Precision cut-off tools for accurate grooving and part-off operations
Cut-off tools are narrow holder systems for lathes designed to produce precise grooves and part-offs, offering reliable control when machining steels and other workpiece materials where clean separation is essential. They serve as either solid clamp-style holders or flat tool blades fitted with indexable carbide inserts, and when equipped with internal coolant channels they deliver high-pressure coolant directly to the insert to control heat and evacuate chips efficiently. Using these tools reduces the risk of chip jamming, surface damage and sudden tool failure while improving repeatability, particularly in deep grooving and tough materials where external coolant is insufficient. Key advantages include enhanced cutting stability, extended insert life and consistent part quality through optimised chip evacuation and thermal management.
39 Stechklemmhalter S32S 4C For Wendeplatten Innenkühlung Schneidbreite 4mm Schneidenhöhe 60mm Schaft 32mm Gesamtlänge 250mm - Teknik Makina
Robust clamping and proven insert compatibility deliver repeatable grooves and secure parting operations; the combination of a rigid shank and precise insert seating supports stable cutting and reduced rework. Order the part via Metav Werkzeuge or consult their specialists for application-specific advice. Grooving clamp holder K728TM — 4C insert holder with 32 mm shank by Teknik Makina A grooving clamp holder engineered for narrow-groove and parting operations that accepts Sandvik 4C indexable inserts and fits an S32S shank standard Rigid 32 mm shank for stable mounting Compatible with Sandvik 4C indexable inserts 4 mm cutting width for narrow grooving 60 mm cutting height for deep cuts 250 mm overall length for extended reach Stable interface for repeatable turning and parting The combination of a 32 mm shank and a solid clamp design produces a stable mounting that limits vibration and improves surface finish. In practical terms, a stiffer holder reduces tool chatter and contributes directly to longer insert life and fewer rejected parts. The holder’s mass is balanced for lathe use; its measured weight supports predictable dynamics at common spindle speeds. Specified mounting dimensions allow straightforward integration into existing tool posts, enabling reliable, repeatable set-ups and shorter machine idle time. Consistent groove geometry with indexable insert support Designed around the Sandvik 4C insert form, the holder provides a secure seat for indexable cutting edges so that single-seat tightening delivers consistent radial and axial positioning. The 4 mm cutting width combined with a 60 mm cutting height supports both narrow grooving and moderate-depth parting, giving a predictable chip control strategy when paired with suitable insert grades. The indexable system simplifies changing edges: worn corners are rotated or replaced without refacing the holder, reducing maintenance time and supporting continuous production. Workshop-ready reach, designation and handling With a 250 mm overall length and an S32S ISO shank designation, the holder offers extended reach for overhang applications while maintaining a known interface to standard lathe toolposts. The unit’s design facilitates quick clamping of the insert and reliable torque transmission from clamp screw to insert seat. Identified in the range as K728TM, this grooving clamp holder is suitable where secure insert retention and predictable cutting geometry are priorities. For additional technical clarification, Metav’s consultants can provide machining parameter guidance and check compatibility with existing fixtures. Contact Metav Werkzeuge for tailored application advice and to arrange supply of the Teknik Makina K728TM grooving clamp holder directly from Emmerich Technical Data SKU: K728TM Manufacturer: Teknik Makina Facts Shank diameter: 32 mm Overall length: 250 mm Cutting height: 60 mm Cutting width: 4 mm Diameter: 39 mm Weight: 2.854 kg Special features Compatible inserts: 4C Compatible insert manufacturer: Sandvik Shank designation: S32S Secondary designation: 4C-R-123 SDV FAQ What insert type fits this holder? The holder accepts 4C indexable inserts and is specified for use with Sandvik 4C insert geometries, ensuring correct seating and repeatability for the K728TM grooving clamp holder. Which shank does the tool require for mounting? Mounting requires a 32 mm shank interface; the product is manufactured to the S32S shank designation for standard lathe toolpost compatibility. What groove widths and depths is the holder designed for? The design supports a 4 mm cutting width and a 60 mm cutting height, suitable for narrow grooving and moderate-depth parting tasks when paired with appropriate insert grades. Is the K728TM suitable for extended reach applications? Yes, the 250 mm overall length provides additional reach for overhang requirements while maintaining secure insert clamping for stable machining. Manufacturer / Responsible: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com
39mm Stechklemmhalter 3mm Cutting Width 50mm Cutting Height S32S Shaft 250mm Overall Length For 4C ZT.D Inserts 3C-R ZT.D Shank, Innenkühlung Rechtsschneidend - Teknik Makina
Take advantage of the combination of a robust 32 mm shank and a precise 3 mm cutting width for stable, low-vibration parting that extends insert life; order the parting tool clamp holder K682TM directly via Metav Werkzeuge or ask our consultants if needed Parting tool clamp holder K682TM — 32 mm shank, 3 mm cutting width (Teknik Makina) The Parting tool clamp holder is a clamp-style holder designed for parting and grooving operations in turning applications, offering secure mounting and compatibility with ZCC 4C ZT.D inserts 32 mm shank for secure lathe mounting 3 mm cutting width for precise parting Compatible with ZCC 4C ZT.D inserts Stable clamping for consistent parting quality The compact clamp design delivers a stable, low-vibration setup that supports repeatable results in serial turning tasks. With a 32 mm shank, the holder fits common lathe tool posts and reduces flex under cutting forces; this stability leads directly to longer insert life and fewer rejects. The mass of the unit, at 1.641 kg, further damps chatter during cut-off operations, turning machine time into reliable, measurable productivity gains. Engineers and workshop managers will appreciate the predictable behaviour when switching from roughing to finishing cuts. Narrow kerf and high cutting clearance for material-saving cuts A narrow 3 mm cutting width combined with a 50 mm cutting height offers a slim kerf that reduces material waste while allowing effective chip evacuation in most steels and non-ferrous alloys. The design supports fine parting and grooving tasks where minimal material removal and tight tolerances are required. The 250 mm overall length provides adequate reach for deeper or awkward set-ups without compromising rigidity, enabling precision finishing operations with less secondary machining. Fit and integration with existing tool systems The holder is specified with an S32S shank designation and pairs with standard clamp interfaces, so it integrates easily into established turning tool lines. It accepts ZCC inserts in the 4C ZT.D format and aligns with the holder designation 3C-R ZT.D, making insert selection straightforward and supply chains simpler. This compatibility minimises downtime for tool changes and reduces inventory complexity, which is advantageous in workshops seeking leaner logistics. Designed for everyday workshop reliability Manufactured to withstand routine industrial use, the clamp-style holder is a pragmatic choice for workshops and small production facilities that prioritise uptime. The combination of a secure clamp mechanism and standardised interface supports quick reindexing of inserts and efficient tool maintenance. The result is a dependable solution that balances durability with the operational ease required in high-mix, low-to-medium volume turning environments. Contact Metav Werkzeuge for supply and technical advice on the Teknik Makina parting tool clamp holder K682TM with its 32 mm shank and 3 mm cutting width; call +49 2822 7131930 or eMail info@metav-werkzeuge.com Technical data Article number: K682TM Manufacturer: Teknik Makina Dimensions & weights Shank diameter: 32 mm Overall length: 250 mm External diameter: 39 mm Cutting height: 50 mm Cutting width: 3 mm Weight: 1.641 kg Compatibility & features Compatible inserts: 4C ZT.D Compatible insert manufacturer: ZCC Shank designation: S32S Holder designation: 3C-R ZT.D FAQ Which inserts fit this holder? The parting tool clamp holder K682TM is specified for ZCC inserts in the 4C ZT.D format and works with the corresponding 3C-R ZT.D holder designation. What shank size is required for the tool post? The tool requires a 32 mm shank seat, noted as S32S, for correct mounting and to ensure the designed rigidity. How deep can the holder reach in typical setups? With an overall length of 250 mm and a cutting height of 50 mm, the holder supports deeper parting operations while maintaining stability. Is the holder heavy enough to reduce chatter? At 1.641 kg, the mass contributes to vibration damping and consistent parting performance in standard turning applications. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com
39mm Stechklemmhalter 5mm Cutting Width 60mm Cutting Height S32S 5C-R MGM For 5C MGM Inserts, Shaft 32mm, Length 250mm - Teknik Makina
Take advantage of a rigid holder with a 32 mm shank and a 5 mm cutting width for precise, repeatable grooving and parting operations; the 60 mm cutting height supports deeper engagement while the 250 mm overall length balances reach with rigidity. Order the K620TM grooving clamping holder via Metav Werkzeuge or consult the technical team for application advice. Grooving clamping holder K620TM — 5 mm cutting width, 32 mm shank (Teknik Makina) The Grooving clamping holder K620TM is a lathe-mounted parting and grooving tool holder engineered for secure clamping of 5C MGM indexable inserts and built for industrial turning operations Shank Ø 32 mm for stable mounting Cutting width 5 mm for narrow grooves Cutting height 60 mm for deeper engagement Compatible with 5C MGM indexable inserts Consistent clamping for repeatable parting performance The robust shank and clamping layout provide stable support during intermittent cuts, which reduces chatter and variation between cycles. With a 32 mm shank and a mass of 1.561 kg, the holder offers the rigidity required for consistent depth control and longer insert life. The S32S 5C‑R shank designation ensures compatibility with common lathe toolposts; this stability translates directly into improved process control and fewer rejected parts when machining repetitive grooves or parting components. Optimised geometry for narrow grooves and precision cuts A 5 mm cutting width paired with a 60 mm cutting height permits clean, narrow grooving and reliable parting where small kerf widths are essential. The narrow-cut configuration minimises material removal per pass, reducing cutting forces and heat generation. The holder’s geometry focuses load through the insert pocket, so the indexable insert is better supported during plunging cuts; this yields improved dimensional accuracy and a finer surface finish on the workpiece. Seamless integration with MGM clamping and Korloy inserts The clamping system is compatible with the MGM holder format and accepts 5C MGM indexable inserts from common suppliers such as Korloy, allowing easy replacement and inventory alignment across the shopfloor. The S32S 5C‑R shank and MGM interface enable straightforward mounting and exchangeability, helping maintenance teams to standardise tooling kits and reduce machine downtime for tool changes. Practical reach without compromising rigidity With an overall length of 250 mm and an outer diameter of 39 mm, the tool holder provides the reach required for off-centre grooving while maintaining sufficient stiffness for controlled cutting. This balance is particularly useful for small-batch production and mixed-series turning, where flexibility and tool life are equally important. The moderate weight supports vibration damping without imposing unnecessary load on the turret or toolpost. For expert guidance on applying the Teknik Makina K620TM grooving clamping holder in specific turning applications, contact Metav Werkzeuge for a technical consultation and delivery from our Emmerich warehouse Technical data SKU: K620TM Designation: Grooving clamping holder (Stechklemmhalter) Manufacturer: Teknik Makina Shank designation: S32S 5C-R Shank diameter: 32 mm Cutting width: 5 mm Cutting height: 60 mm Overall length: 250 mm Outer diameter: 39 mm Weight: 1.561 kg Compatible insert type: 5C MGM Compatible insert manufacturer: Korloy Holder family: MGM clamping system Application: Parting and grooving for lathe operations FAQ What insert types fit this holder? The K620TM accepts 5C MGM indexable inserts and is specified for the MGM clamping system; compatibility with Korloy 5C MGM inserts is indicated. Which shank size is required for mounting? The holder uses an S32S 5C‑R shank with a shank diameter of 32 mm, suitable for compatible lathe toolposts and turrets. How deep can this holder engage during parting operations? The design provides a cutting height of 60 mm, enabling deeper grooves and parting depths compared with shallow-height holders, while maintaining support for the insert. Is the K620TM suitable for short overhang applications? Yes — with an overall length of 250 mm and a compact outer diameter, the holder balances reach and rigidity for many turning tasks. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com
3C-R TD Groving Holder for Taegutec 3C TD inserts - Teknik Makina
Technical Data: Order Number: D720TM Item: Groving Holder usable with 3C TD Indexable Inserts of Taegutec Brand: Teknik Makina ISO Code: 2020 3C-R TD Numerical Representations: Weight: 0.398kg Total length: 125mm Additional Informattion Cutting Direction: rechts Manufacturer Teknik Makina, Nolu Sokak, No 9, Selcuklu, Turkey, eMail: info@teknik-makina.com Responsible for Europe Metav Werkzeuge GmbH, Parkring 45, 46446 Emmerich, Germany, eMail: info@metav-werkzeuge.com
40mm Clamping Holder SER 4040 R27-ER27 For 27 ER Inserts Right-Hand Cutting Interior Cooling - Teknik Makina
Combine stable 40 x 40 mm clamping geometry, a 40 mm cutting height and a secure M5x18 Torx fastening for consistent right‑hand external threading; order the clamp holder via Metav Werkzeuge or request consultant support for fitting and compatibility. Clamp holder SER 4040 – right‑hand external threading, 40 x 40 mm – Teknik Makina A heavy‑duty clamp holder engineered for right‑hand external thread turning and compatible with 27 ER indexable inserts in professional machine shops. Robust 40 x 40 mm clamping body 40 mm cutting height for deep threads Secure M5x18 Torx fastening Compatible with 27 ER indexable inserts Stable geometry for repeatable thread quality The primary advantage of this toolholder is its precise clamping geometry. The 40 x 40 mm cross section and 40 mm cutting height provide a rigid interface that reduces vibration during threading cycles, which in turn improves surface finish and dimensional repeatability. Mass distribution and the unit’s 2.589 kg weight contribute to stability on the carriage, so thread forms are produced consistently even under interrupted cuts. The ISO designation SER 4040 identifies the shank profile for straightforward integration into standard toolposts. Quick assembly and secure fixing to reduce downtime Designed for efficient workflows, the holder accepts 27 ER indexable inserts and mounts on the R27‑ER27 boring bar designation, enabling rapid insert changes without extensive reset procedures. Fixing is by an M5x18 Torx screw tightened with a T20 key, a combination that gives positive clamping force while remaining serviceable on the shop floor. The included U plate reference TA064 ensures compatibility with common mounting plates. Together, these features reduce set‑up time and make the toolholder suitable for batch production or mixed‑series turning tasks. Practical applications and operational benefits Optimised for right‑hand external threading, this holder is intended for industrial turning centres and manual lathes where reliable thread cutting is required. The robust construction supports operations in toolrooms and production lines that demand repetitive accuracy rather than one‑off setups. The overall length of 200 mm gives an accessible reach without compromising rigidity, and the toolholder is specified for right‑hand cutting direction. For purchasers, the clear technical alignment with 27 ER inserts simplifies stocking decisions and streamlines tool change procedures. Durability, compatibility and supply confidence Manufactured by Teknik Cutting Tools and distributed through Metav’s European channel, the holder benefits from tested manufacturing processes and logistical support from Emmerich. The combination of standardised ISO shank, proven fastening elements and common insert compatibility minimises the risk of mismatched components. For operations aiming to improve first‑pass yield on threaded parts, the assembly represents a pragmatic, high‑performance choice that balances ease of use with industrial robustness. For professional right‑hand external threading, contact Metav Werkzeuge for technical advice or to arrange supply of the Teknik Cutting Tools clamp holder (SKU D493TM) from our Emmerich stock Technical Data Article number: D493TM Manufacturer: Teknik Makina SKU: D493TM ECLASS: 21181004 ISO designation: SER 4040 Facts Width: 40 mm Height: 40 mm Cutting height: 40 mm Overall length: 200 mm Weight: 2.589 kg Special features Compatibility: 27 ER indexable inserts Boring bar designation: R27‑ER27 U plate reference: TA064 Torx screw: M5x18 Torx key: T20 Right‑hand cutting direction FAQ Is this holder suitable for external right‑hand thread cutting? Yes. The clamp holder (SER 4040) is specified for right‑hand external threading and is configured to accept 27 ER indexable inserts for thread‑forming and finishing operations. Which insert system fits this toolholder? The holder is compatible with 27 ER indexable inserts and is designed to mate with the R27‑ER27 boring bar interface. What fastening method secures the insert / tool to the holder? Fixing is achieved via an M5x18 Torx screw tightened with a T20 key, providing reliable clamping for machining forces encountered during threading. How does the holder improve thread quality on the lathe? The 40 x 40 mm clamping geometry and 40 mm cutting height increase rigidity and reduce vibration, leading to improved dimensional repeatability and surface finish on threaded components. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com
40mm Precision Clamping Holder SER 4040 R22-ER22 For 22 ER Inserts Right-Hand Cutting Innenkühlung - Teknik Makina
The combination of a compact 40×40 mm clamping cross-section and a 36 mm cutting height delivers consistent thread geometry and reduced set-up time; the 200 mm overall length adds reach for deeper operations. Order the holder through Metav Werkzeuge or consult the Metav team for technical guidance to ensure immediate integration into the production line. Clamping holder SER 4040 — Right‑hand external threading, 40×40 mm (Teknik Makina) The Clamping holder SER 4040 is a right‑hand tool holder for external threading, designed for use with 22 ER indexable inserts and compatible with R22‑ER22 shanks for lathe turning applications 40×40 mm clamping cross-section 200 mm overall length for extended reach Compatible with 22 ER indexable inserts Torx T15 screw M4×15 for secure clamping Accurate thread geometry through fixed cutting height The holder’s 36 mm cutting height and square 40×40 mm cross-section ensure that the insert aligns precisely with the lathe centre, reducing the need for repeated adjustments. A correct cutting height matters because it preserves the intended rake and clearance angles of the insert, which in turn improves thread profile accuracy and extends insert life. For workshops that value repeatability, this fixed geometry reduces set‑up time and minimises scrap rates, delivering measurable improvements in throughput and process stability. Robust reach and stability for demanding turning tasks With an overall length of 200 mm and a mass of 2.585 kg, the holder offers the solidity required for deeper external threading without excessive vibration. The mass and form factor contribute to improved damping during cutting, which helps maintain surface finish and prolong tool life when machining steels and similar workpiece materials. The square shank form also simplifies clamping in standard tool posts and cross‑slides, making the holder suitable for both production lathes and heavy‑duty workshop machines where stability under load is essential. Fast, secure clamping and broad compatibility Designed for use with 22 ER indexable inserts and the R22‑ER22 shank designation, the holder supports quick insert changes and precise repositioning. Retention is accomplished with a Torx T15 screw (M4×15), providing consistent clamp force and straightforward maintenance. Included component references such as TA062 for the support plate and BSP010 as a shim simplify replacement part sourcing. As a right‑hand external threading holder, it enables conventional thread cutting directions and is well suited to production environments that require reliable, repeatable external threads. For reliable external threading with secure clamping, contact Metav Werkzeuge for ordering or detailed technical advice on the Teknik Makina clamping holder SER 4040 — eMail info@metav-werkzeuge.com or call +49 2822 7131930 Technical data SKU: D507TM ISO designation: SER 4040 Manufacturer: Teknik Makina ECLASS: 21181004 Core data Clamping cross-section: 40×40 mm Cutting height: 36 mm Overall length: 200 mm Weight: 2.585 kg Cutting direction: right Special features Compatible with 22 ER indexable inserts Shank designation: R22‑ER22 Torx screw: T15 Screw size: M4×15 Support plate reference: TA062 Shim reference: BSP010 FAQ Which inserts fit the holder? The holder is designed for 22 ER indexable inserts; the geometry and clamp position match this insert standard for secure, repeatable threading. Is the holder suitable for right‑hand threading only? Yes, the tool is configured for right‑hand external threading and should be paired with inserts and lathe orientation that follow conventional right‑hand cut direction. What shank or boring bar designation is required? The holder fits shanks with the R22‑ER22 designation, ensuring correct engagement in compatible tool posts and boring bar setups. How is the insert secured and what tools are needed? Insert retention uses a Torx T15 screw (M4×15); a T15 Torx driver ensures consistent tightening and safe clamping performance. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com
40mm Stechklemmhalter KGMN KGEVR-KGMN 300 For Wendeplatten Innenkühlung Rechtsschneidend - Teknik Makina
Take advantage of stable clamping, narrow 3 mm grooving capability and a rigid 32 mm shank for consistent cycle times and predictable surface quality; order or request technical advice via Metav Werkzeuge for quick delivery and application support. Grooving clamp holder — robust parting and grooving tool holder with 3 mm cutting width (Teknik Makina) Grooving clamp holder for precision parting and grooving in turning applications, compatible with Korloy KGEVR-KGMN 300 inserts and designed for stable performance in workshop and production environments Compatible with Korloy KGEVR-KGMN 300 Shank Ø32 mm for rigid mounting Cutting width 3 mm for narrow grooves Total length 250 mm for extended reach Enhanced rigidity for predictable groove quality A focus on mechanical stability reduces chatter and improves repeatability. The holder's shank Ø32 mm provides a firm connection to the tool post, which translates into less vibration and a more consistent cutting action when machining narrow grooves. With a cutting height of 55 mm, the design ensures the insert line-up is maintained under load, delivering repeatable part geometry and lower scrap rates. This rigidity is especially relevant where short cycle times and reliable surface finish are required. Precise insert matching and straightforward integration Designed for use with the KGEVR-KGMN 300 insert family from Korloy, the clamp format accepts the standard KGMN-style plates and the holder’s interface aligns with established turning tool standards such as S32S 3C shank designation. This compatibility shortens set-up times and simplifies inventory management by allowing established inserts to be fitted without adapter changes. The result is a straightforward route to improved throughput while retaining familiar clamping practice on existing lathes. Practical dimensions and durable workshop performance With an overall total length of 250 mm and a compact cutting width of 3 mm, the holder is arranged for deep or confined grooving tasks without compromising access or control. The construction supports a serviceable life in regular production: the mass of 1.627 kg gives the assembly momentum during cutting while the geometry keeps forces in the clamping zone predictable. For operations that demand a reliable, repeatable grooving solution, this holder balances accessibility, robustness and compatibility to support efficient machining cycles. Discuss Teknik Makina grooving clamp holders with Metav Werkzeuge to match the right configuration for the application and secure timely delivery from Emmerich; email info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: K665TM Manufacturer: Teknik Makina Product: Grooving clamp holder Brand SKU: K665TM Facts Shank diameter: 32 mm Cutting height: 55 mm Cutting width: 3 mm Total length: 250 mm Weight: 1.627 kg Diameter: 40 eClass: 21181005 UID: K665TM Special features Compatible with Korloy KGEVR-KGMN 300 inserts Shank designation: S32S 3C Clamping type: KGMN-compatible Suitable for narrow grooving and parting applications FAQ What insert type fits this holder? The holder accepts KGEVR-KGMN 300 style inserts from Korloy, providing a standardised KGMN clamping interface for secure seating and repeatable cutting performance. Which shank size is required for mounting? Mounting is designed for a 32 mm shank interface (S32S 3C), ensuring a rigid connection for turning and grooving operations. Is the holder suitable for deep grooves? Yes — with a total length of 250 mm and a compact cutting width of 3 mm, the design is geared towards access in deeper grooves while maintaining control over cutting forces. What are the key benefits for production use? The holder offers improved stability through a Ø32 mm shank and predictable clamping for KGMN inserts, which helps reduce cycle variability and rework in serial machining. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com
40mm Stechklemmhalter KGMN, For KGEVR-KGMN 400 Wendeplatten, Innenkühlung, Rechtsschneidend, S32S 4C - Teknik Makina
Take advantage of a sturdy parting solution that combines stable clamping, precise cutting geometry and standardised insert compatibility to reduce setup time and improve cycle consistency; order directly via Metav Werkzeuge or ask the consultants for tailored integration advice. Stechklemmhalter K668TM — Parting tool holder with 32 mm shank and 55 mm cutting height (Teknik Makina) The Stechklemmhalter is a purpose-built parting tool holder for indexable grooving inserts, engineered for lathe-based parting and grooving operations where repeatable cut control and easy insert replacement are required. 32 mm shank diameter for stable clamping 55 mm cutting height for deep grooving Compatible with Korloy KGEVR-KGMN 400 inserts 250 mm overall length for extended reach Stable clamping for accurate, repeatable parting A robust toolholder backbone is essential when consistent parting quality is required across batches. The parting tool holder features a 32 mm shank, providing a solid contact surface in the tool post and reducing micro-movement during cut engagement. With a 55 mm cutting height and a 4 mm cutting width, the holder is dimensioned to support standard grooving depths while maintaining rigidity and thermal stability. The result is improved repeatability between operations, fewer scrap parts and a reduction in rework cycles — a direct contribution to process efficiency. Fast changeover through standard insert compatibility Minimising machine downtime is achieved by using established insert formats and secure clamping. This holder accepts Korloy KGEVR-KGMN 400 indexable inserts and matches common bore and clamp standards such as S32S 4C and the KGMN bar designation. Compatibility with these widely used components simplifies stock management and shortens changeover procedures. The standardized interface enables quick, reliable insert seating and torque-controlled clamping, which is beneficial for workshops aiming to increase machine uptime and throughput. Designed to withstand workshop demands Long tool reach and a balanced mass distribution matter when access and vibration control are priorities. With a 250 mm overall length and a mass of 1.623 kg, the holder delivers the reach necessary for deeper parting operations while preserving stability under feed forces. The geometry has been developed to reduce chatter and to support consistent chip flow, which extends insert life and lowers tooling costs per component. The construction is tailored to provide dependable service in job shops and production environments where robustness and low maintenance are prized. Where this holder excels in production The holder is particularly suited to turning centres and manual lathes performing precision parting or grooving on standard workpiece diameters; the 40 mm diameter reference and the bar-compatible shank make it applicable for setups requiring moderate reach and a secure clamping interface. Applications include component cut-off, internal and external grooving where a controlled slot width and depth are critical. The combination of a standard insert family and a rigid mounting profile supports repeatable results and straightforward process validation in small to medium production runs. For reliable parting performance from Teknik Makina, contact Metav Werkzeuge for specification checks, order placement and implementation support — email info@metav-werkzeuge.com or call +49 2822 7131930 to discuss how the K668TM can be integrated into current turning processes. Technical data Article number: K668TM Name: Stechklemmhalter Manufacturer: Teknik Makina Compatible insert manufacturer: Korloy Compatible inserts: KGEVR-KGMN 400 Facts Shank diameter: 32 mm Cutting height: 55 mm Cutting width: 4 mm Overall length: 250 mm Reference diameter: 40 Weight: 1.623 kg eClass: 21181005 Special features Bore/bar designation: S32S 4C Holder bar designation: KGMN Suitable for indexable grooving/parting inserts Designed for lathe parting and grooving applications FAQ What insert type fits the holder? The holder is compatible with Korloy KGEVR-KGMN 400 indexable inserts; the clamping geometry is matched to that insert family for secure seating and repeatable positioning. Which shank diameter is required for mounting? The toolholder requires a 32 mm shank seat in the tool post and is designed to deliver stable clamping for parting operations. What cutting height and width does the holder support? The design provides a 55 mm cutting height and supports a 4 mm cutting width, suitable for standard grooving and parting tasks. Is the holder suitable for long-reach operations? With a 250 mm overall length, the holder offers extended reach suitable for many lathe set-ups where deeper access is necessary while maintaining rigidity. Which machine applications is the holder intended for? The toolholder is intended for lathe-based parting and grooving operations in job shops and production environments where indexable inserts are preferred for fast changeover and cost control. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com
41mm Cut-Off Tool Holder S32S 3mm Cutting Width, 50mm Cut Height, S229 3C-R - Teknik Makina
Take advantage of robust clamping, precise 3 mm parting capability and a stable 32 mm shank for consistent cycle times; order directly through Metav Werkzeuge or consult our specialists for application advice. Stechklemmhalter K626TM — Parting tool holder with 32 mm shank and 50 mm cutting height by Teknik Makina Stechklemmhalter K626TM is designed as a compact, high-stability parting tool holder for standard turning centres, enabling controlled chip separation and repeatable grooving operations. 32 mm shank for stable mounting 50 mm cutting height for deep operations Accepts 3C indexable inserts 3 mm cutting width for precise parting Stable mounting for reliable parting cycles A solid mounting interface is decisive for predictable parting results. The holder features a 32 mm shank and an overall length of 250 mm, creating a rigid connection to the tool post and reducing vibration during cut-off operations. The combination of shaft dimensions and mass (1.56 kg) improves parting accuracy and surface finish, while the substantial 50 mm cutting height provides clearance and tool projection options for deeper cuts. In practice, a stable toolholder reduces scrap rates and machine downtime by keeping the insert engagement consistent throughout each cycle. Fast insert changes and reduced machine downtime Clamping design and insert compatibility determine shop-floor efficiency. This tool accepts 3C indexable inserts and is matched to a clamping unit 3C-R S229, allowing secure clamping with minimal adjustment time. The 3 mm cutting width supports narrow parting and grooving tasks where material waste is minimised and cutting forces are concentrated. Rapid insert replacement and clear geometric references mean less time at the machine and quicker return to full production, which directly improves throughput and lowers per-part machining costs. Designed for predictable results in everyday turning Integration with standard bar designations (bar: S32S) simplifies tool selection and replacement across multiple lathes. The holder’s geometry and clamping principle are intended for consistent chip control and repeatable set-up: once configured, repeatability is ensured by the mechanical interfaces rather than by trial adjustments. For engineers and workshop managers, this means a reliable base for process documentation and quality assurance—beneficial when establishing machining parameters, SPC checks or when training personnel on stable parting routines. Contact Metav Werkzeuge for application guidance and to secure the Teknik Makina parting tool holder K626TM; expert advice and ordering assistance are available via info@metav-werkzeuge.com or by phone on +49 2822 7131930 Technical data Article number: K626TM Manufacturer: Teknik Makina Designation: Stechklemmhalter Manufacturer sku: K626TM Core data Shank diameter: 32 mm Cutting height: 50 mm Cutting width: 3 mm Overall length: 250 mm Diameter: 41 mm Weight: 1.56 kg Special features For indexable inserts: 3C Clamping designation: 3C-R S229 Bar designation ISO: S32S Suitable for parting and grooving operations FAQ What insert type does this holder accept? The Stechklemmhalter K626TM accepts 3C indexable inserts, secured with the compatible clamping unit 3C-R S229 for reliable seating. Which shank diameter is required for installation? The holder is manufactured with a 32 mm shank, matching standard tool-post mounts for secure installation and reduced vibration. How deep can the holder support cutting operations? With a 50 mm cutting height the holder is suitable for moderate-depth parting and grooving tasks while maintaining rigidity. Is this holder suitable for narrow parting applications? Yes, the 3 mm cutting width supports narrow parting widths where controlled chip evacuation and minimal material loss are required. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com
42mm Stech Tool Holder S32S 4C-R S224, For 4C Indexable Inserts, Internal Cooling, Right-Hand Cutting - Teknik Makina
Optimise parting and grooving operations with the robust 32 mm shank and 50 mm cutting height for stable cuts and consistent insert life; the precise 4 mm cutting width enables narrow slotting where repeatability matters. Order the tool directly via Metav Werkzeuge or consult our specialists for application guidance. Stechklemmhalter — parting and grooving toolholder, 32 mm shank, 50 mm cutting height (Teknik Makina) The Stechklemmhalter is a parting and grooving toolholder engineered for medium-duty turning and slotting tasks, compatible with 4C indexable inserts and designed for reliable performance in workshop and production environments. Accepts 4C indexable inserts 32 mm shank diameter for high rigidity 50 mm cutting height for deeper grooves 4 mm cutting width for narrow slotting Stable clamping for consistent cycle times The holder’s 32 mm shank and robust geometry are designed to reduce vibration, so cutting conditions are stabilised and insert life is extended. Integrated clamping details, specified as 4C-R S224, ensure that 4C indexable inserts are secured with repeatable positioning, which leads to fewer re-clamps and less downtime. For machinists focused on predictable output, the combination of shaft rigidity and an accurately defined cutting height contributes directly to improved surface finish and reduced scrap rates. Easy integration with standard turning setups With the S32S shank designation and an overall length of 250 mm, the toolholder is intended for seamless installation in common tool posts and turret systems. The compact head diameter (Ø 42 mm) and a net weight of 1.672 kg strike a balance between mass for damping and a form factor that fits tight tooling envelopes. Provided dimensions and designations allow engineers to verify compatibility quickly; where spindle clearance or overhang are constrained, the listed measures support confident process planning. Practical benefits for production and maintenance The 4 mm cutting width and 50 mm cutting height allow controlled material removal when producing narrow slots or parting off small-diameter workpieces. Because the system uses standard 4C inserts, replacement tooling and inventory management are simplified and cost-effective. Routine maintenance is straightforward: insert changes follow established indexable-insert procedures, and the clamping designation facilitates finding matching spare parts. For facilities seeking a reliable, easily serviced solution, this holder offers a pragmatic mix of performance and maintainability. For precise parting and grooving needs, contact Metav Werkzeuge to request application advice or to procure Teknik Cutting Tools’ parting and grooving solution K656TM; reach our specialists at info@metav-werkzeuge.com or by phone on +49 2822 7131930 Technical data Article number: K656TM Designation: Stechklemmhalter Manufacturer: Teknik Makina Weight: 1.672 kg Overall length: 250 mm Facts Shank diameter: 32 mm Head diameter: 42 mm Cutting height: 50 mm Cutting width: 4 mm Compatible inserts: 4C Special features Shank designation: S32S Clamping designation: 4C-R S224 Accepts 4C indexable inserts FAQ What inserts does the parting and grooving toolholder use? The toolholder accepts 4C indexable inserts, allowing straightforward replacement and established stocking practices for common insert geometries. Is the holder suitable for heavy overhangs in small lathes? The K656TM is designed with a 32 mm shank and a 250 mm overall length; mounting with minimal overhang is recommended to preserve rigidity and do not compromise finish. How does the shank designation affect compatibility? The S32S shank designation identifies the nominal shank interface and helps confirm the holder will fit standard tool posts and turret bores matching that specification. What typical applications suit this clamping holder? The holder is intended for parting and narrow grooving tasks in turning operations where a 4 mm cutting width and repeatable positioning are required. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
42mm Stechklemmhalter 4C For Indexable Inserts S32S 4C-R S229 Innenkühlung Rechtsschneidend - Teknik Makina
Take advantage of the combination of stable clamping, compatibility with 4C indexable inserts and robust dimensions for consistent grooving results; order via Metav Werkzeuge or consult our specialists for application support. Grooving clamp holder K632TM — 32 mm shank, for 4C indexable inserts (Teknik Makina) The Grooving clamp holder K632TM is designed for precision grooving and turning operations on CNC lathes, compatible with 4C indexable inserts and optimised for stable, vibration‑reduced cutting. 32 mm shank for stable clamping Compatible with 4C indexable inserts 4 mm maximum cutting width 50 mm cutting height, 250 mm overall length Consistent clamp stability for repeatable grooves The K632TM combines a 32 mm shank with a compact, rigid body to deliver consistent clamping in serial production and single‑piece machining. The solid shank diameter contributes to reduced chatter, which is beneficial for surface finish and can extend insert life through lower vibration and heat generation. Where tight tolerances are required, the design enables reliable repeatability so that setup times are shortened and process variability is minimised. The shank designation S32S confirms compatibility with common tool posts and holders used on industrial lathes. Precision grooving with industry-standard inserts Configured for 4C indexable inserts, the holder accepts the established 4C insert geometry to simplify insert sourcing and changeover. The clamping bar designation 4C‑R S229 provides a clear reference for selecting compatible inserts and spare clamping components. With a 4 mm cutting width and a 50 mm cutting height, the tool is suited to narrow grooving and parting tasks where controlled chip formation and secure insert seating are required. The clamping mechanism is designed so that insert replacement is straightforward, helping to reduce machine downtime during routine maintenance. Robust dimensions built for workshop reliability With a 250 mm overall length and an outer diameter of 42 mm, this grooving holder balances reach with torsional stiffness, making it suitable for a wide range of turning setups. The holder’s mass of 1.656 kg contributes to damping of cutting forces while remaining manageable for tool changes and fixture handling. These dimensions make the component appropriate for medium‑to‑heavy turning operations in general workshop and production environments, where a dependable toolholder supports consistent cycle times and predictable quality. Practical application guidance and workshop benefits Designed for use in CNC lathe grooving and parting operations, the holder is particularly appropriate where indexable inserts are preferred for cost‑efficient production. When mounted correctly and paired with suitable inserts, the holder supports precise groove profiles and repeatable part geometry. For further technical clarification — such as recommended insert grades for specific workpiece materials or optimal clamping torque — Metav Werkzeuge’s technical team can provide guidance based on shop practice and material demands. Metav’s role as a quality filter in Emmerich ensures reliable supply and documentation that supports integration into production processes. For application advice or to request the Teknik Cutting Tools grooving clamp holder K632TM for a specific machining setup, contact Metav Werkzeuge in Emmerich by e‑mail at info@metav-werkzeuge.com or by phone on +49 2822 7131930 to discuss delivery, compatibility and next‑step recommendations. Technical Data SKU: K632TM Manufacturer: Teknik Makina Facts Shank diameter: 32 mm Cutting height: 50 mm Cutting width: 4 mm Weight: 1.656 kg Diameter: 42 mm Overall length: 250 mm Special features Compatible with 4C indexable inserts Shank designation: S32S Clamping bar designation: 4C‑R S229 Suitable for precision grooving and parting FAQ What insert type does the holder accept? The holder is compatible with 4C indexable inserts; reference clamping bar designation 4C‑R S229 for matched components. Which shank diameter is specified for this tool holder? The tool holder features a 32 mm shank (S32S) for stable mounting in standard tool posts. What are the primary dimensions relevant to setup? Relevant dimensions are 4 mm cutting width, 50 mm cutting height, 250 mm overall length and 42 mm outer diameter. Is the grooving holder suitable for heavy‑duty turning? The combination of mass (1.656 kg) and robust shank provides good rigidity for medium to heavy turning and grooving tasks when used within machine and insert limits. How does this holder help with production consistency? The robust shank and secure clamping reduce vibration and improve repeatability, which supports consistent groove geometry and longer insert life. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com
47 Stechklemmhalter 4mm Cutting Width, S40T 4C-R Shaft 40mm, 60mm Cutting Height, For 4C MGM Inserts, MGM Shank, Weight 2.942kg, Total Length 300mm - Teknik Makina
Take advantage of the combination of precise clamping, stable 40 mm shank and compatibility with Korloy 4C MGM inserts to maintain consistent groove quality in series production. Order the grooving clamping holder directly via Metav Werkzeuge or ask the technical consultants for application-specific advice. Stechklemmhalter K616TM – Grooving clamping holder with 4 mm cutting width (Teknik Makina) The Stechklemmhalter is a robust grooving clamping holder for CNC turning applications, designed to accept 4C MGM inserts and to provide rigid support for precision parting and grooving operations. Solid 40 mm shank for stable clamping Compatible with Korloy 4C MGM inserts Cutting width 4 mm for precise grooving Overall length 300 mm for deep turning operations Maximum stability for repeatable grooves and reduced vibration The holder is engineered around a 40 mm shank and a substantial Ø47 mm body, which together increase stiffness at the tool tip and reduce chatter under load. This rigidity translates into consistent groove geometry and predictable tool life when machining repeat batches. The design also contributes to safer set‑up on CNC lathes, as the mass distribution and the weight of 2.942 kg damp vibrations that would otherwise affect surface finish. For manufacturers seeking measurable improvements in process stability, the combination of shank diameter and overall mass offers a clear productivity advantage. Fast insert mounting and proven insert compatibility to cut set‑up time Fitted for the MGM clamping system and the ISO bar designation S40T 4C‑R, the holder accepts Korloy 4C MGM inserts, enabling quick replacement and secure clamping without additional adaptors. The 4 mm cutting width and 60 mm cutting height are optimised for narrow grooving and parting tasks, allowing accurate control of chip formation and groove dimensions. The straightforward interface between holder and insert reduces set‑up time and limits the need for repeated adjustments, which supports higher uptime and a faster route to production readiness. Built for deeper turning tasks while maintaining precision With an overall length of 300 mm, the tool is suitable for operations that require reach beyond short overhangs, while the geometry of the clamping block keeps the cutting edge firmly located. The bar designation S40T 4C‑R indicates a standardised shank form for integration into existing toolposts and turret systems, simplifying implementation on the shop floor. The holder’s balance of length and stiffness helps to preserve dimensional accuracy in groove depth and wall straightness, making it a reliable choice for both repeat manufacturing and prototyping runs where groove integrity matters. Contact Metav Werkzeuge for a tailored recommendation on Teknik Cutting Tools' grooving clamping holder K616TM — technical advice and order support available at info@metav-werkzeuge.com or by phone on +49 2822 7131930 Technical data Article number: K616TM Manufacturer: Teknik Makina Product: Stechklemmhalter Compatible inserts: Korloy 4C MGM Facts Shaft diameter: 40 mm Overall length: 300 mm Body diameter: 47 mm Cutting width: 4 mm Cutting height: 60 mm Weight: 2.942 kg Special features ISO designation: S40T 4C-R Clamping type: MGM Designed for grooving and parting applications Ready for use in CNC turning setups FAQ Which inserts fit this grooving clamping holder? The Stechklemmhalter K616TM accepts Korloy 4C MGM inserts via the MGM clamping system, ensuring secure seating and rapid index changes. What are the key dimensional features to check before ordering? Check the 40 mm shank diameter, 300 mm overall length and 4 mm cutting width to confirm compatibility with the lathe turret and the required groove dimensions. Is the holder suitable for extended overhangs? The 300 mm overall length provides extended reach for deeper turning operations while the substantial body diameter and mass help preserve stability and groove accuracy. How does the S40T 4C‑R designation affect mounting? The S40T 4C‑R designation denotes a standardised shank and bar form that aligns with common toolpost and turret interfaces, simplifying mechanical integration on compatible machines. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com
47mm Stech Grooving Tool Holder 5mm Cut Width, S40T 5C-R MGM, 60mm Cutting Height, 300mm Overall Length - Teknik Makina
Combine robust clamping with a stable 40 mm shank and a precise 5 mm cutting width to ensure reliable parting and grooving operations; order this clamping parting toolholder via Metav Werkzeuge or consult the specialists for integration advice. Stechklemmhalter K622TM – Clamping parting toolholder with 40 mm shank and 5 mm cutting width (Teknik Makina) A Stechklemmhalter engineered for secure parting and grooving on lathes, compatible with Korloy 5C MGM indexable inserts and designed for straightforward integration into existing tool setups 40 mm shank for secure lathe clamping 5 mm cutting width for narrow parting cuts 60 mm cutting height for deep grooves Compatible with Korloy 5C MGM inserts Stable clamping for repeatable parting performance The holder is built around a robust 40 mm shank, which provides a solid interface with standard turret and toolpost fixtures. The shank designation S40T 5C-R describes the adopted mounting form and ensures consistent datum location when exchanged between stations. With a mass of 2.936 kg, the assembly dampens vibration during cut-off operations and helps to maintain tool position under load. This mechanical stability translates directly into tighter tolerances and extended insert life in high-repeat production runs. Narrow & deep cuts with predictable chip control Designed for narrow parting cuts, the 5 mm cutting width delivers accurate, material-efficient grooves while the 60 mm cutting height allows deeper engagements where required. The combination of these dimensions supports effective chip formation and evacuation when paired with compatible indexable tips. The toolholder’s 300 mm overall length and 47 mm diameter balance reach and rigidity, making it suitable for both short-run and batch turning where precise cross-section control is needed. Seamless compatibility and workshop efficiency Compatibility with Korloy 5C MGM indexable inserts and an MGM-style clamp simplifies insert procurement and changeover routines. The holder is identified by SKU K622TM and is sparingly designed to match common MGM clamping systems, so replacement inserts and clamp hardware from established suppliers fit without modification. This compatibility reduces machine downtime and supports lean tooling practices in metalworking and subcontract turning operations. Contact Metav Werkzeuge today for tailored tooling advice on this Teknik Makina clamping parting toolholder (SKU K622TM) and to arrange prompt supply from Emmerich for immediate workshop use Technical data Article number: K622TM Manufacturer: Teknik Makina Dimensions & weight Shank diameter: 40 mm Cutting width: 5 mm Cutting height: 60 mm Overall length: 300 mm Diameter: 47 mm Weight: 2.936 kg Compatibility & features Compatible with Korloy 5C MGM inserts Clamping type: MGM Shank designation: S40T 5C-R SKU: K622TM FAQ What lathe fittings are required for this toolholder? The Stechklemmhalter K622TM is specified with a 40 mm shank and S40T 5C-R designation; it is intended for turrets and toolposts that accept a 40 mm cylindrical shank. Which indexable inserts fit this holder? This clamping parting toolholder is compatible with Korloy 5C MGM indexable inserts; the MGM clamping form is supported to allow immediate use with standard Korloy tips. Is the holder suitable for deep-parting operations? With a 60 mm cutting height and a rigid 40 mm shank, the holder is designed to manage deeper groove and parting operations while maintaining stability. What is the overall length and how does that affect setup? The overall length is 300 mm, providing reach for various turning setups while preserving rigidity for consistent cutting conditions. Which SKU should be referenced when ordering or requesting technical data? Reference K622TM when enquiring about this Teknik Makina clamping parting toolholder to ensure correct identification. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com
48mm Stechklemmhalter S40T 3C-R MGM For 3C MGM Inserts, Innenkühlung, Schneidenhöhe 60mm - Teknik Makina
Take advantage of precise parting performance and robust clamping: the holder’s 3 mm cutting width and 60 mm cutting height deliver repeatable grooves while the 40 mm shank diameter ensures stable mounting in heavy‑duty setups; order the tool directly via Metav Werkzeuge or consult the team for application advice. Clamping parting tool holder K609TM by Teknik Makina — 3 mm cutting width, 60 mm cutting height A robust clamping parting tool holder designed for industrial grooving and parting operations, compatible with Korloy 3C MGM indexable inserts and built for stable performance in CNC turning applications. 3 mm cutting width for precise parting 60 mm cutting height for deep grooves 40 mm shank diameter for stable clamping Compatible with 3C MGM indexable inserts Consistent, precise parting for repeatable results The holder’s 3 mm cutting width paired with a 60 mm cutting height provides a focused cutting geometry for controlled chip formation and minimal side play. This combination reduces rework by keeping the cut profile consistent across batches. Compatibility with indexable inserts means cutting edges can be renewed without regrinding the body, which shortens machine downtime and supports predictable cycle times. For users seeking measurable improvements in process reliability, this tool body gives a clear engineering advantage. Stable mounting for reduced vibration and longer tool life A 40 mm shank diameter and a substantial mass (approx. 2.94 kg) increase rigidity at the toolholder–spindle interface, lowering chatter and improving surface finish during parting operations. The holder’s geometry and clamping concept are engineered to secure the insert firmly, translating into steadier cutting forces and extended insert life. Operators will find setup tolerances easier to maintain when body stiffness reduces deflection under load, a pragmatic gain in production environments that require repeatable accuracy. Straightforward integration with existing tool setups With an overall length of 300 mm and a body diameter of 48 mm, this holder fits common lathe tool posts and modular tool systems used in series production. The shank designation S40T 3C‑R and the MGM clamping interface facilitate quick identification and interchange with matching carriers and accessories. Because the unit accepts 3C MGM style inserts and is listed as compatible with Korloy insert specifications, it aligns with widely available insert grades to suit varied materials and cutting conditions, simplifying procurement and inventory management. Built for workshop and industrial use Manufactured by Teknik Makina, the K609TM is intended for repetitive parting and grooving tasks where secure clamping and dimensional stability matter. Its compact cutting width combined with substantial cut height allows concentrated operations on slender workpieces as well as deeper groove machining. The design supports production workflows that value uptime and consistent tolerances, making the holder a reliable component in both contract workshops and in‑house production lines. For procurement and technical queries regarding the Teknik Makina K609TM clamping parting tool holder, contact Metav Werkzeuge in Emmerich — call +49 2822 7131930 or email info@metav-werkzeuge.com to discuss compatibility with specific inserts and machine tool setups. Technical data Article number: K609TM Manufacturer: Teknik Makina Facts Overall length: 300 mm Weight: 2.94 kg Shank diameter: 40 mm Cutting width: 3 mm Cutting height: 60 mm Body diameter: 48 mm Special features Compatible inserts: 3C MGM Suitable insert supplier: Korloy Shank designation: S40T 3C‑R Application: parting / grooving FAQ What inserts fit this clamping parting tool holder? The holder accepts 3C MGM style indexable inserts; it is specified as compatible with Korloy inserts and the MGM clamping interface. Is the tool suitable for heavy‑duty parting on larger diameters? The K609TM’s 40 mm shank diameter and robust body mass support stable parting operations; suitability for a specific workpiece diameter depends on machine rigidity and the chosen insert grade. How does the shank designation S40T 3C‑R affect compatibility? S40T 3C‑R describes the shank and mounting form; matching tool posts and carriers that accept S40T shanks will accommodate the holder without modification. Can the clamping concept reduce insert runout and improve finish? The clamping design for MGM inserts secures the cutting edge precisely, which helps to reduce runout and contributes to a more consistent surface finish under correct setup conditions. What dimensions are most relevant when planning a retrofit into an existing tool turret? Key dimensions are the 40 mm shank diameter, 300 mm overall length, and 48 mm body diameter to ensure the holder fits the turret envelope and maintains clearance during parting. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com
49mm Stech Boring Holder 50mm Cut Height 4mm Cutting Width S40T, 4C For Indexable Inserts, Internal Cooling, Right-Hand Cutting - Teknik Makina
Compact, rigid and designed for repeatable grooving, the Teknik Makina parting and grooving clamp holder combines a 40 mm shank with a 50 mm cutting height to deliver stable, accurate operations; benefit from the secure clamping for 4C indexable inserts and order directly via Metav Werkzeuge or request application advice from our consultants. Parting and Grooving Clamp Holder — 40 mm shank, 50 mm cutting height (Teknik Makina) A parting and grooving clamp holder for secure clamping of 4C indexable inserts in turning and CNC grooving applications. Secure clamping for 4C indexable inserts 40 mm shank for heavy-duty stability 50 mm cutting height for deep grooves Compatible with S40T shank designation Maximised rigidity for repeatable cuts The holder is built to reduce vibration and maintain cutting stability: its 40 mm shank combined with a 300 mm overall length and a substantial mass (3.113 kg) creates a rigid tool assembly that improves surface finish and tool life. In practice, increased mass and the robust shank dimension lower deflection during parting and grooving, which leads to more consistent dimensional results. For CNC and manual lathes where groove accuracy is critical, this rigidity translates into fewer rework cycles and predictable cycle times. Fast, secure insert clamping with clear geometry Designed for 4C indexable inserts, the clamp arrangement identified as 4C-R S229 provides repeatable seating and easy replacement. The holder accepts a 4 mm cutting width and a 50 mm cutting height, making it suitable for medium-depth grooving tasks. The S40T shank designation indicates the recommended tool shank standard, simplifying integration into existing tool posts or turret stations. For users unfamiliar with insert systems: indexable inserts are replaceable cutting edges that locate precisely in a pocket; secure clamping ensures the insert remains seated under cutting forces and that positioning repeatability is maintained between changes. Workshop compatibility and operational benefits Integration is straightforward: the holder’s 49 mm diameter and standard shank interface make it compatible with common grooving fixtures and turrets, while the 4C insert family is widely available across suppliers. The result is a practical combination of accessibility and performance that supports both small-batch shops and production lines. Beyond compatibility, the configuration reduces set-up time; clearer insert indexing and a reliable clamp reduce downtime during tool changes, supporting steady production flow and lower overall operating costs. Where process optimisation is sought, this configuration offers a pragmatic path to improved throughput. For procurement or technical consultation regarding the Teknik Makina parting and grooving clamp holder (SKU K634TM), contact Metav Werkzeuge for tailored advice and order placement via info@metav-werkzeuge.com or +49 2822 7131930 Technical data Article number: K634TM Name: Parting and grooving clamp holder Manufacturer: Teknik Makina Facts Shank diameter: 40 mm Cutting height: 50 mm Cutting width: 4 mm Overall length: 300 mm Diameter: 49 mm Weight: 3.113 kg Suitable for inserts: 4C Shank designation: S40T Clamp holder designation: 4C-R S229 Special features Compatibility with 4C indexable inserts Rigid clamping design Standard S40T shank interface Suitable for turning and CNC grooving operations FAQ What insert type fits this holder? The holder is configured for 4C indexable inserts; the clamp model is specified as 4C-R S229 to ensure correct seating and repeatability. Which shank standard is required? This tool uses an S40T shank designation and a 40 mm shank diameter, designed for turrets and tool posts that accept that standard. What are the key dimensions to check before fitting? Relevant dimensions are overall length 300 mm, diameter 49 mm, cutting height 50 mm and cutting width 4 mm; these determine clearance and depth capabilities. Is the holder suitable for production grooving operations? Yes, the holder’s rigidity (mass 3.113 kg and 40 mm shank) and standard insert compatibility make it suitable for repeatable production grooving and parting tasks. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com
49mm Stechklemmhalter 3mm Cutting Width, 50mm Cutting Height, S40T Shank, 3C For Wendeplatten, 40mm Shaft Diameter, 300mm Overall Length - Teknik Makina
Take advantage of the holder’s combination of robust clamping and precise groove control — a 40 mm shank and 3 mm cutting width enable stable, repeatable grooving operations; the 50 mm cutting height and 300 mm overall length provide reach and engagement for longer workpieces. Order or request technical advice via Metav Werkzeuge for reliable delivery and application support. Stechklemmhalter — Grooving clamp holder with 40 mm shank and 3 mm cutting width (Teknik Makina) The Stechklemmhalter is a grooving clamp holder engineered for precision parting and narrow-groove turning, suitable for indexable 3C inserts and designed to deliver stable clamping and consistent chip control in shop-floor and production environments. Robust 40 mm shank for stable clamping 3 mm cutting width for narrow grooves 50 mm cutting height for deep engagement 300 mm overall length for extended reach Stable machining through a high-diameter shank A substantial 40 mm shank gives the holder exceptional torsional stability, which reduces vibration during grooving and parting tasks and therefore improves surface quality. The increased rigidity translates directly into consistent tool life for the insert and fewer reworks, so cycle times remain predictable. For operations where repeatability matters, the combination of shank diameter and robust clamping design supports stable cutting conditions even under intermittent or heavy engagement. Precise groove control with narrow cutting width The holder’s 3 mm cutting width is tailored for narrow-groove and parting work, enabling accurate slotting while keeping material removal localised. With a 50 mm cutting height, the tool supports deeper engagement when a single, secure setup is preferred over multiple passes. The geometry and indexing for 3C inserts allow straightforward insert seating and secure clamping, which simplifies tool setup and reduces downtime during insert changes. Reach and accessibility for longer components An overall length of 300 mm extends reach for workpieces with limited access or for setups requiring the tool to clear fixtures and chucks. The holder’s diameter at the cutting head and the overall balance deliver confident axial stiffness at reach, maintaining cutting stability. This makes the tool suitable for batch and one-off production where accessibility and precise positioning are necessary without compromising finish or dimensional control. Compatibility, handling and workshop integration Designed for use with 3C indexable inserts and specified shank designations (S40T / 3C-R S229), the holder integrates smoothly into existing tool setups. The moderate mass of 2.594 kg contributes to a grounded feel during mounting while remaining manageable for ordinary toolchanges. Routine maintenance is limited to secure clamping checks and insert seat cleaning; the simple mechanical design keeps service intervals short and predictable, supporting continuous operation in a busy turning department. For dependable grooving performance with Teknik Makina equipment, contact Metav Werkzeuge in Emmerich for personalised advice and procurement support Technical data Article number: K628TM Manufacturer: Teknik Makina Product: Stechklemmhalter (grooving clamp holder) For indexable inserts: 3C Shank designation: S40T Holder designation: 3C-R S229 Core measurements Shank diameter: 40 mm Overall length: 300 mm Cutting height: 50 mm Cutting width: 3 mm Diameter (head): 49 mm Weight: 2.594 kg Compatibility & features For indexable inserts type 3C Suitable for grooving and parting operations Stable clamping design for reduced vibration Designated for S40T shank systems FAQ What insert type is required for this holder? The holder is designed for 3C indexable inserts and seats inserts compatible with the 3C geometry. Which shank size fits the holder? The holder is specified for a 40 mm shank (S40T) and is supplied with the matching shank designation 3C-R S229. Is the holder suitable for deep grooving? Yes, with a cutting height of 50 mm the holder supports deeper single-pass engagements where the process and machine rigidity allow. How long is the holder and why does that matter? The overall length is 300 mm, which improves reach for workpieces with restricted access while maintaining axial stiffness for consistent cuts. What is the SKU and manufacturer of the holder? The item is listed as SKU K628TM and manufactured by Teknik Makina Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com
5C-R MGM Groving Holder for Korloy 5C MGM inserts - Teknik Makina
Specifications: Order Number: D684TM Item: Groving Holder usable with 5C MGM Indexable Inserts of Korloy Brand: Teknik Makina ISO Code: 3232 5C-R MGM Quantitative Characteristics: Weight: 1.268kg Total length: 150mm Additional Informattion Cutting Direction: rechts Manufacturer Teknik Makina, Nolu Sokak, No 9, Selcuklu, Turkey, eMail: info@teknik-makina.com Responsible for Europe Metav Werkzeuge GmbH, Parkring 45, 46446 Emmerich, Germany, eMail: info@metav-werkzeuge.com
60 Stechklemmhalter 3° 2525 3C-L (60-80) for MGM 3 Innenkühlung Linksschneidend - Teknik Makina
Take advantage of a robust combination of precise clamping geometry, compatibility with Korloy MGM 3 inserts and a compact 150 mm overall length for efficient left-hand parting operations; order the parting tool holder directly via Metav Werkzeuge or ask our consultants for application advice. Teknik Makina parting clamp holder — left-hand, ISO 2525, for Korloy MGM 3 inserts Parting clamp holder for left-hand cut-off and grooving applications in turning processes, designed for use with Korloy MGM 3 inserts and ISO 2525 shank systems. Left-hand cutting direction compatible Fits Korloy MGM 3 indexable inserts 25 mm cutting head width for stability Max cutting diameter Ø80 mm supported Stable clamping for reliable parting results A compact clamp holder constructed to deliver consistent clamping force and repeatable parting cycles. The combination of a 25 mm cutting head and an ISO 2525 shank provides a stable interface between machine and tool, reducing chatter and extending insert life. This rigidity translates into measurable process benefits: fewer interrupted cycles, improved surface finish and less insert wear when machining non-critical steels and general workshop materials. The product is supplied in a compact format weighing 0.717 kg, which simplifies handling and tool change procedures on busy machining centres. Designed for efficient insert usage and quick set-up The holder accepts Korloy MGM 3 indexable inserts and is optimised for a 3 mm cutting width, allowing precise parting with minimal material loss. The design supports a maximum cutting depth of 17 mm for the parting blade, while the shaft cutting length of 25 mm gives adequate engagement for most facing and grooving set-ups. Clear, industry-standard labelling such as the ISO 2525 designation and compatibility note for 3C-L (60–80) bar sizes helps planning and inventory management, speeding up tooling selection and reducing set-up time at the lathe. Compact overall length with practical machining capacity With an overall length of 150 mm and a supported maximum machining diameter of Ø80 mm, the holder is well suited to confined toolposts and smaller lathes where space is at a premium. The 40 mm cutting height ensures correct insert support, improving chip control and operator confidence during repetitive cut-off tasks. The left-hand cutting orientation is particularly useful for specific machine arrangements and workpiece feed directions, enabling the holder to be integrated seamlessly into established turning programmes. For tailored advice on using this Teknik Makina parting clamp holder (SKU D802TM) with Korloy MGM 3 inserts and to arrange supply via Metav Werkzeuge in Emmerich — email info@metav-werkzeuge.com or call +49 2822 7131930 for prompt technical guidance and order placement Technical data Article number: D802TM Manufacturer: Teknik Makina Facts Cutting head width: 25 mm Cutting width: 3 mm Cutting height: 40 mm Maximum cutting diameter: Ø80 mm Stech depth (max): 17 mm Shaft cutting length: 25 mm Overall length: 150 mm Weight: 0.717 kg Shank designation: ISO 2525 Versions / Special features Left-hand cutting direction Compatible with Korloy MGM 3 inserts Bar compatibility: 3C-L (60–80) Suitable for parting and grooving applications Compact design for restricted toolpost space FAQ Which inserts fit this parting clamp holder? The holder is configured for Korloy MGM 3 indexable inserts; Teknik Makina’s parting clamp holder (SKU D802TM) is specified to accept that insert family. What is the maximum supported workpiece diameter? Maximum cutting diameter is Ø80 mm, enabling secure parting operations up to that workpiece size with the recommended insert and set-up. Is the cutting direction left-hand or right-hand? This clamp holder is designed for left-hand cutting direction, suitable for machines and feed arrangements that require that orientation. How deep can the parting blade engage? The parting blade supports a maximum stech depth of 17 mm, giving adequate depth for standard grooving and cut-off tasks. What are the shank and overall dimensions? Shank designation is ISO 2525 with an overall length of 150 mm, optimised for compact toolposts and easy tool changes. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com
8.5mm Cut-Off Tool Holder L100mm 4.7mm Tip Width, T6 Torx - Teknik Makina
Take advantage of precise clamping in a compact form factor: the combination of a Ø8 mm shaft, L100 mm overall length and a cutting height of 18 mm ensures stable parting operations with minimal vibration and consistent insert support — order directly via Metav Werkzeuge or contact our technical consultants for application advice. 8.5 mm parting clamp holder K830TM — compact clamp for precise parting and grooving Parting clamp holder K830TM offers a compact, rigid solution for parting-off and narrow grooving tasks in small- to medium-sized turning centres, designed for secure insert clamping and dependable repeatability. Shaft Ø8 mm for rigid mounting Overall length L100 mm for confined spaces Cutting height 18 mm for insert compatibility Torx T6 screw M2x5 for secure fastening Rigid mounting and dependable repeatability for shop-floor use The compact clamp is built around a Ø8 mm shaft that provides a stiff connection to the tool post, reducing chatter during interrupted cuts. This stiffness translates into consistent parting results and fewer rejected components on batch runs. The relatively short L100 mm overall length minimises overhang, improving dynamic stability on smaller lathes or when working in tight fixtures. Operators benefit from predictable behaviour in production, while engineers gain clarity when integrating the holder into existing tool setups. Precise insert positioning and secure fastening for reliable performance A cutting height of 18 mm places the cutting edge in the correct plane for many standard parting inserts, reducing the need for frequent tool offset adjustments. The clamping system uses a Torx T6 drive and an M2x5 screw to deliver repeatable clamp force and straightforward reassembly after index changes. Fewer adjustments mean less machine downtime and a smoother workflow for staff who must maintain throughput while keeping quality tolerances. Designed for compact operations and straightforward maintenance With a total weight of 0.38 kg and compact dimensions, the holder is well suited to job-shop environments where space and flexibility matter. The geometry is optimised for short overhangs and easy access when inserting or removing the tool, which speeds up changeovers. Clear, robust fixing hardware reduces the risk of loosening under load and simplifies routine checks, so production managers can rely on steady output without complex maintenance cycles. Contact Metav Werkzeuge for a technical consultation or to secure the K830TM parting clamp holder from Teknik Cutting Tools for improved shop-floor stability and repeatable parting performance Technical data SKU: K830TM Label: 8.5 mm parting clamp holder L100 mm Product type: Parting clamp holder Manufacturer: Teknik Cutting Tools Facts Shaft diameter: 8 mm Overall length: 100 mm Nominal diameter: 8.5 mm Cutting height: 18 mm Clamping head width: 4.7 mm Maximum parting depth: 2 mm Weight: 0.38 kg Torx key: T6 Torx screw: M2x5 eClass: 21181005 Special features Boring bar designation: S08H Categories: Klemmhalter (clamp holders) SKU identifier: K830TM FAQ What materials is this clamp suitable for? The K830TM parting clamp holder is intended to hold inserts for machining a wide range of turning materials; compatibility is defined by the chosen insert geometry rather than the clamp itself. How is the insert secured and indexed? Insert clamping relies on a Torx T6 drive and an M2x5 screw for secure, repeatable positioning — the K830TM provides the mechanical interface for that fastening system. Can the holder be used on small lathes with limited tool post space? Yes, the compact L100 mm length and Ø8 mm shaft make the holder suitable for installations where reduced overhang and compact tool configurations are required. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com
8mm Mini Cut-Off Holder 25mm Cutting Height S16 D08 K25 L095 For NFTG 11 Inserts Innenkühlung Right-Hand Cutting - Teknik Makina
Taking advantage of compact design, proven insert compatibility and stable clamping, this tool ensures reliable parting and grooving in confined setups; order directly through Metav Werkzeuge or request tailored technical advice from our specialists. Mini parting clamp holder – 16 mm shank, for NFTG11 inserts (Teknik Makina) A Mini parting clamp holder engineered for accurate grooving and parting operations in small to medium workshop lathes, compatible with Korloy NFTG11 indexable inserts. Compact 16 mm shank for tight machine setups Compatible with Korloy NFTG11 inserts 95 mm overall length for reduced overhang Lightweight 0.126 kg for improved stability Precise insert compatibility reduces setup uncertainty The holder is optimised for use with NFTG11 indexable inserts and original Korloy geometries, delivering reproducible seating and predictable cutting behaviour. The clamping concept is designed to work with standard grooving inserts, so tool life and process stability are enhanced by correct insert seating; this reduces time spent on trial adjustments and supports consistent part quality. For shops using standard Korloy grade inserts, the integration with the tooling system is straightforward and traceable. Minimal overhang and compact shaft for stable cuts With a 16 mm shank and a 95 mm overall length, the design minimises unsupported overhang and reduces chatter in narrow working envelopes. The reduced mass, at 0.126 kg, lowers centrifugal and vibration effects during higher spindle speeds, while the listed 8 mm cutting diameter aligns with common small-groove applications. These dimensional choices translate into a more rigid setup and fewer rejected parts from vibration-induced errors, enabling more efficient cycle times with less rework. Workshop-ready design for straightforward integration The clamping tool is supplied in a format that matches the S16 tool-bar designation and the D08 K25 L095 clamp-bar reference, simplifying inventory management and tool change routines. The compact clamp holder is particularly suitable for job shops and specialised turning departments that require quick tool swaps and reliable repeatability. Where a compact grooving solution is required, this holder bridges off-the-shelf insert availability with easy installation into common small-lathe tool posts, helping maintain a steady production flow without complex adaptations. Contact Metav Werkzeuge for personalised tooling advice and exact compatibility checks for Teknik Makina parts; call +49 2822 7131930 or email info@metav-werkzeuge.com Technical data Article number: K802TM Manufacturer: Teknik Makina Article name: Mini Stechklemmhalter Core technical data Shank diameter: 16 mm Cutting height: 25 mm Cutting diameter: 8 mm Overall length: 95 mm Weight: 0.126 kg Compatible insert type: NFTG 11 Compatible insert manufacturer: Korloy Bar designation: S16 Clamping bar reference: D08 K25 L095 Special features Compact clamping design for parting/grooving Suited to insert-based grooving systems Low-mass construction for reduced vibration Designed for small and medium lathe tool posts FAQ What inserts fit this clamping holder? The holder is specified for NFTG11 indexable inserts and is designed to work with Korloy insert geometries for reliable seating and cutting performance. Which shank diameter does the holder use? The tool features a 16 mm shank, compatible with S16 tool-bar installations commonly found in compact lathe setups. Is the holder suitable for narrow grooving tasks? Yes, the compact dimensions and an indicated cutting diameter of 8 mm make it well suited for narrow grooving and parting operations in confined workspaces. How does the tool help reduce vibration? A short 95 mm overall length combined with a lightweight construction (0.126 kg) reduces unsupported overhang and contributes to greater rigidity, lowering the risk of chatter. Can this holder be integrated into existing tool setups? The holder matches standard S16 bar specifications and the D08 K25 L095 clamping reference, enabling straightforward integration into compatible tool posts and bars. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com
8mm Mini Grooving Tool Holder D08 For Indexable Inserts, S16 Shank D08 K11 L093, 11mm Cutting Height, Internal Cooling - Teknik Makina
Take advantage of a compact, high‑precision mini grooving clamping holder that combines a 16 mm shank with an 11 mm cutting height for stable, repeatable grooving and parting operations; order directly via Metav Werkzeuge or consult its technical advisors for suitability checks. Mini grooving clamping holder K810TM — compact clamp holder for indexable inserts, 16 mm shank (Teknik Cutting Tools) A Mini grooving clamping holder K810TM designed for compact turning centres and lathe setups, suited to grooving and parting tasks with D08 indexable inserts. Compact 16 mm shank for tight setups Compatible with D08 indexable inserts 11 mm cutting height for stable cutting Lightweight 0.098 kg for reduced spindle load Precision and stability in confined toolposts The compact design delivers stable clamping where space is limited. The combination of a 16 mm shank and a short overall length means the toolholder offers reduced overhang and improved rigidity, which lowers vibration and improves surface finish. The holder’s 11 mm cutting height matches standard insert geometries, ensuring correct insert seating and consistent cutting planes; this promotes reliable process control and repeatable results on serial work. The lightweight construction (0.098 kg) minimises additional load on the spindle, helping maintain concentricity during higher spindle speeds. Faster insert changes and predictable tool life Designed around D08 inserts, the clamping concept supports quick indexable‑insert swaps to reduce downtime. The holder accepts standard insert geometry so indexable inserts can be rotated or replaced without regrinding, delivering a predictable tool‑life strategy and lower per‑part machining costs. The shank designation S16 indicates compatibility with common 16 mm shank toolposts, simplifying tool library management across machines. Clear seating and secure clamping reduce insert movement under load, which benefits cycle time and reduces scrap rates in small‑batch production. Suited to workshops that value versatility and trust The mini clamping tool performs well in high‑mix, low‑volume environments and on compact lathes where accessibility and repeatability matter. Its compact design and compatibility with widely available inserts make it a practical choice for job shops, maintenance departments and precision workshops that require fast changeovers and reliable results. Backed by Metav’s supply chain and quality control, the K810TM supports a dependable workflow from stock to shop‑floor, reinforcing operational continuity and reducing procurement complexity. Contact Metav Werkzeuge for a detailed machine‑compatibility check and a tailored delivery proposal for the Teknik Cutting Tools Mini grooving clamping holder K810TM; Metav’s technical advisors will confirm suitability, lead times and supply from Emmerich Technical data Article number: K810TM Manufacturer: Teknik Makina Insert type: D08 Shank designation: S16 Shank diameter: 16 mm Cutting height: 11 mm Overall length: 93 mm Weight: 0.098 kg Diameter: 8 mm Core technical data Shank diameter: 16 mm Cutting height: 11 mm Overall length: 93 mm Weight: 0.098 kg Diameter: 8 mm SKU: K810TM Compatible insert: D08 Special features For indexable inserts D08 S16 shank designation Compact design for tight setups Lightweight construction 0.098 kg Intended for grooving and parting operations FAQ Which insert type fits this holder? The mini grooving clamping holder accepts D08 indexable inserts; the holder is engineered for standard D08 seating and clamping. What shank size does the holder use? Shank diameter is 16 mm (shank designation S16), suitable for 16 mm toolposts and holders. Is the holder suitable for compact lathes? Yes — the compact overall length of 93 mm and lightweight design make the holder well suited to small turning centres and confined toolpost spaces. How does the clamping concept affect insert life? Secure seating and consistent cutting height reduce insert movement and uneven wear, which helps to extend the useful life of indexable inserts and stabilise process outcomes. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com
Grooving Holder - Teknik Makina
Take advantage of a purpose-built grooving holder that fits the clamping-holder category and is offered by Teknik Makina; the RP114TM delivers straightforward integration into workshop tooling stocks and reliable positioning for grooving tasks. Order or request advice directly via Metav Werkzeuge for a seamless supply and selection process. Grooving Holder — Stechklemmhalter for secure grooving clamping (Teknik Makina) Grooving Holder designed for secure clamping in grooving applications and integration into standard clamping-holder setups Secure clamping for grooving applications Fits the clamping-holder category Model RP114TM by Teknik Makina Reliable clamping for consistent grooving results The grooving holder provides a stable interface between tool and machine, aimed at repeatable positioning for grooving operations. With a focus on secure clamping and predictable alignment, the design reduces the need for frequent readjustment and supports steady cutting conditions. This leads to fewer stoppages for re-clamping and contributes to improved process efficiency on the shop floor. Integrates with existing clamping-holder arrangements Made to be used within the clamping-holder family, the unit is suitable where consistent tool hold and quick changeover are priorities. Its compatibility with common holder arrangements supports flexible tooling layouts and helps to keep set-up times low. The clear category alignment simplifies procurement and inventory management for workshops and small-series production. Practical benefits for workshop and small-batch production By focusing on robust clamping and straightforward handling, this holder helps maintain machining accuracy over repeated cycles. The combination of precise seating and a reliable interface minimises vibration transfer and supports better surface finishes in grooving tasks. For operations that value consistent results and predictable tool behaviour, the RP114TM represents a sensible component choice. Selection guidance and maintenance considerations Choose the RP114TM when dedicated grooving clamping is required and when alignment repeatability is a priority. Routine visual checks and correct installation ensure continued performance; in standard industrial practice, correct mounting and torqueing maintain positional accuracy and extend service life. For tailored advice on fitment and system compatibility, technical consultation is recommended. For expert guidance on selecting the right Teknik Makina Grooving Holder RP114TM and to secure dependable tooling supply from Metav Werkzeuge, contact our consultants in Emmerich by e‑mail or phone and benefit from our decades of metrology and tooling expertise Technical Data Article number: RP114TM Manufacturer: Teknik Cutting Tools Product type: Grooving holder Facts eClass: 21181005 Special features Category: Klemmhalter (Clamping holders) Label: Stechklemmhalter Intended application: Grooving operations FAQ What is the primary application of this grooving holder? The grooving holder RP114TM is intended for secure clamping in grooving operations within clamping-holder setups and supports repeatable positioning. Is the RP114TM compatible with standard clamping-holder arrangements? Yes, the RP114TM by Teknik Makina is designed to integrate into common clamping-holder configurations used in workshops. How does this holder help improve machining consistency? Stable clamping and precise seating from the holder reduce vibration and positional variation, supporting consistent groove geometry and surface quality. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com
Grooving Holder 110mm Clamping Type, Heavy Duty - Teknik Makina
Take advantage of a purpose-built grooving holder that provides secure clamping and clear identification for tool management; its compact design supports efficient grooving operations while the SKU RP110TM ensures straightforward stock control. Order through Metav Werkzeuge or consult their advisors for fitment and integration. Grooving holder RP110TM — compact grooving clamping solution by Teknik Makina Grooving holder RP110TM is a compact clamping device designed for precision grooving applications in machining environments Robust clamping for grooving operations Compact design for tight tool setups Clear identification: SKU RP110TM Reliable clamping for precise grooving A dedicated grooving clamping device simplifies the task of creating consistent grooves across workpieces. The grooving holder is engineered to provide repeatable positioning and secure fixing during machining, reducing setup variability and downtime. The clear SKU designation, RP110TM, supports inventory control and traceability, so workshop planners can allocate tooling with confidence and maintain consistent process quality. Streamlined workflow and tool management Integrating this clamping solution into an existing toolpost or turret simplifies changeovers and keeps machining cycles efficient. With its compact footprint, the holder enables closer tool spacing and supports denser tool layouts on the machine, which can shorten non-cutting times. Clear labelling and standardised identification aid workshop logistics, making replenishment and routine checks faster and more reliable for production teams. Durable sourcing and practical shop-floor benefits Sourcing the grooving holder from a recognised supplier such as Teknik Makina and distributing via Metav brings logistical reliability to the workshop. Centralised procurement through Metav reduces administrative overhead and ensures consistent supply. For engineers and workshop managers seeking predictable availability and straightforward part identification, this clamping solution supports continuity of production and measurable process control. Contact Metav Werkzeuge for a practical assessment of the RP110TM grooving holder and a recommendation for integration into the current tool setup Technical data SKU: RP110TM Article designation: Grooving holder Manufacturer: Teknik Makina EClass: 21181005 Facts No dimensional data supplied No weight data supplied Special features Intended use: grooving operations Category: clamping holders (machining) Clear identification for tool management FAQ What applications is this holder suited to? The RP110TM grooving holder is intended for grooving operations in general machining and toolpost setups where secure clamping and repeatable positioning are required. Which machines is the holder compatible with? Compatibility depends on the machine tool’s toolpost or turret and the clamping arrangement; the RP110TM is designed as a standard grooving clamping device for typical machining setups. Can the grooving holder be used with different insert types? Insert compatibility is determined by the toolhead and insert geometry; the grooving holder provides the clamping platform, while insert selection must match the groove geometry and cutting parameters. How is the product identified in inventory? This grooving holder is identified by the SKU RP110TM and its designation as a grooving holder, which simplifies tracking and stock management. Is technical specification data available for load or dimensions? The supplied product information does not include dimensional or load specifications; for detailed mechanical data, confirmation of machine interface and application specifics is recommended Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com
Grooving Holder 12mm Clamping Type - Teknik Makina
Take advantage of reliable grooving clamping and simplified procurement: the RP112TM Stechklemmhalter from Teknik Cutting Tools provides stable tool holding for grooving operations and clear identification for ordering. Buy directly through Metav Werkzeuge or consult our specialists for suitability in specific turning setups. Stechklemmhalter RP112TM — Grooving holder with secure clamping Stechklemmhalter is a grooving clamping holder engineered for secure tool holding in industrial turning and grooving applications. Precision clamping for grooving operations Stable clamping geometry Orderable under SKU RP112TM Maximise machining reliability with consistent clamping A clamping holder is central to consistent grooving processes: the RP112TM focuses on precision clamping to reduce tool movement and vibration during cuts. Stable tool retention results in more consistent groove profiles and improved surface quality. For workshops that prioritise repeatable results, a dedicated grooving holder contributes directly to process predictability and fewer reworks. Straightforward integration into existing workshop toolsets The RP112TM is presented as a purpose-built grooving solution that eases integration into common turning set-ups. With a clear SKU for procurement and a design intended for routine mounting, this holder supports organised tooling inventories and fast changeovers. When paired with established toolposts, a correctly mounted holder shortens setup time and helps maintain regular production cycles. Enhanced productivity and repeatability on the shop floor Stable clamping geometry translates into operational gains: fewer interruptions, steadier cutting conditions and improved cycle consistency. Such benefits are particularly relevant in batch production or repetitive grooving tasks, where cumulative time savings and reduced scrap add measurable value. The holder contributes to overall process efficiency by securing the cutting edge in a defined position for repeated passes. Procurement confidence and workshop support from an established partner Sourcing the RP112TM via Metav brings the advantage of a supplier with deep sector experience and a broad product portfolio. Metav’s position as a reliable distributor ensures transparent order handling and steady supply for workshop needs. With more than 48,000 customers trusting Metav’s range, buyers gain the reassurance of a quality‑focused supply chain for their clamping and workholding requirements. For procurement or technical clarification on the Teknik Cutting Tools Stechklemmhalter RP112TM, contact Metav Werkzeuge for availability and order support via info@metav-werkzeuge.com or phone +49 2822 7131930. Technical data SKU: RP112TM Product type: Stechklemmhalter eClass: 21181005 Facts Category: Klemmhalter (clamping holders) Application area: Grooving Special features Intended use: grooving workholding Manufacturer: Teknik Cutting Tools Identifier: RP112TM FAQ What is the primary use of this holder? The Stechklemmhalter RP112TM is intended for grooving applications and secures the cutting tool for consistent groove formation. Is the RP112TM suitable for production turning? Yes, the RP112TM is designed as a grooving clamping holder to support repetitive turning and grooving tasks with stable tool retention. How is the product identified when ordering? Order the grooving holder under SKU RP112TM; the designation refers to the Teknik Cutting Tools grooving clamping holder. Does this holder improve repeatability in batch work? By ensuring stable clamping geometry, the RP112TM supports repeatable tool positions and consistent groove profiles across multiple workpieces. Where can more technical information be obtained? Technical queries relating to the Stechklemmhalter RP112TM can be addressed through Metav Werkzeuge; they provide detailed product selection and procurement guidance. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com
Fast, reliable parting and grooving for precision turning
Parting and grooving tools, also referred to as parting blades, grooving tools or cut-off tools, are narrow carrier tools for lathes fitted with replaceable carbide inserts. Supplied as solid holders or flat blades, they are designed to cut precise grooves and to part finished components cleanly from the material bar.
Why internal coolant matters for deep cuts and tough materials
When used in simple form without internal coolant, the cutting fluid is applied via external machine nozzles; this is often sufficient for very shallow grooves and easily machinable materials. For deeper grooving and parting operations, however, the tool nearly encloses the slot so that external coolant cannot reach the cutting edge. Tools with internal coolant incorporate fine, integrated channels that deliver coolant under high pressure directly to the insert and beneath the chip. This targeted supply controls the intense heat in the confined cutting zone and uses flushing pressure to eject chips reliably, preventing chip jamming, surface damage and sudden tool breakage.
Clear operational benefits you can measure
- faster cycle times through reliable chip evacuation and uninterrupted cutting
- extended tool life thanks to effective heat control at the cutting edge
- consistent surface finish by avoiding chip re-cutting and scarring
- safer machining of hard or ductile materials due to reduced risk of tool fracture
- simplified setup when holders with integrated channels replace complex external coolant rigs
Metav as a practical partner for your workshop
Metav stands for democratisation of precision: decades of expertise, a quality filter in Emmerich and an assortment that supports industry and trade. With more than 48,000 customers and a catalogue of over 250,000 products, Metav provides a focused selection of parting and grooving tools, accessories and matched holders so that procurement and technical choice remain straightforward and dependable.
Parting and grooving tools bring reliable groove geometry and safe parting to turning operations; choosing holders with integrated coolant channels is essential for deep cuts and demanding materials. If technical advice is needed, Metav’s product specialists can help select the appropriate tool geometry and coolant configuration for the application.
FAQ
When is internal coolant necessary for parting tools?
Internal coolant becomes necessary for deep grooving and parting or when machining hard or ductile materials; it delivers coolant directly to the insert and beneath the chip, which is critical when external nozzles can no longer reach the cutting edge.
Can parting tools be used without internal coolant?
Yes — for very shallow cuts and easily machinable materials, parting tools can be used with external machine coolant nozzles, but performance and tool life will drop markedly for deeper cuts.
How do parting tools prevent dangerous chip jamming?
Parting tools with integrated channels use high-pressure coolant to flush chips out of the narrow slot, preventing chips from becoming trapped and minimising the risk of surface damage and abrupt tool failure.
What should be considered when choosing a grooving insert and holder?
Select a combination that matches the required groove depth and material grade; holders offering integrated high-pressure channels are preferred for deep cuts or poor-chip-breaking materials to ensure heat control and reliable chip evacuation.
Fragen zu diesen Produkten??
Mit mehr als 30 Jahren Erfahrung beraten wir Sie gerne persönlich.
Tel.: +49 2822 7131930
Mail: info@metav-werkzeuge.com