Secure and precise workholding for metalworking productivity
Workholding devices such as workpiece clamps and chuck systems provide absolute positional stability and vibration damping during milling, turning, drilling and grinding, ensuring parts remain free of play under high CNC cutting and feed forces. By transferring clamping loads into the machine table or spindle without deforming the component, a well engineered workholding solution improves machining accuracy, surface finish and process reliability while reducing set-up times. Modular systems from machine vices and chucks to zero-point systems and specialised fixtures enable fast changeovers and support both serial and single-part production, delivering consistent clamping force, repeatability and enhanced throughput.
115.5mm Live Centre MK5 Conical Tip 60° Angle, 78mm Body Diameter - RÖHM
Take advantage of a robust MK5 taper and a 115.5 mm overhang to achieve fast, repeatable centring of heavy components while keeping setup times low; order the RÖHM centring cone directly via Metav Werkzeuge or ask the consultants if needed. RÖHM Centring Cone MK5 — 115.5 mm overhang, 60° cone angle The RÖHM Centring Cone MK5 is a precision clamping accessory for aligning heavy workpieces on lathes and machining centres, designed to ensure reliable axial location and stable support during turning operations MK5 taper for standard spindle interfaces 115.5 mm overhang for deep centring tasks 60° pointed cone for precise axial alignment Rated for workpieces up to 1,600 kg Faster setup and consistent axial alignment for machining centres The engineered geometry of the centring tool reduces repositioning and trial cuts, enabling more efficient cycles. With a defined 60° cone angle and a pointed form, the component creates a repeatable contact point that converts radial play into a single, predictable datum. The MK5 taper secures the tool into the spindle with standardised fit, so the combination of MK5 and the 115.5 mm overhang provides a dependable balance between reach and rigidity. This results in measurable time savings on medium and heavy turning tasks while maintaining dimensional control. Robust contact surface for heavy-duty turning and stability Built to take substantial loads, the centring cone supports a maximum workpiece mass of 1,600 kg, which allows its use with large chucks and heavy assemblies. The broad housing with a 78 mm diameter distributes reaction forces and reduces local stress on the spindle nose, improving runout behaviour during contact. Thanks to the pointed cone geometry, axial alignment is achieved with minimal radial offset, improving concentricity and contributing to consistent finishing without repeated adjustments. Reduced rework through defined taper and repeatability The standardised MK5 taper guarantees a tight mechanical interface that resists micro-movement under cutting forces, lowering the likelihood of chatter and surface defects. The precise cone angle and hard seating mean that once the component is located, positional drift is limited; this reliability translates directly into fewer scrapped parts and less rework. For workshop planners, the clear specification of taper, overhang and cone angle simplifies fixture selection and process documentation. Practical considerations: integration, inspection and handling Integration into an existing toolset is straightforward owing to the industry-standard taper and compact housing. Routine inspection focuses on the cone tip and taper seating for wear or burrs; addressing minor damage early maintains the precision of axial location. The simple mechanical design minimises service complexity—when inspections indicate wear beyond allowable tolerance, replacement restores original performance quickly. Packing and transport information note the item is supplied as a single unit for controlled inventory and traceable fitting. For precision centring tasks with demanding loads, choose the RÖHM centring cone MK5 and contact Metav Werkzeuge for ordering and technical advice at info@metav-werkzeuge.com or +49 2822 7131930 Technical data Article number (SKU): 4000832107NW Product type: Centring cone Brand: RÖHM Facts Overhang: 115.5 mm Cone angle: 60° Housing diameter: 78 mm Max. workpiece weight: 1,600 kg Special features Taper design: MK5 Pointed cone form for axial centring Packaging unit: 1 FAQ What spindle interfaces is this centring cone compatible with? The RÖHM centring cone MK5 (SKU 4000832107NW) fits standard MK5 spindles and is intended for machines accepting that taper class. How heavy a workpiece can be centred with this tool? The centring cone is specified for workpieces up to 1,600 kg, offering a stable solution for heavy-duty turning operations. Is the cone geometry suitable for high-precision finishing? Yes, the 60° pointed cone profile provides a consistent axial datum, supporting high repeatability and improved concentricity in finishing passes. What inspections are recommended to maintain centring accuracy? Regular visual and tactile checks of the cone tip and MK5 seating are recommended; any detectable deformation or burrs should prompt repair or replacement to preserve precision. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
116mm Horizontal Clamp Massive Holding Arm, 90° Angle, Zinc Plated - Kukamet
Take advantage of the robust combination of a solid holding arm and a vertical-foot mounting for dependable clamping in repetitive production tasks; the compact 116 mm reach and galvanised finish support long service life and tidy workshop integration. Order through Metav Werkzeuge for fast procurement or request product advice from the Metav team. 112 Horizontal toggle clamp by Kukamet — 116 mm arm, galvanised The 112 is a horizontal toggle clamp designed for secure fixturing on benches and jigs, offering a vertical‑foot mounting for stable installation in industrial and workshop environments. Galvanised steel construction 116 mm solid holding arm Vertical-foot mounting Max holding force 1,200 N Consistent clamping that reduces rework and cycle time The horizontal toggle design delivers a repeatable clamping action that keeps components steady during machining, assembly or inspection. With a holding force of 1,200 N and a pressing force of 1,000 N, the clamp reduces movement and vibration that can cause rejects. The mechanical toggle locks in place, so setups remain consistent across cycles, improving throughput and lowering the likelihood of costly rework. The force values are expressed in newtons to allow easy comparison with other industrial fixtures and to support engineering decisions. Workshop‑grade materials for longevity and low maintenance Constructed from galvanised steel and equipped with a massive holding arm, this clamp is built for daily use in demanding environments. The 116 mm arm length provides practical reach without excessive overhang, while the compact body and a 90° arm orientation keep the footprint small on a jig or bench. Galvanisation protects the metal against corrosion in typical workshop atmospheres, reducing the need for frequent replacement and supporting a stable maintenance schedule. Fast installation and predictable operation for fixture builders The vertical‑foot fastening simplifies alignment on upright plates or bench surfaces and accelerates installation during fixture build‑up. The compact, lightweight construction (approx. 0.228 kg) makes handling straightforward when mounting multiple clamps across a jig. The mechanical behaviour of the toggle mechanism is intuitive for operators and enables quick manual actuation, supporting shorter setup times and more predictable cycle planning in small and medium production runs. Choose the Kukamet 112 for reliable, workshop‑grade clamping and contact Metav Werkzeuge in Emmerich for procurement and technical advice at info@metav-werkzeuge.com or +49 2822 7131930 Product details SKU: 112-2-D-C2 GTIN: 8680731500424 ETIM: EC011973 ECLASS: 21041719 Numbers / Core technical data Arm length: 116 mm Angle: 90° Weight: 0.228 kg Max pressing force: 1,000 N Max holding force: 1,200 N Designs / Special features Material: galvanised steel Mounting: vertical foot Feature: massive holding arm Category: horizontal toggle clamp Asset: 112-D-katalogseite.pdf FAQ What clamping and holding forces does the clamp provide? The Kukamet 112 provides a pressing force of 1,000 N and a holding force of 1,200 N, values given in newtons for straightforward engineering comparison. How is the clamp fastened to a fixture or bench? The clamp uses a vertical‑foot mounting arrangement that allows secure attachment to upright plates or horizontal bench tops, making alignment and installation simpler for modular jigs. What is the reach of the holding arm and how compact is the unit? The holding arm has a reach of 116 mm and the complete unit weighs approximately 0.228 kg, offering a compact solution for multi‑point fixturing. What material is the clamp made from and how does that affect durability? Constructed from galvanised steel with a massive holding arm, the 112 is designed for workshop durability and increased resistance to corrosion in standard industrial atmospheres. Manufacturer: Kukamet Fevzi Çakmak Mah.10644 Sk. No:61-63 42050 Karatay / KONYA TÜRKİYE / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com
117mm Pneumatic Clamp With Solid Holding Arm, 95° Angle, 2 000 N Stroke Force - Kukamet
Benefit from a robust combination of high holding force and durable construction: the heavy-duty galvanised arm delivers dependable clamping at up to 2,500 N, while the compact 117 mm reach keeps fixtures compact and accessible. Order the unit directly via Metav Werkzeuge or consult our specialists for application-specific advice. Kukamet 611 Pneumatic Clamp — 117 mm arm, galvanised A Kukamet 611 pneumatic clamp engineered for horizontal-base mounting to provide secure, repeatable clamping in jigs and production fixtures. *Massive holding arm for robust clamping *117 mm reach for medium assemblies *Galvanised finish for corrosion resistance *Horizontal base for fixed workbench mounting Reliable clamping performance for repetitive production The clamp is built to deliver consistent force: with a rated 2,000 N actuation force and a maximum 2,500 N holding capacity, the device secures components reliably during machining and assembly. The difference between actuation and holding forces is explained by the pneumatic drive mechanism and the mechanical locking of the arm; this combination translates pneumatic input into steady static grip. Such figures make the component suitable for medium-duty industrial applications where repeatability and process security matter most, reducing cycle variation and downtime. Robust construction that stands up to workshop conditions A galvanised finish provides corrosion protection across common workshop environments, extending service life without specialist coatings. The unit features a massive holding arm designed for heavy contact loads and long-term durability; that mass helps resist deformation under repeated stress. These attributes reduce maintenance intervals and support predictable replacement planning, so fixtures remain dimensionally stable and safe over many production cycles. Compact footprint and straightforward integration into fixtures Designed with a horizontal base for fixed mounting, the clamp fits neatly into bench-mounted jigs and modular tooling systems. The 117 mm arm length and the 95° arm angle allow compact layout design while keeping the clamping action accessible to operators and automation end-of-arm tooling. The model's form factor simplifies CAD integration and reduces the need for bespoke adaptors, speeding up fixture assembly and enabling quicker changeovers between part runs. Practical advantages that justify the investment Choosing this pneumatic clamping solution supports operational efficiency: faster workpiece securing means reduced cycle times, and the sturdy construction lowers the likelihood of unplanned stoppages. Metav’s distribution model guarantees consistent availability and quality control from Emmerich, backed by industry experience and a wide product range that simplifies procurement. Together, these factors preserve production throughput and support long-term cost-effectiveness. Contact Metav Werkzeuge for tailored technical advice, availability and ordering options for the Kukamet 611 pneumatic clamp; speak with our Emmerich-based specialists for fast, practical support Technical Data SKU: 611-3-D-C2 GTIN: 8682843521588 ETIM: EC011973 Facts Arm length: 117 mm Angle: 95° Actuation force: 2,000 N Holding force: 2,500 N Special features Material: galvanised Massive holding arm Mounting: horizontal base Type: pneumatic clamp Brand: Kukamet FAQ What mounting arrangement is required for this clamp? The Kukamet 611 pneumatic clamp is supplied for horizontal-base mounting, allowing fixed installation on workbenches and fixtures. What are the clamping and holding forces of the unit? The unit provides an actuation force of 2,000 N and a maximum holding capacity of 2,500 N for reliable workpiece retention. Is the clamp suitable for corrosive or humid environments? The galvanised finish on the Kukamet 611 offers enhanced corrosion resistance, making it suitable for standard workshop and production conditions. What reach does the clamp arm provide for fixture design? The clamp features a 117 mm arm reach, appropriate for medium-sized assemblies and compact jig layouts. Does the design support high-repeatability applications? Yes, the combination of pneumatic actuation and a massive holding arm ensures repeatable clamping performance suitable for series production. Manufacturer: Kukamet Fevzi Çakmak Mah.10644 Sk. No:61-63 42050 Karatay / KONYA TÜRKİYE / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com
117mm Vertical Clamp 2,000N Closing Force, Massive Holding Arm, Galvanised - Kukamet
The combination of a massive holding arm, compact 117 mm reach and up to 2,500 N clamping force ensures secure, repeatable fixation for light-duty fixtures; order the Kukamet vertical clamp directly via Metav Werkzeuge or consult our specialists for specification advice. Vertical clamp 212 — Kukamet (vertical toggle clamp with galvanised finish) A vertical clamp 212 designed for secure bench mounting and repeatable clamping tasks in production jigs, assembly and light machining applications Massive holding arm for stable clamping Vertical base for secure bench mounting Up to 2,500 N clamping force Galvanised finish for corrosion resistance Reliable fixation for repeatable jigs and fixtures The vertical clamp 212 delivers consistent holding power where repeatability matters. With a maximum clamping force of 2,500 N and a specified pressing force of 2,000 N, the device holds workpieces firmly during short-cycle operations and fixture setups. The 117 mm arm provides an extended reach that assists in positioning and clearance, while the lever action simplifies toggle engagement. These measurable values allow planners to include the clamp in process documentation and to design jig geometry around predictable forces. Durable construction that minimises maintenance Constructed with a galvanised finish and featuring a heavy-duty holding arm, the clamp is engineered for long service life in workshop environments. Corrosion resistance from the surface treatment reduces the need for regular refurbishment, while the compact mass of 0.408 kg makes retrofitting into existing jigs straightforward and cost-effective. The robust mechanical design reduces unplanned downtime and supports a higher mean time between replacements, contributing to steady production runs and predictable maintenance planning. Compact mounting and flexible installation for production lines Fitted with a vertical base intended for secure bench mounting, this lever clamp integrates easily into small fixtures and modular tooling. The vertical mounting orientation saves bench space and facilitates stacking of clamps in tight assemblies. The unit’s modest footprint and clear mechanical specification make it suitable for repeated applications in assembly, testing and light machining contexts where reliable clamping and quick engagement are required. For system designers, the compact geometry aids in collision avoidance and repeatable part handling. For tailored advice on integrating the Kukamet vertical clamp 212 into production jigs or to arrange supply via Metav Werkzeuge, please contact Metav Werkzeuge at info@metav-werkzeuge.com or call +49 2822 7131930 for prompt specification support and delivery options. Technical data SKU: 212-3-D-C2 GTIN: 8680731501605 Manufacturer: Kukamet ECLASS: 21041717 ETIM: EC011973 Weight: 0.408 kg Facts Clamping force max: 2,500 N Pressing force max: 2,000 N Arm length: 117 mm Special features Material: Galvanised Mounting: Vertical base Heavy-duty holding arm Category: Clamp FAQ What maximum holding force does the clamp provide? The Kukamet vertical clamp 212 offers a maximum clamping force of 2,500 N and a pressing force of 2,000 N, providing a clear basis for fixture design and load calculation. How is the clamp mounted in a jig or on a bench? Mounting is via a vertical base intended for secure bench installation; the clamp’s compact footprint and vertical orientation ease integration into modular fixtures. Is the surface treatment suitable for workshop environments? Yes, the unit is galvanised, which provides corrosion resistance suitable for standard workshop conditions and reduces maintenance needs. What is the arm reach and how does it affect positioning? The clamp features a 117 mm arm length, offering additional reach for positioning and clearance in assembly jigs while maintaining reliable lever action. Which SKU should be referenced when ordering or specifying this clamp? Reference SKU 212-3-D-C2 (Kukamet vertical clamp 212) when ordering or including the component in technical documentation. Manufacturer: Kukamet Fevzi Çakmak Mah.10644 Sk. No:61-63 42050 Karatay / KONYA TÜRKİYE / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com
117mm Vertical Clamp 2000N Closing Force, Massive Holding Arm & Safety Lock, Zinc Plated - Kukamet
Take advantage of a robust, zinc‑plated design with a 2,000 N clamping force and a massive holding arm with safety lock to secure workpieces reliably; order the clamp directly via Metav Werkzeuge or contact our consultants for application advice. Vertical Toggle Clamp 212 by Kukamet — 2,000 N clamping force, zinc‑plated A robust Vertical Toggle Clamp 212 for secure vertical holding in jigs, fixtures and production tooling. Heavy‑duty holding arm with safety lock 2,000 N clamping force Zinc‑plated corrosion resistance 117 mm lever arm for extended reach Secure clamping that reduces rework and cycle time The clamp delivers a 2,000 N clamping force and a 2,500 N holding force, providing reliable retention during machining, assembly and testing operations. Clamping force refers to the applied pressure that brings a workpiece into position, while holding force describes the resistance to displacement once clamped; the difference ensures stable fixation without overloading the fixture. This combination minimises slippage and reduces the need for repeated adjustments, contributing directly to improved process efficiency and fewer rejects. Built for durability and operator safety Constructed with a zinc‑plated finish, the device resists corrosion in standard workshop conditions, extending service life and lowering replacement cycles. The massive holding arm increases structural stiffness, and the integrated safety locking mechanism prevents accidental release during handling or vibration. These attributes support safer, continuous operation and simplify maintenance schedules, since visible wear points are reduced and routine checks become straightforward. Easy integration into existing fixtures and tooling Designed with a vertical foot mounting, the clamp installs neatly into plates and modular tooling systems, while the 117 mm lever arm gives additional reach where clearance is limited. At roughly 0.37 kg, the unit balances rigidity with minimal added mass, allowing rapid retrofitting without affecting handling or alignment. The compact footprint facilitates dense placement in multi‑station fixtures, helping to streamline setup times and keep cycle layouts compact. Practical choice for light to medium industrial applications This lever‑style vertical clamp is suited to repetitive clamping tasks in jigs, assembly benches and test fixtures where consistent positioning is essential. The combination of corrosion protection, a robust arm and a positive locking feature makes it appropriate for workshop and production environments that prioritise repeatability and uptime. For bespoke fixture designs, the clamp’s straightforward geometry enables predictable behaviour when paired with standard base plates and locating features. Contact Metav Werkzeuge to specify the Kukamet Vertical Toggle Clamp 212 for fixture projects and receive tailored technical guidance and procurement support Technical Data Article number: 212-3-D-L-C2 GTIN: 8680731501636 ECLASS: 21041717 ETIM: EC011973 Facts Clamping force (max): 2,000 N Holding force (max): 2,500 N Lever arm length: 117 mm Weight: 0.37 kg Special features Material: zinc‑plated Mounting: vertical foot Massive holding arm Safety locking mechanism FAQ How much clamping force does the clamp provide? The Vertical Toggle Clamp 212 provides a maximum clamping force of 2,000 N and a holding force of up to 2,500 N for secure fixation. Is the clamp suitable for workshops with varying humidity? The zinc‑plated finish on the 212 gives corrosion resistance suitable for many workshop environments; for aggressive conditions, additional protective measures are advised. How is the clamp mounted in a fixture? The Kukamet Vertical Toggle Clamp 212 is fitted for vertical foot mounting and is intended to be fastened to base plates or fixture subplates. Does the clamp include any safety features? Yes, the clamp is supplied with a safety locking mechanism and a massive holding arm to reduce the risk of unintended release during operation. What are the lever length and weight for integration planning? The unit has a 117 mm lever arm and weighs 0.37 kg; refer to SKU 212-3-D-L-C2 when specifying dimensions for fixture layouts. Manufacturer: Kukamet Fevzi Çakmak Mah.10644 Sk. No:61-63 42050 Karatay / KONYA TÜRKİYE / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com
117mm Vertical Clamp 2000N Closing Force, Massive Holding Arm, Blackened Finish - Kukamet
Robust clamping with a 2,500 N holding force and a 117 mm solid arm delivers secure, repeatable fixtures for production and jig work; the compact weight of 0.413 kg eases integration into existing tooling. Order the Vertikalspanner 211 directly via Metav Werkzeuge or ask our consultants if needed. Vertikalspanner 211 — Vertical toggle clamp with 2,500 N holding force (Kukamet) Vertikalspanner 211 is a vertical toggle clamp engineered for dependable workholding in compact fixtures and production jigs, offering a horizontal foot for stable mounting and a massive holding arm for heavy-duty cycles. Massive holding arm for durability Horizontal foot for stable mounting 117 mm arm length for extended reach 2,500 N holding force for secure clamping Consistent clamping performance that protects cycle time The clamp delivers clear technical advantages for batch production: a maximum pressing force of 2,000 N combined with a maximum holding force of 2,500 N provides differentiated values for actuation and retention. The higher holding force means components remain reliably secured once the toggle is set, while the pressing value describes the force generated during the clamping stroke. This separation of values supports predictable process planning and reduces rework caused by shifting workpieces, improving throughput in repetitive operations. Robust construction for long service life and safe fixtures Built around a massive holding arm, the device is aimed at workshop and industrial environments where mechanical stress is frequent. The solid arm geometry increases resistance to bending and wear, resulting in stable, repeatable clamping over many cycles. The blackened finish protects contact surfaces and gives a professional appearance suitable for visible fixtures. At 0.413 kg, the unit remains compact and easy to position without compromising structural integrity. Compact mounting that fits existing jigs and tooling The horizontal-foot mounting enables direct attachment to flat plates and bench fixtures with a low profile, simplifying integration into existing assemblies. The 117 mm arm length offers an extended reach for clamping over workpieces while keeping the device footprint modest. Installation requires common fasteners and basic alignment; the toggle design ensures quick engagement and secure retention once set, which is particularly useful in modular fixtures and rapid-change tooling setups. Precision and repeatability for reliable production results Designed as a toggle clamp, the device converts lever motion into a firm hold with little variation between cycles, which supports consistent part positioning and repeatable downstream processes such as machining, welding or inspection. The combination of defined mechanical forces, a substantial arm and a stable mounting arrangement reduces the need for frequent readjustment and helps maintain process quality under continuous use. Request a tailored quotation or technical clarification for the Kukamet Vertikalspanner 211 from Metav Werkzeuge — contact info@metav-werkzeuge.com or call +49 2822 7131930 for prompt, local advice and supply from Emmerich. Technical Data Article number: B211-3-D-C2 GTIN: 8680731507706 Manufacturer: Kukamet Facts Arm length: 117 mm Max pressing force: 2,000 N Max holding force: 2,500 N Weight: 0.413 kg ECLASS: 21041717 ETIM: EC011973 Special features Massive holding arm Horizontal foot mounting Blackened finish Toggle / lever clamp design Catalog page PDF available FAQ What is the maximum holding force of this clamp? The Vertikalspanner 211 (Kukamet) provides a maximum holding force of 2,500 N, specified for retention once the clamp is engaged. What does the pressing force value mean? The stated pressing force of 2,000 N refers to the force generated during actuation of the toggle mechanism; it differs from the holding force, which denotes the clamp's retention capability after engagement. How is the clamp mounted in a fixture? Mounting is via a horizontal foot, allowing secure attachment to flat plates or bench fixtures for stable, low-profile installation. What materials and finishes are used? The unit is supplied with a blackened finish, providing a protective surface and a professional appearance suitable for workshop environments. What is the arm reach and how does that affect application? The arm length is 117 mm, offering extended reach for clamping over components while maintaining a compact overall footprint for integration into jigs. Which identifier should be used when ordering spare parts or replacements? Use the Article number / SKU B211-3-D-C2 and the GTIN 8680731507706 for ordering or reference. Manufacturer: Kukamet Fevzi Çakmak Mah.10644 Sk. No:61-63 42050 Karatay / KONYA TÜRKİYE / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com
117mm Vertical Clamp With Massive Holding Arm, 2,000N Thrust / 2,500N Hold - Kukamet
Take advantage of the combination of a massive holding arm, compact 117 mm reach and a 2,500 N holding force for reliable, repeatable clamping in workshop and production environments; order the Kukamet Vertical Clamp 212 directly via Metav Werkzeuge or ask our consultants for suitability advice. Kukamet Vertical Clamp 212 – 117 mm arm, 2,500 N holding force The Vertical Clamp 212 is a robust lever-style clamping device for secure vertical fixation on benches and fixtures, designed to give stable positioning where space is limited. Massive holding arm for extra stability 117 mm reach for versatile clamping 2,500 N holding force for secure fixation Vertical foot for easy mounting on fixtures Secure clamping that fits compact workspaces The vertical clamp combines a massive holding arm with a compact footprint to deliver secure fixation without occupying excessive bench space. At just 0.408 kg, the device is lightweight for its class yet engineered to provide stable support during repetitive operations. The compact design suits jigs, assembly stations and small fixtures where reliable, repeatable clamping increases process throughput and reduces setup time. Precise force control for dependable fixation Designed with clear force ratings, the clamp offers an actuating force up to 2,000 N and a holding force up to 2,500 N, giving a predictable margin between applied and retained force. This distinction supports process planners in selecting the correct clamping solution for delicate assemblies or more rigid workpieces. The combination of defined force values and lever mechanics provides an efficient trade-off between operator effort and secure retention. Simple integration and industrial-grade detailing Mounting is straightforward via the vertical foot, enabling direct attachment to fixtures or bench plates. The lever-style concept (hebelspanner) allows rapid engagement and release, supporting quick cycle times on production lines. The component’s blackened finish gives a uniform appearance and matches typical industrial tooling aesthetics, while the overall construction focuses on durability and functional reliability in everyday workshop use. For direct procurement or to confirm whether the Kukamet Vertical Clamp 212 meets specific application requirements, contact Metav Werkzeuge in Emmerich — phone +49 2822 7131930 or email info@metav-werkzeuge.com — and secure supply from our local stock. Technical data Article number: B212-3-D-C2 GTIN: 8682843522301 Brand: Kukamet Core technical data Weight: 0.408 kg Arm length: 117 mm Holding force max: 2,500 N Actuating force max: 2,000 N Special features Massive holding arm Vertical foot mounting Material/finish: blackened finish Lever clamp design FAQ What applications is this clamp suitable for? The Kukamet Vertical Clamp 212 (SKU B212-3-D-C2) is intended for workshop and fixture applications where vertical clamping and fast engagement are required; its holding force and lever operation suit general production and assembly tasks. What is the effective reach of the clamping arm? The clamping arm provides a reach of 117 mm, enabling access to components in confined or tightly arranged setups. How much force does the clamp deliver and what does that mean in practice? The clamp offers an actuating force up to 2,000 N and a holding force up to 2,500 N, which ensures a clear safety margin between applied input and retained fixation during handling or machining operations. How is the clamp mounted? Mounting is by a vertical foot, designed for direct attachment to benches, plates or fixture bases to provide a stable, low-profile installation. What surface finish does the clamp have? This model features a blackened finish (Schwarz brüniert) that provides a consistent industrial appearance for toolrooms and production lines. Manufacturer: Kukamet Fevzi Çakmak Mah.10644 Sk. No:61-63 42050 Karatay / KONYA TÜRKİYE / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com
117mm Vertical Clamp With Massive Holding Arm, 2,500N Hold Force, Galvanised - Kukamet
Take advantage of the combination of a solid holding arm, a galvanised corrosion-resistant finish and compact weight for dependable clamping in production jigs; order the Kukamet 211 directly via Metav Werkzeuge or consult our specialists for application advice. Kukamet Vertical Toggle Clamp 211 — compact clamping with a solid holding arm and horizontal base The 211 vertical toggle clamp is a compact, robust toggle clamp designed for secure fixturing where a horizontal base and repeatable clamping action are required. Horizontal base for secure mounting Solid holding arm for high stability Galvanised corrosion-resistant finish Max clamping force 2,500 N Reliable clamping that fits tight workflows The 211 delivers a combination of compact dimensions and measurable performance: max clamping force 2,500 N and max pressing force 2,000 N in a package weighing 0.413 kg. The 117 mm reach of the arm allows secure engagement without excessive overhang, while the galvanised finish protects the mechanism against corrosion in standard workshop environments. These measurable values make planning straightforward: fixture loads and actuator requirements can be calculated from the published forces, reducing guesswork during design and assembly. The robust construction supports continuous use in production jigs and small-series manufacturing. Designed for repeatable fixtures and fast throughput A vertical toggle clamp converts lever movement into a secure holding action, offering fast single-handed operation and positive locking under load. The horizontal base simplifies mounting to plates and tooling blocks, enabling consistent positioning across repeat setups. The solid holding arm minimises deflection, which improves part repeatability and reduces rework. As a toggle-style device, the clamp locks mechanically in the closed position, so it resists vibration and maintains contact force without ongoing adjustment. This makes it suitable for assembly, inspection and light machining fixtures where consistent clamping improves cycle times and quality. Low-maintenance durability and integration in production Built from galvanised components, the clamp requires minimal upkeep and resists surface corrosion, which extends service life in typical workshop conditions. The compact mass and simple mounting mean retrofitting into existing tooling is straightforward; standard fastening practices are sufficient for secure installation. For procurement and quality assurance, Metav’s position as a European supply base functions as a practical filter: parts supplied through Metav Werkzeuge are checked for consistency and accessibility across the European market. The clamp’s clear specifications support predictable stocking, while its mechanical simplicity reduces long-term maintenance costs compared with more complex clamping systems. Contact Metav Werkzeuge for tailored application advice and specify the Kukamet 211 vertical toggle clamp to secure fixtures with its solid holding arm and up to 2,500 N holding force Technical data SKU: 211-3-D-C2 GTIN: 8680731501230 Manufacturer: Kukamet Category: Clamp eClass: 21041717 ETIM: EC011973 Facts Arm length: 117 mm Max holding force: 2,500 N Max pressing force: 2,000 N Weight: 0.413 kg Special features Material: galvanised Mounting: horizontal base Massive holding arm Toggle clamp design FAQ What maximum clamping force does the clamp deliver? The clamp provides a maximum holding force of 2,500 N; this value is the primary reference for fixture design when using the Kukamet 211. How is the clamp mounted to tooling plates? Mounting is via a horizontal base, allowing straightforward fastening to plates or tooling blocks for repeatable positioning with the Kukamet 211. Is the finish suitable for humid workshop conditions? Yes, the galvanised finish offers corrosion resistance appropriate for standard workshop environments and reduces the need for intensive maintenance. Can the clamp be used for welding fixtures and assemblies? The toggle design locks mechanically and resists vibration, making the clamp suitable for welding fixtures and assembly operations that require stable part retention. What is the reach of the holding arm? The arm reach is 117 mm, which is useful for determining engagement depth and ensuring the clamp interfaces correctly with the workpiece. Manufacturer: Kukamet Fevzi Çakmak Mah.10644 Sk. No:61-63 42050 Karatay / KONYA TÜRKİYE / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com
118mm Horizontal Clamp With Massive Holding Arm, 90° Pivot, 2.3kN Press Force, 2.5kN Holding Force, Blackened - Kukamet
Take advantage of the robust heavy-duty holding arm, 2,300 N clamping force and compact footprint to secure jigs and fixtures reliably; order the clamp directly via Metav Werkzeuge or ask our consultants if needed. Horizontal lever clamp 111 by Kukamet — heavy-duty horizontal clamp with 2,300 N clamping force The Horizontal lever clamp 111 is a lever-operated horizontal clamp designed for stable workpiece securing in fixtures and jigs, featuring a horizontal foot mount and a massive holding arm for repeatable right-angle clamping. Robust heavy-duty holding arm Horizontal foot mounting for stability 2,300 N maximum clamping force Compact 118 mm arm length Secure heavy-duty clamping at a defined 90° angle The clamp delivers a defined 90° clamping angle, combining a lever mechanism with a massive holding arm to produce consistent, reproducible results on repeated cycles. With a maximum clamping force of 2,300 N and a maximum holding force listed at 2,500 N, this device provides the force levels commonly required for metalworking fixtures and light assembly processes. The lever operation reduces set-up time and ensures an unmistakable locked position, which is especially useful where process stability and operator repeatability matter most. Low-profile mounting for compact fixtures and jigs Thanks to the horizontal foot mounting and a compact 118 mm arm, the clamp integrates easily into tight fixtures and multi-clamp setups. The low profile helps to keep adjacent tooling accessible while the relatively low mass (0.328 kg) minimises added load on movable subassemblies. These dimensional characteristics are advantageous for toolroom fixtures, production jigs and CNC workholding where space optimisation and ease of integration contribute directly to efficient part throughput. Workshop-ready finish and robust construction The component is finished in a blackened surface treatment that resists everyday workshop wear and reduces visible abrasion on frequently handled parts. The solid holding arm construction resists bending under cyclical load, increasing service life and lowering the risk of unexpected downtime. For applications requiring repeated engagement and release, the combination of solid mechanics and a protective finish ensures long-term reliability even in demanding industrial environments. Designed for repeatable setup and fast cycle times Lever-actuated clamps of this design are valued for quick manual actuation and obvious visual confirmation of the locked state, supporting faster cycle times during small-batch production or assembly operations. The clamp’s geometry and force ratings are suited to securing workpieces for machining, inspection or assembly at a fixed right angle, delivering a balance of simplicity and performance that reduces adjustment time and improves overall process consistency. For specification questions or fixture design advice, Metav Werkzeuge can provide targeted recommendations. Contact Metav Werkzeuge for fixture integration guidance and to source the Kukamet Horizontal lever clamp 111 directly for robust, repeatable clamping solutions. Technical data Article number: B111-3-D-C2 GTIN: 8680731507003 Manufacturer: Kukamet Facts Arm length: 118 mm Clamping force max: 2,300 N Holding force max: 2,500 N Angle: 90° Weight: 0.328 kg Special features Horizontal foot mounting Massive holding arm Blackened finish Lever-operated horizontal clamp FAQ What clamping force can be expected from this clamp? The Kukamet Horizontal lever clamp 111 provides a maximum clamping force of 2,300 N, with a maximum holding force specified at 2,500 N, suitable for many light- to medium-duty fixture applications. How is the clamp mounted to a fixture? Mounting is via a horizontal foot, allowing secure attachment to flat fixture plates or tooling blocks for stable right-angle clamping. Is the clamp suitable for integration in compact jigs? Yes, the compact 118 mm arm length and low profile make the clamp well suited for tight fixture layouts and multi-clamp arrangements. What finish does the clamp have for workshop durability? The device features a blackened finish, offering surface protection against wear and a workshop-appropriate, low-reflective appearance. Can this clamp be used for repeated cycle production? The solid construction and lever actuation are designed for repeatable engagement and release, making it appropriate for production jigs and repetitive assembly tasks. Manufacturer: Kukamet Fevzi Çakmak Mah.10644 Sk. No:61-63 42050 Karatay / KONYA TÜRKİYE / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com
119mm Centre Point Slim Extended Pilot Tip 60° MK5 With 51.5mm Tip Length, Max 1400kg Workpiece; Ø58mm Housing - RÖHM
Take advantage of precise runout of 0.01 mm, a 1,400 kg load rating and the MK5 taper for consistent, heavy-duty supported turning; order the RÖHM live centre directly via Metav Werkzeuge or consult our specialists for application advice. RÖHM Live Centre Slim MK5 with Extended Pilot — 60° Tip, MK5 Taper The RÖHM Live Centre Slim MK5 with extended pilot is a lathe centre engineered for precision, supporting heavy workpieces while maintaining low runout and allowing access in confined fixtures. Slim design for restricted access Supports up to 1,400 kg axial load Runout max. 0.01 mm for precision Max. 4,300 rpm for high-speed turning Achieve consistent concentricity in critical turning High-precision applications demand reproducible positioning and minimal deviation. The slim centre delivers a runout of 0.01 mm, which reduces rework and measurement scatter in turned parts. The 60° tip angle and defined tip length ensure stable contact and repeatable alignment during through-centre support, translating technical accuracy into fewer setup iterations and higher first-pass yield. Secure heavy components without compromise For heavy-duty support, the combination of robust construction and rated capacity matters. The unit is specified for a maximum workpiece weight of 1,400 kg, providing the structural basis for supporting large shafts and rings during finishing or rough-turning operations. The centre’s bearing and housing dimensions contribute to load distribution, so machining cycles remain stable and tool life is preserved. Maintain access in restricted bores and fixtures A slim profile with an extended pilot length of 51.5 mm enables engagement in deeper centres and narrow workpiece geometries where standard centres cannot reach. The compact housing diameter of 58 mm and projection of 119 mm minimise interference with tooling and allow closer approach of cutting tools, improving chip evacuation and enabling more flexible clamping strategies on compact lathes. Integrate with common machine tapers and speeds The live centre fits an MK5 shank and presents a shank diameter of 44.399 mm, facilitating direct compatibility with standard taper adaptors and collet fixtures. Rated for up to 4,300 rpm, it supports a broad range of turning speeds from coarse to finish operations while its overall weight of 2.6 kg keeps inertia low for responsive dynamic behaviour. These attributes simplify retrofitting into existing shops and reduce the need for special adaptions. Discuss MK5 compatibility or application-specific requirements with Metav Werkzeuge — our consultants at Metav Werkzeuge can advise on mounting options and delivery from Emmerich, phone +49 2822 7131930 or email info@metav-werkzeuge.com Technical data Article number: 4000832087NW Brand: RÖHM Product type: Live centre (Zentrierspitze) Type designation: Slim - extended pilot Packaging unit: 1 Facts Projection: 119 mm Tip diameter: 30 mm Tip angle: 60° Tip length: 51.5 mm Max. workpiece weight: 1,400 kg Max. runout: 0.01 mm Max. speed: 4,300 rpm Housing diameter: 58 mm Shank diameter: 44.399 mm Weight: 2.6 kg Special features Shank execution: MK5 Slim design with extended pilot Intended for supported turning of heavy workpieces Label: Zentrierspitze Slim MK5 mitlfd.m.verl.Laufspitze RÖHM FAQ What level of concentricity can be expected with this live centre? The RÖHM live centre Slim MK5 delivers a runout specification of 0.01 mm, which supports high-precision turning and repeatable part quality when the centre is used under the stated conditions. Is the slim pilot suitable for deep-diameter workpieces? Yes, the extended pilot length of 51.5 mm is designed to reach deeper centres and provide stable support in narrow bore geometries while maintaining alignment. Which machine taper is required for mounting this centre? The unit is supplied with an MK5 shank execution and a shank diameter of 44.399 mm, allowing direct insertion into compatible MK5 spindles or adaptors. What is the maximum rotational speed for reliable operation? The live centre is rated for up to 4,300 rpm; operating within this limit ensures bearing life and positional stability. Can this centre support very heavy workpieces? The design specification lists a maximum supported workpiece weight of 1,400 kg, making it suitable for substantial components when used with appropriate machine support. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
11mm 5C Collet, 0.02mm Accuracy, 87mm Length - Vertex
Take advantage of the combination of precise clamping, proven 5C compatibility and reliable repeatability for steady production results. Order the collet directly via Metav Werkzeuge or consult the team for application guidance. 5C Collet 11 mm (SKU 5C-11) — High-precision 5C workholding by Vertex The 5C Collet 11 mm is a precision workholding collet for machining applications, engineered to secure round tools and blanks with high repeatability and low runout. 11 mm clamping diameter 0.02 mm runout accuracy Compatible with 5C system chucks 87 mm overall length Consistent precision that improves finish quality Designed for accurate gripping, this workholding sleeve delivers 0.02 mm runout accuracy, which reduces vibration and improves surface finish on turned or milled components. The precise clamping action leads to repeatable concentricity, cutting down setup time and minimising scrap rates. By stabilising the tool or workpiece, the collet helps to extend tool life and supports predictable cycle times in batch production. Flexible integration with established 5C systems As a member of the 5C family, the collet fits standard 5C chucks and fixtures, offering straightforward interchangeability across lathes and milling setups. The 11 mm internal diameter accommodates common round shanks, while the 87 mm overall length allows for deeper engagement where required. This compatibility reduces the need for bespoke adapters and enables rapid changeovers between jobs, supporting lean workflow practices. Robust repeatability for workshop and small-scale production Manufactured to deliver dependable performance across repeated cycles, the component offers measurable stability for production environments seeking consistent results. The modest mass and compact dimensions contribute to easier handling and quicker tooling changes without compromising clamping force. Proven repeatability and mechanical simplicity make this collet a practical choice for workshops that prioritise uptime and quality assurance. For precision clamping solutions from Vertex, contact Metav Werkzeuge in Emmerich for tailored advice and reliable supply — email info@metav-werkzeuge.com or call +49 2822 7131930 Technical Data Article number: 5C-11 GTIN: 4061905088643 ECLASS: 21041712 Facts Clamping diameter: 11 mm Overall length: 87 mm Runout accuracy: 0.02 mm Weight: 0.21 kg Special features 5C collet type Compatible with standard 5C chucks Brand: Vertex FAQ What size shank does this collet accept? The collet accepts an 11 mm shank; the 5C Collet 11 mm (SKU 5C-11) is specified for this diameter. How accurate is the clamping concentricity? Concentricity is specified at 0.02 mm, ensuring low runout for improved surface finish and tool life when using the Vertex collet. Is this collet compatible with standard 5C chucks? Yes, the product is a 5C type collet and fits standard 5C chucks and adapters used in lathes and milling machines. What is the overall length and how does that affect use? The overall length is 87 mm, which allows for deeper engagement in applications that require additional grip length. Who manufactures this collet? The collet is manufactured by Vertex and supplied under SKU 5C-11, reflecting Vertex’s workholding range. Manufacturer: Vertex Machinery Works Co., Ltd.; No. 296, Sec. 1, Feng Shih Road, Fengyuan District, Taichung City 420, Taiwan
11mm ER 16-GB Collet With 9mm Internal Square For Thread Cutting, 15 µm Runout - TECWERK
High concentricity and an integrated internal square ensure reliable thread‑cutting and consistent tool life, while a compact 34 mm length and 11 mm clamping bore guarantee compatibility with standard ER collet chucks; order the collet directly via Metav Werkzeuge or request advice from our technical consultants. ER25-GB collet — 11 mm clamping diameter, 9 mm internal square (TECWERK) The ER25-GB collet is a DIN 6499‑compatible clamping sleeve with an internal square for secure thread cutting, designed for use in ER collet chucks to deliver repeatable concentricity and reliable tool holding. DIN 6499 compatible ER‑GB design Internal square 9 mm for thread cutting Clamping diameter 11 mm Runout accuracy 15 µm for precision Consistent concentricity for repeatable production High concentricity is central to precision machining. The clamping sleeve delivers runout accuracy 15 µm, which reduces wobble and vibration during rotation; this leads to improved surface finish, lower scrap rates and longer tool life. For workshops and small production runs, this level of concentricity means fewer set‑up checks and more predictable process windows. The result is measurable process stability and less unexpected downtime. Secure threading and torque transfer for tapping operations An internal square 9 mm provides a positive drive when thread cutting or tapping, avoiding slippage that can damage tools and workpieces. The design follows DIN 6499, ensuring the collet mates correctly with ER‑style chucks and tap holders. Because the square is integrated rather than an adapter, torque transfer is direct and efficient, which is especially beneficial when working with materials that demand consistent thread form or when using shorter tapping cycles. Compact dimensions that simplify tool management With a compact profile (L 34 mm) and an 11 mm clamping diameter, the sleeve is sized for common ER25 toolholding systems, allowing straightforward replacement without altering existing setups. The modest overall length helps maintain clearance in fixtures and reduces the need for length offsets in CNC programmes. As a standardised clamping component, the collet supports rapid changeovers and reduces the variety of spares required in a workshop environment. For reliable thread‑cutting and precise clamping, contact Metav Werkzeuge to specify the TECWERK ER25-GB collet and request application guidance from our technical team via info@metav-werkzeuge.com or by phone on +49 2822 7131930 Technical data Article number: 2000834967NW Brand: TECWERK Product type: Collet GB Facts Clamping diameter: 11 mm Internal square: 9 mm Length: 34 mm Runout accuracy: 15 µm Special features DIN 6499 compatible ER‑GB design Internal square for thread cutting Suitable for ER collet chucks Packaging unit: 1 FAQ What materials is the ER25-GB collet suitable for? The ER25-GB collet (TECWERK, Article No. 2000834967NW) is designed as a general‑purpose clamping sleeve for ER tooling systems; material suitability depends on the cutting tool and machining parameters rather than the collet itself. How does the internal square help with thread cutting? The internal square 9 mm transfers torque directly from the holder to the tap, reducing slippage; the ER25-GB collet therefore supports reliable thread formation under typical tapping loads. What level of concentricity can be expected in production? The collet achieves a runout accuracy of 15 µm, which supports consistent concentricity for many precision turning and drilling operations and helps to reduce rework. Is the collet compatible with standard ER chucks? Yes — the component follows DIN 6499 dimensions for ER‑GB design, ensuring fitment in standard ER collet chucks and simplifying integration into existing toolholding systems. Manufacturer / Responsible: NORDWEST Handel AG, Robert‑Schuman‑Straße 17, 44263 Dortmund
11mm ER 25-GB Collet With 9mm Internal Square For Thread Cutting, 15 µm Runout - TECWERK
Benefit from precise runout control and integrated tapping capability: the collet’s 15 µm runout accuracy, internal 9 mm square for thread cutting and an 11 mm clamping diameter ensure consistent process quality and reduced rework; order or request advice via Metav Werkzeuge for quick delivery and technical clarification. TECWERK ER-GB Collet – 11 mm clamping diameter, 9 mm internal square A TECWERK ER-GB collet for ER-type collet chucks, designed to support thread cutting with its internal square and to provide high concentricity in light- to medium-duty production environments. Compliant with DIN 6499 Internal square for tapping Runout accuracy 15 µm L 40 mm, clamping d 11 mm Accuracy that safeguards thread quality The primary advantage of this clamping sleeve is its runout accuracy, specified at 15 µm, which noticeably reduces concentricity-related defects during threading and light milling. Compliance with DIN 6499 confirms the geometric tolerances that are expected in professional production and workshop contexts, so the component seated in the chuck stays centred. Fewer rejects and less rework follow from stable clamping concentricity, improving overall process reliability without complex setup changes. Secure clamping and clear dimensional data Built with an 11 mm clamping diameter, an internal 9 mm square for tapping spindles and a nominal length of 40 mm, this collet fits standard ER-type systems and supports thread cutting operations directly from the chuck. The internal square converts the clamping sleeve into a short tapping aid, eliminating an extra tool change for many tapping tasks. Clear dimensional conformity simplifies tool selection and integration into existing collet chucks, enhancing machine uptime and throughput. Practical benefits for the workshop and small production Integration of a GB-style collet into an ER collet system streamlines workflows: fewer tool changes, consistent clamping, and proven compatibility with ER chucks. The mechanical design focuses on stable grip for short-run production and service jobs where accurate threads are required. Combined with Metav’s logistics and technical support, procurement and replacement are straightforward, supporting continuous operation and dependable results on the shop floor. Contact Metav Werkzeuge in Emmerich for procurement or technical guidance on integrating this TECWERK ER-GB collet into existing toolholding systems Technical Data Article number: 2000834975NW Manufacturer: TECWERK Product type: Collet GB Product designation: ER-GB collet Facts Clamping diameter: 11 mm Runout accuracy: 15 µm Length: 40 mm Internal square: 9 mm Packaging unit: 1 Special features DIN 6499 compliant Internal square for tapping / thread cutting Suitable for ER-type collet chucks Designed for secure clamping and concentricity FAQ What materials and operations is this collet intended for? The TECWERK ER-GB collet is specified for general-purpose clamping and is particularly intended to support thread cutting via its built-in 9 mm internal square, as described in the product data. Is the runout specification critical for precision threads? Yes; the stated 15 µm runout accuracy of the collet significantly improves concentricity during threading, reducing the risk of misaligned threads and rework. Will this collet fit existing ER-type chucks? The sleeve is designed for ER-type collet chucks and follows DIN-guided dimensions, so it integrates with standard ER holders used in workshops and small production machines. How does the internal square benefit tapping operations? The internal square permits a direct drive for tapping tools or adaptors, reducing tool changes and simplifying the setup for thread cutting tasks in short to medium production runs. Can this collet be used as a universal replacement for worn collets? The collet can replace worn GB-style ER collets where the dimensional match is identical; check the 11 mm clamping diameter and 40 mm length against existing tooling before installation. Manufacturer / Responsible: NORDWEST Handel AG, Robert-Schuman-Straße 17, 44263 Dortmund
11mm ER25 Collet Precision Clamping, 5 µm Runout, L34 D26 - TECWERK
Take advantage of precise DIN‑compliant clamping, a compact 11 mm clamping diameter and low runout for consistent tool performance; order the collet directly via Metav Werkzeuge or consult the team for integration advice. Collet ER 25/430 E – ER 25 collet, clamping Ø 11 mm (TECWERK) The Collet ER 25/430 E is a high-precision ER 25 collet designed for secure tool holding in ER collet chucks across general machining applications. DIN 6499-B compatibility 11 mm clamping diameter 5 µm runout repeatability Full-length tool clamping Precise compatibility that reduces setup time Engineered to the DIN 6499-B standard, this ER 25 collet ensures consistent fitment in standard ER 25 collet chucks and removes uncertainty when matching tools to chucks. The standardised design and compatibility mean fewer adaptor parts and less inventory overhead, which translates into faster changeovers and lower administrative effort for purchasing. The specification for 5 µm runout underscores the collet’s contribution to precise machining results, supporting longer tool life and more uniform surface finish without requiring specialist fixtures. Compact dimensions for reliable integration With a body length of L: 34 mm, an inner bore d: 11 mm and an outer diameter D: 26 mm, the collet combines compact form with robust clamping capability. The clamping‑diameter bridging is defined as nominal size minus 1.0 mm, allowing the collet to compensate for a small amount of variation and maintain a secure grip. Because tools are held along the whole clamping length, axial play is minimised and concentricity is preserved, which helps maintain process stability during higher spindle speeds or when using slender tooling. Operational benefits for workshop productivity Reliable repeatability and the ability to clamp on the tool lead chamfer reduce set‑up adjustments and rework, improving first‑pass yield on production runs. The combination of standard compliance, compact geometry and low runout supports efficient changeovers and predictable machining outcomes, which contributes directly to lower micro‑vibration and reduced scrap. For procurement and maintenance teams, the clear technical parameters simplify specification and reordering, while workshop operatives benefit from the straightforward handling and secure clamping behaviour. For tailored advice or to secure the TECWERK ER 25 collet for immediate integration, contact Metav Werkzeuge in Emmerich by phone +49 2822 7131930 or email info@metav-werkzeuge.com — experts on precision tooling and workshop supply are available to assist. Technical data Article number: 2000832932NW Type: ER 25 Label: Spannzange Typ ER 25/430 E Spann-D.11mm TECWERK Product type: ER collet Manufacturer: TECWERK Core data Clamping diameter (d): 11 mm Outer diameter (D): 26 mm Length (L): 34 mm Runout / repeatability: 5 µm Spannbereich: 11 Clamping‑diameter bridging: nominal minus 1.0 mm Special features Conforms to DIN 6499‑B Suitable for ER 25 collet chucks Tools held along the full clamping length Can be clamped on the lead chamfer Designed for precision runout and repeatability FAQ What chuck types is this collet compatible with? This collet is designed for use with ER 25 collet chucks and conforms to DIN 6499‑B, ensuring standardised compatibility in ER 25 systems. What does the clamping‑diameter bridging of 'nominal minus 1.0 mm' mean? It indicates the collet can compensate for up to 1.0 mm below the nominal diameter, allowing secure clamping across a small range of tool diameters while maintaining concentricity. How important is the 5 µm runout specification? A 5 µm runout figure denotes tight concentricity, which reduces vibration, improves surface finish and prolongs tool life when the collet is used in appropriate ER 25 setups. Can the collet clamp on the tool chamfer? Yes, the design permits clamping on the tool lead chamfer as well as along the full clamping length, offering flexibility in how tools are seated and secured. Manufacturer / Responsible: NORDWEST Handel AG, Robert‑Schuman‑Straße 17, 44263 Dortmund
11mm ER32 Collet Precision Clamping, 5 µm Runout, L 40mm - TECWERK
Benefit from precise clamping and effortless integration: the ER 32 collet offers 5 µm runout repeatability and secures tools over the full clamping length, while an 11 mm bore and compact 40 mm length ensure dependable performance in ER 32 setups. Order the collet directly via Metav Werkzeuge or consult the technical team for application advice. Collet ER 32/470 E – clamping Ø 11 mm (TECWERK) Collet ER 32/470 E is a precision ER 32 collet engineered for secure toolholding in milling and drilling operations, compatible with ER 32 collet chucks. DIN 6499-B standard compliance High runout repeatability 5 µm Full-length tool retention Clamping diameter 11 mm, length 40 mm Precision clamping for consistent machining The ER 32 collet is manufactured to deliver stable toolholding with a documented roundness and repeatability of 5 µm, which translates into fewer rejected parts and longer tool life. Conformance to DIN 6499-B provides a verifiable standard for interchangeability and quality, giving procurement and production planners a factual basis for integration. Tight runout control reduces vibration and improves surface finish, making the component well suited for high-precision tasks in series production and job-shop environments. This level of accuracy supports predictable machining cycles and fewer rework stages. Seamless integration with existing ER 32 systems Designed to mate with standard ER 32 chucks, the collet accepts an 11 mm clamping diameter and bridges minor size differences (nominal minus 1.0 mm) without intermediate adapters. Tools are gripped along the full clamping length, and the geometry permits clamping on the lead chamfer, simplifying setup when facing slightly varying tool shanks. The compatibility reduces changeover complexity and eliminates the need for special sizing rings, supporting efficient tooling logistics and straightforward retrofit into current toolholding assemblies. Robust handling and quick set-up for workshop routines With an overall length of 40 mm and an outer diameter of 33 mm, the collet balances compactness with sufficient gripping surface to maintain stability under load. The design ensures tools are held securely along their effective length, which helps maintain concentricity during heavy cuts and repeated cycles. Mechanical handling is intuitive for qualified staff: insertion, compression and release follow established ER collet practices, so process familiarity shortens training time and minimises production interruptions. Operational advantages that improve throughput Reliable clamping and standardised dimensions contribute directly to cycle-time stability and reduced scrap rates. The combination of standard conformity, easy integration and measurable repeatability supports a rational investment decision: better part quality and reduced downstream inspection effort. For production planners and workshop managers, the collet represents a practical component that enhances process reliability while fitting existing ER 32 toolholding ecosystems. For supply and technical guidance on integrating the TECWERK ER 32/470 E collet into existing toolholding systems, contact Metav Werkzeuge for direct procurement and application support via info@metav-werkzeuge.com or call +49 2822 7131930. Technical data Article number: 2000832947NW Brand: TECWERK Product: ER 32 collet Label: Spannzange Typ ER 32/470 E, clamping Ø 11 mm Package unit: 1 Core dimensions Clamping bore (d): 11 mm Length (L): 40 mm Outer diameter (D): 33 mm Roundness / repeatability: 5 µm Clamping diameter bridging: nominal minus 1.0 mm Design and features Conforms to DIN 6499-B Fits ER 32 collet chucks Tools held over full clamping length Can be clamped on the lead chamfer Suitable for standard workshop and industrial use FAQ What clamping diameter does this collet accept? The Collet ER 32/470 E (TECWERK, SKU 2000832947NW) accepts an 11 mm clamping diameter and is intended for use within that nominal range. Is the collet compatible with ER 32 chucks and standards? Yes. The collet is manufactured to DIN 6499-B, ensuring compatibility with ER 32 collet chucks and interchangeability in standard systems. What runout or repeatability can be expected? Typical roundness and repeatability for the collet are specified at 5 µm, offering stable concentricity for precision machining tasks. Can tools be gripped along the entire length and on the chamfer? Yes. The design allows tools to be clamped over the full clamping length and on the lead chamfer, enabling secure retention for varying shank conditions. Manufacturer/Responsible: NORDWEST Handel AG, Robert-Schuman-Straße 17, 44263 Dortmund
11mm Quick-Change Insert SE 11mm×9mm Gr.2 for DIN 374/376 M14, 5mm L3 - TECWERK
Benefit from rapid tool changes and reliable torque transfer: the insert combines a quick-change clamping interface with a 9 mm square shank and an 11 mm nominal diameter, making it suitable for taps to DIN 374/376 M14 and helping to reduce downtime. Order this quick-change insert directly via Metav Werkzeuge or ask our consultants if needed. Quick-change insert SE 11 mm x 9 mm Gr.2 — Quick-change insert for DIN 374/376 M14 taps, TECWERK A Quick-change insert SE 11 mm x 9 mm Gr.2 designed for secure retention of thread taps in quick-clamping systems, providing consistent engagement and simple integration into existing toolholders. Quick-change design for fast tool swaps Torque via 9 mm square shank Compatible with DIN 374/376 M14 taps No safety coupling for straightforward clamping Faster changeovers with dependable torque transfer The quick-clamp concept of this insert focuses on reducing non-productive time: the quick-change mechanism keeps the tap held firmly by the clamping device so that insert swaps can be completed noticeably faster than conventional collet setups. Torque is transmitted via the 9 mm square shank, which prevents slippage and ensures repeatable rotational force during tapping operations. This combination supports a smoother production flow and reduces the risk of thread errors caused by tool movement under load. Consistent thread quality through correct fit and retention Designed for use with taps to DIN 374/376 M14, the insert maintains axial and radial alignment during cutting, which helps to improve thread consistency across batches. The holding principle—taps secured in the quick-clamping pocket—reduces lateral play and contributes to improved concentricity. Because different shank dimensions require different inserts, the system philosophy promotes targeted selection of the correct insert to match the tap shank and the machine interface, avoiding mismatches that can lead to premature tool wear. Compact dimensions for straightforward workshop integration The insert’s compact geometry eases installation into standard quick-change toolholders and supports simple stock management. Key dimensions and lengths allow planners to verify fitment rapidly: the external diameters and lengths are adapted to common toolholder envelopes, while the absence of a safety coupling keeps the mechanical design straightforward and low-maintenance. This makes the insert suitable for retrofit situations as well as new tool assemblies, providing a practical balance of accessibility and mechanical reliability. For reliable tapping operations choose the TECWERK quick-change insert and contact Metav Werkzeuge for supply and application advice from Emmerich; email info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: 4000832645NW Manufacturer: TECWERK Product: Quick-change insert SE Type/Size: Größe 2 SKU/UID: 4000832645NW Packaging unit: 1 Suitable for: DIN 374/376 M14 Key measurements Diameter: 11 mm Square shank: 9 mm D: 48 mm D1: 31 mm L1: 32 mm L3: 5 mm L4: 35 mm L5: 11 mm Design / special features No safety coupling Inserts hold taps via quick-clamping device Torque transmission via shaft square Different inserts required for different shank sizes Intended for holding thread taps FAQ Which taps are compatible with this quick-change insert? The quick-change insert is specified for taps to DIN 374/376 M14 and is intended to hold thread taps that match that standard. How is torque transferred from the holder to the tap? Torque transmission is via the 9 mm square shank; this square drive on the insert ensures secure force transfer without slip during tapping. Does the insert include a safety coupling? No, the insert is supplied without a safety coupling; the design focuses on direct clamping and straightforward mechanical engagement. What should be considered when selecting a different insert size? Different tap shank dimensions require matching inserts; choose an insert that corresponds to the tap shank to maintain correct alignment and torque transfer. Is the insert suitable for retrofitting into existing quick-change systems? Yes, the compact dimensions and standardised interface make the insert suitable for integration into compatible quick-clamping toolholders and retrofit applications. Manufacturer/Responsible: NORDWEST Handel AG, Robert-Schuman-Straße 17, 44263 Dortmund
11mm Quick-Change Insert SES 9mm Square, Adjustable Safety Torque Coupling, L3 24.5mm - TECWERK
Benefit from an adjustable safety clutch that limits torque to avoid tap breakage and a secure 9 mm square shank torque transmission compatible with DIN 374/376 M14; order the quick-change insert directly via Metav Werkzeuge or consult our specialists for integration advice. Quick-change insert SES 11 mm × 9 mm Gr.1 – adjustable safety clutch for DIN 374/376 M14 (TECWERK) The Quick-change insert SES 11 mm × 9 mm Gr.1 is a compact torque-limiting interface designed for M14 thread taps, enabling safer tapping operations and rapid tool exchange in production and workshop environments. Adjustable safety clutch for torque control Prevents thread tap breakage 9 mm square shank torque transmission Compatible with DIN 374/376 M14 taps Reduce tap breakage and keep production running The most immediate gain from an insert with an adjustable safety clutch is a measurable reduction in tap failures. By limiting the transmitted torque, the module protects the tap at the moment of thread jamming or sudden load peaks; this reduces unscheduled downtime and the need for costly rework. The torque is transferred via a square shank, ensuring a positive mechanical drive that minimises slippage and wear on the drive interface. For machine shops that run high volumes of tapping operations, the safety clutch converts into fewer production interruptions and more predictable cycle times. Seamless integration with standard tap toolchains Designed for compatibility with taps conforming to DIN 374/376 M14, this quick-change coupling slots into existing toolholders without major rework of the set-up. The insert’s modular approach means different shank sizes use matching inserts, preserving a standardised tool inventory while allowing the workshop to adapt to varying shank dimensions. Installation and replacement are straightforward, so the insert supports lean workflows and helps maintain throughput. The combination of precise torque limitation and a standardised interface enables controlled machining results and a consistent thread quality. Compact construction that speeds changeovers and protects tools A compact form factor reduces interference and simplifies handling during tool changes, which shortens non-productive time at the spindle. The design focuses on rapid exchange and robust torque transfer: the square drive transmits force reliably while the clutch disengages under overload, prolonging both tap life and the life of sockets and drive tools. The result is higher uptime, reduced tooling costs over time and a calmer planning horizon for maintenance cycles — benefits that add up in busy workshops and production lines. For a tailored recommendation on the TECWERK SES quick-change insert and assistance with selecting the correct shank size, contact Metav Werkzeuge — phone +49 2822 7131930 or email info@metav-werkzeuge.com Technical data Article number: 4000832673NW Product: Quick-change insert SES Label: Quick-change insert SES 11 mm × 9 mm Gr.1 for DIN 374/376 M14 Manufacturer: TECWERK Facts Diameter: 11 mm Square shank: 9 mm L3: 24.5 mm L4: 21.5 mm L5: 25.5 mm D: 32 mm L1: 18.5 mm D1: 19 mm Packaging unit: 1 Special features Adjustable safety clutch for torque limitation Prevents thread tap breakage Torque transmission via shank square For use with DIN 374/376 M14 thread taps Different inserts required for other shank sizes FAQ Is the insert compatible with M14 taps to DIN 374/376? Yes. The Quick-change insert SES 11 mm × 9 mm Gr.1 is specified for taps conforming to DIN 374/376 M14 and transmits torque through a 9 mm square shank. How does the adjustable safety clutch reduce tap failures? The clutch disengages or slips at a preset torque, interrupting peak loads before a tap fractures; this mechanism on the SES insert protects the tap and connected drive components. Can the torque limit be adapted to different materials or tap sizes? Torque settings can be adjusted to suit common tapping scenarios, allowing optimisation for softer or harder workpiece materials and for varying thread sizes used with the SES insert. Are different inserts needed for other shank dimensions? Yes. The SES system uses inserts matched to the shank dimension; different square-shank sizes require the corresponding insert to ensure correct torque transmission. What dimensions should be checked before ordering? Verify the drive square (9 mm), the nominal diameter (11 mm), and the relevant length dimensions (L1, L3, L4, L5) to ensure compatibility with the toolholder and tap depth. Manufacturer / Responsible: NORDWEST Handel AG, Robert-Schuman-Straße 17, 44263 Dortmund
11mm Quick-Change Insert SES 9mm Square, Adjustable Torque-Limit Coupling for DIN 374/376 M14 - TECWERK
Take advantage of precise torque control and a compact, service-friendly design to protect taps and reduce downtime; order directly via Metav Werkzeuge or consult the team for application advice. Quick-change insert SES 11 mm x 9 mm, Size 2 – adjustable safety coupling (TECWERK) Quick-change insert SES 11 mm x 9 mm Size 2 provides a torque-limiting adapter for thread tapping applications, designed for use with DIN 374/376 M14 taps and workshop toolholders Adjustable safety coupling for torque limitation Prevents tap breakage during threading Compatible with DIN 374/376 M14 taps 9 mm square drive for positive torque transfer Reduce tool breakage and maintain production flow The adjustable safety coupling built into this quick-change insert limits torque transmission when resistance rises unexpectedly, significantly reducing the risk of tap breakage. As a result, thread production becomes more reliable and less prone to costly stoppages; the mechanism disengages before a tap sustains irreversible damage, protecting consumables and avoiding rework. This measurable reduction in scrap and downtime translates into better throughput and lower total operating cost per threaded component. Precise torque control for consistent threads Torque is transferred through the 9 mm square drive, ensuring a positive, backlash-free connection between driver and tap shank; the torque-limiting element is adjustable to suit the thread size and material conditions. Because the torque is controlled mechanically rather than electronically, the system reacts instantly to overloads and maintains thread quality across batches. The result is repeatable, consistent threads with fewer rejects and a predictable process window for production planners and workshop engineers. Compact design that integrates with existing tooling With a compact footprint (D 50 mm, D1 31 mm, L1 32 mm) and a nominal diameter of 11 mm, the insert fits into common toolholders while keeping the working envelope small. The torque is transmitted over the shaft square, so different shank dimensions require corresponding inserts; this modular approach lets maintenance teams replace only the worn insert instead of the entire driver assembly. The compact size and standard interface simplify storage and logistics in busy workshops. Engineered for workshop practicality and safety The unit is supplied as a single-piece package and is intended for quick replacement when wear occurs. The mechanical limiting principle provides a clear operational advantage: fast recovery after an overload without complex reset procedures. Documentation and simple adjustment make the insert suitable for both production environments and skilled maintenance teams that demand robust, service-friendly components from a recognised supplier. For tailored advice on integrating the TECWERK SES quick-change insert into existing tapping stations, contact Metav Werkzeuge for specification support and ordering assistance. Product data Article number: 4000832679NW Product type: Quick-change insert SES Size: Size 2 Brand: TECWERK Suitable for: DIN 374/376 M14 Dimensions & core data Diameter: 11 mm Square drive: 9 mm L1: 32 mm L3: 30.5 mm L4: 35 mm L5: 34 mm D: 50 mm D1: 31 mm Packaging unit: 1 Special features Adjustable safety coupling for torque limitation Torque transfer via shaft square Prevents tap breakage Requires matching inserts for other shaft sizes FAQ Which tap types are compatible with this quick-change insert? The quick-change insert SES 11 mm x 9 mm Size 2 is compatible with taps to DIN 374/376 M14 and designed to interface with standard tap shanks using the 9 mm square drive. How does the adjustable safety coupling work? The adjustable safety coupling in the TECWERK SES insert mechanically limits torque transmission; when the set torque is exceeded, the coupling slips to prevent damage to the tap and driver. Is a special driver required to use this insert? No special driver is required beyond a matching toolholder that accepts the SES interface and the 9 mm square drive; different shank sizes call for the corresponding insert variant. Can the torque setting be changed during operation? Torque adjustment is performed using the coupling mechanism; settings should be adjusted when the tool is stationary and according to workshop safety procedures. What dimensions should be checked before ordering? Verify the square drive (9 mm), the overall diameter (11 mm) and the key envelope dimensions (D 50 mm, L1 32 mm) to ensure compatibility with existing holders and clearance conditions. Manufacturer/Responsible: NORDWEST Handel AG, Robert-Schuman-Straße 17, 44263 Dortmund
12 mm T-Slot Nut Single With M10 Thread - Vertex
Take advantage of a compact, precisely fitted solution that matches 12 mm T-slots and secures with an M10 thread for consistent fixturing. The single-piece design reduces setup variability and supports a smooth production flow; order this T-slot insert directly via Metav Werkzeuge or consult our specialists for application advice. T-slot insert 3423M by Vertex — 12 mm T-slot, M10 thread T-slot insert 3423M is a compact fixing element for machine tables and fixtures, designed to fit 12 mm T-slots and to be secured with an M10 threaded fastening Fits 12 mm T-slots M10 threaded fastening Single-piece construction Compact dimensions 11.7 x 22 x 7 mm Faster, more reliable set-ups through precise fit A precisely dimensioned 12 mm T-slot interface combined with an M10 thread ensures the insert locates and clamps without guesswork, shortening set-up times and reducing rework. The compact footprint (11.7 x 22 x 7 mm) provides a snug engagement in standard T-slots so that alignment is preserved between cycles. For engineering teams pursuing repeatability, the result is consistent part positioning and fewer interruptions in the production chain. Secure clamping that improves process stability The single-piece construction removes joints and mating tolerances that can introduce play, delivering a secure anchorage for fixtures and stop elements. Using an M10 threaded fixing gives dependable clamping force while allowing straightforward replacement or repositioning when fixture layouts change. These attributes translate into measurable operational benefits: reduced downtime during changeovers and improved component tolerances through stable fixturing. Compact design for versatile fixture layouts Small overall dimensions and a low profile make this insert suitable for dense fixture arrangements and retrofits on existing machine tables. The compact form allows tighter packing of clamping points without sacrificing stability, enabling designers to create more flexible and space-efficient fixturing solutions. Sourcing from an established brand contributes to consistent part-to-part quality and predictable behaviour in daily shop-floor use. Contact Metav Werkzeuge for tailored advice on Vertex T-slot inserts and to secure supply from our Emmerich quality hub Technical data SKU: 3423M GTIN: 4061905086793 ECLASS: 21029107 Core specifications Dimensions: 11.7 x 22 x 7 mm T-slot compatibility: 12 mm Thread: M10 Design & special features Single-piece design Intended for T-slot fixturing Brand: Vertex FAQ Which T-slot size does the insert suit? The insert is specified for 12 mm T-slots; the 3423M by Vertex matches standard 12 mm slot systems. What mounting thread is used for fastening? Mounting is via an M10 thread, providing a secure and widely compatible fastening option for fixtures. Is the material of the insert stated? Material is not specified in the provided product data for the 3423M T-slot insert; consult Vertex documentation for material and mechanical properties. Can the insert be used for dense fixture arrangements? Yes, the compact dimensions (11.7 x 22 x 7 mm) and low profile make the insert suitable for tight fixture layouts and retrofits. How does the single-piece construction benefit fixturing? Single-piece construction reduces tolerance stack-up and potential play, yielding more stable clamping and better repeatability in production setups. Manufacturer: Vertex Machinery Works Co., Ltd.; No. 296, Sec. 1, Feng Shih Road, Fengyuan District, Taichung City 420, Taiwan
12,000N Pull Rod Clamp, 29,000N Hold Force, 20mm Piston Ø, Zinc Plated Cast Body - Kukamet
Take advantage of the combination of robust 12,000 N clamping force, a zinc‑plated cast body and a horizontal‑foot mounting for dependable, repeatable workholding in serial production and jigs. Order the push‑rod clamp directly via Metav Werkzeuge or ask the consultants for application advice. Push‑rod clamp 533 by Kukamet — horizontal foot, 12,000 N clamping force Push‑rod clamp 533 is a horizontal‑foot clamp designed for secure, repeatable workholding in machining, assembly and fixture applications. Horizontal-foot mounting for stable positioning Max clamping force 12,000 N Holding force up to 29,000 N Zinc-plated cast body for corrosion resistance Consistent clamping that keeps processes running The 533 push‑rod clamp delivers a clearly defined 12,000 N clamping force with a 29,000 N holding capacity, which supports stable fixturing under dynamic loads. The combination of a compact actuator and a 20 mm piston diameter produces predictable force transmission, making cycle‑to‑cycle repeatability straightforward to calculate for process planning. Where tight tolerances or frequent part changes are involved, the clamp’s clear performance figures enable reliable fixture design and reduced setup time through engineering‑led choices rather than trial and error. Designed for durability and quick integration on the shopfloor A zinc‑plated cast body provides resistance to workshop environments while keeping maintenance effort low. The horizontal‑foot mounting simplifies installation into existing fixtures or modular clamping plates, and the M10x70 pressure spindle ensures compatibility with common threaded components. With a compact mass of 1.61 kg, the unit is easy to handle during assembly yet robust enough for continuous use, offering a favourable balance between portability and structural integrity for small to medium‑scale production runs. Clear technical values that aid decision making Measured parameters such as clamping force, holding force and piston diameter translate directly into engineering decisions: clamp spacing, actuator count and cycle speed. The 533’s numeric specifications enable a rational evaluation of whether the component meets the required safety margins and throughput targets. For integrators and production engineers, these objective data points support efficient material planning and risk assessment, reducing downtime caused by under‑specified workholding. Contact Metav Werkzeuge for tailored application advice and to secure supply of the Kukamet Push‑rod clamp 533; the Metav team in Emmerich will assist with selection and delivery logistics Technical Data Article number: 533-5-Q20 GTIN: 8680731506136 Eclass: 21041716 ETIM: EC011973 Facts Max clamping force: 12,000 N Holding force: 29,000 N Piston diameter: 20 mm Pressure spindle: M10x70 Weight: 1.61 kg Special features Material: Zinc‑plated with cast body Mounting: Horizontal foot Category: Clamp (Spanner) SKU: 533-5-Q20 FAQ What tasks is this clamp best suited for? The Kukamet push‑rod clamp 533 is suited for machining, assembly and jig work where a horizontal mounting and defined clamping values are required; it is commonly used in fixtures for repeatable production tasks. How do the clamping and holding forces differ in practice? The clamp offers a 12,000 N clamping (actuating) force and a 29,000 N maximum holding capacity; the first figure describes applied force during actuation, the second the static retention the fixture can maintain under load. What mounting and connection details are required for installation? This horizontal‑foot model is designed for secure bolting to fixture plates; the unit uses an M10x70 pressure spindle and compact footprint to integrate with common clamping systems. Is the exterior treated to resist workshop wear? Yes, the push‑rod clamp 533 features a zinc‑plated finish on a cast body to enhance corrosion resistance and lengthen service life in workshop environments. Which numeric values are most important when designing a fixture with this clamp? Key values are the 12,000 N clamping force, 29,000 N holding force, 20 mm piston diameter and the pressure spindle specification (M10x70); these determine spacing, actuator count and safety margins Manufacturer: Kukamet Fevzi Çakmak Mah.10644 Sk. No:61-63 42050 Karatay / KONYA TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com
12/20mm Keyway Block For Fixed Mounting, Suitable For M6 x 10, H2mm - AMF
Take advantage of precise fixture alignment and secure thread compatibility for stable clamping in mixed-slot machine tables; order directly via Metav Werkzeuge or consult the team for specification matching. T-slot nut No. 6322A — fixed-mount T-slot nut for 12/20 mm slots (AMF) The T-slot nut No. 6322A is a fixed-mount clamping component for machine tables and fixtures, designed for nominal T-slot widths of 12 mm and 20 mm and compatible with M6 x 10 fastenings. For 12 mm and 20 mm T-slots Compatible with M6 x 10 fasteners Designed for fixed mounting Secure clamping across machine and fixture slots The T-slot nut delivers a consistent mechanical interface where two different slot standards meet: a nominal 12 mm width on the machine side and 20 mm on the fixture side. This makes the component suitable for hybrid set-ups where adapters or stepped clamping rails are used. By matching the nominal slot dimensions, the element reduces lateral play and helps maintain repeatable positioning under load. The design supports conventional threaded fastenings and ensures that a standard M6 x 10 screw achieves the required clamp force without the need for special bolts or washers. Simple installation and compatibility benefits Installation is straightforward: the element accepts an M6 x 10 fastener and is intended for fixed mounting in the slot system, removing the need for complex alignment during assembly. Because the component is tailored to the two nominal slot widths, it provides mechanical compatibility between machine tables and dedicated fixturing plates. For procurement and system planning, the single-piece supply format simplifies stock keeping and allows planners to order the exact quantity required for assembly lines or jigs. Practical advantages for workshop and production use Using a dedicated T-slot nut that matches both machine and fixture slot dimensions reduces set-up time and minimises rework caused by ill-fitting clamping hardware. The part supports efficient tool changes and fixture swaps by providing a repeatable datum for clamping points. Where repeatability and minimised downtime are priorities, the component contributes to smoother production flow and predictable assembly outcomes, particularly in mixed-standard environments common in retrofit and modular fixturing. For reliable clamping in mixed-slot setups, order the AMF T-slot nut No. 6322A through Metav Werkzeuge and request specialist advice from the Metav team to ensure full compatibility with existing tables and fixtures. Technical data Article number: 4000833234NW SKU: 4000833234NW Type: Nr. 6322A Label: Nutenstein Nr.6322A Nennmaß der Nut 12/20mm z.Festmontage AMF Manufacturer: AMF Product type: T-slot nut Packaging unit: 1 UID: 4000833234NW Facts Nominal slot (machine): 12 mm Nominal slot (fixture): 20 mm Suitable for: M6 x 10 Special features Fixed-mount design Compatible with mixed slot standards (12 / 20 mm) Designed for standard M6 x 10 fastenings Supplied as single unit FAQ Which slot widths does this component fit? The T-slot nut No. 6322A fits nominal slot widths of 12 mm on the machine side and 20 mm on the fixture side, providing compatibility where both standards occur. What fastener size is required for mounting? Mounting requires an M6 x 10 fastener; the T-slot nut is designed to accept this standard metric screw for secure clamping. Is the T-slot nut intended for adjustable or fixed mounting? This variant is designed for fixed mounting, intended to be secured in place rather than used as a freely sliding T-slot nut. Can the part be used to bridge different fixture systems? Yes — because it addresses both 12 mm and 20 mm nominal slot dimensions, the component is suitable for bridging machine tables and fixture plates that use differing T-slot standards. How is the product supplied? The item is supplied as a single unit, allowing direct replacement or specific-count ordering for assembly needs. Manufacturer: AMF; Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
1200 N Pneumatic Clamp Horizontal Base 95° Swing, Zinc-Plated, 1400 N Holding Force - Kukamet
Reliable, compact clamping with a 1,200 N pneumatic actuation and a zinc-plated finish delivers consistent holds and long service life, supporting steady production cycles and reduced setup times. Order the Pneumatic clamp 611 directly via Metav Werkzeuge or ask our consultants if needed. Pneumatic clamp 611 — Kukamet · 1.2 kN actuation · horizontal-foot mounting A Pneumatic clamp 611 designed for secure workpiece clamping in production and workshop settings, combining controlled pneumatic actuation with a corrosion-resistant finish and a compact horizontal-foot mount. Max. clamping force 1,200 N Holding force up to 1,400 N Zinc-plated corrosion resistance Horizontal-foot mounting, 95° angle Consistent actuation for predictable cycle times The pneumatic drive delivers a controlled actuation of 1,200 N, providing a repeatable closing movement that reduces variation between cycles and minimises manual adjustment. With a separate holding force of 1,400 N, the device secures parts reliably once clamped, which helps to prevent slippage during machining or assembly. The clear separation of actuation and holding values makes performance easy to specify for jigs and fixtures, supporting process planning and quality assurance in series production. Durable finish and compact installation save space A zinc-plated finish provides corrosion protection appropriate for workshop environments, while the low mass (approx. 0.535 kg) keeps the clamp compact and easy to integrate into fixtures. The horizontal-foot mounting with a 95° angle allows direct attachment to plates or subframes and supports low-profile installations where clearance is limited. These design choices reduce the need for additional brackets and simplify retrofits, lowering installation time and material handling effort. Seamless integration into clamping systems and fixtures Engineered for fixture-level use, the clamp is compatible with standard clamping arrangements and can be arranged in arrays for multi-station jigs. The compact pneumatic actuator allows straightforward connection to existing compressed-air supplies, enabling controlled operation without extensive electrical integration. Identification by SKU and GTIN supports inventory management and procurement tracking for production planners and purchasers seeking reproducible component sourcing. For tailored advice on integrating the Kukamet Pneumatic clamp 611 into workshop fixtures, contact Metav Werkzeuge for delivery from Emmerich and expert consultation at +49 2822 7131930 or info@metav-werkzeuge.com Technical data SKU: 611-2 GTIN: 8680731502893 Article designation: Pneumatic clamp / 611 Manufacturer: Kukamet Facts Max. actuation force: 1,200 N Max. holding force: 1,400 N Weight: 0.535 kg Angle: 95° Special features Zinc-plated finish Horizontal-foot mounting Mounting type: waagerechter Fuß Category: Clamps eCl@ss: 21021004 ETIM: EC011973 FAQ What clamping and holding forces does the clamp provide? The Kukamet Pneumatic clamp 611 offers a maximum actuation force of 1,200 N and a holding force of 1,400 N, values intended for reliable part retention in fixtures. How is the clamp mounted to a fixture? Mounting is via a horizontal foot (waagerechter Fuß); the clamp’s design and 95° angle suit low-profile attachment to plates and subframes. Is the surface finish suitable for workshop environments? The clamp features a zinc-plated finish, providing corrosion resistance suitable for typical production and workshop conditions. How compact is the device for multi-station fixtures? With a weight of approximately 0.535 kg and a compact actuator, the clamp is well suited for installation in arrays or confined fixture spaces. Can the clamp be integrated into existing pneumatic systems? Yes; the clamp’s pneumatic actuation is designed for straightforward connection to standard compressed-air supplies and can be incorporated into existing clamping circuits. Manufacturer: Kukamet Fevzi Çakmak Mah.10644 Sk. No:61-63 42050 Karatay / KONYA TÜRKİYE / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com
1200 N Vertical Clamp Stainless Steel Wafer Base Wafer-Type, 1400 N Holding Force - Kukamet
The combination of stainless steel construction, a 1,200 N clamping capacity and a compact horizontal base delivers reliable, corrosion-resistant workholding for jigs and fixtures; order the clamp directly via Metav Werkzeuge or consult the technical team for application advice. Vertikalspanner 211 — Vertical toggle clamp with stainless steel body and 1,200 N clamping force (Kukamet) The Vertikalspanner 211 is a compact vertical toggle clamp designed to secure workpieces in jigs, fixtures and assembly stations where a durable, low-profile hold is required. Stainless steel construction 1,200 N clamping force Horizontal base for secure mounting M6x40 pressure spindle Robust clamping that keeps production moving Built from stainless steel, this vertical toggle clamp provides a corrosion-resistant and wear-tolerant solution for repetitive clamping tasks. With a 1,200 N maximum clamping force and 1,400 N holding capacity, the unit secures components with consistent pressure, reducing repositioning and rework. The simple mechanical design translates into predictable performance during machining and assembly operations, supporting steady throughput and fewer interruptions. Space-saving mounting for tight fixtures The horizontal base allows direct bench or fixture mounting where vertical clearance is limited, enabling flexible placement in confined jigs. Weighing just 0.23 kg and equipped with an M6x40 pressure spindle, the clamp is suitable for compact tooling layouts and keeps added mass to a minimum, which benefits moving assemblies and reduces inertial load on automated stations. The standard M6 spindle also simplifies integration with existing locating hardware. Low-maintenance design for dependable service life With no special coatings or complex mechanisms, the clamp offers straightforward upkeep and dependable repeatability. The stainless-steel body minimises the need for frequent replacement in humid or light-corrosive environments, while the plain spindle thread supports easy part replacement. This results in low maintenance, longer intervals between service actions and reduced total cost of ownership for workshop and production environments. Contact Metav Werkzeuge for a supply estimate or to arrange a technical consultation on the Kukamet vertical toggle clamp 211 — email info@metav-werkzeuge.com or call +49 2822 7131930 Technical data SKU: S211-2 GTIN: 8680731504002 Manufacturer: Kukamet Facts Clamping force (max): 1,200 N Holding force (max): 1,400 N Weight: 0.23 kg Pressure spindle: M6x40 eClass: 21041717 ETIM: EC011973 Special features Material: stainless steel Mounting: horizontal base Designation: Vertikalspanner 211 Arm: Not applicable Special feature: None FAQ What maximum clamping force does the clamp provide? The clamp delivers a maximum clamping force of 1,200 N; the holding capacity is rated at 1,400 N for secure retention under load with the Vertikalspanner 211. Is the clamp suitable for corrosive or humid environments? Yes, the stainless steel construction provides enhanced corrosion resistance, making the clamp appropriate for humid or mildly corrosive workshop conditions. How is the clamp mounted to a fixture or bench? Mounting is via a horizontal base, allowing secure attachment to flat surfaces and jigs; the horizontal base is designed for simple integration into existing fixture plates. What is the pressure spindle specification and how does it affect installation? The clamp uses an M6x40 pressure spindle, a standard metric thread that simplifies replacement parts and makes alignment adjustments straightforward during installation. Can the clamp be used in automated assembly lines? The compact mass (0.23 kg) and predictable toggle action make the clamp suitable for use in automated or semi-automated assemblies where compact, repeatable workholding is required. Manufacturer: Kukamet Fevzi Çakmak Mah.10644 Sk. No:61-63 42050 Karatay / KONYA TÜRKİYE / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com
1200 N Vertical Clamp With 1400 N Holding Force, M6x40 Screw, Black Oxide Finish - Kukamet
The compact design and robust clamping values make this clamp a practical choice for confined fixtures: reliable 1,200 N clamping force combined with a secure 1,400 N holding capacity and an angle base for easy mounting. Order the 213 vertical clamp directly via Metav Werkzeuge or ask our consultants if needed. 213 Vertical Clamp by Kukamet — Angle-base lever clamp, 1,200 N clamping force 213 is a compact vertical lever clamp designed for secure vertical holding in jigs, fixtures and assembly stations, combining a small footprint with consistent clamping performance. Angle-base mounting for stable fixture Max clamping force 1,200 N Holding force 1,400 N Lightweight 0.265 kg for easy handling Reliable clamping where space is tight The compact lever design delivers a dependable 1,200 N clamping action while maintaining a minimal installation footprint. Its angle base mounting ensures stable attachment to plates and fixture frames, reducing lateral movement during operation. The device’s lightweight construction (0.265 kg) simplifies handling and placement in dense tooling setups, while the measured 1,400 N holding capacity provides secure retention for small to medium workpieces. This combination of compactness and force supports faster set-ups and fewer fixture adjustments. Built for repeatability and straightforward installation Engineered as a lever-style vertical clamp, the unit features a threaded pressure spindle sized M6x40, enabling fine adjustment of contact pressure and repeatable positioning. The mechanical principle delivers consistent clamping without complex adjustment routines, which minimises downtime between batches. The blackened finish affords a protective surface that resists light corrosion and reduces reflections in inspection areas. Where repeatable clamping and quick installation are priorities, this clamp streamlines fixture workflow and contributes to measurable gains in cycle reliability. Practical uses in production and assembly Suitable for use in jigs, holding fixtures and assembly benches, the vertical lever clamp secures components during machining, inspection and manual assembly tasks. The robust holding characteristic of the device makes it appropriate for small-scale machining operations and repetitive positioning tasks where consistent clamping force is required. As a component in modular fixture systems, the clamp integrates with plates and frames using the angle base mounting, offering a straightforward solution for both new jigs and retrofitting existing tooling. For dependable fixture performance, request supply of the Kukamet 213 vertical clamp through Metav Werkzeuge — delivered from Emmerich with application advice available via info@metav-werkzeuge.com or by phone on +49 2822 7131930 Technical Data SKU: B213-2 GTIN: 8680731507966 Manufacturer: Kukamet Facts Clamping force max: 1,200 N Holding force max: 1,400 N Weight: 0.265 kg Special features Mounting: Angle base Pressure spindle: M6x40 Finish: Blackened finish Category: Spanner / Lever clamp FAQ What is the maximum clamping force of this clamp? The clamp provides a maximum clamping force of 1,200 N and a holding capacity of 1,400 N for reliable retention during fixture work. How is the clamp mounted on a fixture plate? Mounting is via an angle base that offers stable attachment to plates and frames for secure installation in jigs and fixtures. Which spindle thread is fitted for pressure adjustment? The unit is supplied with a pressure spindle sized M6x40 to allow fine adjustment of contact pressure and accurate positioning. Is this clamp suitable for retrofitting existing fixtures? Yes, the angle-base design and compact form factor make it well suited for integration into existing modular fixtures and assembly stations. What finish does the clamp have and why is it useful? The clamp has a blackened finish which provides surface protection and reduces glare in inspection or optical setups. Manufacturer: Kukamet Fevzi Çakmak Mah.10644 Sk. No:61-63 42050 Karatay / KONYA TÜRKİYE / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com
Secure components with reliable workpiece clamps
Workpiece clamps, also known as workholding clamps or workholding devices, form the essential mechanical interface between machine and part in industrial fabrication. They keep components absolutely play-free, positionally accurate and vibration-resistant during milling, turning, drilling or grinding.
How workpiece clamps ensure process stability
A correctly specified clamping concept transfers the high cutting and feed forces of modern CNC machines into the machine table or spindle without deforming the part. The right combination of mechanical, hydraulic, pneumatic or magnetic solutions enables fast, repeatable setups and supports automated part change where required. Typical applications range from single-part turning to high-volume series milling and complex five-axis machining.
Concrete production benefits at a glance
- repeatable positioning: reduces scrap and rework
- high clamping forces: withstands aggressive cutting without part movement
- reduced set-up time: modular systems and quick-change features speed throughput
- improved surface finish: vibration damping for finer results and tighter tolerances
- flexible compatibility: vices, chucks, clamping plates and zero-point systems for diverse geometries
Why Metav's range is the practical choice
Metav combines decades of specialist know-how with a broad, handpicked range that democratises precision for workshops and industry alike. Based in Emmerich, Metav acts as a quality filter for the European market and supplies more than 250,000 products from precision metrology to complete workshop equipment. With the trust of over 48,000 customers, Metav offers a single-source approach that reduces supplier complexity and secures dependable delivery to your workbench.
Technical data
- function: mechanical interface between machine and workpiece
- primary requirements: absolute positional accuracy; vibration reduction; high clamping forces
- technologies: mechanical, hydraulic, pneumatic, magnetic
- typical components: machine vices; chucks; clamping plates; zero-point systems; pratzen; clamping jaws
- application areas: milling; turning; drilling; grinding; automated part change systems
- production benefits: reduced set-up time; enhanced process security; optimised series and single-part production
The practical summary
Workpiece clamps bring the stability and repeatability required to meet tight tolerances and excellent surface quality, making them indispensable across machining operations. Choosing the right workholding clamps and modular workholding devices is a decisive step towards higher productivity and consistent part quality.
FAQ
What types of workpiece clamps are suitable for automated machining?
Workholding clamps with quick-change modules, hydraulic actuation or magnetic systems are commonly used for automated machining. These workholding devices enable fast, repeatable part changes and integrate with zero-point systems.
How do workpiece clamps affect surface finish and tolerances?
A stable clamping concept minimises vibration and part movement; this improves surface finish and supports achieving narrow tolerances when using high-precision workpiece clamps or workholding devices.
Can the same workpiece clamps handle different part geometries?
Modular workholding clamps and adaptable clamping jaws allow flexible fixturing for varied geometries; combining vices, clamping plates and pratzen increases versatility on the shopfloor.
Fragen zu diesen Produkten??
Mit mehr als 30 Jahren Erfahrung beraten wir Sie gerne persönlich.
Tel.: +49 2822 7131930
Mail: info@metav-werkzeuge.com