SNMN 120420 FX105 Wendeplatten - Tungaloy
Take advantage of a robust carbide construction and the FX105 grade to secure stable cutting performance and extended edge life in milling operations; the square 90° geometry with a 2 mm corner radius supports predictable tool behaviour. Order directly via Metav Werkzeuge or consult their specialists for application-specific guidance. SNMN 120420 FX105 SNMN milling indexable insert – 90° square, 2 mm corner radius | Tungaloy The SNMN120420 FX105 is a square, 90° carbide insert designed for use in Tungaloy milling systems, offering a balance of wear resistance and edge stability for face, shoulder, slot, high-feed and contour milling. SNMN120420 geometry for Tungaloy milling systems FX105 grade for wear resistance and edge stability 90° square form with 2 mm corner radius Carbide construction for reliable cutting performance Consistent geometry and secure system compatibility for efficient milling The square indexable insert is designed so that the insert seat and geometry match the corresponding milling body, ensuring stable clamping and repeatable positioning. The defined 90° angle and precise seating reduce chatter and improve dimensional control, which in turn lowers scrap rates and rework. For machining centres and production lines that demand repeatable results, this compatibility supports shorter setup times and predictable throughput. Robust grade and edge stability for longer tool life under load The FX105 carbide grade combines wear resistance with adequate toughness to maintain a sharp cutting edge during interrupted and continuous cuts. The 2 mm corner radius increases edge strength in heavier passes while preserving acceptable surface finish for many mating operations. This balance reduces the frequency of index changes and delivers an improved cost-per-component ratio in medium-duty milling workloads. Application guidance and integration into milling tool systems Intended specifically for milling, the insert is suited to face, shoulder, groove, high-feed and contour operations depending on the chosen milling body and geometry. The insert is supplied without a central hole and without a chipbreaker, so the selected milling body and clamp method must accommodate a secure seat and the required chip evacuation strategy. Correct matching of insert, clamp screw and milling body ensures reliable chip formation and stable cutting conditions. For precise milling results with the SNMN120420 FX105 insert from Tungaloy, contact Metav Werkzeuge for tailored application advice or to request a quotation via info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: 6806975 Manufacturer SKU: TUN6806975 SKU: 6806975-Tungaloy Model series: Milling indexable inserts Designation: SNMN120420 FX105 Facts Shape: square Size: 12 mm Thickness: 4.76 mm Corner radius: 2 mm Relief angle: 0° Insert angle: 90° Hole: none Chipbreaker: none Special features Material: carbide Grade: FX105 Intended use: milling Compatible with Tungaloy milling systems Typical applications: face, shoulder, slot, high-feed, contour milling System components: insert, milling body, clamp screw, optional shim FAQ What applications suit this insert best? The SNMN120420 FX105 insert is designed for milling tasks such as face milling, shoulder milling, slotting, high-feed and contour operations when paired with the appropriate Tungaloy milling body. How does the FX105 grade affect tool life? FX105 provides a combination of wear resistance and toughness that helps maintain edge stability under typical milling loads, resulting in fewer index changes and improved component output per insert. Is a hole or chipbreaker required for mounting? This version is supplied without a central hole and without a chipbreaker; mounting depends on the milling body's clamping concept and the chosen chip evacuation strategy for the machining task. Which materials are suitable for machining with this insert? The insert is a general-purpose carbide grade intended for a broad range of milling applications; selection of cutting parameters should reflect the workpiece material and the intended machining result. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
SNMN 120424 FX105 Wendeplatten - Tungaloy
Benefit from a durable, high-performance milling solution that combines the FX105 carbide grade with a 2.4 mm corner radius and a secure 90° geometry for consistent edge stability and productive machining; order the insert directly via Metav Werkzeuge or consult our specialists for application guidance. SNMN120424 FX105 – Milling insert for Tungaloy systems, 90° geometry, 2.4 mm corner radius (Tungaloy) SNMN120424 FX105 is an indexable milling insert designed for face, shoulder, slot, high-feed and contour milling within matching Tungaloy milling systems Carbide grade FX105 for balanced wear resistance 90° geometry for robust shoulder milling 2.4 mm corner radius for edge strength Square 12 mm size, 4.76 mm plate thickness Consistent tool life through an engineered carbide grade The FX105 carbide grade is developed to deliver a balance of wear resistance and toughness, which keeps cutting edges stable across mixed machining tasks. This mix of properties reduces unexpected tool changes and contributes to predictable component quality when performing planing, shoulder or contour operations. As an indexable insert, the plate provides repeatable performance and simplifies stock management by offering consistent re-indexing behaviour. Rigid geometry for accurate and secure milling A 90° included angle and a 2.4 mm corner radius create a geometry that resists chipping and supports heavier axial engagement during shoulder and slot milling. The square 12 mm form factor and 4.76 mm plate thickness increase stiffness at the cutting edge, translating into improved dimensional accuracy and surface finish on the workpiece. The absence of a centre hole and the specified 0° clearance angle are designed for clamping stability in compatible milling bodies, ensuring the insert remains seated and accurately referenced under load. System-focused design to reduce downtime and set-up complexity This insert is part of a modular milling system and requires a matching seat, clamp screw and, if applicable, support shim on the cutter body; correct matching of the insert geometry and the milling body is essential for safe and efficient operation. The combination of a proven carbide grade and a robust plate form reduces changeover frequency and supports higher process reliability, which in turn improves throughput and lowers per-part costs. For users seeking guidance on integration or selecting the correct milling body, technical consultation is available to ensure optimal pairing and cutting data. Contact Metav Werkzeuge for tailored application advice on the Tungaloy SNMN120424 FX105 insert — technical consultants available at info@metav-werkzeuge.com or by phone on +49 2822 7131930 Technical Data Article number: 6806976 Manufacturer SKU: TUN6806976 Model series: Fräswendeschneidplatten Material: Carbide Grade: FX105 Facts Corner radius: 2.4 mm Plate size: 12 mm Plate thickness: 4.76 mm Included angle: 90° Relief angle: 0° Special features Square plate form No centre hole Intended application: milling Requires matching milling body and clamp screw Indexable insert for Tungaloy milling systems FAQ What materials is this insert suited for? This SNMN120424 FX105 insert is formulated for general milling applications; the FX105 carbide grade offers a balanced performance across a broad range of materials typically encountered in milling operations. How does the 2.4 mm corner radius affect cutting performance? The 2.4 mm corner radius increases edge strength and resistance to chipping, which helps the SNMN120424 FX105 maintain dimensional stability during shoulder and slot milling. Is a specific cutter body required for this insert? Yes, the insert must be used with a compatible Tungaloy milling body that matches the seat, geometry and clamping method to ensure correct seating and secure clamping under cutting forces. Can the insert be reindexed and how many edges are available? As an indexable milling plate, the SNMN120424 FX105 provides multiple usable cutting edges; the number of edges depends on the insert orientation and the chosen index strategy within the milling system. What benefits does the FX105 grade provide in production? The FX105 grade offers improved process stability through a combination of wear resistance and edge toughness, resulting in longer periods between regrinds and more consistent surface quality. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
SNMN 190416 FX105 Wendeplatten - Tungaloy
Take advantage of the proven combination of a robust FX105 carbide grade, precise 1.6 mm corner radius and a 90° geometry for consistent, productive turning operations. Order the insert directly via Metav Werkzeuge or consult the team for application advice. SNMN190416 FX105 – ISO indexable insert for turning | Tungaloy SNMN190416 FX105 is an ISO‑standard indexable insert designed for turning applications, offering a balanced carbide grade for wear resistance and edge stability. ISO‑standard SNMN insert design Tungaloy FX105 carbide grade 1.6 mm corner radius for stable cutting 90° geometry for versatile turning High‑performance geometry and material for reliable turning The SNMN190416 FX105 insert combines a Tungaloy carbide grade with a geometry engineered for dependable turning results. The FX105 grade provides a calculated balance of wear resistance and toughness, which translates into longer cutting life and fewer interruptions for edge changes. The 1.6 mm corner radius supports stable engagement at higher feed rates, while the 90° included angle permits versatile external and internal turning operations. With a 0° relief angle specified, the insert offers predictable chip flow and reproducible cutting forces—key factors for process stability and repeatable surface finish in production environments. Seamless integration into ISO turning systems reduces setup time Being an ISO‑dimensioned insert, integration into standard holders and boring bars is straightforward; compatibility depends on form, relief angle, tolerance class, fastening, size and thickness. The square plate format and the nominal dimensions (19 mm size, 4.76 mm thickness) make changeovers quick and precise when paired with the correct clamping set and replacement screws. This reduces machine downtime and simplifies inventory management by aligning with common holder families. For best results, match the insert with a chipbreaker and cutting parameters suited to the workpiece material and machine rigidity. Operational benefits and recommended use cases The absence of a dedicated chipbreaker on this insert highlights its role as a geometry‑focused solution: when combined with the appropriate grade and cutting data, the result is stable chip formation and consistent edge integrity. Manufacturers seeking a productive option for general turning tasks will benefit from the insert’s balanced performance—one clear advantage is fewer unplanned tool changes, which improves throughput. The system approach—insert, holder, shim/clamp and spare screws—ensures repeatable clamping and minimal variation between tool changes, supporting high process confidence on the shop floor. Contact Metav Werkzeuge today for bespoke cutting‑tool recommendations and to order Tungaloy SNMN190416 FX105 indexable inserts through Metav Werkzeuge; technical consultation is available by email or phone. Technical Data Article number: 6806979 SKU: 6806979-Tungaloy Manufacturer SKU: TUN6806979 Brand: Tungaloy Model series: ISO‑Drehwendeschneidplatten Designation: SNMN190416 Facts Corner radius: 1.6 mm Size: 19 mm Thickness: 4.76 mm Included angle: 90° Relief angle: 0° Special features Grade / coating: FX105 Material: carbide Plate form: square Hole: none Chipbreaker: none Intended application: Turning System components: compatible external holder or boring bar, shim/clamp and replacement screws FAQ What types of turning are suitable for this insert? This insert is intended for external and internal turning; the SNMN190416 FX105 by Tungaloy performs well in general turning operations when paired with an appropriate holder and cutting data. How does the FX105 grade influence tool life? The FX105 grade balances wear resistance and toughness, which increases edge stability and helps extend effective tool life under typical turning loads for indexable inserts. Which holder features are critical for compatibility? Compatibility depends on holder form, relief angle, tolerance class, fastening method, size and thickness; ensure the holder matches the SNMN190416 dimensions and clamping style. Is a chipbreaker included with this insert? This variant is supplied without a chipbreaker; chip control should be achieved by selecting a matching chipbreaker geometry or optimising cutting parameters for the workpiece material. What is the corner radius and why does it matter? The corner radius is 1.6 mm; a larger radius increases edge strength and stability, improving performance at higher feeds and reducing the risk of chipping. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
SNMU 120608 AH120 Wendeplatten - Tungaloy
Take advantage of the combination of PVD-coated AH120 carbide and a double-sided chipbreaker to increase material removal rates with minimal axial immersion; this yields stable cutting performance and predictable tool life. Order the insert directly via Metav Werkzeuge or consult our specialists for the matching DoFeed cutter bodies. SNMU 120608 AH120 indexable insert for high-feed milling by Tungaloy A SNMU120608 AH120 indexable insert engineered for high-feed milling, pocketing and face machining within the DoFeed family PVD-coated AH120 carbide grade For high-feed milling and pocketing Square 12 mm plate, 6.35 mm thick Cylindrical hole with double countersink Maximise removal rates with small axial cuts The DoFeed concept is designed to deliver large time‑span volumes while keeping the axial depth of cut low. This insert benefits from a square geometry and a 90° seating angle, enabling very high feed per tooth without increasing axial load. The combination of a low axial immersion and increased feed produces a larger volumetric removal rate per pass, which improves throughput on pocketing and planing operations. The design reduces tool engagement stress and helps maintain stable machining conditions for long production runs. Prolonged edge life and process security The AH120 grade is a PVD-coated carbide developed for resistance to wear and chipping under interrupted and continuous cutting conditions. Its formulation provides a sharp cutting edge that retains geometry under high demands, which supports consistent surface quality and repeatable cycle times. The coating reduces abrasive wear and improves thermal resistance, making the insert suitable where a reliable cutting edge and process security are required rather than frequent regrinding or replacement. Reliable clamping and predictable indexing A precise locating hole — a cylindrical bore with double-sided countersink (40°–60°) — ensures secure seating in the cutter body and repeatable positioning of cutting edges. The double-sided chipbreaker allows indexing of the insert to present a fresh edge without changing plate geometry, while the square form provides multiple usable corners. Overall system behaviour is improved when the insert is used with the matching DoFeed milling body and fastening screws, reducing downtime during tool changes and simplifying inventory management. Clear selection for common milling tasks Specify this insert where high-feed strategies are preferred: pocketing, face machining and high-volume finishing operations. The SNMU120608 AH120 variant offers a 0.8 mm corner radius for a balance between edge strength and surface definition, and a plate thickness of 6.35 mm for stable clamping. When combined with DoFeed cutters and appropriate machining parameters, the result is a productive, process-secure solution that supports consistent part quality and predictable tool life — an asset for batch and continuous production alike. For process-critical high-feed milling, contact Metav Werkzeuge for matching DoFeed cutter bodies and genuine Tungaloy SNMU120608 AH120 inserts — email info@metav-werkzeuge.com or call +49 2822 7131930 Technical Data Article number: 6780140 SKU: 6780140-Tungaloy Manufacturer SKU: TUN6780140 Name: SNMU120608 AH120 Tungaloy insert Core data ISO designation: 120608 Plate size: 12 mm Thickness: 6.35 mm Corner radius: 0.8 mm Relief angle: 0° Insert angle: 90° Special features Material: carbide Coating: PVD Grade: AH120 Chipbreaker: double-sided Hole: cylindrical with double countersink (40°–60°) Series: DoFeed — high-feed milling family Typical use: high-feed milling, pocketing and face machining FAQ What operations is this insert designed for? The insert is intended for high-feed milling operations, particularly pocketing and face machining as part of the DoFeed family. How is the insert secured in the cutter body? The SNMU120608 AH120 insert uses a cylindrical hole with a double-sided countersink (40°–60°) to ensure accurate seating and secure fastening with the appropriate screws. Is the insert reversible or single-sided? The plate features a double-sided chipbreaker and is indexable, allowing use of multiple cutting edges before replacement; this supports continuous production with minimal tool change downtime. Which benefits does the AH120 grade provide? The AH120 grade is a wear- and fracture-resistant PVD-coated carbide designed to keep a sharp edge and ensure process security under demanding milling conditions. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
SNMU 120608 AH3135 Wendeplatten - Tungaloy
Benefit from the combination of productive high‑feed geometry and a wear‑resistant PVD‑coated carbide grade for steady chip control and prolonged edge life. Order the insert directly via Metav Werkzeuge or consult our specialists for application support. SNMU 120608 AH3135 SNMU insert for milling by Tungaloy — DoFeed, double‑sided chipbreaker The SNMU120608 AH3135 is a PVD‑coated carbide indexable insert for high‑feed milling, optimised for pocketing and face milling with small axial depths to deliver high material removal rates. High‑feed DoFeed geometry PVD‑coated AH3135 carbide grade Double‑sided chipbreaker for stability Square insert, 90° angle, r0.8 Productive high‑feed design for higher throughput The DoFeed family is engineered to permit large time‑based chip volumes at very small axial depths, which raises the productive throughput of milling cycles. The insert’s geometry focuses on controlled chip formation and consistent cutting forces so that machining of pockets and planes proceeds with fewer tool changes. By choosing an insert from the DoFeed series, workshops gain a measurable improvement in metal removal rate while maintaining process predictability, making the tool particularly suited to production environments where cycle time and repeatability are decisive. The combination of geometry and secure clamping reduces vibration and supports stable cutting. Durable PVD‑coated grade for edge integrity and process security The PVD‑coated AH3135 grade is formulated to resist wear and chipping under the alternating loads of milling, providing a sharp cutting edge together with reliable performance. A PVD coating enhances surface hardness and thermal resistance at the cutting edge, which contributes to longer edge life and improved surface finish over time. For operations that demand both a keen edge and consistent process behaviour, this grade reduces unexpected edge breakouts and maintains dimensional accuracy across series production. The result is reduced tool consumption and fewer interruptions in machining. Secure geometry and practical mounting for reliable handling A square plate with a 90° cutting angle and a 0.8 mm corner radius balances strength and finishing capability: the radius gives edge robustness for roughing while still permitting acceptable surface quality for semi‑finishing. The insert features a cylindrical hole with double‑sided countersink (40°–60°) to ensure firm clamping and precise seat location in the cutter body. Double‑sided chipbreakers aid chip control on both cutting edges, enabling the use of the insert on multiple edges and simplifying inventory management. The standard plate thickness and size support straightforward tool set‑up and replacement in compatible milling bodies. Application focus and handling notes for production use Designed specifically for milling, the insert is especially effective in high‑feed pocketing and face operations where small axial depths are preferred and high feed per tooth is possible. The system consists of the cutter body, matching indexable plates and screws, enabling a modular approach to tool assembly. Operators should match the insert geometry and grade to the machining parameters and cutter body to exploit the DoFeed advantages fully. When set up correctly, the insert offers a favourable compromise between aggressive material removal and controlled surface integrity. For application advice or to secure stock of Tungaloy SNMU120608 AH3135 inserts, contact Metav Werkzeuge – email info@metav-werkzeuge.com or call +49 2822 7131930 Technical Data Article number: 6780139 Manufacturer SKU: TUN6780139 SKU: 6780139-Tungaloy Model series: DoFeed Material: Carbide Coating / Grade: AH3135 (PVD‑coated) Numbers / Core Technical Data ISO designation: 120608 Plate size: 12 mm Plate thickness: 6.35 mm Corner radius: 0.8 mm Cutting angle: 90° Relief angle: 0° Special features Square plate form Double‑sided chipbreaker Cylindrical hole with double‑sided countersink (40°–60°) With hole System: plug‑in plate for milling cutter bodies Typical applications: high‑feed milling, pocketing, face milling FAQ What machining tasks suit this insert best? The SNMU120608 AH3135 insert is optimised for high‑feed milling, specifically pocketing and face machining where small axial depths and high feed rates are used. How does the AH3135 grade improve performance? AH3135 is a PVD‑coated carbide grade designed to resist wear and chipping, providing a sharp cutting edge and consistent process security for milling operations. What clamping features ensure secure seating of the insert? The insert has a cylindrical hole with a double‑sided countersink (40°–60°), which secures positioning and ensures stable clamping in compatible milling cutter bodies. Can the insert be used on multiple edges? Yes, the plate is double‑sided with chipbreakers on both faces, allowing reindexing to use multiple cutting edges and extend tool life. Which dimensions are relevant when selecting a compatible cutter body? Key dimensions include the plate size (12 mm), thickness (6.35 mm) and ISO designation 120608 to ensure correct fit and alignment. Manufacturer/Responsible: Tungaloy‑NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand‑new product from the manufacturer.
SNMU 120608 AH3225 Wendeplatten - Tungaloy
Take advantage of the combination of PVD-coated AH3225 carbide for extended tool life, the DoFeed high-feed geometry for large material removal at low axial depths, and secure double-sided chip control to keep machining stable and productive. Order the insert directly via Metav Werkzeuge or ask our consultants if needed. SNMU 120608 AH3225 – SNMU indexable insert for milling (Tungaloy) The SNMU120608 AH3225 is a PVD-coated carbide indexable insert from the DoFeed high-feed family, designed for efficient pocketing and face milling where large time-chip volumes are required with small axial engagements. DoFeed high-feed milling family PVD-coated AH3225 carbide for wear resistance Double-sided chipbreaker for secure chip control Square 12 mm insert, 0.8 mm corner radius Boosted productivity through optimised high-feed geometry The DoFeed series is engineered for high-feed milling, where throughput is increased by using large chip volumes with small axial depths. The PVD-coated AH3225 carbide grade combines wear resistance with a sharp, stable cutting edge; this reduces flank wear and upholds dimensional accuracy across long runs. In practice, that means fewer tool changes, more consistent cycle times and a measurable reduction in cost per component. The coated substrate also improves adhesion resistance at elevated temperatures, which supports uninterrupted operation in demanding production environments. Precision edge and mounting for repeatable accuracy A deliberate combination of geometry and form yields predictable results: the square 12 mm format and 6.35 mm thickness give a rigid seating surface, while the 0.8 mm corner radius balances edge strength with surface finish capability. The insert’s cylindrical hole with double-sided countersink (40°–60°) ensures reliable clamping and repeatable positioning in compatible milling bodies. For shops less familiar with radius selection, a 0.8 mm corner radius typically offers a good compromise between edge robustness and the ability to maintain tight tolerances during pocket and face milling operations. Consistent chip control and extended tool life Chip management is central to process security; the double-sided chipbreaker is fashioned to produce controlled swarf even under heavy feed rates, lowering the risk of re-cutting and tool interference. Controlled chips help maintain stable cutting temperatures and reduce the likelihood of built-up edge, which in turn supports consistent surface quality. The combined effect of the chipbreaker geometry and the PVD-coated carbide grade is fewer unplanned interruptions and a higher overall equipment effectiveness (OEE) for milling cells. Practical system integration for workshop efficiency The insert forms part of a complete milling system that includes matching cutters and clamping screws, allowing straightforward integration into existing DoFeed-compatible toolholders. This system approach simplifies inventory management and reduces set-up times. Traceability is straightforward thanks to the manufacturer article number and SKU, which assist purchasing and tool management systems when replenishing stock for production-critical operations. For applications such as pocketing, face milling and heavy trochoidal cuts, the combination of insert geometry and material ensures reliable performance across a range of steels and general milling tasks. Contact Metav Werkzeuge today for application guidance on the Tungaloy SNMU120608 AH3225 indexable insert or to arrange supply through our specialists at info@metav-werkzeuge.com or +49 2822 7131930 Technical data Article number: 6824027 Manufacturer SKU: TUN6824027 SKU: 6824027-Tungaloy Model series: DoFeed Material: Carbide Grade/coating: AH3225 (PVD-coated) Facts Insert size: 12 mm Thickness: 6.35 mm Corner radius: 0.8 mm Relief angle: 0° Cutting angle: 90° Hole style: Cylindrical hole with double-sided countersink (40°–60°) Special features Square insert shape Double-sided chipbreaker Designed for high-feed milling, pocketing and face milling Part of a system with matching milling bodies and screws Robust, wear-resistant PVD-coated carbide grade FAQ What machining tasks is this insert best suited for? The insert is intended for high-feed milling operations such as pocketing and face milling; the DoFeed design of the SNMU120608 AH3225 supports large time-chip volumes at small axial depths for increased productivity. Does the insert have a coating and what benefits does it provide? Yes, the AH3225 grade is PVD-coated; the coating improves wear resistance, reduces edge adhesion and helps maintain process stability under elevated cutting temperatures. How is the insert secured in the cutter body? The SNMU120608 AH3225 features a cylindrical hole with a double-sided countersink (40°–60°) to ensure reliable clamping and repeatable seating in compatible DoFeed toolholders. What does the 0.8 mm corner radius mean for surface finish and tool life? A 0.8 mm corner radius offers a compromise between a robust cutting edge and the ability to produce a good surface finish; it helps prevent premature chipping while maintaining dimensional control in typical milling tasks. Is this insert part of a complete system? Yes, the insert is specified as part of the DoFeed system, which includes matching milling bodies and the required screws for installation to simplify tool management. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
SNMU 120608 T1215 Wendeplatten - Tungaloy
Benefit from the combination of wear resistance, stable cutting-edge performance and efficient material removal for uninterrupted high-feed milling; order the insert directly via Metav Werkzeuge or consult our advisors for application-specific recommendations. SNMU 120608 T1215 indexable insert for high-feed milling by Tungaloy — DoFeed series SNMU 120608 T1215 is a square indexable insert designed for high-feed milling and pocket or face machining in industrial milling applications. High-feed milling for large material removal T1215 carbide grade for wear resistance Double-sided chipbreaker for reliable chip control Square 12 mm insert with 0.8 mm corner radius Greater productivity through high-feed design The DoFeed family is engineered specifically for high-feed milling, enabling significantly larger time chip volumes while using small axial depths of cut. This geometry optimises metal removal rates without requiring deep cuts, which shortens cycle times in pocketing and face-milling operations. The combination of the insert shape and cutting edge ensures consistent engagement with the workpiece, reducing vibration and improving process reliability. Balanced performance from the T1215 grade The T1215 carbide grade delivers a deliberate balance of wear resistance, toughness and cutting-edge stability, which supports productive machining across varied tasks. This blend reduces the frequency of edge changes and helps maintain surface quality during longer runs. For milling tasks where chip flow and tool life matter, the grade supports repeatable outcomes and predictable maintenance intervals. Practical geometry and secure mounting for workshop use A square insert with a 12 mm size, 6.35 mm thickness and a 0.8 mm corner radius provides a robust cutting edge while allowing multiple indexings per insert. The insert is supplied with a hole and a cylindrical hole plus double-sided countersink (40°–60°) to fit common milling bodies; the system comprises the milling body, matching indexable inserts and fixing screws, ensuring straightforward integration into existing toolholders. The 90° lead angle suits general-purpose face milling, while the 0° relief angle promotes stable engagement. Reliable chip control and application suitability Equipped with a double-sided chipbreaker, the insert promotes predictable chip formation and evacuation during high-feed passes. This reduces the risk of chip entanglement and supports safer, cleaner operation at higher material removal rates. The DoFeed geometry and chip control features are particularly suited to pocket milling and planing operations where maintaining surface integrity and process consistency is essential. Contact Metav Werkzeuge for tailored advice on integrating Tungaloy DoFeed inserts into production, or request application guidance via info@metav-werkzeuge.com or +49 2822 7131930 Technical details Article number: 6780142 Manufacturer SKU: TUN6780142 SKU: 6780142-Tungaloy Manufacturer: Tungaloy Facts ISO designation: 120608 Insert size: 12 mm Thickness: 6.35 mm Corner radius: 0.8 mm Lead angle: 90° Relief angle: 0° Special features Grade: T1215 (Tungaloy carbide) Model series: DoFeed — high-feed milling family Insert shape: square Chipbreaker: double-sided Hole: with hole; cylindrical hole + double-sided countersink (40°–60°) Application: milling (pocket and face milling; high-feed milling) FAQ What machining tasks is this insert intended for? The insert is intended for high-feed milling tasks such as pocketing and face milling; the DoFeed geometry is optimised for large time chip volumes at small axial depths. Which grade and material does the insert use? The insert uses the T1215 Tungaloy carbide grade, selected to balance wear resistance and toughness for stable cutting-edge performance. How is the insert mounted in a milling cutter? The system comprises a milling body, matching indexable inserts and fixing screws; the insert is supplied with a centred hole and a cylindrical hole plus double-sided countersink for secure clamping. Does the insert support good chip control? Yes, the double-sided chipbreaker is designed to promote reliable chip formation and evacuation during high-feed operations, improving process stability. What are the key geometric dimensions to consider when selecting the insert? Key dimensions are the 12 mm size, 6.35 mm thickness, 0.8 mm corner radius, 90° lead angle and 0° relief angle; these influence edge strength, indexing and compatibility with toolholders. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
SNMU 120608 T3225 Wendeplatten - Tungaloy
Benefit from the combination of the DoFeed high-feed geometry, the wear-resistant T3225 grade and a robust carbide construction to increase material removal rates with small axial depths; order the insert directly via Metav Werkzeuge or consult our specialists for grade and clamping advice. SNMU 120608 T3225 SNMU – indexable insert for milling by Tungaloy The SNMU120608 T3225 Tungaloy indexable insert is a square, double-sided cutting plate designed for high-feed milling, pocketing and face operations in production environments. High-feed family for large material removal Tungaloy T3225 grade for wear resistance Double-sided chipbreaker for stable chips Square 12 mm plate with 0.8 mm corner radius Faster removal with reduced axial engagement The DoFeed series is engineered to deliver high-feed milling capability: greater time-material volumes are removed while keeping the axial depth of cut low, which reduces tool load and machine stress. The combination of the family geometry and a carbide substrate makes this insert especially effective for productive finishing and roughing passes. The specified T3225 grade provides a balanced mix of wear resistance and edge toughness, prolonging service life and reducing tool change frequency. For production planners and process engineers, this translates into predictable cycle times and fewer interruptions for regrinding or replacement. Reliable chip control and mechanical stability Chip control and secure clamping are essential for repeatable results; the plate's double-sided chipbreaker design promotes consistent chip formation in high-feed conditions and helps prevent recutting. The insert features a central hole with a cylindrical bore and double-sided countersink (40°–60°) to ensure secure clamping in the cutter body, combined with a 90° seating angle for accurate positioning. The 0.8 mm corner radius improves edge strength at interrupted cuts and supports stable cut progression. These characteristics reduce vibration and contribute to a finer surface finish without sacrificing material removal rate. straightforward integration and shop-floor advantages The system comprises the milling body, matching indexable plates and fastening screws, which simplifies procurement and assembly in existing tool holders. The square plate form (12 mm) and standard ISO designation facilitate stock management and tool nesting. For workshop managers, the practical benefit is a reliable, off-the-shelf component that fits common high-feed cutters and is easy to replace. Application versatility extends to pocket milling and face milling where the DoFeed geometry and T3225 grade deliver consistent performance across a broad range of steels and alloyed materials commonly encountered in production. Request tailored process advice or order the Tungaloy SNMU120608 T3225 insert via Metav Werkzeuge for rapid integration into existing milling systems; contact our consultants for recommended cutting data and clamping options Technical Data Article number: 6780141 SKU: 6780141-Tungaloy Manufacturer article number: TUN6780141 Model series: DoFeed Application: milling Plate designation: SNMU120608 Facts Plate size: 12 mm Thickness: 6.35 mm Corner radius: 0.8 mm Relief angle: 0° Seating angle: 90° Special features Material: carbide Grade/coating: T3225 Plate shape: square Hole: with hole Hole style: cylindrical hole + double-sided countersink (40°–60°) Chipbreaker: double-sided Typical applications: high-feed milling, pocketing, face milling System composition: milling body, matching inserts and screws FAQ What machining tasks suit this insert best? The SNMU120608 T3225 insert is intended primarily for high-feed milling, pocketing and face operations where large time‑material volumes are required at small axial depths. Which material is the cutting plate made from? The plate is manufactured from carbide and supplied in the Tungaloy T3225 grade to combine wear resistance with edge stability for production use. How does the chipbreaker affect milling performance? The double-sided chipbreaker promotes uniform chip formation and evacuation in high-feed scenarios, improving surface quality and reducing the risk of recutting. Is special clamping hardware required for this plate? The plate is supplied with a cylindrical hole and double-sided countersink to match standard cutter bodies; secure clamping is achieved using the appropriate screw and seating in the milling body. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
SNMU 120612 AH3135 Wendeplatten - Tungaloy
Take advantage of a PVD-coated carbide grade and a double-sided chipbreaker for consistent, process-secure milling; order directly via Metav Werkzeuge or consult our specialists if further application data is required. SNMU120612 AH3135 – Indexable milling insert for milling, PVD-coated carbide, 90° geometry (Tungaloy) SNMU120612 AH3135 is a square indexable insert designed for use in Tungaloy milling systems, combining a sharp cutting edge with enhanced breakage resistance for reliable, productive milling operations. PVD-coated carbide for wear resistance Sharp cutting edge and process security Double-sided chipbreaker for versatile cutting Square form with 90° cutting angle Central hole with countersink for secure clamp Extended tool life through high-performance coating The PVD-coated carbide substrate delivers improved wear resistance and a consistently sharp edge, which together reduce downtime and tool changes. The coating on this insert is the AH3135 grade, optimised for milling applications where both a sharp cutting edge and process security are required. In practice, this means longer intervals between indexings and steadier surface finishes, with the coating helping to limit flank wear and microchipping under typical milling loads. Secure seating and repeatable clamping for stable processes Designed with a central hole and a cylindrical hole plus a double-sided countersink (40°–60°), the insert ensures secure clamping and repeatable positioning in compatible tool bodies. The square geometry and a plate thickness of 6.35 mm provide a rigid contact area that minimises movement under load, supporting consistent cutting forces and predictable tool life. Correct matching of insert seat, clamping screw and cutter body is essential to exploit these mechanical advantages. Versatile geometry for multiple milling tasks The square form with a 90° cutting angle and a 1.2 mm corner radius suits a range of milling operations, from face and shoulder milling to slotting and contouring depending on the associated tool family. The double-sided chipbreaker allows two usable cutting faces per side, improving economy and flexibility in the workshop. Such geometry helps reduce inventory complexity by providing a single insert solution for several machining tasks while maintaining reliable chip control. Practical application guidance and performance expectations As part of a matched Tungaloy milling system, this indexable insert is intended for productive, process-secure metalworking where a sharp edge and resistance to breakage are priorities. The insert’s construction supports stable chip formation and consistent cutting behaviour, which contributes to predictable component quality and reduced rework. For machine parameters, speeds and feeds should be selected according to the tool body family and material being machined to achieve the best balance between tool life and productivity. Contact Metav Werkzeuge for application advice or to secure the SNMU120612 AH3135 for robust, process-secure milling — email info@metav-werkzeuge.com or call +49 2822 7131930 to discuss suitability for specific tool holders and workpiece materials Technical Data Article number: 6780143 Manufacturer SKU: TUN6780143 Supplier SKU: 6780143-Tungaloy Material: Hartmetall Model series: Fräswendeschneidplatten Facts Corner radius: 1.2 mm Size: 12 mm Thickness: 6.35 mm Relief angle: 0° Cutting angle: 90° Special features Square form Double-sided chipbreaker Central hole with cylindrical hole and double-sided countersink (40°–60°) Coating: AH3135 (PVD-coated carbide) Applications: face, shoulder, slot, high-feed and contour milling (depending on tool family) FAQ What milling operations are suitable for this insert? This insert is suited to face, shoulder, slot, high‑feed and contour milling when used in the correct Tungaloy milling body and with matching geometry. Which geometry and dimensions define the cutting behaviour? The insert features a 90° cutting angle, 1.2 mm corner radius and 6.35 mm thickness, giving consistent cutting performance and rigidity for demanding milling tasks. How is the insert clamped and how does that affect stability? A central hole with a cylindrical bore and a double‑sided countersink (40°–60°) ensures secure clamping and repeatable seating when the cutter body and screw are matched to the insert form. What is the coating and material of the insert? The insert is made of PVD-coated carbide in the AH3135 grade, offering enhanced wear resistance and edge stability for milling applications requiring both sharpness and process security. Can the insert be indexed to use multiple edges? As a double-sided, square insert with a reversible design, it provides multiple usable edges, improving tool economy when correctly indexed in the compatible cutter body. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
SNMU 120612 AH3225 Wendeplatten - Tungaloy
Take advantage of the PVD-coated AH3225 grade and the square 12 mm form with 1.2 mm corner radius for stable, chipping-resistant milling; order the insert via Metav Werkzeuge or consult the technical team for application matching. SNMU 120612 AH3225 indexable insert for milling (square, R1.2) — Tungaloy The SNMU120612 AH3225 is an indexable insert for Tungaloy milling systems, engineered for face, shoulder, groove, high-feed and contour milling where a sharp cutting edge and reliable process security are essential. PVD-coated carbide AH3225 Chipping- and wear-resistant grade Square 12 mm, R1.2 corner radius Double-sided chipbreaker Cylindrical hole with double countersink Consistent performance from a wear-resistant PVD grade The PVD-coated AH3225 grade delivers stable chip formation and a durable cutting edge suited to demanding milling operations. As a PVD-coated carbide insert, it combines a tough substrate with a hard, wear-resistant coating to reduce flank wear and delay edge breakdown, which leads to longer intervals between indexings and predictable cycle times. For production environments that prioritise uptime and repeatable results, this combination reduces rework and supports higher overall productivity. Geometry and clamping designed for reliable machining A square plate with a 1.2 mm corner radius and 90° included angle provides a balance between cutting strength and edge sharpness, making the insert suitable for general shoulder and contour milling. The double-sided chipbreaker controls chip flow on each cutting edge, helping to avoid built-up edge and to maintain surface quality. The insert is supplied with a cylindrical hole and double-sided countersink (40°–60°) to ensure secure clamping in compatible cutter bodies; correct seat and body matching are required to achieve rated performance. System compatibility and typical applications These indexable inserts are intended for use in matching Tungaloy milling systems and form part of a modular tool assembly consisting of cutter body, insert, clamp screw and, if needed, a shim. Typical operations include face, shoulder, slot, high-feed and contour milling depending on the assigned tool family. The insert’s combination of a sharp edge and process security makes it particularly suitable where consistent surface finish and edge integrity are required across batch production. Discuss application-ready Tungaloy SNMU 120612 AH3225 inserts with Metav Werkzeuge—technical consultants are available by email at info@metav-werkzeuge.com or by phone at +49 2822 7131930 Technical Data Article number: 6824028 SKU: 6824028-Tungaloy Manufacturer SKU: TUN6824028 Grade / coating: AH3225 (PVD-coated carbide) Material: Carbide Model series: Milling indexable inserts Dimensions & core data Size: 12 mm Thickness: 6.35 mm Corner radius: 1.2 mm Relief angle: 0° Included angle: 90° Features & compatibility Shape: square Hole: cylindrical hole with double countersink (40°–60°) Chipbreaker: double-sided Edge form: sharp cutting edge for process security Application: milling (face, shoulder, slot, high-feed, contour) System requirement: compatible with Tungaloy milling bodies; insert seat and cutter must match FAQ What milling operations are suitable for this insert? The SNMU120612 AH3225 indexable insert is intended for face, shoulder, slot, high-feed and contour milling within Tungaloy milling systems; the exact application depends on the assigned cutter family. Which coating and substrate are used on this insert? This insert uses the AH3225 specification: a PVD-coated carbide grade designed for wear and chipping resistance during milling. How is the insert clamped and located in the cutter body? The insert features a cylindrical hole with a double-sided countersink (40°–60°) and is secured by the cutter body’s clamping screw and any required shim; correct seat geometry and matching cutter body are essential. How does the corner radius affect cutting performance? The 1.2 mm corner radius provides greater edge strength than a smaller radius while maintaining a suitably sharp cutting profile for good surface finish and robust metal removal. Is the insert reversible or indexable on both sides? The plate has a double-sided chipbreaker and is designed to provide multiple usable cutting edges, enabling indexable reuse in compatible assemblies. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
SNMU 120612 T1215 Wendeplatten - Tungaloy
Take advantage of the combination of consistent edge stability, broad material coverage and simple integration into Tungaloy milling systems for uninterrupted production. The square indexable insert offers a reliable corner radius and a secure seating design, supporting plan, shoulder and contour milling operations. Order directly via Metav Werkzeuge or consult our specialists for application advice. SNMU120612 T1215 milling insert by Tungaloy The SNMU120612 T1215 is a square indexable insert for milling, designed for plan, shoulder, slot, high‑feed and contour milling where a robust carbide grade and stable cutting edge are required Tungaloy grade T1215 for milling Square 12 mm format 1.2 mm corner radius Cylindrical hole with countersink High productivity through engineered grade and geometry The combination of the T1215 grade and the insert geometry delivers a balance of wear resistance and edge toughness that supports sustained throughput in production environments. The carbide body is optimised to maintain a stable cutting edge under mixed cutting conditions; this reduces unscheduled interruptions and contributes to predictable tool life. Thanks to the 1.2 mm corner radius and the 90° profile, the insert is particularly suited to operations that require accurate shoulder faces and consistent corner transitions. Translating material and geometric properties into process reliability, the design helps to reduce variability in surface finish and dimensional accuracy. Versatile application range and clear technical fitment The insert is intended for use within compatible Tungaloy milling systems where plate seat, geometry and milling body are matched. The square format and double‑sided configuration mean the insert can be rotated to present fresh cutting edges, increasing utilisation per part. The cylindrical hole with double‑sided countersink (40°–60°) secures the insert in the cutter body while ensuring correct axial and radial seating. Typical tasks include planing, shoulder work, slotting, high‑feed passes and complex contouring, depending on the assigned tool family. Explaining the seat compatibility and system requirements reduces the risk of incorrect installation and helps maintain cutting performance. Practical handling and installation advantages With a plate thickness of 6.35 mm and the standard hole style, the insert is straightforward to clamp into corresponding milling bodies. The system setup—milling body, insert, clamp screw and, where needed, shim—follows established workshop procedures, making changeovers efficient and repeatable. The lack of a relief angle (0°) on the insert face is reflected in the cutter design and must be accommodated by a matched toolholder geometry. Clear mechanical fitment avoids canting or misalignment that could otherwise accelerate wear or compromise component quality. Why this grade supports dependable production Choosing a purpose‑designed grade such as T1215 means prioritising a cutting material tuned for a range of milling tasks: it extends useful tool life through stable chip control while maintaining cutting‑edge integrity under intermittent loads. For manufacturers aiming to reduce downtime and maintain consistent part quality, the insert’s combination of carbide construction, defined corner radius and secure mounting supports predictable process windows. When paired with the correct Tungaloy milling body, the result is a productive, reliable milling solution that integrates with existing machining strategies. For production guidance or application matching of genuine Tungaloy SNMU120612 T1215 inserts, contact Metav Werkzeuge for expert advice or to place an order: info@metav-werkzeuge.com • +49 2822 7131930 Technical data Article number: 6780144 SKU: 6780144-Tungaloy Manufacturer SKU: TUN6780144 Material: carbide Grade: T1215 Facts Insert designation: SNMU120612 Size: 12 mm Thickness: 6.35 mm Corner radius: 1.2 mm Relief angle: 0° Included hole: with hole Hole style: cylindrical hole + double‑sided countersink (40°–60°) Shape: square Angle: 90° Special features Model series: milling indexable inserts Chipbreaker: double‑sided Typical applications: plan, shoulder, slot, high‑feed and contour milling (tool family dependent) System components: milling body, indexable insert, clamp screw, possible shim Intended for use with Tungaloy milling systems Carbide construction for wear resistance and edge stability FAQ Is this insert compatible with non‑Tungaloy milling bodies? Compatibility requires matching seat geometry, insert profile and clamping method; the SNMU120612 T1215 insert is designed for use in Tungaloy milling systems and must be fitted into bodies with the corresponding seat and clamp arrangement to ensure correct performance. What does the T1215 grade mean for machining? The T1215 grade denotes a Tungaloy carbide formulation optimised for milling, offering a balance of wear resistance and toughness suited to a broad range of operations where stable edge life and chip control are important. How should the cylindrical hole with countersink be used? The cylindrical hole with double‑sided countersink (40°–60°) provides secure axial and radial locating when clamped; it ensures repeatable seating within the cutter body and contributes to stable cutting geometry. Which milling tasks are most suited to this square insert? Square geometry with a 1.2 mm corner radius and 90° profile is appropriate for planing, shoulder work, slotting, high‑feed and contour milling, depending on the assigned tool family and cutter body. Does the insert require any special shims or screws? Standard clamping hardware used in the compatible Tungaloy milling body is required; system setup typically includes the milling body, insert, clamp screw and, where specified, a supporting shim to achieve correct axial height and alignment. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
SNMU 120620 AH3135 Wendeplatten - Tungaloy
Take advantage of the combination of PVD-coated carbide wear resistance, a double-sided chipbreaker for flexible indexing and a precise 12 mm square form with a 2 mm corner radius for consistent milling performance. Order the insert directly via Metav Werkzeuge or consult our specialists for application support. SNMU 120620 AH3135 – Milling insert SNMU120620 for Fräsen by Tungaloy A SNMU120620 AH3135 indexable milling insert for Tungaloy milling systems, engineered for face, shoulder, slot and high-feed milling where a sharp cutting edge and process security are essential. PVD-coated carbide for extended wear resistance Double-sided chipbreaker for versatile cutting Square 12 mm form with 6.35 mm thickness Cylindrical hole with countersink for secure clamping Longer tool life through hard-wearing coating and substrate The PVD-coated cemented carbide substrate delivers demonstrable durability in interrupted and continuous milling operations. The AH3135 grade is specified as a wear- and break-resistant compound, which supports a consistently sharp cutting edge and reduced edge chipping. For production environments seeking predictable tool life and fewer index cycles, this combination reduces downtime and helps maintain surface quality across runs. Reliable chip control and flexible indexing for varied milling tasks Equipped with a double-sided chipbreaker, the insert enables stable chip formation across a range of cutting conditions. The geometry is optimised for face and contour milling in compatible tool families, improving evacuation and reducing re-cutting of chips. As a consequence, machine loads remain steady and tool-change frequency is reduced, which supports throughput and process reliability on mixed-batch production. Precise seating and secure clamping for process security The insert features a cylindrical hole with double-sided countersink (40°–60°) that ensures reproducible clamping in Tungaloy milling bodies. The square 12 mm form and 6.35 mm thickness combine with a 0° relief to offer a robust seating surface; this reduces the risk of micro-movement under load and supports repeatable part tolerances. Correct matching of insert seat, geometry and cutter body is required for optimum performance. Applications and operational benefits in one solution Designed for a broad set of milling operations, the indexable plate is suitable where a sharp edge and process security are required rather than extensive material-specific claims. The 2 mm corner radius provides a balance between edge strength and achievable surface finish, while the 90° orientation supports shoulder and face milling tasks. Using this insert in a matching Tungaloy system simplifies logistics by standardising on a proven geometry and clamping method. For technical advice on integrating Tungaloy SNMU120620 AH3135 into existing cutters or to verify compatibility with specific milling bodies, contact Metav Werkzeuge at info@metav-werkzeuge.com or call +49 2822 7131930 — our consultants will advise on application and selection. Technical data Article number: 6777924 Manufacturer SKU: TUN6777924 Material: Cemented carbide Facts ISO designation: 120620 Plate size: 12 mm Plate thickness: 6.35 mm Corner radius: 2 mm Relief angle: 0° Main angle: 90° Countersink range: 40°–60° Special features Grade: AH3135 (PVD-coated) Double-sided chipbreaker Square plate form Cylindrical hole with double-sided countersink Intended application: milling (face, shoulder, slot, high-feed, contour) Requires technically matching Tungaloy milling bodies and insert seats FAQ What primary milling tasks is this insert intended for? The SNMU120620 AH3135 is intended for face, shoulder, slot, high-feed and contour milling within compatible Tungaloy systems where a sharp cutting edge and process security are required. What are the key dimensions of the insert? The insert is a square 12 mm plate with a thickness of 6.35 mm and a corner radius of 2 mm; ISO designation 120620. How is the insert clamped in the milling body? Clamping uses the cylindrical hole with a double-sided countersink (40°–60°); secure seating depends on a matching Tungaloy milling body and correct screw/tolerancing. Is the insert suitable for indexing on both sides? Yes, the double-sided chipbreaker indicates the insert can be indexed to use both active faces, extending usable life per insert. What substrate and coating are used on this insert? The SNMU120620 AH3135 uses a PVD-coated cemented carbide substrate; the AH3135 grade is described as wear- and break-resistant for milling applications. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
SNMU 120620 AH3225 Wendeplatten - Tungaloy
Take advantage of the combination of process security, wear-resistant PVD coating, and a robust 2.0 mm corner radius for consistently productive milling operations. Order or request application advice via Metav Werkzeuge to ensure the insert is matched correctly to the milling body and clamping system. SNMU120620 AH3225 Tungaloy indexable insert – 90° square insert for milling SNMU120620 AH3225 Tungaloy indexable insert designed for secure, wear-resistant cutting in Tungaloy milling systems, suitable for face, shoulder, slot and contour milling. PVD-coated carbide grade AH3225 2.0 mm corner radius for robust edges Square insert with 90° cutting geometry Cylindrical hole with double countersink Reliable cutting performance for stable production output The PVD-coated carbide grade AH3225 delivers a balance of wear resistance and edge sharpness that supports repeatable machining cycles. The coating reduces flank and crater wear under typical milling parameters while the substrate material maintains toughness to resist chipping. This combination increases tool life and reduces unscheduled tool changes, leading to measurable improvements in machining uptime and predictable part quality. Consistent edge stability and improved chip control A 2.0 mm corner radius together with the double-sided chipbreaker provides controlled chip formation and protects the cutting edge during interrupted cuts. The cylindrical hole with dual countersink (40°–60°) ensures precise clamping and axial location on the cutter body, lowering the risk of insert movement under high loads. Explained simply: the chipbreaker shapes and evacuates swarf, while the clamping geometry keeps the insert seated securely, both of which support reliable surface finish and repeatable tolerances. System compatibility and application-focused design The SNMU120620 AH3225 insert is produced for Tungaloy milling systems and requires matching of insert seat, geometry and milling body for correct function. With a 6.35 mm thickness, 12 mm size and square form offering a 90° cutting angle, the insert is suitable for face, shoulder, groove, high-feed and contour milling tasks depending on the chosen cutter family. The design promotes flexible utilisation across general milling operations where process security and stable chip control are priorities. Contact Metav Werkzeuge for tailored application recommendations on Tungaloy AH3225 inserts and to ensure correct seat and geometry selection — email info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: 6824029 Manufacturer SKU: TUN6824029 SKU: 6824029-Tungaloy WPL designation: SNMU120620 Numbers / Core technical data Corner radius: 2.0 mm Cutting angle: 90° Insert thickness: 6.35 mm Insert size: 12 mm Relief angle: 0° Designs / Special features Material: carbide (PVD-coated) AH3225 Insert shape: square Hole: with cylindrical hole + double-sided countersink (40°–60°) Chipbreaker: double-sided Typical use: milling (face, shoulder, slot, high-feed, contour) FAQ What machine systems is this insert designed for? The SNMU120620 AH3225 insert is intended for use in Tungaloy milling systems where the insert seat, geometry and cutter body are specified to match the insert. Which applications are suitable for this insert? Typical applications include face milling, shoulder milling, slotting, high-feed and contour milling, depending on the associated cutter family and machining parameters. What advantage does the AH3225 grade provide? The AH3225 grade offers a PVD-coated carbide that combines wear resistance with a sharp cutting edge, improving tool life and process security under standard milling conditions. How does the corner radius affect the cut? A 2.0 mm corner radius increases edge strength and reduces chipping risk, which benefits interrupted cuts and operations with high load variation. Is the insert clamping robust enough for heavy milling? The cylindrical hole with double countersink and the insert’s geometry ensure precise clamping and axial positioning, supporting stable clamping under elevated cutting forces. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
SNMU 120620 T1215 Wendeplatten - Tungaloy
Take advantage of the combination of high wear resistance, reliable edge stability and straightforward compatibility with Tungaloy milling systems for consistent production results. Order the insert directly via Metav Werkzeuge or consult our specialists for selection support. SNMU120620 T1215 — Square indexable milling insert, 2 mm corner radius, by Tungaloy The SNMU120620 T1215 is a square indexable insert designed for a wide range of milling tasks, offering robust edge life and compatibility with Tungaloy milling bodies for planing, shoulder, slot, high-feed and contour milling. Square 12 mm insert, 6.35 mm thickness Grade T1215 carbide for milling performance 2 mm corner radius for robust edge life Cylindrical hole with double-sided countersink Maximise uptime with controlled wear and repeatable results The SNMU120620 grade combines a purpose-developed T1215 compound with a square design to deliver stable chip formation and prolonged service intervals. The carbide composition offers a balance of hardness and toughness that reduces flank wear under continuous milling loads, while the double-sided chipbreaker supports consistent chip control in mixed operations. This results in fewer tool changes and predictable component tolerances, which improves production planning and reduces unplanned downtime. Simple integration into Tungaloy milling systems for reliable clamping A defined seat geometry and a cylindrical hole with double-sided countersink (40°–60°) ensure secure fixation and correct axial positioning in compatible cutter bodies. The insert’s 6.35 mm thickness and square 12 mm form make orientation straightforward and permit multiple indexings before replacement. For machining centres and toolrooms, this means easier stocking logic and fast changeovers, since the insert mates precisely with Tungaloy clamping screws and underlays when the cutter body and insert geometry are matched. Versatile performance across common milling operations Designed for diverse milling tasks, the insert supports planing, shoulder, slotting, high-feed and contour milling depending on the chosen tool family. The 2 mm corner radius offers a compromise between edge strength and surface finish, making the component suitable for medium- to heavy-duty passes where edge robustness is critical. Explanation: a larger corner radius distributes cutting forces across a greater area, reducing chipping risk and stabilising the cutting edge in interrupted cuts. For technical advice on selecting the correct SNMU120620 T1215 insert for specific cutter bodies or component materials, contact Metav Werkzeuge — our advisers provide application-oriented guidance by email or phone and can help match insert and cutter geometry for optimal results. Technical Data Article number: 6777925 Manufacturer SKU: TUN6777925 SKU: 6777925-Tungaloy Facts Corner radius: 2 mm Thickness: 6.35 mm Size: 12 mm Angle: 90° ISO designation: 120620 Special features Material: carbide Grade: T1215 Plate form: square Hole: with cylindrical hole + double-sided countersink (40°–60°) Chipbreaker: double-sided Typical application: milling (planing, shoulder, slot, high-feed, contour) System: insert for Tungaloy milling systems FAQ What material is the insert made of? The SNMU120620 T1215 insert is manufactured from carbide, using the Tungaloy T1215 grade to combine wear resistance and edge stability. Which milling tasks suit this insert? This indexable insert is suited to planing, shoulder, slot, high-feed and contour milling, depending on the selected tool family and cutter body. How is the insert fixed in the cutter body? The SNMU120620 features a cylindrical hole with a double-sided countersink (40°–60°) to ensure correct clamping and repeatable seating in compatible Tungaloy milling bodies. What does the 2 mm radius mean for machining? A 2 mm corner radius offers enhanced edge strength and improved resistance to chipping, supporting medium to heavy milling passes with better surface consistency. Is this insert double-sided or single-sided? The SNMU120620 is designed with a double-sided chipbreaker, allowing multiple indexings to extend effective tool life. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
SNMU 1307AN AH120 Wendeplatten - Tungaloy
Take advantage of the combination of a PVD-coated carbide AH120 grade for superior wear resistance and a 13 mm square geometry that ensures reliable clamping and repeatable edge position; these properties support consistent milling performance and reduced regrinding intervals. Order the SNMU1307AN AH120 insert directly via Metav Werkzeuge or ask our consultants for tailored advice. SNMU1307AN AH120 SNMU square indexable insert for milling by Tungaloy SNMU1307AN AH120 is a precision square indexable insert intended for face, shoulder, slot, high-feed and contour milling within matching Tungaloy milling systems. SNMU geometry for secure seat fit PVD-coated carbide AH120 for wear resistance Double-sided chipbreaker for stable chip control Cylindrical hole with 40°–60° countersink Consistent cutting performance through hardened edge control The insert delivers a sharp cutting edge with a zero corner radius, enabling precise finishing passes and consistent dimensional results. The combination of a robust substrate and a PVD-coated carbide surface reduces adhesive and abrasive wear, which in practice extends the interval between tool changes and lowers overall machining cost per component. For production environments where predictable tool life and minimal variation in surface finish are essential, this geometry offers measurable stability and process reliability. Secure mounting and system compatibility that minimise downtime Designed as part of Tungaloy milling systems, the plate geometry and seating must match the cutter body to ensure correct clamping and repeatable index positions. The insert features a 13 mm square form and a plate thickness of 7.94 mm, together with a cylindrical hole and a double-sided countersink (40°–60°) to allow precise axial and radial fixation. Correctly matched seating reduces chatter, simplifies changeover and improves the repeatability of component tolerances across batches. Material and coating explained — why AH120 is suitable for demanding milling The cutting element is a PVD-coated hardmetal grade identified as AH120, formulated to resist fracture and edge breakdown under interrupted cuts. The substrate is hardmetal (carbide), offering toughness, while the PVD coating provides a thin, adherent wear layer that helps retain a sharp edge and resists built-up edge formation. In practical terms, this means the insert maintains cutting geometry longer, gives consistent tool life across similar components and supports higher productivity without sacrificing surface quality. Operational advantages and recommended milling uses With a double-sided chipbreaker, the insert controls chip form in a range of feed rates and depths of cut, which simplifies chip evacuation and reduces the risk of recutting. The square format allows multiple indexing positions, optimising utilisation of each insert. Typical applications include face milling, shoulder milling, slotting and contouring where a reliable sharp edge and process security are required. For optimal results, match the insert to a compatible Tungaloy cutter body and select cutting parameters that reflect workpiece material and rigidity of the set-up. For applications requiring high process security choose the Tungaloy SNMU1307AN AH120 PVD-coated indexable insert and contact Metav Werkzeuge for application support and ordering at info@metav-werkzeuge.com or +49 2822 7131930 Technical data Article number: 6735440 SKU: 6735440-Tungaloy Manufacturer SKU: TUN6735440 Model series: Milling indexable inserts Manufacturer: Tungaloy Facts Size: 13 mm Thickness: 7.94 mm Shape: square Included hole: with hole Hole style: cylindrical hole + double-sided countersink (40°–60°) Relief angle: 0° Corner radius: 0 mm Included angle: 90° Special features PVD-coated carbide Grade AH120 Double-sided chipbreaker Square plate for multiple indexing Cylindrical hole with double-sided countersink For face, shoulder, slot, high-feed and contour milling Sharp cutting edge for high process security Compatible with Tungaloy milling systems FAQ What is the main application of this insert? The SNMU1307AN AH120 Tungaloy indexable insert is intended for milling operations such as face, shoulder, slot, high-feed and contour milling when used in a compatible milling body. Which material is the cutting part made from? The cutting part is formed from hardmetal (carbide) with a PVD coating specified by the AH120 grade to enhance wear and chipping resistance. How does the hole and countersink affect clamping? The cylindrical hole combined with a double-sided countersink (40°–60°) provides reliable axial fixation and repeatable seating, which reduces vibration and improves dimensional consistency for each indexed position. Is the insert suitable for finishing operations? Yes, the zero corner radius and sharp cutting edge make the insert suitable for finishing passes where accurate edges and good surface quality are required. What should be checked before fitting the insert to a cutter body? Ensure the plate seat geometry and clamping screw arrangement of the cutter body match the insert specification; correct matching of insert and body is necessary for safe, repeatable operation. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
SNMU 1307AN AH3135 Wendeplatten - Tungaloy
Take advantage of PVD-coated carbide in the AH3135 grade and the double-sided chipbreaker for longer tool life and reliable chip control; paired with secure clamping via the central hole and countersink, this combination supports consistent milling performance and reduced downtime. Order the insert directly via Metav Werkzeuge or consult the technical team for application matching. SNMU 1307AN AH3135 Tungaloy indexable insert for milling, PVD-coated carbide, square 90° A SNMU1307AN AH3135 indexable insert engineered for diverse milling tasks, providing wear- and fracture-resistant performance in face, shoulder, slot, high-feed and contour milling within compatible Tungaloy milling systems PVD-coated carbide grade AH3135 Double-sided chipbreaker for efficient chip control Square 90° geometry, 13 mm size Central hole with countersink for secure clamping Consistent cutting performance and extended edge life The AH3135 grade is a PVD-coated carbide developed for milling applications where a sharp cutting edge and process security are demanded. The coating delivers improved resistance to abrasion and built-up edge, while the substrate provides fracture toughness; together these features reduce flank wear and maintain cutting geometry over repeated indexing. This results in more predictable tool life and consistent surface finish on workpieces made from common milling materials. The combination of coating and substrate enables stable, repeatable passes and supports higher productivity through fewer insert changes. Secure clamping and system compatibility for reliable operation Designed to fit Tungaloy milling systems, the insert’s square 90° geometry and central cylindrical hole with a double-sided countersink (40°–60°) ensure robust seating and reliable torque transmission to the cutter body. The double-sided chipbreaker aids controlled chip formation across both cutting edges, improving evacuation and reducing heat build-up in the cut. The plate thickness of 7.94 mm and plate size 13 mm contribute to a rigid interface with the toolholder, lowering the risk of vibration and chattering during heavy cuts. Correct matching of seat, geometry and body is essential to exploit these mechanical advantages and to ensure repeatable clamping behaviour. Application scope and production benefits In manufacturing environments that require process stability, the insert supports a range of milling operations — from finishing shoulders to high-feed roughing — with an emphasis on consistent results and reduced rework. The AH3135 grade is specified for operations where both wear resistance and edge integrity are crucial, enabling longer uninterrupted cycles and improved part-to-part consistency. By choosing an insert with a reliable chip control design and secure clamping features, intervals between tool changes are extended, set-up times fall and overall machining throughput increases. This makes the insert a practical choice for shops focused on efficiency and repeatable quality when integrated into the correct milling body. For technical matching, availability and to request a suitability assessment referencing SKU TUN6735439, contact Metav Werkzeuge — their specialists will advise on the optimal combination of insert grade and cutter body for the intended milling strategy. Technical data Article number: 6735439 Manufacturer SKU: TUN6735439 Label: SNMU1307AN AH3135 Tungaloy-indexable insert Model series: Milling indexable inserts Material: Carbide Grade/coating: AH3135 (PVD-coated) Facts Plate size: 13 mm Plate thickness: 7.94 mm Geometry angle: 90° Clearance angle: 0° Corner radius: 0.00 mm Special features Square plate form, two usable cutting edges per side (double-sided) Central hole with cylindrical bore and double-sided countersink (40°–60°) Double-sided chipbreaker for improved chip control Targeted use: face, shoulder, slot, high-feed and contour milling Designed for Tungaloy milling systems; seat and body must match technically FAQ What materials is this insert designed to machine? The SNMU1307AN AH3135 insert is a PVD-coated carbide grade formulated for general milling applications where wear resistance and a sharp cutting edge are required; it suits a broad range of common milling materials when paired with the correct cutter body. How does the chipbreaker affect machining? The insert’s double-sided chipbreaker promotes predictable chip formation and evacuation, reducing heat concentration and improving surface quality during both roughing and finishing passes. Is the insert compatible with any milling body? Compatibility requires that the insert seat, geometry and the milling body match technically; the SNMU1307AN design is intended for use within Tungaloy milling systems that accept the SNMU form and 1307AN ISO variant. What clamping features ensure reliable fixation? A central cylindrical hole plus double-sided countersink (40°–60°) provides secure mechanical clamping and precise positioning in the cutter head, supporting consistent torque transfer and stable cutting. Can the insert be indexed to use both sides? Yes, the square, double-sided design permits indexing to fresh edges, effectively doubling the number of usable cutting edges and extending overall tool economy. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
SNMU 1307AN AH3225 Wendeplatten - Tungaloy
Benefit from the wear-resistant AH3225 PVD coating paired with a robust carbide substrate and a 90° square geometry for consistent, process-secure milling. Order the SNMU 1307AN AH3225 insert directly via Metav Werkzeuge or contact our consultants for application guidance. SNMU 1307AN AH3225 SNMU — Tungaloy milling insert, 90° square, PVD-coated carbide SNMU 1307AN AH3225 is a PVD-coated carbide indexable insert engineered for versatile milling operations in compatible Tungaloy systems PVD-coated carbide grade AH3225 Square 13 mm insert with 90° cutting angle Double-sided chipbreaker for stable chips Cylindrical hole with double countersink 40°–60° Consistent edge life for uninterrupted production The combination of PVD-coated surface and a cemented carbide substrate delivers enhanced wear resistance and controlled crater formation, which translates into longer tool life and fewer index changes. For milling operations that demand repeatability, the wear behaviour of the AH3225 grade reduces downtime and stabilises process windows, allowing for predictable tool-change intervals and lower overall machining costs. Reliable chip control to protect the tool and workpiece A double-sided chipbreaker and square geometry ensure consistent chip formation across face, shoulder and slot milling. Stable chips lower the risk of workpiece damage and reduce the load on coolant and chip evacuation systems. This results in improved surface integrity and fewer interruptions during high-feed or contour passes, supporting higher productive throughput without compromising component quality. Designed for straightforward integration into Tungaloy systems The insert features a cylindrical hole with a double-sided countersink (40°–60°) and a defined seat geometry, so the insert, cutter body and clamping screw must match technically for safe operation. When assembled correctly into the corresponding milling body, the system yields secure clamping and consistent positioning, which are essential for tight tolerance machining and repeatable results. Versatile performance across common milling tasks This indexable plate is suitable for face, shoulder, slot, high-feed and contour milling depending on the assigned cutter family. With a 13 mm inscribed size and a 7.94 mm plate thickness, the geometry supports both roughing and finishing strategies while the 90° cutting angle helps maintain rigidity in axial and radial engagement—benefits that contribute to reliable dimensional control and surface finish in a range of materials. For process-critical milling with genuine Tungaloy inserts, contact Metav Werkzeuge for application advice or to secure the SNMU 1307AN AH3225 — email info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: 6823979 Manufacturer SKU: TUN6823979 SKU: 6823979-Tungaloy Model series: Indexable milling inserts Material: cemented carbide Core data Inscribed circle / size: 13 mm Plate thickness: 7.94 mm Corner radius: 0 mm Relief angle: 0° Cutting angle: 90° Hole: with hole Hole style: cylindrical hole + double-sided countersink (40°–60°) Special features Coating: PVD-coated, grade AH3225 Chip control: double-sided chipbreaker Shape: square insert Typical applications: face, shoulder, slot, high-feed and contour milling System composition: milling body, indexable insert, clamping screw, possible underlay Notes: plate seat, geometry and cutter body must be technically compatible FAQ What materials can this insert machine effectively? The SNMU 1307AN AH3225 insert in PVD-coated cemented carbide is designed for a wide material spectrum; the grade focuses on wear resistance and process security for typical steel and alloy applications used in milling. Is the insert reversible or single-use per side? The SNMU 1307AN AH3225 is double-sided, allowing both sides to be utilised where the cutter and seat permit, which improves economy per insert when applied under appropriate cutting parameters. Which cutter bodies are compatible with this insert? Compatibility requires matching seat geometry and clamping method; the SNMU 1307AN AH3225 is intended for Tungaloy milling systems where the plate seat, geometry and milling body are specified for this ISO designation. Does the insert include a chipbreaker suitable for high-feed operations? Yes, the double-sided chipbreaker supports stable chip formation and is suitable for a range of milling strategies, including high-feed and contour machining when used in the correct cutter family. What is the significance of the 40°–60° countersink? The double-sided countersink (40°–60°) around the hole ensures reliable clamping and alignment in the milling body, improving stability and repeatability of the cutting edge position. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
SNMU 1307AN T1215 Wendeplatten - Tungaloy
Take advantage of Tungaloy's balanced T1215 carbide grade and the secure clamping provided by the cylindrical hole with double-sided countersink for reliable milling performance. The square 13 mm insert with a double-sided chipbreaker and 90° geometry delivers consistent chip control and predictable tool life; order directly via Metav Werkzeuge or contact our consultants for application support. SNMU 1307AN T1215 – SNMU milling indexable insert, square 13 mm, Tungaloy The SNMU1307AN is a square, double-sided carbide indexable insert for milling, designed for use in Tungaloy milling systems where the seat, geometry and cutter body are technically matched Tungaloy grade T1215 for balanced wear resistance Square 13 mm insert, 7.94 mm thickness Double-sided chipbreaker for reliable chip control Cylindrical hole with double countersink (40°–60°) Consistent cutting performance through material and coating design The insert is produced in Tungaloy's T1215 carbide grade, which balances wear resistance and toughness to suit a wide range of milling tasks. This composition supports a stable cutting edge under intermittent loads and high material removal rates; the result is more consistent cycle times and fewer unexpected tool changes. The presence of a double-sided chipbreaker improves chip formation and evacuation, reducing the risk of re-cutting and helping to maintain surface integrity on the workpiece. Compatibility with the matching tool body ensures that the mechanical clamping forces are transmitted correctly, preserving both insert life and process stability. Secure clamping and geometry that enable versatile milling applications The square geometry and 13 mm inscribed circle, combined with a 7.94 mm plate thickness, provide a robust platform for shoulder, slot and contour milling. A cylindrical hole with a double-sided countersink (40°–60°) ensures positive seating and repeatable location in the cutter pocket; this reduces micro-movements that can accelerate wear. The 90° included angle is suitable for shoulder milling and general-purpose operations, and the symmetrical, indexable layout supports economical edge use. Where high-feed or special cutter families are involved, the insert's defined form allows simple matching to the correct cutter body and clamping screw for secure assembly. Process benefits: efficiency, predictability and easier tool management Using an indexable insert in this design simplifies tool inventory and shortens downtime: worn edges are rotated or replaced instead of regrinding solid tools. The combination of carbide substrate and the chip control geometry enhances edge stability, which translates into fewer rejects and a reduced need for mid-process inspection. For production environments seeking repeatable results, the insertion design supports stable chip flow and consistent surface quality, while the requirement that seat, geometry and cutter body match provides a clear technical boundary to avoid misfitting. For application queries or help selecting the correct cutter family, Metav Werkzeuge can provide tailored technical advice. For reliable high-output milling with Tungaloy's T1215 inserts, contact Metav Werkzeuge for tailored advice or to arrange supply of the SNMU1307AN—email info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: 6758742 SKU: 6758742-Tungaloy Manufacturer SKU: TUN6758742 Model series: Milling indexable inserts Label: SNMU1307AN T1215 Tungaloy indexable insert Material: carbide Core technical data Plate thickness: 7.94 mm Plate size (inscribed): 13 mm Corner radius: 0 Free angle: 0° Included angle: 90° Hole style: cylindrical hole + double-sided countersink (40°–60°) Design and features Square plate form, double-sided indexable design Double-sided chipbreaker With hole for secure clamping Tungaloy grade T1215 Intended use: milling (plan, shoulder, slot, high-feed, contour depending on tool family) System components: cutter body, indexable insert, clamping screw, possible shim Requires matching seat, geometry and cutter body for correct assembly FAQ Which milling operations is this insert suitable for? The SNMU1307AN T1215 insert is designed for plan, shoulder, slot, high-feed and contour milling depending on the assigned tool family and cutter body. What are the key dimensions of the insert? The insert has a 13 mm inscribed circle, a plate thickness of 7.94 mm, a corner radius of 0 and an included angle of 90° for the SNMU1307AN. How is the insert secured in the cutter body? The SNMU1307AN is secured via a cylindrical hole with a double-sided countersink (40°–60°) and requires a matching seat, correct geometry and clamping screw for repeatable fixing. Is the insert indexable and reversible? Yes; the double-sided chipbreaker and square form allow the insert to be indexed and used on more than one cutting edge in accordance with the holder design. Is this an original Tungaloy product? Yes, this is an original Tungaloy indexable insert, manufacturer article number 6758742 and SKU 6758742-Tungaloy. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
SNMU 1307AN T3225 Wendeplatten - Tungaloy
Take advantage of the combination of Tungaloy's T3225 cutting grade, a robust carbide body and a square 13 mm form for stable, high-productivity milling; ensure the insert seat and cutter body match technically for safe operation. Order directly via Metav Werkzeuge or consult the technical team for application matching. SNMU 1307AN T3225 — Indexable milling insert for Tungaloy systems (Tungaloy) The SNMU1307AN T3225 is a square, hole-mounted indexable insert designed for milling tasks within Tungaloy milling systems, delivering a balance of wear resistance and cutting-edge stability for face, shoulder, slot and contour operations. Square 13 mm insert for versatile milling Tungaloy T3225 grade for wear resistance Carbide body with double-sided chipbreaker Cylindrical hole with 40°–60° countersink Reliable cutting performance that raises productivity The insert delivers a predictable tool life thanks to the T3225 grade, which balances wear resistance and toughness to withstand interrupted cuts and variable feed conditions. The robust carbide composition supports sustained cutting forces and helps reduce downtime caused by premature wear. For engineers seeking consistent component quality, the stable cutting edge provided by this plate reduces the frequency of insert changes and contributes to a smoother production flow. Compatibility between the insert seat, geometry and cutter body is essential; mismatches will negate the plate’s performance benefits. Simple system integration and predictable chip control Designed as part of a complete system, the insert works together with the cutter body, clamping screw and, if required, a backing pad to form a secure assembly. The double-sided chipbreaker geometry supports reliable chip formation across a range of milling strategies, improving evacuation and protecting the cutting edge. The square format with a cylindrical hole plus countersink (40°–60°) facilitates repeatable clamping and indexability, enabling multiple cutting edges per plate and cost-effective utilisation of the insert’s life. Clearances and seat dimensions must match the cutter to guarantee correct clamping and repeatable concentricity. Practical benefits for varied milling operations When configured correctly, the insert supports a broad spectrum of milling tasks — from face and shoulder work to high-feed and contour milling — depending on the associated tool family. The plate’s 13 mm size and 7.94 mm thickness provide structural rigidity for higher feed rates while the 0° clearance angle and 0 corner radius are optimised for applications where a defined edge and stable cutting geometry are required. By selecting the right grade and ensuring a precise mechanical fit, manufacturers can expect improved process reliability and consistent surface finish on machined components. Contact Metav Werkzeuge for application consultation and availability of the Tungaloy SNMU1307AN T3225 insert; technicians can advise on cutter compatibility and stocking options — eMail: info@metav-werkzeuge.com — Phone: +49 2822 7131930 Technical data Article number: 6758741 SKU: 6758741-Tungaloy Manufacturer article number: TUN6758741 Model series: Fräswendeschneidplatten WPL designation: SNMU1307AN Facts Size: 13 mm Plate thickness: 7.94 mm Insert shape: square Corner radius: 0 Clearance angle: 0° Main angle: 90° Hole: with hole Countersink: 40°–60° Special features Material: carbide Grade/coating: T3225 (Tungaloy) Chipbreaker: double-sided Hole style: cylindrical hole + double-sided countersink Intended application: milling Typical uses: face milling, shoulder milling, slot milling, high-feed milling, contour milling System components: insert, clamping screw, backing pad (as required) FAQ What milling operations is this insert suited to? This insert is suitable for face, shoulder, slot, high-feed and contour milling when used in the corresponding Tungaloy cutter families and with matching plate seats. How does the T3225 grade influence performance? The T3225 grade combines wear resistance and toughness to provide a reliable cutting edge and longer usable life in interrupted and continuous milling conditions. Is the insert indexable and how many edges are usable? The square form with a central hole provides multiple indexable cutting edges; correct clamping and seat conformity ensure safe and repeatable indexing of the insert. What must be checked before fitting the insert? Ensure the insert seat, geometry and cutter body are technically compatible; correct seating, torque on the clamping screw and the specified backing pad (if required) are necessary for secure assembly and concentric cutting. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
SNMU 1706AN AH120 Wendeplatten - Tungaloy
Take advantage of the wear-resistant AH120 grade and precise 90° square geometry to secure stable, predictable milling results; order the SNMU 1706AN AH120 from Metav Werkzeuge or consult their specialists for application-specific guidance. SNMU 1706AN AH120 — Tungaloy milling indexable insert for general milling The SNMU 1706AN AH120 is a square, PVD-coated carbide indexable insert conceived for milling tasks such as face, shoulder, slot, high-feed and contour operations within compatible Tungaloy milling systems. PVD-coated carbide grade AH120 for wear resistance Square 90° insert, 17 mm size, 6.35 mm thickness Central hole with cylindrical bore and countersink Double-sided chipbreaker for reliable chip control Reliable cutting performance that extends tool life The PVD-coated AH120 grade combines a tough substrate with a wear-resistant surface layer, delivering process security under demanding cutting conditions. The PVD-coated finish sustains a sharp cutting edge for longer intervals, which reduces edge deterioration and lowers the frequency of index changes. As a result, machining runs remain predictable and tool life is enhanced, promoting economical production and fewer unplanned stoppages. System compatibility for safe clamping and accurate geometry Designed as part of Tungaloy milling systems, this square insert requires a matching insert seat and cutter body for correct function; the central cylindrical hole with double-sided countersink (40°–60°) provides secure, concentric clamping and reliable seating under load. The 90° geometry and 17 mm size together with the 6.35 mm thickness ensure a compact yet robust cutting edge suited to a range of cutter families, helping to maintain repeatable cutting conditions and stable tool runout. Better chip control and improved surface quality The double-sided chipbreaker is engineered to produce controlled chip segmentation and evacuation, which lowers heat concentration at the cutting zone and reduces the risk of edge chipping. Improved chip control directly supports a finer surface finish and fewer secondary operations, especially in mixed-operation setups such as face and contour milling. For applications that demand a sharp edge and consistent results, the chip geometry contributes to steady cutting forces and reduced workpiece rejections. Production advantages from simplified handling and robust design A square, double-sided insert provides two usable cutting edges per index, easing inventory management and increasing effective edge count per insert. The combination of the AH120 grade and robust design supports process reliability and reduced downtime, since fewer index changes and consistent edge behaviour translate into less operator intervention. In short, the insert is a practical choice where efficient, repeatable milling and straightforward logistics are priorities. Contact Metav Werkzeuge for application-specific recommendations or to arrange a supply of Tungaloy SNMU 1706AN AH120 inserts through their technical sales team Technical data Article number: 6861796 SKU: 6861796-Tungaloy Manufacturer SKU: TUN6861796 Manufacturer: Tungaloy Model series: Fräswendeschneidplatten Dimensions & core data Insert size: 17 mm Thickness: 6.35 mm Corner radius: 0 mm Relief angle: 0° Main angle: 90° Central hole: with hole Features & coating Material: Hartmetall Coating: PVD Grade: AH120 Shape: square Hole style: cylindrical hole + double-sided countersink (40°–60°) Chipbreaker: double-sided Typical application: face, shoulder, slot, high-feed and contour milling FAQ Is this insert compatible with existing Tungaloy milling bodies? Compatibility requires matching the insert seat, geometry and cutter family; the SNMU 1706AN AH120 is intended for use in Tungaloy milling systems that accept square 17 mm, 6.35 mm thick indexable inserts. Which machining tasks suit this grade best? The AH120 grade on the SNMU 1706AN AH120 excels where a sharp cutting edge and process security are required, for example in face, shoulder and high-feed milling operations. What benefit does the double-sided chipbreaker provide? The double-sided chipbreaker on this Tungaloy indexable insert improves chip segmentation and evacuation, which reduces heat at the cutting edge and helps achieve a more consistent surface finish. How does the insert clamping work? Clamping relies on the central cylindrical hole combined with the double-sided countersink (40°–60°) to ensure secure axial and radial seating, supporting stable cutting under varying loads. What are the key dimensions and identifiers for ordering? Key dimensions: 17 mm size, 6.35 mm thickness, 90° geometry, 0 mm corner radius; ordering identifiers include Article number 6861796 and SKU 6861796-Tungaloy. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
SNMU 1706AN AH140 Wendeplatten - Tungaloy
Take advantage of the combination of a PVD-coated AH140 carbide grade, a square 17 mm form with 90° geometry, and a double-sided chipbreaker for predictable chip control and extended tool life; order original Tungaloy inserts via Metav Werkzeuge or request application advice from our consultants. SNMU1706AN AH140 Milling Insert for Milling – Tungaloy A SNMU1706AN AH140 insert designed for compatible Tungaloy milling systems, offering a sharp cutting edge and secure performance across face, shoulder, slot, high-feed and contour milling applications. PVD-coated carbide AH140 for wear resistance Sharp cutting edge for process security Square 17 mm form with 90° geometry Cylindrical hole with 40°–60° double countersink Consistent milling performance through hardened carbide and coating The SNMU1706AN AH140 is manufactured from carbide and finished with a PVD coating, which together deliver high abrasion resistance and a stable cutting edge. This combination reduces flank wear and helps maintain dimensional accuracy over longer tool lives. For production environments where cycle stability matters, the AH140 grade supports a balance between edge strength and wear resistance, making the insert suitable for demanding, repetitive milling tasks while reducing unplanned tool changes. Secure seating and predictable chip control for efficient machining Designed for inserts with a matching seat and geometry in the milling body, the square form and cylindrical hole with double-sided countersink (40°–60°) ensure secure clamping and axial positioning. The double-sided chipbreaker promotes consistent chip formation and evacuation, lowering the risk of built-up edge and workpiece damage. Together, these features contribute to shorter setup times and more reliable throughput in batch or continuous milling operations. Optimised for process reliability and sharp-edge performance The zero corner radius and sharp cutting edge of this insert provide clean entry and exit during shoulder and contour passes, improving surface finish and reducing burr formation. The 90° cutting angle supports robust cutting forces for face and slot milling, while the 6.35 mm plate thickness gives stable support under higher feeds. Such design choices aim to reduce vibration and support repeatable part quality, important when consistency and first-pass yield are priorities. Versatile application range with clear integration requirements This insert suits a wide range of milling tasks—face, shoulder, slot, high-feed and contour milling—provided that the insert seat, geometry and cutter body are technically compatible with the system. The insert’s specifications, including square 17 mm form, 6.35 mm thickness and the SNMU1706AN ISO designation, should be verified against the chosen milling body to ensure correct fit and clamping. Where a sharp cutting edge combined with process security is required, this AH140 grade offers a dependable solution without sacrificing robustness. Contact Metav Werkzeuge for tailored application advice and to obtain original Tungaloy SNMU1706AN AH140 inserts; call +49 2822 7131930 or email info@metav-werkzeuge.com Technical data Article number: 6861815 SKU: 6861815-Tungaloy Manufacturer SKU: TUN6861815 Model series: Milling insert series Material: Carbide Numbers / Core technical data Size: 17 mm Thickness: 6.35 mm Cutting angle: 90° Corner radius: 0 Relief angle: 0° Designs / Special features ISO designation: 1706AN Grade: AH140 Coating: PVD-coated carbide Hole: with hole Hole style: cylindrical hole + double-sided countersink (40°–60°) Plate form: square Chipbreaker: double-sided FAQ What milling operations suit this insert? The SNMU1706AN AH140 insert is intended for face, shoulder, slot, high-feed and contour milling in compatible Tungaloy milling systems and is optimised for operations requiring a sharp cutting edge and process security. Which cutter bodies must be used with this insert? The insert requires a cutter body and seat that match the SNMU geometry and ISO designation; correct seating and clamping in the Tungaloy system ensure the designed performance of the SNMU1706AN AH140. How does the AH140 grade affect tool life? The AH140 PVD-coated carbide grade combines wear resistance with edge strength, promoting longer tool life under typical milling loads while maintaining process stability. Is the insert suitable for fine contour finishing? Yes, the sharp cutting edge and 90° geometry of the SNMU1706AN support clean contour passes, improving surface finish when used within recommended cutting parameters. What should be checked before fitting the insert? Verify seat compatibility, correct geometry, and the matching cutter body; ensuring the SNMU1706AN fits securely prevents misalignment and preserves the intended machining performance. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
SNMU 1706AN AH3135 Wendeplatten - Tungaloy
Benefit from the combination of PVD-coated carbide wear resistance, precise 17 mm square geometry and a secure clamping design for consistent milling performance; order the insert directly via Metav Werkzeuge or consult our specialists for application matching. SNMU1706AN AH3135 Tungaloy indexable insert for milling — square 17 mm, PVD-coated carbide, 90° cutting angle The SNMU1706AN AH3135 Tungaloy indexable insert offers wear- and chipping-resistant performance for a wide range of milling operations when matched to the correct cutter body and clamping system PVD-coated carbide AH3135 for milling Designed for Tungaloy milling systems Square 17 mm with 6.35 mm thickness Cylindrical hole with 40°–60° countersink Consistent cutting performance through advanced coating and grade The combination of a PVD-coated surface and a carbide substrate in grade AH3135 provides a durable cutting edge that keeps dimensions stable across long production runs. The PVD layer improves resistance to wear and heat, while the carbide core sustains edge integrity under interrupted cuts. This results in fewer tool changes and more predictable cycle times in facemilling, shoulder milling and contour operations. The material choice is particularly beneficial when a sharp cutting edge and high process reliability are required, since the coating and substrate work together to reduce abrasion and minimise chipping. Geometry and clamping ensure accurate, repeatable mounting The square 17 mm form, 6.35 mm thickness and a 90° cutting angle are engineered for exact seating in matched Tungaloy tool bodies; the insert’s cylindrical hole with double-sided countersink (40°–60°) and a double-sided chipbreaker promote secure clamping and consistent chip control. Correct seat alignment and use of the specified clamping screw and pad maintain repeatability from index to index, reducing set-up time and guaranteeing consistent component quality. For users migrating between tool families, ensuring geometric compatibility of insert seat, geometry and cutter body is essential to preserve the intended cutting geometry and avoid unexpected runout. Flexible application spectrum and machining guidance Designed for face, shoulder, slot, high-feed and contour milling depending on the assigned cutter family, the insert’s characteristics favour operations where a controlled chip formation and a reliable edge are priorities. The double-sided chipbreaker helps to regulate chip flow across various depths of cut and feed rates, improving surface finish and reducing the risk of built-up edge. For initial process set-up, conservative feed and speed values are recommended until cutting stability is verified; further optimisation can then focus on cycle-time reduction and tool-life extension. Technical consultation is available for selecting ideal parameters for specific materials and component geometries. Contact Metav Werkzeuge for application matching and to secure genuine Tungaloy SNMU1706AN AH3135 inserts — email info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: 6727291 SKU: 6727291-Tungaloy Manufacturer SKU: TUN6727291 Model series: Fräswendeschneidplatten Material: Hartmetall Grade / coating: AH3135, PVD-coated Core dimensions Size: 17 mm Thickness: 6.35 mm Corner radius: 0 Relief angle: 0° Cutting angle: 90° Hole style: cylindrical hole + double-sided countersink (40°–60°) Special features Double-sided chipbreaker Square insert form Designed for Tungaloy milling systems Requires matching insert seat, clamping screw and possibly pad Wear- and chipping-resistant grade for stable cutting FAQ What milling operations suit this insert best? The SNMU1706AN AH3135 Tungaloy indexable insert is intended for face, shoulder, slot, high-feed and contour milling depending on the associated cutter family; selection should follow the cutter body’s application guidelines. How does the AH3135 grade affect performance? AH3135 is a PVD-coated carbide grade engineered for wear and chipping resistance; the coating enhances heat and abrasion resistance while the carbide substrate preserves edge strength for reliable milling performance. Is special clamping required for this insert? The insert requires a compatible Tungaloy milling body with the correct insert seat and a clamping screw (and pad if specified) to ensure secure mounting; the cylindrical hole with countersink supports stable clamping. Can the insert be re-indexed after wear? The double-sided square design permits re-indexing according to the cutter family’s specifications; check the cutter body documentation to confirm the number of usable edges and indexing procedure. What information is needed to match this insert to a cutter body? Provide the insert designation (SNMU1706AN), grade (AH3135), dimensions (17 mm × 6.35 mm), hole / countersink style and the cutter family so that compatibility and correct seating can be verified. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
SNMU 1706AN AH3135 Wendeplatten - Tungaloy
Take advantage of the AH3135 PVD-coated carbide grade and the robust square geometry for reliable milling performance; the combination of double-sided chipbreakers and a central hole with countersink ensures secure clamping and consistent chip control. Order the Tungaloy inserts or contact Metav Werkzeuge’s consultants for application support and delivery. SNMU 1706AN AH3135 indexable insert for milling by Tungaloy SNMU1706AN AH3135 Tungaloy indexable insert is designed for precision milling applications and suitable for face, shoulder, slot, high-feed and contour milling when used in matching Tungaloy milling bodies. SNMU1706AN compatible with Tungaloy milling systems AH3135 PVD-coated carbide for wear resistance Double-sided chipbreaker for reliable chip control Square 17 mm insert with central hole and countersink Longer edge life through optimised grade and coating The PVD-coated AH3135 grade combines a wear-resistant surface with a tough substrate to extend edge life under mixed cutting conditions. This PVD-coated finish reduces adhesive wear and improves flank life, which translates into longer tool cycles and fewer indexings. For production environments where process stability matters, the coated carbide composition delivers consistent performance, reducing unplanned downtime and maintaining surface quality over extended runs. Secure clamping and stable cutting geometry for repeatable results A square insert with a central hole and a cylindrical hole plus double-sided countersink (40°–60°) provides a reliable mechanical interface with compatible milling bodies. The 90° cutting angle and the specified relief geometry ensure predictable engagement and even load distribution during heavy shoulder or face milling. Because the seat, geometry and cutter body must match technically, this arrangement supports repeatable positioning and reduces the risk of micro-movement that can affect tolerances and surface finish. Improved chip control and process security with double-sided breakers The double-sided chipbreaker design offers controlled fragmentation and evacuation of chips across a range of feeds and depths. Smart chip formation reduces re-cutting, minimises heat concentration at the cutting edge and lowers tool load peaks — all contributing to process security and consistent component quality. For applications demanding a sharp cutting edge and stable operation, the chipbreaker geometry is a decisive advantage when combined with the AH3135 grade. Dimensions and form factor that suit modular milling systems Manufactured in a square 17 mm size with a 6.35 mm plate thickness and a 0 mm corner radius, the insert is optimised for applications where a defined edge and rigid clamping are required. The double-sided design effectively offers multiple usable faces, enabling economical indexing strategies. When integrated into a matched Tungaloy cutter body, the insert’s geometry supports precise cutting forces and helps maintain repeatable surface integrity across serial production. Speak to Metav Werkzeuge for tailored selection and cutting data for Tungaloy AH3135 inserts to integrate them into production and ensure optimum process parameters Technical data Article number: 6727292 Manufacturer SKU: TUN6727292 SKU: 6727292-Tungaloy Model series: Fräswendeschneidplatten (milling indexable inserts) Facts Insert designation: SNMU1706AN Grade: AH3135 Shape: square, 17 mm Thickness: 6.35 mm Cutting angle: 90° Corner radius: 0 mm Relief angle: 0° Hole style: cylindrical hole + double-sided countersink (40°–60°) Special features Material: carbide (PVD-coated where specified) Double-sided chipbreaker Central hole for secure clamping Designed for face, shoulder, slot, high-feed and contour milling Compatible with Tungaloy milling systems when seat geometry matches FAQ What milling tasks are suitable for this insert? The SNMU1706AN AH3135 Tungaloy insert is intended for face, shoulder, slot, high-feed and contour milling when used with matching Tungaloy cutter bodies and clamping systems. Is this insert designed for stable process conditions? Yes. The AH3135 grade and the double-sided chipbreaker of the SNMU1706AN insert support process security and a sharp cutting edge under varying milling conditions. How is the insert fixed in the cutter body? The insert features a central cylindrical hole with a double-sided countersink (40°–60°) to accommodate a clamping screw and ensure secure seating in the corresponding Tungaloy milling body. Does the design allow indexing of cutting edges? The square, double-sided construction permits indexing to fresh faces; the geometry is intended for economical edge changes while maintaining stability. What are the key dimensional details to check before ordering? Verify the 17 mm square form, 6.35 mm thickness, 90° angle, 0 mm corner radius and the central hole plus countersink to ensure compatibility with the selected milling cutter. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
SNMU 1706AN AH725 Wendeplatten - Tungaloy
Take advantage of the combination of a PVD-coated AH725 carbide grade, robust square geometry and precise mounting detail for reliable milling performance; order the insert directly via Metav Werkzeuge or consult the technical team for application matching. SNMU 1706AN AH725 Tungaloy milling insert — PVD carbide, square 17 mm SNMU1706AN AH725 is a square indexable insert designed for Tungaloy milling systems, intended for face, shoulder, slot, high-feed and contour milling where compatibility with the cutter body is required. PVD-coated universal grade AH725 Square plate 17 mm Double-sided chipbreaker Cylindrical hole with countersink 6.35 mm plate thickness Optimised grade for mixed steel applications and process security The AH725 grade is a PVD-coated carbide developed as a universal, breakage‑resistant option for machining steel and stainless steels. The coating provides a thin, hard surface layer that reduces adhesive wear and enhances thermal stability; in practical terms this translates into steadier cutting performance and fewer unplanned tool changes. For shops facing rapidly changing batch compositions or smaller cutter bodies, the grade offers predictable tool life and higher process security, which supports stable cycle times and reduces scrap rates. Geometry and clamping designed for secure engagement and chip control The square form and the plate’s double-sided chipbreaker direct swarf away from the cutting zone and assist consistent cutting forces during interrupted cuts. A cylindrical hole with a double-sided countersink (40°–60°) ensures positive seating in compatible milling bodies while the 6.35 mm plate thickness contributes to rigidity under load. The specified 90° approach angle is suitable for general-purpose shoulder and face milling. Note that correct mating between insert seat, geometry and cutter body is essential for safe, repeatable performance; the insert is intended for use only with matching Tungaloy milling bodies. Versatile use across common milling operations The insert is suitable for a wide range of milling tasks — from finishing contours to higher-feed face and shoulder milling — depending on the selected cutter family. Its universal character reduces the number of grades required in inventory when processing mixed batches, improving setup speed and stock efficiency. The PVD layer helps maintain a sharp cutting edge at elevated temperatures, while the chipbreaker geometry promotes stable swarf behaviour; the result is better surface finish consistency and fewer secondary operations in many workflows. Practical notes for integration and handling When fitting the insert into a milling body, ensure the seat and geometry match the specified indexable system: clamping screw, insert seat and any backing shim must be compatible. The plate’s square shape and hole/countersink detail require the appropriate clamping torque and seat condition for repeatable outcomes. Where toolpaths include repeated entry and exit, the breakage‑resistant nature of the grade supports higher reliability and lowers the risk of sudden corner failure, contributing to predictable production runs. Contact Metav Werkzeuge for application advice, compatibility checks or to place an order for genuine Tungaloy SNMU1706AN AH725 inserts — technical consultants are available to ensure the insert suits the intended milling body and operating parameters. Technical Data Article number: 6861801 SKU: 6861801-Tungaloy Manufacturer SKU: TUN6861801 Model series: Fräswendeschneidplatten Material: Hartmetall Data Plate size: 17 mm Plate thickness: 6.35 mm Angle: 90° Corner radius: 0 mm Hole: with hole Hole style: cylindrical hole + double-sided countersink (40°–60°) Special features Grade/coating: AH725, PVD-coated carbide Plate form: square Chipbreaker: double-sided Typical applications: face, shoulder, slot, high-feed and contour milling Compatibility note: insert seat, geometry and milling body must match technically FAQ What materials is this insert intended for? The SNMU1706AN AH725 insert is specified for machining steel and stainless steels and is suitable where a universal, breakage‑resistant grade is required. How does the AH725 coating improve performance? The PVD coating on the AH725 grade increases surface hardness and thermal resistance, which helps maintain edge stability and improves wear resistance during continuous milling. Is the insert compatible with any milling body? The insert requires a matching Tungaloy milling body with the correct seat and clamping arrangement; proper mating of seat, geometry and clamping components is essential for safe use. What chip control can be expected with this plate? The double-sided chipbreaker is designed to promote consistent swarf formation and evacuation, improving surface finish stability and reducing the risk of recutting. Are there any special mounting requirements? Ensure the clamping screw, backing shim (if applicable) and seat are in good condition and tightened to the recommended torque for the intended milling body to achieve repeatable corrosion‑free seating. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
Fragen zu diesen Produkten??
Mit mehr als 30 Jahren Erfahrung beraten wir Sie gerne persönlich.
Tel.: +49 2822 7131930
Mail: info@metav-werkzeuge.com