilität erfolgen, um kontrollierte Spanform und sichere Spanabfuhr zu gewährleisten. Hersteller: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Geschützte Markenzeichen und Warenbezeichnungen liegen im Recht ihrer jeweiligen Eigentümer. Markennamen und geschützte Warenzeichen werden ausschließlich zu Erklärungszwecken genannt. Es besteht keinerlei Verbindung zwischen unserem Unternehmen und den genannten Marken. Es handelt sich bei dem angebotenen Artikel um originale fabrikneue Waren des Herstellers.
DCMT 11T312 AH8005 Wendeplatten - Tungaloy
The combination of a PVD-coated AH8005 grade and a 1.2 mm corner radius delivers reliable edge life and productive turning in demanding materials; compatibility with ISO holders ensures predictable clamping and fast insert changes. Order this insert directly via Metav Werkzeuge or consult our specialists for application support. DCMT11T312 AH8005 indexable turning insert — PVD-coated carbide, 1.2 mm radius | Tungaloy The DCMT11T312 AH8005 Tungaloy insert is a PVD-coated carbide indexable insert for stable external and internal turning of heat-resistant alloys and hard materials. DCMT 11T312 geometry, ISO standard PVD-coated carbide grade AH8005 1.2 mm corner radius for strong edge Cylindrical hole with 40°–60° countersink Consistent edge life for demanding materials The combination of a PVD-coated surface and the AH8005 carbide grade is engineered for wear resistance when machining heat-resistant alloys and other hard workpiece materials. The PVD layer reduces flank wear and helps maintain a sharp cutting edge at elevated temperatures, which means fewer index changes and longer uninterrupted machining cycles. For production environments this translates into improved process stability and lower overall tooling consumption per component, supporting efficient batch runs and predictable throughput. Secure clamping and predictable repeatability The rhombic form with the 11 mm inscribed circle and the 3.97 mm plate thickness is designed to match ISO holders and boring bars; compatibility depends on form, clearance angle, tolerance class, fastening, size and thickness. The insert features a cylindrical hole with one-sided countersink (40°–60°) for reliable seating and torque transmission in standard clamps. A 7° clearance angle and the 55° included angle ensure a robust cutting geometry that resists edge chipping under interrupted cuts, while the 1.2 mm corner radius balances edge strength and surface finish for many turning operations. Better chip control and fewer rework cycles The one-sided chipbreaker offers controlled chip formation for a wide range of turning tasks, reducing the risk of long swarf and making coolant and chip evacuation more efficient. Controlled chips and stable cutting conditions help achieve a consistent surface quality and reduce secondary operations. Selecting the appropriate chipbreaker and the AH8005 grade according to workpiece material and machine stability helps to maximise tool life and machining economy, particularly for medium-to-high cutting speeds with heat-resistant alloys. Fast integration into existing tool systems As part of an ISO insert system, the plate forms a complete tooling solution with the matching external holder or boring bar, shim/clamp set and replacement screws. Systematic replacement and straightforward geometry identification reduce setup times and simplify inventory management. Clear labelling with the ISO designation 11T312 and manufacturer references speeds up reordering and ensures the correct grade and geometry are used for each application, supporting consistent production quality. Contact Metav Werkzeuge for application advice or to order the Tungaloy DCMT11T312 AH8005 indexable insert; email info@metav-werkzeuge.com or call +49 2822 7131930 Technical Data Manufacturer article number: 6747774 SKU: 6747774-Tungaloy Manufacturer SKU: TUN6747774 Model series: ISO turning indexable inserts Material: Carbide Grade: AH8005 (PVD-coated) Application: Turning Core technical data ISO designation: 11T312 Size (inscribed circle): 11 mm Plate thickness: 3.97 mm Corner radius: 1.2 mm Clearance angle: 7° Included angle: 55° Design and special features Rhombic plate form Cylindrical hole with one-sided countersink (40°–60°) One-sided chipbreaker PVD coating for elevated wear resistance Suitable for heat-resistant alloys and hard materials ISO compatibility with standard holders and boring bars FAQ What materials is this insert suitable for? The DCMT11T312 AH8005 insert is intended for heat-resistant alloys and other hard materials; the AH8005 grade and PVD coating are optimised for wear resistance in such applications. How does the 1.2 mm corner radius affect performance? A 1.2 mm corner radius increases edge strength and improves resistance to chipping, which is beneficial for interrupted cuts and heavier feed conditions while still delivering a good surface finish. Which holders are compatible with this ISO insert? Compatibility is determined by insert form, clearance angle, tolerance class, fastening method, size and thickness; the insert follows ISO geometry and fits standard DCMT-compatible external holders and boring bars when those parameters match. Is the insert reversible or indexable? The component is an indexable insert with multiple cutting edges; when one edge wears, the insert can be indexed to a fresh edge to extend tool life. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
DCMT 11T312 AH8015 Wendeplatten - Tungaloy
Take advantage of the combination of balanced wear resistance and edge stability, ISO compatibility and a 1.2 mm corner radius for consistent turning results; order the insert directly via Metav Werkzeuge or consult our technical advisers for application-specific selection. DCMT11T312 AH8015 ISO turning insert for turning — Tungaloy A DCMT11T312 AH8015 indexable insert designed for external and internal turning, offering a balanced PVD‑coated carbide grade for machining heat‑resistant alloys with reliable performance. PVD-coated carbide grade AH8015 Optimised for heat‑resistant alloys Rhombic 55° geometry, 1.2 mm corner radius Central hole with cylindrical bore and countersink Reliable ISO compatibility for production stability The insert is part of the ISO series of indexable turning plates and is engineered for standardised clamping systems; compatibility depends on form, clearance angle, tolerance class, fastening method, size and thickness. This standardised approach simplifies tool changeovers and reduces setup time, supporting a stable production flow and predictable repeatability when paired with a matching holder and clamping set. Balanced grade for demanding materials The AH8015 grade is a PVD-coated carbide chosen as a first option for general machining of heat‑resistant alloys. Its balance between wear resistance and edge stability helps extend tool life in higher-temperature cutting, delivering consistent surface quality and fewer interruptions. This translates into economical performance in longer runs and reduced frequency of insert replacements. Geometry that supports versatile turning tasks The rhombic 55° geometry with a 1.2 mm corner radius and 7° clearance angle provides a versatile cutting edge for both roughing and finishing passes. With a plate thickness of 3.97 mm and a central cylindrical bore plus a countersink (40°–60°), the insert seats securely and enables reliable clamping. The single‑sided chipbreaker design promotes predictable chip control in a variety of turning setups. System considerations and application guidance As an ISO indexable insert, success depends on selecting the correct holder, insert seat and fastening hardware; the combination of holder compatibility and the insert’s features ensures repeatable results in external and internal turning. The single‑sided chipbreaker is suitable for conventional turning strategies, while the PVD coating and grade selection support demanding alloys. For application-specific advice, Metav Werkzeuge provides consultation to align insert grade and chipbreaker with material, cutting data and machine stability. For precision turning of heat‑resistant alloys, request application support from Metav Werkzeuge or order the Tungaloy DCMT11T312 AH8015 through our sales team at Metav Werkzeuge; contact info@metav-werkzeuge.com or call +49 2822 7131930 for tailored recommendations and availability. Technical data Article number: 6747775 SKU: 6747775-Tungaloy Manufacturer article number: 6747775 Manufacturer SKU: TUN6747775 Model series: ISO-Drehwendeschneidplatten Designation: DCMT11T312 AH8015 Tungaloy-Wendeplatte Facts Size: 11 mm Plate thickness: 3.97 mm Corner radius: 1.2 mm Clearance angle: 7° Geometry angle: 55° Hole style: with hole Special features Schneidstofftyp: PVD-coated carbide Single-sided chipbreaker Rhombic plate form Central hole: cylindrical bore + countersink (40°–60°) ISO-compatible indexable insert Intended application: turning (external and internal) Model designation: DCMT11T312 FAQ What materials is this insert suited for? The AH8015 grade of the DCMT11T312 insert is formulated for machining heat‑resistant alloys, offering balanced wear resistance and edge stability for such applications. How does the 55° rhombic geometry affect cutting performance? A 55° rhombic geometry delivers a versatile cutting angle for both finishing and light roughing; the DCMT11T312 geometry helps achieve consistent surface finish and adaptable cutting forces. Which holders are compatible with this ISO plate? Compatibility is determined by form, clearance angle, tolerance class, fastening and plate size; the DCMT11T312 requires a matching ISO toolholder designed for rhombic inserts with the specified bore and countersink. What benefits does the PVD coating provide? The PVD-coated carbide on this insert improves wear resistance and thermal stability during cutting, extending tool life and maintaining edge integrity under elevated cutting temperatures. Is the insert suitable for internal turning operations? Yes; the insert’s rhombic form, corner radius and secure clamping via the central bore make it suitable for both external and internal turning applications. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
DCMT 11T312 AH8015 Wendeplatten - Tungaloy
Take advantage of the PVD‑coated carbide grade AH8015 and the 1.2 mm corner radius for balanced wear resistance and edge stability in turning operations; the rhombic DCMT geometry with a 55° entry angle ensures reliable external and internal turning cycles. Order genuine Tungaloy inserts via Metav Werkzeuge or contact the consultants for application advice and tool-chip strategy. DCMT 11T312 AH8015 Turning Insert (ISO) — Rhombic, 1.2 mm Radius by Tungaloy DCMT11T312 AH8015 is an ISO‑standard rhombic turning insert for general turning of heat‑resistant alloys and similar materials DCMT 11T312 geometry, 55° entry angle PVD‑coated carbide for balanced wear resistance Single‑sided chipbreaker for stable chip control With cylindrical hole and one‑sided countersink 40°–60° Consistent cutting performance for heat‑resistant alloys The turning insert is engineered for dependable machining of demanding alloys. Its PVD‑coated carbide substrate combines hardness with a coating that reduces built‑up edge and improves wear behaviour, making this grade a first choice for heat‑resistant materials. The rhombic form and 55° approach angle produce predictable cutting forces, which helps to maintain machine stability and component tolerances during both external and internal turning. Reduced downtime through practical design features A 1.2 mm corner radius and a single‑sided chipbreaker mean fewer edge failures and more forgiving performance on interrupted cuts. The insert’s cylindrical hole with a one‑sided countersink (40°–60°) enables secure clamping in ISO holders and straightforward indexability, simplifying tool changes and minimising stoppages. These attributes translate into measurable gains in process efficiency and tool life under typical workshop conditions. Clear system compatibility and handling in ISO tool systems Supplied as an ISO‑standard turning insert, the item fits holders that match form, clearance, tolerance class, fastener type, size and thickness. The ISO‑compliant designation 11T312 and the rhombic plate shape align with common clamping systems, so integration into existing tool plans is straightforward. Specification clarity reduces setup time and allows planners to select the appropriate chipbreaker and grade for stability, workpiece material and machining strategy. Practical benefits for workshop planning and procurement The insert’s balanced combination of edge stability and wear resistance supports predictable maintenance intervals and straightforward stock management. Its PVD‑coated carbide AH8015 grade is versatile across a broad range of alloyed steels and high‑temperature materials, helping to standardise tooling families where single‑grade solutions are preferred for operational simplicity without sacrificing performance. Contact Metav Werkzeuge for tailored recommendations on insert selection, clamping options and to secure original Tungaloy turning inserts via Metav Werkzeuge; email info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: 6747781 SKU: 6747781-Tungaloy Manufacturer SKU: TUN6747781 Model series: ISO‑turning inserts Facts Designation: DCMT11T312 Grade: AH8015 Corner radius: 1.2 mm Thickness: 3.97 mm Insert size: 11 Entry angle: 55° Clearance angle: 7° Special features PVD‑coated carbide Rhombic plate form With cylindrical hole One‑sided countersink 40°–60° Single‑sided chipbreaker Intended use: Turning FAQ What materials is this insert suitable for? The DCMT11T312 AH8015 insert is intended primarily for heat‑resistant and alloyed materials; the AH8015 PVD‑coated carbide provides a balanced compromise between wear resistance and edge stability for such alloys. How does the 1.2 mm corner radius affect machining? A 1.2 mm corner radius increases edge strength and reduces the risk of chipping on interrupted cuts; with the DCMT geometry this contributes to longer effective tool life and stable surface finish. Is this insert compatible with standard ISO holders? Yes. The DCMT11T312 is ISO‑standardised; compatibility depends on matching form, clearance, tolerance class, fastener and size in the corresponding holder system. What clamping and hole style does the insert use? The insert features a cylindrical hole with a one‑sided countersink (40°–60°), designed for secure clamping and straightforward indexing in appropriate ISO clamping systems. Which chip control can be expected from this grade? The single‑sided chipbreaker provides consistent chip formation and evacuation for many turning operations, aiding process stability when combined with the AH8015 grade. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand‑new product from the manufacturer.
DCMT 11T312 AH905 Wendeplatten - Tungaloy
Take advantage of the combination of durable PVD-coated carbide, stable 55° rhombic geometry and precise clamping features for reliable, repeatable turning operations; request application advice or order original inserts through Metav Werkzeuge for fast delivery. DCMT11T312 AH905 – Indexable Turning Insert (ISO 11T312) for Turning, Tungaloy DCMT11T312 AH905 is an ISO-standard indexable insert designed for general external and internal turning, offering a balance of cutting-edge sharpness and process security for industrial machining. PVD-coated AH905 for wear resistance 55° rhombic geometry for versatile turning 1.2 mm corner radius balances finish and strength Cylindrical hole with countersink for secure clamping Consistent cutting performance through a wear‑resistant grade The insert is manufactured in the AH905 grade, a PVD-coated carbide designed for high resistance to wear and chipping. This coating and substrate combination provides a consistent cutting edge life, which reduces interruptions and tool changes in production. For workshops prioritising process security, the material selection means fewer scrap parts and more predictable batch results. The result is an economical tool life that supports steady machining cycles. Secure mounting and ISO-based compatibility for system safety Compatibility with toolholders depends on geometry, free angle, tolerance class, fixing method, size and thickness; this ISO series ensures straightforward selection of a matching holder. The insert features a cylindrical hole with a one‑sided countersink (40°–60°) that enables secure clamping and repeatable seating in the pocket. With a defined free angle of 7° and standard tolerances, the insert integrates into conventional holder systems, helping to maintain concentricity and minimise vibration during turning. Geometry optimised for balance between surface finish and edge strength The 55° rhombic plate form and 1.2 mm corner radius deliver a compromise between a sharp cutting edge and mechanical robustness: the smaller radius helps produce finer surface finishes, while the rounded corner reduces susceptibility to chipping in interrupted cuts. The one‑sided chipbreaker design supports controlled chip formation for many turning tasks, improving evacuation and reducing the risk of built-up edge. The 3.97 mm thickness adds rigidity, supporting stable cutting in both external and internal operations. Practical selection for efficient workshop production As part of the ISO indexable insert system, the insert performs best when combined with the appropriate holder, shim and fastening hardware; a properly matched assembly reduces set‑up time and improves repeatability. Choosing the AH905 grade is recommended where a sharp cutting edge and dependable process security are required. The combination of geometry, coating and stable clamping contributes to lower overall tooling costs through longer intervals between changes and consistent part quality. Contact Metav Werkzeuge today to discuss application-specific recommendations for Tungaloy indexable inserts and to obtain original parts or technical guidance via info@metav-werkzeuge.com or +49 2822 7131930 Technical Data Article number: 6879338 Manufacturer SKU: TUN6879338 SKU: 6879338-Tungaloy Model designation: DCMT11T312 AH905 Tungaloy‑insert Numbers / Core technical data Corner radius: 1.2 mm Geometry angle: 55° Free angle: 7° Thickness: 3.97 mm Size designation: 11 Designs / Special features Material: carbided insert with PVD coating (AH905) Plate form: rhombic Hole style: cylindrical hole + one‑sided countersink (40°–60°) Chipbreaker: one‑sided Application: turning Series: ISO indexable turning inserts FAQ What materials is this insert suitable for? The AH905 grade PVD‑coated carbide insert is intended for a broad range of turning tasks; the insert performs well on steels and many alloyed materials where a sharp edge and process security are required. How does the 1.2 mm corner radius affect machining results? A 1.2 mm corner radius improves edge strength compared with very small radii and helps prevent chipping, while still allowing a good surface finish in general turning operations with DCMT11T312 AH905. Which holders are compatible with this ISO insert? Compatibility depends on form, relief angle, tolerance class, fixing method, size and thickness; use holders that accept ISO 11T312 rhombic inserts and provide firm clamping to make full use of the insert’s stability. What is the benefit of the cylindrical hole with countersink? The cylindrical hole combined with a one‑sided countersink (40°–60°) ensures repeatable seating and secure clamping, reducing movement in the pocket and helping to maintain concentricity and tool life. Is this an original Tungaloy product and how to order replacements? The item is an original Tungaloy indexable turning insert (DCMT11T312 AH905). For replacements and application advice, contact Metav Werkzeuge for product availability and guidance. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
DCMT 11T312 AH905 Wendeplatten - Tungaloy
The combination of a PVD-coated AH905 grade and a 1.2 mm corner radius ensures a sharp, wear‑resistant cutting edge and consistent chip control for turning operations; order the insert directly via Metav Werkzeuge or contact the consultants for application advice. DCMT11T312 AH905 Tungaloy turning insert — PVD-coated carbide, 1.2 mm radius The DCMT11T312 AH905 is an ISO-standard rhombic turning insert designed for reliable external and internal turning where a sharp cutting edge and process security are required. PVD-coated carbide AH905 Rhombic 55° geometry 1.2 mm corner radius Cylindrical hole with countersink Single-sided chipbreaker Consistent edge security through coating and grade The combination of the AH905 grade and a PVD coating provides a balanced resistance to wear and edge chipping while maintaining a sharp initial cutting edge. This makes the insert especially suitable where stable cutting performance is essential over longer tool life. The coating reduces friction at the cutting zone and improves heat resistance, which in turn supports more predictable tool behaviour and fewer unplanned interruptions in production. Emphasis on consistent chip formation contributes directly to process reliability and reproducible surface quality. Geometry tailored for versatile turning with reduced rework With a 55° rhombic geometry and a 1.2 mm corner radius, the insert enables a stable engagement in both external and internal turning tasks while preserving a favourable cutting edge strength. The 7° clearance angle and plate thickness 3.97 mm provide structural support that helps resist vibration and edge deformation under moderate cutting loads. These geometric features translate into tangible benefits: improved dimensional stability of finished parts and a lower likelihood of rework due to edge failure or poor surface finish. Fit, mounting and system considerations for secure use As an ISO-standard turning insert, compatibility with the toolholder depends on form, clearance angle, tolerance class, fastening, size and thickness. The insert is supplied with a cylindrical hole plus a one-sided countersink (40°–60°) for secure clamping; appropriate selection of the corresponding outside holder or boring bar is essential for achieving the full potential of the cutting geometry. A complete system typically includes the indexable insert, a matched external holder or boring bar, a backing/locating element and replacement screws to ensure consistent and repeatable mounting. Practical advantages in production environments By combining a robust substrate with an engineered chipbreaker and a modern coating, this insert delivers a favourable balance of productivity and component quality. The single-sided chipbreaker facilitates controlled chip flow in many turning scenarios, helping to reduce manual chip handling and improve cycle stability. Where a sharp cutting edge and process security are priorities, the insert supports prolonged intervals between tool changes, helping to maintain uptime and throughput in serial production or small-batch machining alike. For specification matching, batch availability and technical advice on the Tungaloy DCMT11T312 AH905 turning insert, contact Metav Werkzeuge at info@metav-werkzeuge.com or call +49 2822 7131930 for swift assistance and supply coordination Technical data Article number: 6879343 Manufacturer SKU: TUN6879343 Model series: ISO turning inserts Manufacturer: Tungaloy Data Included angle: 55° Corner radius: 1.2 mm Clearance angle: 7° Plate thickness: 3.97 mm Plate size: 11 Special features PVD-coated carbide AH905 Rhombic plate form Cylindrical hole + one-sided countersink (40°–60°) Single-sided chipbreaker Application: Turning (external and internal) FAQ Which operations are suitable for this insert? The DCMT11T312 AH905 insert is designed for external and internal turning operations where a sharp edge and process security are required. How does the AH905 grade benefit productivity? The AH905 grade combines wear resistance and chipping robustness, helping to extend tool life and maintain consistent cutting performance in turning tasks. What holder features are required for correct mounting? Correct mounting depends on matching form, clearance angle, tolerance class, fastening method, size and thickness; the insert’s cylindrical hole with countersink is intended for secure clamping in compatible holders. Can this insert be used for finishing passes? Yes — the combination of a sharp cutting edge and controlled chip formation makes the insert suitable for finishing when the chosen radius and cutting parameters align with the desired surface quality. What is the corner radius and how does it affect the cut? The corner radius is 1.2 mm, offering a compromise between edge strength and fine surface finish; a larger radius increases edge robustness, while a smaller radius tends to improve surface finish. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
DCMT 11T312 T5115 Wendeplatten - Tungaloy
Take advantage of the combination of a CVD‑coated carbide grade formulated for cast iron, a stabilising rhombic geometry and a 1.2 mm corner radius to secure consistent component finish and extended cutting performance; order or request application guidance through Metav Werkzeuge if needed. DCMT11T312 11T312 T5115 — ISO turning indexable insert for turning, Tungaloy The DCMT11T312 T5115 is an ISO‑standard rhombic indexable insert intended for external and internal turning; it combines a CVD‑coated carbide grade with a controlled geometry to balance wear resistance and edge stability in cast‑iron operations. ISO rhombic insert, 11 mm size CVD‑coated cemented carbide T5115 7° clearance angle for stable cutting Cylindrical hole with 40°–60° countersink Reliable performance for cast‑iron turning The CVD‑coated T5115 cemented carbide offers a balanced mix of wear resistance and edge stability specifically tuned for cast‑iron machining, which reduces unexpected tool changeovers and supports steady production flow. By selecting a universal grade aimed at grey and ductile cast irons, the tool life becomes more predictable and surface finish more consistent; this translates into lower rework rates and improved throughput on batch runs and single‑piece production alike. Geometry and seating for steady results The rhombic shape with an effective 1.2 mm corner radius and a 7° clearance angle gives the insert a secure seat and resilient cutting edge in standard ISO toolholders. The insert’s 11 mm size and 3.97 mm thickness are matched to common holder families; compatibility is governed by form, clearance angle, tolerance class, fastening and plate thickness. The insert features a cylindrical hole with a single‑sided countersink (40°–60°) to ensure repeatable clamping and reduced vibration, which benefits surface quality and extends insert life. System‑level approach and practical selection advice An efficient turning setup pairs the indexable plate with a suitable external holder or boring bar, plus the correct shim, clamping kit and replacement screws. Choose the one‑sided chipbreaker and grade according to workpiece material, depth of cut and machine/tooling rigidity to optimise chip control and cutting forces. For less experienced planners: a smaller corner radius improves finish on light cuts, while the 1.2 mm radius here improves edge strength for interrupted cuts or heavier stock removal. For tailored advice on using the Tungaloy DCMT11T312 with T5115 for cast‑iron turning or to arrange supply through Metav Werkzeuge, contact our technical team at info@metav-werkzeuge.com or call +49 2822 7131930 for application support and fast delivery Technical data Article number: 6864745 SKU (vendor): 6864745-Tungaloy Manufacturer SKU: TUN6864745 Core specifications Insert designation: DCMT11T312 (ISO 11T312) Size: 11 mm Corner radius: 1.2 mm Thickness: 3.97 mm Clearance angle: 7° Cutting angle: 55° Hole: cylindrical with single‑side countersink (40°–60°) Special features Material: cemented carbide Coating / grade: CVD‑coated, T5115 Shape: rhombic indexable insert Chipbreaker: one‑sided Typical application: external and internal turning Designed for cast‑iron machining System: insert + compatible holder/boring bar + shim/clamping kit + screws FAQ Which holders are compatible with this insert? Compatibility depends on holder form, clearance angle, tolerance class, fastening method, size and thickness; the DCMT11T312 insert fits standard ISO holders designed for 11 mm rhombic plates and secures via a cylindrical hole with a single‑side countersink. Is this insert suitable for interrupted cuts in cast iron? Yes; the DCMT11T312 with the T5115 CVD‑coated carbide grade provides a compromise between wear resistance and edge strength, making it appropriate for interrupted conditions in many cast‑iron applications. What chipbreaker should be selected for finishing cuts? For finishing cuts choose the finer chipbreaker variant compatible with this plate; the DCMT11T312 is supplied with a one‑sided chipbreaker, and pairing a smaller depth of cut with the same chip control geometry improves surface finish. Where can cutting data for the T5115 grade be obtained? Recommended cutting speeds and feeds for the T5115 grade are available from Tungaloy’s technical documentation and can be discussed with Metav Werkzeuge’s consultants to match machine rigidity and workpiece specifics. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
DCMT 11T312 T6215 Wendeplatten - Tungaloy
Take advantage of a CVD‑coated carbide grade designed for stainless steel turning, combined with ISO compatibility and a 55° rhombic geometry for robust, repeatable results; order directly via Metav Werkzeuge or consult our specialists for application guidance. DCMT 11T312 T6215 turning insert, 55° rhombic — Tungaloy DCMT11T312 T6215 is an ISO‑standard turning insert optimised for stable to slightly interrupted machining of stainless steels, offering a wear‑resistant CVD coating and geometry suitable for both external and internal turning. CVD-coated carbide for stainless steel machining 55° rhombic shape for versatile turning 1.2 mm corner radius for consistent edge strength Cylindrical hole with single-sided countersink High‑performance turning with fewer interruptions The CVD‑coated carbide grade T6215 delivers elevated wear resistance and stable chip formation when machining stainless steel, which helps to extend cutting edge life and maintain component quality. The coating and substrate combination reduce built‑up edge and improve heat resistance under continuous cutting, meaning fewer insert changes and longer productive runs. For best results, select the chipbreaker and grade that match the workpiece material and cutting conditions to achieve a consistent surface finish and minimal rework. Easy integration into ISO tool systems for secure clamping Designed as an ISO‑standard plate, the insert fits into compatible holders when shape, relief angle, tolerance class, fixing method, size and thickness are matched correctly. The 55° rhombic form and 7° relief support a range of turning operations, while the cylindrical hole with one‑sided countersink (40°–60°) ensures positive seating and secure clamping, reducing vibration and enhancing repeatable part accuracy. The modest 3.97 mm thickness contributes to stability in both external and internal setups. Practical gains for production efficiency A 1.2 mm corner radius provides a balance between edge robustness and cutting forces, promoting reliable tool life and consistent component tolerances. Using this insert within a complete system — insert, suitable external holder or boring bar, shim/clamping set and replacement screws — streamlines changeovers and supports predictable machining cycles. The geometry and coating support improved productivity by reducing downtime for tool changes and by delivering a repeatable surface quality across batches. For reliable stainless steel turning with Tungaloy’s wear‑resistant T6215 grade, contact Metav Werkzeuge for ordering and detailed application advice at info@metav-werkzeuge.com or call +49 2822 7131930 Technical Data Article number: 6903100 Manufacturer SKU: TUN6903100 Label: DCMT11T312 T6215 Tungaloy‑insert Manufacturer: Tungaloy Facts ISO designation: DCMT11T312 / 11T312 Angle: 55° Relief angle: 7° Thickness: 3.97 mm Size: 11 mm Corner radius: 1.2 mm Design / Special features Grade: T6215 (CVD‑coated carbide) Plate shape: rhombic Hole: with cylindrical hole and one‑sided countersink (40°–60°) Chipbreaker: one‑sided Application: turning of stainless steels; suitable for external and internal turning FAQ Which materials is this insert best suited to machine? The DCMT11T312 T6215 insert from Tungaloy is optimised for stainless steel machining under stable to lightly interrupted conditions, providing improved wear resistance and chip control. What does the 55° rhombic geometry mean for turning tasks? A 55° rhombic shape offers versatility for both external and internal turning, enabling balanced cutting forces and good edge support for general turning operations. How does the T6215 CVD coating benefit production? The T6215 CVD coating increases heat and wear resistance, which extends tool life and helps maintain surface finish during longer production runs with stainless steel workpieces. What should be checked for correct insert compatibility with holders? Compatibility depends on plate form, relief angle, tolerance class, fixing method, size and thickness; ensure the holder matches the ISO designation and the insert’s 3.97 mm thickness and hole style. Is this insert suitable for interrupted cuts? The grade and geometry are intended for stable to slightly interrupted cutting; for heavily interrupted conditions specialised grades or geometries should be considered. Manufacturer/Responsible: Tungaloy‑NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand‑new product from the manufacturer.
DCMT 11T312 T6215 Wendeplatten - Tungaloy
Benefit from a CVD-coated carbide grade that delivers consistent performance in stainless-steel turning and a 7° clearance that supports reliable chip control; the combination of durability and ISO compatibility keeps production steady. Order the insert directly via Metav Werkzeuge or consult the team for application-specific advice. DCMT DCMT11T312 T6215 turning insert (7° clearance) – Tungaloy A DCMT11T312 T6215 ISO-format turning insert designed for stable to lightly interrupted turning of stainless steels, offering a robust nose radius and secure clamping. CVD-coated carbide for extended tool life 7° clearance for predictable chip formation 1.2 mm nose radius for robust finishing Rhombic ISO insert with centre hole and countersink Durable grade for productivity and predictable performance The CVD-coated carbide grade T6215 is tailored for stainless steels, combining wear resistance with consistent edge stability under stable to lightly interrupted conditions. This results in fewer indexings and longer production runs, which improves overall process economy and reduces unexpected downtime. Selecting the right one-sided chipbreaker and matching it to the workpiece and machining parameters ensures reliable chip evacuation and stable surface quality, so machining cycles remain efficient and repeatable. Easy integration into ISO holder systems and secure clamping Designed as an ISO-format rhombic insert, the geometry and fixing details permit straightforward matching with appropriate external holders or boring bars. Compatibility depends on form, clearance angle, tolerance class, clamping style, size and thickness; the centre hole with a cylindrical bore and a one-sided countersink (40°–60°) offers positive clamping and consistent seating. The 11 mm size and 3.97 mm plate thickness support rigid fixation, while the 55° geometry contributes to accessible toolpath planning across common turning setups. Reliable surface finish and practical application advice The 1.2 mm nose radius provides a balance between edge strength and surface finish, making the insert suitable for both light finishing and controlled stock removal when stability permits. The rhombic shape and single-sided chipbreaker make tool selection intuitive for general external and internal turning tasks. If uncertainty persists regarding holder selection or cutting data, technical guidance is available—Metav Werkzeuge supplies application support and can advise on feeds, speeds and clamping options to match shop conditions. For further details, contact info@metav-werkzeuge.com or call +49 2822 7131930. Contact Metav Werkzeuge for tailored application advice and secure the Tungaloy DCMT11T312 T6215 insert for reliable stainless‑steel turning Technical data Article number: 6903098 SKU: 6903098-Tungaloy Manufacturer SKU: TUN6903098 Brand: Tungaloy Model series: ISO-Drehwendeschneidplatten Designation: DCMT11T312 Core data Nose radius: 1.2 mm Insert size: 11 mm Plate thickness: 3.97 mm Clearance angle: 7° Geometry angle: 55° Special features CVD-coated carbide grade T6215 One-sided chipbreaker Rhombic shape Centre hole with cylindrical bore + one-sided countersink (40°–60°) ISO 11T312 designation Suited to turning stainless steels under stable to lightly interrupted conditions Compatibility determined by form, clearance, tolerance class, clamping, size and thickness FAQ Which materials is this insert best suited for? The DCMT11T312 T6215 insert is optimised for stainless steels, providing wear resistance and edge stability in stable to slightly interrupted turning. How does the centre hole affect clamping? The centre hole with a cylindrical bore and a one-sided countersink (40°–60°) on the insert enables positive clamping and consistent seating in ISO-compatible holders. What does the T6215 grade signify? T6215 is a CVD-coated carbide grade formulated for wear resistance and durability during the machining of stainless steels, offering extended tool life. What nose radius and applications suit this insert? With a 1.2 mm nose radius, the insert balances edge strength and surface finish, suitable for finishing and controlled roughing when machining conditions are stable. Which specification confirms ISO compatibility? The insert carries the ISO 11T312 geometry designation and the rhombic form, which supports compatibility with ISO-standard external holders and boring bars. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
DCMT 11T312 T6215 Wendeplatten - Tungaloy
Benefit from the combination of CVD-coated carbide wear resistance and a 1.2 mm corner radius for steady, repeatable turning of stainless steels; compatible with ISO-form holders and available via Metav Werkzeuge for rapid supply or advisory support. DCMT 11T312 T6215 turning insert — Tungaloy (CVD-coated carbide, 1.2 mm radius) The DCMT11T312 T6215 is an ISO-standard indexable turning insert intended for external and internal turning of stainless steels under stable to lightly interrupted cutting conditions CVD-coated carbide for wear resistance 1.2 mm corner radius for stable cutting ISO rhombic form, size 11 Single-sided chipbreaker, with countersunk hole Consistent performance through CVD-coated carbide The CVD-coated carbide grade provides a hard, wear-resistant surface that prolongs cutting life and reduces flank wear during prolonged operation. Chemical vapour deposition (CVD) applies a thin, durable coating that resists adhesion and heat-related wear; this is especially helpful when machining tough alloys. The result is longer tool life and fewer index changes, supporting uninterrupted production and predictable maintenance intervals. Geometry and clamping that ensure process reliability An ISO rhombic insert in size 11 with a 55° approach promotes accessibility for external and internal turning while maintaining a stable cutting force direction. The insert thickness of 3.97 mm and the with-hole design — a cylindrical hole plus a one-sided countersink (40°–60°) — ensure secure clamping in compatible holders. Proper clamping reduces vibration and runout, which directly improves surface finish and dimensional repeatability in serial production. Designed chip control for stainless-steel turning The T6215 grade combined with a single-sided chipbreaker is optimised for machining stainless steels where stringy chips and work-hardening present common challenges. The chipbreaker promotes predictable chip formation and evacuation, lowering the risk of built-up edge and improving coolant access. Choosing the correct chipbreaker and grade helps to reduce secondary operations, so machining cycles become more economical and less labor-intensive. Practical handling and system compatibility for workshop efficiency A 1.2 mm corner radius balances edge strength and small-feature capability: it resists chipping on interrupted cuts while allowing fine finishing where required. The DCMT geometry and ISO designation mean the insert fits a wide range of standard turning holders; spare screws, clamping sets and matching carriers form the complete system. Clear selection of holder form, relief angle and tolerance class guarantees interchangeability and simplifies tool inventory management. Contact Metav Werkzeuge for technical compatibility checks and prompt supply of the Tungaloy DCMT11T312 turning insert — eMail info@metav-werkzeuge.com or call +49 2822 7131930 Technical Data Article number: 6903096-Tungaloy Manufacturer article number: 6903096 Manufacturer SKU: TUN6903096 Series: ISO-Drehwendeschneidplatten Application: Turning Material: Carbide Grade: T6215 Core Data Corner radius: 1.2 mm Relief angle: 7° Approach angle: 55° Thickness: 3.97 mm Insert size: 11 Special features CVD-coated carbide ISO rhombic form (DCMT) Single-sided chipbreaker With hole: cylindrical hole + one-sided countersink (40°–60°) Compatible with ISO-standard turning holders Suited for external and internal turning of stainless steels FAQ What materials is this insert best suited for? The Tungaloy DCMT11T312 in grade T6215 is optimised for turning stainless steels, offering improved wear resistance and chip control for these alloys. How does the CVD coating affect tool life? The CVD-coated carbide surface on the DCMT11T312 improves resistance to adhesion and thermal wear, extending service life compared with uncoated grades under comparable cutting conditions. What clamping types are compatible with this insert? The ISO rhombic DCMT form fits standard ISO holders that accept size 11 inserts and use a cylindrical hole with a countersunk screw seating; compatibility depends on holder form, relief angle and tolerance class. Which chipbreaker should be chosen for interrupted cuts? For stable to lightly interrupted conditions the single-sided chipbreaker supplied with this grade provides reliable chip control; match chipbreaker geometry to material and stability for best results. Is this insert suitable for fine finishing? Yes — the 1.2 mm corner radius and CVD-coated grade enable stable finishing when using appropriate feed and speed values, while maintaining edge strength for moderate interruptions. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
DCMT 11T312 T9215 Wendeplatten - Tungaloy
Take advantage of the combination of high wear resistance and reliable chip control to maintain steady productivity in medium-steel turning; the design and ISO compatibility ensure repeatable clamping and straightforward integration into existing toolsets. Order the DCMT11T312 T9215 Tungaloy insert directly via Metav Werkzeuge or ask our consultants if needed. DCMT11T312 T9215 Tungaloy insert — ISO rhomboid turning insert, CVD-coated carbide, 1.2 mm radius The DCMT11T312 T9215 Tungaloy insert is an ISO rhomboid turning insert engineered for general turning tasks on medium steel, combining a CVD-coated carbide grade with a robust chipbreaking geometry for continuous to lightly interrupted cuts. CVD-coated carbide grade T9215 1.2 mm corner radius for strength ISO rhombic plate, size 11, 3.97 mm thick Cylindrical hole with 40°–60° single-sided countersink Achieve higher uptime through durable cutting performance The CVD-coated carbide grade T9215 provides a balance of wear resistance and fracture toughness, enabling longer tool life under stable machining conditions. The coating promotes consistent edge behaviour at elevated cutting speeds, which translates into fewer insert changes and less downtime. With a 1.2 mm corner radius, the insert achieves improved edge strength that reduces the risk of premature chipping during medium-depth turning operations. This combination allows workshops to sustain production rates while controlling tool-related variables and overall process costs. Predictable clamping and simple integration in ISO systems Designed to the ISO series for turning, the insert’s rhombic form and defined parameters ensure compatibility when the cutterholder is matched by form, clearance angle and size. The 7° clearance angle, 11 size and 3.97 mm thickness are measurable interface points that determine fit; the cylindrical hole with a single-sided 40°–60° countersink secures the insert reliably under axial and radial loads. Specifying holders that accept ISO rhombic inserts with matching tolerance classes and fastening methods delivers repeatable clamping and consistent cutting geometry, which benefits process control and surface finish predictability. Better chip control and application guidance for turning The insert’s one-sided chipbreaker is tuned for medium-steel applications, producing controllable chips in continuous to light interrupted cuts and helping to protect both the tool edge and the workpiece finish. For external turning and internal profiling, choose a chipbreaker and grade that suit workpiece rigidity and the intended depth of cut; the CVD-coated substrate performs well when stability and steady material removal are priorities. Where finer finishes are required, reducing feed or selecting a smaller corner radius will improve surface quality without sacrificing reliability. For tailored advice on holder compatibility, machining parameters and optimal insert selection, contact Metav Werkzeuge via info@metav-werkzeuge.com or +49 2822 7131930; our consultants can recommend the correct insert and clamping solution for the intended turning application Technical data Article number: 6774039 SKU: 6774039-Tungaloy Manufacturer SKU: TUN6774039 Model series: ISO-Drehwendeschneidplatten WPL designation: DCMT11T312 T9215 Core data Size: 11 Thickness: 3.97 mm Clearance angle: 7° Corner radius: 1.2 mm Included angle: 55° Hole style: cylindrical hole + one-sided countersink 40°–60° Special features CVD-coated carbide grade T9215 One-sided chipbreaker Rhombic plate shape For turning (external and internal) Suitable for continuous to light interrupted cuts Compatibility determined by form, clearance angle, tolerance class, fastening, size and thickness FAQ What materials is this insert suitable for? The DCMT11T312 T9215 Tungaloy insert is optimised for medium steel machining and performs best in continuous to light interrupted cuts where the T9215 grade’s wear resistance and toughness are valuable. How can compatibility with an existing holder be ensured? Check that the holder accepts ISO rhombic inserts of size 11, 3.97 mm thickness and the 11T312 geometry; confirm the form, 7° clearance angle, tolerance class, fastening method and hole/countersink arrangement before fitting the insert. What benefits does the T9215 CVD coating provide? The CVD-coated carbide T9215 improves surface hardness and thermal stability at the cutting edge, resulting in enhanced wear resistance and reliable edge life under elevated speeds, which supports higher productivity and consistent component quality. Is the insert suitable for internal turning operations? Yes, the geometry and chip control of this indexable insert are appropriate for internal turning as well as external profiling, provided the holder and tool overhang allow for stable cutting conditions. When should the 1.2 mm corner radius be preferred or avoided? The 1.2 mm radius offers a robust edge for general turning and semi-roughing; for very fine finishing operations or when tight dimensional tolerances demand minimal tool engagement, a smaller corner radius is preferable to reduce cutting forces and improve surface finish. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
DCMT 11T312 T9215 Wendeplatten - Tungaloy
Combining the CVD-coated carbide T9215 for high wear resistance with a 1.2 mm corner radius and a secure cylindrical hole, this configuration promotes stable, high-productivity turning of medium steels; order the original insert via Metav Werkzeuge or contact the consultants for application support. DCMT 11T312 T9215 Tungaloy indexable turning insert — ISO rhombic 55° for turning A DCMT11T312 T9215 indexable turning insert designed for ISO-standard external and internal turning, optimised for medium-steel machining and secure clamping in compatible holders ISO rhombic insert, 55° cutting geometry CVD-coated carbide grade T9215 Suitable for medium steel turning Cylindrical hole with 40°–60° countersink Increased productivity through high wear resistance The CVD-coated carbide grade T9215 combines wear resistance with fracture safety to support productive machining under continuous to slightly interrupted conditions. The coating enhances edge life by reducing abrasive wear, while the substrate maintains toughness, resulting in longer tool life and fewer indexings. With a 1.2 mm corner radius the insert balances strength and surface finish, making it suitable for programmes where stability and consistent cycle times are required. Reliable clamping and repeatable setup Designed as an ISO-standard rhombic insert, the geometry and tolerance class ensure predictable fitment in compatible holders. The cylindrical hole with a 40°–60° countersink provides a secure mechanical interface that reduces micro-movement during cutting and simplifies indexing. A controlled fit—determined by form, relief angle and thickness—translates into faster set-ups and repeatable results across batches, which is especially valuable in production environments seeking reduced downtime. Practical guidance for application and tooling systems Optimised for medium steel turning, the insert performs well in both external and internal turning operations when paired with an appropriate holder or boring bar, a matching shim or clamp set and correct fastening screws. The single-sided chipbreaker supports predictable chip formation; selecting the matching chipbreaker and grade according to workpiece stability and cutting conditions improves surface quality and process reliability. The system approach—insert, holder, mount and spare screws—enables straightforward replacement and minimises inventory complexity. Choose the original Tungaloy DCMT11T312 T9215 insert through Metav Werkzeuge for consistent medium-steel performance — contact Metav Werkzeuge at info@metav-werkzeuge.com or +49 2822 7131930 for tailored recommendations Technical data Article number: 6773970 Manufacturer SKU: TUN6773970 Model series: ISO turning inserts Material: Carbide Core dimensions Insert designation: DCMT11T312 Size: 11 Thickness: 3.97 mm Corner radius: 1.2 mm Relief angle: 7° Cutting angle: 55° Hole style: cylindrical hole with one-sided countersink (40°–60°) Special features Grade/coating: T9215, CVD-coated carbide Chipbreaker: single-sided Typical application: external and internal turning System components: insert, suitable holder or boring bar, shim/clamp set, replacement screws Compatibility determined by form, relief, tolerance class, fastening, size and thickness FAQ What materials is this insert best suited for? The Tungaloy DCMT11T312 T9215 insert is specified for medium steel machining and is optimised to deliver high wear resistance and fracture safety in such applications. How does the insert ensure secure clamping? Clamping security is achieved via the cylindrical hole with a 40°–60° countersink, which provides a stable mechanical interface when mounted in a compatible holder. Can this insert be used for interrupted cuts? Yes, the T9215 grade is suitable for continuous to slightly interrupted cuts, offering a balance of toughness and wear resistance for reliable performance. Which system components are required to use this insert? A complete system typically consists of the indexable insert, a compatible external holder or boring bar, a shim or clamp set and the appropriate replacement screws to ensure correct mounting and repeatability. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
DCMT 11T312 T9225 Tungaloy Wendeplatten - Tungaloy
The robust combination of CVD-coated T9225 grade and an ISO rhombic geometry delivers consistent results in medium to heavy steel turning, especially where interrupted cuts occur; this reduces tool changes and supports stable chip formation. Order original Tungaloy inserts directly via Metav Werkzeuge or consult their specialists for grade selection and application advice. DCMT 11T312 T9225 ISO rhombic turning insert — Tungaloy, 55° lead, 7° clearance The DCMT11T312 T9225 is an ISO-standard rhombic insert designed for external and internal turning in steel, offering a universal, robust grade suited to variable engagement conditions. CVD-coated carbide T9225 for toughness Rhombic 55° geometry for versatile turning 7° clearance angle for reliable chip control Cylindrical hole with 40°–60° countersink Stable cutting performance for medium to heavy steel turning The combination of the T9225 CVD-coated carbide and the rhombic geometry provides a durable solution for demanding turning operations. The grade is engineered as a robust universal option for steel machining where changing engagement conditions or light interruptions occur; this translates into fewer tool swaps and predictable wear behaviour. The coating promotes heat resistance and reduced flank wear, so the cutting edge maintains performance over longer cycles and supports consistent part quality. Geometry and angles that improve process reliability A 55° lead angle combined with a 7° clearance angle ensures a controlled cutting action and an improved surface finish on turned components. The 1.2 mm corner radius helps distribute cutting forces, reducing edge chipping in interrupted cuts and stabilising the cut when depths vary. Compatibility with holders depends on form, clearance, tolerance class, fastening, size and thickness, so the insert’s ISO conformity simplifies selection of matching external holders or boring bars and reduces setup uncertainty. System compatibility and practical workshop benefits The insert is part of an ISO turning plate system that typically includes a matching external holder or boring bar, a shim/clamping set and spare screws for quick replacement. The DCMT11T312 features a cylindrical hole with a one-sided countersink (40°–60°) to ensure secure clamping and repeatable seating in a wide range of toolholders. With a plate thickness of 3.97 mm and clear size designation, inventory management becomes simpler and changeovers are faster, reducing downtime and increasing machine availability. Contact Metav Werkzeuge for tailored advice on selecting the right Tungaloy T9225 insert for steel turning and to arrange supply of genuine parts — email info@metav-werkzeuge.com or call +49 2822 7131930 Technical Data Article number: 6781312 Manufacturer SKU: TUN6781312 SKU: 6781312-Tungaloy Series: ISO turning inserts Designation: DCMT11T312 T9225 Tungaloy insert Facts Size: 11 Thickness: 3.97 mm Lead angle: 55° Clearance angle: 7° Corner radius: 1.2 mm Manufacturer article number: 6781312 Design & Features Material: cemented carbide Coating: CVD Grade: T9225 Shape: rhombic Hole: cylindrical hole with one-sided countersink (40°–60°) Chipbreaker: one-sided Application: turning FAQ What materials is this insert suitable for? The Tungaloy DCMT11T312 T9225 is primarily intended for steel machining; the T9225 grade and CVD coating offer robustness for medium to heavy cuts and intermittent engagement typical in steel turning. How does the 55° geometry affect machining? The 55° rhombic geometry on this turning insert reduces cutting forces in certain directions and improves versatility for external and internal turning, helping to achieve a stable surface finish and consistent chip formation. Is the DCMT11T312 compatible with standard ISO holders? Yes, the insert follows ISO standards; compatibility with a holder depends on form, clearance angle, tolerance class, fastening and thickness, so matching a compliant external holder or boring bar is recommended. What is the benefit of the cylindrical hole with countersink? The cylindrical hole with a one-sided countersink (40°–60°) ensures secure clamping and repeatable seating, which improves stability in heavy or interrupted cuts and simplifies insert indexing. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
DCMT 11T312 T9225 Wendeplatten - Tungaloy
DCMT11T312 11T312 T9225 ISO-Drehwendeschneidplatte von Tungaloy Die DCMT11T312 11T312 T9225 ist eine ISO-genormte rhombische Wendeplatte für das Außen- und Innendrehen, ausgelegt auf robuste Universalbearbeitung von Stahlbauteilen ISO-genormte rhombische Wendeplatte für Drehen CVD-beschichtetes Hartmetall für lange Standzeit Universalsorte für mittlere bis schwere Stahlbearbeitung Mit Loch und zylindrischer Senkung 40°–60° Produktive Zerspanung bei wechselnden Schnittbedingungen Die DCMT11T312 11T312 T9225 verbindet CVD-beschichtetes Hartmetall mit einer robusten Sortenwahl, sodass bei wechselnden Eingriffsbedingungen eine stabile Spanbildung erzielt wird. Das Resultat ist eine erhöhte Materialabtragsrate bei gleichzeitiger Prozesssicherheit. Anwender profitieren von reduzierten Werkzeugwechseln und verbessertem Fertigungsdurchsatz, was die Wirtschaftlichkeit der Fertigung spürbar erhöht. Praxisnahe Geometrie für sichere Klemmung und Kantenstabilität Die rhombische Plattenform mit Radius 1.2 und Freiwinkel 7° sorgt für eine belastbare Schneidkante und geringe Vibrationsempfindlichkeit. Die Plattengröße 11 und die Plattendicke 3,97 mm ermöglichen stabilen Sitz im Außenhalter oder in der Bohrstange; das Loch mit zylindrischem Kern und einseitiger Senkung (40°–60°) gewährleistet wiederholgenaue Befestigung. Diese Merkmale reduzieren Ausschuss und erhöhen die Standzeit der Schneide. Empfohlene Anwendung und Zielgruppe Die Wendeplatte eignet sich für das Außen- und Innendrehen in Werkstätten und Produktionslinien, die mittlere bis schwere Stahlbearbeitung durchführen. Durch den einseitigen Spanbrecher lässt sich die Spanform an Stabilität und Bearbeitungsart anpassen. Fertigungsbetriebe, die konstante Ergebnisse und minimale Stillstandszeiten benötigen, erzielen mit dieser Sorte eine zuverlässige Kombination aus Produktivität und Prozessstabilität. Empfehlung: Die Kombination aus hoher Standzeit und sicherer Spanbildung macht die DCMT11T312 11T312 T9225 zur wirtschaftlichen Wahl für anspruchsvolle Stahlzerspanung — bei Fragen erreichbar über info@metav-werkzeuge.com oder Telefon +49 2822 7131930 Produktmerkmale Artikelnummer: 6781207 Marke: Tungaloy Serie: ISO-Drehwendeschneidplatten Hersteller SKU: TUN6781207 Zahlen Plattengröße: 11 Plattendicke: 3,97 mm Eckenradius: 1,2 mm Freiwinkel: 7° Winkel: 55° Besonderheiten Material: Hartmetall Sorte: T9225 (CVD-beschichtetes Hartmetall) Plattenform: rhombisch Loch: mit Loch Lochstil: zylindrisches Loch + einseitige Senkung (40°–60°) Spanbrecher: einseitig Anwendung: Drehen Typische Einsatzzwecke: Außen- und Innendrehen FAQ Welche Werkstoffe lassen sich mit der DCMT11T312 Tungaloy-Wendeplatte bearbeiten? Die DCMT11T312 Tungaloy-Wendeplatte mit Sorte T9225 ist für die mittlere bis schwere Stahlbearbeitung ausgelegt und bietet gute Ergebnisse bei wechselnden Schnittbedingungen. Wie beeinflusst die CVD-Beschichtung die Standzeit? Die CVD-Beschichtung der Sorte T9225 reduziert Verschleiß an der Schneidkante und verbessert die Standzeit im Vergleich zu unbeschichteten Platten, was weniger Werkzeugwechsel bedeutet. Welche Rolle spielt der Eckenradius 1,2 mm? Der Eckenradius 1,2 mm stabilisiert die Schneidkante, verringert Kerbwirkung und eignet sich besonders für robustere Schnitte bei runder und planarer Konturbearbeitung. Ist die Platte mit gängigen ISO-Haltern kompatibel? Die Platte ist ISO-genormt; Kompatibilität hängt von Form, Freiwinkel, Toleranzklasse, Befestigung, Größe und Dicke des Halters ab. Prüfen des Halters wird empfohlen. Für welche Bearbeitungsarten ist der einseitige Spanbrecher geeignet? Der einseitige Spanbrecher eignet sich für Anwendungen mit wechselnder Eingriffssituation und unterstützt kontrollierte Spanabfuhr bei Einstech- und Planbearbeitungen. Hersteller: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Geschützte Markenzeichen und Warenbezeichnungen liegen im Recht ihrer jeweiligen Eigentümer. Markennamen und geschützte Warenzeichen werden ausschließlich zu Erklärungszwecken genannt. Es besteht keinerlei Verbindung zwischen unserem Unternehmen und den genannten Marken. Es handelt sich bei dem angebotenen Artikel um originale fabrikneue Waren des Herstellers.
DCMT 11T312 T9225 Wendeplatten - Tungaloy
Take advantage of a robust CVD‑coated carbide grade and ISO conformity to ensure stable performance in medium‑to‑heavy steel turning; the T9225 grade combines toughness and wear resistance for interrupted and variable cuts. Order the DCMT 11T312 T9225 indexable insert directly via Metav Werkzeuge or ask our consultants for application advice. DCMT 11T312 T9225 indexable turning insert for turning, Tungaloy, 1.2 mm radius, 7° clearance DCMT 11T312 T9225 is an ISO‑standard indexable insert designed for external and internal turning in industrial production; the rhombic form and secure hole seating enable reliable clamping in compatible holders. CVD-coated carbide T9225 for steel machining ISO-standard rhombic insert, 7° clearance 1.2 mm corner radius for versatile turning Cylindrical hole with 40°–60° countersink Consistent productivity for medium‑to‑heavy steel turning The combination of a CVD‑coated carbide substrate and the T9225 grade delivers increased toughness where cutting conditions vary. This makes the insert particularly suitable for turning operations that involve mild interruptions or changing engagement depths. The 1.2 mm corner radius helps distribute cutting forces, reducing edge chipping and extending tool life. For workshops seeking steady cycle times and fewer insert changes, this provides a clear efficiency gain through reduced downtime. Reliable chip control and stable cutting action A single‑sided chipbreaker geometry promotes predictable chip formation and evacuation under a range of feeds and speeds, which improves surface finish and reduces the risk of built‑up edge. The rhombic profile combined with 7° clearance gives secure cutting geometry that supports dimensional consistency on turned parts. Explaining briefly: a chipbreaker shapes the swarf away from the cutting zone, helping to avoid entanglement and improving machining safety and repeatability. Secure seating and system compatibility for production use The insert follows ISO form and sizing so compatibility depends on holder form, clearance angle, tolerance class, fastening method, size and thickness. The cylindrical hole with single‑side countersink (40°–60°) ensures reliable clamping in standard toolholders and simplifies tool change-out. With a 3.97 mm thickness and 11 mm size, the component integrates into common turning systems as part of an insert, holder, shim and screw assembly, enabling straightforward inventory and replacement management. Practical selection and handling guidance Select the T9225 grade and the single‑sided chipbreaker when working predominantly with steel and when variable cutting conditions require a tougher edge. For light finishing passes consider a smaller corner radius, while this 1.2 mm radius suits general turning and roughing. Store inserts in their original packaging, inspect seating surfaces for chips before assembly, and follow the holder manufacturer’s torque recommendations to maintain clamping integrity. These simple precautions protect quality and maximise the service life of the insert. For reliable medium‑to‑heavy steel turning with Tungaloy’s T9225 grade, contact Metav Werkzeuge for availability and tailored application advice via info@metav-werkzeuge.com or +49 2822 7131930 Technical data Article number: 6781079 SKU (manufacturer): TUN6781079 SKU: 6781079-Tungaloy Model series: ISO‑Drehwendeschneidplatten Facts Material: Carbide Coating: CVD Corner radius: 1.2 mm Relief angle: 7° Included angle: 55° Thickness: 3.97 mm Size: 11 Special features ISO designation: DCMT11T312 Grade/sort: T9225 Plate form: Rhombic Hole: with hole Hole style: Cylindrical hole + single‑side countersink (40°–60°) Chipbreaker: Single‑sided Typical application: Turning FAQ What materials is this insert suited for? The answer: The DCMT 11T312 T9225 insert is designed primarily for steel machining and performs well in medium‑to‑heavy turning conditions where toughness is required. How does the T9225 grade affect performance? The answer: The T9225 CVD‑coated carbide provides a balance of wear resistance and toughness, improving tool life under variable engagement and light interruption during turning. Is the insert compatible with standard ISO holders? The answer: Yes; the insert follows ISO form and sizing, but compatibility depends on holder form, clearance, tolerance class, fastening and thickness—verify the holder matches the insert’s DCMT11T312 geometry. What does the cylindrical hole and countersink mean for clamping? The answer: The cylindrical hole with 40°–60° countersink ensures secure seating and straightforward clamping with the correct screw and shim combination, which supports repeatable positioning. Can this insert be used for internal turning as well as external? The answer: The rhombic shape and 7° clearance make the insert suitable for both external and internal turning operations provided the toolholder offers the necessary access and rigidity. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
DCMT070202 070202 AH725 Wendeplatten - Tungaloy
DCMT 070202 AH725 — DCMT070202 AH725 Tungaloy-Wendeplatte zum Drehen Die DCMT070202 AH725 ist eine ISO-genormte, rhombische Wendeplatte für Außen- und Innendrehen und wurde für stabile Prozessabläufe bei Stahl und rostfreien Stählen entwickelt. DCMT070202 von Tungaloy PVD-beschichtetes Hartmetall Universelle Sorte AH725 für Stahl und rostfrei Rhombische Form 07, Eckenradius 0,2 mm Mit Loch und einseitiger Senkung 40°–60° Hohe Prozesssicherheit bei wechselnden Werkstoffen Die DCMT070202 kombiniert die AH725-Sorte mit PVD-Beschichtung und Hartmetall, was zu verbesserter Standzeit und gleichmäßiger Spanbildung führt. Diese Kombination reduziert Werkzeugausfälle und sorgt für konstante Schnittbedingungen, besonders bei wechselnden Werkstoffen oder kleineren Werkzeugdurchmessern. Vorteil: Höhere Ausbringung und weniger Nacharbeit. Präzise Plattengenauigkeit für sichere Halterung Die rhombische Geometrie mit 55° Winkel und einem Freiwinkel 7° gewährleistet stabilen Kontakt im Plattensitz und reproduzierbare Spanabnahme. Die Plattendicke 2,38 mm und der Eckenradius 0,2 mm unterstützen exakte Positionierung; ISO-Genormtheit erleichtert die Auswahl des passenden Außenhalters. Erklärung: Frei winkel beeinflusst Schnittwinkel und Oberflächenqualität. Zielgerichtete Spanformung und Anwendungsspektrum Der einseitige Spanbrecher sorgt für kontrollierte Spanform und einfache Spanabfuhr bei Außen- und Innendrehen. Die Sorte AH725 ist als ausbruchfeste, universelle Lösung konzipiert und bietet robuste Performance bei Stahl sowie rostfreiem Stahl. Ergebnis: Sicherere Prozesse bei variierenden Schnittdaten und zuverlässiger Übergang zwischen Schrupp- und Schlichtoperationen. Material und Beschichtung für längere Standzeit Die Kombination aus Hartmetall und PVD-Schicht erhöht die Verschleißfestigkeit und verbessert die Schneidkante gegen thermischen und mechanischen Abrieb. Für Anwender bedeutet das weniger Werkzeugwechsel und niedrigere Werkstückkosten pro Bearbeitungsstufe. Kurze Erklärung: PVD steht für Physical Vapour Deposition und liefert dünne, haftstarke Schichten zur Kantenstabilisierung. Für sichere und produktive Zerspanung empfiehlt sich die Verwendung der AH725-Sorte von Tungaloy; bei technischen Fragen berät Metav Werkzeuge gern per E‑Mail info@metav-werkzeuge.com oder Telefon +49 2822 7131930 Produktmerkmale Artikelnummer: 6856776 Marke: Tungaloy Serie: ISO-Drehwendeschneidplatten Bezeichnung: DCMT070202 AH725 Tungaloy-Wendeplatte Hersteller SKU: TUN6856776 Fakten Winkel: 55° Freiwinkel: 7° Plattendicke: 2,38 mm Eckenradius: 0,2 mm Plattengröße: 07 Besonderheiten Material: Hartmetall Beschichtung: PVD-beschichtet Sorte: AH725 (universelle, ausbruchfeste Sorte für Stahl und rostfreie Stähle) Plattenform: rhombisch Spanbrecher: einseitig Loch: mit Loch Lochstil: zylindrisches Loch + einseitige Senkung (40°–60°) FAQ Ist die Platte für rostfreien Stahl geeignet? Die DCMT070202 AH725 Tungaloy-Wendeplatte wurde gezielt für Stahl und rostfreie Stähle entwickelt; die AH725-Sorte bietet ausbruchfeste Performance und gute Spanbildung bei diesen Werkstoffen. Für welche Drehoperationen ist die Wendeplatte geeignet? Die Wendeplatte ist für Außen- und Innendrehen konzipiert; die rhombische Form und der einseitige Spanbrecher ermöglichen vielseitigen Einsatz von Schrupp- bis Schlichtbearbeitung. Was bedeutet der Eckenradius 0,2 mm für die Bearbeitung? Ein Eckenradius von 0,2 mm reduziert Schnittkräfte und sorgt für feine Konturen; er ist geeignet für genaues Schlichten und kleinere Schnittbreiten. Wie finde ich den passenden Halter für die Platte? Die Kompatibilität richtet sich nach Form, Freiwinkel, Toleranzklasse, Befestigung, Größe und Dicke; bei Unsicherheit hilft die Angabe DCMT070202 AH725 und die Herstellerartikelnummer 6856776 zur Auswahl. Welche Vorteile bringt die PVD-Beschichtung konkret? Die PVD-Beschichtung verbessert Kantenstabilität und Wärmebeständigkeit, führt zu längerer Standzeit und reduziert Kantenabriss bei anspruchsvollen Schnittbedingungen. Hersteller: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Geschützte Markenzeichen und Warenbezeichnungen liegen im Recht ihrer jeweiligen Eigentümer. Markennamen und geschützte Warenzeichen werden ausschließlich zu Erklärungszwecken genannt. Es besteht keinerlei Verbindung zwischen unserem Unternehmen und den genannten Marken. Es handelt sich bei dem angebotenen Artikel um originale fabrikneue Waren des Herstellers.
DCMT070204 070204 GH730 Wendeplatten - Tungaloy
Take advantage of the combination of high wear resistance, consistent chip control and ISO-standard compatibility for efficient turning cycles. Order genuine Tungaloy indexable inserts via Metav Werkzeuge or consult our technicians for application-specific guidance. DCMT 070204 GH730 – Indexable turning insert (Tungaloy, ISO) The DCMT070204 GH730 is an ISO-standard indexable turning insert designed for external and internal turning, providing a balance of wear resistance and cutting-edge stability. ISO-standard rhombic insert GH730 grade for wear resistance One-sided chipbreaker for controlled chips 0.4 mm corner radius, 7° clearance Durable carbide grade for longer cutting life The insert is produced in a carbide composition with the GH730 grade, engineered to combine wear resistance and edge stability. This results in reduced flank wear and more consistent part tolerances over longer tool life, so fewer interruptions for insert changes are required. The grade complements the insert geometry to withstand varying cutting loads while maintaining a reliable cutting edge, which supports predictable cycle times and reduces overall tooling costs in production environments. Precise fit and straightforward integration into ISO tool systems Designed to ISO dimensions, the rhombic indexable insert fits a wide range of holders when matching form, clearance angle and thickness. The combination of 2.38 mm thickness, rhombic shape and the with-hole design featuring a cylindrical hole plus a single-side countersink (40°–60°) ensures secure clamping and reproducible seating. The listed 7° clearance and 0.4 mm corner radius help to define the contact geometry and cutting line, enabling consistent results across repeated indexings and minimising setup rework when replacing inserts in compatible holders. Consistent chip formation and effective turning performance A built-in one-sided chipbreaker provides controlled chip formation, improving swarf evacuation and reducing the risk of re-cutting. This contributes to more stable cutting forces and better surface finish in typical turning operations. The insert’s geometry supports both external and internal turning tasks where a predictable chip pattern and robust edge are essential, particularly in automated or series production. The system approach—insert, compatible external holder or boring bar, backing plate/clamping set and replacement screws—ensures operational reliability and straightforward replacement procedures. Contact Metav Werkzeuge for expert application advice on Tungaloy turning inserts or to request compatibility checks for specific holders—email info@metav-werkzeuge.com or call +49 2822 7131930 Technical Data Article number: 6820982 Manufacturer SKU: TUN6820982 Model series: ISO turning indexable inserts WPL designation: DCMT070204 Manufacturer item name: DCMT070204 GH730 Tungaloy indexable insert Core specifications Shape size: 07 Thickness: 2.38 mm Corner radius: 0.4 mm Clearance angle: 7° Seat angle: 55° Hole style: cylindrical hole + one-side countersink (40°–60°) Design and features Grade: GH730 (Tungaloy) Material: carbide Chipbreaker: one-sided Insert shape: rhombic Application: turning (external and internal) Compatibility: ISO-standard insert dimensions and tolerances FAQ What materials is this insert intended for? The DCMT070204 GH730 indexable insert is specified for turning operations; the GH730 grade is formulated to provide a balance of wear resistance and edge stability suitable for a broad range of turning conditions. How does the insert locate in the holder? Location is achieved by the ISO-standard form and the central hole with cylindrical seat and single-side countersink; correct holder matching to the insert form, clearance angle and thickness is essential for secure clamping. What is the advantage of the one-sided chipbreaker? The one-sided chipbreaker of the insert ensures controlled chip formation, improving swarf evacuation and contributing to stable cutting forces and a consistent surface finish during turning. Can this insert be used for internal turning? Yes, the insert is designed for both external and internal turning applications when fitted to an appropriate external holder or boring bar and clamped with the correct backing plate or clamping set. How is the corner radius relevant to my machining? The 0.4 mm corner radius influences the strength of the cutting edge and the surface finish; a small radius like 0.4 mm helps achieve a compromise between edge robustness and finer surface quality for many turning tasks. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
DCMW 070204 AH120 Wendeplatten - Tungaloy
Data discrepancy: the product is listed for milling ("Fräsen") but the description and model series indicate a turning family (TurnTenFeed/Drehfamilie) — please verify the source data to ensure accuracy and consistency, as this mismatch could lead to confusion or errors in application, selection, or usage; it is crucial to confirm whether the intended operation aligns with the specified product family, as milling and turning involve distinct processes, tools, and requirements, and any misclassification might result in operational inefficiencies, incorrect tool usage, or potential damage to equipment, so a thorough review of the source data and clarification of the intended purpose is strongly recommended to avoid such issues.
Fragen zu diesen Produkten??
Mit mehr als 30 Jahren Erfahrung beraten wir Sie gerne persönlich.
Tel.: +49 2822 7131930
Mail: info@metav-werkzeuge.com