RCMT 10T3M0 AH8005 Wendeplatten - Tungaloy
The combination of PVD-coated carbide in grade AH8005 and an RS chipbreaker delivers wear resistance and stable chip control for turning of heat-resistant alloys and hard materials; order the insert directly via Metav Werkzeuge or consult the advisers if required. RCMT10T3M0-RS AH8005 — RCMT indexable turning insert (ISO 10T3M0), PVD-coated (Tungaloy) RCMT10T3M0-RS AH8005 is an ISO-form indexable insert designed for external and internal turning of heat-resistant alloys and other hard materials, providing durable cutting performance in stable setups. RCMT 10T3M0 form, ISO standard PVD-coated carbide grade AH8005 RS chipbreaker for stable chip control Cylindrical hole with 40°–60° countersink Reliable machining of heat‑resistant alloys and hard materials The insert combines a PVD-coated surface with a wear‑resistant carbide substrate to extend tool life under elevated temperatures. The AH8005 grade is formulated for cutting heat‑resistant alloys and hardened workpieces, reducing flank wear and maintaining edge integrity during continuous turning. For production environments where predictable tool life reduces downtime, the insert supports consistent cycle times and fewer tool changes. The coating also improves adhesion resistance, which helps when machining materials prone to built‑up edge. Improved productivity through controlled chips and stable cutting Equipped with the RS chipbreaker, this indexable insert promotes short, controllable chips in a range of feed and depth combinations, which lowers the risk of entanglement and reduces secondary finishing work. Stable chip formation contributes to better surface finish and fewer interruptions during runs, translating into higher productive throughput and a lower cost per component. Where process reliability matters, the chip control feature helps maintain momentum on batch and single‑piece flow. Fast setup and secure clamping in ISO systems The insert conforms to the ISO 10T3M0 designation and the round RCMT geometry, ensuring compatibility with standard holders when form, rake, tolerance and thickness match the toolholder specification. A cylindrical hole with a single‑sided countersink (40°–60°) permits secure fastening using the appropriate clamp and screw set, while the 7° rake angle supports stable cutting in many turning configurations. Clear adherence to ISO sizing simplifies tool inventory and shortens changeover times in workshops and production cells. Application focus and handling recommendations Designed primarily for turning, both external and internal, the insert performs best in stable setups where toolholder rigidity and correct nose radius selection are ensured. The 3.97 mm plate thickness and 10 mm round size balance edge support and accessibility in confined geometries. For best results, match the RS chipbreaker and AH8005 grade to the workpiece alloy and cutting parameters; this combination is optimised for process security and repeatable finishing quality in demanding materials. Contact Metav Werkzeuge for availability, cutting data and application advice: info@metav-werkzeuge.com | +49 2822 7131930 — technical consultants are available to recommend the correct insert and clamping solution Technical data Article number: 6747782 Manufacturer SKU: TUN6747782 Brand: Tungaloy Type designation: RCMT10T3M0-RS AH8005 Model series: ISO indexable turning inserts Numbers / Core technical data Size: 10 mm Thickness: 3.97 mm Rake angle: 7° Manufacturer article number: 6747782 Special features PVD-coated carbide (wear‑resistant) Chipbreaker: RS Hole: cylindrical hole with single‑sided countersink (40°–60°) Insert shape: round (RCMT) Application: turning (external and internal) FAQ What materials is this insert best suited for? The RCMT10T3M0-RS AH8005 insert from Tungaloy is engineered for heat‑resistant alloys and other hard materials; the PVD-coated AH8005 grade improves wear resistance under elevated cutting temperatures. How does the RS chipbreaker affect machining? The RS chipbreaker on the RCMT indexable insert produces short, controlled chips that reduce coolant interruptions and improve surface finish, aiding uninterrupted production runs. Is the insert compatible with standard ISO holders? Yes; the RCMT10T3M0 form follows ISO sizing and, provided the holder matches form, rake, tolerance, size and thickness, the insert will fit standard turning toolholders and clamping systems. What are the key dimensional features to check for mounting? Confirm the 10 mm round size, 3.97 mm thickness, the cylindrical hole with 40°–60° countersink, and the 7° rake angle to ensure correct seating and secure clamping in the chosen holder. Can this insert be used for both external and internal turning? The RCMT10T3M0-RS AH8005 insert is suitable for both external and internal turning when paired with a matching holder and appropriate machining parameters for the workpiece material. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
RCMT 10T3M0 AH8015 Wendeplatten - Tungaloy
Take advantage of the balanced combination of PVD-coated AH8015 carbide and ISO-standard geometry for reliable turning of heat-resistant alloys; compatibility with holders is ensured by standardised form and fastening. Order the inserts directly via Metav Werkzeuge or consult our specialists for process-specific recommendations. RCMT10T3M0-RS AH8015 indexable turning insert, PVD-coated, for turning — Tungaloy The RCMT10T3M0-RS AH8015 is an ISO-standard indexable insert designed for general turning of heat-resistant alloys, offering a balanced mix of wear resistance and cutting-edge stability. PVD-coated carbide grade AH8015 ISO RCMT geometry for standard holders Round 10 mm form with cylindrical hole 7° clearance angle for secure cutting Consistent performance on heat-resistant alloys The PVD-coated AH8015 grade supplies a measured balance between wear resistance and cutting-edge stability, making it particularly suitable for machining heat-resistant alloys where thermal and mechanical loads vary. The coating reduces adhesion and thermal softening at the cutting edge, so tool life is extended and process windows are wider. This results in fewer insert changes and more predictable batch quality, which benefits production planning and cost efficiency. Secure integration with standard toolholders Compatibility with holders is defined by the insert’s geometry — form, 7° clearance, tolerance class, fastening method, size and thickness — which ensures the insert seats and clamps reliably in established systems. The round 10 mm form with a cylindrical hole and single-sided countersink (40°–60°) enables straightforward clamping in compatible external holders or boring bars. Specified dimensions and the ISO code support rapid replacement and interchangeability within existing tooling setups. Process advantages: stable edges and chip control The RS chipbreaker geometry combined with the AH8015 composition promotes stable chip formation across varied turning operations. For external and internal turning, choosing the correct chipbreaker and grade relative to material and rigidity reduces vibration and improves surface finish. The insert’s thickness and corner design contribute to edge strength, meaning fewer unexpected tool failures and more consistent component tolerances in serial production. Contact Metav Werkzeuge for tailored process advice and to order Tungaloy RCMT10T3M0-RS AH8015 turning inserts directly via info@metav-werkzeuge.com or by phone on +49 2822 7131930 Technical data Article number: 6747783 SKU: 6747783-Tungaloy Manufacturer article number: TUN6747783 Designation: RCMT10T3M0-RS AH8015 Tungaloy insert Material: cemented carbide Coating: PVD (AH8015) Chipbreaker: RS Core specifications Plate size: 10 mm Plate thickness: 3.97 mm Clearance angle: 7° Corner radius: 0 mm ISO code: 10T3M0 Special features Round plate form With cylindrical hole + single-sided countersink (40°–60°) ISO-standard turning insert Suited for machining heat-resistant alloys Balanced wear resistance and edge stability FAQ What materials is this insert intended for? The RCMT10T3M0-RS AH8015 insert from Tungaloy is specified for the general machining of heat-resistant alloys and performs well where a balance of wear resistance and edge stability is required. How does the AH8015 grade affect performance? AH8015 is a PVD-coated carbide grade that improves thermal resistance and reduces edge wear, resulting in longer tool life and more consistent surface quality when machining demanding alloys. Is the insert compatible with standard RCMT holders? Yes — the insert adheres to ISO RCMT geometry; compatibility is ensured by matching form, 7° clearance, tolerance class, fastening method, size and thickness to the holder. What is the chip control solution on this insert? The RS chipbreaker promotes controlled chip formation during turning operations, helping to maintain surface finish and reduce the risk of built-up edge under varying cutting conditions. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
RCMT 10T3M0 AH905 Wendeplatten - Tungaloy
Benefit from a highly wear-resistant, PVD-coated AH905 grade combined with a precise RS chipbreaker and ISO compatibility to keep turning operations stable and economical. Order the insert or request application guidance directly via Metav Werkzeuge for tailored machining advice. RCMT 10T3M0 AH905 Tungaloy turning insert — PVD-coated cemented carbide, RS chipbreaker RCMT 10T3M0 AH905 is a compact ISO-standard indexable insert engineered for reliable external and internal turning with secure clamping and consistent edge performance PVD-coated AH905 grade for long life RS chipbreaker for controlled chip formation ISO-standard form for broad holder compatibility 10 mm size, 3.97 mm thickness, 7° free angle Stable cutting edge for secure process control The insert is manufactured from cemented carbide with a PVD-coated AH905 grade, delivering a balance of wear resistance and toughness. This combination preserves a sharp cutting edge even under intermittent cutting or mixed cutting conditions, which reduces edge chipping and maintains a predictable tool life. For production environments where process security is critical, the coated substrate minimises rework and supports repeatable part quality across batches. ISO compatibility that simplifies setup and reduces downtime Designed as an ISO-standard turning insert, the geometry and tolerances match common external holders and boring bars. The 10 mm inscribed circle and 3.97 mm thickness ensure dimensional fit, while the 7° free angle helps maintain cutting clearance for turning operations. The insert is supplied with a cylindrical hole plus single-side countersink (40°–60°) to suit standard clamping screws and seats, reducing setup variability and helping achieve repeatable seating and orientation. Controlled chip flow and surface finish for predictable results The RS chipbreaker has been chosen to manage chip formation reliably during both external and internal turning. Controlled chips reduce the risk of workpiece damage and tool interference, and promote consistent surface quality. Where a sharp edge and stable cutting performance are required, this chip geometry supports gentle chip evacuation and dependable finishing, enabling longer uninterrupted cycles and fewer interventions on the machine. System approach for productive machining and easy replacement The insert is intended to be used as part of a system: the ISO insert together with a compatible outer holder or boring bar, a suitable clamping plate or clamp set and standard replacement screws. This modular approach allows rapid exchange and straightforward inventory management. If further machining data is required — cutting parameters, recommended feeds, or compatible holders — Metav Werkzeuge can supply detailed guidance to match the AH905 grade and RS chipbreaker to the specific operation. For specific application advice or to secure the RCMT10T3M0-RS AH905 Tungaloy insert, contact Metav Werkzeuge for availability and machining recommendations via info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: 6879350 Manufacturer SKU: TUN6879350 SKU: 6879350-Tungaloy Model series: ISO-turning inserts ISO designation: RCMT10T3M0-RS Shape: round Dimensions and geometry Inscribed circle: 10 mm Thickness: 3.97 mm Free angle: 7° Corner radius: 0 mm Hole: with hole Countersink angle: 40°–60° Materials and features Coating: PVD Grade: AH905 Substrate: cemented carbide Chipbreaker: RS Application: turning System: compatible with ISO holders and standard clamping sets FAQ Which machining operations suit this insert best? The RCMT10T3M0-RS AH905 Tungaloy insert is designed primarily for external and internal turning where a sharp edge and high process reliability are required. How does the AH905 grade benefit production runs? AH905 PVD-coated grade offers enhanced wear resistance and edge stability, which helps to extend tool life and reduce unplanned stoppages during medium- to high-volume turning with the RCMT10T3M0-RS configuration. What does the RS chipbreaker deliver? The RS chipbreaker on this insert promotes controlled chip formation and evacuation, improving surface finish and lowering the risk of chip-related interruptions in turning operations. Can the insert be used in standard ISO holders? Yes—the insert follows ISO geometry and mounting features; compatibility depends on holder form, free angle, tolerance class, fastening, size and thickness, so matching those parameters is essential. Are there special mounting features to note? The insert is supplied with a cylindrical hole and a single-side countersink (40°–60°); correct clamping and seat condition are important for secure fastening and repeatable performance. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
RCMT 10T3M0 T9215 Wendeplatten - Tungaloy
Take advantage of the combination of high wear resistance, stable chip control, and ISO-compliant dimensions for consistent productivity in turning operations; order the inserts directly via Metav Werkzeuge or ask the consultants for application-specific advice. RCMT 10T3M0 T9215 – ISO turning insert, CVD-coated cemented carbide (Tungaloy) A RCMT 10T3M0 T9215 indexable insert designed for ISO-compliant external and internal turning, with a 7° clearance angle and an RS chipbreaker for medium steel machining CVD-coated cemented carbide grade T9215 Round 10 mm insert, 3.97 mm thickness 7° clearance angle for stable cutting Cylindrical hole with single-sided countersink 40°–60° Increase throughput with a wear-resistant grade The T9215 grade is a CVD-coated cemented carbide developed for medium steel applications, combining high wear resistance with fracture toughness to support long tool life under continuous and slightly interrupted cuts. As a result, machining cycles benefit from fewer insert changes and a higher effective spindle utilisation, which translates into measurable productivity gains on batch and single-piece runs. The carbide composition and coating deliver consistent edge stability, reducing rework and stabilising surface finish across runs. Precise fit and repeatable clamping for reliable results Compatibility with a toolholder is determined by form, clearance angle (7°), tolerance class, fastening, size and thickness; selecting a matching holder ensures correct seating and clamping force. The round 10 mm format and 3.97 mm thickness allow simple indexability and symmetrical wear distribution; the central hole with a single-sided countersink (40°–60°) supports secure fixation while easing orientation during changeovers. Clear specification adherence reduces setup time and minimises the risk of incorrect mounting. Controlled chip formation for safer machining The RS chipbreaker is optimised for stable chip control when turning medium steels, promoting predictable chip flow and preventing entanglement at the cut. Predictable chip behaviour improves surface quality and reduces downtime caused by manual chip clearing. In combination with the CVD coating, the chipbreaker helps maintain a sharp cutting edge for longer, which is particularly beneficial during longer production runs or higher feed rates where thermal and mechanical loads are elevated. Practical advantages for workshop integration The ISO-series design aids selection and inventory management by matching established industry standards for insert shape and mounting. The insert is intended for use in an ISO turning insert system consisting of the indexable insert itself, a compatible external holder or boring bar, a clamp or support shim and replacement screws. This modular approach simplifies procurement and reduces the variety of spare parts required, enabling a streamlined tool supply and faster changeovers at the machine. Contact Metav Werkzeuge for tailored application support on Tungaloy turning inserts; technical advice and ordering assistance are available by e‑mail at info@metav-werkzeuge.com or by phone on +49 2822 7131930 Technical Data Article number: 6772457 SKU: 6772457-Tungaloy Manufacturer SKU: TUN6772457 Model series: ISO-Drehwendeschneidplatten ISO designation: RCMT10T3M0-RS Core specifications Insert size: 10 mm Thickness: 3.97 mm Relief/clearance angle: 7° Corner radius: 0 mm ISO code: 10T3M0 Features & materials Grade / coating: T9215 (CVD-coated cemented carbide) Material: cemented carbide Chipbreaker: RS Hole style: cylindrical hole + single-sided countersink (40°–60°) Shape: round Application: turning (external and internal) Compatibility determined by form, clearance angle, tolerance class, fastening, size and thickness FAQ What materials is this insert best suited for? The RCMT 10T3M0 T9215 insert is optimised for medium steel machining; the T9215 grade combines wear resistance and toughness for productive turning of such materials. Can this insert be used for interrupted cuts? Yes, the CVD-coated cemented carbide grade provides fracture resistance suitable for continuous to slightly interrupted cuts; heavy interruptions may require a different grade or geometry. How does the RS chipbreaker affect surface finish? The RS chipbreaker promotes controlled chip flow and reduces built-up edge tendency, helping to maintain a consistent surface finish during standard turning operations. Which holder features are required for correct compatibility? Compatibility depends on matching the insert form, 7° clearance angle, tolerance class, fastening method, size (10 mm) and thickness (3.97 mm) to the holder or boring bar. Is the central hole suitable for secure clamping? Yes, the insert’s cylindrical hole with a single-sided countersink (40°–60°) ensures secure fixation and straightforward orientation during index changes. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
RCMT 10T3M0 T9225 Wendeplatten - Tungaloy
Take advantage of a robust CVD-coated carbide grade and a proven RS chipbreaker to maintain productive turning in variable engagement conditions; the ISO-conforming design ensures straightforward holder compatibility and secure clamping. Order the insert through Metav Werkzeuge or consult their technical team for specification and availability. RCMT 10T3M0 T9225 Tungaloy turning insert (RCMT10T3M0-RS) A RCMT10T3M0-RS indexable turning insert for external and internal turning, engineered for medium to heavy steel machining with a CVD-coated carbide grade CVD-coated carbide grade T9225 Robust universal grade for steel Round 10 mm, 3.97 mm thickness 7° clearance; cylindrical hole and countersink Consistent performance where cuts vary The combination of a CVD-coated carbide substrate and the T9225 grade delivers a balance of toughness and wear resistance that suits changing cut conditions. Designed for medium to heavy steel turning, the insert supports interrupted cuts and variable engagement without frequent index changes, which helps to sustain cycle times and tool life. The RS chipbreaker promotes stable chip formation and evacuation, reducing the risk of chip-related downtime while improving surface integrity on workpieces. Secure mounting and ISO interchangeability for rapid setups Compliance with the ISO indexable insert system means the geometry and mounting features follow standardised dimensions, so compatibility with the correct holder depends on form, relief angle, tolerance class, clamping arrangement, size and thickness. The round 10 mm form and 3.97 mm thickness are complemented by a cylindrical hole with single-side countersink (40°–60°) to ensure reliable clamping and repeatable seating. Operators benefit from predictable positioning and simple replacement, reducing setup time and supporting consistent machining accuracy. Practical system approach for shop-floor reliability The insert is intended to be used as part of a system: the ISO insert, a suitable external holder or boring bar, a support/ clamping set and the correct fastening screws. Selecting the appropriate chipbreaker and the T9225 grade for the workpiece and machining stability will lower the chance of unplanned stops and contribute to reproducible part quality. For workshops seeking robust turning performance under mixed or interrupted conditions, this insert provides a pragmatic route to greater process security and reduced tool-change frequency. For robust, reliable steel turning choose the Tungaloy T9225 RCMT insert and contact Metav Werkzeuge for tailored advice and fast supply. Technical Data Article number: 6781085 Manufacturer SKU: TUN6781085 SKU: 6781085-Tungaloy Model series: ISO indexable turning inserts Material: carbide Grade: T9225 Chipbreaker: RS ISO designation: 10T3M0 Application: turning Core data Thickness: 3.97 mm Size: 10 mm Relief angle: 7° Corner radius: 0 Manufacturer item number: 6781085 Special features CVD-coated carbide Round plate form With cylindrical hole and single-side countersink (40°–60°) Designed for medium to heavy steel machining Suitable for interrupted cuts System components: insert, holder/boring bar, support/clamp, spare screws FAQ How is compatibility with a toolholder determined? Compatibility depends on the insert form, relief angle, tolerance class, clamping method, size and thickness; the RCMT10T3M0-RS follows ISO conventions so the correct holder must match those parameters. Which materials is this insert suited to machine? The T9225 grade is a robust universal grade intended for medium to heavy steel machining, performing well under variable engagement and slightly interrupted cuts. What benefit does the RS chipbreaker provide? The RS chipbreaker on the RCMT10T3M0-RS controls chip formation for better evacuation during heavier cuts, which helps maintain surface quality and reduces the risk of chip interference. How is the insert fixed in the holder? Fixing is via the cylindrical hole with a single-side countersink (40°–60°); correct fastening hardware and clamping set are required to ensure secure, repeatable seating. What system components are required for correct operation? A matching ISO indexable holder or boring bar, the correct support/clamp set and the appropriate fastening screws complete the system for reliable use of this insert. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
RCMT 1204EN AH120 Wendeplatten - Tungaloy
Take advantage of the combination of PVD-coated carbide grade AH120 for enhanced wear resistance and a single-sided chipbreaker for stable chip control to secure consistent milling results; order directly through Metav Werkzeuge or consult the technical team for application-specific advice. RCMT 1204EN AH120 indexable insert – round milling insert with hole for face and shoulder milling by Tungaloy RCMT 1204EN AH120 is a round indexable insert designed for milling applications where a sharp cutting edge and process security are required; compatible insert seat, geometry and cutter body must match. Round 12 mm insert, 4.76 mm thick PVD-coated carbide grade AH120 Single-sided chipbreaker, with hole Suited to face, shoulder and slot milling Reliable cutting performance that keeps production moving The combination of a PVD-coated carbide substrate and the AH120 grade provides a balance between wear resistance and fracture toughness, making the insert suitable for a broad range of milling tasks. In practice, the coating reduces adhesion and abrasion on the cutting edge, while the carbide core maintains edge stability under load. This results in a more consistent tool life and fewer unexpected interruptions to the machining process, which supports higher uptime and predictable planning in serial production and job-shop environments. Precise fit and secure clamping for repeatable results A correct seat and matching cutter body geometry are essential; the insert’s round 12 mm format and with hole configuration deliver secure axial locating and repeatable seating. The 4.76 mm thickness and the specified countersink ensure stable clamping and reduced micro-movement during operation. When mounted in a properly matched milling cutter, the design minimises vibration and run-out sensitivity, improving dimensional accuracy and surface finish without requiring additional operator intervention. Controlled chip formation for safer, faster machining The integrated single-sided chipbreaker is engineered to direct chips reliably during face, shoulder, slot, high-feed and contour milling. By shaping the chip flow, the insert reduces the risk of chip re-cutting and tool overload, enabling higher material removal rates with predictable forces. The hole with a cylindrical bore and a one-sided countersink (40°–60°) contributes to controlled clamping geometry and supports the chipformer’s function, particularly when processing medium to demanding workpiece materials in industrial applications. Application scope and who benefits most This insert is intended for milling applications where process security and a sharp cutting edge are priorities—typical uses include face and shoulder milling, grooving and contour work as determined by the cutter family. Production engineers, CNC programmers and tooling buyers in contract machining and discrete manufacturing will value the balance of durability and reliable chip control. Selection should always consider the matching cutter body and seat; if the assembly components align, the insert delivers stable, repeatable performance across a wide variety of tasks. For tailored recommendations based on workpiece material or cutting conditions, contact Metav Werkzeuge for expert guidance and to order the appropriate Tungaloy inserts and compatible cutter bodies Technical data Article number: 5812601 Manufacturer SKU: TUN5812601 Stock SKU: 5812601-Tungaloy Model series: Fräswendeschneidplatten Material: cemented carbide Facts Diameter: 12 mm Thickness: 4.76 mm Clearance angle: 7° Countersink angle: 40°–60° ISO designation: RCMT1204EN Special features Grade: AH120 Coating: PVD Shape: round With hole: cylindrical bore with one-sided countersink Chipbreaker: single-sided Typical applications: face, shoulder, slot, high-feed and contour milling System requirement: matching insert seat, geometry and cutter body FAQ What milling tasks is this insert designed for? The RCMT1204EN AH120 insert is intended for face, shoulder, slot, high-feed and contour milling where a sharp cutting edge and process security are required. How should the insert be mounted to ensure reliable performance? Mount the insert in a cutter body with a compatible seat and matching geometry; correct clamping using the hole and countersink ensures repeatable seating and reduced micro-movement. What advantages does the AH120 grade provide compared with standard grades? AH120 offers a PVD-coated carbide combination with enhanced wear resistance and resistance to chipping, delivering longer edge life and steady performance in demanding milling operations. Does the hole and one-sided countersink affect chip control? Yes, the cylindrical hole with a one-sided countersink supports stable clamping and complements the single-sided chipbreaker to promote consistent chip evacuation during machining. Can this insert be used for high-feed milling? The insert’s design and chipbreaker make it suitable for high-feed strategies within the limits of the cutter family assignment; the final suitability depends on the cutter body and process parameters. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
RCMT 1204EN AH120 Wendeplatten - Tungaloy
Benefit from the combination of a PVD-coated carbide grade and a dedicated chipbreaker for stable milling performance and extended tool life; the insert delivers reliable process security and consistent surface quality. Order the RCMT1204EN AH120 insert directly via Metav Werkzeuge or ask our consultants if needed. RCMT 1204EN AH120 indexable insert for milling — Tungaloy The RCMT1204EN AH120 indexable insert is a PVD-coated carbide cutting element engineered for Tungaloy milling systems, suitable for face, shoulder, slot, high-feed and contour milling. PVD-coated carbide grade AH120 One-sided chipbreaker geometry Round 12 mm insert, 4.76 mm thickness Cylindrical hole with 40°–60° countersink Stable cutting edge for consistent production results The PVD-coated carbide grade AH120 combines wear resistance with a design optimised to resist edge chipping, delivering process security in interrupted and continuous cuts. The coating improves thermal resistance and wear behaviour, which results in fewer edge changes and more predictable tool life. For production environments where surface finish and repeatability matter, this chemistry and microstructure reduce downtime and support tighter tolerances without complex adjustments. Geometry tailored to versatile milling tasks A round insert with a diameter of 12 mm and a plate thickness of 4.76 mm offers flexibility across a range of milling operations. The one-sided chipbreaker promotes controlled chip formation and evacuation, reducing the risk of built-up edge and improving surface quality. The insert features a 7° relief angle and a central cylindrical hole with a one-sided countersink (40°–60°) for secure clamping; correct seating and geometry matching with the cutter body are essential for optimal performance. These geometric details suit face, shoulder and contour milling when matched to the appropriate milling body family. Practical integration and reliable system behaviour The insert is intended for use in a complete system comprising milling body, indexable insert, clamping screw and, where required, a shim or backing plate. The RCMT format ensures simple indexing and replacement, while the central hole and countersink provide a stable mechanical interface that maintains repeatable positioning after insert changes. Compatibility with Tungaloy milling bodies should be verified by matching the seating form and geometry; the manufacturer article number 5812595 and SKU TUN5812595 identify the exact item for procurement and inventory control. Where process security and reduced variability are priorities, this insert supports efficient manufacturing workflows. Contact Metav Werkzeuge for application advice and to arrange supply of the RCMT1204EN AH120 insert; consultants are available by email at info@metav-werkzeuge.com or by phone at +49 2822 7131930 Technical data Article number: 5812595 SKU: 5812595-Tungaloy Manufacturer SKU: TUN5812595 Model series: Fräswendeschneidplatten Application: Milling Facts Insert designation: RCMT1204EN Grade: AH120 Material: Carbide Plate diameter: 12 mm Plate thickness: 4.76 mm Relief angle: 7° Hole: with hole Hole style: cylindrical hole + one-sided countersink (40°–60°) Special features PVD-coated carbide One-sided chipbreaker Round plate shape Suitable for face, shoulder, slot, high-feed and contour milling (depending on tool family) System components: milling body, insert, clamping screw, optional shim FAQ What materials is this insert suited for? The RCMT1204EN AH120 insert is a PVD-coated carbide grade designed primarily for general milling tasks; material suitability depends on the chosen cutting data and the associated milling body. How does the chipbreaker influence performance? The one-sided chipbreaker on the insert promotes controlled chip formation and evacuation, improving surface finish and reducing the likelihood of built-up edge during milling operations. What must be checked before fitting the insert? Compatibility of the insert seating, geometry and the milling body is required; ensure the seat and clamping arrangement match the RCMT1204EN designation and the clamping screw is correctly torqued. Is the RCMT1204EN AH120 available with other coatings or grades? This listing specifies the AH120 PVD-coated grade; alternative grades or coatings may be available from the manufacturer for different process requirements. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
RCMT 1204EN AH140 Wendeplatten - Tungaloy
Take advantage of the combination of sharp cutting performance, reliable chip control and easy integration into Tungaloy milling systems for stable production results. Order the insert directly via Metav Werkzeuge or contact our consultants for application advice. RCMT1204EN AH140 Tungaloy milling insert — PVD-coated carbide, with hole, 7° relief The RCMT1204EN AH140 is a round indexable milling insert for Tungaloy milling systems, engineered for face, shoulder, slot, high-feed and contour milling where a sharp cutting edge and process security are required PVD-coated carbide grade AH140 One-sided chipbreaker for stable chip control Round 12 mm insert with 4.76 mm thickness Cylindrical hole with 40°–60° countersink Consistent cutting performance for mixed milling tasks The PVD-coated carbide grade AH140 delivers a balance of sharpness and wear resistance that suits a wide range of milling operations. Insert geometry and grade were selected to maintain a sharp cutting edge while resisting premature wear, which reduces the need for frequent index changes. For production environments that alternate between face, shoulder and contour passes, this combination provides reproducible results and helps maintain cycle-time targets. Reliable chip control reduces interruptions Equipped with a one-sided chipbreaker and a cylindrical hole with countersink, the insert promotes predictable chip formation and evacuation. Stable chip control reduces the risk of built-up edge and workpiece damage, lowering machine downtime and tool handling. The integrated seating and hole style ensure secure clamping in compatible tool bodies and contribute to repeatable machining under varying cutting conditions. Simple compatibility with Tungaloy milling systems Designed for use in matching Tungaloy tool holders, the round shape and standard ISO designation 1204EN make mechanical integration straightforward when seat and geometry correspond. The insert’s relief angle of 7° supports efficient engagement and clearance in common pocket designs, while the standard size simplifies tool inventory management. Clear specification of seat geometry and tool family alignment avoids misfits and streamlines tool changeovers. Durable performance that supports productivity The combination of the chosen carbide grade and PVD treatment enhances surface hardness and resistance to micro-chipping, resulting in long tool life and fewer index changes over a production shift. For shops aiming to improve overall equipment effectiveness, this wear resistance contributes directly to higher throughput and reduced tooling costs per part when used in appropriate cutting windows and with verified process parameters. For application-specific recommendations and availability of Tungaloy RCMT1204EN AH140 inserts, contact Metav Werkzeuge for expert guidance and rapid delivery via info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: 5812602 Manufacturer SKU: TUN5812602 SKU: 5812602-Tungaloy Model series: Fräswendeschneidplatten Facts Insert size: 12 mm Thickness: 4.76 mm Relief angle: 7° Countersink: 40°–60° Hole: cylindrical hole with single-side countersink Special features Material: carbide Coating: PVD (grade AH140) Shape: round Chipbreaker: one-sided Application: face, shoulder, slot, high-feed and contour milling depending on tool family Insert designation: RCMT1204EN FAQ What materials is this insert suited for? The RCMT1204EN AH140 insert is a PVD-coated carbide product designed for general milling; its wear properties make it suitable for a broad range of materials depending on cutting data and tool body selection. How does the chipbreaker affect performance? The one-sided chipbreaker on the RCMT1204EN AH140 promotes controlled chip formation and evacuation, improving process stability and reducing the likelihood of built-up edge during interrupted cuts. Is the RCMT1204EN compatible with all Tungaloy tool bodies? Compatibility requires that insert seat, geometry and clamping match the tool body; the RCMT1204EN follows the ISO 1204EN form and fits Tungaloy milling systems that accept this designation. What is the relief angle and why does it matter? The relief angle is 7°, providing clearance during engagement to reduce rubbing and support efficient material removal in typical pocket designs. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
RCMT 1204EN AH140 Wendeplatten - Tungaloy
A compact, PVD-coated cemented carbide insert in AH140 grade with a 7° relief angle and single-sided chipbreaker combines sharp-edge performance with process security; order the insert directly via Metav Werkzeuge or consult our specialists for application advice. RCMT RCMT1204EN AH140 Tungaloy indexable milling insert for milling RCMT1204EN AH140 Tungaloy insert designed for application in indexable milling systems for face, shoulder, slot, high-feed and contour milling depending on the assigned cutter family PVD-coated cemented carbide AH140 Sharp cutting edge with 7° relief angle Round 12 mm insert, 4.76 mm thick Cylindrical hole with single-side countersink (40°–60°) Reliable chip control for productive milling The round indexable insert provides consistent chip formation thanks to its single-sided chipbreaker, which reduces the risk of irregular chips and machine stoppages. In practical terms, this means fewer interruptions during batch production and more predictable cycle times. The combination of a defined chipbreaker geometry and the circular form also facilitates smooth transitions in contours and shoulder passes, supporting stable cutting forces and improved surface quality. Durable cutting edge and coating for process security Made from cemented carbide and finished with a PVD coating, the grade AH140 is developed for a balance of wear resistance and fracture toughness. This composition is particularly suited when a sharp cutting edge and high process reliability are required simultaneously. The surface treatment helps to reduce adhesion and thermal wear, extending edge life under moderate to demanding milling conditions and lowering the frequency of index changes. Compact geometry that eases tool integration With a nominal size of 12 mm and a plate thickness of 4.76 mm, the insert fits into many standard milling bodies where matching of seat, geometry and cutter body is essential. The cylindrical hole with a single-side countersink (40°–60°) ensures accurate seating and secure clamping, which in turn maintains repeatability across re-indexing. The 7° relief angle reduces rubbing on the flank, improving entry behaviour and reducing built-up edge on softer materials. Application flexibility and machining benefits This insert is intended for a broad range of milling tasks — from planing and shoulder operations to high-feed and contour work, depending on the chosen tool family. The AH140 grade is optimised for resistant wear behaviour and chipping protection, offering a practical solution when machining demands both a fine initial edge and robust performance. Selecting this insert can contribute to fewer rejects, less rework and a more predictable production flow. For reliable milling performance with Tungaloy-grade security, contact Metav Werkzeuge to specify the correct cutter body or to receive tailored application recommendations. Technical data Article number: 5812596 Core specifications Designation: RCMT1204EN AH140 Manufacturer SKU: TUN5812596 Size: 12 mm Thickness: 4.76 mm Relief angle: 7° Countersink angle: 40°–60° Special features Material: cemented carbide Coating: PVD Grade: AH140 Shape: round insert Chipbreaker: single-sided Hole: with cylindrical hole and one-sided countersink Typical use: milling (face, shoulder, slot, high-feed, contour) Model series: Indexable milling inserts (Fräswendeschneidplatten) FAQ What materials is this insert suited to machine? The RCMT1204EN AH140 Tungaloy insert is designed for general milling tasks and provides a balance of wear resistance and toughness; it is suitable for a wide range of engineering materials where a sharp edge and process stability are required. How is the insert clamped in the milling body? The insert features a cylindrical hole with a single-side countersink (40°–60°) to ensure secure seating and reliable clamping when used with compatible Tungaloy milling bodies. Can the AH140 grade withstand interrupted cuts? The AH140 grade combines wear resistance with chipping protection, offering improved performance under conditions that can cause edge breakdown; it therefore performs well in many interrupted-cut scenarios within its intended application range. Is the coating important for tool life? Yes, the PVD coating on the cemented carbide insert reduces adhesion and thermal wear, contributing to longer edge life and more consistent machining results over a production run. Which cutter bodies are compatible with the insert? Compatibility requires matching the insert seat, geometry and cutter body; the RCMT1204EN designation indicates the nominal form and must be used with milling bodies that accept RCMT-style round inserts. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
RCMT 1204EN AH725 Wendeplatten - Tungaloy
Take advantage of the combination of PVD-coated carbide, robust AH725 grade and precise plate geometry for secure, productive milling operations. The insert's universal, fracture‑resistant composition and standard hole design ensure consistent chip control and easy integration into Tungaloy milling systems. Order the RCMT1204EN AH725 Tungaloy insert directly via Metav Werkzeuge or ask our consultants if needed. RCMT 1204EN AH725 – RCMT indexable insert for milling, PVD-coated carbide by Tungaloy The RCMT1204EN AH725 is a round indexable insert engineered for multi-purpose milling applications in Tungaloy systems, offering reliable chip control and high process security. PVD-coated carbide for extended tool life Universal, fracture-resistant AH725 grade Round 12 mm plate, 4.76 mm thickness Cylindrical hole with 40°–60° countersink Increased process security through proven PVD coating and grade The combination of a PVD-coated carbide substrate with the AH725 grade provides a balanced wear resistance and toughness profile, designed to reduce edge chipping under interrupted cuts. This results in stable machining and fewer unplanned tool changes, improving cycle time reliability for components machined from steel and stainless steel. The coating contributes to thermal stability at elevated cutting speeds, which supports higher productivity without compromising surface quality. Simple integration into modular milling systems Designed for use in Tungaloy milling bodies, the insert relies on a consistent seating geometry: a round plate with 12 mm diameter and 4.76 mm thickness combined with a central hole arrangement. The cylindrical hole with a single‑side countersink (40°–60°) ensures repeatable clamping via the clamping screw and, where required, a locating shim. This compatibility minimises set‑up time and secures the cutting edge in the tool body for reproducible results across production batches. Effective chip control for diverse milling tasks A one-sided chipbreaker profile enables controlled chip formation across a range of operations from face and shoulder milling to slotting and contouring, depending on the chosen tool family. The fracture‑resistant grade is particularly advantageous when machining mixed batches or smaller cutters, where process robustness is critical. Consistent chip evacuation reduces rework risk and supports stable surface finish, translating into lower downstream processing. Practical selection and application guidance for production use As part of a system comprising the milling body, indexable insert, clamping screw and, if needed, a shim, this insert is a pragmatic choice when tool standardisation and stock rationalisation are priorities. The combination of geometry, grade and coating targets long tool life and predictable wear patterns, which supports maintenance planning and cost calculations for series production. For specific cutting data, matching the insert to the designated tool family and machine capability is advised to achieve optimal results. Contact Metav Werkzeuge to discuss the RCMT1204EN AH725 from Tungaloy and secure inserts for immediate production use – email info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: 5812594-Tungaloy Manufacturer item number: 5812594 Manufacturer SKU: TUN5812594 Model series: Fräswendeschneidplatten Application: Milling Material: carbide Core dimensions Plate size: 12 mm Plate thickness: 4.76 mm Clearance angle: 7° Hole style: cylindrical hole + one-sided countersink (40°–60°) Special features Grade/coating: AH725, PVD-coated carbide Plate shape: round Chipbreaker: one-sided Designed for use in Tungaloy milling systems Universal, fracture-resistant grade suitable for steel and stainless steel FAQ What materials is this insert suitable for? The RCMT1204EN AH725 insert is specified for machining steel and stainless steel due to its universal, fracture‑resistant AH725 grade and PVD coating. Can this round insert be used in any milling body? The insert is intended for use in Tungaloy milling systems; the seat, geometry and tool body must be technically compatible with the RCMT1204EN form. How does the chipbreaker affect machining? The one‑sided chipbreaker promotes controlled chip formation, improving evacuations and surface quality during face, shoulder and contour milling operations. What is the benefit of the central hole with countersink? The cylindrical hole with a single‑side countersink (40°–60°) ensures repeatable clamping and secure seating in the milling body, supporting consistent tool performance. Which product codes identify this item? This article is listed under manufacturer item number 5812594 and manufacturer SKU TUN5812594; it is marketed as RCMT1204EN AH725 by Tungaloy. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
RCMT 1204EN AH725 Wendeplatten - Tungaloy
Take advantage of the PVD‑coated carbide AH725 for consistent performance across steel and stainless steels and the one‑sided chipbreaker for controlled chip formation; ensure the insert seat, geometry and cutter body match to secure process reliability. Order matching inserts or request application advice via Metav Werkzeuge. RCMT 1204EN AH725 milling insert – Tungaloy A RCMT 1204EN AH725 indexable insert for Tungaloy milling systems, designed for face, shoulder, slot, high‑feed and contour milling in mixed‑material production. PVD‑coated carbide AH725 for reliability Universal grade for steel and stainless steels One‑sided chipbreaker for controlled chips Round 12 mm insert with central hole High reliability for mixed‑material milling The AH725 grade is a PVD‑coated carbide developed for universal use, offering stable edge behaviour across steel and stainless steels. In practice this reduces the need for frequent tool changes where jobs include varying materials, which improves uptime and lowers machining interruptions. The coating stabilises the cutting edge and supports process reliability in higher workload cycles. Predictable chip control and clearance for small tools A single‑side chipbreaker and the central hole with a cylindrical aperture plus a single‑side countersink (40°–60°) deliver consistent chip formation and safe evacuation even on compact cutters. The 12 mm round form factor combines reliable seating with balanced cutting dynamics, helping to avoid recutting and to maintain surface quality during interrupted cuts. Easy integration into matched milling systems As an indexable insert, compatibility depends on precise seat geometry and cutter body design; the insert requires a matching cutter to perform optimally. The 7° clearance and 4.76 mm thickness are engineered to provide stable clamping and predictable wear progression. Correct mating of the insert and cutter body supports longer tool life and repeatable results on serial production. Practical choice for common milling operations For jobs requiring consistent output—such as face and shoulder milling, slots or contours—this insert offers a balance of robustness and control. The grade is particularly useful for smaller‑diameter cutters and applications where high process safety is essential. Where surface finish and edge stability matter, the combination of geometry and Tungaloy‑grade coating contributes to reproducible component quality. Contact Metav Werkzeuge for tailored application advice and to arrange supply of matching Tungaloy inserts; email info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: 5812600 Manufacturer SKU: TUN5812600 SKU: 5812600‑Tungaloy Model series: Fräswendeschneidplatten Designation: RCMT1204EN AH725 Tungaloy indexable insert Core data Insert size: 12 mm Thickness: 4.76 mm Relief angle: 7° Hole style: cylindrical hole + single‑side countersink (40°–60°) Shape: round Special features PVD‑coated carbide Grade: AH725 One‑sided chipbreaker Suitable for steel and stainless steels Typical applications: face, shoulder, slot, high‑feed and contour milling For use in Tungaloy milling systems; insert seat, geometry and cutter body must match FAQ What materials is this insert suitable for? The RCMT 1204EN AH725 insert is specified for machining steel and stainless steels, the universal AH725 grade providing reliable performance across those material groups. Which operations is the insert designed for? This indexable insert is suited to face, shoulder, slot, high‑feed and contour milling when used in the corresponding Tungaloy milling cutter family. How does the central hole affect mounting and performance? The central hole with a cylindrical bore and single‑side countersink (40°–60°) ensures secure clamping and correct seating in compatible cutter bodies, which helps to maintain repeatable cutting geometry. What are the key dimensions to check for compatibility? Confirm the insert size (12 mm), thickness (4.76 mm) and relief angle (7°) match the cutter seat; compatibility with the cutter body and seat geometry is essential for safe, repeatable operation. Is this a coated insert and what is the benefit? Yes, the insert uses a PVD‑coated carbide grade (AH725) that supports edge stability and wear resistance, improving tool life and process consistency in mixed‑material production. Manufacturer/Responsible: Tungaloy‑NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand‑new product from the manufacturer.
RCMT 1204FN KS15F Wendeplatten - Tungaloy
Combining robust carbide construction, the KS15F grade and the NAJ chipbreaker delivers dependable wear resistance and cutting-edge stability for efficient milling; order directly via Metav Werkzeuge or consult our specialists for compatibility guidance. RCMT 1204FN KS15F Tungaloy indexable milling insert – round 12 mm, carbide The RCMT1204FN-NAJ KS15F Tungaloy indexable insert is designed for versatile milling tasks, offering reliable chip control and edge stability for face, shoulder, slot, high-feed and contour milling. Compatible with Tungaloy milling systems Round 12 mm insert for flexible contact Carbide grade KS15F for balanced performance 7° relief angle and cylindrical bore with countersink Productive, predictable milling performance for series production The insert is manufactured from carbide, optimised for milling operations where repeatable results and tool life are decisive. The KS15F grade combines wear resistance and toughness to maintain the cutting edge under varied loads, which reduces tool-change frequency and increases uptime. Using a round geometry with a NAJ chipbreaker supports controlled chip formation in interrupted and continuous cuts, lowering the risk of workpiece marks and improving surface finish. This results in tangible productivity gains for batch and continuous machining. Secure clamping and precise seating for consistent cutting geometry A reliable clamping interface is essential for dimensional accuracy. The round insert features a cylindrical bore with a single-side countersink (40°–60°) that ensures correct seating and stable fixation on compatible milling bodies. The specified 4.76 mm thickness and 12 mm diameter create a low-profile contact that helps maintain concentricity and reduces vibration. Correct matching of insert seat, geometry and milling body leads to repeatable toolpaths and predictable tool life across a production run. Broad application range with simplified process selection This insert supports face, shoulder, slot, high-feed and contour milling depending on the chosen cutter family, making it suitable for workshops that require flexible tooling options. The 7° relief angle enables effective shear engagement while preserving cutting-edge stability, especially in tough or variable materials. Thanks to the round form, fewer inventory variants are needed to cover multiple milling approaches, simplifying tooling management and lowering logistical complexity. Practical advantages and handling notes for process engineers The NAJ chipbreaker is tuned to promote short, controllable chips under a variety of feeds and depths of cut, which eases chip evacuation and reduces downtime for clearing. The insert is intended for use in properly matched Tungaloy milling systems; seat geometry and clamping torque must conform to the tool manufacturer's guidelines to achieve rated performance and safety. Stored and handled correctly, the carbide body resists typical workshop impacts and preserves the coated or uncoated cutting edges for longer operation. Contact Metav Werkzeuge for matching milling bodies, verified clamping options and application-specific recommendations; email info@metav-werkzeuge.com or call +49 2822 7131930 to discuss suitability for particular materials and machining parameters Technical data Article number: 5812593 SKU: 5812593-Tungaloy Manufacturer SKU: TUN5812593 Series: Fräswendeschneidplatten Numbers Diameter/size: 12 mm Thickness: 4.76 mm Relief angle: 7° ISO designation: 1204FN Bore: with hole Countersink angle: 40°–60° Angle: 0° Special features Carbide material Grade KS15F Chipbreaker NAJ Round insert form Cylindrical bore with single-side countersink (40°–60°) Compatible with Tungaloy milling systems Intended for face, shoulder, slot, high-feed and contour milling Requires matching insert seat and geometry FAQ What operations is this insert suitable for? The RCMT1204FN-NAJ KS15F Tungaloy indexable insert is designed for face, shoulder, slot, high-feed and contour milling when used in a compatible Tungaloy milling body. Which material is the insert made from and what does KS15F mean? The insert is made from carbide and the KS15F designation denotes a Tungaloy grade engineered for a balance of wear resistance, toughness and cutting-edge stability suitable for general milling. How does the NAJ chipbreaker affect machining? The NAJ chipbreaker promotes controlled chip formation and evacuation, improving process reliability and surface finish for the intended milling applications. What dimensions and clamping features should be noted? Key dimensions are 12 mm diameter and 4.76 mm thickness; the insert has a cylindrical bore with a single-side countersink (40°–60°) that requires the correct mating seat and clamping screw for secure fixation. Can this insert be used with non-Tungaloy milling bodies? Performance depends on exact seat geometry and clamping method; the insert is intended for Tungaloy milling systems, and compatible bodies must match the specified insert seat and geometry for safe and repeatable use. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
RCMT 1204M0 AH140 Wendeplatten - Tungaloy
Take advantage of the combination of PVD-coated AH140 carbide, a sharp cutting edge and the TurnTenFeed system for faster roughing and consistent process security. Order the insert directly via Metav Werkzeuge or consult our specialists for application advice. RCMT 1204M0 AH140 turning insert — Tungaloy, PVD-coated carbide for high-feed roughing RCMT1204M0 AH140 is a round indexable insert designed for high-feed turning and productive roughing under stable clamping conditions TurnTenFeed family for high-feed roughing PVD-coated AH140 carbide for wear resistance Round plate with cylindrical hole and countersink Increased material removal rates with controlled chip flow The TurnTenFeed series is engineered for high-feed turning, which raises material removal rates without sacrificing stability. The AH140 PVD-coated carbide provides a wear-resistant and chip-secure cutting edge, helping to maintain consistent cycle times in productive roughing operations. The result is a tangible improvement in throughput: sharper edge retention reduces edge failures and keeps tool change intervals predictable, supporting leaner production schedules. Stable clamping and repeatable seating for secure machining A round insert with a cylindrical hole plus single-sided countersink (40°–60°) ensures positive seating in compatible tool holders. The 7° relief angle and 4.76 mm plate thickness combine to deliver a balance between rigidity and cutting clearance, reducing chatter when conditions are stable. This geometric setup translates into reliable engagement at higher feeds and contributes to a repeatable machining process, lowering the risk of unexpected interruptions. Practical system benefits for workshop logistics The TurnTenFeed system comprises holders, indexable inserts and spare parts, allowing for coherent tool management across similar turning tasks. Using a standardised insert format such as this round RCMT-type simplifies inventory and reduces setup complexity. The single-sided chipbreaker supports effective chip control in roughing, which eases swarf handling and can improve surface integrity on the subsequent finishing pass. Application-focused alloy and edge performance The AH140 grade is developed to combine wear resistance with resistance to edge chipping, making it suitable where a sharp edge and process security are required. The 12 mm plate diameter and zero corner radius offer a consistent cutting profile for high-feed operations, while the PVD coating enhances lifetime under abrasive conditions. For manufacturers aiming to increase throughput with dependable tool life, this insert offers a pragmatic compromise between aggressiveness and robustness. For tailored recommendations on integrating Tungaloy AH140 inserts into production, contact Metav Werkzeuge for specialist advice and delivery options. Technical data Article number: 6850746 SKU: 6850746-Tungaloy Manufacturer SKU: TUN6850746 Model series: TurnTenFeed Specifications Plate size: 12 mm Plate thickness: 4.76 mm Relief angle: 7° Corner radius: 0 mm Special features Grade/coating: AH140, PVD-coated carbide Shape: round insert Hole: with cylindrical hole + single-sided countersink (40°–60°) Chipbreaker: one-sided Typical application: high-feed turning, productive roughing FAQ What operations is this insert designed for? The RCMT1204M0 AH140 Tungaloy insert is engineered primarily for high-feed turning and productive roughing under stable clamping conditions. Which tool system does the insert belong to? This insert is part of the TurnTenFeed series, delivered as an indexable component for matching holders and spare parts to form a complete turning system. What benefits does the AH140 grade deliver? The AH140 grade on the RCMT1204M0 provides improved wear resistance and resistance to edge chipping, ensuring a sharp cutting edge and process security during roughing. How does the insert help with chip control? The single-sided chipbreaker and round geometry support controlled chip formation in roughing applications, easing swarf evacuation and helping to protect the workpiece surface for subsequent finishing. Is the insert suitable for stocked tool management? Using standard RCMT inserts within the TurnTenFeed family simplifies inventory and enables rapid replacement and repeatable set-up across similar turning tasks. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
RCMT 1204M0 AH8005 Wendeplatten - Tungaloy
Benefit from the combination of PVD-coated AH8005 wear resistance and the TurnTenFeed geometry for high-feed roughing that delivers reliable material removal and extended tool life. Order the RCMT 1204M0 AH8005 indexable insert directly via Metav Werkzeuge or consult the specialists for application-specific recommendations. RCMT 1204M0 AH8005 indexable insert for turning — Tungaloy The RCMT 1204M0 AH8005 is an indexable insert engineered for productive high-feed turning and robust roughing under stable clamping conditions. PVD-coated AH8005 for heat-resistant alloys Engineered for high-feed roughing in turning One-sided chipbreaker for reliable chip control Cylindrical hole with single-sided countersink Boosted metal removal with consistent tool life The TurnTenFeed series is designed to maximise metal removal rates while keeping process forces predictable. With a PVD-coated carbide grade, the insert offers improved resistance to abrasive and adhesive wear when machining heat-resistant alloys and other demanding materials. The combination of a stable geometry and a wear-resistant coating reduces the frequency of index changes, which translates into higher productivity per shift and lower overall machining costs. The result is a measurable efficiency gain in heavy-duty roughing operations. Predictable chip formation for uninterrupted machining A one-sided chipbreaker provides controlled chip geometry and evacuation, minimising the risk of entanglement and machine stoppages. Clear, consistent chips ease disposal and protect workpiece surfaces during high-feed operations. In practice, this leads to fewer interruptions for cleaning and less toolholder maintenance, supporting a smoother production flow and improved process reliability. Design that simplifies clamping and repeatability The round insert form with a cylindrical hole and single-sided countersink (40°–60°) ensures secure seating in compatible toolholders and accurate repeatability after indexing. The insert thickness of 4.76 mm and the nominal size of 12 mm are optimised for rigid setups, while the 7° clearance angle supports effective cutting without excessive rubbing. These mechanical details translate into stable engagement at high feed rates, reducing vibration and promoting consistent surface quality on the workpiece. Broad material compatibility for versatile turning tasks Selected for turning applications, this insert is particularly suited to machining hard materials and heat-resistant alloys where thermal and abrasive loads are high. The AH8005 grade is engineered for stable performance in such environments, enabling productive roughing passes where robust edge retention and thermal stability are essential. When used under the recommended stable clamping conditions, the insert helps maintain cycle-time targets and reduces the need for intermediate finishing. For productive high-feed turning with Tungaloy’s AH8005 grade, contact Metav Werkzeuge for availability and tailored application advice at info@metav-werkzeuge.com or +49 2822 7131930 Technical data Article number: 6747784 Manufacturer SKU: TUN6747784 Brand: Tungaloy Series: TurnTenFeed Material: Carbide Coating: PVD Dimensions & figures Insert size: 12 mm Thickness: 4.76 mm Clearance angle: 7° Corner radius: 0 mm Hole: Cylindrical hole with single-sided countersink (40°–60°) Design & special features Round insert form One-sided chipbreaker Grade: AH8005 for heat-resistant alloys and hard materials Intended use: Turning, high-feed roughing System: Insert for holder with compatible clamping FAQ What materials is this insert suitable for? The RCMT 1204M0 AH8005 insert is designed for heat-resistant alloys and other hard materials, providing wear resistance and edge stability during productive roughing. How does the chipbreaker affect machining performance? The one-sided chipbreaker on this insert controls chip shape and evacuation, reducing interruptions and improving process stability during high-feed turning. Which toolholder type is required for correct clamping? A compatible turning holder that accepts round RCMT-style inserts with a cylindrical screw hole and countersink is required to achieve the intended repeatability and rigidity. What advantages does the PVD coating provide? The PVD-coated carbide grade enhances resistance to high-temperature wear and abrasive contact, extending index life in demanding turning operations. Is this insert part of a larger system for production turning? Yes, the insert belongs to the TurnTenFeed model series, which comprises holders, indexable inserts and spare parts tailored for high-feed, productive roughing operations. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
RCMT 1204M0 AH8015 Wendeplatten - Tungaloy
Take advantage of the combination of productive high‑feed performance, PVD‑coated AH8015 carbide and secure mounting for consistent roughing cycles; order the RCMT1204M0 insert via Metav Werkzeuge or consult our specialists for application support. RCMT 1204M0 AH8015 turning insert for turning — Tungaloy RCMT1204M0 AH8015 Tungaloy indexable insert designed for high‑feed turning and productive roughing under stable clamping conditions PVD-coated carbide grade AH8015 Designed for high-feed turning and roughing Round 12 mm insert with 4.76 mm thickness Cylindrical hole with single-side countersink 40°–60° Faster, more productive roughing cycles with proven grade balance The RCMT1204M0 insert from the TurnTenFeed family combines a PVD coating with AH8015 carbide to deliver a reliable balance between wear resistance and edge stability. This composition is optimised for productive roughing, allowing manufacturers to raise feed rates while maintaining predictable tool life. The insert’s chemistry and coating reduce the frequency of tool changes and stabilise machining cycles, which supports higher throughput on parts where consistent metal removal rates are required. Secure clamping and dependable chip control for uninterrupted shifts A round 12 mm insert with a cylindrical hole and a single-side countersink (40°–60°) provides positive seating and repeatable location in compatible tool holders. The one-sided chipbreaker channels swarf reliably during high‑feed operations, reducing chip entanglement and improving surface finish consistency. The geometry, together with a 7° clearance angle and a 4.76 mm plate thickness, simplifies fixture selection and contributes to stable cutting forces during heavy roughing passes. Suited for heat-resistant alloys and general heavy-duty applications The AH8015 grade is presented as a first choice for the general machining of heat-resistant alloys, offering a compromise between toughness and hardness that supports turning under elevated temperatures. This makes the insert appropriate for components where thermal load and work‑hardening are concerns. In environments with stable clamping and robust machine setups, this indexable insert promotes longer uninterrupted production runs and consistent dimensional results. System compatibility and practical stocking for production shops As part of a system comprising holders, indexable inserts and spare parts, the TurnTenFeed series simplifies inventory management and process planning. The round format and standardised hole style make the insert compatible with a range of clamping solutions intended for high‑feed turning. For production managers, the combination of a reliable grade and simple geometry helps to reduce set‑up variability and supports predictable tool replacement strategies. Contact Metav Werkzeuge for tailored advice on using Tungaloy TurnTenFeed inserts and to check current availability by email at info@metav-werkzeuge.com or by phone on +49 2822 7131930 Technical data Article number: 6747785 SKU: 6747785-Tungaloy Manufacturer SKU: TUN6747785 Dimensions & core data Insert designation: RCMT1204M0 Insert size: 12 mm Thickness: 4.76 mm Clearance angle: 7° Corner radius: 0 mm Design & features Shape: round Hole: cylindrical hole with single-side countersink (40°–60°) Chipbreaker: one-sided Coating: PVD Grade: AH8015 Material: carbide Model series: TurnTenFeed Typical application: turning (high-feed roughing) FAQ What materials is this insert intended for? The RCMT1204M0 AH8015 Tungaloy indexable insert is specified primarily for general machining of heat‑resistant alloys, where a balance of wear resistance and edge stability is required. How does the hole and countersink design affect clamping? The cylindrical hole with a single‑side countersink (40°–60°) ensures positive seating and repeatable location in compatible holders, improving clamping security for heavy roughing passes. Can this insert be used for finishing passes? This insert is engineered for productive roughing and high‑feed turning; while it may be used for certain semi‑finishing operations, a grade and geometry optimised for finishing would typically give better surface quality. What benefits does the AH8015 grade provide in production? AH8015 offers a compromise between toughness and hardness, reducing unexpected edge failure and supporting longer runs during the roughing of heat‑resistant materials, which contributes to steadier production yields. Is the insert compatible with standard TurnTenFeed holders and tooling systems? Yes, the RCMT1204M0 belongs to the TurnTenFeed series and is intended for use with the corresponding holders and system components to ensure repeatable performance and easy integration. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
RCMT 1204M0 AH905 Wendeplatten - Tungaloy
Take advantage of the combination of PVD-coated AH905 carbide and a geometry optimised for high-feed, productive roughing to keep cycle times low and tool changes infrequent. Order the insert directly via Metav Werkzeuge or consult the specialists for application guidance. RCMT 1204M0 AH905 Turning indexable insert — Tungaloy The RCMT 1204M0 AH905 is an indexable insert engineered for high-feed, productive rough turning under stable clamping conditions. PVD-coated AH905 carbide grade For high-feed, productive roughing One-sided chipbreaker, 7° relief Cylindrical hole with 40°–60° countersink Efficient cutting for high-feed roughing cycles The PVD-coated AH905 grade combines wear resistance with fracture toughness to sustain high-feed operations in demanding production environments. The coating improves flank wear behaviour, while the substrate provides a sharp cutting edge that stabilises the process and reduces the need for frequent edge changes. For shops aiming to increase material removal rates, this geometry and grade deliver measurable productivity gains through longer uninterrupted runs and consistent dimensional results. Secure clamping and predictable chip control A round insert form with a cylindrical hole and single-side countersink (40°–60°) ensures positive seating and repeatable clamping in compatible holders. The integrated one-sided chipbreaker and 7° relief angle promote controlled chip formation and evacuation during roughing passes, reducing the risk of built-up edge and unexpected tool damage. Clear chip control lowers machine downtime and supports stable surface integrity on the workpiece. System compatibility and pragmatic tool management Part of the TurnTenFeed series, the insert is intended for use within a system comprising holders, changeable inserts and spare parts, enabling straightforward replacement and inventory management. The standardised RCMT geometry supports widespread toolholder options, simplifying integration into existing turning stations and allowing quick swaps for uninterrupted production. The insert thickness and diameter are matched to common roughing applications for predictable mechanical support. Practical handling and application guidance With a plate thickness of 4.76 mm and a nominal size of 12 mm, the insert balances rigidity and accessibility for flank-heavy roughing operations. The grade is optimised for situations where process security and a reliable cutting edge are required, making it suitable for routine, high-volume turning tasks under stable fixturing. Technical staff will appreciate the familiar indexable format and minimal set-up adjustments when transitioning to this insert family. Contact Metav Werkzeuge for tailored application advice on Tungaloy PVD-coated AH905 turning inserts and to arrange supply; eMail: info@metav-werkzeuge.com — Phone: +49 2822 7131930 Technical Data Article number: 6879351 SKU: 6879351-Tungaloy Manufacturer SKU: TUN6879351 Model series: TurnTenFeed Facts Insert designation: 1204M0 Size: 12 mm Thickness: 4.76 mm Relief angle: 7° Corner radius: 0 Special features PVD-coated carbide, grade AH905 Round insert form Cylindrical hole with single-side countersink (40°–60°) One-sided chipbreaker System scope: holder, indexable inserts, spare parts Intended application: turning (high-feed, roughing) FAQ What is the intended application of this insert? The RCMT 1204M0 AH905 indexable insert from Tungaloy is intended for high-feed, productive rough turning within stable clamping setups. Which grade and coating are used on the insert? The insert uses a PVD-coated AH905 carbide grade, combining wear resistance and fracture toughness for reliable performance. How does the insert ensure secure clamping? Secure seating is achieved via the cylindrical hole with a single-side countersink (40°–60°), providing repeatable clamping in compatible toolholders. Is the insert part of a system that simplifies replacements? Yes, the insert belongs to the TurnTenFeed family and is supplied as part of a system comprising holders, indexable plates and spare parts for straightforward maintenance and replacement. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
RCMT 1204M0 NS9530 Wendeplatten - Tungaloy
Data inconsistency detected: the cutting material is specified as an "uncoated cermet", while the general material is given as "cemented carbide". These are different material designations and cannot both apply to the same cutting insert. Please clarify whether the item is a cermet grade or a cemented carbide grade and provide the corrected specification; a full product description cannot be generated until this discrepancy is resolved, as the conflicting information prevents accurate identification of the material properties, which are essential for determining the appropriate application, performance characteristics, and compatibility of the cutting insert with specific machining operations or conditions.
RCMT 1204M0 NS9530 Wendeplatten - Tungaloy
Combining a sharp, low-force cermet grade with a round RCMT form delivers exceptional surface finish and consistent, low-vibration performance in finishing turning; benefit from the TurnTenFeed system compatibility and order directly via Metav Werkzeuge or ask our consultants for application advice. RCMT 1204M0 NS9530 — Indexable insert for turning | Tungaloy RCMT 1204M0 NS9530 is a round indexable insert designed for finishing operations in turning, optimised for continuous cuts and small depths of cut within the TurnTenFeed system. Uncoated cermet grade NS9530 Sharp cutting edge for superior surface finish Optimised for continuous cuts and small depths Round RCMT insert with 7° clearance Delivering finer surfaces with lower cutting forces The combination of an uncoated cermet grade and a finely honed cutting geometry reduces cutting forces while promoting stable chip formation, which directly improves surface quality on steel workpieces. For production environments where repeatable finish and reduced secondary operations matter, the low-force behaviour of this insert shortens cycle times and lowers machine load. The NS9530 grade is formulated for finishing, so the result is fewer reworks and a more predictable process window. Precision finishing in continuous and small-step turning Designed for continuous cutting and modest depths of cut, this round RCMT insert provides consistent contact angles and predictable flank wear. The 7° clearance reduces rubbing and heat build-up, supporting longer effective tool life under stable clamping conditions. In practice, the geometry and single-sided chipbreaker mitigate unwanted vibrations, making the insert a reliable choice for fine-turning passes where dimensional accuracy and surface integrity are priorities. System benefits and workshop integration As a member of the TurnTenFeed model series, the insert integrates with a range of holders and spare parts to create a productive high-feed turning solution. The round RCMT form is forgiving in set-up and aids quick index changes, while the cylindrical hole with one-sided countersink ensures secure location and repeatability. The insert is suited to standard toolholding concepts and supports an efficient workflow when paired with appropriately rated holders. Contact Metav Werkzeuge for technical matching and to secure Tungaloy RCMT 1204M0 inserts — email info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: 6736606 SKU: 6736606-Tungaloy Manufacturer SKU: TUN6736606 Model series: TurnTenFeed Designation: RCMT1204M0 NS9530 Manufacturer: Tungaloy Core technical data Insert size: 12 mm Thickness: 4.76 mm Clearance angle: 7° Corner radius: 0 mm Hole style: cylindrical hole + one-sided countersink (40°–60°) Special features Material: Cemented carbide Grade: uncoated cermet NS9530 Chipbreaker: one-sided Insert form: round RCMT Application: Turning (finishing steel) System components: holders, inserts and spare parts (TurnTenFeed family) FAQ Which materials is this insert best suited to machine? The RCMT 1204M0 NS9530 insert is optimised for finishing on steel; the NS9530 cermet grade is formulated to deliver low cutting forces and high surface quality on continuous cuts. Can the insert be used for high-feed roughing? Although the TurnTenFeed series targets high-feed strategies, the NS9530 grade and the RCMT round form are specified for finishing and small depths of cut rather than primary roughing passes. What is the function of the cylindrical hole and countersink? The cylindrical hole with a one-sided countersink (40°–60°) secures the insert reliably in the seat, ensuring repeatable positioning and stable clamping during turning. How does the 7° clearance affect performance? A 7° clearance reduces flank contact and rubbing, which lowers heat generation and supports better surface finish and consistent tool life when used under stable fixturing. Is this insert compatible with existing TurnTenFeed holders? Yes, the RCMT1204M0 is part of the TurnTenFeed family and is intended to work with compatible holders and system components designed for that series. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
RCMT 1204M0 T9215 Wendeplatten - Tungaloy
Take advantage of the combination of CVD-coated carbide wear resistance and a secure mounting geometry to maintain high productivity during rough turning; order the insert directly via Metav Werkzeuge or request application advice from our consultants. RCMT 1204M0 T9215 indexable insert for turning — Tungaloy TurnTenFeed RCMT1204M0 T9215 is a round indexable insert engineered for high-feed turning and productive roughing under stable clamping conditions TurnTenFeed for high-feed turning CVD-coated carbide for wear resistance One-sided chipbreaker for reliable chip control Cylindrical hole with countersink for secure seating Engineered for productive roughing with durable CVD coating The TurnTenFeed family delivers a combination of geometry and material designed specifically for productive roughing. The CVD-coated carbide grade T9215 balances high wear resistance with fracture toughness, making it a reliable choice for the machining of medium steels. This balance reduces the frequency of indexable insert changes and supports continuous to slightly interrupted cuts, which in turn lowers machine idle time and increases throughput. The result is a predictable performance profile during extended roughing cycles. Stable seating and robust edge support for high-feed applications A round 12 mm insert body with 4.76 mm thickness and an accurately formed hole ensures stable seating in compatible tool holders. The insert’s 7° relief angle reduces radial cutting forces while preserving the cutting edge under the heavy loads typical of high-feed turning. The cylindrical hole with a single-sided countersink (40°–60°) provides secure axial registration and repeatable positioning, which helps to maintain dimensional consistency and surface quality across long production runs. Controlled chip formation and practical system compatibility The one-sided chipbreaker is tuned to promote effective chip control during roughing of medium steels, preventing chip entanglement and easing evacuation in common turning setups. As part of the TurnTenFeed system, the insert integrates with a range of holders, spare parts and standard indexable insert tooling, simplifying inventory and replacement. The compact round form factor supports flexible seat orientations and is straightforward to index, enabling quick edge changes and minimal downtime. For application advice, interchange compatibility checks or to specify Tungaloy TurnTenFeed inserts for a particular turning task, contact Metav Werkzeuge at info@metav-werkzeuge.com or call +49 2822 7131930 for prompt technical guidance Technical data Article number: 6773834 SKU: 6773834-Tungaloy Manufacturer SKU: TUN6773834 Manufacturer: Tungaloy Model series: TurnTenFeed Designation: RCMT1204M0 T9215 Core data Size: 12 mm Thickness: 4.76 mm Relief angle: 7° Corner radius: 0 mm Countersink angle: 40°–60° Special features CVD-coated carbide (T9215) Round insert form With hole: cylindrical hole + one-sided countersink One-sided chipbreaker Designed for high-feed turning and productive roughing System components: holder, indexable inserts and spare parts FAQ What materials is this insert best suited for? The RCMT1204M0 T9215 indexable insert is specified for medium steel machining and excels in high-feed turning where a balance of wear resistance and fracture toughness is required. How does the hole and countersink design benefit clamping? The cylindrical hole with a single-sided countersink (40°–60°) on the RCMT1204M0 ensures repeatable axial registration and secure seating, improving stability during heavy roughing cuts. Is this insert compatible with standard TurnTenFeed holders? Yes, the insert is part of the TurnTenFeed system and is compatible with the corresponding holders and spare parts intended for this series. What advantage does the one-sided chipbreaker provide? The one-sided chipbreaker promotes controlled chip formation during roughing, reducing the risk of chip build-up and facilitating reliable evacuation in conventional turning setups. Can this insert handle slightly interrupted cuts? The T9215 grade offers good fracture resistance, making the insert suitable for continuous to slightly interrupted cuts commonly encountered in productive roughing. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
RCMT 1204M0 T9215 Wendeplatten - Tungaloy
Combine high-feed turning, a CVD‑coated carbide grade (T9215) and a round 12 mm plate for reliable, productive roughing; order the insert directly via Metav Werkzeuge or consult the specialists for process recommendations. RCMT 1204M0 T9215 indexable insert for turning — Tungaloy The RCMT1204M0 T9215 is an indexable insert engineered for high‑feed, productive rough turning under stable clamping conditions. CVD‑coated carbide grade T9215 Optimised for high‑feed roughing Round insert 12 mm, 4.76 mm thick Single‑sided chipbreaker with countersunk hole Maximise material removal with controlled chip flow The TurnTenFeed family is designed to boost throughput in roughing operations by enabling higher feeds while maintaining stability. The CVD‑coated carbide grade T9215 combines wear resistance with fracture toughness, which translates into more consistent cutting cycles during continuous to slightly interrupted cuts. The round 12 mm plate and the single‑sided chipbreaker ensure predictable chip formation and evacuation, reducing the need for frequent intervention. For technicians evaluating cutting parameters, the combination of plate geometry and coating supports increased metal removal rates without compromising surface integrity. Reliable tool life and fewer unexpected interruptions A focus on substrate and coating chemistry yields a tool that resists abrasive wear and resists edge chipping in demanding work on medium steels. The CVD coating acts as a thermal and chemical barrier, which slows flank and crater wear and preserves the cutting edge under elevated temperatures. The insert’s 7° clearance angle and the cylindrical hole with a one‑sided countersink (40°–60°) provide secure seating and stable clamping forces in appropriate holders, reducing vibration. This results in longer tool life and fewer unexpected stoppages, improving overall process reliability and uptime. Seamless integration into productive turning systems Delivered as part of a system concept — holder, indexable inserts and spare parts — the insert is straightforward to integrate into existing tool setups. The round plate shape and hole style make mounting and rotation simple where indexable round inserts are already in use. For operators transitioning from conventional grades, the T9215 grade offers a pragmatic balance of productivity and robustness, suitable for series production where repeatable results matter. Technical teams appreciate the clear match between insert geometry and application: high‑feed roughing under stable clamping conditions, especially on medium‑strength steels. For high‑productivity roughing with proven wear resistance, contact Metav Werkzeuge for availability and application advice on the Tungaloy RCMT1204M0 T9215 insert — eMail: info@metav-werkzeuge.com or Telephone: +49 2822 7131930 Technical data Article number: 6772459 SKU: 6772459-Tungaloy Manufacturer SKU: TUN6772459 Manufacturer: Tungaloy Model series: TurnTenFeed Application: Turning Material: Carbide Numbers / Core technical data Plate size: 12 mm Plate thickness: 4.76 mm Clearance angle: 7° Corner radius: 0 mm Countersink angle: 40°–60° Special features / Versions Coating: CVD‑coated carbide (T9215) Insert shape: round Hole: with hole, cylindrical + one‑sided countersink Chipbreaker: single‑sided Typical use: high‑feed roughing, continuous to slightly interrupted cuts System: holder, indexable inserts and spare parts FAQ What materials is this insert intended for? The RCMT1204M0 T9215 insert from Tungaloy is intended primarily for medium steel machining and performs well in productive roughing operations. How does the T9215 grade improve productivity? The T9215 CVD‑coated carbide offers a balance of wear resistance and toughness that supports higher feeds and longer cutting cycles, enabling greater material removal rates with reduced downtime. Is the insert suitable for interrupted cuts? Yes. The grade and cutting geometry are specified for continuous to slightly interrupted cuts; however, stable clamping and correct parameters are essential for best results with interrupted cuts. What seating and clamping features does the insert provide? The round insert features a cylindrical hole with a one‑sided countersink (40°–60°) and a 7° clearance angle, which together support secure seating and consistent clamping in compatible holders. Which system components are recommended with this insert? The TurnTenFeed concept comprises holders, indexable inserts and spare parts; matching the insert with a compatible holder within this system ensures the intended performance. Manufacturer/Responsible: Tungaloy‑NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand‑new product from the manufacturer.
RCMT 1204M0 T9215 Wendeplatten - Tungaloy
Take advantage of the combination of CVD-coated carbide wear resistance, single-sided chipbreaker geometry and a compact 4.76 mm plate thickness for reliably productive high-feed roughing; order the insert directly via Metav Werkzeuge or consult the team for application-specific recommendations. RCMT 1204M0 T9215 turning insert for high-feed roughing — Tungaloy RCMT 1204M0 T9215 is a round turning insert designed for high-feed, productive roughing under stable clamping conditions and for use in the TurnTenFeed family. CVD-coated carbide for long tool life Single-sided chipbreaker for stable chips Round insert with hole and countersink 7° relief angle for secure cutting Maximise cycle time with high-feed roughing capability The CVD-coated T9215 carbide grade combines high wear resistance with good fracture toughness, making it a rational choice for medium steel applications and continuous to lightly interrupted cuts. By selecting this geometry and grade, manufacturers benefit from shorter cycle times and predictable tool life; the insert is optimised for productive roughing where feed per revolution is the primary productivity driver. The TurnTenFeed system concept supports efficient changeover between holders and inserts, reducing machine downtime and improving throughput. Predictable chip control and extended tool life A defined single-sided chipbreaker and the round plate profile promote consistent chip formation and evacuation, reducing the risk of built-up edge and process interruptions. This results in fewer unplanned stops and improved surface quality on rough-turned components. The combination of chip control and the CVD-coated carbide substrate provides a robust balance between wear resistance and breakage security, supporting sustained production and lower tooling cost per part. Simple integration into turning tool systems The insert uses an ISO 1204M0 designation and a with-hole design (cylindrical hole plus one-sided countersink 40°–60°), enabling secure clamping in a wide range of holders. With a plate thickness of 4.76 mm, a nominal size of 12 mm and a clearance or relief angle of 7°, the geometry is easy to incorporate into existing tool fixtures. The supply concept includes holders, indexable inserts and spare parts, so replacement and inventory management can be organised for continuous production. For applications requiring minor adjustments, the stable cutting behaviour simplifies parameter tuning on the machine. Contact Metav Werkzeuge for tailored machining advice on the RCMT 1204M0 T9215 turning insert and to arrange delivery via info@metav-werkzeuge.com or +49 2822 7131930 Technical data Article number: 6774052 SKU: 6774052-Tungaloy Manufacturer SKU: TUN6774052 Model series: TurnTenFeed Application: Turning Insert designation: RCMT1204M0 Grade: T9215 Core specifications Thickness: 4.76 mm Size: 12 mm Relief angle: 7° Corner radius: 0 mm Hole countersink angle: 40°–60° ISO: 1204M0 Features & materials CVD-coated carbide Round insert geometry, with hole (cylindrical + one-sided countersink) Single-sided chipbreaker Designed for high-feed roughing and medium steel Suitable for continuous to light interrupted cuts System includes holders, indexable inserts and spare parts Part of the TurnTenFeed turning family FAQ What materials is this insert suitable for? The RCMT 1204M0 T9215 insert is specified for medium steel machining; the CVD-coated carbide grade provides wear resistance and fracture toughness appropriate for such materials. How is the insert clamped and what is the hole type? The insert features a cylindrical hole with a one-sided countersink (40°–60°) that secures the RCMT 1204M0 in compatible TurnTenFeed holders for stable clamping. Can this insert be used for interrupted cuts? Yes, the T9215 grade and round geometry are suitable for continuous to light interrupted cuts, offering reliable performance under short interruptions. Which chip control features support process reliability? The single-sided chipbreaker and round profile provide consistent chip formation and evacuation, which contributes to dependable machining cycles with the RCMT 1204M0 insert. What should be considered when replacing an insert with SKU 6774052-Tungaloy? When fitting the replacement RCMT 1204M0 T9215 (SKU 6774052-Tungaloy), ensure the holder matches the ISO 1204M0 geometry, the clamping screw aligns with the countersink specification and cutting parameters are adapted to high-feed roughing. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
RCMT 1204M0 T9225 Wendeplatten - Tungaloy
Benefit from the combination of a robust T9225 grade, CVD-coated carbide durability and geometry tailored for high-feed, productive rough turning; order directly via Metav Werkzeuge or consult our specialists for application support. RCMT 1204M0 T9225 RCMT1204M0 — Tungaloy turning insert for high-feed roughing (CVD-coated carbide) A Tungaloy RCMT1204M0 T9225 indexable insert engineered for high-feed turning and productive roughing under stable clamping conditions. CVD-coated carbide for robust cutting Optimised for high-feed rough turning Single-sided chipbreaker, with hole 12 mm round insert, 4.76 mm thickness Increase throughput with controlled chip formation The TurnTenFeed family design prioritises high-feed material removal rates while maintaining predictable chip control. The CVD-coated carbide combination and the T9225 grade balance wear resistance and toughness, which is particularly advantageous during interrupted cuts or variable engagement. The integrated single-sided chipbreaker reduces long stringy chips and aids evacuation, translating into fewer machining interruptions and more consistent cycle times for roughing operations. Reliable performance across medium to heavy steel applications This cutting grade is specified for medium to heavy steel machining where variability in cutting conditions demands increased toughness. The insert’s substrate and coating provide a wear-resistant cutting edge while still offering sufficient impact tolerance; this results in improved tool life and repeatable surface outcomes when machining steels under elevated feeds. The technical balance means fewer insert changes and steadier production output for batch and series turning. Geometry and mounting designed for stability The round 12 mm insert form with a 4.76 mm thickness and a 7° relief angle gives the cutting edge a secure seating and an even load distribution in robust toolholders. The central hole with a cylindrical bore and a single-sided countersink (40°–60°) ensures stable clamping torque and precise location, reducing the risk of insert movement at high feed rates. The zero corner radius supports heavy material removal without unexpected stress concentrations at the cutting edge. Practical benefits for shop-floor integration As part of a system comprising holders, indexable inserts and spare parts, this insert supports straightforward logistics and inventory management. The compatibility with standard toolholders and the TurnTenFeed series focus means quick changeovers and predictable performance in production environments. Fewer worn edges and improved chip control contribute to lower machining downtime and a measurable uplift in process efficiency. Contact Metav Werkzeuge for tailored machining advice on the Tungaloy RCMT1204M0 T9225 insert and for availability: email info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: 6780681 Manufacturer SKU: TUN6780681 SKU: 6780681-Tungaloy Model series: TurnTenFeed Material: carbide Grade/coating: T9225, CVD-coated Facts Insert designation: RCMT1204M0 Insert form diameter: 12 mm Thickness: 4.76 mm Relief angle: 7° Corner radius: 0 mm Countersink angle: 40°–60° Special features Round insert form Single-sided chipbreaker Central cylindrical hole with single-sided countersink Optimised for high-feed rough turning under stable clamping System includes holders, indexable inserts and spare parts Typical application: turning (productive roughing) FAQ What materials is this insert suited for? The Tungaloy RCMT1204M0 T9225 insert is intended for medium to heavy steel machining where a tougher grade yields reliable performance. How does the chipbreaker affect machining? The single-sided chipbreaker on the RCMT1204M0 promotes short, controlled chips under high-feed roughing, reducing interruptions and easing chip evacuation. Is this insert compatible with standard holders? Yes, the RCMT1204M0 format and central hole with countersink are designed for secure clamping in common indexable turning holders used in the TurnTenFeed family. What are the main advantages of the T9225 grade? T9225 combines wear resistance with toughness, offering stable edge life in demanding steel applications and better tolerance to variable engagement conditions. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
RCMT 1204M0 T9225 Wendeplatten - Tungaloy
Take advantage of productive roughing and reliable chip control with a robust CVD-coated carbide grade designed for medium to heavy steel turning; order the insert directly via Metav Werkzeuge or consult the team for application support. RCMT1204M0 T9225 RCMT indexable insert for high-feed turning — Tungaloy The RCMT1204M0 T9225 is a turning indexable insert engineered for high-feed machining and productive roughing in stable clamping conditions. High-feed turning and productive roughing CVD-coated carbide grade T9225 for steels Single-sided chipbreaker for secure chip control Centre hole with 40°–60° countersink Maximised material removal for shorter cycle times The TurnTenFeed family of tools focuses on efficiency: the combination of a CVD-coated carbide substrate and a geometry tuned for high-feed roughing delivers higher removal rates with consistent tool life. The insert’s geometry promotes stable cutting under firm clamping, which reduces vibration and helps to maintain process stability. This results in fewer tool changes and a more predictable production flow, making the solution particularly valuable for job shops and production lines that require repetitive heavy turning operations. Secure chip control and robust edge performance Built on the universal T9225 grade, the insert provides increased toughness for interrupted cuts and variable engagement depths. The single-sided chipbreaker ensures controlled chip formation and evacuation when machining medium to heavy steel, improving surface finish and safety at higher feed rates. The CVD coating improves flank wear resistance while preserving the substrate’s ability to withstand shock loads, so edge integrity remains reliable over extended runs. Designed for system flexibility and straightforward integration The insert is compatible with a holder-and-insert system that includes spare parts for quick replacement and minimal downtime. Key dimensional features—12 mm seat size and 4.76 mm thickness—allow integration into common RCMT-compatible turning holders, and the central hole with a cylindrical bore plus a one-sided countersink (40°–60°) supports secure mechanical clamping. The geometry and grade combination is well suited for stable setups that demand productive roughing rather than delicate finishing operations. Practical benefits and operational considerations Choosing this insert supports a balance of economy and process reliability: the Grade’s toughness reduces the risk of premature chipping, while the coating contributes to consistent wear behaviour. For applications with fluctuating cut conditions or light interruptions, the insert maintains performance where harder but more brittle grades would fail. For further machining parameter optimisation or holder recommendations, Metav Werkzeuge can supply technical guidance tailored to the specific machine, material and clamping situation. Contact Metav Werkzeuge for tailored selection advice on the Tungaloy RCMT1204M0 T9225 insert and to arrange fast delivery or technical consultation. Technical Data Article number: 6780661 SKU: 6780661-Tungaloy Model series: TurnTenFeed Facts Plate size: 12 mm Plate thickness: 4.76 mm Clearance angle: 7° Corner radius: 0 mm ISO designation: 1204M0 Special features CVD-coated carbide grade T9225 Single-sided chipbreaker Round plate geometry With centre hole: cylindrical bore + one-sided countersink (40°–60°) Intended application: turning / productive roughing FAQ What materials is this insert suitable for? The RCMT1204M0 T9225 insert is formulated for medium to heavy steel machining and performs well in applications with intermittent cuts where toughness is required. Is the insert compatible with standard RCMT holders? Yes, the RCMT1204M0 geometry and 12 mm seat are compatible with common RCMT-indexed turning holders designed for this size and form factor. How does the T9225 grade affect tool life? The T9225 grade combines toughness and wear resistance; in the RCMT1204M0 configuration it reduces the risk of chipping under variable engagement while maintaining consistent wear characteristics. Can this insert be used for finishing operations? This insert is optimised for productive roughing and high-feed turning; for fine surface finishes, a finishing-grade geometry or different insert specification is recommended. What clamping conditions are recommended for best results? Stable mechanical clamping with minimal overhang and rigid holder setup yields the best performance for high-feed roughing with this insert. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
RCMT 1204M0 T9225 Wendeplatten - Tungaloy
Benefit from a CVD-coated T9225 grade and the productive TurnTenFeed concept for reliable high-feed roughing; the result is robust cutting performance and consistent metal removal under stable clamping. Order the RCMT1204M0 insert directly via Metav Werkzeuge or consult our specialists for tailored machining advice. RCMT 1204M0 T9225 RCMT turning insert by Tungaloy — CVD-coated carbide for high-feed roughing RCMT1204M0 T9225 is a round indexable insert for turning, engineered for high-feed, productive roughing where stable workholding and reliable edge life are priorities CVD-coated carbide T9225 for robust cutting performance Optimised for high-feed roughing in turning Round insert with cylindrical hole and chipbreaker Productivity gains for heavy roughing cycles The TurnTenFeed family is developed to boost throughput in demanding roughing operations. The CVD-coated T9225 grade combines toughness with wear resistance, which translates into longer tool life and fewer changeovers. As a round indexable insert, it provides stable cutting contact and predictable wear behaviour, simplifying process planning and reducing machine downtime. The design emphasises efficient chip control and repeatable performance under varying entry conditions, making it suitable for productive sequential cuts on robust setups. Broad material compatibility with steady edge life The chosen T9225 carbide composition is a universal, robust grade for medium to heavy steel machining and slightly interrupted cuts. This balance of hardness and toughness helps maintain a stable cutting edge when feed rates or cross-sections vary, which improves repeatability across production batches. Operators will notice consistent component tolerances and fewer rejects thanks to the insert’s capacity to bridge changing engagement conditions without premature edge failure. Geometry and clamping features that support stability The insert’s round shape and cylindrical hole with one-sided countersink (40°–60°) allow secure clamping and simple orientation in compatible holders. A single-sided chipbreaker guides swarf away from the cutting zone, improving surface quality and evacuation in heavy chip loads. The nominal 4.76 mm thickness and 12 mm size yield a solid contact area for heavy-duty cutting forces, while the 7° relief ensures dependable clearance to reduce rubbing and heat generation during sustained cuts. Practical machining benefits and process recommendations When paired with a rigid toolholder and consistent workholding, this indexable solution reduces cycle times and increases achievable metal removal rates. The RCMT1204M0 insert is best applied where high feed per revolution and aggressive depth of cut are required, under stable fixtures. Its robustness supports longer uninterrupted production runs and simplifies insert inventory planning by delivering a versatile grade for a variety of steel alloys. For best results, match holder geometry to the round insert form and monitor chip flow to maintain repeatable surface finish and tool life. Contact Metav Werkzeuge to discuss Tungaloy turning solutions including the RCMT1204M0 insert and to arrange technical guidance on integrating this grade into existing roughing processes; email info@metav-werkzeuge.com or call +49 2822 7131930 Technical Data Article number: 6781164 SKU: TUN6781164 Model series: TurnTenFeed Designation: RCMT1204M0 Manufacturer article number: 6781164 Facts Insert size: 12 mm Thickness: 4.76 mm Relief angle: 7° Corner radius: 0 mm Countersink angle: 40°–60° Special features Material: carbide (CVD-coated) Grade/coating: T9225 Shape: round Hole: cylindrical hole with one-sided countersink Chipbreaker: single-sided Application: turning; high-feed roughing Suited for medium–heavy steel and slightly interrupted cuts FAQ Which operations are best suited to this insert? The RCMT1204M0 Tungaloy indexable insert is optimised for high-feed roughing in turning operations, particularly where stable clamping supports aggressive metal removal. Which materials does the T9225 grade handle effectively? The T9225 CVD-coated grade performs reliably on medium to heavy steel, providing good wear resistance and toughness for slightly interrupted cuts. How is the insert secured in the holder? The round insert features a cylindrical hole with one-sided countersink (40°–60°) that allows secure clamping in compatible holders; refer to holder specifications to match the RCMT1204M0 (SKU TUN6781164). What geometry details are relevant for tool setup? Key dimensions include a 12 mm size, 4.76 mm thickness, 7° relief and 0 mm corner radius; these influence clamping, clearance and chip formation during roughing. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
Fragen zu diesen Produkten??
Mit mehr als 30 Jahren Erfahrung beraten wir Sie gerne persönlich.
Tel.: +49 2822 7131930
Mail: info@metav-werkzeuge.com