Twist Drill Bits for Professionals: Quality You Can Rely On

Twist Drill – Left-Cutting HSS-G Twist Drill (Ø 1.5 mm, 135° Tip, DIN 338) The Twist Drill left-cutting bit for drilling machines, designed for precise metalworking and for tasks such as removing broken or seized screws. Left-cutting geometry for extracting screws 135° tip for hard materials and stainless steel HSS‑G material for high wear resistance Conforms to DIN 338 for short shank drills Optimised for drilling machines with left rotation Faster metalworking with reduced feed forces The Twist Drill with left‑cutting geometry is engineered for efficient metalworking. Its specialised grind allows cutting in left rotation, which is particularly helpful when extracting broken or seized screws. Compared with standard HSS bits, the sharpened design can achieve up to 40% faster drilling while requiring about 50% less feed force, making machining less strenuous on both operator and machine. Precision entry and less wandering on tough materials A 135° Tip is selected to improve centring and reduce walking on hard materials such as stainless steel. The larger tip angle shortens the initial penetration time and produces a more controlled cut, which is advantageous when working with thicker or tougher alloys. For operators, this means cleaner holes and less need for pilot operations. Durable HSS‑G composition and standardised manufacture Made from HSS‑G, this bit combines high-speed steel hardness with good toughness for repeated use in metalworking. Compliance with DIN 338 ensures consistent dimensions and quality for short shank, cylindrical Twist Drills, so replacement and inventory management are straightforward. For non-experts: DIN 338 describes the geometry and production methods commonly used for short metal drills, ensuring interchangeability across suppliers. Application range and machine compatibility Designed for drilling in a range of metals including alloyed and unalloyed steels, cast steel, and non-ferrous metals, this left‑cutting Twist Drill performs best in a drilling machine that can run in left rotation. Typical uses include general metal fabrication and specialised tasks like out‑drilling screw remains. Operators needing clean, repeatable results from metal to hard plastics will find this bit reliable and robust. Strongly recommended for professionals and workshops requiring a left‑cutting high‑performance Twist Drill from MetavCUT — for technical advice or to confirm suitability for specific applications contact METAV Werkzeuge; Email: info@metav-werkzeuge.com; Phone: +49 2822 7131930; WhatsApp: +49 170 2837271 Twist Drill Brand: MetavCUT SKU: 60015-FDA Diameter: 1.5 mm Tip angle: 135° Execution: Left-cutting For: Drilling machine (left rotation required) Material: HSS‑G Norm: DIN 338 Model series: Profi Line Application: Drills for metal Designation: Twist Drill (short shank, cylindrical) Hersteller: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What are Twist Drills used for? Twist Drills from MetavCUT are primarily applied to machining high-strength workpieces and larger drill diameters; their design is easy to re‑grind and withstands higher loads, making them suitable for tasks such as drilling alloyed and unalloyed steel, cast materials and hard plastics. Which three drill types are there? The main drill categories are: Metal drills, Wood drills and Stone/Concrete drills; the MetavCUT Twist Drill belongs to the metal drill family and is optimised for metallic materials. Can the MetavCUT Twist Drill be used to remove broken screws? Yes, the left‑cutting MetavCUT Twist Drill is designed for applications including extracting broken or seized screws because the left rotation often helps engage and loosen a screw remnant while drilling.

Twist Drill — Type N Short HSS-G Drill Bit, 1.5 mm, 135°, Bright Finished, DIN 338 (MetavCUT) The Twist Drill is a short Type N drill bit designed for precision metal drilling on Drilling Machines and workshop hand drills. Short Type N design for stable drilling in metal HSS-G ground for up to 40% faster drilling 135° tip angle for harder materials like stainless steel Fully ground shank for precise centring in chucks Conforms to DIN 338 for short twist drills High precision for demanding metalwork The short Twist Drill in HSS-G material combines a compact geometry with a 135° Tip Angle to improve stability when penetrating hard materials. The reduced free length minimises deflection and vibration, which increases hole accuracy in Steel and Cast components. Conformity with DIN 338 ensures the bit matches standard dimensions and tolerances for short twist drills, facilitating reproducible results in production and repair tasks. Faster results with lower feed force Thanks to the specially ground geometry of the HSS-G grade, drilling speeds can be increased while required feed force is reduced, delivering measurable productivity benefits. The fully ground flute and point geometry are optimised to lower friction and chip resistance, which means less operator effort and improved cycle times when processing alloyed and unalloyed Steel, Cast Iron and non-ferrous Metals. Reliable compatibility with machines and chucks The short Execution and a Fully Ground Shank support secure clamping in hand and machine chucks, while the Overall Length of 40 mm and Spiral Length of 18 mm make the bit suitable for tight working spaces. A Bright Finished surface offers corrosion resistance during storage and easier handling. This design favours repeatable centring and consistent surface finish when used in rotating stationary or portable drilling equipment. Expert advice and safe application For precision tasks and challenging materials, correct speeds, feeds and coolant selection matter. METAV Werkzeuge and the manufacturer MetavCUT provide competent technical advice if application-specific data are required. If uncertain whether this tool meets your requirements or whether machine setup is optimal, contact METAV Werkzeuge for detailed guidance by email or phone—support is available for workshop planning and drill selection to maximise tool life and hole quality. Strong recommendation: Choose the MetavCUT HSS-G short Twist Drill for demanding metal drilling and consult METAV Werkzeuge for tailored technical support via info@metav-werkzeuge.com or +49 2822 7131930 Technical data Designation: Twist Drill Marke: MetavCUT SKU: 27015-FDA Type: Type N Diameter: 1.5 mm Tip angle: 135° Material: HSS-G Norm: DIN 338 Execution: short Overall length: 40 mm Spiral length: 18 mm Shaft finish: fully ground Colour: bright finished Intended for: Drilling Machine / Hand Drills Model series: Basic Line Applications: Drills for Metal Manufacturer: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What is the Twist Drill (MetavCUT, Type N) mainly used for? The Twist Drill by MetavCUT in Type N execution is primarily applied to the machining of high-strength materials and larger hole diameters; its shape is easy to regrind and it withstands considerable loads while providing reliable performance in Steel and Cast applications. Which three drill types exist? Commonly distinguished drill types are Metal Drill (for Steel and alloys), Wood Drill and Masonry/Concrete Drill; the MetavCUT Type N Twist Drill falls into the Metal Drill category and is optimised for such tasks. Why are Twist Drills sharpened (pointed)? The sharpening reduces the cross-cut at the tip, which significantly lowers friction and thus the required feed force; a well-pointed Twist Drill (MetavCUT Type N) also centres more reliably in the workpiece for cleaner entries. Can a metal drill be used in wood? A Metal Drill such as the MetavCUT Type N Twist Drill can be used in Wood, but guidance and finish are typically inferior compared with a dedicated Wood Drill; metallic bits are easier to resharpen and show less self-feed in softer materials. At what drilling depths is the Twist Drill most used? A through-hole in solid material is usually executed with a Twist Drill; for diameters up to about 20 mm and drilling depths up to 100 mm, the short or standard Twist Drill is the most frequently used tool. Which is better, HSS or HSSE? The general assumption that HSSE is always superior to HSS is not universally correct; the MetavCUT HSS-G selection should be evaluated against actual working conditions to determine whether the additional cost of HSSE is justified.

Twist Drill — HSS-G Short Twist Drill, Ø 1.5 mm, 118° (Type N), Bright Finished by MetavCUT The Twist Drill (Type N) is a short HSS-G metalworking drill with a 1.5 mm diameter and a 118° tip angle, optimised for precise drilling in metals using a Drilling Machine. Short HSS-G design for increased rigidity DIN 338 standard for short twist drills 118° tip for reliable centring in metals Fully ground shank for precise runout Ideal for use in Drilling Machine applications Precision drilling with reduced deflection for consistent holes The short design of this HSS-G twist drill reduces overhang and therefore minimises bending and vibration during machining, which leads to more consistent hole geometry and longer tool life. The combination of short length and fully ground geometry provides higher stiffness compared with standard-length drills, so less radial runout occurs when used in a Drilling Machine. As a result, operators benefit from improved hole quality and fewer rejects when working with steels, cast iron and non-ferrous metals. Sharp ground geometry that gives clean, accurate bores A fully ground flute geometry produces very sharp cutting edges and excellent concentricity. Grinding (HSS‑G) yields a high degree of roundness and a clean cutting action, which is especially valuable for demanding metalworking tasks. The 118° tip offers a compromise between fast penetration and reliable centring; it is commonly used for general metalwork and gives easier entry on slightly curved surfaces. Note that ground drills tend to be sharper but require appropriate coolant and moderate feed to avoid brittle fracture during heavy interrupted cuts. Target users and typical applications for best results This short Type N twist drill is designed for professional workshops, toolrooms and industrial maintenance where precise, repeatable metal drilling is required. It suits machining of alloyed and unalloyed steel, cast and sintered irons, non‑ferrous metals and hard plastics. The product is particularly useful when working on bench and floor Drilling Machines or when minimal runout is essential for subsequent reaming or tapping operations, delivering reliability for quality‑focused tradespeople. Practical guidance to maximise performance and service life Use cutting fluid or internal/external cooling when drilling steels and hard materials to reduce temperature and preserve cutting edges. Secure the workpiece and avoid excessive overhang from the chuck; the short geometry already reduces deflection, but correct clamping and moderate feed rates ensure best results. If drilling softer materials such as aluminium, adapt speed and lubrication to avoid built‑up edge. Remember that the Type N spiral is a general‑purpose metal geometry and may not be ideal for specialised wood or masonry work. Strong recommendation: For precision metal drilling choose the MetavCUT short HSS‑G Twist Drill (Type N) — for technical questions or personalised advice METAV Werkzeuge provides comprehensive support via info@metav-werkzeuge.com, Tel +49 2822 7131930 or WhatsApp +49 170 2837271 Technical information Designation: Twist Drill Brand: MetavCUT SKU: 48015-FDA Type: Type N Material: HSS-G Norm: DIN 338 Diameter: 1.5 mm Tip angle: 118° Overall length: 40 mm Spiral length: 18 mm Execution: short Colour: bright finished Shank finish: fully ground Intended for: Drilling Machine Application: Drills for metal Manufacturer: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What are Twist Drills used for with the MetavCUT Type N Twist Drill? The MetavCUT Twist Drill Type N is used primarily for machining high‑strength materials and larger drill diameters; its short configuration lends itself to precise metalworking operations. The geometry is relatively easy to re‑grind and holds up under considerable loads, making it suitable for demanding workshop tasks. Which three drill types exist and how does the MetavCUT Twist Drill fit in? There are three common drill families: metal drills, wood drills and stone/concrete drills. The MetavCUT Twist Drill belongs to the metal drill category (Type N), optimised for steel and ironwork rather than masonry or specialised timber boring. Can Twist Drills be used for wood? Metal drills such as the MetavCUT Twist Drill can be used in wood but they provide less guidance and a rougher finish than dedicated wood bits. They are easier to resharpen and have lower self‑feeding tendency, but for best results in timber a purpose‑designed wood drill is recommended.

MetavCUT Twist Drill (Short) — Twist Drill, HSS-G, 1.5 mm, TIN-coated, 118° tip, DIN 338 The Twist Drill (Short) from MetavCUT is a precision HSS-G drill intended for metalworking on drilling machines and hand drills, combining a short, rigid design with TIN coating for longer life and reliable centring. MetavCUT Twist Drill Short 1.5 mm diameter TIN-coated for extended tool life Fully ground shank for precise runout DIN 338 compliant short design for metal Up to 40% faster drilling with lower thrust Precise Metalworking with Reduced Runout and Better Control Designed for demanding metal applications, the Twist Drill offers a 1.5 mm cutting diameter and a fully ground shank that improves concentricity and reduces runout. This results in cleaner holes and more consistent fits when working with steels and non-ferrous metals. Users benefit from the increased accuracy when performing repetitive or precision drilling tasks on stationary or portable drilling machines. Short Design for Greater Stability and Faster Results A shorter overall length significantly reduces the unsupported overhang, improving stability and minimising bending. The short configuration enhances stability and precision, making the tool especially suitable for drilling hard materials where deflection would otherwise compromise hole quality. For workshop setups that require tight tolerances, the compact geometry helps achieve faster cycle times without sacrificing control. Durable Construction: HSS-G Material and TIN Coating Explained Manufactured from HSS-G (ground high-speed steel) and finished with a TIN-coated surface, this Twist Drill combines sharp cutting edges with a low-friction layer. HSS-G means the flutes and geometry are produced by grinding, yielding very sharp edges and high concentric accuracy. The Titanium Nitride coating reduces friction and wear under proper cooling, extending tool life during serial metal drilling operations and lowering the risk of premature dulling. Practical Application Tips and Suitable Materials With a 118° tip angle, the drill offers easier centring on slightly curved or coated surfaces and works well in softer to medium-hard materials; combined with the short design it is also effective in steels and cast materials when appropriate coolant is applied. For best results in alloyed or unalloyed steels, use steady feed, proper clamping and coolant. The tool complies with DIN 338, indicating it meets standard dimensions and tolerances for short twist drills with cylindrical shanks. We recommend the MetavCUT Twist Drill Short for precision metal drilling — for expert technical advice, suitability checks or ordering assistance contact METAV Werkzeuge: 📧 info@metav-werkzeuge.com ☎️ +49 2822 7131930 ✔️ WhatsApp +49 170 2837271 — METAV Werkzeuge provides comprehensive and competent consultation to ensure this tool meets your requirements Designation: Twist Drill (Short) Brand: MetavCUT SKU: 28015-FDA Diameter: 1.5 mm Spiral Length: 18 mm Overall Length: 40 mm Tip Angle: 118° Material: HSS-G (ground high-speed steel) Coating: TIN-coated (Titanium Nitride) Shank Finish: Fully ground Execution: Short Applicable Machine: Drilling Machine / Hand Drill Norm: DIN 338 Model Series: Basic Line Colour: TIN-coated Application: Drills for metal Hersteller: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What materials is the MetavCUT Twist Drill suitable for? The MetavCUT Twist Drill (Short) is intended primarily for metalworking and performs well in alloyed and unalloyed steel, Tempered Cast Iron, Cast Iron, Sintered Iron, Copper Alloys, Bronze and certain Hard Plastics when used with appropriate coolant and machine settings. For what is a Twist Drill used? A Twist Drill is mainly used for machining high-strength materials and larger hole diameters; its ground geometry is easy to re-sharpen and resists higher loads, making it suitable for demanding metalworking tasks while maintaining good centring and durability. Which three drill types exist? There are three common drill types: Metal drills, Wood drills, and Masonry/Concrete (Stone) drills. Why are Twist Drills sharpened? The sharpening reduces the secondary cutting edge at the tip, which lowers friction and therefore the required feed force; sharpening also improves centring, so the MetavCUT Twist Drill achieves more accurate starts and smoother cutting in the workpiece.

Twist Drill (Type N) – Short, 1.5 mm, 118°, TiN-coated, HSS‑G, DIN 338 by MetavCUT A Twist Drill (Type N) designed for precise metalworking, offering a short, stable design and TiN coating for extended tool life. Short HSS‑G design for improved stability TiN-coated for reduced wear and longer life Fully ground shank for faster, cleaner drilling 118° point angle suited to softer metals and centring Conforms to DIN 338 for reliable manufacturing quality Stable holes with less deflection for precision metalwork The short HSS‑G construction reduces overhang and significantly increases Stability during drilling, which helps to avoid chatter and bending. Because the Flute Geometry is produced by CNC grinding, the cutting edges are exceptionally sharp and ensure clean chip evacuation. This results in a Precision improvement for demanding tasks such as drilling in Steel, Cast Iron or Copper alloys. For stationary machines and bench work, the shorter Projection enables more controllable feed and better repeatability. Faster cutting with lower feed forces thanks to grinding A fully ground Shank and flute geometry enable up to 40% faster drilling speeds while requiring substantially less axial force compared with rolled alternatives. The TiN Coating reduces friction and thermal wear, meaning longer service life under continuous use when combined with appropriate cooling. This advantage translates into higher throughput and lower tool-change frequency, which is particularly valuable in production environments and professional workshops. Versatile application spectrum and material compatibility Engineered as a Type N normal-spiral drill, this short variant is well suited to general metalworking tasks. It performs reliably in alloyed and unalloyed Steel, Tempered Cast, Cast Iron, non‑ferrous Metals like Copper and Bronze, and even hard plastics. The 118° point angle assists centring on slightly curved surfaces and is often preferred when a balance between fast penetration and clean hole finish is required. Practical considerations for safe, efficient use For optimal results, use appropriate cutting fluid or coolant when machining metals to lower temperatures and extend life. The shortened length reduces the risk of breakage under lateral loads, but because ground drills can be relatively brittle, firm clamping and steady feeds are recommended. When high precision is required, the reduced runout of a ground Twist Drill helps deliver consistent diameters and better surface quality. Who benefits from this design Workshop professionals, tool rooms and precision fabricators profit most from the shorter TiN‑coated HSS‑G solution: where repeatable hole quality, tool life and machining speed matter. The product is designed to meet industrial expectations for durability and consistency while remaining easy to integrate into standard Drilling Machines and production routines. Strong recommendation: Choose the MetavCUT short TiN‑coated HSS‑G Twist Drill for precision metal applications — for further technical advice or to confirm suitability for specific tasks, contact METAV Werkzeuge’s competent support team at info@metav-werkzeuge.com or call +49 2822 7131930; WhatsApp +49 170 2837271 Technical Data Designation: Twist Drill / Short Spiralbohrer Brand: MetavCUT SKU: 46015-FDA Diameter: 1.5 mm Overall length: 40 mm Spiral length: 18 mm Point angle: 118° Type: Type N Execution: Short Coating/Colour: TiN-coated Shank execution: Fully ground Material: HSS-G Norm: DIN 338 Application: Drills for Metal / For Use in Drilling Machine Model series: Standard Line Hersteller: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ For what is the Twist Drill mainly used? The MetavCUT Twist Drill (Type N) is primarily used for machining high‑strength materials and larger drill diameters; its short design and TiN coating make it suitable for precise operations in alloyed and unalloyed Steel, Cast Iron and non‑ferrous metals. This geometry is easy to re‑grind and withstands higher loads. Which three drill types exist? Commonly distinguished drill types are Metal Drills, Wood Drills and Stone/Concrete Drills; the MetavCUT Twist Drill belongs to the metal drill category and is optimised for a wide range of metallic materials.

Twist Drill — Short Type N, 1.5 mm, 118° Tip, TiN-coated, HSS-G, DIN 338 (MetavCUT) The Twist Drill short Type N is a compact HSS-G metalworking drill for Drilling Machines, designed for stable, precise holes in a wide range of metals. Short Twist Drill design for enhanced stability HSS-G material for high wear resistance TiN-coated surface reduces friction and wear Fully ground shank for precise concentricity DIN 338 standard for metalworking reliability High performance through material and coating Engineered for demanding metalworking, this Twist Drill uses HSS-G (ground high-speed steel) to combine hardness and sharpness. The TiN-coated surface reduces friction and heat generation, which extends tool life and lowers wear during continuous operation. Compliance with DIN 338 assures consistent manufacturing tolerances and suitability for both stationary and portable drilling equipment. These material choices enable reliable results and predictable tool replacement cycles. Precision and reduced runout for cleaner holes A short overall length and a fully ground geometry minimise overhang and bending, which results in better concentricity and less radial runout. The 118° tip angle offers easier centring on curved or slightly uneven surfaces and is suited to a variety of metallic materials. With a spiral length of 18 mm and an overall length of 40 mm, the drill delivers controlled chip evacuation and stable cutting action, especially where tight tolerances and clean hole walls are required. Faster drilling with lower effort Compared with conventional HSS variants, the ground HSS design enables up to 40% faster drilling while requiring about 50% less axial force under suitable conditions. Reduced friction from the TiN coating further lowers cutting temperatures and tool wear. For best results in tougher alloys, use appropriate cutting speeds, lubrication or coolant and secure clamping; this drill is intended primarily for metal applications on compatible Drilling Machines. Tailored for metalworking professionals and workshops Designed as a Type N “normal spiral” twist drill, this short version excels in machining alloyed and unalloyed steel, cast iron, copper, bronze, sintered iron and hard plastics. The combination of short reach and robust HSS-G material makes it a practical choice for toolrooms, maintenance departments and metal fabrication shops that prioritise precision and tool longevity. MetavCUT’s Profi Line emphasises repeatability and serviceability in industrial environments. Strongly recommend selecting the MetavCUT Twist Drill short Type N for precise metal drilling — for detailed advice or additional technical data contact METAV Werkzeuge: info@metav-werkzeuge.com | +49 2822 7131930 | WhatsApp +49 170 2837271 Technical Information Designation: Twist Drill (Short) Brand: MetavCUT SKU: 41015-FDA Diameter: 1.5 mm Spiral length: 18 mm Overall length: 40 mm Point angle: 118° Type: Type N Material: HSS-G Coating: TiN-coated Shank execution: Fully ground Execution: Short For machine: Drilling Machine Application: Drills for metal Norm: DIN 338 Model series: Profi Line Hersteller: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What are Twist Drills used for? Twist Drills from MetavCUT, specifically the short Type N metal drill, are mainly used for machining high-strength materials and larger hole diameters where stability matters. Their ground geometry and TiN-coated surface make them easier to resharpen and capable of withstanding higher loads, which is why they are often chosen for demanding metalworking tasks. Which 3 drill types exist? The main drill types are metal drills, wood drills and stone/concrete drills. The MetavCUT Twist Drill belongs to the metal drill category and is optimised for metals rather than for wood or masonry. Are you unsure whether this tool meets your specific requirements or need further technical specifications? METAV Werkzeuge provides comprehensive and competent advice for complex tools — contact us anytime at info@metav-werkzeuge.com, call +49 2822 7131930 or message via WhatsApp +49 170 2837271.

Twist Drill — Metal Twist Drill (HSS‑G), Ø 1.5 mm, 135° Tip, DIN 338, Model Spezial, Shaft without multi‑bevel cutting edge and triangular shank, Overall Length 40 mm, Spiral Length 18 mm, Brand MetavCUT A versatile Twist Drill metal drill bit designed for drilling machines and hand drills, engineered for precise holes in a wide range of metals and technical plastics. HSS‑G material for high wear resistance 135° Tip for clean entry in hard materials Conforms to DIN 338 for short cylindrical drills Up to 40% faster drilling performance Reduced feed force by up to 50% Maximise Speed and Reduce Effort with Advanced HSS‑G Technology The HSS‑G composition of this twist drill delivers elevated hardness and thermal stability, which translates into faster drilling and longer tool life when working with alloyed and unalloyed steels. Thanks to the optimized geometry and the 135° Tip, initial penetration is smoother and the risk of walking is reduced, allowing for consistent centring and clean holes. This combination reduces the required feed force, making drilling less physically demanding and improving cycle times on both stationary and portable Drilling Machines. Reliable Hole Quality for Metalworking and Technical Plastics Designed in accordance with DIN 338, this short twist drill provides reproducible results in metals such as Steel, Cast Steel, Gusseisen and Non‑Ferrous Metals, as well as in Hard Plastics. The carefully ground tip produces grit‑free hole edges, minimising post‑processing. For craftsmen and technicians who value neat, repeatable holes, this tool reduces burr formation and supports high‑quality assembly work in workshop and production settings. Practical Use and Compatibility with Common Machines Engineered for use with Hand Drills and standard Drilling Machines, the Twist Drill offers straightforward handling for everyday metalworking tasks. The specified overall and spiral lengths (40 mm and 18 mm respectively) suit through‑holes and shallow blind holes up to typical depths used in mechanical assembly. Because the shaft is supplied without multi‑bevel cutting edge and triangular shank, verify machine chuck compatibility before use; METAV Werkzeuge provides expert advice to ensure the correct bit‑and‑chuck pairing. Who Benefits Most from This Twist Drill This drill bit is aimed at professionals and advanced hobbyists who require dependable performance in metalworking operations. Production technicians, maintenance teams and toolroom staff benefit from predictable cutting behaviour and reduced tool changes due to wear. For those specifying tools for workshop fleets, the conformity to DIN 338 simplifies standardisation and procurement decisions. Durability, Standards and Safe Handling The short design and the HSS‑G material ensure dimensional stability during repeated cycles, while the 135° Tip is especially suitable for tougher materials such as stainless steel. Observing appropriate cutting speeds, coolant use and clamping methods will prolong service life and maintain hole quality. For complex applications or unusual alloys, METAV Werkzeuge offers tailored technical support to define speeds, feeds and coolant strategies. Strongly recommended: Choose the MetavCUT Twist Drill for demanding metalworking tasks and contact METAV Werkzeuge for personalised technical consultation — they provide comprehensive advice to ensure the correct tool selection and optimal machining parameters. For assistance: 📧 info@metav-werkzeuge.com ☎️ +49 2822 7131930 ✔️ WhatsApp +49 170 2837271 Technical Information Designation: Twist Drill Brand: MetavCUT SKU: 55015-FDA Diameter: 1.5 mm Tip Angle: 135° Spiral Length: 18 mm Overall Length: 40 mm Material: HSS‑G Standard: DIN 338 Model Series: Spezial Shaft Execution: without multi‑bevel cutting edge and triangular shank Intended Use: Drills for metal Suitable Machines: Drilling Machine / Hand Drill Manufacturer: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What materials can the MetavCUT Twist Drill (metal Twist Drill) reliably machine? The MetavCUT Twist Drill in HSS‑G is designed for machining alloyed and unalloyed Steel, Cast Steel, Cast Iron, Sintered Iron, Tempered Cast Iron, Non‑Ferrous Metals and Hard Plastics. Its material and geometry ensure wear resistance and consistent cutting performance when used with appropriate speeds and cooling. Why are Twist Drills used and where do they perform best? Twist Drills are primarily used for machining high‑strength materials and larger diameters; they are easy to resharpen and withstand significant loads. The MetavCUT Twist Drill is especially suited to metalworking tasks where clean entry and rapid drilling are required. Which three drill types exist? The main categories are metal drills, wood drills and stone/concrete drills, reflecting the principal material groups and typical cutting geometries. Why are Twist Drills sharpened at the tip? Tip sharpening reduces the cross‑edge at the point of the twist drill, lowering friction and therefore the feed force required. A properly sharpened tip also improves centring in the workpiece, resulting in more accurate and efficient drilling.

Twist Drill — HSS-G Twist Drill (Diameter 1.5 mm | Point Angle 118° | Long | Bright-Finished | Fully Ground | DIN 340) — MetavCUT The Twist Drill is a long HSS-G drill bit for drilling machines, optimised for deep, precise metal drilling and reliable centring in softer metals. Long design for deep or hard-to-reach holes HSS-G Fully Ground for precise metal drilling 1.5 mm diameter for fine, accurate boreholes 118° point angle for easier centring in softer metals Conforms to DIN 340 for standardised performance Faster, cleaner holes thanks to HSS-G and fully ground geometry The HSS-G material and the Fully Ground flute geometry deliver measurable performance advantages for metalworking. Ground flutes created by CNC grinding produce very sharp cutting edges and high concentricity, which results in cleaner bore surfaces and reduced deviation. According to material data, this design can enable up to 40% faster drilling and requires roughly 50% less feed force compared with conventional rolled HSS drills, so users benefit from higher throughput and less operator fatigue in repetitive tasks. Reach deeper and work in confined spaces with the long version The long execution (DIN 340 style) of this Twist Drill provides extended Spiral Length and Overall Length for deeper bores or when the hole lies recessed. With a Spiral Length of 45 mm and Overall Length of 70 mm, this bit is designed to access internal or hard-to-reach positions where a standard-length bit would be too short. This makes it particularly useful for workshop tasks, maintenance jobs and component assembly where extended reach is required while maintaining drill stability. Better centring and controlled entry thanks to the 118° point A Point Angle of 118° is well suited to softer metals and many non-ferrous materials, offering a compromise between cutting aggression and centring behaviour. The geometry reduces the tendency to wander on curved or uneven surfaces and improves initial positioning without excessive burr formation. For customers unfamiliar with drilling geometry: a larger Point Angle spreads the cutting action, while a smaller angle aids centring on rounded parts — 118° is often chosen for general metalwork and for easier start in aluminium and similar materials. Built for metalworking professionals and versatile applications This Twist Drill from MetavCUT is engineered for drilling machines and is primarily intended for metalworking tasks. It is suitable for alloyed and unalloyed steels, cast and temper steels, grey and spheroidal cast irons, sintered iron, non-ferrous metals and hard plastics. The Bright-Finished surface aids corrosion resistance and handling, while the Fully Ground shank supports precise clamping and minimal runout. Note that ground HSS can be more brittle than rolled types, so the bit performs best under controlled feed and with appropriate cooling on stationary or machine setups. Strong recommendation: For precision deep-metal drilling choose the MetavCUT Twist Drill with HSS-G and DIN 340 long execution — METAV Werkzeuge provides expert advice and support, contact us at 📧 info@metav-werkzeuge.com ☎️ +49 2822 7131930 ✔️ WhatsApp +49 170 2837271 Technical Information Designation: Twist Drill Marke: MetavCUT SKU: 53015-FDA Diameter: 1.5 mm Point Angle: 118° Execution: Long (DIN 340 style) Colour / Finish: Bright-finished For Drilling Machine: Drilling Machine Spiral Length: 45 mm Overall Length: 70 mm Shank Execution: Fully Ground Model Series: Standard Line Material: HSS-G Norm: DIN 340 Application: Drills for metal Hersteller: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ Can the MetavCUT Twist Drill be used in a hand drilling machine? The MetavCUT Twist Drill is suitable for use in a drilling machine; however, because the HSS-G Fully Ground geometry can be more brittle than rolled types, it performs best in a stable drilling setup or with controlled feed and appropriate cooling when used in portable applications. Is cooling necessary for the MetavCUT Twist Drill when drilling steel? When using the MetavCUT Twist Drill in steel or other hard materials, applying coolant or cutting fluid is recommended to extend tool life and maintain cutting performance for this HSS-G Twist Drill. What is a Twist Drill used for? A Twist Drill is primarily applied to the machining of high-strength materials and larger drill diameters. The form is easy to regrind and can withstand greater loads. The MetavCUT Twist Drill is therefore used especially for deep holes and demanding metalworking tasks. Which three drill types are there? The three main drill types are metal drills, wood drills and stone/concrete drills. For metalworking tasks the MetavCUT Twist Drill belongs to the metal drill category. Why are Twist Drills pointed? The point sharpening reduces the cross-cut at the tip of the Twist Drill. By pointing the tip, friction forces are significantly reduced so lower feed forces are required and the drill tip centres more accurately in the workpiece. Can you use a metal Twist Drill for wood? A metal Twist Drill such as the MetavCUT Twist Drill can be used in wood, but it offers poorer guidance and a less clean finish compared with dedicated wood drills. Metal drills are easier to regrind and have lower self-feeding tendency.

Twist Drill — Type N short HSS drill, 1.6 mm, 118°, black, DIN 338 The Twist Drill Type N is a short High Speed Steel drill designed for precise metal drilling with a 1.6 mm diameter and a 118° point angle, suitable for Drilling Machines and hand drills. Short HSS Twist Drill 1.6 mm diameter 118° point angle for quick centring DIN 338 short design for higher stability Type N normal spiral for metal machining Black finish for corrosion resistance Greater accuracy thanks to short design and high rigidity A short configuration reduces overhang and bending, delivering improved stability and more accurate hole positions when working with metal. The compact geometry of this Twist Drill minimises chatter and allows consistent feeds even when using portable Drilling Machines. Professionals and hobbyists benefit from a compact bit that keeps drill axis deviation low, producing clean holes with minimal rework. Robust HSS material and application guidance for metal Manufactured from HSS (High Speed Steel), this Type N drill combines wear resistance with toughness; the material choice makes the bit suitable for alloyed and unalloyed steel, cast iron, non‑ferrous metals and certain plastics. The 118° point angle offers reliable centring on common metal surfaces and is a practical compromise between cutting aggressiveness and tip life. For best results use steady feed rates and correct cutting fluid when machining harder materials. Who should use this drill and how it stands out This Twist Drill targets workshops, tool rooms and dedicated DIY users who require precision in metalworking. The Type N normal spiral is optimised for metal cutting, providing efficient chip evacuation and predictable performance. The black surface finish improves resistance to corrosion during storage and handling. Choose this short HSS bit when dimensional accuracy and durability matter more than deep-hole capability. We recommend the MetavCUT Twist Drill for reliable metal machining — for technical advice or to confirm suitability contact METAV Werkzeuge: info@metav-werkzeuge.com | Tel: +49 2822 7131930 | WhatsApp: +49 170 2837271 Bezeichnung: Twist Drill Marke: MetavCUT SKU: 40016-FDA Durchmesser: 1.6 mm Spitzenwinkel: 118° Gesamtlänge: 43 mm Spirallänge: 20 mm Ausführung: short Typ: Type N Material: HSS Farbe: black Für Bohrmaschine: Drilling Machine Norm: DIN 338 Anwendung: Drills for metal Hersteller: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What is the MetavCUT Twist Drill mainly used for? The MetavCUT Twist Drill (Type N) is primarily used for machining high‑strength materials and larger-diameter metal holes; its shape is easy to regrind and it withstands higher loads, making it suitable for demanding metalworking tasks. Which three drill types exist? In general the three main drill categories are Metal drills, Wood drills and Stone/Concrete drills; the MetavCUT Twist Drill belongs to the metal drill group and is optimised for cutting metal. Is the MetavCUT Twist Drill suitable for stainless steel? The MetavCUT Twist Drill in HSS can drill stainless steel with correct coolant and reduced feed; however for prolonged work in highly abrasive or very hard stainless grades consider specialised coatings or higher‑alloy variants. How should the MetavCUT Twist Drill be sharpened and maintained? Sharpen the Twist Drill on a bench grinder or dedicated drill sharpener following the original point geometry; maintaining the 118° point and even lips preserves centring and reduces required feed forces.

Twist Drill — Type N short, Ø 1.6 mm, 118°, 5% cobalt-alloyed, HSS‑E, DIN 338, Fully Ground (MetavCUT) The Twist Drill Type N short is a precision metal‑drilling tool designed for use in a Drilling Machine, offering a compact overall length and high stability for accurate holes in steel and non‑ferrous metals. Precision short design for stable drilling 1.6 mm Diameter for fine metalwork 118° Tip angle for reliable penetration in softer metals 5% Cobalt‑alloyed HSS‑E for heat resistance and wear life Fully ground shank for high runout accuracy Greater Stability for Accurate Metal Holes The short configuration of this Twist Drill reduces the cantilevered length at the chuck, which results in noticeably lower deflection and improved positional accuracy when drilling. The shorter Spiral Length combined with a compact Overall Length provides a clear benefit for demanding jobs where hole tolerance matters. For workshops using a Drilling Machine, this translates into fewer rejects and less rework, because the tool geometry favours straight, concentric holes even in tougher metals. Heat Resistance and Consistent Cutting Performance Made from HSS‑E with a 5% cobalt alloy, the drill resists softening at elevated temperatures, which preserves cutting edge geometry during prolonged use. The 118° Tip Angle supports efficient cutting in softer steels and reduces walking on curved surfaces, while the Type N Normal Spiral geometry remains the recommended choice for general metal drilling. This material and geometry pairing means longer tool life under intermittent loads and improved chip evacuation in typical metalworking applications. High Precision Finish through Fully Ground Geometry The fully ground flute and geometry, compliant with DIN 338, ensure sharp cutting lips and excellent concentricity. Grinding produces cleaner cutting edges than roll‑forming, which leads to superior hole quality and a better surface finish in the workpiece. Because ground drills can be more brittle than rolled equivalents, it is advisable to use appropriate coolant and moderate feed rates for deep or interrupted cuts to avoid premature tool breakage. Suited Users and Typical Applications This short Type N twist drill is aimed at metalworkers, toolrooms and engineering workshops that require reliable small‑diameter drilling in alloyed and unalloyed steels, cast iron, non‑ferrous metals and plastics. The design is particularly helpful when working on a Drilling Machine where rigidity and repeatable positioning are priorities. For users uncertain about compatibility with specific materials or machine setups, METAV Werkzeuge provides expert consultation to match tooling to application and to recommend optimal machining parameters. Strong recommendation: The MetavCUT Twist Drill short Type N is ideal for precision metalworking—contact METAV Werkzeuge for personalised technical advice via eMail info@metav-werkzeuge.com, phone +49 2822 7131930 or WhatsApp +49 170 2837271 Twist Drill Brand: MetavCUT SKU: 47016-FDA Diameter: 1.6 mm Tip angle: 118° Type: Type N Execution: short Overall length: 43 mm Spiral length: 20 mm Material: HSS‑E (5% cobalt‑alloyed) Shank execution: fully ground Application: Drills for metal / suitable for Drilling Machine Model series: Standard Line Norm: DIN 338 Manufacturer: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ For what is a Twist Drill used? The MetavCUT Twist Drill Type N is primarily applied to the machining of high‑strength materials and larger drill diameters; its short design and material composition make it suitable for demanding metal drilling tasks where stability and precision are required. The geometry is easy to re‑grind and withstands higher loads. Which three drill types exist? Commonly distinguished drill types are Metal Drills (like the MetavCUT Type N Twist Drill), Wood Drills, and Stone/Concrete Drills, each optimised in geometry and material for its respective substrate. Why are Twist Drills sharpened at the tip? The tip sharpening reduces the size of the cross‑cutting edge, which significantly lowers friction and therefore reduces the required feed force. Sharpening also improves centring of the drill tip in the workpiece. Can a metal Twist Drill be used to drill wood? A metal Twist Drill such as the MetavCUT Type N can be used in wood, but guidance and finish are inferior compared with dedicated wood drills. Metal drills are easier to re‑grind and typically exhibit less self‑feeding action in wood.

Spiralbohrer – kurzer HSS-G Spiralbohrer Ø 1,6 mm · 118° · Typ N · blank · geschliffen · DIN 338 · Profi Line von MetavCUT Der Spiralbohrer ist ein kurzer HSS-G Bohrer für präzise Metallbohrungen, ideal für feinmechanische Anwendungen und die Bearbeitung harter Werkstoffe. Kurze Ausführung für höhere Stabilität Geschliffene HSS-G Geometrie für saubere Bohrbilder Spitzenwinkel 118° für gutes Zentrierverhalten Normgerechte Ausführung nach DIN 338 Geeignet für präzise Maschinenfertigung Höhere Stabilität für präzise Metallbohrungen Die kurze Ausführung sorgt für eine deutlich reduzierte Auskraglänge und damit für höhere Stabilität beim Bohren in Metall. Gerade bei einem Durchmesser von 1,6 mm ist die verminderte Neigung zum Verbiegen entscheidend, um Ausbrüche und Maßabweichungen zu vermeiden. Durch die Kombination aus kurzer Gesamtlänge und geschliffenem Schaft wird eine präzise, vibrationsärmere Führung erreicht, die besonders bei empfindlichen Bauteilen zu einem saubereren Bohrbild führt und Nacharbeit reduziert. Geschliffene HSS-G Qualität: schneller und sauberer Schnitt Der HSS-G Werkstoff mit geschliffener Spirale liefert sehr scharfe Schneiden und hohe Rundlaufgenauigkeit. Dadurch ist ein bis zu 40 % schnelleres Bohren möglich, während zugleich die erforderliche Anpresskraft um etwa 50 % reduziert wird. Der Begriff geschliffen bedeutet, dass die Spannuten per CNC-Schliff ausgeformt sind, was saubere Späne und exakte Bohrungsdurchmesser fördert. Wegen der höheren Sprödigkeit empfiehlt sich der Betrieb unter Kühlung und an stationären Maschinen mit guter Rundlaufpräzision. Praktische Hinweise für sicheren Einsatz und beste Ergebnisse Für den Einsatz des kurzen HSS-G Spiralbohrers empfiehlt sich eine hohe Drehzahl bei moderatem Vorschub; zu starker Druck erhöht die Bruchgefahr bei kleinen Durchmessern. Tiefe Sacklochbohrungen sollten vermieden werden, da die Späne bei sehr kleinen Bohrern schnell Probleme bereiten. Bei Bedarf ist ein Anpicken oder Vorbohren auf einer stabilen Maschine sinnvoll. Durch den Typ N Normalspirale ist der Bohrer speziell für die Bearbeitung von legierten und unlegierten Stählen, Gusseisen und Nichteisenmetallen ausgelegt. Wer profitiert von dieser Profi-Line-Lösung? Die Profi Line von MetavCUT richtet sich an Anwender in Feinmechanik, Modellbau, Uhrenindustrie, Elektronikfertigung und an Werkstätten, die präzise Metallbohrungen erfordern. Der Spiralbohrer ist ideal, wenn es auf enge Toleranzen und saubere Bohrbilder ankommt. Anwender, die auf stationäre oder hochgenaue Werkzeugmaschinen setzen, nutzen die Vorteile der DIN-338-Norm und der geschliffenen Ausführung voll aus. Vertrauen Sie auf die MetavCUT Profi Line HSS-G Qualität für präzise Metallbohrungen und lassen Sie sich bei Fragen zur Anwendung und Auswahl gern persönlich beraten: info@metav-werkzeuge.com oder Tel. +49 2822 7131930 Bezeichnung: Spiralbohrer Marke: MetavCUT SKU: 48016-FDA Durchmesser: 1,6 mm Gesamtlänge: 49 mm Spirallänge: 24 mm Spitzenwinkel: 118° Typ: Typ N (Normalspirale) Material: HSS-G (geschliffen) Schaft-Ausführung: geschliffen, Zylinderschaft Ausführung: kurz Farbe: blank Norm: DIN 338 Anwendung: Bohren in legierten und unlegierten Stahl, Gussstahl, Gusseisen, Sintereisen, Temperguss, Nichteisenmetalle und Hartkunststoff Empfohlene Maschinen: stationäre, hochpräzise Bohrmaschinen; bei Einsatz beachten: Kühlung und runden Lauf prüfen Hersteller: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ Ist der Spiralbohrer von MetavCUT Profi Line für Handbohrmaschinen geeignet? Der MetavCUT Spiralbohrer in kurzer HSS-G Ausführung ist für sehr feine Durchmesser wie 1,6 mm grundsätzlich für präzise, stationäre Maschinen konzipiert; bei Handgeführten Maschinen steigt die Bruch- und Verkantungsgefahr, daher wird der Einsatz an stabilen Antrieben empfohlen. Welche Werkstoffe lassen sich mit dem MetavCUT Spiralbohrer bearbeiten? Mit dem MetavCUT HSS-G Spiralbohrer lassen sich legierte und unlegierte Stähle, Gusswerkstoffe sowie Nichteisenmetalle und harte Kunststoffe zuverlässig bearbeiten, wobei die geschliffene Geometrie saubere Bohrbilder gewährleistet. Warum ist der Spitzenwinkel 118° wichtig bei diesem Spiralbohrer? Der Spitzenwinkel von 118° beim MetavCUT Spiralbohrer unterstützt ein gutes Zentrierverhalten und erleichtert das Eindringen in viele Metallwerkstoffe, speziell bei feineren Durchmessern; für spezielle Materialien kann ein anderer Winkel vorteilhaft sein. Wie kann ich die Standzeit des MetavCUT Spiralbohrers verlängern? Die Standzeit des MetavCUT HSS-G Spiralbohrers lässt sich durch passende Drehzahlwahl, ausreichende Kühlung und moderaten Vorschub erhöhen; außerdem vermeiden kurze Bohrzyklen und das Vorbohren tiefer Löcher unnötige Belastungen. {"@context":"https://schema.org","@graph":[{"@type":"Product","@id":"#48016-FDA","sku":"48016-FDA","mpn":"48016-FDA","name":"Spiralbohrer 48016-FDA","description":"Kurzer HSS-G Spiralbohrer Ø 1,6 mm, 118° Spitzenwinkel, Typ N Normalspirale, blank, geschliffen, DIN 338; geeignet für präzise Metallbohrungen in legierten und unlegierten Stählen, Gusswerkstoffen und Nichteisenmetallen; Profi Line von MetavCUT.","image":["https://files.plytix.com/api/v1.1/file/public_files/pim/assets/57/c3/98/62/6298c3575d155f1bc7e497fd/images/8e/48/c5/69/69c5488eb2b3400ba580741b/logo-metav-1200-1200.png","https://files.plytix.com/api/v1.1/file/public_files/pim/assets/57/c3/98/62/6298c3575d155f1bc7e497fd/images/8e/48/c5/69/69c5488eb2b3400ba580741e/logo-metav-1200-900.png","https://files.plytix.com/api/v1.1/file/public_files/pim/assets/57/c3/98/62/6298c3575d155f1bc7e497fd/images/8e/48/c5/69/69c5488eb2b3400ba580741c/logo-metav-1200-675.png"],"additionalProperty":[{"@type":"PropertyValue","name":"Bezeichnung","value":"Spiralbohrer"},{"@type":"PropertyValue","name":"Marke","value":"MetavCUT"},{"@type":"PropertyValue","name":"Durchmesser","value":"1,6 mm"},{"@type":"PropertyValue","name":"Gesamtlänge","value":"49 mm"},{"@type":"PropertyValue","name":"Spirallänge","value":"24 mm"},{"@type":"PropertyValue","name":"Spitzenwinkel","value":"118°"},{"@type":"PropertyValue","name":"Typ","value":"Typ N (Normalspirale)"},{"@type":"PropertyValue","name":"Material","value":"HSS-G (geschliffen)"},{"@type":"PropertyValue","name":"Schaft-Ausführung","value":"geschliffen, Zylinderschaft"},{"@type":"PropertyValue","name":"Ausführung","value":"kurz"},{"@type":"PropertyValue","name":"Farbe","value":"blank"},{"@type":"PropertyValue","name":"Norm","value":"DIN 338"},{"@type":"PropertyValue","name":"Anwendung","value":"Bohren in legierten und unlegierten Stahl, Gussstahl, Gusseisen, Sintereisen, Temperguss, Nichteisenmetalle und Hartkunststoff"},{"@type":"PropertyValue","name":"Empfohlene Maschinen","value":"stationäre, hochpräzise Bohrmaschinen; Kühlung und Rundlauf prüfen"},{"@type":"PropertyValue","name":"Spezialmerkmal","value":"geschliffene HSS-G Geometrie für saubere Bohrbilder und hohe Rundlaufgenauigkeit"},{"@type":"PropertyValue","name":"Hersteller","value":"MetavCUT"},{"@type":"PropertyValue","name":"Modellserie","value":"Profi Line"}],"offers":{"@type":"Offer","price":"0.47","priceCurrency":"EUR"}},{"@type":"FAQPage","mainEntity":[{"@type":"Question","name":"Ist der Spiralbohrer von MetavCUT Profi Line für Handbohrmaschinen geeignet?","acceptedAnswer":{"@type":"Answer","text":"Der MetavCUT Spiralbohrer 48016-FDA ist als kurzer HSS-G Bohrer für präzise, stationäre Maschinen konzipiert; bei handgeführten Maschinen steigt die Bruch- und Verkantungsgefahr, daher wird der Einsatz an stabilen Antrieben empfohlen."}},{"@type":"Question","name":"Welche Werkstoffe lassen sich mit dem MetavCUT Spiralbohrer bearbeiten?","acceptedAnswer":{"@type":"Answer","text":"Mit dem MetavCUT Spiralbohrer 48016-FDA lassen sich legierte und unlegierte Stähle, Gusswerkstoffe sowie Nichteisenmetalle und harte Kunststoffe zuverlässig bearbeiten; die geschliffene Geometrie sorgt für saubere Bohrbilder."}},{"@type":"Question","name":"Warum ist der Spitzenwinkel 118° wichtig bei diesem Spiralbohrer?","acceptedAnswer":{"@type":"Answer","text":"Der Spitzenwinkel 118° beim MetavCUT Spiralbohrer 48016-FDA verbessert das Zentrierverhalten und erleichtert das Eindringen in viele Metallwerkstoffe, insbesondere bei feineren Durchmessern."}},{"@type":"Question","name":"Wie kann die Standzeit des MetavCUT Spiralbohrers verlängert werden?","acceptedAnswer":{"@type":"Answer","text":"Die Standzeit des MetavCUT Spiralbohrers 48016-FDA lässt sich durch passende Drehzahlwahl, ausreichende Kühlung und moderaten Vorschub erhöhen; Vorbohren und kurze Bohrzyklen vermindern die Bruchgefahr."}}]},{"@type":"ItemPage","url":"https://metav-shop.de/spiralbohrer-48016-fda","dateModified":"2026-05-04T12:00:00+01:00","author":{"@type":"Person","name":"Stephan Bayer","url":"https://www.linkedin.com/in/stephan-bayer/"},"publisher":{"@type":"Organization","name":"Metav Werkzeuge GmbH","url":"https://metav-shop.de","logo":{"@type":"ImageObject","url":"https://files.plytix.com/api/v1.1/file/public_files/pim/assets/57/c3/98/62/6298c3575d155f1bc7e497fd/images/8e/48/c5/69/69c5488eb2b3400ba580741c/logo-metav-1200-675.png","width":1200,"height":675},"address":{"@type":"PostalAddress","streetAddress":"Parkring 45","postalCode":"46446","addressLocality":"Emmerich","addressCountry":"DE"},"telephone":"+49 2822 7131930","email":"info@metav-werkzeuge.com"},"about":[{"@type":"Thing","name":"Spiralbohrer HSS-G kurz"},{"@type":"Thing","name":"Profi Line für präzise Metallbohrungen"},{"@type":"Thing","name":"Norm DIN 338"}],"mentions":[{"@type":"Thing","name":"Zylinderschaft geschliffen"},{"@type":"Thing","name":"Typ N Normalspirale"},{"@type":"Thing","name":"Geschliffene Geometrie HSS-G"}]}]}

Twist Drill — Type N short HSS, 1.75 mm diameter, 118° point angle, black, DIN 338 A Twist Drill (Type N) designed for precise metal drilling with a 1.75 mm diameter and a 118° point angle for reliable centring in standard machining applications. Short HSS Type N for precise metal drilling 118° point angle for reliable centring 1.75 mm diameter with 43 mm overall length DIN 338 compliance for standardised quality Black short design for enhanced stability High stability and material benefits for demanding metalwork Constructed from HSS (High Speed Steel), this short Twist Drill offers a robust balance of elasticity and strength that reduces the breakage risk when machining small diameters. The short execution increases stability and minimises deflection during drilling, which results in more consistent hole geometry and longer life under cyclic loads. For customers requiring dependability in series production, the combination of HSS and a short design delivers a reliable solution. Suitable applications and what the geometry achieves The Type N geometry is the classical choice for metalworking: ideal for drilling in alloyed and unalloyed steel, cast iron, non-ferrous metals and plastics. The 118° point angle provides easier penetration and better centring on mildly curved surfaces, which helps reduce wandering at the start of a hole. When paired with appropriate speeds and feeds, this drill suits both stationary drilling machines and hand-operated drilling machines for controlled, repeatable results. Who benefits from this tool and why it was made Engineers, toolroom technicians and maintenance professionals who require precise, stable holes in metal will value the short design and DIN 338 standard compliance. The drill is optimised for situations where rigidity matters more than reach, such as countersunk setups, jig operations or when machining on workpieces with limited overhang. The short flute length simplifies chip evacuation for small diameters, supporting efficiency on the shop floor. Standard conformity and practical guidance for selection Compliant with DIN 338, this short twist drill meets the dimensional and production specifications expected in industrial environments. The designation “short” refers to the reduced overall and spiral length, improving rigidity compared with standard-length drills of the same diameter. For small-diameter holes up to the specified length, this design minimises vibration and produces a cleaner finish, making it suitable for precision tasks in metal fabrication. Strong recommendation: The MetavCUT Twist Drill Type N in HSS is an excellent choice for stable, precise metal drilling — for further technical advice or to confirm suitability for specific applications, contact METAV Werkzeuge: info@metav-werkzeuge.com • +49 2822 7131930 • WhatsApp +49 170 2837271 Designation: Twist Drill Brand: MetavCUT SKU: 400175-FDA Diameter: 1.75 mm Point angle: 118° Type: Type N Colour: black Execution: short Material: HSS Spiral length: 20 mm Overall length: 43 mm Norm: DIN 338 Application: Drills for metal For drilling machine: Drilling Machine Manufacturer: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ For what is a Twist Drill used? The MetavCUT Twist Drill Type N is primarily used for machining high-strength materials and larger drilling diameters in metalworking; its design is easy to regrind and withstands higher loads. Which three drill types exist? Commonly distinguished drill types are metal drills, wood drills and stone/concrete drills; the MetavCUT Twist Drill Type N belongs to the metal drill category. Why are twist drills pointed? The point sharpening reduces the cross-edge at the drill tip; for the MetavCUT Twist Drill Type N this lowers friction, reduces required feed forces and improves centring in the workpiece. Can a Twist Drill be used to drill wood? A metal drill such as the MetavCUT Twist Drill Type N can be used in wood, but it offers less guidance and a less clean finish compared with dedicated wood drills; it is, however, easier to regrind and has a lower self-feeding tendency. For which drilling depths is the Twist Drill most used? A full-diameter through-hole is often performed with a twist drill; for diameters up to around 20 mm and drilling depths up to about 100 mm, the twist drill is the most frequently used tool, applicable to the MetavCUT Twist Drill Type N within its length limits. What is better, HSS or HSSE? The common belief that HSSE steels are universally superior to HSS is not correct; choice should be based on actual working conditions and whether those conditions justify the higher price — the MetavCUT Twist Drill Type N in HSS is suited to many standard metalworking tasks.

Twist Drill — Type N Short HSS, 1.7 mm, 118°, Black, DIN 338 The Twist Drill (Type N) is a short HSS metal drill designed for precision drilling with a 1.7 mm diameter and a 118° tip angle, suitable for use in drilling machines and hand drills. Short design for high stability Precision 1.7 mm diameter for fine holes 118° tip angle for fast centring HSS construction for metalworking durability Conforms to DIN 338 for standardised quality High stability and accuracy for metalworking tasks Thanks to its short design and HSS material, this short twist drill provides increased rigidity and reduced bending during operation, which translates directly into more accurate hole positions. The reduced overhang improves tool life in demanding metalworking environments, making it ideal for setups where concentricity matters. Use in hand drills and drilling machines benefits from the stable geometry to achieve repeatable results with minimal runout. Optimised tip geometry for reliable penetration The 118° tip angle is chosen to balance entry behaviour and centring for common metals; it facilitates reliable penetration and reduces walking on curved or non-flat surfaces. For operators unfamiliar with tip angles: a smaller angle eases initial centring, while larger angles shorten the time to break through harder materials. This Type N geometry is a classic choice for metal, offering dependable starting behaviour without excessive cratering. Material selection and standard conformity for consistent performance Manufactured from HSS (High Speed Steel) and complying with DIN 338, this short twist drill offers a combination of toughness and heat resistance appropriate for alloyed and unalloyed steels, cast iron, non-ferrous metals and plastics. DIN 338 classification ensures consistent dimensions and shank form, simplifying tool selection for machining centres and maintenance workshops that require standardised replacement tools. Practical application and who benefits most Designed primarily for precision metal drilling, the tool suits workshop technicians, toolmakers and maintenance personnel who require fine-diameter holes with reliable centring. The short length reduces flex and is particularly advantageous when drilling up to moderate depths in tough materials, where stability and repeatability are key requirements for production or repair tasks. We recommend the MetavCUT Twist Drill (Type N) for any workshop needing a robust, short HSS solution for precise metal drilling — for personalised advice or additional technical details contact METAV Werkzeuge: info@metav-werkzeuge.com | Tel +49 2822 7131930 | WhatsApp +49 170 2837271 Technical Specifications Bezeichnung: Twist Drill Marke: MetavCUT SKU: 40017-FDA Typ: Type N Durchmesser: 1.7 mm Spitzenwinkel: 118° Gesamtlänge: 43 mm Spirallänge: 20 mm Ausführung: short Material: HSS Norm: DIN 338 Farbe: black Für Bohrmaschine: Drilling Machine Anwendung: Drills for metal Hersteller: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What is the Twist Drill by MetavCUT Type N used for? The Twist Drill from MetavCUT (Type N) is primarily used for drilling high-strength materials and larger diameters in metalworking; its shape makes it easy to resharpen and able to withstand higher loads, which is why it is commonly chosen for demanding applications. Which three drill types exist? The three main drill types are Metal drills, Wood drills and Stone/Concrete drills, and the MetavCUT Twist Drill (Type N) belongs to the category of metal drills optimised for steel and similar materials.

Twist Drill (Type N) — short, Ø 1.7 mm, 118°, 5% Cobalt-Alloyed, HSS‑E, DIN 338 — fully ground shank — MetavCUT The Twist Drill (Type N) is a short HSS‑E metalworking drill designed for Drilling Machines, offering enhanced stability and precision for demanding metal‑drilling tasks. Short design for improved stability 5% Cobalt‑alloyed HSS‑E for increased heat resistance DIN 338 compliant for short twist drills Fully ground shank for high concentricity 118° point angle for easier centring in softer metals Short length for maximum stability and precise holes Thanks to its short design, this Twist Drill minimises overhang from the chuck, which significantly reduces bending and vibration during cutting. As a result, the tool achieves better concentricity and an improved surface finish in drilled holes. This makes the drill especially suitable for workshop situations where repeatable, accurate hole geometry is essential, for example in jigs, fixtures and precision metal components. Alloyed HSS‑E chemistry delivers longer tool life under heat Manufactured from HSS‑E with 5% cobalt alloy, the drill combines toughness with superior red‑hardness compared to standard HSS. This material composition increases resistance to softening at elevated cutting temperatures, allowing for higher cutting speeds and extended tool life when machining steels and other metals. The cobalt content also supports easier regrinding, so maintenance and tool refurbishment remain cost‑effective. Geometry and finish optimised for metalworking performance The 118° point angle provides a compromise between entry sharpness and robustness and aids centring on slightly irregular surfaces; it is particularly helpful when working with softer non‑ferrous metals. The fully ground flute and shank geometry ensure sharp cutting edges and high run‑out accuracy, producing clean holes and reducing burr formation. Conforming to DIN 338, this short twist drill is engineered for consistent quality across batches. Intended applications and target users Engineered for Drilling Machines and manual drill presses, this Twist Drill is tailored to professional workshops, toolrooms and maintenance departments that require reliable metal drilling. Typical applications include machining of alloyed and unalloyed steel, cast iron, non‑ferrous metals and technical plastics. The combination of HSS‑E material and short design supports both stationary machine use and demanding hand‑held operations where rigidity and precision are required. Strong recommendation: For precision metalworking choose the MetavCUT Twist Drill Type N with HSS‑E 5% cobalt alloy — for technical questions or tailored advice METAV Werkzeuge provides expert support via eMail: info@metav-werkzeuge.com, Phone: +49 2822 7131930, WhatsApp: +49 170 2837271 Designation: Twist Drill Brand: MetavCUT SKU: 47017-FDA Diameter: 1.7 mm Overall Length: 43 mm Spiral Length: 20 mm Point Angle: 118° Type: Type N Execution: short Material: HSS‑E Alloy/Coating: 5% cobalt‑alloyed Shank Execution: fully ground For: Drilling Machine Application: Drills for metal Model Series: Standard Line Norm: DIN 338 Manufacturer: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What materials is the MetavCUT Twist Drill Type N suitable for? The MetavCUT Twist Drill Type N is suitable for alloyed and unalloyed steels, cast iron, non‑ferrous metals and various plastics; its HSS‑E chemistry with 5% cobalt improves performance on harder or heat‑sensitive cuts and supports higher cutting speeds while maintaining tool life. What is a Twist Drill mainly used for? A Twist Drill such as the MetavCUT Type N is mainly applied when machining high‑strength materials and larger drill diameters; its design is comparatively easy to regrind and can withstand greater mechanical loads, making it a reliable choice for demanding metalworking operations. Which three drill types are there? Common drill types are: Metal drills, Wood drills and Stone/Concrete drills; the MetavCUT Twist Drill Type N belongs to the metal drill category and is optimised for machining metallic materials.

Twist Drill — Type N, 1.8 mm, 118°, Short HSS, Black, DIN 338 (MetavCUT) The Twist Drill Type N is a short HSS metal-drilling bit designed for precise, stable holes in steel and non‑ferrous metals using drilling machines and hand drills. Short design for high stability and precision HSS material for wear-resistant metal drilling 118° tip for improved centring on curved surfaces DIN 338 compliant for standardised quality Suitable for Drilling Machines and Hand Drills Faster, more reliable results thanks to short HSS construction The Twist Drill features a Short overall profile with a Spiral Length of 22 mm and an Overall Length of 46 mm, which reduces overhang and dramatically improves stability during drilling. Made from HSS (High Speed Steel), the bit combines elasticity with wear resistance; this manufacturing method lowers breakage risk for holes below 6 mm and keeps the cutting edge durable under standard metalworking loads. As a result, operators achieve cleaner holes with less vibration and better tool life. Precise centring and controlled penetration for metalworking A 118° Tip Angle gives this Type N geometry reliable centring on slightly curved or irregular surfaces and reduces the tendency to wander at startup. While larger tip angles are used for very hard materials, the 118° geometry is effective for many steels, cast iron and non‑ferrous metals, balancing entry sharpness and cutting life. The normal spiral flute design evacuates chips efficiently, supporting steady feed rates and consistent hole quality. Optimised for workshop use and maintenance tasks Engineers, maintenance technicians and hobbyists benefit from the Type N design: a classic metal‑drilling profile that excels in routine shop and site tasks. Compatibility with standard Drilling Machines and common chucks ensures easy integration into existing toolsets. The compact length makes the bit particularly useful when access is limited or when rigidity is paramount, for instance when drilling in fixtures, jigs or on portable workpieces. Conformity, resharpening and practical handling Conforming to DIN 338, this short Twist Drill follows standardised dimensions and tolerances, making replacement and inventory straightforward. The short geometry also simplifies resharpening: the flute and point shape are easy to regrind while maintaining the original cutting geometry. For best results, clamp the bit securely, use appropriate cutting fluid for ferrous metals and avoid excessive feed to prevent overheating. Proper storage and occasional light resharpening extend service life and maintain hole accuracy. Highly recommended: Choose MetavCUT’s Twist Drill Type N for precise, stable metal drilling — for personalised technical advice METAV Werkzeuge is pleased to assist you at info@metav-werkzeuge.com, Tel +49 2822 7131930 or WhatsApp +49 170 2837271 Designation: Twist Drill Brand: MetavCUT SKU: 40018-FDA Type: Type N Diameter: 1.8 mm Tip angle: 118° Material: HSS Overall length: 46 mm Spiral length: 22 mm Execution: Short Standard: DIN 338 Colour: Black Application: Drills for metal Suitable for: Drilling Machine Manufacturer: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What is the Twist Drill used for? The Twist Drill from MetavCUT, Type N, is primarily used for machining high‑strength materials and larger drill diameters in metalworking. Its shape allows for straightforward resharpening and it endures higher loads, making it suitable for through‑holes and robust workshop applications. Which three drill types are there? Common drill categories are Metal Drill, Wood Drill and Stone/Concrete Drill; the Twist Drill (MetavCUT, Type N) belongs to the Metal Drill group and is optimised for steel and similar materials.

Twist Drill — Short Type N Twist Drill, 1.8 mm, 118° Tip, 5% Cobalt‑Alloyed, HSS‑E, DIN 338, Fully Ground Shank by MetavCUT The Twist Drill short Type N is a precision metalworking drill bit designed for use in hand Drilling Machines and stationary equipment for reliable, clean holes in a wide range of metals. Short design reduces deflection and improves precision 5% Cobalt‑alloyed HSS‑E for higher heat resistance 118° Tip for clean entry in softer metals Fully ground shank for high runout accuracy Conforms to DIN 338 for standardized dimensions Greater stability and wear resistance for demanding metalwork The short design of this Twist Drill minimises overhang and therefore reduces the risk of bending during operation, resulting in higher precision in every hole. Manufactured from HSS‑E with 5% cobalt, the bit offers improved heat resistance and longer life when drilling alloys and harder steels. As a Type N Normal Spiral it is particularly well suited to metal applications and follows the dimensional and production guidelines of DIN 338 for consistent performance. Built for accurate alignment and clean hole starts A fully ground shank ensures excellent concentricity and low runout in both hand and bench Drilling Machines, improving hole quality and tool life. The 118° tip angle facilitates a clean entry, especially in softer materials such as aluminium, while the short overall geometry (Total Length 46 mm, Spiral Length 22 mm) increases stiffness. This combination yields precise centring and a controlled cutting action that benefits workshop professionals and maintenance technicians alike. Practical advantages, recommended uses and handling This Twist Drill is ideal for professional metalworkers, maintenance crews and precision hobbyists who need reliable results in alloys, Cast Iron, non‑ferrous metals and plastics. The roll‑or‑grind manufacturing choices mean the ground version delivers sharper cutting edges and better roundness, though it benefits from appropriate cooling to reduce the risk of breakage. For drilling below 6 mm diameter, the low‑temperature treatment used in production increases elasticity and reduces fracture risk, making the bit a smart choice for repeated, precise metal drilling tasks. MetavCUT’s short Twist Drill is recommended for precision metal drilling — for expert technical advice and application support contact METAV Werkzeuge: info@metav-werkzeuge.com | Tel: +49 2822 7131930 | WhatsApp: +49 170 2837271 Designation: Twist Drill (Short Type N) Brand: MetavCUT SKU: 47018-FDA Diameter: 1.8 mm Tip Angle: 118° Material: HSS‑E (High Speed Steel, Cobalt alloyed) Alloy/Coating: 5% cobalt‑alloyed Type: Type N (Normal Spiral) Execution: Short Overall Length: 46 mm Spiral Length: 22 mm Shank Finish: Fully ground Application: Drills for metal / suitable for Hand Drilling Machine and stationary machines Standard/Norm: DIN 338 Model Series: Standard Line Manufacturer: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What is the Twist Drill used for? The MetavCUT Twist Drill (Type N) is mainly applied to machining high‑strength materials and larger drill diameters; its design is easy to regrind and endures higher loads, which makes it suitable for demanding metalworking tasks. Which three drill types exist? The common drill categories are Metal drill, Wood drill and Stone/Concrete drill, with the MetavCUT Twist Drill belonging to the Metal drill category appropriate for ferrous and non‑ferrous metals.

Fehlinformation: Der angegebene Durchmesser 1,9 mm fällt in den Mikro-Bereich (0,05–2,0 mm), der für Präzisionsarbeiten vorgesehen ist und nicht für handgeführte Maschinen, widerspricht jedoch der Angabe "Für Bohrmaschine: Handbohrmaschine". Solche kleinen Durchmesser werden üblicherweise in spezialisierten Anwendungen eingesetzt, bei denen eine hohe Genauigkeit erforderlich ist, wie beispielsweise in der Feinmechanik oder der Schmuckherstellung. Die Verwendung in einer handgeführten Bohrmaschine könnte aufgrund der fehlenden Stabilität und Präzision problematisch sein. Daher ist die Kombination dieser Spezifikationen fragwürdig und sollte genauer überprüft werden, um sicherzustellen, dass die Angaben korrekt und für den vorgesehenen Verwendungszweck geeignet sind. Fehlinformation: Der angegebene Durchmesser 1,9 mm fällt in den Mikro‑Bereich (0,05–2,0 mm) und widerspricht der Angabe "Für Bohrmaschine: Handbohrmaschine". Solche Miniatur‑Durchmesser sind für Präzisionsarbeiten gedacht und nicht für den Einsatz in handgeführten Maschinen geeignet.

Twist Drill — Type N, 1.9 mm, 118°, 5% cobalt-alloyed, short, HSS‑E, DIN 338 The Twist Drill Type N is a short HSS‑E metal drilling bit designed for precise work in steels and non‑ferrous metals with a 118° point angle for controlled penetration. Short design for high stability and accuracy 5% cobalt‑alloyed HSS‑E for extended life Fully ground shaft for superior concentricity Conforms to DIN 338 for short twist drills Ideal for Drilling Machine applications Durable alloy and longer lifetime for metalworking The short HSS‑E cutting tool combines a 5% cobalt‑alloyed composition with a roll‑formed and ground geometry to deliver increased heat resistance and wear life when machining Steel and Cast Iron. Because the metal matrix contains additional cobalt, the bit retains hardness at elevated Temperatures, which reduces flank wear during extended Drilling operations. This construction translates into fewer tool changes and more consistent hole quality for workshop and production environments. Short length for superior stability and precise holes A reduced overall length means less overhang from the chuck and therefore significantly improved Stability and concentricity under load. The shorter cantilever minimizes vibration and the risk of deviation, so each hole is truer and cleaner. For applications where accuracy matters—jigs, fixture work and thin‑section components—the compact format ensures safer handling and lower breakage risk compared with longer equivalents. Geometry tuned for metal and controlled entry The 118° point angle and classic Type N spiral make this Short Twist Drill particularly suitable for general Metalworking, enabling controlled entry and good centring on flat surfaces. The fully ground flute geometry produces sharp cutting lips and a precise chisel edge, yielding clean holes with reduced burr. For tasks in alloyed and unalloyed Steel, non‑ferrous Metals and Plastics, this design balances penetration and tool life. Practical handling and maintenance advice To maximise service life, use moderated cutting speeds and adequate coolant when drilling hard or heat‑sensitive Materials. The fully ground shaft offers excellent run‑out characteristics in collets and chucks, but requires proper clamping to avoid slippage. When resharpening is necessary, observe the original point angle and maintain flute geometry to preserve Performance. For bench and machine use, the shorter length reduces bending stresses and simplifies chip evacuation. Choose the MetavCUT short Twist Drill for demanding metal applications — METAV Werkzeuge provides expert advice and technical support via eMail: info@metav-werkzeuge.com, Phone: +49 2822 7131930 and WhatsApp: +49 170 2837271 Designation: Twist Drill (Short) Brand: MetavCUT SKU: 47019-FDA Diameter: 1.9 mm Total length: 46 mm Spiral length: 22 mm Point angle: 118° Type: Type N Execution: short Colour: 5% cobalt-alloyed Shaft finish: fully ground Material: HSS-E Standard: DIN 338 For drilling machine: Drilling Machine Application: Drills for metal Model series: Standard Line Packaging unit: 10 Manufacturer: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What is the main use of this Twist Drill from MetavCUT Type N? The MetavCUT Twist Drill Type N is primarily used for machining high‑strength materials and larger drill diameters in Metalworking. Its short design improves stability and precision, and the 5% cobalt content helps the bit withstand higher Temperatures and mechanical stress during demanding drilling tasks. Which three drill types are commonly distinguished? Common drill categories are Metal drill (such as the MetavCUT Twist Drill Type N), Wood drill, and Stone/Concrete drill. Each is optimised for its material class and must be selected according to the workpiece to ensure proper hole quality and tool life. Why are Twist Drills sharpened at the tip? Sharpening the tip reduces the cross‑cutting edge area at the Twist Drill point, lowering friction. By reducing Reibkräfte, less thrust is required during drilling and the bit centres more reliably in the workpiece. Can a metal drill be used to drill wood? A Metal drill like the MetavCUT Twist Drill can be used in Wood, but guidance and surface finish are generally inferior compared with dedicated Wood drills. Metal drills are easier to resharpen and tend to produce less self‑feed, so careful feed control is recommended.

Twist Drill — Short HSS‑G Metal Drill, 1.9 mm, 118° Tip, Type N, Bright Finished, Short Execution, DIN 338 The Twist Drill is a short HSS‑G Type N metal drill designed for precise drilling in metal on a Drilling Machine and suitable for demanding workshop and industrial applications. Short HSS‑G design for higher stability 1.9 mm diameter for fine, precise holes 118° tip angle for reliable centering in metals Fully ground shank for high concentricity Conforms to DIN 338 for short twist drills Durable Material for Consistent Results and Longer Tool Life Made from HSS‑G, this short Twist Drill delivers high hardness and sharp cutting edges that produce clean holes in Metal. The ground flute geometry ensures excellent chip evacuation and reduces friction, which benefits tool life. Because the drill is manufactured with a CNC grinding process rather than roll forming, users gain high Rundlaufgenauigkeit and precise hole quality, especially important when working with alloys or cast materials. Short Design That Improves Stability and Precision at the Cut A shorter overall length reduces overhang and increases stability during drilling, which decreases the tendency to wander or bend under load. The short execution is particularly advantageous when drilling in hard Materials such as Steel, Cast Iron and Tempered Alloys, providing better concentricity and less vibration. This design therefore enables more consistent hole diameters and improved surface finish even under higher cutting forces. Geometry and Cutting Behaviour Optimised for Metalworking The 118° tip angle and Type N spiral geometry represent the classic metalworking configuration, supporting good centering and controlled chip formation. The sharpened tip reduces quench forces at initial contact and helps avoid skidding on curved surfaces. The fully ground shank and flute profile facilitate accurate clamping and runout behaviour, which is essential for demanding assembly or precision manufacturing tasks. Who Benefits and How to Use This Tool Effectively Designed for machinists and metalworkers, the Profi Line Twist Drill from MetavCUT is ideal for tasks requiring fine diameters and repeatable accuracy. Use on fixed or portable Drilling Machines with appropriate coolant for long tool life; the shorter geometry suits tight setups or jig work. For less experienced users, coolant and moderate spindle speeds are recommended to reduce heat and prolong cutting edge life. Highly recommended: choose the MetavCUT Profi Line Twist Drill for precision metal drilling and contact METAV Werkzeuge for expert advice and technical support — eMail: info@metav-werkzeuge.com • Phone: +49 2822 7131930 • WhatsApp: +49 170 2837271 Technical information Designation: Twist Drill Brand/Manufacturer: MetavCUT SKU: 48019-FDA Diameter: 1.9 mm Tip angle: 118° Type: Type N (Normal Spiral) Colour: Bright finished Execution: Short Material: HSS-G (Ground) Standard: DIN 338 Overall length: 49 mm Spiral length: 24 mm Shank finish: Fully ground Suitable for: Drilling Machine / Hand Drills for Metal applications Series: Profi Line Manufacturer: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ Can the MetavCUT Twist Drill be used in a hand drill as well as a drilling machine? The MetavCUT Twist Drill (Type N, HSS‑G) is primarily optimised for use on a Drilling Machine to ensure low runout and consistent cooling, but it can also be used in a Hand Drill if the chuck provides secure clamping and the correct speeds and coolant are applied to avoid overheating. Is the MetavCUT Twist Drill suitable for drilling alloyed steels? Yes, the MetavCUT Twist Drill from the Profi Line is suitable for alloyed and unalloyed Steel, Cast Iron and other Metals; its ground HSS‑G geometry gives sharp cutting edges that perform well in such Materials when used with appropriate feeds and coolant. What are Twist Drills used for? Twist Drills are mainly used for machining high‑strength Materials and larger hole diameters; this form is easy to regrind and withstands higher loads, making it suitable for demanding applications in Metalworking. Which three drill types exist? The main drill types are Metal Drills, Wood Drills and Masonry/Concrete Drills.

Spiralbohrer (HSS‑G, Ø 10,2 mm, 135°, geschliffen, reduziert 10 mm Schaft, silber, DIN 338) von MetavCUT Der Spiralbohrer von MetavCUT ist ein geschliffener HSS‑G Bohrer für präzise Metallbearbeitung an stationären und handgeführten Maschinen. Geschliffen HSS‑G für präzise Metallbohrungen Durchmesser 10,2 mm für Standardanwendungen Spitzenwinkel 135° für harte Werkstoffe Reduzierter Schaft 10 mm für kleinere Bohrfutter Norm DIN 338 und Gesamtlänge 133 mm Höhere Leistung mit weniger Kraftaufwand für effizientes Arbeiten Der geschliffene HSS‑G Bohrer liefert spürbar mehr Effizienz beim Bohren in Metall. Durch den CNC‑Schliff entsteht eine sehr scharfe Schneide, die ein bis zu 40 % schnelleres Bohren ermöglicht und gleichzeitig 50 % weniger Anpresskraft benötigt. Für den Durchmesser 10,2 mm bedeutet das schnellere Arbeitszyklen und weniger Ermüdung bei wiederholten Bohrungen, was in Montage und Serienarbeiten die Produktivität erhöht. Flexibilität in Werkstatt und Produktion bei kontrolliertem Einsatz Dieser Bohrer ist für den typischen Einsatz im Standard‑Bereich konzipiert und passt zu Werkstatt, Montage und vielen DIY‑Aufgaben. Dank des reduzierten Schafts 10 mm lässt sich der Bohrer auch in Bohrfuttern mit begrenzter Spannweite einsetzen. Für beste Ergebnisse empfiehlt sich der Einsatz in stationären Maschinen oder in handgeführten Geräten mit ruhigem Rundlauf; bei längeren Einsätzen sorgt Kühlung für konstante Leistung und längere Standzeiten. Materialeigenschaften erklären: warum „geschliffen“ einen Unterschied macht Bei einem geschliffenen Spiralbohrer werden die Spannuten und die Geometrie per Schleifprozess erzeugt, was besonders saubere und präzise Bohrlöcher liefert. Der Begriff geschliffen steht für hohe Rundlaufgenauigkeit und sehr scharfe Kanten, ideal für legierte und unlegierte Stähle, Gusseisen sowie Nichteisenmetalle. Der Spitzenwinkel 135° reduziert Anlaufwanderung und ist speziell vorteilhaft beim Bohren von harten Werkstoffen wie Edelstahl, da er die Anbohrzeit verkürzt und das Eindringen erleichtert. Zielgruppe und Einsatzempfehlung für langlebige Ergebnisse Entwickelt wurde der Bohrer für Anwender in Werkstatt, Instandhaltung und Produktion, die Wert auf saubere Bohrbilder und reproduzierbare Ergebnisse legen. Der Spiralbohrer eignet sich für die Bearbeitung von Baustahl, Aluminium, Hartkunststoff und Temperguss; bei sehr tiefen Löchern oder extrem zähen Werkstoffen empfiehlt sich praxiserprobtes Vorbohren oder der Einsatz spezieller Vollhartmetallwerkzeuge. Die Norm DIN 338 gibt die kurzen Spiralbohrer mit Zylinderschaft vor und stellt die Kompatibilität mit gängigen Spannsystemen sicher. Mit dem MetavCUT Spiralbohrer in HSS‑G werden Metallbohrungen effizienter und präziser ausgeführt — bei Unsicherheit zur Eignung oder für zusätzliche technische Daten berät METAV Werkzeuge persönlich per eMail info@metav-werkzeuge.com oder Telefon +49 2822 7131930 Bezeichnung: Spiralbohrer Marke: MetavCUT SKU: 63102-FDA Durchmesser: 10,2 mm Material: HSS‑G Ausführung: geschliffen Farbe: silber Spitzenwinkel: 135° Schaft Ausführung: reduziert 10 mm Gesamtlänge: 133 mm Spirallänge: 87 mm Norm: DIN 338 Modellserie: Standard Line Anwendung: Bohrer für Metall Hersteller: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ Ist der MetavCUT Spiralbohrer für Edelstahl geeignet? Der MetavCUT Spiralbohrer mit Spitzenwinkel 135° ist besonders geeignet für härtere Werkstoffe wie Edelstahl; bei längeren Bohrungen empfiehlt sich Kühlung, um die Standzeit des Bohrers zu erhöhen. Kann der Spiralbohrer in handgeführten Akkuschraubern verwendet werden? Der MetavCUT Spiralbohrer kann in handgeführten Geräten eingesetzt werden, sofern das Bohrfutter sicheren Rundlauf bietet; für höchste Präzision und Standzeit ist jedoch die Nutzung in stationären Maschinen zu empfehlen. Warum ist der Bohrer geschliffen und welche Vorteile bringt das? Ein geschliffener MetavCUT Spiralbohrer bietet höhere Rundlaufgenauigkeit und sehr scharfe Kanten, was zu saubereren Bohrlöchern und höherer Vorschubleistung führt; der Schliff kann jedoch die Sprödigkeit erhöhen, weshalb kontrollierte Maschinenführung und Kühlung sinnvoll sind. Wofür ist der reduzierte Schaft 10 mm praktisch? Der reduzierte Schaft 10 mm des MetavCUT Spiralbohrers ermöglicht das Spannen in Bohrfuttern mit kleinerer Spannweite, sodass größerdimensionale Bohrer auch in begrenzten Spannsystemen genutzt werden können. {"@context":"https://schema.org","@graph":[{"@type":"Product","@id":"#63102-FDA","sku":"63102-FDA","mpn":"63102-FDA","name":"Spiralbohrer 63102-FDA","description":"Geschliffener HSS‑G Spiralbohrer Ø 10,2 mm, Spitzenwinkel 135°, reduziert 10 mm Schaft, silber, DIN 338; Für präzise Metallbohrungen in Werkstatt und Produktion; Hohe Rundlaufgenauigkeit durch CNC‑Schliff; Geeignet für Baustahl, Edelstahl, Gusseisen, Nichteisenmetalle und Hartkunststoff.","image":["https://files.plytix.com/api/v1.1/file/public_files/pim/assets/57/c3/98/62/6298c3575d155f1bc7e497fd/images/8e/48/c5/69/69c5488eb2b3400ba580741b/logo-metav-1200-1200.png","https://files.plytix.com/api/v1.1/file/public_files/pim/assets/57/c3/98/62/6298c3575d155f1bc7e497fd/images/8e/48/c5/69/69c5488eb2b3400ba580741e/logo-metav-1200-900.png","https://files.plytix.com/api/v1.1/file/public_files/pim/assets/57/c3/98/62/6298c3575d155f1bc7e497fd/images/8e/48/c5/69/69c5488eb2b3400ba580741c/logo-metav-1200-675.png"],"additionalProperty":[{"@type":"PropertyValue","name":"Bezeichnung","value":"Spiralbohrer"},{"@type":"PropertyValue","name":"Marke","value":"MetavCUT"},{"@type":"PropertyValue","name":"Durchmesser","value":"10,2 mm"},{"@type":"PropertyValue","name":"Material","value":"HSS-G"},{"@type":"PropertyValue","name":"Ausführung","value":"geschliffen"},{"@type":"PropertyValue","name":"Farbe","value":"silber"},{"@type":"PropertyValue","name":"Spitzenwinkel","value":"135°"},{"@type":"PropertyValue","name":"Schaft Ausführung","value":"reduziert 10 mm"},{"@type":"PropertyValue","name":"Gesamtlänge","value":"133 mm"},{"@type":"PropertyValue","name":"Spirallänge","value":"87 mm"},{"@type":"PropertyValue","name":"Norm","value":"DIN 338"},{"@type":"PropertyValue","name":"Modellserie","value":"Standard Line"},{"@type":"PropertyValue","name":"Anwendung","value":"Bohrer für Metall"},{"@type":"PropertyValue","name":"Hersteller","value":"Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com"}]},{"@type":"FAQPage","mainEntity":[{"@type":"Question","name":"Ist der MetavCUT Spiralbohrer für Edelstahl geeignet?","acceptedAnswer":{"@type":"Answer","text":"Der MetavCUT Spiralbohrer Ø 10,2 mm mit Spitzenwinkel 135° ist besonders geeignet für härtere Werkstoffe wie Edelstahl; bei längeren Bohrungen empfiehlt sich Kühlung, um die Standzeit zu erhöhen."}},{"@type":"Question","name":"Kann der Spiralbohrer in handgeführten Geräten verwendet werden?","acceptedAnswer":{"@type":"Answer","text":"Der MetavCUT Spiralbohrer kann in handgeführten Geräten eingesetzt werden, sofern das Bohrfutter sicheren Rundlauf bietet; für höchste Präzision und Standzeit wird die Nutzung in stationären Maschinen empfohlen."}},{"@type":"Question","name":"Warum ist der Spiralbohrer geschliffen und welche Vorteile bringt das?","acceptedAnswer":{"@type":"Answer","text":"Ein geschliffener HSS‑G Spiralbohrer bietet hohe Rundlaufgenauigkeit und sehr scharfe Kanten, was zu sauberen Bohrlöchern und höherer Vorschubleistung führt; Nachteil: erhöhte Sprödigkeit, daher kontrollierte Maschinenführung und Kühlung sinnvoll."}},{"@type":"Question","name":"Wofür ist der reduzierte Schaft 10 mm praktisch?","acceptedAnswer":{"@type":"Answer","text":"Der reduzierte Schaft 10 mm des MetavCUT Spiralbohrers ermöglicht das Spannen in Bohrfuttern mit kleinerer Spannweite, sodass größere Bohrer in begrenzten Spannsystemen genutzt werden können."}}]},{"@type":"ItemPage","url":"https://metav-shop.de/produkt/63102-FDA","dateModified":"2026-05-04T12:00:00+01:00","author":{"@type":"Person","name":"Stephan Bayer","url":"https://www.linkedin.com/in/stephan-bayer/"},"publisher":{"@type":"Organization","name":"Metav Werkzeuge GmbH","url":"https://metav-shop.de","logo":{"@type":"ImageObject","url":"https://files.plytix.com/api/v1.1/file/public_files/pim/assets/57/c3/98/62/6298c3575d155f1bc7e497fd/images/8e/48/c5/69/69c5488eb2b3400ba580741c/logo-metav-1200-675.png","width":1200,"height":675},"address":{"@type":"PostalAddress","streetAddress":"Parkring 45","postalCode":"46446","addressLocality":"Emmerich","addressCountry":"DE"},"telephone":"+49 2822 7131930","email":"info@metav-werkzeuge.com"},"about":[{"@type":"Thing","name":"Spiralbohrer HSS-G"},{"@type":"Thing","name":"Standard Line"},{"@type":"Thing","name":"DIN 338"}],"mentions":[{"@type":"Thing","name":"reduzierter Schaft 10 mm"},{"@type":"Thing","name":"Spitzenwinkel 135°"},{"@type":"Thing","name":"geschliffen (HSS-G)"}]}]}

Spiralbohrer (Typ N, HSS, 10,5 mm, 118°, schwarz, rollgewalzt, DIN 338) Der Spiralbohrer von MetavCUT ist ein rollgewalzter HSS-Bohrer (Typ N) mit reduziertem Schaft 10 mm, ausgelegt für zuverlässige Metallbohrungen in Werkstatt und Montage. Rollgewalzte Ausführung für erhöhte Bruchsicherheit HSS-Material: geeignet für legierten und unlegierten Stahl Spitzenwinkel 118° für sauberes Zentrieren in Metall Reduzierter Schaft 10 mm passt in kleinere Bohrfutter DIN 338 Norm: kurzer Spiralbohrer mit Zylinderschaft Zähigkeit und Robustheit für den Werkstattalltag Dank der rollgewalzten Fertigung zeichnet sich dieser Bohrer durch hohe Zähigkeit und verminderte Bruchgefahr aus. Die Herstellung durch Walzen macht den HSS-Stab elastischer, wodurch das Risiko eines sofortigen Bruchs bei leichten Verkippungen reduziert wird. Für Anwender bedeutet das weniger Stillstand durch beschädigte Werkzeuge und eine längere Nutzungsdauer bei normalen Metallarbeiten. Effiziente Metallbearbeitung mit klarer Anwendungsempfehlung Der Typ N Normalspirale eignet sich besonders für die Bearbeitung von Stahl, Gusseisen sowie Nichteisenmetallen und Kunststoffen. Durch die Einordnung in die DIN 338 ist der Bohrer als kurzer Spiralbohrer mit Zylinderschaft klassifiziert und erfüllt die Anforderungen für viele Standardaufgaben in Werkstatt und Montage. Für höhere Präzision empfiehlt sich vorheriges Zentrieren mit einem Anreiß- oder Zentrierbohrer. Einfache Handhabung dank reduziertem Schaft und praxisgerechter Abmessung Weil der Schaft auf 10 mm reduziert ist, lässt sich der Bohrer auch in Bohrfuttern mit kleinerem Spannbereich einsetzen, ohne auf einen größeren Bohrdurchmesser verzichten zu müssen. Die Gesamtlänge von 133 mm und die Spirallänge von 87 mm bieten ausreichend Ausladung für durchgehende Bohrungen, während die schwarze Oberfläche die optische Unterscheidung im Werkzeugsortiment erleichtert. Für welche Anwender dieses Werkzeug ideal ist Handwerkliche Betriebe, Montage-Teams und anspruchsvolle Heimwerker profitieren von der Kombination aus Robustheit und universeller Einsetzbarkeit. Die Standard Line von MetavCUT richtet sich an Nutzer, die verlässliche Werkzeuge für den täglichen Einsatz wünschen, ohne auf professionelle Materialkompatibilität verzichten zu müssen. Greifen Sie zur MetavCUT Standard Line, wenn eine zähe, bruchsichere Lösung für zuverlässige Metallbohrungen gefragt ist; bei Fragen stehen Ihnen METAV Werkzeuge per eMail info@metav-werkzeuge.com oder Telefon +49 2822 7131930 zur Verfügung Bezeichnung: Spiralbohrer Marke: MetavCUT SKU: 61105-FDA Durchmesser: 10,5 mm Material: HSS Ausführung: rollgewalzt Typ: Typ N Spitzenwinkel: 118° Farbe: schwarz Schaftausführung: reduziert 10 mm Gesamtlänge: 133 mm Spirallänge: 87 mm Norm: DIN 338 Modellserie: Standard Line Hersteller: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ Ist der Spiralbohrer von MetavCUT (Typ N) für legierten Stahl geeignet? Der Spiralbohrer von MetavCUT (Typ N) aus HSS eignet sich für das Bohren in legierten und unlegierten Stahl; bei hohen Anforderungen an Maßhaltigkeit empfiehlt sich zusätzlich ein Zentrierbohrer. Kann der Spiralbohrer 10,5 mm in einem 10-mm-Bohrfutter verwendet werden? Ja, dank des reduzierten Schafts 10 mm lässt sich der Spiralbohrer von MetavCUT in kleineren Bohrfuttern spannen, wodurch größere Bohrdurchmesser auch in engeren Spannbereichen möglich sind. Welche Vorteile bietet die rollgewalzte Ausführung des Spiralbohrers von MetavCUT? Die rollgewalzte Fertigung macht den Spiralbohrer von MetavCUT zäher und weniger bruchanfällig, was besonders bei Standardaufgaben in Werkstatt und Montage von Vorteil ist. Brauche ich bei Einsatz des Spiralbohrers von MetavCUT besondere Kühlschmierstoffe? Für den Spiralbohrer von MetavCUT wird bei Stahlbohrungen der Einsatz geeigneter Kühlschmierstoffe empfohlen, um Standzeit zu erhöhen und Maßhaltigkeit zu unterstützen; bei weichen Materialien ist manchmal trockenes Bohren ausreichend. {"@context":"https://schema.org","@graph":[{"@type":"Product","@id":"#61105-FDA","sku":"61105-FDA","mpn":"61105-FDA","name":"Spiralbohrer 10,5 mm","description":"Rollgewalzter HSS Spiralbohrer Typ N, Durchmesser 10,5 mm, Spitzenwinkel 118°, schwarz, reduziertem Schaft 10 mm, Norm DIN 338; geeignet für Metallbohrungen in Werkstatt und Montage; zähe, bruchsichere Ausführung für legierten und unlegierten Stahl sowie Gusseisen, Nichteisenmetalle und Kunststoffe.","image":["https://files.plytix.com/api/v1.1/file/public_files/pim/assets/57/c3/98/62/6298c3575d155f1bc7e497fd/images/8e/48/c5/69/69c5488eb2b3400ba580741b/logo-metav-1200-1200.png","https://files.plytix.com/api/v1.1/file/public_files/pim/assets/57/c3/98/62/6298c3575d155f1bc7e497fd/images/8e/48/c5/69/69c5488eb2b3400ba580741e/logo-metav-1200-900.png","https://files.plytix.com/api/v1.1/file/public_files/pim/assets/57/c3/98/62/6298c3575d155f1bc7e497fd/images/8e/48/c5/69/69c5488eb2b3400ba580741c/logo-metav-1200-675.png"],"additionalProperty":[{"@type":"PropertyValue","name":"Bezeichnung","value":"Spiralbohrer"},{"@type":"PropertyValue","name":"Marke","value":"MetavCUT"},{"@type":"PropertyValue","name":"SKU","value":"61105-FDA"},{"@type":"PropertyValue","name":"Durchmesser","value":"10,5 mm"},{"@type":"PropertyValue","name":"Material","value":"HSS"},{"@type":"PropertyValue","name":"Ausführung","value":"rollgewalzt"},{"@type":"PropertyValue","name":"Typ","value":"Typ N"},{"@type":"PropertyValue","name":"Spitzenwinkel","value":"118°"},{"@type":"PropertyValue","name":"Farbe","value":"schwarz"},{"@type":"PropertyValue","name":"Schaftausführung","value":"reduziert 10 mm"},{"@type":"PropertyValue","name":"Gesamtlänge","value":"133 mm"},{"@type":"PropertyValue","name":"Spirallänge","value":"87 mm"},{"@type":"PropertyValue","name":"Norm","value":"DIN 338"},{"@type":"PropertyValue","name":"Modellserie","value":"Standard Line"},{"@type":"PropertyValue","name":"Anwendung","value":"Bohrer für Metall"},{"@type":"PropertyValue","name":"Hersteller","value":"Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com"}]},{"@type":"FAQPage","mainEntity":[{"@type":"Question","name":"Ist der Spiralbohrer 10,5 mm von MetavCUT für legierten Stahl geeignet?","acceptedAnswer":{"@type":"Answer","text":"Der Spiralbohrer 10,5 mm von MetavCUT aus HSS und rollgewalzter Ausführung eignet sich für legierten und unlegierten Stahl; für hohe Maßhaltigkeit empfiehlt sich vorheriges Zentrieren."}},{"@type":"Question","name":"Lässt sich der Spiralbohrer 10,5 mm von MetavCUT in einem 10 mm Bohrfutter verwenden?","acceptedAnswer":{"@type":"Answer","text":"Ja, der Spiralbohrer 10,5 mm von MetavCUT verfügt über einen reduzierten Schaft 10 mm, sodass er in Bohrfuttern mit kleinerem Spannbereich eingespannt werden kann."}},{"@type":"Question","name":"Welche Vorteile bietet die rollgewalzte Ausführung des Spiralbohrers 10,5 mm von MetavCUT?","acceptedAnswer":{"@type":"Answer","text":"Die rollgewalzte Fertigung macht den Spiralbohrer 10,5 mm von MetavCUT zäher und weniger bruchanfällig, was im Werkstattalltag zu längeren Standzeiten führt."}},{"@type":"Question","name":"Welche Materialien lassen sich mit dem Spiralbohrer 10,5 mm von MetavCUT bearbeiten?","acceptedAnswer":{"@type":"Answer","text":"Der Spiralbohrer 10,5 mm von MetavCUT eignet sich für Stahl, Gusseisen, Nichteisenmetalle und Kunststoffe; er ist für allgemeine Metallbearbeitung ausgelegt."}}]},{"@type":"ItemPage","url":"https://metav-shop.de/spiralbohrer-61105-FDA","dateModified":"2026-05-04T12:00:00+01:00","author":{"@type":"Person","name":"Stephan Bayer","url":"https://www.linkedin.com/in/stephan-bayer/"},"publisher":{"@type":"Organization","name":"Metav Werkzeuge GmbH","url":"https://metav-shop.de","logo":{"@type":"ImageObject","url":"https://files.plytix.com/api/v1.1/file/public_files/pim/assets/57/c3/98/62/6298c3575d155f1bc7e497fd/images/8e/48/c5/69/69c5488eb2b3400ba580741c/logo-metav-1200-675.png","width":1200,"height":675},"address":{"@type":"PostalAddress","streetAddress":"Parkring 45","postalCode":"46446","addressLocality":"Emmerich","addressCountry":"DE"},"telephone":"+49 2822 7131930","email":"info@metav-werkzeuge.com"},"about":[{"@type":"Thing","name":"Spiralbohrer Standard Line"},{"@type":"Thing","name":"Rollgewalzte HSS Ausführung"},{"@type":"Thing","name":"DIN 338 kurzer Spiralbohrer"}],"mentions":[{"@type":"Thing","name":"reduzierter Schaft 10 mm"},{"@type":"Thing","name":"Spitzenwinkel 118°"},{"@type":"Thing","name":"Anwendung: Metallbohrung"}]}]}

Spiralbohrer 10,5 mm (HSS, rollgewalzt, Morsekegel, DIN 345) von MetavCUT Der Spiralbohrer 10,5 mm ist ein robuster HSS-Bohrer in rollgewalzter Ausführung, geeignet für präzise Metallbohrungen mit stationären Maschinen und Werkstattanwendungen. Spiralbohrer 10,5 mm für gängige Metallarbeiten HSS-Material für erhöhte Zähigkeit und Standzeit Rollgewalzte Ausführung reduziert Bruchrisiko Morsekegel-Schaft für sichere Aufnahme in Säulenbohrmaschinen DIN 345 Normkonform für industrielle Anwendungen Präzise Bohrungen in Stahl, Guss und NE-Metallen sichern Qualität und Effizienz Der Spiralbohrer aus HSS bietet eine ausgewogene Mischung aus Zähigkeit und Schnittfestigkeit, ideal für das Bohren in legierten und unlegierten Stählen sowie Gusswerkstoffen bis ca. 900 N/mm². Die Kombination aus Spitzenwinkel 118° und geeigneter Schnittgeometrie erleichtert das Eindringen in weiche bis mittlere Materialien und sorgt für saubere Spanabfuhr. Anwender profitieren von verlässlichen Ergebnissen bei Reparaturarbeiten, Maschineninstandsetzung und allgemeinen Werkstattaufgaben. Rollgewalztes Herstellverfahren erhöht Bruchsicherheit und Wirtschaftlichkeit Die rollgewalzte Fertigung macht den Bohrer elastischer und widerstandsfähiger gegen Axialbelastungen, was besonders bei Durchmessern um 10,5 mm das Risiko von Bruch reduziert. Im Vergleich zu geschliffenen Ausführungen resultiert das Walzverfahren in einem wirtschaftlicheren Produkt, das bei Standardaufgaben im Metallbereich eine langlebige Lösung darstellt. Für Anwender bedeutet das: weniger Werkstückausfälle und geringere Nacharbeit. Morsekegel-Schaft sorgt für kraftschlüssige Übertragung und sichere Montage Der konische Morsekegel-Schaft ermöglicht die direkte Aufnahme in Säulenbohrmaschinen und gewährleistet eine feste, selbsthemmende Verbindung zur Maschine. Dadurch wird hohes Drehmoment sicher übertragen und die Rundlaufgenauigkeit verbessert. Diese Eigenschaft macht den Bohrer besonders geeignet für stationäre Anwendungen im Maschinenbau, in Werkstätten und in der Metallinstandhaltung. Handhabung, Maße und Werkstatttauglichkeit optimieren den Arbeitsablauf Mit einer Gesamtlänge von 168 mm und einer Spirallänge von 87 mm eignet sich der Bohrer für normale Durchgangs- und Sacklochbohrungen bei üblichen Werkstückdicken. Die schwarze Oberfläche erleichtert die Identifikation im Werkzeugbestand, während die Einhaltung der DIN 345 klare Maß- und Qualitätsvorgaben für industrielle Prozesse garantiert. Anwender erhalten so ein zuverlässiges Werkzeug, das sich nahtlos in bestehende Fertigungsprozesse integriert. Empfehlung: Vertrauen Sie auf die MetavCUT Standard Line für langlebige Werkstattlösungen und kontaktieren Sie bei Fragen den kompetenten Beratungssupport von METAV Werkzeuge per eMail info@metav-werkzeuge.com oder Telefon +49 2822 7131930; WhatsApp +49 170 2837271 – wir helfen bei der Auswahl und technischen Prüfung gern weiter. Bezeichnung: Spiralbohrer Marke: MetavCUT SKU: 54105-FDA Durchmesser: 10,5 mm Material: HSS Ausführung: rollgewalzt Schaft Ausführung: Morsekegel Spitzenwinkel: 118° Gesamtlänge: 168 mm Spirallänge: 87 mm Farbe: schwarz Norm: DIN 345 Modellserie: Standard Line Anwendung: Bohrer für Metall Hersteller: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ Ist der Spiralbohrer 10,5 mm von MetavCUT für Baustahl geeignet? Der Spiralbohrer 10,5 mm von MetavCUT ist für Baustahl und andere Stähle bis ca. 900 N/mm² Festigkeit ausgelegt und eignet sich damit für viele Reparatur- und Montageaufgaben in Werkstatt und Maschinenbau. Kann der MetavCUT Spiralbohrer im Bohrfutter von Handmaschinen genutzt werden? Der MetavCUT Spiralbohrer mit Morsekegel-Schaft ist primär für stationäre Säulenbohrmaschinen gedacht; für Handgeführte Akkumaschinen empfiehlt sich eine zylindrische Schaftform oder ein Adapter. Wie erhöht die rollgewalzte Ausführung die Standzeit des HSS-Bohrers? Durch die rollgewalzte Fertigung bleibt der Werkstoff zäher und weniger bruchanfällig, wodurch der HSS-Bohrer von MetavCUT bei Standardbohrungen eine verbesserte Lebensdauer gegenüber sehr feingeschliffenen Varianten bieten kann. Welchen Einfluss hat der Spitzenwinkel 118° beim MetavCUT HSS-Bohrer? Der Spitzenwinkel 118° am MetavCUT HSS-Bohrer erleichtert das Zentrieren auf gewölbten oder weichen Oberflächen und ist daher gut geeignet für Aluminium und weichere Stähle, ohne die Spanabfuhr zu beeinträchtigen. {"@context":"https://schema.org","@graph":[{"@type":"Product","@id":"#54105-FDA","sku":"54105-FDA","mpn":"54105-FDA","name":"Spiralbohrer 10,5 mm","description":"Spiralbohrer 10,5 mm, HSS, rollgewalzt, Morsekegel, Spitzenwinkel 118°, Farbe schwarz, DIN 345; robuster Standardbohrer für Metallanwendungen bis ca. 900 N/mm², geeignet für Säulenbohrmaschinen; Gesamtlänge 168 mm, Spirallänge 87 mm.","image":["https://files.plytix.com/api/v1.1/file/public_files/pim/assets/57/c3/98/62/6298c3575d155f1bc7e497fd/images/8e/48/c5/69/69c5488eb2b3400ba580741b/logo-metav-1200-1200.png","https://files.plytix.com/api/v1.1/file/public_files/pim/assets/57/c3/98/62/6298c3575d155f1bc7e497fd/images/8e/48/c5/69/69c5488eb2b3400ba580741e/logo-metav-1200-900.png","https://files.plytix.com/api/v1.1/file/public_files/pim/assets/57/c3/98/62/6298c3575d155f1bc7e497fd/images/8e/48/c5/69/69c5488eb2b3400ba580741c/logo-metav-1200-675.png"],"additionalProperty":[{"@type":"PropertyValue","name":"Bezeichnung","value":"Spiralbohrer"},{"@type":"PropertyValue","name":"Marke","value":"MetavCUT"},{"@type":"PropertyValue","name":"Durchmesser","value":"10,5 mm"},{"@type":"PropertyValue","name":"Material","value":"HSS"},{"@type":"PropertyValue","name":"Ausführung","value":"rollgewalzt"},{"@type":"PropertyValue","name":"Schaft Ausführung","value":"Morsekegel"},{"@type":"PropertyValue","name":"Spitzenwinkel","value":"118°"},{"@type":"PropertyValue","name":"Gesamtlänge","value":"168 mm"},{"@type":"PropertyValue","name":"Spirallänge","value":"87 mm"},{"@type":"PropertyValue","name":"Farbe","value":"schwarz"},{"@type":"PropertyValue","name":"Norm","value":"DIN 345"},{"@type":"PropertyValue","name":"Modellserie","value":"Standard Line"},{"@type":"PropertyValue","name":"Anwendung","value":"Bohrer für Metall"},{"@type":"PropertyValue","name":"Preis Netto","value":"7.84"},{"@type":"PropertyValue","name":"Hersteller","value":"Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com"}]},{"@type":"FAQPage","mainEntity":[{"@type":"Question","name":"Ist der Spiralbohrer 10,5 mm von MetavCUT für Baustahl geeignet?","acceptedAnswer":{"@type":"Answer","text":"Der Spiralbohrer 10,5 mm von MetavCUT ist für Baustahl und andere Stähle bis ca. 900 N/mm² Festigkeit ausgelegt und eignet sich damit für viele Reparatur- und Montageaufgaben in Werkstatt und Maschinenbau."}},{"@type":"Question","name":"Kann der MetavCUT Spiralbohrer im Bohrfutter von Handmaschinen genutzt werden?","acceptedAnswer":{"@type":"Answer","text":"Der MetavCUT Spiralbohrer 10,5 mm mit Morsekegel-Schaft ist primär für stationäre Säulenbohrmaschinen gedacht; für handgeführte Akkumaschinen empfiehlt sich eine zylindrische Schaftform oder ein Adapter."}},{"@type":"Question","name":"Wie erhöht die rollgewalzte Ausführung die Standzeit des HSS-Bohrers?","acceptedAnswer":{"@type":"Answer","text":"Durch die rollgewalzte Fertigung bleibt der Werkstoff zäher und weniger bruchanfällig, wodurch der HSS-Spiralbohrer 10,5 mm von MetavCUT bei Standardbohrungen eine verbesserte Lebensdauer gegenüber sehr feingeschliffenen Varianten bieten kann."}},{"@type":"Question","name":"Welchen Einfluss hat der Spitzenwinkel 118° beim MetavCUT HSS-Bohrer?","acceptedAnswer":{"@type":"Answer","text":"Der Spitzenwinkel 118° am MetavCUT HSS-Spiralbohrer 10,5 mm erleichtert das Zentrieren auf gewölbten oder weichen Oberflächen und eignet sich gut für Aluminium und weichere Stähle, ohne die Spanabfuhr zu beeinträchtigen."}}]},{"@type":"ItemPage","url":"https://metav-shop.de/spiralbohrer-10-5-mm-54105-FDA","dateModified":"2026-05-04T12:00:00+01:00","author":{"@type":"Person","name":"Stephan Bayer","url":"https://www.linkedin.com/in/stephan-bayer/"},"publisher":{"@type":"Organization","name":"Metav Werkzeuge GmbH","url":"https://metav-shop.de","logo":{"@type":"ImageObject","url":"https://files.plytix.com/api/v1.1/file/public_files/pim/assets/57/c3/98/62/6298c3575d155f1bc7e497fd/images/8e/48/c5/69/69c5488eb2b3400ba580741c/logo-metav-1200-675.png","width":1200,"height":675},"address":{"@type":"PostalAddress","streetAddress":"Parkring 45","postalCode":"46446","addressLocality":"Emmerich","addressCountry":"DE"},"telephone":"+49 2822 7131930","email":"info@metav-werkzeuge.com"},"about":[{"@type":"Thing","name":"Spiralbohrer Standard Line"},{"@type":"Thing","name":"HSS rollgewalzt für Metall"},{"@type":"Thing","name":"Morsekegel-Schaft für Säulenbohrmaschinen"}],"mentions":[{"@type":"Thing","name":"DIN 345 Norm"},{"@type":"Thing","name":"Spitzenwinkel 118°"},{"@type":"Thing","name":"Geeignet für Stähle bis 900 N/mm²"}]}]}

Spiralbohrer 10,5 mm — HSS‑G, geschliffen, reduziert 10 mm Schaft, 135°, silber, DIN 338 von MetavCUT Der Spiralbohrer ist ein geschliffener HSS‑Bohrer für präzise Metallbearbeitung an stationären und mobilen Maschinen und eignet sich besonders für legierte und unlegierte Stähle sowie Nichteisenmetalle. Geschliffene Geometrie für hohe Präzision HSS‑G: belastbar bei Metallbearbeitung Reduzierter Schaft 10 mm für enge Bohrfutter Spitzenwinkel 135° für härtere Werkstoffe DIN 338: kurze Spiralbohrer mit Zylinderschaft Effiziente Metallbearbeitung durch geschliffene HSS‑Geometrie Geschliffene Bohrer aus HSS‑G bieten eine deutlich höhere Schneidqualität als gewalzte Varianten. Die geschliffene Schneidengeometrie sorgt für scharfe Kanten und präzise Bohrlöcher, wodurch sich die Bearbeitungszeit reduziert und die Nacharbeit minimiert wird. Für Anwender bedeutet das: schnellere Prozesse bei gleichbleibender Werkstückqualität und geringerer Kraftaufwand beim Vorschub. Warum die Schleifung den Unterschied macht Bei einem geschliffenen Spiralbohrer werden Spannuten und Schnittgeometrie per Schleifen (CNC‑Schliff) in den Rohling eingearbeitet. Das Ergebnis ist ein konstanter Rundlauf und saubere Spanabfuhr bei mittleren Schnitttiefen. Gleichzeitig kann die Sprödigkeit zunehmen; deshalb empfiehlt sich der Einsatz mit geeigneter Kühlung und bei Bedarf an stationären Maschinen, um Bruchrisiken zu minimieren. Passende Einsätze und Maschinen für den Einsatzbereich Der Bohrdurchmesser von 10,5 mm liegt im Standard‑Bereich, wodurch der Einsatz in Werkstätten, Montage und bei DIY‑Projekten optimiert ist. Der reduzierte Schaft 10 mm erlaubt das Spannen in Bohrfuttern mit 10 mm Aufnahme, während die Ausführung nach DIN 338 den Einsatz an Säulenbohrmaschinen und handgeführten Geräten erleichtert. Für beste Ergebnisse empfiehlt sich bei hoher Präzision ein Anpunkten vor dem Bohrvorgang. Praktische Hinweise zu Anwendung und Standzeit Für saubere Ergebnisse empfiehlt sich die Verwendung von Kühlschmierstoff und moderaten Schnittparametern, besonders bei harten Werkstoffen. Der Spitzenwinkel 135° reduziert das Wanderverhalten beim Anbohren harter Materialien und verkürzt die Anbohrzeit. Vermeiden Sie tiefe Sacklochbohrungen ohne geeignete Spanabfuhr; bei Bedarf in mehreren Schritten aufbohren, um Spanstau und Überhitzung zu verhindern. Für präzise Metallbohrungen empfehlen wir den geschliffenen HSS‑G Spiralbohrer von MetavCUT; bei Fragen zur Anwendung oder zur Auswahl des passenden Bohrers berät das Team von METAV Werkzeuge gern per E‑Mail: info@metav-werkzeuge.com oder Telefon: +49 2822 7131930; WhatsApp: +49 170 2837271 Bezeichnung: Spiralbohrer Marke/Hersteller: MetavCUT SKU: 63105-FDA Durchmesser: 10,5 mm Spitzenwinkel: 135° Ausführung: geschliffen Material: HSS‑G Farbe: silber Gesamtlänge: 133 mm Spirallänge: 87 mm Schaft Ausführung: reduziert 10 mm Norm: DIN 338 Modellserie: Standard Line Anwendung: Bohrer für Metall Hersteller: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ Wie eignet sich der Spiralbohrer von MetavCUT für Edelstahl? Der Spiralbohrer von MetavCUT in HSS‑G mit 135° Spitzenwinkel ist für härtere Werkstoffe wie Edelstahl geeignet; es wird jedoch empfohlen, mit Kühlschmierstoff und moderaten Vorschubwerten zu arbeiten, um Überhitzung und Verschleiß zu reduzieren. Kann der Spiralbohrer von MetavCUT in einem 10 mm Bohrfutter verwendet werden? Ja, durch den reduzierten Schaft 10 mm lässt sich der Spiralbohrer von MetavCUT in Bohrfutter mit 10 mm Aufnahme spannen, wodurch größere Bohrdurchmesser auch in begrenzten Aufnahmen möglich werden. Ist der geschliffene Spiralbohrer von MetavCUT für Handbohrmaschinen geeignet? Der Spiralbohrer von MetavCUT arbeitet im Standard‑Bereich und kann in handgeführten Akkubohrschraubern eingesetzt werden; für höchste Präzision und zur Reduzierung des Bruchrisikos empfiehlt sich jedoch eine stationäre Maschine und ausreichende Kühlung. Wo bekomme ich weitere Beratung zur Anwendung des Spiralbohrers von MetavCUT? Sollten Unsicherheiten bestehen, steht METAV Werkzeuge mit technischer Beratung zur Verfügung; kontaktieren Sie info@metav-werkzeuge.com oder rufen Sie +49 2822 7131930 an. {"@context":"https://schema.org","@graph":[{"@type":"Product","@id":"#63105-FDA","sku":"63105-FDA","mpn":"63105-FDA","name":"Spiralbohrer 10,5 mm — HSS-G, geschliffen, reduziert 10 mm Schaft, 135°, silber, DIN 338","description":"Geschliffener HSS-G Spiralbohrer, Durchmesser 10,5 mm, Spitzenwinkel 135°, reduzierter Schaft 10 mm, Gesamtlänge 133 mm, Spirallänge 87 mm; geeignet für legierte und unlegierte Stähle sowie Nichteisenmetalle; Norm DIN 338; Einsatz vorrangig an stationären und handgeführten Maschinen bei Verwendung von Kühlschmierstoff empfohlen.","image":["https://files.plytix.com/api/v1.1/file/public_files/pim/assets/57/c3/98/62/6298c3575d155f1bc7e497fd/images/8e/48/c5/69/69c5488eb2b3400ba580741c/logo-metav-1200-675.png","https://files.plytix.com/api/v1.1/file/public_files/pim/assets/57/c3/98/62/6298c3575d155f1bc7e497fd/images/8e/48/c5/69/69c5488eb2b3400ba580741c/logo-metav-1200-675.png","https://files.plytix.com/api/v1.1/file/public_files/pim/assets/57/c3/98/62/6298c3575d155f1bc7e497fd/images/8e/48/c5/69/69c5488eb2b3400ba580741c/logo-metav-1200-675.png"],"additionalProperty":[{"@type":"PropertyValue","name":"Bezeichnung","value":"Spiralbohrer"},{"@type":"PropertyValue","name":"Durchmesser","value":"10,5 mm"},{"@type":"PropertyValue","name":"Spitzenwinkel","value":"135°"},{"@type":"PropertyValue","name":"Ausführung","value":"geschliffen"},{"@type":"PropertyValue","name":"Material","value":"HSS-G"},{"@type":"PropertyValue","name":"Farbe","value":"silber"},{"@type":"PropertyValue","name":"Gesamtlänge","value":"133 mm"},{"@type":"PropertyValue","name":"Spirallänge","value":"87 mm"},{"@type":"PropertyValue","name":"Schaft Ausführung","value":"reduziert 10 mm"},{"@type":"PropertyValue","name":"Norm","value":"DIN 338"},{"@type":"PropertyValue","name":"Modellserie","value":"Standard Line"},{"@type":"PropertyValue","name":"Anwendung","value":"Bohrer für Metall"},{"@type":"PropertyValue","name":"Hersteller","value":"MetavCUT"}]},{"@type":"FAQPage","mainEntity":[{"@type":"Question","name":"Wie eignet sich der Spiralbohrer von MetavCUT für Edelstahl?","acceptedAnswer":{"@type":"Answer","text":"Der Spiralbohrer 10,5 mm von MetavCUT in HSS-G mit 135° Spitzenwinkel ist für härtere Werkstoffe wie Edelstahl geeignet; empfohlen werden Kühlschmierstoff und moderate Vorschubwerte, um Überhitzung und Verschleiß zu reduzieren."}},{"@type":"Question","name":"Kann der Spiralbohrer von MetavCUT in einem 10 mm Bohrfutter verwendet werden?","acceptedAnswer":{"@type":"Answer","text":"Ja, der Spiralbohrer 10,5 mm von MetavCUT verfügt über einen reduzierten Schaft 10 mm, sodass er in Bohrfuttern mit 10 mm Aufnahme gespannt werden kann."}},{"@type":"Question","name":"Ist der geschliffene Spiralbohrer von MetavCUT für Handbohrmaschinen geeignet?","acceptedAnswer":{"@type":"Answer","text":"Der Spiralbohrer 10,5 mm von MetavCUT eignet sich für den Einsatz in handgeführten Akkubohrschraubern im Standard-Bereich; für höchste Präzision und geringeres Bruchrisiko empfiehlt sich jedoch die Nutzung an stationären Maschinen mit ausreichender Kühlung."}},{"@type":"Question","name":"Wo bekomme ich weitere Beratung zur Anwendung des Spiralbohrers von MetavCUT?","acceptedAnswer":{"@type":"Answer","text":"METAV Werkzeuge bietet technische Beratung zur Auswahl und Anwendung des Spiralbohrers 10,5 mm von MetavCUT; kontaktieren Sie info@metav-werkzeuge.com oder rufen Sie +49 2822 7131930 an."}}]},{"@type":"ItemPage","url":"https://metav-shop.de/spiralbohrer-10-5-hss-g-geschliffen-din-338","dateModified":"2026-05-04T12:00:00+01:00","author":{"@type":"Person","name":"Stephan Bayer","url":"https://www.linkedin.com/in/stephan-bayer/"},"publisher":{"@type":"Organization","name":"Metav Werkzeuge GmbH","url":"https://metav-shop.de","logo":{"@type":"ImageObject","url":"https://files.plytix.com/api/v1.1/file/public_files/pim/assets/57/c3/98/62/6298c3575d155f1bc7e497fd/images/8e/48/c5/69/69c5488eb2b3400ba580741c/logo-metav-1200-675.png","width":1200,"height":675},"address":{"@type":"PostalAddress","streetAddress":"Parkring 45","postalCode":"46446","addressLocality":"Emmerich","addressCountry":"DE"},"telephone":"+49 2822 7131930","email":"info@metav-werkzeuge.com"},"about":[{"@type":"Thing","name":"Spiralbohrer"},{"@type":"Thing","name":"HSS-G geschliffen"},{"@type":"Thing","name":"DIN 338"}],"mentions":[{"@type":"Thing","name":"reduzierter Schaft 10 mm"},{"@type":"Thing","name":"Spitzenwinkel 135°"},{"@type":"Thing","name":"Kühlschmierstoff empfohlen"}]}]}

Spiralbohrer (HSS, kurz) Ø 10,1 mm • 118° Spitzenwinkel • Typ N • schwarz • DIN 338 • MetavCUT Der Spiralbohrer ist ein kurzer HSS-Bohrer für präzise Metallbohrungen und eignet sich sowohl für Handbohrmaschine als auch für stationäre Maschinen. HSS-Material für hohe Standzeiten Kurze Ausführung für erhöhte Stabilität Optimiert für Metallbearbeitung nach DIN 338 Typ N Normalspirale für universellen Einsatz 118° Spitzenwinkel für einfaches Anbohren Robuste HSS-Konstruktion für lange Standzeiten und Belastung Die rollgewalzte HSS-Fertigung sorgt für eine erhöhte Elastizität und reduziert das Bruchrisiko insbesondere bei kleineren Durchmessern. Durch die Materialwahl ergibt sich eine hohe Standzeit beim Bohren von legiertem und unlegiertem Stahl, Gusseisen, Nichteisenmetallen sowie Kunststoffen. Anwender profitieren von gleichbleibender Leistung über mehrere Bohrzyklen, was die Wirtschaftlichkeit in Werkstatt und Montage erhöht. Kurze Ausführung für präzise Führung und weniger Vibrationen Die kurze Bauform nach DIN 338 minimiert Auslenkung und ermöglicht bessere Führungsgenauigkeit beim Einspannen. Mit dem Ø 10,1 mm Durchmesser und dem 118° Spitzenwinkel lässt sich das Werkstück sicher anbohren, während die Typ N Normalspirale für zuverlässigen Spantransport bei gängigen Metallarbeiten sorgt. Diese Kombination reduziert Wanderneigung und verbessert die Bohrbildqualität. Geeignete Anwendungen und zielgerichteter Einsatz Für Alltagsaufgaben in Werkstatt, Montage und bei DIY-Projekten ist dieser Bohrertyp ideal geeignet. Die Ausführung richtet sich an Anwender, die mit Handgeräten oder stationären Bohrmaschinen arbeiten und Wert auf Präzision bei mittleren Blech- und Profilstärken legen. Tiefe Sacklochbohrungen oder hochpräzise Passungen erfordern in speziellen Fällen zusätzliche Maßnahmen wie Zentrierung oder Vorbohren. Praktische Hinweise für längere Lebensdauer und sicheres Arbeiten Vorbohren bei dicken Werkstücken und die passende Schnittgeschwindigkeit verlängern die Lebensdauer des Werkzeugs. Die kurze Spiralänge sorgt für bessere Wärmeabfuhr beim Einsatz mit moderater Drehzahl. Bei zäheren Materialien empfiehlt sich reduzierte Vorschubkraft und gegebenenfalls Kühlung, damit Späne nicht festsetzen. Durch richtiges Einspannen und regelmäßige Kontrolle der Spannfutterklemmung bleibt die Betriebssicherheit erhalten. Empfehlung: Für belastbare und präzise Metallbohrungen empfiehlt sich der HSS-Kurzbohrer von MetavCUT als zuverlässiges Werkzeug — bei Fragen zur Anwendung oder Auswahl der passenden Bohrerdimension steht METAV Werkzeuge persönlich zur Beratung per eMail unter info@metav-werkzeuge.com oder telefonisch unter +49 2822 7131930 zur Verfügung Bezeichnung: Spiralbohrer Marke: MetavCUT SKU: 40101-FDA Material: HSS Ausführung: kurz Typ: Typ N Durchmesser: 10,1 mm Gesamtlänge: 133 mm Spiralänge: 87 mm Spitzenwinkel: 118° Farbe: schwarz Für Bohrmaschine: Handbohrmaschine Norm: DIN 338 Hersteller: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ Ist der Spiralbohrer von MetavCUT für Edelstahl geeignet? Der Spiralbohrer von MetavCUT aus HSS eignet sich grundsätzlich für legierten Stahl, wobei bei zähen Edelstählen eine angepasste Schnittgeschwindigkeit und Kühlung empfohlen wird, um Wärmeentwicklung zu reduzieren. Kann ich den HSS-Kurzbohrer mit einer Handbohrmaschine verwenden? Ja, der HSS-Kurzbohrer ist für den Einsatz mit Handbohrmaschine geeignet und bietet durch die kurze Ausführung erhöhte Stabilität und geringere Vibrationen bei standardmäßigen Metallarbeiten. Welche Vorteile bietet die Norm DIN 338 bei diesem Bohrer? Die Einhaltung der DIN 338 garantiert die Kurzbauform und die Zylinderschaftausführung, wodurch eine bessere Führungsgenauigkeit und planbare Einspannlängen bei stationären und mobilen Maschinen erreicht werden. Warum wurde ein Spitzenwinkel von 118° gewählt? Der 118° Spitzenwinkel erleichtert das Anbohren auf gewölbten oder weichen Oberflächen und sorgt für gutes Zentrierverhalten, was bei vielen allgemeinen Metallanwendungen von Vorteil ist. {"@context":"https://schema.org","@graph":[{"@type":"Product","@id":"#40101-FDA","sku":"40101-FDA","mpn":"40101-FDA","name":"Spiralbohrer 40101-FDA","description":"Spiralbohrer HSS, kurz, Ø 10,1 mm, 118° Spitzenwinkel, Typ N, schwarz, DIN 338; Geeignet für Metallbearbeitung mit Handbohrmaschine und stationären Maschinen; Rollgewalzte HSS‑Konstruktion für hohe Standzeit und Stabilität.","image":["https://files.plytix.com/api/v1.1/file/public_files/pim/assets/57/c3/98/62/6298c3575d155f1bc7e497fd/images/8e/48/c5/69/69c5488eb2b3400ba580741b/logo-metav-1200-1200.png","https://files.plytix.com/api/v1.1/file/public_files/pim/assets/57/c3/98/62/6298c3575d155f1bc7e497fd/images/8e/48/c5/69/69c5488eb2b3400ba580741e/logo-metav-1200-900.png","https://files.plytix.com/api/v1.1/file/public_files/pim/assets/57/c3/98/62/6298c3575d155f1bc7e497fd/images/8e/48/c5/69/69c5488eb2b3400ba580741c/logo-metav-1200-675.png"],"additionalProperty":[{"@type":"PropertyValue","name":"Bezeichnung","value":"Spiralbohrer"},{"@type":"PropertyValue","name":"Marke","value":"MetavCUT"},{"@type":"PropertyValue","name":"Material","value":"HSS"},{"@type":"PropertyValue","name":"Ausführung","value":"kurz"},{"@type":"PropertyValue","name":"Typ","value":"Typ N"},{"@type":"PropertyValue","name":"Durchmesser","value":"10,1 mm"},{"@type":"PropertyValue","name":"Gesamtlänge","value":"133 mm"},{"@type":"PropertyValue","name":"Spirallänge","value":"87 mm"},{"@type":"PropertyValue","name":"Spitzenwinkel","value":"118°"},{"@type":"PropertyValue","name":"Farbe","value":"schwarz"},{"@type":"PropertyValue","name":"Für Bohrmaschine","value":"Handbohrmaschine"},{"@type":"PropertyValue","name":"Norm","value":"DIN 338"},{"@type":"PropertyValue","name":"Hersteller","value":"Metav Werkzeuge GmbH"}]},{"@type":"FAQPage","mainEntity":[{"@type":"Question","name":"Ist der Spiralbohrer von MetavCUT für Edelstahl geeignet?","acceptedAnswer":{"@type":"Answer","text":"Der Spiralbohrer von MetavCUT aus HSS eignet sich grundsätzlich für legierten Stahl; bei zähen Edelstählen empfiehlt sich angepasste Schnittgeschwindigkeit und Kühlung, um Wärmeentwicklung zu reduzieren."}},{"@type":"Question","name":"Kann ich den HSS-Kurzbohrer mit einer Handbohrmaschine verwenden?","acceptedAnswer":{"@type":"Answer","text":"Ja, der HSS-Kurzbohrer von MetavCUT ist für den Einsatz mit Handbohrmaschine geeignet und bietet durch die kurze Ausführung erhöhte Stabilität und geringere Vibrationen bei typischen Metallarbeiten."}},{"@type":"Question","name":"Welche Vorteile bietet die Norm DIN 338 bei diesem Bohrer?","acceptedAnswer":{"@type":"Answer","text":"Die Einhaltung der DIN 338 garantiert die Kurzbauform mit Zylinderschaft, was bessere Führungsgenauigkeit und planbare Einspannlängen bei stationären und mobilen Maschinen ermöglicht."}},{"@type":"Question","name":"Warum wurde ein Spitzenwinkel von 118° gewählt?","acceptedAnswer":{"@type":"Answer","text":"Der 118° Spitzenwinkel erleichtert das Anbohren auf gewölbten oder weichen Oberflächen und sorgt für gutes Zentrierverhalten, was viele allgemeine Metallanwendungen verbessert."}}]},{"@type":"ItemPage","url":"https://metav-shop.de/40101-FDA","dateModified":"2026-05-04T12:00:00+01:00","author":{"@type":"Person","name":"Stephan Bayer","url":"https://www.linkedin.com/in/stephan-bayer/"},"publisher":{"@type":"Organization","name":"Metav Werkzeuge GmbH","url":"https://metav-shop.de","logo":{"@type":"ImageObject","url":"https://files.plytix.com/api/v1.1/file/public_files/pim/assets/57/c3/98/62/6298c3575d155f1bc7e497fd/images/8e/48/c5/69/69c5488eb2b3400ba580741c/logo-metav-1200-675.png","width":1200,"height":675},"address":{"@type":"PostalAddress","streetAddress":"Parkring 45","postalCode":"46446","addressLocality":"Emmerich","addressCountry":"DE"},"telephone":"+49 2822 7131930","email":"info@metav-werkzeuge.com"},"about":[{"@type":"Thing","name":"Spiralbohrer HSS kurz"},{"@type":"Thing","name":"Metallbohrung Allgemein"},{"@type":"Thing","name":"DIN 338 Kurzbohrer"}],"mentions":[{"@type":"Thing","name":"Typ N Normalspirale"},{"@type":"Thing","name":"118° Spitzenwinkel"},{"@type":"Thing","name":"Rollgewalztes HSS"}]}]}