TCMT 110308 T6215 Wendeplatten - Tungaloy
Take advantage of the combination of wear-resistant CVD-coated carbide, precise geometry and ISO compatibility for consistent performance in turning stainless steels; order or request guidance through Metav Werkzeuge for reliable supply and application support. TCMT 110308 T6215 triangular turning insert by Tungaloy — ISO-compatible carbide for stainless steels TCMT110308 T6215 is a triangular insert designed for ISO-standard turning applications, optimised for external and internal machining of stainless steels under stable to lightly interrupted cutting conditions. ISO-standard triangular insert CVD-coated carbide grade T6215 Suited for turning stainless steels Cylindrical hole + single-side countersink High-performance coating and material for extended service life The insert is made from CVD-coated carbide, a coating process that deposits a hard ceramic layer to improve wear resistance and reduce built-up edge during machining. As part of an ISO insert series, this solution provides consistent tool life and predictable replacement cycles, which supports planning in production environments. The combination of the carbide substrate and coating is particularly effective when machining stainless steels, where adhesion and abrasion are typical wear modes. Geometry engineered for strength and surface quality The triangular geometry with a 60° included angle and a 0.8 mm corner radius balances cutting-edge strength and surface finish. A 7° relief angle reduces rubbing on the flank while maintaining an effective cutting edge, and the 3.18 mm thickness contributes to rigidity in the clamping system. The insert’s cylindrical hole with a single-side countersink (40°–60°) enables secure indexing in compatible holders; selection of the appropriate chipbreaker and clamping ensures optimal chip control and process stability. Process benefits: stability, productivity and reduced downtime Designed for turning, the plate’s features promote process stability by resisting wear in continuous and slightly interrupted cuts. The CVD coating helps to lower cutting temperatures and maintain edge integrity, which translates into improved surface finish and fewer tool changes. For production, this means higher mean time between interventions and a clearer cost-per-part calculation, supporting decisions that favour productivity and predictable output. Compatibility and system considerations for straightforward integration The insert is ISO-compatible and intended to be used with corresponding triangular insert holders, clamping sets and replacement screws to form a complete turning system. Its design supports both external and internal turning operations; proper matching of holder form, free angle, tolerance class, fastening method, size and thickness is essential for safe and repeatable performance. The carbide grade T6215 is tailored for machining stainless steels under stable to lightly interrupted conditions, offering a balance between wear resistance and toughness. For tailored advice on selecting the right TCMT 110308 T6215 insert for specific stainless steel turning tasks or to confirm availability with Metav Werkzeuge, contact info@metav-werkzeuge.com or call +49 2822 7131930 for a prompt recommendation and supply details. Technical data Article number: 6903126 Manufacturer SKU: TUN6903126 Manufacturer designation: TCMT110308 T6215 Material: carbide Facts Shape: triangular Included angle: 60° Relief angle: 7° Corner radius: 0.8 mm Thickness: 3.18 mm Special features Grade: T6215, CVD-coated carbide Hole: cylindrical + single-side countersink (40°–60°) Application: external and internal turning System: ISO indexable insert compatible FAQ What materials is this insert suited for? The TCMT 110308 T6215 insert is optimised for machining stainless steels; the CVD coating and carbide substrate improve wear resistance when turning such alloys. Which holder characteristics must be matched? Compatibility requires matching holder form, free angle, tolerance class, fastening type, size and thickness; ISO-compatible triangular holders designed for TCMT inserts are appropriate. What does the grade T6215 indicate? T6215 denotes a CVD-coated carbide grade engineered for wear resistance and stability in turning stainless steels, offering a balance between edge life and toughness. How does the 0.8 mm corner radius affect machining? A 0.8 mm corner radius increases edge strength and helps absorb vibration in heavier cuts while offering good general-purpose surface finish; smaller radii would favour finer finishes but reduce edge robustness. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
TCMT 110308 T6215 Wendeplatten - Tungaloy
Take advantage of the combination of CVD-coated carbide durability, a 0.8 mm corner radius for reliable edge strength and ISO compatibility for easy toolholder matching to maintain steady turning production; order the insert directly via Metav Werkzeuge or contact the consultants for application advice. TCMT 110308 T6215 TCMT — ISO triangular turning insert by Tungaloy for turning The TCMT 110308 T6215 is an ISO-standard triangular turning insert optimised for machining rostfreier Stahl under stable to mildly interrupted cutting conditions. ISO triangular insert TCMT 110308, T6215 grade CVD-coated carbide for wear resistance 0.8 mm corner radius for robust finish Cylindrical hole with single-sided countersink Increased process uptime through wear‑resistant grade and coating The T6215 grade, realised as a CVD-coated carbide, offers a wear-resistant substrate that prolongs edge life when machining rostfreier Stahl, reducing changeover frequency and improving throughput. This wear resistance delivers a predictable tool life and helps secure a consistent surface finish on external and internal turning operations. The one-sided chipbreaker supports predictable chip formation in steady conditions, helping to avoid unexpected interruptions and maintain cycle-time stability. Secure clamping and clear geometric data for reliable set-ups Compatibility follows ISO norms: shape, 7° clearance angle, tolerance class, fastening, size and 3.18 mm thickness determine correct assembly with holders. The triangular form with an 11 mm inscribed circle and a 0.8 mm corner radius gives a balance of edge strength and accessibility for finishing passes. The insert’s cylindrical hole with a single-sided countersink (40°–60°) ensures reproducible seating and torque transmission, reducing the risk of micro‑movement during cuts and improving dimensional accuracy on workpieces. Practical system view and selection guidance for efficient machining The cutting system comprises the ISO insert together with a matching outer holder or boring bar, shim/clamp set and spare screws, allowing straightforward replacement in busy production environments. Choose the chipbreaker and grade according to workpiece material, operation type and machine stability; for unstable cuts, select more robust cutterbody support and machining parameters to safeguard the edge. Clear labelling and ISO conformity simplify inventory and reordering, supporting reliable process planning and quicker tool change routines. For reliable turning of rostfreier Stahl with Tungaloy quality, contact Metav Werkzeuge for technical matching and secure supply — eMail: info@metav-werkzeuge.com • Tel: +49 2822 7131930 Technical data Article number: 6951458 SKU: 6951458-Tungaloy Manufacturer SKU: TUN6951458 Model series: ISO turning inserts Facts Corner radius: 0.8 mm Size (inscribed circle): 11 mm Thickness: 3.18 mm Clearance angle: 7° Hole style: cylindrical hole + single-sided countersink (40°–60°) Special features Grade: T6215 Coating: CVD-coated carbide Chipbreaker: one-sided Shape: triangular Application: turning (external and internal) System components: ISO insert, matching outer holder or boring bar, shim/clamp set, spare screws FAQ What materials is this insert intended for? The TCMT 110308 T6215 insert is specified for machining rostfreier Stahl and provides improved wear resistance under stable to lightly interrupted cutting conditions. How is compatibility with a toolholder determined? Compatibility depends on shape, clearance angle, tolerance class, fastening type, size and thickness; these parameters ensure the insert seats correctly and performs as intended. What does the chipbreaker offer in practice? The one-sided chipbreaker promotes controlled chip formation in steady turning operations, supporting chip evacuation and helping to maintain a consistent surface finish. Which components form the complete cutting system? A complete system comprises the ISO insert, a matching outer holder or boring bar, a shim/clamp set and spare screws, enabling reliable mounting and quick replacement. Is the grade suitable for light interruptions and continuous cuts? The T6215 grade is designed as a wear-resistant option that performs well in stable and mildly interrupted conditions typical of many turning tasks. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
TCMT 110308 T6215 Wendeplatten - Tungaloy
Take advantage of the combination of CVD-coated carbide grade T6215, a precise 0.8 mm nose radius and ISO compatibility to maintain stable turning operations with reduced tool change times; order directly via Metav Werkzeuge or consult the technical team for application matching. TCMT 110308 T6215 ISO triangular turning insert, CVD-coated for stainless steel — Tungaloy A TCMT 110308 T6215 ISO-standard triangular insert engineered for external and internal turning of stainless steel, optimised for stable to lightly interrupted cutting conditions. CVD-coated carbide grade T6215 Designed for machining stainless steel ISO TCMT 110308 triangular insert, 11 mm 7° clearance angle with cylindrical hole and countersink Reliable wear resistance for prolonged tool life The CVD-coated carbide substrate (grade T6215) delivers high wear resistance under continuous cutting, which translates into longer tool life and fewer indexings. The coating reduces abrasive wear and heat-related damage during sustained cuts; this is particularly beneficial when consistent component quality and fewer machine stops are required. Reliability in the cutting edge supports more predictable process planning and less frequent tool replacement. Consistent surface quality when machining stainless steels Stainless steels tend to work-harden and demand a stable cutting geometry to avoid built-up edge and rough finishes. The insert’s positive geometry and the 0.8 mm nose radius are designed to balance cutting forces and surface integrity. As a result, improved surface finish and dimensional consistency are achieved with reduced tendency for material adhesion on the cutting edge, which benefits subsequent operations and inspection criteria. Secure fit and ISO compatibility for fast tool changes Compatibility with tool holders is determined by form, clearance angle, tolerance class, fixing method, size and thickness; the ISO designation ensures interchangeability in standard tool systems. The insert is supplied within a common ISO system that permits rapid replacement in compatible external holders or boring bars, while the cylindrical hole with a one-sided countersink provides reliable clamping and repeatable seating to reduce setup time and variability. Controlled chip formation for safer, predictable machining The insert features a single-sided chipbreaker engineered for stainless-steel cutting conditions, encouraging short, controllable chip shapes under recommended cutting parameters. Controlled chips lower the risk of entanglement and facilitate automated chip evacuation, contributing to safer shop-floor conditions and reduced manual intervention. This controlled behaviour supports higher spindle utilisation and steadier cycle times. Geometry and dimensions optimised for versatile turning tasks With an 11 mm size, 3.18 mm thickness and the specified clearance and included angles, the triangular form offers three usable cutting edges per index, improving cost-efficiency per insert. The geometry is suitable for both external profiling and internal operations when paired with the appropriate holder. The mechanical design ensures stable seating and effective force transmission for light to moderate interrupted cuts. Guidance on selection and process setup Select the chipbreaker and grade to match workpiece material, machining strategy and machine stability; for stainless steels, favour parameter sets that limit heat concentration and avoid excessive feed spikes. The cutting system comprises the insert, a corresponding external holder or boring bar, an underlay/clamping set and replacement screws, all of which should be checked for correct tolerance and seating before production runs. For complex or demanding parts, consider a trial cut under monitored conditions to validate cutting data and expected tool life. Contact Metav Werkzeuge for precise application advice, sample availability and order processing for the Tungaloy TCMT 110308 T6215 insert; email info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: 6951424 Manufacturer SKU: TUN6951424 SKU: 6951424-Tungaloy Core specifications Size: 11 mm Thickness: 3.18 mm Nose radius: 0.8 mm Clearance angle: 7° Included angle: 60° Hole: with hole Hole style: cylindrical hole + one-sided countersink (40°–60°) Features & applications CVD-coated carbide (T6215) Single-sided chipbreaker For turning of stainless steel ISO triangular insert (TCMT 110308) System: insert, external holder or boring bar, underlay/clamping set, spare screws Triangular plate form Suitable for external and internal turning FAQ What materials is this insert recommended for? The insert is tailored for machining stainless steel; the T6215 CVD-coated carbide grade is optimised for wear resistance in such applications. How does the ISO designation affect replacement in tool systems? ISO designation TCMT 110308 ensures dimensional compatibility with ISO-standard holders, enabling fast replacement and predictable seating in established tool systems. What clamping features does the insert offer for stability? The insert has a cylindrical hole with a one-sided countersink (40°–60°) to allow secure clamping and repeatable positioning in the tool holder. Is this insert suitable for interrupted cuts? Yes — the grade and chipbreaker are designed for stable to lightly interrupted conditions; for heavy interruptions, holder rigidity and cutting data should be assessed. How many cutting edges are available per insert? The triangular shape provides three indexed cutting edges per insert, improving utilisation and cost-efficiency. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
TCMT 110308 T9215 Wendeplatten - Tungaloy
Take advantage of the high wear resistance and toughness of the CVD-coated carbide grade T9215 combined with a 0.8 mm corner radius and a 7° clearance angle for reliable, productive turning cycles. Order the TCMT110308 T9215 Tungaloy insert directly via Metav Werkzeuge or ask the consultants if further matching to holders is required. TCMT 110308 T9215 Indexable Turning Insert by Tungaloy The TCMT110308 T9215 is an ISO triangular indexable insert for turning, engineered to deliver balanced wear resistance and fracture toughness for medium steel machining. CVD-coated carbide for high wear resistance Optimised for medium steel machining 7° clearance angle for stable cutting Compatible with ISO toolholders Faster, more predictable results on medium steels The CVD-coated carbide grade T9215 combines wear resistance with shock tolerance to sustain higher material removal rates in continuous to lightly interrupted cuts. Specified as an ISO triangular insert, this grade is particularly suited to medium steel machining, where a balance between edge life and robustness reduces unscheduled tool changes and stabilises cycle times. The combination of a proven coating process and carbide substrate results in an improved cost-per-component ratio during series production without sacrificing component quality. Consistent cutting geometry for stable part quality A 60° triangular geometry with a 0.8 mm corner radius and 7° clearance angle ensures repeatable engagement and a predictable chip flow. The insert’s cylindrical mounting hole with a one-sided countersink (40°–60°) facilitates secure clamping and correct top-surface seating in many ISO toolholders, while the one-sided chipbreaker directs chips reliably for turning operations. Compatibility to the holder depends on form, clearance angle, tolerance class, fastening, size and thickness, so correct specification of the mating holder preserves the insert’s performance and repeatability. Practical features that simplify workshop routine With a plate thickness of 3.18 mm and an insert size of 11 mm, the triangular format offers several index positions for economical use of the cutting edge. The insert is delivered in the ISO model series for turning indexable inserts and is suitable for both external and internal turning when combined with a matched outer holder or boring bar. The robust geometry reduces the need for frequent edge changes, supporting uninterrupted production runs and predictable tooling costs. Reputation for reliable performance from the manufacturer further contributes to process confidence in demanding production environments. Contact Metav Werkzeuge to discuss how the Tungaloy TCMT110308 T9215 indexable insert can be matched to existing holders and machining strategies, or request further technical data via info@metav-werkzeuge.com or call +49 2822 7131930 Technical Data Article number: 6951422 Manufacturer SKU: TUN6951422 SKU: 6951422-Tungaloy Type designation: TCMT110308 Grade: T9215 Material: carbide Application: Turning Model series: ISO turning indexable inserts Facts Thickness: 3.18 mm Insert size: 11 mm Corner radius: 0.8 mm Clearance angle: 7° Insert angle: 60° Special features Coating: CVD Chipbreaker: one-sided Hole: with hole Hole style: cylindrical hole + one-sided countersink (40°–60°) Compatibility determined by form, clearance angle, tolerance class, fastening, size and thickness FAQ What materials is this insert suited for? The TCMT110308 T9215 insert is optimised for medium steel machining; the CVD-coated carbide provides a balance of wear resistance and toughness suited to continuous and lightly interrupted turning. Can the insert be used for internal and external turning? Yes, the insert is designed for both external and internal turning when used with a compatible external holder or boring bar that matches shape, clearance angle and thickness. How does the T9215 grade improve productivity? The T9215 grade offers higher wear resistance with stable edge integrity, extending tool life and allowing sustained cutting parameters for improved cycle times. What mounting features ensure secure clamping? The insert features a cylindrical hole with a one-sided countersink (40°–60°) which facilitates correct seating and secure fastening in ISO-compatible clamping systems. Which dimensions should be checked before ordering holders? Check the insert thickness (3.18 mm), insert size (11 mm), clearance angle (7°) and the 60° triangular form to ensure holder compatibility. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
TCMT 110308 T9215 Wendeplatten - Tungaloy
Take advantage of the combination of CVD-coated carbide T9215 and a 0.8 mm corner radius to achieve reliable wear resistance and fracture safety during medium-steel turning; order directly via Metav Werkzeuge or consult the technical team for application-specific advice. TCMT110308 T9215 TCMT indexable turning insert for Turning — Tungaloy A TCMT110308 T9215 indexable turning insert engineered for efficient external and internal turning of medium steels, offering high productivity in continuous to lightly interrupted cuts. CVD-coated T9215 grade for medium steel Triangular TCMT form, 11 mm size 0.8 mm corner radius for robust cutting edge Cylindrical hole with single-sided countersink Consistent cutting performance for medium-steel production The CVD-coated carbide T9215 grade combines wear resistance with good fracture toughness, making it a dependable choice where repeatable tool life and steady cycle times matter. In practical terms, the coating reduces abrasive wear while the substrate keeps the edge intact under load, which translates to fewer interruptions for tool changes and more predictable production planning. This behaviour is particularly beneficial for machining runs with long interrupted cycles or where part throughput is a priority. Secure geometry and reliable clamping for reproducible results The triangular TCMT geometry with an 11 mm size and 60° included angle provides a stable cutting line and an accessible indexing scheme. A 0.8 mm corner radius improves edge strength at the insert tip, supporting heavier feed rates without compromising surface integrity. The insert is supplied with a cylindrical hole and a single-sided countersink (40°–60°) to ensure repeatable, vibration-resistant clamping when paired with the correct holder and shim set. Compatibility with a given toolholder depends on form, clearance angle, tolerance class, fastening method, size and thickness; matching these parameters delivers the intended stability at the cutting zone. Versatile system approach to increase productivity As part of an ISO indexable turning system, the plate works together with a suitable external holder or boring bar, a backing shim or clamping kit and replacement screws to form a complete, serviceable cutting solution. The one-sided chipbreaker suits a range of turning tasks and, when selected alongside the T9215 grade, supports productive material removal rates for medium steels. Selecting the correct chipbreaker and cutting data for the workpiece setup reduces rework and improves cycle consistency, which is crucial for batch production and lean manufacturing environments. For application advice, grading recommendations or to request a quotation for Tungaloy TCMT110308 T9215 inserts, contact Metav Werkzeuge by email at info@metav-werkzeuge.com or by phone on +49 2822 7131930 to discuss the optimal system configuration for the intended turning task. Technical data Article number: 6951454 Manufacturer SKU: TUN6951454 SKU: 6951454-Tungaloy Brand: Tungaloy Facts Size: 11 mm Thickness: 3.18 mm Corner radius: 0.8 mm Clearance angle: 7° Included angle: 60° Grade: T9215 Material: carbide Special features CVD-coated carbide Triangular insert (TCMT) With hole Cylindrical hole + single-sided countersink (40°–60°) One-sided chipbreaker For external and internal turning ISO indexable turning insert series FAQ What materials is this insert suited to machine? The TCMT110308 T9215 insert is optimised for medium-steel machining thanks to its CVD-coated T9215 carbide formulation, offering a balance of wear resistance and fracture toughness for continuous to lightly interrupted cuts. How is the insert mounted and what hole style does it use? The insert features a cylindrical mounting hole with a single-sided countersink (40°–60°) to provide secure clamping in compatible ISO holders; correct matching of holder form and tolerance class ensures stable fixation. Which toolholder types are compatible with this geometry? Compatibility requires a holder designed for triangular TCMT inserts with a 60° included angle and corresponding size and thickness; the full system includes holder, backing shim/clamping set and screws. When should the 0.8 mm corner radius be chosen over a smaller radius? A 0.8 mm corner radius favours edge robustness and allows higher feed rates while reducing the risk of chipping, making it suitable where longer tool life and moderate surface finish are required. Does the chipbreaker suit interrupted cuts? The one-sided chipbreaker is designed for a range of turning tasks; combined with the T9215 grade it performs well in continuous-to-lightly-interrupted applications, though severely interrupted cuts may require a different chip control solution. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
TCMT 110308 T9215 Wendeplatten - Tungaloy
Benefit from the combination of the CVD-coated T9215 grade and a robust 0.8 mm corner radius that deliver high wear resistance and fracture toughness for medium steel turning; order the TCMT110308 insert directly via Metav Werkzeuge or consult the technical advisers for support and compatibility checks. TCMT110308 T9215 Turning Insert (CVD-coated Carbide) – Tungaloy The TCMT110308 T9215 is an ISO triangle turning insert designed for external and internal turning on medium steels, offering a balance of productivity and edge stability. CVD-coated carbide grade T9215 for steel machining ISO TCMT110308 triangle insert, 7° relief angle 0.8 mm corner radius for robust edge strength Countersunk hole fit with 40°–60° seating, 3.18 mm thickness Consistent machining through advanced CVD coating and grade selection The combination of CVD-coated carbide and the T9215 grade provides a predictable balance between wear resistance and toughness, making the insert a dependable choice for continuous to lightly interrupted cuts in medium steels. CVD coating creates a ceramic barrier on the carbide substrate that reduces abrasive wear and improves thermal stability; this translates into longer interval times between indexings and more consistent part quality. The controlled substrate toughness helps to resist chipping, so machining processes remain stable even under variable cutting conditions, supporting higher overall output. Stable seating and geometry for repeatable tool performance Conformance to ISO geometry and the 7° relief angle ensure reliable clearance and chip flow when paired with suitable holders. The insert’s 3.18 mm thickness and triangular form provide a secure clamping surface, while the cylindrical hole with a single-sided countersink (40°–60°) guarantees correct seating and torque transmission. The 60° included angle of the triangle contributes to stiffness in the cutting zone, reducing vibration and improving surface finish. Correct holder selection is decisive: compatibility depends on holder form, tolerance class, fastening method, size and thickness, so the insert should be matched to the clamping system for optimal results. Durable edge and efficient chip control for productive turning A 0.8 mm corner radius gives the cutting edge extra reinforcement for rougher passes and intermittent engagements, reducing the likelihood of premature edge failure. The single-sided chipbreaker channel is designed to control chip formation for a wide range of turning operations, helping to avoid entanglement and to ease evacuation. Together, these features support higher feed rates and sustained cutting conditions, improving productivity while maintaining surface quality. The insert is intended to be used as part of a system—insert, external holder or boring bar, shim/seat and fastening hardware—to enable fast replacements and minimal setup time. For high-productivity medium-steel turning with Tungaloy quality, order genuine TCMT110308 inserts via Metav Werkzeuge or contact Metav Werkzeuge’s technical advisers at info@metav-werkzeuge.com / +49 2822 7131930 for assistance with selection and holder compatibility Technical Data Article number: 6774032 SKU: 6774032-Tungaloy Model series: ISO-Drehwendeschneidplatten Designation: TCMT110308 Material: CVD-coated carbide (T9215) Application: Turning Core dimensions Size: 11 mm Thickness: 3.18 mm Corner radius: 0.8 mm Relief angle: 7° Included angle: 60° Hole: cylindrical hole with single-sided countersink (40°–60°) Shape: triangular Design & features Grade: T9215 Chipbreaker: single-sided System build: insert, holder/boring bar, shim/clamp, replacement screws Typical use: external and internal turning on medium steels Compatibility: defined by holder form, relief angle, tolerance class, fastening and size FAQ What materials is this insert best suited for? The TCMT110308 turning insert in grade T9215 is optimised for medium steel machining; the CVD-coated carbide construction delivers the wear resistance and toughness required for productive steel turning. How does the 0.8 mm corner radius affect performance? A 0.8 mm corner radius increases edge strength and chip load capacity, which helps the TCMT110308 insert withstand rougher passes and light interruptions while maintaining surface quality. Which holder features are required for secure clamping? Secure clamping requires a holder that matches the ISO triangle form, accepts the 11 mm size and 3.18 mm thickness, and accommodates the cylindrical hole with a single-sided countersink as specified for correct seating. What operational benefits does the T9215 grade offer? T9215 provides a balance of high wear resistance and fracture toughness, enabling sustained cutting at higher productivity for continuous to lightly interrupted turning operations. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
TCMT 110308 T9215 Wendeplatten - Tungaloy
Take advantage of the combination of high wear resistance, fracture toughness and precise ISO geometry to keep turning operations productive and predictable; order genuine Tungaloy inserts via Metav Werkzeuge or consult our specialists for application-specific advice. TCMT 110308 T9215 indexable turning insert for ISO-format turning — Tungaloy TCMT 110308 T9215 indexable insert for external and internal turning, designed for medium steel machining with a 60° triangular geometry and a 0.8 mm nose radius. CVD-coated cemented carbide grade T9215 ISO TCMT 110308 format, 60° triangle 0.8 mm nose radius for reduced cutting forces Cylindrical hole with one-sided countersink 40°–60° Reliable wear resistance for continuous to lightly interrupted turning The TCMT 110308 insert combines a CVD-coated cemented carbide substrate with the T9215 grade to deliver an excellent balance of wear resistance and edge strength for medium-steel applications. The CVD coating improves resistance to abrasive wear and thermal effects, which supports longer, consistent tool life under steady cutting conditions. For production environments prioritising throughput, the coated carbide reduces the frequency of index changes and contributes to predictable cycle times and lower overall tooling costs. Geometry engineered for stable machining and surface quality The 60° triangular geometry and 0.8 mm nose radius give a stable cutting edge suitable for both finishing and light roughing in turning operations. The insert’s 7° clearance angle and a plate thickness of 3.18 mm ensure robust support in the pocket, reducing chatter and enabling better surface finishes. As an ISO-format insert, compatibility with holders depends on shape, clearance, tolerance class, fastening and thickness; matching these parameters preserves clamping integrity and repeatability across tool changes. Practical benefits on the shop floor: productivity and process security A single-sided chipbreaker paired with the T9215 grade helps to control chip formation when machining medium steels, improving evacuation and reducing interruptions. This combination supports higher metal-removal rates while maintaining edge stability, which is particularly useful in continuous or slightly interrupted cuts. The result is a lower cost per component through extended index life and reduced tool-change downtime, making the insert an efficient choice for small-batch to high-volume turning tasks. System compatibility and selection advice for turning setups The insert is supplied in the ISO indexable system context and is intended for use with a suitable external holder or boring bar, plus a matching underlay/clamping set and replacement screws where required. The plate’s cylindrical hole with one-sided countersink (40°–60°) enables secure fastening and precise seating. When selecting an insert variant, consider workpiece material, cutting parameters and machine stability; the T9215 grade is the recommended first choice for general medium-steel machining due to its balance of wear resistance and toughness. Contact Metav Werkzeuge for tailored recommendations on Tungaloy turning solutions and to order genuine TCMT 110308 T9215 inserts suited to specific machining conditions. Technical data Article number: 6773980 Manufacturer SKU: TUN6773980 Item SKU: 6773980-Tungaloy Manufacturer: Tungaloy Facts Format: TCMT 110308 Insert size: 11 mm Thickness: 3.18 mm Nose radius: 0.8 mm Clearance angle: 7° Included angle: 60° Special features Grade: T9215 Material/coating: CVD-coated cemented carbide Plate shape: triangular Chipbreaker: single-sided Hole: with cylindrical hole and one-sided countersink 40°–60° Application: turning (external and internal) ISO indexable turning insert compatible with matching holders and clamping sets FAQ What materials is this insert best suited for? The TCMT 110308 T9215 Tungaloy insert is optimised for medium steel machining; the T9215 grade offers a good balance of wear resistance and fracture toughness for continuous to lightly interrupted cuts. Which geometry features improve surface finish and stability? The 60° triangular geometry combined with a 0.8 mm nose radius and 7° clearance reduces cutting forces and improves support in the pocket, resulting in more stable cutting and improved surface quality. How is the insert secured in a holder? This ISO-format insert uses a cylindrical hole with a one-sided countersink (40°–60°) for positive clamping; compatibility requires matching insert form, thickness and tolerance class with the selected external holder or boring bar. Is this insert suitable for interrupted cuts? The T9215 grade provides sufficient toughness for light to moderate interruptions; for heavy interrupted cuts, assess machine stability and consider inserts with enhanced edge robustness. Can the chipbreaker be used for a range of feed rates? The single-sided chipbreaker on this insert supports controlled chip formation across typical turning feed ranges for medium steels, aiding evacuation and reducing the risk of built-up edge. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
TCMT 110308 T9225 Wendeplatten - Tungaloy
Take advantage of a robust CVD‑coated carbide grade and ISO‑standard geometry for reliable medium to heavy steel turning; the combination of the T9225 grade’s toughness and the insert’s secure mounting ensures consistent cycle times and fewer index changes. Order via Metav Werkzeuge or request guidance from their consultants for holder compatibility and chipbreaker selection. TCMT110308 T9225 — ISO turning indexable insert by Tungaloy, CVD‑coated carbide The TCMT110308 T9225 is an ISO‑standard triangular turning insert designed for external and internal turning, offering a robust universal grade for mixed and slightly interrupted cuts in steel. CVD-coated carbide for robust performance Triangular ISO shape with 60° included angle 0.8 mm corner radius for stable cutting edges Countersunk hole for secure mounting Process reliability through a tough CVD‑coated grade The combination of a CVD‑coated surface and a carbide substrate in the T9225 grade provides a balanced mix of hardness and toughness, making the insert particularly suitable for medium to heavy machining of steel. The coating improves wear resistance at elevated cutting temperatures while the substrate preserves edge integrity during slight interruptions in the cut. This translates into longer tool life and reduced change‑over frequency, which supports steady throughput and lower cost per component in production environments. Geometry and mounting that support repeatable accuracy A triangular form with a 60° included angle and a 0.8 mm corner radius delivers predictable cutting behaviour and robustness at each indexed edge. The insert’s 7° clearance angle and a thickness of 3.18 mm increase stiffness in the cutting zone, improving dimensional stability and surface finish when paired with a matching ISO holder. The central cylindrical hole with a single‑side countersink (40°–60°) ensures secure mounting and repeatable seating, minimising run‑out and contributing to consistent part quality across batches. System approach and application guidance for turning operations As an ISO‑standard insert, compatibility depends on holder form, clearance, tolerance class, clamping method, size and thickness. Selecting the correct chipbreaker and matching the grade to machine stability and workpiece material ensures optimal performance; this insert is intended for external and internal turning where a universal, tough grade is required. For mixed production lots or setups with variable engagement, the grade’s design reduces the need for frequent grade swaps and eases process planning. Economic benefits and process security in daily production Using a universal, robust grade reduces inventory complexity and the frequency of tool changes, which helps to cut downtime and administrative effort. The insert’s wear‑resistant coating and mechanically secure mounting contribute to consistent cycle times and predictable maintenance intervals — factors that enhance overall process security and support more reliable production planning. Choosing a well‑matched insert like this one helps maintain surface quality while keeping operational costs under control. For availability and tailored holder recommendations for the Tungaloy TCMT110308 T9225 indexable insert, contact Metav Werkzeuge for expert consultation and fast supply Technical data Article number: 6781310 Manufacturer SKU: TUN6781310 Model series: ISO‑Drehwendeschneidplatten Material: Carbide Application: Turning Core dimensions Included angle: 60° Corner radius: 0.8 mm Thickness: 3.18 mm Size: 11 mm Clearance angle: 7° Mounting hole: cylindrical hole with single‑side countersink (40°–60°) Special features Grade: T9225 Coating: CVD‑coated Chipbreaker: one‑sided Shape: triangular Compatibility: ISO turning holders Typical use: external and internal turning FAQ What materials is this insert best suited for? The TCMT110308 T9225 insert is optimised for steel machining, offering toughness and wear resistance suited to medium and heavy cuts. How does the T9225 grade behave with interrupted cuts? The T9225 grade combines a tough substrate with a CVD coating to maintain edge strength during slightly interrupted or variable engagements, improving reliability in such conditions. Which chipbreaker should be chosen for roughing? Select a more robust chipbreaker matched to the workpiece material and machine stability; the TCMT110308 T9225 is compatible with one‑sided chipbreaker options designed for heavy‑cut performance. Is the insert compatible with all ISO holders? The insert follows ISO geometry but compatibility depends on holder form, clearance, tolerance class, clamping method, size and thickness; verify holder specifications against the insert dimensions before mounting. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
TCMT 110308 T9225 Wendeplatten - Tungaloy
Take advantage of the robust T9225 grade and CVD‑coated carbide construction for consistent medium-to-heavy steel turning; the ISO form and 7° clearance ensure straightforward interchangeability with ISO holders. Order the insert directly via Metav Werkzeuge or consult their advisers for process support. TCMT110308 T9225 TCMT indexable turning insert — CVD‑coated carbide, 0.8 mm nose radius — Tungaloy A TCMT110308 T9225 indexable turning insert designed for medium-to-heavy steel turning, compatible with ISO holder systems and intended for reliable external and internal turning operations CVD-coated carbide for durable performance Universal T9225 grade for medium–heavy steel Triangular form, 3.18 mm plate thickness 0.8 mm nose radius with 7° clearance Precision and consistent cutting performance for demanding steel work The TCMT110308 combines a CVD-coated surface with a wear-resistant carbide substrate to deliver predictable tool life under varying engagement conditions. The T9225 grade was developed as a robust universal option for mid to heavy-duty steel turning where interrupted cuts or fluctuating forces require additional toughness; this reduces unexpected tool changes and supports steady production rates. The indexable insert format permits rapid indexation and replacement, helping to keep machine uptime high and tooling costs controlled. Straightforward compatibility and easy mechanical handling in the workshop Designed to the ISO form, the triangular geometry and defined dimensions make the insert compatible with a wide range of ISO external holders when the form, clearance angle (7°), tolerance class, fastening and thickness match the clamping system. The plate features a cylindrical hole with a single‑side countersink (40°–60°) for secure fixing and repeatable positioning. The 11 mm inscribed circle and 3.18 mm plate thickness offer a compact, rigid solution for many turning set-ups while the 0.8 mm nose radius balances edge strength with surface finish capability. Choose the right chip control and grade for process reliability Select the matching chipbreaker and the T9225 grade according to the workpiece material and machine stability to gain consistent chips and surface quality. The single-sided chipbreaker suits many general turning tasks and helps evacuate swarf efficiently, lowering the risk of re-cutting chips or built-up edge. Using a robust turning insert such as this reduces scrap rates and contributes to predictable cycle times — a practical way to improve throughput while maintaining part accuracy and finish. Contact Metav Werkzeuge for application advice and ordering of Tungaloy inserts — email info@metav-werkzeuge.com or call +49 2822 7131930 Technical Data Article number: 6951423 Manufacturer's SKU: TUN6951423 SKU: 6951423-Tungaloy Model series: ISO turning indexable inserts Designation: TCMT110308 T9225 Numbers / Core technical data Inscribed circle / size: 11 mm Plate thickness: 3.18 mm Clearance angle: 7° Included angle: 60° Nose radius: 0.8 mm Designs / Special features Triangular plate form With hole; cylindrical hole + single‑side countersink (40°–60°) Single-sided chipbreaker CVD-coated carbide grade T9225 Intended application: turning (external and internal) Compatibility depends on form, clearance angle, tolerance class, fastening, size and thickness FAQ Which holder types are compatible with this TCMT insert? Compatibility is determined by the ISO form, the 7° clearance angle, tolerance class, fastening method and plate thickness; the TCMT110308 fits holders designed for TCMT‑type triangular inserts. For which materials is the T9225 grade recommended? The T9225 carbide grade is a robust universal choice for medium to heavy steel turning where toughness against interrupted cuts is required. Can the insert be used for internal turning as well as external turning? Yes, the insert is suitable for both external and internal turning operations when the correct holder geometry and cutting parameters are applied. What does the cylindrical hole with countersink mean for clamping? The cylindrical hole plus single‑side countersink (40°–60°) ensures secure, repeatable clamping and accurate seat positioning in standard ISO toolholder systems. How should the chipbreaker be selected for best results? Choose a chipbreaker that matches the workpiece material and machining stability; the single‑sided chipbreaker fitted to this insert promotes effective chip control in many turning scenarios. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
TCMT 110308 T9225 Wendeplatten - Tungaloy
Taking advantage of a CVD-coated carbide grade that balances toughness and wear resistance with a 0.8 mm corner radius, this insert delivers stable performance in medium to heavy steel turning. Combine its ISO compatibility and robust chip control for reliable cycle times and reduced tool-change frequency; order or discuss application details with Metav Werkzeuge for tailored advice. TCMT 110308 T9225 Turning insert — TCMT110308 Tungaloy TCMT110308 T9225 Tungaloy insert for ISO-standard turning applications, designed for external and internal turning where robustness and chip control are required CVD-coated carbide for heavy steel machining Triangular ISO insert, 11 mm size Single-sided chipbreaker for stable chips 0.8 mm corner radius for a strong edge Consistent cutting performance for medium to heavy steel work The CVD-coated carbide construction and the T9225 grade combine to offer a robust universal grade that copes well with varying engagement and mildly interrupted cuts. The coating improves wear resistance at elevated temperatures, while the carbide substrate maintains toughness; this balance reduces flank wear and supports longer tool life under demanding conditions. The insert’s geometry is optimised to produce predictable cutting forces, which aids process planning and contributes to steady cycle times in production environments. Clear compatibility and secure clamping for straightforward integration Designed as an ISO-standard indexable insert, the triangular shape and precise dimensions ensure interchangeability with matching holders. The triangular form and 11 mm seat size, together with the 3.18 mm plate thickness and 7° clearance angle, determine how the insert mates with the toolholder; compatibility depends on form, clearance angle, tolerance class, fixing method, size and thickness. A cylindrical hole with a single-sided countersink provides positive location and repeatable clamping, helping to maintain concentricity and minimise vibration during external and internal turning operations. Chip control, edge strength and workshop productivity The single-sided chipbreaker promotes consistent chip formation across a range of feeds, improving evacuation and reducing the risk of built-up edge in interrupted cuts. The 0.8 mm corner radius offers a compromise between surface integrity and edge resistance, supporting stable feeds and acceptable surface finish on typical steel components. As part of a system—insert, holder, clamping set and replacement screws—the plate helps to lower downtime through predictable wear behaviour and easier index changes, making it a practical choice for job shops and production lines seeking reliable throughput. Contact Metav Werkzeuge today for application advice or to specify genuine Tungaloy TCMT110308 inserts — technical consultants are available at info@metav-werkzeuge.com or +49 2822 7131930 Technical Data Manufacturer article number: 6781057 SKU: 6781057-Tungaloy Manufacturer SKU: TUN6781057 Model series: ISO-Drehwendeschneidplatten Designation: TCMT110308 Facts Shape: triangular Size: 11 mm Thickness: 3.18 mm Corner radius: 0.8 mm Clearance angle: 7° Included angle: 60° Hole: with hole (cylindrical hole + single-sided countersink 40°–60°) Special features Material: carbide (CVD-coated) Grade: T9225 Chipbreaker: one-sided Application: Turning (external and internal) System: ISO indexable insert; compatible with matching holders, clamping sets and screws FAQ What materials is this insert suited for? The TCMT110308 T9225 insert is a robust universal grade primarily intended for medium to heavy steel machining; its composition and coating support operations with varying engagement and mild interruptions. Which turning operations are appropriate for this insert? This indexable plate is suitable for both external and internal turning; the geometry and single-sided chipbreaker are especially helpful where interrupted cuts or changing cutting conditions occur. How is the insert secured and located in the holder? Compatibility is governed by form, clearance angle, tolerance class, fixing method, size and thickness; the plate features a cylindrical hole with a single-sided countersink (40°–60°) for positive location and repeatable clamping. What benefits does the T9225 grade provide? The T9225 grade offers a balance of toughness and wear resistance due to its CVD coating and carbide substrate, giving reliable edge life under medium to heavy steel cutting and reducing unexpected tool failures. How does the corner radius affect performance? The 0.8 mm corner radius improves edge strength and helps maintain surface integrity under heavier cuts, offering a compromise between finish and robustness for general turning tasks. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
TCMT 110308 T9225 Wendeplatten - Tungaloy
Take advantage of the CVD-coated carbide T9225 and the ISO‑compliant triangular form to secure reliable performance in medium‑to‑heavy steel turning; the combination of toughness and a 0.8 mm corner radius supports stable cutting under variable engagement. Order the TCMT 110308 T9225 turning insert directly via Metav Werkzeuge or ask our consultants if needed. TCMT 110308 T9225 – TCMT turning insert for steel by Tungaloy TCMT 110308 T9225 is a triangular ISO turning insert engineered for robust medium‑to‑heavy steel machining and variable cutting conditions CVD-coated carbide grade T9225 Robust universal grade for steel turning 7° relief angle for stable engagement Cylindrical hole with 40°–60° countersink Stable performance where cutting conditions vary The insert’s CVD-coated surface and T9225 grade combine wear resistance with enhanced toughness, making it suitable for interrupted cuts and fluctuating engagement. As a result, tool life is extended under mixed production scenarios, reducing the frequency of index changes. The design supports consistent metal removal rates while helping to maintain surface quality on medium‑to‑heavy steel, which translates into fewer reworks and steadier cycle times. Easy integration into ISO tooling systems Designed to the ISO TCMT shape, the insert fits common triangular holders when matched by form, clearance, tolerance class, clamping and thickness. This ISO compatibility simplifies tool inventory and shortens tool‑change procedures on the shop floor. The combination of standardised geometry and a triangular footprint offers three usable cutting edges per index, which contributes to lower per‑edge cost and predictable replacement intervals. Better chip control and process security Equipped with a single‑side chipbreaker and a reliable grade, the insert aids chip formation and evacuation during external and internal turning operations. Improved chip control reduces the risk of surface marks and tool interference, supporting higher process stability and safer unattended runs. Selecting the chipbreaker and T9225 grade according to material and machine stability helps to unlock more consistent finishes and repeatable part quality. Design details that support productivity Key dimensions—0.8 mm corner radius, 3.18 mm thickness and an included angle of 60°—combine to offer a balance between edge strength and accessibility in tight profiles. The insert’s 7° relief reduces rubbing and lowers cutting forces at engagement, while the cylindrical hole with a 40°–60° countersink provides secure clamping and reliable index repeatability. These engineered details help to increase uptime and to maintain dimensional accuracy over longer runs. For dependable turning with Tungaloy’s T9225 universal grade, contact Metav Werkzeuge for availability and application advice: info@metav-werkzeuge.com · +49 2822 7131930 Technical data Article number: 6951456 Manufacturer SKU: TUN6951456 Brand: Tungaloy Model series: ISO turning inserts Core dimensions Insert designation: TCMT110308 Size: 11 mm Thickness: 3.18 mm Corner radius: 0.8 mm Relief angle: 7° Included angle: 60° Hole: with hole; cylindrical hole + one‑side countersink (40°–60°) Materials & features Material: carbide Coating: CVD Grade: T9225 Chipbreaker: one‑sided Application: turning Typical use: medium‑to‑heavy steel machining FAQ What materials is this insert suitable for? The TCMT 110308 T9225 insert is formulated for steel machining and performs particularly well in medium‑to‑heavy turning applications where toughness is required. How does the T9225 grade affect tool life? The T9225 CVD coating balances wear resistance and toughness, which extends tool life in interrupted or variable cuts compared with uncoated grades. Is the insert compatible with standard ISO TCMT holders? Yes; the insert follows ISO TCMT geometry and is compatible when matched by form, clearance, tolerance class, clamping and thickness. What is the purpose of the 0.8 mm corner radius? A 0.8 mm corner radius strengthens the cutting edge for heavier engagement while still allowing reasonable profile definition, improving resistance to chipping. Can this insert be used for internal and external turning? The geometry and chipbreaker make the insert suitable for both external and internal turning; selection of holder and cutting data should match the application and machine stability. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
TCMT 160620 AH120 Wendeplatten - Tungaloy
Benefit from the wear- and breakage-resistant AH120 PVD-coated cemented carbide and the precise 60° triangular geometry with an R2 nose radius for stable, repeatable milling results; order the inserts directly via Metav Werkzeuge or consult our technical team if required. TCMT 160620 AH120 indexable insert for milling — Tungaloy The TCMT 160620 AH120 is a triangular indexable insert for milling, engineered for face, shoulder, slot, high-feed and contour operations within compatible Tungaloy milling systems. PVD-coated carbide grade AH120 Sharp cutting edge for stable process control Triangular 60° insert with R2 nose radius Cylindrical hole plus single-side countersink Reliable cutting performance and extended tool life The PVD-coated AH120 grade combines a hard, wear-resistant surface with a robust substrate to deliver consistent cutting performance in demanding milling applications. As a cemented carbide solution with a specifically engineered coating, the insert minimises flank wear and resists chipping during intermittent cuts. This leads to fewer tool changes, reduced machine downtime and a more economical process, particularly where a sharp cutting edge and process stability are essential. The upgrade in edge retention translates into steadier surface finish and predictable tool life, supporting higher productivity targets. Secure clamping and repeatable positioning for safe operation The triangular form with a defined 60° corner angle and R2 nose radius offers predictable engagement and cutting geometry in the toolholder. The insert’s cylindrical hole with a single-side countersink (40°–60°) provides positive, repeatable clamping when used with matching Tungaloy milling bodies and clamping screws. Plate thickness of 6.35 mm contributes to rigidity under load and reduces the risk of movement or vibration. For reliable results, the insert seat, geometry and milling body must be technically compatible, ensuring correct seating, torque distribution and repeatability across tool changes. Versatile application range with controlled chip formation Designed for a wide range of milling tasks, this indexable insert is suitable for face milling, shoulder milling, slotting, high-feed and contouring, depending on the selected tool family. The single-sided chipbreaker supports managed chip flow and lowers cutting forces in many interrupted-cut scenarios, aiding coolant access and chip evacuation. Where a sharp edge and high process security are required, the AH120 grade reduces the likelihood of edge breakdown, making it a dependable choice for production environments that demand consistent part quality and minimal rework. Practical handling and economic advantages on the shop floor Using indexable inserts such as this triangular grade reduces inventory complexity and maintenance time compared with brazed or solid tools: worn corners are simply indexed or replaced, keeping spindle downtime to a minimum. The wear-resistant AH120 coating and sturdy geometry help to maintain dimensional accuracy over multiple edges, contributing to predictable performance and lower total machining costs. For operators seeking a balance of robustness and precision, this insert offers practical benefits that support stable process chains and higher overall equipment effectiveness. Contact Metav Werkzeuge today for tailored application advice and to secure Tungaloy TCMT 160620 AH120 inserts for prompt supply; the technical team is available by email at info@metav-werkzeuge.com or by phone on +49 2822 7131930 Technical data Article number: 6735590 Manufacturer SKU: TUN6735590 Brand: Tungaloy Product designation: TCMT160620 AH120 Core dimensions Inscribed size: 16 mm Thickness: 6.35 mm Nose radius: R2 mm Corner angle: 60° Relief angle: 7° Countersink angle: 40°–60° Special features Grade/coating: AH120 (PVD-coated cemented carbide) Shape: triangular indexable insert Chipbreaker: single-sided Hole style: cylindrical hole + single-side countersink Typical applications: face, shoulder, slot, high-feed and contour milling Designed for stable chip formation and process security FAQ What types of milling operations is this insert suited to? The TCMT160620 AH120 insert by Tungaloy is intended for face, shoulder, slot, high-feed and contour milling when used in compatible tool families. How does the insert ensure secure clamping? Clamping is achieved via the cylindrical hole with a single-side countersink; correct seating and matching holder geometry ensure the TCMT160620 AH120 (SKU TUN6735590) locates and clamps repeatably. What benefits does the AH120 grade provide? AH120 is a PVD-coated cemented carbide grade that offers improved wear resistance and chipping resistance, delivering more consistent tool life and process stability with the TCMT160620 AH120 insert. Can the triangular insert be indexed multiple times? Yes, the triangular geometry provides multiple cutting edges; the insert can be rotated to present a fresh edge, extending the usable life per insert. Are there any special considerations before installation? Ensure the insert seat, holder geometry and clamping screw are compatible with the TCMT160620 AH120 specification and that the countersink and hole align correctly for secure clamping. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
TCMT 160620 AH3135 Wendeplatten - Tungaloy
Benefit from a combination of PVD-coated carbide durability, precise corner radius 2 mm and a triangular form that supports stable milling cycles; the insert is engineered for reliable chip control and reduced downtime. Order the TCMT160620 AH3135 insert via Metav Werkzeuge or consult our specialists for correct matching to the cutter body. TCMT160620 AH3135 – TCMT 160620 milling insert (PVD-coated carbide) by Tungaloy TCMT160620 AH3135 is a triangular indexable insert designed for milling within Tungaloy systems, delivering wear- and chipping-resistant performance where a sharp cutting edge and process security are required. PVD-coated carbide for long tool life Sharp cutting edge for consistent finishes Triangular form for stable chip control Compatible with Tungaloy milling systems Maximised machining reliability and productivity The TCMT160620 AH3135 insert combines a PVD-coated carbide substrate with a grade developed for wear and chipping resistance, offering a dependable cutting edge in demanding milling tasks. This results in fewer tool changes and a more predictable tool life, which improves uptime and reduces unit costs per component. The specification emphasises process reliability: when plate seat, geometry and milling body are matched, the system delivers consistent results across plan, shoulder, slot, high-feed and contour milling operations, depending on the assigned tool family. Engineered geometry for stable cutting and chip control A triangular plate form with a corner radius 2 mm and a 6.35 mm plate thickness gives mechanical stability and resistance to breakage during interrupted cuts. The insert features a one-sided chipbreaker, tuned to support controlled chip formation for milling tasks that demand a sharp edge and reliable evacuation. The central hole with a cylindrical bore and a single-sided countersink (40°–60°) supports secure clamping; this arrangement, together with the 7° clearance angle, helps maintain consistent contact and repeatability when mounted in compatible Tungaloy milling bodies. Coating and material explained for consistent surface quality The PVD coating on the carbide body enhances resistance to abrasive wear and reduces built-up edge formation, which is particularly valuable when machining alloys or mixed-material batches. PVD technology deposits a hard, uniform layer that preserves the sharp cutting edge under cyclic thermal and mechanical stress. For users less familiar with coatings: this means longer intervals between regrinds, improved surface finish and a more reliable process window. The AH3135 grade is intended to balance edge toughness and wear resistance where both a fine cutting geometry and robust performance are required. For personalised application advice and assistance selecting the correct cutter body for this Tungaloy insert, contact Metav Werkzeuge GmbH at info@metav-werkzeuge.com or call +49 2822 7131930 to arrange an allocation check with our technical consultants. Technical Data Article number: 6735589 SKU: 6735589-Tungaloy Manufacturer SKU: TUN6735589 Designation: TCMT160620 AH3135 Brand: Tungaloy Model series: Milling indexable inserts Material: Carbide Plate form: Triangular Plate size: 16 Plate thickness: 6.35 mm Corner radius: 2 mm Clearance angle: 7° Hole style: Cylindrical hole + one-sided countersink (40°–60°) Chipbreaker: One-sided Core figures Insert angle: 60° Plate thickness: 6.35 mm Plate size: 16 mm Corner radius: 2 mm Clearance angle: 7° Special features PVD-coated carbide grade AH3135 Wear- and chipping-resistant design Sharp cutting edge for improved surface quality Suited to face, shoulder, slot, high-feed and contour milling Requires matching plate seat geometry and compatible milling body FAQ What materials is this insert suitable for? The TCMT160620 AH3135 insert is specified for a broad range of milling tasks; the PVD-coated carbide composition offers good performance when machining steels and many alloyed materials where a sharp edge and process security are required. How is the insert held in the cutter body? The insert uses a central cylindrical hole with a single-sided countersink (40°–60°) for screw clamping; ensure the plate seat and cutter body geometry are compatible with the TCMT160620 form to achieve repeatable clamping and positioning. Which milling operations are recommended? Depending on the assigned tool family, the insert is suitable for face milling, shoulder milling, slotting, high-feed and contour milling; the design supports stable chip control and predictable wear behaviour during these operations. What does the AH3135 grade offer compared with other grades? AH3135 is a PVD-coated grade optimised for a balance of edge toughness and wear resistance, making it appropriate where a sharp cutting edge and reliable process performance are both required. Can the insert be used for interrupted cuts? Yes, the triangular form, 6.35 mm thickness and 2 mm corner radius give mechanical robustness that helps withstand interrupted cuts, provided the insert is correctly seated and the milling body is suitable. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
TCMT 160620 T1215 Wendeplatten - Tungaloy
Take advantage of the combination of durable carbide construction, T1215 wear‑resistant grade and a 2 mm corner radius for dependable milling performance; order directly via Metav Werkzeuge or consult the team for application matching and availability. TCMT160620 T1215 TCMT indexable milling insert — triangular, 2 mm radius (Tungaloy) TCMT160620 T1215 is a triangular indexable insert designed for versatile milling tasks within compatible Tungaloy milling systems Triangular insert for stable cutting geometry Grade T1215 with balanced wear resistance 2 mm corner radius for robust edge strength Cylindrical hole with 40°–60° countersink High‑efficiency milling thanks to a balanced carbide grade The combination of carbide substrate and the T1215 grade delivers a balance between wear resistance and toughness, which supports consistent tool life under varied cutting conditions. Designed as an indexable cutting element for milling, the insert’s geometry contributes to stable cutting forces and controlled chip flow. This leads to measurable productivity benefits by reducing index‑change frequency and maintaining dimensional consistency on repeat runs. Secure seating and simple integration into Tungaloy systems The insert is intended for use in dedicated Tungaloy milling bodies where insert seat, geometry and cutter body must match precisely. The cylindrical hole with single‑side countersink (40°–60°) ensures repeatable clamping and accurate positioning, while the 6.35 mm thickness and triangular form provide a stable contact area. These design choices reduce vibration and support predictable engagement with the workpiece, improving surface quality and tool life. Versatile application range and cutting edge stability Suitable for a range of milling operations — from face and shoulder milling to slotting and high‑feed strategies depending on the associated tool family — the insert’s 2 mm corner radius enhances edge robustness, lowering the risk of premature chipping. The single‑sided chipbreaker optimises chip control for many standard milling tasks, simplifying chip evacuation and reducing rework time. The result is a practical, production‑oriented insert that complements modern machining strategies. Cost‑effective operation through predictable performance By combining a recognised Tungaloy grade with a standardised triangular form, the insert supports efficient inventory rotation and straightforward tool management. The stability in edge geometry and the reliable clamping concept translate into fewer unscheduled stoppages and consistent component quality. For procurement and process engineers, this means easier planning of tool cycles and a clearer return on machining hours invested in each cutting edge. Contact Metav Werkzeuge today to confirm suitability and availability of the Tungaloy TCMT160620 T1215 insert — email info@metav-werkzeuge.com or call +49 2822 7131930 for tailored technical advice Technical data Article number: 6774958 SKU: 6774958-Tungaloy Manufacturer item no.: 6774958 Manufacturer SKU: TUN6774958 Material: carbide Model series: milling indexable inserts Numbers / Core technical data Size: 16 mm Thickness: 6.35 mm Corner radius: 2 mm Relief angle: 7° Angle: 60° Designs / Special features Triangular plate form Cylindrical hole with single‑side countersink (40°–60°) Single‑sided chipbreaker Grade T1215 (Tungaloy) Intended for milling applications Compatible with Tungaloy milling systems; seat and cutter body must match FAQ What milling operations is this insert suitable for? The TCMT160620 T1215 indexable insert is designed for face, shoulder, slot, high‑feed and contour milling depending on the assigned tool family. How does the T1215 grade affect performance? Tungaloy’s T1215 grade on this insert provides a balance of wear resistance and toughness, improving cutting edge stability and tool life in representative milling conditions. Is the insert clamped securely in standard Tungaloy cutters? Yes. The design features a cylindrical hole with a 40°–60° single‑side countersink to ensure repeatable positioning and solid clamping when used in compatible Tungaloy milling bodies. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand‑new product from the manufacturer.
TCMT 160620 T3225 Wendeplatten - Tungaloy
Take advantage of the combination of an optimised T3225 grade, a robust 2 mm corner radius and precise 60° geometry to increase machining consistency and tool life; order directly via Metav Werkzeuge or consult our technical advisors for application-specific recommendations. TCMT 160620 T3225 — Indexable milling insert for milling (Tungaloy) TCMT 160620 T3225 is a triangular indexable milling insert designed for use in Tungaloy milling systems and intended for face, shoulder, slot, high-feed and contour milling. Optimised T3225 grade for wear resistance Triangle 16 mm size, 60° geometry 2 mm corner radius for edge strength Compatible with Tungaloy milling systems Boosted tool life through balanced grade properties The T3225 grade combines wear resistance and controlled toughness to prolong edge life in a wide range of milling operations. The cemented carbide substrate and the grade formulation reduce flank wear and delay chipping, which means fewer insert changes and higher process uptime. For operations where consistent surface quality and predictable regrinding intervals matter, this configuration offers clear economic advantages while maintaining the required machining performance. Secure clamping and straightforward replacement for production use Designed with a cylindrical hole with single-side countersink (40°–60°), the insert ensures positive seating and repeatable location in compatible cutter bodies. The triangular 16 mm form factor and the clearly defined 60° geometry make indexing quick and unambiguous, shortening downtime during tool changes. Note that correct interaction between insert seat, geometry and cutter body is essential for reliable clamping and optimal cutting behaviour. Purpose-built geometry and chip control for efficient milling The single-sided chipbreaker and a 2 mm corner radius provide improved chip formation and stable cutting edges in finishing and medium-depth roughing applications. The relief angle of 7° supports smooth engagement and reduces rubbing on the trailing flank. Used as part of a compatible system, this insert helps to maintain consistent surface finish and reduces the incidence of built-up edge, especially in cyclic production runs. Application guidance and system compatibility This triangular insert is intended specifically for milling; typical tasks include face milling, shoulder milling, slotting, high-feed and contour profiling. The insert is supplied for use in Tungaloy milling systems — matching the insert seat and cutter body geometry is a technical requirement for safe and repeatable performance. For customers planning process optimisation, the combination of the T3225 grade and the insert’s geometry can deliver measurable increases in throughput and cost-efficiency. For robust, productive milling choose the Tungaloy T3225 insert and contact Metav Werkzeuge for tailored recommendations or ordering; Metav Werkzeuge’s consultants can advise on system compatibility and application settings Technical data Article number: 6774957 Manufacturer SKU: TUN6774957 SKU: 6774957-Tungaloy Product name: TCMT160620 T3225 Tungaloy indexable milling insert Series: Milling indexable inserts Dimensions & key values Insert size: 16 mm Thickness: 6.35 mm Corner radius: 2 mm Relief angle: 7° Included angle: 60° Materials & features Material: cemented carbide Grade: T3225 Shape: triangular Hole: cylindrical hole with single-side countersink (40°–60°) Chipbreaker: single-sided Application: milling (face, shoulder, slot, high-feed, contour) System note: insert seat, geometry and cutter body must match FAQ Which milling operations are suitable for this insert? This TCMT 160620 T3225 insert is suitable for face milling, shoulder milling, slotting, high-feed and contour applications within compatible Tungaloy milling systems. What materials can be machined with the T3225 grade? The T3225 grade is formulated for a broad range of steels and common workshop materials; the carbide substrate provides wear resistance and edge stability for general milling operations. How important is matching the insert to the cutter body? Correct match of the insert seat, geometry and cutter body is critical; incorrect pairing can compromise clamping, repeatability and cutting performance for the TCMT160620 T3225 insert. What benefit does the 2 mm corner radius deliver? A 2 mm corner radius increases edge strength and helps to distribute cutting forces, reducing the risk of chipping during interrupted cuts or heavier engagement conditions. Is the insert indexed and easy to replace during production? Yes — the triangular form and the cylindrical hole with countersink ensure repeatable positioning and quick indexing, which reduces machine downtime during insert changes. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
TCMT 16T302 AH6225 Wendeplatten - Tungaloy
Take advantage of a PVD-coated carbide grade engineered for reliable stainless steel turning and a sharp, stable cutting edge that performs across changing conditions; order directly via Metav Werkzeuge or consult our specialists for application guidance. TCMT 16T302 AH6225 – TCMT16T302-PS turning insert (0.2 mm radius) by Tungaloy The TCMT16T302-PS AH6225 is an ISO-format triangular turning insert designed for external and internal turning of stainless steels, offering a balanced combination of edge sharpness and stability for medium cutting conditions. PVD-coated carbide for long tool life Designed for stainless steel machining ISO-standard triangular insert, 60° geometry 0.2 mm corner radius for fine finishing Efficient metal removal with consistent edge life The combination of a PVD-coated surface and the AH6225 grade of carbide delivers a durable cutting edge while retaining enough sharpness for demanding stainless steel tasks. This balance ensures stable performance during medium-duty turning operations and helps reduce workpiece rework. The chipbreaker PS supports controllable chip formation under variable cutting conditions, improving process predictability and reducing the frequency of tool changes. For workshops aiming to maintain throughput while preserving surface quality, the engineered pairing of coating and substrate yields measurable gains in uptime and component consistency. Smooth integration into ISO tooling systems for predictable results Compatibility with toolholders is determined by geometry, relief angle, tolerance class, clamping method, size and thickness. The insert follows ISO conventions, so the mechanical fit with a matching external holder or boring bar is straightforward when those parameters align. The overall system comprises the indexable insert, an appropriately rated holder, a shim or clamping set and the retaining screw; correct assembly minimises vibration and supports repeatable cuts. Laboratory measurements and in-shop trials benefit from this standardisation, as operators can swap inserts rapidly while maintaining process settings and expected part tolerances. Fine finishing and practical selection guidance for turning tasks The triangular form and 60° included angle offer versatile cutting orientations and three indexed cutting edges per insert, while the 0.2 mm corner radius supports fine finishing without compromising edge strength. Plate thickness of 3.97 mm and the central hole with a cylindrical bore plus a single-side countersink (40°–60°) ensure secure clamping and stable performance under lathe feeds typical for finishing and semi-finishing passes. When selecting a chipbreaker and grade, choose the chip control and edge preparation that match material characteristics and machine rigidity — for stainless steels under mixed conditions, the AH6225 grade with chipbreaker PS is a dependable choice that balances wear resistance and cutting stability. For tailored advice on machining strategies and to secure original Tungaloy inserts such as the TCMT16T302-PS AH6225, contact Metav Werkzeuge for direct supply and application support via email or phone. Technical data Article number: 6903327 Manufacturer SKU: TUN6903327 SKU: 6903327-Tungaloy Material: carbide Model series: ISO-Drehwendeschneidplatten Designation: TCMT16T302-PS AH6225 Tungaloy-Wendeplatte Core data Size: 16 Thickness: 3.97 mm Corner radius: 0.2 mm Relief angle: 7° Included angle: 60° Grade: AH6225 Design & features Triangle plate form Chipbreaker: PS Hole: with hole — cylindrical hole + single-side countersink (40°–60°) Coating: PVD Application: Turning (external and internal) System composition: ISO insert, matching holder or boring bar, shim/clamping set and spare screws Compatibility determined by form, clearance angle, tolerance class, clamping, size and thickness FAQ Is this insert suitable for stainless steel turning applications? Yes. The TCMT16T302-PS in AH6225 grade is specifically designed for machining stainless steels and combines a PVD-coated carbide substrate with the PS chipbreaker to control chips and maintain edge stability. What does the 0.2 mm corner radius affect in practice? A 0.2 mm corner radius helps achieve finer surface finishes and reduces the risk of cutting-edge chipping during finishing passes; the radius is a compromise between edge strength and surface quality for many turning operations. How does the insert fasten to a holder? The triangular insert uses a central bore with a cylindrical hole and single-side countersink (40°–60°) to enable secure clamping in compatible ISO-format holders and boring bars; ensure holder geometry matches the insert form and tolerance class. Can this insert be used for internal turning as well as external turning? Yes. The ISO triangular geometry and 60° included angle make the insert suitable for both external and internal turning, provided an appropriate holder or boring bar is selected for the operation. What should be considered when choosing the chipbreaker? Select the chipbreaker according to workpiece material, feed rate and machine rigidity; the PS chipbreaker on this insert is intended to offer predictable chip control for variable conditions in stainless steel machining. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
TCMT 16T302 AH6235 Wendeplatten - Tungaloy
Take advantage of a PVD-coated AH6235 grade that delivers robust performance in stainless-steel turning and interrupted cuts, combined with a 60° triangular geometry and a 0.2 mm corner radius for accurate profile control; order directly via Metav Werkzeuge or contact the consultants for application advice. TCMT 16T302 AH6235 Tungaloy indexable insert (turning) — PVD-coated carbide, 60° triangle The TCMT16T302-PS AH6235 is an ISO-compliant indexable insert for external and internal turning, engineered for stainless-steel machining and interrupted-cut conditions. PVD-coated carbide AH6235 for tough stainless steels ISO TCMT16T302 triangular insert, 60° included angle 0.2 mm corner radius for precise profile control High cutting reliability and extended tool life through material design The insert combines a PVD-coated carbide substrate with a tougher cutting grade, AH6235, to resist chipping in interrupted cuts and under unstable cutting conditions. The coating reduces adhesion and improves wear resistance, which translates into longer life and fewer tool changes. For manufacturers seeking predictable cycle times, the insert’s material combination supports consistent edge performance and helps maintain surface finish on demanding alloys such as stainless steel. Designed geometry for repeatable profiles and secure clamping With a 60° triangular shape and a 0.2 mm corner radius, the insert provides a balance between strength and profile definition. The central hole with a cylindrical bore and a one-sided countersink (40°–60°) ensures secure clamping in compatible holders; compatibility is determined by form, free clearance angle, tolerance class, fixing method, size and thickness. As an ISO-standard indexable insert, it integrates readily into common toolholder systems when these parameters match, enabling straightforward replacement and reduced setup time. Practical selection guidance to match process requirements Chip control is handled by the PS chipbreaker, which is suitable for interrupted and difficult-to-machine surfaces, helping to avoid built-up edge and unstable chips. The insert’s thickness (3.97 mm) and size (16 mm) provide sufficient mass for stability in medium-duty turning operations while the 7° free clearance angle assists with cutting-edge accessibility. Choosing this insert for stainless-steel components or applications with frequent interruptions will often reduce rework and increase throughput when combined with an appropriate holder and cutting data. Integration and operational benefits for production workflows Because the insert is ISO-standardised, spare-part logistics and tool preset strategies are simplified: identical geometry reduces inventory variety and facilitates predictable tool-change procedures. The combination of grade, coating and chipbreaker aims to deliver consistent surface quality and stable chip formation, which in turn supports automated or semi-automated turning processes. For production environments where repeatability and uptime matter, the insert contributes to efficient machining cycles and controlled process economics. For stainless-steel turning tasks that demand reliability and reduced edge failure, consider the Tungaloy AH6235 TCMT16T302-PS insert — contact Metav Werkzeuge for stock availability and application-specific recommendations. Technical Data Article number: 6903492 Manufacturer SKU: TUN6903492 Label: TCMT16T302-PS AH6235 Tungaloy insert Model series: ISO turning indexable inserts Material: Carbide Core Data Plate size: 16 mm Thickness: 3.97 mm Corner radius: 0.2 mm Free clearance angle: 7° Included angle: 60° Hole: with cylindrical hole + one-sided countersink (40°–60°) Special Features Grade/coating: AH6235 (PVD-coated carbide) Chipbreaker: PS Shape: triangular Application: turning — external and internal turning; suitable for interrupted cuts and stainless steels Compatibility criteria: form, clearance, tolerance class, clamping method, size and thickness FAQ Is this insert suitable for machining stainless steel? The TCMT16T302-PS AH6235 insert is designed for stainless-steel turning and provides enhanced resistance to chipping and adhesive wear thanks to the AH6235 grade and PVD coating. Can this insert handle interrupted cuts? Yes — the AH6235 grade combined with the PS chipbreaker is intended for interrupted cutting conditions and applications with elevated breakout risk. What are the key dimensional features to match with a holder? Ensure the holder accommodates a TCMT-style triangular insert with a 16 mm size, 3.97 mm thickness, a 60° included angle and the central hole geometry (cylindrical bore plus one-sided countersink). What benefit does the 0.2 mm corner radius provide? A 0.2 mm corner radius balances edge strength and profile accuracy, improving resistance to chipping while maintaining a defined turned contour. Which applications are most appropriate for this insert? The insert is intended for external and internal turning operations on stainless-steel components and for situations where interrupted cuts or unstable chip formation are common. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
TCMT 16T302 AH725 Wendeplatten - Tungaloy
Benefit from the combination of a PVD-coated carbide grade and ISO TCMT geometry for consistent chip control and high process security; order directly via Metav Werkzeuge or consult our specialists for holder compatibility and cutting-geometry advice. TCMT 16T302 AH725 — Indexable turning insert by Tungaloy (for turning) TCMT16T302-PS AH725 Tungaloy-Wendeplatte is an ISO-format indexable insert engineered for external and internal turning, offering universal, fracture-resistant performance for varied materials. TCMT ISO triangular insert, 16 mm size PVD-coated carbide grade AH725 Fracture-resistant for Stahl and rostfreier Stahl Compatible with 7° relief and 60° angle holders Reliable cutting performance with proven coating technology The combination of PVD-coated carbide and the AH725 grade delivers a balanced wear resistance and toughness, designed for mixed-series production where material changes are common. The coating process forms a hard surface layer that reduces flank wear and increases thermal stability during interrupted cuts, which improves tool life and process reliability. For shops machining both Stahl and rostfreier Stahl, this solution reduces the risk of edge chipping while maintaining consistent tool performance and surface quality. Simple integration into ISO turning systems for quick tool changes As an ISO-format component, the TCMT16T302-PS designation indicates a triangular insert with the specific geometry and mounting features required for standard indexable holders. Key geometric specifications such as corner radius 0.2 mm, 3.97 mm thickness, 7° relief and the 60° included angle determine mechanical fit and cutting engagement; the insert also features a cylindrical hole with a single-sided countersink (40°–60°) for positive clamping. These measurable values support straightforward verification of compatibility with existing holders and clamping sets, minimising setup time and ensuring repeatable, safe seating during index changes. Controlled chip flow and secure machining for higher uptime The PS chipbreaker is matched to the insert geometry and the AH725 grade to promote predictable chip formation and evacuation in turning operations, improving surface finish and reducing the likelihood of built-up edge or machine interruptions. This indexable insert is suitable for both external and internal turning applications where stable chip control and process security are priorities. Backed by Tungaloy’s engineering, the design focuses on productive metal removal while preserving edge integrity in mixed-material production scenarios. For specific recommendations on holder selection, cutting parameters or batch optimisation with the Tungaloy AH725 TCMT16T302-PS insert, contact Metav Werkzeuge at info@metav-werkzeuge.com or call +49 2822 7131930 to arrange application-focused advice from our technical team. Technical data Article number: 6856796 Manufacturer SKU: TUN6856796 SKU: 6856796-Tungaloy Model series: ISO-Drehwendeschneidplatten Data Size: 16 mm Thickness: 3.97 mm Corner radius: 0.2 mm Relief angle: 7° Included angle: 60° Countersink angle: 40°–60° Special features Grade: AH725 Material: Hartmetall Coating: PVD-coated carbide Chipbreaker: PS Shape: triangular Hole: with cylindrical hole + one-sided countersink Typical use: external and internal turning Compatibility criteria: form, relief angle, tolerance class, clamping, size, thickness FAQ Is this insert suitable for stainless steels? Yes. The TCMT16T302-PS in AH725 grade is specified as a universal, fracture-resistant option for both Stahl and rostfreier Stahl, providing improved edge stability when machining mixed materials. What does the PS chipbreaker do? The PS chipbreaker on the insert is designed to influence chip formation and evacuation during turning operations; when combined with the AH725 grade it supports consistent chip control and surface finish in general turning tasks. How is holder compatibility determined? Compatibility depends on measurable characteristics: insert form, 7° relief, tolerance class, clamping method, 16 mm size and 3.97 mm thickness; verifying these values ensures correct seating and secure clamping of the indexable insert. Can the insert be used for internal turning? Yes. The insert is intended for both external and internal turning; correct holder selection and appropriate cutting parameters are important for secure, stable machining. What is indicated by the ISO code TCMT16T302-PS? The ISO code denotes the insert geometry, size and chipbreaker style; it identifies a triangular ISO insert in the 16 size class with the T302 geometry and PS chipbreaker, enabling standardised selection for compatible holders. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
TCMT 16T302 NS9530 Wendeplatten - Tungaloy
Benefit from precise finishing performance and reduced cutting forces delivered by the NS9530 cermet grade together with ISO compatibility for straightforward tool selection; order directly via Metav Werkzeuge or ask the consultants for application advice. TCMT 16T302 NS9530 – indexable insert for turning, Tungaloy A TCMT 16T302 NS9530 indexable insert designed for finishing turning of steel, offering a sharp cutting edge and low cutting forces for excellent surface quality. ISO‑standard triangular 16 mm insert Uncoated cermet NS9530 grade Sharp cutting edge for superior surface finish Cylindrical hole with countersink for secure clamping Achieve superior surface finish with low cutting forces The NS9530 uncoated cermet grade has been developed for finishing operations on steel, providing a sharp cutting edge and notably low cutting forces. These properties reduce tool-induced vibration and support a stable process, especially during continuous cuts and small depth‑of‑cut passes. For applications where surface integrity and dimensional accuracy are decisive, this insert promotes fewer secondary operations and consistent part quality. Reliable clamping and ISO compatibility for predictable set‑ups The insert follows ISO geometry and is a triangular 16 mm form with a 60° included angle, featuring a cylindrical hole with a one‑sided countersink (40°–60°) for secure fastening. The standardised shape and tolerance class ensure interchangeability with ISO‑compliant holders; compatibility is determined by form, relief angle, tolerance class, fastening, size and thickness. The 7° relief angle and 3.97 mm thickness contribute to predictable positioning and repeatable clamping, reducing set‑up time and minimising the need for bespoke fixtures. Improve productivity by reducing rework and stabilising cycles Using a finishing‑oriented insert such as this one shortens the production chain: the combination of a precision edge and material‑matched chipforming decreases the likelihood of surface defects and the need for additional finishing passes. The design supports reduced cycle times and more consistent batch quality, which is particularly relevant in serial production where process stability and repeatability are key economic drivers. The modest 0.2 mm corner radius is optimised for fine surface finish without compromising on dimensional control. For technical selection and ordering, contact Metav Werkzeuge for tailored advice or to confirm holder compatibility and recommended cutting data. Technical Data Article number: 6998515 SKU: 6998515-Tungaloy Manufacturer SKU: TUN6998515 ISO designation: 16T302 Insert designation: TCMT16T302-PS Facts Insert size: 16 mm Corner radius: 0.2 mm Thickness: 3.97 mm Relief angle: 7° Included angle: 60° Special features Grade: NS9530 (uncoated cermet) Chipbreaker: PS Form: triangular Hole: cylindrical hole + one‑sided countersink (40°–60°) Typical application: finishing for steel turning Compatibility: ISO‑standard indexable insert, requires matching holder and clamping kit FAQ What materials is this insert suitable for? This insert is specified as a finishing grade for steel; the NS9530 uncoated cermet is particularly suited to continuous cuts and small depths of cut on steel. Which holders are compatible with this insert? Holders complying with the ISO triangular insert form and matching the 16 mm size, 3.97 mm thickness and 60° included angle are compatible; ensure the holder accepts a cylindrical hole with countersink as described. What benefits does the PS chipbreaker provide? The PS chipbreaker supports stable chip control during finishing passes, improving surface quality and reducing the chance of secondary operations. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
TCMT 16T302 T6215 Wendeplatten - Tungaloy
Take advantage of the combination of CVD-coated carbide (T6215) wear resistance and a compact 0.2 mm corner radius for reliable stainless-steel turning under stable to slightly interrupted cuts; order directly via Metav Werkzeuge or consult our application experts for compatibility and delivery options. TCMT 16T302 T6215 indexable turning insert – triangular ISO insert for turning, Tungaloy TCMT16T302-PS T6215 insert for ISO-compliant turning of stainless steels, designed for stable cutting conditions and straightforward replacement in standard indexable holders ISO triangular turning insert TCMT 16T302 CVD-coated T6215 grade for stainless steels 0.2 mm corner radius, 60° included angle Cylindrical hole with single-side countersink Precision wear control for stainless-steel turning The insert delivers consistent performance thanks to its CVD-coated composition and T6215 grade, providing enhanced resistance against abrasive and adhesive wear common in machining stainless steels. CVD coating creates a hard, thermally stable outer layer that reduces flank wear and extends tool life; this results in fewer index changes and more predictable process windows. The design supports machining under stable to slightly interrupted conditions, reducing scrap rates and improving process efficiency for serial production and jobbing environments. Compatibility and secure clamping to reduce downtime Compatibility with the toolholder is defined by form, clearance angle (7°), tolerance class, clamping method, size and thickness. The triangular geometry with a 60° included angle and central fixing hole means the insert seats securely in conventional indexable turning holders. The cylindrical hole with a single-side countersink (40°–60°) ensures reliable clamping and repeatable seating, which minimises vibration and helps maintain consistent cutting conditions over repeated insert exchanges. Geometry and chip control that boost productivity A 0.2 mm corner radius balances cutting-edge strength and profile accuracy: it offers sufficient edge robustness for interrupted cuts while keeping surface finish and dimensional control at acceptable levels. The integrated PS chipbreaker is tuned for stainless-steel cutting dynamics, promoting controllable chip forms and aiding coolant penetration. The insert’s 3.97 mm thickness contributes to rigidity in the clamped assembly, lowering the risk of chatter and enabling higher metal removal rates where machine and setup permit. Choosing the right insert for the task As part of an ISO insert system, selection should consider holder type, workpiece material, and process stability. For turning stainless steels under steady conditions, the T6215 grade offers a cost-effective balance of wear resistance and edge life. When process variations or heavy interruptions are expected, opting for a different chipbreaker or a larger corner radius may be advisable. Consult the technical drawing of the insert pocket and the holder’s clearance specifications to confirm fit and to ensure cutting parameters are matched to the insert’s capabilities. For application advice on Tungaloy T6215 inserts or to check stock and delivery options, contact Metav Werkzeuge for tailored recommendations and rapid support at info@metav-werkzeuge.com or +49 2822 7131930 Technical data Article number: 6903122 SKU: 6903122-Tungaloy Model series: ISO-Drehwendeschneidplatten Designation: TCMT16T302-PS Material: carbide Core specifications Shape: triangular Size: 16 Thickness: 3.97 mm Corner radius: 0.2 mm Included angle: 60° Clearance angle: 7° Design and features Coating: CVD Grade: T6215 Chipbreaker: PS Hole: with hole Hole style: cylindrical hole + single-side countersink (40°–60°) Typical application: turning (external and internal) FAQ What materials is this insert intended for? This Tungaloy indexable turning insert in grade T6215 is intended primarily for machining stainless steels under stable to slightly interrupted cutting conditions. How is the insert fixed to the holder? The insert uses a central cylindrical hole with a single-side countersink (40°–60°) for secure clamping in compatible indexable holders; ensure holder matches the ISO form and tolerance class. What does the PS chipbreaker do? The PS chipbreaker helps produce controllable chip forms when turning stainless steels, improving evacuation and coolant access during cutting with the T6215 insert. Which corner radius and included angle does the insert have? The insert features a 0.2 mm corner radius and a 60° included angle, offering a balance between edge strength and surface finish capability. Can this insert be used for interrupted cuts? Yes—this insert and grade are suitable for stable to slightly interrupted cutting; for severe interruptions, consider a different geometry or a larger radius. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
TCMT 16T302 T9215 Wendeplatten - Tungaloy
Take advantage of the combination of CVD-coated T9215 grade, a precise 0.2 mm corner radius and ISO compatibility for stable, productive turning of medium steels; order the TCMT16T302-PS insert directly via Metav Werkzeuge or ask our consultants if needed. TCMT16T302-PS T9215 ISO turning insert — CVD-coated carbide, triangle 60° (Tungaloy) A TCMT16T302-PS indexable turning insert engineered for external and internal turning of medium steels, offering robust wear resistance and predictable chip control. CVD-coated T9215 grade for mid-range steels Triangle 60° form with 0.2 mm corner radius 7° clearance, 3.97 mm thickness Cylindrical hole with one-sided 40°–60° countersink Delivering consistent productivity for medium-steel turning The insert is supplied in a CVD-coated cemented carbide grade (T9215) that balances wear resistance and fracture toughness, which directly supports longer tool life during continuous and slightly interrupted cuts. Selecting this specification reduces unscheduled changeovers and maintains consistent component tolerances, so machining cycles remain predictable. The combination of a coated carbide substrate and a chipbreaker tuned for steel processing contributes to efficient chip formation and evacuation, improving throughput on CNC lathes while reducing the risk of built-up edge. Precision geometry that supports repeatable component quality With a triangle 60° configuration and a 0.2 mm corner radius, the geometry offers a compromise between strength at the cutting edge and the ability to produce tight radii on external profiles. The 7° clearance angle reduces rubbing and lowers cutting forces in most turning operations, promoting a stable cutting zone and extending insert life. The plate thickness of 3.97 mm and ISO conformity ensure compatibility with standard ISO toolholders; this makes integration into existing tool systems straightforward and supports rapid tool changes with predictable seating and clamping behaviour. Compatibility and mounting details for reliable set-up The insert includes a cylindrical central hole with a single-sided countersink (40°–60°) for positive clamping in standard ISO-compatible holders; compatibility is determined by form, clearance angle, tolerance class, fastening method, size and thickness. When pairing with an appropriate external holder or boring bar, the insert system—comprising the indexable plate, support shim and clamping set—delivers repeatable positioning and secure retention under varying cutting loads. This mechanical reliability minimises vibration and supports surface finish consistency across batches. Why the PS chipbreaker and grade selection matter in practice The PS chipbreaker is designed for turning operations in steels where reliable chip control and continuous cutting are priorities; it helps form short, manageable chips in typical feed and speed ranges for medium steels. Grade T9215 performs as a first choice for general steel machining by combining a CVD coating with a substrate engineered for high productivity, offering a cost-effective balance between wear life and edge robustness. For shops aiming to increase spindle time while maintaining dimensional stability, this insert is a practical option that aligns process security with efficient material removal. Choose the TCMT16T302-PS from Tungaloy for dependable mid-steel performance and contact Metav Werkzeuge for availability and application advice — eMail: info@metav-werkzeuge.com | Tel: +49 2822 7131930 Technical data Article number: 6774068 Facts Manufacturer SKU: 6774068-Tungaloy Internal SKU: TUN6774068 ISO designation: 16T302 Plate size: 16 mm Plate thickness: 3.97 mm Corner radius: 0.2 mm Clearance angle: 7° Insert angle: 60° Special features Coating / grade: T9215 (CVD-coated cemented carbide) Chipbreaker: PS Plate form: triangular Hole: cylindrical hole with one-sided countersink (40°–60°) Application: turning (external and internal) Series: ISO turning indexable inserts FAQ What materials is this insert intended for? This insert is optimised for medium steels; the T9215 CVD-coated carbide grade and PS chipbreaker deliver wear resistance and chip control suitable for typical steel turning operations. Will the insert fit existing ISO toolholders? Compatibility depends on holder form, clearance angle and dimensions; the TCMT16T302-PS follows ISO specifications (16T302) and is designed for use with standard ISO-compatible external holders and boring bars. How does the PS chipbreaker affect machining? The PS chipbreaker promotes short, controllable chips in continuous to lightly interrupted cuts, improving evacuation and reducing rework related to chip entanglement. Is the corner radius suitable for finishing passes? The 0.2 mm corner radius provides a balance between strength and the ability to produce fine radii; it is suitable for many finishing and semi-finishing operations, depending on feed and cutting parameters. What are the key benefits of the T9215 grade? Grade T9215 combines CVD coating and a robust substrate to offer a compromise of high wear resistance and fracture toughness, supporting higher productivity in steady cutting conditions. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
TCMT 16T302 T9225 Wendeplatten - Tungaloy
Take advantage of a CVD‑coated carbide grade T9225 and a PS chipbreaker designed for interrupted cuts to achieve reliable mid‑to‑heavy steel turning with stable chip control; order the TCMT16T302‑PS T9225 Tungaloy turning insert directly via Metav Werkzeuge or consult our specialists for process support. TCMT 16T302 T9225 turning insert (TCMT16T302-PS) – Tungaloy TCMT16T302-PS T9225 Tungaloy insert is a triangular ISO turning insert intended for medium to heavy steel turning where toughness and consistent chip control are required. ISO‑standard triangular insert TCMT 16T302 CVD‑coated carbide grade T9225 for robust cutting PS chipbreaker optimised for interrupted cuts 7° relief and 60° included angle for stable engagement Reliable cutting under varying engagement The CVD‑coated T9225 grade delivers a balance of wear resistance and toughness that suits medium to heavy steel machining. The coating reduces flank and crater wear while the substrate maintains fracture resistance when cuts are slightly interrupted or engagement varies. This combination makes the insert particularly suitable where workpiece conditions change or roughing passes alternate with semi‑finishing; the result is predictable tool life and fewer unplanned indexings. Fast setup and secure clamping for consistent results As an ISO format triangular insert, compatibility is determined by form, relief angle, tolerance class, fastening and plate thickness. The TCMT form with size 16 and thickness 3.97 mm installs in standard holders without modification. The cylindrical hole with one‑sided countersink (40°–60°) ensures reliable clamping and repeatable seating, reducing vibration and supporting consistent surface finish when paired with a correctly matched holder. Controlled chips and process stability for interrupted cuts The PS chipbreaker is engineered to control chip formation during external and internal turning, particularly where cut interruptions occur. By guiding and segmenting chips, the breaker reduces risk of entanglement and improves evacuation in deeper cuts. Use the plate’s corner radius 0.2 mm for lighter finishing passes or to maintain dimensional accuracy when turning small radii; for heavier passes, the combination of chipbreaker and robust grade helps maintain cutting edge integrity. Productivity through durability and simple selection Choosing this triangular, indexable insert simplifies tool inventory by providing a universal option for a range of steel applications. The CVD coating enhances wear resistance, while the tougher substrate resists chipping under variable engagement, which together support longer intervals between indexing and predictable replacement cycles. Select the PS chipbreaker and the T9225 grade when a compromise between machining speed and edge security is needed. Discuss application requirements with Metav Werkzeuge to confirm the TCMT16T302‑PS Tungaloy insert is the best fit for the machining task and secure tailored recommendations—email info@metav-werkzeuge.com or call +49 2822 7131930 to proceed Technical Data Article number: 6781065 Manufacturer SKU: TUN6781065 Brand: Tungaloy Model series: ISO turning inserts Product designation: TCMT16T302‑PS T9225 Material: carbide Coating / grade: T9225 (CVD‑coated) Facts Size: 16 Thickness: 3.97 mm Corner radius: 0.2 mm Relief angle: 7° Included angle: 60° Hole style: cylindrical hole + one‑sided countersink (40°–60°) Special features Triangular plate, with hole PS chipbreaker ISO‑standard insert Suitable for medium to heavy steel turning Compatible with ISO external holders CVD‑coated carbide grade for wear resistance FAQ Which materials is this insert suited for? The TCMT16T302‑PS T9225 insert is specified for medium to heavy steel machining and performs well where toughness is needed under varying engagement. Is the chip control suitable for interrupted cuts? Yes, the PS chipbreaker on the TCMT16T302‑PS is designed to manage chips effectively during interrupted and semi‑stable cuts. What are the key dimensions to check when selecting a holder? Confirm size 16, thickness 3.97 mm, relief angle 7° and the cylindrical hole with countersink match the intended ISO holder for proper seating of the TCMT plate. Can this insert be used for internal turning? The insert form and chipbreaker allow internal turning where holder geometry and process stability are suitable; ensure the holder provides correct clearance and clamping for the TCMT format. How does the T9225 grade affect tool life? The T9225 CVD‑coated grade balances wear resistance and toughness, improving edge security and delivering more predictable tool life under mid‑to‑heavy cutting conditions. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
TCMT 16T304 AH6225 Wendeplatten - Tungaloy
Take advantage of a universally applicable, PVD-coated carbide grade for consistent performance and easy integration into ISO tooling systems; the insert combines a sharp, stable cutting edge with reliable chip control for medium-duty turning. Order directly via Metav Werkzeuge or request advice from the technical consultants for application-specific recommendations. TCMT 16T304 AH6225 – Triangular ISO turning insert for medium-duty rostfreier Stahl machining by Tungaloy A TCMT 16T304 AH6225 insert for ISO-compliant external and internal turning, offering a 60° geometry and a PVD-coated carbide grade tuned to deliver a sharp yet robust cutting edge under variable conditions PVD-coated carbide grade AH6225 ISO triangular 60° geometry, 16 mm size 0.4 mm corner radius for precise profiles Cylindrical hole with 40°–60° countersink Consistent metal removal with reduced wear The combination of the AH6225 grade and a PVD-coated carbide substrate provides a balance between edge sharpness and wear resistance, making the insert especially effective for medium cutting depths in rostfreier Stahl. The coating reduces thermal and abrasive wear, which translates into more consistent tool life and fewer interruptions for index changes. With a 0.4 mm corner radius, the geometry supports accurate profile reproduction while maintaining sufficient edge strength for intermittent cuts; the one-sided chipbreaker enhances chip formation and evacuation, improving process stability and surface finish. Secure fit and repeatable clamping for predictable results Designed as an ISO-standard triangular insert, the item matches holders when form, clearance, tolerance class, fastening, size and thickness align. The 60° included angle and 7° clearance angle ensure compatibility with a wide range of external and internal turning holders, while the cylindrical hole with single-sided countersink (40°–60°) enables stable mechanical clamping and straightforward index changes. A plate thickness of 3.97 mm and a nominal size of 16 mm support rigidity in most workshop setups, reducing vibration and promoting repeatable cutting conditions across batches. Flexible choice for practical workshop applications For everyday turning tasks, the insert’s combination of PVD coating, carbide core and a dedicated chipbreaker makes it a versatile option for shops seeking a single grade that covers several rostfreier Stahl applications. Select the chipbreaker and insert geometry according to workpiece material, machining strategy and machine stability to maximise productivity; in mixed-production environments, this approach shortens setup times and simplifies tooling inventories. The solution supports an efficient workflow by offering durable cutting performance with minimal compromise on surface quality. For tailored advice on selecting Tungaloy turning inserts and to discuss compatibility with specific holders, contact Metav Werkzeuge at info@metav-werkzeuge.com or call +49 2822 7131930 — consultants are available to assist with application-specific recommendations Technical data Article number: 6829874 Manufacturer SKU: TUN6829874 SKU: 6829874-Tungaloy Brand: Tungaloy Model series: ISO-Drehwendeschneidplatten Material: Hartmetall Grade/coating: AH6225, PVD-coated Numbers / Core technical data Size: 16 mm Thickness: 3.97 mm Corner radius: 0.4 mm Clearance angle: 7° Included angle: 60° Hole/countersink: cylindrical hole + single-sided countersink 40°–60° Designs / Special features Triangular plate form One-sided chipbreaker ISO-standard insert designation TCMT16T304 With hole for secure clamping Suited for rostfreier Stahl machining Universal grade for medium machining and variable conditions FAQ Which materials is this insert suited for? The TCMT 16T304 AH6225 insert is formulated for machining rostfreier Stahl and performs well across a range of austenitic and similar alloys when used under recommended parameters. What is the effect of the 0.4 mm corner radius? A 0.4 mm corner radius balances profile accuracy and edge strength, allowing the insert to produce defined contours while resisting premature chipping during medium-duty turning. Which holders are compatible with this ISO insert? Compatibility depends on holder form, clearance, tolerance class, fastening, size and thickness; the ISO 60° triangular geometry and the cylindrical hole with countersink ensure fitment with standard ISO triangular turning holders designed for 16 mm inserts. What advantages does the AH6225 PVD coating provide? The AH6225 grade with a PVD coating enhances wear resistance and thermal stability, extending usable edge life and improving consistency in surface finish during medium cutting operations. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
TCMT 16T304 AH6225 Wendeplatten - Tungaloy
Take advantage of a PVD-coated carbide grade that balances a sharp, stable cutting edge with broad applicability for rostfreier Stahl; the ISO conformity ensures straightforward tool changes and consistent process reliability. Order supply or consult Metav Werkzeuge's specialists for application support and availability. TCMT 16T304 AH6225 – ISO turning insert by Tungaloy (PVD-coated carbide, 0.4 mm corner radius) TCMT16T304 AH6225 is a triangular ISO turning insert designed for external and internal turning applications, optimised for rostfreier Stahl and medium machining tasks. PVD-coated carbide for high wear resistance Optimised for rostfreier Stahl turning One-sided chipbreaker for controlled chips Triangular ISO insert with 0.4 mm corner radius Reliable cutting performance for consistent production The combination of a PVD-coated carbide substrate and the AH6225 grade delivers a balance between a sharp cutting edge and edge stability, which directly improves process consistency. This chemistry and coating support longer tool life under variable conditions and reduce unscheduled tool changes, thereby improving machine uptime. For shops working with rostfreier Stahl, the insert’s robustness helps maintain dimensional accuracy and surface finish over longer tool cycles. Design choices that simplify setup and compatibility Supplied as an ISO-standard triangular insert, the geometry (16 mm size, 60° included angle) and the 0.4 mm corner radius provide predictable cutting engagement and robust strength at the corner. The insert is finished with a cylindrical hole and a single-sided countersink (40°–60°) for secure mounting; compatibility with toolholders is determined by form, clearance angle, tolerance class, fastening arrangement, size and thickness. The 7° clearance angle allows reliable chip formation while protecting the cutting edge in interrupted cuts. Chip control and process efficiency The single-sided chipbreaker is engineered to stabilise chip flow during turning, improving surface quality and reducing the risk of chip entanglement. Better chip control reduces cycle interruptions and cleaning time at the machine, which leads to measurable productivity gains. Choosing the appropriate chipbreaker and the AH6225 grade for medium machining of rostfreier Stahl supports consistent cutting forces, which in turn helps to extend insert life and reduce tooling costs per component. Practical selection and handling advice Select the insert in combination with a matching holder and clamping set to ensure correct seat and stable engagement; the ISO standardisation of the insert simplifies cross-referencing and replacement. For best results, match the cutter geometry and the chipbreaker style to the material condition and the machining parameters. Store inserts in their original packaging to protect the cutting edges, and inspect mounting screws and the backing pad for wear when making replacements to maintain repeatable performance. For precise turning of rostfreier Stahl with Tungaloy quality, request application guidance or stock availability from Metav Werkzeuge via info@metav-werkzeuge.com or call +49 2822 7131930 — Metav Werkzeuge can advise on holder compatibility and supply. Technical data Article number: 6829883 SKU (supplier): TUN6829883 Our SKU: 6829883-Tungaloy Name: TCMT16T304 AH6225 Tungaloy insert Model series: ISO turning inserts Specifications Insert size: 16 mm Thickness: 3.97 mm Corner radius: 0.4 mm Clearance angle: 7° Included angle: 60° Hole style: cylindrical hole + single-sided countersink (40°–60°) Special features Material: carbide Coating / grade: AH6225 (PVD-coated) Shape: triangular ISO insert Chipbreaker: one-sided for controlled chips Application: external and internal turning, medium machining of rostfreier Stahl Compatibility: ISO-conforming insert for matching holders, clamping sets and screws FAQ What materials is this insert suited for? This insert is designed primarily for machining rostfreier Stahl; the AH6225 PVD-coated carbide grade offers broad applicability for medium turning tasks in that material. How does the chipbreaker affect performance? The one-sided chipbreaker on the TCMT16T304 AH6225 insert improves chip formation and evacuation, resulting in better surface finish and fewer interruptions during turning. Is the insert compatible with standard ISO holders? Yes, the insert follows ISO geometry; compatibility depends on matching form, clearance angle, tolerance class, fastening, size and thickness to the holder. What mounting features should be checked before use? Ensure the cylindrical hole and single-sided countersink align with the holder’s clamping system, and verify that the seating surface and screws are in good condition to maintain stability. Can this insert be used for both external and internal turning? Yes, the insert is suitable for both external and internal turning operations when paired with an appropriate toolholder and stable machining setup. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
Fragen zu diesen Produkten??
Mit mehr als 30 Jahren Erfahrung beraten wir Sie gerne persönlich.
Tel.: +49 2822 7131930
Mail: info@metav-werkzeuge.com