Worauf sollte man beim Kauf einer 3-Punkt-Innenmessschraube achten?

Precision blind‑hole inspection is facilitated by the combination of a self‑centring three‑point head, carbide measuring faces and an accuracy of ±0.005 mm; order the MS908.663 via Metav Werkzeuge or consult our advisors for specification support. MS908.663 — three‑point internal micrometer with self‑centring head and ±0.005 mm accuracy (Metav IndustryLine) A self‑centring three‑point internal micrometer MS908.663 designed for fast, repeatable measurement of blind holes in workshop and production environments. Self‑centring three‑point measuring head Accuracy ±0.005 mm for repeatable results Carbide measuring faces for long service life Delivered in a protective transport case Precise blind‑hole measurement with minimal operator error The three‑point measuring concept produces a natural centre‑finding action that stabilises the instrument inside a blind hole, reducing eccentricity and operator influence. With an analogue reading of 0.005 mm and an accuracy of ±0.005 mm, this gauge is suited to quality‑critical internal diameter checks where small deviations matter. The vernier‑style scale enables direct mechanical reading without reliance on batteries or electronics, supporting uninterrupted inspections on the shop floor. This combination of mechanical reliability and fine resolution promotes consistent pass/fail decisions during incoming inspection and first‑off checks. Built for demanding workshop use and long‑term repeatability Constructed with carbide measuring faces, the instrument resists wear in daily use and preserves measuring integrity over longer service intervals. The instrument’s physical length of 145 mm and measuring span of 100–125 mm places it in the standard measuring range for general machine‑shop applications, offering a practical balance between reach and rigidity. The robust design and hardened contact surfaces make the micrometer tolerant of routine handling; the supplied protective transport case reduces the risk of damage during storage and transit, keeping calibration stability intact. Practical advantages for process control and inspection routines Using a self‑centring, three‑point internal gauge streamlines internal diameter checks in blind holes, bores and recesses, enabling faster set‑ups at the bench or on the machine. The instrument’s repeatable seating and fine resolution help to reduce scrap and rework by catching dimensional drift earlier in the process. As an analogue instrument it integrates easily into established measurement routines and inspection sheets, while its mechanical simplicity minimises downtime compared with devices that rely on electronics. Typical applications and handling guidance The micrometer is intended for blind‑hole and internal diameter measurements in general engineering, toolroom checks and production quality control. For best results, ensure clean contact surfaces and a stable seating in the bore before taking a reading; the three‑point head will centre itself, but careful alignment reduces measurement scatter. Periodic verification against a gauge block or master ring is recommended to confirm ongoing accuracy and to schedule recalibration when necessary. The instrument’s durability and simple operation make it a practical choice for repetitive internal measurements on ferrous and non‑ferrous components. For reliable blind‑hole inspection with Metav IndustryLine precision, contact Metav Werkzeuge for purchase and expert advice by email at info@metav-werkzeuge.com or by telephone on +49 2822 7131930 Technical data Article number: MS908.663 Name: Three‑point internal micrometer Brand: Metav IndustryLine Type: Analogue internal measuring instrument Numbers / Core technical data Measuring range: 100–125 mm Measuring length: 145 mm Reading / Resolution: 0.005 mm Accuracy: ±0.005 mm Special features / Design Self‑centring three‑point measuring head Carbide measuring faces Delivered in a protective transport case Suitable for blind‑hole (blind bore) measurement FAQ How does the three‑point head help with blind‑hole measurement? The three‑point geometry of the MS908.663 automatically centres inside a blind hole, reducing eccentricity and improving repeatability of internal diameter readings. What level of accuracy and resolution can be expected? The instrument provides a resolution of 0.005 mm with an accuracy of ±0.005 mm, making it suitable for tight tolerance internal checks in production and workshop environments. Is the gauge suitable for frequent workshop use? Yes; the carbide measuring faces and robust mechanical construction are designed for daily inspection tasks and extended service life. Can this micrometer measure other internal features besides blind holes? While optimised for blind holes, the instrument can be used for internal diameter checks, recesses and similar internal features where the three‑point contact can seat reliably. What is included with the instrument on delivery? The MS908.663 is supplied complete with a protective transport case to protect the gauge during storage and transport. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com

Take advantage of the combination of precise three-point measurement, wireless data output with USB, and full ISO 17025 calibration for dependable bore inspection and traceable results; order via Metav Werkzeuge or consult the specialists for application advice. Three-point internal micrometer — digital, 100–150 mm measuring range, Wireless + USB, Microtech Metrology The Three-point internal micrometer is a digital, workshop-ready instrument for repeatable bore and internal diameter checks from 100 to 150 mm, designed for production quality control and laboratory verification. ISO 17025 calibration certificate included Wireless and USB data output Colour 1.5" touchscreen display High repeatability: 0.004 mm accuracy Reliable measurement where it matters The instrument delivers consistent three-point measurement across bores, reducing orientation error and improving repeatability compared with single-point probes. With a specified accuracy of ±0.004 mm, the device supports quality control procedures that demand tight tolerances. The standard-sized measuring range classifies the tool for typical workshop and machine‑shop applications, offering a practical balance between reach and rigidity for medium-sized components. Fast data capture and traceability for production Equipped with Wireless and USB data outputs and a Colour 1.5" touchscreen, the device streamlines data acquisition and logging without manual transcription. The high-resolution reading (0.0001 mm) ensures fine increments are visible on the display, while digital output supports integration into measurement software or SPC workflows. This lowers administrative effort and helps maintain a clear audit trail for batch releases. Practical handling that reduces operator influence The included adjustment ring simplifies zeroing and routine checks, and the three-contact measuring head minimises tilting errors during insertion into bores. A measuring depth of 250 mm allows access to deeper cavities while preserving stability. These ergonomic and mechanical details reduce the effect of operator technique on the measurement result, improving reproducibility across shifts. Certified delivery and industrial readiness This micrometer is supplied fully calibrated to ISO 17025 standards and includes a calibration certificate, making it immediately suitable for accredited quality environments. The combination of high accuracy, digital interfacing and certified calibration positions the instrument as a reliable tool for incoming inspection, in‑process checks and final acceptance testing. Contact Metav Werkzeuge for tailored advice and secure a certified Microtech Metrology three-point internal micrometer (SKU 133715010) with ISO 17025 calibration for your measurement process Technical data Article number: 133715010 GTIN: 4061905074295 Manufacturer: Microtech Metrology ECLASS: 21170335 ETIM: EC003590 Facts Measuring range: 100–150 mm Resolution (reading): 0.0001 mm Accuracy: ±0.004 mm Measuring depth: 250 mm Digital display: Colour 1.5" touchscreen Data output: Wireless + USB Calibration: ISO 17025 certificate included Special features Three-point internal measurement Adjustment ring included Digital operation for SPC integration Suitable for workshop and lab use Delivered calibrated for traceability FAQ Is this instrument supplied calibrated? Yes. The Microtech Metrology three-point internal micrometer (SKU 133715010) is delivered fully calibrated to ISO 17025 and includes the corresponding calibration certificate. Which measurement range does the instrument cover? The device covers a measuring range of 100–150 mm, which places it in the standard class for workshop and machine‑shop bore inspection tasks. How are measurement results exported? Measurement data can be exported either wirelessly or via USB, enabling direct transfer into inspection software or SPC systems from the Microtech Metrology instrument. What resolution and accuracy can be expected? The display resolution is 0.0001 mm and the specified accuracy is ±0.004 mm, suitable for stringent dimensional checks in production control. Is the touchscreen suitable for use with gloves? The 1.5" colour touchscreen provides clear readout and simple menus; for glove operation, common shop gloves may limit sensitivity—repeatable results are maintained via the device’s stable mechanical design. Manufacturer / Responsible: Microtech, Nizhneyurkovska str., 45a, 04080 Kyiv, Ukraine, tool@microtech.tools

Take advantage of self‑centring three‑point measuring, compact dimensions and a finely graduated reading for consistent blind‑bore checks; the combination of repeatable centring, carbide measuring faces and analogue robustness supports efficient workshop workflows. Order the Three‑point internal micrometer directly via Metav Werkzeuge or ask our consultants if needed. Three‑point internal micrometer MS908.654 — self‑centring, 16–20 mm range (Metav IndustryLine) The Three‑point internal micrometer MS908.654 is a precision instrument designed for reliable measurement of blind bores in the 16–20 mm band, combining a three‑point contact head with a compact frame for confined spaces Self‑centring three‑point head Measurement range 16–20 mm Carbide measuring faces (HM) Delivered in protective case Precise bore measurement where space is limited The three‑point contact design ensures automatic centring inside a blind bore so that the measuring points engage evenly; this reduces eccentricity and improves repeatability compared with single‑point probes. With a defined measurement range of 16–20 mm the instrument falls into the micro class of calipers, making it especially suitable for fine mechanical tasks and small assemblies where controlled measuring force and stable contact geometry are decisive for consistent results. The compact geometry helps to keep torsion low and supports reproducible checks in confined geometries. Workshop‑grade contact surfaces and durability Hard‑facing on the contact surfaces gives dependable wear resistance: the carbide measuring faces resist abrasion in routine shop use and extend service life under frequent contact with metal workpieces. The micrometer’s analogue construction avoids batteries and electronic vulnerabilities, favouring simple maintenance and immediate readiness. Supplied in a protective case, the instrument is shielded during transport and storage, supporting reliable deployment across different production stations. Readability and measurement certainty The instrument provides a fine reading step alongside a verified accuracy that supports confident decision making. With a display increment of 0.005 mm and an assessed accuracy of ±0.004 mm, the micrometer allows precise comparative measurements and go/no‑go assessments in production and quality control. The three‑point mechanism shortens setup time for successive measurements and reduces correctional effort, which increases throughput without compromising measurement integrity. Applications, classification and practical benefit Classified as a micro‑range internal micrometer, the tool is suited to watchmaking, valve seats, small hydraulic components and other blind‑hole checks where a short, rigid measuring system is required. The self‑centring function removes an additional alignment step, while the robust contact material supports mixed workshop environments. As a compact analogue instrument it combines mechanical simplicity with measurement quality, making it an efficient choice wherever repeatable internal diameters must be verified. For procurement or technical advice on Metav IndustryLine measuring instruments, contact Metav Werkzeuge in Emmerich for personalised guidance and secure delivery from our European warehouse Technical data SKU: MS908.654 Manufacturer: Metav IndustryLine Type: Three‑point internal micrometer Core specifications Measurement range: 16–20 mm Accuracy: ±0.004 mm Reading increment: 0.005 mm Overall length: 80 mm Analogue operation Features and materials Self‑centring three‑point head Carbide measuring faces Suitable for blind‑hole bores Delivered in protective case Compact micro‑range instrument FAQ What measurement range does this instrument cover? The Three‑point internal micrometer MS908.654 covers a range of 16–20 mm, designed for precise checks in small blind bores. How accurate is the micrometer for production checks? The instrument offers an assessed accuracy of ±0.004 mm with a reading increment of 0.005 mm, allowing reliable comparative measurements on small components. Are the contact faces suitable for regular shop use? Yes, the measuring faces are made of carbide, providing increased wear resistance and extended service life in routine workshop conditions with the Three‑point internal micrometer. Is this micrometer suitable for very tight or confined bores? Its compact frame and self‑centring three‑point head make the tool especially suitable for confined blind‑hole applications where stable contact and low torsion are required. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com

Take advantage of the combination of self‑centring, carbide measuring faces and high repeatability for reliable blind‑hole inspection; the compact 20–25 mm range is ideal for fine mechanical and precision engineering tasks. Order the instrument directly via Metav Werkzeuge or request specification advice from our consultants. Three‑point internal micrometer MS908.655 — self‑centring, carbide measuring faces (20–25 mm) by Metav IndustryLine The Three‑point internal micrometer MS908.655 is a self‑centring internal measuring instrument designed for accurate measurement of blind holes in precision engineering and workshop environments, offering an analogue reading with fine resolution for repeatable results Self‑centring three‑point mechanism Carbide measuring faces for wear resistance Measurement accuracy 0.004 mm Compact range 20–25 mm for fine parts Precise blind‑hole measurement with minimal setup The instrument delivers high repeatability through its self‑centring three‑point mechanism, which ensures concentric contact inside blind bores without complex alignment. With a rated accuracy of 0.004 mm and an analogue reading of 0.005 mm, the device is engineered for tasks where micrometre‑level certainty matters; this combination reduces rework and measurement uncertainty in small components. The compact design is especially suited to micro fabrication and precision inspection of housings and bores. Durable contact faces and dependable mechanical operation Carbide contact faces provide excellent wear resistance, maintaining measurement integrity over extended use in workshop conditions. The analogue nonius construction offers tactile feedback preferred in many inspection routines and requires no batteries or electronic interfaces, supporting uninterrupted operation on the shop floor. The included adjustment ring (25) enables straightforward zeroing and fine setting, while the robust build keeps the mechanical play to a minimum for consistent results. Designed for micro‑range quality control and fine parts Classified in the micro range (suitable for 10–100 mm scales), the 20–25 mm span targets small‑format parts such as precision sleeves, bearing bores and microassemblies. Its compact dimensions and precise geometry make it practical for use in bench inspection and in‑process checks where access is restricted. The measuring faces and frame geometry have been selected to balance stiffness and accessibility, ensuring stable measurements even when handling delicate components. Integration into workshop procedures and traceability The analogue three‑point gauge complements digital and traditional inspection tools as part of a consistent metrology chain; repeatable manual results simplify tolerance checks and go/no‑go decisions. Further technical documentation and measurement data are available from Metav Werkzeuge for integration into QA processes and production control. For operators transitioning from standard calipers or bore gauges, the instrument provides a clear step up in concentricity control without introducing complex electronics. For specification advice or to secure the MS908.655 from Metav IndustryLine, contact Metav Werkzeuge for personalised guidance at info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: MS908.655 Manufacturer: Metav IndustryLine Product: Three‑point internal micrometer Numbers / Core technical data Measuring range: 20–25 mm Reading / resolution: 0.005 mm Accuracy: 0.004 mm Length: 90 mm Special features / Materials Self‑centring three‑point mechanism Carbide measuring faces Analogue nonius scale Suitable for blind‑hole measurement FAQ What measuring range does the MS908.655 cover? The MS908.655 covers a measuring range of 20–25 mm, making it suitable for small bores and fine mechanical components. How precise is the instrument for repeatable checks? The three‑point internal micrometer achieves a stated accuracy of 0.004 mm with an analogue reading of 0.005 mm, designed for consistent bench and in‑process inspection. Are the measuring faces wear resistant? Yes, the contact faces are made of carbide, providing enhanced wear resistance and long‑term dimensional stability for routine use. Is the gauge suitable for blind‑hole applications? The instrument is explicitly intended for blind‑hole measurement, featuring a self‑centring mechanism that ensures concentric contact within such bores. Does Metav IndustryLine provide technical support for integration into QA procedures? Metav IndustryLine and Metav Werkzeuge can supply further technical documentation and advice to assist with integration of the MS908.655 into quality control workflows. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com

Take advantage of the combination of precise 0.004 mm accuracy, a self‑centring three‑point measuring head and carbide measuring faces for consistent blind‑hole measurement; order directly via Metav Werkzeuge or contact the consultancy team for tailored advice. MS908.656 Three‑Point Internal Micrometer — Self‑centring, 25–30 mm range (Metav IndustryLine) A three‑point internal micrometer designed for accurate measurement of blind holes and restricted bores in the 25–30 mm range, combining a compact form with stable contact geometry. Three‑point self‑centring measuring head Measuring range 25–30 mm Carbide measuring faces for wear resistance Analogue drive with 0.005 mm resolution Consistent results for blind‑hole inspection The instrument's self‑centring three‑point system guarantees repeatable contact with bore surfaces, reducing setup variance and rework in production inspection. The compact contact geometry suits restricted bores where standard callipers cannot reach, while the analogue drive and fine spindle allow controlled approach to the measuring surfaces. This configuration translates directly into fewer rejected parts and more reliable pass/fail decisions on the shop floor. Precision that meets workshop demands With a documented accuracy of 0.004 mm and a readable resolution of 0.005 mm, the device sits between general workshop tools and high‑precision instruments. The mechanical design and robust spindle ensure stable readings even in routine quality control. For applications that require exact internal diameters in small assemblies, this micrometer provides a balance of sensitivity and practical handling without invoking complex electronic systems. Durable contact surfaces for long service life The measuring faces are made from carbide, offering superior wear resistance under frequent use and abrasive conditions. That hard contact material preserves the reference geometry over many cycles and keeps measurement uncertainty low. An adjustment ring marked 25 assists with quick reference when setting or checking the nominal diameter, making repetitive tasks more efficient and less error‑prone. Compact format for fine mechanical work Classified in the micro range by its 25–30 mm span, the tool is ideal where small, precise components are involved. The short overall length supports handling in confined environments and maintains torsional stiffness for reliable contact pressure. As an analogue internal measuring instrument, it offers familiar operation for technicians while delivering the benefits of a three‑point system designed specifically for blind‑hole measurement. For precise and repeatable blind‑hole measurement, contact Metav Werkzeuge to request the Metav IndustryLine three‑point internal micrometer MS908.656 or to speak with a specialist at info@metav-werkzeuge.com / +49 2822 7131930 Technical Data Article number: MS908.656 Name: Three‑point internal micrometer Manufacturer: Metav IndustryLine Facts Measuring range: 25–30 mm Resolution: 0.005 mm Accuracy: 0.004 mm Length: 90 mm Special features Self‑centring three‑point measuring head Carbide measuring faces Analogue micrometer design Adjustment ring marked 25 Suitable for blind‑hole measurement FAQ What measuring range does this instrument cover? The three‑point internal micrometer MS908.656 covers a measuring range of 25–30 mm, suited to small‑bore and blind‑hole applications. Is this micrometer suitable for blind‑hole measurement? Yes, the self‑centring three‑point system of the Metav IndustryLine three‑point internal micrometer is specifically designed to measure blind holes and restricted bores reliably. What accuracy and resolution can be expected? The instrument provides an accuracy of 0.004 mm with an analogue readable resolution of 0.005 mm, offering precise control for workshop inspections. Are the measuring faces durable for repeated use? The measuring faces are made of carbide, ensuring wear resistance and long‑term stability of the contact geometry under frequent measurement cycles. How is the instrument adjusted for repetitive tasks? An adjustment ring marked 25 is provided for quick reference and repeatable setting when working with the same nominal diameters. Is this a digital instrument? No, the MS908.656 is an analogue internal micrometer, combining mechanical reliability with a fine spindle for controlled readings. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com

Take advantage of the combination of compact, workshop‑grade precision and robust design for repeatable blind‑hole measurement; the self‑centring three‑point contact and hardened measuring faces deliver reliable results across production and maintenance tasks. Order the instrument directly via Metav Werkzeuge or consult our advisors for application guidance. Three‑point internal micrometer MS908.657 (Metav IndustryLine) — Self‑centring, 30–40 mm The Three‑point internal micrometer MS908.657 is a mechanically driven measuring instrument intended for precise internal diameter checks, especially blind‑hole applications in fine mechanical and light industrial environments. Self‑centring three‑point contact system Measurement range 30–40 mm Hardened measuring faces for durability Precision designed for blind‑hole measurement The three‑point geometry provides self‑centring contact inside blind holes, ensuring that the contact points align automatically with the bore axis and thereby reduce eccentricity errors. With an accuracy of ±0.004 mm and a mechanical reading of 0.005 mm, this analogue measuring instrument translates fine thread motion into dependable metrology results without electronic dependence. The three‑point contact method also helps to average minor surface irregularities, which can reduce rework and speed up routine inspection tasks, making it suitable for both small series production and maintenance checks. Compact format for fine mechanical work Classified in the Mikro range (measurement span up to 100 mm), the instrument’s 30–40 mm span and overall length of 97 mm offer a favourable balance between reach and stiffness. This makes the device well suited to precision tasks where space is limited, such as watch and instrument repair, small housings and insert fittings. The hardened measuring faces increase wear resistance and preserve measurement consistency over long service intervals, so that calibration intervals remain predictable and downtime is minimised. Workshop‑ready robustness and simple handling The analogue design emphasises mechanical reliability: a clear adjustment ring (setting ring 40) allows quick pre‑setting and repeatable contact positioning, while the compact construction withstands everyday workshop handling. Delivered in a protective case for transport, the micrometer is prepared for secure storage and movement between benches or sites. The instrument’s straightforward operation and sturdy build lower the barrier to consistent metrology in production, inspection and maintenance workflows while keeping measurement practice transparent and traceable. Contact Metav Werkzeuge today for tailored application advice on the Metav IndustryLine Three‑point internal micrometer MS908.657 and ensure the right fit for blind‑hole inspection in your workshop Technical data Article number: MS908.657 Manufacturer: Metav IndustryLine Product type: Three‑point internal micrometer Suitable for: Blind‑hole measurement Core data Measurement range: 30–40 mm Length: 97 mm Accuracy: ±0.004 mm Reading (resolution): 0.005 mm Adjustment ring: 40 Mechanical type: Analogue Special features Self‑centring three‑point contact Hardened measuring faces Delivered in protective case for transport Suited to fine mechanical and light industrial use FAQ What makes the three‑point contact better for blind holes? The three‑point geometry centres itself in the bore and averages contact positions; the MS908.657 uses this principle to reduce eccentricity and provide stable internal diameter readings for blind‑hole applications. What accuracy and resolution can be expected from this instrument? The instrument offers an accuracy of ±0.004 mm with a mechanical reading of 0.005 mm, giving precise analogue measurement suitable for production checks and workshop inspection. Is the device suitable for watchmaking and small parts? Yes. With its compact dimensions and classification in the Mikro range, the micrometer is well adapted to fine mechanical work, small housings and components where a short, stiff measuring span is required. Are the measuring faces wear‑resistant? The micrometer is supplied with hardened measuring faces, which increases durability and helps maintain measurement consistency over extended use. Does the delivery include a protective case? The instrument is supplied in a protective case for transport and secure storage, making it straightforward to move between benches or sites. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com

Benefit from the combination of self‑centring three‑point contact, 0.005 mm accuracy and carbide measuring faces to secure reproducible blind‑hole measurements; order the MS908.658 directly via Metav Werkzeuge or consult our specialists for application advice. Three‑point internal micrometer MS908.658 — self‑centring, 40–50 mm range (Metav IndustryLine) The Three‑point internal micrometer MS908.658 is a self‑centring, analogue instrument intended for precision measurement of blind holes and internal bores in small to medium components, offering a compact solution for fine mechanical and toolmaking tasks. Self‑centring three‑point measurement High precision: 0.005 mm accuracy Carbide measuring faces for durability Measuring range 40–50 mm for blind holes Reliable accuracy for critical fits and assemblies The MS908.658 delivers a resolution of 0.005 mm with a matching accuracy of 0.005 mm, providing measurable repeatability for tolerance‑sensitive internal features. The finely graduated analogue scale suits production and workshop environments where a tactile, immediate reading is preferred over electronic systems. This level of precision reduces rework and inspection time by supplying a clear, verifiable measurement result that supports quality control routines and efficient process decisions. Compact, micro‑range design that reduces handling error Classified in the micro range (max. 10–100 mm), the instrument’s 40–50 mm span targets finely detailed components such as small housings, inserts and precision sleeves. The self‑centring mechanism with three‑point contact automatically aligns the measuring faces within a bore, lowering sensitivity to off‑axis entry and operator variance. The compact form factor and balanced length make single‑handed operation straightforward, improving throughput where frequent in‑process checks are required. Durable measuring faces for long‑term repeatability Equipped with carbide (hardmetal) measuring faces, the micrometer resists wear and maintains measurement integrity across extended use. Carbide tips provide a hard, stable contact surface that minimises surface damage to workpieces while preserving repeatable reference points. For workshops seeking a robust, low‑maintenance gauge, this construction ensures a consistent lifecycle performance and contributes to lower total cost of ownership over time. Practical handling, calibration and typical applications The instrument is analogue and supplied with a setting ring at 40 mm to simplify zeroing and quick verification before series checks. Its total length of 97 mm facilitates access to compact bores while keeping the device rigid during measurement. Typical applications include blind‑hole inspection in toolmaking, component verification in precision engineering and quick fit checks in assembly processes. For specification matching and integration into inspection routines, Metav’s product consultants can assist with selection and measuring technique recommendations. Choose the Metav IndustryLine MS908.658 for reproducible blind‑hole measurement and contact Metav Werkzeuge in Emmerich for tailored technical advice: info@metav-werkzeuge.com / +49 2822 7131930 Technical data Article number: MS908.658 Type: Three‑point internal micrometer Brand: Metav IndustryLine Measuring range: 40–50 mm Resolution / reading: 0.005 mm Accuracy: 0.005 mm Operation: Analogue Setting ring: 40 Length: 97 mm Facts Measuring range: 40–50 mm Resolution: 0.005 mm Accuracy: ±0.005 mm Length: 97 mm Special features Self‑centring mechanism Three‑point contact for blind‑hole measurement Carbide (hardmetal) measuring faces Suited for fine mechanical and toolmaking applications Analogue scale for immediate readings FAQ What bore sizes can be measured with this instrument? The MS908.658 covers internal dimensions in the 40–50 mm range and is optimised for blind‑hole measurement within that span. How precise is the measurement capability? The instrument offers a resolution of 0.005 mm with an accuracy rated at 0.005 mm, suitable for many tolerance‑sensitive internal checks. Are the measuring faces wear‑resistant? Yes, the MS908.658 is fitted with carbide (hardmetal) measuring faces, which provide superior wear resistance and long‑term repeatability. Is this gauge suitable for production‑line checks? Its compact, analogue design and self‑centring three‑point system make the micrometer well suited to repetitive in‑process inspections and quick verification tasks. Does the micrometer require electronic data output? This model is analogue and does not include electronic data output; it is designed for direct, fast readings on the shop floor. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com

Compact, self‑centring three‑point internal micrometre with a 6.0–8.0 mm measuring range and high mechanical resolution; the MS908.650 combines precise blind‑hole measurement with hardened measuring faces and a fine 0.001 mm reading—Order the three‑point internal micrometre directly via Metav Werkzeuge or ask our consultants if needed Three‑point internal micrometre MS908.650 — self‑centring, 6.0–8.0 mm range Three‑point internal micrometre MS908.650 delivers reliable blind‑hole measurement for precision workshops and production lines Self‑centring three‑point contact Measuring range 6.0–8.0 mm Resolution 0.001 mm reading Hardened measuring faces (HM) Precision where blind‑hole bores matter The self‑centring three‑point contact mechanism ensures coaxial alignment inside blind holes, reducing measurement variability compared with two‑point probes. With a measuring range of 6.0–8.0 mm and an analogue vernier controlled fine adjustment, this instrument is optimised for small‑diameter bores where repeatability is critical. The device’s geometry minimises radial play so that each measurement reflects the actual bore diameter rather than positioning error, which is particularly valuable in small‑component assembly and quality control workflows. Exceptional reading and repeatability for workshop standards Equipped with a mechanical reading division of 0.001 mm, the instrument offers a fine visual resolution while the stated accuracy of ±0.004 mm provides a clear performance expectation for routine inspections. The analogue vernier design gives tactile feedback during measurement, enabling experienced operators to control contact force intuitively. This combination of high resolution and guaranteed accuracy supports process control in machining and metrology tasks where small deviations can affect assembly fit or functional tolerances. Durable contact faces for industrial use The micrometre is fitted with hardened measuring faces (HM) to withstand repeated contact with workpiece surfaces and abrasive contaminants found in production environments. These robust faces preserve the geometry of the contact points over long service intervals, which reduces drift and the need for frequent re‑profiling. In practice, hardened faces extend usable life and maintain measurement integrity when inspecting ferrous and non‑ferrous components during serial production. Designed for blind‑hole measurement and simple handling Specifically configured for blind‑hole bores, the three‑point contact and compact body (length 54.5 mm) permit access to confined features that larger gauges cannot reach. The instrument includes an adjustment ring (setting ring 6) that allows controlled extension of the contact arms, making it suitable for varied hole depths within the stated range. Its compact, mechanically driven construction requires no batteries and integrates easily into inspection benches, making it a practical choice for laboratories and on‑shop measuring stations where robustness and low maintenance are priorities. Contact Metav Werkzeuge today to discuss how the MS908.650 can be integrated into existing inspection routines or to request tailored advice from our technical consultants Technical data Article number: MS908.650 Manufacturer: Metav IndustryLine Type: Three‑point internal micrometre Facts Measuring range: 6.0–8.0 mm Length: 54.5 mm Reading increment: 0.001 mm Accuracy: ±0.004 mm Adjustment ring: 6 Special features Self‑centring three‑point contact Hardened measuring faces (HM) Analogue vernier reading Suitable for blind‑hole bores Category: Messschrauben FAQ What measurement range does this instrument cover? The MS908.650 covers a measuring range of 6.0–8.0 mm, optimised for small blind‑hole bores. Is the device suitable for repetitive production checks? Yes, the MS908.650 is designed for workshop and production use with hardened measuring faces and a robust three‑point contact that supports repeatable inspections. What level of accuracy and resolution can be expected? The instrument provides a reading increment of 0.001 mm and a stated accuracy of ±0.004 mm, suitable for demanding quality control tasks. Can the micrometre measure deep blind holes? The compact length (54.5 mm) and the adjustment ring (6) make the MS908.650 appropriate for many blind‑hole depths within its 6.0–8.0 mm range. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com