25mm Thickness Gauge Digital For Soft Materials With Ø5mm Anvils, 0.0001mm Resolution, ISO 4584‑R - Microtech Metrology
€1,590.00
Product information "25mm Thickness Gauge Digital For Soft Materials With Ø5mm Anvils, 0.0001mm Resolution, ISO 4584‑R - Microtech Metrology"
A compact digital thickness gauge that combines high resolution and a low, controlled contact force to deliver reliable measurements of delicate materials; the 0–25 mm range and ISO 4584‑R conformity make it suitable for routine quality control. Order this instrument directly via Metav Werkzeuge or contact our consultants for application advice.
Digital Thickness Gauge by Microtech Metrology — 0–25 mm, resolution to 0.001 mm
The Thickness Gauge is a digital measuring instrument for accurate thickness checks on soft materials such as plastics, films and sheets.
- Digital readout with 0.001 mm resolution
- Measuring range 0–25 mm
- Low contact force 0.5 N ±0.025 N
- ISO 4584‑R compliant measuring routine
Precision adapted to soft materials
The device offers a digital readout with a finest resolution down to 0.001 mm, combined with a display reading step of 0.0001 mm. This balance of coarse range and fine resolution enables consistent detection of subtle thickness differences across the full 0–25 mm span. Conformity with ISO 4584‑R underlines suitability for standardised thickness measurement procedures and supports repeatable production checks.
Gentle contact for delicate surfaces
A controlled contact mechanism applies measuring force 0.5 N ±0.025 N to the test specimen while the measuring faces are small and focused (Ø5 mm), which reduces local deformation and prevents compression of flexible materials. That combination is particularly important when inspecting films, thin plastics and paper where a heavier probe would distort results. The instrument therefore preserves sample integrity while delivering reproducible readings.
Built for workshop and inspection routines
The instrument bridges shop‑floor durability and inspection‑level clarity: a straightforward digital interface speeds up routine thickness checks, while an accuracy specification ranging from 0.001–0.15 mm reflects performance across different setups and sample conditions. The design supports rapid throughput in production and provides the traceable data consistency required for incoming goods inspection or process control.
Practical use and application scope
Intended for use with plastics, films and sheets, the gauge suits laboratory benches and production lines where frequent, non‑destructive thickness verification is needed. Its compact footprint and digital display make it easy to read and document measurements, while the modest contact force minimises handling artefacts. The instrument is an effective tool for quality assurance of soft, compliant materials.
Contact Metav Werkzeuge for application guidance or to request this Microtech Metrology digital thickness gauge for your production process
Technical Data
- Article number: 137331270
- GTIN: 4061905451737
- Manufacturer: Microtech Metrology
Facts
- Measuring range: 0–25 mm
- Display reading step: 0.0001 mm
- Accuracy / resolution range: 0.001–0.15 mm
- Measuring force: 0.5 N ±0.025 N
- Measuring faces diameter: Ø5 mm
Special features
- Digital instrument (digital: true)
- Norm conformity: ISO 4584‑R
- Suitable for plastics, films and sheets
- No timer function indicated (Ohne Timer)
FAQ
How accurate is the measurement with this thickness gauge?
The Microtech Metrology digital thickness gauge provides a resolution down to 0.001 mm and an accuracy span of 0.001–0.15 mm depending on measuring conditions; the display step is 0.0001 mm for clear readout.
Can the instrument be used on very thin film and paper?
Yes, the gauge is designed for soft, compliant materials such as films and thin plastics; the low contact force of 0.5 N ±0.025 N and Ø5 mm measuring faces reduce deformation during measurement.
What measuring range does the device cover?
The instrument covers a measuring range of 0–25 mm, making it suitable for a wide variety of thickness checks within that span.
Is the instrument suitable for routine quality control in production?
Yes, conformity to ISO 4584‑R and the combination of robust digital readout and repeatable contact force make it appropriate for production line and laboratory routines.
Manufacturer / Responsible: Microtech, Nizhneyurkovska str., 45a, 04080 Kyiv, Ukraine; tool@microtech.tools
Datenübertragung Sets
The provided product data contains contradictory specifications that prevent creation of a reliable product description. The item is described alternately as a mobile, IP67-rated button and as a desktop two‑button panel with an IP40 protection rating; these descriptions are mutually exclusive. Because of this inconsistency it is not possible to produce a compliant, accurate product text, as core functional and environmental details remain unclear. Please clarify which variant is intended (mobile or desktop), and confirm the correct ingress protection rating, battery specification, and principal connectivity features. Additionally, verify the device dimensions, weight and whether data output or synchronisation to the MICROTECH MDS app and instrument memory are required as primary functions. Once these key specifications are resolved and supplied consistently, a full British‑English product description meeting all structural and editorial requirements can be generated promptly.
Take advantage of a ready-to-run data-collection solution that combines reliable Windows software with a compact hardware interface and seamless instrument synchronisation; the set supports zero setting and autoconnection for efficient workshop workflows. Order the accessory set directly via Metav Werkzeuge or contact our consultants for tailored integration advice. MDS Standard accessory set — Windows data-collection kit for Microtech metrology The MDS Standard accessory set is a compact data-collection kit designed to integrate Microtech metrology instruments into Windows-based measurement routines across workshop and quality-control environments. Ready-to-run MDS data collection set Includes Windows MDS 5.5 application Single USB dongle for secure connection Connects up to three Microtech instruments Faster, more reliable measurement logging for everyday workshop use The accessory set brings a ready-to-run approach to data capture: the included MDS 5.5 application for Windows and the USB interface reduce setup time and lower the administrative burden of manual entry. Autoconnection and synchronisation of data reading reduce transcription errors and improve traceability for production and inspection tasks. For routine quality-control cycles, this means fewer interruptions and a more consistent data stream from handheld and bench metrology devices. Stable connectivity and simple expansion for mixed workloads Equipped with a single USB dongle and designed for multiple connection modes, the kit allows the simultaneous integration of up to three instruments, supporting parallel measurement of components or multiple operators at workstations. The autoconnection feature ensures instruments are recognised automatically after sleep or reconnection, while the optional footswitch and DataMet buttons enable hands-free data capture and straightforward zero setting, which speeds up repetitive measurement sequences and reduces operator fatigue. Clear, verifiable data flow that simplifies reporting and traceability The system focuses on delivering a clean data path from instrument to PC: readings are synchronised and recorded directly via the Windows app, enabling immediate export or incorporation into existing inspection workflows. For workshops aiming to tighten process control, this accessory kit supports consistent data logging without complex network configuration. The compact kit is especially useful where fast deployment and minimal training time are priorities, as installation and initial pairing are engineered for immediate operation. Contact Metav Werkzeuge for assistance with system selection and integration of the MDS Standard accessory set — Metav Werkzeuge provides fast delivery from Emmerich and expert advice via info@metav-werkzeuge.com or +49 2822 7131930 Technical Data Article number: 299110504 GTIN: 4061905452109 Manufacturer: Microtech Metrology Label: Standard MDS data set for Windows Core data Software: MDS 5.5 (Windows) USB dongle: 1 Maximum connections: 3 Special features Ready data collecting solution from box Data reading synchronisation and connection modes Autoconnection for Microtech instruments Zero setting via software and optional footswitch Optional DataMet buttons and footswitch for hands-free capture FAQ What instruments can be connected with the accessory set? The accessory set supports connection of Microtech metrology instruments and can handle up to three devices simultaneously via the included USB dongle. Is special software required to record measurements? Yes, the set includes the MDS 5.5 application for Windows, which handles data capture, synchronisation and export. Can measurements be taken hands-free? Yes, the kit is compatible with optional DataMet buttons and a footswitch for hands-free data capture and for performing zero setting. How does autoconnection improve daily operation? Autoconnection lets instruments reconnect automatically after disconnection or sleep, ensuring continuous data logging and reducing setup interruptions during production runs. Manufacturer / Responsible: Microtech, Nizhneyurkovska str., 45a, 04080 Kyiv, Ukraine, tool@microtech.tools
Benefit from robust IP67 protection combined with simple two‑button operation and a built‑in 500 mAh Li‑Pol battery for reliable zero‑setting and direct data saving. Order the DataMet Mobile Button IP67 directly via Metav Werkzeuge or consult our specialists for tailored configurations. DATA BUTTONS DataMet IP67 — wireless two‑button control unit with IP67 protection DATA BUTTONS DataMet IP67 is a compact wireless control unit for quick zero setting and automatic data transfer with Microtech instruments and the MDS Windows application. *IP67 waterproof protection for harsh environments *Two-button operation for zeroing and data save *Rechargeable 500 mAh Li-Pol battery built in *Saves and synchronises with MDS app for Windows Streamline measurement workflows with direct wireless control The compact controller enables immediate zero setting and data saving without returning to the instrument, reducing handling time and process interruptions. As a multifunctional interface for Microtech instruments and the MDS app (Windows), the unit supports both local memory storage and app synchronisation, allowing traceable measurement records and efficient batch captures. This reduces manual transfer errors and shortens inspection cycles, improving throughput in production and quality control. Durable, portable design for on‑site and bench use Built to IP67 standards, the device resists dust and temporary immersion, making it suitable for demanding shop‑floor environments. The rechargeable Li‑Pol 500 mAh battery provides dependable operation and is integrated to avoid the need for disposable cells. With dimensions of 75 x 50 x 30 mm, a weight of 0.15 kg and a 10 mm button diameter, the controller is ergonomically easy to handle whether used as a mobile stick or a desktop panel. Visual feedback is provided via an LED status indication, ensuring clear operation confirmation in noisy or busy settings. Flexible integration and custom configuration options Connection is implemented for seamless pairing with Microtech measurement instruments and synchronisation to the MDS app for Windows, enabling data to be written either to the instrument memory or directly to the application. Two physical buttons cover the primary functions—zero and save—while additional custom functions can be specified on request for specialised workflows. Available as a mobile two‑button stick or a desktop two‑button panel, the unit adapts to both handheld inspection and fixed workstation setups, simplifying retrofit projects and mixed‑device fleets. Contact Metav Werkzeuge for expert advice on integrating the Microtech Metrology DataMet IP67 into existing measurement workflows and to request a tailored configuration from our Emmerich warehouse Technical data Article number: 299900012 Label: DATA BUTTONS DataMet IP67 Manufacturer: Microtech Metrology Facts Buttons: 2 Battery: 500 mAh Li‑Pol Button diameter: 10 mm Dimensions: 75 x 50 x 30 mm Weight: 0.15 kg Protection class: IP67 Special features Wireless connection to Microtech instruments Synchronises with MICROTECH MDS app for Windows Saves data to instrument memory or MDS app LED status indication Available as mobile stick or desktop panel Custom functions available on request Built‑in rechargeable battery FAQ How does the controller connect to measurement instruments? The DataMet Mobile Button IP67 connects wirelessly to Microtech Metrology instruments and synchronises readings with the MICROTECH MDS app for Windows, allowing both local memory storage and app‑based saving. Can the device be used in wet or dusty production areas? Yes. The DataMet Mobile Button IP67 is IP67 rated, making the unit dust‑tight and protected against temporary immersion, suitable for challenging shop‑floor environments. What battery life and maintenance are expected? The unit employs a built‑in 500 mAh Li‑Pol battery; typical uptime depends on usage patterns, but rechargeable design eliminates disposable cell changes and simplifies upkeep for the DataMet Mobile Button IP67. Are custom functions or different housings available? Custom functions can be requested for specialised workflows; the controller is available as a mobile two‑button stick or as a desktop two‑button panel to suit specific application needs for the DataMet Mobile Button IP67. Is visual feedback provided for successful operations? Yes. The device includes an LED status indication that shows connection and save status, ensuring clear confirmation of zeroing and data storage actions for the DataMet Mobile Button IP67. Manufacturer / Responsible: Microtech, Nizhneyurkovska str., 45a, 04080 Kyiv, Ukraine; tool@microtech.tools
Take advantage of a ready-to-use data-collection solution that combines MDS 5.5 PRO Windows software, autoconnection and data synchronisation with tangible hardware: two USB dongles and two 1 m cables enable simultaneous linking of multiple instruments. Order the accessory kit directly via Metav Werkzeuge or consult our specialists for integration advice. Accessory kit — MDS Connection Set by Microtech Metrology (ready-to-use data-collection solution, Windows) Accessory kit provides an immediate, workshop-ready interface for collecting measurement data from Microtech instruments and performing zero setting via the bundled software Ready-to-use data-collection kit Includes MDS 5.5 PRO software licence Two USB dongles and two 1 m cables Supports up to 10 simultaneous connections Faster, error-resistant data capture from the first connection The MDS 5.5 PRO software bundled with this accessory kit turns standard measurement routines into a streamlined data flow. With autoconnection and data synchronisation, instrument readings are transferred with minimal manual intervention, reducing transcription errors and saving time in quality-control cycles. As a ready-to-use collection solution, the set supports direct zero setting on compatible devices and accelerates the handover of digital records into inspection protocols, making traceable measurement workflows feasible without complex custom integration. Flexible hardware that scales with workshop needs Hardware in the connection set is configured to suit multi-instrument setups: two USB dongles, two 1 m cables and optional DataMet Buttons or a footswitch enable local control and convenient data capture. The kit supports up to 10 connections, allowing several gauges or probes to be connected concurrently for batch inspections or station-based monitoring. This arrangement reduces cable clutter and simplifies station layout while enabling concurrent data capture from multiple sources, which increases throughput in repetitive measurement tasks. Simple integration and predictable operation for production use Designed for seamless integration with Microtech instruments, the connection set provides a consistent interface for data collection and storage. The package is supplied as a complete set and is particularly useful where standardised data logging and repeatable zeroing are required. Built for workshop resilience, the combination of compact dongles and short, robust cables offers dependable day-to-day operation and straightforward replacement of individual components when needed. The clear separation of software and hardware functions makes updates and maintenance predictable and cost-effective. For tailored supply and expert guidance on integrating the Microtech connection set into existing measurement workflows, contact Metav Werkzeuge for a pragmatic consultation and rapid delivery from Emmerich—call +49 2822 7131930 or email info@metav-werkzeuge.com Technical data Article number: 299110810 GTIN: 4061905452673 Manufacturer: Microtech Metrology Max connections: 10 USB dongles (PRO): 2 Cables (1 m): 2 Kit pieces per set: 5 MDS 5.5 PRO app for Windows Ready data-collection solution from box Autoconnection and data synchronisation Optional DataMet Buttons and footswitch FAQ What is included in the accessory kit? The accessory kit contains the MDS connection hardware and software components: two USB dongles, two 1 m cables, the MDS 5.5 PRO application for Windows and the set contents as listed under article number 299110810. Can the connection set work with multiple Microtech instruments at once? Yes, the MDS Connection Set is engineered to support up to 10 simultaneous connections with Microtech instruments, enabling concurrent data capture across several devices. Is the supplied software compatible with standard Windows systems? The MDS 5.5 PRO app bundled with the connection set is designed for Windows platforms and facilitates data synchronisation and zero setting for Microtech Metrology devices. Are optional control devices included or sold separately? Optional items such as DataMet Buttons and a footswitch are referenced as available accessories; the core set lists them as optional for localised data collection control. How does the kit improve measurement workflows? By combining autoconnection, immediate zero setting and centralised data synchronisation, the connection set reduces manual steps and transcription errors, streamlining measurement logging in routine quality checks. Manufacturer / Responsible: Microtech, Nizhneyurkovska str., 45a, 04080 Kyiv, Ukraine, tool@microtech.tools
Take advantage of the combination of autoconnection, data synchronisation and a complete Windows application for faster quality checks and fewer transcription errors; order the OPTIMA MDS data set directly via Metav Werkzeuge or ask our consultants if needed. OPTIMA MDS data set — Data-collection kit with MDS 5.5 and autoconnection The OPTIMA MDS data set is a ready-to-use data-collection solution for Microtech measurement instruments, designed for shop-floor and lab environments to automate readings, perform zero-setting and synchronise measurement data under Windows. Ready data-collecting solution from box Autoconnection and data synchronisation Includes MDS 5.5 Windows app and USB dongles Reliable data capture for inspection workflows The kit brings a pragmatic route to digital measurement capture by combining the MDS 5.5 Windows application with immediate hardware for connection. Built-in autoconnection and continuous data synchronisation reduce manual entry and cut reporting time, while support for max connections 6 enables concurrent monitoring of several instruments. Two USB dongles and two 1 m cables are included to start data acquisition straight away, which accelerates batch inspections and makes logging reproducible. The technical approach removes routine friction from quality-control loops and clarifies traceability for production records. Hands-free and flexible collection to suit production Workflows that demand fast, repeatable capture benefit from the available hands-free options: optional DataMet Buttons and a footswitch allow tactile data collection and instant zero setting, keeping operator interaction steady and consistent. Zero-setting at the instrument removes offset errors before measurement sequences, which is particularly useful when switching fixtures or aligning gauges. The set's connection modes and synchronised reading strategy permit consistent sampling across varying measurement tasks, improving throughput in both repetitive production and small-batch inspection. Quick installation and Windows integration for fast ROI Installation focuses on rapid deployment: the solution is ready-to-use with the included software and hardware, minimising setup time on Windows workstations. The MDS 5.5 standard app handles data recording and export, while the included cables and dongles avoid extra procurement steps. This plug-and-play characteristic shortens the path to measurable benefits, such as fewer non-conformances and faster data reporting cycles. Compatibility with Microtech instruments ensures that measurement signals are interpreted correctly and handed off in a consistent format for downstream analysis. Scalable, shop-floor friendly solution for consistent measurements The configuration supports small multi-instrument setups and can be extended within its six-connection limit to cover typical bench-level requirements. Synchronised readings and automated connection handling reduce operator variability and enhance overall measurement reliability, making the system suitable for both workshop quality checks and laboratory documentation. Optional accessories allow adaptation to specific processes without altering the core collection workflow, preserving data integrity while supporting productivity improvements. Choose Microtech-grade data capture with the OPTIMA MDS data set and contact Metav Werkzeuge in Emmerich for tailored advice and secure supply: info@metav-werkzeuge.com or call +49 2822 7131930 Technical Data Article number: 299110506 Label: OPTIMA MDS data set Manufacturer: Microtech Metrology Application: MDS 5.5 STANDARD app for Windows Facts SKU / UID: 299110506 Max connections: 6 USB dongles: 2 Cables: 1 m (2 pieces) Special features Ready data-collecting solution from box Autoconnection and data reading synchronising Connection modes for flexible setups Optional DataMet Buttons and footswitch for collection and zero setting Collects data from Microtech instruments and supports zero setting FAQ What does the kit include? The OPTIMA MDS data set includes the MDS 5.5 STANDARD application for Windows, two USB dongles and two 1 m cables; optional DataMet Buttons and a footswitch are available for hands-free collection. How many instruments can be connected at once? The system supports a maximum of 6 simultaneous connections, allowing several Microtech instruments to be monitored and logged in parallel. Is zero setting supported during collection? Yes, zero setting is supported; the OPTIMA MDS data set provides zero-setting functionality and optional footswitch or button control for repeatable baseline procedures. Which operating system is required? The MDS 5.5 STANDARD application operates on Windows, as supplied with the data-collection kit for straightforward integration into typical inspection stations. Are hands-free controls included as standard? Hands-free controls such as the footswitch and DataMet Buttons are listed as optional accessories; the standard delivery contains the software, two USB dongles and two 1 m cables. Manufacturer / Responsible: Microtech, Nizhneyurkovska str., 45a, 04080 Kyiv, Ukraine; tool@microtech.tools
Reliable, ready-to-run data collection is achieved by combining autoconnection, the MDS 5.5 PRO Windows app and the IP67 DataMET interface, enabling synchronised readings and rapid zero setting for reduced downtime. Order the accessory set directly via Metav Werkzeuge or ask our consultants if needed. Microtech Metrology MDS PRO Connection Accessory Set — ready-to-use data collection, up to 18 connections The Microtech Metrology MDS PRO Connection Accessory Set is a compact, preconfigured kit for integrating Microtech measuring instruments into a Windows-based data workflow, designed for production environments and quality labs. Ready-to-run data collection kit Up to 18 simultaneous connections Includes MDS 5.5 PRO Windows app IP67 DataMET 2-button interface included Faster, centralised measurement logging for production control The kit delivers centralised data capture by pairing the MDS 5.5 PRO software with hardware that automates device links and reading transfer. Autoconnection and synchronising functions remove manual entry steps, cutting transcription errors and saving hands-on time during inspection cycles. With support for multiple dongles and interfaces, the system scales to mid-size benches and assembly lines while maintaining consistent data flow and auditability for quality processes. Durable interface and practical peripherals for shop-floor use Hardware in the set is selected for reliability: DataMET IP67 ensures the primary interface tolerates humid or oily environments, while the supplied USB dongles and 1 m cables provide straightforward, tool-free connections. Optional footswitch and extra DataMET buttons allow ergonomic data capture that reduces operator movement and cycle time. These physical features minimise interruptions and contribute directly to repeatable acquisition under typical workshop conditions. Ready-to-deploy workflow with traceable zeroing and broad compatibility Out of the box readiness and integrated zero setting mean the system is live quickly, simplifying commissioning. The combination of automatic zeroing and synchronised readings supports traceability, simplifying downstream reporting and reducing inspection variance. Designed to work with Microtech instruments, the set supports simultaneous links (up to 18 connections) so small networks of measuring devices can feed a single Windows instance for consolidated reporting and control. For fast integration and reliable, shop-floor grade data capture, contact Metav Werkzeuge in Emmerich to order the Microtech accessory set or request tailored advice: info@metav-werkzeuge.com / +49 2822 7131930 Technical Data Article number: 299110840 GTIN: 4061905452680 Brand: Microtech Metrology Core technical data Max connections: 18 USB dongles: 3 Cable length: 1 m (3 cables) DataMET IP67 units: 1 Special features MDS 5.5 PRO app for Windows Autoconnection Data reading synchronising Zero setting function Optional DataMET buttons and footswitch Ready-to-use out of the box FAQ What operating system is required for the kit? The MDS PRO Connection Accessory Set uses the MDS 5.5 PRO application, which is supplied for Windows environments and configured for immediate deployment. How many instruments can be connected at once? The package supports up to 18 connections, allowing multiple Microtech instruments to stream readings into one central Windows instance. What does the kit include as standard? Contents include the MDS 5.5 PRO app (Windows), 3 USB dongles, 3 × 1 m cables, 1 × DataMET IP67 (2-button) interface, and options for additional DataMET buttons or a footswitch; SKU 299110840 identifies this set. Is the DataMET interface suitable for harsh environments? Yes, the DataMET unit is IP67-rated, providing dust-tight protection and temporary immersion resistance for robust shop-floor performance. Manufacturer / Responsible: Microtech, Nizhneyurkovska str., 45a, 04080 Kyiv, Ukraine, tool@microtech.tools
Take advantage of a ready-to-use data-collection kit that combines autoconnection, reliable zero setting and broad multi-device support to reduce cycle times and transcription errors. Order directly via Metav Werkzeuge or consult our specialists for configuration advice and integration options. PRO-DESK MDS data set — Desktop data-collection kit with MDS 5.5 PRO and multi-device support (Microtech Metrology) PRO-DESK MDS data set is a compact, ready-to-deploy solution for collecting measurement data from Microtech instruments and feeding it into Windows-based workflows, ideal for workshop benches and small lab environments. Complete MDS data-collection set Autoconnection and automatic syncing Includes DataMet button and footswitch Supports up to 40 simultaneous connections Cut paperwork and speed up measurement cycles The PRO-DESK MDS data set pairs the MDS 5.5 PRO Windows application with a hardware kit to remove repetitive manual entry. The kit's autoconnection feature automatically recognises attached Microtech instruments and assigns data channels, while the built-in zero setting streamlines reference captures. This reduces hand‑offs between measurement and data systems, shortens throughput times and improves process repeatability by ensuring that each measurement is captured electronically and consistently. Centralised capture from multiple instruments Designed for busy benches and small-scale test rigs, the set supports up to 40 connections and ships with USB dongles and short cables for rapid deployment. Centralised capture means readings from several gauges or probes are aggregated into a single dataset, enabling faster statistical checks and quicker decision-making on the shop floor. The net effect is less context switching for operators and a measurable improvement in data availability for quality control. Hands-free capture and reliable reference control The kit includes a desktop DataMet Button and allows the use of optional footswitches or additional push-buttons for hands-free data collection and to trigger zero setting without interrupting a setup. Hands-free capture reduces handling-induced variation and accelerates routine inspections. For procedures requiring tactile control, physical triggers provide immediate confirmation of a captured reading and help maintain operator ergonomics during repetitive tasks. Seamless Windows integration and safeguarded data flow The supplied MDS 5.5 PRO app runs on Windows and supports multiple connection modes and automatic data synchronisation, making transfer to inspection software or spreadsheets straightforward. Connection modes permit local buffering when networks are variable and ensure that no readings are lost during brief interruptions. Explaining the term: data synchronisation here means measured values are matched to timestamps and instrument IDs so traceability is preserved for quality documentation. A practical fit for workshop and lab workflows Beyond technical capability, the set is built for pragmatic use: quick physical installation, simple software setup and clear visual feedback during capture. The collected data is suitable for standard SPC tasks or for feeding into existing measurement systems, reducing manual transcription and potential human error. Taken together, the configuration supports faster inspection cycles and a more reliable audit trail—advantages that benefit production technicians and quality engineers alike. Talk to Metav Werkzeuge about integrating Microtech Metrology’s PRO‑DESK MDS data set into existing test benches and production lines for dependable multi‑instrument data capture and faster measurement workflows Technical data Article number: 299110860 Name: PRO-DESK MDS data set Manufacturer: Microtech Metrology Application: MDS 5.5 PRO app for Windows Facts Max connections: 40 USB dongles (PRO): 8 Cables (1 m): 8 DataMet Desktop Button: 1 Special features Autoconnection Data reading synchronisation Zero setting function Optional footswitch and additional DataMet buttons Ready data-collection solution for Microtech instruments FAQ What instruments can be connected to the PRO‑DESK MDS data set? The PRO‑DESK MDS data set collects readings from Microtech Metrology instruments and is configured for common output types supported by the MDS 5.5 PRO Windows application. How many devices can be managed simultaneously? The system supports up to 40 simultaneous connections, made possible by the included USB dongles and connection architecture. Is hands‑free capture possible with the kit? Yes. The set includes a DataMet desktop button and supports optional footswitches to enable hands‑free capture and zero setting during measurement cycles. Does the software preserve traceability for quality records? Data collected via MDS 5.5 PRO is synchronised with timestamps and instrument identifiers, ensuring traceability suitable for routine quality documentation and SPC workflows. Which operating system is required for the software? MDS 5.5 PRO runs on Windows; the PRO‑DESK MDS data set is intended for integration into Windows‑based measurement workflows. Manufacturer / Responsible: Microtech, Nizhneyurkovska str., 45a, 04080 Kyiv, Ukraine, tool@microtech.tools
Datenübertragung
Take advantage of stable wireless data transfer and simple Windows integration to eliminate manual entries and accelerate quality workflows; the choice between STANDARD (up to 3 instruments) and PRO (up to 8 instruments) allows scalable deployment. Order the interface directly via Metav Werkzeuge or consult our team for configuration advice. USB Dongle — Microtech Metrology wireless Windows interface, up to 8 instruments (PRO) The USB Dongle provides a dedicated wireless link between Microtech measuring instruments and the MDS application for Windows, enabling secure data capture across workshop benches and measurement stations. Stable wireless data transfer up to 50 metres STANDARD: connects up to 3 instruments PRO: connects up to 8 instruments Includes 1 m MDS USB extension cable Streamlined data capture that speeds inspection cycles The USB Dongle offers a practical route to reduce transcription errors and accelerate inspection procedures by providing a stable wireless link with a range of up to 50 metres. With the option of STANDARD or PRO connectivity, the interface permits simultaneous collection from multiple indicators and gauges, turning otherwise manual logging into automated digital records. This measurable improvement in throughput and traceability supports process control and shortens documentation time for routine quality checks. Plug-and-play integration for Windows-based measurement systems Integration is straightforward: the dongle comes with a 1 m USB extension cable for flexible placement of the receiver at the PC, and it is built specifically for the MDS software on Windows. The device supports common Microtech instrument types such as indicators, calipers, micrometers and bore gauges, enabling a single wireless interface to serve mixed-tool setups. As it operates as a dedicated wireless interface for the Windows environment, configuration focuses on pairing and channel management rather than lengthy driver procedures. Dependable transfer and compatibility for workshop environments Designed for reliable daily use, the interface prioritises secure and interference-resistant transfer to maintain data integrity during measurement routines. Simultaneous connections (3 or 8 channels depending on the variant) allow centralised data logging from several measuring points, which is especially useful where rapid batch checks or multi-station measurement are performed. Note that this dongle is required only for the MDS software on Windows and is not used with iOS, macOS, Android or HID modes, ensuring clarity when selecting the correct integration path. For Windows-based measurement workflows, contact Metav Werkzeuge in Emmerich for expert advice and fast supply of the Microtech USB Dongle tailored to STANDARD or PRO configurations. Technical data Article number: 299190001 GTIN: 4061905048005 Brand: Microtech Metrology ECLASS: 19050110 Category: Data transfer and software Core specifications Wireless range: up to 50 metres STANDARD connection capacity: up to 3 instruments PRO connection capacity: up to 8 instruments Included cable: 1 m MDS USB extension cable Supported host: MDS software on Windows (required) Features and compatibility Stable and secure wireless data transfer Supports indicators, calipers, micrometers and bore gauges Not for use with iOS, macOS, Android apps or HID modes Receiver required only for MDS on Windows FAQ Is the dongle compatible with non‑Windows systems? The dongle is intended solely for use with the MDS application on Windows; it is not used with iOS, macOS or Android versions and does not operate in HID modes. How many instruments can be connected at the same time? Depending on the variant, the STANDARD dongle connects up to 3 instruments while the PRO variant supports up to 8 simultaneous instruments. What measuring devices can be paired with the dongle? The dongle supports Microtech indicators, calipers, micrometers and bore gauges for centralised data collection via MDS on Windows. Is an extension cable included for flexible placement? Yes, a 1 m MDS USB extension cable is included to position the receiver for optimal signal reception at the PC. Manufacturer / Responsible: Microtech, Nizhneyurkovska str., 45a, 04080 Kyiv, Ukraine; tool@microtech.tools
Take advantage of a compact, connected control that combines ZERO setting and reliable data saving with a rechargeable battery for uninterrupted workflows; the robust LED status feedback and choice of one- or two-button operation enable faster, safer capture of measurement points. Order the DataMet FOOTSWITCH Double Touch directly via Metav Werkzeuge or ask our consultants if needed. DataMet FOOTSWITCH Double Touch — multifunction footswitch with Li‑Pol battery and Windows MDS app connectivity (Microtech Metrology) The DataMet FOOTSWITCH Double Touch is a compact control pedal for precision measuring setups, designed to provide zeroing and data transfer to DataMet instruments or the Microtech MDS app on Windows for efficient process integration. Multifunction control for DataMet instruments Zero and save data to instrument or MDS app Built-in rechargeable 500 mAh Li‑Pol battery LED status indicator and compact 120×90×40 mm size Faster, more reliable data capture for measurement workflows The pedal provides direct control over ZERO setting and immediate data storage, reducing the number of manual steps between taking a value and archiving it. By enabling local saving to the instrument memory or synchronisation with the MDS app on Windows, the device shortens cycle times and lowers the risk of transcription errors. The compact footprint (120×90×40 mm) and light weight (0.2 kg) make the unit easy to position at the workstation without obstructing access to the gauge or machine, while the clear LED status indication confirms successful zeroing and data transfer at a glance. Integration and configuration to match production needs Available in single‑button and dual‑button variants, the pedal accepts predefined or custom command mappings for common tasks such as zeroing, triggering measurement capture, and initiating file synchronisation. The built‑in rechargeable Li‑Pol battery (500 mAh) supports continuous use while avoiding loose cables on the floor; recharging is straightforward and the battery specification balances runtime with compact design. For automated data workflows, the footswitch connects seamlessly to Microtech metrology instruments and the MDS app, enabling immediate storage to device memory and later transfer for traceable records. Durable, ergonomic design that supports shop‑floor routines The enclosure and switch layout prioritise repeatable operation and tactile clarity, which reduces operator variability when performing frequent zeroing or save actions. The pedal’s LED status improves operator confidence by signalling connection and battery states without looking away from the workpiece. Custom functions can be specified on request to adapt the pedal to particular measurement sequences or CNC probing setups, turning a simple control into a tailored interface that speeds up inspection loops and minimises handling time. Contact Metav Werkzeuge for tailored configuration or purchase advice on the Microtech DataMet FOOTSWITCH Double Touch and benefit from local stock and application support near your workshop. Technical data Article number: 299900022 SKU: 299900022 Brand: Microtech Metrology Product: DataMet FOOTSWITCH Double Touch Facts Dimensions: 120 × 90 × 40 mm Weight: 0.2 kg Battery capacity: 500 mAh Variants: 1‑button or 2‑button Special features Functions: ZERO and save data to instrument memory or MDS app Connectivity: DataMet instrument link and Windows MDS app synchronisation Indicator: LED status indication Power: Built‑in rechargeable Li‑Pol battery Customisation: Custom functions available on request FAQ How does the footswitch transmit measurement values to software? The pedal saves values directly to the instrument memory or synchronises with the Microtech MDS app on Windows, enabling immediate capture and later export for traceable records. Is there a battery inside and how long does it last? The unit includes a built‑in Li‑Pol battery (500 mAh); the battery supports typical shop‑floor use and is rechargeable to avoid cable clutter. Can the footswitch be used with different DataMet instruments? Yes, the footswitch is designed for connection with DataMet instruments from Microtech Metrology and supports standard save and zero functions. Are there options for different button layouts? Yes, the product is available as a single‑button or dual‑button footswitch, and custom functions can be implemented on request to suit specific measurement workflows. What does the LED status indicate? The LED status reports operational states such as connection, successful zeroing and data save, and battery/charging status for immediate visual feedback. Manufacturer / Responsible: Microtech, Nizhneyurkovska str., 45a, 04080 Kyiv, Ukraine, tool@microtech.tools
Benefit from hands‑free ZEROing and secure data saving combined with a built‑in rechargeable Li‑Pol 500 mAh battery and a compact footprint for uninterrupted, space‑efficient measurement workflows. Order the DataMet FOOTSWITCH One Touch directly via Metav Werkzeuge or consult our specialists for tailored configuration. DataMet FOOTSWITCH One Touch — Multifunction footswitch with Li‑Pol battery for DataMet instruments (Microtech Metrology) The DataMet FOOTSWITCH One Touch is a compact multifunction footswitch designed for hands‑free ZEROing and data saving with Microtech measurement systems and the MICROTECH MDS app for Windows Multifunction for DataMet instruments and MDS app One‑ or two‑button operation with LED status Built‑in rechargeable Li‑Pol 500 mAh battery Compact 60×60×20 mm, weight 0.2 kg Faster, hands‑free data capture to streamline metrology tasks Integrating directly with DataMet instruments and the MICROTECH MDS app for Windows, this footswitch enables reliable, hands‑free ZEROing and immediate data saving to the instrument memory or the PC application. The option of one‑ or two‑button operation reduces handling steps and supports repetitive workflows, which shortens cycle times in quality control and assembly lines. LED status indication gives instant visual confirmation of the command, minimising uncertainty during fast measurement runs and supporting reproducible results in routine inspections. Dependable power and clear status feedback to avoid downtime Equipped with a built‑in rechargeable Li‑Pol 500 mAh battery, the footswitch sustains extended operation and removes the need for frequent battery replacement, helping to keep inspection stations running without interruption. The integrated LED status indication communicates connectivity and save status at a glance, reducing the risk of missed recordings. This combination of rechargeable power and visible feedback contributes to predictable uptime and a calmer workshop environment where measurement data integrity is essential. Space‑saving design suited to bench and portable setups With a compact 60×60×20 mm footprint and a weight of 0.2 kg, the device is unobtrusive on crowded benches and simple to add to portable measurement rigs. The small form factor preserves valuable workspace while ensuring the control remains accessible for operators working at machines or inspection tables. The robust yet compact layout allows straightforward placement next to height gauges, comparators or digital callipers, making it a practical component of any measurement station where ergonomics and tidy routing of cables matter. Customisable control logic that adapts to measurement routines Custom functions are available on request to map the footswitch behaviour precisely to established processes, from simple ZERO commands to synchronised save and read operations in the MDS app. The adaptable one‑ or two‑button configuration supports both single‑step and multi‑function sequences, enabling smoother handover between operator and instrument. By aligning the control logic with the measurement protocol, the footswitch reduces procedure complexity and increases throughput without compromising traceability. Contact Metav Werkzeuge for specification support on Microtech Metrology footswitches; discuss custom functions, integration with DataMet instruments and procurement at Metav Werkzeuge in Emmerich via +49 2822 7131930 or info@metav-werkzeuge.com Technical Data Article number: 299900021 Label: DataMet FOOTSWITCH One Touch Manufacturer: Microtech Metrology Facts Dimensions, mm: 60×60×20 Weight, kg: 0.2 Battery capacity, mAh: 500 Special features Multifunction DataMet footswitch for connection with DataMet MICROTECH instruments and MICROTECH MDS app for Windows Functions: ZERO value and saving data to instrument memory or MDS app Modifications: DataMet 1‑button or 2‑button footswitch LED status indication Built‑in rechargeable Li‑Pol battery Custom functions available on request FAQ How does the footswitch connect to DataMet instruments and the MDS app? The footswitch connects with DataMet instruments and synchronises with the MICROTECH MDS app for Windows to command ZERO and to save measurement data directly to instrument memory or the PC application (SKU 299900021). What is the expected battery behaviour and charging routine? The device uses a built‑in rechargeable Li‑Pol 500 mAh battery; charging restores full functionality and avoids frequent battery replacements, supporting longer continuous use between charges. Can the button layout be adapted for specific measurement processes? Yes — the footswitch is available in one‑button or two‑button configurations and custom functions can be implemented on request to match specific routines and data‑capture sequences. What does the LED status indication show during operation? The LED provides immediate visual confirmation of connectivity and save actions, helping to verify that ZERO or save commands have been executed successfully. Is the footswitch suitable for integration into portable measurement setups? Yes — the compact 60×60×20 mm footprint and 0.2 kg weight make it well suited to both bench‑top and portable measurement arrangements. Manufacturer / Responsible: Microtech, Nizhneyurkovska str., 45a, 04080 Kyiv, Ukraine, tool@microtech.tools
Take advantage of the combination of compact USB connectivity, multi-device support and quick integration for a smoother measurement workflow; the PRO version supports up to 8 simultaneous connections and includes an optional 1 m cable extension for greater installation flexibility. Order the item via Metav Werkzeuge or consult our specialists for compatibility advice and delivery from Emmerich. USB Dongle PRO for Windows — USB connection key with multi-device support (Microtech Metrology) The USB Dongle PRO for Windows provides a dedicated link between Microtech instruments and the MICROTECH MDS app on Windows, enabling stable data transfer and centralised collection of measurement results for workshop and laboratory environments. PRO version: up to 8 connections Designed for MICROTECH MDS on Windows Includes optional 1 m cable extension Boost throughput with reliable multi-device data capture The PRO configuration allows simultaneous connection of up to 8 instruments, which reduces the need for repeated device re-pairing and shortens measurement cycles. By consolidating data streams to a single Windows host, the adapter simplifies logging and traceability processes; this leads to fewer interruptions on production lines and faster reporting. The USB interface provides a deterministic physical link that avoids the variability of wireless pairing, helping to keep automated data collection consistent. Seamless integration into MICROTECH MDS Windows workflows Engineered specifically for the MDS app on Windows, the dongle is optimised for plug-and-play use with Microtech instruments and the related software ecosystem. The PRO and STANDARD variants are distinguished by their connection capacity — PRO for extended multi-device setups, STANDARD for smaller benches — allowing procurement decisions to match the scale of the measurement task. Note that this accessory is intended for the Windows environment and is not requested for iOS, macOS, Android or all HID modes. Practical installation and improved cable reach The package option for a 1 m cable extension provides practical installation freedom when the host PC and measurement bench are separated. A longer cable helps to position the receiver away from heavy electrical interference and to create tidier workstations without compromising signal integrity. Where bench layout or machine placement would otherwise hinder direct USB access, the extension allows a clean, ergonomic setup that supports reliable transfer of measurement data. Efficiency gains for production and quality control Connecting several gauges and indicators simultaneously reduces manual handling and the risk of transcription errors. The dongle supports streamlined data capture for incoming inspection, process-control loops and bench testing, improving throughput while maintaining auditability. Integration with the MICROTECH instrument family ensures measured values are collected centrally, which simplifies statistical analysis and quality reporting across shifts. Proven distribution and support from Metav for professional users Metav supplies the dongle backed by a European distribution channel that emphasises availability and quality control. Sourcing through Metav Werkzeuge brings the advantage of a local stock point in Emmerich and a broad product range that supports workshop standardisation. For buyers seeking a dependable, ready-to-integrate USB connectivity solution, the adapter offers a practical balance of capacity and simplicity while fitting established Microtech workflows. Contact Metav Werkzeuge in Emmerich for a compatibility check, procurement guidance or to arrange immediate supply of the Microtech Metrology USB Dongle PRO for Windows — info@metav-werkzeuge.com • +49 2822 7131930 • WhatsApp +49 170 2837271 Technical data Article number: 299190002 GTIN: 4061905452086 Manufacturer: Microtech Metrology Type: USB Dongle PRO for Windows Facts Maximum connections (PRO): 8 Maximum connections (STANDARD): 3 Cable extension length: 1 m Special features For connection with MICROTECH MDS app on Windows only PRO and STANDARD modifications available Optional 1 m cable extensions for longer reach Not requested for MDS app for iOS, macOS, Android or HID modes FAQ Is the dongle compatible with the MICROTECH MDS app on Windows? Yes. The USB Dongle PRO for Windows is designed specifically to connect Microtech instruments with the MICROTECH MDS app running on Windows systems. How many instruments can be connected at once with the PRO variant? The PRO variant supports up to 8 simultaneous connections; the STANDARD modification supports up to 3 connections. Does the delivery include a cable extension? An optional 1 m cable extension is available and is listed among the product features; check the chosen configuration when ordering. Can the dongle be used with mobile devices or macOS? No. This accessory is intended for the MDS app on Windows and is not requested for iOS, macOS, Android or all HID modes. What identifiers help to order the correct item? Use the article number 299190002 or GTIN 4061905452086 when specifying the USB Dongle PRO for Windows from Microtech Metrology. Manufacturer / Responsible: Microtech, Nizhneyurkovska str., 45a, 04080 Kyiv, Ukraine, tool@microtech.tools
Datenausgabe
Take advantage of a rugged, fully integrated data-collection solution that combines reliable wireless connectivity and broad export options with an all-day battery for uninterrupted shop-floor use. Order directly via Metav Werkzeuge or ask our consultants for configuration and accessories advice. MDS DataMet display unit IP67 — Portable Windows data-collector with touchscreen and sealed housing MDS DataMet display unit IP67 provides a mobile, industry-ready display and data logger for integration with precision measuring instruments, designed for use in production, inspection and laboratory environments. Windows 10 tablet with MDS PRO app IP67 protection for harsh workshop use 10" touchscreen, 1280×800 resolution Export to CSV, XLS and PDF formats Seamless data capture and integration that speeds up inspection cycles The MDS DataMet display unit IP67 acts as a ready-to-run data collection hub, pairing a Windows 10 platform with the MDS PRO app to gather measurements without an intermediate PC. Autoconnection and reading synchronizing reduce manual intervention, while support for multiple wireless links and USB dongles ensures simultaneous communication with many Microtech measuring instruments. The ability to resend to external apps and to export in CSV, XLS and PDF formats enables direct import into Excel, SAP or CAD systems, shortening the time from measurement to documentation and improving process throughput. Rugged portability that keeps quality control on the production floor Built for demanding surroundings, the display unit carries an IP67 rating that protects electronics from dust and temporary immersion, maintaining uptime in wet or dusty environments. The compact 10" touchscreen (1280×800) and a weight of approximately 1.15 kg make the device straightforward to carry between workstations; the internal 8000mAh rechargeable Li‑Pol battery supports extended shifts away from mains power. Physical interfaces such as RS‑232, RJ‑45 and HDMI, plus dual USB ports, ensure compatibility with legacy test rigs and modern networked systems — all packaged in a sealed housing that reduces the risk of environmental-induced failures. Versatile controls and visualisation options for clearer decisions The unit supports practical process-control functions such as Go/NoGo, mm/inch conversion, timer and resolution selection, which help to standardise measurement routines and reduce operator variation. Graphical capabilities — including a Graphical mode and 2D-Graphical mode with PNG export — make trend visualisation and quick pass/fail analysis immediate on the device, aiding rapid decision-making on the shop floor. Optional peripherals such as DataMet buttons, wired or wireless footswitches, and a user manager for role separation extend workflow flexibility and support traceable inspection records. Contact Metav Werkzeuge to configure the Microtech Metrology MDS DataMet display unit IP67 with the options your process requires and to arrange delivery from our Emmerich warehouse, where expert advice and reliable logistics keep production accurate and on schedule. Technical data Article number: 299999003 Touchscreen display: 10" (1280×800) Protection: IP67 Platform: Windows 10 / MDS 5.5 PRO Rechargeable built-in Li‑Pol battery: 8000mAh Dimensions: 280×184×26 mm Weight: 1.15 kg Facts USB‑dongles: 1 (max 2) Wireless: 8 (max 16) Wireless HID: 8 USB HID: 2 USB ports: 2 + 1 WI‑FI: Yes RS‑232: 1 Special features Autoconnection Reading synchronizing User manager Foot‑switch connection (option) Graphical mode; 2D graphical mode; save graph PNG Save data to CSV, XLS, PDF Multilanguage: 10 languages Go/NoGo functions; mm/inch conversion HDMI and RJ‑45 interfaces FAQ What connectivity does the display unit support? The MDS DataMet display unit supports Wi‑Fi, multiple wireless links, USB dongles, RS‑232 and RJ‑45 for flexible connection to instruments and networks. Can measurement files be exported to common office software? Yes — the device exports directly to CSV, XLS and PDF formats, allowing data from the MDS DataMet display unit to be imported into Excel, SAP or CAD systems. Is the unit suitable for harsh workshop environments? With an IP67 rating and a sealed housing, the display unit is designed to tolerate dust and temporary immersion, making it suitable for many workshop and production areas. Are there accessories for hands-free data capture? Optional wired and wireless footswitches and DataMet buttons are available to record measurements and set zero without touching the touchscreen. Manufacturer / Responsible: Microtech, Nizhneyurkovska str., 45a, 04080 Kyiv, Ukraine, tool@microtech.tools
Take advantage of reliable data capture, seamless connectivity and wide export options to streamline quality control and traceability. Benefit from a compact, Windows-based display with touchscreen operation and integrated MDS PRO functionality — order directly via Metav Werkzeuge or consult our specialists for tailored configuration. MDS DataMet Desktop display unit DESKTOP — 11.6-inch touchscreen, Windows 10 data collector (Microtech Metrology) MDS DataMet Desktop display unit DESKTOP provides a ready-to-run, industrial data-collection interface for measurement instruments, ideal for lab benches and inspection stations. 11.6-inch Full HD touchscreen display Windows 10 platform with MDS PRO app Multi-protocol connectivity: USB, RS‑232, RJ‑45 Export to CSV, XLS and PDF plus graphical PNG Faster, more reliable data capture for inspection workflows The MDS DataMet display unit DESKTOP is designed as a dedicated data acquisition terminal for measurement instruments, offering immediate productivity gains through Autoconnection and Reading synchronizing. The device runs on Windows 10 with the MDS PRO app preinstalled, enabling automatic pairing with instruments and consistent capture of values, including zeroing and timestamping. This reduces manual transcription, shortens inspection cycles and improves reproducibility in routine quality checks. Flexible connectivity and open data exchange to fit existing IT A broad set of interfaces ensures smooth integration into existing production IT: USB ports and HID support, RJ‑45 Ethernet, multiple RS‑232 and RS‑485 channels, plus Wi‑Fi for wireless devices. Data may be exported in common formats (CSV, XLS, PDF) and saved as graphical PNG files from the built-in Graphical mode, allowing direct import into Excel, SAP or CAD/packages such as SolidWorks. Format settings (decimal separator, symbols) are adjustable to local standards, simplifying data transfer and traceability. Ergonomic desktop design and optional hands-free operation The unit is compact and lightweight, built for bench use where space is limited; it supports footswitches and optional wireless buttons for hands-free capture, while the onboard User manager, Go/NoGo outputs and mm/inch conversion aid fast decision-making on the shop floor. Multilanguage support and selectable display resolution make adoption straightforward across multilingual teams. These practical features speed up measurement routines and lower the risk of operator-induced variation. For precise, network-capable data collection with Microtech Metrology hardware, contact Metav Werkzeuge in Emmerich for technical advice or to order directly from our stock. Technical data Article number: 299999001 Manufacturer: Microtech Metrology Label: MDS DataMet display unit DESKTOP Platform: Windows 10 / MDS 5.5 PRO Facts Touchscreen: 11.6" (1920 x 1080) Dimensions, mm: 283 x 177 x 73 Weight: 1.25 kg USB port: 4 RJ‑45: Yes RS‑232: 3 RS‑485: 1 USB‑HID: 4 (max 64) Wireless: 8 (max 32) USB‑dongles: 1 (optional 8) Special features Data export: CSV, XLS, PDF Graphical mode and 2D graphical mode, save graph as PNG On-line export to external programmes (Excel, SAP, SolidWorks) Autoconnection and reading synchronizing MDS PRO app and USB dongle PRO included Foot‑switch connection and optional wireless footswitch User manager, Go/NoGo functions, timer and resolution selection mm/inch conversion, multilanguage (10 languages) Cardreader and HDMI output *.xls, *.csv, *.doc file editor and app installation support FAQ What instruments can connect to the display unit? The display unit interfaces with Microtech Metrology instruments and other devices supporting standard protocols; connections available include USB, RS‑232, RS‑485 and wireless HID for seamless data capture. Which file formats are available for export? Export formats supported are CSV, XLS and PDF; graphical outputs can be saved as PNG for reports and visual analysis from the unit. Can the unit transfer data directly into ERP or CAD systems? Yes. The unit supports online export to external programmes such as Excel, SAP and SolidWorks with adjustable data formatting for direct import. Is hands-free data capture possible? Hands-free capture is supported via the footswitch connection; optional wired or wireless footswitches and data‑collect buttons are available for integration. Does the display support multiple users and languages? The unit includes a User manager and offers multilanguage support (10 languages), making it suitable for shared workstations in international environments. Manufacturer / Responsible: Microtech, Nizhneyurkovska str., 45a, 04080 Kyiv, Ukraine, tool@microtech.tools
Software
Benefit from a free Windows application that combines autoconnection with reliable export capabilities to integrate instrument readings quickly into production documentation; the download delivery and support for DataMet and WIRELESS SwissMet connections reduce setup time. Order the software via Metav Werkzeuge or consult our advisors for integration guidance. MicrotechData LITE for Windows — lightweight data-collection software with Autoconnection and Export MicrotechData LITE for Windows is a compact Windows application for collecting and synchronising measurement data from Microtech instruments, designed for straightforward integration into workshop and inspection routines. Free download for Windows 7–11 Autoconnection and device filtering Export to external programs Go/NoGo and mm/inch conversion Faster instrument integration for existing workflows The application brings autoconnection and device filtering to routine measurement tasks, reducing manual steps in data capture. Connecting a single instrument via DataMet or WIRELESS SwissMet is handled automatically, while the support for a USB dongle ensures secure licence handling where required. This approach shortens the route from measurement to stored result, enabling quicker decision cycles on the shop floor and in quality control. Reliable data handling and flexible export options Collected readings are synchronised and can be exported to external programmes, so measurement results become usable immediately in spreadsheets or quality systems. The software supports mm/inch conversion, resolution selection and timed reads, which helps maintain consistent datasets across mixed tooling environments. Export functions minimise transcription errors and speed up reporting, supporting traceability in inspection processes. Simple measurement control and pass/fail logic Integrated Go/NoGo functions and a basic user manager allow the app to act as a first-level quality gate, delivering immediate visual decisions during routine checks. The timer function and selectable resolution aid repeatable sampling, while zero-setting and data read synchronisation ensure that readings reflect the instrument state at the moment of capture. These controls make it easier to standardise short inspection routines without complex setup. Low barrier to entry and practical deployment Delivered via direct download and provided as a free edition, the software requires minimal infrastructure to begin operation. Support for Windows 7–11 and a single-instrument connection model keeps resource needs modest, making this solution suitable for workshops and small inspection stations that need dependable digital capture without heavy IT overhead. The lightweight footprint and straightforward configuration reduce disruption during roll-out. Contact Metav Werkzeuge for tailored advice on integrating MicrotechData LITE into existing measurement systems or to obtain the download link and configuration support Technical Data SKU: 299100530 GTIN: 4061905452055 Platform: Windows 7, 8, 10, 11 Delivery: Download Facts Max. instruments connected: 1 USB dongles (max qty): 1 Special features MDS app for Windows for connection with Microtech instruments Data collection from instruments and zero setting Autoconnection and connection modes Filtering MICROTECH devices mm/inch conversion Go/NoGo functions Timer and resolution selection Export to external programs User manager Instruments connection: DataMet / WIRELESS SwissMet Licence: Free FAQ Is MicrotechData LITE compatible with older Windows versions? MicrotechData LITE supports Windows 7, 8, 10 and 11 as listed, so the application can be installed on legacy and current desktop systems when meeting basic system requirements. Can multiple instruments be connected simultaneously? The LITE edition is configured for a single instrument connection; for multi‑instrument workflows, consider higher-tier solutions or contact Metav Werkzeuge for options. Which connection types are supported for data transfer? Supported connection modes include DataMet and WIRELESS SwissMet; the software handles autoconnection and device filtering to simplify pairing with Microtech hardware. How are measurement units and resolution handled? MicrotechData LITE provides mm/inch conversion and selectable resolution, enabling consistent output for mixed-unit environments and ensuring results match inspection tolerances. Is the software supplied with a commercial licence or is it free to use? This edition is delivered as a free download (SKU 299100530) for Windows deployment; distribution and licence details are provided at download. Manufacturer / Responsible: Microtech, Nizhneyurkovska str., 45a, 04080 Kyiv, Ukraine, tool@microtech.tools
Take advantage of a centralised measurement workflow and reliable export options to eliminate manual transcription and speed up quality routines; combine autoconnection, multi-instrument support and flexible export formats for a smoother production flow. Order the software directly via Metav Werkzeuge or ask our consultants for integration advice. Optima App Microtech for Windows — measurement data collection and export software, multiconnect support Optima App Microtech for Windows is a Windows-based application designed to collect, synchronise and export measurement data from Microtech instruments for shop-floor and laboratory use. Centralised data collection and export Connect up to 8 instruments simultaneously Exports to CSV, XLS and PDF formats Autoconnection and mm/inch conversion Streamline measurement routines with centralised data handling The software provides a centralised data-collection backbone that removes repetitive data entry and reduces transcription errors. By automatically detecting connected instruments and offering autoconnection and synchronised data reading, the application shortens cycle times and improves throughput. The built-in zero-setting and device filtering preserve traceability while the user manager allows role-based operation on a single PC, making the system suitable for routine quality checks as well as small-scale production environments. Export to common systems and secure process documentation Designed for interoperability, the solution supports on-line export to external programmes such as Excel, SAP and SolidWorks and saves results in csv, xls and pdf formats. Export settings are adjustable (dot/comma, symbols) to match regional conventions, and graphical output can be saved as PNG for reports. These capabilities enable straightforward archival of measurement series and faster transfer into SPC workflows, ensuring measurement results feed directly into downstream analysis without additional conversion steps. Flexible connectivity and ergonomic operation at the bench Installation on Windows 7–11 enables immediate use on standard workshop PCs. The app supports up to eight instruments simultaneously and accepts up to two USB dongles for wireless connectivity. Optional footswitch and button integration (USB or WIRELESS) allows hands-free data capture and zero setting, speeding up repetitive measurements. The combination of wired and wireless modes, together with mm/inch conversion and Go/NoGo functions, makes the setup adaptable to varied measurement tasks on the shop floor. Clear visualisation and configurable measurement workflows A graphical mode and timer simplify the interpretation of measurement sequences, while resolution selection helps tailor data precision to the task. The software also includes energy-saving and filtering modes to keep operations efficient and focused on recognised Microtech instruments. Multilanguage support broadens usability across international teams and the capability to save graphs and structured data streamlines documentation, helping to integrate small workshops into more disciplined quality systems. Discuss integration and licensing with Metav Werkzeuge to ensure seamless connection to existing measurement equipment and production software — our specialists in Emmerich can advise on deployment scenarios and compatibility Technical data Article number: 299100560 Product name: Optima App Microtech for Windows Platform: Windows 7, Windows 8, Windows 10, Windows 11 Manufacturer brand: Microtech Metrology Core numerical data Max. instruments connected: 8 USB-dongles (max qty): 2 Languages supported: 10 Special features MDS app for Windows for connection with Microtech instruments Collecting data from Microtech instruments and zero setting Autoconnection and data reading synchronising On-line export to external programmes (Excel, SAP, SolidWorks) Data export formats: csv, pdf, xls Export format adjustable (dot/comma, symbols) Optional DataMet buttons and footswitch (USB / WIRELESS) Filtering Microtech devices and user manager mm/inch conversion and Go/NoGo functions Graphical mode, timer and resolution selection Save graph as PNG and export data to external programmes Standard / energy saving mode FAQ Which Windows versions are supported? The Optima App Microtech for Windows supports Windows 7, 8, 10 and 11 and is intended for installation on standard shop‑floor or laboratory PCs. How many instruments can be connected at the same time? Connection of up to eight instruments is supported; the software also allows up to two USB dongles for wireless links to Microtech Metrology devices. In which formats can measurement data be exported? Measurement results can be saved and exported as csv, xls and pdf files; graphical output may be saved as PNG for inclusion in reports. Can the app integrate with ERP or CAD systems? Yes — the app offers on-line export to external programmes such as Excel, SAP and SolidWorks with adjustable data formatting to match downstream systems. Are hands-free controls available for faster acquisition? Optional footswitch and button support (USB and wireless) enable hands-free data capture and zero setting to accelerate repetitive measurements. Manufacturer / Responsible: Microtech, Nizhneyurkovska str., 45a, 04080 Kyiv, Ukraine; tool@microtech.tools
Take advantage of the combination of Windows compatibility, autoconnection with instrument ZERO setting, and flexible export to CSV, XLS and PDF for a dependable, auditable data flow in the metrology workflow. Order the MicrotechData software directly via Metav Werkzeuge or ask our consultants for tailored integration advice. MicrotechData — data acquisition software for Windows, USB-stick format, Microtech Metrology MicrotechData is a compact Windows application for synchronised data collection from Microtech measurement instruments, optimised for integration into production and quality‑control environments. Windows 7–11 compatible software Connects up to 3 instruments Export to CSV, XLS and PDF Autoconnection and zero setting Seamless capture for consistent measurement records The software provides synchronised data capture across connected instruments, ensuring measurement values are recorded with consistent timing and format. Installed from the supplied USB‑stick, the application supports standard and energy‑saving modes and can maintain a persistent autoconnection to devices. This reduces manual steps during inspection rounds and helps to prevent transcription errors, which in turn streamlines traceability and auditability within the quality process. Ready integration with existing systems and workflows Export functionality is designed for practical compatibility: data can be saved as CSV, XLS or PDF, and formats are adjustable for decimal separators and symbol conventions to match enterprise systems. On‑line export to external programmes such as SAP or SolidWorks is supported, enabling direct transfer of measurement results into documentation or CAD‑linked inspection routines. The ability to choose resolution, convert mm/inch, and use Go/NoGo evaluation reduces follow‑up processing and accelerates decision cycles on the shop floor. Practical controls that support operator efficiency Operator features include a user manager, device filtering, and support for both WIRELESS and USB foot‑switch and button connections, which facilitate hands‑free capture during repetitive measurements. An instrument ZERO setting for DataMet devices and built‑in timers assist consistent measuring sequences, while the Go/NoGo and resolution options allow simplified pass/fail assessments. These functions together help to lower operator variability and increase repeatability in routine checks. Deployment flexibility and device compatibility The application runs on Windows 7, 8, 10 and 11 and supports connection to up to three instruments simultaneously with a single USB dongle permitted. Filtering of Microtech devices and automatic data synchronisation reduce setup time in mixed‑instrument fleets. Multilanguage support (ten languages) and the option to export in common file types make the tool suitable for international teams and for integration into central data processes. The MDS app features enable remote connection modes and zero setting, providing a compact solution for small to medium measurement stations. Contact Metav Werkzeuge in Emmerich for licensing, deployment options and integration support — email info@metav-werkzeuge.com or call +49 2822 7131930 to discuss how MicrotechData can be configured for specific measurement setups Technical Data Article number: 299100550 GTIN: 4061905452062 Format: USB‑stick Platform: Windows 7, 8, 10, 11 Facts Max. instruments connected: 3 USB‑dongles (max qty): 1 Multilanguage: 10 languages Special features MDS app for Windows for connection with Microtech instruments Autoconnection and data reading synchronising Instrument ZERO setting (DataMet) Online export to external programmes (e.g., SAP, SolidWorks) Export formats adjustable (dot/comma, symbols) Save data to CSV, XLS, PDF mm/inch conversion and Go/NoGo functions Timer and resolution selection User manager and device filtering WIRELESS and USB foot‑switch/button support FAQ What operating systems does the software support? The application runs on Windows 7, 8, 10 and 11 and is supplied on a USB‑stick for convenient installation. How many instruments can be connected at the same time? MicrotechData supports connection of up to three Microtech instruments simultaneously. Which export formats are available for measurement data? Measurement results can be exported to CSV, XLS and PDF, with adjustable decimal separators and symbol settings for seamless import into enterprise systems. Is there support for hands‑free measurement capture? Yes — the software accepts both WIRELESS and USB foot‑switch and button connections to enable hands‑free data capture. Can exported data be sent directly to ERP or CAD systems? On‑line export to external programmes such as SAP and SolidWorks is supported; format settings help to match the receiving system. Manufacturer / Responsible: Microtech, Nizhneyurkovska str., 45a, 04080 Kyiv, Ukraine, tool@microtech.tools
Take advantage of high‑throughput data collection, reliable autoconnection and flexible export options for a streamlined quality workflow; order the licence and USB‑stick delivery directly via Metav Werkzeuge or consult our specialists for compatibility advice. MicrotechData PRO for Windows — PC data‑collection software with multi‑instrument support and export to CSV/XLS/PDF (Microtech Metrology) The MicrotechData PRO for Windows is a Windows‑based data‑management application designed for metrology and production quality control, providing synchronised capture from Microtech instruments and Wireless SwissMet devices for centralised logging and evaluation. Supports up to 48 instruments simultaneously Export to CSV, XLS and PDF formats Graphical and 2D graphical display modes Autoconnection with device filtering Supplied on USB stick for quick deployment Centralised, high‑speed data collection to keep inspection moving The PRO version delivers a robust solution for batch testing and serial inspections by enabling simultaneous connection to multiple measuring devices. Built for measured throughput, MicrotechData PRO for Windows supports up to 48 instruments, with automatic device detection and synchronised reading to prevent manual transcription errors. The software’s autoconnection and user manager reduce setup time, while Go/NoGo and resolution selection simplify pass/fail decisions at the workbench, improving traceability and reducing rework in production. Seamless export and integration into enterprise systems Data export is a core capability: the application produces CSV, XLS and PDF outputs and permits online export to external systems such as Excel, SAP and SolidWorks. Export formats are adjustable (dot/comma, symbol settings) to match regional conventions, aiding downstream processing and automated reporting. The option to save graphical results as PNG files and to export structured CSV/XLS enables quick import into SPC tools or batch reporting routines, delivering a measurable time‑saving across audit and documentation tasks. Flexible interfaces and workflow enhancements for the shop floor Interfacing is catered for via wired and wireless modes: connections support DataMet and WIRELESS SwissMet devices, and the package accepts optional DataMet Buttons and footswitches for hands‑free capture. A USB‑dongle is required for licensing and security, with a maximum of 10 dongles supported in larger deployments. These hardware options allow workstations to remain lean while operators focus on measurement tasks; the combination of device filtering and autoconnection makes the system tolerant to mixed instrument fleets and changing test setups. Practical deployment, multilingual support and platform compatibility Installation and rollout are straightforward: the PRO edition is supplied on a USB stick and runs under Windows 7, 8, 10, 11, while a free version is available for evaluation. The application includes a graphical mode and a 2D graphical mode for trend analysis, mm/inch conversion, timers and a selection of resolutions to match inspection criteria. Multilanguage support (10 languages) and a configurable data format help integrate the software across international teams, ensuring consistent results and easing operator training. Contact Metav Werkzeuge today to discuss MicrotechData PRO for Windows licence delivery on USB stick, verify instrument compatibility for your inspection benches, or to request a tailored deployment plan. Technical Data Article number: 299100570 GTIN: 4061905452079 Format: USB‑stick Platform: Windows 7, 8, 10, 11 Facts Max. instruments connected: 48 USB‑dongles (max qty): 10 Multilanguage: 10 languages Special features MDS app for Windows for connection with Microtech instruments DataMet and WIRELESS SwissMet connection modes Instrument ZERO setting (DataMet) Autoconnection and device filtering Data reading synchronising On‑line export to external programs (Excel, SAP, SolidWorks) Export formats: csv, xls, pdf Graphical mode and 2D‑graphical mode Save graph as PNG Data format adjustable (dot/comma, symbols) Timer and resolution selection Go/NoGo functions mm/inch conversion User manager Optional DataMet Buttons and footswitch (wireless and USB) Free version downloadable; Standard, Optima & PRO supplied on USB stick USB‑dongle required for licence activation FAQ Which Windows versions are supported? The software supports Windows 7, 8, 10 and 11 as indicated for MicrotechData PRO for Windows. How many instruments can be connected at once? MicrotechData PRO for Windows can connect up to 48 instruments simultaneously in the PRO configuration. What export formats are available for further analysis? Exports from MicrotechData PRO for Windows include CSV, XLS and PDF; graphs can be saved as PNG for embedding into reports. Is a hardware dongle required for operation? A USB‑dongle is required for licence activation; deployment scenarios may use up to 10 dongles across multiple stations. Can the software interface with ERP or CAD systems? Yes — the product supports online export to external programmes including Excel, SAP and SolidWorks for seamless data transfer and automation. Manufacturer / Responsible: Microtech, Nizhneyurkovska str., 45a, 04080 Kyiv, Ukraine; tool@microtech.tools