TNGA 160416 LX10 Wendeplatten - Tungaloy
Take advantage of the combination of robust carbide construction, ISO compatibility and a balanced R1.6 corner radius for steady performance and reduced downtime; order the TNGA160416 LX10 Tungaloy indexable insert directly via Metav Werkzeuge or consult our specialists for application-specific advice. TNGA 160416 LX10 indexable turning insert — 60° triangular, Tungaloy The TNGA160416 LX10 is a triangular ISO indexable insert designed for external and internal turning, delivering a balance of wear resistance and edge stability for a wide range of lathe operations. ISO 60° triangular geometry Tungaloy LX10 carbide grade Corner radius R1.6 mm Cylindrical hole for secure clamping Improved productivity through optimised cutting performance The LX10 grade, produced by Tungaloy, combines carbide substrate properties with a formulation geared to deliver stable cutting-edge performance. This results in enhanced wear resistance and consistent tool life, which lowers the frequency of insert changes and reduces unscheduled downtime. For production environments that prioritise throughput and repeatability, the engineering of this grade supports higher workpiece counts before regrinding or replacement is necessary. The geometry and edge quality contribute directly to consistent cycle times and reliable surface finish. Reliable fitment and precise engagement with ISO tooling Manufactured to ISO dimensions, the insert’s 60° included angle and triangular profile ensure compatibility with standard 60° turning toolholders. The cylindrical hole and matching clamping interfaces permit secure fixation in the holder, reducing micro‑movement under cutting forces. With a plate thickness of 4.76 mm and a nominal size of 16 mm, the component integrates seamlessly into typical indexable systems; this reduces setup time and simplifies inventory management for mixed-production shops that rely on ISO tooling standards. Balanced edge geometry for controlled cutting behaviour The modest corner radius (R1.6) offers a compromise between edge strength and the ability to achieve fine surface finishes. A larger radius supports higher feed rates and improved edge durability, while the chosen value here retains good cutting control for semi-finishing passes. The insert is supplied without a chipbreaker, permitting selection of the most suitable chip control strategy for the workpiece material and machining conditions. This flexibility allows process engineers to tune feed and depth of cut for maximum economy or for the highest achievable surface quality. Practical handling and system-level advantages on the shop floor As part of an ISO turning insert system, the component is intended to be used with a matching external holder or boring bar, plus the appropriate clamping kit and replacement fastening screws. The triangular shape provides three usable cutting edges per index, improving cost-efficiency per edge compared with single-edge tools. The LX10 formulation complements the mechanical design by combining toughness and wear resistance, helping to maintain process stability across varied turning tasks and to reduce the need for frequent insert inventory changes. For tailored recommendations on using Tungaloy turning inserts and for availability, contact Metav Werkzeuge—email info@metav-werkzeuge.com or call +49 2822 7131930 for technical guidance and rapid supply. Technical data Article number: 6852202 Manufacturer SKU: TUN6852202 SKU: 6852202-Tungaloy Series: ISO turning indexable inserts Manufacturer: Tungaloy Core data Corner radius: R1.6 mm Included angle: 60° Thickness: 4.76 mm Size: 16 mm ISO designation: 160416 Features Triangular insert Cylindrical hole Grade: LX10 Material: carbide Chipbreaker: none Application: turning ISO compatibility with 60° holders FAQ What toolholders are compatible with this insert? The TNGA160416 LX10 insert is designed to fit ISO 60° triangular holders and standard external turning toolholders that accept a 16 mm triangular insert and a cylindrical hole clamping system. Can this insert be used for both external and internal turning? Yes, the insert is intended for both external and internal turning applications when mounted in the appropriate holder or boring bar; selection of the holder and cutting parameters influences performance. What is the advantage of the LX10 grade? The LX10 grade provides a balance of wear resistance and toughness, offering extended life under typical turning conditions and stabilised cutting-edge behaviour for repeatable results. Is a chipbreaker included on the insert? This designation is supplied without a chipbreaker, allowing the process engineer to choose a chip control solution matched to the workpiece material and machining strategy. How many cutting edges are available per insert? The triangular geometry offers three indexed cutting edges per insert, improving the cost-efficiency of the insert package. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
TNGA 160416 LX11 Wendeplatten - Tungaloy
Take advantage of the combination of ISO-compliant geometry, balanced LX11 cutting grade and a secure clamping design for consistent turning performance; order directly via Metav Werkzeuge or ask our consultants for application-specific advice. TNGA160416 LX11 triangular turning insert — ISO turning insert, 60°, Tungaloy A TNGA160416 LX11 indexable insert engineered for external and internal turning in ISO tool systems, offering balanced wear resistance and reliable edge stability. ISO-compliant triangular insert LX11 grade for balanced wear resistance 1.6 mm corner radius for versatile turning Cylindrical hole for secure clamping Consistent cutting performance with a balanced cutting grade The insert combines a modern LX11 carbide grade with a triangular form that delivers predictable wear progression and robust cutting-edge behaviour. Designed for general turning applications, the geometry and material mix aim to extend effective tool life while preserving surface integrity. Thanks to the 1.6 mm corner radius and the 60° main angle, the component supports a broad range of turning tasks where controlled chip formation and dependable edge stability are required. ISO compatibility for easy tool system integration Designed to the ISO turning insert family, this product ensures replaceability across standard tool holders when form, clearance angle, tolerance class, fastening method, size and thickness match. The ISO-compliant specification simplifies tooling logistics and reduces setup time. Key dimensions such as 16 mm size, 4.76 mm thickness and the cylindrical hole support secure seating and repeatable positioning in clamping systems, helping to maintain process stability and reproducible results. Practical versatility for external and internal turning The insert is suitable for both external and internal turning operations where a robust, general-purpose grade is preferred. With no integral chipbreaker, the selection encourages pairing the insert geometry with the holder’s chip control solution appropriate to the workpiece material and cutting conditions. The tungsten carbide substrate provides the necessary hardness and toughness balance to cope with variable cutting loads while supporting consistent material removal. Designed for productivity and reliable machining By combining a modern grade with standardised geometry and a secure clamping interface, the insert supports efficient workshop workflows and predictable scheduling. The specification reduces the need for frequent insert changes and simplifies inventory management by aligning with ISO toolholder standards. Built for industrial turning, the design emphasises stable cutting edges, repeatable mounting and therefore contributes to overall productivity and process confidence. Contact Metav Werkzeuge for tailored advice on integrating the Tungaloy TNGA160416 LX11 insert into production processes or to request application-specific recommendations via info@metav-werkzeuge.com or by phone at +49 2822 7131930 Technical data Article number: 6808112 Manufacturer article number: 6808112 SKU: 6808112-Tungaloy Manufacturer SKU: TUN6808112 Manufacturer: Tungaloy Model series: ISO turning inserts Dimensions & measurements Insert size: 16 mm Thickness: 4.76 mm Corner radius: 1.6 mm Main angle: 60° Clearance angle: 0° Hole: cylindrical Design & special features Material: carbide Grade: LX11 Form: triangular Chipbreaker: none Application: turning Compatibility depends on form, clearance angle, tolerance class, fastening, size and thickness FAQ What types of turning operations suit this insert? This insert is intended for general external and internal turning; the TNGA160416 LX11 insert by Tungaloy performs well where a balanced wear resistance and edge stability are required. How does the LX11 grade affect tool life? The LX11 grade on the TNGA160416 provides a compromise between wear resistance and toughness, promoting longer effective tool life under variable cutting conditions. Which holders are compatible with this ISO insert? Compatibility is determined by the holder’s form, clearance angle, tolerance class, fastening and the insert’s size and thickness; the TNGA160416 mates with holders that accept ISO triangular inserts of the specified dimensions. Is a chipbreaker included with the insert? This triangular insert is supplied without an integrated chipbreaker, allowing chip control to be managed via the holder geometry or process parameters when using the TNGA160416 LX11. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
TNGA 160416 TH10 Wendeplatten - Tungaloy
Take advantage of a robust combination of carbide construction, a 60° triangular geometry and a sharp uncoated grade for efficient turning with low cutting forces; order genuine Tungaloy inserts directly via Metav Werkzeuge or consult our specialists for process matching. TNGA 160416 TH10 triangular indexable turning insert – Tungaloy, sharp uncoated carbide, 60° main angle TNGA160416 TH10 is an ISO‑standard turning insert designed for general external and internal turning where a sharp, uncoated cutting edge supports low cutting forces and clean surface finishes ISO triangular insert, 60° cutting edge Uncoated carbide for low cutting forces Cylindrical centre hole for secure clamping Suitable for external and internal turning Higher productivity through lower cutting forces The uncoated carbide composition of this insert reduces friction at the cutting edge, which translates into lower cutting forces and improved energy efficiency during turning operations. For shops machining non‑ferrous materials or applications that benefit from a keen, uncoated edge, the insert promotes steady material removal and helps maintain spindle loads within predictable limits. The sharp geometry also supports clean surface finish, reducing the need for secondary processes in many cases. Easy integration into existing tool systems Designed to the ISO‑standard, the triangular geometry and 60° angle ensure predictable fitment with appropriate external holders and boring bars. Compatibility depends on form, relief angle, tolerance class, fastening, size and thickness; the listed dimensions and centre‑hole style facilitate straightforward selection of a matching clamp or screw, enabling rapid tool changes and short setup times. This leads to fewer interruptions on the shop floor and a more consistent production flow. Grade benefits: TH10 for universal non‑ferrous performance The TH10 grade is an uncoated, sharp universal variant optimised for non‑ferrous materials and situations where an uncoated cutting edge improves chip formation and workpiece quality. In practice this means less rubbing, reduced tendency for built‑up edge and reliable surface results when machining aluminium alloys, brass or other softer metals. The absence of a chipbreaker suits applications where uninterrupted chip flow or manual chip control is preferable. Practical handling and application guidance With a 1.6 mm corner radius and 4.76 mm thickness, the insert offers a balance between edge strength and the ability to achieve fine finishes. The cylindrical centre hole ensures secure clamping in standard ISO tool seats; when combined with an appropriate clamping plate and screw, the system affords repeatable positioning and stable cutting conditions. For best results, match the insert geometry and the TH10 grade to material, feed and stability of the setup. For reliable replacement inserts and application advice, order authentic Tungaloy parts via Metav Werkzeuge or contact our technical consultants at info@metav-werkzeuge.com or +49 2822 7131930 for selection support Technical data Article number: 6808113 SKU: 6808113-Tungaloy Manufacturer SKU: TUN6808113 Model series: ISO‑turning inserts Facts Geometry: triangular, 60° Corner radius: 1.6 mm Insert size: 16 mm Thickness: 4.76 mm Relief angle: 0° Hole: with cylindrical hole Special features Grade: TH10 (uncoated) Material: carbide Application: turning (external and internal) Chipbreaker: none ISO designation: TNGA160416 Compatibility determined by form, relief angle, tolerance, fastening, size and thickness FAQ What materials is this insert best suited for? The TNGA160416 TH10 insert from Tungaloy is best suited for non‑ferrous materials such as aluminium and brass, and for applications where an uncoated, sharp edge produces cleaner surfaces. Can this insert be used for both external and internal turning? Yes, the ISO triangular TNGA160416 insert is designed for both external and internal turning when paired with the appropriate holder or boring bar. How does the TH10 grade affect tool life and finish? The TH10 uncoated grade promotes low cutting forces and improved chip control in softer materials; it offers good surface finish while preserving a sharp edge, though overall life depends on cutting parameters and stability. Is a chipbreaker included on this insert? This specific insert is supplied without a chipbreaker, which is suitable for processes that require unobstructed chip flow or where external chip control is applied. What fastening style does the insert require? The insert features a cylindrical centre hole for secure clamping; compatibility with the holder is determined by form, tolerance class, fastening type, size and thickness. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
TNGA 220408 TH10 Wendeplatten - Tungaloy
Benefit from the TNGA220408 TH10's sharp, uncoated carbide grade and its 0.8 mm corner radius for low cutting forces and clean surface results; its ISO conformity and triangular form ensure wide holder compatibility and straightforward tool integration. Order the insert directly via Metav Werkzeuge or consult the team for application advice. TNGA 220408 TH10 TNGA ISO-220408 turning insert, uncoated carbide by Tungaloy TNGA220408 TH10 is an ISO-standard indexable insert intended for external and internal turning, optimised for non-ferrous materials and low-force finishing operations Uncoated carbide TH10 for low cutting forces Triangular 22 mm insert with 60° included angle 0.8 mm corner radius for clean surface finish ISO-compliant insert with cylindrical hole Improved finishing and lower cutting forces for non-ferrous work The uncoated carbide grade TH10 delivers a consistently sharp cutting edge that reduces cutting forces and helps achieve a superior surface finish when machining non-ferrous materials. With a 0.8 mm corner radius, the geometry supports smooth chip flow and localised cutting conditions that are favourable for fine external profiles and light finishing passes. This combination makes the insert particularly suitable where low thermal load and minimal burr formation are priorities. Fast integration into ISO tool systems for efficient set-up Designed as an ISO-compliant insert, the triangular 22 mm form and cylindrical hole simplify compatibility checks with standard external holders and boring bars. The 60° included angle and a plate thickness of 4.76 mm ensure mechanical stability while allowing multiple indexed edges for cost-effective machining cycles. Clear identification of form, clearance angle and size reduces set-up time and supports repeatable clamping and alignment in production environments. Predictable performance and straightforward material choice Made from cemented carbide, this grade is deliberately left uncoated to favour low cutting resistance and to preserve a sharp edge for clean cuts on aluminium, brass and similar alloys. The absence of an integrated chipbreaker means the application relies on selecting the correct holder geometry and cutting parameters; this allows precise tailoring of cutting conditions to achieve the best finish and tool life in light-duty turning and fine profiling operations. Guidance for selection and process reliability When selecting an insert for turning tasks, consider the workpiece material, the required surface quality and the machine–tool rigidity. The triangular geometry provides three usable cutting edges per index, supporting economical replacement cycles. The TNGA220408 TH10 performs best where the process calls for low cutting forces and a clean, sharp edge rather than heavy interrupted cuts or hard materials. For operations requiring greater edge protection or higher wear resistance, a coated grade would be an alternative to evaluate. Contact Metav Werkzeuge for tailored advice on integrating the TNGA220408 TH10 into existing tool holders or to confirm suitability for specific turning tasks Technical data Article number: 6808114 SKU: 6808114-Tungaloy Manufacturer SKU: TUN6808114 Model series: ISO-Drehwendeschneidplatten Application: Turning Facts Inscribed circle / size: 22 mm Thickness: 4.76 mm Corner radius: 0.8 mm Included angle: 60° Clearance angle: 0° Manufacturer article number: 6808114 Special features Material: Carbide (cemented carbide) Grade: TH10 (uncoated) Plate form: Triangular Hole: With cylindrical hole Chipbreaker: None Typical use: External and internal turning; suited to non-ferrous materials FAQ What materials is this insert best suited for? The TNGA220408 TH10 insert, an uncoated carbide grade from Tungaloy, is optimised for non-ferrous materials such as aluminium and brass where low cutting forces and clean surfaces are required. How many cutting edges are available per insert? The triangular form provides three usable cutting edges; the TNGA220408 TH10 can be rotated to a fresh edge as each becomes worn. Does the insert include a chipbreaker? This variant is supplied without a chipbreaker, so the TNGA220408 TH10 relies on holder geometry and cutting parameters for chip control. What size and thickness does the insert have? The insert has an inscribed circle of 22 mm and a thickness of 4.76 mm, with a 0.8 mm corner radius and a 60° included angle. Which holders are compatible with this ISO insert? ISO compatibility depends on matching the triangular form, hole style and size; the TNGA220408 TH10 features a cylindrical hole and standard ISO indexing that suits many external and boring holders. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
TNGG 110302 NS9530 Wendeplatten - Tungaloy
Take advantage of the combination of NS9530 cermet finishing grade, precise 60° triangular geometry and a 0.2 mm corner radius for reliable, high-quality turning results. Order the insert directly via Metav Werkzeuge or ask the consultants for machining recommendations and availability. TNGG 110302 NS9530 triangular turning insert (cermet, finishing) – Tungaloy TNGG 110302 NS9530 is an ISO‑standard triangular turning insert designed for finishing operations in steel; compatible with standard ISO holders when matched for form, clearance and clamping Cermet NS9530 for fine finishing 60° triangular geometry for stable cutting 0.2 mm corner radius for high surface quality 3.18 mm thickness for secure clamping Superior surface finish from a finishing cermet The NS9530 grade is an uncoated cermet developed for finishing steels, delivering a sharp cutting edge and low cutting forces. For operations requiring a fine surface and consistent part form, this material choice reduces the tendency to build-up edge and improves reproducibility. The insert is optimised for continuous cutting and small depths of cut, which means a predictable finish and reduced need for downstream polishing in many turning processes. Repeatable seating and secure clamping in ISO systems A stable toolholder interface is essential for precision turning. The triangular insert geometry (60°) and the 3.18 mm plate thickness provide a rigid support surface, while the cylindrical hole ensures positive location in holders designed for inserts with a hole. Compatibility with a given holder depends on the insert form, clearance angle, tolerance class, fastening method, size and thickness, so matching the insert to the holder secures repeatability and reduces vibration during cuts. Lower cutting forces for consistent finishing performance The 0.2 mm corner radius balances edge strength with a fine cutting contact, keeping cutting forces low and helping to maintain small feed and depth settings typical of finishing passes. This geometry assists in reducing chatter and improves surface integrity on turned steel components, providing the tangible benefit of fewer rejected parts and improved process stability in serial production. Easy integration into production workflows This ISO‑standard insert fits into a common system build: an ISO insert, an appropriate external holder or boring bar, a support pad/clamp set and replacement screws. The chipbreaker 01 and the NS9530 grade should be selected in accordance with workpiece material, machining style and machine stability. For shops standardising on finishing operations, the insert offers straightforward stocking and fast changeover, contributing to efficient production planning. Contact Metav Werkzeuge for tailored application advice and availability of Tungaloy finishing inserts; email info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: 6997819 Manufacturer SKU: TUN6997819 SKU: 6997819-Tungaloy Designation: TNGG110302-01 NS9530 Model series: ISO-Drehwendeschneidplatten Material: cemented carbide Facts Inscribed circle / size: 11 mm Thickness: 3.18 mm Corner radius: 0.2 mm Included angle: 60° Clearance angle: 0° Hole: cylindrical Special features Grade: NS9530 (uncoated cermet) Application: Turning (external and internal) Chipbreaker: 01 Insert shape: triangular Mounting: with cylindrical hole Compatibility criteria: form, clearance, tolerance class, fastening, size, thickness FAQ What applications is this insert best suited for? The TNGG 110302 NS9530 insert is designed for finishing turning operations, providing high surface quality in steel when used for continuous cuts and small depths of cut. Can this insert be used for internal and external turning? Yes, the triangular geometry and available holders make the insert suitable for both external and internal turning, provided the correct holder and clamping are selected. How does the 0.2 mm corner radius affect performance? A 0.2 mm radius reduces cutting forces and helps to produce a finer surface finish, while still offering enough edge robustness for finishing passes on steel. Which holders are compatible with this ISO insert? Compatibility depends on the holder’s form, clearance angle, tolerance class, fastening method, size and the insert thickness; holders designed for triangular ISO inserts with a cylindrical hole will accept this type. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
TNGG 110304 GT9530 Wendeplatten - Tungaloy
Benefit from the combination of GT9530 coated cermet for extended wear resistance and the ISO-standard TNGG110304-01 triangular insert with a 0.4 mm corner radius and 60° geometry for reliable finishing performance; order directly via Metav Werkzeuge or consult the advisers for machining recommendations. TNGG 110304 GT9530 Tungaloy turning insert — ISO triangular cermet, 0.4 mm radius A TNGG110304-01 GT9530 ISO triangular turning insert designed for finishing to light universal turning of steel where good surface quality and longer tool life are required. ISO triangular insert TNGG form, 60° geometry GT9530 coated cermet for longer tool life 0.4 mm corner radius for fine surface finish Cylindrical hole mounting, compatible with holders Precision finishing with consistent surface quality The ISO triangular indexable insert delivers repeatable surface finish in stable turning operations. The GT9530 coated cermet grade combines a wear-resistant coating with a cermet substrate to reduce flank wear and improve edge stability during finishing passes. With a 0.4 mm corner radius the insert supports low cutting forces and finer chip segmentation, resulting in reduced vibration and a measurable improvement in surface roughness. This makes the solution particularly suitable where consistent dimensional accuracy and surface integrity are priorities. Secure clamping and compatibility for efficient tool changes Designed to ISO standards, the insert features a cylindrical hole and standard geometry that ensure secure clamping and straightforward indexing in compatible external holders or boring bars. The 60° insert form and defined thickness of 3.18 mm provide mechanical stability under light to moderate cutting loads; the standardised interface reduces set-up time and minimises the risk of misalignment during exchange. Clear compatibility criteria—form, relief angle, tolerance class, fastening, size and thickness—ensure that the insert integrates reliably into established tool systems. Practical grade selection and application benefits The coated cermet grade is optimised as a wear-resistant finishing to light universal grade for steel machining, offering an effective balance between surface finish and tool life in stable cutting conditions. For users aiming to improve throughput and component quality, the insert reduces downtime related to frequent edge changes and supports productivity gains through longer insert intervals. Where higher stability or interrupted cuts are present, a corresponding chipbreaker or different grade may be selected to match process demands. Contact Metav Werkzeuge for tailored recommendations on insert selection, compatible holders and cutting data for Tungaloy turning solutions; request detailed machining parameters via info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: 6997771 Manufacturer SKU: TUN6997771 SKU: 6997771-Tungaloy Model series: ISO-Drehwendeschneidplatten Facts Corner radius: 0.4 mm Geometry: 60° Thickness: 3.18 mm Size: 11 (inscribed circle) Hole: with cylindrical hole Chipbreaker: 01 Special features Grade: GT9530 Cutting material: coated cermet Shape: triangular insert Application: turning (finishing to light universal) Compatibility: ISO-standard insert interface Mounting: cylindrical-hole fastening, suitable for standard holders FAQ What materials is this insert recommended for? The TNGG110304-01 GT9530 insert is designed primarily for steel machining, offering a wear-resistant coated cermet suited to finishing and light universal turning operations. How does the GT9530 grade affect tool life compared with standard grades? GT9530’s coated cermet composition improves wear resistance and edge stability, extending useful life in stable turning conditions compared with uncoated cermet or standard carbide grades. Is the insert compatible with standard ISO external holders? Yes, the ISO-standard triangular form and cylindrical hole allow installation in compatible external holders and boring bars that accept TNGG-format inserts. What benefit does the 0.4 mm corner radius provide? A 0.4 mm corner radius balances edge strength and low cutting forces, improving surface finish while reducing the risk of vibration during finishing passes. Which chipbreaker is supplied with this insert? The insert is supplied with chipbreaker designation 01, suitable for finishing and controlled chip formation in appropriate steel turning applications. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
TNGG 110304 GT9530 Wendeplatten - Tungaloy
Benefit from the GT9530 coated cermet grade for extended tool life and consistently improved surface finish, combined with the ISO triangle form that ensures compatibility with standard turning holders; order the insert directly via Metav Werkzeuge or consult the team for application advice. TNGG 110304 GT9530 Turning Insert — Tungaloy triangle insert, 60° TNGG110304-01 GT9530 is a triangle indexable turning insert designed for finishing to light general-purpose turning, offering high wear resistance under stable cutting conditions Coated cermet GT9530 for long tool life Triangle form with 60° included angle 0.4 mm corner radius for fine finishing Cylindrical hole for secure clamping Improved surface finish with controlled wear The combination of a coated cermet grade and a fine 0.4 mm corner radius delivers a superior surface on turned parts while extending the time between indexings. Cermet is a ceramic–metal composite that combines hardness and toughness; applied here as GT9530, it offers low adhesive wear and maintains cutting-edge integrity during finishing cuts. For workshop managers seeking fewer interventions and more consistent finishes, this insert reduces rework and supports predictable batch quality. Compatibility and secure mounting for reliable cycles Designed to the ISO indexable insert standard, the triangular geometry with a cylindrical hole ensures repeatable seating and straightforward interchange with compatible external holders or boring bars. The 60° included angle provides a balance between access and strength for external and internal turning. Clear form, clearance angle and dimensional tolerances govern compatibility, so selecting a matching holder based on shape, size and thickness is decisive for process reliability. Application focus: finishing and light universal turning in steel This grade is tailored for turning operations where a fine surface and extended life are priorities under stable conditions. The coated cermet excels on steel where low cutting forces and moderate feeds are used; it is particularly suited to finishing passes and light universal applications. By choosing the appropriate chipbreaker and grade combination, machinists gain improved surface integrity with fewer tool changes, translating directly into more efficient production cycles. Practical benefits and process guidance Using a graded indexable insert like this reduces downtime through predictable wear behaviour and consistent chip formation. Select the 01 chipbreaker and the GT9530 grade when the workpiece material and machine rigidity support finishing cuts; this pair promotes stable chip evacuation and prevents irregular edge degradation. For best results, pair the insert with a holder that matches the plate size and thickness to maintain clamping stability and repeatability. For tailored advice on integrating Tungaloy GT9530 inserts into existing workflows, contact Metav Werkzeuge: info@metav-werkzeuge.com or call +49 2822 7131930 — the Metav Werkzeuge team is ready to recommend the optimum combination for specific turning applications. Technical data Article number: 6997772 SKU: 6997772-Tungaloy Manufacturer SKU: TUN6997772 Designation: TNGG110304-01 GT9530 Facts Included angle: 60° Corner radius: 0.4 mm Plate thickness: 3.18 mm Plate size: 11 mm Special features Material: carbide Grade/coating: GT9530 (coated cermet) Plate form: triangle Chipbreaker: 01 Hole: with cylindrical hole Application: Turning Series: ISO indexable turning inserts FAQ What materials is this insert best suited for? This insert, specified in the TNGG110304-01 GT9530 listing, is optimised for turning steel in finishing and light universal operations thanks to the GT9530 cermet grade. How does the GT9530 coating affect tool life? The GT9530 coating improves wear resistance and reduces adhesive wear on the cutting edge, extending tool life for finishing passes compared with uncoated grades. Is the insert compatible with standard ISO holders? Yes; the insert is an ISO-format triangle indexable insert and is compatible with holders that match the plate form, size, thickness and clamping style. What cutting tasks suit the 0.4 mm corner radius? A 0.4 mm radius is ideal for fine finishing and light turning where a clean surface and tight tolerances are required, while avoiding excessive cutting forces. Does the cylindrical hole affect clamping stability? The cylindrical hole provides central fixation for repeatable seating and secure clamping when used with the correct clamping screw and seat geometry. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
TNGG 110304 NS9530 Wendeplatten - Tungaloy
Take advantage of a finishing-grade cermet NS9530 and the ISO‑compatible triangular form for reliable, high‑quality turning results; the insert delivers low cutting forces and an excellent surface finish while fitting standard ISO holders. Order directly via Metav Werkzeuge or consult our application specialists for selection advice. TNGG 110304 NS9530 – Tungaloy turning insert (ISO triangular, 60°, finishing grade) TNGG 110304 NS9530 is an ISO‑standard triangular turning insert designed for external and internal turning, engineered as a finishing grade for steel with a sharp cutting edge and low cutting forces. Finishing cermet grade NS9530 Sharp cutting edge for low cutting forces ISO‑standard triangular insert, 60° included angle 0.4 mm corner radius for fine surface finish High‑precision finishing with a cermet grade designed for steel The insert is produced as an uncoated cermet (NS9530) finishing grade, which is specified for low cutting forces and an improved surface quality when turning steel. Cermet combines ceramic hardness with metallic toughness; this composition reduces built‑up edge and supports a sharp cutting edge that is particularly effective in continuous turning operations. For finishing passes and small depths of cut, the result is a consistently finer surface and reduced secondary operations. ISO compatibility that simplifies tool setup and reduces downtime Designed to the ISO turning insert standard, the component integrates smoothly into established triangular insert systems. Compatibility is determined by insert form, clearance angle, tolerance class, fixing method, size and thickness; the triangular geometry with a 60° included angle and a 3.18 mm plate thickness ensures secure clamping in many common holder designs. This standardisation shortens changeover times and helps maintain repeatable set‑ups across production runs. Process stability and recommended use cases for consistent results The grade is optimised for continuous cuts and small depths, where the sharp edge and material pairing reduce cutting forces and promote stable chip formation. Selecting the correct chipbreaker and matching the grade to workpiece stability are decisive for achieving the anticipated tool performance. When applied as intended, the insert supports consistent turning quality and helps to avoid surface defects that would otherwise require reworking. Practical selection tips for reliable integration into production Choose the insert variant with the chipbreaker code and tolerance suitable for the workpiece and machining conditions; the presence of a cylindrical hole facilitates positive clamping and indexable replacement. The item is supplied in the ISO‑compliant format and can be referenced by manufacturer article number for procurement and stock control. For finishing operations on steel where a fine part finish is required, this insert represents an efficient choice within a standard triangular insert system. For precision finishing with Tungaloy’s NS9530 cermet insert, contact Metav Werkzeuge for availability, application guidance and part confirmation at info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: 6997827 Manufacturer article number: 6997827 Manufacturer SKU: TUN6997827 Model series: ISO turning indexable inserts ISO designation: TNGG110304-01 Facts Corner radius: 0.4 mm Plate thickness: 3.18 mm Plate size: 11 mm Included angle: 60° Clearance angle: 0° Shape: triangular Special features Grade: NS9530 (uncoated cermet) Finishing grade for steel with sharp cutting edge Application: turning (external and internal) Chipbreaker: 01 Hole: with cylindrical hole for clamping Designed for continuous cuts and small depths FAQ What steel applications suit this insert best? The TNGG 110304 NS9530 insert is specified as a finishing grade for steel; it is best used where low cutting forces and a fine surface finish are required, for continuous turning and small depths of cut. Is the insert compatible with standard ISO triangular holders? Yes. The insert follows ISO dimensions for triangular turning inserts; holder compatibility is governed by form, clearance angle, tolerance class, fixing method, size and thickness. What does the NS9530 designation indicate? NS9530 denotes an uncoated cermet grade tailored for finishing operations on steel, offering a sharp edge geometry and stable performance in continuous cuts. How does the 0.4 mm corner radius affect the machining result? A 0.4 mm corner radius helps achieve a smoother part surface while maintaining acceptable strength at the cutting edge for finishing passes. Can this insert be used for internal turning as well as external turning? Yes. The TNGG 110304 NS9530 insert is suitable for both external and internal turning when the appropriate holder and machining parameters are selected. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
TNGG 110304 NS9530 Wendeplatten - Tungaloy
Take advantage of the combination of a sharp cermet cutting edge, low cutting forces and ISO compatibility for reliable finishing on steel components; order the insert directly via Metav Werkzeuge or contact our consultants for tailored advice. TNGG110304-01 NS9530 triangular ISO turning insert by Tungaloy — uncoated cermet, 60° cutting angle A TNGG110304-01 NS9530 indexable turning insert engineered for finishing operations on steel, offering a sharp cutting edge and low cutting forces for superior surface quality. Uncoated cermet for high surface finish Triangular ISO insert, 60° cutting angle 0° relief for continuous finishing cuts Suitable for external and internal turning Enhanced surface quality for finishing cuts The uncoated cermet grade NS9530 is formulated for finishing operations on steel, delivering a sharp cutting edge and reduced friction at the tool–workpiece interface. This results in lower cutting forces, which helps to limit workpiece distortion and to achieve consistent surface roughness even on sensitive geometries. For shops seeking predictable part quality, the finishing grade reduces secondary operations and supports tighter tolerances. Clear guidance on compatibility and clamping As an ISO-format triangular insert, compatibility with a toolholder depends on form, clearance angle, tolerance class, fastening method, size and thickness. The insert is a triangular shape with a 60° included angle, 0° relief, and a 0.4 mm nose radius, with a cylindrical locating hole for positive locating. In a standard system the insert is used together with a matching external holder or boring bar, an underlay/clamping set and replacement screws; this modular approach simplifies inventory management and reduces setup time. Improve process stability and predictability The uncoated cermet chemistry and the fine edge geometry make the grade particularly suitable for continuous cuts and small depths of cut, where a clean shear and steady chip formation are key. Selecting the correct chipbreaker (type 01 in this case) and adapting the holder rigidity to the application stabilises the cutting process and prolongs tool life. The combination of a stable cutting edge and low cutting forces contributes directly to higher first-pass yields and reduced rework. Practical selection and application recommendations For external and internal turning of steel components, choose this insert when surface finish and dimensional control are priorities. Match the chipbreaker and grade to the stock material, machining method and machine-tool rigidity for best results. Where interrupted cuts or heavy roughing are required, prefer more robust grades; for final passes and finishing, this insert delivers an efficient compromise between surface quality and tool economy. For expert selection of Tungaloy finishing inserts and to source items quickly, contact Metav Werkzeuge for technical support and availability – Metav Werkzeuge will advise on matching holders and application parameters. Technical data Manufacturer item number: 6997820 SKU: 6997820-Tungaloy Manufacturer SKU: TUN6997820 Article designation: TNGG110304-01 NS9530 Tungaloy insert Core specifications Insert size: 11 Thickness: 3.18 mm Cutting angle: 60° Nose radius: 0.4 mm Clearance (relief) angle: 0° Hole: cylindrical Chipbreaker: 01 Features & applications Uncoated cermet grade NS9530 Material: carbide substrate with cermet cutting surface Application: turning (external and internal) ISO triangular insert format Designed for finishing of steel Compatibility determined by holder form, clearance angle, tolerance class, fastening, size and thickness FAQ What machining operations is this insert intended for? This insert is designed for turning operations; the NS9530 grade and triangular ISO form suit finishing passes on steel, for both external and internal turning. How does the NS9530 cermet grade affect surface finish? The NS9530 uncoated cermet provides a sharp cutting edge and reduced cutting forces, which together produce a finer surface finish and more consistent part quality when used for finishing cuts. What holder features are required for correct fitment? Fitment depends on holder form, clearance angle, tolerance class, fastening type, size and thickness; the insert uses a cylindrical locating hole and requires a clamping set compatible with ISO triangular inserts. Can this insert be used for interrupted cutting? This grade is optimised for continuous finishing and small depths of cut; for frequent interrupted cuts a tougher grade or alternative geometry is generally recommended. Which manufacturers produce compatible holders and accessories? Compatible holders and accessories are available from standard tooling suppliers; Metav Werkzeuge can advise on specific holder models that match the insert dimensions and clamping requirements. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
TNGG 110304 NS9530 Wendeplatten - Tungaloy
Data inconsistency detected — the item is simultaneously described as carbide and as an uncoated cermet, which are distinct material types; please verify the product specification to ensure accuracy, as such discrepancies can lead to confusion or errors in selection, application, or performance evaluation, particularly when precise material properties are critical for the intended use or operational requirements, and it is essential to confirm whether the description aligns with the actual composition, manufacturing standards, and intended functionality of the product to avoid potential misunderstandings or issues in procurement, usage, or quality assurance processes that rely on accurate and consistent information.
TNGG 110308 GT9530 Wendeplatten - Tungaloy
Take advantage of the combination of wear-resistant coated cermet, precise 60° triangular geometry and secure clamping for steady finishing performance in turning operations; order directly via Metav Werkzeuge or request expert advice from our consultants to ensure optimal tool-holder pairing. TNGG 110308 GT9530 Tungaloy — ISO triangular indexable insert for turning A TNGG110308-01 GT9530 indexable insert designed for ISO-compliant external and internal turning, delivering fine surface finish and extended tool life under stable machining conditions Coated cermet grade GT9530 for excellent finish ISO triangular insert, 60° geometry 0.8 mm corner radius for fine finishing Cylindrical through-hole for secure clamping Consistent fine finishing through a wear-resistant grade The core advantage of this insert is its coated cermet composition (GT9530) which prioritises surface quality and tool life. In practical terms, the ceramic-metal matrix of the coating reduces flank wear and maintains edge integrity during finishing passes. This leads to fewer interruptions for indexation or insert changes, supporting a more continuous production flow. For turning applications where a high-quality surface is required under steady clamping conditions, the grade delivers measurable benefits in productivity and part consistency. Geometry and clamping that ensure repeatable performance Engineered as a triangular insert with 60° geometry and a cylindrical hole, the component provides reliable seating and orientation in ISO holders. The 0.8 mm corner radius balances edge strength and the ability to produce fine profiles, making it suitable for light finishing and semi-finishing tasks. The ISO conformity means compatibility depends on holder form, clearance angle and tolerance class; selecting a holder with matching parameters ensures the insert’s mechanical advantages convert directly into process stability and repeatable workpiece quality. System considerations and straightforward integration The insert is part of an ISO indexable turning system: the full setup typically includes the ISO insert, a compatible external holder or boring bar, and suitable clamping elements and screws. Its 3.18 mm thickness and size designation align with standard seat geometries, simplifying inventory and tool-change procedures. Chipbreaker selection (chipbreaker 01 in this case) and matching the grade to the workpiece hardness are decisive for optimised chip control and thermal behaviour. Clear identification of these variables reduces setup time and supports a predictable machining cycle. Direct benefits for workshop efficiency and process reliability Adopting this insert supports two primary outcomes: higher surface quality per pass and longer intervals between insert changes, which together lower non-productive time and contribute to cost-efficient production. The combination of GT9530 coating and robust seat geometry is particularly effective when machining steel in stable fixtures. For teams seeking predictable finishing performance with straightforward holder compatibility, the insert provides a pragmatic balance of precision and endurance. Contact Metav Werkzeuge for tailored advice on holder compatibility and to arrange supply of the TNGG 110308 GT9530 insert Technical data Article number: 6997774 Manufacturer SKU: TUN6997774 Model series: ISO indexable turning inserts Facts Insert angle: 60° Thickness: 3.18 mm Corner radius: 0.8 mm Size: 11 Special features Coating/grade: GT9530 Cutting material type: coated cermet Insert shape: triangular Hole style: cylindrical through-hole Chipbreaker: 01 Clearance angle: 0° Intended application: turning (external and internal) Compatibility: ISO-compliant system seating FAQ What materials is this insert best suited for? The GT9530 grade is designed as a wear-resistant coated cermet primarily for machining steel under stable conditions, offering improved surface finish and extended tool life compared with uncoated grades. How is compatibility with tool holders determined? Compatibility depends on form, clearance angle, tolerance class, fastening method, size and thickness; the ISO designation and 60° triangular geometry inform the correct holder selection for secure seating. What advantage does the GT9530 coating provide? The GT9530 coating enhances wear resistance and thermal stability, allowing the insert to sustain fine finishing passes longer and maintain consistent part quality before indexation is required. Why choose a 0.8 mm corner radius for finishing? A 0.8 mm corner radius offers a compromise between cutting-edge strength and the ability to achieve a refined surface texture, making it suitable for light finishing where dimensional control and surface appearance matter. Which chipbreaker is fitted and what is its role? This insert uses chipbreaker 01; the designated chipbreaker assists in producing short, controllable chips under the recommended machining conditions, improving surface integrity and process safety. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
TNGG 110308 GT9530 Wendeplatten - Tungaloy
Take advantage of the combination of a GT9530 cermet coating, a 0.8 mm corner radius and ISO conformity for precise finishing and prolonged tool life — ideal for stable steel turning operations; order the insert directly via Metav Werkzeuge or consult our specialists if guidance is required. TNGG 110308 GT9530 triangular ISO turning insert by Tungaloy — finishing and light‑universal steel turning A TNGG110308-01 GT9530 indexable insert designed for ISO‑compliant turning operations, offering a cermet coating for improved surface finish and extended wear resistance in stable machining conditions GT9530 cermet coating for improved wear resistance 0.8 mm corner radius for fine finishing results ISO‑compliant triangular insert, 60° included angle 3.18 mm thickness with cylindrical central hole Higher surface quality with predictable tool life The GT9530 grade is a cermet-based, coated option optimised for finishing to light‑universal machining of steel. Its composition and coating chemistry reduce flank wear and improve edge stability, meaning fewer interruptions for index changes and a more predictable tool life. In practical terms, a coated cermet substrate delivers a smoother contact between tool and workpiece, which translates into consistently superior surface finish and reduced rework. The combination of a fine 0.8 mm corner radius and the hard wearing coating supports low‑vibration cuts where dimensional consistency matters. Designed for ISO tool systems and straightforward integration Compatibility is defined by form, clearance angle, tolerance class, fastening, size and thickness; the triangular ISO geometry and 60° included angle of this insert allow straightforward interchangeability with standard holders. The plate’s 3.18 mm thickness and cylindrical hole enable secure clamping and repeatable seating in appropriate tool bodies. For workshop planning, the insert integrates into established tool assemblies — an ISO‑compliant component that minimises setup variability and simplifies tool inventory management across turning platforms. Reliable chip control and application focus Equipped with chipbreaker code 01, the insert helps to produce stable chip forms in typical finishing feeds and depths for steel. This chip geometry reduces entanglement and supports continuous cutting at steady parameters, which is particularly beneficial on longer parts or when unattended running is required. The insert’s substrate, based on cemented carbide and enhanced by the cermet coating, favours finishing passes and light‑duty general‑purpose turning where a combination of wear resistance and surface quality is required rather than heavy interrupted cuts. Practical handling and selection advice for machinists Selection of the correct grade and chipbreaker depends on workpiece material, machining mode and machine stability. The triangular ISO plate shape provides three cutting edges per index, improving cost efficiency without compromising finish. Where precise edge geometry is important, the 0° clearance angle and the specified tolerances of the system ensure consistent seating; choosing the matching holder form and fastening hardware completes the assembly. Where additional data is needed for process planning, technical advisors can supply cutting parameter ranges based on machine power and setup rigidity. Contact Metav Werkzeuge for tailored advice on integrating Tungaloy GT9530 cermet inserts into production; call +49 2822 7131930 or email info@metav-werkzeuge.com to discuss holder compatibility and cutting data Technical data Article number: 6997773 Manufacturer SKU: TUN6997773 Supplier SKU: 6997773-Tungaloy Model series: ISO turning indexable inserts Product name: TNGG110308-01 GT9530 Tungaloy insert Facts Corner radius: 0.8 mm Plate thickness: 3.18 mm Plate size: 11 mm Included angle: 60° Clearance angle: 0° Chipbreaker: 01 Special features Coating/grade: GT9530 cermet coated Substrate material: cemented carbide Plate form: triangular Central hole: with cylindrical hole Application: turning (external and internal), finishing to light universal steel machining Compatibility: ISO‑compliant insert, fits matching ISO toolholders FAQ What materials is this insert best suited for? The TNGG110308-01 GT9530 insert is optimised for machining steel in finishing and light‑universal operations, where the GT9530 cermet grade offers improved surface finish and wear resistance. How is the chip formation managed with this insert? Chip formation is guided by the chipbreaker 01; the geometry promotes stable, controllable chips during finishing feeds and helps prevent entanglement on longer parts. What determines whether the insert will fit a holder? Compatibility depends on form, clearance angle, tolerance class, fastening method, size and thickness; ensure the holder matches the triangular ISO form, 60° included angle and 3.18 mm thickness. What edge radius and finish performance can be expected? The insert has a 0.8 mm corner radius, which supports fine finishing passes and contributes to a consistent surface quality when combined with the cermet coating. Is this product an original Tungaloy component? Yes, this is an original, brand‑new Tungaloy indexable insert produced to ISO specifications and supplied under the manufacturer’s article number 6997773. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
TNGG 110308 NS520 Wendeplatten - Tungaloy
Take advantage of the combination of high surface quality, stable wear behaviour and ISO compatibility to keep production consistent and efficient; order the insert directly via Metav Werkzeuge or consult our specialists for holder matching and process parameters. TNGG 110308 NS520 Tungaloy indexable turning insert TNGG110308-01 NS520 Tungaloy indexable insert is an ISO-standard triangular insert for precision turning, optimised for finishing to light machining of steel where surface finish and dimensional accuracy are priorities Triangular ISO profile for robust clamping Cermet grade NS520 for fine surface finish 0° relief for stable turning performance Consistent finishing performance for steel components The TNGG110308-01 insert is specified for finishing and light cutting of steel and is supplied in the NS520 cermet grade, a coated cermet designed to deliver an excellent balance between wear resistance and surface quality. Its material combination supports a uniform wear pattern, which reduces the need for frequent insert changes and helps maintain dimensional stability across batches. For manufacturers aiming to reduce rework and improve first-pass yield, this grade provides a predictable tool life and reproducible results under stable cutting conditions. ISO compatibility and secure clamping reduce setup risks Designed as an ISO turning indexable insert, the triangular form and standardised dimensions make holder selection straightforward: compatibility depends on shape, relief angle, tolerance class, fastening and thickness. The insert features a cylindrical central hole and a defined seating geometry that ensure secure fastening in suitable external holders or boring bars. Using an insert that matches the holder by form and tolerance reduces the risk of improper clamping, vibration and inconsistent cutting, thereby supporting process reliability on the shop floor. Geometry tuned for surface finish and edge stability With an included angle of 60° and a corner radius of 0.8 mm, this insert balances edge strength and surface integrity. The relatively small corner radius helps achieve fine surface finishes while still providing sufficient edge support for light interruptions. The 0° relief (free angle) is appropriate for neutral cutting orientations and contributes to controlled cutting forces in finishing passes. Select the chipbreaker variant 01 to match typical steel machining conditions; it promotes predictable chip formation when paired with suitable feeds and speeds. Economic benefits through reduced downtime and predictable wear Cermet and coated cermet grades such as NS520 are particularly effective where surface quality and repeatability matter. The material’s resistance to adhesive wear and its ability to maintain an intact cutting edge under finishing parameters reduce machine downtime for insert changes and secondary operations. In practice this results in improved process throughput, less manual rework and a clearer cost-per-part calculation. For batch production and high-mix environments, the predictable performance of this insert supports stable planning and economical machining. For tailored holder recommendations or to secure Tungaloy quality for finishing operations, contact Metav Werkzeuge at info@metav-werkzeuge.com or call +49 2822 7131930 to discuss suitable holders and process settings for the TNGG110308-01 insert Technical data Article number: 6808124 SKU: 6808124-Tungaloy Manufacturer SKU: TUN6808124 Model series: ISO turning indexable inserts Core specifications Corner radius: 0.8 mm Insert size: 11 mm Thickness: 3.18 mm Relief angle: 0° Included angle: 60° Features & applications Material: carbide Grade: NS520 (cermet / coated cermet) Chipbreaker: 01 Hole style: cylindrical hole Shape: triangular Application: turning Typical use: finishing to light machining of steel FAQ What machining tasks is this insert intended for? The TNGG110308-01 NS520 Tungaloy indexable insert is intended primarily for finishing and light turning of steel, offering improved surface finish and tight dimensional control. Which materials can be machined with this grade? The NS520 cermet grade is tailored for steel machining; it provides good surface integrity and uniform wear when used under finishing conditions on steel workpieces. How does the triangular form affect holder selection? Holder compatibility is determined by insert form, relief angle, tolerance class, fastening, size and thickness; the triangular ISO profile ensures easy matching with standard external holders or boring bars designed for this geometry. What are the key geometric values to consider when planning cuts? Consider the 60° included angle and 0.8 mm corner radius for balancing edge strength and surface finish, and the 0° relief when selecting neutral cutting orientations and feeds. Is chip control supported for typical steel turning? Yes, the chipbreaker 01 variant is intended to promote controlled chip formation for finishing to light machining of steel when correct cutting parameters are applied. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
TNGG 110308 NS9530 Wendeplatten - Tungaloy
Conflicting product data detected: the specification lists both carbide and uncoated cermet as the cutting material, which creates ambiguity and makes it impossible to provide a reliable and accurate product description. This contradiction must be resolved to ensure clarity and consistency in the product details. Please confirm whether the insert is manufactured from carbide or from an uncoated cermet (NS9530), as this information is crucial for producing a complete, precise, and trustworthy listing that meets the necessary standards and expectations for accurate technical documentation and customer understanding. Without this clarification, the product description cannot be finalised or deemed reliable.
TNGG 110308 NS9530 Wendeplatten - Tungaloy
Take advantage of the combination of a sharp cermet cutting edge, low cutting forces and ISO compatibility for reliable finishing operations; order the insert via Metav Werkzeuge or consult the team for tailored application advice. TNGG 110308 NS9530 Tungaloy Turning insert, Finish turning TNGG110308-01 NS9530 is a triangular ISO turning insert designed for finish turning of steel with a sharp cutting edge and low cutting forces Finish-grade uncoated cermet NS9530 Low cutting forces for continuous turning Triangular ISO plate, 60° included angle Cylindrical hole, compatible with ISO holders Delivering consistent finish quality on steel The uncoated cermet NS9530 grade is engineered for finish operations on steel where a high surface finish and low cutting forces are essential. The geometry and sharp cutting edge of this ISO-standard insert promote smooth chip flow and minimise cut-induced vibrations, which reduces the need for secondary finishing. For applications with small depths of cut and continuous cutting conditions, the result is a reliable surface quality with reduced scrap rates and improved component consistency. Precision fit and predictable toolset integration The insert is an ISO-format triangular plate with a 60° included angle and a cylindrical hole, ensuring secure clamping in compatible holders. Key dimensions — size 11, thickness 3.18 mm and a corner radius of 0.8 mm — make the plate straightforward to specify for standard turning toolholders. The tolerance class, form and relief angle determine compatibility with the chosen holder; this standardisation simplifies inventory management and shortens setup times on production lines while maintaining repeatable cutting performance. Process advantages and operational economy Using a finish-grade cermet like NS9530 reduces cutting forces and helps to achieve finer surface finishes without extensive process adjustment. The combination of stable cutting behaviour and consistent edge condition supports longer intervals between insert changes in finish applications, contributing to cumulative cost savings and fewer interruptions. If there is uncertainty about matching the insert to a specific holder or machining condition, Metav Werkzeuge can supply application guidance and supplementary technical data to ensure the correct grade and chipbreaker selection. For finish turning with NS9530, contact Metav Werkzeuge for availability and application support tailored to your turning centre. Technical data Article number: 6997821 Manufacturer SKU: TUN6997821 SKU: 6997821-Tungaloy Model series: ISO-Drehwendeschneidplatten Data Size: 11 Thickness: 3.18 mm Corner radius: 0.8 mm Included angle: 60° Special features Grade: NS9530 Cutting material: uncoated cermet Plate form: triangular Hole: with cylindrical hole Application: Turning Series: ISO turning inserts Chipbreaker: 01 FAQ What materials is this insert intended for? This insert is specified as a finish-grade NS9530 cermet primarily for steel finishing operations; it is optimised for continuous cuts and small depths of cut. How does the plate locate in a holder? The triangular ISO plate uses the cylindrical hole and its form and clearance angle to fit standard ISO toolholders; compatibility depends on holder geometry and tolerance class. What benefits does NS9530 offer for finishing? The NS9530 grade delivers a sharp cutting edge, low cutting forces and a high surface finish, reducing rework and improving part consistency in finish turning. Which dimensions should be checked before ordering the insert? Confirm the size (11), thickness (3.18 mm) and corner radius (0.8 mm) against the intended holder and machining strategy to ensure correct fit and performance. Is this insert suitable for interrupted cuts? This finish-oriented cermet insert is optimised for continuous machining; for heavily interrupted cuts a different geometry or grade should be considered. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
TNGG 110308 NS9530 Wendeplatten - Tungaloy
Benefit from the combination of a sharp finishing grade, predictable triangle geometry and ISO compatibility for consistent surface quality and efficient production. Order the TNGG110308-01 NS9530 insert directly via Metav Werkzeuge or ask the consultants for holder compatibility and application advice. TNGG 110308 NS9530 triangular turning insert for turning, Tungaloy TNGG110308-01 is an ISO‑standard triangular insert engineered for precision finishing in steel turning, offering a low‑force cutting edge and a geometry tuned for continuous, fine cuts. Uncoated cermet finishing grade NS9530 Triangle geometry with 60° included angle Low cutting forces for high surface finish Cylindrical hole for secure clamping Achieve superior surface finish with an uncoated cermet grade The insert uses an uncoated cermet formulation (grade NS9530) designed specifically as a finishing grade for steel. This material provides a sharp cutting edge and low cutting forces, which together reduce built‑up edge and vibration during light cuts. The result is a consistently high surface finish on turned components and fewer rework cycles. For operations with continuous cutting and modest depths of cut, the combination of edge geometry and cermet wear characteristics supports longer intervals between indexings while maintaining dimensional stability. Predictable geometry for repeatable turning performance The triangle geometry with a 60° included angle and a radius 0.8 mm delivers defined contact conditions and stable chip flow. The insert thickness of 3.18 mm and the cylindrical hole ensure reliable clamping in ISO‑compatible holders and boring bars; tolerance class, relief angle and size determine exact holder compatibility. A 0° clearance provides the neutral relief needed for finishing passes where the holder setup and feed control govern the final result. This predictable geometry simplifies process planning and reduces trial cuts during setup. Integrate into existing turning systems to boost throughput With chipbreaker designation 01, the insert suits finishing strategies where chip control and small, continuous chip formation are required. The system approach — insert plus appropriate external holder or boring bar, shim/clamp and fastening screw — allows straightforward integration into standard tool posts. For operations prioritising surface integrity and efficiency, the insert supports stable turning cycles and consistent part quality. Metav Werkzeuge can advise on holder selection and recommended cutting parameters to optimise tool life and productivity with this grade. For precision finishing in steel turning with the NS9530 grade, contact Metav Werkzeuge for ordering and application consultancy; email info@metav-werkzeuge.com or call +49 2822 7131930 to discuss holder compatibility and process optimisation Technical data Article number: 6997829 SKU: 6997829-Tungaloy Manufacturer SKU: TUN6997829 Model series: ISO turning insert series Grade: NS9530 Material: carbide Facts Radius: 0.8 mm Included angle: 60° Clearance angle: 0° Thickness: 3.18 mm Size: 11 Hole: cylindrical hole Special features Triangle insert geometry Uncoated cermet grade NS9530 for finishing steel Chipbreaker style 01 Compatible with ISO holders and boring bars Intended for external and internal turning Suitable for continuous cuts and small depths of cut System: insert, external holder or boring bar, shim/clamp and spare screws FAQ What materials is the insert suitable for? The NS9530 grade is formulated as a finishing grade for steel, offering the sharp edge and low cutting forces needed for fine surface quality with the TNGG110308-01 insert (Tungaloy, SKU 6997829-Tungaloy). How does the NS9530 cermet differ from coated grades? NS9530 is an uncoated cermet finishing grade that prioritises a sharp edge and low cutting forces over hard coating wear resistance, making it ideal for continuous finishing cuts where surface finish is critical. Which holders are compatible with this ISO insert? Compatibility is determined by insert form, relief angle, tolerance class, fastening and size; the triangular ISO format of this insert fits ISO‑standard external holders and suitable boring bars when the holder matches the insert geometry and 3.18 mm thickness. What cutting strategy yields the best surface quality? Light finishing passes with controlled feed and stable clamping give the best results; the combination of low cutting forces and the insert’s geometry reduces vibration and built‑up edge, improving surface finish and repeatability. Can this insert be used for internal turning? Yes, the geometry and chip control characteristics make the insert suitable for both external and internal turning when paired with the correct boring bar and secure clamping. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
TNGG 160304 NS9530 Wendeplatten - Tungaloy
Order the TNGG160304 NS9530 insert for consistent finishing performance: the uncoated cermet NS9530 provides low cutting forces and superior surface finish, while the ISO triangular form with a 0.4 mm corner radius and 3.18 mm thickness ensures robust clamping and repeatable geometry; order via Metav Werkzeuge or consult the technical advisers for application matching. TNGG160304 NS9530 Tungaloy indexable insert for turning — ISO triangular finishing grade The TNGG160304 NS9530 is an ISO triangular indexable insert designed for turning applications, offering a finishing-grade, uncoated cermet cutting edge optimised for continuous cuts in steel. Triangle ISO form TNGG for stable clamping Sharp-edged uncoated cermet grade NS9530 Optimised for finishing and low cutting forces Cylindrical hole, 0° clearance for compatibility High-quality finishing with low cutting forces The uncoated cermet NS9530 is formulated as a finishing grade for steel, delivering a sharp cutting edge that reduces cutting forces and improves surface integrity. With an ISO triangular shape and a 60° included angle, the insert is suited to applications requiring precise dimensional control and excellent part appearance after a single pass. The 0° clearance angle and cylindrical hole contribute to simple, reliable mounting; compatibility with the toolholder is governed by form, relief angle, tolerance class, clamping method, size and thickness, so the correct holder selection is essential to achieve the advertised results. Geometry and operational advantages for production environments Featuring a 16 mm inscribed circle, 3.18 mm thickness and corner radius 0.4 mm, this triangular insert provides a balance between edge strength and the fine edge necessary for finishing work. The double-sided chipbreaker geometry supports controlled chip formation during continuous cuts and small depths of cut, lowering the likelihood of surface defects and reducing rework. Because the grade is uncoated, the insert gives consistent contact conditions on the tool edge, which helps maintain repeatable part quality and stable process parameters — a practical advantage when cycle-to-cycle consistency and surface finish are priorities. System compatibility, selection advice and application fit Delivered as an ISO-standard turning insert, the item forms part of a system comprising a matching external holder or boring bar, an underlay/shim and clamping set plus replacement screws. For best results, select the chipbreaker and grade to match the workpiece material and machining stability: the finishing NS9530 grade is particularly effective on steels in continuous turning with small depths of cut. The insert’s triangular form and central cylindrical hole allow simple indexing and secure clamping, supporting efficient tool changes and predictable positioning in automated or manual turning operations. Contact Metav Werkzeuge for tailored application advice and to order the TNGG160304 NS9530 insert; email info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: 6997830 Manufacturer SKU: TUN6997830 Model series: ISO-Drehwendeschneidplatten Label: TNGG160304 NS9530 Tungaloy-Wendeplatte Facts Inscribed circle: 16 mm Thickness: 3.18 mm Corner radius: 0.4 mm Included angle: 60° Clearance angle: 0° Hole: cylindrical Special features Material: carbide Cutting material grade: uncoated cermet NS9530 Plate form: triangular Chipbreaker: double-sided Mounting: with hole, compatible with ISO holders Typical application: turning, finishing, continuous cuts System components: matching external holder or boring bar, underlay/clamping set, replacement screws FAQ What materials is this insert intended for? The finishing-grade NS9530 uncoated cermet is designed primarily for machining steel, offering low cutting forces and an improved surface finish when used in continuous turning. How can compatibility with an existing toolholder be ensured? Compatibility depends on holder form, relief angle, tolerance class, clamping method, size and thickness; the ISO designation and the central cylindrical hole of the TNGG160304 aid straightforward matching with standard holders. What are the key geometric specifications to note? Important dimensions are a 16 mm inscribed circle, 3.18 mm thickness, 0.4 mm corner radius and a 60° included angle; the insert also features a 0° clearance angle and a cylindrical mounting hole. Is the insert coated or uncoated? This item is an uncoated cermet in grade NS9530, optimised for finishing applications where edge sharpness and surface quality are critical. Can this insert be used for roughing operations? The NS9530 grade and fine corner radius are optimised for finishing and small depths of cut; for heavy roughing or interrupted cuts, a more robust grade and geometry would be better suited. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
TNGG 160304 NS9530 Wendeplatten - Tungaloy
Conflicting product data: the material field specifies "Hartmetall" (cemented carbide), while the cutting material type is listed as "uncoated cermet" (NS9530). Please verify the correct substrate and grade before publishing the product description, as inconsistencies in the material information can lead to confusion for customers and potential issues with product performance, especially in applications where the specific properties of the material are critical. Ensuring accuracy in the product description is essential to maintain trust, avoid misunderstandings, and provide clear guidance to users regarding the suitability of the product for their intended use, particularly in industries where precision and reliability are paramount.
TNGG 160304 X407 Wendeplatten - Tungaloy
Take advantage of the ISO compatibility, robust X407 carbide grade and precise geometry for reliable turning performance. Combine predictable tool life with easy indexing for efficient production planning. Order the insert via Metav Werkzeuge or consult our technical team for application advice. TNGG160304 X407 Tungaloy insert — ISO turning insert for external and internal turning A TNGG160304 X407 triangular turning insert designed for ISO-standard holders, offering a balance of wear resistance and edge stability for general turning applications ISO-standard triangular insert, 60° geometry Carbide grade X407 for wear resistance Double-sided chipbreaker for efficient indexing Cylindrical hole and 0° relief for secure holder fit Fast integration into ISO-based tool systems The ISO-standard designation guarantees direct compatibility with holders and boring bars that accept the 160304 form; fit depends on form, 0° relief, tolerance class, fastening, size and thickness. This standardisation reduces setup time and supports consistent clamping repeatability on series production. Compatibility with existing tool systems simplifies inventory management and minimises downtime when replacing cutting edges. Material grade engineered for consistent wear and edge stability The carbide X407 grade from Tungaloy combines wear resistance and sufficient toughness to maintain a stable cutting edge under common turning conditions. This balance reduces flank wear and the risk of premature chipping, delivering more predictable tool life and fewer unscheduled indexings. The result is improved process reliability and a clearer cost-per-part calculation for production planning. Geometry that supports precision and surface quality The triangular plate form with a 60° included angle and a corner radius 0.4 mm provides a stable support area for radial forces and promotes consistent surface finish during both external and internal turning. A double-sided chipbreaker design enhances chip control and allows economical flipping of the insert, while the cylindrical hole and 3.18 mm plate thickness ensure secure seating in the clamping system. These geometric choices contribute directly to machining stability and repeatable results. Production benefits: predictable performance and efficient handling Indexed use of a double-sided insert reduces tooling costs per edge and eases logistical handling in the toolroom. The 16 mm plate size and the standardised designation simplify the selection of matching holders, shims and clamping kits as part of the ISO tool system. Fewer tool changes and consistent cutting behaviour increase machine availability and support steady production throughput while maintaining surface quality targets. Practical selection guidance for reliable machining Select the double-sided chipbreaker and X407 grade to match workpiece material, cutting parameters and machine rigidity; for unstable setups a tougher grade or a larger corner radius can improve robustness. The system comprises the insert, a suitable external holder or boring bar, a backing shim/clamping set and replacement screws, enabling quick replacement and secure clamping without complex adjustments. Ask Metav Werkzeuge for specific cutting data and availability of the Tungaloy TNGG160304 X407 insert — email info@metav-werkzeuge.com or call +49 2822 7131930 Technical Data Article number: 6808135 Manufacturer SKU: TUN6808135 Label: TNGG160304 X407 Tungaloy-Wendeplatte Material: Carbide Manufacturer: Tungaloy Data Insert designation: TNGG160304 ISO code: 160304 Angle: 60° Corner radius: 0.4 mm Thickness: 3.18 mm Plate size: 16 mm Special features Grade: X407 (Tungaloy carbide grade) Double-sided chipbreaker Cylindrical hole Triangular plate form 0° relief angle Application: turning FAQ What materials is this insert intended for? The TNGG160304 X407 insert is specified for general turning tasks; the X407 grade provides a balance of wear resistance and toughness suitable for a broad range of steels and general engineering materials. How does the insert sit in the holder and what ensures stability? Stability is ensured by the triangular 160304 form, the cylindrical hole and 3.18 mm plate thickness, which together secure the insert in the clamping seat of compatible ISO holders. Can the insert be indexed to use multiple cutting edges? Yes, the double-sided chipbreaker design permits economical indexing of the insert, allowing use of both faces to extend edge life and reduce tooling cost per edge. What is the corner radius and how does it affect finishing? The insert features a 0.4 mm corner radius, which supports improved surface finish and a balance between edge strength and cutting forces for many turning operations. Which SKU should be referenced when ordering or checking stock? Reference SKU 6808135-Tungaloy or manufacturer SKU TUN6808135 when enquiring about the TNGG160304 X407 Tungaloy turning insert Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
TNGG 160308 NS9530 Wendeplatten - Tungaloy
Combining the NS9530 finishing grade, an uncoated cermet cutting edge and a 60° triangular form, this insert delivers low cutting forces and superior surface finish; order the TNGG160308 directly via Metav Werkzeuge or consult the team for guidance. TNGG160308 NS9530 Tungaloy turning insert (ISO triangular, finishing) The TNGG160308 NS9530 is an ISO-standard triangular turning insert designed for finishing operations on steel, optimised for continuous cuts and small depths of cut. Finishing grade NS9530 cermet Sharp cutting edge for low cutting forces Triangle 60° form, 16 mm size Double-sided chipbreaker, cylindrical hole High-precision finishing with low cutting forces The combination of the NS9530 grade and an uncoated cermet edge is engineered for refined surface quality and consistent results in finishing turns. As a finishing insert it is particularly effective at maintaining a sharp cutting edge, which reduces required feed force and vibration. This leads to a measurable improvement in surface integrity and repeatability when machining steels at small depths of cut. The geometry promotes continuous chip formation where process stability is the priority, so the cutting action focuses on producing an excellent final surface rather than heavy material removal. Simple integration into ISO turning systems Designed as part of an ISO turning insert series, the component fits common external holders when form, relief angle, tolerance class, fastening method, size and thickness match. The 60° triangular shape with a nominal size of 16 mm and a plate thickness of 3.18 mm allows reliable clamping in standard toolholders; the cylindrical hole provides secure fastening. The double-sided chipbreaker extends usable life by permitting indexation of both cutting edges, supporting efficient tool-change routines and reduced tooling costs per component processed. Why the cermet grade benefits finishing on steel Cermet cutting grades are chosen for finishing because they retain a keen edge and produce a fine surface without excessive built-up edge. The uncoated formulation of this grade favours low cutting forces and attractive surface finishes on steels under continuous cutting conditions. The modest corner radius of 0.8 mm helps to balance edge strength with surface quality, limiting the risk of edge chipping while still allowing fine finishing passes. Manufactured by Tungaloy, the insert is intended for reliable, repeatable performance where surface specification and dimensional consistency matter most. For precision finishing on steel, contact Metav Werkzeuge to source the Tungaloy NS9530 insert and obtain expert selection advice at info@metav-werkzeuge.com or by phone on +49 2822 7131930 Technical data Article number: 6997833 Manufacturer SKU: TUN6997833 SKU: 6997833-Tungaloy Label: TNGG160308 NS9530 Tungaloy-Wendeplatte Model series: ISO-Drehwendeschneidplatten Facts Size: 16 mm Thickness: 3.18 mm Corner radius: 0.8 mm Included angle: 60° Clearance angle: 0° Hole style: cylindrical hole Grade: NS9530 Special features Uncoated cermet cutting grade NS9530 Double-sided chipbreaker ISO triangular insert form Suitable for external and internal turning Compatibility determined by form, relief angle, tolerance, fastening, size and thickness FAQ What materials is this insert intended for? The TNGG160308 NS9530 insert is formulated as a finishing grade for steels and performs best in continuous turning operations where high surface quality is required. Can the insert be indexed to use multiple edges? Yes, the double-sided chipbreaker allows the insert to be rotated and indexed to present fresh cutting edges, extending the productive life of each plate. What size and geometry should the toolholder have? A toolholder compatible with ISO triangular inserts with a 60° included angle, 16 mm nominal size and a 3.18 mm plate thickness is required to secure the TNGG160308 correctly. Is a coated grade available for heavier cuts? This offering is an uncoated cermet finishing grade; for heavier or interrupted cuts a different coated carbide or tougher grade should be selected based on application demands. How does the corner radius affect finish and strength? The 0.8 mm corner radius provides a compromise between edge strength and surface finish—small enough for fine finishes but sufficient to resist premature edge chipping under finishing feeds. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
TNGG 160308 NS9530 Wendeplatten - Tungaloy
Achieve reliable finishing on steel components with a sharp, low-force cutting action and a double-sided, ISO-compliant design; the combination of uncoated cermet cutting material and a 0.8 mm corner radius supports consistent surface quality and efficient production. Order the insert directly via Metav Werkzeuge or consult our specialists for application-specific advice. TNGG 160308 NS9530 TNGG160308 – Tungaloy indexable insert for Turning, uncoated cermet, 0.8 mm radius TNGG160308 NS9530 Tungaloy indexable insert for finishing operations in external and internal turning, designed as a triangular ISO insert for precision steel machining. Uncoated cermet for fine finishing Sharp cutting edge with low cutting forces Double-sided design with cylindrical hole ISO-compliant triangular insert for turning Superior finishing for steel components The uncoated cermet grade NS9530 provides a sharp cutting edge and low-chip formation, which together produce a high surface finish in continuous cut conditions. As a finishing grade developed for steel, this insert reduces the need for secondary grinding or polishing by delivering consistent micro-geometry on the workpiece. The low cutting forces inherent to the grade also help to maintain machine stability during small depth-of-cut operations, lowering the risk of chatter and dimensional deviation. Stable process and extended effective life A double-sided chipbreaker and a robust triangular geometry yield two usable cutting edges per index, improving economy without compromising consistency. The combination of 0.8 mm corner radius and a precisely formed cutting edge supports repeatable component quality while keeping cutting forces modest. For finishing cycles and small feed rates the result is a predictable turn-around time and reduced scrap rates, contributing to overall process reliability and productivity on production lines. Seamless integration into ISO tool systems Designed as an ISO-compliant turning insert, the part fits standard holders when matched by form, clearance, tolerance class, fastening method, size and thickness. The cylindrical hole ensures secure clamping, while the 3.18 mm plate thickness and 16 mm insert size suit a wide range of external and internal turning set-ups. With a nominal 60° cutting angle and 0° free angle, the geometry is optimised for finishing passes on shafts and bores where tight tolerances and excellent surface integrity are required. For precision finishing with Tungaloy’s NS9530 grade, contact Metav Werkzeuge for tailored application advice and to place orders — eMail: info@metav-werkzeuge.com | Tel: +49 2822 7131930 Technical Data Article number: 6997832 Manufacturer SKU: TUN6997832 Model series: ISO turning indexable inserts Material: Cemented carbide Grade: NS9530 Insert designation: TNGG160308 Facts Thickness: 3.18 mm Size: 16 mm Corner radius: 0.8 mm Cutting angle: 60° Free angle: 0° With hole: yes (cylindrical) Special features Uncoated cermet, finishing grade (NS9530) Double-sided chipbreaker Triangular insert form Compatible with ISO holders for external and internal turning Application: Turning; optimised for continuous cuts and small depth-of-cut finishing FAQ What materials is this insert best suited for? The TNGG160308 NS9530 insert is specified as a finishing grade for steel, offering a sharp edge and low cutting forces ideal for high-quality surface results. How many cutting edges are available per insert? The triangular, double-sided design provides two usable edges per side before indexing is required, improving cost-efficiency in finishing operations. Is this insert compatible with standard ISO turning holders? Yes. The insert designation and geometry follow ISO conventions; compatibility depends on matching form, clearance, tolerance class, fastening, size and thickness to the holder. What advantages does the NS9530 cermet grade offer? NS9530 is an uncoated cermet finishing grade that delivers low cutting forces and excellent surface integrity in continuous cuts and small feeds, reducing rework and improving first-pass yield. What is the part number and where can it be ordered? The article number is 6997832 and the manufacturer SKU is TUN6997832; orders and application enquiries can be directed to Metav Werkzeuge. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
TNGG 160400 NS9530 Wendeplatten - Tungaloy
Take advantage of the ISO‑standard triangular 60° geometry combined with the NS9530 uncoated cermet for consistently superior finishing on steel; the double‑sided chipbreaker and 4.76 mm plate thickness support stable, continuous turning with low cutting forces. Order directly via Metav Werkzeuge or consult our technical team for tailored holder compatibility and application advice. TNGG160400 NS9530 TNGG 160400 — Indexable turning insert for turning, Tungaloy TNGG160400 NS9530 is an ISO‑conforming triangular indexable turning insert designed for fine finishing of steel in turning applications, offering a sharp edge and consistent surface quality. ISO‑standard triangular insert 60° geometry Uncoated cermet NS9530 for fine finishing Double‑sided chipbreaker for continuous cuts 4.76 mm thickness with cylindrical hole Compatible with ISO turning toolholders Superior surface finish with reduced cutting forces The uncoated cermet NS9530 grade is formulated for finishing operations where a sharp cutting edge and low cutting forces are essential. Cermet materials combine ceramic hardness with metallic toughness, which reduces plastic deformation at the cutting edge and improves repeatable surface quality. For applications with small depths of cut and continuous feed, this geometry minimises built‑up edge and delivers a consistent, glossy finish on steel components, reducing the need for secondary processes. Stable chip control and repeatable performance A double‑sided chipbreaker combined with the triangular 60° geometry ensures predictable chip formation even in continuous cuts. The insert’s 4.76 mm thickness and cylindrical hole provide secure clamping and dimensional stability in the toolholder, which translates into less vibration and improved tool life. Stable chip control lowers the risk of edge damage and helps maintain tolerances across serial production, supporting efficient, cost‑effective machining cycles. Simple integration into ISO tool systems and selection guidance Built to ISO dimensions, this indexable insert guarantees compatibility based on form, clearance angle, tolerance class, fastening and thickness. Selection of the appropriate chipbreaker and grade should be guided by workpiece material, machining type and machine/fixture stability; for finishing steel the NS9530 grade and this insert form are an effective choice. For assistance matching insert, holder and process parameters, Metav Werkzeuge’s consultants can advise on the right combination for reliable, productive turning. For precision finishing with Tungaloy’s NS9530 cermet insert, contact Metav Werkzeuge for personalised selection and ordering — email info@metav-werkzeuge.com or call +49 2822 7131930 to speak with a specialist. Technical data Article number: 6997834 Manufacturer SKU: TUN6997834 Retail SKU: 6997834-Tungaloy Designation: TNGG160400 NS9530 Tungaloy‑indexable insert Model series: ISO turning indexable inserts Manufacturer: Tungaloy Facts Insert size: 16 mm Thickness: 4.76 mm Included angle: 60° Clearance angle: 0° ISO code: 160400 Hole: cylindrical Shape: triangular Special features Uncoated cermet grade NS9530 Designed for finishing of steel Double‑sided chipbreaker Suitable for continuous cuts and small depths of cut Compatibility with ISO toolholders determined by form and tolerance FAQ What applications is this insert best suited for? The TNGG160400 NS9530 indexable insert is intended for finishing operations in turning, particularly where low cutting forces and a high surface finish on steel are required. Is the grade coated or uncoated? The cutting material is an uncoated cermet (NS9530), optimised for sharp edges and fine finishing performance. Which holder types are compatible with this insert? Compatibility depends on ISO form, clearance angle, tolerance class, fastening, size and thickness; the insert follows ISO dimensions so it is compatible with standard ISO turning toolholders that accept triangular 16‑size inserts. How does the chipbreaker affect machining? The double‑sided chipbreaker supports stable chip formation during continuous turning, improving process security and reducing the likelihood of edge damage on long runs. Can this insert be used for roughing? This grade and geometry are specified as a finishing sort; for heavy roughing a different geometry and a tougher grade would typically be recommended. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand‑new product from the manufacturer.
TNGG 160400 NS9530 Wendeplatten - Tungaloy
Benefit from the NS9530 uncoated cermet grade and the sharp cutting edge to achieve superior surface finish with reduced cutting forces; the ISO‑compliant triangular 16 mm geometry with a 60° angle delivers fast indexability and consistent results — order the insert via Metav Werkzeuge or consult their specialists for application guidance. TNGG 160400 NS9530 Tungaloy indexable insert — finishing cermet for turning A TNGG160400 indexable turning insert in NS9530 cermet grade, optimised for finishing steel with low cutting forces and excellent surface quality. ISO‑standard triangular insert for turning NS9530 uncoated cermet for fine finishing Sharp cutting edge for low cutting forces Suitable for continuous cuts and small depths Precision finishing for demanding steel turning The uncoated cermet in grade NS9530 is tailored for finishing operations, producing a high surface finish while keeping low cutting forces. The microstructure of the cermet grade provides a keen, stable cutting edge that resists built‑up edge during continuous feed conditions. This results in consistent component quality when machining steels with small depths of cut, reducing the need for additional polishing or rework. ISO compatibility and consistent setup for efficient production Designed as an ISO‑normed indexable insert, the triangular geometry ensures quick replacement and repeatable positioning in standard holders. The ISO code and form compatibility mean the insert fits matched external holders or boring bars without custom modification. Key dimensions such as triangular size 16 mm, 4.76 mm thickness and the 60° included angle combine with a 0° clearance to deliver predictable cutting engagement and simplified tool inventory management, shortening setup time and supporting a steady production flow. Controlled chip behaviour and system benefits for productivity The insert is available double‑sided with a cylindrical mounting hole, enabling economical indexing and steady performance. Selecting the correct chipbreaker together with the grade will enable predictable chip control during continuous cutting, which supports unattended cycles and safer chip evacuation. The system approach — insert, matched holder, clamp and screws — promotes stable cutting conditions, improved surface integrity and efficient tool changeovers, translating into higher throughput and fewer interruptions on the shop floor. For finishing tasks on steel, choose the Tungaloy TNGG160400 NS9530 via Metav Werkzeuge for prompt availability and application advice from their technical consultants. Technical data Article number: 6997835 Manufacturer SKU: TUN6997835 SKU: 6997835-Tungaloy Model series: ISO-Drehwendeschneidplatten Insert designation: TNGG160400 NS9530 Facts Size: 16 mm Thickness: 4.76 mm Included angle: 60° Clearance angle: 0° Hole: with cylindrical hole Special features Material: carbide (cermet grade NS9530) Uncoated finishing grade for steel Double-sided triangular insert Suitable for continuous cut and small depths System requirement: compatible holder, clamp washer and screws FAQ What materials is this insert intended for? The TNGG160400 NS9530 insert is a finishing cermet designed primarily for machining steel, offering a balance of surface quality and low cutting forces. How does the NS9530 grade benefit finishing operations? NS9530 provides a sharp, wear‑resistant cutting edge that reduces cutting forces and improves surface finish during continuous cutting with small depths of cut. Is the insert reversible and economic to use? Yes, the triangular geometry is double‑sided, allowing multiple indexes per insert for cost‑effective usage and consistent performance. What holder types are compatible with this insert? Compatibility is determined by ISO form, clearance, tolerance, mounting and thickness; the insert is designed to fit standard ISO holders and boring bars with a cylindrical mounting hole. Can this insert improve cycle times on finishing passes? By combining a keen cermet edge with predictable chip behaviour, the insert helps maintain stable cutting conditions, supporting efficient finishing passes and fewer rework cycles. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
TNGG 160402 GH110 Wendeplatten - Tungaloy
High wear resistance and a balanced edge toughness deliver stable machining and longer tool life; the triangular geometry and secure cylindrical-hole clamping ensure repeatable positioning and fast index changes. Order the insert directly via Metav Werkzeuge or ask the consultants for tailored application support. TNGG160402 GH110 Tungaloy indexable insert for turning, triangular 60° main cutting edge TNGG160402 GH110 is a carbide indexable insert designed for external and internal turning in ISO-compatible holders, offering a compact triangular form with proven chip control. Triangular ISO insert TNGG160402, 60° included angle Carbide grade GH110 for wear resistance and edge stability Double-sided chipbreaker with cylindrical hole fastening 0.2 mm corner radius; 4.76 mm plate thickness Faster cycles with consistent chip control The combination of GH110 grade and an optimised double-sided chipbreaker improves process stability during turning operations. The selected carbide formulation balances wear resistance and toughness to resist flank wear and chipping, which leads to longer periods between index changes and fewer unscheduled tool interventions. For shops aiming to increase throughput, the geometry reduces unpredictable chip formation and supports reliable swarf evacuation, resulting in steadier cycle times and less machine downtime. Secure clamping and geometry that supports accuracy A triangular insert with a 60° included angle and a cylindrical hole provides a rigid seat and repeatable location in standard ISO holders. The combination of a 0.2 mm corner radius and 4.76 mm plate thickness gives a robust cutting edge while retaining the ability to produce sharp profiles where needed. This geometry reduces vibration and contributes to consistent surface finish; the through-hole fastening method simplifies mounting and ensures the insert locates precisely for every indexing operation, which supports repeatable part tolerances. Practical adaptability and simplified selection While the insert is intended for turning applications, the indexable insert concept means edge changes are fast and cost-efficient compared with solid-tool regrinding. The GH110 grade complements the geometry by offering a compromise between longevity and edge support, so shops can select this insert when facing mixed production runs where both wear resistance and impact tolerance are required. For best results, choose the chipbreaker style and holder that match the workpiece material and the intended cutting parameters, ensuring the insert’s strengths are fully utilised in the machining strategy. For machining operations that demand reliable edge life and predictable chip behaviour, contact Metav Werkzeuge to discuss the Tungaloy GH110 inserts (SKU TUN6808140) and obtain tailored advice or a quotation. Technical data Article number: 6808140 Manufacturer SKU: TUN6808140 SKU: 6808140-Tungaloy Designation: TNGG160402 GH110 Tungaloy indexable insert Dimensions & geometry Insert size: 16 mm Plate thickness: 4.76 mm Corner radius: 0.2 mm Included angle: 60° Clearance angle: 0° Materials & features Carbide material Grade: GH110 Triangular insert shape Double-sided chipbreaker Cylindrical hole for fastening ISO indexable insert series FAQ What does the designation TNGG160402 GH110 indicate? The designation identifies a triangular indexable insert (TNGG) with ISO size 160402 and carbide grade GH110, specifying geometry, corner radius and the intended grade characteristics for turning tasks. How many cutting edges are available per insert? The triangular, double-sided design provides multiple indexable cutting edges; each side can be indexed to present a fresh edge, delivering several usable cutting edges per insert. Is the insert compatible with standard ISO turning holders? Yes, the insert conforms to ISO indexable insert standards and is intended for use with compatible external holders or boring bars that match form, clearance and clamping requirements. Which features of the insert improve chip control? The built-in double-sided chipbreaker and the GH110 grade work together to shape chips consistently, reducing clogging and improving evacuation during turning operations. Can this insert be used for both external and internal turning? The geometry and hole fastening allow use in both external holders and appropriate boring bars for internal turning, provided the holder secures the insert with matching form and tolerance. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
Fragen zu diesen Produkten??
Mit mehr als 30 Jahren Erfahrung beraten wir Sie gerne persönlich.
Tel.: +49 2822 7131930
Mail: info@metav-werkzeuge.com