Secure and precise workholding for metalworking productivity
Workholding devices such as workpiece clamps and chuck systems provide absolute positional stability and vibration damping during milling, turning, drilling and grinding, ensuring parts remain free of play under high CNC cutting and feed forces. By transferring clamping loads into the machine table or spindle without deforming the component, a well engineered workholding solution improves machining accuracy, surface finish and process reliability while reducing set-up times. Modular systems from machine vices and chucks to zero-point systems and specialised fixtures enable fast changeovers and support both serial and single-part production, delivering consistent clamping force, repeatability and enhanced throughput.
1700N Three-Point Push Rod Clamp 1.5kN Thrust Stainless Steel Without Base - Kukamet
Take advantage of a compact, corrosion-resistant clamp that delivers a holding force of 1,700 N and a maximum thrust of 1,500 N for reliable fixturing; its low weight and stainless construction make it ideal for repeatable production use. Order or request advice via Metav Werkzeuge for straightforward procurement and technical guidance. Push-rod clamp 513 by Kukamet — stainless steel, 1,700 N holding force The Push-rod clamp 513 is a compact stainless steel clamp engineered for secure holding and repeatable positioning in jigs, fixtures and short-run production equipment Stainless steel body for corrosion resistance Holding force up to 1,700 N Maximum thrust 1,500 N Compact 0.2 kg lightweight design Consistent clamping power for process reliability The 513 push-rod clamp provides reliable holding capacity with a rated holding force of 1,700 N and a maximum thrust of 1,500 N, delivering the mechanical restraint needed for machining, assembly and inspection operations. These figures indicate the static and dynamic loads the device withstands; higher holding and thrust values translate directly into fewer reworks and more consistent cycle outcomes. Where repeatability is required, the clamp offers repeatable positioning and stable force transmission, reducing setup time and downstream quality checks. Durable stainless design for workshop environments Constructed from stainless steel, this clamp resists corrosion in humid or solvent-exposed environments while maintaining dimensional stability. The lightweight 0.2 kg construction reduces fixture mass, aiding quick handling and minimising load on moving assemblies. The integrated pressure spindle is specified as M6x40, allowing fine adjustment of contact pressure and simple replacement with standard hardware. The absence of a base foot (mounting: without foot) permits installation in confined spaces or inline mounting directly into plates or fixture blocks. Fast integration and low-maintenance operation Designed for straightforward integration into production fixtures, the rod clamp combines a compact footprint with robust function. The stainless construction and simple mechanical design require minimal maintenance, supporting continuous operation in busy workshop settings. The clamp’s compact form factor and consistent mechanical performance enable efficient cycle times and predictable part registration, helping production engineers to streamline fixture design and reduce machine downtime. For specification checks, application advice or to request a quotation for the Kukamet push-rod clamp 513, contact Metav Werkzeuge in Emmerich: info@metav-werkzeuge.com or +49 2822 7131930 Technical data SKU: S513-2 GTIN: 8680731504194 Material: Stainless steel Weight: 0.2 kg Core specifications Holding force: 1,700 N Maximum thrust: 1,500 N Pressure spindle: M6x40 eCl@ss: 21041716 ETIM: EC011973 Features Mounting: without foot Clamp type: push-rod clamp Category: Spanner Manufacturer: Kukamet FAQ What loads can this clamp handle during machining? The Kukamet push-rod clamp 513 is rated for a holding force of 1,700 N and a maximum thrust of 1,500 N, suitable for many light to medium machining and assembly tasks. Is the clamp suitable for corrosive or humid environments? Yes. The clamp’s stainless steel construction provides enhanced corrosion resistance and is appropriate for harsher workshop conditions. How is contact pressure adjusted on this clamp? Adjustment is made via the pressure spindle (M6x40), which allows precise setting of contact height and pressure for consistent part holding. Can the clamp be mounted directly into a fixture plate? The 513 is supplied without a foot, enabling direct or inline mounting into plates or fixture blocks where a compact installation is required. What is the product identification for ordering or specification? Refer to the SKU S513-2 and GTIN 8680731504194 when specifying or ordering the Kukamet push-rod clamp 513. Manufacturer: Kukamet Fevzi Çakmak Mah.10644 Sk. No:61-63 42050 Karatay / KONYA TÜRKİYE / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com
171mm Reducing Sleeve MK5 to MK4 Hardened Ground DIN 2185 - TECWERK
Benefit from a robust adapter that combines DIN 2185 conformity with a fully hardened and ground finish and a precise MT5-to-MT4 taper transition for secure toolholding and minimal runout. The sleeve’s 171 mm overall length and internal/external machining ensure stable seating for Morse taper tools; order the reducing sleeve directly via Metav Werkzeuge or consult the team for application-specific guidance. Reducing sleeve DIN 2185 MT5→MT4 — TECWERK The Reducing sleeve DIN 2185 MT5→MT4 adapts tools with a Morse taper shank to larger machine tapers, offering a hardened and ground connection for reliable machining in workshops and industrial toolrooms. DIN 2185 compliant reducing sleeve Hardened and ground inside and out Adapts MT5 spindles to MT4 tools Total length 171 mm Precision fit for repeatable toolholding The adapter is manufactured to the DIN 2185 standard, which governs dimensions and tolerances for taper adapters; this guarantees a consistent interface between spindle and tool shank. With both the internal and external surfaces hardened and ground, the component reduces the risk of slippage and maintains concentricity under load. For production environments where repeatable positioning is essential, the hardened, ground finish delivers tangible improvements in runout stability and tool life. Versatile compatibility across machine applications Designed as a taper transition from MT5 (outer taper) to MT4 (inner taper), the sleeve permits the use of smaller-shank tooling in larger spindles without modifying fixtures or holders. The adapter’s 171 mm overall length provides sufficient engagement for secure seating while preserving access to cutting tools. The solution is suitable for turning, drilling and reaming tasks where Morse taper shanks are standard, making it a practical choice for maintenance shops and production lines alike. Durable construction that simplifies workshop logistics The component’s execution as a fully hardened and ground sleeve reduces surface wear and the need for frequent replacements, contributing to lower downtime and predictable maintenance intervals. By standardising on DIN-compliant adapters, procurement benefits from interchangeability and fewer bespoke parts. This approach supports efficient inventory management in toolrooms and helps streamline operations while assuring the mechanical integrity expected in demanding machining contexts. Contact Metav Werkzeuge for a specification check and secure the TECWERK reducing sleeve DIN 2185 MT5→MT4 for precise taper adaptation directly from our Emmerich distribution centre. Technical data Article number: 2000832361NW Standard: DIN 2185 Brand: TECWERK Facts Total length: 171 mm Inner taper: MT4 Outer taper: MT5 Packaging unit: 1 Special features Completely hardened and ground Suitable for tools with Morse taper shank Execution: hardened and ground FAQ What taper sizes does this adapter connect? The reducing sleeve connects an MT5 outer taper to an MT4 inner taper, allowing MT4-shank tools to be used in MT5 spindles; the TECWERK adapter is manufactured to DIN 2185 tolerances. Is the sleeve suitable for heavy-duty machining? With a fully hardened and ground construction, the sleeve is designed for demanding workshop conditions and supports secure seating under typical machining loads. How long is the adapter and why does length matter? The total length is 171 mm; this provides sufficient engagement for stable clamping and helps preserve concentricity between spindle and tool. Does the sleeve require special maintenance? Regular inspection for wear and light lubrication of contact surfaces is recommended; the hardened and ground finish of the reducing sleeve extends service life and reduces maintenance frequency. Manufacturer / Responsible: NORDWEST Handel AG, Robert‑Schuman‑Straße 17, 44263 Dortmund
1725N Holding Force Horizontal Base Toggle Clamp, Silicone-Coated Handle, Zinc Plated, 50mm Thread Length - Kukamet
Take advantage of a galvanised, compact latch that combines robust clamping performance with an ergonomic, silicone-coated handle for fast, repeatable fastening. The horizontal base and integrated hook provide secure mounting and quick engagement, making this clamp a practical choice for production jigs and workshop fixtures — order directly via Metav Werkzeuge or ask our consultants for advice. Toggle Latch Clamp 361 by Kukamet — horizontal base, silicone-coated handle A Toggle Latch Clamp 361 engineered for secure, rapid fastening in industrial jigs, fixtures and workshop applications with a horizontal base for stable mounting. Horizontal base for stable fixture mounting Silicone-coated handle for slip resistance Galvanised steel for corrosion resistance Up to 1,500 N clamping force Secure clamping for repeatable production The clamp provides a consistent 1,500 N clamping force with a holding capacity of 1,725 N, ensuring reliable retention of parts during processing and transport. In practice, these values mean fewer repositioning steps and less rework on assembly lines and fixture-based tasks. The measured clamping and holding figures support decisions in production planning and offer a verifiable basis for choosing a compact mechanical fastener for repeat operations. Ergonomic handling that speeds up workflows An ergonomically designed, silicone-coated handle improves grip and reduces operator fatigue during frequent clamping cycles. The horizontal base simplifies integration into fixtures and tooling plates, while the built-in hook enables quick engagement and secure latching without additional parts. These features translate to reduced cycle times and easier manual operation on the shop floor, supporting smoother interaction between operator and fixture. Robust construction for workshop conditions Constructed from galvanised steel, the fastener resists corrosion in humid or dusty environments, extending service life and lowering replacement frequency. The lightweight design (approximately 0.1 kg) and adjustable 50 mm thread length permit flexible installation and fine adjustment of clamp travel. Simple mechanical construction allows straightforward maintenance and inspection, contributing to dependable uptime in small-batch and continuous production settings. For reliable, slip-resistant fastening choose Kukamet's Toggle Latch Clamp 361 — contact Metav Werkzeuge for supply and technical advice from Emmerich: info@metav-werkzeuge.com or +49 2822 7131930 Technical data SKU: 361-2-K GTIN: 8680731504200 ECLASS: 21041718 ETIM: EC011973 Core measurements Max clamping force: 1,500 N Max holding force: 1,725 N Thread length: 50 mm Weight: 0.1 kg Materials and features Material: galvanised Silicone-coated handle Horizontal base With hook FAQ What clamping and holding forces does this latch provide? The latch delivers a clamping force of 1,500 N and a holding force of 1,725 N, values suitable for many jigs and fixture applications where secure retention is required. Is the clamp suitable for workshop environments prone to moisture? Yes, the galvanised construction gives the clamp corrosion resistance, making the Kukamet latch suitable for humid or general workshop conditions. How is the clamp mounted to a fixture plate? Mounting is via the horizontal base; the design allows straightforward integration into fixture plates and tooling with the thread and base fixing arrangement. Can the clamp travel be adjusted to different part heights? Adjustment is achieved through the threaded spindle (50 mm thread length) so the latch can be fine-tuned to varying part heights and clamping distances. Does the handle provide good grip for frequent operation? The silicone-coated handle enhances grip and reduces slippage during repeated cycles, improving operator comfort and consistency. Manufacturer: Kukamet Fevzi Çakmak Mah.10644 Sk. No:61-63 42050 Karatay / KONYA TÜRKİYE / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com
175mm Clamp Screw M24x3P, Heat-Treated Steel - Vertex
Take advantage of the combination of robust M24x3P threading, heat-treated steel construction and a compact 175 mm length for secure, repeatable clamping in workshop and production environments; order directly via Metav Werkzeuge or ask our consultants for specification support. Clamping screws — Vertex M24x3P hardened fastening screw, 175 mm The Clamping screws is a hardened fastening element intended for securing fixtures, jigs and workpieces in machining and assembly operations, combining coarse metric threading with a durable steel body for consistent restraint. Hardened steel construction Coarse M24x3P thread for strong grip Length 175 mm for deeper clamping reach Faster, more reliable set-ups with robust engagement The coarse M24x3P thread and heat-treated steel body deliver a reliable mechanical connection that reduces slippage and repeated retorquing during production. By relying on a single, sturdy fastening element, fixture assembly becomes more predictable; the combination of thread form and material hardness ensures a secure bite into mating components, lowering the risk of micro-movement under vibration. This results in fewer interruptions during machining and a smoother workflow on the shop floor. Durable design for repetitive industrial use Constructed from heat-treated steel, the clamp screw resists wear and retains clamping force over long service intervals. The 175 mm overall length provides sufficient reach for many common fixture geometries while keeping the component compact and easy to handle. With a mass of around 0.53 kg, handling and inventory storage remain straightforward. The solid construction reduces the need for frequent replacement, contributing to lower maintenance effort and predictable consumption planning for production environments. Practical integration and procurement advantages Designed for straightforward integration with standard clamping systems, the fastener supports repeatable fixturing routines and simplifies spare-part management. Supplied by a recognised brand, Vertex, and listed under SKU 1387M, the item is suitable for workshops seeking a dependable mechanical solution rather than temporary fixes. Metav’s purchasing and logistics approach supports reliable supply from Emmerich, backed by decades of distribution experience that helps keep production lines supplied with quality components and consistent lead times. Contact Metav Werkzeuge in Emmerich for specification advice or to arrange supply of Vertex clamping screws (SKU 1387M); email info@metav-werkzeuge.com or call +49 2822 7131930 for a tailored recommendation Technical data Article number: 1387M GTIN: 4061905091421 Manufacturer: Vertex Facts Weight: 0.53 kg Length: 175 mm Thread: M24x3P Materials / Special features Material: Heat-treated steel ECLASS: 21022190 Durable design for secure clamping and repeated use FAQ What material is the clamping screw made from? The clamping screw is manufactured from heat-treated steel; the Vertex fastening screw (SKU 1387M) is designed for durability in workshop and production settings. What are the thread and length specifications? Thread specification is M24x3P and the overall length is 175 mm; weight is approximately 0.53 kg. Is this fastening element suitable for repetitive machining applications? Yes, the hardened construction and coarse thread make it suitable for repetitive clamping tasks in machining and assembly processes. How is the item identified for ordering? The component is listed under SKU 1387M and GTIN 4061905091421 for straightforward ordering and stock control. Manufacturer: Vertex Machinery Works Co., Ltd.; No. 296, Sec. 1, Feng Shih Road, Fengyuan District, Taichung City 420, Taiwan
175mm Clamping Screw M10x1.5, Hardened Steel - Vertex
Take advantage of the combination of heat-treated steel construction, a standard M10×1.5 thread and a 175 mm length for reliable, repeatable clamping in jigs and fixtures. Order the clamping screw directly via Metav Werkzeuge or ask our consultants if further specification data is required. Clamping screw 1337M (M10×1.5, 175 mm) by Vertex The clamping screw 1337M is a heavy-duty fastening element designed for secure clamping in fixtures, jigs and machine setups across industrial and workshop environments. Heat-treated steel for durable clamping Thread M10×1.5 for standard fittings 175 mm overall length for deep engagement Precise manufacturing by Vertex for consistency Robust construction for dependable clamping A forged, heat-treated steel body delivers high deformation resistance and long service life in repetitive clamping applications. The component’s material treatment increases wear resistance and reduces the risk of thread damage during repeated tightening cycles, so the fastener maintains consistent clamping force over time. Such robustness supports uninterrupted production and reduces downtime associated with fastener replacement. Standardised thread for secure integration The M10×1.5 metric thread matches common fixture and tooling standards, enabling straightforward integration into existing assemblies without custom adapters. Standard pitch and diameter ensure predictable torque-to-clamping force behaviour, which is important for process reproducibility in batch production. Clear thread specification simplifies procurement planning and reduces the risk of mismatched components in maintenance routines. Deep engagement and balanced handling With a 175 mm overall length and a mass of approximately 0.09 kg, the fastener affords extended engagement depth where long reach or through-part clamping is required. The geometry is balanced to deliver strength without excessive weight, which eases handling during repetitive operations and supports ergonomic assembly workflows. This combination of length and mass contributes to stable clamping in multi-step machining or assembly processes. Consistent production quality and factory traceability Manufactured by Vertex to consistent tolerances, the fastener benefits production-grade quality control and repeatability. Precision machining and finishing reduce clearance variability and ensure a snug fit in mating components. For procurement departments seeking dependable repeat buys, the documented manufacturing source and SKU simplify inventory management and traceability in regulated environments. Contact Metav Werkzeuge in Emmerich for specification advice and to source the Vertex clamping screw 1337M directly from our European supply hub. Technical data Article number: 1337M GTIN: 4061905094422 Manufacturer: Vertex Facts Weight: 0.09 kg Thread: M10×1.5 Length: 175 mm Special features Material: Heat-treated steel Intended use: Clamping in fixtures and jigs Origin: Vertex production FAQ What thread and pitch does this fastener use? The clamping screw is specified with an M10×1.5 metric thread, suitable for standard M10 fittings in fixtures and tooling. Which materials is the fastener made from? This Vertex clamping screw is manufactured from heat-treated steel, chosen for wear resistance and long-term durability in industrial use. Is the length suitable for deep clamping applications? Yes, the 175 mm overall length provides extended engagement for through-part clamping and deep fixtures. Manufacturer: Vertex Machinery Works Co., Ltd.; No. 296, Sec. 1, Feng Shih Road, Fengyuan District, Taichung City 420, Taiwan
175mm Clamping Screw M12x1.75P Heat-Treated Steel, 0.13kg - Vertex
Take advantage of robust heat-treated steel construction combined with a metric M12x1.75 precision thread and an extended 175 mm length for dependable clamping in workshop fixtures; order the clamping screw directly via Metav Werkzeuge or ask our consultants if needed. Clamping screw »1347M« by Vertex — M12x1.75 thread, 175 mm, heat-treated steel The Clamping screw »1347M« is a heavy-duty fastening element designed for secure fixture and workpiece clamping in industrial and workshop environments, combining thread precision with durable material treatment for consistent performance. Robust heat-treated steel construction Metric M12x1.75 precision thread 175 mm overall length for deep clamping Compact weight 0.13 kg for easy handling Engineered for secure clamping and longevity The component is manufactured from heat-treated steel, a process that increases hardness and wear resistance while maintaining toughness. This treatment means the fastener resists deformation under torque and repetitive load cycles, which results in a longer service life and a lower frequency of replacement. The engineered surface integrity supports consistent clamping force and reduces the risk of thread wear in routine production use. Precision thread for reliable fixture interfaces A metric M12x1.75 thread guarantees compatibility with standard fixture nuts and tapped holes, offering repeatable engagement and reduced play in assemblies. The thread form and pitch are suited to industrial fastening requirements, enabling secure torque transfer and predictable clamp force. For maintenance planning, the standardised thread simplifies procurement and replacement, while the precise form reduces micro-movement that can cause fixture drift over time. Practical dimensions that support versatile applications With an overall length of 175 mm and a nett weight of 0.13 kg, the fastener is suited to deeper clamping positions and applications where reach and manageable handling are both required. The combination of length and balanced mass allows for comfortable manual operation and straightforward integration into automated clamping systems or custom jigs. The geometry supports accessibility in confined setups without compromising mechanical stability. Trusted manufacturing and supply chain confidence Produced by Vertex, the component carries clear product identification and traceability for workshop inventory: SKU and GTIN are provided for streamlined ordering and stock control. Delivered through Metav Werkzeuge, the offering benefits from a quality filter that serves the European market, backed by established logistics and a broad range of complementary precision components for single-source procurement. Contact Metav Werkzeuge for tailored advice and to secure the Vertex 1347M clamping screw through Metav Werkzeuge's specialists Technical Data Article number: 1347M GTIN: 4061905091506 Manufacturer: Vertex Facts Weight: 0.13 kg Length: 175 mm Thread: M12x1.75 Special features Material: Heat-treated steel Category: Vertex ECLASS: 21022190 FAQ What is the thread specification of this clamping screw? The clamping screw is supplied with a M12x1.75 metric thread, suitable for standard industrial fixtures and nuts. Which material is used for the 1347M and what does that mean for durability? The 1347M is made from heat-treated steel, which improves hardness and wear resistance for extended service life under repetitive clamping. Is the 1347M suitable for use in machine jigs and fixtures? Yes, the Vertex 1347M clamping screw is designed for fixture and jig applications where a precise thread and extended reach are required. How can the 1347M be identified when ordering spare parts? Use the article number 1347M or GTIN 4061905091506 when ordering to ensure exact identification and traceability. Manufacturer: Vertex Machinery Works Co., Ltd.; No. 296, Sec. 1, Feng Shih Road, Fengyuan District, Taichung City 420, Taiwan
175mm Clamping Screw M14x2P Heat-Treated Steel, 0.18kg - Vertex
Robust heat-treated steel construction, precise M14x2P threading and a 175 mm length ensure reliable clamping and long service life; combine the proven mechanical properties with low mass for efficient fixture changes. Order the part directly via Metav Werkzeuge or consult the team for application advice. Vertex 1347MA Clamping Screw – M14x2P thread, 175 mm A 1347MA clamping screw designed for secure fixture and repeatable clamping in jigs, fixtures and machine setups. Heat-treated steel construction M14x2P precision thread 175 mm overall length Lightweight at 0.18 kg Secure clamping with measurable repeatability The clamping element is manufactured from heat-treated steel, a process that increases surface hardness and wear resistance for repeated tightening cycles. The M14x2P precision thread gives consistent axial force per turn, which translates to reproducible clamp tension and reduced setup variation. For production environments where fixture downtime and part slippage must be minimised, this component delivers the mechanical stability expected in industrial clamping applications. Simple integration into standard fixturing systems With an industry-standard M14x2P thread and an overall length of 175 mm, the screw is compatible with common clamping plates and bespoke fixtures used in metalworking and assembly lines. Its nominal mass of 0.18 kg reduces inertia during manual handling and makes repeated adjustments less fatiguing for operators. The component is therefore suitable for retrofit tasks as well as new fixture designs, enabling straightforward integration without extensive redesign. Low-maintenance performance explained Heat treatment provides the core advantage: improved hardness and fatigue resistance without the need for complex coatings. That results in a component that maintains precision under cyclical loads and resists premature wear. Regular inspection of thread condition and lubrication where appropriate will sustain service life; no specialised maintenance procedures are required beyond standard workshop practices. Efficiency gains for workshop productivity Using a consistently manufactured clamping fastener reduces setup time and scrap risk, improving throughput and lowering per-part labour costs. The combination of durability and repeatable clamping behaviour supports tighter process control and fewer quality deviations. For operations aiming to standardise tooling across multiple workstations, this element contributes to predictable cycle times and simplified spare-part inventories. For specification checks, delivery from stock or application guidance contact Metav Werkzeuge in Emmerich: eMail info@metav-werkzeuge.com | Phone +49 2822 7131930 | WhatsApp +49 170 2837271 — Metav’s specialists will advise on the Vertex 1347MA and suitable fixture solutions Technical Data Article number: 1347MA GTIN: 4061905092787 Manufacturer: Vertex Key Figures Thread: M14x2P Length: 175 mm Weight: 0.18 kg Materials & Features Material: Heat-treated steel Application: Clamping / fixture use Brand: Vertex FAQ What is the main material of this clamping screw? The clamping screw is made from heat-treated steel, providing increased hardness and wear resistance for repeated use. Which thread standard does the part use? The part features an M14x2P precision thread, suitable for common clamping plates and fixtures. Is the 1347MA suitable for retrofit into existing fixtures? Yes, the 1347MA clamping screw from Vertex is compatible with standard fixturing systems and can be integrated without extensive redesign. Manufacturer: Vertex Machinery Works Co., Ltd.; No. 296, Sec. 1, Feng Shih Road, Fengyuan District, Taichung City 420, Taiwan
175mm Clamping Screw M16x2P Heat-Treated Steel, 0.23kg - Vertex
Take advantage of reliable clamping with heat-treated steel, a standard M16 x 2 thread and a 175 mm length that delivers robust fixture retention; order the component directly via Metav Werkzeuge or consult our advisors for integration details. Clamping Screw 1357M – Heat-treated steel, M16 x 2 thread (Vertex) The Clamping Screw 1357M is a heavy-duty clamping bolt designed for secure fixture and jig fastening in workshop and industrial settings Robust heat-treated steel construction Standard M16 x 2 metric thread Length 175 mm for deep clamping Precise fastening with 0.23 kg mass Durable steel construction for long service life The clamping screw is manufactured from heat-treated steel, a process that increases hardness and fatigue resistance so that fixtures maintain clamping force over many cycles. This material treatment reduces wear on the thread and seating faces, which translates into fewer replacements and lower downtime. For production environments where repeatable holding force matters, the treated-steel design supports consistent performance without frequent maintenance. Standard thread and dimensions for straightforward integration Equipped with a M16 x 2 metric thread and a 175 mm overall length, the fastener integrates easily with standard tapped holes and threaded clamping elements. The use of a common thread standard simplifies inventory and ensures compatibility with existing clamping systems and tooling plates. The clearly defined dimensions facilitate planning for toolroom layouts and guarantee predictable clamping reach for deeper workpieces. Stable clamping behaviour and handling benefits The component’s engineered geometry promotes consistent clamping and reliable axial alignment when seated, which helps prevent movement during machining or assembly operations. At 0.23 kg, the part is manageable during setup yet substantial enough to provide the required mechanical stability. The result is improved process reliability and fewer rechecks, supporting smoother workflows in jigs, fixtures and mechanical assemblies. Contact Metav Werkzeuge for purchasing advice on the Vertex clamping screw 1357M and secure supply from our Emmerich quality hub — email info@metav-werkzeuge.com or call +49 2822 7131930 Technical data SKU: 1357M GTIN: 4061905088070 Manufacturer: Vertex Facts Length: 175 mm Weight: 0.23 kg Thread: M16 x 2 Materials and features Product type: Clamping screw Material: Heat-treated steel ECLASS: 21022190 FAQ What thread does the clamping screw use and is it standard? The clamping screw uses a M16 x 2 metric thread, a standard pitch and diameter that is compatible with common tapped holes and clamping components. Is the component suitable for machine tooling and jigs? Yes, the design and heat-treated steel construction make the fastener suitable for use in jigs, fixtures and other clamping applications where repeatable holding force is required. How long is the clamping screw and what reach does it provide? The overall length is 175 mm, providing extended reach for deeper clamping tasks and allowing secure engagement with recessed or thick workpieces. What is the manufacturer and how is product quality assured? The part is supplied by Vertex and carries the SKU 1357M; Vertex production standards and Metav’s distribution in Emmerich act as a quality filter for the European market. Manufacturer: Vertex Machinery Works Co., Ltd.; No. 296, Sec. 1, Feng Shih Road, Fengyuan District, Taichung City 420, Taiwan
175mm Clamping Screw M18x2.5P Heat-Treated Steel, 0.3kg - Vertex
Compact, heat-treated steel construction combined with a M18×2.5 thread and a 175 mm length delivers secure, repeatable clamping where stable fixture engagement is required. Order the clamping screw directly via Metav Werkzeuge or consult our specialists for selection assistance. 1367M clamping screw — M18×2.5 thread, 175 mm (Vertex) A 1367M clamping screw engineered for reliable fixture and adjustment in machine tooling and industrial fixturing. Heat-treated steel for high durability M18 x 2.5 thread for standardised mounting 175 mm length for deeper engagement Precision-machined for consistent clamping Consistent clamping that keeps production running The combination of heat-treated steel and a standard metric thread ensures a robust connection between components and fixtures. The M18×2.5 specification provides compatibility with common clamping systems, reducing the need for adapters or bespoke fittings. Because the fastener is designed for repeatable engagement, cycle‑to‑cycle variation is minimised, which supports stable machining tolerances and fewer reworks — a practical advantage for workshop and production environments seeking steady throughput. Fast integration into existing tooling and fixtures Standardised dimensions simplify assembly and shorten setup times on jigs, fixtures and machine tables. The 175 mm overall length gives a longer engagement range for deeper clamps or thicker workpieces, while the metric thread pitch enables predictable torque settings and secure locking. These characteristics translate into straightforward installation and consistent results across batches, helping to maintain process reliability and reduce unplanned downtime in manufacturing operations. Durability-focused design to reduce maintenance intervals Manufactured from heat-treated steel, the screw is intended to withstand the mechanical stress typical in industrial clamping applications. This material choice contributes to a longer service life and stable clamping force over repeated cycles, which in turn lowers the frequency of replacements and maintenance interventions. When combined with good workshop practice, the part supports efficient maintenance schedules and contributes to overall equipment effectiveness. Contact Metav Werkzeuge for tailored advice on integrating Vertex clamping components into jigs and fixtures — call +49 2822 7131930 or email info@metav-werkzeuge.com Technical data Article number: 1367M GTIN: 4061905091544 ECLASS: 21022190 Facts Length: 175 mm Thread: M18 x 2.5 pitch Weight: 0.3 kg Special features Material: Heat-treated steel Manufacturer: Vertex FAQ What thread specification does the clamping screw use? The clamping screw is supplied with an M18×2.5 metric thread, matching common industrial fixtures. What is the main material and its benefit? The 1367M is made from heat-treated steel, offering increased wear resistance and extended service life under repetitive clamping loads. For which applications is this clamping screw suitable? The screw is intended for machine tooling, jig and fixture assembly, and other industrial fixturing tasks where secure, repeatable clamping is required. What are the length and weight of the component? The component measures 175 mm in length and has a weight of 0.3 kg, suitable for deeper engagement scenarios without excessive mass. Manufacturer: Vertex Machinery Works Co., Ltd.; No. 296, Sec. 1, Feng Shih Road, Fengyuan District, Taichung City 420, Taiwan
175mm Clamping Screw M20x2.5P Heat-Treated Steel, 0.35kg - Vertex
Take advantage of a robust combination of heat-treated steel construction, a precise M20 x 2.5 thread and a 175 mm engagement length to ensure reliable clamping in production fixtures; order the clamping screw directly via Metav Werkzeuge or ask our consultants if needed. Clamping screw – M20 x 2.5 thread, 175 mm, Vertex The clamping screw is a heavy-duty fastening component for fixture and jig applications, designed to deliver consistent axial clamping force in industrial and workshop environments. Heat-treated steel construction Metric thread M20 x 2.5 175 mm length for secure engagement Built for consistent clamping performance The robust design of this fastening element provides steady clamping reliability under repeated load cycles. Manufactured from heat-treated steel, the component maintains shape and preload resilience even when subjected to frequent tightening and release. For workshop planners and production engineers, this means fewer resets and less variability in jig setups, which supports predictable part quality and shorter adjustment times during batch runs. Precision thread and engagement that reduce setup time The M20 x 2.5 metric thread ensures accurate engagement with complementary nuts or threaded bores, translating to reliable axial positioning in assemblies. A defined 175 mm length gives deeper thread engagement where required, improving pull-out strength and reducing the need for additional reinforcement. Explaining the metric specification: the M20 dimension denotes the nominal diameter and 2.5 mm the thread pitch, which together govern compatibility with standardised clamping interfaces. Durability that lowers maintenance intervals Surface finish and material treatment influence lifetime performance. With heat-treated steel as the base material, the fastener resists deformation and wear during intensive use. This durability reduces unplanned maintenance and replacement frequency, supporting continuous production. Where environmental factors matter, selection of appropriate corrosion protection at the assembly stage will preserve function over time and protect system availability. Seamless integration into fixture systems Designed for clamping technology applications, this component integrates into existing workholding setups, modular clamping plates and bespoke jigs. The straightforward metric thread and standard length make it compatible with many industry-standard accessories and adaptors. For procurement departments wanting to consolidate suppliers, the fastener’s compatibility simplifies inventory while maintaining the performance required in precision tooling environments. Contact Metav Werkzeuge to discuss specification matching, delivery options from our Emmerich warehouse or technical advice for fitting the Vertex clamping screw 1377M into specific fixtures Technical data SKU: 1377M GTIN: 4061905088087 Manufacturer: Vertex Core data Material: Heat-treated steel Thread: M20 x 2.5 Length: 175 mm Weight: 0.35 kg Materials & compatibility Suitable for use in clamping technology and fixture assemblies Designed for standard metric-threaded connections Intended for repeated tightening cycles and industrial workshop use FAQ What is the primary application for this clamping screw? The clamping screw 1377M by Vertex is intended for fixture and jig clamping in industrial and workshop environments where repeated, reliable axial clamping is required. Which material is used for the fastener and what benefit does it bring? Manufactured from heat-treated steel, the Vertex clamping screw offers improved wear resistance and dimensional stability, reducing maintenance and preserving clamping performance. Is the thread compatible with standard nuts and threaded inserts? Yes, the M20 x 2.5 thread on the Vertex 1377M matches standard metric M20 fittings and is suitable for common threaded inserts and nuts used in clamping systems. Can this clamping screw be used in corrosive environments? The basic component is heat-treated steel; for corrosive conditions, application-specific surface protection or corrosion-resistant variants should be considered to extend service life. How does the 175 mm length affect fixture design? A 175 mm engagement length provides deeper thread contact and improved pull-out resistance, which is beneficial where stronger axial retention is needed in fixtures and jigs. Manufacturer: Vertex Machinery Works Co., Ltd.; No. 296, Sec. 1, Feng Shih Road, Fengyuan District, Taichung City 420, Taiwan
175mm Clamping Screw M8x1.25 Thread, Heat-Treated Steel - Vertex
Take advantage of a robust combination of heat-treated steel construction and a standard M8 x 1.25 thread to secure fixtures with consistent clamping force; the 175 mm length offers extended reach for deep setups. Order the clamping screw directly via Metav Werkzeuge or consult our specialists for application-specific advice. Clamping screw by Vertex — M8 x 1.25 thread, 175 mm, heat-treated steel A clamping screw engineered for dependable fixture retention in industrial and workshop clamping systems, suitable for standardised machine and workholding applications. Heat-treated steel construction for durability Standard M8 x 1.25 metric thread for wide compatibility 175 mm length for extended reach in fixtures Compact weight of 0.06 kg enables easy handling Consistent retention and wear resistance for production environments The combination of heat-treated steel and a calibrated metric thread provides a reliable hold that reduces the need for frequent replacement. Heat treatment increases hardness and wear resistance, which in turn preserves the clamping face and thread integrity under repeated loading cycles. The M8 x 1.25 thread is a widely used standard, facilitating straightforward replacement and compatibility with common tapped holes and nuts. For production lines and toolrooms, this means fewer stoppages for fastener failure and more predictable clamping behaviour during batch work. Easier integration into clamping systems and fixtures A standardised M8 x 1.25 profile and the 175 mm length make this fastener versatile for a range of fixturing tasks, from securing jigs to clamping larger workpieces where additional reach is required. The metric pitch ensures even load distribution along the thread, which helps maintain preload and prevents loosening under vibration. Where thread engagement depth is critical, the extended length affords flexibility in positioning without resorting to bespoke fasteners. This reduces setup complexity and supports faster changeovers between jobs. Traceability, workshop readiness and supply reliability Lightweight at 0.06 kg and supplied under SKU 1327M, the item is simple to store and quick to pick for routine maintenance or kitting. The manufacturer’s identification and GTIN provide clear traceability for quality control and procurement records. Sourcing through an experienced distributor ensures a consistent supply chain: Metav Werkzeuge acts as a quality filter for the European market, combining broad stock availability with specialist advice so workshops can rely on performance and delivery. This approach supports operational continuity and reduces the administrative burden of multi-supplier sourcing. For robust, standardised clamping in demanding workshop and industrial settings, contact Metav Werkzeuge for procurement and application guidance on the Vertex clamping screw — trusted performance, traceable supply from Emmerich. Technical data SKU: 1327M GTIN: 4061905091124 Eclass: 21022190 Core technical data Length: 175 mm Thread: M8 x 1.25 Weight: 0.06 kg Materials & features Material: heat-treated steel Thread form: metric coarse pitch Manufacturer: Vertex FAQ What thread size does this clamping screw use? The clamping screw is supplied with an M8 x 1.25 metric thread, matching common tapped holes and nuts for wide compatibility. Is the material suitable for frequent industrial use? Yes, the fastener is made from heat-treated steel, which increases hardness and wear resistance for repeated clamping cycles in workshop and production environments. What is the overall length and how does that affect application? The overall length is 175 mm, providing extended reach for deeper fixtures and flexible positioning in clamping systems. How can I identify the correct article when ordering? Order by SKU 1327M or the GTIN 4061905091124 to ensure the correct clamping screw from Vertex is supplied. Manufacturer: Vertex Machinery Works Co., Ltd.; No. 296, Sec. 1, Feng Shih Road, Fengyuan District, Taichung City 420, Taiwan
175mm Clamping Wedge for T‑Slot 20mm Height 0-85mm M20x20x200 - AMF
Reliable clamping for 20 mm T‑slots and an adjustable clamping height of 0–85 mm deliver secure workholding; the supplied M20 x 20 x 200 clamping screw simplifies setup and reduces changeover time. Order the component directly via Metav Werkzeuge or consult our advisers for specification support. Clamping bar Nr. 6321 — for 20 mm T‑slot, clamping height 0–85 mm (AMF) The Clamping bar Nr. 6321 is a robust clamp bar designed to secure fixtures and workpieces in 20 mm T‑slots, providing an adjustable clamping height from 0 to 85 mm for flexible machining setups. For 20 mm T‑slot Clamping height 0–85 mm Includes M20 x 20 x 200 clamping screw Length 175 mm, width 21 mm Faster, more reliable workholding for machining operations The combination of an adjustable clamping height 0–85 mm and compatibility with a 20 mm T‑slot translates directly into reduced setup times and steadier machining. The bar’s geometry and the supplied M20 x 20 x 200 clamping screw allow a single, repeatable clamping procedure that secures components evenly across the contact surface. For production environments where cycle time and repeatability matter, this design supports consistent results and fewer re-clamps during batch runs. Simple integration and versatile application across fixtures Designed for straightforward installation into standard machine tables and fixture plates, the bar fits the common 20 mm T‑slot and matches existing clamping arrays. The compact footprint—175 mm overall length and 21 mm width—permits close packing of multiple bars for complex fixturing, while the adjustable range gives flexibility for variable workpiece heights. This reduces the need for special adapting parts and streamlines tool planning in general workshop and industrial contexts. Durable build for dependable industrial performance Manufactured for repetitive use, the component supports stable clamping without excessive maintenance. The measured design minimises flex under load, helping to preserve machining accuracy over time. Where precision and safety are required, the robust construction contributes to fewer stoppages and consistent part quality, aligning with common shop-floor expectations for long-term reliability. For purchasing guidance on the AMF clamping solution and fast fulfilment from Emmerich, contact Metav Werkzeuge at info@metav-werkzeuge.com or +49 2822 7131930. Technical data Article number: 4000833069NW Type: Nr. 6321 Product type: Clamping bar Manufacturer: AMF Packaging unit: 1 Dimensions / Core specifications Width: 21 mm Overall length: 175 mm Clamping height: 0–85 mm T‑slot compatibility: 20 mm Features / Accessories Included clamping screw: M20 x 20 x 200; B2: 60 Suitable for standard machine tables and fixture plates Compact design for dense fixturing FAQ What T‑slot size does this clamping bar fit? The clamping bar fits a 20 mm T‑slot; compatibility is specified for standard 20 mm table slots. What is the adjustable clamping height range? The clamping height ranges from 0 to 85 mm, enabling a wide variety of workpiece thicknesses to be secured. Is the clamping screw included with the unit? Yes, the delivery includes an M20 x 20 x 200 clamping screw as stated in the product details for the AMF clamping bar (SKU 4000833069NW). Can multiple bars be used together on a table? The compact 21 mm width and 175 mm length allow several bars to be mounted closely for multi-point fixturing and complex workholding arrangements. Manufacturer: AMF / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
175mm Magnetic Chip Collector With Shield, 390mm Overall Length - TECWERK
Take advantage of a compact, shielded magnetic collector that secures ferrous swarf with a 175 mm magnet surface and clears chips instantly via a pull‑out pin in the handle — ideal for keeping machines running and maintenance brief. Order this tool directly through Metav Werkzeuge or consult our specialists for application advice. Chip collector, magnetic (magnet surface 175 mm, total length 390 mm) – TECWERK The Chip collector, magnetic (magnet surface 175 mm, total length 390 mm) is a shielded, magnetic swarf collector designed for efficient removal of ferrous debris from machines, workbenches and confined areas Magnetic with protective shield Attracts all ferrous swarf Quick release via pull-out pin Magnet surface length 175 mm Efficient ferrous swarf collection for machine shops The TECWERK chip collector combines a magnetic bar with a protective shield to capture and retain metallic chips where they are generated. The 175 mm magnet surface provides an extended active area that concentrates magnetic force across a useful span, enabling rapid collection of filings, turnings and loose iron particulates. For production environments this translates into fewer stoppages for manual cleaning and a lower risk of stray ferrous debris causing tool damage or quality issues. The term ferrous refers to materials that contain iron and are therefore attracted to a magnet, which explains why non‑magnetic alloys and most stainless grades are not captured by this device. Rapid, safe clearing that reduces maintenance time A purposeful pull‑out pin in the handle releases accumulated swarf in a single motion: by withdrawing the pin the magnetic bar lets go and the collected chips fall away into a bin or tray. This mechanism eliminates fiddly scraping and avoids contact with sharp turnings, improving operator safety and shortening cleaning cycles. The simple mechanical action requires no power and minimal training, delivering a reliable time saving per shift that adds up across the workshop. Robust, compact design for everyday industrial use The shielded construction protects the magnet from heavy contamination while providing a compact footprint for use on lathes, CNC machines and under benches. The stated total length of 390 mm balances reach and manoeuvrability, making the tool suitable for tight spaces as well as routine bench work. Built for repetitive use, the collector’s materials and finish support durability in regular industrial settings, ensuring a consistent magnetic performance and prolonged service life with straightforward handling. For reliable ferrous swarf handling choose the TECWERK magnetic chip collector and contact Metav Werkzeuge in Emmerich for procurement or tailored technical advice via info@metav-werkzeuge.com or +49 2822 7131930 Technical Data Article number: 4000832992NW Product type: Chip collector Execution: magnetic with protective shield Packaging unit: 1 Specifications Magnet surface length: 175 mm Total length: 390 mm SKU: 4000832992NW Features Magnetised bar with protective shield Attracts magnetic (ferrous) materials Quick‑release via pull‑out pin in handle Compact design for machine and bench use FAQ How does the magnetic collector remove chips? The collector uses a magnetic bar to attract ferrous swarf; by pulling the handle pin the magnet releases and the chips fall off for disposal. Is the tool suitable for stainless steel filings? Only magnetic grades are captured; stainless types that are non‑magnetic will not be attracted by the magnetic collector. What is the active magnetic length? The magnet surface measures 175 mm, offering a broad collection area for efficient clearing. Can the collector be used on a lathe or mill? Yes, the compact, shielded design makes the collector suitable for use at lathes, milling machines and workbenches to keep work areas clear. How is debris disposed of after collection? Debris is released by withdrawing the pull‑out pin; the collected swarf drops into a bin or tray for straightforward disposal. Manufacturer/Responsible: NORDWEST Handel AG, Robert‑Schuman‑Straße 17, 44263 Dortmund
175mm Verlängerungshülse Morsekegel gehärtet geschliffen, DIN 2187 - TECWERK
Verlängerungshülse DIN 2187 MK2xMK2 geh.u.geschl.TECWERK Verlängerungshülse DIN 2187 MK2xMK2 geh.u.geschl.TECWERK für präzise Werkzeugverlängerung bei Dreharbeiten und Bohrapplikationen in Zerspanungsbetrieben Norm DIN 2187 Genauigkeitsausführung Gehärtet und innen sowie außen geschliffen Passend für Morsekegel MK2 (Morsekegel Nr. 2) Durchmesser D 30 mm für stabile Aufnahme Gesamtlänge 175 mm für erhöhte Reichweite Präzision und Materialvorteile für stabile Ergebnisse Die Verlängerungshülse überzeugt durch ihre Genauigkeitsausführung nach DIN 2187, wodurch Rundlauf und Werkzeugposition sicher eingehalten werden. Die Hülse ist gehärtet und innen und außen geschliffen, was Verschleiß reduziert und die Lebensdauer erhöht. Die D 30 mm Aufnahme sorgt für formstabile Verbindung zwischen Maschine und Werkzeug, sodass empfindliche Bearbeitungsprozesse mit hoher Wiederholgenauigkeit ausgeführt werden können. Kompatibilität und Einsatz in der Werkstatt Diese Verlängerungshülse ist für Werkzeuge mit Morsekegel ausgelegt und nutzt sowohl Innenkegel MK2 als auch Außenkegel MK2, wodurch sie sich nahtlos in bestehende Werkzeugaufnahmen einfügt. Mit einer Gesamtlänge 175 mm und den Längenangaben L1 100 mm sowie L2 175 mm eignet sich die Hülse für verlängerte Bohrungen, schwer zugängliche Werkstücke und Vorrichtungen, in denen zusätzliche Reichweite ohne Einbußen bei der Präzision gefordert ist. Wirtschaftlichkeit, Handhabung und Sicherheit am Arbeitsplatz Der Einsatz der TECWERK Verlängerungshülse reduziert Rüstzeiten, weil standardisierte Maße und die Genauigkeitsausführung einen schnellen, wiederholbaren Werkzeugwechsel ermöglichen. Die gehärteten und geschliffenen Oberflächen verringern das Risiko von Wackeln und ungleichmäßigem Verschleiß, was Folgekosten minimiert. Anwender profitieren von einer robusten Lösung, die in Serienfertigung und Einzelteilbearbeitung gleichermaßen zuverlässige Ergebnisse liefert. Empfehlung: Für präzise Verlängerungen in der Zerspanung empfiehlt sich die Kombination der TECWERK Verlängerungshülse mit original Morsekegel-Werkzeugen; Bei technischen Fragen gern per eMail an info@metav-werkzeuge.com oder telefonisch unter +49 2822 7131930 Produktmerkmale Artikelnummer: 2000832320NW Marke: TECWERK Norm: DIN 2187 Produktart: Verlängerungshülse Innenkegel: MK2 Aussenkegel: MK2 Daten D: 30 mm L2: 175 mm L1: 100 mm Gesamtlänge: 175 mm Besonderheiten Gehärtet und geschliffen Genauigkeitsausführung Für Werkzeuge mit Morsekegel (MK2 = Morsekegel Nr. 2) Verpackungseinheit: 1 SKU: 2000832320NW FAQ Für welche Werkzeugaufnahme ist die Hülse geeignet? Die Verlängerungshülse von TECWERK ist für Werkzeugaufnahmen mit Morsekegel ausgelegt und verwendet Innenkegel MK2 sowie Außenkegel MK2, dadurch passt sie zu gängigen Dreh- und Bohrvorrichtungen. Welche Vorteile bringt die Genauigkeitsausführung nach DIN 2187? Die Genauigkeitsausführung sorgt für verbesserten Rundlauf und gleichbleibende Positionierung, was bei Serienfertigung und Präzisionsarbeiten mit der TECWERK Verlängerungshülse zu konstanteren Ergebnissen führt. Wie wirkt sich die gehärtete und geschliffene Oberfläche aus? Gehärtete und geschliffene Oberflächen vermindern Verschleiß, erhöhen die Standzeit und erhalten die Passgenauigkeit, sodass die Hülse länger präzise einsetzbar bleibt. Welche Abmessungen sind relevant für die Auswahl? Wesentliche Maße sind D 30 mm, L1 100 mm, L2 175 mm und die Gesamtlänge 175 mm; diese Angaben helfen bei der Integration in Spannsysteme und bei der Planung der Bearbeitungsreichweite. Hersteller: NORDWEST Handel AG; Robert-Schuman-Straße 17; 44263 Dortmund
175x100 Cross Table Mini Precision, 68.5mm Height - SAIM
Take advantage of a compact, measurement-ready cross-slide stage that combines a 175 x 100 mm work platform with a low profile of 68.5 mm for easy integration on benches and small machines; its modest mass supports stable setups with minimal footprint. Order the SAIM-175XG Mini Cross Table directly via Metav Werkzeuge or consult our specialists for application advice. SAIM-175XG Mini Cross Table – compact 175 x 100 mm platform, 68.5 mm height A SAIM-175XG mini cross-slide table designed for precise small-part positioning and repeatable XY adjustment in workshop and inspection applications. Compact cross-slide table for small workpieces Table area 175 x 100 mm Overall height 68.5 mm Weight 7 kg Precise positioning in a compact footprint The mini cross-slide is engineered as a cross-slide table that delivers controlled lateral adjustment without occupying valuable bench space. The 175 x 100 mm platform provides a defined work area for fixtures and small components, while the 68.5 mm profile enables mounting under low-clearance setups. The mechanical guidance is intended to improve setup repeatability and shorten alignment time, so task cycles become more predictable. This combination of compact dimensions and deliberate engineering supports accurate fixturing for measuring, marking and light machining operations. Easy integration and measurable benefits Integration is simplified by the table’s small footprint and modest mass of 7 kg, which reduces the need for heavy support structures and makes relocation straightforward. A cross-slide stage like this one reduces the number of manual repositioning steps, increasing throughput and decreasing cumulative positioning error. The clear numeric specifications—platform size, height and weight—make planning and machine interfacing transparent: these measurable values enable correct fixture design and predictable process planning, delivering a tangible improvement in operational efficiency. Typical applications and who gains most This mini cross-slide is suitable for inspection benches, light milling or drilling jigs, and precision assembly stations where space is limited but positional control remains critical. Shop floor technicians, inspection engineers and bench machinists benefit from the compact positioning stage format when handling small series or prototyping. The product supports workflows that prioritise repeatable alignment over heavy-duty cutting, making it a practical addition to labs and workshops aiming to centralise precision operations without major machine modifications. Practical notes on use and setup When planning an installation, consider the platform dimensions and overall height for clamp and fixture clearance; the compact design facilitates direct mounting on measuring tables or workbenches. If repeatability requirements are high, combine the stage with stable fixturing and follow-up checks to confirm alignment. For bespoke integration scenarios, Metav’s technical advisors can propose suitable mounting strategies and ancillary parts to achieve the required positioning performance. Contact Metav Werkzeuge today to discuss the SAIM-175XG mini cross slide for precise small-part positioning and to receive tailored technical advice and delivery options from our Emmerich team Technical data Article number: SAIM-175XG GTIN: 4061905082535 Manufacturer: SAIM eClass: 21041714 Thumbnail: https://files.plytix.com/api/v1.1/file/public_files/pim/assets/57/c3/98/62/6298c3575d155f1bc7e497fd/images/0d/af/6b/63/636baf0d5ba163a434b93e44/saim-150x-xg-modelle.jpg Facts Table dimensions: 175 x 100 mm Height: 68.5 mm Weight: 7 kg Special features Compact cross-slide table format Suitable for inspection, light milling and assembly Includes technical drawing and model overview images FAQ What are the main dimensions of the stage? The SAIM-175XG has a platform of 175 x 100 mm and an overall height of 68.5 mm, enabling compact integration on benches and small machines. Is the cross-slide suitable for machining as well as inspection? The mini cross-slide is designed primarily for positioning, inspection and light machining tasks where controlled XY movement and a small footprint are required. How heavy is the SAIM-175XG and does it require special support? The stage weighs 7 kg, which generally allows stable placement on standard benches or measuring tables without heavy additional supports. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
175x100 Cross Table Mini Precision, 75mm Height - SAIM
A compact cross-slide table with a 175 x 100 mm platform and a low 75 mm profile provides precise positioning in limited spaces while the 8 kg mass improves stability. Order the SAIM mini cross-slide table directly via Metav Werkzeuge or consult our advisors for application guidance. SAIM Mini Cross-slide Table — compact 175 x 100 mm platform, 75 mm low profile SAIM Mini Cross-slide Table is a compact XY positioning stage designed for small workspaces and precision jigs; ideal as a reliable base for fine adjustment and inspection tasks. Compact 175 x 100 mm platform Low 75 mm profile for tight setups Stable 8 kg base for vibration damping Space-saving design that keeps production flexible The compact footprint of this mini cross-slide table makes it suitable where bench space is limited. The 175 x 100 mm platform offers a clearly defined working area for fixtures and small components, while the 75 mm overall height keeps the centre of gravity low. This configuration enables efficient integration into inspection benches or small machining centres, helping to reduce repositioning time and maintain a continuous workflow. The small form factor supports modular layouts and saves valuable bench space without compromising usability. Stable mass for improved positioning reliability With a mass of 8 kg, the stage delivers a stable base that dampens minor vibrations and supports steady manual adjustments. Stability contributes directly to repeatable results during measurement and light machining tasks. Where small displacements matter, the extra mass of the unit helps to reduce chatter and unwanted movement, which in turn improves the quality of alignment and repeatability of processes that rely on precise XY positioning. Practical uses and workshop compatibility The unit functions well as a compact positioning table in assembly, inspection, prototyping and light tooling applications. As a basic XY stage, it facilitates fine lateral and longitudinal adjustment of small components and jigs. The simple geometry of the mini XY stage also makes it straightforward to combine with clamping fixtures or small rotary stages for expanded functionality, providing a practical solution for labs and workshops that require adaptable, space-conscious positioning aids. Contact Metav Werkzeuge today to discuss how the SAIM mini cross-slide table with its 175 x 100 mm platform and 75 mm low profile can be integrated into existing workflows or bespoke fixtures Technical data Article number: SAIM-175XY GTIN: 4061905082528 Brand: SAIM Platform dimensions: 175 x 100 mm Height: 75 mm Weight: 8 kg Facts Platform area: 175 x 100 mm Low profile height: 75 mm Mass: 8 kg SKU: SAIM-175XY GTIN: 4061905082528 Special features Mini cross-slide table design Compact footprint for bench-top use Suitable for precision positioning tasks FAQ What are the exact platform dimensions of the stage? The platform measures 175 x 100 mm, giving a clearly defined working area for small fixtures and components on the SAIM mini cross-slide table. How tall is the unit and why does that matter? The overall height is 75 mm; the low profile helps keep the centre of gravity down and simplifies integration into confined setups or stacked tool arrangements. Is the stage heavy enough to reduce vibration during adjustments? At 8 kg, the stage provides a stable base that helps dampen minor vibrations and supports consistent manual positioning for small-scale tasks. Can this table be combined with other fixtures or stages? The compact geometry of the mini cross-slide table permits straightforward integration with small clamping fixtures or rotary stages to extend functionality in assembly and inspection setups. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
175x100 Cross Table Mini, 50.5mm Height - SAIM
Compact cross-slide precision in a small footprint — the combination of a 175 x 100 mm tabletop, a low 50.5 mm profile and a sturdy 5 kg chassis delivers stable positioning and easy integration for light workshop and inspection tasks. Order the SAIM-175X Mini cross slide table directly via Metav Werkzeuge or ask the consultants for application advice. SAIM-175X Mini cross slide table — compact 175 x 100 mm top, 50.5 mm height SAIM-175X is a compact cross slide table designed for precise positioning and small-part machining in confined workspaces, suitable for toolmaking, inspection benches and light assembly jigs. Mini cross slide table 175 x 100 mm top Low-profile height 50.5 mm Robust 5 kg construction Precise positioning for small fixtures Fit precise work into tight spaces with confidence The compact design of this cross slide provides a stable working surface while occupying minimal bench area. With a top size of 175 x 100 mm and a low 50.5 mm profile, the table is tailored to applications where space is limited but precision is still required. The reduced height helps integrate the unit beneath inspection optics and within multi-axis set-ups, enabling accurate alignment without raising the workpiece unnecessarily. Achieve repeatable positioning for efficient workflows A stable platform and fine movement control translate into repeatable set-ups and fewer adjustment cycles during production or assembly. The unit’s mass of 5 kg contributes to vibration damping and a firmer support for small tools and measuring devices. For workshop processes that prioritise consistent results over long runs, the cross slide supports efficient task sequences and reduces unnecessary handling of delicate components. Versatile companion for metrology and light machining Engineered for workshop and metrology contexts, the cross slide is compatible with a range of small-scale operations such as fixture mounting, component inspection and delicate drilling or milling set-ups. The compact cross slide table serves as a practical addition to inspection benches, small lathes and toolmaking stands, providing a precise, adjustable base for repeatable measurement and machining tasks. Clear documentation and visual references for simple integration Technical drawings and product images are supplied to simplify mounting and integration into existing workflows. The available drawings help clarify dimensions and mounting clearances so that integration with fixtures, clamps or measuring equipment can be planned without guesswork. This visual documentation ensures predictable installation and supports long-term, reliable use. Contact Metav Werkzeuge GmbH in Emmerich for specific application advice and availability of the SAIM-175X mini cross slide table; phone +49 2822 7131930 or eMail info@metav-werkzeuge.com Technical data Article number: SAIM-175X GTIN: 4061905082511 Label: Kreuztisch Mini Manufacturer: SAIM Weight: 5 kg Top dimensions: 175 x 100 mm Height: 50.5 mm eClass: 21041714 Measurements Top: 175 x 100 mm Height: 50.5 mm Weight: 5 kg GTIN: 4061905082511 Features Brand: SAIM Model type: Mini cross slide table Includes technical drawing and product images Compact footprint for bench and inspection use FAQ What is the tabletop size of the cross slide? The tabletop measures 175 x 100 mm, providing a compact working surface suitable for small fixtures and components on the SAIM-175X. What is the overall height of the unit? The cross slide has a low profile with a height of 50.5 mm, allowing integration under inspection optics and in confined setups. How heavy is the cross slide table? The SAIM-175X weighs 5 kg, which contributes to stability and helps reduce vibration during positioning and light machining tasks. Are technical drawings available for planning the installation? Technical drawings and product images are supplied to assist with mounting and integration planning for the SAIM-175X. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
175x100mm Cross Table Mini Precision Travel, 93mm Height - SAIM
Compact, reliable positioning for small machines and inspection benches is delivered by the combination of a 175 x 100 mm table, a low 93 mm height and a solid mass for steady operation; benefit from precise two‑axis control and a small footprint for streamlined workflows — order via Metav Werkzeuge or consult the technical team for application advice. SAIM-175XYG Mini cross table — compact XY stage with 175 x 100 mm tabletop The SAIM-175XYG is a compact mini cross table designed for precise two‑axis positioning in tight workshop and inspection environments. Compact table 175 x 100 mm Precise two‑axis positioning Stable 9 kg mass for vibration damping Compact 93 mm installation height Space-saving precision for tight setups A compact footprint combined with precise linear movement makes this mini cross table suitable where bench space is limited. The 175 x 100 mm table area allows secure clamping of small workpieces or fixtures while the 93 mm height keeps the assembly close to the machine spindle or measuring system, reducing overhang and improving control. The result is a smaller setup envelope and a more efficient use of bench or machine table space, which supports higher throughput in confined production and quality‑control cells. Reliable positioning that improves process quality The construction and mass — approximately 9 kg — provide stability that reduces chatter and improves repeatable placement. For tasks that demand controlled incremental adjustment, the stage enables consistent positioning, which in turn supports accurate machining, drilling guidance and metrology checks. Where reproducible alignment is required, the device’s steady behaviour helps to lower scrap rates and shorten rework cycles, offering a measurable benefit to productivity. Integration and versatility for workshop applications The unit is intended as a flexible positioning aid for small milling, drilling and inspection tasks. As an XY stage, the cross slide table simplifies the alignment of parts for measurement or secondary operations and can be used as a fixed platform for jigs and small fixtures. Its compact dimensions and modest mass mean the component is straightforward to install into existing workflows, enabling rapid changeovers and straightforward retrofitting without the need for large machine modifications. Built for steady performance and easy handling Manufacturing and inspection routines benefit from a device that is easy to incorporate and maintain. The simple form factor reduces potential failure modes and keeps maintenance predictable. Clear, measurable data such as the tabletop size, installation height and mass provide a transparent basis for planning machine integration or workstation layout, which supports risk‑aware purchasing decisions and long‑term process stability. For tailored advice on integrating the SAIM-175XYG mini cross table into existing setups or to check current availability, contact Metav Werkzeuge for individual consultation at info@metav-werkzeuge.com or +49 2822 7131930. Technical data Article number: SAIM-175XYG GTIN: 4061905082542 ECLASS: 21041714 Core data Table dimensions (L x W): 175 x 100 mm Height: 93 mm Weight: 9 kg Features Type: Mini cross table Manufacturer: SAIM SKU: SAIM-175XYG Files: saim-150x-technische-zeichnung.jpg, saim-150x-xyg-modelle.jpg FAQ What are the physical dimensions of the table? The tabletop measures 175 x 100 mm and the installation height is 93 mm; the unit weight is 9 kg for the SAIM-175XYG mini cross table. Is this cross table suitable for precise positioning tasks? Yes, the SAIM-175XYG is designed as an XY stage for controlled two‑axis positioning, offering the stability and repeatability required for small‑scale machining and inspection operations. Which applications are typical for this mini cross table? Common uses include small milling and drilling guidance, fixture mounting for inspection, and fine alignment tasks in assembly and metrology stations with limited space. How does the weight affect performance? The approximately 9 kg mass of the SAIM-175XYG improves vibration damping and stability, which supports more consistent positioning and better surface finishes on light machining tasks. What identifiers should be used when ordering or referencing this item? Reference the article number SAIM-175XYG and GTIN 4061905082542 when enquiring or ordering. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
175x240x118mm Modular Machine Vice Modular Design, 0.01mm Accuracy - Vertex
Take advantage of the modular clamping concept and 0.01 mm repeatability to increase process reliability while keeping set-up times low; order the unit directly via Metav Werkzeuge or consult our specialists for application-specific guidance. Vertex VMP-77D modular machine vice — high-precision 0.01 mm repeatability, compact footprint The VMP-77D modular machine vice is a precision clamping solution designed for machining environments, combining a flexible modular concept with a compact body for stable workholding on milling machines and machining centres. Modular clamping concept 0.01 mm repeatability Robust 42.4 kg construction Compact 175×240×118 mm footprint Consistent accuracy for repeatable machining The vice delivers repeatable clamping at 0.01 mm, which reduces variation across batches and minimises rework. The precise tolerance control provided by the design translates into stable cutting conditions and a predictable surface finish, allowing reliable batch production. The emphasis on precision supports quality assurance procedures and simplifies integration into inspection routines. Stable, modular construction that adapts to the task A modular approach offers flexibility for varied fixturing requirements while the substantial mass contributes to vibration damping and firm clamping. The compact footprint of the unit helps save table space without compromising rigidity, enabling more efficient use of machine bed area. This combination of adaptability and robustness supports quicker set-ups and repeatable results in mixed-production environments. Practical operation and procurement confidence The vice’s form factor and construction favour straightforward handling and integration into existing workflows. Procurement through Metav Werkzeuge provides the additional assurance of a European quality filter and dependable logistics from Emmerich, backed by long-term experience in precision tooling. The pairing of a proven clamping concept with reliable supply reduces sourcing complexity for workshops and production facilities. For tailored advice on implementing Vertex modular clamping solutions, contact Metav Werkzeuge for application guidance and reliable supply from our Emmerich hub — email info@metav-werkzeuge.com or call +49 2822 7131930 Technical Data Article number: VMP-77D GTIN: 4061905091209 Manufacturer: Vertex Machinery Works Co., Ltd. eClass: 21020601 ETIM: EC002173 Facts Accuracy: 0.01 mm Weight: 42.4 kg Dimensions: 175 x 240 x 118 mm Special features Modular design for flexible fixturing Type: Modular Category: Vertex FAQ What level of precision can be expected from this vice? The VMP-77D from Vertex provides repeatable clamping accuracy of 0.01 mm, suitable for precision machining and tight tolerance work. Is the vice suitable for use on milling machines and machining centres? Yes, the modular machine vice is designed for machining environments and integrates on typical milling machine tables and machining centres. How does the modular design benefit workshop workflows? Modularity allows flexible fixturing and faster reconfiguration, enabling the vice to adapt to different parts and reducing set-up times on the shop floor. What are the physical dimensions and weight of the unit? The vice measures 175 x 240 x 118 mm and weighs 42.4 kg, providing a compact yet stable footprint for machine tables. Who manufactures the VMP-77D and where is it sourced from? The VMP-77D is manufactured by Vertex; supply and distribution can be arranged via Metav Werkzeuge for European customers. Manufacturer: Vertex Machinery Works Co., Ltd.; No. 296, Sec. 1, Feng Shih Road, Fengyuan District, Taichung City 420, Taiwan
175x240x118mm Modular Machine Vice, 0.01mm Accuracy, 42.4kg - Vertex
Take advantage of a modular approach to heavy-duty workholding and the proven 0.01 mm repeatability for consistent batch results; combine these attributes with the vice’s inherent mass for reduced vibration and steady cuts. Order the unit directly via Metav Werkzeuge or consult our specialists for application-specific configuration. VMP-7L Modular machine vice by Vertex — 0.01 mm accuracy, compact footprint The VMP-7L is a modular machine vice designed for secure workholding in milling centres and general machining applications, offering precise clamping and flexible configuration. Modular configuration for flexible set-ups High precision with 0.01 mm repeatability Solid mass ensures vibration damping Precision that reduces rework and increases throughput The modular workholding system delivers a high level of precision, with verified 0.01 mm repeatability that supports tight tolerances on serial production runs. The vice’s design focuses on minimising movement between clamping cycles, which translates into fewer scrapped parts and less rework. For operators and engineers seeking measurable efficiency gains, the combination of dependable repeatability and a compact footprint makes this solution suitable for small-batch jobs as well as repetitive machining tasks, where consistent part geometry is essential. Flexible modularity for changing production demands A modular design enables rapid reconfiguration of the vice to match different component geometries and clamping strategies without the need for multiple fixed vices. The adaptable layout reduces set-up times and supports a greater variety of workpieces from the same clamping base. The unit’s substantial mass contributes to stable machining conditions, improving surface finish and tool life by dampening vibrations during cutting operations. Clear dimensional data facilitates integration into existing fixtures and machine tables. Reliable supply and service from a trusted partner Metav combines long-standing sector expertise with a broad stock range, ensuring access to compatible components and replacement parts when required. The distribution hub in Emmerich acts as a quality filter for the European market, supporting dependable delivery and a simplified procurement process. For procurement managers and workshop leads, the documented performance and the supplier’s track record reduce uncertainty, making this vice a pragmatic choice for enhancing workshop capability and maintaining production continuity. Contact Metav Werkzeuge for tailored advice on the Vertex VMP-7L modular machine vice and to discuss configuration options — eMail info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: VMP-7L GTIN: 4061905094347 Manufacturer: Vertex Type: Modular Key figures Dimensions: 175x240x118 mm Accuracy: 0.01 mm Weight: 42.4 kg Features Modular design Compact footprint for machine table integration Built for stable clamping and vibration damping FAQ What level of accuracy can be expected from this vice? The VMP-7L achieves an accuracy of 0.01 mm, providing the repeatability needed for tight-tolerance machining tasks. Is the vice suitable for milling centre applications? Yes — the modular machine vice from Vertex is designed for milling centres and comparable machining environments where secure clamping and repeatability are required. How heavy is the unit and why does that matter? The vice weighs 42.4 kg, a mass that helps damp vibrations and contributes to improved surface finish and tool life during machining. Can the clamping arrangement be changed for different workpieces? The modular design permits flexible set-ups and quicker reconfiguration, reducing set-up times for varied component geometries. What are the external dimensions for planning fixture space? The overall dimensions are 175x240x118 mm, which supports straightforward integration into many machine tables and fixture layouts. Manufacturer: Vertex Machinery Works Co., Ltd.; No. 296, Sec. 1, Feng Shih Road, Fengyuan District, Taichung City 420, Taiwan
176mm Live Centre Rotating For High Speeds, Accuracy 0.005 - Vertex
Take advantage of precise runout control and high‑speed capability to improve surface finish and reduce rework. Benefit from the combination of recognised Vertex manufacturing and Metav Werkzeuge’s reliable supply – order directly via Metav Werkzeuge or consult the Metav team for technical guidance. Vertex live centre MT3A – high‑speed rotating centre with 0.005 mm runout The Vertex live centre MT3A is a lathe accessory designed to support rotating workpieces at elevated spindle speeds, offering precise support for turning operations and reduced vibration in demanding production environments. High-speed rotation up to 4,000 r.p.m Precision runout 0.005 mm Morse taper MT3A interface Length 176 mm, weight 1.3 kg Consistent precision for improved component quality The primary advantage of this live centre is its focus on precision: with a measured runout 0.005 mm, the centre minimises radial error at the tailstock end, which directly improves concentricity and surface finish during turning. Reduced runout means less corrective machining and fewer rejected parts, supporting predictable cycle times. The specification for accuracy is particularly relevant in serial production and jobbing shops where repeatability influences downstream processes; the compact, engineered bearing assembly within the centre ensures this level of performance without complex setup procedures. Built for high‑speed turning and smoother machining Designed as a high‑speed rotating centre, the unit sustains operation up to 4,000 r.p.m., allowing higher cutting speeds and optimised material removal rates on modern lathes. The Morse taper MT3A interface provides straightforward mounting and secure seating in the tailstock, while the live rotation reduces tool chatter and promotes low vibration conditions. For materials and cycle types that benefit from increased spindle speed, the rotating support provided by the centre helps maintain dimensional stability and extends tool life through steadier cutting conditions. Compatibility, handling and workshop integration The compact form‑factor (length 176 mm; weight 1.3 kg) and standard taper make the centre easy to integrate into existing setups without additional adapters. As a robust lathe accessory, it is suitable for everyday workshop use and for operators who require reliable workpiece support during prolonged runs. For less experienced staff, the concept of a live centre is simple: the rotating tip follows the workpiece rotation, eliminating the sliding friction seen with fixed centres and thereby reducing heat and wear at the contact point. This tangible operational benefit improves both efficiency and safety at the machine. For reliable high‑speed support and workshop compatibility, choose the Vertex live centre MT3A and contact Metav Werkzeuge for ordering or tailored technical advice: Metav Werkzeuge, Parkring 45, 46446 Emmerich; info@metav-werkzeuge.com | +49 2822 7131930 Technical data Article number: VLC-MT3A GTIN: 4061905083594 Type: MT3A Designation: Live centre Brand: Vertex Facts Length: 176 mm Weight: 1.3 kg Accuracy (runout): 0.005 mm Max speed: 4,000 r.p.m Angle: 60° Special features Live rotating centre for high speeds Morse taper MT3A Suitable for lathe turning applications FAQ What maximum spindle speed is supported by this live centre? The live centre supports operation up to 4,000 r.p.m., allowing higher cutting speeds for compatible turning operations. How does a 0.005 mm runout affect machining results? A runout of 0.005 mm reduces radial error and vibration, improving surface finish and dimensional accuracy compared with centres that have higher runout. Is the MT3A taper compatible with standard tailstocks? Yes, the Morse taper MT3A is a common interface and fits tailstocks or adaptors designed for an MT3 taper. Can the centre be used for long production runs? The Vertex live centre is designed for routine workshop use and sustained operation, offering robust support for serial turning tasks. What advantages does a rotating centre offer over a fixed centre? A rotating (live) centre reduces sliding friction and heat at the contact point, lowering wear and promoting steadier cutting conditions. Manufacturer: Vertex Machinery Works Co., Ltd.; No. 296, Sec. 1, Feng Shih Road, Fengyuan District, Taichung City 420, Taiwan
179mm Horizontal Clamp Solid Holding Arm, 90° Angle, 5,000 N Clamping Force - Kukamet
Combine the heavy-duty 179 mm arm with a galvanised finish to achieve dependable, repeatable clamping; the high holding force and clear mounting design support uninterrupted production. Order the Kukamet 111 horizontal clamp directly via Metav Werkzeuge or ask our consultants if needed. Kukamet 111 Horizontal toggle clamp — 179 mm arm, galvanised finish A Kukamet 111 horizontal toggle clamp designed for secure horizontal fixturing in jigs and production benches. Heavy-duty 179 mm arm Galvanised corrosion resistance Holding force up to 5,000 N Horizontal base mounting Reliable clamping for repeatable assembly processes This toggle clamp is engineered for consistent clamping performance; the lever mechanism converts operator input into a secure hold, delivering a holding force that reaches 5,000 N. Such reliable force transmission reduces variation in assembly and machining setups, which enhances throughput and minimises rework. The robust action is suitable where quick manual operation and repeatability matter most, offering a measurable productivity gain over looser fixture solutions. Durable construction that cuts maintenance intervals Manufactured with a galvanised finish, the clamp resists corrosion in workshop environments and retains functionality where humidity or light contamination occurs. The heavy-duty arm design and a solid build contribute to longer service life and predictable wear characteristics. As a result, maintenance cycles are extended and downtime is reduced, supporting sustained production schedules in small workshops and light industrial settings. Straightforward installation for fast machine integration The clamp is fitted with a horizontal base that simplifies mounting to jigs, plates and fixture rails; the compact 179 mm arm delivers a clear lever reach that integrates into constrained spaces. The distinction between max clamping force (4,500 N) and static holding capacity is intentional: one value describes the compressive pressure during engagement, the other the continued retention under load. This separation helps engineers choose the correct clamp for specific fixture demands and prevents overspecification. Practical fit for trade workshops and production cells Designed as a standard component for manual fixturing, the clamp suits fabrication shops, assembly benches and testing jigs where reliable, repeatable fixing is required. The compact footprint and familiar toggle action make it easy for technicians to adopt, while the galvanised surface and solid construction support long-term asset value. Combined with Metav’s supply and quality screening, the solution is aimed at teams seeking affordable precision without compromise. Contact Metav Werkzeuge today to specify the Kukamet 111 for fixture applications or for tailored technical advice — email info@metav-werkzeuge.com or call +49 2822 7131930 Technical data SKU: 111-5-D-C2 GTIN: 8680731500325 ETIM: EC011973 ECLASS: 21041719 Manufacturer: Kukamet Performance data Arm length: 179 mm Angle: 90° Weight: 1.48 kg Max clamping force: 4,500 N Max holding force: 5,000 N Materials & special features Galvanised finish Horizontal base mounting Massive holding arm Toggle clamp (lever clamp) design FAQ What maximum holding force does the clamp provide? The Kukamet 111 horizontal toggle clamp offers a maximum holding force of 5,000 N, specified for static retention under load. What is the effective clamping pressure during engagement? The clamp reaches a maximum clamping (compressive) force of 4,500 N when the lever is fully engaged. How is the clamp mounted? The unit is supplied for horizontal base mounting and is suited to jig plates and fixture rails that accommodate a horizontal foot. What material and surface protection does the clamp have? The clamp is finished in galvanised steel, providing improved corrosion resistance for typical workshop conditions. Is the arm length suitable for compact fixtures? With a 179 mm arm, the clamp offers a compact lever reach that is compatible with constrained fixture designs while maintaining effective clamping action. Manufacturer: Kukamet Fevzi Çakmak Mah.10644 Sk. No:61-63 42050 Karatay / KONYA TÜRKİYE / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com
179mm Precision Steel Clamping Jaw 12/14/16/18 Nut Slots, H Max 99 - AMF
Benefit from the robust steel construction and multi-size compatibility (12/14/16/18 mm) for repeatable, secure clamping; order the AMF No. 6497 via Metav Werkzeuge or consult our specialists for application advice. Stable clamping jaw No. 6497 — Steel clamping jaw with multi-size compatibility The Stable clamping jaw No. 6497 is a steel clamping insert designed for precision workholding in workshop and production environments, compatible with common insert sizes and engineered for repeatable fixture setups. Durable steel construction Compatible with 12/14/16/18 mm inserts Total length 179 mm for secure grip h1 38 mm, H max 99 mm specification Precise, repeatable clamping for production workflows Engineered to support accurate and consistent part holding, this steel clamping jaw delivers measurable improvements in setup repeatability. With a total length of 179 mm and clear dimensional limits such as h1: 38 mm and H max.: 99 mm, the component reduces variability in clamping height and contact area. The multiple insert compatibility (12/14/16/18 mm) allows a single jaw to be adapted across a range of workpieces and fixtures, shortening changeover time and simplifying inventory. This focus on dimensional clarity and precision supports tighter process control and fewer rejects in batch production. Robust design that lowers maintenance and downtime Made from durable steel and produced to industrial standards, the jaw is built to withstand frequent use in demanding environments. The solid construction improves wear resistance and maintains gripping contours over longer service intervals, contributing to higher machine availability. By choosing a component with defined maximum dimensions (H max.: 99 mm) and a standardised engagement height (h1: 38 mm), teams can forecast service windows and stocking needs more accurately, improving overall equipment efficiency and reducing unexpected stoppages. Easy integration into existing clamping systems and workshops Compatibility with standard insert sizes makes this clamping jaw straightforward to integrate into established clamping plates and vises, avoiding bespoke modifications. The clear dimensional data and standardised sizes facilitate procurement and spare-part planning: one part covers multiple use cases. Combined with the brand reliability associated with AMF, this solution supports streamlined logistics and a consistent quality baseline across job orders. For operations seeking a pragmatic balance between adaptability and structural integrity, the component is a practical choice. For secure, precision clamping from AMF, contact Metav Werkzeuge in Emmerich for tailored procurement and technical guidance at info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: 4000833184NW Type: Nr. 6497 Description: Stable steel clamping jaw No. 6497, 12/14/16/18 mm, AMF Product type: Steel clamping jaw Manufacturer: AMF Packaging unit: 1 Facts Total length: 179 mm Width: 19 mm Insert compatibility: 12 mm / 14 mm / 16 mm / 18 mm h1: 38 mm H max.: 99 mm Special features Material: steel Addition: Nut: /14/16/18 Designed for repeatable clamping and secure grip Suitable for standard clamping systems and fixtures FAQ What materials is the clamping jaw suitable for? The AMF Stable clamping jaw No. 6497 is a steel clamping jaw intended for holding a wide range of workpiece materials when used with appropriate inserts; material-specific suitability depends on the chosen insert and clamping setup. Which insert sizes fit this jaw? This jaw accepts 12/14/16/18 mm inserts, as specified for the No. 6497, enabling flexible use across multiple part geometries. What are the key dimensions to consider when fitting the jaw? Key dimensions: total length 179 mm, width 19 mm, engagement height h1: 38 mm and maximum height H max.: 99 mm; these determine compatibility with plates and vises. Is this item available as a single unit and what is the SKU? Yes, the product is supplied per packaging unit 1. SKU / Article number: 4000833184NW. How does this jaw improve workshop efficiency? By combining standardised insert compatibility with robust steel construction and defined clamping dimensions, the jaw reduces changeover time and improves setup repeatability, supporting smoother production runs. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
17mm 5C Collet High-Precision 0.02mm Runout, 87mm Length - Vertex
The combination of 0.02 mm concentricity and standard 5C compatibility delivers repeatable, high-quality clamping for precision turning and milling. The compact 87 mm length and light 0.21 kg mass simplify handling and reduce spindle load. Order the collet directly via Metav Werkzeuge or ask our consultants if clarification is required. 5C-17 collet — 17 mm, 0.02 mm accuracy, Vertex The 5C-17 collet is a 5C clamping sleeve designed to secure cylindrical workpieces in lathes and fixtures where high concentricity and repeatability are required 5C system for standard collet chucks 17 mm clamping diameter 0.02 mm concentricity accuracy Compact 87 mm body length Increased accuracy for consistent machining results High precision clamping reduces scrap and improves part uniformity. With a stated 0.02 mm concentricity figure, the sleeve supports repeatable positioning that benefits both one-off and batch production. The measurable tolerance gives a clear technical basis for process planning and enables reliable specification of downstream operations. This level of control is particularly valuable where tight tolerances and surface finish matters are decisive for final assembly. Seamless integration with existing 5C tooling Compatibility with the 5C system simplifies tooling logistics and shortens setup times. The collet’s 17 mm clamping diameter and standard interface allow direct use in common collet chucks and fixtures without additional adaptors. The compact 87 mm body length helps maintain machine balance and provides straightforward access for tool changes, while the modest 0.21 kg weight contributes to reduced spindle inertia and easier handling during set-up. Practical benefits that reduce operational risk A reliable clamping sleeve like this one supports process stability and lowers the likelihood of rework. The robust design intent and verified concentricity contribute to predictable tool life and steady cycle times. For workshops seeking measurable improvements in throughput, the combination of standard form factor and documented performance helps to integrate the component into quality control routines and production documentation with minimal overhead. Contact Metav Werkzeuge for tailored advice on Vertex 5C collets and secure a dependable clamping solution supplied from our Emmerich warehouse Technical data Article number: 5C-17 GTIN: 4061905088575 Manufacturer: Vertex Core measurements Clamping diameter: 17 mm Length: 87 mm Weight: 0.21 kg Concentricity / accuracy: 0.02 mm eClass: 21041712 Special features 5C system compatibility Standard collet chuck interface SKU: 5C-17 FAQ What clamping diameter does the collet provide? The collet offers a 17 mm clamping diameter as stated for the Vertex 5C-17 collet. Is the sleeve compatible with standard 5C collet chucks? Yes. The design conforms to the 5C system and fits standard 5C collet chucks. What concentricity or accuracy can be expected? The stated concentricity accuracy is 0.02 mm for the Vertex 5C-17 collet. How long and heavy is the clamping sleeve? Length is 87 mm and weight is 0.21 kg for the 5C-17 collet. Is the collet suitable for serial production where repeatability matters? Yes; the documented accuracy and standard interface make the collet suitable for production environments requiring repeatable clamping. Manufacturer: Vertex Machinery Works Co., Ltd.; No. 296, Sec. 1, Feng Shih Road, Fengyuan District, Taichung City 420, Taiwan
Secure components with reliable workpiece clamps
Workpiece clamps, also known as workholding clamps or workholding devices, form the essential mechanical interface between machine and part in industrial fabrication. They keep components absolutely play-free, positionally accurate and vibration-resistant during milling, turning, drilling or grinding.
How workpiece clamps ensure process stability
A correctly specified clamping concept transfers the high cutting and feed forces of modern CNC machines into the machine table or spindle without deforming the part. The right combination of mechanical, hydraulic, pneumatic or magnetic solutions enables fast, repeatable setups and supports automated part change where required. Typical applications range from single-part turning to high-volume series milling and complex five-axis machining.
Concrete production benefits at a glance
- repeatable positioning: reduces scrap and rework
- high clamping forces: withstands aggressive cutting without part movement
- reduced set-up time: modular systems and quick-change features speed throughput
- improved surface finish: vibration damping for finer results and tighter tolerances
- flexible compatibility: vices, chucks, clamping plates and zero-point systems for diverse geometries
Why Metav's range is the practical choice
Metav combines decades of specialist know-how with a broad, handpicked range that democratises precision for workshops and industry alike. Based in Emmerich, Metav acts as a quality filter for the European market and supplies more than 250,000 products from precision metrology to complete workshop equipment. With the trust of over 48,000 customers, Metav offers a single-source approach that reduces supplier complexity and secures dependable delivery to your workbench.
Technical data
- function: mechanical interface between machine and workpiece
- primary requirements: absolute positional accuracy; vibration reduction; high clamping forces
- technologies: mechanical, hydraulic, pneumatic, magnetic
- typical components: machine vices; chucks; clamping plates; zero-point systems; pratzen; clamping jaws
- application areas: milling; turning; drilling; grinding; automated part change systems
- production benefits: reduced set-up time; enhanced process security; optimised series and single-part production
The practical summary
Workpiece clamps bring the stability and repeatability required to meet tight tolerances and excellent surface quality, making them indispensable across machining operations. Choosing the right workholding clamps and modular workholding devices is a decisive step towards higher productivity and consistent part quality.
FAQ
What types of workpiece clamps are suitable for automated machining?
Workholding clamps with quick-change modules, hydraulic actuation or magnetic systems are commonly used for automated machining. These workholding devices enable fast, repeatable part changes and integrate with zero-point systems.
How do workpiece clamps affect surface finish and tolerances?
A stable clamping concept minimises vibration and part movement; this improves surface finish and supports achieving narrow tolerances when using high-precision workpiece clamps or workholding devices.
Can the same workpiece clamps handle different part geometries?
Modular workholding clamps and adaptable clamping jaws allow flexible fixturing for varied geometries; combining vices, clamping plates and pratzen increases versatility on the shopfloor.
Fragen zu diesen Produkten??
Mit mehr als 30 Jahren Erfahrung beraten wir Sie gerne persönlich.
Tel.: +49 2822 7131930
Mail: info@metav-werkzeuge.com