High-precision drills for reliable, high-throughput metalworking
Drills provide the fundamental rotating cutting solution for producing accurate cylindrical holes in materials such as structural steel, high-alloy stainless steel, cast iron, non-ferrous metals and engineering plastics, delivering consistent hole quality and extended tool life in CNC machining and turning centres. This category covers everything from classic twist drill made from high-speed steel for general machining to solid carbide drill optimised for high cutting speeds and long run times, offering advanced coatings and internal coolant options for improved heat management. By using optimised point geometries and split points the tools reduce thrust, prevent walking at the start of the cut and ensure superior surface finish, which benefits sectors from general mechanical engineering to automotive component manufacture.
1.60mm Centre Drill DIN 333 Form R 60° HSS Right-Hand, No Countersink - TECWERK
Take advantage of a combination of precise tip geometry, durable HSS construction and a compact 4 mm shank for reliable clamping and repeatable centre holes; ideal for routine workshop use where consistency matters. Order the TECWERK centre drill directly via Metav Werkzeuge or ask our consultants if needed. TECWERK centre drill DIN 333 Form R Ø 1.60 mm (HSS) — 60° countersink The TECWERK centre drill DIN 333 Form R Ø 1.60 mm (HSS) is designed for fast, accurate production of standard centre holes with a radius tip, suitable for general workshop and light industrial applications. HSS construction for durability and wear resistance DIN 333 Form R geometry with radius tip 60° countersink angle for standard centre holes 4 mm shank for secure clamping Reliable seating through radius-tip geometry The radius tip (Form R) follows the requirements of DIN 332 part 1, producing a controlled centre indentation that reduces run-out and facilitates subsequent drilling or turning. The radius-shaped point prevents the brittle fractures sometimes seen with sharp-point centre drills and contributes to consistent workpiece seating, which in turn lowers scrap rates and reduces the need for rework. This geometry is particularly helpful when repeatability and alignment are essential in small-batch production or maintenance tasks. Robust HSS body for everyday machining Constructed from HSS, the tool provides a balance between toughness and hardness that is well suited to general-purpose metalworking. The high-speed steel composition gives resistance to heat and wear during intermittent use, while the right-hand cutting orientation matches common machine spindle directions. A compact 4 mm shank ensures compatibility with small chucks and collets, offering secure clamping for both hand-fed and machine operations. The result is a dependable centre drill that keeps tools and setups consistent across routine processes. Practical machining parameters and compatibility The centre drill is specified as Ø 1.60 mm with an overall length of 35.5 mm and a 60° countersink angle, matching standard centre-hole profiles. It is supplied without protective countersink, so it creates the radius-profile centre only, rather than a stepped pilot. For steel applications up to 800 N, a feed of 0.02 mm/rev is indicated; this recommendation supports efficient material removal while maintaining tip integrity. These clear parameters make process planning straightforward and reduce trial-and-error on the shop floor. Efficiency and workshop integration Compact tooling like this centre drill supports lean workflows: shorter setup times, fewer tool changes and consistent centre positions for downstream operations. The compliance with DIN 333 ensures interchangeability with established procedures and jigs, simplifying procurement and inventory management. Combined with Metav’s availability and advisory support, the bit provides a practical route to improve precision without overcomplicating the tooling portfolio. Contact Metav Werkzeuge for tailored application advice on the TECWERK centre drill and to confirm compatibility with existing holders and processes — Metav Werkzeuge is ready to assist from stock in Emmerich. Technical Data Article number: 2000861950NW Manufacturer: TECWERK Product type: Centre drill (Form R) Standard: DIN 333 Core specifications Diameter: 1.60 mm Overall length: 35.5 mm Shank diameter: 4 mm Countersink angle: 60° Packaging unit: 5 Features and machining notes Material: HSS Cutting direction: right-hand Execution: without protective countersink Application: for centre holes per DIN 332 part 1 Form R (with radius) Recommended feed in steel up to 800 N: 0.02 mm/rev FAQ Is this centre drill suitable for steel work? The TECWERK centre drill DIN 333 Form R in HSS is intended for general steel applications; the recommended feed in steel up to 800 N is 0.02 mm/rev. Can the tool be used in standard holders and chucks? Yes, the 4 mm shank allows secure clamping in chucks and collets that accept that diameter, making the centre drill compatible with many small spindles and bench machines. Why choose the Form R radius tip instead of a sharp point? The radius tip reduces the risk of tip fracture and creates a consistent seat for subsequent drills or centres, improving repeatability and reducing rework. What size of centre hole does the 60° angle produce? The 60° countersink angle produces a standard centre profile in accordance with DIN 332 part 1 Form R, suitable for conventional centre seating and turning operations. Is this a left- or right-hand cutting tool? The drill is right-hand cutting, matching common spindle rotation and standard tool orientations. Manufacturer/Responsible: NORDWEST Handel AG, Robert-Schuman-Straße 17, 44263 Dortmund
1.6mm Centre Drill DIN 333 Form A 60° HSS Right-Hand, Pack of 5 - TECWERK
Take advantage of HSS construction and the standardised geometry of DIN 333 Form A for reliable centring and straight starts; the 60° countersink angle ensures accurate centre holes to DIN 332. Order the centre drill directly via Metav Werkzeuge or ask our consultants if needed. Centre drill DIN 333 Form A Ø1.6 mm HSS, right‑hand — TECWERK The Centre drill DIN 333 Form A Ø1.6 mm HSS, right‑hand is a compact centring tool for precise manufacturing of centre holes and reliable drill starts in general workshop applications. HSS construction for durability DIN 333 Form A standardised geometry 60° countersink angle for precise centring 4 mm shank for secure clamping Accurate starts reduce rework and improve hole quality A standardised centring geometry, compliant with DIN 333 Form A, delivers reproducible results and minimises runout at the beginning of the drilling operation. By providing a clean, centred starting point the tool reduces burr formation and aligns subsequent drills more reliably, which increases first‑pass yield and lowers scrap rates. The combination of hardened design and precise geometry is intended to provide consistent performance on repetitive tasks. Built from HSS for general workshop resilience The tool is manufactured from HSS, offering a balance between toughness and wear resistance for everyday centring operations. The right‑hand cutting direction and compact profile make the tool suitable for standard drilling machines and bench drills. For reference, the recommended feed in steel up to 800 N is 0.02 mm/rev, a figure that supports stable cutting and predictable tool life when machining common ferrous materials. The 4 mm shank diameter ensures secure clamping in compatible collets and small chucks, reducing vibration and promoting concentricity. Designed for standard conformity and efficient replacement Engineered for the production of centre holes according to DIN 332 without a pilot countersink, this centre drill is a practical option for workshops that rely on repeatable standards. The 60° countersink angle is the recognised geometry for effective centring, and the compact format supports confined workspaces and multi‑tool fixtures. Packaged in units of five, the items facilitate quick replenishment and simple inventory management for small to medium workshops that prefer standardised, ready‑to‑use tooling. Choose TECWERK centring tools for dependable workshop performance and order through Metav Werkzeuge — contact Metav Werkzeuge for tailored procurement advice and technical clarification Technical data Article number: 2000861804NW Product type: Centre drill Brand: TECWERK Material: HSS Standard: DIN 333 Form A Facts Nominal diameter: 1.6 mm Shank diameter: 4 mm Countersink angle: 60° Feed in steel up to 800 N: 0.02 mm/rev Packaging unit: 5 pieces Special features For producing centre holes according to DIN 332 without pilot countersink Right‑hand cutting General‑purpose application Complies with DIN 333 Form A geometry FAQ What is this tool best used for? This centre drill is intended for producing precise centre holes and accurate drill starts in accordance with DIN 332, using the DIN 333 Form A geometry for repeatable centring. Which materials can be machined with this centre drill? The TECWERK centre drill, manufactured from HSS, is designed for general‑purpose applications; the specified feed in steel up to 800 N is 0.02 mm/rev for stable cutting. What shank size is required for this tool? A 4 mm shank diameter is specified, so the tool fits collets and chucks dimensioned for a 4 mm shank. Is a pilot countersink required before use? No pilot countersink is required for producing centre holes to DIN 332 when using this centre drill, as it is designed for direct centring without additional protective countersinking. How many pieces are supplied per pack and what is the article number? The packaging unit contains 5 pieces; article number 2000861804NW identifies the TECWERK centre drill. Manufacturer/Responsible: NORDWEST Handel AG, Robert‑Schuman‑Straße 17, 44263 Dortmund
1.6mm Centre Drill DIN 333 Form A 60° Left-Hand HSS, 4mm Shank - TECWERK
Benefit from the combination of HSS construction, DIN 333 Form A geometry and a 60° countersink angle for precise, repeatable centre holes. Order the centre drill directly via Metav Werkzeuge or ask our consultants if needed. Centre drill DIN 333 Form A Ø1.6 mm HSS, left‑hand — TECWERK The centre drill offers standardised geometry for accurate centre holes and is suited to general workshop use where a left‑hand cutting direction is required. HSS construction for toughness and wear resistance DIN 333 Form A standardised geometry 60° countersink angle for precise centre holes Left‑hand cutting, 4 mm shank for standard holders Ensure accurate starts and concentricity with standard geometry A correct centre hole is the foundation of subsequent machining steps. The DIN 333 Form A geometry of this centre drill provides a reliably centred pilot and a defined chamfer thanks to its 60° countersink angle, reducing runout at the outset of drilling or turning. Made from high‑speed steel, the tool combines toughness with edge retention so that starting holes remain accurate over multiple cycles. This reduces rework and contributes to predictable part quality on lathes and drill presses. Durable cutting behaviour for repeatable production The use of HSS material offers a balance between hardness and resistance to shock; this is particularly relevant for small diameters such as Ø1.6 mm, where brittle edges would shorten tool life. The specification includes a recommended feed in steel up to 800 N of 0.02 mm/rev, providing a practical guideline for achieving clean centre holes without overloading the tool. The left‑hand cutting direction is incorporated into the geometry to match specific machine set‑ups or applications that demand reverse rotation. Smooth integration into workshop workflows and tool holders With a 4 mm shank, the centre drill fits common collets and small chucks, making it easy to stock and deploy across multiple workstations. Supplied in a packaging unit of 5, the tool supports orderly inventory rotation and ensures availability for uninterrupted production. Conformity to recognised standards simplifies tool selection and interchangeability, so the centre drill functions as a dependable element in jigs or multi‑tool arrangements and reduces set‑up time during changeovers. For reliable supply and technical guidance on integrating the TECWERK centre drill into production, contact Metav Werkzeuge — practical advice and local stock information are available via info@metav-werkzeuge.com or by phone on +49 2822 7131930 Technical data Article number: 2000861570NW Brand: TECWERK Product type: Centre drill Material: HSS Standard: DIN 333 Facts Nominal diameter: 1.6 mm Shank diameter: 4 mm Countersink angle: 60° Feed in steel up to 800 N: 0.02 mm/rev Packaging unit: 5 Special features DIN 333 Form A geometry Left‑hand cutting For manufacture of centre holes to DIN 332 without protective countersink General purpose use FAQ What is the primary use of this centre drill? The TECWERK centre drill DIN 333 Form A Ø1.6 mm HSS is designed to produce precise centre holes and a defined chamfer as a reliable starting point for subsequent drilling or turning operations. Which materials is the drill suitable for? The TECWERK centre drill is manufactured from HSS for general workshop use; the technical recommendation lists a feed of 0.02 mm/rev in steel up to 800 N as a guideline for safe, effective machining. Why is left‑hand cutting specified for this tool? Left‑hand cutting on the TECWERK centre drill accommodates machine set‑ups or operations requiring reverse rotation and ensures correct chip flow and engagement for those specific processes. Will the shank fit common toolholders? The 4 mm shank of the TECWERK centre drill is compatible with standard small collets and chucks, facilitating quick mounting and consistent concentricity in most workshop holders. How does conformity to DIN 333 and DIN 332 help in production? Standardisation to DIN 333 Form A and reference to DIN 332 mean the TECWERK centre drill provides predictable geometry and interchangeability, reducing set‑up variance and supporting repeatable part quality. Manufacturer / Responsible: NORDWEST Handel AG, Robert‑Schuman‑Straße 17, 44263 Dortmund
1.6mm Centre Drill DIN 333 Form A TiN-Coated HSS 60° Countersink - TECWERK
Take advantage of the combination of durable HSS construction, TiN surface hardening, and standardised geometry for consistent centre-hole quality; this reduces downtime and tool changes while ensuring repeatable results. Order the TECWERK centre drill directly via Metav Werkzeuge or consult our specialists for application advice. Centre drill DIN 333 Form A, 1.6 mm – HSS TiN (TECWERK) The Centre drill DIN 333 Form A 1.6 mm is a TiN-coated HSS centre drill designed for precise preparation of 60° centre holes in general workshop and industrial drilling operations. Centre drill DIN 333 Form A HSS substrate with TiN coating Countersink angle 60° 4 mm shank, right-hand cutting Consistent centre-hole geometry for reliable downstream operations The geometrically defined 60° countersink ensures that the prepared centre holes meet the expectations of conventional turning and drilling workflows, enabling repeatable seating and run-out control. Manufactured to DIN 333 Form A, the tool provides a standardised interface for subsequent steps, which reduces setup time and the need for reworking. The right-hand cutting configuration matches most machine tool spindles and clamping arrangements, promoting smoother chip evacuation and predictable tool behaviour. Longer service life through coating and material selection A HSS substrate combined with a TiN coating delivers a balance between toughness and surface hardness. The hard titanium nitride layer improves wear resistance and reduces built-up edge formation, which extends tool life under typical centre-drilling loads and lowers tooling costs over time. For applications in mixed workshops where tool changes interrupt production, this combination delivers improved longevity without sacrificing edge stability. Easy integration and versatile mounting With a 4 mm shank, the drill integrates with common collets and small chucks used in benchtop and production machinery. The compact nominal diameter of 1.6 mm is suitable for precise centring on small components and pre-drilling operations, while the tool’s compliance with DIN 333 simplifies inventory and replacement planning. The standardised form factor supports rapid tool exchange, limiting machine downtime and fostering a predictable production flow. Practical machining guidance for efficient results For typical steels up to an estimated cutting resistance of 800 N, a recommended feed is approximately 0.02 mm per revolution, which balances cutting forces and surface finish when preparing the centre. The TiN coating lowers friction at the cutting edges, permitting stable operation at commonly used spindle speeds for small-diameter centre drills. When preparing workpieces for turning or drilling, ensuring the workpiece is securely clamped and that coolant or appropriate lubrication is applied will help achieve consistent centring and extend tool life. For dependable centre-drilling performance, select the TECWERK TiN-coated HSS centre drill and contact Metav Werkzeuge for procurement guidance or technical clarification via info@metav-werkzeuge.com or +49 2822 7131930 Technical data SKU: 2000861588NW Product type: Centre drill Brand: TECWERK Facts Nominal diameter: 1.6 mm Shank diameter: 4 mm Countersink angle: 60° Feed in steel up to 800 N: 0.02 mm/rev Cutting direction: Right-hand Packaging unit: 5 Special features HSS material TiN-coated DIN 333 Form A For producing centre holes to DIN 332 without protective countersinking Suitable for general use in workshop operations FAQ What is the recommended feed rate for centre-drilling in steel? For steels with cutting resistance up to roughly 800 N, the recommended feed for this TECWERK centre drill is approximately 0.02 mm per revolution to balance tool life and hole quality. Which shank sizes and clamping systems are compatible? The tool features a 4 mm shank, suitable for standard small chucks and collets used in benchtop machines and production centres where compact centre drills are required. How does the TiN coating affect performance? The TiN coating increases surface hardness and reduces friction at the cutting edges, resulting in improved wear resistance and more stable cutting behaviour during centre-hole preparation. Is this centre drill suitable for precision turning set-ups? Yes, the standardised 60° geometry and conformity with DIN 333 Form A make it suitable for preparing centre holes that provide reliable seating and accurate alignment for turning operations. What size of centre hole does the 1.6 mm nominal diameter produce? The 1.6 mm nominal diameter produces a small, precisely located centre recess appropriate for subsequent drilling or for mounting on centre points in smaller workpieces. Manufacturer / Responsible: NORDWEST Handel AG, Robert-Schuman-Straße 17, 44263 Dortmund
1.6mm HSS Twist Drill DIN 338 ,short, roll forged, black, Type N - MetavCUT
Twist Drill — Type N short HSS drill, 1.6 mm, 118°, black, DIN 338 The Twist Drill Type N is a short High Speed Steel drill designed for precise metal drilling with a 1.6 mm diameter and a 118° point angle, suitable for Drilling Machines and hand drills. Short HSS Twist Drill 1.6 mm diameter 118° point angle for quick centring DIN 338 short design for higher stability Type N normal spiral for metal machining Black finish for corrosion resistance Greater accuracy thanks to short design and high rigidity A short configuration reduces overhang and bending, delivering improved stability and more accurate hole positions when working with metal. The compact geometry of this Twist Drill minimises chatter and allows consistent feeds even when using portable Drilling Machines. Professionals and hobbyists benefit from a compact bit that keeps drill axis deviation low, producing clean holes with minimal rework. Robust HSS material and application guidance for metal Manufactured from HSS (High Speed Steel), this Type N drill combines wear resistance with toughness; the material choice makes the bit suitable for alloyed and unalloyed steel, cast iron, non‑ferrous metals and certain plastics. The 118° point angle offers reliable centring on common metal surfaces and is a practical compromise between cutting aggressiveness and tip life. For best results use steady feed rates and correct cutting fluid when machining harder materials. Who should use this drill and how it stands out This Twist Drill targets workshops, tool rooms and dedicated DIY users who require precision in metalworking. The Type N normal spiral is optimised for metal cutting, providing efficient chip evacuation and predictable performance. The black surface finish improves resistance to corrosion during storage and handling. Choose this short HSS bit when dimensional accuracy and durability matter more than deep-hole capability. We recommend the MetavCUT Twist Drill for reliable metal machining — for technical advice or to confirm suitability contact METAV Werkzeuge: info@metav-werkzeuge.com | Tel: +49 2822 7131930 | WhatsApp: +49 170 2837271 Bezeichnung: Twist Drill Marke: MetavCUT SKU: 40016-FDA Durchmesser: 1.6 mm Spitzenwinkel: 118° Gesamtlänge: 43 mm Spirallänge: 20 mm Ausführung: short Typ: Type N Material: HSS Farbe: black Für Bohrmaschine: Drilling Machine Norm: DIN 338 Anwendung: Drills for metal Hersteller: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What is the MetavCUT Twist Drill mainly used for? The MetavCUT Twist Drill (Type N) is primarily used for machining high‑strength materials and larger-diameter metal holes; its shape is easy to regrind and it withstands higher loads, making it suitable for demanding metalworking tasks. Which three drill types exist? In general the three main drill categories are Metal drills, Wood drills and Stone/Concrete drills; the MetavCUT Twist Drill belongs to the metal drill group and is optimised for cutting metal. Is the MetavCUT Twist Drill suitable for stainless steel? The MetavCUT Twist Drill in HSS can drill stainless steel with correct coolant and reduced feed; however for prolonged work in highly abrasive or very hard stainless grades consider specialised coatings or higher‑alloy variants. How should the MetavCUT Twist Drill be sharpened and maintained? Sharpen the Twist Drill on a bench grinder or dedicated drill sharpener following the original point geometry; maintaining the 118° point and even lips preserves centring and reduces required feed forces.
1.6mm HSS-E Twist Drill DIN 338 ,short, 5% cobalt-alloyed, Type N - MetavCUT
Twist Drill — Type N short, Ø 1.6 mm, 118°, 5% cobalt-alloyed, HSS‑E, DIN 338, Fully Ground (MetavCUT) The Twist Drill Type N short is a precision metal‑drilling tool designed for use in a Drilling Machine, offering a compact overall length and high stability for accurate holes in steel and non‑ferrous metals. Precision short design for stable drilling 1.6 mm Diameter for fine metalwork 118° Tip angle for reliable penetration in softer metals 5% Cobalt‑alloyed HSS‑E for heat resistance and wear life Fully ground shank for high runout accuracy Greater Stability for Accurate Metal Holes The short configuration of this Twist Drill reduces the cantilevered length at the chuck, which results in noticeably lower deflection and improved positional accuracy when drilling. The shorter Spiral Length combined with a compact Overall Length provides a clear benefit for demanding jobs where hole tolerance matters. For workshops using a Drilling Machine, this translates into fewer rejects and less rework, because the tool geometry favours straight, concentric holes even in tougher metals. Heat Resistance and Consistent Cutting Performance Made from HSS‑E with a 5% cobalt alloy, the drill resists softening at elevated temperatures, which preserves cutting edge geometry during prolonged use. The 118° Tip Angle supports efficient cutting in softer steels and reduces walking on curved surfaces, while the Type N Normal Spiral geometry remains the recommended choice for general metal drilling. This material and geometry pairing means longer tool life under intermittent loads and improved chip evacuation in typical metalworking applications. High Precision Finish through Fully Ground Geometry The fully ground flute and geometry, compliant with DIN 338, ensure sharp cutting lips and excellent concentricity. Grinding produces cleaner cutting edges than roll‑forming, which leads to superior hole quality and a better surface finish in the workpiece. Because ground drills can be more brittle than rolled equivalents, it is advisable to use appropriate coolant and moderate feed rates for deep or interrupted cuts to avoid premature tool breakage. Suited Users and Typical Applications This short Type N twist drill is aimed at metalworkers, toolrooms and engineering workshops that require reliable small‑diameter drilling in alloyed and unalloyed steels, cast iron, non‑ferrous metals and plastics. The design is particularly helpful when working on a Drilling Machine where rigidity and repeatable positioning are priorities. For users uncertain about compatibility with specific materials or machine setups, METAV Werkzeuge provides expert consultation to match tooling to application and to recommend optimal machining parameters. Strong recommendation: The MetavCUT Twist Drill short Type N is ideal for precision metalworking—contact METAV Werkzeuge for personalised technical advice via eMail info@metav-werkzeuge.com, phone +49 2822 7131930 or WhatsApp +49 170 2837271 Twist Drill Brand: MetavCUT SKU: 47016-FDA Diameter: 1.6 mm Tip angle: 118° Type: Type N Execution: short Overall length: 43 mm Spiral length: 20 mm Material: HSS‑E (5% cobalt‑alloyed) Shank execution: fully ground Application: Drills for metal / suitable for Drilling Machine Model series: Standard Line Norm: DIN 338 Manufacturer: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ For what is a Twist Drill used? The MetavCUT Twist Drill Type N is primarily applied to the machining of high‑strength materials and larger drill diameters; its short design and material composition make it suitable for demanding metal drilling tasks where stability and precision are required. The geometry is easy to re‑grind and withstands higher loads. Which three drill types exist? Commonly distinguished drill types are Metal Drills (like the MetavCUT Type N Twist Drill), Wood Drills, and Stone/Concrete Drills, each optimised in geometry and material for its respective substrate. Why are Twist Drills sharpened at the tip? The tip sharpening reduces the size of the cross‑cutting edge, which significantly lowers friction and therefore reduces the required feed force. Sharpening also improves centring of the drill tip in the workpiece. Can a metal Twist Drill be used to drill wood? A metal Twist Drill such as the MetavCUT Type N can be used in wood, but guidance and finish are inferior compared with dedicated wood drills. Metal drills are easier to re‑grind and typically exhibit less self‑feeding action in wood.
1.6mm HSS-G Twist Drill DIN 338 ,short, bright finished, Type N - MetavCUT
Dateninkonsistenz festgestellt: Der angegebene Durchmesser 1,6 mm fällt in den Mikro-Bereich (0,05–2,0 mm), für den die Cluster-Empfehlung klar aussagt, dass Bohrer nicht für Handgeführte Maschinen geeignet sind. Gleichzeitig ist im Feld fur_bohrmaschine die Nutzung mit einer Handbohrmaschine angegeben. Aufgrund dieses Widerspruchs kann keine verlässliche und sichere Produktbeschreibung erstellt werden. Bitte prüfen und korrigieren Sie entweder die Angabe zur vorgesehenen Maschine oder bestätigen Sie, dass der Spiralbohrer trotz Mikro-Durchmesser für den Einsatz in Handbohrmaschinen freigegeben ist. Ohne diese Klärung sind Aussagen zur Einsatzempfehlung, zur Standzeit und zur Handhabung nicht zuverlässig ableitbar. SKU 48016-FDA für die Rückmeldung verwenden. Nach Korrektur der Daten wird umgehende Erstellung der vollständigen Produktbeschreibung übernommen.
1.75mm HSS Twist Drill DIN 338 ,short, roll forged, black, Type N - MetavCUT
Twist Drill — Type N short HSS, 1.75 mm diameter, 118° point angle, black, DIN 338 A Twist Drill (Type N) designed for precise metal drilling with a 1.75 mm diameter and a 118° point angle for reliable centring in standard machining applications. Short HSS Type N for precise metal drilling 118° point angle for reliable centring 1.75 mm diameter with 43 mm overall length DIN 338 compliance for standardised quality Black short design for enhanced stability High stability and material benefits for demanding metalwork Constructed from HSS (High Speed Steel), this short Twist Drill offers a robust balance of elasticity and strength that reduces the breakage risk when machining small diameters. The short execution increases stability and minimises deflection during drilling, which results in more consistent hole geometry and longer life under cyclic loads. For customers requiring dependability in series production, the combination of HSS and a short design delivers a reliable solution. Suitable applications and what the geometry achieves The Type N geometry is the classical choice for metalworking: ideal for drilling in alloyed and unalloyed steel, cast iron, non-ferrous metals and plastics. The 118° point angle provides easier penetration and better centring on mildly curved surfaces, which helps reduce wandering at the start of a hole. When paired with appropriate speeds and feeds, this drill suits both stationary drilling machines and hand-operated drilling machines for controlled, repeatable results. Who benefits from this tool and why it was made Engineers, toolroom technicians and maintenance professionals who require precise, stable holes in metal will value the short design and DIN 338 standard compliance. The drill is optimised for situations where rigidity matters more than reach, such as countersunk setups, jig operations or when machining on workpieces with limited overhang. The short flute length simplifies chip evacuation for small diameters, supporting efficiency on the shop floor. Standard conformity and practical guidance for selection Compliant with DIN 338, this short twist drill meets the dimensional and production specifications expected in industrial environments. The designation “short” refers to the reduced overall and spiral length, improving rigidity compared with standard-length drills of the same diameter. For small-diameter holes up to the specified length, this design minimises vibration and produces a cleaner finish, making it suitable for precision tasks in metal fabrication. Strong recommendation: The MetavCUT Twist Drill Type N in HSS is an excellent choice for stable, precise metal drilling — for further technical advice or to confirm suitability for specific applications, contact METAV Werkzeuge: info@metav-werkzeuge.com • +49 2822 7131930 • WhatsApp +49 170 2837271 Designation: Twist Drill Brand: MetavCUT SKU: 400175-FDA Diameter: 1.75 mm Point angle: 118° Type: Type N Colour: black Execution: short Material: HSS Spiral length: 20 mm Overall length: 43 mm Norm: DIN 338 Application: Drills for metal For drilling machine: Drilling Machine Manufacturer: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ For what is a Twist Drill used? The MetavCUT Twist Drill Type N is primarily used for machining high-strength materials and larger drilling diameters in metalworking; its design is easy to regrind and withstands higher loads. Which three drill types exist? Commonly distinguished drill types are metal drills, wood drills and stone/concrete drills; the MetavCUT Twist Drill Type N belongs to the metal drill category. Why are twist drills pointed? The point sharpening reduces the cross-edge at the drill tip; for the MetavCUT Twist Drill Type N this lowers friction, reduces required feed forces and improves centring in the workpiece. Can a Twist Drill be used to drill wood? A metal drill such as the MetavCUT Twist Drill Type N can be used in wood, but it offers less guidance and a less clean finish compared with dedicated wood drills; it is, however, easier to regrind and has a lower self-feeding tendency. For which drilling depths is the Twist Drill most used? A full-diameter through-hole is often performed with a twist drill; for diameters up to around 20 mm and drilling depths up to about 100 mm, the twist drill is the most frequently used tool, applicable to the MetavCUT Twist Drill Type N within its length limits. What is better, HSS or HSSE? The common belief that HSSE steels are universally superior to HSS is not correct; choice should be based on actual working conditions and whether those conditions justify the higher price — the MetavCUT Twist Drill Type N in HSS is suited to many standard metalworking tasks.
1.7mm HSS Twist Drill DIN 338 ,short, roll forged, black, Type N - MetavCUT
Twist Drill — Type N Short HSS, 1.7 mm, 118°, Black, DIN 338 The Twist Drill (Type N) is a short HSS metal drill designed for precision drilling with a 1.7 mm diameter and a 118° tip angle, suitable for use in drilling machines and hand drills. Short design for high stability Precision 1.7 mm diameter for fine holes 118° tip angle for fast centring HSS construction for metalworking durability Conforms to DIN 338 for standardised quality High stability and accuracy for metalworking tasks Thanks to its short design and HSS material, this short twist drill provides increased rigidity and reduced bending during operation, which translates directly into more accurate hole positions. The reduced overhang improves tool life in demanding metalworking environments, making it ideal for setups where concentricity matters. Use in hand drills and drilling machines benefits from the stable geometry to achieve repeatable results with minimal runout. Optimised tip geometry for reliable penetration The 118° tip angle is chosen to balance entry behaviour and centring for common metals; it facilitates reliable penetration and reduces walking on curved or non-flat surfaces. For operators unfamiliar with tip angles: a smaller angle eases initial centring, while larger angles shorten the time to break through harder materials. This Type N geometry is a classic choice for metal, offering dependable starting behaviour without excessive cratering. Material selection and standard conformity for consistent performance Manufactured from HSS (High Speed Steel) and complying with DIN 338, this short twist drill offers a combination of toughness and heat resistance appropriate for alloyed and unalloyed steels, cast iron, non-ferrous metals and plastics. DIN 338 classification ensures consistent dimensions and shank form, simplifying tool selection for machining centres and maintenance workshops that require standardised replacement tools. Practical application and who benefits most Designed primarily for precision metal drilling, the tool suits workshop technicians, toolmakers and maintenance personnel who require fine-diameter holes with reliable centring. The short length reduces flex and is particularly advantageous when drilling up to moderate depths in tough materials, where stability and repeatability are key requirements for production or repair tasks. We recommend the MetavCUT Twist Drill (Type N) for any workshop needing a robust, short HSS solution for precise metal drilling — for personalised advice or additional technical details contact METAV Werkzeuge: info@metav-werkzeuge.com | Tel +49 2822 7131930 | WhatsApp +49 170 2837271 Technical Specifications Bezeichnung: Twist Drill Marke: MetavCUT SKU: 40017-FDA Typ: Type N Durchmesser: 1.7 mm Spitzenwinkel: 118° Gesamtlänge: 43 mm Spirallänge: 20 mm Ausführung: short Material: HSS Norm: DIN 338 Farbe: black Für Bohrmaschine: Drilling Machine Anwendung: Drills for metal Hersteller: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What is the Twist Drill by MetavCUT Type N used for? The Twist Drill from MetavCUT (Type N) is primarily used for drilling high-strength materials and larger diameters in metalworking; its shape makes it easy to resharpen and able to withstand higher loads, which is why it is commonly chosen for demanding applications. Which three drill types exist? The three main drill types are Metal drills, Wood drills and Stone/Concrete drills, and the MetavCUT Twist Drill (Type N) belongs to the category of metal drills optimised for steel and similar materials.
1.7mm HSS-E Twist Drill DIN 338 ,short, 5% cobalt-alloyed, Type N - MetavCUT
Twist Drill (Type N) — short, Ø 1.7 mm, 118°, 5% Cobalt-Alloyed, HSS‑E, DIN 338 — fully ground shank — MetavCUT The Twist Drill (Type N) is a short HSS‑E metalworking drill designed for Drilling Machines, offering enhanced stability and precision for demanding metal‑drilling tasks. Short design for improved stability 5% Cobalt‑alloyed HSS‑E for increased heat resistance DIN 338 compliant for short twist drills Fully ground shank for high concentricity 118° point angle for easier centring in softer metals Short length for maximum stability and precise holes Thanks to its short design, this Twist Drill minimises overhang from the chuck, which significantly reduces bending and vibration during cutting. As a result, the tool achieves better concentricity and an improved surface finish in drilled holes. This makes the drill especially suitable for workshop situations where repeatable, accurate hole geometry is essential, for example in jigs, fixtures and precision metal components. Alloyed HSS‑E chemistry delivers longer tool life under heat Manufactured from HSS‑E with 5% cobalt alloy, the drill combines toughness with superior red‑hardness compared to standard HSS. This material composition increases resistance to softening at elevated cutting temperatures, allowing for higher cutting speeds and extended tool life when machining steels and other metals. The cobalt content also supports easier regrinding, so maintenance and tool refurbishment remain cost‑effective. Geometry and finish optimised for metalworking performance The 118° point angle provides a compromise between entry sharpness and robustness and aids centring on slightly irregular surfaces; it is particularly helpful when working with softer non‑ferrous metals. The fully ground flute and shank geometry ensure sharp cutting edges and high run‑out accuracy, producing clean holes and reducing burr formation. Conforming to DIN 338, this short twist drill is engineered for consistent quality across batches. Intended applications and target users Engineered for Drilling Machines and manual drill presses, this Twist Drill is tailored to professional workshops, toolrooms and maintenance departments that require reliable metal drilling. Typical applications include machining of alloyed and unalloyed steel, cast iron, non‑ferrous metals and technical plastics. The combination of HSS‑E material and short design supports both stationary machine use and demanding hand‑held operations where rigidity and precision are required. Strong recommendation: For precision metalworking choose the MetavCUT Twist Drill Type N with HSS‑E 5% cobalt alloy — for technical questions or tailored advice METAV Werkzeuge provides expert support via eMail: info@metav-werkzeuge.com, Phone: +49 2822 7131930, WhatsApp: +49 170 2837271 Designation: Twist Drill Brand: MetavCUT SKU: 47017-FDA Diameter: 1.7 mm Overall Length: 43 mm Spiral Length: 20 mm Point Angle: 118° Type: Type N Execution: short Material: HSS‑E Alloy/Coating: 5% cobalt‑alloyed Shank Execution: fully ground For: Drilling Machine Application: Drills for metal Model Series: Standard Line Norm: DIN 338 Manufacturer: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What materials is the MetavCUT Twist Drill Type N suitable for? The MetavCUT Twist Drill Type N is suitable for alloyed and unalloyed steels, cast iron, non‑ferrous metals and various plastics; its HSS‑E chemistry with 5% cobalt improves performance on harder or heat‑sensitive cuts and supports higher cutting speeds while maintaining tool life. What is a Twist Drill mainly used for? A Twist Drill such as the MetavCUT Type N is mainly applied when machining high‑strength materials and larger drill diameters; its design is comparatively easy to regrind and can withstand greater mechanical loads, making it a reliable choice for demanding metalworking operations. Which three drill types are there? Common drill types are: Metal drills, Wood drills and Stone/Concrete drills; the MetavCUT Twist Drill Type N belongs to the metal drill category and is optimised for machining metallic materials.
1.8mm HSS Twist Drill DIN 338 ,short, roll forged, black, Type N - MetavCUT
Twist Drill — Type N, 1.8 mm, 118°, Short HSS, Black, DIN 338 (MetavCUT) The Twist Drill Type N is a short HSS metal-drilling bit designed for precise, stable holes in steel and non‑ferrous metals using drilling machines and hand drills. Short design for high stability and precision HSS material for wear-resistant metal drilling 118° tip for improved centring on curved surfaces DIN 338 compliant for standardised quality Suitable for Drilling Machines and Hand Drills Faster, more reliable results thanks to short HSS construction The Twist Drill features a Short overall profile with a Spiral Length of 22 mm and an Overall Length of 46 mm, which reduces overhang and dramatically improves stability during drilling. Made from HSS (High Speed Steel), the bit combines elasticity with wear resistance; this manufacturing method lowers breakage risk for holes below 6 mm and keeps the cutting edge durable under standard metalworking loads. As a result, operators achieve cleaner holes with less vibration and better tool life. Precise centring and controlled penetration for metalworking A 118° Tip Angle gives this Type N geometry reliable centring on slightly curved or irregular surfaces and reduces the tendency to wander at startup. While larger tip angles are used for very hard materials, the 118° geometry is effective for many steels, cast iron and non‑ferrous metals, balancing entry sharpness and cutting life. The normal spiral flute design evacuates chips efficiently, supporting steady feed rates and consistent hole quality. Optimised for workshop use and maintenance tasks Engineers, maintenance technicians and hobbyists benefit from the Type N design: a classic metal‑drilling profile that excels in routine shop and site tasks. Compatibility with standard Drilling Machines and common chucks ensures easy integration into existing toolsets. The compact length makes the bit particularly useful when access is limited or when rigidity is paramount, for instance when drilling in fixtures, jigs or on portable workpieces. Conformity, resharpening and practical handling Conforming to DIN 338, this short Twist Drill follows standardised dimensions and tolerances, making replacement and inventory straightforward. The short geometry also simplifies resharpening: the flute and point shape are easy to regrind while maintaining the original cutting geometry. For best results, clamp the bit securely, use appropriate cutting fluid for ferrous metals and avoid excessive feed to prevent overheating. Proper storage and occasional light resharpening extend service life and maintain hole accuracy. Highly recommended: Choose MetavCUT’s Twist Drill Type N for precise, stable metal drilling — for personalised technical advice METAV Werkzeuge is pleased to assist you at info@metav-werkzeuge.com, Tel +49 2822 7131930 or WhatsApp +49 170 2837271 Designation: Twist Drill Brand: MetavCUT SKU: 40018-FDA Type: Type N Diameter: 1.8 mm Tip angle: 118° Material: HSS Overall length: 46 mm Spiral length: 22 mm Execution: Short Standard: DIN 338 Colour: Black Application: Drills for metal Suitable for: Drilling Machine Manufacturer: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What is the Twist Drill used for? The Twist Drill from MetavCUT, Type N, is primarily used for machining high‑strength materials and larger drill diameters in metalworking. Its shape allows for straightforward resharpening and it endures higher loads, making it suitable for through‑holes and robust workshop applications. Which three drill types are there? Common drill categories are Metal Drill, Wood Drill and Stone/Concrete Drill; the Twist Drill (MetavCUT, Type N) belongs to the Metal Drill group and is optimised for steel and similar materials.
1.8mm HSS-E Twist Drill DIN 338 ,short, 5% cobalt-alloyed, Type N - MetavCUT
Twist Drill — Short Type N Twist Drill, 1.8 mm, 118° Tip, 5% Cobalt‑Alloyed, HSS‑E, DIN 338, Fully Ground Shank by MetavCUT The Twist Drill short Type N is a precision metalworking drill bit designed for use in hand Drilling Machines and stationary equipment for reliable, clean holes in a wide range of metals. Short design reduces deflection and improves precision 5% Cobalt‑alloyed HSS‑E for higher heat resistance 118° Tip for clean entry in softer metals Fully ground shank for high runout accuracy Conforms to DIN 338 for standardized dimensions Greater stability and wear resistance for demanding metalwork The short design of this Twist Drill minimises overhang and therefore reduces the risk of bending during operation, resulting in higher precision in every hole. Manufactured from HSS‑E with 5% cobalt, the bit offers improved heat resistance and longer life when drilling alloys and harder steels. As a Type N Normal Spiral it is particularly well suited to metal applications and follows the dimensional and production guidelines of DIN 338 for consistent performance. Built for accurate alignment and clean hole starts A fully ground shank ensures excellent concentricity and low runout in both hand and bench Drilling Machines, improving hole quality and tool life. The 118° tip angle facilitates a clean entry, especially in softer materials such as aluminium, while the short overall geometry (Total Length 46 mm, Spiral Length 22 mm) increases stiffness. This combination yields precise centring and a controlled cutting action that benefits workshop professionals and maintenance technicians alike. Practical advantages, recommended uses and handling This Twist Drill is ideal for professional metalworkers, maintenance crews and precision hobbyists who need reliable results in alloys, Cast Iron, non‑ferrous metals and plastics. The roll‑or‑grind manufacturing choices mean the ground version delivers sharper cutting edges and better roundness, though it benefits from appropriate cooling to reduce the risk of breakage. For drilling below 6 mm diameter, the low‑temperature treatment used in production increases elasticity and reduces fracture risk, making the bit a smart choice for repeated, precise metal drilling tasks. MetavCUT’s short Twist Drill is recommended for precision metal drilling — for expert technical advice and application support contact METAV Werkzeuge: info@metav-werkzeuge.com | Tel: +49 2822 7131930 | WhatsApp: +49 170 2837271 Designation: Twist Drill (Short Type N) Brand: MetavCUT SKU: 47018-FDA Diameter: 1.8 mm Tip Angle: 118° Material: HSS‑E (High Speed Steel, Cobalt alloyed) Alloy/Coating: 5% cobalt‑alloyed Type: Type N (Normal Spiral) Execution: Short Overall Length: 46 mm Spiral Length: 22 mm Shank Finish: Fully ground Application: Drills for metal / suitable for Hand Drilling Machine and stationary machines Standard/Norm: DIN 338 Model Series: Standard Line Manufacturer: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What is the Twist Drill used for? The MetavCUT Twist Drill (Type N) is mainly applied to machining high‑strength materials and larger drill diameters; its design is easy to regrind and endures higher loads, which makes it suitable for demanding metalworking tasks. Which three drill types exist? The common drill categories are Metal drill, Wood drill and Stone/Concrete drill, with the MetavCUT Twist Drill belonging to the Metal drill category appropriate for ferrous and non‑ferrous metals.
1.9mm HSS Twist Drill DIN 338 ,short, roll forged, black, Type N - MetavCUT
Kombinieren Sie die hohe Stabilität durch die kurze Ausführung mit der Verschleißfestigkeit des HSS-Materials und dem präzisen Spitzenwinkel 118° für saubere Metallbohrungen. Bestellen Sie den Spiralbohrer von MetavCUT direkt über Metav Werkzeuge oder nutzen Sie unsere technische Beratung bei Bedarf. Spiralbohrer – HSS kurz, Typ N von MetavCUT Der Spiralbohrer ist ein kurzer HSS-Metallbohrer nach DIN 338, entwickelt für präzise Bohrungen in legierten und unlegierten Stählen sowie in Nichteisenmetallen. Kurze Ausführung für erhöhte Stabilität Rollgewalztes HSS für geringeres Bruchrisiko Spitzenwinkel 118° für einfaches Anbohren Geeignet für präzise Metallbearbeitung Zylinderschaft kompatibel mit Handbohrmaschine Präzision und Stabilität bei feinen Metallbohrungen Die kurze Bauart reduziert die Auskraglänge und minimiert das Verbiegen bei feinen Bohrungen. Durch die geringere Hebelwirkung bleibt die Bohrung stabil und das Bohrbild sauber, was insbesondere bei Durchmessern im Mikro-Bereich entscheidend ist. Das Resultat sind exakte Bohrungen mit reduziertem Nacharbeitaufwand und konstanter Lochqualität. HSS-Material: Warum Schnellarbeitsstahl für kleine Bohrdurchmesser wichtig ist Das verwendete HSS (Schnellarbeitsstahl) ist rollgewalzt gefertigt und bietet Elastizität sowie erhöhte Zähigkeit. Bei Durchmessern unter 6 mm verringert sich dadurch das Bruchrisiko gegenüber geschliffenen Ausführungen. Kunden profitieren von einer längeren Standzeit und zuverlässigen Ergebnissen beim Bohren in Stahl, Gusseisen und Kunststoffen. Praktische Anwendung und Hinweise für sicheres Arbeiten Für feine Bohrungen empfiehlt sich ein zentriertes Anpunkten vor dem Bohren und eine ruhige, gleichmäßige Vorschubgeschwindigkeit. Bei Handbohrmaschine ist eine stabile Führung und niedriger Vorschub wichtig, um Verkantung zu vermeiden. Kühlung und Spanabfuhr verbessern die Standzeit bei längeren Einsätzen; bei sehr filigranen Arbeiten ist eine stationäre Aufnahme vorteilhaft. Für wen dieser Bohrer besonders geeignet ist Der Bohrer richtet sich an Anwender, die präzise Metallbearbeitung verlangen: Feinmechanik, Prototypenbau, Modellbau und Werkstätten mit hohen Qualitätsanforderungen. Die Kombination aus DIN 338-Konformität, Typ N-Spiralgeometrie und der kurzen Ausführung macht das Werkzeug zur verlässlichen Wahl für detailorientierte Bearbeitungen. Mit dem HSS-Spiralbohrer von MetavCUT setzen Sie auf Präzision und Stabilität – bei Fragen erreicht Sie Metav Werkzeuge per eMail info@metav-werkzeuge.com oder telefonisch unter +49 2822 7131930 Produktmerkmale Artikelnummer: 40019-FDA Marke: MetavCUT Bezeichnung: Spiralbohrer Material: HSS Norm: DIN 338 Typ: Typ N Farbe: schwarz Ausführung: kurz Für Bohrmaschine: Handbohrmaschine Verpackungseinheit: 10 Fakten Durchmesser: 1,9 mm Gesamtlänge: 46 mm Spirallänge: 22 mm Spitzenwinkel: 118° Verpackungseinheit: 10 Besonderheiten DIN 338: Norm für kurze Spiralbohrer HSS: Schnellarbeitsstahl, erhöht Zähigkeit und Standzeit Typ N: Normalspirale, klassisch für Metall Zylinderschaft: kompatibel mit Standardspannfuttern FAQ Für welche Materialien ist der Bohrer geeignet? Der Spiralbohrer von MetavCUT (Typ N, SKU 40019-FDA) eignet sich für legierten und unlegierten Stahl, Gusseisen, Nichteisenmetalle und Kunststoffe; bei harten Werkstoffen empfiehlt sich angepasste Schnittgeschwindigkeit und Kühlung. Ist die kurze Ausführung für Handbohrmaschinen geeignet? Die kurze Ausführung verbessert die Stabilität; bei Einsatz mit Handbohrmaschine ist auf exakte Führung, ruhigen Vorschub und Anpunkten zu achten, um Verkantung zu vermeiden. Welchen Spitzenwinkel hat der Bohrer und was bedeutet das praktisch? Der Bohrer hat einen Spitzenwinkel von 118°, was das Anbohren erleichtert und sich besonders bei weicheren Metallen und dünnen Blechen bewährt. Wie viele Bohrer sind in einer Verpackungseinheit? Die Verpackungseinheit umfasst 10 Stück, geliefert vom Hersteller MetavCUT; die SKU lautet 40019-FDA.
1.9mm HSS-E Twist Drill DIN 338 ,short, 5% cobalt-alloyed, Type N - MetavCUT
Twist Drill — Type N, 1.9 mm, 118°, 5% cobalt-alloyed, short, HSS‑E, DIN 338 The Twist Drill Type N is a short HSS‑E metal drilling bit designed for precise work in steels and non‑ferrous metals with a 118° point angle for controlled penetration. Short design for high stability and accuracy 5% cobalt‑alloyed HSS‑E for extended life Fully ground shaft for superior concentricity Conforms to DIN 338 for short twist drills Ideal for Drilling Machine applications Durable alloy and longer lifetime for metalworking The short HSS‑E cutting tool combines a 5% cobalt‑alloyed composition with a roll‑formed and ground geometry to deliver increased heat resistance and wear life when machining Steel and Cast Iron. Because the metal matrix contains additional cobalt, the bit retains hardness at elevated Temperatures, which reduces flank wear during extended Drilling operations. This construction translates into fewer tool changes and more consistent hole quality for workshop and production environments. Short length for superior stability and precise holes A reduced overall length means less overhang from the chuck and therefore significantly improved Stability and concentricity under load. The shorter cantilever minimizes vibration and the risk of deviation, so each hole is truer and cleaner. For applications where accuracy matters—jigs, fixture work and thin‑section components—the compact format ensures safer handling and lower breakage risk compared with longer equivalents. Geometry tuned for metal and controlled entry The 118° point angle and classic Type N spiral make this Short Twist Drill particularly suitable for general Metalworking, enabling controlled entry and good centring on flat surfaces. The fully ground flute geometry produces sharp cutting lips and a precise chisel edge, yielding clean holes with reduced burr. For tasks in alloyed and unalloyed Steel, non‑ferrous Metals and Plastics, this design balances penetration and tool life. Practical handling and maintenance advice To maximise service life, use moderated cutting speeds and adequate coolant when drilling hard or heat‑sensitive Materials. The fully ground shaft offers excellent run‑out characteristics in collets and chucks, but requires proper clamping to avoid slippage. When resharpening is necessary, observe the original point angle and maintain flute geometry to preserve Performance. For bench and machine use, the shorter length reduces bending stresses and simplifies chip evacuation. Choose the MetavCUT short Twist Drill for demanding metal applications — METAV Werkzeuge provides expert advice and technical support via eMail: info@metav-werkzeuge.com, Phone: +49 2822 7131930 and WhatsApp: +49 170 2837271 Designation: Twist Drill (Short) Brand: MetavCUT SKU: 47019-FDA Diameter: 1.9 mm Total length: 46 mm Spiral length: 22 mm Point angle: 118° Type: Type N Execution: short Colour: 5% cobalt-alloyed Shaft finish: fully ground Material: HSS-E Standard: DIN 338 For drilling machine: Drilling Machine Application: Drills for metal Model series: Standard Line Packaging unit: 10 Manufacturer: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What is the main use of this Twist Drill from MetavCUT Type N? The MetavCUT Twist Drill Type N is primarily used for machining high‑strength materials and larger drill diameters in Metalworking. Its short design improves stability and precision, and the 5% cobalt content helps the bit withstand higher Temperatures and mechanical stress during demanding drilling tasks. Which three drill types are commonly distinguished? Common drill categories are Metal drill (such as the MetavCUT Twist Drill Type N), Wood drill, and Stone/Concrete drill. Each is optimised for its material class and must be selected according to the workpiece to ensure proper hole quality and tool life. Why are Twist Drills sharpened at the tip? Sharpening the tip reduces the cross‑cutting edge area at the Twist Drill point, lowering friction. By reducing Reibkräfte, less thrust is required during drilling and the bit centres more reliably in the workpiece. Can a metal drill be used to drill wood? A Metal drill like the MetavCUT Twist Drill can be used in Wood, but guidance and surface finish are generally inferior compared with dedicated Wood drills. Metal drills are easier to resharpen and tend to produce less self‑feed, so careful feed control is recommended.
1.9mm HSS-G Twist Drill DIN 338 ,short, bright finished, Type N - MetavCUT
Twist Drill — Short HSS‑G Metal Drill, 1.9 mm, 118° Tip, Type N, Bright Finished, Short Execution, DIN 338 The Twist Drill is a short HSS‑G Type N metal drill designed for precise drilling in metal on a Drilling Machine and suitable for demanding workshop and industrial applications. Short HSS‑G design for higher stability 1.9 mm diameter for fine, precise holes 118° tip angle for reliable centering in metals Fully ground shank for high concentricity Conforms to DIN 338 for short twist drills Durable Material for Consistent Results and Longer Tool Life Made from HSS‑G, this short Twist Drill delivers high hardness and sharp cutting edges that produce clean holes in Metal. The ground flute geometry ensures excellent chip evacuation and reduces friction, which benefits tool life. Because the drill is manufactured with a CNC grinding process rather than roll forming, users gain high Rundlaufgenauigkeit and precise hole quality, especially important when working with alloys or cast materials. Short Design That Improves Stability and Precision at the Cut A shorter overall length reduces overhang and increases stability during drilling, which decreases the tendency to wander or bend under load. The short execution is particularly advantageous when drilling in hard Materials such as Steel, Cast Iron and Tempered Alloys, providing better concentricity and less vibration. This design therefore enables more consistent hole diameters and improved surface finish even under higher cutting forces. Geometry and Cutting Behaviour Optimised for Metalworking The 118° tip angle and Type N spiral geometry represent the classic metalworking configuration, supporting good centering and controlled chip formation. The sharpened tip reduces quench forces at initial contact and helps avoid skidding on curved surfaces. The fully ground shank and flute profile facilitate accurate clamping and runout behaviour, which is essential for demanding assembly or precision manufacturing tasks. Who Benefits and How to Use This Tool Effectively Designed for machinists and metalworkers, the Profi Line Twist Drill from MetavCUT is ideal for tasks requiring fine diameters and repeatable accuracy. Use on fixed or portable Drilling Machines with appropriate coolant for long tool life; the shorter geometry suits tight setups or jig work. For less experienced users, coolant and moderate spindle speeds are recommended to reduce heat and prolong cutting edge life. Highly recommended: choose the MetavCUT Profi Line Twist Drill for precision metal drilling and contact METAV Werkzeuge for expert advice and technical support — eMail: info@metav-werkzeuge.com • Phone: +49 2822 7131930 • WhatsApp: +49 170 2837271 Technical information Designation: Twist Drill Brand/Manufacturer: MetavCUT SKU: 48019-FDA Diameter: 1.9 mm Tip angle: 118° Type: Type N (Normal Spiral) Colour: Bright finished Execution: Short Material: HSS-G (Ground) Standard: DIN 338 Overall length: 49 mm Spiral length: 24 mm Shank finish: Fully ground Suitable for: Drilling Machine / Hand Drills for Metal applications Series: Profi Line Manufacturer: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ Can the MetavCUT Twist Drill be used in a hand drill as well as a drilling machine? The MetavCUT Twist Drill (Type N, HSS‑G) is primarily optimised for use on a Drilling Machine to ensure low runout and consistent cooling, but it can also be used in a Hand Drill if the chuck provides secure clamping and the correct speeds and coolant are applied to avoid overheating. Is the MetavCUT Twist Drill suitable for drilling alloyed steels? Yes, the MetavCUT Twist Drill from the Profi Line is suitable for alloyed and unalloyed Steel, Cast Iron and other Metals; its ground HSS‑G geometry gives sharp cutting edges that perform well in such Materials when used with appropriate feeds and coolant. What are Twist Drills used for? Twist Drills are mainly used for machining high‑strength Materials and larger hole diameters; this form is easy to regrind and withstands higher loads, making it suitable for demanding applications in Metalworking. Which three drill types exist? The main drill types are Metal Drills, Wood Drills and Masonry/Concrete Drills.
10,2mm Spiralbohrer, geschliffen, HSS‑G, 135° Spitzenwinkel, reduziert 10mm Schaft - MetavCUT
Der geschliffene Spiralbohrer verbindet höchste Präzision durch HSS-G Geometrie, einen reduzierten Schaft 10 mm für flexible Spannbarkeit und den 135° Spitzenwinkel für harte Werkstoffe; so erzielen Sie schnelleres Bohren und geringeren Anpressdruck bei Metallbearbeitung. Bestellen Sie den Spiralbohrer 10,2 mm von MetavCUT direkt über Metav Werkzeuge oder fragen Sie unsere Beratung bei Bedarf an. Spiralbohrer 10,2 mm — MetavCUT Standard Line Der Spiralbohrer 10,2 mm ist ein geschliffener HSS-G Bohrer zur präzisen Metallbearbeitung auf stationären Werkzeugmaschinen 10,2 mm präziser Spiralbohrer HSS-G geschliffen für Metallbearbeitung Reduzierter Schaft 10 mm für kleine Bohrfutter Spitzenwinkel 135° für harte Werkstoffe DIN 338 kurze Spiralbohrer Norm Höchste Präzision dank geschliffener HSS-G Geometrie Die geschliffene HSS-G Oberfläche sorgt für sehr scharfe Schneiden und ausgezeichnete Rundlaufgenauigkeit, was besonders bei Metallbohrungen messbare Vorteile bringt. Durch den CNC-Schliff entstehen saubere Bohrlöcher mit reduziertem Ausriss, sodass nachfolgende Arbeitsschritte einfacher und schneller ausfallen. Diese Verarbeitung macht den Bohrer ideal für legierten und unlegierten Stahl sowie Gusseisen. Effizienzsteigerung und Bedienkomfort bei Bohrvorgängen Die Konstruktion reduziert die notwendige Anpresskraft und erhöht die Vorschubgeschwindigkeit, sodass der Arbeitszyklus effizienter wird. Der Spiralbohrer 10,2 mm ermöglicht ein bis zu 40 % schnelleres Bohren und benötigt dabei deutlich weniger Kraftaufwand als herkömmliche HSS-Ausführungen. Weniger Kraftbedarf bedeutet weniger Belastung für Maschine und Bediener sowie geringeren Verschleiß der Spannmittel. Praktische Hinweise zur Anwendung und Werkstoffeignung Mit dem 135° Spitzenwinkel dringt der Bohrer zügig in harte Werkstoffe ein und eignet sich daher besonders für Edelstahl und tempergehärtete Materialien. Die Spirallänge von 87 mm ermöglicht kontrollierte Späneabfuhr bei mittleren Bochtiefen; bei sehr tiefen Löchern empfiehlt sich stufenweises Aufbohren. Für stationäre Bohrmaschinen und den Einsatz mit Kühlschmierstoff wird die beste Standzeit erreicht. Passgenauigkeit und Einsatzszenarien in der Werkstatt Der reduzierte Schaft 10 mm erlaubt das Spannen größerer Bohrdurchmesser in Bohrfuttern mit begrenzter Spannweite und erhöht so die Flexibilität in der Werkstatt. Dieses Werkzeug richtet sich an Metallbearbeiter, Instandhalter und industrielle Anwender, die auf zuverlässige Normware nach DIN 338 setzen. Durch die robuste Ausführung eignet sich der Bohrer vor allem für stationäre Maschinen in Serien- und Einzelteilfertigung. Empfehlung: Den geschliffenen HSS-G Spiralbohrer von MetavCUT in 10,2 mm direkt bei Metav Werkzeuge anfragen — per E‑Mail info@metav-werkzeuge.com oder Telefon +49 2822 7131930 Produktmerkmale Artikelnummer: 63102-FDA Marke: MetavCUT Bezeichnung: Spiralbohrer Modellserie: Standard Line Daten Durchmesser: 10,2 mm Gesamtlänge: 133 mm Spirallänge: 87 mm Spitzenwinkel: 135° Verpackungseinheit: 1 Besonderheiten Ausführung: geschliffen Material: HSS-G (geschliffener Schnellarbeitsstahl) Schaftausführung: reduziert 10 mm Farbe: silber Anwendung: Bohrer für Metall Norm: DIN 338 (kurze Spiralbohrer mit Zylinderschaft) FAQ Ist der Spiralbohrer für Handgeführte Akkubohrschrauber geeignet? Der geschliffene Spiralbohrer 10,2 mm von MetavCUT ist primär für stationäre Maschinen konzipiert; aufgrund der feineren Schneide kann er bei Handmaschinen schneller brechen, daher wird der Einsatz an stationären Bohrmaschinen empfohlen. Welche Werkstoffe lassen sich mit diesem Bohrer bearbeiten? Der HSS-G Spiralbohrer eignet sich für legierten und unlegierten Stahl, Gussstahl, Gusseisen, Sintereisen, Temperguss sowie Nichteisenmetalle und Hartkunststoff. Warum ist der Spitzenwinkel 135° wichtig? Der 135° Spitzenwinkel reduziert das Anlaufen beim Anbohren in harte Werkstoffe und verbessert die Zentrierung, wodurch der Bohrer leichter in Edelstahl und gehärteten Materialien arbeitet. Was bedeutet „reduzierter Schaft 10 mm“ und wozu ist das gut? Ein reduzierter Schaft 10 mm bedeutet, dass der hintere Schaft auf 10 mm abgedreht ist, um größere Bohrdurchmesser in Bohrfuttern mit begrenzter Spannweite verwenden zu können; das erhöht die Kompatibilität mit kleineren Spannfuttern. Entspricht der Bohrer einer Norm und was heißt das für die Auswahl? Ja, der Bohrer entspricht DIN 338, was die Abmessungen und Toleranzen für kurze Spiralbohrer mit Zylinderschaft festlegt; das erleichtert die Auswahl passender Ersatzwerkzeuge und Spannmittel. Enthält die Verpackung nur einen Bohrer? Die Verpackungseinheit beträgt 1, somit wird der Spiralbohrer 10,2 mm einzeln geliefert und ist unter der Artikelnummer 63102-FDA gelistet.
10,5mm Rollgewalzter Spiralbohrer, HSS, 118° Spitzenwinkel, reduziert 10mm Schaft, schwarz - MetavCUT
Spiralbohrer MetavCUT Standard Line (Typ N, HSS) Der Spiralbohrer wurde für das präzise Durchbohren von Metall an stationären und handgeführten Maschinen konzipiert und bietet eine ausgewogene Kombination aus Bruchsicherheit und Wirtschaftlichkeit. MetavCUT Standard Line Spiralbohrer Typ N Rollgewalzte HSS-Ausführung für brucharme Einsätze Reduzierter Schaft 10 mm für kleinere Bohrfutter DIN 338 konform für kurze Spiralbohrer Spitzenwinkel 118° für sichere Zentrierung Zuverlässige Leistung für den Werkstattalltag Der Kurzspiralbohrer aus der Standard Line verbindet HSS-Härte mit der zähen Eigenschaft der rollgewalzten Fertigung. Das Ergebnis ist ein Bohrer, der beim Durchbohren von legiertem und unlegiertem Stahl, Gusseisen sowie Nichteisenmetallen weniger zum Sprödbruch neigt. Anwender profitieren von reduzierten Maschinenstillständen und geringeren Nachbestellungen, weil Bruchausfälle seltener auftreten. Gleichzeitig bleibt die Fertigungskostenvorteile erhalten, sodass ein gutes Kosten-Nutzen-Verhältnis erreicht wird. Herstellverfahren erklärt und Praxisvorteile Beim rollgewalzten Verfahren wird der Rundstab erhitzt und in Spiralform gewalzt, statt aus dem Vollen geschliffen zu werden. Dadurch entsteht eine höhere Elastizität des Werkstoffs, was insbesondere bei Durchmessern unter 6 mm das Bruchrisiko senkt; bei 10,5 mm führt das Verfahren zu robuster Standzeit für den Alltagsgebrauch. Die DIN 338 normiert diese kurzen Spiralbohrer mit Zylinderschaft und stellt sicher, dass Abmessungen und Aufnahme kompatibel zu gängigen Bohrfuttern sind. Für Anwender bedeutet das: zuverlässige Einsetzbarkeit bei Standardbohrungen in Metall ohne teure Spezialwerkzeuge. Einsatzbereiche, Zielgruppe und Anwendungsszenarien Dieser Bohrer ist ausgelegt für Werkstätten, Montagebetriebe, Instandhaltung und ambitionierte Heimwerker, die regelmäßig Metall bearbeiten. In der Praxis eignet sich das Werkzeug für das Bohren in Blechen, Profilen und flachen Stahlkomponenten sowie in Aluminium und Kunststoffen. Aufgrund des reduziert 10mm Schaftes passt der Bohrer auch in Bohrfutter, die nur bis 10 mm spannen, was die Flexibilität auf der Werkbank erhöht. Wer robuste, kosteneffiziente Bohrungen ohne übermäßige Präzisionsanforderungen benötigt, findet hier eine pragmatische Lösung. Sichere Anwendung und Materialhinweise Für saubere Ergebnisse empfiehlt sich vor dem Bohren ein Anpunkten mit einem Zentrierbohrer, besonders bei höheren Oberflächenrauheiten. Bei legierten Stählen erhöht eine leichte Kühlschmierstoffzufuhr die Standzeit. Der Spitzenwinkel 118° unterstützt das schnelle Eindringen und die einfache Zentrierung auf ebenen Flächen; für sehr weiche Materialien oder gewölbte Oberflächen kann ein anderer Winkel vorteilhaft sein. Der Bohrer ist nicht für extrem hohe Präzision in Feinpassungen ausgelegt, dort sind geschliffene Werkzeuge sinnvoller. Mit dem Spiralbohrer von MetavCUT Standard Line empfehlen wir den Einsatz für wirtschaftliche Metallbohrungen; Bestell- und Beratungsanfragen gerne an info@metav-werkzeuge.com oder telefonisch +49 2822 7131930 und WhatsApp +49 170 2837271. Produkteigenschaften Artikelnummer: 61105-FDA Marke: MetavCUT Bezeichnung: Spiralbohrer Modellserie: Standard Line Norm: DIN 338 Fakten Durchmesser: 10,5 mm Gesamtlänge: 133 mm Spirallänge: 87 mm Spitzenwinkel: 118° Verpackungseinheit: 5 Besonderheiten Ausführung: rollgewalzt Material: HSS Farbe: schwarz Schaftausführung: reduziert 10mm Typ: Typ N FAQ Ist dieser Bohrer für gehärteten Stahl geeignet? Der MetavCUT Spiralbohrer Standard Line (Typ N, SKU 61105-FDA) ist primär für legierte und unlegierte Stähle sowie Gusseisen und Nichteisenmetalle ausgelegt; für sehr harte, gehärtete Stähle sind spezialisierte Vollhartmetallwerkzeuge empfehlenswert. Kann der Bohrer in einem Akkubohrschrauber verwendet werden? Ja, der Spiralbohrer MetavCUT Standard Line lässt sich bei typischen Heimwerker- und Werkstattakkuschraubern einsetzen, insbesondere dank des reduziert 10mm Schaftes, der auch in begrenzte Bohrfutter passt. Wie beeinflusst die rollgewalzte Fertigung die Standzeit? Die rollgewalzte Ausführung erhöht die Zähigkeit des HSS-Materials, wodurch der Bohrer tendenziell bruchsicherer ist und im Alltagsgebrauch eine stabile Standzeit bietet; extreme Präzisionsanforderungen können jedoch besser von geschliffenen Bohrern erfüllt werden. Welchen Spitzenwinkel hat der Bohrer und was bedeutet das? Der Bohrer verfügt über einen Spitzenwinkel von 118°, was eine gute Zentrierfähigkeit und Eindringwirkung bei metallischen Werkstoffen gewährleistet und das Anbohren besonders auf ebenen Flächen erleichtert. Entspricht der Bohrer einer Norm und was sagt das aus? Ja, der Spiralbohrer MetavCUT Standard Line erfüllt die DIN 338, die kurze Spiralbohrer mit Zylinderschaft klassifiziert und damit Kompatibilität und Standardabmessungen für den Einsatz an gängigen Maschinen sicherstellt.
10,5mm Spiralbohrer, 118° Spitzenwinkel, HSS, rollgewalzt, Morsekegel, 87mm Spiralänge - MetavCUT
Kombinieren Sie die Wirtschaftlichkeit des rollgewalzten Herstellverfahrens mit der Widerstandsfähigkeit von HSS und der sicheren Spannaufnahme durch den Morsekegel für zuverlässige Metallbohrungen; bestellen Sie den Spiralbohrer direkt über Metav oder kontaktieren Sie unsere Beratung bei technischen Fragen. Spiralbohrer von MetavCUT – HSS, Morsekegel Der Spiralbohrer von MetavCUT ist ein rollgewalzter HSS-Bohrer für präzise Metallbohrungen in Werkstatt und Industrie. HSS-Material für hohe Zähigkeit und Standzeit Morsekegelschaft für sichere Aufnahme in Säulenbohrmaschinen Rollgewalzte Fertigung reduziert Bruchrisiko bei kleinen Durchmessern DIN 345 Norm für universelle Einsetzbarkeit Spirallänge 87 mm für sauberen Spantransport Höhere Zähigkeit durch rollgewalzte Fertigung Die rollgewalzte Herstellungsweise macht den Bohrer besonders zäh und bruchsicher, ohne die Wirtschaftlichkeit zu opfern. Durch das Walzen entsteht eine elastischere Spanstruktur, die vor allem bei kleineren Bohrdurchmessern das Bruchrisiko vermindert. Für Anwender bedeutet das weniger Ausschuss und längere Betriebsintervalle, wenn HSS-Werkzeuge in wechselnden Metallwerkstoffen eingesetzt werden. Passende Maschinen und typische Anwendungen Dieser Bohrer gehört in den Standard-Bereich und eignet sich für allgemeine Werkstattaufgaben sowie stationäre Bohrungen in Stahl, Gusseisen und Nichteisenmetallen. Die Morsekegelschaft macht ihn ideal für Säulenbohrmaschinen, Drehmaschinen mit MK-Aufnahme und industrielle Ständerbohrmaschinen, bei denen ein sicherer Sitz und hohe Drehmomentübertragung gefordert sind. Dadurch werden präzise Bohrbilder und reproduzierbare Ergebnisse ermöglicht. Einfaches Handling und praktische Vorteile Der Spitzenwinkel von 118° sorgt für leichtes Eindringen in weichere Werkstoffe und erleichtert das Zentrieren auf gewölbten Oberflächen. Die Spirallänge 87 mm unterstützt den effektiven Spantransport, was besonders bei tiefen oder längeren Bohrungen die Standzeit erhöht. Insgesamt reduziert sich der Arbeitsaufwand, weil Nacharbeiten seltener nötig sind und die Bohrung zügig erstellt werden kann. Materialempfehlungen und Einsatzbedingungen Der Bohrer ist für legierten und unlegierten Stahl, Grauguss, Temperguss, Sphäroguss sowie Neusilber und Kunststoffe ausgelegt. Bei Anwendungen in zähen Werkstoffen empfiehlt sich eine angepasste Kühlung und das Vorbohren nach den üblichen Richtlinien. Mit DIN 345 als Normreferenz sind Ersatzteile und Maschinenschnittstellen leicht identifizierbar, was die Integration in bestehende Arbeitsprozesse vereinfacht. Wählen Sie den MetavCUT Standard Line Spiralbohrer mit Morsekegelschaft für robuste und wirtschaftliche Metallbohrungen; bei offenen Fragen erreichen Sie unsere Techniker per E‑Mail unter info@metav-werkzeuge.com oder telefonisch unter +49 2822 7131930 Produktmerkmale Artikelnummer: 54105-FDA Marke: MetavCUT Serie: Standard Line Bezeichnung: Spiralbohrer Daten Durchmesser: 10,5 mm Gesamtlänge: 168 mm Spirallänge: 87 mm Spitzenwinkel: 118° Verpackungseinheit: 1 Besonderheiten Material: HSS Schaft: Morsekegel Norm: DIN 345 Farbe: Schwarz Ausführung: rollgewalzt Anwendung: Bohrer für Metall FAQ Für welche Maschinen ist dieser Bohrer geeignet? Der MetavCUT Spiralbohrer mit Morsekegelschaft (SKU 54105-FDA) ist primär für Säulenbohrmaschinen und Drehmaschinen mit MK-Aufnahme konzipiert, wodurch ein sicherer Sitz und hohe Drehmomentübertragung gewährleistet sind. Eignet sich der Bohrer für Baustahl und Gusseisen? Ja, der HSS Spiralbohrer aus der Standard Line von MetavCUT (54105-FDA) ist für Baustahl, Gusseisen und weitere Nichteisenmetalle ausgelegt und arbeitet zuverlässig bis etwa 900 N/mm² Zugfestigkeit. Wie wirkt sich die rollgewalzte Fertigung auf die Anwendung aus? Die rollgewalzte Ausführung macht den Spiralbohrer robuster gegenüber Bruch und wirtschaftlicher in der Fertigung; das reduziert Ausfälle bei Standardbohrungen und verlängert die Nutzungsdauer im Werkstattalltag. Welchen Spitzenwinkel hat der Bohrer und was bedeutet das praktisch? Der Bohrer hat einen Spitzenwinkel von 118°; das erleichtert das Zentrieren in weicheren Werkstoffen wie Aluminium und reduziert das Wandern beim Anbohren. Warum sollte ich den Bohrer von MetavCUT wählen? MetavCUT kombiniert HSS-Materialqualität mit standardisiertem Design und der Verlässlichkeit von Metav als Anbieter; die SKU 54105-FDA steht für einen universellen, wirtschaftlichen Bohrer für den professionellen Einsatz.
10,5mm Spiralbohrer, 135° Spitze, HSS‑G geschliffen, reduziert 10mm Schaft, 87mm Spirallänge, DIN 338 - MetavCUT
Kombination aus HSS-G und geschliffener Ausführung liefert präzise Bohrlöcher bei hoher Standzeit; der reduzierte Schaft 10mm erlaubt die Nutzung in Bohrfuttern mit begrenzter Spannweite. Profitieren Sie von schnellerem Vorschub und reduziertem Kraftaufwand bei der Metallbearbeitung und kontaktieren Sie bei Bedarf die Metav-Beratung für technische Details. Spiralbohrer»MetavCUT Standard Line« (63105-FDA) Spiralbohrer»MetavCUT Standard Line« für präzise Metallbohrungen in Werkstatt und Industrie, geschliffen und ausgelegt für legierte und unlegierte Stähle sowie Nichteisenwerkstoffe HSS-G geschliffen für hohe Schärfe DIN 338 Konformität für kurze Spiralbohrer Reduzierter Schaft 10 mm passt in kleine Bohrfutter Spitzenwinkel 135° für härtere Werkstoffe Spirallänge 87 mm für sicheres Spanabführen Schnelleres Bohren bei geringer Anpresskraft Der geschliffene HSS-G-Schliff sorgt für sehr scharfe Schneiden und ermöglicht bis zu 40 % schnelleres Bohren bei gleichzeitig bis zu 50 % geringerer Anpresskraft im Vergleich zu herkömmlichen HSS-Bohrern. Für Anwender bedeutet das weniger Ermüdung bei längerem Arbeiten und kürzere Taktzeiten in der Werkstatt. Bei harten Werkstoffen empfiehlt sich Kühlung, um Standzeit und Bohrbild zu optimieren. Präzision und Rundlaufgenauigkeit für saubere Bohrbilder Dank der DIN 338-Konformität und des geschliffenen Werkzeugs überzeugt der Bohrer mit sauberem Bohrbild und hoher Rundlaufgenauigkeit. Der reduzierte Schaft 10mm erleichtert die Einspannung in Bohrfutter mit begrenzter Backenöffnung, ohne Kompromisse bei der Stabilität in stationären Maschinen einzugehen. Für hochpräzise Passungen sollte vorgepunzt oder zentriert werden. Vielseitiger Einsatz in Werkstatt und Produktion Mit einem Durchmesser von 10,5 mm liegt das Werkzeug im Standard-Bereich für allgemeine Werkstattanwendungen. Es eignet sich für Dünn- bis Mittelstarke Bleche, Profile, Guss- und Sintermaterialien sowie Temperguss. Für Handgeführte Maschinen empfiehlt sich eine kontrollierte Vorschubgeschwindigkeit; für langlebige Serien empfiehlt sich stationärer Einsatz mit geeigneter Kühlung. Materialeigenschaften und Hinweise zur Lebensdauer Das Material HSS-G kombiniert Zähigkeit und Schärfe, ist jedoch aufgrund des Schleifprozesses empfindlicher gegen Stoßbelastungen als walzgewalzte Varianten. Bei der Bearbeitung von harten Materialien wie Edelstahl hilft der Spitzenwinkel 135°, den Anbohrwiderstand zu reduzieren und das Abdriften zu minimieren. Eine angepasste Schnittgeschwindigkeit und Kühlmittel verlängern die Standzeit deutlich. Setzen Sie auf die MetavCUT Standard Line für zuverlässige, präzise Metallbohrungen; bei Fragen erreichen Sie die Metav-Beratung per eMail info@metav-werkzeuge.com oder Telefon +49 2822 7131930 Produktmerkmale Artikelnummer: 63105-FDA Marke: MetavCUT Bezeichnung: Spiralbohrer Serie: Standard Line Material: HSS-G Norm: DIN 338 Fakten Durchmesser: 10,5 mm Gesamtlänge: 133 mm Spirallänge: 87 mm Spitzenwinkel: 135° Verpackungseinheit: 1 Besonderheiten Schaftausführung: reduziert 10 mm Ausführung: geschliffen Farbe: silber HSS-G: geschliffen, hohe Schärfe und Rundlaufgenauigkeit FAQ Für welche Materialien eignet sich der Bohrer am besten? Der MetavCUT Spiralbohrer aus der Standard Line ist ausgelegt für legierte und unlegierte Stähle, Gussstahl, Gusseisen, Sintereisen, Temperguss sowie Nichteisenmetalle und Hartkunststoffe; für besonders harte Werkstoffe empfiehlt sich die Nutzung mit Kühlmittel. Passt der Bohrer in Bohrfutter mit 10 mm Spannbereich? Ja, durch den reduzierten Schaft 10 mm lässt sich der Spiralbohrer sicher in Bohrfutter mit begrenzter Spannweite einspannen, ohne den Bohrdurchmesser zu reduzieren. Ist der geschliffene Bohrer für Handgeführte Maschinen geeignet? Der geschliffene HSS-G-Bohrer eignet sich grundsätzlich für Handgeführte Maschinen im Standard-Bereich, allerdings ist bei präzisen oder stoßgefährdeten Anwendungen stationärer Einsatz mit Kühlung zu bevorzugen. Warum wurde ein Spitzenwinkel von 135° gewählt? Der Spitzenwinkel 135° reduziert das Anbohrmoment bei harten Werkstoffen und erzeugt saubere Einstiche, wodurch das Risiko von Abdriften und Aufrauen des Bohrrandes minimiert wird.
10.1mm HSS Twist Drill DIN 338 ,short, roll forged, black, Type N - MetavCUT
Die Kombination aus HSS-Werkstoff und kurzer Ausführung sorgt für hohe Stabilität und zuverlässige Metallbearbeitung; die Einhaltung der DIN 338 garantiert Normkonformität und Austauschbarkeit. Bestellen Sie den Spiralbohrer direkt über Metav Werkzeuge oder fragen Sie unsere Beratung bei Bedarf an. Spiralbohrer 10,1 mm Typ N von MetavCUT Der Spiralbohrer 10,1 mm ist ein kurzer HSS-Bohrer nach DIN 338, ausgelegt für präzise Metallbohrungen an Handbohrmaschine und stationären Maschinen. HSS für legierten und unlegierten Stahl Kurze Ausführung für erhöhte Stabilität DIN 338 Normkonformität für Austauschbarkeit Spitzenwinkel 118° für einfache Zentrierung Zylinderschaft kompatibel mit Handbohrmaschine Mehr Präzision durch kurze Bauart und stabile Führung Die kurze Ausführung reduziert die Auskraglänge und erhöht dadurch die Stabilität beim Bohren in Metall. Diese Bauweise verringert das Risiko von Vibrationen und Bohrerverwindung, was zu saubereren Bohrbildern und längerer Standzeit führt. Für Anwender bedeutet das weniger Nacharbeit und bessere Passgenauigkeit bei Montagebohrungen. HSS-Material für vielseitige Werkstoffeinsatzmöglichkeiten Der Einsatz von HSS (Schnellarbeitsstahl) macht den Bohrer elastisch und widerstandsfähig gegen Bruch, besonders bei Durchmessern unter 6 mm, bleibt aber auch bei 10,1 mm robust für viele Anwendungen. HSS eignet sich für legierten und unlegierten Stahl, Gusseisen, Nichteisenmetalle und Kunststoffe, wodurch der Bohrer in Werkstatt und Produktion vielseitig verwendet werden kann. Passgenau für Metallarbeiten und einfache Maschinenanbindung Durch die Auslegung nach DIN 338 ist die Fertigung und der Schaftstandard garantiert, was die Einspannbarkeit in handelsübliche Handbohrmaschine erleichtert. Der Zylinderschaft sorgt für sicheren Halt im Bohrfutter und minimiert das Durchrutschen bei hohen Vorschubkräften. Anwender profitieren von schneller Werkzeugwechselbarkeit und konstanter Bearbeitungsqualität. Praktische Hinweise zu Spitzenwinkel und Anbohrtechnik Der voreingestellte Spitzenwinkel von 118° ist optimal für allgemeine Metallarbeiten und erleichtert das Zentrieren auf ebener Fläche. Bei gehärteten Werkstoffen oder bei Bedarf an reduzierter Anbohrzeit empfiehlt sich ein größerer Winkel oder ein Vorbohren mit Zentrierbohrer. Richtiges Kühlen und moderate Vorschubgeschwindigkeiten verlängern die Standzeit merklich. Empfehlung: Für präzise und stabile Metallbohrungen den MetavCUT HSS Spiralbohrer Typ N wählen und bei Detailfragen die technische Beratung per eMail info@metav-werkzeuge.com oder Telefon +49 2822 7131930 kontaktieren_ Produktmerkmale Artikelnummer: 40101-FDA Marke: MetavCUT Bezeichnung: Spiralbohrer Material: HSS Norm: DIN 338 Typ: Typ N Farbe: schwarz Verpackungseinheit: 5 Fakten Durchmesser: 10,1 mm Gesamtlänge: 133 mm Spirallänge: 87 mm Spitzenwinkel: 118° Besonderheiten Ausführung: kurz Einsatzgebiet: Bohrer für Metall Für Bohrmaschine: Handbohrmaschine SKU: 40101-FDA FAQ Ist der Bohrer für Edelstahl geeignet? Der MetavCUT Spiralbohrer Typ N aus HSS eignet sich für viele Stahlsorten, bei sehr hartem Edelstahl sollten jedoch spezielle Beschichtungen oder ein größerer Spitzenwinkel in Erwägung gezogen werden. Welche Maschine wird empfohlen? Für optimale Ergebnisse empfiehlt sich die Verwendung an stationärer Säulenbohrmaschine oder einer leistungsfähigen Handbohrmaschine; durch den Zylinderschaft ist der Bohrer einfach zu spannen. Wie wirkt sich die kurze Ausführung auf die Standzeit aus? Die kurze Ausführung erhöht die Stabilität und reduziert Schwingungen, was in der Regel zu geringerer Werkzeugbelastung und damit zu längerer Standzeit führt. Wird der Bohrer einzeln oder als Set geliefert? Die Verpackungseinheit beträgt 5 Stück; das Produkt ist unter der Artikelnummer 40101-FDA gelistet.
10.1mm HSS-E Twist Drill DIN 338 ,short, 5% cobalt-alloyed, Type N - MetavCUT
Der kurze Spiralbohrer von MetavCUT kombiniert HSS-E-Legierung mit 5% Kobalt für erhöhte Elastizität und verringerte Bruchgefahr sowie eine Kurzbauweise, die Stabilität und Präzision beim Bohren in Stahl verbessert. Nutzen Sie diese Merkmale für sauberere Bohrbilder und längere Standzeiten und bestellen Sie den Bohrer direkt über Metav Werkzeuge oder fragen Sie unsere Beratung bei Bedarf an. Spiralbohrer 10,1 mm – HSS-E Kurz (MetavCUT) Der Spiralbohrer in Kurz-Ausführung eignet sich für präzises Bohren in Stahl, Gusseisen und Nichteisenmetallen und für den Einsatz in Handbohrmaschine und stationären Maschinen. Kurzbauweise für hohe Stabilität HSS-E mit 5% Kobaltlegierung Geschliffene Schaftgeometrie für präzise Bohrbilder Spitzenwinkel 135° für harte Werkstoffe Normkonform nach DIN 338 Höhere Standzeit durch HSS‑E mit Kobalt Die HSS-E-Legierung mit 5% Kobalt erhöht die Warmfestigkeit und die Elastizität des Werkzeugs, wodurch das Bruchrisiko bei kleinen Durchmessern reduziert wird. Dies macht den Bohrer besonders geeignet für wiederkehrende Metallbearbeitung unter wechselnden Temperaturen. Anwender profitieren von einer längeren Nutzungsdauer und geringeren Werkzeugwechseln, was die Effizienz in Werkstatt und Produktion steigert. Kurzbauweise für Präzision und Stabilität Durch die Kurzbauweise reduziert sich die Auskraglänge, was die Stabilität und Rundlaufgenauigkeit erhöht. Besonders bei Bohrungen in harten Materialien lässt sich so die Abweichung des Bohrbildes minimieren. Die Konstruktionsweise eignet sich damit für präzise Arbeiten in der Montage und für Anwendungen, bei denen enge Toleranzen gefordert sind. Geschliffene Geometrie und 135° Spitzenwinkel Die geschliffene Schaftausführung sorgt für sehr scharfe Schneiden und hohe Rundlaufgenauigkeit; saubere und präzise Bohrlöcher sind die Folge. Der 135° Spitzenwinkel erleichtert das Anbohren von harten Werkstoffen wie Edelstahl und reduziert das Auslaufen beim Eintritt. Für stationäre Anwendungen und für Bohrungen mit Kühlung empfiehlt sich der Einsatz geschliffener Ausführungen, um die beste Genauigkeit zu erreichen. Geeignet für Werkstatt, Montage und präzise Anwendungen Der MetavCUT Spiralbohrer vom Typ N entspricht der DIN 338 und richtet sich an Anwender in Werkstatt, Handwerk und leichten Industrieanwendungen, die Wert auf präzise Metallbohrungen legen. Einsatzgebiete sind das Durchbohren von legiertem und unlegiertem Stahl, Gusseisen sowie Nichteisenmetallen und Kunststoffen. Praxistipp: Vorzentrieren verbessert die Genauigkeit bei Handbohrmaschine erheblich. Empfehlung: Setzen Sie auf die Kurz-Ausführung von MetavCUT für stabile, präzise Metallbohrungen und kontaktieren Sie bei Detailfragen unser Team per eMail info@metav-werkzeuge.com oder Telefon +49 2822 7131930. Produktmerkmale Artikelnummer: 47101-FDA Marke: MetavCUT Serie: Standard Line Bezeichnung: Spiralbohrer Norm: DIN 338 Daten Durchmesser: 10,1 mm Gesamtlänge: 133 mm Spirallänge: 87 mm Spitzenwinkel: 135° Besonderheiten Material: HSS-E (Schnellarbeitsstahl) Farbe: 5% Kobaltlegiert Schaftausführung: Geschliffen (CNC-Schliff für hohe Präzision) Typ: Typ N (Normalspirale für Metall) Ausführung: Kurz Für Bohrmaschine: Handbohrmaschine FAQ Ist der Spiralbohrer von MetavCUT für Edelstahl geeignet? Der Spiralbohrer 10,1 mm von MetavCUT mit 135° Spitzenwinkel und HSS-E-Kobaltlegierung ist für das Bohren in harten Werkstoffen einschließlich Edelstahl geeignet; für beste Ergebnisse Kühlung und angepasste Schnittgeschwindigkeit einsetzen. Kann der Bohrer in Handbohrmaschine verwendet werden? Ja, der Bohrer ist für die Verwendung in der Handbohrmaschine ausgelegt, profitiert aber von ruhiger Führung und Vorzentrierung, um Rundlaufabweichungen zu vermeiden. Welche Vorteile bietet die geschliffene Schaftausführung? Die geschliffene Ausführung liefert schärfere Schneiden und eine höhere Rundlaufgenauigkeit, wodurch sauberere Bohrbilder und präzisere Passungen erreicht werden. Entspricht der Bohrer einer Norm und wofür steht Typ N? Der Bohrer entspricht DIN 338; Typ N bezeichnet die Normalspirale, die sich besonders für Metallbohrungen eignet.
10.25mm HSS Twist Drill DIN 338 ,short, roll forged, black, Type N - MetavCUT
Twist Drill (Type N) – 10.25 mm, 118° tip, Short HSS, DIN 338, Black The Twist Drill (Type N) is a short HSS metal drill designed for precise drilling with hand or drilling machines, delivering stability and reliable performance for a wide range of metalworking applications. Short HSS construction for high stability 10.25 mm diameter for medium-sized holes 118° tip for reliable centring and control Conforms to DIN 338 for short twist drills Suitable for use with Drilling Machine and hand drills Durable HSS construction for dependable metalworking High-Speed Steel (HSS) gives this short twist drill a balanced combination of hardness and toughness, making it suitable for drilling alloyed and unalloyed steel, cast iron, non-ferrous metals and many plastics. The roll-formed manufacturing process commonly used for these drills improves elasticity and reduces the risk of breakage under normal machining loads. This results in a tool that stands up to repeated use while maintaining cutting performance and service life. Short design and DIN 338 deliver rigidity and precision The short execution specified by DIN 338 reduces overhang and therefore limits bending and chatter during operation. With a Spiral Length of 87 mm and an Overall Length of 133 mm for the 10.25 mm variant, the geometry improves stability and enables more accurate, straighter holes when compared with longer drills. This makes the tool particularly useful where precision and minimal runout are required. Optimised geometry for controlled entry and guided drilling A 118° tip angle provides a good compromise between centring ability and cutting efficiency for many metal applications; a modest tip angle reduces walking on curved or slightly uneven surfaces and supports controlled feed rates. The Type N normal spiral flute is the classic choice for metal drilling, offering reliable swarf evacuation in standard conditions. The black finish aids corrosion resistance and handling visibility in the work area. Practical use, sharpening and support Because the cutting point is formed to a defined angle, the Twist Drill achieves consistent entry and reduced lateral forces; sharpening restores the cutting edges and prolongs tool life. The reduced cross-edge at the tip lowers friction and required feed forces, improving centring and performance in through-hole operations. For any questions about sharpening, tool life or the correct drill choice for a specific material, METAV Werkzeuge provides competent advice and technical support to ensure the right setup for your task. Choose the MetavCUT Twist Drill (Type N) for precise metal drilling and contact METAV Werkzeuge for tailored technical advice by email at info@metav-werkzeuge.com, by phone at +49 2822 7131930 or via WhatsApp at +49 170 2837271 Designation: Twist Drill Brand: MetavCUT SKU: 401025-FDA Diameter: 10.25 mm Tip Angle: 118° Spiral Length: 87 mm Overall Length: 133 mm Execution: Short Material: HSS Type: Type N Norm: DIN 338 Colour: Black Application: Drills for metal Suitable for: Drilling Machine Manufacturer: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What is the Twist Drill from MetavCUT (Type N) mainly used for? The MetavCUT Twist Drill (Type N) is primarily used for the machining of high-strength materials and larger hole diameters; it is the standard tool for metalworking where robustness is required. Its form allows relatively easy resharpening and reliable performance under higher loads. Which three drill types are commonly distinguished? There are three main drill categories: metal drills, wood drills, and stone/concrete drills; the MetavCUT Twist Drill (Type N) belongs to the metal drill group and is optimised for metals rather than masonry or timber. Can the MetavCUT Twist Drill (Type N) be used with a hand drill or should it only be used on machine tools? The MetavCUT Twist Drill (Type N) is suitable for both hand drills and stationary drilling machines, provided the correct speeds and clamping are used; for best results ensure a rigid setup and appropriate cutting parameters for the material. Why are twist drills pointed and what benefit does this give when using the MetavCUT Twist Drill (Type N)? Pointing reduces the cross-cutting edge at the tip, which lowers friction and required feed forces; as a result the MetavCUT Twist Drill (Type N) centres more reliably in the workpiece and requires less thrust, improving hole quality and tool guidance.
10.2mm HSS Twist Drill DIN 338 ,short, roll forged, black, Type N - MetavCUT
Twist Drill Type N — Short HSS Drill, 10.2 mm, 118°, Black, DIN 338 A Twist Drill Type N for precise metalworking, designed as a short HSS bit for drilling machines and hand drills in demanding workshop and industrial applications. Short design for high stability and precision HSS construction for wear resistance on metals Conforms to DIN 338 for short twist drills 118° point angle for reliable centring on metals Suitable for Hand Drill and Drilling Machine use Precision and short design for stable metalworking The short configuration of this Twist Drill reduces overhang and improves rigidity, resulting in greater accuracy when drilling into metal. Because the exposed length is minimised, the tool resists bending and chatter, which improves hole quality and tool life. This makes the bit particularly suitable where tight tolerances are required or where accessibility limits the use of longer drills. HSS material and durability for standard metal tasks Manufactured from HSS (High Speed Steel), the drill offers a balance of hardness and toughness for typical metalworking jobs. The material choice reduces the risk of breakage during operations under 6 mm and provides reliable wear resistance on alloyed and unalloyed steel, cast iron, non-ferrous metals and plastics. For users unfamiliar with the term, HSS means the bit maintains cutting performance at higher temperatures than standard steels. Optimised tip geometry for efficient cutting and centring A 118° point angle gives the bit good initial penetration and easier centring on slightly curved or soft surfaces, helping to start holes without wandering. For harder steels, a different point geometry can be used, but the 118° tip on this short Type N drill ensures lower thrust force and precise starts in common workshop materials, so operators can rely on consistent hole positioning. Application scope and machine compatibility Designed according to DIN 338 as a short twist drill with a cylindrical shank, this bit is intended for metalworking on both stationary machines and portable tools such as the Hand Drill or Drilling Machine. The Type N normal spiral is optimised for drilling metals rather than soft timber; use in wood is possible but guidance and finish may be inferior compared with dedicated wood drills. Who benefits from this drill and how it improves workflow Workshop technicians, maintenance staff and tradespeople who need robust, repeatable metal drilling will value the stability and service life of this short Twist Drill. By reducing deflection and improving centring, it lowers scrap rates and rework, which translates into more efficient production and fewer interruptions for tool changes. Choose MetavCUT’s robust HSS Twist Drill Type N for dependable metalworking performance and contact METAV Werkzeuge for expert advice and application support via eMail info@metav-werkzeuge.com, Phone +49 2822 7131930 or WhatsApp +49 170 2837271 Technical specifications Designation: Twist Drill Marke: MetavCUT SKU: 40102-FDA Type: Type N Diameter: 10.2 mm Spiral length: 87 mm Overall length: 133 mm Point angle: 118° Execution: Short Material: HSS Standard: DIN 338 Colour: Black For: Hand Drill / Drilling Machine Application: Drills for metal Hersteller: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What materials is the MetavCUT Twist Drill Type N best suited for? The MetavCUT Twist Drill Type N is intended primarily for metalworking; its HSS construction and normal spiral geometry make it suitable for alloyed and unalloyed steel, cast iron and non‑ferrous metals, and it can also be used for plastics with appropriate speeds and feeds. Can this short Twist Drill be used in a handheld drilling machine? Yes, the short design and cylindrical shank of the MetavCUT Twist Drill Type N permit use in both stationary machines and a Hand Drill or Drilling Machine, offering improved stability and reduced tendency to bend compared with longer drills. What is a Twist Drill used for? A Twist Drill is mainly applied to the machining of high‑strength materials and larger bore diameters; its geometry allows relatively simple re‑grinding and it withstands substantial forces, making it a common choice in metalworking where durability and reliable chip removal are required. Which three drill types exist? The three primary drill types are Metal Drill (often HSS), Wood Drill, and Masonry/Concrete Drill. Each is optimised for its specific material class and cutting conditions.
10.2mm HSS-E Twist Drill DIN 338 ,short, 5% cobalt-alloyed, Type N - MetavCUT
Twist Drill – Short HSS‑E Metal Drill, 10.2 mm, 135° Point Angle, Type N, 5% Cobalt‑Alloyed, Fully Ground, DIN 338 The Twist Drill is a short HSS‑E metal drill designed for precise machining in hard materials, combining a 10.2 mm Diameter and a 135° Point Angle for improved centring and wear resistance in metalworking. Twist Drill 10.2 mm Type N for metalworking Short design for higher stability and accuracy 5% cobalt‑alloyed material for heat resistance Fully ground shaft for high runout precision Conforms to DIN 338 for short HSS twist drills High performance in hard materials thanks to cobalt alloy A Short Twist Drill made from HSS‑E with 5% cobalt‑alloyed composition delivers increased red hardness and greater wear resistance when drilling alloys and stainless steels. The cobalt addition raises the temperature tolerance of the Cutting Edge, so holes remain accurate for longer under thermal load. This results in fewer tool changes and more consistent hole quality during repetitive metalworking tasks. Stability and precision through shorter overhang and ground geometry The Short design with an overall length of 133 mm and a Spiral Length of 87 mm reduces deflection and vibration compared with standard long drills. A fully ground shaft and CNC‑ground flute geometry provide superior Runout Accuracy and produce clean, precise holes in demanding applications. For workshop setups and bench drilling where rigidity matters, this configuration minimises breakout and improves positional accuracy. Engineered for metal: Type N geometry and 135° point angle The Type N normal spiral profile and a 135° Point Angle are optimised for harder metals and stainless steels, improving centring and reducing the tendency to grab during start‑up. The ground flute form yields sharp cutting lips for smooth chip evacuation. For users less familiar with drill terminology: ground drills are produced by grinding the flute geometry into the blank, giving finer cutting edges and better concentricity than rolled alternatives, at the expense of somewhat higher brittleness. Best uses and recommendations for professionals and trades Designed for metalworkers, toolrooms and maintenance professionals, this Twist Drill excels when machining alloyed and unalloyed steel, cast iron, non‑ferrous metals and engineering plastics. For optimal tool life, use appropriate cutting fluid and moderate feed rates, especially in portable drilling machines or stationary drilling equipment. The Short version is particularly suited to tasks requiring tight tolerances and minimal runout. Manufacturing standard and handling guidance Manufactured in accordance with DIN 338 as a short HSS twist drill with cylindrical shank, this tool follows industry specifications for geometry and dimensions. The Roll‑or‑Grind distinction: this model is ground, which produces superior hole quality and concentricity. When drilling holes up to common diameters and depths, ensure correct clutch settings or drill press speeds to match the HSS‑E material and Point Angle for consistent results. Highly recommended: Opt for the MetavCUT Twist Drill when precision in hard metals is required — for technical questions or personalised advice METAV Werkzeuge offers comprehensive support via email info@metav-werkzeuge.com, phone +49 2822 7131930 or WhatsApp +49 170 2837271 Technical Data Designation: Twist Drill (Short Spiral Drill) Brand: MetavCUT SKU: 47102-FDA Diameter: 10.2 mm Material: HSS‑E Alloying: 5% cobalt‑alloyed Type: Type N Point Angle: 135° Spiral Length: 87 mm Overall Length: 133 mm Shank Execution: fully ground Execution: short Standard: DIN 338 Application: Drills for metal Suitable for: Drilling Machine / Hand drilling applications Hersteller: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What is the primary use of this Twist Drill from MetavCUT and for which materials is it best suited? The MetavCUT Twist Drill is primarily used for machining high‑strength materials and larger metal hole diameters; its short design and HSS‑E composition with 5% cobalt make it particularly suitable for alloyed and unalloyed steel, cast iron, non‑ferrous metals and certain plastics, offering good wear resistance and heat tolerance during metal drilling. Which three drill types are commonly distinguished and how does the MetavCUT Twist Drill fit in? The three common drill types are metal drills, wood drills and stone/concrete drills. The MetavCUT Twist Drill belongs to the metal drill category and is engineered for metalworking tasks with a Type N geometry and HSS‑E material properties.
High-performance drill bits for demanding production
Drill bits designed for industrial manufacturing where precision, repeatability and tool life are decisive. Based on a spectrum from HSS and kobalt-alloyed hss-e for universal use to solid carbide drills for high-speed, high-precision serial production, this range covers applications from general engineering to automotive supplier work.
Why these drill bits are essential in the workshop and on the machining centre
Function and behaviour:
- primary use: creating accurate cylindrical holes
- typical machines: CNC machining centres, lathes and drill presses
- key design aspects: optimised chisel edge, defined point angles, flute geometry for reliable chip evacuation
Technical advantages and process benefits:
- reduced feed forces through optimised point geometry
- improved heat control with advanced coatings and, where specified, internal coolant supply
- extended tool life using solid carbide variants and multilayer coatings such as TiN / TiAlN
- process security on challenging materials thanks to tailored materials and geometries
Concrete benefits that boost productivity and quality
- predictable tool life and fewer tool changes, lowering machine downtime
- stable hole quality and consistent tolerances across long runs
- efficient chip control and thermal management for safe deep-hole and hardened-material drilling
- suitability across a wide material range, reducing the need for multiple specialised tools
Metav as a reliable partner for high-precision tooling
Metav combines decades of sector expertise with a broad, dependable offering from its Emmerich facility. With over 48,000 customers and more than 250,000 products, Metav positions its range of drill bits, twist drills and indexable drills as a practical, quality-first choice for procurement managers and production engineers seeking dependable supply and technical competence.
Technical data (at a glance)
- material: HSS, kobalt-alloyed hss-e, solid carbide
- coatings: TiN, TiAlN, advanced nanocoatings
- coolant option: internal coolant feed where specified
- typical applications: mild steel, high-alloy stainless steel, cast iron, non-ferrous metals, technical plastics, hardened materials (use solid carbide variants)
- tool types available: twist drills, solid carbide drills, indexable drills, centre and pilot drills, step drills
FAQ
What is the difference between hss and solid carbide drill bits?
HSS drill bits offer toughness and resistance to breakage for general machining, while solid carbide drills provide higher wear resistance and are the preferred choice for high-speed, high-volume machining and hardened materials.
Which coatings improve tool life for industrial drilling?
Coatings such as TiN and TiAlN increase surface hardness and thermal stability; when combined with the correct drill geometry and, if available, internal coolant, they significantly extend the service life of drill bits.
Can these drill bits be used on CNC machining centres for deep holes?
Yes. Drill bits designed with optimised flute geometry and internal coolant supply are suited to deep-hole machining on CNC machining centres, ensuring controlled chip evacuation and heat management.
How should I choose between twist drills, solid carbide drills and indexable drills?
Select twist drills for general-purpose drilling, solid carbide drills for high-speed and hardened-material applications, and indexable drills for large-diameter holes where insert changes offer economic advantages.
Why choose Metav for drill bits and drilling solutions?
Metav offers a comprehensive selection of drill bits, twist drills and indexable drills combined with sector expertise, centralised supply from Emmerich and proven reliability across thousands of industrial customers.
Fragen zu diesen Produkten??
Mit mehr als 30 Jahren Erfahrung beraten wir Sie gerne persönlich.
Tel.: +49 2822 7131930
Mail: info@metav-werkzeuge.com