DNMG 110408 T9235 Wendeplatten - Tungaloy
Take advantage of the combination of a tough CVD-coated carbide grade, a 55° rhombic geometry and a secure cylindrical-clamp hole to keep turning processes productive even under interrupted cuts; order the insert directly via Metav Werkzeuge or consult our specialists for application advice. DNMG110408 T9235 — DNMG turning insert by Tungaloy, 55° rhombic The DNMG110408 T9235 is an ISO rhombic, double-sided indexable insert designed for external and internal turning, offering a robust solution where interrupted cuts and unstable setups demand higher toughness. CVD-coated carbide grade T9235 ISO DNMG 110408 rhombic insert Double-sided chipbreaker for economy Cylindrical hole for secure clamping Durable grade for unstable and interrupted turning The CVD-coated carbide composition of the insert, specified as T9235, delivers increased toughness that reduces edge chipping in interrupted cuts and under unstable conditions. This translates into a measurable improvement in process reliability: the tougher substrate tolerates more shock without catastrophic edge failure, while the coating provides enhanced wear resistance and lower friction at the cutting zone. For operations in steel where cutting speed is conservative but stability is limited, the grading and coating combination supports longer effective tool life and steadier production. Geometry that balances versatility and secure clamping The rhombic plate form with a 55° cutting angle and a 0.8 mm corner radius offers a balance between strength at the cutting edge and surface finish capabilities; smaller radii favour finer finishes while contributing to lower cutting forces. The insert is double-sided, enabling economical index changes, and features a cylindrical hole for positive, repeatable clamping. As an ISO-form insert, compatibility with suitable external holders is determined by form, tolerance class, fastening method, size and thickness, which ensures predictable interchangeability across standard toolholder systems. Practical guidance for application and optimisation Intended primarily for turning of steel under less aggressive cutting speeds, the insert’s design promotes reliable chip control when matched with the correct chipbreaker and process parameters. The double-sided chipbreaker supports two usable cutting edges per index, reducing tooling costs per finished part. Selection of the precise chipbreaker variant and cutting data should follow the material grade, workpiece rigidity and machining stability; in marginal setups, favour lower feeds and conservative depths of cut to exploit the grade’s shock resistance while maintaining consistent surface quality. For assembly, use the compatible clamping set, underlay and replacement screws specified for ISO DNMG formats. Contact Metav Werkzeuge to discuss how the Tungaloy T9235 DNMG110408 can be integrated into existing turning processes and to check current availability; eMail: info@metav-werkzeuge.com or Phone: +49 2822 7131930 Technical Data Article number: 6785860 Manufacturer SKU: TUN6785860 SKU: 6785860-Tungaloy Model series: ISO-Drehwendeschneidplatten Manufacturer: Tungaloy Facts Corner radius: 0.8 mm Cutting angle: 55° Thickness: 4.76 mm Size: 11 mm Clearance angle: 0° Special features CVD-coated carbide grade T9235 Double-sided chipbreaker Rhombic plate form (DNMG) Cylindrical hole (with hole) ISO designation DNMG110408 Application: Turning FAQ Which materials is this insert best suited for? The Tungaloy DNMG110408 T9235 insert is formulated primarily for machining steel; the T9235 grade provides toughness suitable for unstable conditions and interrupted cuts in steel applications. Can the insert be used for both external and internal turning? Yes, the ISO rhombic geometry and the cylindrical clamping hole make the insert suitable for both external and internal turning when used with the correct holder and mounting accessories. How does the corner radius affect surface finish and strength? A 0.8 mm corner radius gives a compromise between edge strength and surface finish; it improves edge robustness for semi-finishing operations while still allowing acceptable surface quality at typical turning feeds. Is the DNMG110408 compatible with standard DNMG toolholders? The DNMG110408 conforms to ISO geometry, so compatibility depends on matching the insert form, clearance angle, tolerance class, fastening and thickness to the holder specifications. Are both sides of the insert usable? Yes, the insert is double-sided, offering multiple cutting edges per plate to improve cost-efficiency and reduce changeover frequency. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
DNMG 110412 AH120 Wendeplatten - Tungaloy
Take advantage of the combination of PVD-coated AH120 carbide, ISO DNMG110412 geometry and a 1.2 mm corner radius for dependable turning performance and consistent process security. Order the insert directly via Metav Werkzeuge or consult our technical advisers for application-specific guidance. DNMG110412 AH120 indexable turning insert — PVD-coated carbide, rhombic 55° by Tungaloy DNMG110412 AH120 is an ISO rhombic indexable turning insert designed for external and internal turning in ISO tool systems PVD-coated carbide grade AH120 Rhombic ISO DNMG form, 55° included angle 1.2 mm corner radius for precise finishes Double-sided chipbreaker with central cylindrical hole Consistent cutting performance for demanding turning tasks The PVD-coated carbide grade AH120 provides a combination of wear resistance and a sharp cutting edge that supports stable cutting processes. PVD coating improves resistance to abrasion and adhesion at elevated temperatures; in practice this means longer edge life and fewer interruptions for index changes. As an ISO-design insert, the component supplies a reproducible cutting geometry that helps maintain part tolerances and surface quality over long production runs. The result is predictable tool life and higher throughput in repeat operations. Seamless integration into ISO holders and clamping systems Compatibility with toolholders depends on the insert’s form, relief angle, tolerance class, fastening method, size and thickness. The DNMG110412 format with a 55° included angle and a 0° relief angle suits a wide range of external holders and boring bars. The central cylindrical hole provides positive location and secure fastening with standard screws and clamp sets, enabling reliable clamping even under interrupted cuts. Integrating this indexable insert into an established tool system reduces setup times and simplifies requalification of fixtures. Reliable chip control and practical application guidance The double-sided chipbreaker design supports controlled chip formation for a variety of turning conditions, making the insert appropriate where consistent chips and process security are required. The 1.2 mm corner radius balances edge strength and surface finish: larger radii increase robustness, while smaller radii can improve detail and contour fidelity. For best results, pair the insert with a rigid holder, select a chipbreaker and grade suited to the workpiece material and machining stability, and monitor feed and speed to match the application’s heat generation and vibration characteristics. The machining system typically comprises the ISO insert, a matching external holder or boring bar, a support/clamping set and replacement screws. Discuss application requirements with Metav Werkzeuge to specify Tungaloy DNMG110412 AH120 inserts or to request tailored cutting data; contact info@metav-werkzeuge.com or call +49 2822 7131930 for technical guidance Technical data Article number: 6793707 Manufacturer SKU: TUN6793707 SKU: 6793707-Tungaloy Model series: ISO-Drehwendeschneidplatten Material: Carbide Coating: PVD ISO designation: DNMG110412 Core specifications Size: 11 mm Thickness: 4.76 mm Corner radius: 1.2 mm Included angle: 55° Relief angle: 0° Hole: cylindrical Special features Grade: AH120 Chipbreaker: double-sided Shape: rhombic Application: Turning System components: insert, external holder/boring bar, clamp set, spare screws FAQ Which materials is this insert intended for? The DNMG110412 AH120 insert from Tungaloy is a PVD-coated carbide grade formulated for turning applications; it is described as wear- and fracture-resistant and is selected where a sharp cutting edge and process security are required. How is compatibility with a toolholder determined? Compatibility depends on the insert form, relief angle, tolerance class, fastening method, size and thickness; matching these parameters to a toolholder ensures correct seating and clamping of the DNMG110412 geometry. What chip control can be expected from this insert? The double-sided chipbreaker on the AH120 grade promotes consistent chip formation across typical turning conditions; selecting the correct chipbreaker and machining parameters helps to maintain stable chips and minimise secondary operations. Is the insert indexable and how is it clamped? The DNMG110412 is an indexable insert featuring a central cylindrical hole for secure fastening; indexing and reorientation are performed according to the holder and clamping system used. What does the complete machining system include? A complete system for this insert normally comprises the ISO insert itself, a matching external holder or boring bar, an underlay/clamp set and replacement screws to ensure secure mounting and repeatable positioning. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
DNMG 110412 AH120 Wendeplatten - Tungaloy
Take advantage of a combination of PVD-coated carbide hardness and a sharp cutting edge to ensure consistent, low-wear turning operations; the 55° rhomboid geometry and double-sided chipbreaker support predictable chip control and efficient indexing. Order directly via Metav Werkzeuge or consult our team for compatibility and holder selection. DNMG110412 AH120 Tungaloy turning insert — PVD-coated carbide, 55° geometry DNMG110412 AH120 is an ISO-format indexable insert engineered for external and internal turning where a sharp edge and process security are required PVD-coated carbide for wear resistance 55° rhomboid geometry for versatile turning Double-sided chipbreaker for stable chip control Corner radius 1.2 mm for balanced edge strength Consistent cutting performance through PVD-coated carbide The AH120 grade combines a PVD coating with a robust carbide substrate to deliver a wear- and chipping-resistant cutting edge. This construction extends tool life under demanding turning conditions and supports stable dimensional results across batches. The coating reduces adhesive wear and improves heat resistance, which means fewer interruptions for insert changes and a lower frequency of unplanned machine stops. Such material and surface treatment choices generate reliable tool life and steady performance even when sharp edge integrity is essential for the process. Precision geometry that eases tool selection and fitment The insert follows the ISO DNMG format with a 55° rhomboid profile and a corner radius 1.2 mm, combining profile control with edge strength. A 4.76 mm thickness and rhomboid shape provide a predictable engagement with matching holders, while the cylindrical hole ensures secure fastening with compatible clamps and screws. Compatibility to a holder is determined by form, clearance angle, tolerance class, fastening method, size and thickness; these parameters should be checked against the intended external holder or boring bar to ensure correct seating and repeatability. Correct match-up reduces vibration and supports consistent surface quality. Productivity gains from controlled chip flow and indexing Equipped with a double-sided chipbreaker, the insert affords two usable orientations that help extend the in-process life before indexing is required. The chipbreaker geometry promotes stable chip formation and evacuation, lowering the risk of entanglement and toolmarking on the workpiece. Together with the sharp cutting edge quality of the AH120 grade, this results in shorter cycle times and improved first-time-right ratios for turning tasks. As part of a complete system—indexable insert, appropriate external holder or boring bar, and the correct shim/clamp and replacement screws—this insert supports efficient changeovers and reproducible machining. Practical notes on application and handling Designed specifically for turning, the indexable component is suitable where a balance between sharpness and process security is required. The insert is manufactured to ISO tolerances that aid quick substitution and consistent clamping. When replacing or fitting, verify holder geometry and fastening specification; using the correct clamp set and replacement screws maintains seating stability and repeatability. The physical dimensions and hole style simplify inventory management for workshops standardising on ISO-form inserts. Contact Metav Werkzeuge for tailored advice on the Tungaloy DNMG110412 AH120 insert and to confirm holder compatibility or replacement parts Technical Data Article number: 6793704 Manufacturer SKU: TUN6793704 Model series: ISO indexable turning inserts Material: carbide Type designation: DNMG110412 AH120 Label: DNMG110412 AH120 Tungaloy insert Facts Thickness: 4.76 mm Cutting edge angle: 55° Corner radius: 1.2 mm Size: 11 mm Free (clearance) angle: 0° Special features Coating: PVD-coated Chipbreaker: double-sided Plate form: rhomboid Hole style: cylindrical hole (with hole) Typical application: turning (external and internal) System components: insert, matching external holder or boring bar, shim/clip and replacement screws FAQ What materials is this insert intended for? The AH120 grade insert is designed for turning applications where a sharp cutting edge and process security are required; the DNMG110412 AH120 insert performs well across typical turning tasks that demand wear and chipping resistance. How many usable edges does the insert provide? The DNMG110412 AH120 indexable insert features a double-sided chipbreaker, offering multiple usable orientations before indexing or replacement is required. What dimensions are critical when matching a holder? Key dimensions are the 55° geometry, 4.76 mm thickness, 11 mm size and the free angle; these determine fit and seating with the chosen external holder or boring bar when using the DNMG110412 AH120. Does the insert require a special fastening arrangement? The insert uses a cylindrical hole for secure fastening; compatibility depends on the holder’s clamp or screw system and adherence to the ISO tolerance class for the DNMG110412 format. How does the PVD coating benefit machining with this insert? The PVD coating on the AH120 grade reduces adhesive wear and increases thermal resistance, which supports longer tool life and more consistent cutting-edge performance during turning cycles. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
DNMG 110412 AH6225 Wendeplatten - Tungaloy
The combination of a PVD‑coated carbide grade and ISO‑standard geometry ensures consistent edge stability and reliable chip control in medium turning operations. Benefit from the 55° rhombic form with a 1.2 mm corner radius for a balance of profile and strength; order the insert directly via Metav Werkzeuge or ask the consultants for application advice. DNMG110412 AH6225 — Turning insert (ISO, 55° rhombic) by Tungaloy The DNMG110412 AH6225 is an ISO‑standard turning insert designed for medium cutting of stainless steels, offering a PVD‑coated carbide grade and a 55° rhombic geometry optimised for stable cutting performance. PVD-coated carbide grade AH6225 ISO‑standard DNMG 110412 geometry Rhombic 55° shape, cylindrical hole 1.2 mm corner radius, double-sided chipbreaker Consistent cutting performance and wear resistance for medium turning The PVD‑coated carbide grade delivers a hard, wear‑resistant surface that keeps the cutting edge productive under changing conditions. The AH6225 designation denotes a universal grade tuned for stainless steels, combining a sharp, stable edge with resistance to built‑up edge and flank wear. The coating enhances adhesion and thermal stability during intermittent cuts and moderate speeds, which translates into more predictable tool life and fewer unscheduled indexings. Compatibility with the chosen holder depends on form, clearance angle, tolerance class, fastening method, size and thickness to guarantee secure clamping and repeatability. Geometry and clamping designed for interchangeability and reliable chip control The rhombic 55° configuration provides an efficient cutting angle for both external and internal turning while the cylindrical hole ensures positive seating in ISO‑type clamping systems. The insert is double‑sided with a 1.2 mm corner radius, giving two indexed cutting edges and a compromise between edge strength and profile definition. The integrated chipbreaker geometry supports stable chip formation in a range of feed and depth settings; this reduces vibration sensitivity and improves surface finish when paired with a suitably rigid holder and machine setup. Practical benefits for workshop productivity and process security As part of an ISO insert system, the element works within a simple system build: the insert, a matching external holder or boring bar, a support/locking set and replacement screws. This modularity speeds tool changes and simplifies inventory. For turning jobs where material and rigidity vary, selecting the AH6225 grade together with the appropriate chipbreaker yields fewer interruptions and a consistent surface quality, making the solution cost‑effective through reduced rework and steady productivity. The combination of geometry and coating therefore supports a reliable machining strategy across general turning tasks. For supply or application recommendations on the DNMG110412 AH6225 turning insert by Tungaloy, contact Metav Werkzeuge for availability and technical advice via info@metav-werkzeuge.com or call +49 2822 7131930 Technical Data Article number: 6947204 Manufacturer SKU: TUN6947204 Internal SKU: 6947204-Tungaloy Facts Geometry: DNMG 110412 (ISO) Shape angle: 55° Size: 11 Corner radius: 1.2 mm Free clearance angle: 0° Hole: with cylindrical hole Special features Grade: AH6225 (PVD‑coated carbide) Insert form: rhombic, double‑sided Chipbreaker: double‑sided Application: turning (external and internal) System components: ISO insert, holder/boring bar, support/clamping set, replacement screws FAQ What materials is this insert suited for? The DNMG110412 AH6225 insert is formulated primarily for stainless steels and performs well under the medium cutting conditions typical of such materials. Is the insert indexable on both sides? Yes, the insert is double‑sided and offers two usable cutting edges, enabling economical indexing and reduced tooling costs. How does the PVD coating affect performance? The PVD coating on the AH6225 grade provides improved wear resistance and thermal stability, which helps maintain a sharp cutting edge and stable chip control during intermittent cuts. Which holder types are compatible with this ISO insert? Compatibility is determined by form, clearance angle, tolerance class, fastening method, size and thickness; ISO‑type external holders and boring bars designed for DNMG inserts are suitable when matching those parameters. What is the benefit of the 1.2 mm corner radius? A 1.2 mm corner radius offers a compromise between edge strength and achievable surface finish, improving edge robustness without excessive cutting forces. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
DNMG 110412 AH6225 Wendeplatten - Tungaloy
Combining PVD-coated carbide durability with a stable, sharp cutting edge and ISO-standard geometry delivers consistent performance for turning operations; order the DNMG110412 AH6225 indexable insert directly via Metav Werkzeuge or consult our specialists for tailored advice. DNMG110412 AH6225 indexable turning insert – ISO rhombic, PVD-coated carbide by Tungaloy The DNMG110412 AH6225 is an ISO-standard indexable insert for external and internal turning, engineered for stable cutting in variable conditions and optimised for stainless steels. PVD-coated carbide for long tool life Sharp, stable cutting edge ISO-standard rhombic geometry Cylindrical hole with double-sided chipbreaker Greater process reliability through a robust cutting grade The AH6225 grade combines a PVD-coated carbide substrate with a cutting geometry designed for reliable metal removal when turning. This configuration promotes stable chip formation and extends tool life under medium cutting parameters, resulting in fewer insert changes and less downtime. The PVD layer increases wear resistance while maintaining an edge that resists chipping during interrupted cuts, which supports predictable cycle times and improved throughput for everyday production tasks. Easy integration into ISO-compatible tool systems The rhombic plate format and standardised dimensions ensure ISO compatibility with a wide range of external tool holders and boring bars. The DNMG110412 form factor, including the cylindrical centre hole, fastens securely to common clamping systems and benefits from a consistent tolerance class for repeatable seating. This predictability reduces setup time and facilitates quick insert indexation, enabling efficient changeovers and steady component quality across batches. Optimised for stainless steels and variable conditions AH6225 is a universal grade tailored to stainless steels, delivering a combination of a sharp, stable cutting edge and a double-sided chipbreaking geometry. The 55° plate angle and 1.2 mm corner radius produce a balance between surface finish and edge strength, helping to avoid built-up edge formation on adhesive materials. The double-sided chipbreaker assists in controlled chip segmentation during both continuous and interrupted cuts, reducing the risk of workpiece damage and easing chip evacuation. For recommendations on matching holders or to request technical sheets for the AH6225 grade, contact Metav Werkzeuge — email info@metav-werkzeuge.com or call +49 2822 7131930 to arrange support and ordering. Technical data Article number: 6947225 Manufacturer SKU: TUN6947225 Model series: ISO turning inserts Material: carbide (PVD-coated) Facts Insert size: 11 mm Plate thickness: 4.76 mm Corner radius: 1.2 mm Plate angle: 55° Centre hole: with cylindrical hole Special features Grade: AH6225 (PVD-coated carbide) Plate form: rhombic (DNMG) Chipbreaker: double-sided Application: external and internal turning Compatibility: ISO-standard holders and boring bars Edge condition: sharp yet stable, suitable for variable conditions FAQ What material is the AH6225 grade aimed at? The AH6225 grade is formulated for machining stainless steels, offering a balance of wear resistance and edge stability for medium turning operations. Can the DNMG110412 fit standard ISO holders? Yes — the DNMG110412 is an ISO-standard rhombic insert and is compatible with common external holders and boring bars that accept DNMG geometry. How does the PVD coating benefit tool life? The PVD-coated carbide surface on the DNMG110412 AH6225 reduces abrasive wear and improves thermal resistance, resulting in longer in-service life and fewer insert changes. Is this insert suitable for interrupted cuts? The combination of a stable cutting edge and the double-sided chipbreaker on the DNMG110412 AH6225 supports interrupted cutting conditions by resisting chipping and promoting controlled chip formation. What are the key dimensions to check when selecting a holder? Verify the insert size (11 mm), plate thickness (4.76 mm), corner radius (1.2 mm) and the plate angle (55°) to ensure correct seating and clamping in the chosen holder. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
DNMG 110412 AH6225 Wendeplatten - Tungaloy
Combine a sharp, stable cutting edge of the PVD-coated AH6225 grade with ISO compatibility and an indexable, double-sided design for efficient stainless-steel turning; order the insert directly via Metav Werkzeuge or consult our specialists for application guidance. DNMG 110412 AH6225 Tungaloy turning insert — PVD-coated carbide, 55° rhombic The DNMG110412 AH6225 is an ISO turning insert engineered for external and internal machining of stainless steels, offering a balance of sharpness and edge stability for medium cutting conditions. ISO rhombic insert DNMG 55° geometry PVD-coated carbide grade AH6225 Optimised for stainless steel turning Double-sided chipbreaker, indexable design High-performance cutting for stainless steels The DNMG110412 AH6225 insert combines a PVD coating with a carbide substrate to deliver a sharp, stable cutting edge that resists abrasive wear and maintains form under variable conditions. This results in predictable cutting forces and improved process stability when turning stainless steels, with a noticeable improvement in surface finish and repeatability. The 55° rhombic geometry helps to distribute cutting loads and supports efficient chip formation, which reduces the need for frequent tool changes and keeps cycle times low. System compatibility and application flexibility Designed as an ISO-norm insert, compatibility with a holder is defined by form, relief angle, tolerance class, fastening type, size and thickness. The rhombic shape and 0° clearance suit a wide range of external and internal turning operations; the double-sided design provides two usable edges per index for economical machining. Selection of the chipbreaker and grade should match workpiece material, machining type and setup rigidity to achieve consistent results in both stable and interrupted cutting conditions. Durable coating and economical tool life The AH6225 grade is a universal PVD-coated option optimised for a difficult-to-machine family such as stainless steels, offering good edge security at medium cutting parameters. The insert’s 1.2 mm corner radius and 4.76 mm thickness contribute to robust edge support, while the cylindrical hole ensures secure clamping and accurate repeatability. An indexable, double-sided format extends tool life per insert and reduces tooling costs, supporting continuous productivity and fewer machine stops for insert changes. For availability, application advice or to request a delivery proposal for the Tungaloy DNMG110412 AH6225 insert, contact Metav Werkzeuge at info@metav-werkzeuge.com or call +49 2822 7131930 — our consultants will advise on the optimal grade and holder combination for the intended turning task. Technical data Article number: 6966178 Manufacturer SKU: TUN6966178 Model series: ISO turning inserts Designation: DNMG110412 AH6225 Manufacturer: Tungaloy Core technical data Geometry angle: 55° Corner radius: 1.2 mm Thickness: 4.76 mm Size: 11 mm Relief angle: 0° Special features PVD-coated carbide grade AH6225 Rhombic insert form, double-sided chipbreaker Cylindrical hole for secure clamping For external and internal turning of stainless steels Indexable design, ISO-compatible FAQ What materials is this insert suitable for? The DNMG110412 AH6225 insert from Tungaloy is primarily designed for stainless steels, offering a universal grade that balances edge sharpness and wear resistance for medium machining tasks. Can the insert be used for both external and internal turning? Yes, the rhombic DNMG geometry and indexable, double-sided layout make it suitable for both external and internal turning operations when paired with a compatible ISO holder. What advantages does the PVD coating provide? The PVD-coated carbide construction of the AH6225 grade enhances wear resistance and edge life, which leads to more consistent machining outcomes and longer tool life under variable conditions. How does the corner radius affect the machining result? The 1.2 mm corner radius provides stronger edge support for interrupted cuts and roughing operations, improving robustness and reducing the risk of chipping during demanding stainless-steel turning. Which parameters determine compatibility with a toolholder? Compatibility depends on insert form, relief angle, tolerance class, fastening method, size and thickness; matching these parameters ensures secure clamping and correct cutting geometry with the selected holder. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
DNMG 110412 AH8015 Wendeplatten - Tungaloy
Take advantage of the PVD-coated carbide grade AH8015 and the ISO DNMG form for productive, reliable turning of heat‑resistant alloys; the balanced wear resistance and edge stability reduce downtime and maintain surface quality. Order the DNMG110412 AH8015 insert via Metav Werkzeuge or consult our technical team for application guidance. DNMG 110412 AH8015 ISO turning insert by Tungaloy — PVD-coated carbide, 55° rhombic form DNMG110412 AH8015 is a PVD-coated carbide indexable insert designed for general turning applications, especially where heat‑resistant alloys require a balanced mix of wear resistance and edge stability. PVD-coated carbide for heat‑resistant alloys ISO DNMG rhombic insert with 55° geometry Double‑sided insert with cylindrical hole 1.2 mm corner radius for improved surface finish Consistent cutting performance through a balanced grade The AH8015 grade is a PVD‑coated carbide formulation engineered as a first choice for general machining of heat‑resistant alloys, offering a compromise between wear resistance and edge stability. This balance translates into more predictable tool life and steady cutting behaviour when machining demanding materials. Selecting a grade with these characteristics helps to avoid premature edge chipping while maintaining acceptable flank wear, supporting consistent component quality over serial production runs. Ease of integration into ISO tooling systems The insert follows the ISO DNMG format with a 55° rhombic geometry and a 0° clearance angle, which makes it compatible with a wide range of standard external and internal turning holders. Key dimensions such as 11 mm inscribed circle and 4.76 mm thickness ensure a precise fit in holders designed for DNMG‑type plates. The insert is double‑sided and supplied with a cylindrical hole for secure fastening; these features reduce inventory complexity and allow economical use of both cutting edges before replacement is required. Practical benefits for workshop productivity With a 1.2 mm corner radius and a double‑sided chipbreaker arrangement, the plate supports good surface finish and stable chip formation in interrupted and continuous cuts. The ISO‑compliant form and standardised thickness simplify tool management: matching the correct holder, shim and clamping set ensures repeatable results. The system concept—indexable insert, compatible external holder or boring bar, shim/clamp set and spare screws—means faster changeovers and less unplanned downtime, contributing to overall process efficiency. For application advice, availability or to discuss batch requirements for the Tungaloy AH8015 grade, contact Metav Werkzeuge — phone +49 2822 7131930 or email info@metav-werkzeuge.com — our consultants will advise on holder compatibility and optimal chipbreaker selection Technical data Article number: 6947226 Manufacturer SKU: TUN6947226 Brand: Tungaloy Grade: AH8015 Designation: DNMG110412 Dimensions & numbers Inscribed circle: 11 mm Thickness: 4.76 mm Corner radius: 1.2 mm Cutting angle: 55° Clearance angle: 0° Features & applications Material: carbide, PVD‑coated Shape: rhombic (DNMG) Double‑sided with cylindrical hole Chipbreaker: double‑sided Typical use: external and internal turning System components: compatible holder, shim/clamp set and replacement screws Compatibility determined by form, clearance angle, tolerance, fastening, size and thickness FAQ Which materials is this insert suitable for? The DNMG110412 AH8015 insert is optimised for machining heat‑resistant alloys; the PVD‑coated carbide grade provides a balance of wear resistance and edge stability suited to these materials. What are the key dimensions and geometry of the insert? The plate follows ISO DNMG form with an 11 mm inscribed circle, 4.76 mm thickness, 55° geometry and a 1.2 mm corner radius for improved surface finish. How is the insert mounted and secured? The indexable insert is double‑sided and supplied with a cylindrical hole for secure fastening; compatibility with a holder depends on form, clearance, tolerance, fastening method, size and thickness. Can this plate be used for both external and internal turning? Yes, the DNMG110412 format and the AH8015 grade are suitable for both external and internal turning when matched with the appropriate holder and cutting parameters. What advantage does the AH8015 grade offer compared with other grades? AH8015 offers a balanced compromise between wear resistance and edge stability, making it a first choice for general machining of heat‑resistant alloys where predictable tool life and consistent surface quality are required. Manufacturer/Responsible: Tungaloy‑NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand‑new product from the manufacturer.
DNMG 110412 AH8015 Wendeplatten - Tungaloy
Combine PVD‑coated cemented carbide with a double‑sided chipbreaker and ISO‑standard geometry for consistent turning performance and reliable edge life; order the insert directly via Metav Werkzeuge or ask our consultants for compatibility support. DNMG 110412 AH8015 Tungaloy indexable turning insert – PVD‑coated carbide, double‑sided chipbreaker for turning The DNMG110412 AH8015 Tungaloy turning insert is an ISO‑standard, rhombic indexable insert engineered for external and internal turning operations of heat‑resistant alloys. PVD‑coated carbide for heat resistance Double‑sided chipbreaker for secure chip control ISO DNMG 110412 form, rhombic 55° geometry 1.2 mm nose radius, 4.76 mm plate thickness Proven cutting performance for heat‑resistant alloys The AH8015 grade is a PVD‑coated cemented carbide developed as a first choice for the general machining of heat‑resistant alloys, offering a balanced combination of wear resistance and edge stability. This composition reduces flank and crater wear under elevated temperatures, which leads to fewer insert changes and steadier component quality. The result is improved process reliability and a predictable tool life that supports continuous production runs. Precisely defined geometry for stable machining The insert’s ISO DNMG 110412 geometry and 55° rhombic form provide a stable cutting edge and straightforward seat in standard holders. Compatibility with a lathe toolholder is determined by form, relief angle (0°), tolerance class, fastening method, size and thickness; these parameters are key to secure clamping and vibration‑free cutting. The 1.2 mm nose radius delivers a compromise between edge strength and surface finish, while the double‑sided chipbreaker supports effective chip control across a range of feeds. Practical advantages in workshop use When paired with a matching external holder, clamping set and replacement screw, this insert enables efficient set‑up changes and minimal downtime. The balanced grade and chipbreaker combination promotes stable chip formation, which simplifies chip removal and reduces risk to workpiece finish. For turning operations where heat resistance and consistent cutting behaviour are required, the insert contributes to process efficiency and reproducible results. For tailored advice on holder selection and to order Tungaloy turning inserts such as DNMG110412 AH8015 through Metav Werkzeuge, contact our specialists for precise matching and rapid supply. Technical data Article number: 6793727 Manufacturer SKU: TUN6793727 SKU: 6793727-Tungaloy Model series: ISO turning insert series Name: DNMG110412 AH8015 Tungaloy turning insert Core data Insert size: 11 mm Plate thickness: 4.76 mm Nose radius: 1.2 mm Relief angle: 0° Insert angle: 55° Hole: with hole Hole style: cylindrical hole Plate form: rhombic Special features Material: cemented carbide Grade/coating: AH8015, PVD‑coated Chipbreaker: double‑sided Intended application: Turning System components: indexable insert, appropriate external holder, clamping set, replacement screws FAQ Which materials are best suited for this insert? The DNMG110412 AH8015 insert is intended primarily for heat‑resistant alloys; the AH8015 grade balances wear resistance and edge stability for general machining of such materials. How is holder compatibility ensured? Compatibility is determined by insert form, relief angle (0°), tolerance class, fastening, size and thickness; matching these parameters to the toolholder guarantees correct seating and clamping. Is the insert reversible and how many cutting edges are available? This is a double‑sided indexable insert; each usable edge is available when the insert is indexed, allowing multiple cutting edges per insert. What are the advantages of the AH8015 grade? AH8015, a PVD‑coated carbide, provides a compromise between wear resistance and edge stability, making it suitable for consistent performance in demanding turning operations. What practical items are needed to mount the insert? A matching external holder, a suitable clamping set and the correct replacement screw are required; secure clamping is essential for optimal cutting performance. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand‑new product from the manufacturer.
DNMG 110412 AH8015 Wendeplatten - Tungaloy
Benefit from the combination of PVD-coated carbide and a double-sided chipbreaker to achieve consistent chip control and dependable edge life in turning operations; order the DNMG110412 AH8015 directly via Metav Werkzeuge or consult the Metav Werkzeuge advisers for application support. DNMG110412 AH8015 — ISO turning insert (PVD-coated carbide, 55°) by Tungaloy The DNMG110412 AH8015 is an ISO-standard indexable insert for external and internal turning, designed for reliable machining of heat‑resistant alloys and balanced wear resistance across variable cutting conditions. ISO-standard rhombic insert 55° geometry PVD-coated carbide grade AH8015 Double-sided chipbreaker for consistent chips Cylindrical hole compatible with standard holders Precision and lasting cutting performance for heat‑resistant alloys The combination of a PVD-coated surface with a carbide substrate in grade AH8015 provides a measured balance between wear resistance and edge stability, making the insert suitable as a first choice for machining heat‑resistant alloys. The PVD layer reduces adhesive wear and improves thermal resistance at the cutting edge, while the substrate sustains mechanical strength. This balance results in predictable tool behaviour under varying feeds and speeds, supporting stable cycle times and reproducible surface quality on turned components. Seamless integration into ISO tool systems with clear compatibility cues Compatibility with standard toolholders is governed by form, relief angle, tolerance class, clamping style, size and thickness; the rhombic 55° geometry and a 0° relief angle enable secure seating in many external holders and boring bars. Key dimensions such as 11 mm inscribed size and a 4.76 mm plate thickness ensure correct fitment into ISO‑rated clamping systems, while the cylindrical hole permits positive fixation and straightforward indexation. These defined parameters simplify tool planning and reduce the need for custom adapters in most turning setups. Operational advantages and recommended cutting tasks The double-sided chipbreaker supports consistent chip control, reducing manual interventions and helping to maintain stable cutting forces during both external and internal turning. The insert is intended for general turning tasks on heat‑resistant alloys; selecting the matching chipbreaker and grade according to workpiece material and machine stability optimises productivity. A complete system approach is recommended — an ISO insert, matched external holder or boring bar, shim/clamp set and replacement screws — to achieve repeatable performance and minimise downtime in production environments. Contact Metav Werkzeuge to discuss application specifics for Tungaloy DNMG110412 AH8015 inserts and to arrange a tailored supply or technical consultation with Metav Werkzeuge Technical data Article number: 6966179 Manufacturer SKU: TUN6966179 Brand: Tungaloy Model series: ISO turning indexable inserts Material: Carbide Facts Size: 11 mm Thickness: 4.76 mm Corner radius: 1.2 mm Included angle: 55° Relief angle: 0° Special features Grade/coating: AH8015, PVD‑coated carbide Chipbreaker: Double‑sided Plate shape: Rhombic (55°) Hole style: Cylindrical hole (with hole) System components: ISO insert, holder/boring bar, shim/clamp set, replacement screws Typical application: External and internal turning; choose chipbreaker and grade to match material and stability FAQ What materials is this insert primarily designed for? The DNMG110412 AH8015 insert is specified as a first choice for general machining of heat‑resistant alloys, delivering a balance of wear resistance and edge stability suited to those materials. How does the AH8015 grade improve cutting performance? The AH8015 PVD‑coated carbide grade combines thermal resistance from the coating with carbide substrate strength, improving edge life and reducing adhesive wear in demanding turning operations. Is this insert reversible and how many edges are available? Yes — the insert is double‑sided with a chipbreaker on both faces, enabling indexation to a fresh cutting edge to extend productive tool life. Which holder types are compatible with this insert? Compatibility depends on form, relief angle, tolerance class, clamping and size; the 55° rhombic geometry and cylindrical hole facilitate use with standard 55° external holders and appropriate boring bars when matched to the insert dimensions. What are the key dimensions and identifiers for ordering? Refer to article number 6966179 and manufacturer SKU TUN6966179; key dimensions include an 11 mm inscribed size, 4.76 mm thickness and a 1.2 mm corner radius. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
DNMG 110412 AH8015 Wendeplatten - Tungaloy
Combining a PVD‑coated AH8015 carbide grade with the ISO rhombic DNMG geometry and a 1.2 mm corner radius yields a versatile turning solution that balances wear resistance and cutting‑edge stability for heat‑resistant alloys. Order directly via Metav Werkzeuge or consult the technical team for application matching. DNMG 110412 AH8015 turning insert by Tungaloy — ISO DNMG form for turning, PVD‑coated carbide, 1.2 mm radius The DNMG110412 AH8015 is an ISO rhombic, double‑sided turning insert engineered for general turning of heat‑resistant alloys; it combines a PVD‑coated carbide grade with stable edge geometry for consistent material removal. PVD‑coated AH8015 carbide grade ISO rhombic DNMG form 1.2 mm corner radius for robustness Double‑sided insert with cylindrical hole Dependable wear resistance for heat‑resistant alloys The PVD‑coated AH8015 grade is formulated as a balanced solution between wear resistance and edge stability, making this indexable insert suitable for continuous production runs on heat‑resistant alloys. The PVD coating reduces adhesion and crater wear at elevated temperatures, which in turn prolongs tool life and maintains surface finish. For operations where thermal stability and repeatable cycle times matter, the coated carbide substrate offers predictable performance and reduced downtime. Secure seating and broad holder compatibility for consistent results Compatibility with toolholders is defined by form, relief angle, tolerance class, fixation, size and thickness; the ISO DNMG designation standardises these parameters so the insert fits a wide range of external and internal turning holders. The insert’s 0° relief and rhombic geometry enable reliable clamping and positional repeatability. In a typical system set‑up the insert works together with a matching holder, a shim or clamp set and replacement screws to ensure repeatable seating and minimum run‑out during cutting. Geometry engineered for chip control and productivity A 1.2 mm corner radius and the supplied double‑sided chipbreaker support stable cutting forces and improved chip formation, reducing vibration and enhancing surface integrity. The rhombic contour and the presence of a cylindrical hole enable multiple indexing options and secure fastening in robust holders. Plate dimensions (11 mm inscribed circle, 4.76 mm thickness) contribute to stiffness in the cutting zone, which supports higher material removal rates and consistent cycle times on demanding workpieces. Practical selection advice and safe handling Selection of the appropriate chipbreaker and cutting data should be guided by the workpiece material and machine stability: choose the chipformer and grade to match the alloy, feed and depth of cut for best results. The insert is indexable and double‑sided, allowing economical re‑use of the second cutting edge after rotation. Handling and storage should avoid contamination of the cutting edges; worn inserts should be removed from service and replaced to maintain process reliability. For complex or high‑temperature applications, consult the technical documentation or request further machining data. Contact Metav Werkzeuge for tailored application support and to secure DNMG110412 AH8015 inserts from Tungaloy; eMail info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: 6793732 Manufacturer SKU: TUN6793732 SKU: 6793732-Tungaloy Model series: ISO turning indexable inserts Core data Insert designation: DNMG110412 Corner radius: 1.2 mm Plate size (inscribed circle): 11 mm Thickness: 4.76 mm Relief angle: 0° Included angle: 55° Special features Material: PVD‑coated carbide Grade: AH8015 Shape: rhombic Hole: cylindrical hole Chipbreaker: double‑sided Application: turning (external and internal) ISO standard DNMG compatibility; holder fit depends on form, relief, tolerance, fixation, size and thickness FAQ Which materials is this insert best suited for? The DNMG110412 AH8015 insert is intended primarily for heat‑resistant alloys; the AH8015 grade offers a balance of wear resistance and cutting‑edge stability for such materials. Can the insert be indexed and reused? Yes, the insert is double‑sided and designed for indexing; after rotating to the second edge the insert can be reused, extending tool economy. What does the PVD coating provide during turning? The PVD‑coating reduces adhesive wear and improves thermal resistance at the cutting edge, resulting in longer life and more consistent surface finish during turning of demanding alloys. How is compatibility with holders ensured? Compatibility is achieved by matching the ISO DNMG form and checking the relief angle, tolerance class, fixation method, size and thickness against the chosen holder. What are the key dimensions to note for fixture and programme setup? Relevant dimensions are the inscribed circle 11 mm, thickness 4.76 mm, corner radius 1.2 mm and included angle 55°, which determine clamping and cutting geometry. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
DNMG 110412 AT9530 Wendeplatten - Tungaloy
Take advantage of proven cermet performance and ISO compatibility for consistent finishing results; the combination of the AT9530 coated grade and a 1.2 mm corner radius supports high-quality surface finish and predictable tool life. Order via Metav Werkzeuge or consult the team for application-specific recommendations. DNMG110412 AT9530 Tungaloy turning insert — ISO rhombic 55°, coated cermet The DNMG110412 AT9530 is a rhombic ISO turning insert designed for finishing and light machining of steel with emphasis on surface quality and uniform wear Coated cermet grade AT9530 optimised for finish Rhombic 55° geometry for versatile turning 1.2 mm corner radius for improved surface finish Double-sided insert with cylindrical locating hole Superior surface quality through a cermet grade built for finishing The combination of AT9530 and a coated cermet substrate is targeted at finishing and light-turning operations where surface integrity matters most. The composition of the grade reduces adhesive wear and produces a consistent cutting edge, which leads to a uniform wear pattern and fewer workpiece rejections. The moderate cutting-edge geometry reduces cutting forces and vibrations during finish passes, making the insert particularly effective where a high-quality surface is required rather than aggressive material removal. Reliable integration into ISO holder systems for minimal setup time Designed as an ISO-standard indexable insert, compatibility with a matching holder depends on form, clearance angle, tolerance class, attachment method, size and thickness. The rhombic plate form and 4.76 mm plate thickness ensure mechanical stability when clamped in a suitable DNMG pocket. The presence of a cylindrical locating hole supports accurate seating and repeatable positioning, which shortens set-up time and reduces variability between tool changes. Geometry and chip control tuned for finishing applications The insert’s 55° included angle and 1.2 mm corner radius combine to produce a favourable contact geometry for external and internal turning. The double-sided chipbreaker supports two usable cutting edges, helping to extend indexable life and maintain process continuity. A 0° clearance angle and the selected chip control ensure predictable chip formation during low-to-moderate depth finishing cuts, which contributes to a consistently fine surface and simplified chip evacuation. Productivity gains from consistent tool life and grade stability By favouring a coated cermet designed for finishing, the insert reduces the need for repeated dressing or frequent tool swaps, improving overall throughput for fine-turning operations. Consistent edge rounding and stable wear behaviour lower the risk of sudden edge failure, contributing to predictable tool life and fewer process interruptions. For operations where surface finish and repeatability are priorities, this insert offers a pragmatic balance between performance and availability under Tungaloy quality control. For application advice, toolholder matching or immediate availability of Tungaloy turning inserts, contact Metav Werkzeuge at info@metav-werkzeuge.com or call +49 2822 7131930 for expert guidance and rapid delivery Technical Data Article number: 6773697 SKU: 6773697-Tungaloy Manufacturer item number: TUN6773697 Model series: ISO turning inserts Application: Turning Material: carbide Facts Corner radius: 1.2 mm Relief/clearance angle: 0° Included angle: 55° Plate thickness: 4.76 mm Inscribed circle / plate size: 11 Double-sided: yes Special features Grade/coating: AT9530 (coated cermet) Plate form: rhombic Hole: with cylindrical hole Chipbreaker: double-sided System designation: DNMG110412 ISO series: ISO turning inserts Brand: Tungaloy FAQ Is this insert suitable for finishing steel? Yes. The DNMG110412 AT9530 Tungaloy turning insert is optimised for finishing and light machining of steel, prioritising surface quality and uniform wear. Which toolholders are compatible with this insert? Compatibility requires a matching ISO DNMG pocket; fit is determined by form, clearance angle, tolerance class, attachment, size and thickness—ensure the holder matches the DNMG geometry. Can the insert be indexed to present a fresh cutting edge? Yes. The insert is double-sided, allowing indexing to a second edge to extend usable life and maintain process continuity. What surface quality improvements are expected with this grade? The AT9530 coated cermet grade delivers improved surface finish through stable cutting-edge behaviour and reduced adhesion, resulting in fewer finish passes and more consistent results. How should the chipbreaker be selected for different turning tasks? The double-sided chipbreaker included on this insert is intended for finishing applications; for other operations, choose a chipbreaker matched to material, feed and depth of cut. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
DNMG 110412 GT9530 Wendeplatten - Tungaloy
Take advantage of GT9530 coated cermet performance and ISO‑standard geometry for consistent finishing and longer tool life in turning applications; order or request advice via Metav Werkzeuge for reliable supply and application support. DNMG 110412 GT9530 DNMG110412 Turning Insert – ISO cermet, 55° rhombic (Tungaloy) The DNMG110412 GT9530 is an ISO‑standard rhombic turning insert designed for finishing to light universal turning in steel, offering a wear‑resistant cermet grade for improved surface quality. ISO‑standard rhombic insert 55° GT9530 coated cermet for steel 1.2 mm corner radius for superior finish Double‑sided with cylindrical hole for secure clamping Consistent finish and extended life for stable production The GT9530 grade is a coated cermet engineered to provide improved surface quality and extended tool life under stable machining conditions. Compared with conventional finishing grades, the material composition of this insert reduces adhesive wear and supports consistent part finish, which leads to fewer rework cycles and a more predictable process. Choosing a carbide‑based insert with cermet coating helps maintain tolerances over longer tool life, benefiting production runs where repeatability and surface integrity are priorities. Geometry tailored for precision turning and secure clamping With a 55° rhombic shape and a 1.2 mm corner radius, the insert balances edge strength and finishing capability. The neutral 0° clearance angle and the double‑sided chipbreaker allow both indexable use and predictable chip formation when paired with an appropriate holder. The cylindrical hole provides secure clamping and simple alignment in standard ISO clamping systems. Because compatibility depends on holder form, clearance angle, tolerance class, fastening and plate thickness, selecting the correct clamp and mounting hardware ensures stable cutting conditions and repeatable results. Simple integration into ISO tool systems and practical benefits As part of an ISO turning insert series, the item integrates easily into most established toolholder systems, reducing setup time and inventory complexity. The insert’s construction supports finishing and light universal operations in steel, where a good surface finish and longer edge life are required. For shops converting from brazed tips or non‑indexed tooling, switching to an ISO indexable solution like this insert can improve uptime and simplify tool management without major changes to existing holders. Application guidance and selection advice This grade and geometry are intended primarily for turning of steel and similar materials where stability can be maintained. The double‑sided design doubles indexing possibilities, improving economy. Choose the chipbreaker and grade according to workpiece material, machining type and machine stability: a finer chip control suits finishing, while alternative grades may be preferable for heavy roughing. The DNMG110412 format is a widely used option for external and internal turning operations where surface quality is critical. For precise selection and availability of the Tungaloy DNMG110412 GT9530 insert, contact Metav Werkzeuge for tailored advice and reliable delivery — email info@metav-werkzeuge.com or call +49 2822 7131930 to discuss application details or to reserve stock. Technical data Article number: 6710245 Manufacturer SKU: TUN6710245 SKU: 6710245-Tungaloy ISO designation: DNMG110412 Material: carbide Grade/coating: GT9530 (coated cermet) Shape: rhombic Hole: with cylindrical hole Facts Angle: 55° Corner radius: 1.2 mm Size: 11 mm Clearance angle: 0° Double‑sided: yes Manufacturer article number: 6710245 Special features Coated cermet grade GT9530 Designed for finishing to light universal turning in steel Double‑sided chipbreaker for reliable chip control ISO‑standard insert for straightforward holder compatibility Compatibility determined by form, clearance, tolerance, fastening, size and thickness FAQ What materials is this insert suitable for? The DNMG110412 GT9530 insert is optimised for machining steel and is intended for finishing to light universal turning operations where good surface quality and extended tool life are required. How is the insert secured in the holder? The insert uses a cylindrical hole and standard ISO clamping principles; secure clamping with the correct seat and screw ensures stable cutting and repeatable results for the Tungaloy DNMG110412 GT9530. Can both sides of the insert be used? Yes, the insert is double‑sided, offering multiple indexable edges to improve economy and reduce tooling changeovers for turning tasks. What chip control can be expected with this grade? With its double‑sided chipbreaker, the GT9530 grade provides controlled chip formation in finishing applications; select the chipbreaker and cutting parameters to match the workpiece and machine stability. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
DNMG 110412 NS9530 Wendeplatten - Tungaloy
Take advantage of the combination of ISO conformity, a sharp uncoated cermet cutting edge and a compact 1.2 mm corner radius for reliable finishing of steel components; order directly via Metav Werkzeuge or consult our technical team for process advice. DNMG110412 NS9530 DNMG 110412 finishing turning insert — uncoated cermet, 55° — Tungaloy DNMG110412 NS9530 is an indexable turning insert designed for finishing operations in steel machining, offering a sharp cutting edge and low cutting forces for superior surface quality ISO-standard rhombic insert, 55° Uncoated cermet grade NS9530 for finishing Low cutting forces and high surface finish Double-sided chipbreaker, cylindrical hole Precision finishing through material and geometry The combination of an uncoated cermet substrate and the NS9530 grade yields a cutting edge optimised for finishing steel. Cermet materials provide a harder, more wear-resistant edge than many conventional carbides, which helps to maintain a sharp cutting edge over extended runs. This results in low cutting forces and reduced tendency for built-up edge; the benefit for production is clearer: fewer rework cycles and consistently better surface integrity on turned parts. The insert’s design supports continuous cuts and small depths of cut, where surface finish and dimensional stability are decisive. Compatibility and secure clamping for predictable results The insert conforms to ISO plate geometry DNMG110412, so compatibility with holders depends on plate form, clearance angle, tolerance class, fastening, size and thickness. The rhombic outline and cylindrical hole permit reliable centring and clamping when using matched external holders or boring bars. Using a correctly matched holder ensures the tool seat and clamp apply uniform pressure, which preserves the insert’s geometry and contributes directly to repeatable dimensional results and consistent tool life. Productivity advantages in finishing operations With a 55° included angle and a 1.2 mm corner radius, the insert balances edge strength and finish capability for fine turning tasks. The double-sided chipbreaker supports stable chip formation at finishing feeds, reducing vibration and improving surface quality. Less cutting force translates into lower spindle load and often reduced cycle time for finishing passes. For shops aiming to increase throughput without sacrificing finish, this insert enables economical, repeatable machining where tight tolerances and fine surfaces are required. Practical notes on application and handling The grade is intended primarily as a finishing grade for steel; it performs best in continuous cutting conditions with modest depths of cut and steady feeds. When selecting parameters, prioritise stable workholding and moderate cutting speeds suited to cermet behaviour to avoid thermal shock or premature edge degradation. Indexing the insert to use both sides extends usable life, while correct torque on the clamping screw preserves seating accuracy and repeatability. For demanding finishing of steel components, select the Tungaloy DNMG110412 NS9530 insert and contact Metav Werkzeuge for process guidance at info@metav-werkzeuge.com or by phone on +49 2822 7131930 Technical data Article number: 6710205 SKU: 6710205-Tungaloy Manufacturer item number: TUN6710205 Manufacturer: Tungaloy Facts Angle: 55° Corner radius: 1.2 mm Size: 11 mm Clearance angle: 0° Special features ISO designation: DNMG110412 Grade: NS9530, uncoated cermet Material: Cemented carbide Plate shape: Rhombic Hole: Cylindrical, with hole Chipbreaker: Double-sided Typical use: Turning / finishing steel FAQ What materials is this insert suitable for? The DNMG110412 NS9530 insert is optimised for finishing operations in steel, delivering low cutting forces and high surface quality in continuous cuts and small depths of cut. How does the uncoated NS9530 grade differ from coated alternatives? NS9530 is an uncoated cermet finishing grade that retains a very sharp edge for improved surface finish; compared with coated grades it often offers lower cutting forces and better dimensional control in finishing applications. How can compatibility with an existing holder be verified? Compatibility depends on the DNMG geometry—check holder seat form, clearance angle, tolerance class, fastening method, size and plate thickness to ensure proper clamping and repeatable positioning. Is the insert suitable for interrupted or heavy roughing cuts? This grade is intended for finishing; heavy interrupted cuts or aggressive roughing are not ideal for NS9530 due to its emphasis on sharp-edge performance rather than extreme edge toughness. What are the key geometry specifications to note before programming a toolpath? Note the 55° included angle, the 1.2 mm corner radius and the 0° clearance angle when calculating engagement, feeds and speeds for accurate finishing passes. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
DNMG 110412 T6215 Wendeplatten - Tungaloy
Take advantage of the combination of CVD-coated carbide wear resistance, precise 55° geometry and a 1.2 mm corner radius for consistent turning results and longer tool life; order matching holders and accessories through Metav Werkzeuge or contact their team for application advice. DNMG110412 T6215 indexable turning insert — turning for stainless steels by Tungaloy The DNMG110412 T6215 is an ISO-standard indexable turning insert designed for stable to lightly interrupted turning of stainless steels, offering a rhombic 55° geometry and a robust CVD-coated carbide grade for reliable performance. CVD-coated carbide for prolonged wear resistance 55° rhombic plate with 1.2 mm corner radius Double-sided chipbreaker for versatile turning ISO-compliant fit with cylindrical hole Consistent wear resistance for demanding stainless-steel turning The combination of a CVD coating and a wear-resistant carbide substrate ensures predictable flank and crater wear behaviour when machining stainless steels under stable cutting conditions. The selected grade is formulated for good adhesion of the coating and a balanced substrate toughness, which together reduce the frequency of insert changes and contribute to lower process costs over time. This technical design supports a continuous production flow by maintaining cutting performance and surface quality across long batch runs. Geometry and edge preparation that improve surface finish and tool life A 55° geometry with a 1.2 mm corner radius provides a stable cutting edge that distributes cutting forces and reduces cutting-edge chipping risk, especially in external and internal turning operations. The moderate corner radius helps to combine chip strength with a smooth surface finish, while the plate thickness of 4.76 mm contributes to rigidity in overhang situations. The rhombic plate form and double-sided chipbreaker enable two usable cutting edges per orientation, improving material utilisation and extending effective tool life. System compatibility and practical machining advantages Designed as part of an ISO-standard system, this insert locates via a cylindrical centre hole and mates with compatible external holders or boring bars; holder compatibility is determined by form, clearance angle, tolerance class, clamping method, size and thickness. The double-sided chipbreaker offers flexibility across a range of feeds and depths, simplifying process setup when switching between finishing and medium cutting tasks. Where intermittent cuts occur, the insert’s balanced substrate and coating combination deliver stable cut control and reproducible results in serial production. For technical clarification or holder recommendations, experienced advisers can support selection of the appropriate seating and clamping components. Contact Metav Werkzeuge for application advice on Tungaloy CVD inserts and to obtain matching holders — email info@metav-werkzeuge.com or call +49 2822 7131930. Technical Data Article number: 6966177 SKU: 6966177-Tungaloy Manufacturer article number: TUN6966177 Model series: ISO-Drehwendeschneidplatten Facts Plate designation: DNMG110412 Grade / coating: T6215 (CVD-coated) Material: Hartmetall (carbide) Thickness: 4.76 mm Size: 11 mm Corner radius: 1.2 mm Insert angle: 55° Clearance angle: 0° Special features Rhombic plate form Cylindrical centre hole (with hole) Double-sided chipbreaker ISO-standard indexable insert for turning Intended for stable to lightly interrupted turning of stainless steels System components: insert, appropriate external holder or boring bar, seat/locking kit and replacement screws FAQ What materials is this insert suitable for? The DNMG110412 T6215 turning insert is designed primarily for machining stainless steels under stable to lightly interrupted conditions; the CVD-coated carbide substrate provides wear resistance suitable for such applications. How does the 55° geometry affect machining performance? A 55° rhombic geometry reduces radial cutting forces and offers a compromise between access in internal turning and edge strength, helping to improve surface finish and stability during turning operations with the Tungaloy insert. Can this insert be used on both external and internal turning applications? Yes, the rhombic shape and the ISO-compliant fixation allow use in both external and internal turning setups when paired with the correct external holder or boring bar compatible with the DNMG110412 form. How many cutting edges are available per insert? The insert features a double-sided chipbreaker arrangement, providing multiple usable cutting edges and enabling economical indexation during production runs. What information is needed to ensure holder compatibility? Compatibility is determined by the insert form, clearance angle, tolerance class, clamping method, size and thickness; refer to the ISO designation DNMG110412 and the insert thickness of 4.76 mm when selecting an external holder. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
DNMG 110412 T6215 Wendeplatten - Tungaloy
Take advantage of a CVD-coated T6215 grade and the ISO DNMG110412 form to ensure durable performance when turning rostfreier Stahl; the rhombic 55° geometry with a 1.2 mm corner radius delivers consistent surface quality and reliable edge life. Order the DNMG110412 T6215 indexable insert directly via Metav Werkzeuge or contact our consultants for compatibility advice. DNMG110412 T6215 indexable turning insert (Tungaloy) A DNMG110412 T6215 indexable insert engineered for precision external and internal turning of rostfreier Stahl under stable to mildly interrupted cutting conditions CVD-coated wear-resistant grade T6215 ISO DNMG 110412 rhombic 55° insert 1.2 mm corner radius for consistent finishes Double-sided geometry with central cylindrical hole Durable grade and coating for longer cutting life The T6215 grade is a CVD-coated cemented carbide specifically developed for wear resistance during the machining of rostfreier Stahl. The coating provides a hard, thermally stable layer that reduces flank wear and protects the carbide substrate at elevated temperatures, which results in longer productive tool life. In practical terms, this means fewer indexings and less frequent insert changes, improving process economy and lowering downtime in serial and batch production. The coating behaviour under interrupted cuts remains stable, making the insert suitable for turning operations where slight interruptions can occur. Geometry engineered for surface quality and predictable results The ISO DNMG110412 rhombic shape with a 55° included angle and a 1.2 mm corner radius balances strength and accessibility: the angle permits versatile approach possibilities while the radius supports consistent surface finishes without excessive cutting forces. The insert is double-sided, providing four usable cutting edges per indexable item, and features a cylindrical central hole for secure mounting. Compatibility with a toolholder depends on form, clearance angle, tolerance class, fastening and thickness; the system is composed of the insert, a matching external holder or boring bar, a shim/clamp set and replacement screws, which together ensure repeatable seating and clamping for accurate run-out and chatter control. Practical integration and production advantages Using this indexable plate supports cost-effective machining through repeatable edge performance and straightforward inventory control: the double-sided design and standard ISO form simplify stocking and tool-change procedures. The 4.76 mm plate thickness contributes to rigidity in the cutting zone, reducing vibration and improving surface quality when paired with a stable holder. Selection of the correct chipbreaker and grade should be aligned with workpiece material, machining approach and machine stability to extract maximum productivity. Where process assurance and consistent part finish are priorities, the combination of grade, coating and geometry delivers an efficient solution for modern turning shops. Contact Metav Werkzeuge today for tailored advice on toolholder compatibility and supply of the Tungaloy DNMG110412 T6215 insert; email info@metav-werkzeuge.com or call +49 2822 7131930 for fast, expert support Technical data Article number: 6944680 Manufacturer article number: 6944680 SKU: 6944680-Tungaloy Manufacturer SKU: TUN6944680 Core specifications ISO designation: DNMG110412 Insert size: 11 Plate thickness: 4.76 mm Clearance angle: 0° Included angle: 55° Corner radius: 1.2 mm Features and compatibility Material: cemented carbide Grade / coating: T6215, CVD-coated Application: Turning Geometry: rhombic, double-sided Hole: with central cylindrical hole Chipbreaker: double-sided Model series: ISO turning indexable inserts System components: insert, external holder or boring bar, shim/clamp set, replacement screws FAQ What materials is this insert suited for? The DNMG110412 T6215 insert is designed primarily for machining rostfreier Stahl; the T6215 CVD-coated cemented carbide offers wear resistance appropriate for stable to mildly interrupted turning operations. How many cutting edges are available per insert? The rhombic DNMG form is double-sided, providing four usable cutting edges per insert, which helps to reduce tooling costs and changeover frequency. What determines compatibility with a toolholder? Compatibility is determined by the insert form, clearance angle, tolerance class, fastening method, size and thickness; matching the DNMG110412 form and thickness with a compatible holder ensures correct seating and repeatable run-out. Can this insert handle interrupted cuts? The wear-resistant T6215 grade performs well under stable to slightly interrupted cutting; for severe interruptions, a more robust geometry or a different grade should be considered. What chipbreaker does the insert use? This item has a double-sided chipbreaker; selection of a specific chip control should be aligned with the workpiece material and cutting parameters for optimal chip formation. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
DNMG 110412 T6215 Wendeplatten - Tungaloy
High wear resistance from the CVD‑coated carbide T6215, ISO‑standard geometry for reliable clamping, and a double‑sided chipbreaker for consistent chip control — order the insert directly via Metav Werkzeuge or contact our consultants for application advice. DNMG110412 T6215 — indexable insert for turning, Tungaloy The DNMG110412 T6215 is an ISO‑standard rhombic indexable insert designed for turning applications, optimised for machining rostfreier Stahl under stable to lightly interrupted cutting conditions ISO rhombic insert DNMG110412 CVD-coated carbide grade T6215 1.2 mm corner radius for versatile turning Double-sided chipbreaker, cylindrical hole Durable coating and material for extended tool life The combination of a CVD‑coated carbide substrate and the T6215 grade provides a wear‑resistant cutting edge that maintains performance over longer production runs. For machining rostfreier Stahl this insert offers improved edge stability, which reduces flank wear and the frequency of tool changes. The coating enhances thermal resistance and lowers adhesive tendencies during cutting, translating into fewer interruptions and steadier component quality over time. This contributes directly to predictable productivity and reduced per‑part tooling costs. ISO compatibility and secure clamping minimise setup variation Manufactured to ISO dimensions, the insert guarantees compatibility with holders that match its form, clearance angle, tolerance class, fastening method, size and thickness. The rhombic form and cylindrical hole secure the insert in common clamping systems, ensuring repeatable positioning and reduced setup time. The double‑sided design effectively doubles the number of available cutting edges, enabling economical indexation and consistent process stability without altering the toolholder. Reliable chip control for consistent surface quality A double‑sided chipbreaker tailored to the insert geometry promotes stable chip formation and evacuation, which supports consistent surface finish and reduces the risk of built‑up edge when machining rostfreier Stahl. The 1.2 mm corner radius balances edge strength and finish, helping to suppress chatter in rigid setups while delivering satisfactory part dimensional accuracy. Combined with the 4.76 mm thickness, the insert withstands the mechanical demands of typical turning tasks, contributing to fewer rejects and steadier batch outcomes. Practical machining guidance for predictable results For best results with this insert, select feeds and speeds that reflect material characteristics and machine rigidity: favour stable clamping and conservative parameters for interrupted cuts, and exploit the grade’s wear resistance during continuous finishing passes. The CVD coating suits operations where thermal stability and low adhesion are priorities. When integrating into an existing tool system, verify holder compatibility by matching shape, clearance angle (0° in this case) and thickness to ensure secure seating and accurate cutting geometry. For tailored machining recommendations and availability of the Tungaloy DNMG110412 T6215 indexable insert, contact Metav Werkzeuge — our consultants provide application support and can advise on compatible holders and stock levels Technical data Manufacturer article number: 6944673 SKU: 6944673-Tungaloy Manufacturer SKU: TUN6944673 Model series: ISO turning indexable inserts Material: carbide Application: Turning Facts Corner radius: 1.2 mm Insert size: 11 Thickness: 4.76 mm Clearance angle: 0° Insert angle: 55° Special features Grade/coating: CVD‑coated carbide T6215 Chipbreaker: double‑sided Hole: with hole Hole style: cylindrical hole Insert form: rhombic Compatibility: ISO‑standard geometry FAQ What materials is this insert best suited for? The Tungaloy DNMG110412 T6215 insert is optimised for machining rostfreier Stahl and performs well where wear resistance and thermal stability are required. Is the insert reversible and cost‑effective to index? Yes, the double‑sided design of the indexable insert allows multiple tool positions, increasing usable cutting edges and improving cost efficiency before replacement. How is compatibility with toolholders ensured? Compatibility depends on matching the insert’s ISO geometry — shape, clearance angle, tolerance class, fastening method, size and thickness; the DNMG110412 conforms to ISO dimensions for predictable clamping. Can the insert handle interrupted cuts? The T6215 grade is intended for stable to lightly interrupted conditions; for heavy interruptions a more robust setup or alternative grade should be considered. Which edge radius and thickness deliver the best surface quality? The 1.2 mm corner radius combined with the 4.76 mm thickness offers a good compromise between edge strength and surface finish for general turning tasks. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
DNMG 110412 T9215 Wendeplatten - Tungaloy
DNMG 110412 T9215 Wendeplatte zum Drehen von Tungaloy Die DNMG110412 T9215 Wendeplatte ist eine ISO-genormte Schneidplatte für produktives Außen- und Innendrehen bei mittleren Stahlqualitäten ISO-genormte Ausführung für einfache Halterkompatibilität CVD-beschichtetes Hartmetall für hohe Standzeit Für mittlere Stahlbearbeitung und leicht unterbrochene Schnitte Rhombische Platte mit zylindrischem Loch für stabile Befestigung Doppelseitiger Spanbrecher für längere Einsatzzyklen Mehr Leistung durch moderne Schneidstofftechnologie Die Kombination aus CVD-beschichtetem Hartmetall und der Sorte T9215 liefert eine hohe Verschleißfestigkeit bei gleichzeitig guter Bruchsicherheit. Das bedeutet weniger Werkzeugwechsel und mehr Maschinenlaufzeit, was die Produktivität in Serien- und Einzelfertigung spürbar erhöht. Durch die stabile Schneidkante lassen sich gleichbleibende Oberflächenqualitäten erzielen, was Nachbearbeitungsaufwand reduziert und Prozesskosten senkt. Präzise Passform und einfache Integration in den Prozess Dank der ISO-Genormung und der definierten Geometrie mit 55° Winkel und 0° Freiwinkel ist die Platte schnell mit passenden Außenhaltern und Bohrstangen kombinierbar. Die rhombische Form und das zylindrische Loch gewährleisten eine sichere Fixierung; der Eckenradius von 1,2 mm unterstützt robustes Abtragsverhalten. Anwender profitieren von klaren Austauschkriterien und einer einfachen Werkzeugbestückung, was Rüstzeiten reduziert und Prozesssicherheit erhöht. Einsatzgebiet, Auswahlhilfe und Materialhinweis Die Wendeplatte ist speziell für das Drehen von Stahl ausgelegt und empfiehlt sich für kontinuierliche bis leicht unterbrochene Schnitte in mittleren Festigkeiten. Bei der Wahl des Spanbrechers und der Sortenbeschaffenheit sind Werkstoff, Schnittbedingungen und Maschinenstabilität maßgeblich; die Doppel-Seiten-Geometrie bietet Flexibilität beim Umsetzen der Kante. Für Anwender, die auf längere Standzeiten und konstante Ergebnisse abzielen, ist die Sortenwahl T9215 eine wirtschaftliche Option. Für produktive Drehprozesse empfiehlt Tungaloy die Sorte T9215 — kontaktieren Sie Metav Werkzeuge für technische Beratung und Verfügbarkeit unter eMail: info@metav-werkzeuge.com oder Telefon: +49 2822 7131930 Produktmerkmale Artikelnummer: 6772256 Marke: Tungaloy Serie: ISO-Drehwendeschneidplatten Bezeichnung: DNMG110412 Fakten Eckenradius: 1,2 mm Winkel: 55° Freiwinkel: 0° Plattendicke: 4,76 mm Plattengröße: 11 mm Besonderheiten Material: Hartmetall Beschichtung: T9215 (CVD-beschichtet) Schneidstofftyp: CVD-beschichtetes Hartmetall Loch: mit Loch Lochstil: zylindrisches Loch Plattenform: rhombisch Spanbrecher: doppelseitig Anwendung: Drehen Einsatzgebiet: mittlere Stahlbearbeitung Systemaufbau: ISO-Drehplatte, Außenhalter/Bohrstange, Unterlage/Klemmsatz, Ersatzschrauben FAQ Ist die Platte mit gängigen DNMG-Haltern kompatibel? Die DNMG110412 T9215 von Tungaloy ist ISO-genormt und damit grundsätzlich mit Haltern kompatibel, die die entsprechenden Form-, Größen- und Befestigungsdaten unterstützen; bei Unsicherheit die Haltergeometrie prüfen. Für welche Werkstoffe ist die Sorte T9215 geeignet? Die Sorte T9215 ist ausgelegt für mittlere Stahlbearbeitung und verbindet Verschleißwiderstand mit Bruchsicherheit, wodurch sie sich besonders für produktive Serien- und Einzelbearbeitung von Stahl eignet. Wie wirkt sich der Eckenradius auf das Bearbeitungsergebnis aus? Der Eckenradius von 1,2 mm sorgt für robusten Einlauf in den Werkstoff und unterstützt gleichmäßigen Verschleißverlauf; kleinere Radien erzielen feineres Detail, größere Radien erhöhen die Stabilität. Kann die Platte bei leicht unterbrochenen Schnitten verwendet werden? Ja, die DNMG110412 T9215 ist für kontinuierliche bis leicht unterbrochene Schnitte ausgelegt; die Bruchsicherheit der Sorte reduziert das Risiko von Schädigungen bei wechselnden Schnittbedingungen. Welche Vorteile bietet die CVD-Beschichtung konkret? Die CVD-Beschichtung der T9215 sorgt für erhöhte Thermo- und Verschleißfestigkeit, was höhere Schnittgeschwindigkeiten und längere Standzeiten gegenüber unbeschichteten Varianten ermöglicht. Hersteller: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Geschützte Markenzeichen und Warenbezeichnungen liegen im Recht ihrer jeweiligen Eigentümer. Markennamen und geschützte Warenzeichen werden ausschließlich zu Erklärungszwecken genannt. Es besteht keinerlei Verbindung zwischen unserem Unternehmen und den genannten Marken. Es handelt sich bei dem angebotenen Artikel um originale fabrikneue Waren des Herstellers.
DNMG 110412 T9215 Wendeplatten - Tungaloy
Benefit from the combination of CVD-coated carbide (T9215) for high wear resistance and a 1.2 mm nose radius with 55° geometry for stable, precise turning operations; the ISO conformity ensures straightforward holder compatibility and streamlined inventory management. Order the DNMG110412 insert via Metav Werkzeuge or consult our technical advisors for matching holders and chipbreakers. DNMG110412 T9215 turning insert (ISO) — Tungaloy The DNMG110412 T9215 is an ISO‑standard turning insert designed for medium‑steel machining, offering robust wear resistance and good fracture toughness for continuous to lightly interrupted cuts. CVD-coated carbide for wear resistance Rhombic 55° geometry for versatile turning Double-sided chipbreaker for cost efficiency Higher productivity with a CVD-coated cutting grade The combination of T9215 grade and CVD coating provides a balance of wear resistance and fracture toughness, which translates directly into longer tool life and fewer changeovers in series production. For medium‑steel applications this results in steadier cutting conditions and more consistent component quality, reducing scrap rates and increasing uptime. The coating also supports higher cutting speeds where machine and workholding stability permit, improving cycle times without compromising surface finish. Reliable geometry that simplifies holder selection ISO conformity means the insert mates reliably with standard holders when matched by shape, relief angle, tolerance class, fastening method, size and thickness. The rhombic 55° geometry and 1.2 mm nose radius provide a good compromise between strength and finishing capability, while the 0° relief angle and cylindrical hole ensure secure clamping. Choosing the correct double-sided chipbreaker and matching the grade to the workpiece stability results in predictable chip control and a consistent surface quality, even on medium feeds and varied depths of cut. Practical benefits for stock and workshop procedures A reversible, double-sided insert reduces inventory volume and lowers cost per cutting edge compared with single‑edged alternatives. The standardised dimensions — inscribed circle 11 mm, thickness 4.76 mm — make it easy to stock compatible shims, clamps and screws as part of a modular system (insert, external holder or boring bar, shim/clamp and spare fixing screws). This modular approach speeds up service times and makes tool presetting and traceability more efficient on the shop floor, supporting predictable production planning. Contact Metav Werkzeuge for tailored holder recommendations and order matching Tungaloy DNMG110412 inserts with T9215 coating to ensure optimal performance in medium‑steel turning — email info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: 6779346 Manufacturer SKU: TUN6779346 SKU: 6779346-Tungaloy Designation: DNMG110412 T9215 Tungaloy insert Core specifications Nose radius: 1.2 mm Inscribed circle: 11 mm Thickness: 4.76 mm Relief angle: 0° Lead angle: 55° Design & features Model series: ISO turning inserts Material: carbide Coating / grade: T9215 (CVD) Shape: rhombic (DNMG) Hole: with cylindrical hole Chipbreaker: double-sided Application: Turning FAQ What material is this insert designed for? The DNMG110412 T9215 insert is specified as a first choice for medium‑steel machining, combining wear resistance with good fracture toughness for productive turning. How does ISO conformity help with holder selection? Compatibility is ensured when the holder matches the insert’s shape, relief angle, tolerance class, fastening, size and thickness, so ISO‑standard holders and shims fit reliably. Is the T9215 grade suitable for interrupted cuts? Yes — the T9215 (CVD‑coated carbide) offers fracture resistance for continuous to lightly interrupted cuts while maintaining good wear life. Does the insert offer economic advantages for stock management? The insert is double‑sided and reversible, which reduces inventory diversity and lowers cost per usable cutting edge compared with single‑edged alternatives. What are the key dimensions to check before ordering holders? Check the inscribed circle (11 mm), nose radius (1.2 mm), thickness (4.76 mm) and lead angle (55°) to ensure correct holder compatibility. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
DNMG 110412 T9215 Wendeplatten - Tungaloy
Reliable productivity and long tool life result from the combination of a CVD‑coated carbide grade and a robust rhombic geometry; the dual‑sided chipbreaker supports consistent chip control in continuous to lightly interrupted turning. Order the DNMG110412 T9215 insert via Metav Werkzeuge or consult our specialists for application guidance. DNMG110412 T9215 DNMG Turning Insert for Turning – Tungaloy DNMG110412 T9215 is an ISO‑standard indexable turning insert engineered for versatile external and internal turning of medium steels and similar materials. CVD‑coated carbide grade T9215 for long life Dual‑sided chipbreaker for consistent chip control Rhombic 55° geometry for versatile turning operations ISO DNMG form with cylindrical hole and 1.2 mm radius Increase throughput with a wear‑resistant, break‑safe grade The CVD‑coated carbide composition of this insert — identified as T9215 — combines wear resistance with improved breakage resistance, making it a reliable choice for medium‑duty steel turning where productivity matters. The coating reduces flank wear and extends edge life under continuous and lightly interrupted cuts, which leads to longer tool cycles and fewer indexings. Specifying this grade supports a measurable improvement in machining uptime and helps to lower effective tooling costs per component through extended insert life and stable cutting performance. Flexible geometry for precise turning and controlled chips The rhombic form with a 55° geometry and a 1.2 mm corner radius provides a balance between strength and surface finish. The insert’s dual‑sided chipbreaker ensures reliable chip control across a range of feed rates, reducing the risk of built‑up edge and improving swarf management in both external and internal turning applications. The ISO DNMG form and the cylindrical hole make the insert compatible with standard DNMG holders; compatibility is determined by holder form, relief angle, tolerance class, clamping style, size and thickness, allowing straightforward integration into established toolsets. System efficiency, handling and application benefits As part of an indexable system the insert is intended to be used with a matching outside holder or boring bar, a backing shim/clamp set and replacement fastening screws; this modular approach enables rapid index changes and minimal machine downtime. The two usable cutting edges per side offer economical usage, and the medium‑steel focus of the grade makes it suitable for general industrial applications where consistent dimensional results and good surface quality are required. For process planning, the combination of T9215 and appropriate holder geometry supports stable cutting parameters and reproducible performance, improving first‑pass yield and reducing rework. Contact Metav Werkzeuge for tailored recommendations on integrating the Tungaloy T9215 grade into production and to secure original inserts for immediate delivery. Technical data Article number: 6966174 SKU: 6966174-Tungaloy Manufacturer SKU: TUN6966174 Model series: ISO‑Drehwendeschneidplatten Article name: DNMG110412 T9215 Tungaloy indexable insert Core specifications Size: 11 mm Thickness: 4.76 mm Corner radius: 1.2 mm Geometry angle: 55° Clearance angle: 0° Design & special features Material: carbide Coating/grade: CVD‑coated, T9215 Shape: rhombic (DNMG) Hole: cylindrical hole Chipbreaker: dual‑sided Application: turning (external and internal) Compatibility: ISO DNMG holders, backing shim/clamp systems FAQ What materials is this insert designed to machine? The Tungaloy DNMG110412 T9215 insert is optimised for medium‑strength steels and similar materials, performing well under continuous and lightly interrupted cuts thanks to its CVD‑coated carbide grade. Which geometry and dimensions does the insert offer? The insert features a rhombic DNMG form with a 55° main geometry, a 1.2 mm corner radius and a plate thickness of 4.76 mm; it includes a cylindrical hole for standard ISO DNMG clamping systems. Is the insert reversible and suitable for indexing? Yes — the insert is dual‑sided and indexable, offering two usable edges per side; its design supports quick indexing to reduce machine downtime. How does the chipbreaker perform across different turning tasks? The dual‑sided chipbreaker on this insert ensures consistent chip control across a variety of feeds and depths, improving swarf management and reducing the likelihood of built‑up edge during typical turning operations. Can the insert be used for internal boring as well as external turning? Provided the holder geometry and clearance are suitable, the DNMG110412 T9215 insert is compatible with internal boring applications as well as external turning, offering flexibility within an ISO‑based tooling system. Manufacturer/Responsible: Tungaloy‑NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand‑new product from the manufacturer.
DNMG 110412 T9215 Wendeplatten - Tungaloy
Take advantage of the combination of CVD-coated carbide and a 55° rhombic geometry with a 1.2 mm corner radius to achieve consistent productivity in medium steel turning; order the insert directly via Metav Werkzeuge or consult the technical team for compatibility and stock information. DNMG110412 T9215 DNMG 110412 turning insert by Tungaloy — CVD-coated carbide, 55° rhombic The DNMG110412 T9215 is an ISO rhombic turning insert engineered for reliable external and internal turning, optimised for medium steel machining. CVD-coated carbide for high wear resistance Designed for medium steel machining 55° rhombic geometry with 1.2 mm radius Double-sided insert; cylindrical hole for secure fit Proven performance for productive turning The CVD-coated carbide grade T9215 provides a balance of wear resistance and fracture toughness that favours uninterrupted production runs. As an ISO rhombic indexable insert, this turning solution reduces tool changes compared with edge-style tooling while delivering repeatable results. The combination of coating and substrate allows for higher cutting speeds under stable conditions, which translates directly into improved cycle times and lower cost per part. The specification emphasises predictable wear behaviour and a robust cutting edge for mid-range steel alloys. Secure fit and geometry that supports machining stability The 55° rhombic geometry and 1.2 mm corner radius are selected to provide a compromise between edge strength and surface finish. The insert is double-sided, featuring a cylindrical hole for positive location in compatible holders; compatibility is determined by form, clearance angle, tolerance class, clamping method, size and thickness. With a 0° clearance angle and a standard ISO designation, the insert suits common external and internal turning set-ups where stable clamping and repeatability are priorities. This geometry helps to control cutting forces and vibration, supporting a more consistent surface quality. Coating and substrate benefits explained The insert’s CVD coating forms a hard, wear-resistant layer that improves abrasion resistance and thermal stability at the cutting edge. Beneath the coating, the carbide substrate absorbs shock and resists chipping, enhancing service life during continuous and lightly interrupted cuts. For medium steel applications, this pairing ensures effective chip formation and manageable heat distribution, reducing the need for frequent index changes and maintaining component tolerances across batches. The result is reliable tool life and consistent dimensional accuracy. Application advice for efficient integration Designed for turning operations, this insert performs best when matched to a suitable external holder or boring bar and supported by a stable machine set-up. Choosing the appropriate chipbreaker and grade to match workpiece material and cutting strategy will further optimise productivity. Where process security and repeatability matter, the insert’s ISO conformity simplifies tool selection and inventory management. For production-focused environments, the insert contributes to fewer interruptions, predictable maintenance intervals and a smoother overall workflow. Contact Metav Werkzeuge for availability and advice on integrating this Tungaloy turning insert into production setups Technical Data Article number: 6772234 Manufacturer SKU: TUN6772234 SKU: 6772234-Tungaloy Model series: ISO-Drehwendeschneidplatten Designation: DNMG110412 Material: carbide Facts Geometry angle: 55° Corner radius: 1.2 mm Clearance angle: 0° Plate thickness: 4.76 Size designation: 11 Special features Grade: T9215 Coating: CVD-coated carbide Plate form: rhombic Chipbreaker: double-sided Hole: with hole (cylindrical hole) Typical application: external and internal turning System components: ISO insert, matching external holder or boring bar, support/clamp set and spare screw FAQ What materials is this insert best suited for? The DNMG110412 T9215 insert is specified for medium steel machining; the T9215 CVD-coated carbide grade combines wear resistance and toughness for this material class. How does the T9215 coating affect tool life? The CVD-coated carbide surface of the Tungaloy DNMG110412 reduces abrasive wear and helps maintain edge integrity, extending effective tool life during continuous and lightly interrupted cuts. Is this insert reversible or indexable on both sides? Yes, the insert is double-sided, allowing indexing to a fresh cutting edge and offering a cost-effective use of available cutting edges. Which geometry and corner radius does the insert have? This ISO rhombic insert uses a 55° geometry with a 1.2 mm corner radius, balancing edge strength and achievable surface finish for turning operations. What should be considered when selecting a holder for this insert? Holder compatibility depends on insert form, clearance angle, tolerance class, clamping method, size and thickness; ensure the external holder or boring bar matches the ISO designation DNMG110412 to secure correct fit and repeatability. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
DNMG 110412 T9215 Wendeplatten - Tungaloy
Take advantage of the CVD-coated T9215 grade for high wear resistance and reliable edge strength, combined with the economical double-sided DNMG geometry for steady production flow. Order directly via Metav Werkzeuge or request application advice from our consultants. DNMG110412 T9215 — Tungaloy ISO turning insert for medium-steel turning, rhombic 55° A DNMG110412 T9215 ISO-standard indexable insert designed for external and internal turning; CVD-coated cemented carbide, rhombic 55° geometry with cylindrical hole and double-sided cutting edges for productive, repeatable metal removal. CVD-coated cemented carbide T9215 Ideal for medium-steel machining Rhombic 55° geometry, double-sided Cylindrical hole for secure clamping Optimised wear resistance and steady productivity The CVD-coated T9215 grade combines high wear resistance with good fracture toughness, making it well suited to the demands of medium-steel turning under continuous to lightly interrupted cuts. The rhombic 55° geometry offers a balance between cutting-edge strength and accessibility for finishing and semi-finish operations. Using a double-sided insert increases the number of usable cutting edges and reduces tool-change frequency, which translates into more productive machining cycles and lower tooling cost per part. Where material compatibility and process stability are prioritised, this grade delivers consistent results. Compatibility and secure clamping for reliable set-up Insert-to-holder compatibility depends on geometry, clearance angle, tolerance class, clamping method, size and thickness; the ISO designation ensures interchangeability across standard toolholders. The cylindrical hole and matching screw/clamp arrangement provide positive seating and repeatable positioning in the seat, reducing setup variation. The rhombic profile with a 55° included angle also allows access to a wide range of turning tasks while maintaining edge security. For economical workshop operation, choosing a matching chipbreaker and the correct insert size preserves surface finish and extends edge life. Practical selection and machining guidance Select the chipbreaker and grade according to workpiece material, cutting conditions and machine stability: the T9215 grade is the first choice for general medium-steel applications thanks to its stable chip formation and robust edge. In less stable set-ups, reduce feed or choose a sturdier chipbreaker; for fine finishing, a lighter depth of cut and the same grade can still achieve improved surface quality. The ISO system simplifies inventory management—keeping a small range of standard sizes and chipbreakers covers many applications while supporting high uptime and consistent component quality. For material-specific advice and to confirm holder compatibility for Tungaloy turning inserts, contact Metav Werkzeuge for application support and ordering at info@metav-werkzeuge.com or call +49 2822 7131930 Technical Data Article number: 6772213 Manufacturer SKU: TUN6772213 Type designation: DNMG110412 Model series: ISO turning inserts Material: cemented carbide Facts Grade/coating: T9215 (CVD-coated) Size: 11 mm Corner radius: 1.2 mm Relief (clearance) angle: 0° Edge angle: 55° Special features Rhombic plate form Double-sided insert Cylindrical hole for clamping ISO-standard indexable insert Suitable for external and internal turning Recommended for medium-steel machining; continuous to lightly interrupted cuts FAQ What materials is this insert recommended for? The DNMG110412 T9215 Tungaloy turning insert is recommended primarily for medium-steel machining; the T9215 grade balances wear resistance and toughness for productive steel turning. Is the insert compatible with standard ISO holders? Yes — the ISO designation DNMG110412 indicates compatibility with ISO-standard holders, provided form, clearance angle, tolerance class, clamping method, size and thickness match the toolholder. How many usable edges does the insert offer? This is a double-sided DNMG indexable insert, which provides multiple cutting edges per indexable seat and improves cost-efficiency in repetitive turning tasks. Can the insert be used for interrupted cuts? The T9215 grade is suitable for continuous to light interruptions; for heavy interruptions, select a chipbreaker and cutting parameters focused on enhanced edge security. Which chipbreaker should be chosen for better surface finish? Choose a chipbreaker matched to the workpiece material and the desired finish; pairing the correct chipbreaker with the T9215 grade helps control chips and improves surface quality while maintaining tool life. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
DNMG 110412 T9225 Wendeplatten - Tungaloy
Benefit from the combination of a CVD‑coated carbide T9225 grade and proven ISO compatibility to achieve productive medium‑to‑heavy turning with reliable chip control; order the DNMG110412 insert directly via Metav Werkzeuge or consult the technical advisers if required. DNMG 110412 T9225 — Tungaloy indexable turning insert (CVD‑coated carbide, 55°) DNMG110412 T9225 is an ISO‑specified, rhombic indexable insert designed for robust external and internal turning in varied steel applications Rhombic DNMG geometry, 55° approach angle CVD‑coated carbide grade T9225 for steel Double‑sided chipbreaker, versatile cutting Compatible with standard ISO holders Improved productivity for medium‑to‑heavy steel turning The CVD‑coated T9225 grade delivers a balance of toughness and wear resistance tailored for medium‑to‑heavy steel machining where changing engagement conditions or slightly interrupted cuts require additional edge strength. The coating provides a hard, temperature‑resistant surface while the carbide substrate maintains core toughness; this combination reduces flank wear and extends tool life under demanding operating parameters. As an ISO‑formed indexable insert, the geometry and coating together enable stable cut formation and consistent surface finish with fewer tool changes. Secure mounting and universal ISO compatibility The rhombic DNMG geometry with a 55° approach angle and a cylindrical locating hole ensures precise positioning and reliable clamping in standard ISO external holders or boring bars. The 0° clearance specification and the specified plate thickness support repeatable set‑ups and predictable cutting forces, which cuts down on secondary adjustments and machine downtime. The reversible, double‑sided design allows economical use of both cutting edges before replacement, enhancing uptime and simplifying inventory management for production workshops. Confidence in chip control and process stability Equipped with a double‑sided chipbreaker, the insert promotes stable chip formation across a range of feeds and depths of cut, helping to avoid built‑up edge and reducing the risk of surface damage. The moderate corner radius supports finishing and semi‑roughing passes while preserving edge strength for interrupted cuts. Backed by Tungaloy’s material and coating expertise, this insert suits manufacturers seeking a blend of durability and consistent performance under variable cutting conditions, contributing to predictable cycle times and fewer unexpected interventions. Contact Metav Werkzeuge today to review suitability for specific steel grades and machining parameters for the Tungaloy DNMG110412 T9225 indexable insert; technical advisers are available at info@metav-werkzeuge.com or by phone on +49 2822 7131930 Technical data Manufacturer article number: 6780629 SKU: 6780629-Tungaloy Model series: ISO‑turning inserts Grade: T9225 Cutting material: CVD‑coated carbide Facts Insert designation: DNMG110412 Geometry: DNMG, 55° Size: 11 mm Thickness: 4.76 mm Corner radius: 1.2 mm Clearance angle: 0° Hole: with cylindrical hole Special features Rhombic shape with double‑sided chipbreaker Suited for medium to heavy steel turning Reversible, indexable insert for economical use Compatible with standard ISO holders for secure clamping FAQ What materials is this insert suitable for? The Tungaloy DNMG110412 T9225 insert is engineered primarily for steel machining, offering good performance in medium‑to‑heavy turning where increased toughness is required. Can the insert handle interrupted cuts? Yes. The T9225 grade combines a tough carbide substrate with a CVD coating, providing the necessary edge strength and resilience for slightly interrupted cuts. How does the chipbreaker affect performance? The double‑sided chipbreaker promotes controlled chip formation and evacuation, improving surface finish and reducing the risk of chip entanglement during continuous and semi‑continuous turning. Is the insert reversible and how many cutting edges are available? The DNMG geometry is double‑sided and reversible, offering two usable cutting edges per side depending on the holder and orientation, which supports cost‑effective tool usage. What determines compatibility with a toolholder? Compatibility is given by the ISO form, relief angle, tolerance class, fastening method, insert size and thickness; the DNMG110412 designation ensures conformity with standard DNMG holders. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand‑new product from the manufacturer.
DNMG 110412 T9225 Wendeplatten - Tungaloy
Achieve reliable productivity with the T9225 grade and CVD-coated carbide construction, engineered for medium to heavy steel turning and for handling mildly interrupted cuts. Order the DNMG110412 T9225 insert directly via Metav Werkzeuge or consult our specialists for tailored application guidance. DNMG110412 T9225 — ISO rhombic turning insert for medium to heavy steel turning, Tungaloy DNMG110412 T9225 is an ISO-standard rhombic turning insert designed for robust general-purpose machining where varied engagement conditions demand toughness alongside wear resistance. Robust CVD-coated grade T9225 Designed for medium to heavy steel turning Double-sided chipbreaker for stable chips ISO rhombic form with cylindrical hole Consistent productivity under variable cutting conditions The CVD-coated carbide composition and the T9225 grade deliver a balance of hardness and toughness that supports sustained machining performance. This indexable component promotes stable chip formation even under slightly interrupted cuts, reducing unplanned downtime and helping to maintain spindle load consistency. The robust coating improves surface contact resistance, which contributes to extended tool life and predictable wear patterns during batch production. Simple adaptation to existing tool systems Compatibility with a holder is determined by form, relief angle, tolerance class, fastening method, size and thickness; the rhombic geometry with a cylindrical hole ensures secure clamping in standard ISO tool holders. The insert’s 55° approach angle and 4.76 mm plate thickness make it suitable for a broad range of external and internal turning operations. These characteristics make integration straightforward for maintenance teams and metrology-aware production planners seeking a drop-in replacement without complex fixture changes. Process reliability through engineered chip control The double-sided chipbreaker supports repeatable chip segmentation, reducing the risk of long, entangling swarf and minimising finishing interruptions. For turning operations on steel where chip evacuation and surface finish matter, this insert offers tangible gains in cycle-time consistency. The geometry and chipbreaker combination also reduce the incidence of built-up edge, so downstream inspection and handling benefit from fewer scratched surfaces and less rework. Optimised for medium to heavy steel turning applications As a universal grade intended for robust conditions, this insert is particularly effective where cutting parameters vary or where intermittent engagement is expected. The indexable insert design allows four usable edges per seat, improving cost-efficiency in production runs. Selecting the correct chipbreaker and adapting feed/speed to the material hardness will yield the best compromise between cutting performance and component quality. Contact Metav Werkzeuge for application-specific recommendations and stock availability of the Tungaloy DNMG110412 T9225 turning insert; our technical team can advise on holder compatibility, cutting data and optimal chipbreaker selection. Technical data Article number: 6966175 Manufacturer SKU: TUN6966175 Model series: ISO-Drehwendeschneidplatten Product designation: DNMG110412 T9225 Tungaloy insert Cutting material: CVD-coated carbide Facts Corner radius: 1.2 mm Approach angle: 55° Relief angle: 0° Plate thickness: 4.76 mm Plate size: 11 Special features Rhombic plate form Cylindrical hole style Double-sided chipbreaker Suitable for external and internal turning Universal grade for medium to heavy steel turning Compatible with standard ISO holders (form/tolerance/fastening dependent) FAQ What materials is this insert intended for? The DNMG110412 T9225 insert is optimised for medium to heavy steel turning; the T9225 grade offers toughness for variable engagement and mildly interrupted cuts. Can the insert be used for interrupted cuts? Yes, the CVD-coated T9225 grade and reinforced edge geometry make this insert suitable for light to moderate interruptions in turning operations. How many cutting edges are available per insert? The rhombic indexable design provides multiple usable edges; rotating to a fresh edge extends operational life before replacement is required. Which holder characteristics determine compatibility? Compatibility depends on insert form, relief angle, tolerance class, fastening, size and thickness; ensure the holder matches DNMG110412 dimensions and clamping style. Does the chipbreaker support consistent swarf control? The double-sided chipbreaker is designed to produce segmented chips, improving chip evacuation and reducing finishing issues. Is this an original Tungaloy product? Yes, this article is an original, brand-new Tungaloy turning insert and carries the manufacturer’s grade and specifications. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
DNMG 110412 T9225 Wendeplatten - Tungaloy
Benefit from the combination of CVD-coated carbide T9225, a 55° rhombic geometry and a double-sided chipbreaker for steady performance in medium-to-heavy Stahl turning; order the insert directly via Metav Werkzeuge or consult our technical team for application support. DNMG110412 T9225 — DNMG indexable turning insert, CVD-coated carbide, 55° geometry | Tungaloy A DNMG110412 T9225 indexable insert designed for external and internal turning, offering a robust CVD-coated carbide grade for interrupted cuts and variable engagement conditions. CVD-coated carbide grade T9225 ISO-standard DNMG 110412 designation Double-sided chipbreaker for versatility Rhombic 55° geometry for general turning Corner radius 1.2 mm for strength Reliable material and long tool life for stable production The CVD-coated carbide T9225 is formulated to combine robust toughness with wear resistance, making it suitable for medium-to-heavy Stahl machining where varying cut conditions and light interruptions occur. The insert’s substrate and coating promote consistent performance across a wide range of alloyed and non-alloyed materials, reducing the frequency of tool changes and contributing to predictable cycle times. This stability supports higher effective uptime and simplifies process planning on conventional and CNC lathes. Clear compatibility and mounting criteria for safe toolholding Compatibility with a toolholder is determined by the insert’s geometry, relief angle 0°, tolerance class, clamping method, size and thickness. The rhombic shape with a 55° geometry and a cylindrical hole ensures secure locating in appropriately designed DNMG holders and boring bars. Where repeatability and clamping repeatability are required, matching the ISO designation and the insert thickness of 4.76 mm with the holder seat and screw/klemmsatz is essential. Correct pairing reduces chatter, improves surface finish and extends the effective edge life. Productivity gains through geometry and chip control The double-sided chipbreaker design provides predictable chip formation and evacuation in a variety of feeds and depths of cut, while the corner radius 1.2 mm balances edge strength with achievable surface finish. For shops aiming to raise throughput, the combination of a standard ISO indexable system and a universally oriented chip control concept reduces set-up complexity and allows fast index changes. The result is a pragmatic route to improved machining economy and lower per-component tooling cost in batch production. For robust medium-to-heavy Stahl turning with proven durability, request the Tungaloy DNMG110412 T9225 insert from Metav Werkzeuge or contact our advisers at info@metav-werkzeuge.com or +49 2822 7131930 to discuss application fitting and stock availability Technical data Article number: 6780634 SKU: 6780634-Tungaloy Manufacturer SKU: TUN6780634 Model series: ISO turning indexable inserts Label: DNMG110412 T9225 Tungaloy insert Numbers / Core technical data Corner radius: 1.2 mm Relief angle: 0° Lead/approach angle: 55° Thickness: 4.76 mm Size designation: 11 Designs / Special features Carbide base, CVD-coated (T9225) Rhombic geometry (DNMG) Double-sided chipbreaker Cylindrical locating hole ISO compatibility for external and internal turning Intended for medium-to-heavy Stahl machining FAQ What materials is this insert suitable for? The DNMG110412 T9225 insert from Tungaloy is intended primarily for medium-to-heavy Stahl machining and performs well where higher toughness is required for interrupted cuts. Is the insert reversible and indexable? Yes, the insert is double-sided and indexable; both sides offer cutting edges to be indexed when one edge is worn. Which geometry and relief angle does the insert have? The insert uses a rhombic DNMG form with a 55° approach geometry and a 0° relief angle designed for secure seating in compatible holders. How does the T9225 coating affect performance? The CVD-coated T9225 grade enhances wear resistance while maintaining edge toughness, improving life in mixed and interrupted cutting conditions. What specifications are important when selecting a holder? Match the ISO DNMG110412 designation, thickness (4.76 mm), size and the cylindrical hole/clamping arrangement to ensure proper seating and repeatable clamping. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
Fragen zu diesen Produkten??
Mit mehr als 30 Jahren Erfahrung beraten wir Sie gerne persönlich.
Tel.: +49 2822 7131930
Mail: info@metav-werkzeuge.com