SNMG 120404 T9235 Wendeplatten - Tungaloy
Take advantage of a robust, CVD‑coated carbide grade for steels and the ISO SNMG geometry to maintain production reliability in unstable turning conditions; the insert’s double‑sided chipbreaker and 0.4 mm corner radius extend edge life and permit safer interrupted cuts. Order directly via Metav Werkzeuge or consult our machining specialists for grade and holder selection. SNMG120404 T9235 – ISO turning indexable insert for turning, Tungaloy The SNMG120404 T9235 is an ISO‑standard square indexable insert designed for external and internal turning, optimised for steel machining under lower cutting speeds and unstable or interrupted conditions. CVD‑coated carbide grade T9235 for steels Square SNMG120404 form with 90° entering angle 0.4 mm corner radius for robust edge strength Double‑sided chipbreaker for interrupted cuts Consistent cutting performance where stability is limited The CVD‑coated carbide composition of the grade T9235 is engineered for turning steel at reduced cutting speeds and in less stable setups. The chemical vapour deposition layer provides a hard, wear‑resistant surface that improves flank wear behaviour while the carbide substrate sustains toughness. In practice, this means a combination of stable chip formation and extended tool life when tool‑holder rigidity or intermittent cuts would otherwise cause rapid wear. The SNMG geometry contributes to predictable engagement with the workpiece, allowing process planners to favour reliability over aggressive cutting parameters. Seamless integration into ISO tool systems for repeatable setups As an ISO indexable insert, compatibility is determined by form, clearance angle, tolerance class, fastening method, size and thickness. The SNMG120404 format (square plate, 12 mm inscribed diameter) and the cylindrical centre hole ensure positive locating in matched toolholders and clamping sets. The listed thickness of 4.76 mm and the 90° entering angle give a stable seating that supports repeatable indexability and simple inventory handling. System components typically include the insert, the appropriate external holder or boring bar, a locating shim or clamping kit and replacement screws for fast reassembly. Practical benefits in everyday turning operations The double‑sided chipbreaker design enhances chip control for a wide range of steel turning tasks, improving surface finish and reducing rework. The 0.4 mm corner radius balances strength and finish capability: it resists edge chipping during interrupted cuts while still allowing respectable surface quality on lighter passes. Because the insert is indexable and double‑sided, flipping the cutting edges provides economical usage of the full insert life. These attributes make the component especially suited to shops requiring robust performance in mixed‑stability environments. Guidance for selection and process optimisation Select the T9235 grade and the double‑sided chipbreaker when machining steels where interrupted cuts or lower cutting speeds are expected. Match the SNMG120404 insert to a holder that fulfils the form, clearance and tolerance requirements to ensure correct seating; improper fit can negate the grade’s advantages. For optimised results, pair the insert with a holder that offers adequate rigidity and confirm the clamping torque and shim use specified by the holder manufacturer. For tailored cutting data or if machining atypical steels, consult technical specialists to refine speed and feed settings. For reliable turning of steels in unstable or interrupted conditions, contact Metav Werkzeuge to procure the Tungaloy SNMG120404 T9235 insert and obtain expert advice on holder compatibility and cutting‑data optimisation via info@metav-werkzeuge.com or +49 2822 7131930 Technical data Article number: 6785942 Manufacturer SKU: TUN6785942 SKU: 6785942-Tungaloy Label: SNMG120404 T9235 Tungaloy‑insert Manufacturer article number: 6785942 Manufacturer: Tungaloy Material: carbide Grade/coating: CVD‑coated T9235 Shape: square (SNMG) Size: 12 mm inscribed circle Thickness: 4.76 mm Corner radius: 0.4 mm Entering angle: 90° Clearance angle: 0° Hole: with cylindrical hole Chipbreaker: double‑sided Application: turning Core data Thickness: 4.76 mm Inscribed diameter: 12 mm Corner radius: 0.4 mm Entering angle: 90° Clearance angle: 0° Manufacturer article number: 6785942 Special features ISO SNMG120404 form CVD‑coated carbide grade T9235 Double‑sided chipbreaker for interrupted cuts Square plate geometry for 90° operations Cylindrical centre hole for positive location Suited to steel machining at lower cutting speeds Compatible with standard holders, shims and clamping kits Designed for external and internal turning applications FAQ What work materials are suitable for this insert? The SNMG120404 T9235 insert is formulated for steel machining; the CVD‑coated T9235 grade performs particularly well at lower cutting speeds and in interrupted cutting conditions. How does the chipbreaker affect machining? The double‑sided chipbreaker on this Tungaloy insert improves chip control and surface finish during turning operations and is beneficial where intermittent cuts occur. Is the SNMG120404 compatible with standard toolholders? The SNMG120404 follows ISO geometry; compatibility depends on matching form, clearance angle, tolerance and fastening method — correct holder choice ensures secure seating and repeatable results. Can the insert be indexed to use multiple cutting edges? Yes, the insert is double‑sided and indexable, allowing rotation or flipping to use additional cutting edges and extend productive life. What does the 0.4 mm corner radius mean for cutting performance? A 0.4 mm corner radius increases edge strength and resistance to chipping, making it suitable for heavier interrupted cuts while still allowing acceptable surface quality on finishing passes. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
SNMG 120404 T9235 Wendeplatten - Tungaloy
Benefit from the combination of a T9235 CVD-coated carbide grade and a 0.4 mm corner radius for dependable machining under interrupted or unstable cutting conditions; ISO conformity ensures straightforward integration into existing tool systems. Order this indexable turning insert directly via Metav Werkzeuge or consult our specialists for application support. SNMG120404 T9235 indexable turning insert – CVD-coated carbide, 90° geometry (Tungaloy) SNMG120404 T9235 is an ISO-format indexable insert designed for robust external and internal turning of steel components. CVD-coated carbide for increased wear resistance Designed for external and internal turning Square insert with 90° cutting geometry Double-sided insert with cylindrical hole Reliable cutting in interrupted and unstable conditions The SNMG120404 T9235 insert pairs a CVD-coated surface with a carbide substrate in the T9235 grade, prioritising toughness for operations where stability is limited. This composition is optimised for low cutting speed applications and situations with interrupted cuts, giving a controlled compromise between edge life and fracture resistance. The 0.4 mm corner radius helps distribute cutting forces and reduce chipping, while the 0° clearance combined with the 90° cutting geometry provides predictable engagement and consistent chip formation on steel workpieces. Easy integration with ISO tooling systems for repeatable results As part of the ISO family, the insert follows the ISO 120404 designation and is manufactured as a square insert with 4.76 mm thickness, a cylindrical hole and double-sided edges for indexing. These dimensional characteristics determine holder compatibility via form, relief angle, tolerance class, fastening method and size. When mounted in a correctly specified holder, together with an appropriate shim and clamping kit, the system delivers secure seating and repeatable positioning, simplifying programming and reducing setup variation across consecutive machining cycles. Improved productivity and predictable process behaviour The indexable insert design reduces tooling inventory and downtime by offering two usable cutting edges per insert; this contributes directly to lower cost per component and faster turnaround during tool changes. The combination of a robust grade and protective coating enhances stability in tougher turning operations, enabling longer uninterrupted runs and more consistent surface quality. Suitable for external and internal turning, the insert supports efficient machining strategies where a resilient grade covering a broad range of steel tasks is advantageous. For reliable steel turning under interrupted conditions choose the Tungaloy T9235 grade insert—contact Metav Werkzeuge for ordering and tailored application advice at info@metav-werkzeuge.com or by phone on +49 2822 7131930. Technical data SKU: 6785943-Tungaloy Manufacturer article number: 6785943 Manufacturer SKU: TUN6785943 Brand: Tungaloy Model series: ISO turning indexable inserts Facts Size: 12 mm Thickness: 4.76 mm Corner radius: 0.4 mm Relief angle: 0° Hole style: cylindrical hole Cutting angle: 90° Grade: T9235 Special features Material: Carbide Coating: CVD-coated Application: Turning (external and internal) Insert shape: square Double-sided insert for indexing System components: suitable holder, shim and clamping kit, spare screws FAQ What materials is this insert suitable for? The SNMG120404 T9235 insert is specified for machining steel and is particularly effective where a tough, CVD-coated carbide grade is required for interrupted or unstable cutting. How does the T9235 grade differ from harder grades? T9235 prioritises toughness over maximum hardness, so the Tungaloy T9235 grade resists chipping and fracture better at low cutting speed and under interrupted cutting, extending usable edge life in many steel applications. Which holder features are required to fit this insert? Compatibility depends on form, relief angle, tolerance class, fastening and size; ensure the chosen external or internal holder matches the ISO 120404 geometry and provides proper clamping for repeatable seating. How many edges are usable before replacement? The insert is double-sided, offering two cutting edges; indexing extends the serviceable life and reduces tool changes compared with single-edged alternatives. Can this insert be used for finishing operations? Yes; with its 0.4 mm corner radius and appropriate cutting parameters, the insert can achieve respectable surface quality while maintaining edge robustness, though final finish will depend on machine rigidity and cutting conditions. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
SNMG 120404 TH10 SNMG Wendeplatten - Tungaloy
Take advantage of the combination of precise ISO geometry, a sharp TH10 uncoated carbide grade and a secure clamping interface for efficient, low-force turning of non‑ferrous components. Order the SNMG120404 TH10 indexable insert directly via Metav Werkzeuge or consult our technical team for application support. SNMG120404 TH10 Turning Insert — Tungaloy The SNMG120404 TH10 is an ISO-format turning insert designed for external and internal turning, offering a sharp uncoated carbide grade optimised for non‑ferrous materials. ISO SNMG shape, 90° included angle Uncoated cemented carbide TH10 grade Double-sided chipbreaker for stable chips Cylindrical hole for secure clamping High-performance turning with reduced cutting forces The uncoated TH10 cemented carbide grade is formulated to deliver a low cutting force and a clean surface finish in non‑ferrous machining. This results in reduced spindle load and smoother feed behaviour during aluminium, brass and plastic turning. The combination of a sharp cutting edge and optimised chip control supports consistent cycle times, making the insert a pragmatic choice where machining efficiency and part integrity are priorities. Precision geometry for reliable toolholder compatibility The square SNMG geometry with a 90° included angle and a 0.4 mm corner radius provides predictable engagement and consistent part geometry. The insert is manufactured to ISO dimensions so compatibility with holders is determined by shape, relief angle, tolerance class, fastening method, size and thickness. The presence of a cylindrical hole and the standard thickness ensure secure clamping and repeatable positioning when used with the appropriate external holder or boring bar. Chip management and material suitability explained A double-sided chipbreaker is incorporated to promote controlled chip formation and evacuation at typical feeds for non‑ferrous materials. As an uncoated grade, the cutting edge avoids build‑up and is suitable where low cutting temperature and excellent surface appearance are required. The insert is therefore recommended for turning tasks on aluminium, brass and many plastics, and for applications where minimal burr and a fine finish are essential. Practical system benefits and shopfloor efficiency The ISO insert design supports a modular system: the insert works together with a matching external holder or boring bar, a shim/clamping set and standard replacement screws. This system approach simplifies inventory management and reduces downtime for indexation or replacement. Using ISO‑compliant inserts also facilitates fast changeover across machines and operators, contributing to improved process reliability and predictable production flow. For application advice or to source original Tungaloy SNMG120404 TH10 inserts, contact Metav Werkzeuge for technical consultation and supply — info@metav-werkzeuge.com / +49 2822 7131930 Technical data Article number: 6806662 Manufacturer SKU: TUN6806662 SKU: 6806662-Tungaloy Model series: ISO turning indexable inserts Application: Turning Facts ISO designation: 120404 Insert type: SNMG Size: 12 mm Thickness: 4.76 mm Relief angle: 0° Included angle: 90° Corner radius: 0.4 mm Special features Material: cemented carbide Grade/coating: TH10 (uncoated) Chipbreaker: double-sided Hole: with hole Hole style: cylindrical hole Shape: square FAQ What materials is this insert best suited for? The SNMG120404 TH10 insert from Tungaloy is optimised for non‑ferrous materials such as aluminium and brass, as well as various plastics where low cutting forces and a clean surface finish are required. Is the SNMG120404 compatible with standard ISO SNMG holders? Yes. The insert follows ISO dimensions, so compatibility depends on holder form, relief angle, tolerance class, fastening method, size and thickness; it is intended for standard SNMG toolholders and boring bars. How does the double-sided chipbreaker affect machining? The double-sided chipbreaker on this indexable insert promotes controlled chip formation and evacuation, improving surface quality and reducing the risk of built-up edge in suitable materials. Can the uncoated TH10 grade be used at high speeds? The TH10 uncoated cemented carbide grade is chosen for its low cutting forces and clean finish in non‑ferrous machining; cutting speed suitability should be assessed against the specific material, machine rigidity and coolant strategy. How many cutting edges are available per insert? The SNMG120404 is double-sided, providing multiple indexable edges; edge count depends on indexation practice and the specific insert geometry. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
SNMG 120408 AH110 Wendeplatten - Tungaloy
Benefit from the combination of a PVD-coated AH110 grade and a 0.8 mm corner radius for process-secure turning; compatible with ISO holders at 90° and available via Metav Werkzeuge or on request through our technical consultants. SNMG 120408 AH110 turning insert — PVD-coated carbide, 0.8 mm radius (Tungaloy) SNMG 120408 AH110 indexable turning insert for ISO-compliant external and internal turning, engineered for wear resistance and consistent edge stability in demanding machining tasks PVD-coated carbide grade AH110 0.8 mm corner radius for versatile edge strength Double-sided chipbreaker for repeatable cutting edges Square SNMG form with cylindrical hole and 4.76 mm thickness Improved cutting reliability and longer tool life The PVD-coated AH110 carbide grade delivers a measurable improvement in wear resistance and edge integrity during turning operations. As an indexable insert, this item provides repeatable cutting performance: the 0.8 mm corner radius combines robustness with a controllable cut geometry, reducing edge chipping in unstable setups. The double-sided chipbreaker supports consistent chip formation, so cycle times remain predictable and downtime for insert changes is reduced. These technical characteristics translate into lower process variability and increased productivity on medium-duty turning and finishing passes. Straightforward mounting and ISO compatibility Designed to the ISO SNMG geometry, the insert mounts easily in standard SNMG holders; compatibility depends on form, clearance angle, tolerance class, fastening method, size and thickness. The square form with a cylindrical hole and a plate thickness of 4.76 mm ensures stable clamping and straightforward replacement routines. A clearance angle of 0° and the standardised ISO designation simplify procurement and inventory management across workshops. Clear labelling and the ISO coding allow fast checks against holder specifications and minimise the risk of incorrect assembly. Application scope and practical recommendations Suitable for external and internal turning, this grade is intended where a sharp cutting edge and process security are required. Select the chipbreaker and grade to match the workpiece material, machining type and setup stability — the insert’s design supports reliable machining across a broad range of steels and cast materials when correctly paired. For best results, pair the insert with a suitably rigid holder and adjust feeds and speeds according to component rigidity; the combination of carbide substrate and PVD finish aids surface quality while maintaining tool life under interrupted cuts. For a tailored recommendation on using Tungaloy SNMG 120408 AH110 inserts in specific applications, contact Metav Werkzeuge for technical guidance or request material-specific advice by email or phone Technical Data Article number: 6806717 Manufacturer SKU: TUN6806717 Our SKU: 6806717-Tungaloy Facts ISO designation: 120408 Corner radius: 0.8 mm Plate size: 12 mm Plate thickness: 4.76 mm Clearance angle: 0° Special features Grade: AH110 Substrate: carbide Coating: PVD-coated Chipbreaker: double-sided Plate form: square (SNMG) Hole style: cylindrical hole Application: turning (external & internal) FAQ What materials is this insert suitable for? The SNMG 120408 AH110 insert by Tungaloy is formulated as a wear- and fracture-resistant grade suitable for a wide range of steels and common cast materials when the chipbreaker and cutting data are matched to the workpiece. How many usable edges does the insert provide? The square SNMG form with a double-sided chipbreaker offers multiple indexed edges; the SNMG 120408 AH110 turning insert (SKU 6806717-Tungaloy) allows economical rotation to fresh cutting edges as wear occurs. Is the insert compatible with standard SNMG holders? Yes — compatibility is ISO-based and determined by form, clearance angle, tolerance class, fastening, size and thickness; the SNMG 120408 AH110 is made for ISO-compliant SNMG holders. What are the main benefits of the AH110 grade and PVD coating? AH110 with a PVD coating on a carbide substrate improves edge life and process security, delivering consistent chip control and surface finish under a range of turning conditions. Does the insert require a specific fastening screw or clamp? Mounting requires the correct ISO SNMG holder and matching fastening hardware; the insert’s cylindrical hole and standard sizing facilitate secure clamping in compatible holders. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
SNMG 120408 AH120 Wendeplatten - Tungaloy
Take advantage of the combination of PVD‑coated carbide AH120, a 0.8 mm corner radius and ISO compatibility to ensure sharp cutting performance and high process security in turning operations; order the SNMG 120408 AH120 insert directly via Metav Werkzeuge or consult our technical team for application guidance. SNMG 120408 AH120 ISO turning insert — PVD‑coated carbide, 0.8 mm radius (Tungaloy) SNMG 120408 AH120 is an ISO‑standard insert for external and internal turning, engineered for stable cutting performance where a sharp cutting edge and machining reliability are required PVD‑coated carbide grade AH120 Corner radius 0.8 mm Double‑sided chipbreaker ISO SNMG 120408, 90° square insert Precision and process security for consistent turning The insert combines a PVD‑coated carbide body with the wear‑resistant AH120 grade to deliver a balance of longevity and edge integrity. The coating enhances surface hardness and reduces adhesion at the cutting edge, which translates into reduced flank wear and more predictable tool life. For machining processes where repeatable component quality and minimal downtime are priorities, this geometry supports a sharp cutting edge and consistent chip formation, helping to maintain dimensional accuracy across series production runs. Optimised geometry for reliable chip control An ISO‑conforming, 90° square configuration together with a double‑sided chipbreaker ensures controlled chip flow and versatile orientation options. The 0° clearance angle and 0.8 mm corner radius reduce radial forces while preserving corner strength; the result is improved stability during shoulder cuts and finishing passes. The presence of a cylindrical hole permits secure clamping in compatible holders, supporting repeatable seating and torque transmission. In practice, correct selection of the insert form and chipbreaker leads to fewer interruptions and more efficient cycle times. Clear guidance on system compatibility and setup Compatibility with a toolholder depends on the insert’s form, clearance angle, tolerance class, fastening method, size and thickness; this insert is designed to fit standard SNMG seatings when matched with the appropriate external holder or boring bar. The recommended system comprises the ISO insert, a matching outer holder or boring bar, the correct support plate or clamp set, and replacement screws for secure assembly. Specifying the holder that matches the insert’s square form and 4.76 mm thickness ensures correct clamping pressure and repeatable positioning for high‑precision turning. Application strengths and handling advice This turning grade is suited to operations that demand a balance between edge sharpness and resistance to chipping. The AH120 grade is tailored to maintain a robust cutting edge under conditions that would otherwise promote micro‑chipping, making it a practical choice for varied production tasks. For best results, select a chipbreaker and cutting parameters aligned to the workpiece material and rigidity of the machine setup; modest feeds with appropriate cutting speeds will leverage the insert’s wear properties while preserving surface finish and component tolerances. For machining tasks that require a dependable, wear‑resistant turning insert, contact Metav Werkzeuge to source the Tungaloy SNMG 120408 AH120 and obtain tailored application advice via info@metav-werkzeuge.com or by phone on +49 2822 7131930. Technical data Article number: 6814569 Manufacturer SKU: TUN6814569 Seller SKU: 6814569-Tungaloy Model series: ISO turning inserts Designation: SNMG120408 Grade: AH120 Facts Corner radius: 0.8 mm Insert size: 12 mm Thickness: 4.76 mm Relief/clearance angle: 0° Insert angle: 90° Special features PVD‑coated cemented carbide Double‑sided chipbreaker Square insert with cylindrical hole ISO‑standard geometry for holder compatibility Suitable for external and internal turning operations FAQ What is the primary advantage of the AH120 grade? The AH120 grade provides a wear‑resistant, chip‑secure cutting edge; the Tungaloy SNMG 120408 AH120 insert combines this grade with a PVD coating to enhance tool life and machining stability. Which holders fit the SNMG 120408 insert? Holders that accept ISO SNMG inserts with a 90° square seat, compatible clamp sets and the corresponding screw pattern will fit; holder selection must match the insert form, thickness and tolerance class. How does the double‑sided chipbreaker affect performance? The double‑sided chipbreaker offers consistent chip control and allows the insert to be indexed; this supports uninterrupted production and helps maintain surface finish quality under varying cutting conditions. Is the insert suitable for finishing passes? Yes — the 0.8 mm corner radius and sharp edge geometry make the insert appropriate for finishing when combined with appropriate feeds and cutting speeds, delivering good surface integrity and dimensional control. What spare parts are recommended for assembly? A matching support plate or clamp set and replacement screws are recommended to ensure secure seating and repeatable positioning of the insert during tool changes. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand‑new product from the manufacturer.
SNMG 120408 AH120 Wendeplatten - Tungaloy
Taking advantage of a PVD-coated carbide grade and a double-sided chipbreaker, this insert combines durable edge life with predictable chip control for turning operations; order via Metav Werkzeuge or request application guidance from their consultants. SNMG 120408 AH120 indexable turning insert for turning by Tungaloy The SNMG120408 AH120 is a square ISO turning insert designed for general external and internal turning with a focus on process security and a sharp, wear-resistant cutting edge. PVD-coated carbide for enhanced wear resistance Double-sided chipbreaker for versatile turning 0.8 mm corner radius, 90° square geometry ISO compatibility; cylindrical hole for secure clamping Stable cutting performance with a wear-resistant grade The combination of PVD-coated carbide and the AH120 grade provides a balance between a sharp cutting edge and resistance to flank wear, supporting consistent tool life under varied turning conditions. The coated substrate reduces abrasive wear and increases thermal stability during continuous cuts, which improves the predictability of the machining process. For operations requiring durable edges and steady chip formation, this geometry helps maintain dimensional accuracy and reduces the frequency of insert changes, contributing to uninterrupted production cycles. Rigid geometry for reliable chip control and strength A 0.8 mm corner radius paired with a 90° square format delivers mechanical strength at the cutting edge while permitting robust cutting parameters. The double-sided chipbreaker is optimised for both light and medium cuts and aids in breaking chips into manageable lengths, lowering the risk of long swarf and improving surface finish. The 4.76 mm thickness of the insert increases stiffness in the cutting zone, making it suitable for applications where vibration damping and edge stability are priorities. The cylindrical hole and standard fastening interface ensure secure clamping in ISO-compatible holders. ISO-series compatibility and practical application guidance The insert is part of the ISO turning inserts model series and is compatible with holders that match the insert form, clearance angle, tolerance class, clamping method, size and thickness. Typical uses include both outside and inside turning where a sharp, process-secure edge is required. Selection of the correct chipbreaker and grade should be aligned with the workpiece material and machining strategy. The SNMG120408 designation identifies the insert geometry and size so that correct holder and underlay selection is straightforward, reducing setup time and ensuring consistent interchangeability across machines. For trustworthy, productive turning with Tungaloy’s AH120 inserts, contact Metav Werkzeuge for availability and tailored application advice — info@metav-werkzeuge.com | +49 2822 7131930 Technical Data Article number: 6806765 Manufacturer SKU: TUN6806765 SKU: 6806765-Tungaloy Model series: ISO turning inserts ISO designation: SNMG120408 Grade/coating: AH120, PVD-coated carbide Material: carbide Facts Shape: square Size: 12 mm Thickness: 4.76 mm Corner radius: 0.8 mm Included angle: 90° Clearance angle: 0° Hole: with cylindrical hole Features Chipbreaker: double-sided Application: turning (external and internal) Compatibility determined by form, clearance, tolerance class, clamping, size and thickness Typical system: insert + suitable external holder or boring bar + underlay/clamping set + replacement screws FAQ What materials is this insert intended for? The SNMG120408 AH120 insert is designed as a wear- and break-resistant solution for turning applications; material-specific chipbreaker and grade selection should be made to suit the workpiece and machining strategy. How does the AH120 grade affect performance? The AH120 PVD-coated carbide grade provides a sharp cutting edge with improved wear resistance and process security, supporting consistent edge life under typical turning conditions. Is the insert reversible or single-use? This is a double-sided indexable insert; the double-sided chipbreaker allows turning on both sides, extending effective usage before replacement. What should be checked for holder compatibility? Compatibility is determined by insert form, clearance angle, tolerance class, clamping method, size and thickness; confirm that the holder matches the SNMG120408 geometry and the 4.76 mm thickness. Does the 0° clearance angle limit applications? The specified 0° clearance angle is a neutral geometry characteristic; holders and cutting conditions should be selected accordingly to ensure correct rake and clearance in specific turning tasks. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
SNMG 120408 AH120 Wendeplatten - Tungaloy
Take advantage of the combination of PVD-coated carbide AH120 for durable cutting edges and a 0.8 mm corner radius for precise contouring to maintain stable machining processes; order the insert directly via Metav Werkzeuge or ask their consultants for application-specific advice. SNMG 120408 AH120 Tungaloy indexable insert – ISO turning insert for external and internal turning The SNMG120408 AH120 Tungaloy insert is an ISO-standard square indexable insert designed for external and internal turning, featuring a 0.8 mm corner radius and a neutral clearance geometry. PVD-coated carbide AH120 for wear resistance Double-sided chipbreaker for consistent chip control 0.8 mm corner radius for accurate contour machining ISO SNMG 120408 square insert, 4.76 mm thickness Consistent, high-performance cutting with long tool life The combination of a PVD-coated finish and a wear-resistant carbide substrate makes this insert especially suited to operations where a sharp cutting edge and process security are required. The AH120 grade has been developed for reduced flank wear and resistance to chipping, which in practice translates to longer tool life and fewer interruptions on the shop floor. For production environments this means less time spent on tool changes and more predictable cycle times. Stable chip control and dimensional accuracy Equipped with a double-sided chipbreaker, the geometry promotes controlled chip formation and evacuation during both external and internal turning. The 0.8 mm corner radius supports accurate contouring and improves edge strength at interrupted cuts, reducing vibration and contributing to improved surface finish. Where surface quality and repeatability matter, the insert’s geometry supports consistent component tolerances across batches. System compatibility and practical setup guidance The insert is supplied in the ISO SNMG 120408 form and must be matched to a compatible holder. Compatibility is determined by form, clearance angle, tolerance class, fastening method, size and thickness; using the correct holder and clamping set ensures secure seating and optimal cutting conditions. The SNMG format features a square plate with a cylindrical hole, a 4.76 mm thickness, and an effective inscribed size of 12 mm, designed for standard ISO turning toolholders. When the insert is integrated into a properly configured system, process reliability and repeatable results are achieved with minimal adjustment. Contact Metav Werkzeuge today to discuss application-specific recommendations for Tungaloy AH120 inserts and ensure optimal tool selection for your turning processes. Technical data Article number: 6811957 Manufacturer SKU: TUN6811957 Supplier SKU: 6811957-Tungaloy Core data Grade: AH120 Insert designation: SNMG 120408 Corner radius: 0.8 mm Thickness: 4.76 mm Inscribed size: 12 mm Included angle: 90° Materials & features Material: carbide Coating: PVD-coated Chipbreaker: double-sided Plate form: square Hole: with cylindrical hole Clearance: 0° Application: turning Series: ISO turning indexable inserts FAQ What materials is this insert suitable for? The SNMG120408 AH120 Tungaloy insert is optimised for a broad range of materials where a wear-resistant PVD-coated carbide performs best; the AH120 grade excels when process security and a sharp cutting edge are required. How does the chipbreaker affect machining? The double-sided chipbreaker on this insert improves chip control and evacuation, helping to maintain stable cutting forces and consistent surface finish during turning operations with the SNMG 120408 geometry. Which holders are compatible with this ISO insert? Compatibility depends on holder form, tolerance class, fastening and dimensions; the SNMG 120408 format requires a matching ISO SNMG toolholder with corresponding clamping and clearance characteristics. What are the key dimensions to check before installation? Check the insert thickness (4.76 mm), inscribed size (12 mm), corner radius (0.8 mm), hole style (cylindrical) and the 90° included angle to ensure correct seating and clamping in the chosen holder. Is this an original Tungaloy product and how is it identified? Yes, this is an original Tungaloy indexable insert identified as SNMG120408 AH120 with article number 6811957 and supplier SKU 6811957-Tungaloy. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
SNMG 120408 AH120 Wendeplatten - Tungaloy
Benefit from the combination of PVD-coated carbide for high wear resistance and a 0° relief geometry that supports stable machining and predictable tool life; choose the matching chipbreaker and holder for optimal performance. Order the SNMG120408 AH120 insert directly via Metav Werkzeuge or ask our consultants for application advice. SNMG120408 AH120 Tungaloy turning insert — PVD-coated carbide, 0° clearance SNMG120408 AH120 is an ISO-class turning indexable insert intended for external and internal turning where a sharp cutting edge and process reliability are required PVD-coated carbide for high wear resistance Sharp cutting edge for consistent process security Double-sided chipbreaker for versatile chip control ISO-standard form with cylindrical hole for fitting Engineered for dependable, productive turning The SNMG120408 insert combines a PVD-coated surface with a robust carbide substrate to deliver consistent cutting performance under continuous production conditions. The coating improves surface hardness and thermal stability, which reduces flank wear and extends service intervals—resulting in longer tool life and fewer tool changes. This translates directly into higher machine utilisation and improved cost-efficiency per component when compared with uncoated or less optimised grades. Designed for straightforward integration and flexibility Compatibility is ensured by the ISO geometry and the insert’s square form, allowing confident pairing with a wide range of ISO holders and boring bars. The ISO-standard design, together with the cylindrical hole and fixation features, simplifies mounting and replacement in standard clamping systems. The double-sided chipbreaker provides the option to reverse or rotate the insert for renewed cutting edges, which supports uninterrupted production and predictable maintenance planning rather than frequent tooling adjustments. Geometry and coating explained for reliable results Key dimensions such as the radius 0.8 mm, 4.76 mm thickness and the 90° included angle influence both cutting forces and surface finish: a 0.8 mm nose radius balances edge strength and achievable finish, while the plate thickness enhances rigidity in heavy or interrupted cuts. The 0° clearance reduces side relief and is suited to operations where toolholder geometry and workpiece support allow neutral clearance; selection should match the machine setup and intended cutting strategy. The PVD coating enhances wear resistance and helps maintain a sharp cutting edge, particularly beneficial when process security and repeatable results are priorities. Practical selection advice for consistent performance For standard turning operations, select the AH120 grade when priority is given to wear resistance and resistance to chipping under moderate to demanding conditions. Match the chipbreaker style and grade to the workpiece material and the rigidity of the setup to ensure stable chip formation and reduce the risk of edge failure. In a typical system configuration the insert is used with an appropriate external holder or boring bar, clamped with a support pad and clamping set, and secured using the correct screws—spares should be kept on hand to minimise downtime and sustain production flow. Contact Metav Werkzeuge for tailored advice on integrating Tungaloy turning inserts into production; experts can recommend holder compatibility and optimised cutting parameters — eMail: info@metav-werkzeuge.com | Tel: +49 2822 7131930 Technical Data Manufacturer article number: 6810257 SKU: 6810257-Tungaloy Manufacturer SKU: TUN6810257 Facts Size: 12 mm Thickness: 4.76 mm Corner radius: 0.8 mm Relief angle: 0° Included angle: 90° Special features Grade: AH120 Coating: PVD-coated Material: carbide Shape: square Hole: cylindrical hole Chipbreaker: double-sided Model series: ISO turning indexable inserts Application: turning FAQ What materials is this insert suitable for? The AH120 grade is a wear- and chipping-resistant PVD-coated carbide designed for a broad range of steels and general turning tasks; confirm specific material compatibility when choosing chipbreaker and cutting data. How does the 0° relief affect performance? A 0° clearance reduces side relief and increases contact area between insert and workpiece, which may enhance stability in supported setups; selection should consider holder geometry and cutting conditions for the best results. Can the insert be indexed to a fresh cutting edge? Yes, the square, double-sided chipbreaker design allows indexing and rotation to restore a sharp edge, extending usable life and maintaining consistent cutting behaviour. What are the key dimensions to check for holder compatibility? Verify the ISO designation (SNMG 120408), the 12 mm size, 4.76 mm thickness, the cylindrical hole style and the corner radius 0.8 mm to ensure proper fit and secure clamping. Which system components are required for a complete setup? A typical system comprises the ISO insert, a matching external holder or boring bar, a support pad/clamp set and the appropriate replacement screws for secure fixation. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
SNMG 120408 AH6225 Wendeplatten - Tungaloy
Take advantage of the proven combination of ISO conformity, a PVD-coated carbide grade optimised for stainless steels and an economical, double-sided design for consistent productivity in medium turning operations. Order the inserts directly via Metav Werkzeuge or consult our technical advisors for holder compatibility and process tuning. SNMG120408 AH6225 Tungaloy turning insert — PVD-coated carbide, 0.8 mm corner radius The SNMG120408 AH6225 is an ISO-standard turning insert for external and internal turning, engineered for reliable machining of stainless steels under varying conditions. PVD-coated carbide AH6225 Universal grade for stainless steel machining ISO SNMG120408, square form, 90° included angle 0.8 mm corner radius, double-sided chipbreaker Consistent cutting performance for stainless steels The combination of a PVD-coated carbide substrate and the AH6225 grade delivers a sharp yet stable cutting edge, specially tailored for machining stainless steel grades. This balance reduces flank wear during medium cutting depths and when operating under changing conditions, thereby extending insert life and stabilising cycle times. The coating improves oxidation resistance at elevated temperatures, which supports reliable performance on parts where temperature spikes occur during turning. Geometry that improves chip control and surface finish The square SNMG form with a 90° included angle and a 0.8 mm corner radius provides predictable cutting engagement and a strong cutting corner for general turning tasks. The double-sided chipbreaker ensures repeatable chip formation and evacuation on both indexes, reducing the risk of built-up edge and improving surface quality. The term "included angle" refers to the approach angle of the insert; a 90° angle is particularly suited to general-purpose external and internal turning where robust cutting action and consistent profile control are required. System compatibility that reduces setup time and costs As an ISO-standard insert, the unit integrates into conventional holder systems where compatibility is determined by form, relief angle, tolerance class, clamping method, size and thickness. The cylindrical hole ensures secure clamping and straightforward indexing, while the double-sided design halves the effective cost per cutting edge compared with single-sided alternatives. This combination supports streamlined tool inventory and faster changeovers in mixed-production environments, making the solution economically attractive for batch and job-shop operations. The Tungaloy manufacturing pedigree contributes to a predictable tool life and stable chip formation across a broad range of stainless steel alloys. Contact Metav Werkzeuge for tailored selection of holders and process parameters for Tungaloy inserts, or request detailed compatibility advice by e‑mail at info@metav-werkzeuge.com or by phone at +49 2822 7131930 Technical data Article number: 6890620 SKU: 6890620-Tungaloy Manufacturer SKU: TUN6890620 Model series: ISO‑Drehwendeschneidplatten Material: carbide Dimensions & geometry Size: 12 mm Thickness: 4.76 mm Corner radius: 0.8 mm Included angle: 90° Hole: with hole Features & suitability PVD-coated carbide, grade AH6225 ISO designation SNMG120408 Square plate, double-sided chipbreaker Cylindrical hole for secure clamping Intended for turning (external and internal), medium machining FAQ What materials is this insert suited for? The SNMG120408 AH6225 insert is designed primarily for machining stainless steels and performs well under the medium cutting conditions described for the AH6225 grade. How does the PVD coating benefit cutting operations? The PVD coating on the AH6225 grade enhances oxidation resistance and wear behaviour, which supports longer tool life and consistent cutting performance for stainless steel turning. Is this insert compatible with standard SNMG holders? Yes; the SNMG120408 follows the ISO SNMG form and integrates with compatible external and internal turning holders, subject to matching form, relief angle and clamping method. What advantage does the double-sided design provide? Double-sided indexing supplies two usable cutting edges per insert face, effectively reducing tooling costs per edge and simplifying inventory management. Which industries typically benefit from this insert? The insert is suitable for manufacturing sectors that require reliable stainless steel turning in medium operations, including general engineering, component production and maintenance workshops. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
SNMG 120408 AH6225 Wendeplatten - Tungaloy
Benefit from the combination of a PVD-coated carbide grade and a 0.8 mm corner radius for stable medium turning of stainless steels; the ISO compatibility ensures straightforward integration into existing turning tool systems. Order the insert directly via Metav Werkzeuge or consult the technical advisors for application-specific setup. SNMG 120408 AH6225 turning insert — PVD-coated carbide, 0.8 mm radius (Tungaloy) The SNMG120408 AH6225 is an ISO-standard square indexable insert engineered for reliable external and internal turning of stainless steels in medium cutting conditions. PVD-coated carbide for extended edge life Universal grade optimised for stainless steels 0.8 mm corner radius for robust edge performance ISO square insert with cylindrical hole Consistent medium turning and predictable tool life The combination of a PVD-coated carbide substrate and the AH6225 cutting grade delivers a balance of sharpness and edge stability that suits medium material removal in variable conditions. The 0.8 mm corner radius reduces the tendency for edge chipping while maintaining a finish suitable for subsequent operations. This translates into more predictable tool life per index and fewer unscheduled tool changes, supporting smoother shop-floor throughput and reduced machining downtime. Clear compatibility and simple selection for holders Compatibility is governed by the insert’s geometry and dimensions: ISO-standard form, a 90° cutting angle, a 4.76 mm plate thickness and the central cylindrical hole for secure clamping. The relief specification (relief angle 0°) and tolerance class determine which external holders and boring bars are suitable; matching these parameters avoids runout and ensures repeatable results. For technicians less familiar with holders, the compatibility criteria allow straightforward selection from existing holder inventories without trial-and-error. Improved surface quality and efficient chip control The double-sided chipbreaker and the insert’s edge geometry promote reliable chip control during stainless steel turning. The double-sided chipbreaker minimises re-cutting of chips and reduces the heat concentration at the cutting edge, which helps achieve a consistent surface finish even under changing cutting conditions. Using a universal grade tailored to stainless steel reduces the need for multiple dedicated grades, simplifying tool management while maintaining process stability. Practical system advantages and economical use As part of an ISO insert system, the plate is intended to be used with a matching external holder or boring bar together with a shim or clamping set and spare screws. The double-sided design effectively doubles the number of usable cutting edges per insert, improving cost-efficiency per edge. Where production repeatability and quick index changes matter, the ISO format and stable grade characteristics enable faster set-ups and less scrap, which supports leaner operations and better overall productivity. For application advice or to order the Tungaloy SNMG120408 AH6225 turning insert, contact Metav Werkzeuge — info@metav-werkzeuge.com or call +49 2822 7131930 — for rapid consultation and delivery options. Technical data Article number: 6947304 SKU: 6947304-Tungaloy Manufacturer SKU: TUN6947304 Model series: ISO turning inserts Material: Carbide Grade: AH6225 Coating: PVD Core data ISO designation: SNMG120408 Size: 12 mm Thickness: 4.76 mm Corner radius: 0.8 mm Cutting angle: 90° Relief angle: 0° Special features Double-sided chipbreaker Square insert with cylindrical hole Universal for stainless steel machining Sharp yet stable cutting edge for medium cutting ISO-standard compatibility with holders and shims FAQ What materials is this insert best suited to machine? The SNMG120408 AH6225 turning insert is a universal grade optimised for stainless steel, providing a stable cutting edge and good process security for medium turning operations. How is the insert mounted and secured in a holder? The square ISO form with a central cylindrical hole requires a compatible external holder or boring bar and a matching shim/clamping set; the SNMG120408 format and dimensions ensure secure, repeatable clamping. Can the insert be re-indexed and how many usable edges are available? The plate is double-sided with a chipbreaker on each face, allowing re-indexing to multiple cutting edges and thus improving cost efficiency per insert. What are the key dimensions to check before ordering holders? Check the ISO designation SNMG120408, plate size 12 mm, thickness 4.76 mm and corner radius 0.8 mm; also confirm the relief angle 0° and the 90° cutting angle to match the holder geometry. Why choose a PVD coating for this application? A PVD coating on carbide increases wear resistance and helps maintain a sharp, stable edge when machining stainless steel, reducing edge deterioration under medium cutting conditions. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
SNMG 120408 AH6225 Wendeplatten - Tungaloy
Combining a PVD-coated carbide grade and a 0.8 mm corner radius, this insert provides a sharp yet stable cutting edge for reliable performance in rostfreier Stahl turning. Benefit from ISO compatibility and a double-sided chipbreaker for efficient chip control; order directly via Metav Werkzeuge or ask our consultants for selection help. SNMG120408 AH6225 Tungaloy turning insert — PVD-coated carbide, 0.8 mm radius The SNMG120408 AH6225 Tungaloy is an ISO-standard square turning insert designed for external and internal turning, optimised for rostfreier Stahl and similar alloys. PVD-coated carbide grade AH6225 Universal grade for rostfreier Stahl Square insert with 90° cutting geometry Double-sided chipbreaker and cylindrical hole Consistent cutting performance for rostfreier Stahl machining The SNMG120408 AH6225 insert pairs a PVD-coated surface with a wear-resistant carbide substrate to balance a sharp cutting edge and stable edge life. The AH6225 grade is formulated as a universal option for rostfreier Stahl, delivering reliable results under medium machining conditions and when process variables change. The PVD coating reduces adhesion and increases resistance to built-up edge, which translates into longer tool life and steadier component quality over production runs. Seamless integration into ISO tool systems for fast setup As an ISO-standard SNMG insert, compatibility with holders is determined by form, clearance angle, tolerance class, fastening type, size 12 mm, and 4.76 mm thickness. The square shape and 90° cutting geometry simplify set-up for facing and external turning, while the 0.8 mm corner radius supports both light finishing and modest stock removal without sacrificing surface integrity. Clear specification of geometry and dimensions enables easier tool management and predictable repeatability across tool changes. Effective chip control and flexible application range The double-sided chipbreaker design allows two usable cutting edges per side and contributes to controlled chip formation in variable conditions. For workshops facing mixed batches or changing stability, the combination of chipbreaker geometry and the AH6225 grade aids reliable chip evacuation and reduces the risk of workpiece damage. Selecting this insert supports a balance between productivity and surface finish when machining rostfreier Stahl or comparable materials. Practical selection and system considerations for durable results For optimal performance, pair the insert with a matching external holder or boring bar and ensure secure clamping with the correct shim and screw set. The insert’s cylindrical hole supports precise centring and stable fastening, helping to maintain repeatable tool position. When choosing cutting parameters, account for workpiece rigidity and coolant strategy to exploit the PVD-coated carbide benefits while extending tool life. If uncertainty remains about holder compatibility or grade selection, technical advice is available to match the insert to the machining scenario and stability conditions. For detailed application advice on Tungaloy inserts and to confirm holder compatibility for rostfreier Stahl turning, contact Metav Werkzeuge at info@metav-werkzeuge.com or call +49 2822 7131930 — our consultants will assist with selection and availability. Technical data Article number: 6825967 SKU: 6825967-Tungaloy Manufacturer SKU: TUN6825967 Model series: ISO-Drehwendeschneidplatten Designation: SNMG120408 AH6225 Tungaloy turning insert Application: Drehen Dimensions & core data Corner radius: 0.8 mm Size: 12 mm Thickness: 4.76 mm Clearance angle: 0° Cutting angle: 90° ISO code: 120408 Materials & features Material: carbide (Hartmetall) Coating: PVD Grade: AH6225 Chipbreaker: double-sided Hole: with cylindrical hole Shape: square System notes: compatibility by form, clearance angle, tolerance, fastening, size and thickness FAQ What materials is this insert suitable for? The SNMG120408 AH6225 insert is designed primarily for rostfreier Stahl and performs well with similar stainless alloys thanks to its PVD-coated carbide grade. Which insert geometry and dimensions define compatibility with holders? Compatibility depends on the SNMG120408 ISO geometry: size 12 mm, 4.76 mm thickness, 90° cutting angle and 0° clearance; holders matching these specifications ensure correct fit. How does the AH6225 grade behave under varying machining conditions? AH6225 offers a balanced combination of a sharp, stable cutting edge and wear resistance, providing consistent performance in medium machining and changing process conditions. What is the purpose of the cylindrical hole in the insert? The cylindrical hole enables secure centring and fastening in the seat, improving repeatability and stability of the insert during turning operations. Can the insert be used on both external and internal turning? Yes, the square SNMG form and robust chip control make it suitable for both external and internal turning when paired with appropriate holders and parameters. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
SNMG 120408 AH6225 Wendeplatten - Tungaloy
Take advantage of the combination of a PVD‑coated AH6225 grade, a stable cutting edge, and ISO compatibility for consistent turning performance; order the SNMG120408 AH6225 insert directly via Metav Werkzeuge or consult our specialists for application advice. SNMG 120408 AH6225 square indexable insert for turning (Tungaloy) SNMG120408 AH6225 is a square ISO indexable insert for external and internal turning, engineered for reliable performance on stainless steels PVD-coated carbide grade AH6225 Universal grade for stainless steels Double-sided chipbreaker design Square 12 mm plate, 90° cutting angle Increased productivity through a stable cutting edge The combination of a PVD-coated surface and a carbide substrate provides a balance of wear resistance and edge sharpness that supports medium‑duty turning operations. The AH6225 grade is formulated as a universal solution for stainless steels, so the insert maintains a consistent cutting edge under variable cutting conditions; this reduces the need for frequent tool changes and improves uptime. Where process reliability matters, the insert’s coating reduces adhesion and flank wear, helping to extend tool life while preserving part quality. Precise geometry for predictable results With a square form and a nominal 90° cutting angle, the insert delivers predictable tool paths for both external and internal turning. The 0.8 mm nose radius supports a good compromise between surface finish and edge strength, allowing stable performance on interrupted cuts while still enabling fine surface quality. The cylindrical hole and standard ISO dimensions ensure compatibility with common holders; insert clamping is determined by form, clearance, tolerance class, fixation, size and thickness, supporting straightforward integration into existing tool systems. Versatile chip control for cleaner production Equipped with a double-sided chipbreaker, the insert offers improved chip formation across a range of feeds and depths. The chipbreaker geometry helps to control swarf formation when machining ductile alloys such as stainless steels, decreasing the risk of chip entanglement and facilitating safer, cleaner production. Selecting the appropriate chipbreaker and grade according to workpiece material and machining stability delivers tangible benefits in process efficiency and surface integrity. Practical fitment and handling advantages The insert’s 4.76 mm thickness and 12 mm plate size conform to ISO standards, simplifying inventory management and replacement procedures. Being double-sided, each insert offers two usable cutting edges per side before indexing, which enhances cost efficiency in high‑volume shops. The insert is supplied in the SNMG 120408 format, making it straightforward to match with compatible external holders or tool shanks for turning tasks. Contact Metav Werkzeuge for tailored recommendations on holder compatibility and batch supply of the Tungaloy SNMG 120408 AH6225 insert; technical queries may be directed to Metav Werkzeuge via info@metav-werkzeuge.com or +49 2822 7131930 Technical data Article number: 6947277 Manufacturer SKU: TUN6947277 Model series: ISO turning indexable inserts Designation: SNMG120408 AH6225 Tungaloy‑indexable insert Material: carbide Coating: PVD Grade: AH6225 Numbers Nose radius: 0.8 mm Plate thickness: 4.76 mm Plate size: 12 mm Cutting angle: 90° Manufacturer article number: 6947277 Special features Square plate, double-sided chipbreaker Cylindrical mounting hole ISO‑compliant dimensions for standard holders Suited for external and internal turning FAQ What materials is this insert suited for? The SNMG120408 AH6225 insert is designed primarily for stainless steels and performs well under medium cutting conditions typical for turning operations. How does the AH6225 grade affect tool life and finish? The AH6225 PVD‑coated grade provides a balance of edge sharpness and wear resistance, which supports longer tool life and consistent surface finishes in production turning. Is the insert compatible with standard ISO holders? Yes, the SNMG120408 format and cylindrical hole follow ISO conventions; compatibility depends on holder form, clearance angle, tolerance class, fixation, size and thickness. How many cutting edges are available per insert? The square, double‑sided design provides multiple usable edges; indexing extends the service life and enhances cost efficiency. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
SNMG 120408 AH6225 Wendeplatten - Tungaloy
Take advantage of a universally applicable, PVD-coated carbide grade that combines a sharp, stable cutting edge with proven chip control; this results in robust performance for medium turning tasks and reliable process stability. Order genuine Tungaloy SNMG120408 AH6225 indexable inserts or consult Metav Werkzeuge for tailored machining advice. SNMG 120408 AH6225 Tungaloy indexable turning insert — PVD-coated carbide, square 90° geometry for turning SNMG120408 AH6225 Tungaloy-Wendeplatte is an ISO-format indexable insert designed for external and internal turning of stainless steels, offering a balanced edge for medium cutting conditions PVD-coated carbide grade AH6225 Universal for stainless steels Square SNMG 90° geometry Double-sided chipbreaker with cylindrical hole Consistent performance for stainless steel turning The SNMG120408 AH6225 indexable insert is designed to deliver consistent performance when machining stainless steels. The PVD-coated carbide substrate provides a sharp yet stable cutting edge, which reduces edge breakdown and keeps surface finish consistent across interrupted cuts. The integrated chip control geometry helps evacuate chips reliably, lowering the risk of re-cutting and minimising downtime. For production environments that demand repeatable results, the combination of coating and substrate translates into improved process stability and predictable tool life. Easy integration and standardised compatibility Thanks to the ISO designation and square SNMG format, the insert fits common ISO-compatible tool holders and boring bars without extensive adaptation. The standardised geometry — including the 90° corner configuration and the cylindrical hole for secure fastening — simplifies tool management and stockkeeping. This harmonisation reduces setup time and makes the insert straightforward to replace during routine index changes, supporting uninterrupted machining flow and efficient inventory management. Clear guidance on cutting behaviour and benefits The insert’s corner radius 0.8 mm and relief angle 0° balance cutting-edge strength and surface quality: a larger radius gives enhanced edge robustness for moderate depths of cut, while the geometry still permits good surface finish where required. The double-sided design offers two usable edges per index, which extends service intervals and contributes to cost-efficiency in batch production. When selecting parameters, pair the grade with moderate feed rates and appropriate coolant strategy to exploit the alloy’s wear resistance and maintain consistent results. Durable, economical choice for everyday turning With a PVD coating over a wear-resistant carbide substrate, this insert is optimised for longevity under varying conditions typical of stainless steel machining. The grade’s formulation aims for stable chip formation and reliable edge life, which reduces the frequency of index changes and lowers indirect operational costs. Backed by Tungaloy’s manufacturing standards, the insert supports productive machining with fewer interruptions — an advantage for job shops and production cells seeking to improve throughput while retaining surface quality. For application-specific recommendations or to source genuine Tungaloy SNMG120408 AH6225 indexable inserts, contact Metav Werkzeuge’s technical team: eMail info@metav-werkzeuge.com or phone +49 2822 7131930 — Metav Werkzeuge provides practical advice and fast availability for industrial turning applications. Technical data Article number: 6947328 Manufacturer SKU: TUN6947328 SKU: 6947328-Tungaloy Manufacturer item no.: 6947328 Model series: ISO turning indexable inserts Material: carbide Facts Insert designation: SNMG120408 Grade / coating: AH6225, PVD-coated carbide Size: 12 mm Thickness: 4.76 mm Corner radius: 0.8 mm Relief angle: 0° Geometry angle: 90° Special features Square insert with cylindrical hole Double-sided chipbreaker Suitable for external and internal turning Universal grade for stainless steels Compatible with ISO tool holders FAQ What materials is this insert best suited for? The SNMG120408 AH6225 insert is intended primarily for stainless steels; the AH6225 PVD-coated carbide provides balanced cutting behaviour for medium turning operations. How many cutting edges are available per insert? The square, double-sided design provides two indexed cutting edges per side, allowing multiple repositions before disposal and extending overall service intervals for the insert. What does the corner radius mean for my parts? A corner radius of 0.8 mm increases edge robustness and helps achieve a consistent surface finish under moderate depth-of-cut conditions when using the SNMG insert. Is the insert compatible with standard ISO holders? Yes. The ISO SNMG format, cylindrical hole and standardised dimensions enable compatibility with commonly used ISO turning holders and boring bars. Which features support chip control on this grade? The integrated double-sided chipbreaker geometry and the PVD-coated substrate promote reliable chip formation and evacuation, reducing the risk of tangling or re-cutting. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
SNMG 120408 AH6225 Wendeplatten - Tungaloy
Take advantage of a PVD-coated AH6225 grade that combines a sharp, stable cutting edge with broad process reliability for rostfreier Stahl; the ISO-format square geometry and 0.8 mm corner radius ensure predictable results in medium turning operations. Order directly via Metav Werkzeuge or consult our specialists for application support. SNMG 120408 AH6225 ISO indexable turning insert — PVD-coated carbide, 0.8 mm radius (Tungaloy) The SNMG120408 AH6225 is an ISO-format square indexable insert for external and internal turning, optimised for machining rostfreier Stahl and medium-duty operations. PVD-coated carbide grade AH6225 Optimised for rostfreier Stahl machining Square ISO insert, 12 mm size, 90° angle Double-sided chipbreaker, 0.8 mm corner radius Reliable cutting performance for rostfreier Stahl The PVD-coated AH6225 grade provides a balance between a sharp cutting edge and edge stability, making it suitable for variable conditions encountered when machining rostfreier Stahl. The PVD layer improves wear resistance and reduces adhesion, which in turn helps maintain dimensional accuracy over a longer tool life. As an ISO-formatted insert, it supports predictable repeatability in serial production; the combination of carbide substrate and surface coating is designed to reduce flank wear during medium turning, helping to sustain cycle times and part quality. Consistent chip control and edge life for medium turning Equipped with a double-sided chipbreaker, this insert promotes controlled chip formation and evacuation during both external and internal turning. The geometry supports stable cutting at moderate feeds and depths of cut, while the 0.8 mm corner radius gives a compromise between edge strength and surface finish. A double-sided design effectively doubles the usable cutting edges per index, reducing downtime for regrinding or replacement and improving overall process economy by increasing usable edge count. ISO compatibility and straightforward tool integration The insert is manufactured to ISO dimensions, so compatibility with holders depends on the matching of form, relief (0°) and tolerance class, clamping system, size and thickness. With a 12 mm size, 4.76 mm thickness and a square plate form, it fits standard square-holding systems that accept a cylindrical-hole clamping arrangement. Describing these parameters clearly facilitates correct holder selection and avoids assembly errors; the standardised format supports rapid replacement and predictable set-up in existing tool systems without complex adaptations. Contact Metav Werkzeuge for application advice and stock availability of the Tungaloy PVD-coated AH6225 grade; technical consultants are available by email at info@metav-werkzeuge.com or by phone on +49 2822 7131930 Technical data Manufacturer article no.: 6947290 SKU: 6947290-Tungaloy Manufacturer SKU: TUN6947290 Brand: Tungaloy Model designation: SNMG120408 Grade: AH6225 Material: carbide Coating: PVD Core specifications Insert size: 12 mm Thickness: 4.76 mm Corner radius: 0.8 mm Relief angle: 0° Included angle: 90° Special features ISO turning indexable insert Square plate form with cylindrical hole Double-sided chipbreaker Universal grade for rostfreier Stahl Designed for external and internal turning FAQ What materials is this insert best suited for? The SNMG120408 AH6225 insert is optimised for machining rostfreier Stahl and offers reliable performance across a range of stainless grades thanks to the PVD-coated carbide grade. How does the double-sided chipbreaker influence productivity? The double-sided chipbreaker on this Tungaloy indexable turning insert provides controlled chip formation and doubles the available edges per index, reducing changeover frequency and improving overall process economy. Which holder characteristics must be checked for compatibility? Compatibility depends on holder form, relief angle, tolerance class, clamping method, insert size and thickness; the ISO-format SNMG120408 requires a matching square holder with a cylindrical-hole clamping system. Is the AH6225 grade suitable for variable cutting conditions? Yes. The AH6225 PVD-coated grade is engineered to balance a sharp cutting edge with stability under changing conditions typical in medium turning operations. Can this insert be used for internal turning as well as external turning? Yes. The insert’s geometry and chipbreaking design make it suitable for both external and internal turning, provided the correct holder and clearance are used. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
SNMG 120408 AH6225 Wendeplatten - Tungaloy
Take advantage of the combination of a PVD-coated carbide grade (AH6225), an ISO SNMG120408 geometry and a 0.8 mm corner radius to achieve stable, repeatable turning of stainless steel under varying conditions; order directly via Metav Werkzeuge or request application advice from the technical team. SNMG120408 AH6225 – Turning insert for turning, Tungaloy The SNMG120408 AH6225 is an ISO-indexable turning insert engineered for external and internal turning, offering a balance of a sharp cutting edge and edge stability for medium cutting conditions. PVD-coated carbide AH6225 Universal for stainless steel 0.8 mm corner radius ISO SNMG 120408, 4.76 mm thick Consistent cutting performance for stainless steel machining The grade combines a PVD-coated surface with a wear-resistant carbide substrate to provide a predictable and durable cutting edge. Designed as a universal grade for stainless steel, AH6225 delivers a sharp cutting action while maintaining edge stability during interrupted cuts and variable feeds. The result is improved process reliability and reduced scrap rates because tool life is extended and surface finish is more consistent. The inclusion of a well‑matched chipbreaker aids in chip control for both finish and semi‑finishing operations, so cycle times can be optimised without compromising component quality. Geometry and holder compatibility that reduce set-up time The insert’s SNMG120408 geometry and square form (12 mm inscribed size) are ISO‑standardised to simplify toolholder selection: compatibility is determined by shape, relief, tolerance class, clamping and thickness. With a 0° relief angle and a 0.8 mm corner radius, the insert is suited to stable medium‑duty turning where a balance between strength and edge acuity is required. The plate is double‑sided and 4.76 mm thick, with a cylindrical central hole for secure clamping; these features make indexing straightforward and cost‑effective, as each edge can be used before replacement, lowering unit tooling costs. Practical benefits on the shop floor and support options By combining a stable cutting edge with a double-sided chipbreaker, this insert reduces the frequency of insert changes and supports consistent surface finishes on rotational parts. The indexable design also simplifies inventory management and lowers per‑part tooling cost. For machining scenarios with variable stability or mixed batches, the AH6225 grade is a pragmatic choice that balances tool life and cutting performance. If application certainty is required, Metav Werkzeuge offers technical guidance and can supply detailed cutting data or offer sample inserts for trial runs; contact details are provided below for tailored recommendations. Contact Metav Werkzeuge for application guidance on the Tungaloy SNMG120408 AH6225 insert, data‑sheet requests or sample availability via info@metav-werkzeuge.com or by telephone on +49 2822 7131930 Technical data Article number: 6947274 SKU: 6947274-Tungaloy Manufacturer SKU: TUN6947274 Manufacturer: Tungaloy Model series: ISO indexable turning inserts Material: carbide Facts Insert size: 12 mm Thickness: 4.76 mm Corner radius: 0.8 mm Relief angle: 0° Included angle: 90° Special features ISO designation: SNMG120408 Grade/coating: AH6225, PVD-coated Plate form: square Hole: with cylindrical hole Chipbreaker: double-sided Typical application: turning (external and internal) FAQ Which materials is this insert designed for? The AH6225 grade is designed as a universal solution for machining stainless steel, offering a balance of sharpness and edge stability for medium operations. How is compatibility with a toolholder ensured? Compatibility is determined by the insert’s form, relief angle, tolerance class, clamping method, size and thickness; the ISO SNMG120408 designation simplifies selection for matching holders and boring bars. What advantages does the AH6225 grade provide? The AH6225, a PVD-coated carbide grade from Tungaloy, provides a sharp yet robust cutting edge suited to varying conditions and helps extend usable tool life while maintaining surface quality. Can this insert be used for internal and external turning? Yes — the SNMG120408 geometry and double-sided chipbreaker are suitable for both external and internal turning applications, offering reliable chip control in typical turning operations. How many cutting edges are available per insert and how is indexing achieved? The insert is double-sided and indexable; each side provides multiple usable edges, and the central cylindrical hole with appropriate clamping hardware enables secure indexing and repeatable seating. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
SNMG 120408 AH6225 Wendeplatten - Tungaloy
Take advantage of the combination of a sharp, stable cutting edge and a universal PVD-coated carbide grade for productive turning of stainless steel; order the insert via Metav Werkzeuge or consult our technical advisors for cutting data and holder compatibility. SNMG 120408 AH6225 Turning insert by Tungaloy SNMG120408 AH6225 is a square ISO-standard turning insert optimised for medium-duty external and internal turning, particularly suited to stainless steel with a 0.8 mm corner radius and a 90° geometry. PVD-coated carbide grade AH6225 ISO SNMG 120408 format Optimised for stainless steel machining Double-sided, economical indexable insert Consistent cutting performance for stable production The PVD-coated carbide composition of this ISO-format insert delivers a sharp yet durable cutting edge, designed to resist short-term thermal peaks and maintain dimensional stability during medium machining. The AH6225 grade targets applications where a balance between edge life and surface finish is required. As an indexable insert with a 0.8 mm corner radius, the component offers predictable cutting forces that help to reduce vibration and promote repeatable part quality, which in turn supports reliable cycle times on conventional and CNC lathes. Engineered for stainless steel and mixed conditions This turning geometry is specifically prepared for working with stainless steel, where chip control and edge integrity are critical. The insert’s PVD layer improves wear resistance on interrupted cuts and variable cutting conditions, while the double-sided design provides two usable edges for cost-effective tool life. When paired with an appropriate chipbreaker and a matching holder, the system reduces secondary operations and contributes to a consistent surface finish on shafts and bores during both external and internal turning tasks. System compatibility and economical handling The SNMG format is ISO-standardised; compatibility with a toolholder is determined by form, clearance angle, tolerance class, fastening, size and thickness. The square plate with a cylindrical hole and a plate thickness of 4.76 mm integrates into common external holders and boring bars designed for SNMG inserts. The double-sided nature makes tool management straightforward: inserts can be rotated to a fresh edge, lowering per-part tooling costs and simplifying inventory for batch production. Practical selection and setup guidance Choosing the right chipbreaker and grade is essential: select a chipbreaker suited to the feed and depth of cut, and confirm that the holder supports the 90° cutting angle for the intended operation. The insert’s dimensions (size 12) and 0° clearance specification ensure predictable engagement with the workpiece. For shops that require support with cutting parameters or holder pairing, the technical consultants at Metav Werkzeuge can provide manufacturer-recommended speeds, feeds and approach strategies that match machine rigidity and part tolerances. For application-specific cutting data, batch pricing or to confirm holder compatibility for the AH6225 grade, contact Metav Werkzeuge at info@metav-werkzeuge.com or call +49 2822 7131930 — technical consultants are available to advise on integration into existing tool systems. Technical data Article number: 6947309 Manufacturer item number: 6947309 SKU: 6947309-Tungaloy Manufacturer SKU: TUN6947309 Item name: SNMG120408 AH6225 Tungaloy indexable insert Facts Geometry angle: 90° Corner radius: 0.8 mm Plate thickness: 4.76 mm Size designation: 12 Clearance angle: 0° Plate form: square Special features PVD-coated carbide (AH6225) Double-sided insert with cylindrical hole ISO turning insert, model series: ISO-Drehwendeschneidplatten Optimised for stainless steel machining Compatibility depends on holder form, clearance angle, tolerance class, fastening, size and thickness FAQ What materials is this insert suitable for? The SNMG 120408 AH6225 insert is optimised for stainless steel and performs well under medium-duty turning conditions; the AH6225 grade provides a balance between wear resistance and edge sharpness. How many usable edges does the insert offer? The insert is double-sided, providing two usable cutting edges per side, which extends the effective tool life and improves cost efficiency for batch machining. What are the key dimensions to check for holder compatibility? Check the plate size (12), plate thickness (4.76 mm), corner radius (0.8 mm) and the cylindrical hole form to ensure correct seating and clamping in the intended SNMG holder. Does the PVD coating affect cutting parameters? Yes; the PVD layer on the AH6225 grade increases wear resistance and often allows stable performance at slightly higher speeds compared with uncoated grades, but recommended speeds and feeds should be adapted to machine rigidity and part tolerances. Is this insert suitable for both external and internal turning? Yes, the ISO SNMG 120408 format and its 90° geometry make it appropriate for both external and internal turning operations when used with a compatible holder. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
SNMG 120408 AH6225 Wendeplatten - Tungaloy
Benefit from the SNMG120408 AH6225’s combination of PVD-coated carbide, a 0.8 mm corner radius and a square geometry for stable edge life and consistent performance in stainless steel turning; order via Metav Werkzeuge or request application advice from our consultants. SNMG120408 AH6225 Tungaloy indexable turning insert — PVD-coated carbide, 0.8 mm corner radius The SNMG120408 AH6225 is a square ISO indexable turning insert engineered for external and internal turning of stainless steels, offering a sharp yet stable cutting edge for medium machining and variable conditions. PVD-coated carbide for improved wear resistance Optimised for stainless steel turning 0.8 mm corner radius for robust edge life Square geometry with cylindrical hole and 4.76 mm thickness Reliable, repeatable cutting performance for stainless steels The insert’s PVD-coated carbide composition and the AH6225 grade deliver a balance between edge sharpness and toughness, aimed at rostfreie Stahl / stainless steel machining under changing conditions. The advanced coating reduces adhesion and improves resistance to built-up edge, which is particularly important when working with stainless materials that tend to work-harden. Featuring a double-sided chipbreaker, the geometry promotes stable chip formation and reduces vibration, resulting in more consistent surface finish and reduced tool changes. In practical terms, this means fewer stoppages and more predictable component quality during batch production. Seamless integration into ISO turning systems for secure clamping Compatibility with the toolholder is defined by geometry, clearance angle (0°), tolerance class, fastening method, size and thickness. The square SNMG geometry with a cylindrical hole enables positive clamping in standard ISO external holders or boring bars, while the 90° included angle suits facing and general turning operations. The insert is part of a system consisting of the ISO indexable plate, the appropriate external holder or boring bar, a shim/clamping set and replacement screws — a complete setup that simplifies inventory and reduces setup time. Clear specification of the plate thickness (4.76 mm) and plate size (12 mm) aids correct holder selection, avoiding indexing errors and maintaining cutting stability. Durability, edge management and application guidance The 0.8 mm corner radius offers a compromise between load-bearing capacity and surface finish: it increases notch resistance and extends edge life compared with finer radii while maintaining acceptable cutting forces for medium cuts. For finishing passes at lighter feeds, a smaller radius would be preferred, whereas the 0.8 mm radius is well suited to semi-finishing and general turning stages. The universal AH6225 grade is designed for mid-range parameters; selecting the appropriate chipbreaker and cutting data according to component rigidity and material condition ensures optimal results. Handling and indexing are straightforward thanks to the insert’s square form and symmetric chipbreaker: both sides can be used, doubling the effective tool life before disposal. Contact Metav Werkzeuge for tailored application advice on Tungaloy turning inserts and guidance on feed and speed parameters; reach us at info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: 6796313 Manufacturer SKU: TUN6796313 Product name: SNMG120408 AH6225 Tungaloy-Wendeplatte Numbers / Core technical data Corner radius: 0.8 mm Plate thickness: 4.76 mm Plate size: 12 mm Included angle: 90° Clearance angle: 0° Designs / Special features Material: carbide Coating: PVD-coated carbide Geometry: square plate Hole: with cylindrical hole Chipbreaker: double-sided Model series: ISO turning indexable inserts Application: turning (external and internal) FAQ What materials is this insert best suited for? The SNMG120408 AH6225 is formulated as a universal grade for stainless steel machining and performs reliably across a range of ferritic and austenitic stainless alloys. How does the 0.8 mm corner radius affect machining? A 0.8 mm corner radius increases edge strength and resistance to notch wear, making the insert suitable for semi-finishing and general turning where a balance between finish and durability is required. Is the insert reversible or single-use per edge? The square geometry with a double-sided chipbreaker allows multiple indexings; the insert can be rotated to present fresh cutting edges until all usable sides are consumed. What are the benefits of the PVD coating on this grade? The PVD-coated carbide reduces adhesion and increases wear resistance, which helps to maintain edge integrity and minimise built-up edge when machining stainless steels. Which holders are compatible with this insert? Compatibility depends on form, clearance angle, tolerance class, fastening and size; the SNMG120408 fits standard ISO external holders and boring bars designed for SNMG plates. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
SNMG 120408 AH6225 Wendeplatten - Tungaloy
Take advantage of a hard-wearing, PVD-coated carbide grade that balances a sharp cutting edge with stable performance for medium turning tasks; the SNMG form and 0.8 mm corner radius provide reliable chip control and repeatable results in rostfreier Stahl operations. Order the insert directly via Metav Werkzeuge or consult our specialists for holder compatibility and setup. SNMG 120408 AH6225 — Tungaloy turning insert for Turning SNMG120408 AH6225 is an ISO-conforming indexable insert designed for external and internal turning, optimised for rostfreier Stahl and variable machining conditions PVD-coated carbide AH6225 for rostfreier Stahl Stable, sharp cutting edge for medium machining Double-sided chipbreaker for consistent chips Square SNMG form with 0.8 mm corner radius Boosted wear resistance and consistent edge performance The PVD-coated AH6225 grade combines a wear-resistant top layer with a finely prepared carbide substrate (Hartmetall) to deliver a balance between edge sharpness and toughness. This composition improves resistance to built-up edge and abrasion when machining rostfreier Stahl, which often work-hardens and challenges tool life. The result is a reduction in unplanned tool changes and more predictable process windows — valuable for batch production and mixed-series turning where stability is essential. Reliable chip control and improved surface quality Equipped with a double-sided chipbreaker, the insert secures controllable swarf formation across a range of depths of cut, helping to prevent long, stringy chips that impair cycle time and surface integrity. Better chip control contributes directly to a more consistent surface finish and fewer interruptions for chip removal. In applications that require repeatable part geometry, this behaviour supports higher first-pass acceptance rates and steadier downstream processing. ISO SNMG form for straightforward mechanical compatibility The insert follows ISO SNMG120408 geometry, a square plate with a cylindrical hole and a nominal included angle of 90°, ensuring standardised mounting on compatible external holders and boring bars. Compatibility depends on form, relief angle, tolerance class, attachment method, size and thickness; matching those parameters avoids clamping issues and ensures correct seat contact. The listed 0° relief angle and plate thickness 4.76 mm are key dimensions that determine which holders and clamp sets are suitable. Economical operation through indexability and edge geometry Being indexable and double-sided, the component allows multiple cutting edges per insert, lowering per-edge cost and simplifying inventory management. The 0.8 mm corner radius provides a compromise between edge strength and finish: large enough to resist thermal and mechanical chipping, yet small enough to achieve acceptable part finish in medium-turning operations. Such a trade-off supports productive machining strategies where both robustness and surface quality matter. Practical selection notes for stable machining For best results in external or internal turning of rostfreier Stahl, select a holder that matches the SNMG seat and secures the insert without overhang; ensure clamp sets and spare screws correspond to the ISO geometry. Choose a chipbreaker and grade aligned with the workpiece stability and cutting conditions — the AH6225 grade is intended as a universal solution for changing conditions and moderate cutting parameters. For tailored recommendations on feeds, speeds and clamping, consult technical advisors to match the insert to machine rigidity and operation scope. Contact Metav Werkzeuge today for application advice on the Tungaloy SNMG120408 AH6225 turning insert — email info@metav-werkzeuge.com or call +49 2822 7131930 for fast, practical support Technical data Article number: 6947319 SKU: 6947319-Tungaloy Manufacturer SKU: TUN6947319 Material: Hartmetall Model series: ISO-Drehwendeschneidplatten Facts Size (flat-to-flat): 12 mm Thickness: 4.76 mm Corner radius: 0.8 mm Included angle: 90° Relief angle: 0° Special features ISO SNMG120408 form PVD-coated grade AH6225 Double-sided chipbreaker Square plate with cylindrical hole Suitable for rostfreier Stahl FAQ What materials is this insert intended for? The AH6225 PVD-coated grade is specified for machining rostfreier Stahl and offers a good balance of wear resistance and edge sharpness for medium turning operations. How is compatibility with a toolholder determined? Compatibility depends on form, relief angle, tolerance class, attachment method, size and thickness; the SNMG120408 geometry and 4.76 mm thickness must match the holder seat and clamp system. Does the chipbreaker suit both external and internal turning? Yes, the insert’s double-sided chipbreaker is designed for controlled chip formation in both external and internal turning, aiding consistent process behaviour. What benefit does the 0.8 mm corner radius provide? A 0.8 mm corner radius increases edge robustness against chipping while still allowing acceptable surface finish in medium machining, supporting longer uninterrupted runs. Is AH6225 a universal grade for variable conditions? The AH6225 grade is formulated as a universal solution for changing conditions when machining rostfreier Stahl, combining durability with a stable cutting edge for varied applications. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
SNMG 120408 AH6225 Wendeplatten - Tungaloy
Take advantage of a PVD-coated carbide grade AH6225 that balances a sharp cutting edge with stability and wear resistance, combined with a 0.8 mm corner radius and double-sided chipbreaker for economical, versatile turning of stainless steels; order or request advice via Metav Werkzeuge for immediate technical support. SNMG120408 AH6225 — indexable turning insert for turning by Tungaloy The SNMG120408 AH6225 is an ISO-standard indexable turning insert designed for medium turning operations, offering a sharp, stable cutting edge optimised for stainless steels. PVD-coated carbide grade AH6225 0.8 mm corner radius for precision Double-sided chipbreaker for versatility ISO SNMG120408 square insert, 90° geometry Consistent chip control and reliable edge life for stainless steels The PVD-coated carbide grade AH6225 provides a balanced combination of edge sharpness and robustness, making it suitable for variable conditions during medium turning. The double-sided chipbreaker reduces chip length and supports stable evacuation, which improves process reliability and reduces rework. Because the substrate and coating are engineered for stainless steels, the insert maintains consistent flank wear and avoids rapid built-up edge, resulting in longer productive tool life and fewer index changes. Precision geometry that supports repeatable results A 0.8 mm corner radius and 90° insert geometry deliver a predictable profile for external and internal turning. The modest corner radius improves edge strength while still permitting a good surface finish in standard feeds; this is an advantage in mixed-batch production where repeatability matters. The square plate form and 0° clearance angle require matching holders that respect form, tolerance class and clamping arrangements to ensure concentricity and vibration-free machining. System approach: compatibility and simple assembly save set-up time The insert functions as part of an ISO-compliant system: the indexable plate, a compatible external holder or boring bar, a locating shim and clamping kit, plus replacement screws. Compatibility depends on plate shape, thickness and mounting style — this insert is a square SNMG with a cylindrical hole and a plate thickness of 4.76 mm. Correct selection of the clamping set and tolerance class minimises runout and maximises tool life, reducing downtime and increasing overall shop throughput. Economical use through reversible indexing and versatility Being double-sided and ISO-standard, the insert offers a cost-effective option: two usable edges per side increase edge count per plate and reduce tooling costs per component. The PVD coating helps maintain a sharp edge under varying cutting conditions, while the underlying carbide substrate supports moderate cutting speeds typical for stainless steel turning. For workshops seeking a practical, general-purpose solution, this indexable plate provides predictable productivity without frequent tool changes. For tailored advice on using genuine Tungaloy SNMG120408 AH6225 inserts in production, or to secure immediate delivery through Metav Werkzeuge, contact Metav Werkzeuge at info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: 6826344-Tungaloy (SKU) Manufacturer article number: 6826344 Manufacturer SKU: TUN6826344 Model series: ISO-Drehwendeschneidplatten Application: Turning Facts Plate designation: SNMG120408 Plate size: 12 Plate thickness: 4.76 mm Corner radius: 0.8 mm Approach angle: 90° Clearance angle: 0° Special features Material: carbide Coating: PVD-coated grade AH6225 Plate form: square Hole: with hole, cylindrical hole Chipbreaker: double-sided Typical use: external and internal turning; select chipbreaker and grade for material and stability FAQ What materials is this insert primarily intended for? The SNMG120408 AH6225 insert is primarily designed for stainless steels; the PVD-coated carbide grade AH6225 balances sharpness and edge stability for these materials. How does the 0.8 mm corner radius affect performance? A 0.8 mm corner radius offers improved edge strength compared with smaller radii while still allowing good surface finish at typical turning feeds when using the SNMG120408 geometry. Is the insert reversible and how many cutting edges are available? The SNMG120408 is double-sided with a reversible design, providing multiple usable edges per plate and improving cost efficiency in batch production. What holder considerations are necessary for correct use? Compatibility requires a holder that matches the SNMG form, tolerance class, size and thickness; correct clamping and the use of a suitable locating shim ensure low runout and stable performance. Can this insert be used for internal as well as external turning? Yes, the indexable geometry and chipbreaker make the plate suitable for both external and internal turning applications when paired with the appropriate holder or boring bar. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
SNMG 120408 AH6225 Wendeplatten - Tungaloy
Take advantage of a sharp, stable cutting edge and PVD coating for reliable stainless-steel turning; order directly via Metav Werkzeuge or consult the specialists for holder compatibility and optimal grade selection. SNMG120408 AH6225 indexable turning insert for turning — Tungaloy SNMG120408 AH6225 is a PVD-coated carbide indexable insert engineered for efficient external and internal turning, offering a sharp yet durable cutting edge for variable machining conditions. ISO-standard SNMG geometry, 90° shape PVD-coated carbide grade AH6225 Optimised for stainless steels Double-sided chipbreaker, central cylindrical hole Consistent, sharp cutting performance for stainless steels The SNMG120408 AH6225 insert combines a PVD-coated carbide grade with a finely balanced edge geometry to deliver stable cutting in stainless-steel applications. The AH6225 grade is formulated to maintain a sharp cutting edge while resisting deformation under medium cutting conditions and changing parameters. PVD coating reduces adhesive wear and improves heat resistance, which results in more predictable tool life and more consistent surface finish compared with uncoated grades. This technical balance reduces downtime and supports productive turning processes. Better chip control and productivity through optimised chipbreaker design A double-sided chipbreaker with a central cylindrical hole supports secure clamping and repeatable chip formation. The integrated chip control reduces the risk of long, tangled chips and improves evacuation in both external and internal turning operations. As a consequence, cycle times can be shortened and machine uptime increases – an important economic advantage in batch production. The square insert form with a 90° shape ensures robust radial support and straightforward orientation in common ISO-compatible holders. Easy integration into ISO tooling systems for inventory simplicity As an ISO-series turning insert, compatibility with holders depends on form, clearance angle, tolerance class, fixation, size and thickness. The standardised SNMG geometry and the documented dimensions simplify holder selection and spare-part management. Specifying the corner radius 0.8 mm and thickness 4.76 mm in procurement makes it easier to match existing toolholders and reduces the need for ad hoc adaptations. This clarity supports streamlined logistics and repeatable mounting procedures on the shop floor. Practical guidance for application and machining strategies Designed for turning operations, this insert performs well in both external and internal cuts when the correct chipbreaker and cutting parameters are chosen. For rostfreie Stähle, moderate cutting speeds with stable feeds and adequate coolant can exploit the combination of AH6225 toughness and the PVD layer to avoid built-up edge. Selecting the appropriate chipbreaker variant for the workpiece material and rigidity of the setup will help achieve the desired surface quality with minimal rework. Where intermittent cuts or variable feed conditions occur, the insert’s stable edge geometry offers reliable performance. Material and maintenance considerations that save production time Made from high-quality carbide and supplied as a double-sided insert, this indexable tool reduces tooling costs per edge while maintaining repeatable geometry across re-grips. The cylindrical central hole supports secure seating and repeatable clamping torque, lowering the risk of orientation errors and runout. Regular inspection of the cutting edge and adherence to recommended cutting parameters will extend edge life and protect component tolerances, contributing to predictable production output. Contact Metav Werkzeuge for tailored advice on SNMG120408 AH6225 inserts, holder compatibility and batch supply—email info@metav-werkzeuge.com or call +49 2822 7131930 to discuss the right grade and chipbreaker for the application Technical data Article number: 6826087 Manufacturer SKU: TUN6826087 SKU: 6826087-Tungaloy Designation: SNMG120408 AH6225 Facts Insert size: 12 mm Thickness: 4.76 mm Corner radius: 0.8 mm Clearance angle: 0° Shape angle: 90° Double-sided cutting edges Special features Material: Carbide Coating / Grade: AH6225 (PVD) Hole style: Cylindrical hole Chipbreaker: Double-sided Application: External and internal turning Series: ISO turning indexable inserts Compatibility: Determined by form, clearance, tolerance class, fixation, size and thickness FAQ What materials is this insert suitable for? The SNMG120408 AH6225 insert is optimised for stainless steels; the AH6225 PVD-coated carbide grade offers improved heat resistance and edge stability for rostfreie Stähle in turning operations. How does the double-sided chipbreaker help in production? The double-sided chipbreaker on this Tungaloy turning insert promotes consistent chip formation and evacuation, reducing interruptions and improving cycle times in both external and internal turning. Which dimensions should be checked when selecting a holder? Check insert size (12 mm), thickness (4.76 mm), corner radius (0.8 mm), clearance angle (0°) and the SNMG geometry to ensure correct fit and clamp compatibility with the chosen holder. Can the insert be used for finishing as well as roughing? With the appropriate cutting parameters and the right chipbreaker choice, the PVD-coated AH6225 grade can be used for medium finishing operations where edge stability and surface quality are required. How many cutting edges are available per insert? This SNMG-format insert is double-sided, providing multiple usable edges per insert and an economical tooling solution for turning tasks. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
SNMG 120408 AH6225 Wendeplatten - Tungaloy
Take advantage of a universally applicable carbide grade and a geometry engineered for stable cutting: the combination of PVD-coated AH6225 carbide and a 0° clearance geometry ensures reliable edge stability and consistent chip formation during mid-range turning of rostfreier Stahl. Order the SNMG120408 AH6225 turning insert directly via Metav Werkzeuge or consult our technical advisors for application-specific recommendations. SNMG120408 AH6225 Turning Insert (ISO SNMG120408) – Tungaloy A SNMG120408 AH6225 indexable turning insert designed for external and internal turning applications, offering a sharp yet robust cutting edge optimised for rostfreier Stahl. PVD-coated AH6225 for rostfreier Stahl 0° clearance for stable cutting Double-sided chipbreaker for predictable chips ISO SNMG120408, square insert with 90° nose Reliable mid-range performance for rostfreier Stahl machining The insert’s PVD-coated carbide matrix (grade AH6225) is developed as a universal solution for machining rostfreier Stahl, combining a sharp cutting edge with enhanced wear resistance. This balance reduces the frequency of index changes and supports consistent component quality in batch production. By using a coated grade optimised for variable conditions, process windows widen: feed and cut variations are better tolerated, which increases net productive time and lowers downtime for tool changes. The material choice and coating technology together provide improved thermal stability and edge life during common turning operations. Geometry and chip control that stabilise the machining process A geometry configured with 0° clearance and a 90° wedge angle provides secure engagement and predictable cutting forces, while the corner radius 0.8 mm gives a compromise between edge strength and surface finish. The double-sided chipbreaker promotes consistent chip formation across a range of feeds, aiding evacuation and reducing the risk of built-up edge on rostfreier Stahl. The square plate form with a cylindrical hole ensures accurate seating in compatible holders and simplifies indexing procedures, which contributes to repeatable clamping and process security in turning centres and lathes. System integration, handling and shop-floor benefits As an ISO-designated insert, ISO SNMG120408 integrates into standard holders and boring bars when form, clearance, tolerance class, fastening and plate thickness match. The insert is part of a system that typically includes the appropriate external holder or boring bar, a backing/clamping set and replacement screws, enabling straightforward maintenance and stock management. For production planners, the insert’s universal grade reduces the need for multiple dedicated grades, simplifying inventory while maintaining surface quality and tool life. If application parameters are unclear, technical consultation is recommended to select the optimal chipbreaker and cutting data for the specific setup. Contact Metav Werkzeuge for tailored advice on integrating the SNMG120408 AH6225 insert into existing tool systems and for ordering information via Metav Werkzeuge (info@metav-werkzeuge.com / +49 2822 7131930) Technical data Article number: 6947300 Manufacturer SKU: TUN6947300 Seller SKU: 6947300-Tungaloy Material: Carbide Numbers / Core technical data Size: 12 mm Thickness: 4.76 mm Corner radius: 0.8 mm Cutting angle: 90° Clearance angle: 0° Special features / Versions ISO designation: SNMG120408 Grade/coating: AH6225, PVD-coated Chipbreaker: Double-sided chipbreaker Plate form: Square Hole style: Cylindrical hole, with hole Typical application: Turning (external and internal) Compatibility note: Fits holders matching form, tolerance, fastening and thickness System components: Insert, suitable external holder or boring bar, backing/clamping set, replacement screws FAQ Is this insert suitable for machining rostfreier Stahl? The SNMG120408 AH6225 insert is a universal PVD-coated grade specifically developed for rostfreier Stahl and provides a balanced combination of sharpness and edge stability for mid-range turning. Which holders accept this SNMG insert? Compatibility is determined by the insert form, clearance angle, tolerance class, fastening method, size and thickness; the ISO SNMG120408 fits standard SNMG external holders and boring bars designed for 12 mm square plates. What chip control can be expected in practice? The double-sided chipbreaker delivers predictable chip formation and improved evacuation, contributing to stable cutting and reduced risk of built-up edge when machining rostfreier Stahl. Can the insert be indexed for fresh edges? Yes, the square, double-sided design allows indexing to fresh cutting edges; the system concept includes backing/clamping sets and replacement screws to facilitate safe re‑seating and reliable clamping. What are the item references for ordering? The article number is 6947300; the seller SKU is 6947300-Tungaloy and the manufacturer SKU is TUN6947300; reference these when enquiring or ordering. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
SNMG 120408 AH6225 Wendeplatten - Tungaloy
Combine the PVD-coated AH6225 grade with the ISO SNMG120408 format to achieve stable cutting performance on rostfreie Stähle; the 0.8 mm corner radius and double-sided chipbreaker deliver consistent edge life and predictable surface finish. Order the SNMG120408 AH6225 Tungaloy indexable insert directly via Metav Werkzeuge or consult their specialists for application guidance and fast supply. SNMG120408 AH6225 square ISO turning insert, PVD-coated carbide — Tungaloy The SNMG120408 AH6225 is an ISO-standard square indexable insert for external and internal turning, developed for medium-duty operations and optimised for machining rostfreie Stähle. ISO SNMG120408 square 90° insert AH6225 PVD-coated carbide grade 0.8 mm corner radius for robust edges Double-sided chipbreaker with cylindrical hole Reliable performance for medium-duty turning The SNMG120408 AH6225 indexable insert combines a PVD-coated carbide substrate with a geometry tuned for steady cutting in mixed conditions. The housing of the insert is square (90°), which provides predictable support under radial loads, while the 0.8 mm corner radius smooths engagement and reduces notch formation at interrupted cuts. As a result, tool life stabilisation is achieved through a balance of sharpness and edge strength, bringing repeatable component quality for general turning tasks. Compatibility and clamping: fit, form and secure fastening Compatibility with toolholders is determined by insert form, relief angle, tolerance class, attachment method, size and thickness; the SNMG120408 features a cylindrical hole that enables positive clamping in a wide range of ISO external holders and boring bars. The plate is double-sided, permitting rotation to a fresh edge and reducing downtime for indexable operations. Documentation and correct seat geometry ensure secure fixation and repeatable positioning for batch production. Material grade benefits and machining scope The AH6225 grade is a PVD-coated hardmetal designed as a universal solution for rostfreie Stähle, providing a sharp yet stable cutting edge under medium machining parameters. The coating supports heat resistance and wear control, which helps maintain surface finish and dimensional stability across varying feeds. Selecting a matching chipbreaker and grade to the work material, machining style and setup rigidity will optimise productivity and reduce the frequency of insert changes. Contact Metav Werkzeuge for availability, tailored cutting data and fast supply of the Tungaloy AH6225 inserts at info@metav-werkzeuge.com or by phone on +49 2822 7131930. Technical Data Article number: 6947282 SKU: 6947282-Tungaloy Manufacturer SKU: TUN6947282 Model series: ISO-Drehwendeschneidplatten Product designation: SNMG120408 AH6225 Tungaloy insert Material: Hartmetall Facts Size (edge length): 12 mm Corner radius: 0.8 mm Thickness: 4.76 mm Relief angle: 0° Insert angle: 90° ISO code: 120408 Special features PVD-coated carbide grade AH6225 Double-sided chipbreaker Cylindrical hole for secure clamping Square plate form Suitable for Drehen (turning) Designed for rostfreie Stähle Compatibility by form, relief angle, tolerance class, attachment, size and thickness FAQ What materials is this insert suitable for? The SNMG120408 AH6225 indexable insert is optimised for rostfreie Stähle; the AH6225 PVD-coated hardmetal offers a balance of edge sharpness and wear resistance for medium turning tasks. How is the insert fixed in the holder? This SNMG120408 version has a cylindrical hole enabling positive fastening; correct clamping depends on matching the holder geometry to the insert form, relief angle, tolerance class, size and thickness. Can both cutting edges be used? Yes, the insert is double-sided and indexable so both edges can be rotated into service, extending usable life and reducing changeover frequency. What is the corner radius and typical application? The corner radius is 0.8 mm, suitable for general external and internal turning where a compromise between edge strength and finish is required; the square 90° form supports radial loads well. Which chipbreaker is supplied and why does it matter? A double-sided chipbreaker is specified for the SNMG120408 to assist chip control across varying feeds and depths; choosing the right breaker supports secure evacuation and consistent surface quality. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
SNMG 120408 AH6225 Wendeplatten - Tungaloy
Benefit from a PVD-coated carbide grade engineered for reliable mid-range turning, consistent chip control and a 0.8 mm corner radius that supports stable edge life under varying conditions. Order the SNMG120408 AH6225 insert directly via Metav Werkzeuge or ask our consultants if needed. SNMG 120408 AH6225 — Indexable turning insert, PVD-coated carbide, 90° (Tungaloy) A compact SNMG 120408 AH6225 indexable insert designed for robust external and internal turning, optimised for rostfreier Stahl and varying machining conditions. PVD-coated carbide for rostfreier Stahl Sharp yet stable cutting edge Double-sided, square 90° geometry Cylindrical hole for secure clamping Consistent mid-range turning performance for rostfreier Stahl The PVD-coated carbide grade AH6225 combines a sharp cutting edge with structural toughness, delivering dependable results during medium cutting operations. The PVD-coated surface increases wear resistance while maintaining edge sharpness, which translates into fewer interruptions for tool changes and more predictable cycle times. For applications on rostfreier Stahl, this balance reduces chatter and supports uniform surface finish with stable tool life under fluctuating feeds and speeds. Compatibility and secure clamping to maintain production uptime Produced to ISO indexing dimensions, the square insert with a cylindrical hole and 90° geometry enables secure attachment in standard holders. Compatibility with a given holder depends on the insert’s form, relief angle, tolerance class, fastening method, size and thickness; matching these parameters ensures correct seating and repeatable accuracy. The double-sided layout allows indexing to fresh edges, improving economy per cutting edge and contributing to uninterrupted production. Practical guidance for selection and application The 0.8 mm corner radius provides a compromise between cutting strength and dimensional control, suitable for medium-depth turning and finishing passes where stability varies. With a plate thickness of 4.76 mm, the insert offers stiffness for conventional operations while remaining compatible with common ISO toolholders. Choose the doppelseitig chipbreaker style and AH6225 grade when machining rostfreier Stahl, and prefer a rigid setup for best surface quality and extended edge life. Contact Metav Werkzeuge for tailored selection of original Tungaloy SNMG120408 AH6225 inserts; our technical team is available at info@metav-werkzeuge.com or +49 2822 7131930 to advise on holder compatibility and process optimisation Technical Data Article number: 6826349 Manufacturer SKU: TUN6826349 Supplier SKU: 6826349-Tungaloy Designation: SNMG120408 AH6225 Model series: ISO turning indexable inserts Facts Inscribed circle / size: 12 mm Thickness: 4.76 mm Corner radius: 0.8 mm Relief angle: 0° Cutting angle: 90° Hole: cylindrical Sides: double-sided Special features Material: carbide Coating / grade: AH6225 (PVD-coated) Application: turning (external and internal) Shape: square Chipbreaker: double-sided Compatibility determined by form, relief angle, tolerance class, fastening, size and thickness Designed for medium machining and varying conditions Suitable for rostfreier Stahl FAQ Which materials is this insert best suited for? The SNMG120408 AH6225 insert is optimised as a universal grade for rostfreier Stahl, offering a balance of sharpness and edge stability for stainless applications. How is the insert secured in the holder? The insert uses a cylindrical hole and ISO indexing form; secure clamping depends on matching the insert’s form, relief angle, tolerance class, fastening method, size and thickness to the chosen holder. What are the advantages of the AH6225 grade? AH6225 is a PVD-coated carbide grade designed to provide a sharp yet resilient cutting edge for medium cutting, improving wear resistance and chip formation control in changing conditions. When is the 0.8 mm corner radius appropriate? A 0.8 mm corner radius suits medium stock-removal and turning operations where a compromise between edge strength and dimensional accuracy is required. Is the SNMG120408 indexable and economical to use? Yes; the square, double-sided insert can be indexed to expose fresh edges, which increases usable edge count and reduces tooling cost per component. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
SNMG 120408 AH6225 Wendeplatten - Tungaloy
The combination of a sharp, PVD‑coated AH6225 grade and ISO‑compliant geometry delivers stable cutting performance and predictable tool life for medium turning of stainless steels; order directly via Metav Werkzeuge or consult the technical team for process optimisation. SNMG 120408 AH6225 Tungaloy indexable insert for turning — PVD‑coated carbide, 90° SNMG120408 AH6225 is an ISO‑specified indexable turning insert designed for medium finishing of stainless steels and adaptable to standard external and internal turning applications. SNMG120408 geometry, ISO-compatible PVD-coated carbide grade AH6225 0.8 mm corner radius for consistent edge Double-sided chipbreaker with cylindrical hole Consistent cutting performance for stainless steels The SNMG120408 AH6225 insert is specified for medium machining where a balance of sharpness and edge stability is required. The PVD coating on the carbide substrate reduces adhesion and wear when machining stainless steels, helping to lower the risk of built‑up edge and stabilise cutting forces. This results in a predictable tool life and more consistent part geometry over extended production runs, which supports higher first‑pass yield and fewer tool changes. Compatibility and secure mounting for production use ISO compatibility means the geometry and mounting dimensions are standardised; compatibility to a holder is determined by form, clearance angle, tolerance class, fastening method, size and thickness. The insert is supplied in a square form with a cylindrical hole and a 90° insert angle, making it suitable for common external holders and boring bars. The 12 mm seat and 4.76 mm thickness give robust support in the pocket, and the double‑sided design halves the effective tooling cost per edge compared with single‑edged solutions. Practical application advice to improve cycle times For reliable chip control and surface integrity, pair the AH6225 grade with the appropriate chipbreaker style and machining parameters: the double‑sided breaker is suited to variable conditions and mixed stability operations. External and internal turning operations benefit from a 0.8 mm corner radius where improved edge strength is needed without compromising surface finish. Where chatter or low rigidity is present, opt for lower feeds and ensure holder overhang is minimised to keep cutting forces stable. Productivity, economics and surface quality Selecting the right combination of insert grade and geometry delivers measurable cost benefits: stable chip formation and fewer interruptions translate into increased machine uptime and improved surface finish, while the PVD layer contributes to consistent edge retention. The insert’s specification supports productive machining with lower tooling consumption per part, making it a cost‑effective choice for batch production and mixed‑batch environments where repeatability and process safety are priorities. Discuss your application with Metav Werkzeuge to confirm suitability and secure prompt supply; our technical advisors are available to recommend optimal holder pairings and cutting data for the Tungaloy SNMG120408 AH6225 insert — contact Metav Werkzeuge at info@metav-werkzeuge.com or +49 2822 7131930 Technical data Article number: 6826081 SKU: 6826081-Tungaloy Manufacturer SKU: TUN6826081 Model series: ISO-Drehwendeschneidplatten Material: Hartmetall Facts ISO designation: SNMG120408 Size: 12 mm Thickness: 4.76 mm Corner radius: 0.8 mm Clearance angle: 0° Insert angle: 90° Hole: cylindrical Special features Coating: PVD Grade: AH6225 Chipbreaker: double-sided Application: Turning; suited to stainless steels Geometry: square, hole-mounted FAQ What operations is this insert intended for? The SNMG120408 AH6225 insert is intended primarily for external and internal turning, optimised for medium finishing operations and process conditions encountered when machining stainless steels. How is holder compatibility determined? Compatibility with a holder is determined by insert form, clearance angle, tolerance class, fastening method, size and thickness; the SNMG120408 follows ISO dimensions to fit standard turning holders. What advantages does the AH6225 grade offer? The AH6225 grade is a universal PVD‑coated carbide designed for a sharp yet stable cutting edge on stainless steels, providing good wear resistance and reliable chip formation under variable conditions. Is the insert double‑sided and does it save cost? Yes, the insert is double‑sided with a cylindrical hole, which provides two cutting edges and improves cost efficiency per edge compared with single‑edged inserts. Which corner radius suits general finishing? The 0.8 mm corner radius offers a compromise between edge strength and surface integrity, suitable for medium finishing where a robust edge is required without excessive tool pressure. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
Fragen zu diesen Produkten??
Mit mehr als 30 Jahren Erfahrung beraten wir Sie gerne persönlich.
Tel.: +49 2822 7131930
Mail: info@metav-werkzeuge.com