DNMG 110404 T6215 Wendeplatten - Tungaloy
Take advantage of the CVD‑coated carbide T6215 and the ISO‑standard rhombic geometry to ensure stable, wear‑resistant turning of stainless steels; the 0.4 mm corner radius and double‑sided chipbreaker provide versatile surface quality and long tool life. Order the insert directly via Metav Werkzeuge or request advice from our technical consultants. DNMG110404 T6215 — Tungaloy indexable turning insert, CVD‑coated carbide, 55° rhombic The DNMG110404 T6215 is an ISO‑standard rhombic indexable insert intended for external and internal turning, optimised for machining stainless steels under stable to lightly interrupted cutting conditions. CVD‑coated carbide T6215 for stainless steel 55° rhombic geometry, ISO compatible 0.4 mm corner radius for finishing and roughing Double‑sided, cylindrical hole, 4.76 mm thick Consistent performance through CVD‑coated carbide technology The CVD‑coated carbide grade T6215 combines a wear‑resistant surface with a tough substrate, delivering reliable service when machining stainless steel. This structure reduces flank wear and extends tool life in continuous and mildly interrupted cuts. The 55° rhombic geometry supports a balance between strength and accessibility for profiles and shoulders; the moderate 0.4 mm corner radius helps maintain edge stability while allowing near‑finished surface quality. These technical characteristics translate into fewer tool changes and more predictable cycle times on production runs. Clear guidance on compatibility and correct mounting Compatibility depends on form, clearance angle, tolerance class, fastening, size and thickness; the ISO designation and measured parameters ensure straightforward pairing with standard holders. The insert’s ISO code 110404 and 11 mm size match many commercial external holders designed for 55° rhombic plates. The plate thickness of 4.76 mm and the cylindrical mounting hole facilitate secure clamping with standard underplates, clamps and replacement screws. Correct selection of holder and clamping parts maintains repeatability and reduces the risk of chipping or axial run‑out during turning operations. Better chip control and suitability for stable to slightly interrupted cuts The double‑sided chipbreaker design provides symmetric cutting edges and effective chip formation when working with sticky or strain‑hardening materials such as stainless steels. A well‑matched chipbreaker reduces heat concentration at the cutting edge and supports continuous chip evacuation, which in turn preserves surface finish and dimensional accuracy. For slightly interrupted cuts, the combination of a robust carbide core and a controlled chipformer helps avoid catastrophic edge failure; coolant strategy and cutting parameters should be adjusted to the specific stainless grade and machine rigidity for optimal results. Practical handling, system setup and tool life considerations The insert is part of a system comprising the ISO turning insert, a corresponding external holder or boring bar, an underplate/clamping set and replacement screws. The cylindrical hole and double‑sided usage simplify inventory management by offering two usable edges per index. Grade T6215 is aimed at wear resistance under stable conditions; however, choosing the correct chipbreaker and cutting data is essential for sustained performance. Regular inspection of the cutting edge and controlled feed rates will help to maintain surface integrity and extend cumulative tool life. Contact Metav Werkzeuge for availability, matching holder recommendations and application support for the Tungaloy DNMG110404 T6215 indexable insert — email info@metav-werkzeuge.com or call +49 2822 7131930 to discuss technical options and lead times Technical data Article number: 6966134-Tungaloy Manufacturer SKU: TUN6966134 Manufacturer item number: 6966134 Model series: ISO‑Drehwendeschneidplatten Label: DNMG110404 T6215 Tungaloy‑Wendeplatte Facts Geometry angle: 55° Corner radius: 0.4 mm Clearance angle: 0° Plate thickness: 4.76 mm Plate size: 11 mm Special features Rhombic plate form CVD‑coated carbide (grade T6215) Double‑sided chipbreaker Cylindrical mounting hole ISO‑standard insert for turning Intended application: turning of stainless steels System components: insert, holder/boring bar, underplate/clamping set, replacement screws FAQ How can I check holder compatibility for this insert? Compatibility is determined by the ISO form, clearance angle, plate size and thickness; match the DNMG110404 T6215 insert to a holder specified for 55° rhombic ISO plates and the same plate thickness. Is this insert suitable for interrupted cuts? The Tungaloy T6215 grade is designed for stable to slightly interrupted cutting; heavy interruptions require a tougher grade or different geometry. Can the insert be rotated or indexed to use multiple cutting edges? Yes, the double‑sided design allows indexing to a second edge, and the cylindrical hole supports conventional clamping with an underplate and clamp set. What work materials is this insert optimised for? This insert is optimised for turning stainless steel under stable machining conditions; chipbreaker choice should match the specific stainless grade and stability of the setup. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand‑new product from the manufacturer.
DNMG 110404 T6215 Wendeplatten - Tungaloy
Benefit from a CVD-coated cemented carbide grade T6215, a double-sided chipbreaker and ISO-compliant geometry that deliver consistent performance when turning rostfreier Stahl; order the insert directly via Metav Werkzeuge or consult the technical team for application support. DNMG110404 T6215 DNMG 110404 T6215 turning insert by Tungaloy — CVD-coated carbide for rostfreier Stahl DNMG110404 T6215 is an ISO-form indexable insert designed for general turning operations, delivering wear-resistant cutting performance for rostfreier Stahl in stable to lightly interrupted conditions DNMG 110404 geometry for ISO holders CVD-coated cemented carbide T6215 Double-sided chipbreaker for stable cuts Rhombic shape with 0.4 mm corner radius Predictable cutting performance through standardised geometry The ISO-compliant rhombic geometry ensures repeatable seating and alignment in established toolholders, which reduces setup time and variances between inserts. With a double-sided chipbreaker and a cylindrical hole for secure clamping, the insert supports consistent chip formation and reliable edge engagement. These characteristics translate directly into predictable cycle times and fewer unplanned interruptions during serial turning tasks. Durable grade and coating for resistant edge life The T6215 grade combines a cemented carbide substrate with a CVD-coated surface to offer elevated wear resistance when machining rostfreier Stahl. The corner radius 0.4 mm increases edge strength for medium-finish work, while the CVD layer improves resistance to abrasive wear and built-up edge. For operators seeking longer tool life under steady cutting conditions, this configuration reduces flank wear and helps maintain dimensional accuracy across runs. Practical dimensions and holder compatibility for easy integration Designed for compatibility with ISO turning systems, the insert’s 11 mm inscribed circle and 4.76 mm thickness match common holder standards. The lead angle 55° supports a balance between radial engagement and surface finish, and the 0° clearance angle is typical for this geometry. The insert’s design simplifies spare-part selection: it pairs with conventional external holders or boring bars, a suitable shim or clamping kit and standard replacement screws, enabling fast changeovers and minimal downtime. Application guidance and process benefits This insert is optimised for external and internal turning; selecting the appropriate chipbreaker and the T6215 grade is crucial for rostfreier Stahl and similar alloys. The double-sided nature halves tooling cost per cutting edge compared with single-sided variants, supporting cost-effectiveness in production. For specific cutting parameters or to match the insert to a holder tolerance class, Metav Werkzeuge can provide practical recommendations and supplementary technical data. Contact Metav Werkzeuge for tailored machining advice and supply of the Tungaloy DNMG110404 T6215 insert; call +49 2822 7131930 or email info@metav-werkzeuge.com Technical Data Manufacturer article number: 6944593 SKU: 6944593-Tungaloy Manufacturer SKU: TUN6944593 Model series: ISO turning indexable inserts Designation: DNMG110404 T6215 Tungaloy insert Facts Size (inscribed circle): 11 mm Thickness: 4.76 mm Corner radius: 0.4 mm Lead angle: 55° Clearance angle: 0° Double-sided insert Special features Material: cemented carbide Coating: CVD-coated Shape: rhombic Hole: cylindrical hole (with hole) Chipbreaker: double-sided Application: turning; suitable for rostfreier Stahl under stable to lightly interrupted conditions FAQ What holder types are compatible with this insert? The DNMG110404 T6215 Tungaloy turning insert is compatible with standard ISO holders that accept a DNMG 11-size rhombic insert and accommodate the 4.76 mm thickness and cylindrical-hole fixing. Which materials is this grade best suited for? The T6215 grade with CVD coating is optimised for machining rostfreier Stahl under stable to lightly interrupted conditions and provides improved wear resistance compared with uncoated grades. How many usable cutting edges does the insert offer? As a double-sided DNMG insert, the product provides multiple indexed edges; flipping the insert yields additional cutting edges before replacement is required. Does the geometry influence surface finish? Yes; the 55° lead angle combined with a 0.4 mm corner radius balances edge strength and surface quality, giving predictable finishes on turned components. Is the insert suitable for internal and external turning? The insert is designed for both external and internal turning operations when matched to the correct holder and cutting parameters for the workpiece. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
DNMG 110404 T6215 Wendeplatten - Tungaloy
Take advantage of the combination of wear‑resistant CVD coating, a double‑sided chipbreaker and ISO‑compliant geometry for consistent productivity in turning operations; order the insert directly via Metav Werkzeuge or consult our advisers for application support. DNMG 110404 T6215 turning insert by Tungaloy — CVD‑coated carbide for rostfreier Stahl DNMG110404 T6215 is an ISO‑format turning insert designed for external and internal turning of rostfreier Stahl under stable to slightly interrupted cutting conditions DNMG110404 form, ISO‑compliant geometry CVD‑coated carbide T6215 for rostfreier Stahl Double‑sided chipbreaker for turning Rhombic shape, 55° cutting angle Reliable wear resistance for longer tool life The CVD‑coated carbide grade T6215 delivers significantly improved abrasion resistance compared with uncoated grades, making it a dependable choice for turning rostfreier Stahl in continuous production. The coating reduces flank wear and extends edge life under stable to moderately interrupted cuts, which in turn lowers tooling costs and reduces downtime. This grade is optimised for a wide range of stainless alloys and is particularly suited where consistent surface finish and repeatable tool life are required. Geometry engineered for controlled chips and consistent cuts A rhombic form with a 55° cutting angle and 0° clearance produces predictable cutting forces and stable engagement in both external and internal turning. The double‑sided chipbreaker offers reliable chip control across typical feed ranges for finishing and semi‑finishing, reducing the need for secondary operations. The corner radius 0.4 mm balances strength and surface quality, providing an effective compromise between edge robustness and fine edge definition for precise diameters and profiles. Seamless integration into ISO tool systems Compatibility with toolholders depends on form, clearance angle, tolerance class, fastening method, size and thickness — factors fully considered in the ISO series design. The insert is supplied with a cylindrical hole for secure fastening and integrates with the usual set‑up of an ISO‑approved holder, underlay/shim and clamping set; replacement screws and accessories complete the system. This standardisation simplifies stock management and enables fast indexation, which supports high uptime and efficient tool changeovers. Application guidance and cost effectiveness Intended for turning applications, this insert performs best in stable to slightly interrupted cuts and in processes where balanced wear resistance and surface integrity matter. Selecting the right chipbreaker and the T6215 grade helps to reduce cutting forces and maintain edge life, making the solution economically attractive for medium‑volume production runs. The combination of coating technology and geometry supports predictable maintenance intervals and contributes to lower total cost per part. Contact Metav Werkzeuge for tailored advice on integrating the Tungaloy DNMG110404 T6215 insert into existing turning cells and to select the optimal holder and chipbreaker combination Technical Data Article number: 6903035 Manufacturer SKU: TUN6903035 Manufacturer: Tungaloy Facts Corner radius: 0.4 mm Plate thickness: 4.76 mm Plate size: 11 mm Cutting angle: 55° Special features CVD‑coated carbide grade T6215 Rhombic plate form 0° clearance angle Double‑sided chipbreaker Cylindrical hole ISO turning indexable insert series Application: turning FAQ What materials is this insert suited to machine? This insert is supplied in the CVD‑coated T6215 carbide and is intended primarily for machining rostfreier Stahl in stable to slightly interrupted turning operations. How is holder compatibility determined for DNMG110404 inserts? Compatibility is determined by the insert form, free angle, tolerance class, fastening style, size and plate thickness; the DNMG110404 follows ISO conventions to ease integration with matching holders. Does the DNMG110404 offer reliable chip control? Yes, the double‑sided chipbreaker integrated into the DNMG110404 design ensures controlled chip formation for typical finishing and semi‑finishing feeds. What are the key dimensional features to check when ordering replacements? Check corner radius (0.4 mm), plate thickness (4.76 mm), plate size (11 mm) and the 55° cutting angle to ensure interchangeability with existing holders. Which SKU and article number identify this Tungaloy insert? The Tungaloy insert is listed under article number 6903035 and manufacturer SKU TUN6903035 for precise ordering. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand‑new product from the manufacturer.
DNMG 110404 T6215 Wendeplatten - Tungaloy
Benefit from the combination of the CVD‑coated T6215 grade and the 55° rhombic geometry for reliable stainless steel turning; the double‑sided chipbreaker and cylindrical hole provide stable clamping and predictable chip control. Order the DNMG110404 T6215 Tungaloy insert directly via Metav Werkzeuge or consult our advisors if technical guidance is needed. DNMG110404 T6215 — ISO indexable turning insert DNMG 110404 T6215 for stainless steel turning, Tungaloy, 55° DNMG110404 T6215 is an ISO‑standard indexable insert designed for external and internal turning of stainless steels under stable to slightly interrupted cutting conditions. CVD-coated carbide T6215 for stainless steel ISO DNMG 110404 rhombic geometry 55° Double-sided insert with chipbreaker Cylindrical hole, secure clamping, 4.76 mm thick High wear resistance for longer machining cycles The DNMG110404 T6215 benefits from a CVD‑coated carbide substrate that provides outstanding wear resistance during stainless steel operations. The coating reduces adhesion and built‑up edge formation, which translates into extended tool life and fewer interruptions for insert changes. For shops aiming to increase uptime and achieve consistent component tolerances, this grade improves process stability by controlling chip formation and reducing flank and crater wear. Precise geometry and secure clamping for repeatable finishes The rhombic 55° geometry combined with a 0.4 mm corner radius and a 4.76 mm plate thickness gives a balance between cutting strength and accessibility in tight profiles. The IC 11 mm size and the cylindrical hole ensure secure fixation in ISO‑compliant holders; the double‑sided design provides indexed reuse of the cutting edges, lowering tooling cost per part. Compatibility depends on holder form, relief angle, tolerance class, clamping method, size and thickness, ensuring a predictable fit and repeatable surface quality. Designed for productive, controllable turning operations This indexable insert and its double‑sided chipbreaker are optimised for productivity: stable cutting with reduced vibration improves surface finish and allows higher metal removal rates where rigidity permits. The grade is particularly suited to external and internal turning of stainless steels; selecting an appropriate chipbreaker and machining parameters enables efficient swarf control and consistent cycle times. The overall result is improved process control and a better cost‑benefit ratio for serial production. For an expert recommendation on using Tungaloy’s CVD‑coated T6215 inserts in specific turning operations, contact Metav Werkzeuge for personalised advice and rapid delivery — eMail: info@metav-werkzeuge.com | Tel: +49 2822 7131930 Technical Data Article number: 6966160 Manufacturer SKU: TUN6966160 SKU: 6966160-Tungaloy Designation: DNMG110404 Grade: T6215 Material: Carbide (Hartmetall) Coating: CVD-coated Series: ISO‑Drehwendeschneidplatten Core technical data IC: 11 mm Thickness: 4.76 mm Corner radius: 0.4 mm Lead/approach angle: 55° Relief angle: 0° Special features Rhombic plate shape Cylindrical hole for clamping Double-sided chipbreaker CVD-coated grade for stainless steel Suitable for external and internal turning Compatibility defined by form, relief angle, tolerance class, clamping, size and thickness FAQ Which materials are best machined with this insert? The DNMG110404 T6215 is developed primarily for stainless steel machining; the CVD coating and grade chemistry support stable cutting in a wide range of austenitic and ferritic stainless alloys. Is the insert indexed or single-use? This indexable plate is double-sided with chipbreakers on both faces, allowing the insert to be rotated or reversed to present a fresh cutting edge and extend productive life. What is the corner radius and how does it affect the cut? The corner radius is 0.4 mm, which balances edge strength and surface finish—smaller radii give finer finishes, while this radius supports moderate feeds and improved edge robustness. How is compatibility with holders determined? Compatibility depends on insert form, relief angle, tolerance class, clamping style, size and thickness; matching those parameters with the holder specification ensures safe and repeatable clamping. When should a specific chipbreaker be chosen? Select the chipbreaker based on the stainless steel grade, depth of cut and stability of the setup; the double-sided chipbreaker on this insert offers flexibility for different swarf shapes and feed ranges. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
DNMG 110404 T6215 Wendeplatten - Tungaloy
High wear resistance from the CVD-coated carbide grade and ISO interchangeability make this insert a dependable choice for turning rostfreier Stahl; the DNMG geometry with a 0.4 mm corner radius and 55° lead angle balances edge strength with surface finish. Order the DNMG110404 T6215 directly via Metav Werkzeuge or ask our consultants if needed. DNMG110404 T6215 — DNMG indexable turning insert for turning, Tungaloy A DNMG110404 T6215 indexable insert designed for precision turning and reliable chip control in industrial turning operations. CVD-coated carbide for high wear resistance ISO DNMG 110404 rhombic insert, 55° lead angle Double-sided chipbreaker for versatile cutting Central cylindrical hole for secure clamping Consistent wear resistance that extends tool life The combination of a CVD-coated carbide substrate and the T6215 grade delivers pronounced abrasion resistance suited to prolonged use in turning. The coating reduces flank wear and supports consistent cutting-edge integrity, which helps to maintain dimensional accuracy over longer tool life. By favouring durable coatings and a robust substrate, the insert reduces the frequency of index changes and tool reprofiling, contributing to steady productivity in batch and series production. Geometry and clamping for predictable performance The DNMG rhombic form with a 55° lead angle and 0° clearance angle provides a solid balance between cutting-edge strength and surface quality. The double-sided chipbreaker aids chip formation control across a range of feed rates, while the central cylindrical hole ensures secure, repeatable clamping in compatible holders. Compatibility to a specific toolholder is determined by form, clearance angle, tolerance class, fastening, size and thickness, so the ISO DNMG designation simplifies selection for standard tool systems and facilitates fast replacement. Process reliability and application focus for rostfreier Stahl Engineered for turning rostfreier Stahl under stable to lightly interrupted conditions, the insert’s 0.4 mm corner radius supports improved edge stability and consistent finishes without excessive cutting forces. The 4.76 mm thickness and rhombic profile enhance resistance to chipping during heavy engagement, while the reversible design reduces inventory by providing two usable cutting positions per indexed side. These attributes yield predictable cycle times and contribute to cost-effective machining in production environments. Contact Metav Werkzeuge for tailored application advice and to secure supply of the DNMG110404 T6215 from Tungaloy Technical data Article number: 6944644 SKU: 6944644-Tungaloy Manufacturer SKU: TUN6944644 Model series: ISO-Drehwendeschneidplatten Label: DNMG110404 T6215 Tungaloy-Wendeplatte Facts Insert size: 11 mm Thickness: 4.76 mm Corner radius: 0.4 mm Lead angle: 55° Clearance angle: 0° Double-sided insert Hole style: cylindrical central hole Special features Material: carbide Coating: CVD (T6215) Shape: rhombic (DNMG) Chipbreaker: double-sided Application: Turning Suitable for rostfreier Stahl Compatible with ISO DNMG holders FAQ Which materials is this insert intended for? The insert is designed primarily for machining rostfreier Stahl; the T6215 CVD-coated carbide provides enhanced wear resistance for such materials. How is compatibility with a toolholder ensured? Compatibility depends on the insert form, clearance angle, tolerance class, fastening method, size and thickness; the ISO DNMG designation indicates suitability with standard DNMG holders when these parameters match. What chip control can be expected from the insert? The double-sided chipbreaker promotes consistent chip formation across a range of cutting conditions, supporting controlled chips and stable machining in turning applications. How is the insert clamped in the tool? A central cylindrical hole provides secure clamping; combined with the DNMG rhombic geometry and 55° lead angle, this yields repeatable positioning and rigidity during cutting. Is the insert indexable to present fresh cutting edges? Yes, the reversible design allows re-indexing to present a fresh edge, which contributes to extended utilisation of each insert and reduced tooling costs. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
DNMG 110404 T9215 Wendeplatten - Tungaloy
Take advantage of the combination of CVD-coated carbide grade T9215 and the 55° rhombic DNMG110404 geometry for consistent tool life and high productivity in medium-steel turning; order directly via Metav Werkzeuge or request application advice from our consultants. DNMG110404 T9215 Tungaloy indexable insert for Turning — CVD-coated carbide, 55° rhombic The DNMG110404 T9215 indexable insert is an ISO-standard, rhombic turning insert designed for productive external and internal turning of medium steel under continuous to slightly interrupted cuts. ISO 55° rhombic geometry CVD-coated carbide grade T9215 Double-sided chipbreaker, economical indexing Cylindrical hole for secure clamping High productivity through wear-resistant coating and geometry The combination of a CVD-coated surface and a wear-resistant carbide substrate delivers stable cutting performance and extended edge life. The T9215 specification is tuned for medium steel machining, offering a balance between wear resistance and fracture toughness that supports higher machining throughput. This results in fewer indexings and longer intervals between tool changes, improving overall shop-floor efficiency without sacrificing surface quality. Clear compatibility and secure clamping for reliable setups As an ISO-standard insert, the DNMG110404 matches common holder systems where compatibility is defined by form, clearance angle, tolerance class, fastening method, size and thickness. The 55° rhombic form with a cylindrical hole provides secure seating in the pocket and straightforward clamping. Being double-sided allows both edges to be used, halving the cost per edge compared with single-sided solutions and supporting predictable tool management in production. Application advice for consistent cutting results This insert is suitable for both external and internal turning when machining steels; the double-sided chipbreaker helps control swarf in continuous and lightly interrupted cuts. The 0.4 mm corner radius supports versatile use from general finishing to semi-finishing passes, giving a compromise between edge strength and surface finish. For best results, pair the insert with a matching ISO external holder, select feeds appropriate to the radius and rigidity of the setup, and keep coolant or cutting fluid aligned to the process where required. Practical handling, traceability and inventory benefits The insert’s standardised dimensions — compact 11 mm size and 4.76 mm thickness — make storage and replenishment simple across common tooling systems. Identification via the manufacturer SKU and article number supports traceability in procurement and tool management; the robust carbide substrate and CVD coating contribute to reproducible component quality over batch runs. For specialised materials or highly interrupted cuts, consult for an optimised grade or chipbreaker matching the application. For application-specific cutting data, availability of the DNMG110404 T9215 and supply logistics, contact Metav Werkzeuge — eMail: info@metav-werkzeuge.com or call +49 2822 7131930 for prompt consultancy and delivery. Technical data Manufacturer article number: 6772257 SKU: 6772257-Tungaloy Manufacturer SKU: TUN6772257 Model series: ISO turning indexable inserts Material: carbide Facts Insert size: 11 mm Thickness: 4.76 mm Corner radius: 0.4 mm Insert angle: 55° Rake angle: 0° Special features CVD-coated carbide, grade T9215 ISO geometry 110404 (DNMG110404) Rhombic 55° shape Double-sided chipbreaker Cylindrical hole for clamping Suitable for external and internal turning Optimised for continuous to slightly interrupted cuts FAQ Which materials is this insert intended for? The DNMG110404 T9215 insert from Tungaloy is specified for medium steel machining and offers a balance of wear resistance and toughness suited to those materials. Can the insert be used on common ISO holders? Yes — the ISO-standard DNMG110404 geometry is compatible with holders that match the form, clearance angle and thickness; secure clamping is achieved via the cylindrical hole. How does the T9215 grade influence tool life? The T9215 CVD-coated grade provides improved wear resistance while maintaining fracture resistance, which supports longer edge life under medium-steel cutting conditions. Is the insert indexable on both sides? Yes, the insert is double-sided, enabling economical indexing and extending service intervals compared with single-sided designs. What size and radius does the insert have? The insert has an 11 mm size, a thickness of 4.76 mm and a corner radius of 0.4 mm, suitable for versatile turning operations. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
DNMG 110404 T9215 Wendeplatten - Tungaloy
Take advantage of the combination of CVD-coated carbide durability, a 0.4 mm corner radius for versatile part profiles and proven ISO compatibility to keep turning operations productive and repeatable; order the DNMG110404 T9215 insert directly via Metav Werkzeuge or consult our specialists for application-specific advice. DNMG110404 T9215 DNMG turning insert by Tungaloy — CVD-coated carbide, 0.4 mm radius DNMG110404 T9215 is a rhombic ISO turning insert designed for medium steel machining, offering a robust CVD coating and geometry suited to continuous and lightly interrupted cuts. ISO rhombic DNMG geometry, 55° approach CVD-coated carbide for wear resistance 0.4 mm corner radius for versatility Double-sided chipbreaker, cylindrical hole Productive turning with high wear resistance The DNMG110404 T9215 insert combines a CVD-coated carbide substrate with a purpose-engineered grade aimed at medium-steel applications. This composition provides a high level of wear resistance while retaining sufficient fracture toughness for demanding cycle times. For operations that favour continuous or lightly interrupted cuts, the grade supports elevated feed rates and sustained productivity without frequent index changes. The result is improved process stability and longer tool life compared with uncoated or less optimised grades. Secure fit and standardised compatibility reduce downtime Designed to the ISO standard, the rhombic geometry and specified dimensions ensure predictable compatibility with a wide range of external holders and boring bars. Key mounting characteristics — shape, relief angle, tolerance class, fixing method, size and thickness — determine the clamping match; the insert’s cylindrical hole and standard profile simplify retrofits in established tool systems. Using standardised components and replacement parts streamlines setup, reduces inventory complexity and shortens changeover cycles on the shop floor. Geometry tuned for surface finish and chip control A 55° approach angle and 0° relief angle combine with a 0.4 mm corner radius to produce consistent contact conditions and a balance between edge strength and profile accuracy. The double-sided chipbreaker promotes reliable chip formation and evacuation, reducing the risk of re-cutting and improving surface integrity on turned parts. With a plate thickness of 4.76 mm and nominal size 11, the insert provides stable support in medium-depth cuts while allowing repeatable seating and indexing. System-level benefit: predictable performance in production When used as part of a complete system — indexable insert, matching external holder or boring bar, shim/clamp set and spare fastening screws — the component helps deliver reproducible results across batches. The grade is positioned as a preferred choice for shops aiming to combine throughput and tool economy: lower change frequency, consistent surface quality and broad material applicability make the insert well suited to serial production and automated turning cells. Contact Metav Werkzeuge for tailored edge-selection advice and order support for Tungaloy turning inserts — email info@metav-werkzeuge.com or call +49 2822 7131930 to discuss the best combination for the intended application Technical data Article number: 6782312 SKU: 6782312-Tungaloy Manufacturer SKU: TUN6782312 Designation: DNMG110404 Facts Size: 11 mm Corner radius: 0.4 mm Thickness: 4.76 mm Lead angle: 55° Relief angle: 0° Double-sided chipbreaker Special features Material: Carbide Coating: CVD Hole: with hole (cylindrical) Form: rhombic Series: ISO turning indexable inserts Application: Turning FAQ What steels is this insert best suited for? The DNMG110404 T9215 insert is developed for medium steel machining, where the T9215 grade combines wear resistance and toughness for productive turning. Is the insert compatible with standard ISO DNMG holders? Yes, the rhombic DNMG110404 geometry and specified dimensions follow ISO conventions; compatibility depends on matching form, relief angle, tolerance and fastening method. How does the chipbreaker affect machining? The double-sided chipbreaker on this insert promotes regular chip formation and evacuation, improving process reliability and contributing to a consistent surface finish. How many cutting edges are available per index? As a double-sided ISO insert, the component provides reversible cutting edges per index, enabling economical use of the geometry before replacement. What thickness and corner radius should be considered for finishing passes? With a thickness of 4.76 mm and a 0.4 mm corner radius, the insert balances strength and profile control; for finer finishing, smaller radii or dedicated finishing geometries may be considered. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
DNMG 110404 T9215 Wendeplatten - Tungaloy
Take advantage of the combination of CVD-coated carbide durability and ISO compatibility for consistent, productive turning. The robust T9215 grade and double-sided chipbreaker ensure efficient machining of medium steel; order directly via Metav Werkzeuge or consult the team for application-specific advice. DNMG 110404 T9215 — DNMG110404 indexable insert for turning — Tungaloy A DNMG110404 T9215 indexable insert engineered for external and internal turning, offering a 55° rhomboid geometry and a 0.4 mm corner radius for dependable medium-steel machining CVD-coated carbide grade T9215 Optimised for medium steel machining Double-sided chipbreaker design Rhomboid 55° geometry, 0.4 mm radius Productivity through a wear‑resistant grade The core advantage is the CVD-coated carbide composition paired with the T9215 grade, developed for the middle range of steel applications. This combination brings enhanced wear resistance and breakage resistance, which translates into longer tool life and fewer insert changes during serial production. For operations running continuous to light interrupted cuts, the result is improved cycle times and more predictable tool consumption. The technical structure of the insert supports high material removal rates while maintaining surface integrity. Geometry and clamping that support precision A 55° rhomboid geometry with a 0.4 mm corner radius gives a balance between edge strength and profile control. The insert’s 0° relief angle and cylindrical hole are designed for secure seating in ISO-compliant toolholders; ISO compatibility is determined by form, clearance, tolerance class, fixing, size and thickness. The double-sided chipbreaker increases usable edges per insert, lowering part costs and simplifying inventory. Clear explanation: a chipbreaker controls chip formation to prevent tangling and protect both workpiece and toolholder, so consistent surface finish and process stability are attainable with fewer interruptions. Selection guidance and system integration for reliable results Selection should consider holder type, workpiece material and cutting conditions. The insert belongs to the ISO turning insert family and is supplied as part of a system consisting of the insert, a matching external holder or boring bar, and clamping components. The plate thickness of 4.76 mm and plate size of 11 mm are key for ensuring correct clamping and rigidity. For manufacturers aiming to standardise tooling across multiple lathes, the predictable performance of this insert supports reproducible results and efficient tool management. If additional cutting data or compatibility checks are required, the technical team at Metav Werkzeuge can provide machining recommendations. Contact Metav Werkzeuge for application advice on Tungaloy turning inserts; email info@metav-werkzeuge.com or call +49 2822 7131930 to discuss suitability and availability Technical data Article number: 6772226 SKU: 6772226-Tungaloy Manufacturer SKU: TUN6772226 Model series: ISO turning inserts Name: DNMG110404 T9215 Numbers / Core technical data Corner radius: 0.4 mm Plate thickness: 4.76 mm Plate size: 11 mm Approach angle: 55° Relief angle: 0° Designs / Special features Material: carbide Coating: CVD Grade: T9215 Chipbreaker: double-sided Shape: rhomboid Hole: with cylindrical hole Application: turning (external and internal) Suitable for medium steel and continuous to light interrupted cuts System setup: matching external holder or boring bar, clamping seat and spare screws Compatibility determined by form, clearance, tolerance class, fixing, size and thickness FAQ What materials is this insert intended for? The DNMG110404 T9215 insert is specifically designed for medium steel machining; its T9215 grade and CVD coating favour wear resistance in these applications. How does the chipbreaker affect machining? The double-sided chipbreaker on the insert improves chip control and reduces the risk of chip entanglement, which helps maintain surface quality and stable cutting conditions. Can this insert be used for both external and internal turning? Yes, the ISO geometry and the rhomboid 55° form make the insert suitable for external and internal turning operations when paired with the correct holder. How many usable edges are available on the insert? The insert features a double-sided design, providing multiple indexing positions; refer to the technical diagram for the exact count for the DNMG110404 geometry. What should be checked for holder compatibility? Verify form, relief (clearance) angle, tolerance class, fixing method, size and thickness to ensure correct seating of the DNMG110404 insert in the chosen toolholder Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
DNMG 110404 T9215 Wendeplatten - Tungaloy
Take advantage of the combination of a CVD-coated carbide grade (T9215), robust rhombic geometry and a double-sided chipbreaker to increase throughput in medium-steel turning operations. The insert’s DNMG110404 form and standard ISO sizing ensure straightforward integration into common external holders and boring bars. Order the DNMG110404 T9215 insert directly via Metav Werkzeuge or consult our specialists for tailored recommendations. DNMG 110404 T9215 — Indexable turning insert by Tungaloy, CVD-coated for medium steel DNMG110404 T9215 is an ISO‑format indexable turning insert designed for external and internal turning where a balance of wear resistance and fracture toughness is required CVD-coated carbide grade T9215 Optimised for medium steel machining Rhombic DNMG 11 × 4.76 mm form Double-sided insert with 0.4 mm radius Greater productivity for medium‑steel turning cycles The T9215 carbide grade combines a CVD coating with a substrate tailored for continuous to slightly interrupted cutting, delivering measurable gains in productivity and tool life. Where long runs and repeatability matter, this grade reduces tool change frequency through improved wear resistance while maintaining sufficient fracture resistance for typical shop‑floor disturbances. By selecting a CVD‑coated insert, machining windows widen and coolant strategies can be adapted to maximise material removal rates without compromising surface quality. Geometry and dimensions that simplify holder selection The rhombic DNMG geometry with an ISO designation of DNMG110404 offers a 55° approach angle and a compact 0.4 mm corner radius, making it suitable for finishing to light roughing passes. The plate measures 11 mm in size with a thickness of 4.76 mm and features a cylindrical locating hole for positive clamping. Because compatibility with a toolholder depends on form, relief angle, tolerance class, clamping method, size and thickness, these standardised dimensions allow predictable performance and straightforward substitution within ISO‑conforming tool systems. Material range and recommended applications This insert is the first choice for medium steel machining, where a consistent surface finish and stable productivity are required. Use the double‑sided chipbreaker arrangement to manage chips effectively during external and internal turning operations; match the chipbreaker and grade to the workpiece and the stability of the setup. For interrupted cuts or unstable workholding, choose conservative cutting parameters to benefit from the insert’s fracture‑tolerant substrate while preserving surface integrity. Integration into a reliable turning system An efficient tooling system comprises the ISO indexable insert, a compatible external holder or boring bar, the correct shim or clamping kit and replacement screws. The DNMG110404 format allows rapid replacement and inventory control, reducing downtime in production environments. Tungaloy’s manufacturing standards support consistent edge geometry and tolerance control, which helps maintain repeatable part quality across batches and operators. For specific clamping options and holder compatibility, consult technical data sheets or our sales engineers. For reliable medium‑steel performance choose Tungaloy inserts — contact Metav Werkzeuge for availability and technical matching; the Metav team can advise on holder compatibility and process parameters to integrate DNMG110404 T9215 into existing tool systems Technical data Article number: 6944640 SKU: 6944640-Tungaloy Manufacturer SKU: TUN6944640 Brand: Tungaloy Model series: ISO turning indexable inserts Facts Size: 11 Thickness: 4.76 mm Corner radius: 0.4 mm Relief angle (free angle): 0° Approach/lead angle: 55° ISO code: 110404 Designs and special features ISO designation: DNMG110404 Carbide substrate with CVD coating, grade T9215 Rhombic plate form, double‑sided chipbreaker Cylindrical locating hole (with hole) Suitable for external and internal turning Optimised for medium steel machining, continuous to slightly interrupted cuts FAQ Which materials is this insert best suited for? The DNMG110404 T9215 insert is optimised for medium steel machining; the CVD coating and substrate offer a balance of wear resistance and fracture toughness for continuous to slightly interrupted cuts. How many usable cutting edges does the insert provide? As a double‑sided DNMG insert, each plate offers multiple usable edges; the exact count depends on indexability and rotation strategy applied during machining. Does the DNMG110404 fit standard ISO holders? Yes, the DNMG110404 conforms to ISO geometry; compatibility is determined by form, relief angle, tolerance class, clamping method, size and thickness of the holder. What is the corner radius and how does it affect the finish? The corner radius is 0.4 mm; a smaller radius favours sharper detail and lower cutting forces, contributing to a finer surface finish when combined with appropriate feeds. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
DNMG 110404 T9215 Wendeplatten - Tungaloy
Take advantage of the combination of CVD-coated carbide wear resistance, a 55° rhombic geometry and a compact 0.4 mm corner radius for reliable, high-productivity turning in medium steels; order the insert directly via Metav Werkzeuge or contact their consultants for matching holder recommendations. DNMG 110404 T9215 turning indexable insert by Tungaloy — CVD-coated carbide, 55° rhombic The DNMG110404 T9215 is an ISO rhombic turning insert designed for external and internal turning of medium steel, offering a balance of wear resistance and fracture toughness for continuous to light interrupted cuts CVD-coated carbide grade T9215 Rhombic 55° ISO geometry 0.4 mm corner radius Double-sided chipbreaker, with cylindrical hole Consistent productivity through robust cutting material and geometry The combination of CVD-coated carbide and the T9215 grade delivers a high level of wear resistance while maintaining fracture toughness, making the insert particularly suited to medium steel machining where stable cutting and long tool life are priorities. The rhombic 55° geometry provides reliable approach angles for both facing and turning operations, helping to sustain cutting forces and reduce vibration. As a result, cycle times can be optimised and tool-change frequency reduced, supporting continuous production environments and improving overall throughput. Predictable integration with ISO tooling systems Compatibility depends on established parameters such as form, clearance angle (0°), tolerance class, fastening method, size and thickness. The insert follows ISO conventions and is intended to be used with a matching external holder or boring bar, plus a suitable shim and clamping set. Specifying the correct holder geometry and fastening hardware ensures accurate seating and repeatable positioning, which in turn secures part tolerances and surface quality. The insert's cylindrical hole and standard dimensions facilitate straightforward replacement within existing tool systems. Reliable chip control and surface finish for turning applications Equipped with a double-sided chipbreaker, the insert supports effective chip formation and evacuation during both external and internal turning. This feature improves chip control and reduces the risk of built-up edge, particularly in continuous cuts. For medium steels the grade and chipbreaker combination help to deliver consistent surface finishes while allowing reasonable cutting parameters to be applied. Selection of the correct chipbreaker and cutting conditions will further enhance performance in light interrupted cuts and during step-down operations. Operational benefits and selection guidance for workshop use The compact 0.4 mm corner radius provides a balance between strength at the cutting edge and the ability to achieve close tolerances and fine finishes on turned components. The insert is suitable where a combination of productivity and predictable service life is required; selecting the matching chipbreaker and holder stability will determine achievable feed and depth parameters. Technical consultation is advisable for optimised parameter selection when introducing the insert into new machines or processes to ensure the best compromise between cycle time, finish and insert life. For technical matching and immediate availability of Tungaloy CVD-coated inserts, contact Metav Werkzeuge for consultation and order processing at info@metav-werkzeuge.com or by phone at +49 2822 7131930 Technical data Article number: 6966131 Manufacturer SKU: TUN6966131 Product designation: DNMG110404 Facts Thickness: 4.76 mm Size: 11 mm Corner radius: 0.4 mm Clearance angle: 0° Shape angle: 55° Special features CVD-coated carbide, grade T9215 ISO rhombic insert Double-sided chipbreaker Cylindrical hole, with hole Suitable for medium steel, continuous to light interrupted cuts Compatible with standard ISO external holders and shims FAQ What materials is this insert best suited for? The DNMG110404 T9215 insert is optimised for medium steel applications; the T9215 grade combines wear resistance and fracture toughness for productive turning. Can the insert be used for internal and external turning? Yes, the rhombic 55° geometry and the double-sided chipbreaker allow use in both external and internal turning operations. How does the 0.4 mm corner radius affect performance? A 0.4 mm corner radius offers a compromise between edge strength and the ability to achieve fine surface finishes, supporting stable turning at moderate feeds. What determines compatibility with the toolholder? Compatibility is governed by the insert form, clearance angle, tolerance class, fastening method, size and thickness; matching the ISO specifications ensures correct seating and repeatability. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
DNMG 110404 T9215 Wendeplatten - Tungaloy
Take advantage of a CVD-coated carbide grade that combines high wear resistance with reliable fracture toughness and ISO compatibility for straightforward toolholder integration; the result is stable, productive turning in medium steel. Order the insert directly via Metav Werkzeuge or ask our consultants for holder matching and process recommendations. DNMG 110404 T9215 Turning insert by Tungaloy — CVD-coated carbide, 55° rhombic The DNMG 110404 T9215 is an ISO-format indexable turning insert optimised for medium steel machining, offering a robust CVD-coated carbide grade and a 55° rhombic geometry for versatile external and internal turning. DNMG 110404 T9215 ISO indexable turning insert CVD-coated carbide for high wear resistance 55° rhombic form with 0.4 mm corner radius Double-sided chipbreaker, suitable for continuous cuts Increased productivity and predictable tool life for medium steel The CVD-coated carbide grade T9215 delivers a clear productivity advantage for continuous and slightly interrupted cuts in medium steel. Combining high wear resistance with substantial fracture toughness, this grade reduces insert change frequency and helps maintain consistent cycle times. The double-sided chipbreaker contributes to stable chip control and repeatable surface quality, which in turn supports process reliability and predictable tool life in serial production environments. Compatibility and mounting — what matters for secure performance ISO-format inserts demand correct matching to the toolholder: form, relief angle, tolerance class, fastening method, size and thickness determine fit and stability. The rhombic 55° geometry and 0° relief angle of this design make it suitable for a wide range of external and internal turning operations; compatibility is ensured when those parameters align with the chosen holder or boring bar. Clear specification of these dimensions helps avoid vibration and runout, preserving surface finish and dimensional accuracy. Practical benefits on the shop floor and ease of use The insert’s 0.4 mm corner radius balances edge strength with achievable surface finish, making it a pragmatic choice where both tool robustness and component quality are required. Being double-sided provides economical use of the cutting edges, while the presence of a cylindrical locating hole facilitates secure clamping and quick indexing. Operators will appreciate the straightforward handling and the option to match chipbreaker geometry to the specific stability and material conditions encountered. Coating and grade explained for informed selection The CVD coating applied to this carbide substrate forms a hard, wear-resistant outer layer that resists abrasive interaction with steel workpieces and extends cutting life under appropriate cutting conditions. Compared with uncoated grades, the CVD-coated option offers improved high-temperature hardness and oxidation resistance, which is especially beneficial at higher cutting speeds. Selecting the T9215 grade means favouring a balance of wear resistance and fracture toughness for medium steel applications where productivity and edge security are priorities. Contact Metav Werkzeuge for tailored holder recommendations, application notes and fast supply of Tungaloy indexable inserts to keep production running smoothly. Technical data Article number: 6773930 Manufacturer SKU: TUN6773930 SKU: 6773930-Tungaloy Model series: ISO-Drehwendeschneidplatten Material: Hartmetall Facts Corner radius: 0.4 mm Insert designation: 110404 Relief angle: 0° Insert thickness: 4.76 mm Inscribed circle: 11 mm Geometry angle: 55° Special features Grade: T9215 (CVD-coated carbide) Double-sided chipbreaker Rhombic insert form With hole — cylindrical locating hole Application: Turning (external and internal) ISO-standard indexable insert FAQ What materials is this insert best suited for? The T9215 grade is optimised for medium steel machining; the DNMG 110404 insert from Tungaloy provides a balance of wear resistance and fracture toughness suited to continuous and lightly interrupted cuts. How does the CVD coating benefit cutting performance? A CVD-coated carbide insert like this reduces abrasive wear and improves high-temperature hardness, which helps to extend tool life and maintain consistent surface quality during higher-speed turning. Is the insert compatible with standard ISO holders? Compatibility depends on matching form, relief angle, tolerance class, fastening and thickness; the ISO-format DNMG 110404 is designed for standard ISO holders when those parameters are aligned. What does the 0.4 mm corner radius affect in practice? The 0.4 mm corner radius increases edge strength and improves resistance to edge chipping while still permitting a good surface finish; it is a practical compromise between robustness and finish requirements. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
DNMG 110404 T9215 Wendeplatten - Tungaloy
Benefit from the combination of high wear resistance, robust fracture toughness and ISO-standard compatibility for efficient turning operations; order the insert directly via Metav Werkzeuge or consult our specialists for application advice. DNMG 110404 T9215 indexable turning insert — ISO rhombic 55° geometry for turning DNMG 110404 T9215 indexable turning insert designed for external and internal turning applications, offering a balance of productivity and component protection in medium-steel machining. CVD-coated carbide T9215 grade ISO rhombic DNMG 55° geometry Double-sided chipbreaker, with cylindrical hole 0.4 mm corner radius for medium steel High productivity through a wear-resistant grade The insert features a CVD-coated carbide substrate in T9215 specification, which combines enhanced wear resistance with good fracture toughness to support prolonged cutting cycles. This material-coating combination is particularly effective in continuous and light interrupted cuts, enabling stable tool life when machining medium steel. The selected grade prioritises high removal rates and consistent edge security, so fewer interruptions for tool change contribute directly to improved process throughput. Geometry and system compatibility for reliable indexing The DNMG110404 form follows ISO conventions with a 55° rhombic geometry and a nominal 0° relief angle, giving predictable cutting behaviour and straightforward integration into standard holders. Compatibility is determined by form, relief angle, tolerance class, fastening method, size and thickness; the insert’s 4.76 mm thickness and 11 mm inscribed circle make it suitable for many common external holders and boring bars. The item includes a cylindrical locating hole for secure clamping, and the double-sided design effectively doubles available cutting edges per insert, reducing tooling costs and downtime. Process security, surface quality and application guidance A 0.4 mm corner radius provides a compromise between strength and surface finish: the larger edge radius reduces edge chipping risk while offering acceptable surface quality on typical steels. The double-sided chipbreaker supports controlled chip formation across a range of feeds, helping to avoid entanglement and promoting stable evacuation. In practice, this insert is specified for turning operations where consistent productivity and predictable wear patterns are required; selection of an appropriate holder and cutting parameters will further enhance life and finish. The construction and coating deliver reliable performance across batch production and single-part runs alike. For secure, high-productivity turning with the Tungaloy T9215 grade, contact Metav Werkzeuge for expert ordering and application advice via info@metav-werkzeuge.com or telephone +49 2822 7131930 Technical data Article number: 6772254 Manufacturer SKU: TUN6772254 SKU: 6772254-Tungaloy Designation: DNMG110404 T9215 Facts Size (inscribed circle): 11 mm Thickness: 4.76 mm Corner radius: 0.4 mm Relief angle: 0° Insert angle: 55° Cutting edges per insert: 2 Special features Material: carbide Coating: CVD Grade: T9215 Geometry: rhombic (DNMG) Chipbreaker: double-sided Hole style: cylindrical locating hole Compatible with: ISO indexable turning systems Application: turning (external and internal) Typical use: medium steel, continuous to light interrupted cuts FAQ What materials is this insert intended for? The DNMG110404 T9215 insert is optimised for medium steel machining; the T9215 grade and CVD coating provide wear resistance and edge security suitable for such applications. How many cutting edges are available per insert? The insert offers two usable cutting edges due to its double-sided design, which reduces tooling costs and changeover frequency. Is the geometry compatible with standard turning holders? Yes — the DNMG form follows ISO conventions; compatibility depends on holder form, relief angle, tolerance class, fastening and size, with this insert matching common 55° rhombic holders. What is the corner radius and how does it affect results? The corner radius is 0.4 mm, which increases edge strength and improves process security while providing a good balance between surface finish and tool life. Does this insert come with a specific mounting requirement? The insert uses a cylindrical locating hole for secure clamping; correct seating and the appropriate clamping kit ensure repeatable performance. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
DNMG 110404 T9215 Wendeplatten - Tungaloy
Take advantage of a CVD-coated carbide grade T9215 for high productivity and a rhombic, double-sided geometry that ensures economical turning in medium steels; order directly via Metav Werkzeuge or consult our technical advisors for application-specific guidance. DNMG110404 T9215 — ISO indexable turning insert for turning by Tungaloy — CVD-coated carbide, 55° geometry The DNMG110404 T9215 is an ISO-standard indexable turning insert designed for general external and internal turning, combining a robust CVD-coated carbide grade with a versatile rhombic form for productive machining of medium steels. DNMG110404 geometry with 55° cutting angle CVD-coated carbide grade T9215 for medium steel Double-sided chipbreaker for versatile cutting Rhombic insert, 0.4 mm corner radius, with hole Higher throughput on medium steels with predictable tool life The combination of a CVD-coated carbide substrate and the T9215 grade provides a balanced mix of wear resistance and fracture toughness, making the insert particularly suitable for sustained production. The coating reduces flank and crater wear under continuous and slightly interrupted cuts, which translates into longer intervals between indexings and fewer tool changes. For users seeking consistent cycle times, the result is measurable productivity gains and reduced process variability, since edge wear progresses predictably under recommended cutting conditions. Secure clamping and wide holder compatibility for stable turning Designed as an ISO-indexable plate, compatibility with the toolholder is determined by the insert’s form, clearance, tolerance class, fastening and thickness. The rhombic 55° geometry and the 0° clearance angle offer flexible approach angles for turning operations, while the cylindrical hole ensures positive seating and repeatable clamping. This mechanical stability reduces vibration and supports better surface finish, so the insert supports both roughing and finishing passes when paired with a suitably rigid holder and correct shim/clamping set. Practical features that simplify selection and process planning With a 0.4 mm corner radius and a plate thickness of 4.76 mm, the geometry balances edge strength and the ability to achieve fine surface finishes. The double-sided chipbreaker is optimised for a range of feeds and depths of cut, reducing the need for multiple specialised grades on the shop floor. For procurement and inventory, the compact specification—size 11, rhombic form—makes it easy to standardise holders and spare parts across several turning stations, lowering indirect costs and streamlining tool logistics. Clear guidance for non-specialists and production planners An indexable insert is a removable cutting plate mounted in a holder; it is not the whole tool. The CVD coating is a thin, hard layer applied by chemical vapour deposition to improve wear resistance at elevated temperatures typical of turning. Choosing the T9215 grade favours a balance between wear life and toughness for steel machining—making it a first choice for medium steel applications where both tool life and edge security matter. For tricky interrupted cuts or highly unstable set-ups, selecting an insert with higher toughness or a different chipbreaker may be advisable. For high-productivity turning choose the Tungaloy DNMG110404 T9215 insert — contact Metav Werkzeuge for tailored recommendations and order support via info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Manufacturer article number: 6966157 SKU (manufacturer): TUN6966157 Model series: ISO indexable turning inserts Material: Carbide Grade/coating: T9215, CVD-coated Facts Cutting angle: 55° Corner radius: 0.4 mm Thickness: 4.76 mm Size: 11 Clearance angle: 0° Hole: with cylindrical hole Special features Rhombic plate form Double-sided chipbreaker Application: Turning (external and internal) Compatibility requires matching holder form, clearance, tolerance class, fastening, size and thickness System components: insert, appropriate external holder or boring bar, shim/clamping set and replacement screws FAQ What materials is this insert best suited for? The DNMG110404 T9215 insert from Tungaloy is optimised for medium steel machining; the CVD-coated carbide grade balances wear resistance and toughness for stable, productive turning. How does the double-sided chipbreaker help in production? A double-sided chipbreaker provides two usable cutting edges and a chip geometry suited to a range of feeds and depths, increasing edge utilisation and reducing inventory variety for serial production. What must be considered when selecting a holder for this insert? Holder selection must match the insert’s form, clearance angle, tolerance class, fastening method, size and thickness to ensure secure clamping and repeatable cutting performance. Is the DNMG110404 suitable for interrupted cuts? The T9215 grade offers good fracture resistance for light to moderate interruptions; for heavy interruptions a tougher grade may be recommended. Which SKU identifies the exact item for ordering? Order using the manufacturer SKU TUN6966157 or article number 6966157 to ensure the correct DNMG110404 T9215 Tungaloy indexable insert is supplied. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
DNMG 110404 T9215 Wendeplatten - Tungaloy
Take advantage of the combination of high wear resistance, stable chip control and straightforward compatibility with ISO tool holders for efficient turning operations; order directly via Metav Werkzeuge or consult the sales engineers for tailored cutting recommendations. DNMG110404 T9215 — DNMG 110404 T9215 indexable turning insert for turning by Tungaloy, CVD-coated carbide, 0.4 mm radius DNMG110404 T9215 is an ISO‑standard indexable insert designed for external and internal turning in medium steels; it delivers reliable life and productivity when matched with the correct holder geometry and chipbreaker. CVD-coated carbide grade T9215 0.4 mm nose radius for precise forms Rhombic form with 55° included angle Double-sided chipbreaker, cylindrical hole Increased productivity with wear-resistant coating The CVD-coated carbide of grade T9215 combines a hard, wear-resistant surface with a tough substrate to support high productivity during continuous and lightly interrupted cuts. This material pairing reduces flank wear and prolongs usable tool life in medium steel applications; as a result, component quality and machine uptime improve. Compatibility with ISO tool holders is determined by form, clearance angle and thickness, ensuring fast integration into existing toolsets without unnecessary adjustments. Consistent geometry for precise turning and easy indexing A rhombic plate form with a 55° included angle and a 0.4 mm radius creates reliable edge geometry for form accuracy and repeatable part finish. The insert’s 0° clearance specification and its cylindrical centre hole provide secure clamping and straightforward indexing of the double-sided design, which helps reduce setup time and simplifies inventory management. The combination of these geometric features supports stable cutting forces and predictable results across batch runs. Practical selection guidance and materials suitability This insert is optimised for medium steel machining; the double-sided chipbreaker offers balanced chip control for a range of feeds and depths of cut. Choose the chipbreaker and grade according to workpiece stability and the intended cutting parameters to get the best balance of surface quality and tool life. The plate thickness of 4.76 mm and size designation (11) mean the insert fits standard holders designed for DNMG 110404 profiles; confirm holder form and tolerance class to ensure correct seating and performance. Contact Metav Werkzeuge for application-specific recommendations on the Tungaloy DNMG110404 T9215 insert and quote SKU 6772211-Tungaloy to confirm compatibility and delivery options Technical Data Article number: 6772211 SKU: 6772211-Tungaloy Manufacturer article number: 6772211 Model series: ISO-Drehwendeschneidplatten Product name: DNMG110404 T9215 Tungaloy-Wendeplatte Facts Corner radius: 0.4 mm Plate thickness: 4.76 mm Plate size: 11 mm Included angle: 55° Clearance angle: 0° ISO code: 110404 Special features CVD-coated carbide (T9215) Rhombic plate form (DNMG) Double-sided chipbreaker Cylindrical centre hole Suitable for turning (external and internal) Designed for medium steel machining FAQ What materials is this insert best suited for? The DNMG110404 T9215 Tungaloy indexable turning insert (SKU 6772211-Tungaloy) is optimised for medium steel; its T9215 CVD-coated carbide balances wear resistance and toughness for productive steel turning. How does the double-sided chipbreaker affect use? A double-sided chipbreaker provides the same effective cutting geometry on both faces, allowing the insert to be indexed and reused; the DNMG110404 T9215 plate benefits from this design for improved economy and consistent chip control. Which holder characteristics must be checked for compatibility? Compatibility depends on holder form, tolerance class, free angle, fastening method, size and plate thickness; confirm these parameters with the tooling specification to ensure correct seating for the DNMG110404 insert. What is the nose radius and how does it influence results? The insert has a 0.4 mm corner radius, which supports fine profile accuracy and a good surface finish while still permitting moderate feed rates for stable turning operations. Is this insert suitable for interrupted cuts? Yes — the T9215 grade combines toughness and wear resistance to perform well in continuous and slightly interrupted cuts common in medium steel turning. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
DNMG 110404 T9215 Wendeplatten - Tungaloy
Take advantage of the combination of CVD-coated carbide and a 0.4 mm corner radius to achieve reliable productivity in medium-steel turning; the rhombic, ISO-standard geometry ensures straightforward holder compatibility. Order the DNMG110404 T9215 insert directly via Metav Werkzeuge or consult our specialists if clarification is needed. DNMG 110404 T9215 — Turning insert by Tungaloy, ISO rhombic, 55° DNMG110404 T9215 is an ISO-standard, rhombic indexable insert designed for general turning tasks in medium steel, offering a balance of wear resistance and fracture toughness. ISO-standard rhombic insert for turning CVD-coated carbide, grade T9215 Double-sided chipbreaker for economy 55° geometry with 0.4 mm corner radius Built for sustained productivity in medium-steel turning The CVD-coated carbide and T9215 grade combine to provide elevated wear resistance alongside good resistance to fracture, making the insert suitable for continuous to lightly interrupted cuts in medium steels. As an ISO-standard part, the component simplifies procurement and stockkeeping while enabling predictable tool life and process control. This results in fewer interruptions, stable cycle times and improved overall machining throughput when the correct holder and clamping are used. Geometry and mounting that improve surface quality and economy A 55° lead angle and a 0° relief angle produce a cutting geometry that supports both finishing and general-purpose turning, while the 0.4 mm corner radius helps achieve consistent surface integrity on turned components. The double-sided chipbreaker allows the insert to be indexed twice, reducing tooling cost per edge. A cylindrical hole provides a secure, repeatable mounting interface with shims and clamping sets, contributing to consistent run-out and part accuracy during operation. Practical integration: selection and system considerations Compatibility with a given holder is determined by form, free angle, tolerance class, fastening, size and thickness; plan the tool system as a whole (insert, matched external holder or boring bar, shim/clamp set and spare screws). Choose the chipbreaker and grade to match workpiece material and cutting conditions: the T9215 grade is a first choice for medium-steel applications where a balance of high productivity and edge security is required. For shops new to indexable tooling, begin with moderate cutting parameters and increase speed or feed once process stability is confirmed. Contact Metav Werkzeuge to specify the optimal Tungaloy T9215 insert for the task and secure consistent productivity — email info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: 6772220-Tungaloy Manufacturer SKU: TUN6772220 Designation: DNMG110404 Data Angle: 55° Corner radius: 0.4 mm Thickness: 4.76 mm Size: 11 mm Special features Material: Carbide Coating: CVD-coated Grade: T9215 Geometry: Rhombic, double-sided Hole: cylindrical hole Relief angle: 0° FAQ What materials is this insert intended for? The DNMG110404 T9215 indexable insert is optimised for medium steel; the CVD-coated T9215 grade is chosen to balance wear resistance and fracture toughness for such materials. Can the insert be used on interrupted cuts? Yes, the T9215 grade is suitable for continuous to lightly interrupted cuts; the combination of CVD coating and carbide substrate helps withstand variable engagement. How does the insert’s geometry affect surface finish? The 55° lead angle and 0.4 mm corner radius support improved surface integrity and dimensional control; correct holder rigidity further enhances the finished surface. Is the insert reversible and economical to use? The double-sided chipbreaker allows two usable edges per insert, which reduces cost per cutting edge and simplifies inventory management when using DNMG110404 inserts. Which components are needed to assemble a working tool system? A matching external holder or boring bar, a shim/clamp set and replacement screws complete the system; compatibility depends on form, free angle, tolerance class, fastening method, size and thickness. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
DNMG 110404 T9225 Wendeplatten - Tungaloy
Take advantage of the combination of robust CVD‑coated carbide, reliable chip control and straightforward holder compatibility to maintain productive turning operations; order via Metav Werkzeuge or consult Metav's technical team for selection advice. DNMG 110404 T9225 DNMG — Turning indexable insert (CVD‑coated carbide, 0.4 mm radius) by Tungaloy A DNMG110404 T9225 indexable insert designed for ISO‑standard turning, suitable for both external and internal machining where medium to heavy steel cutting requires toughness and consistent chip formation ISO rhombic insert DNMG110404, 55° geometry CVD‑coated carbide grade T9225 for steel machining 0.4 mm corner radius for consistent chip control Double-sided chipbreaker with cylindrical hole Dependable performance under mixed cutting conditions The CVD‑coated grade T9225 is a robust, universal carbide developed for medium to heavy steel turning where changing entry conditions or lightly interrupted cuts demand increased toughness. The coating improves high‑temperature wear resistance, reducing flank and crater wear during sustained engagement. As an ISO‑conforming rhombic insert, the component integrates into standard tool systems; compatibility depends on form, relief angle, tolerance class, fixation method, size and thickness, which supports predictable tool behaviour in serial production environments. This specification approach helps stabilise cycle times and reduces unexpected rework by providing a consistent cutting edge and reliable life expectancy. Consistent surface quality with controlled cutting geometry A 0.4 mm corner radius offers a balanced compromise between edge strength and surface finish: the larger radius increases edge robustness during interrupted cuts, while the moderate radius still permits fine surface tolerances where required. The 55° lead angle delivers versatile engagement for facing and profile turning, enabling smooth load distribution across the cutting edge. The insert's double‑sided chipbreaker promotes effective chip segmentation and evacuation, directly contributing to consistent surface results and reduced secondary finishing. These characteristics translate to measurable benefits: steadier process parameters and fewer machining interruptions. Easy integration and procurement for production environments As an ISO indexable insert, fitment is determined by the insert form, relief angle (0° in this case), tolerance class, fastening style and physical dimensions — all of which are standardised to simplify tool selection and inventory management. The cylindrical hole and reversible geometry support economical use, doubling the available cutting edges and simplifying tool change procedures. When pairing the insert with an appropriate holder and clamping set, the system offers repeatable positioning and secure fixation, which is essential in batch production and automated turning centres. For material and chipbreaker selection, match the T9225 grade and chip‑control style to the workpiece stability and feed conditions to maximise productivity and tool life. Contact Metav Werkzeuge for tailored selection of Tungaloy inserts such as the DNMG110404 T9225 and expert advice on the correct grade and chipbreaker for the intended turning application. Technical data Article number: 6780895 SKU: 6780895-Tungaloy Manufacturer SKU: TUN6780895 Model series: ISO turning indexable inserts Facts Inscribed circle: 11 mm Thickness: 4.76 mm Corner radius: 0.4 mm Relief angle: 0° Lead angle: 55° Hole style: cylindrical hole Special features Grade: T9225 (CVD‑coated carbide) Material: carbide Shape: rhombic Double‑sided chipbreaker ISO designation: DNMG110404 Application: turning FAQ Which materials is this insert best suited for? The DNMG110404 T9225 indexable insert is formulated as a universal, tough grade for steel machining, particularly for medium to heavy cuts and situations with variable engagement or light interruptions. What chip control does the insert provide? The insert features a double‑sided chipbreaker with a cylindrical hole, which promotes reliable chip segmentation and evacuation for steady cutting forces and improved surface quality. Is the insert reversible and economical to use? Yes, the reversible geometry yields multiple usable cutting edges per insert, extending service life and reducing tooling costs in high‑volume turning operations. How is compatibility with a toolholder ensured? Compatibility depends on the insert form, relief angle (0°), tolerance class, attachment method, size (11 mm) and thickness (4.76 mm); matching these parameters ensures correct seating and repeatable indexing. What effect does the 0.4 mm corner radius have on machining? A 0.4 mm corner radius increases edge strength for interrupted cuts and contributes to uniform chip formation, while still enabling acceptable surface finishes for many turning tasks. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
DNMG 110404 T9225 Wendeplatten - Tungaloy
Robust CVD-coated carbide construction and ISO compatibility deliver dependable performance for medium-to-heavy steel turning, while the rhombic 55° geometry and 0.4 mm corner radius promote stable chip formation and repeatable surface quality. Order the insert directly via Metav Werkzeuge or consult our technical advisers for tailored cutting data. DNMG110404 T9225 Tungaloy insert — Turning insert (ISO DNMG 110404), rhombic 55° The DNMG110404 T9225 is an ISO-standard rhombic turning insert engineered for medium-to-heavy steel turning, offering a double-sided chipbreaker and a cylindrical hole for secure fastening. CVD-coated carbide grade T9225 ISO DNMG 110404 rhombic 55° geometry Double-sided chipbreaker, cylindrical hole Robust for medium-to-heavy steel turning Consistent productivity through a tougher CVD-coated grade The CVD-coated T9225 grade combines hardness and toughness to withstand slightly interrupted cuts and changing engagement conditions typical in heavy turning operations. This balance extends tool life and reduces index changes, which in turn supports steady production cycles and lower overall machining costs. The coating enhances wear resistance at elevated cutting temperatures, allowing more reliable cycle times under demanding workpiece materials such as medium-to-heavy steel. Operators benefit from fewer insert changes and more predictable tool performance on multi-shift production. ISO-standard geometry for straightforward integration Compatibility is ensured by the ISO designation and precise geometry: DNMG110404 format with a 55° rhombic approach, 11 mm size and 4.76 mm thickness. The 0.4 mm corner radius and a cylindrical hole provide defined seating and clamping for a wide range of external holders and boring bars. Because holder fit depends on form, clearance angle, tolerance class, fastening type, size and thickness, the ISO standard reduces uncertainty when specifying replacements or stocking inserts for diverse turning fixtures. This standardisation streamlines inventory and minimises downtime when inserts are changed. Better chip control and surface quality for fewer reworks The integrated double-sided chipbreaker promotes controlled chip formation and evacuation across a range of cutting conditions, contributing to improved surface finish with reduced manual finishing. The rhombic shape and chipformer geometry help break chips effectively even under variable feed or interrupted cuts, lowering the risk of workpiece damage and machine downtime. For customers seeking consistent batch-to-batch quality, these design features translate into higher first-pass yields and less post-process machining. System thinking: matching insert, holder and process parameters This ISO turning insert is intended for external and internal turning; the cutting system should comprise the insert, a matching outer holder or boring bar, an appropriate shim/clamp and the correct fixing screws. Select the chipbreaker and the T9225 grade according to workpiece material, machining strategy and machine rigidity to gain the full benefit of the insert’s toughness and wear resistance. For process planning, technical advisers can provide recommended speeds, feeds and depths of cut based on machine power and clamping stability, supporting safer, more efficient implementation in production environments. Contact Metav Werkzeuge today for recommended cutting data and to order the Tungaloy DNMG110404 T9225 insert for robust, reliable steel turning — email info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: 6780983 Manufacturer SKU: TUN6780983 SKU: 6780983-Tungaloy Series: ISO turning inserts Cutting material: CVD-coated carbide Grade: T9225 Dimensions / core data Insert designation: DNMG110404 Shape: rhombic 55° Size: 11 mm Thickness: 4.76 mm Corner radius: 0.4 mm Clearance angle: 0° Hole: cylindrical hole Applications / features Application: Turning Chipbreaker: double-sided Typical use: medium-to-heavy steel turning Compatibility note: ISO-standard; holder matching by form, clearance, tolerance, fastening, size and thickness FAQ Which materials is this insert designed for? The DNMG110404 T9225 insert is optimised for medium-to-heavy steel turning; the CVD-coated carbide construction provides wear resistance and toughness for demanding steel machining. What are the key geometry and size details of the insert? The insert follows the DNMG110404 ISO format with a 55° rhombic shape, 11 mm size, 4.76 mm thickness and a 0.4 mm corner radius; it is supplied with a cylindrical hole for fastening. Is the insert reversible and how many cutting edges are available? Yes — the double-sided design provides two indexed cutting edges per side, enabling multiple repositions before replacement and improving cost efficiency per insert. How does the chipbreaker affect machining? The double-sided chipbreaker is designed for stable chip formation across varying cutting conditions, reducing the likelihood of long chips and supporting improved surface quality and process reliability. What should be considered when matching the insert to a holder? Ensure holder compatibility by checking form, clearance angle (0° for this insert), tolerance class, fastening method, size and thickness; correct matching secures seating and repeatable performance. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
DNMG 110404 T9225 Wendeplatten - Tungaloy
Take advantage of the combination of CVD-coated carbide, universal T9225 grade and precise DNMG geometry to ensure stable, productive turning in medium to heavy steel applications; order directly via Metav Werkzeuge or contact the technical team for tailored recommendations. DNMG 110404 T9225 — Rhombic turning insert, CVD-coated carbide by Tungaloy DNMG110404 T9225 is an ISO-conforming turning insert designed for external and internal turning in a wide range of steel machining tasks, offering robustness where variable engagement and interrupted cuts occur CVD-coated carbide for robust performance Universal T9225 grade for medium-heavy steel Rhombic DNMG shape with 55° cutting angle Double-sided chipbreaker, cylindrical hole Proven performance for medium to heavy steel turning The insert is manufactured from carbide with a CVD-coated surface, delivering a balanced combination of wear resistance and toughness. This T9225 grade is formulated for stable chip formation and reliable edge life when machining steels under varying cutting conditions. The rhombic geometry and 55° approach angle contribute to predictable cutting forces and effective chip evacuation, which in turn supports consistent productivity and process stability on turning centres. Designed for system compatibility and secure clamping Compatibility with the toolholder is determined by insert shape, clearance angle, tolerance class, clamping method, size and thickness. The DNMG form with a cylindrical hole allows for common clamping systems and ensures repeatable seating when combined with the appropriate pad and screw set. Operators can select matching holders or boring bars based on the ISO designation and dimensional data to achieve correct seat contact and minimise runout. Why the T9225 grade and CVD coating matter The T9225 grade provides a universal solution for mixed or interrupted cuts, offering additional toughness relative to purely wear-focused grades. The CVD coating enhances surface hardness and thermal resistance, reducing flank wear and extending edge life in elevated cutting temperatures typical of steel turning. For shops seeking fewer insert changes and steady quality, this combination reduces downtime and contributes to overall cost-effectiveness. Practical benefits in the machining cell With a 0.4 mm cutting edge radius and an insert thickness of 4.76 mm, this rhombic DNMG insert is suitable where a compromise between edge strength and profile sharpness is required. The double-sided chipbreaker enables two usable cutting edges per side, improving economy per insert and ensuring efficient chip control. Typical system assembly comprises the insert, an ISO-compatible external holder or boring bar, a pad/clamp set and spare mounting screws to maintain uptime. For reliable medium-to-heavy steel turning with Tungaloy’s T9225 grade, contact Metav Werkzeuge for specific holder recommendations or order support; email info@metav-werkzeuge.com or call +49 2822 7131930 to discuss suitability and availability. Technical Data Article number: 6787106 Manufacturer SKU: TUN6787106 Metav SKU: 6787106-Tungaloy Model series: ISO turning inserts Manufacturer: Tungaloy Facts Cutting edge radius: 0.4 mm Insert thickness: 4.76 mm Insert size: 11 mm Cutting angle: 55° Clearance angle: 0° Special features Grade: T9225, CVD-coated carbide Shape: rhombic DNMG Chipbreaker: double-sided Hole: with cylindrical hole Typical use: external and internal turning Compatibility factors: form, clearance angle, tolerance class, fastening, size and thickness FAQ What materials is this insert best suited for? The insert is optimised for steel machining; the T9225 grade and CVD-coated carbide make it particularly suitable for medium to heavy steel turning and for slightly interrupted cuts. How does the DNMG form affect cutting performance? A rhombic DNMG shape provides a 55° approach that balances cutting force direction and edge strength, offering stable performance for external and internal turning operations. Can this insert be used on both sides? Yes, the insert features a double-sided chipbreaker, providing multiple usable cutting edges and economical edge utilisation when correctly clamped in the compatible holder. Which system components are required for safe clamping? Safe assembly typically includes an ISO-compatible external holder or boring bar, the correct pad/clamp set and replacement screws; compatibility is governed by shape, clearance angle, tolerance class, fastening method, size and thickness. What is the manufacturer SKU and article number for ordering? Ordering can reference Manufacturer SKU TUN6787106 and article number 6787106; the product is listed as DNMG110404 T9225 Tungaloy insert. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
DNMG 110404 T9225 Wendeplatten - Tungaloy
Combining a CVD-coated carbide T9225 grade with a 0.4 mm nose radius and an ISO 55° rhombic form, this insert delivers robust performance for medium to heavy steel turning while coping well with lightly interrupted cuts; order directly via Metav Werkzeuge or consult our specialists for holder compatibility. DNMG 110404 T9225 turning insert by Tungaloy – CVD-coated carbide, 55° rhombic The DNMG110404 T9225 is an ISO-standard rhombic turning insert engineered for medium to heavy steel machining, offering a robust universal grade and a double-sided chipbreaker for flexible cutting directions. ISO rhombic insert DNMG 110404 CVD-coated carbide grade T9225 0.4 mm nose radius for precise profiles Double-sided chipbreaker, cylindrical hole Consistent performance under variable cutting conditions The combination of a CVD-coated carbide substrate and the T9225 grade provides a balance of toughness and wear resistance that suits changing engagement conditions. This makes the insert particularly effective when cuts are lightly interrupted or when stability varies, reducing the frequency of insert changes and contributing to steady cycle times. The double-sided chipbreaker improves chip control in both turning directions, which helps to protect the cutting edge and maintain consistent surface quality on workpieces made primarily from steel. The result is a reliable production process with predictable tool behaviour. Precise profile control and surface quality A 0.4 mm nose radius and the 55° rhombic shape deliver accurate contouring and repeatable profiles on external and internal turning tasks. The modest nose radius supports fine detail work while retaining sufficient edge strength for heavier passes, so component tolerances are held without excessive tool wear. The insert’s geometry and CVD coating together support a balanced cutting action that aids in achieving even surface finishes and consistent dimensional results across batches, reducing rework and inspection efforts. Straightforward integration with ISO tool systems Designed to the ISO plate standard, this insert is compatible where holder form, clearance angle, tolerance class, clamping method, size and thickness match. The system concept includes the plate, a matching external holder or boring bar, a shim/clamp set and replacement screws, simplifying procurement and assembly in established turning centres. The with cylindrical hole feature eases accurate seating and clamping, improving positional repeatability and minimising vibration that can affect tool life and part quality. Selection guidance and application advantages Choose the robust universal grade when working with varied steel alloys or when occasional interruptions occur; the T9225 grade is intended for medium to heavy steel machining and provides enhanced toughness compared with more wear-optimised grades. Selecting the appropriate chipbreaker and ensuring the holder matches the plate’s 11 mm inscribed circle and 4.76 mm thickness will maximise performance. Where higher cutting speeds or specialised materials are required, consider alternative grades; otherwise, this insert offers a pragmatic mix of longevity, process security and simplified tool management. For tailored advice on Tungaloy turning inserts such as the DNMG110404 T9225 and to confirm holder compatibility, contact Metav Werkzeuge by phone +49 2822 7131930 or email info@metav-werkzeuge.com Technical data Article number: 6780625 Manufacturer SKU: TUN6780625 SKU: 6780625-Tungaloy Model series: ISO-Drehwendeschneidplatten Designation: DNMG110404 (110404) Grade: T9225 Material: carbide Facts Nose radius: 0.4 mm Included angle: 55° Free clearance angle: 0° Thickness: 4.76 mm Inscribed circle: 11 mm Hole: with cylindrical hole Chipbreaker: double-sided Special features CVD-coated carbide grade T9225 Robust universal grade for medium to heavy steel turning Rhombic plate form, 55° cutting angle Double-sided chipbreaker for flexible cutting directions Compatible with ISO holders defined by form, clearance angle and clamping System composition: insert, external holder or boring bar, shim/clamp and replacement screws Application: Turning FAQ What materials is this insert intended for? The DNMG110404 T9225 insert is engineered primarily for medium to heavy steel machining and is optimised for applications where toughness and reliable chip control are required. Is the plate reversible and suitable for both turning directions? Yes, the plate features a double-sided chipbreaker and a symmetrical rhombic geometry that permit use in both cutting directions with consistent chip formation. How is the insert secured in the holder? The insert is mounted using the standard ISO clamping method: locating with the cylindrical hole and securing with the appropriate screw, shim or clamp as specified for the matching holder. What does the T9225 grade signify? T9225 denotes a CVD-coated carbide grade designed as a robust universal solution for steel turning, offering a compromise between wear resistance and fracture toughness to cope with variable cut conditions. Which holder characteristics must be matched to ensure compatibility? Compatibility depends on holder form, clearance (facing) angle, tolerance class, clamping design, insert size and thickness; matching these parameters ensures correct seating and repeatable performance. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
DNMG 110404 T9225 Wendeplatten - Tungaloy
Combining a robust CVD-coated carbide T9225 grade with a precise rhombic geometry delivers consistent performance in medium to heavy turning operations; the double-sided chipbreaker and standard ISO form make the insert an economical choice for mixed batch production. Order the DNMG110404 directly via Metav Werkzeuge or request application advice from our consultants for an optimised tool assembly. DNMG110404 T9225 — ISO turning insert by Tungaloy, 55° lead angle The DNMG110404 T9225 is an ISO rhombic indexable insert intended for turning operations, engineered as a CVD-coated carbide grade for robust, reliable cutting in varying engagement conditions Robust CVD-coated carbide grade T9225 Double-sided chipbreaker for versatility Rhombic 11 size with 55° lead angle Cylindrical hole compatible with ISO holders Consistent cutting performance for changing conditions The combination of a CVD-coated surface and a carbide substrate gives a stable cutting edge that tolerates slight interruptions and variable chip loads. The T9225 grade is formulated for mid to heavy steel machining where occasional tough spots or interrupted cuts occur; this means fewer unexpected tool changes and a more predictable cycle time. By favouring a tougher grade over a highly wear-resistant but brittle option, the insert offers an improved margin against chipping during unstable cutting, which supports continuous productivity in mixed-production environments. Geometry that supports precision and repeatability A rhombic profile with an 11-size designation and a 55° lead angle provides a balanced contact geometry that reduces cutting forces while maintaining dimensional control. The 0.4 mm corner radius contributes to a consistent surface finish without sacrificing edge strength, and the 4.76 mm plate thickness increases rigidity in the clamped assembly. These geometric choices help deliver repeatable results on external and internal turning tasks, enabling stable tool life and predictable part tolerances in serial or single-piece manufacturing. Simplified tool setup and wide holder compatibility The insert follows ISO standards, so compatibility with holders depends on form, relief angle, tolerance class, fixing method, size and thickness; this standardisation eases tool selection and inventory management. The cylindrical hole and double-sided format allow economical indexing: two usable edges per side and a straightforward clamping scheme reduce downtime and spare-part complexity. Where process security and quick changeover matter, the standardised form and mounting give planners and operators clear guidance for matching insert, holder and machine dynamics. Practical benefits for production planning Selecting this grade reduces the number of specialised items required in a tooling cabinet, thanks to its universal orientation for a broad range of steels. The combination of T9225 robustness and the rhombic geometry supports both roughing and light finishing passes when parameters are adapted, which can shorten the time to first good part. In addition, the CVD coating improves resistance to built-up edge and thermal wear during sustained cuts, safeguarding machining quality across varying batch sizes. For tailored cutting data, holder recommendations or to secure genuine Tungaloy DNMG110404 T9225 inserts, contact Metav Werkzeuge for technical consultation at info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: 6966159 SKU: 6966159-Tungaloy Manufacturer SKU: TUN6966159 Model designation: DNMG110404 Label: DNMG110404 T9225 Tungaloy insert Core specifications Corner radius: 0.4 mm Insert size: 11 mm Thickness: 4.76 mm Lead angle: 55° Relief angle: 0° Hole style: cylindrical Design & special features Shape: rhombic Chipbreaker: double-sided Material: carbide Coating: CVD, grade T9225 Application: turning Series: ISO turning inserts Mounting: with hole FAQ What materials is this insert optimised for? The Tungaloy DNMG110404 T9225 insert is optimised for medium to heavy steel machining, offering toughness and stable chip formation for mixed cutting conditions. Can the insert be indexed for multiple cutting edges? Yes, the insert is double-sided with a central cylindrical hole, allowing indexing and economical use of several cutting edges before disposal. Which holder types are compatible with this ISO insert? Compatibility depends on matching the ISO form, relief angle, tolerance class, fastening and thickness; the DNMG110404 form fits standard ISO-compatible turning holders designed for rhombic inserts. How does the CVD coating affect tool life and finish? The CVD-coated carbide of grade T9225 enhances thermal and abrasive resistance, reducing built-up edge and helping to preserve edge integrity, which supports consistent surface finish over longer cycles. Is this insert suited to interrupted cuts or unstable conditions? Yes, the T9225 grade is formulated for tougher engagement and performs well where marginally interrupted cuts or variable loads occur; its toughness reduces chipping risk. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
DNMG 110404 T9225 Wendeplatten - Tungaloy
Take advantage of the CVD‑coated carbide T9225 for improved tool life and stable chip control together with the ISO DNMG110404 profile for consistent mid‑to‑heavy steel turning; order directly via Metav Werkzeuge or consult our technical advisors for application support. DNMG110404 T9225 indexable turning insert by Tungaloy — CVD‑coated carbide, 55° rhombic The DNMG110404 T9225 is an ISO‑standard rhombic, double‑sided indexable insert designed for external and internal turning in steel CVD‑coated carbide grade T9225 Robust universal grade for steel Double‑sided with cylindrical hole 55° rhombic geometry, 0.4 mm corner Reliable cutting performance for medium‑to‑heavy turning The CVD‑coated carbide grade provides a balanced combination of toughness and wear resistance that supports steady machining under variable engagement conditions. Designed as a robust universal grade, the insert ensures consistent cutting edge life and reduced unscheduled tool changes, which helps to maintain production flow and lower overall tooling costs. The coating improves resistance against built‑up edge and abrasive wear, translating into longer service intervals on steel components. Secure clamping and straightforward integration into ISO systems Compatibility follows ISO standards: holder selection depends on form, clearance angle, tolerance class, fastening type, size and thickness. The rhombic geometry with a cylindrical hole and precise dimensions facilitates reliable clamping and repeatable positioning in standard DNMG carriers. This standardisation simplifies tool inventory management and supports fast tool changes on the shop floor, reducing machine downtime and improving throughput. Improved chip control and surface quality Equipped with a double‑sided chipbreaker, the insert promotes controlled chip formation and evacuation, lowering the risk of entanglement and secondary machining marks. Stable chip control reduces vibration and enables better surface finish in both external and internal turning operations. The combination of grade and chipbreaker is particularly effective when cutting under slightly interrupted conditions or where variable forces demand additional toughness. Application scope and practical advantages for production Specifically intended for turning steel, the geometry and grade perform well in mid‑to‑heavy cutting applications where a balance of wear resistance and fracture toughness is required. The insert is suited to a wide range of turning tasks, from continuous finish passes to more demanding roughing cuts. Its double‑sided design delivers economical indexability, while the ISO designation and standard dimensions ensure broad compatibility with existing toolholders. For reliable mid‑to‑heavy steel turning with Tungaloy's T9225 grade, contact Metav Werkzeuge to request the DNMG110404 insert (SKU TUN6780643) or to discuss application‑specific recommendations with our consultants Technical data Article number: 6780643 Manufacturer SKU: TUN6780643 Model series: ISO turning indexable inserts Material: Carbide Grade: T9225 ISO designation: DNMG110404 Facts Size: 11 mm Thickness: 4.76 mm Corner radius: 0.4 mm Relief angle: 0° Insert angle: 55° Hole: cylindrical hole Special features CVD‑coated carbide Double‑sided chipbreaker Rhombic plate form Double‑sided indexability Suitable for external and internal turning Robust universal grade for medium‑to‑heavy steel machining Compatible with ISO holders (form, clearance angle, tolerance class, fastening, size, thickness) FAQ Which materials is this insert suitable for? The DNMG110404 T9225 insert is specified for steel machining; the T9225 CVD‑coated carbide grade is designed for robust, mid‑to‑heavy steel applications where toughness and wear resistance are required. Is the insert compatible with standard DNMG holders? Yes. The insert follows ISO designation DNMG110404; compatibility with a holder is determined by holder form, relief (clearance) angle, tolerance class, fastening method, size and plate thickness. What chip control and coating does the insert offer? The insert features a double‑sided chipbreaker and a CVD‑coated carbÂide grade T9225 for improved chip formation and enhanced wear resistance. What are the key dimensions to check before fitting? Important dimensions include the 11 mm size, 4.76 mm thickness, 0.4 mm corner radius and the 55° insert angle; the plate also has a cylindrical hole for secure clamping. Manufacturer/Responsible: Tungaloy‑NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand‑new product from the manufacturer.
DNMG 110404 T9225 Wendeplatten - Tungaloy
Take advantage of the combination of a CVD-coated carbide grade for enhanced toughness and a precise 55° rhombic geometry with a 0.4 mm nose radius to secure consistent performance in medium to heavy steel turning; order directly via Metav Werkzeuge or consult the technical advisers for application matching. DNMG 110404 T9225 – Indexable turning insert by Tungaloy (CVD-coated carbide, 55°) A DNMG 110404 T9225 indexable turning insert engineered for medium to heavy steel turning, offering robust cutting performance and reliable chip control for interrupted or variable cutting conditions DNMG 110404 geometry, 55° rhombic CVD-coated carbide grade T9225 0.4 mm nose radius for stable cuts Double-sided chipbreaker, cylindrical hole Consistent cutting in mixed and interrupted steel applications The CVD-coated carbide formulation of the T9225 grade is developed to combine wear resistance with increased fracture toughness, making it suitable for the demands of medium to heavy steel machining. This balance reduces the risk of premature edge chipping when cutting under varying depths of cut or with slight interruptions. As a result, the insert delivers more predictable tool life and fewer unscheduled indexings, which supports steady production flow and lower overall tooling costs. Predictable chip formation and surface quality The double-sided chipbreaker design improves chip control across a range of feeds and depths, producing compact chips that evacuate reliably and reduce the risk of surface marks. Improved chip control contributes to a stable cutting zone, helping attain consistent surface finish values and reducing the need for rework. In practical terms, this means fewer machine stoppages for chip clearance and a reduced likelihood of tool-induced workpiece damage during longer runs. Geometry and clamping compatibility for secure performance The rhombic 55° shape, combined with a 0.4 mm nose radius and a 0° clearance angle, offers a versatile geometry for turning profiles and light shoulder work. The ISO designation ensures compatibility with standard holders; clamping depends on form, tolerance class, fixing method, size and thickness. The insert’s cylindrical hole and standard dimensions simplify secure seating and repeatable positioning in approved toolholders, supporting consistent cutting engagement and dimensional repeatability. Simple integration, reduced tooling costs Being double-sided and indexed, the insert allows two effective cutting edges per side, increasing the number of re-uses before disposal and improving cost efficiency in batch and job shop environments. The indexable insert format and ISO standardisation make it straightforward to replace or restock without extensive holder changes. For operations that switch between jobs or materials, the robust grade reduces tool-change frequency while maintaining stable edge life and predictable results. For application guidance or to specify the right DNMG insert for particular steel grades, contact Metav Werkzeuge for expert advice and rapid delivery. Technical Data Article number: 6944643 Manufacturer SKU: TUN6944643 SKU: 6944643-Tungaloy Model series: ISO turning indexable inserts Core dimensions Insert designation: DNMG 110404 Size: 11 mm Thickness: 4.76 mm Nose radius: 0.4 mm Clearance angle: 0° Geometry angle: 55° Hole: with cylindrical hole Materials and features Material: carbide Grade/coating: T9225 (CVD-coated) Chipbreaker: double-sided Insert shape: rhombic Typical application: turning (external and internal) FAQ What steels is this insert best suited to? The DNMG 110404 T9225 insert is optimised for medium to heavy steel machining; the CVD-coated T9225 grade offers increased toughness for variable cutting conditions. How does the chipbreaker affect production stability? The double-sided chipbreaker on this indexable insert promotes compact chip formation and reliable evacuation, which reduces interruptions and helps maintain consistent surface quality. Is the insert compatible with standard ISO holders? Yes, the insert follows ISO geometry standards; compatibility depends on holder form, clearance, tolerance class, fixing method, size and thickness for secure clamping. Can the insert be used for interrupted cuts? The robust carbide and tougher T9225 formulation are designed to withstand light interruptions and variable engagement, improving edge life under such conditions. What are the identifying numbers to order this item? Order using Article number 6944643 or Manufacturer SKU TUN6944643 for the DNMG 110404 T9225 indexable turning insert. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
DNMG 110404 T9225 Wendeplatten - Tungaloy
Take advantage of the combination of robust CVD-coated carbide, a 55° rhombic geometry and a double-sided chipbreaker for consistent medium-to-heavy steel turning — suitable for variable engagement conditions. Order the insert directly via Metav Werkzeuge or contact our consultants for compatibility and cutting-data assistance. DNMG110404 T9225 Tungaloy indexable insert for turning (rhombic 55°, CVD-coated carbide) The DNMG110404 T9225 is an ISO rhombic indexable insert optimised for external and internal turning of steel, offering a 55° lead angle and a double-sided chipbreaker for flexible machining under mixed cutting conditions. ISO rhombic 55° geometry CVD-coated carbide grade T9225 Double-sided chipbreaker Cylindrical mounting hole Reliable performance under changing cutting conditions The insert is engineered as a robust universal grade for the mid-to-heavy machining of steel, combining a CVD coating with a tough cemented carbide substrate. This construction increases resistance to flank wear while preserving edge stability when intermittent cuts or variable immersion occur. The rhombic 55° geometry and 0.4 mm corner radius balance cutting strength and surface finish, enabling predictable tool life and fewer insert changes during production. Simple integration and secure clamping for consistent results Designed to the ISO series for turning inserts, the component integrates with standard DNMG holders; compatibility is determined by insert form, relief angle, tolerance class, fastening method, size and thickness. The cylindrical hole and standard dimensions (11 mm inscribed circle, 4.76 mm thickness) ensure repeatable seating and stable clamping, reducing vibration and improving dimensional consistency across batches. Clear mechanical fitment reduces setup time and supports efficient tool management. Material range, chip control and economic machining The double-sided chipbreaker provides controlled swarf evacuation across common steel alloys and supports both roughing and finishing passes when matched with appropriate feeds and speeds. The grade T9225, a CVD-coated hardmetal, is aimed at productive machining with emphasis on stable chip formation and extended edge life under moderately heavy cutting. For operations seeking cost-effective throughput, this combination contributes to lower tooling frequency and predictable process outcomes. For application-specific cutting data or to confirm holder compatibility for the Tungaloy DNMG110404 T9225, contact Metav Werkzeuge for tailored advice and rapid delivery. Technical data Article number: 6780619 Manufacturer SKU: TUN6780619 Label: DNMG110404 T9225 Tungaloy-Wendeplatte Facts Geometry angle: 55° Corner radius: 0.4 mm Thickness: 4.76 mm Inscribed circle: 11 mm Special features Material: cemented carbide Coating: CVD Mounting: with cylindrical hole Plate form: rhombic (DNMG) Relief angle: 0° Chipbreaker: double-sided Model series: ISO indexable turning inserts Typical application: external and internal turning of steel FAQ What materials is this insert suited for? The insert is intended primarily for medium-to-heavy steel turning; the T9225 grade and CVD coating support stable performance on a wide range of steels. How does the DNMG110404 geometry affect cutting? The 55° rhombic geometry gives a controlled cutting direction and good edge support; the 0.4 mm corner radius helps combine strength with surface quality in turning operations. Is the insert reversible or single-use? The component features a double-sided chipbreaker, allowing the insert to be indexed to a fresh cutting edge, extending usable life before disposal. What should be checked for holder compatibility? Compatibility depends on insert form, relief angle, tolerance class, fastening type, size and thickness; confirm the holder matches the DNMG110404 profile and mounting hole style. Can this insert handle interrupted cuts? Yes — the T9225 grade is formulated for robustness and improved toughness, making it appropriate for varying engagement and light interruptions. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
DNMG 110404 T9225 Wendeplatten - Tungaloy
Benefit from a robust combination of CVD-coated carbide, T9225 universal grade and a 55° rhombic geometry for stable medium-to-heavy turning with reliable chip control; order the insert directly via Metav Werkzeuge or consult our specialists for application-specific advice. DNMG110404 T9225 turning insert (ISO 110404) — Tungaloy A DNMG110404 T9225 ISO-standard turning insert designed for medium to heavy steel turning, featuring a rhombic 55° geometry and a double-sided chipbreaker for varied cutting conditions CVD-coated carbide for robust cutting Universal T9225 grade for variable conditions Rhombic 55° geometry for versatile turning Double-sided insert with cylindrical hole Reliable cutting performance for disrupted cuts and mixed materials The combination of CVD-coated carbide and the T9225 grade delivers a balance of hardness and toughness specifically tailored for medium to heavy steel turning. This material pairing improves wear resistance and extends tool life under variable engagement, while the universal grade resists chipping during light interruptions or changing cut depths. The result is fewer tool changes and a steadier production flow with consistent cycle times. Clear guidance on holder compatibility and application choices Being part of the ISO indexable insert family, compatibility with a toolholder depends on form, clearance angle, tolerance class, clamping method, size and thickness. The rhombic 55° shape and 0° clearance require appropriate holder geometry; the insert’s double-sided chipbreaker supports both external and internal turning when the correct chipformer and grade are selected. This structured approach reduces setup iterations and supports predictable machining results. Process stability and surface quality for productive turning A controlled chip formation from the double-sided breaker combined with the universal carbide grade enhances process reliability and contributes to a consistent surface finish on steel workpieces. The robust substrate reduces flank wear under moderate to heavy cuts, supporting longer tool life and lower tooling costs per part. Where repeatability and uptime matter, this insert assists in maintaining throughput and lowering scrap rates. For tailored cutting data, holder selection and to secure DNMG110404 T9225 inserts for upcoming turning operations, contact Metav Werkzeuge at info@metav-werkzeuge.com or call +49 2822 7131930 to speak with an application consultant Technical data Article number: 6966133 Manufacturer SKU: TUN6966133 SKU: 6966133-Tungaloy Model series: ISO indexable turning inserts Key dimensions Insert size: 11 mm Thickness: 4.76 mm Included angle: 55° Corner radius: 0.4 mm Clearance angle: 0° Features / application Material: carbide Coating / grade: T9225 (CVD-coated) Chipbreaker: double-sided Hole style: cylindrical hole Plate form: rhombic Intended use: turning (external and internal) Compatibility notes: depends on ISO form, tolerance class, clamping, size and thickness FAQ What workpiece materials is this insert suited for? The DNMG110404 T9225 insert is intended primarily for steel machining in medium to heavy applications, where its T9225 grade provides the necessary toughness for variable engagement. Can the insert be used for interrupted cuts? Yes, the CVD-coated carbide and universal T9225 grade are designed to tolerate lightly interrupted cuts and changing cutting conditions without premature chipping. How does the chipbreaker affect performance? The double-sided chipbreaker improves chip control for many turning operations, leading to safer swarf handling and more consistent surface finish when used with the correct toolholder. Which holders are compatible with this ISO insert? Compatibility depends on the ISO form, clearance angle, tolerance class, clamping method, size and thickness; verify holder geometry matches the DNMG110404 dimensions before assembly. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
Fragen zu diesen Produkten??
Mit mehr als 30 Jahren Erfahrung beraten wir Sie gerne persönlich.
Tel.: +49 2822 7131930
Mail: info@metav-werkzeuge.com