How do you use a micrometer correctly?

Precision blind‑hole inspection is facilitated by the combination of a self‑centring three‑point head, carbide measuring faces and an accuracy of ±0.005 mm; order the MS908.663 via Metav Werkzeuge or consult our advisors for specification support. MS908.663 — three‑point internal micrometer with self‑centring head and ±0.005 mm accuracy (Metav IndustryLine) A self‑centring three‑point internal micrometer MS908.663 designed for fast, repeatable measurement of blind holes in workshop and production environments. Self‑centring three‑point measuring head Accuracy ±0.005 mm for repeatable results Carbide measuring faces for long service life Delivered in a protective transport case Precise blind‑hole measurement with minimal operator error The three‑point measuring concept produces a natural centre‑finding action that stabilises the instrument inside a blind hole, reducing eccentricity and operator influence. With an analogue reading of 0.005 mm and an accuracy of ±0.005 mm, this gauge is suited to quality‑critical internal diameter checks where small deviations matter. The vernier‑style scale enables direct mechanical reading without reliance on batteries or electronics, supporting uninterrupted inspections on the shop floor. This combination of mechanical reliability and fine resolution promotes consistent pass/fail decisions during incoming inspection and first‑off checks. Built for demanding workshop use and long‑term repeatability Constructed with carbide measuring faces, the instrument resists wear in daily use and preserves measuring integrity over longer service intervals. The instrument’s physical length of 145 mm and measuring span of 100–125 mm places it in the standard measuring range for general machine‑shop applications, offering a practical balance between reach and rigidity. The robust design and hardened contact surfaces make the micrometer tolerant of routine handling; the supplied protective transport case reduces the risk of damage during storage and transit, keeping calibration stability intact. Practical advantages for process control and inspection routines Using a self‑centring, three‑point internal gauge streamlines internal diameter checks in blind holes, bores and recesses, enabling faster set‑ups at the bench or on the machine. The instrument’s repeatable seating and fine resolution help to reduce scrap and rework by catching dimensional drift earlier in the process. As an analogue instrument it integrates easily into established measurement routines and inspection sheets, while its mechanical simplicity minimises downtime compared with devices that rely on electronics. Typical applications and handling guidance The micrometer is intended for blind‑hole and internal diameter measurements in general engineering, toolroom checks and production quality control. For best results, ensure clean contact surfaces and a stable seating in the bore before taking a reading; the three‑point head will centre itself, but careful alignment reduces measurement scatter. Periodic verification against a gauge block or master ring is recommended to confirm ongoing accuracy and to schedule recalibration when necessary. The instrument’s durability and simple operation make it a practical choice for repetitive internal measurements on ferrous and non‑ferrous components. For reliable blind‑hole inspection with Metav IndustryLine precision, contact Metav Werkzeuge for purchase and expert advice by email at info@metav-werkzeuge.com or by telephone on +49 2822 7131930 Technical data Article number: MS908.663 Name: Three‑point internal micrometer Brand: Metav IndustryLine Type: Analogue internal measuring instrument Numbers / Core technical data Measuring range: 100–125 mm Measuring length: 145 mm Reading / Resolution: 0.005 mm Accuracy: ±0.005 mm Special features / Design Self‑centring three‑point measuring head Carbide measuring faces Delivered in a protective transport case Suitable for blind‑hole (blind bore) measurement FAQ How does the three‑point head help with blind‑hole measurement? The three‑point geometry of the MS908.663 automatically centres inside a blind hole, reducing eccentricity and improving repeatability of internal diameter readings. What level of accuracy and resolution can be expected? The instrument provides a resolution of 0.005 mm with an accuracy of ±0.005 mm, making it suitable for tight tolerance internal checks in production and workshop environments. Is the gauge suitable for frequent workshop use? Yes; the carbide measuring faces and robust mechanical construction are designed for daily inspection tasks and extended service life. Can this micrometer measure other internal features besides blind holes? While optimised for blind holes, the instrument can be used for internal diameter checks, recesses and similar internal features where the three‑point contact can seat reliably. What is included with the instrument on delivery? The MS908.663 is supplied complete with a protective transport case to protect the gauge during storage and transport. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com

Take advantage of the combination of precise three-point measurement, wireless data output with USB, and full ISO 17025 calibration for dependable bore inspection and traceable results; order via Metav Werkzeuge or consult the specialists for application advice. Three-point internal micrometer — digital, 100–150 mm measuring range, Wireless + USB, Microtech Metrology The Three-point internal micrometer is a digital, workshop-ready instrument for repeatable bore and internal diameter checks from 100 to 150 mm, designed for production quality control and laboratory verification. ISO 17025 calibration certificate included Wireless and USB data output Colour 1.5" touchscreen display High repeatability: 0.004 mm accuracy Reliable measurement where it matters The instrument delivers consistent three-point measurement across bores, reducing orientation error and improving repeatability compared with single-point probes. With a specified accuracy of ±0.004 mm, the device supports quality control procedures that demand tight tolerances. The standard-sized measuring range classifies the tool for typical workshop and machine‑shop applications, offering a practical balance between reach and rigidity for medium-sized components. Fast data capture and traceability for production Equipped with Wireless and USB data outputs and a Colour 1.5" touchscreen, the device streamlines data acquisition and logging without manual transcription. The high-resolution reading (0.0001 mm) ensures fine increments are visible on the display, while digital output supports integration into measurement software or SPC workflows. This lowers administrative effort and helps maintain a clear audit trail for batch releases. Practical handling that reduces operator influence The included adjustment ring simplifies zeroing and routine checks, and the three-contact measuring head minimises tilting errors during insertion into bores. A measuring depth of 250 mm allows access to deeper cavities while preserving stability. These ergonomic and mechanical details reduce the effect of operator technique on the measurement result, improving reproducibility across shifts. Certified delivery and industrial readiness This micrometer is supplied fully calibrated to ISO 17025 standards and includes a calibration certificate, making it immediately suitable for accredited quality environments. The combination of high accuracy, digital interfacing and certified calibration positions the instrument as a reliable tool for incoming inspection, in‑process checks and final acceptance testing. Contact Metav Werkzeuge for tailored advice and secure a certified Microtech Metrology three-point internal micrometer (SKU 133715010) with ISO 17025 calibration for your measurement process Technical data Article number: 133715010 GTIN: 4061905074295 Manufacturer: Microtech Metrology ECLASS: 21170335 ETIM: EC003590 Facts Measuring range: 100–150 mm Resolution (reading): 0.0001 mm Accuracy: ±0.004 mm Measuring depth: 250 mm Digital display: Colour 1.5" touchscreen Data output: Wireless + USB Calibration: ISO 17025 certificate included Special features Three-point internal measurement Adjustment ring included Digital operation for SPC integration Suitable for workshop and lab use Delivered calibrated for traceability FAQ Is this instrument supplied calibrated? Yes. The Microtech Metrology three-point internal micrometer (SKU 133715010) is delivered fully calibrated to ISO 17025 and includes the corresponding calibration certificate. Which measurement range does the instrument cover? The device covers a measuring range of 100–150 mm, which places it in the standard class for workshop and machine‑shop bore inspection tasks. How are measurement results exported? Measurement data can be exported either wirelessly or via USB, enabling direct transfer into inspection software or SPC systems from the Microtech Metrology instrument. What resolution and accuracy can be expected? The display resolution is 0.0001 mm and the specified accuracy is ±0.004 mm, suitable for stringent dimensional checks in production control. Is the touchscreen suitable for use with gloves? The 1.5" colour touchscreen provides clear readout and simple menus; for glove operation, common shop gloves may limit sensitivity—repeatable results are maintained via the device’s stable mechanical design. Manufacturer / Responsible: Microtech, Nizhneyurkovska str., 45a, 04080 Kyiv, Ukraine, tool@microtech.tools

Take advantage of the combination of self-centring three-point contact, hardened measuring faces and a protective case for reliable, repeatable blind-bore measurement; order directly via Metav Werkzeuge or request advice from our technical consultants. Three-point internal micrometer MS908.664 — self-centring design, 125–150 mm (Metav IndustryLine) The Three-point internal micrometer MS908.664 is a precision instrument for accurate measurement of blind bores and internal diameters in machine shops and inspection benches Self-centring three-point contact Accuracy ±0.005 mm Hardened measuring faces Supplied in protective case Consistent concentric measurement where it matters The instrument’s self-centring three-point contact mechanism converts small radial differences into a single, centred datum, ensuring high repeatability during blind-bore checks. With a mechanical resolution and accuracy of ±0.005 mm, the device supports tight tolerance verification and process control for internal diameters. This level of precision is particularly useful when comparing series parts or validating internal fits, as the three-point geometry minimises eccentricity and reduces operator-induced variation. Robust construction for repetitive workshop use A durable construction and hardened measuring faces protect the contact points from wear and maintain measurement integrity over prolonged use. The analogue, mechanical drive reduces complexity and avoids battery dependence, making the tool suitable for routine quality inspections on the shop floor. The overall length of 145 mm gives the reach required for its measurement range while keeping the instrument compact enough for stable handling during repeated checks. Ideal balance of reach and stiffness for standard applications Classified in the standard range for internal measurement instruments (125–150 mm), this micrometer offers the best compromise between measuring reach and structural rigidity. That balance is critical in metalworking and fixture assembly, where longer tools can introduce deflection and shorter tools lack coverage. The design is optimised for blind bores, providing reliable access and reproducible contact even when full through-access is not available. Delivered protected and ready for transport The instrument is supplied in a protective case to safeguard measuring faces and the mechanism during transport and storage. Built for regular inspection cycles, it integrates easily into workshop tool sets and measurement benches; its analogue readout is simple to interpret and maintain, supporting efficient quality routines without complex electronic calibration procedures. Contact Metav Werkzeuge for tailored advice on the Metav IndustryLine three-point internal micrometer MS908.664 and to arrange procurement or technical specification support; email info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: MS908.664 Manufacturer: Metav IndustryLine Type: Three-point internal micrometer Feature: Self-centring Measuring range: 125–150 mm Length: 145 mm Accuracy: 0.005 mm Reading: 0.005 mm Mechanism: Analogue Delivery: protective case Measuring faces: hardened Suitable for: blind bores Numeric data Measurement range: 125–150 mm Maximum measurement: 150 mm Minimum measurement: 125 mm Accuracy/resolution: 0.005 mm Length: 145 mm SKU: MS908.664 Design and special features Self-centring three-point contact Hardened measuring faces for wear resistance Analogue drive for low maintenance Compact length for stable handling Supplied in protective case for transport Intended for blind-bore measurement FAQ What measurement range does the instrument cover? The instrument covers a measurement range of 125–150 mm, placing it in the standard workshop range suitable for many machine‑building and metalworking applications; refer to MS908.664 for exact limits. What accuracy and resolution are specified? The device offers an accuracy and reading resolution of 0.005 mm, enabling reliable checks against typical tight tolerance requirements. Is the design suitable for blind bores? Yes — the self-centring three-point contact is engineered specifically to measure blind bores with improved concentricity and repeatability. Are the measuring faces wear-resistant? The measuring faces are hardened to resist wear and maintain consistent contact geometry during repetitive inspection tasks. Is a protective case included? The instrument is supplied in a protective case to secure the micrometer during transport and storage. Is the micrometer digital or analogue? This is an analogue instrument with a mechanical drive and a direct, tactile measuring feel appropriate for workshop environments. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com

Take advantage of the combination of precise 0.005 mm reading, a self‑centring three‑point measuring mechanism and interchangeable measuring inserts to ensure reproducible internal measurements of blind bores in the standard workshop range. Order the instrument directly via Metav Werkzeuge or consult the Metav team for application advice. Three‑point internal micrometer MS908.665 — self‑centring, 150–175 mm range (Metav IndustryLine) The three‑point internal micrometer is an analogue internal measuring instrument designed for reliable measurement of blind bores and internal diameters in the workshop and production environment. Self‑centring three‑point design Measurement range 150–175 mm Analogue reading 0.005 mm resolution Hardened measuring faces, interchangeable insert Reliable metrology for internal diameters and blind bores The three‑point design offers consistent contact on the bore surface, enabling reproducible centring even in deep blind holes. With a measurement range of 150–175 mm this instrument fits the standard class of workshop metrology where reach, stiffness and one‑hand operation are required. The analogue scale provides a clear 0.005 mm reading and an equivalent stated accuracy, which supports routine quality checks and rapid go/no‑go decisions on the shop floor. Practical handling and application benefits for production Interchangeable measuring inserts allow adaptation to differing bore geometries without replacing the whole instrument, reducing downtime and consumable cost. The self‑centring mechanism simplifies alignment and lowers operator variability, which increases throughput and decreases rework. Designed for internal measurements including blind bores, the tool is particularly suitable for machine shops, toolrooms and maintenance departments that require straightforward, rugged measuring devices for repeat measurements. Construction and durability tailored to industrial use Hardened measuring faces reduce wear and maintain measurement fidelity over long service periods; the instrument’s analogue mechanics are engineered for robustness rather than electronic sensitivity. The combination of hardened anvils, an interchangeable insert system and solid construction ensures long‑term stability under workshop conditions and predictable measurement behaviour when performing internal diameter checks on components. Contact Metav Werkzeuge in Emmerich for tailored advice on the MS908.665 three‑point internal micrometer and to arrange delivery from stock — info@metav-werkzeuge.com | +49 2822 7131930 Technical Data Article number: MS908.665 Name: Three‑point internal micrometer (Dreipunkt‑Innenmessschraube) Manufacturer: Metav IndustryLine Core technical data Measurement range: 150–175 mm Reading / resolution: 0.005 mm Accuracy: 0.005 mm Length: 145 mm Analogue instrument Special features Self‑centring three‑point design Hardened measuring faces Interchangeable measuring insert Suitable for blind bores Analogue scale, workshop grade FAQ What measuring range does the MS908.665 cover? The MS908.665 three‑point internal micrometer by Metav IndustryLine covers a measurement range of 150–175 mm. How fine is the resolution and what accuracy is stated? The instrument provides an analogue reading with 0.005 mm resolution and a stated accuracy of 0.005 mm for routine workshop control. Is the design suitable for blind hole measurements? Yes, the three‑point geometry and self‑centring action of this micrometer make it particularly suitable for reliable measurements in blind bores. Can the measuring faces be replaced if worn? The MS908.665 features an interchangeable measuring insert system; hardened faces prolong service life and can be renewed through the insert mechanism. For which workshop tasks is this micrometer intended? The instrument is designed for internal diameter checks in machine shops, toolrooms and maintenance operations where robust, repeatable analogue measurement is required. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com

Take advantage of the self-centring three-point system and interchangeable measuring insert for reliable blind-hole measurements; combined with carbide measuring faces and an accuracy of ±0.007 mm, this instrument supports consistent quality control. Order the (three-point internal micrometer MS908.667) directly via (Metav Werkzeuge) or ask our consultants if needed. Three-point internal micrometer MS908.667 — self-centring, interchangeable insert The three-point internal micrometer for precise measurement of blind bores in workshop and inspection environments, designed as a mechanical instrument for repeatable internal diameter checks. Self-centring three-point system Interchangeable measuring insert Carbide measuring faces for wear resistance High precision ±0.007 mm Reliable blind-bore measurement with minimal operator influence The three-point system centres automatically within blind bores, reducing alignment errors and giving a reproducible contact geometry; this produces consistent results when inspecting bores. With a reading resolution of 0.005 mm (vernier) and a stated accuracy of ±0.007 mm, the instrument narrows measurement uncertainty to a level suitable for many workshop and production control tasks. The effect is a measurable reduction in rework and faster go/no-go decisions on turning and drilling operations. Durable contact surfaces and easy servicing save time Hard-wearing carbide measuring faces extend service intervals and maintain measurement integrity under repeated use. The measuring insert is exchangeable, which simplifies maintenance and allows quick replacement of worn contacts without discarding the whole instrument. The mechanical construction is straightforward and low-maintenance compared with electronic systems, making it suitable for environments where robustness and simple servicing are priorities. Size and handling tuned to everyday workshop needs Classified in the standard measuring range (measuring range 200–225 mm), this device offers a practical balance of reach and stiffness for typical machine‑shop components such as housings, sleeves and medium-sized bores. The instrument’s overall length of 145 mm supports good accessibility in confined bores while remaining easy to handle during repeated checks. As an analogue instrument with a vernier readout, it performs reliably where electronic readouts are unnecessary or undesired. Confidence for quality control and process stability Intended for routine inspection and in-process checks, the micrometer’s self-centring action and robust contact faces reduce operator-dependent variation and increase throughput in batch inspection. The interchangeable insert concept supports lifecycle planning: wear parts can be stocked and replaced quickly to maintain traceable measurement performance. The device is suitable for blind-hole measurement tasks and integrates well into manual quality-control workflows where mechanical verifiability is required. Contact Metav Werkzeuge today for ordering details and specification advice on the Metav IndustryLine three-point internal micrometer MS908.667 and its spare measuring inserts Technical Data Article number: MS908.667 Manufacturer: Metav IndustryLine Category: Micrometers (internal micrometer) Facts Measuring range: 200–225 mm Reading / Resolution: 0.005 mm Accuracy: ±0.007 mm Overall length: 145 mm Display: analogue (vernier) Features & Delivery Self-centring three-point system Carbide measuring faces Interchangeable measuring insert Designed for blind bores (blind-hole measurement) Mechanical, analogue instrument FAQ How does the three-point centring reduce measurement error? The self-centring three-point mechanism distributes contact forces evenly; the three-point internal micrometer MS908.667 centres itself in the bore to reduce eccentricity and improve repeatability. Can the measuring faces be replaced when worn? Yes — the instrument is fitted with an exchangeable measuring insert, so worn carbide faces can be renewed without replacing the entire micrometer. Is the reading digital or mechanical? The device uses a mechanical vernier readout with a reading resolution of 0.005 mm, offering a robust, electronics-free solution for workshop environments. For which bore types is this instrument intended? It is designed specifically for blind bores; the three-point configuration ensures reliable contact geometry in such applications. What is the measuring range and typical accuracy? The measuring range is 200–225 mm and the stated accuracy is ±0.007 mm, suitable for standard workshop inspection tasks. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com

Benefit from the combination of self‑centring three‑point contact, 0.005 mm accuracy and carbide measuring faces to secure reproducible blind‑hole measurements; order the MS908.658 directly via Metav Werkzeuge or consult our specialists for application advice. Three‑point internal micrometer MS908.658 — self‑centring, 40–50 mm range (Metav IndustryLine) The Three‑point internal micrometer MS908.658 is a self‑centring, analogue instrument intended for precision measurement of blind holes and internal bores in small to medium components, offering a compact solution for fine mechanical and toolmaking tasks. Self‑centring three‑point measurement High precision: 0.005 mm accuracy Carbide measuring faces for durability Measuring range 40–50 mm for blind holes Reliable accuracy for critical fits and assemblies The MS908.658 delivers a resolution of 0.005 mm with a matching accuracy of 0.005 mm, providing measurable repeatability for tolerance‑sensitive internal features. The finely graduated analogue scale suits production and workshop environments where a tactile, immediate reading is preferred over electronic systems. This level of precision reduces rework and inspection time by supplying a clear, verifiable measurement result that supports quality control routines and efficient process decisions. Compact, micro‑range design that reduces handling error Classified in the micro range (max. 10–100 mm), the instrument’s 40–50 mm span targets finely detailed components such as small housings, inserts and precision sleeves. The self‑centring mechanism with three‑point contact automatically aligns the measuring faces within a bore, lowering sensitivity to off‑axis entry and operator variance. The compact form factor and balanced length make single‑handed operation straightforward, improving throughput where frequent in‑process checks are required. Durable measuring faces for long‑term repeatability Equipped with carbide (hardmetal) measuring faces, the micrometer resists wear and maintains measurement integrity across extended use. Carbide tips provide a hard, stable contact surface that minimises surface damage to workpieces while preserving repeatable reference points. For workshops seeking a robust, low‑maintenance gauge, this construction ensures a consistent lifecycle performance and contributes to lower total cost of ownership over time. Practical handling, calibration and typical applications The instrument is analogue and supplied with a setting ring at 40 mm to simplify zeroing and quick verification before series checks. Its total length of 97 mm facilitates access to compact bores while keeping the device rigid during measurement. Typical applications include blind‑hole inspection in toolmaking, component verification in precision engineering and quick fit checks in assembly processes. For specification matching and integration into inspection routines, Metav’s product consultants can assist with selection and measuring technique recommendations. Choose the Metav IndustryLine MS908.658 for reproducible blind‑hole measurement and contact Metav Werkzeuge in Emmerich for tailored technical advice: info@metav-werkzeuge.com / +49 2822 7131930 Technical data Article number: MS908.658 Type: Three‑point internal micrometer Brand: Metav IndustryLine Measuring range: 40–50 mm Resolution / reading: 0.005 mm Accuracy: 0.005 mm Operation: Analogue Setting ring: 40 Length: 97 mm Facts Measuring range: 40–50 mm Resolution: 0.005 mm Accuracy: ±0.005 mm Length: 97 mm Special features Self‑centring mechanism Three‑point contact for blind‑hole measurement Carbide (hardmetal) measuring faces Suited for fine mechanical and toolmaking applications Analogue scale for immediate readings FAQ What bore sizes can be measured with this instrument? The MS908.658 covers internal dimensions in the 40–50 mm range and is optimised for blind‑hole measurement within that span. How precise is the measurement capability? The instrument offers a resolution of 0.005 mm with an accuracy rated at 0.005 mm, suitable for many tolerance‑sensitive internal checks. Are the measuring faces wear‑resistant? Yes, the MS908.658 is fitted with carbide (hardmetal) measuring faces, which provide superior wear resistance and long‑term repeatability. Is this gauge suitable for production‑line checks? Its compact, analogue design and self‑centring three‑point system make the micrometer well suited to repetitive in‑process inspections and quick verification tasks. Does the micrometer require electronic data output? This model is analogue and does not include electronic data output; it is designed for direct, fast readings on the shop floor. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com

Take advantage of a self‑centring three‑point measuring head and a 0.005 mm accuracy across a compact 50–63 mm range for reproducible blind‑bore inspections; order the instrument directly via Metav Werkzeuge or consult the specialists for application advice. Three‑point internal micrometer MS908.659 — Metav IndustryLine, self‑centring, 50–63 mm The Three‑point internal micrometer is a precision instrument designed for accurate measurement of blind bores and other internal diameters within the 50–63 mm range, combining a self‑centring three‑point head with robust analogue mechanics for repeatable results. Self‑centring three‑point measuring head Range 50–63 mm Accuracy 0.005 mm Carbide measuring faces Reproducible internal measurements through self‑centring design The instrument’s self‑centring three‑point measuring head converts small operator variations into consistent contact across the bore, which reduces eccentricity and minimises measurement scatter. With a declared accuracy of 0.005 mm and an analogue readout, this tool offers a clear, verifiable performance baseline that supports process control and reduces rework in production environments. The three‑point geometry is particularly effective on short to medium blind bores, where central alignment is critical to obtain reliable diameter values. Built for workshop use: durable faces and compact handling Equipped with carbide measuring faces, the device resists wear from regular contact with machined surfaces and maintains form integrity during frequent use. The compact overall length of 114 mm and a setting ring of 62 support comfortable handling in workshop and inspection‑bench situations, enabling efficient measurement cycles without sacrificing stiffness. As an analogue instrument, it delivers straightforward operation and low maintenance while providing the tactile feedback many technicians prefer for repeat measurements. Practical benefits for quality assurance and inspection routines Integrating this internal micrometer into quality checks provides a direct improvement to inspection throughput and measurement consistency. The tool is explicitly suitable for blind‑bore applications and mechanical assembly checks, offering a reliable technical solution where calipers or telescoping gauges may be less repeatable. The combination of a robust three‑point head and carbide contact faces translates into fewer measurement-related interruptions and a steadier conformity assessment across batches. Contact Metav Werkzeuge in Emmerich for tailored advice on application and availability of the MS908.659 three‑point internal micrometer Technical data Article number: MS908.659 Product: Three‑point internal micrometer Manufacturer: Metav IndustryLine Numbers / Core technical data Measuring range: 50–63 mm Minimum range: 50 mm Maximum range: 63 mm Reading / resolution: 0.005 mm Accuracy: 0.005 mm Length: 114 mm Setting ring: 62 Special features / Designs Self‑centring three‑point head Carbide (hard‑metal) measuring faces Analogue mechanical operation Suitable for blind bores FAQ What degree of accuracy can be expected from this three‑point internal micrometer? The MS908.659 from Metav IndustryLine delivers an accuracy of 0.005 mm with a 0.005 mm reading increment, suitable for precise workshop inspection tasks. Is this instrument suitable for blind‑bore measurement only? While optimised for blind bores, the three‑point internal micrometer is also applicable to other internal diameter checks where central alignment and repeatability are required. How does the self‑centring feature improve measurement results? The self‑centring three‑point head ensures even contact around the circumference, reducing eccentricity and enabling more reproducible diameter readings during routine inspections. What maintenance is recommended to retain measurement reliability? Regular cleaning of the carbide faces and periodic verification against a calibrated ring gauge will preserve the instrument’s performance; the analogue mechanics favour simple, on‑site care. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com

Take advantage of a compact, self-centring three-point measuring head and 0.004 mm accuracy to inspect blind bores with confidence; the instrument’s fine graduations and carbide measuring faces ensure repeatable results in precision workshops. Order directly via Metav Werkzeuge or consult our specialists for application advice. Three-point internal micrometer MS908.651 — self-centring three-point head, 8.0–10.0 mm range (Metav IndustryLine) A three-point internal micrometer designed for precise measurement of blind bores in fine mechanical and workshop environments Self-centring three-point head Carbide measuring faces for durability 0.004 mm measurement accuracy 0.001 mm reading increment Precision engineered for blind-bore measurement The compact three-point design centres automatically on the bore, so alignment errors are reduced and repeatability improves for series checks. The instrument combines a finely graduated analogue spindle with a 0.001 mm reading increment and a verified measurement accuracy of 0.004 mm, which supports quality-controlled machining and inspection routines. This level of reproducibility is particularly valuable when measuring short, deep blind bores where radial run-out and offset would otherwise distort results. Durable contact surfaces and compact ergonomics for workshop use Carbide-tipped measuring faces give long service life under frequent contact and resist wear from abrasive contaminants, maintaining measurement integrity over time. The micrometer’s compact form — overall length 54.5 mm — places it in the micro class for instruments intended for extremely compact, fine‑mechanical tasks; the short, stiff geometry helps to keep handling-induced deflection to a minimum and is ideal for toolrooms, gauges and precision workshops where space and access are limited. Simple analogue operation that integrates with quality processes As an analogue instrument with a clear mechanical spindle, the device delivers tactile feedback and fast, direct readings that can speed up routine inspections without reliance on batteries or electronics. The self-centring action and carbide faces reduce setup time and scrap, while the fine reading increment enables informed pass/fail decisions at the bench. For traceable documentation, the micrometer’s technical values support incorporation into existing inspection protocols and measurement logs. Enquire with Metav Werkzeuge for tailored application advice or to procure the Metav IndustryLine three-point internal micrometer MS908.651 for precision blind‑bore inspection Technical data Article number: MS908.651 Type: Three-point internal micrometer Manufacturer: Metav IndustryLine Facts Measurement range: 8.0–10.0 mm Minimum range: 8.0 mm Maximum range: 10.0 mm Accuracy: ±0.004 mm Reading increment: 0.001 mm Length: 54.5 mm Special features Self-centring three-point head Carbide measuring faces Analogue operation Setting ring: 8 Suitable for blind bores FAQ What measurement range does the instrument cover? The MS908.651 covers a range of 8.0–10.0 mm for internal measurements. How precise is the three-point internal micrometer? The instrument provides a measurement accuracy of ±0.004 mm with a reading increment of 0.001 mm. Are the measuring faces wear-resistant? Yes, the measuring faces are carbide tipped to ensure long-term durability and consistent contact behaviour. Is the device suitable for routine workshop checks of blind bores? The three-point centring head and compact geometry make the MS908.651 well suited to routine blind-bore inspections in toolrooms and precision workshops. Metav IndustryLine: Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com