CNMM 250924 T9215 Wendeplatten - Tungaloy
Take advantage of the combination of ISO compatibility, CVD-coated carbide grade T9215, and a robust 2.4 mm corner radius for high uptime and consistent part quality; order the CNMM250924 T9215 turning insert directly via Metav Werkzeuge or consult our specialists for machining advice. CNMM 250924 T9215 ISO turning insert — CVD-coated carbide for turning, Tungaloy The CNMM 250924 T9215 is a rhombic ISO turning insert designed for medium-steel machining, offering a CVD-coated carbide substrate and a single-sided chipbreaker for reliable chip control in continuous to slightly interrupted cuts. CVD-coated carbide grade T9215 for wear resistance Rhombic CNMM shape with 80° cutting angle 2.4 mm corner radius for robust edge strength Optimised for medium steel and light interrupted cuts Longer tool life through advanced CVD coating and grade selection The CVD-coated T9215 grade combines a wear-resistant surface layer with a tough carbide substrate to balance abrasion resistance and fracture safety. This configuration is particularly effective in continuous production where long tool life reduces changeover frequency and machine downtime. The coating process creates a thin, uniform layer that protects the substrate against adhesive and abrasive wear; as a result, cutting edge life is extended and the number of regrinds or insert changes is reduced, improving overall machining economy. Predictable geometry for steady process results Manufactured to ISO dimensions in a rhombic CNMM form, the insert features an 80° cutting angle and a 0° relief angle that fit standard external and internal turning holders. The 2.4 mm corner radius provides a compromise between edge strength and finish capability, while the 9.52 mm thickness boosts stability under load. Compatibility to a given holder is defined by form, relief angle, tolerance class, fastening method, size and thickness, so the insert integrates into existing tool systems with repeatable clamping and concentricity when matched correctly. Better chip control and process security for productive turning The single-sided chipbreaker is optimised for medium-steel applications and supports consistent chip formation in both continuous and lightly interrupted cuts. Stable chip flow reduces the risk of built-up edge and vibration, which in turn improves surface finish and reduces scrap. The carbide substrate ensures breakage resistance under typical turning forces, enabling higher cutting parameters and consequently improved productivity without compromising part integrity. Seamless system integration and straightforward handling The insert is supplied in the ISO CNMM format with a cylindrical locating hole for positive seating in compatible holders; a matching shim or clamping set and replacement screws form the complete system. As an ISO-standardised component, the insert simplifies stock management and replacement planning across multi-shift operations. Labelling and manufacturer SKU make reordering predictable and ensure identical performance across batches, supporting process stability and ease of procurement. For professional machining with Tungaloy's CVD-coated T9215 grade, contact Metav Werkzeuge to request technical specification sheets or to place an order; eMail info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: 6774093 Manufacturer SKU: TUN6774093 Brand: Tungaloy Model series: ISO turning inserts Designation: CNMM250924 T9215 Measurements & geometry Size: 25 Thickness: 9.52 mm Corner radius: 2.4 mm Cutting angle: 80° Relief angle: 0° Hole: cylindrical Materials & features Material: carbide Coating: CVD-coated (T9215) Chipbreaker: single-sided Shape: rhombic (CNMM) Application: turning Suitable for: medium steel, continuous to light interrupted cuts Compatibility: ISO holder by form, relief, tolerance, fastening, size, thickness FAQ What materials is this insert designed for? The CNMM250924 T9215 insert is formulated for medium steel machining; its CVD-coated T9215 grade balances wear resistance and fracture safety for continuous to light interrupted cuts. Which holder characteristics determine compatibility? Compatibility is determined by insert form, relief angle, tolerance class, fastening type, size and thickness; the CNMM format and cylindrical hole require a matching ISO CNMM holder and clamping set. How does the chipbreaker affect performance? The single-sided chipbreaker stabilises chip formation and evacuation in medium-steel turning, improving surface finish and reducing the likelihood of built-up edge or vibration-related defects. Is this insert suitable for interrupted cuts? Yes — the carbide substrate and T9215 coating provide breakage resistance suitable for continuous machining and light interrupted cuts; heavy interruptions may require a different geometry or grade. Which dimensions should be considered when reordering? Key dimensions for reordering are the ISO designation (CNMM250924), corner radius 2.4 mm, thickness 9.52 mm, and the manufacturer article number 6774093 to ensure identical replacement parts. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
CNMM 250924 T9215 Wendeplatten - Tungaloy
Take advantage of the CVD-coated carbide grade and robust 80° rhombic geometry for reliable medium-steel turning; the combination of wear resistance and fracture toughness supports high productivity in continuous to light interrupted cuts. Order directly via Metav Werkzeuge or consult the team for matching holder and clamping recommendations. CNMM 250924 T9215 indexable turning insert for turning – Tungaloy A CNMM250924 indexable insert in a rhombic form designed for general turning applications, offering an 80° included angle and optimised grade for medium-steel machining. ISO rhombic insert CNMM250924, 80° geometry CVD-coated carbide grade T9215 for medium steel 2.4 mm corner radius for robust edge life Cylindrical hole, 9.52 mm thickness for secure clamping Consistent performance for medium-steel machining The combination of CVD-coated carbide and the T9215 grade delivers a balance between wear resistance and edge toughness that suits medium-steel applications. The insert’s material and coating are selected to extend tool life under continuous and lightly interrupted cutting conditions, improving process stability and reducing unplanned tool changes. This results in a more predictable machining rhythm and supports higher throughput in production environments. Geometry and clamping that support reliable production The 80° geometry and rhombic shape provide a versatile cutting profile for both external and internal turning. A 2.4 mm corner radius gives a durable cutting edge that resists chipping under moderate feed and depth of cut, while the cylindrical hole and 9.52 mm plate thickness ensure secure clamping in compatible holders. Compatibility depends on holder form, clearance angle, tolerance class, fastening method, size and thickness, so pairing with the correct outer holder or boring bar is essential for repeatable results. What the coating and substrate mean in practice A CVD coating on a carbide substrate creates a hard, wear‑resistant surface that reduces flank wear and maintains cutting-edge geometry for longer. The carbide body provides the necessary substrate toughness; combined with the coating, it allows sustained cutting performance and consistent surface finish on steel. For production planning, this means fewer insert changes and a lower rate of edge-related scrap when operating within recommended cutting parameters. Application guidance and process benefits Designed for turning operations, the insert is suitable for external and internal turning where a single-sided chipbreaker matches the workpiece material and machining stability. Selecting the correct chipbreaker and grade for the job helps to manage chip formation and evacuation, improving surface integrity and reducing cycle times. The overall design supports more efficient material removal, contributing to a higher productivity rate and a more economical process per part produced. For dependable productivity in turning applications, choose the Tungaloy CNMM250924 T9215 insert and contact Metav Werkzeuge for tailored holder matching and rapid availability Technical Data Article number: 6773850 SKU: 6773850-Tungaloy Manufacturer SKU: TUN6773850 Model series: ISO turning indexable inserts Facts Thickness: 9.52 mm Inscribed circle / size: 25 mm Included angle: 80° Corner radius: 2.4 mm Clearance angle: 0° Special features Shape: rhombic Hole: cylindrical Coating: CVD-coated Material: carbide Grade: T9215 Chipbreaker: single-sided Application: turning Compatibility: ISO standard insert, matched by holder form and dimensions FAQ Which holders are compatible with this insert? Compatibility is determined by the holder’s form, clearance angle, tolerance class, fastening method, size and plate thickness; the CNMM250924 insert requires an ISO-compatible rhombic external holder or boring bar designed for inserts with a cylindrical hole. Is this grade suitable for interrupted cuts? The T9215 grade is optimised for continuous to light interrupted cuts; it balances wear resistance and toughness to perform well under modest interruption without excessive edge chipping. What materials is this insert intended for? This insert is primarily intended for medium-steel machining; the CVD coating and carbide substrate provide the wear resistance and toughness required for this material group. How does the 2.4 mm corner radius affect cutting? A 2.4 mm corner radius enhances edge robustness, improves tool life under higher feed or depth of cut and can help produce a consistent surface finish when feeds and speeds are set accordingly. Can this insert achieve high productivity? Yes, the combination of CVD-coated carbide and the T9215 grade supports higher cutting volumes with stable performance, making the insert suitable for productive turning operations. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
CNMM 250924 T9225 Wendeplatten - Tungaloy
Take advantage of the robust CVD‑coated carbide (T9225) and the 2.4 mm nose radius for consistent, long‑running performance in medium to heavy steel turning; the ISO sizing and cylindrical hole ensure secure mounting and simple integration into existing tooling stacks. Order directly via Metav Werkzeuge or consult our technical advisers for selection support. CNMM 250924 T9225 — CNMM250924 turning insert (rhombic, 80°) by Tungaloy The CNMM250924 T9225 is an ISO‑standard, rhombic turning insert intended for external and internal turning; engineered for medium to heavy steel machining where toughness and reliable chip control are required CVD-coated carbide grade T9225 80° rhombic shape with 2.4 mm radius Cylindrical hole for secure fixation Suitable for medium to heavy steel turning Reliable cutting performance for changing cutting conditions The CVD‑coated carbide substrate in this grade delivers a balance of toughness and wear resistance, making it suitable for interrupted cuts and variable engagement depths. The insert’s geometry provides stable cutting forces, which helps to reduce chatter and maintain dimensional stability on the workpiece. As a result, production runs benefit from consistent tool life and fewer unscheduled changeovers, supporting higher machining uptime and predictable planning. Secure mounting and ISO compatibility for production lines Designed to the ISO specification, the rhombic plate and the cylindrical hole enable reliable fixation in compatible holders and boring bars. The combination of form, clearance angle and tolerance class determines compatible carriers; the insert’s 80° included angle and 0° clearance suit standard external turning applications while the 9.52 mm thickness contributes to stiffness when clamped. This makes the insert straightforward to integrate into existing tool systems without additional adapters, supporting rapid tool exchanges and minimal setup time. Practical advantages for workshop efficiency The one‑sided chipbreaker and the 2.4 mm nose radius support controlled chip formation and improved surface finishes in typical steel operations. The robust universal grade is intended to handle a broad range of steel alloys under medium to heavy cut conditions, reducing the need for multiple specialised grades. For production environments that value repeatability and easy tool management, the insert’s ISO form and clear geometry reduce machining variability and simplify inventory handling. Technical advisers at Metav Werkzeuge can assist with chipbreaker selection and holder pairing to match process stability and workpiece requirements. Contact Metav Werkzeuge for application guidance and original Tungaloy supplies — eMail: info@metav-werkzeuge.com or phone +49 2822 7131930; specialists are available to advise on grade selection and holder compatibility Technical data Article number: 6781331 SKU: 6781331-Tungaloy Manufacturer SKU: TUN6781331 Name: CNMM250924 T9225 Tungaloy-Wendeplatte Model series: ISO-Drehwendeschneidplatten Material: Hartmetall Facts Nose radius: 2.4 mm Included angle: 80° Clearance angle: 0° Thickness: 9.52 mm Size: 25 Hole: with cylindrical hole Special features CVD-coated carbide (T9225) Rhombic plate shape One-sided chipbreaker ISO designation: CNMM250924 Application: Turning Typical system: external/ internal turning with compatible holder FAQ What materials is this insert designed to machine? The CNMM250924 T9225 insert is formulated for medium to heavy steel machining and performs reliably where increased toughness is required. How is the insert secured in the holder? Fixation is provided via the cylindrical hole in the insert; compatibility depends on holder form, tolerance class and clamping method. Which properties does the T9225 grade offer compared with other grades? T9225 is a CVD‑coated carbide grade that offers a balance of wear resistance and toughness, intended for productive machining under variable engagement. Can this insert be used for internal turning as well as external turning? Yes, the ISO rhombic form and geometry permit both external and internal turning when paired with suitable holders or boring bars. What chip control can be expected from the one-sided chipbreaker? The one‑sided chipbreaker is designed to produce controlled chips and support surface finish in typical steel turning operations. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
CNMM 250924 T9225 Wendeplatten - Tungaloy
The combination of CVD-coated carbide and the T9225 universal grade delivers reliable toughness for medium to heavy steel turning, while the CNMM250924 geometry and 2.4 mm corner radius ensure stable cutting edges under variable engagement. Order the CNMM250924 directly via Metav Werkzeuge or consult Metav Werkzeuge's specialists for compatibility checks and availability. CNMM250924 T9225 CNMM Turning Insert by Tungaloy — CVD-coated carbide, 2.4 mm radius CNMM250924 is a rhombic ISO indexable insert designed for medium to heavy steel turning, offering robust performance in interrupted and variable-cut conditions. ISO rhombic insert CNMM250924 by Tungaloy CVD-coated carbide grade T9225 for steel 2.4 mm corner radius for reinforced edge Single-sided chipbreaker with cylindrical hole Stable performance under changing cutting conditions The CVD-coated carbide substrate combined with the T9225 grade is engineered for consistent toughness and wear resistance during medium to heavy steel turning. The coating supports thermal stability at elevated cutting speeds, while the grade emphasises reliable chip control and edge integrity when cuts are slightly interrupted or engagement varies. As a result, the indexable insert offers repeatable tool life and predictable performance, which reduces tool-change frequency and supports steady production throughput. Secure clamping and system compatibility for reduced downtime Compatibility with toolholders depends on form, relief angle, tolerance class, fastening, size and thickness; the insert's rhombic geometry and cylindrical hole accommodate standard clamping systems. The 9.52 mm plate thickness and standard ISO dimensions facilitate straightforward mounting in suitable CNMM holders or on boring bars, with the requirement to match the holder pocket and fastening screw. This simplified integration helps to minimise setup time and lowers the risk of incorrect fitting that can cause premature wear or component rejection. Edge strength and chip control for productive turning A 2.4 mm corner radius provides a reinforced cutting edge that balances strength and surface finish for steel machining. The single-sided chipbreaker is optimised for reliable chip formation in a range of cutting depths and feed rates, reducing the likelihood of long, entangling chips and supporting safer, uninterrupted operation. When combined with appropriate cutting data for the workpiece and machine rigidity, the insert contributes to consistent surface quality and process security. Practical assembly and application notes for workshop use The insert is part of an ISO-compliant system comprising the indexable insert, a matching external holder or boring bar, a shim/clamp set and replacement screws. The 80° cutting geometry and 0° relief angle are typical for CNMM-style rhombic inserts and should be matched to the intended turning strategy. For best results in medium to heavy steel work, select cutting parameters in line with the toolholder rigidity and the T9225 grade's balance of toughness and wear resistance to extend tool life and maintain machining stability. Contact Metav Werkzeuge today for application-specific recommendations on the Tungaloy CNMM250924 T9225 turning insert and arrange prompt supply through Metav Werkzeuge. Technical data Article number: 6780934 Manufacturer SKU: TUN6780934 Model series: ISO-Drehwendeschneidplatten Material: carbide Designation: CNMM250924 Grade / coating: T9225, CVD-coated Shape: rhombic Hole: with hole (cylindrical hole) Facts Corner radius: 2.4 mm Thickness: 9.52 mm Inscribed circle / size: 25 mm Cutting angle: 80° Relief angle: 0° Special features Single-sided chipbreaker Intended application: turning Compatible with ISO CNMM holders and boring bars Robust universal grade for medium to heavy steel machining System components: insert, external holder/boring bar, shim/clamp set, replacement screws FAQ What materials is this insert suited for? The CNMM250924 T9225 indexable insert is designed primarily for steel; the T9225 grade provides toughness and wear resistance for medium to heavy steel turning. Does the insert fit standard CNMM holders? Yes. The CNMM250924 geometry and the cylindrical hole conform to ISO CNMM dimensions and are compatible with appropriately matched holders and boring bars when form, relief angle and thickness are observed. What benefits does the CVD coating provide? The CVD-coated carbide offers enhanced thermal stability and wear resistance, helping the insert maintain edge life at higher temperatures common in medium to heavy turning operations. How does the 2.4 mm corner radius affect machining? A 2.4 mm corner radius increases edge strength and reduces chipping risk under variable engagement, supporting stable cutting in heavier or interrupted cuts while contributing to surface integrity. What are the key system components required for installation? Proper installation requires a matching external holder or boring bar, a shim/clamp set and the correct replacement screws specified for CNMM-style inserts; ensuring correct assembly supports reliable machining. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
CNMM 250924 T9225 Wendeplatten - Tungaloy
Take advantage of a robust CVD-coated T9225 grade and a substantial 2.4 mm corner radius to maintain stable chip formation and tool life under variable engagement; the 80° rhombic geometry and 9.52 mm thickness ensure secure clamping and consistent performance in medium to heavy steel turning. Order the insert directly via Metav Werkzeuge or consult our specialists for selection and application support. CNMM 250924 T9225 indexable turning insert, rhombic 80° (Tungaloy) A CNMM250924 indexable insert intended for external and internal turning, offering a durable CVD-coated carbide grade for mixed and interrupted cutting conditions. CVD-coated T9225 carbide grade for steels Rhombic 80° geometry for stable clamping 2.4 mm corner radius for robust edge strength 9.52 mm plate thickness for secure fixation Improved productivity through material-adapted cutting performance The combination of a CVD-coated carbide coating and the T9225 grade provides a balance between toughness and wear resistance, designed for medium to heavy steel machining where chip control and edge stability matter. With its one-sided chipbreaker, the insert promotes predictable chip flow even under slightly interrupted cuts, reducing the risk of tool damage and workpiece rework. The measurable values — 2.4 mm corner radius, 9.52 mm thickness and 80° rhombic form — translate directly into fewer tool changes and steadier cycle times on lathes and turning centres. Seamless integration into established tool systems As an ISO-standard insert, compatibility depends on geometry, clearance angle, tolerance class, fastening and size; this reduces selection ambiguity and simplifies tool inventory management. The insert is designed to work with a matching external holder or boring bar, together with a shim/clamping set and replacement screws, allowing straightforward retrofitting into existing toolholders. Clear mechanical criteria eliminate guesswork when pairing the insert with holders, helping to shorten setup time and lower the risk of mounting errors. Reliable results backed by application versatility and support Engineered for both external and internal turning tasks, the insert is particularly suitable where changing engagement or intermittent cuts demand increased toughness. The CNMM250924 T9225 design supports stable chip formation and consistent surface finish, contributing to predictable process outcomes and less scrap. If additional machining parameters or compatibility checks are required, technical advice is available to ensure the cutting solution matches the workpiece material and machine dynamics. Contact Metav Werkzeuge today to discuss the Tungaloy T9225 solution for demanding steel turning tasks — phone +49 2822 7131930 or eMail info@metav-werkzeuge.com for application guidance and fast delivery Technical Data Article number: 6780695 Facts Insert size: 25 mm Thickness: 9.52 mm Corner radius: 2.4 mm Clearance angle: 0° Cutting angle: 80° Special features Material: carbide Coating: T9225 (CVD) Plate form: rhombic Hole: cylindrical Chipbreaker: one-sided Application: external and internal turning FAQ What materials is this insert suited for? The Tungaloy CNMM250924 with T9225 coating is tailored for steel machining, especially medium to heavy steel and applications with slightly interrupted cuts. How does the 2.4 mm corner radius affect performance? A 2.4 mm corner radius increases edge strength and resistance to chipping, improving tool life during heavy engagement and contributing to more consistent surface quality. Is the insert compatible with standard holders? Yes — the insert follows the ISO designation and requires matching of form, clearance angle, tolerance class, fastening, size and thickness to ensure proper holder compatibility. What advantages does the T9225 CVD coating provide? The T9225 CVD coating offers a compromise of toughness and wear resistance, promoting stable chip control and longer service life in variable cutting conditions. Can the insert handle interrupted cuts? The insert’s one-sided chipbreaker and robust grade make it suitable for slightly interrupted cutting conditions typical in many turning operations. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
CNMM 250924 T9235 Wendeplatten - Tungaloy
Take advantage of a tough CVD-coated carbide grade designed for steel turning, combined with a robust 2.4 mm corner radius and 80° rhombic geometry for improved edge strength and chip control; order the CNMM250924 T9235 insert directly via Metav Werkzeuge or ask our consultants if needed. CNMM250924 T9235 ISO rhombic indexable turning insert — Tungaloy CNMM250924 T9235 is an ISO-form indexable insert for external and internal turning, engineered for steel machining where interrupted cuts or unstable conditions require a tough, reliable grade. CVD-coated carbide grade T9235 ISO rhombic CNMM250924 80° geometry 2.4 mm corner radius for robust engagement Single-sided chipbreaker, cylindrical hole Consistent cutting in unstable turning conditions The CNMM250924 insert combines a CVD-coated surface with a cemented carbide substrate to deliver toughness where chip formation is unpredictable. The T9235 grade is formulated for steel at moderated cutting speeds and excels when the cut is intermittent or the setup lacks rigidity. Choosing a tougher grade reduces edge chipping and unplanned stoppages, which in turn improves throughput and lowers rework rates. The result is a more predictable machining process and fewer scrap parts. Strong edge and secure clamping for repeatable results With an 80° rhombic geometry and a 2.4 mm corner radius, the insert provides an enlarged edge zone that tolerates heavier engagement and sudden load changes. The insert’s 9.52 mm thickness increases support in the pocket and, together with the cylindrical hole, ensures secure clamping in standard ISO holders. These features contribute to repeatable dimensional accuracy and a longer effective tool life, reducing downtime for insert changes and adjustment. Improved chip control and application range The single-sided chipbreaker is tuned to the grade and typical steel applications, promoting reliable chip segmentation under varying feeds and depths of cut. This aids evacuation in both external and internal turning operations and reduces the risk of chip entanglement. The combination of grade, chip control geometry and substrate makes this insert suitable for unstable setups, repair work and batch production where robustness matters more than maximum cutting speed. System compatibility and practical guidance The insert is part of an ISO series and is compatible with holders that match its shape, clearance angle, tolerance class, fastening method, size and thickness. When integrating the insert into a tool system, select a holder and clamping kit rated for rhombic CNMM geometry and verify pocket support to exploit the insert’s stiffness. For applications requiring different cutting regimes, alternative grades or chipbreaker variants can be considered to balance surface finish and productivity. For robust steel turning, request the Tungaloy CNMM250924 T9235 insert from Metav Werkzeuge—our specialists can advise on holder compatibility and optimal cutting data; contact Metav Werkzeuge at info@metav-werkzeuge.com or +49 2822 7131930 for tailored support. Technical Data Article number: 6785925 Manufacturer SKU: TUN6785925 Our SKU: 6785925-Tungaloy Key dimensions Shape / designation: CNMM250924 Size: 25 Thickness: 9.52 mm Corner radius: 2.4 mm Relief angle: 0° Included angle: 80° Materials & Features Grade: T9235 Coating: CVD Substrate: cemented carbide Chipbreaker: single-sided Hole style: cylindrical hole Shape: rhombic Model series: ISO turning indexable inserts Application: turning FAQ What materials is this insert intended for? The CNMM250924 T9235 insert is intended primarily for steel machining; the T9235 grade is optimised for tougher conditions and interrupted cuts in steel. How does the chipbreaker affect machining performance? The single-sided chipbreaker on this insert improves chip segmentation and evacuation during turning operations, helping maintain stable cutting when the setup vibrates or cuts are interrupted. Is the insert compatible with standard ISO CNMM holders? Yes, the insert follows the ISO CNMM form; compatibility depends on matching the holder to the insert’s shape, relief angle, tolerance and thickness. What benefit does the 2.4 mm corner radius provide? A 2.4 mm corner radius increases edge strength and allows more robust engagement, reducing the likelihood of brittle edge failure during heavy or interrupted cuts. Which features support secure clamping and repeatability? The combination of 9.52 mm thickness, the cylindrical central hole and ISO rhombic geometry provides enhanced pocket support and secure clamping for repeatable positional stability. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
CNMM 250924 T9235 Wendeplatten - Tungaloy
Benefit from the combination of CVD-coated carbide toughness and an 80° rhombic geometry with a 2.4 mm corner radius for robust turning performance in unstable or interrupted cuts; order the CNMM250924 directly via Metav Werkzeuge or ask our consultants for tailored application advice. CNMM250924 T9235 — Tungaloy indexable turning insert, CVD-coated carbide, 80° rhombic A CNMM250924 T9235 indexable insert designed for ISO-series external and internal turning, optimised for interrupted cuts and unstable machining conditions CVD-coated carbide grade T9235 80° rhombic geometry for versatile turning 2.4 mm corner radius for robust cutting edge Single-sided chipbreaker for interrupted cuts Increased process reliability where stability is limited The CVD-coated carbide composition and the T9235 grade provide a tough substrate tailored for machining steel under lower cutting speeds and unstable conditions. The insert’s construction reduces the risk of chipping during interruptions in the cut and supports longer effective edge life, which translates into fewer tool changes and improved uptime. As an ISO-series component, compatibility with a holder depends on form, clearance, tolerance class, fastening, size and thickness, so the insert can be integrated into standard tool systems when those parameters match. Stable edge geometry for predictable surface finish With an 80° rhombic profile and a 2.4 mm corner radius, the geometry delivers a balance between edge strength and cutting performance. The 0° clearance and the centrally located cylindrical mounting hole ensure secure positioning in compatible holders or boring bars, while the single-sided chipbreaker supports controlled chip formation during interrupted and semi-stable cuts. These features help maintain a consistent surface quality and reduce the likelihood of sudden tool failure, making the solution particularly useful for small-batch production and repair work where repeatability matters. Practical integration into turning toolsets and cost-effective machining Intended for external and internal turning, the insert forms part of a practical system consisting of the ISO insert, a matching external holder or boring bar, a shim/clamping set and replacement screws. Selecting the correct chipbreaker and grade for the workpiece material and machining stability is essential: the T9235 grade suits tougher scenarios in steel machining, promoting productive machining and minimising unplanned downtime. Workshops and job shops benefit from predictable performance, straightforward replacement, and compatibility with common ISO tooling systems, supporting efficient process planning and inventory management. For reliable turning under unstable conditions, request technical advice or the Tungaloy CNMM250924 T9235 indexable insert from Metav Werkzeuge via info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Manufacturer article number: 6786064 SKU: 6786064-Tungaloy Manufacturer SKU: TUN6786064 Label: CNMM250924 T9235 Tungaloy-insert Model series: ISO-turning indexable inserts Material: carbide Story trigger: indexable inserts Core specifications Insert designation: CNMM250924 Geometry: rhombic, 80° Corner radius: 2.4 mm Thickness: 9.52 mm Size: 25 mm Clearance angle: 0° Hole: with cylindrical hole Chipbreaker: single-sided Materials & features Coating: CVD Grade: T9235 (tough steel grade) Application: turning (external and internal) Typical use: interrupted cuts, unstable conditions System compatibility: ISO-series; fit determined by form, clearance, tolerance class, fastening, size and thickness System components: insert, external holder or boring bar, shim/clamping set, replacement screws FAQ What materials is this insert suited for? The CNMM250924 T9235 Tungaloy indexable insert (SKU 6786064-Tungaloy) is formulated for machining steel, especially where a tough grade is required for interrupted cuts or unstable conditions. How does the T9235 grade affect tool life? Tungaloy’s T9235 grade combines a CVD-coated carbide substrate with a formulation aimed at toughness; the result is improved resistance to edge breakage and more consistent life in lower-speed, unstable turning applications with the CNMM250924 insert. Which geometry and mounting features ensure secure clamping? The insert’s 80° rhombic geometry, 0° clearance and cylindrical mounting hole provide a secure fit in compatible holders; proper matching of form, tolerance class and fastening is required for safe operation with the CNMM250924. Can this insert be used for both external and internal turning? Yes — the ISO-series design supports both external and internal turning when combined with suitable holders or boring bars; select the correct chipbreaker and clamping components for the intended setup. What type of chip control does this insert provide? The CNMM250924 features a single-sided chipbreaker designed to manage chips in interrupted cutting conditions and to encourage predictable chip flow in varying stability scenarios. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
CNMM 250924 T9235 Wendeplatten - Tungaloy
High process security and predictable tool life are ensured by the combination of a CVD-coated cemented carbide grade and a substantial 9.52 mm plate thickness, making the insert suitable for challenging steel turning tasks; order the CNMM250924 directly via Metav Werkzeuge or request advice from the consultants if required. CNMM250924 T9235 turning insert by Tungaloy — CVD-coated cemented carbide, 0° clearance CNMM250924 is an ISO‑standard indexable turning insert designed for external and internal turning in steel applications, offering a robust geometry for interrupted cuts and unstable conditions. ISO-compliant geometry for reliable clamping CVD-coated carbide grade T9235 for steel 0° clearance for robust interrupted cuts 2.4 mm corner radius for stable cutting action Consistent performance for steel turning with a tough grade The CNMM250924 insert features a CVD-coated cemented carbide substrate and the T9235 grade, a formulation developed for toughness rather than maximum speed. This makes the insert especially suitable where irregular chip load, interrupted cuts or machine instability occur. The combination of coating and grade improves edge resilience and reduces the likelihood of chipping, which translates into fewer unscheduled tool changes and more consistent cycle times on production lines. Designed geometry for clamping and system compatibility As an ISO‑standard indexable insert, compatibility with the host toolholder is determined by shape, clearance angle, tolerance class, fastening method, size and thickness. The rhombic plate form and central cylindrical hole allow secure fixing with standard clamp or screw systems. The relatively thick body improves rigidity in the tool system, so paired with a suitable external holder or boring bar the insert contributes to reduced vibration and better surface integrity on turned components. Practical advantages under unstable conditions and interrupted cuts The 0° clearance and the one‑sided chipbreaker design are optimised for stable chip formation when conditions are less than ideal. The 2.4 mm corner radius increases edge strength and distributes cutting forces over a larger area, which reduces flank wear and prolongs edge life during heavy engagement. Selecting this insert means prioritising reliability: it is intended for moderate cutting speeds in steel where tool robustness and repeatable results are more important than maximum metal removal rate. Handling, system components and application guidance The insert forms part of a system consisting of the ISO indexable plate, a matching external holder or boring bar, a shim/clamping set and spare screws. Plate thickness of 9.52 mm contributes to mechanical stability; the 25 size and 80° included angle suit a broad range of turning operations. For efficient integration, choose a holder with matching tolerance class and fastening arrangement. The one‑sided chipbreaker aids chip evacuation on common turning tasks, simplifying process setup and reducing the need for frequent adjustments. For robust and reliable steel turning, specify the Tungaloy CNMM250924 T9235 insert through Metav Werkzeuge or contact the consultants at Metav Werkzeuge for tailored recommendations: info@metav-werkzeuge.com | +49 2822 7131930 Technical Data Article number: 6786033 Manufacturer SKU: TUN6786033 SKU: 6786033-Tungaloy Designation: CNMM250924 T9235 Tungaloy indexable insert Facts Insert size: 25 Plate thickness: 9.52 mm Corner radius: 2.4 mm Included angle: 80° Clearance angle: 0° Hole: with hole (cylindrical) Plate shape: rhombic Special features Material: CVD-coated cemented carbide Grade: T9235 (tough grade for steel) Chipbreaker: one-sided Typical application: external and internal turning System: ISO indexable insert with matching holder, shim and clamping set FAQ What materials is this insert intended for? The CNMM250924 T9235 insert is formulated primarily for steel machining; the CVD-coated cemented carbide and T9235 grade favour toughness in interrupted or unstable cutting conditions. Which toolholders are compatible with this insert? Compatibility is determined by the insert geometry and ISO standard: the rhombic shape with cylindrical hole fits ISO‑compliant external holders and boring bars that accept a 25-size CNMM plate and secure it with the appropriate clamp or screw. How does the 2.4 mm corner radius affect cutting performance? A 2.4 mm corner radius increases edge strength and spreads cutting loads, resulting in improved tool life and more stable surface finishes when machining under heavy engagement or variable chip loads. Is the insert suitable for interrupted cuts and unstable operations? Yes. The T9235 grade and the insert’s robust 9.52 mm thickness, combined with the one‑sided chipbreaker and 0° clearance, make it well suited for interrupted cuts and cases where machine or workpiece stability is limited. What system components are required to assemble the insert for use? A complete system typically comprises the ISO indexable plate, a compatible external holder or boring bar, a shim/clamping set and the correct fastening screws; Metav Werkzeuge can advise on the matching holder and spare parts. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
CNMM 250932 T9215 Wendeplatten - Tungaloy
Take advantage of the combination of CVD-coated carbide T9215, a 3.2 mm corner radius and ISO conformity for consistent, high-productivity steel turning; order directly via Metav Werkzeuge or ask the consultants for application guidance. CNMM 250932 T9215 indexable insert for turning — Tungaloy CNMM250932-TUS is an ISO-standard rhombic indexable insert intended for external and internal turning, engineered for productive machining of medium steel. CVD-coated carbide grade T9215 Optimised for medium steel turning 3.2 mm corner radius for robust profiling ISO rhombic shape with 80° included angle High productivity through wear-resistant grade and proven coating The insert uses a CVD-coated carbide substrate in grade T9215, which combines elevated wear resistance with good fracture tolerance. This composition makes the tool a reliable choice for continuous to slightly interrupted cuts in medium steel, enabling longer edge life and fewer tool changes. The coating process forms a protective hard layer that reduces flank wear; for production environments this translates directly into steadier cycle times and more predictable tool consumption. Secure mounting and ISO compatibility for straightforward tool assembly Designed as an ISO-standard turning insert, compatibility with holders is achieved through matching form, relief angle, tolerance class, fastening method, size and thickness. The insert features a cylindrical hole for positive locating and safe clamping in suitable chucks or boring bars. The specified 9.52 mm thickness and 25 mm size are standard dimensions that simplify tool planning and replacement in established tool systems, reducing downtime during insert exchanges. Geometry and chip control that support consistent surface quality The rhombic shape with an 80° included angle and a 3.2 mm corner radius provides a robust cutting edge for profiling and shoulder work, improving resistance to mechanical shock. The integrated TUS chipbreaker is matched to the grade and typical steel applications to support controlled chip flow and surface finish. Selecting this insert helps maintain repeatable machining results with a focus on stable cutting conditions rather than overly aggressive feeds, which is especially valuable for jobs where consistent quality is required. For high-productivity medium steel turning with Tungaloy’s T9215 grade, contact Metav Werkzeuge for availability and expert advice at info@metav-werkzeuge.com or +49 2822 7131930 Technical data Article number: 6773851 Manufacturer SKU: TUN6773851 SKU: 6773851-Tungaloy ISO designation: CNMM250932-TUS Grade: T9215 Chipbreaker: TUS Material: carbide Coating: CVD Facts Corner radius: 3.2 mm Thickness: 9.52 mm Inscribed circle / size: 25 mm Included angle: 80° Relief angle: 0° Special features Rhombic plate form for external and internal turning Cylindrical hole for secure clamping Suitable for continuous to slightly interrupted cuts Compatibility determined by form, relief angle, tolerance class, fastening, size and thickness System components: ISO turning insert, matching external holder or boring bar, shim/clamp set and replacement screws FAQ What materials is this insert best suited for? The CNMM250932-TUS insert in Tungaloy’s T9215 grade is optimised for medium steel and offers a balance of wear resistance and fracture toughness for productive machining. Is the insert compatible with standard ISO holders? Yes—being an ISO-standard rhombic insert, compatibility depends on matching form, relief angle, tolerance class, fastening, size and thickness; the CNMM250932-TUS is designed for such systems. What role does the TUS chipbreaker play? The TUS chipbreaker promotes predictable chip formation and evacuation, supporting surface quality and reducing the risk of chip-related interruptions during turning operations. Can this insert be used for interrupted cuts? The T9215 grade and the insert geometry are suitable for continuous to slightly interrupted cuts; heavier interruptions may require a different grade or insert geometry. How is the insert secured in the holder? The insert has a cylindrical hole for positive locating and is fixed using the appropriate clamping/shim set and screws as per the ISO holder system. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
CNMM 250932 T9225 Wendeplatten - Tungaloy
Take advantage of the combination of CVD-coated carbide performance, an 80° rhombic form and a 3.2 mm corner radius for stable medium-to-heavy turning operations; order directly via Metav Werkzeuge or consult our specialists for holder compatibility and recommended cutting data. CNMM250932-TUS T9225 CNMM 250932 Turning Insert by Tungaloy — CVD-coated carbide, 3.2 mm radius, 80° A CNMM250932-TUS T9225 ISO turning insert designed for external and internal turning where a robust universal grade is required for variable engagement conditions and lightly interrupted cuts. CVD-coated carbide grade T9225 80° rhombic insert form 3.2 mm corner radius For medium to heavy steel turning Consistent cutting performance for demanding steel turning The insert delivers reliable, repeatable results through its CVD-coated carbide specification and the T9225 grade. This combination provides a good balance of toughness and wear resistance, which is particularly beneficial for medium to heavy machining of steel where cuts can be slightly interrupted. The 80° rhombic geometry ensures stable cutting directions and predictable tool engagement, while the 3.2 mm corner radius helps to extend edge life and maintain dimensional accuracy during longer tool paths. The description of the grade as a robust universal sort indicates suitability across a broad range of steel alloys under varying stability conditions. Secure clamping and ISO compatibility that reduce setup time Compatibility with the toolholder depends on form, clearance angle, tolerance class, fixing method, size and thickness; the insert is manufactured to ISO standards to simplify selection. The ISO designation 250932 and the rhombic form allow easy matching to common external holders and boring bars, and the presence of a central cylindrical hole supports secure mounting with standard screws or clamp sets. Secure clamping reduces vibration and contributes to a consistent surface finish and longer tool life, turning the insert’s geometric and tolerance conformity into direct production benefits. Practical advantages and application range in production Equipped with the TUS chipbreaker, this indexable insert manages chip formation for improved evacuation during turning, reducing the risk of recutting and heat concentration at the edge. The carbide substrate, combined with the CVD coating, supports effective heat resistance and abrasion control, which in turn lowers tooling costs per component through longer service intervals. Intended primarily for external and internal turning of steel, the insert is a practical choice for job shops and production cells requiring a versatile, reliable solution for medium to heavy machining tasks. For application advice or availability of the CNMM250932-TUS insert, contact Metav Werkzeuge at info@metav-werkzeuge.com or call +49 2822 7131930 — our specialists will advise on the optimal holder configuration and cutting data for the intended operation Technical data Article number: 6781286 Manufacturer SKU: TUN6781286 SKU: 6781286-Tungaloy Model series: ISO turning inserts Name: CNMM250932-TUS Facts ISO code: 250932 Corner radius: 3.2 mm Plate size: 25 mm Thickness: 9.52 mm Clearance angle: 0° Angle: 80° Special features Material: CVD-coated carbide (grade T9225) Chipbreaker: TUS Hole: with hole, cylindrical hole Application: external and internal turning Suitable for: medium to heavy steel turning Brand: Tungaloy FAQ What materials is this insert suited for? The CNMM250932-TUS T9225 insert is specified for medium to heavy steel turning; the T9225 grade and CVD coating provide the required toughness and wear resistance for a wide range of steel alloys. How does the chipbreaker influence machining? The TUS chipbreaker on this indexable insert controls chip shape and evacuation, which reduces recutting and thermal load at the edge, improving surface finish and tool life during continuous or slightly interrupted cuts. Is the insert compatible with standard ISO holders? Yes — manufactured to ISO turning insert standards (ISO code 250932), the geometry, hole style and thickness permit fitting in compatible external holders and boring bars when the holder matches form, clearance angle and size. What advantages does the 3.2 mm corner radius provide? A 3.2 mm corner radius increases edge strength and distributes cutting forces, offering longer edge life and improved dimensional stability in medium-to-heavy turning operations. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
CNMN 120408 FX105 Wendeplatten - Tungaloy
Achieve reliable turning performance with the combination of Tungaloy's FX105 grade and ISO CNMN geometry; the insert’s 0.8 mm corner radius and rhombic 80° profile deliver stable edge life and predictable chip formation—order via Metav Werkzeuge or contact our advisers for configuration support. CNMN 120408 FX105 ISO indexable turning insert — carbide, 0.8 mm corner radius | Tungaloy A CNMN120408 FX105 indexable insert engineered for external and internal turning with ISO‑compliant geometry and compatibility across standard holders. ISO‑compliant CNMN geometry FX105 Tungaloy carbide grade 0.8 mm corner radius for robust edges Suitable for external and internal turning Consistent seating and predictable cutting behaviour for steady production The rhombic 80° profile and ISO dimensions ensure fast, repeatable seating in compatible holders; the 4.76 mm thickness and standard 12 mm size give mechanical stability during interrupted cuts. Because compatibility depends on form, clearance, tolerance class, fastening and thickness, the ISO conformity materially reduces setup time and rejects related to misfit. This stability translates into fewer tool changes and smoother cycle times for turning operations. Balanced cutting performance driven by the FX105 grade The FX105 grade contributes a deliberate balance of wear resistance and toughness, extending edge life without sacrificing reliability in tougher cutting conditions. Manufactured in cemented carbide, the grade supports consistent flank condition and reduces unexpected edge chipping. For turning applications, this balance helps maintain dimensional accuracy over longer tool life, supporting predictable component quality in medium to high volume production. Stable chip formation and process security With no integrated chipbreaker specified, the selection of an appropriate chip control geometry and a matching holder becomes decisive. The insert’s 0.8 mm corner radius promotes a robust cutting edge, improving resistance to micro‑fracture and supporting consistent chip formation, particularly when combined with suitable feeds and insert clamping. The system build typically consists of the ISO insert, an appropriate external holder or boring bar, an underlay/clamping set and replacement screws to ensure robust assembly and repeatable clamping force. Practical application advice for workshop planners Ideal for a broad range of turning tasks, these ISO indexable inserts fit into established tooling systems and spare‑parts logistics. Match the FX105 grade and edge geometry to the workpiece material and cutting conditions to exploit the insert’s strengths: long life under steady loads and resilience under variable conditions. The insert’s ISO designation simplifies stock management and replacement routines, helping to reduce downtime and maintain throughput. Secure original Tungaloy CNMN120408 FX105 inserts through Metav Werkzeuge for dependable turning performance — contact Metav Werkzeuge for technical guidance or to place an order via info@metav-werkzeuge.com or +49 2822 7131930 Technical Data Article number: 6802362 Manufacturer SKU: TUN6802362 SKU: 6802362-Tungaloy Model series: ISO‑Drehwendeschneidplatten Core specifications Corner radius: 0.8 mm Thickness: 4.76 mm Size: 12 mm Clearance angle: 0° Insert angle: 80° Features & applications Material: cemented carbide Grade: FX105 (Tungaloy) Shape: rhombic Hole: without hole Chipbreaker: none Application: turning System components: ISO insert, suitable external holder or boring bar, underlay/clamping set, replacement screws FAQ What holder features must be checked for compatibility? Check holder form, clearance (free) angle, tolerance class, fastening type, insert size and thickness; the ISO‑compliant geometry of the insert facilitates compatibility with matching CNMN‑type holders. Which materials is the insert suitable for? The FX105 grade in cemented carbide is designed for turning operations; selection of chip control and cutting parameters should be matched to the specific workpiece material. How does the 0.8 mm corner radius affect tool life and finish? A 0.8 mm corner radius strengthens the cutting edge, improving resistance to micro‑fracture and aiding consistent surface finish under stable cutting conditions. Is a chipbreaker included with the insert? No chipbreaker is specified; chip control must be achieved by choosing a matching chipbreaker geometry or appropriate holder arrangement for the intended application. How is the insert supplied and what additional parts are typically required? The CNMN120408 FX105 insert is an ISO indexable plate; a compatible external holder or boring bar, underlay/clamping set and replacement screws are normally required for a complete tooling setup. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
CNMN 120412 FX105 Wendeplatten - Tungaloy
Take advantage of the ISO conformity, robust FX105 grade and precise 1.2 mm nose radius for consistent turning results and economical tool life — order genuine inserts through Metav Werkzeuge or consult our specialists for application support. CNMN 120412 FX105 turning insert (ISO rhombic, 12 mm) by Tungaloy — 0° relief, 1.2 mm nose radius CNMN 120412 FX105 is an ISO-standard indexable turning insert for general external and internal turning operations, designed to match holders by form, relief angle, tolerance class, fastening, size and thickness. ISO rhombic insert CNMN 120412 FX105 1.2 mm nose radius for precise profiles 0° relief for robust cutting Cemented carbide body, thickness 4.76 mm Predictable compatibility and reliable clamping for workshop workflows The ISO designation and standardised geometry ensure straightforward integration into recognised holder systems; ISO conformity reduces setup uncertainty and supports reproducible results across shifts. The insert’s rhombic form and specified thickness mean that clamping behaviour is predictable, which translates into fewer micro-adjustments at the machine and less downtime. For production planning, this stability simplifies tooling lists and minimises the need for multiple corrective test cuts. Balanced cutting performance from the FX105 carbide grade The FX105 grade combines wear resistance, toughness and edge stability to complement the chosen geometry; this balance is intended to maintain cutting-edge integrity over longer tool life while avoiding brittle failure. In practical terms, the cemented carbide construction gives a good compromise between life and versatility, making the insert suitable for a broad range of turning tasks when the correct chipformer and grade are selected. This results-focused combination helps to lower overall machining costs by reducing insert change frequency and improving process repeatability. Practical geometry for accurate profiles and simplified tool management A 1.2 mm nose radius delivers defined part contours while retaining sufficient edge strength for semi-finishing and profiling. The 0° relief supports robust engagement in many turning set-ups and the 12 mm size provides a familiar reference for pocketing and holder selection. As an ISO indexable solution, the system approach — insert, holder, clamp and screw — streamlines spare-part handling and inventory. For questions on matching holders or adapting cutting data, technical guidance is available to ensure the insert is used in the most productive way. Contact Metav Werkzeuge for tailored application advice and to source genuine Tungaloy CNMN120412 FX105 turning inserts — eMail info@metav-werkzeuge.com or call +49 2822 7131930 Technical Data Article number: 6802363 Manufacturer SKU: TUN6802363 Model series: ISO-Drehwendeschneidplatten Material: cemented carbide Designation: CNMN120412 FX105 Tungaloy-Wendeplatte Core specifications Radius: 1.2 mm Thickness: 4.76 mm Size: 12 mm Relief angle: 0° Included angle: 80° Special features Grade: FX105 Shape: rhombic Hole: without hole Application: turning FAQ What determines whether this insert fits a given holder? Compatibility is defined by form, relief angle, tolerance class, fastening, size and thickness; the ISO designation helps match inserts to compatible holders. Which turning operations are intended for this grade? The FX105 grade and rhombic geometry are intended for both external and internal turning; selection of a suitable chipformer and cutting data depends on part material and stability of the set-up. Is the insert suitable for interrupted cuts? The grade’s balance of wear resistance and edge stability supports demanding conditions, making it appropriate for many interrupted-cut scenarios when used with a suitable toolholder and parameters. Does this insert have a central hole for screw fastening? This variant is specified as without hole, so it is clamped in holders designed for holeless rhombic inserts. How does the 1.2 mm nose radius affect surface finish and strength? A 1.2 mm radius offers a compromise between detail definition and edge strength, producing reliable profiles while maintaining resistance to edge chipping. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
CNMX 120716 FX105 Wendeplatten - Tungaloy
Take advantage of a proven, ISO‑compliant turning solution that combines FX105 cutting grade performance with robust carbide construction and a versatile 1.6 mm corner radius for consistent productivity; order the insert directly via Metav Werkzeuge or consult their team for compatibility and delivery. CNMX120716 FX105 turning insert (ISO rhombic, 80°) by Tungaloy CNMX120716 FX105 is an ISO‑standard rhombic turning insert designed for external and internal turning, offering a balance of wear resistance and edge stability for a wide range of turning tasks. ISO rhombic insert CNMX 120716 FX105 Tungaloy FX105 carbide grade 80° geometry for stable turning 1.6 mm corner radius for versatility Predictable wear life and material performance The FX105 grade, combined with a carbide substrate, delivers a targeted mix of wear resistance and toughness that stabilises cutting edges and extends tool life under typical turning loads. This translates into fewer indexings and less frequent insert changes, improving machine uptime and process economy. The cutting material is engineered for stable chip formation and consistent wear behaviour, which supports repeatable component quality and reduced scrap rates. Emphasis on measurable performance means process planners can rely on the insert for steady productivity rather than guesswork. Geometry engineered for stable turning and compatibility With an 80° included angle and a 1.6 mm corner radius, the rhombic form provides a compromise between edge strength and accessibility in confined geometries. The insert thickness of 7.94 mm and nominal plate size 12 contribute to rigidity when paired with the correct holder and clamping set. Compatibility is determined by form, clearance angle, tolerance class, fastening, size and thickness; matching the insert to a suitable external holder or boring bar and the correct underplate/clamp ensures secure seating and repeatable positioning during machining. These characteristics reduce vibration and support improved surface finish with predictable chip control. Practical selection and application guidance for production This ISO turning plate is intended for general turning operations where a versatile, reliable insert is required. Select a chipbreaker and grade that suit the workpiece material and the machine‑tool setup; the FX105 variant complements geometrical choice by providing balanced edge stability for mixed materials. For unstable setups or heavy interrupted cuts, opt for more robust clamping and consider a smaller positive approach to reduce cutting forces. For fine finishing passes, the geometry and grade combination supports good surface integrity and dimensional stability. If additional machining parameters or test results are required, technical data and selection assistance are available to support process optimisation. Contact Metav Werkzeuge for tailored advice on holder compatibility, availability of the CNMX120716 FX105 turning insert and delivery options — email info@metav-werkzeuge.com or call +49 2822 7131930 Technical Data Article number: 6825655 Manufacturer SKU: TUN6825655 Manufacturer item number: 6825655 Facts Corner radius: 1.6 mm Thickness: 7.94 mm Included angle: 80° ISO code: 120716 Plate size: 12 Clearance angle: 0° Special features Material: carbide Coating / grade: FX105 (Tungaloy) Plate form: rhombic Application: turning (external and internal) Model series: ISO turning inserts Hole style: special Chipbreaker: special FAQ What materials is this insert suitable for? The CNMX120716 FX105 turning insert with FX105 grade is designed for a broad range of materials; pairing grade and chipbreaker to the specific workpiece ensures optimal wear resistance and edge stability. How does the 80° geometry affect cutting performance? An 80° rhombic geometry increases edge strength and improves stability in straight and light profiling cuts, helping the insert maintain dimensional accuracy during conventional turning operations. Which holder features are required for correct compatibility? Compatibility depends on holder form, clearance angle, tolerance class, fastening method, size and thickness; ensure the selected external holder or boring bar matches the insert’s ISO dimensions and clamping arrangement. Is the insert suitable for finishing and roughing? The combination of FX105 grade and a 1.6 mm corner radius offers flexibility for both finishing and lighter roughing; for heavy roughing, confirm machine rigidity and consider a more robust setup. What information is included with the insert for installation? The insert is supplied as an ISO plate intended for use with an appropriate holder, underplate/clamp and replacement screws; verify clamping parts and tolerance class for a secure fit. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
CPGA 090202 DX140 Wendeplatten - Tungaloy
Combine the DX140 PCD cutting grade with a 0.2 mm corner radius and 11° clearance to achieve high cutting speeds and extended runtimes when machining aluminium and other non-ferrous alloys. The ISO-compatible geometry and secure cylindrical hole ensure reliable clamping and repeatable results. Order the insert directly via Metav Werkzeuge or consult our specialists for application advice. CPGA090202 DX140 ISO turning insert (PCD) — Tungaloy The CPGA090202-DIA DX140 is an ISO-standard PCD turning insert engineered for external and internal turning of aluminium, non-ferrous alloys and abrasive non-metallic materials. PCD grade DX140 for aluminium and non-ferrous metals ISO rhombic insert CPGA090202 with 0.2 mm radius 11° clearance, 80° included angle for stable cutting Cylindrical hole and 2.38 mm thickness for secure clamping High-speed cutting and longer tool life for non‑ferrous machining The combination of DX140 and PCD (polycrystalline diamond) cutting material provides a decisive advantage when turning aluminium and similar alloys: high cutting speeds with markedly reduced wear. The PCD cutting edge resists abrasive inclusions and keeps its geometry longer than conventional carbide grades, which translates into fewer indexings and longer uninterrupted production runs. For workshops seeking process stability and predictable tool consumption, this cutting grade delivers improved component consistency and lower overall tooling cost per part. Secure clamping and precision geometry for consistent surface quality A stable tool–holder interface and well-defined geometry are essential for achieving repeatable results. The rhombic CPGA shape with an 80° included angle and 11° clearance combines rigidity with accessibility for external and internal operations. The 0.2 mm radius supports fine finishing and controlled chip formation, while the 2.38 mm plate thickness and cylindrical hole ensure secure clamping in standard ISO holders. The insert’s carbide substrate provides the requisite backing strength for the PCD layer, enabling safe high‑speed engagement and consistent surface finish. System compatibility and application guidance for reliable production Compatibility with a holder depends on form, clearance angle, tolerance class, fastening, size and thickness; the ISO designation simplifies selection across standard toolholders. The recommended system comprises an ISO insert, a matching external holder or boring bar, a suitable shim/clamp set and replacement screws. Select the DIA chipbreaker and DX140 grade according to workpiece material, machining strategy and machine stability to optimise performance. For specific setups or to verify suitability for a given cycle, the CPGA090202-DIA plate integrates easily into existing tool‑holding systems and contributes to predictable tool life and reduced downtime. For further technical data and availability contact Metav Werkzeuge at info@metav-werkzeuge.com or call +49 2822 7131930. For application-specific recommendations or to order genuine Tungaloy CPGA090202-DIA DX140 inserts, contact Metav Werkzeuge for precise technical advice and fast supply. Technical Data Article number: 6802376 SKU: 6802376-Tungaloy Manufacturer SKU: TUN6802376 Model series: ISO-Drehwendeschneidplatten Brand: Tungaloy Facts Corner radius: 0.2 mm Included angle: 80° Clearance angle: 11° Plate thickness: 2.38 mm Plate size: 09 Special features Cutting material: polycrystalline diamond (PCD), grade DX140 Substrate material: carbide Application: turning (external and internal) Chipbreaker: DIA Hole style: cylindrical hole Plate form: rhombic FAQ What materials is this insert designed for? The CPGA090202-DIA DX140 insert is designed primarily for aluminium, non‑ferrous metals and abrasive non‑metallic materials where PCD cutting edges offer superior wear resistance. How does the DX140 grade improve productivity? DX140 provides extended tool life and allows high cutting speeds, reducing the frequency of insert changes and improving overall machining throughput with stable performance. Is the insert compatible with standard ISO holders? Yes, the CPGA090202‑DIA follows ISO geometry; compatibility depends on form, clearance angle, tolerance class, fastening method, size and thickness of the holder. Which chipbreaker should be chosen for general aluminium turning? The DIA chipbreaker supplied with this insert is optimised for aluminium and similar materials; selection should match the workpiece alloy and machining stability for best results. Can this insert be used for internal boring as well as external turning? Yes, the rhombic CPGA shape and specified geometry enable use in both external and internal turning applications when mounted in a suitable holder. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
CPGA 090204 BX360 Wendeplatten - Tungaloy
Taking advantage of a CBN-grade cutting edge, a compact 0.4 mm corner radius and ISO conformity, this insert delivers consistent finishing on hardened steels while reducing tool-change frequency and process variation; order the CPGA090204 BX360 directly via Metav Werkzeuge or ask our consultants if technical advice is required. CPGA 090204 BX360 indexable turning insert by Tungaloy — CBN grade for hardened steels, 11° clearance CPGA090204 BX360 is an ISO-formatted indexable turning insert designed for finishing operations on hardened steels and, depending on selection, certain cast irons CBN cutting material for hard machining ISO interchangeability for rapid tool setup Rhombic shape with 0.4 mm corner radius 11° clearance, 80° included angle High-performance finishing with cubic boron nitride The BX360 grade utilises CBN (cubic boron nitride) as the cutting material to provide superior wear resistance and thermal stability in the machining of hardened steels. CBN is a superabrasive tailored for high-hardness workpieces: it maintains edge integrity where conventional carbide would wear rapidly. The result is more consistent surface quality and longer intervals between index changes, which supports predictable cycle times and reduces unplanned downtime. Reliable ISO compatibility for straightforward integration Built to the ISO turning insert family, this rhombic component guarantees dimensional and tolerance conformity; compatibility with a turning toolholder depends on form, 11° clearance, tolerance class, fastening method, size and thickness. The standardised format simplifies tool-pool management and stock rotation, allowing production planners to specify the insert with confidence and to match it with existing holders without ambiguity. Precision geometry for repeatable surface results A 0.4 mm corner radius and 80° included angle produce a controlled cutting edge suited to fine finishing passes. The modest radius supports tight dimensional control and a consistently fine surface texture, while the 2.38 mm thickness and secure locating hole ensure stable seating during turning. The rhombic form with a cylindrical hole provides reliable clamping and repeatability, reducing vibration-related variations in finish and dimensional accuracy. Application guidance and selection strategy Intended primarily for turning applications on hardened materials, the insert performs best when matched with a holder and machining parameters that reflect part rigidity and cutting conditions. Select the appropriate grade and, where available, a chip former according to workpiece material and process stability; for unstable setups, prefer a more robust clamping arrangement or reduced depths of cut to preserve edge life. For complex assemblies or atypical materials, technical advice is available to align grade choice with productivity goals. Contact Metav Werkzeuge for application guidance on the Tungaloy CPGA090204 BX360 insert and for ordering information — phone +49 2822 7131930 or email info@metav-werkzeuge.com Technical Data Article number: 6802378 Manufacturer SKU: TUN6802378 SKU: 6802378-Tungaloy Designation: CPGA090204 BX360 Model series: ISO turning indexable inserts Material: carbide Grade: BX360 (CBN) Facts Corner radius: 0.4 mm Thickness: 2.38 mm Size: 09 Included angle: 80° Clearance angle: 11° Hole: with hole Hole style: cylindrical Special features Rhombic insert shape CBN cutting material Intended for hardened steels and, depending on grade, cast iron ISO-standardised indexable format No chipbreaker specified FAQ What materials is this insert designed to machine? The CPGA090204 BX360 Tungaloy indexable turning insert is formulated primarily for hardened steels and, depending on the exact grade application, can be used for certain cast irons. How is compatibility with a toolholder determined? Compatibility is governed by insert form, clearance angle (11°), tolerance class, fastening method, size (09) and thickness (2.38 mm); the ISO format facilitates matching with standard holders. What does the BX360 designation indicate? BX360 denotes the CBN-based grade chosen for high hardness machining; it emphasises wear resistance and thermal stability for finishing cuts on hardened workpieces. Which edge geometry suits finishing operations? A 0.4 mm corner radius offers controlled cutting for fine surface finishes and tight dimensional tolerances; pairing this geometry with stable clamping enhances repeatability. What identifiers should be quoted when ordering? Use the manufacturer article number 6802378 and SKU 6802378-Tungaloy (manufacturer SKU TUN6802378) when ordering or requesting tooling advice. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
CPGA 090204 DX140 Wendeplatten - Tungaloy
Benefit from high cutting speeds and extended tool life thanks to the DX140 PCD grade and the ISO CPGA090204 geometry; compatibility with ISO toolholders is ensured by the rhombic 80° form, 11° clearance and 2.38 mm thickness. Order the insert directly via Metav Werkzeuge or ask the consultants for application support. CPGA090204 DX140 Tungaloy Turning Insert (PCD, ISO rhombic 80°) The CPGA090204 DX140 is an ISO-formatted rhombic turning insert designed for high-speed machining of aluminium and other non-ferrous and abrasive non-metal materials. PCD grade DX140 for long tool life ISO CPGA090204 rhombic 80° geometry Suited to aluminium and non-ferrous metals Cylindrical hole for secure mounting High productivity from PCD technology The use of polycrystalline diamond (PCD) in the DX140 grade delivers a combination of extreme wear resistance and consistent edge stability that directly increases machining throughput. PCD is a synthetic diamond layer sintered onto a carbide substrate; this structure provides superior abrasion resistance compared with conventional carbide grades, which means longer tool life and fewer indexings in serial production. For components made from aluminium or other non-ferrous alloys and abrasive composites, this results in reduced downtime and more predictable cycle times. Secure fit and ISO-compatibility for reliable set-up Compatibility with toolholders is determined by geometry, clearance and thickness. The insert follows the ISO CPGA090204 form, presenting an 80° rhombic shape, a 11° clearance angle and a plate thickness of 2.38 mm, which together ensure reliable seating in standard ISO holders. The cylindrical hole provides positive mechanical location and stable clamping, reducing the chance of insert movement under high cutting forces. Because these dimensions conform to ISO norms, integration into existing tool systems is straightforward and reduces the need for special adapters. Consistent surface quality and process reliability A PCD cutting edge delivers an excellent surface finish on light alloys by producing fine, short chips and limiting built-up edge. The DX140 grade is optimised for high-speed turning and maintains a sharp, durable cutting line even under abrasive conditions, supporting consistent dimensional accuracy and repeatable component quality. The carbide substrate under the diamond layer provides the rigidity needed for stability during feed changes and interrupted cuts, while the PCD face sustains low wear rates across long production runs. Practical selection and system considerations For general turning, a 0.4 mm corner radius offers a balance between edge strength and form fidelity; it resists chipping while still enabling fine profile work where small radii are required. Note that this insert is supplied without a chipbreaker, so chip control must be achieved via tooling geometry, feed selection and holder choice. A complete cutting system typically includes the ISO turning insert, a matching external holder or boring bar, a shim/clamping kit and replacement screws. When matching holders, ensure form, clearance, tolerance class, attachment and thickness are aligned with the ISO specification for dependable performance. Contact Metav Werkzeuge for tailored application advice on the Tungaloy PCD turning insert CPGA090204 DX140, or call +49 2822 7131930 / email info@metav-werkzeuge.com to discuss suitability for specific materials and cycle requirements Technical data Article number: 6802377 SKU: 6802377-Tungaloy Manufacturer SKU: TUN6802377 Model series: ISO turning inserts Measurements Thickness: 2.38 mm Corner radius: 0.4 mm Clearance angle: 11° Insert angle: 80° Size: 09 Design / Material / Application Material: Carbide substrate Cutting material: PCD (polycrystalline diamond), grade DX140 Shape: Rhombic with cylindrical hole Chipbreaker: without Application: Turning FAQ What materials is this insert best suited for? The CPGA090204 DX140 insert is designed for aluminium, other non-ferrous metals and abrasive non-metal materials; the PCD grade provides excellent wear resistance for these applications. Is the insert compatible with standard ISO holders? Yes. The insert follows the ISO CPGA090204 form with an 80° rhombic geometry, 11° clearance and a 2.38 mm thickness, allowing use in compatible ISO toolholders. Why choose a 0.4 mm corner radius? A 0.4 mm corner radius balances edge robustness and detail reproduction, offering resistance to chipping while still enabling accurate profiling in turning operations. Does the insert include a chipbreaker? This variant is supplied without a chipbreaker; chip control should be achieved through holder geometry, feed rate and process parameters. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
CPGA 090208 BX360 Wendeplatten - Tungaloy
Take advantage of a high‑performance CBN grade for reliable finishing of hardened steels and the ISO form that ensures straightforward holder compatibility; combine these properties with Tungaloy's proven grade design for fewer tool changes and stable batch production. Order the insert directly via Metav Werkzeuge or consult our specialists for application support. CPGA 090208 BX360 CPGA090208-QBN — Tungaloy ISO turning insert for turning, CBN for hardened steels, 80° the CPGA090208-QBN BX360 is an ISO‑standard rhombic turning insert designed for finishing and hard turning applications where wear resistance and edge stability are essential CBN grade BX360 for hardened steel machining Rhombic 80° geometry for versatile turning 11° clearance angle for secure cutting action Cylindrical hole for reliable mounting Increase uptime with a wear‑resistant CBN solution The BX360 grade uses cubic boron nitride (CBN) to deliver superior abrasion resistance in hard finishing operations. This results in longer tool life and more consistent component tolerances, reducing the frequency of insert changes and machine downtime. For production environments working with high‑hardness steels, the switch to a CBN finishing insert provides measurable gains in process stability and surface quality without complex requalification of the machining cell. Fast, reliable fitting for proven productivity gains As an ISO turning insert, compatibility with holders depends on form, clearance angle, tolerance class, fixing method, size and thickness. The rhombic shape with an 80° included angle, 11° clearance, and a 0.8 mm corner radius enables straightforward mounting in standard external holders or boring bars. The insert's cylindrical hole ensures repeatable clamping; combined with the standardised dimensions, this reduces setup time and simplifies tool inventory management, supporting leaner workshop logistics. Optimised for hardened steels and demanding finish passes The cutting material and chipbreaker selection make this insert particularly suitable for hardened steel finishing and—depending on the variant—certain cast iron operations. The CBN cutting edge maintains a sharp profile under high abrasion, producing finer surface finishes and stable dimensional results. Select the QBN chipbreaker and the appropriate grade variant to match workpiece hardness, cutting direction and machine rigidity to achieve the best balance between life and surface integrity. Practical system advice for consistent results An efficient cutting system consists of the ISO insert, a matching external holder or boring bar, a correct underlay/clamp set and spare fixing screws. Given the insert's 2.38 mm thickness and ISO size 09, choose a holder with matching pocket clearance to preserve tolerance and edge support. For process optimisation, combine the grade's strengths with stable clamping and conservative approach parameters when first introducing CBN into a cycle; once proven, the grade typically supports increased cutting speeds and fewer interventions. For demanding hard‑turning tasks, choose the Tungaloy BX360 CPGA insert and contact Metav Werkzeuge for personalised application advice and rapid supply Technical data Article number: 6802379 Manufacturer SKU: TUN6802379 Merchant SKU: 6802379-Tungaloy Model series: ISO‑Drehwendeschneidplatten Material: carbide Grade: BX360 Chipbreaker: QBN Application: Turning Core specifications ISO designation: CPGA090208-QBN Insert size: 09 Plate thickness: 2.38 mm Included angle: 80° Clearance angle: 11° Corner radius: 0.8 mm Manufacturer article number: 6802379 Special features Rhombic plate form Cylindrical hole for fixing Designed for hardened steel finishing Compatible with standard ISO holders Tungaloy grade BX360 with CBN cutting material FAQ What materials is this insert designed for? The CPGA090208‑QBN BX360 insert is engineered primarily for hardened steels, with certain BX360 variants also suitable for specified cast iron applications. How does the CBN cutting material benefit finishing operations? CBN in the BX360 grade gives high abrasion resistance and edge stability, allowing the insert to maintain surface quality and dimensional accuracy over longer production runs. Which holder features are required for correct fitting? A standard ISO external holder or boring bar with matching pocket geometry, correct clamp/underlay set and screw fixation is required to secure the CPGA insert and ensure repeatable performance. Is the corner radius suitable for fine finishing? The 0.8 mm corner radius provides a compromise between edge strength and achievable surface finish, making it suitable for many finishing passes on hardened components. Can this insert reduce overall machining time? By offering extended edge life and consistent cutting behaviour, the BX360 CBN insert can reduce tool changes and improve process stability, contributing to reduced overall machining interruptions. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
CPGT 050202 NS9530 Wendeplatten - Tungaloy
Combine the sharp cutting edge of the uncoated NS9530 cermet with the ISO‑standard rhombic geometry for reliable finishing in turning operations; the low cutting forces and controlled chip formation support consistent surface quality and productivity. Order the insert directly via Metav Werkzeuge or contact our consultants for tailored cutting data. CPGT 050202 NS9530 — Turning insert (rhombic, 11° clearance) by Tungaloy CPGT 050202 NS9530 is an ISO‑standard rhombic turning insert designed for finishing steel with a sharp cutting edge and low cutting forces ISO‑standard rhombic insert, size 05 Uncoated cermet grade NS9530 for finishing Sharp cutting edge for low cutting forces Cylindrical hole with single‑side countersink Consistent finishing performance for turning operations The CPGT insert combines an ISO‑compliant geometry with a sharp cutting edge to deliver high surface quality on continuous cuts and small depths of cut. The uncoated cermet grade NS9530 is optimised for finishing steel, offering low cutting forces that reduce vibration and improve dimensional stability. This results in fewer reworks and more predictable part quality when turning external or internal diameters. Designed for secure clamping and compatibility The rhombic plate form and the built‑in hole arrangement ensure consistent seating and repeatable positioning in compatible holders and boring bars. The insert fits holders according to ISO form, clearance, tolerance class, fixing method, size and thickness; the cylindrical hole with one‑side countersink (40°–60°) secures the insert against rotation while maintaining a compact clamping stack. Users benefit from straightforward tool assembly and reproducible set‑ups, which reduces machine downtime and simplifies tool inventory management. Material behaviour and process advantages Made on a cemented carbide body with an uncoated cermet cutting layer, the grade provides stable chip formation and a fine cutting edge that excels in finishing passes. The small corner radius (0.2 mm) and 11° clearance angle promote low cutting resistance and superior surface finish, especially on continuous feed operations. The W15 chipbreaker supports predictable chip control in finishing applications, contributing to efficient swarf evacuation and consistent tool life under recommended cutting conditions. For advice on speeds and feeds for specific steels, technical consultation is available. For precise finishing in turning, choose the Tungaloy NS9530 insert and contact Metav Werkzeuge for availability and application advice (info@metav-werkzeuge.com / +49 2822 7131930) Technical Data Article number: 6997915 Manufacturer SKU: TUN6997915 SKU: 6997915-Tungaloy Name: CPGT050202L-W15 NS9530 ISO designation: 050202 Core measurements Size: 05 Thickness: 2.38 mm Corner radius: 0.2 mm Clearance angle: 11° Insert angle: 80° Shape: rhombic Hole: with hole; cylindrical hole + one‑side countersink (40°–60°) Design and special features Grade: NS9530 Chipbreaker: W15 Schneidstofftyp: uncoated cermet Application: Turning Intended use: finishing on steel System setup: ISO insert, matching external holder or boring bar, support/clip set and spare screws FAQ What applications suit this insert best? The CPGT 050202 NS9530 turning insert is intended for external and internal turning finishing passes, especially where low cutting forces and high surface quality are required. Which materials can be machined with this grade? The NS9530 uncoated cermet is optimised for finishing steel and provides stable chip formation and a sharp cutting edge for continuous cutting operations. How does the chipbreaker influence machining? The W15 chipbreaker promotes predictable chip control during finishing, aiding evacuation and reducing the risk of surface damage during turning. What clamping features ensure repeatability? The insert’s rhombic form combined with the cylindrical hole and single‑side countersink (40°–60°) secures the plate reliably in ISO‑compatible holders for repeatable seating and positioning. Which product identifiers should be used when ordering? Order using article number 6997915 or SKU 6997915‑Tungaloy and specify the designation CPGT050202L‑W15 NS9530 to ensure the correct uncoated cermet finishing insert is supplied. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
CPGT 050204 NS9530 Wendeplatten - Tungaloy
Take advantage of the combination of uncoated cermet NS9530 for superior surface finish and the ISO‑standard CPGT050204 form for straightforward holder compatibility to ensure efficient finishing operations; order directly via Metav Werkzeuge or contact our consultants for application advice. CPGT050204L‑W15 NS9530 — Indexable turning insert (finishing), Tungaloy The Tungaloy CPGT050204L‑W15 NS9530 is an ISO‑format indexable insert designed for precision external and internal turning, optimised for finishing steel with continuous cuts and small depths of cut. Uncoated cermet grade NS9530 for fine finishing Sharp cutting edge for low cutting forces ISO CPGT050204 form for standard holder fit Cylindrical hole with 40°–60° single‑side countersink High‑precision finishing for steel turning The insert is engineered as a finishing grade for steel: the NS9530 uncoated cermet combines a sharp cutting edge with low cutting forces to deliver improved dimensional control and high surface quality. In continuous cutting conditions and when using small depths of cut, the cutting geometry reduces vibration and minimises the need for secondary operations. The combination of the fine cutting edge and the W15 chipbreaker yields consistent chip formation and contributes to productive turning cycles in series production or small‑batch finishing. Easy integration with ISO systems and secure clamping The ISO designation CPGT050204 indicates compatibility with standard external holders and boring bars when the holder matches in form, clearance angle, tolerance class, fastening method, size and thickness. Key geometry figures—11° clearance angle, 0.4 mm corner radius and 2.38 mm plate thickness—define the working profile and must be matched to the toolholder. The insert comes with a cylindrical hole and a single‑sided countersink (40°–60°) for reliable centring and screw clamping; the system typically comprises the ISO insert, a matching external holder or boring bar, a support/clamping kit and replacement screws for maintenance and quick changeover. Practical process guidance and benefits for workshops For finishing applications, select the W15 chipbreaker and align the insert's geometry with the machine stability and workpiece material to exploit the low cutting forces of the cermet grade. The sharp edge of the NS9530 grade promotes reduced cutting temperatures and finer surface finishes, which often shortens downstream dressing or polishing steps. Where improved throughput is a priority, the insert’s consistent edge preparation supports repeatable results and reduces rework, contributing to a more economical turning process and predictable component quality. For application advice, availability and to source this Tungaloy finishing insert through Metav Werkzeuge—contact info@metav-werkzeuge.com or call +49 2822 7131930 for fast, expert support and order processing Technical data Article number: 6997916 SKU: 6997916‑Tungaloy Manufacturer article number: 6997916 Model series: ISO‑turning indexable inserts Numbers / Core technical data Radius: 0.4 mm Plate thickness: 2.38 mm Clearance angle: 11° Insert angle: 80° Plate size: 05 Designs / Special features Uncoated cermet grade NS9530 Chipbreaker: W15 Plate form: rhombic Hole style: cylindrical hole + single‑side countersink (40°–60°) Typical use: external and internal turning, finishing steel System components: ISO insert, matching external holder or boring bar, support/clamping kit, replacement screws FAQ What materials is this insert intended for? The CPGT050204L‑W15 NS9530 insert is designated as a finishing grade for steel, optimised for continuous cuts and small depths of cut where a fine surface finish is required. Which toolholders are compatible with the ISO CPGT050204 form? Compatibility depends on matching the holder’s form, 11° clearance, tolerance class, fastening method, size and thickness; the ISO CPGT050204 designation ensures fit with standard external holders and boring bars designed for CPGT inserts. How does the W15 chipbreaker affect machining? The W15 chipbreaker promotes controlled chip formation in finishing cuts, supporting the NS9530 cutting edge to reduce cutting forces and improve surface integrity during continuous turning. Can this insert be used for internal turning (boring)? Yes, the insert is suitable for both external and internal turning when installed in the appropriate boring bar or holder that accommodates the ISO CPGT050204 geometry. Manufacturer/Responsible: Tungaloy‑NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand‑new product from the manufacturer.
CPGT 080202 NS9530 Wendeplatten - Tungaloy
Combining the sharp edge of the NS9530 uncoated cermet grade with a 0.2 mm nose radius and an 11° relief angle ensures low cutting forces, superior surface finish and consistent performance in finishing cuts on steel; order this insert directly via Metav Werkzeuge or consult our specialists for application support. CPGT 080202 NS9530 turning insert – uncoated cermet, rhombic 80° (Tungaloy) CPGT 080202 NS9530 is an ISO rhombic turning insert designed for finishing operations in external and internal turning, optimised for continuous cuts and small depths of cut. Uncoated cermet grade NS9530 0.2 mm nose radius for fine surface finish Rhombic ISO form CPGT 080202 Single-sided chipbreaker for finishing High finishing performance for steel and productivity gains The insert is engineered as a finishing grade for steel, delivering a combination of a very sharp cutting edge and low cutting forces. The NS9530 uncoated cermet substrate promotes a fine surface quality in continuous cutting conditions, making it particularly suitable where a superior finish and tight tolerances are required. Reduced cutting forces lower spindle loads and enable stable cutting at small depths of cut, which contributes to more predictable cycle times and an optimised production flow. Benefit statements are backed by the insert’s geometry: the 0.2 mm nose radius produces consistently small scallop heights while the sharp cermet edge reduces built-up edge formation on most steels. Precise geometry and reliable holder compatibility The ISO rhombic form and dimensional specifications ensure compatibility with standard indexable turning systems when matching is performed correctly. Compatibility to a holder is determined by form, relief angle, tolerance class, clamping and plate thickness; the insert’s 11° relief angle and 2.38 mm thickness are specified to fit corresponding ISO clamping systems. The product includes a cylindrical hole with a single-sided countersink (40°–60°), which provides repeatable clamping seating and simplifies repositioning during index changes. Using inserts with matching form and tolerance class reduces setup time and helps maintain consistent cutting conditions across repetitive operations. Material insight and recommended application approach The insert combines a carbide substrate body with an uncoated cermet cutting grade, optimised for finishing steel in turning. Cermet materials offer a hard, wear-resistant cutting edge and a tendency to deliver enhanced surface quality compared with many coated grades in finishing operations. Because the grade is designed for continuous feeds and small depths of cut, it is advised to select cutting parameters that avoid interrupted cuts and heavy feed spikes. The single-sided chipbreaker supports controlled chip formation in finishing ranges; for heavy or interrupted cuts, alternative chipbreakers or grades should be considered. Overall, the geometry and NS9530 grade deliver a balance of surface quality and tool life for precision turning tasks. For tailored advice on integrating the Tungaloy CPGT 080202 NS9530 insert into existing tool holders or production setups, contact Metav Werkzeuge via info@metav-werkzeuge.com or call +49 2822 7131930 for direct consultation and availability information Technical Data Article number: 6997917 SKU: 6997917-Tungaloy Manufacturer SKU: TUN6997917 Model series: ISO-Drehwendeschneidplatten Designation: CPGT080202 Key dimensions and numbers Nose radius: 0.2 mm Relief angle: 11° Plate thickness: 2.38 mm Size: 08 Included angle: 80° Design and features Rhombic plate form Uncoated cermet grade NS9530 Single-sided chipbreaker (finishing) Cylindrical hole + single-sided countersink (40°–60°) Suitable for external and internal turning (finishing) Compatibility determined by form, relief angle, tolerance class, clamping, size and thickness FAQ Which materials is this insert intended for? The CPGT 080202 NS9530 insert is designed primarily for finishing on steel; the uncoated NS9530 cermet grade excels in continuous cuts that require high surface quality. What holder features are required for correct compatibility? Compatibility depends on matching the insert’s ISO form, 11° relief angle, tolerance class, clamping arrangement and 2.38 mm thickness to the turning holder; the insert’s cylindrical hole with countersink ensures secure seating. Can this insert be used for internal turning? Yes, the ISO rhombic form and dimensions permit use in both external and internal turning applications where finishing cuts are required. How does the NS9530 grade affect tool life and finish? The NS9530 uncoated cermet provides a sharp, wear-resistant edge that typically yields superior surface finish and stable performance in continuous finishing operations on steel. What is the SKU and article number for ordering reference? Use SKU 6997917-Tungaloy or article number 6997917 when enquiring about the CPGT080202 NS9530 Tungaloy turning insert. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
CPGT 080202 TH10 TH10 Wendeplatten - Tungaloy
Take advantage of the combination of a sharp, uncoated carbide grade and ISO‑standard geometry for reliable low‑force turning and clean surface results; order the insert directly via Metav Werkzeuge or contact the consultants for technical advice. CPGT080202 TH10 turning insert by Tungaloy — rhombic 80°, 0.2 mm radius A CPGT080202 TH10 rhombic turning insert designed for external and internal turning, offering a sharp, uncoated carbide grade optimised for non‑ferrous materials and applications that require low cutting forces and good surface finish. Rhombic CPGT insert, 80° geometry TH10 uncoated carbide for non‑ferrous materials 0.2 mm corner radius for fine surface finish Cylindrical hole with 40°–60° countersink Consistent chip control for productive non‑ferrous turning The TH10 uncoated carbide grade provides a sharp cutting edge that keeps cutting forces low and supports clean chip formation when machining aluminium, brass and similar materials. The rhombic 80° geometry combined with an 11° clearance angle and a single‑sided chipbreaker helps maintain stable cutting conditions during both roughing and light finishing cuts. As an ISO‑standard insert, the component integrates into common holder systems; compatibility is determined by form, clearance, tolerance class, fastening, size and thickness so tool selection can be matched to the machining setup for consistent productivity. Achieve finer surfaces with a small corner radius A 0.2 mm corner radius produces a balance between edge strength and surface quality, permitting smoother finishes without sacrificing repeatability. The plate’s 2.38 mm thickness contributes to rigidity at the cutting edge, which reduces vibration in shorter overhang set‑ups and improves dimensional control in turned features. For customers seeking better surface integrity on external diameters or inside bores, the combination of a sharp uncoated grade and a small radius reduces the tendency for built‑up edge, making it suitable for finishing passes where low cutting forces and crisp profiles are required. Easy mounting and ISO‑based compatibility for efficient tool management The insert features a cylindrical hole with a one‑sided countersink (40°–60°) to ensure secure retention in compatible clamps and underplates, allowing fast index changes and minimal downtime. As part of an ISO‑standard insert system, the item is straightforward to stock and replace across workshops that use matched external holders and boring bars. Clear labelling and standard geometry simplify tool inventory and reordering; when toolholders are selected to match form, free angle and tolerance class, the result is reliable repeatability and reduced setup times for series production. For dependable high‑throughput turning with clean surface results, contact Metav Werkzeuge for availability and expert guidance on the Tungaloy CPGT080202 TH10 insert — email info@metav-werkzeuge.com or call +49 2822 7131930 to discuss suitability for specific applications. Technical data Article number: 6802389 Manufacturer SKU: TUN6802389 Our SKU: 6802389-Tungaloy Model series: ISO turning indexable inserts Material: carbide Facts Corner radius: 0.2 mm Plate thickness: 2.38 mm Insert geometry angle: 80° Clearance angle: 11° Size: 08 Countersink angle: 40°–60° Special features Grade: TH10, uncoated carbide Shape: rhombic Hole: cylindrical with one‑sided countersink Chipbreaker: single‑sided Application: turning (external and internal) Compatibility: ISO‑standard; depends on holder form, clearance, tolerance, fastening, size and thickness FAQ What materials is this insert best suited for? The CPGT080202 TH10 insert by Tungaloy is a sharp, uncoated carbide grade optimised for non‑ferrous materials such as aluminium, brass and many plastics, where low cutting forces and clean chips are priorities. Which turning operations are appropriate for this insert? This rhombic ISO insert is intended for both external and internal turning operations, providing good performance for finishing and light‑to‑medium roughing when paired with the right holder and cutting parameters. How is the insert secured in the toolholder? The insert has a cylindrical hole with a one‑sided countersink (40°–60°) that allows secure clamping in compatible holders; correct matching of holder form, free angle and tolerance class is essential for stable seating and repeatability. How does the uncoated TH10 grade affect cutting behaviour? The uncoated TH10 carbide delivers a sharp edge that minimises cutting forces and reduces built‑up edge on softer, non‑ferrous alloys; it is designed for clean finishes rather than extreme wear resistance required for hard or abrasive materials. Is this insert suitable for finishing passes? Yes — the 0.2 mm corner radius and sharp uncoated grade support improved surface integrity on finishing passes while maintaining adequate edge strength for repeatable results. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand‑new product from the manufacturer.
CPGT 080202 TH10 Wendeplatten - Tungaloy
Take advantage of the sharp universal TH10 grade and the precise 80° rhombic geometry to achieve low cutting forces and consistently clean surfaces in non‑ferrous turning operations; order directly via Metav Werkzeuge or consult the team for holder compatibility and process optimisation. CPGT 080202 TH10 Turning insert for turning — Tungaloy (80° rhombic, 0.2 mm radius) The CPGT080202 TH10 is an ISO‑standard, rhombic indexable insert engineered for external and internal turning, offering a sharp, uncoated carbide cutting edge that supports low cutting forces and superior surface quality in non‑ferrous applications. ISO turning insert CPGT 080202 TH10 Rhombic 80° geometry, 0.2 mm nose radius Uncoated cemented carbide, sharp universal grade Cylindrical hole with 40°–60° countersink Consistent surface quality with a sharp universal grade The insert’s TH10 designation identifies a sharp, uncoated cemented carbide grade tailored for materials where a clean finish and low cutting force are priorities. An uncoated cutting edge reduces edge build‑up when machining soft, ductile workpiece materials, which in turn improves repeatability of surface finish and decreases the chance of smearing. For production environments that demand predictable results, the combination of a sharp grade and ISO conformity helps to maintain a reliable process window and reduces rework. Fast compatibility checks to reduce setup time As an ISO‑standard insert, compatibility is governed by geometry, clearance angle, tolerance class, fastening method, size and thickness. Selecting a matching holder and mounting hardware based on these criteria ensures correct seat and clamping, minimising runout and vibration. Clear guidance on holder type and a correct clamp sequence reduce setup time and support reproducible tool life, helping to keep cycle times predictable on batch and one‑off turning tasks. Geometry engineered for versatile chip control The 80° rhombic geometry combined with a 0.2 mm nose radius and an 11° clearance provides a balance between strength and fine finishing capability. The single‑sided chipbreaker manages chip formation during light to moderate depths of cut, improving evacuation in external and internal turning. The insert’s cylindrical hole with a 40°–60° countersink secures positive seating in a wide range of clamping systems, contributing to consistent cutting forces and safer chip flow. Material selection, system setup and common applications Made from cemented carbide, the insert is intended primarily for non‑ferrous materials and similar applications where an uncoated edge produces the desired surface and low cutting resistance. Typical system components include the ISO insert, a compatible external holder or boring bar, a backing pad/clamp and replacement screws. For workshops adapting the insert across diverse parts, the sharp grade and rhombic shape lend themselves to finishing passes, light semi‑finishing and profiling where geometric accuracy and surface appearance matter. For process assurance with Tungaloy's TH10 grade, contact Metav Werkzeuge to verify holder compatibility and secure the CPGT080202 insert for efficient non‑ferrous turning; eMail: info@metav-werkzeuge.com — Phone: +49 2822 7131930 Technical Data Manufacturer article number: 6802387 Manufacturer SKU: TUN6802387 Metav SKU: 6802387-Tungaloy Brand: Tungaloy Model series: ISO turning inserts Designation: CPGT080202 TH10 Core specifications Angle: 80° Nose radius: 0.2 mm Clearance angle: 11° Thickness: 2.38 mm Size: 08 Hole style: cylindrical hole + single‑side countersink (40°–60°) Chipbreaker: one‑sided Materials and features Material: cemented carbide Grade: TH10 (uncoated) Application: turning; external and internal turning System components: ISO insert, holder, shank, backing pad and screws Target workpiece materials: non‑ferrous materials Intended benefit: low cutting forces and clean surface finish FAQ What materials is this insert best suited for? The CPGT080202 TH10 insert from Tungaloy is optimised for non‑ferrous materials and similar applications where an uncoated, sharp edge reduces cutting forces and improves surface finish. How does the 80° rhombic shape affect machining? An 80° rhombic geometry increases versatility for external and internal operations, offering a compromise between cutting edge strength and the ability to achieve fine surface finishes with the CPGT080202. Which holders are compatible with this ISO insert? Compatibility depends on matching form, clearance angle, tolerance class, fastening and size; the insert seats in ISO‑compliant holders and is secured using the specified cylindrical hole with countersink. Can the TH10 grade be used for finishing operations? Yes, the TH10 sharp universal grade is suitable for finishing and light semi‑finishing where low cutting resistance and clean surface appearance are required. What is the manufacturer SKU for ordering? The manufacturer SKU is TUN6802387 and the Metav SKU is 6802387‑Tungaloy for the Tungaloy CPGT080202 TH10 turning insert. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
CPGT 080204 NS9530 Wendeplatten - Tungaloy
High-sheen finishing and low cutting forces are achieved by the combination of the uncoated NS9530 cermet grade and the rhombic 80° geometry with a precise 0.4 mm corner radius, enabling efficient continuous turning operations. Order the insert directly via Metav Werkzeuge or consult the technical team for tailored application advice. CPGT080204 NS9530 Tungaloy turning insert — ISO rhombic 80° · uncoated cermet The CPGT080204 NS9530 is an ISO rhombic turning insert designed for finishing turns on steel, offering a sharp cutting edge and predictable performance in continuous cuts. ISO rhombic insert CPGT 080204, 80° geometry Uncoated cermet grade NS9530 for finishing Sharp cutting edge for low cutting forces With central hole and 40°–60° countersink Consistent finishing for steel components The uncoated NS9530 grade is optimised for finishing of steel, delivering low cutting forces and an acute cutting edge that reduces workpiece distortion during light-pass turning. The rhombic 80° geometry, paired with a 0.4 mm corner radius, promotes stable contact conditions and a high-quality surface texture; this is particularly beneficial where dimensional accuracy and surface integrity are critical. The material combination of the cutting grade ensures a narrow range of chip formation, reducing vibration and improving repeatability in serial production. Process reliability and predictable tool life A finishing-oriented cermet like NS9530 is engineered for continuous cuts and small depths of cut, where the focus is on surface finish and edge sharpness rather than heavy metal removal. The sharp edge and the single-sided chipbreaker reduce built-up edge and lower cutting forces, which supports consistent part quality and predictable tool wear. Where process stability and consistent results are required, the insert’s geometry and grade contribute to reduced rework and higher first-pass yield. Compatibility and mounting for swift index changes As an ISO plate, compatibility with the clamping system depends on form, relief angle, tolerance class, mounting, size and thickness. The system typically comprises an ISO turning insert, a matching external holder or boring bar, a locating pad or clamping kit and replacement screws for rapid changeovers. The central hole with a cylindrical bore and one-sided countersink (40°–60°) ensures secure seating and repeatable positioning in standard clamping systems, enabling straightforward indexing and minimal fixture adjustment time. Practical recommendations for productive turning For finishing passes, select a stable holder and minimise overhang to exploit the low cutting forces of the cermet grade; the 11° relief angle and sharp edge favour continuous cuts with small depths of cut. The single-sided chipbreaker and the rhombic plate form are suited to unobstructed chip flow in common steel turning scenarios. Match the chipbreaker and the insert grade to the workpiece stability and machining strategy to achieve the best compromise between surface finish and tool life. If specific cutting parameters are required, consult the technical datasheet to align speeds and feeds with machine capability and part requirements. Contact Metav Werkzeuge today for tailored application advice on Tungaloy cermet inserts and to request complete technical data via info@metav-werkzeuge.com or by phone on +49 2822 7131930 Technical data Article number: 6997918 SKU: 6997918-Tungaloy Manufacturer article number: 6997918 Model series: ISO turning inserts Designation: CPGT080204 Core data Geometry angle: 80° Size: 08 Thickness: 2.38 mm Relief angle: 11° Corner radius: 0.4 mm Special features Uncoated cermet grade NS9530 Rhombic plate form With central hole; cylindrical hole + one-sided countersink (40°–60°) Single-sided chipbreaker For finishing steel; continuous cuts and small depths Compatible holder determined by form, relief angle, tolerance, mounting, size and thickness FAQ What materials is this insert intended for? The insert with grade NS9530 is intended primarily for finishing of steel; the cutting concept is optimised for continuous cuts and small depths of cut. How does the CPGT080204 geometry affect machining? The rhombic 80° geometry gives a versatile cutting edge orientation that supports stable contact and good surface finish during finishing operations with low cutting forces. Is the insert suitable for unstable setups or long overhangs? The CPGT080204 NS9530 insert is designed for situations favouring low cutting forces and sharp edges; for long overhangs or unstable setups, a more robust grade or geometry should be considered to maintain process security. What clamping elements are required for installation? Installation requires a compatible ISO holder or boring bar, locating pad or clamping kit, and the correct replacement screw; the central hole with countersink ensures repeatable seating. Which SKU should be ordered for this insert? Order using SKU 6997918-Tungaloy or Manufacturer article number 6997918 for the CPGT080204 NS9530 Tungaloy turning insert. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
CPGT 080204 TH10 Wendeplatten - Tungaloy
The combination of a sharp, uncoated TH10 grade and a compact 0.4 mm corner radius ensures low cutting forces and clean surface finishes in non‑ferrous turning operations; compatibility with ISO holders guarantees straightforward integration. Order the insert directly via Metav Werkzeuge or consult our specialists for application support. CPGT 080204 TH10 Tungaloy indexable insert (turning) — ISO rhombic, 0.4 mm corner radius A CPGT080204 TH10 indexable insert for ISO‑standard turning, engineered for external and internal turning of non‑ferrous components where low cutting forces and fine surface quality are required ISO rhombic insert, designation CPGT080204 Uncoated carbide TH10 for non‑ferrous materials 0.4 mm corner radius for fine surface finish Single‑sided chipbreaker and 11° clearance Consistent low‑force cutting for non‑ferrous materials The combination of the TH10 cutting grade and uncoated cemented carbide substrate provides a sharp cutting edge that reduces cutting forces and supports clean surfaces when machining aluminium, brass and similar alloys. Lower cutting forces translate into reduced tool deflection and improved dimensional accuracy, which benefits cycle times and repeatability. The modest 0.4 mm corner radius assists in producing a fine finish while limiting burr formation; when used under stable machining conditions, the result is a reliable, reproducible surface quality for precision turning tasks. Secure clamping and ISO compatibility for dependable performance Manufactured to ISO dimensions, the insert fits holders when form, clearance angle, tolerance class, fastening method, size and thickness match. The plate features a cylindrical hole with a one‑sided countersink (40°–60°) for positive clamping and quick indexability. The 11° clearance and 2.38 mm thickness ensure stable seating in compatible toolholders, reducing vibration and enhancing tool life. Specifying the correct seat and fastening hardware minimises setup time and secures consistent cutting conditions across production batches. System approach to increase productivity and process control Use of an ISO indexable insert together with a matched external holder or boring bar, a suitable backing pad/clamping kit and spare screws creates a complete system for turning operations. The single‑sided chipbreaker is designed to manage chips in many non‑ferrous scenarios; selecting the right chipformer and grade for the material and machining stability improves chip evacuation and reduces downtime. This component‑level approach supports higher throughput and predictable results, making the insert a practical choice for workshops seeking efficient, repeatable turning performance. For reliable turning results with Tungaloy quality and practical application advice, contact Metav Werkzeuge for tailored recommendations or to arrange supply of the CPGT080204 TH10 insert — eMail info@metav-werkzeuge.com or call +49 2822 7131930 Technical Data Article number: 6802391 Manufacturer article number: 6802391 Manufacturer SKU: TUN6802391 Seller SKU: 6802391-Tungaloy Model series: ISO-Drehwendeschneidplatten Designation: CPGT080204 TH10 Core specifications Corner radius: 0.4 mm Clearance angle: 11° Thickness: 2.38 mm Insert size: 08 Included angle: 80° Design & features Material: cemented carbide Shape: rhombic Hole: with hole Hole style: cylindrical hole + one‑sided countersink (40°–60°) Chipbreaker: single‑sided Grade: TH10 (uncoated) Typical application: turning (external and internal) FAQ What materials is this insert best suited for? The CPGT080204 TH10 Tungaloy indexable insert is optimised for non‑ferrous materials, offering low cutting forces and clean surface results when machining aluminium, brass and similar alloys. Is the insert coated or uncoated? This insert is an uncoated cemented carbide grade (TH10), chosen where a sharp, low‑friction edge supports reduced cutting forces and improved finishes. Which holder features must match for correct fitment? Compatibility is determined by form, clearance angle, tolerance class, fastening method, size and thickness; the insert requires a seat for an ISO rhombic plate size 08, 2.38 mm thickness and the central hole with countersink as specified. How does the corner radius affect the surface finish? The 0.4 mm corner radius provides a balance between edge strength and fine finishing ability, helping to achieve smoother surfaces without excessive cutting pressure. Can this insert be used for internal turning as well as external? Yes — the ISO design and chipbreaker configuration make the plate suitable for both external and internal turning when paired with the appropriate boring bar or holder. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand‑new product from the manufacturer.
Fragen zu diesen Produkten??
Mit mehr als 30 Jahren Erfahrung beraten wir Sie gerne persönlich.
Tel.: +49 2822 7131930
Mail: info@metav-werkzeuge.com