Precision cut-off tools for accurate grooving and part-off operations
Cut-off tools are narrow holder systems for lathes designed to produce precise grooves and part-offs, offering reliable control when machining steels and other workpiece materials where clean separation is essential. They serve as either solid clamp-style holders or flat tool blades fitted with indexable carbide inserts, and when equipped with internal coolant channels they deliver high-pressure coolant directly to the insert to control heat and evacuate chips efficiently. Using these tools reduces the risk of chip jamming, surface damage and sudden tool failure while improving repeatability, particularly in deep grooving and tough materials where external coolant is insufficient. Key advantages include enhanced cutting stability, extended insert life and consistent part quality through optimised chip evacuation and thermal management.
125mm Stechklemmhalter 2mm Cutting Width, Max 18mm Depth, ISO 2020, Compatible with Sandvik, Left-Hand Cutting, Internal Cooling - Teknik Makina
Combining precise left‑hand cutting with a narrow 2 mm cutting width and a secure clamping geometry delivers dependable parting and grooving performance in production and repair shops; order the holder directly via Metav Werkzeuge or request specialist advice from our consultants for suitable setup and inserts. Teknik Makina Stechklemmhalter — left‑hand parting tool holder with 2 mm cutting width A robust steel tool holder designed for left‑hand parting and grooving operations, compatible with Sandvik indexable inserts in ISO 2020 format and intended for secure installation in 2C‑123 SDV‑L tool shanks Left‑hand cutting for plunge and grooving 2 mm cutting width for narrow parting cuts 125 mm overall length for secure reach Compatible with Sandvik ISO 2020 inserts Consistent parting quality through engineered geometry The holder is engineered to maintain a stable cutting line and predictable chip flow during longitudinal cutting and plunge operations. Its left‑hand cutting orientation and 2 mm cutting width provide a narrow kerf suitable for close tolerances and minimal material waste. The combination of narrow cutting width and a defined 18 mm maximum plunge depth allows controlled engagement when entering the workpiece, reducing chatter and improving surface finish. This stability translates into fewer rejected parts and less secondary machining, supporting efficient production cycles. Stable clamping and repeatable set‑ups for toolrooms A compact yet rigid construction keeps the cutting edge precisely positioned: the tool offers a holder height of 20 mm, holder width of 20 mm and a head width of 20 mm, giving a robust contact area for the clamping screws. The specified shank form 2C‑123 SDV‑L provides a straightforward fit in compatible toolposts and reduces set‑up time. With a mass of 0.4 kg, the assembly balances rigidity with manageable handling during tool changes, ensuring repeatable set‑ups and consistent cutting results across serial runs. Compatibility and workflow benefits for mixed fleets Designed to accept Sandvik‑compatible indexable inserts in the ISO 2020 size, the holder integrates easily into existing insert inventories and reduces the need for multiple specialised parting tools. The 125 mm overall length gives sufficient reach for most lathe turrets while keeping the overhang moderate to limit deflection. For workshops seeking cost‑effective standardisation, this holder reduces tool diversity without compromising capability, helping to streamline ordering and inventory management. For reliable left‑hand parting operations, contact Metav Werkzeuge to order the Teknik Makina Stechklemmhalter (SKU D873TM) or to request specialist advice from Emmerich on the best insert choices and set‑up options. Technical data SKU: D873TM Manufacturer: Teknik Makina Weight: 0.4 kg Overall length: 125 mm Facts Holder height: 20 mm Holder width: 20 mm Head width: 20 mm Cutting width: 2 mm Max plunge depth: 18 mm Shank designation: 2C-123 SDV-L ISO designation: 2020 Cutting direction: left Special features Compatible with Sandvik indexable inserts Designed for parting and grooving operations Robust clamping geometry for repeatability FAQ What types of inserts fit this holder? The holder accepts ISO 2020 indexable inserts; it is specified as Sandvik‑compatible, making standard Sandvik parting inserts suitable for the application. Is the holder suitable for plunge cutting on shafts? Yes. The holder’s 18 mm maximum plunge depth and narrow 2 mm cutting width are intended for controlled plunge and parting tasks on cylindrical workpieces. Which shank or toolpost does the holder require? The tool is designed for use with a 2C‑123 SDV‑L shank designation, providing a secure fit in matching toolholders and reducing set‑up time. How does the holder contribute to vibration control? A compact contact area—20 mm in height and width combined with the robust head—reduces overhang and increases stiffness, helping to control vibration and improve surface finish during high‑demand cuts. Can this holder be used in mass production environments? Yes. The combination of repeatable clamping geometry, standard ISO 2020 insert compatibility and a moderate 125 mm overall length makes it suitable for serial production where consistent parting performance is required. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com
125mm Stechklemmhalter 2° 2020 2C GX24 for GX24 Wendeplatten Innenkühlung - Teknik Makina
Take advantage of a compact combination of secure clamping, exact 2 mm cutting capability and a 125 mm overall length for reliable parting and grooving operations. Order the holder directly via Metav Werkzeuge or consult the team for tailored application advice. Stechklemmhalter – Parting tool holder with 2 mm cutting width | Teknik Makina Stechklemmhalter designed for precise parting and grooving on lathes, compatible with Walter GX24 indexable inserts and optimised for tight, repeatable cuts 2 mm cutting width for narrow grooves 20 x 20 mm shank for secure mounting Compatible with Walter GX24 indexable inserts 18 mm maximum plunge depth Accurate narrow cuts for consistent parting The 2 mm cutting width enables precise, narrow grooves and clean parting operations. With an insert-compatible design for GX24 indexable inserts, the holder maintains repeatable geometry across multiple tool changes, reducing set-up variation. Indexable inserts are replaceable cutting edges that preserve tool alignment and minimise downtime; using a dedicated clamping unit ensures consistent seat contact and reliable chip control during short, high-precision cuts. Secure mounting and stable clamping reduce vibration A square shank with an ISO designation 2020 and nominal dimensions of 20 x 20 mm provides a firm interface with standard tool posts and quick-change systems. The clamping arrangement holds the insert seat and cutting head dimensions of 20 mm to maintain rigidity during plunge and grooving tasks. Reduced deflection supports predictable tool life and improved surface quality, which is particularly beneficial in serial turning where every micrometre of deviation affects downstream processes. Compact design to boost workshop throughput With an overall length of 125 mm and a mass of 0.403 kg, the unit balances accessibility and stability for typical lathe setups. The 18 mm maximum plunge depth permits controlled engagement for deeper grooves without excessive overhang. The slim geometry and compatibility with the 2C GX24 bar designation make the clamping holder a practical choice for confined workspaces and processes that require frequent insert changes, helping to shorten cycle times and streamline production flows. For expert application support or to secure stock of this Teknik Makina parting tool holder, contact Metav Werkzeuge for product availability and practical recommendations tailored to the turning task at hand – Metav Werkzeuge is ready to advise and supply from Emmerich. Technical Data Article number: D864TM Manufacturer: Teknik Makina Designation: Stechklemmhalter ECLASS: 21181005 Facts Shank height: 20 mm Shank width: 20 mm Cutting head width: 20 mm Cutting width: 2 mm Maximum plunge depth: 18 mm Overall length: 125 mm Weight: 0.403 kg ISO designation: 2020 Special features Compatible with inserts: GX24 Compatible insert manufacturer: Walter Compatible boring bar designation: 2C GX24 Suitable for parting and grooving operations FAQ What inserts fit this clamping holder? The clamping holder accepts GX24 indexable inserts and is specified for inserts from Walter, ensuring a standardised seating and cutting geometry. What is the maximum plunge depth for this holder? The tool offers a maximum plunge depth of 18 mm, allowing controlled engagement for deeper grooves within that limit. Which shank size should the tool post accept? The square shank conforms to 20 x 20 mm (ISO 2020) dimensions for secure mounting on compatible tool posts and quick-change systems. Is the holder suitable for confined lathe setups? Yes; the compact 125 mm overall length and modest weight support installation in restricted work envelopes while maintaining stability. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com
125mm Stechklemmhalter 2° 2020 2C-L MGM For 2C MGM Innenkühlung Linksschneidend - Teknik Makina
Take advantage of a compact, left-hand parting tool holder that combines precise clamping, compatibility with Korloy 2C MGM inserts and a rigid 20 × 20 mm ISO shank for consistent repeatability on turning machines — order directly via Metav Werkzeuge or request guidance from our workshop consultants. Parting Tool Holder D610TM — Left-hand, 2 mm cutting width (Teknik Makina) The Parting Tool Holder D610TM is a left-hand parting and grooving holder designed for lathe toolposts, accepting Korloy 2C MGM inserts and matching an ISO 2020 20 × 20 mm shank for stable machining. Left-hand cutting orientation Accepts Korloy 2C MGM inserts ISO 2020 20 × 20 mm shank 2 mm cutting width, 16 mm max depth Stable clamping that reduces chatter and rework The D610TM delivers positive clamping and consistent seating with a compact 20 × 20 mm shank that matches ISO 2020 tooling systems. The holder’s geometry provides a secure grip on the insert carrier, which improves repeatability from cut to cut and reduces the need for rework. For workshops seeking reliable parting performance, the robust clamping reduces vibration and supports more predictable cycle times on production and repair jobs. Efficient material removal with controlled cutting depth Designed for narrow-section operations, the holder supports a 2 mm cutting width and a maximum parting depth of 16 mm, enabling controlled engagement for fine parting and grooving. The left-hand orientation suits left-oriented setups or specific part geometries, while the defined width helps maintain chip shape and stability. These characteristics translate into fewer tool changes and better surface integrity during turning operations, improving throughput on batch and single-piece work alike. Compact footprint for versatile workshop integration With an overall length of 125 mm and a nominal weight of 0.404 kg, the tool holder offers a compact package that fits confined toolpost spaces without sacrificing stiffness. The modest dimensions make it especially suitable for small lathes or multi-station turrets where tool spacing is critical. The holder’s balance between compactness and rigidity supports steady cutting conditions, helping to preserve insert life and reduce downtime. Broad compatibility for simplified tooling management Compatibility with Korloy 2C MGM inserts and the designation matching 2C-L MGM clamping bars means straightforward integration into existing tooling inventories. The ISO 2020 shank dimension ensures interchangeability with standard holders and post systems, simplifying stock and reducing procurement complexity. For production environments aiming to minimise tooling variants, this holder provides a clear technical fit to established insert families and mounting conventions. Choose the Teknik Makina Parting Tool Holder D610TM via Metav Werkzeuge for dependable parting performance — our Emmerich-based team provides product guidance and rapid supply to keep workshop schedules on track; contact Metav Werkzeuge at info@metav-werkzeuge.com or +49 2822 7131930 for technical advice and order support Technical Data SKU: D610TM Manufacturer: Teknik Makina Designation: Parting tool holder Shank size: 20 × 20 mm (ISO 2020) Cutting direction: left Compatible inserts: Korloy 2C MGM Cutting width: 2 mm Max parting depth: 16 mm Overall length: 125 mm Weight: 0.404 kg Key Figures Shank height: 20 mm Shank width: 20 mm Cutting width: 2 mm Max cutting depth: 16 mm Overall length: 125 mm Weight: 0.404 kg Special features ISO designation: 2020 Bohrstangen designation: 2C-L MGM Suitable for Korloy 2C MGM inserts FAQ What insert type is required for this holder? The holder is made for Korloy 2C MGM inserts; the D610TM accepts the 2C geometry and secures the insert with the matching clamping arrangement. Is the cutting direction left or right? This tool holder is a left-hand model; its geometry and seat are oriented for left-hand cuts on the lathe. What shank size does the holder use? The D610TM uses a 20 × 20 mm shank, conforming to the ISO 2020 dimension for easy integration into standard toolposts. How deep can the parting operation be with this holder? The maximum parting depth is 16 mm, with a cutting width of 2 mm suitable for narrow grooving and parting tasks. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com
125mm Stechklemmhalter 2°? 1616 2C-R DGN for 2C DGN Wendeplatten Innenkühlung Rechtsschneidend - Teknik Makina
Take advantage of a compact, rigid holder with a 16×16 mm shank and a 2 mm cutting width to secure consistent right‑hand parting and grooving operations — order the tool directly via Metav Werkzeuge or contact our consultants for application advice. Parting/clamping holder D752TM – right‑hand grooving holder, 16×16 mm (Teknik Makina) The parting/clamping holder D752TM is designed for right‑hand grooving and parting tasks on modern lathes, offering a compact 125 mm overall length and compatibility with 2C DGN indexable inserts 16×16 mm shank for robust clamping 2 mm cutting width for precise parting 16 mm maximum plunge depth Compatible with ISCAR 2C DGN inserts Consistent rigidity for uninterrupted production A solid 16×16 mm shank combined with a compact 125 mm overall length provides mechanical stability that reduces vibration during cutting. The holder’s low mass (0.26 kg) and compact footprint make it suitable for both busy production lines and smaller job‑shop lathes. This structural stability translates into steadier cuts, less tool chatter and improved surface finish, which helps maintain cycle times and reduces the need for rework. Predictable cutting performance through standardised insert use Designed for 2C DGN indexable inserts and compatible with ISCAR tooling, the holder accepts a narrow 2 mm cutting width and allows a 16 mm maximum plunge depth. Using standard insert formats simplifies tool management and regrinding schedules while ensuring repeatable chip evacuation and dimensional control. The right‑hand orientation suits the most common turning set‑ups, offering a clear, engineering‑driven advantage when processing narrow grooves or parting off finished components. Practical integration into workshop workflows The holder’s ISO 1616 shank designation and the secondary designation 2C‑R DGN support straightforward mounting and replacement in existing tool turrets. Its compact dimensions free up turret stations and allow closer tool packing, which benefits multi‑operation turning cells. For maintenance and procurement teams, the standardised interfaces reduce inventory complexity and speed up changeovers — factors that contribute directly to higher machine availability and lower per‑part production cost. For tailored advice and reliable supply from Metav Werkzeuge in Emmerich, contact our specialists to discuss the D752TM parting/clamping holder and find the optimal insert and machining parameters for the application Technical data Article number: D752TM Manufacturer: Teknik Makina Designation: Parting/clamping holder D752TM SKU: D752TM Facts Shank width/height: 16 mm × 16 mm Cutting width: 2 mm Maximum plunge depth: 16 mm Overall length: 125 mm Weight: 0.26 kg Cutting direction: right Special features Compatible with 2C DGN indexable inserts Suitable for ISCAR inserts (manufacturer reference) ISO designation: 1616 Secondary shank/bezel designation: 2C‑R DGN Application: parting and grooving in turning operations FAQ What insert types are recommended for this holder? The D752TM accepts 2C DGN indexable inserts; ISCAR‑type 2C DGN inserts are a standard match for predictable chip control. Is the holder suitable for deep grooving operations? The holder permits a maximum plunge depth of 16 mm, which is adequate for many parting and medium‑depth grooving tasks on lathes. Which machines is this holder intended for? This compact holder is designed for turret‑mounted turning centres and conventional lathes where a 16×16 mm shank can be accommodated and where right‑hand cutting is required. How does the holder support repeatable results? Standardised shank dimensions (ISO 1616) and compatibility with common insert formats ensure repeatable clamping, quick replacement and consistent machining tolerances. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com
125mm Stechklemmhalter 3mm Cut Width, 16mm Max Stechdepth, 1212, -3C-L DGN, For 3C DGN Indexable Inserts, Left-Hand Cutting, Innenkühlung - Teknik Makina
Take advantage of a compact holder that combines precise left-hand parting with minimal tool overhang and reliable clamp-style fixation. The D730TM offers a 3 mm cutting width and a maximum parting depth of 16 mm, enabling efficient short-run parting and grooving in confined turning operations. Order the parting clamp holder directly via Metav Werkzeuge or ask our consultants if needed. Parting clamp holder D730TM — Left-hand parting tool holder by Teknik Makina The Parting clamp holder D730TM is a left-hand clamp-style holder for parting and grooving, designed for use with ISCAR indexable inserts in demanding lathe operations. Left-hand cutting direction Compatible with ISCAR 3C DGN inserts 3 mm cutting width Overall length 125 mm Accurate, repeatable parting for tighter tolerances The clamp-style design delivers stable clamping and reduced vibration, which supports consistent parting performance and repeatable results. By securing the insert with a compact clamping block, the holder minimises play during cut engagement; this translates into fewer rejects and less rework when producing turned components. The ISO designation 1212 ensures a standardised interface for insert seating and orientation, simplifying insert replacement and inspection. Short set-up times and efficient machining cycles With a modest overall length of 125 mm and a low mass of 0.16 kg, the holder reduces tool overhang and inertia, enabling faster acceleration and safer clearances during program cycles. The simple geometry and clamp mechanism cut setup time and allow quick insert changes, supporting lean production flows and higher machine uptime. These features make the D730TM suitable where rapid changeovers and throughput are priorities. Compact form for constrained turning operations Where carriage travel or cross-slide clearance is limited, the compact dimensions (holder height 12 mm; holder width 12 mm) permit close-to-workpiece machining without sacrificing cutting stability. The narrow 3 mm cutting width is ideal for fine parting, slotting and narrow-groove applications, allowing precise control of chip evacuation and reduced cycle loads in small-diameter workpieces. Proven compatibility and practical application advice Engineered for use with ISCAR 3C DGN indexable inserts, the holder accepts standard insert sizes and can be integrated easily into existing tool setups. The left-hand cutting orientation is suitable for operations where the tool must cut when travelling from tailstock to headstock; match the holder to lathe setup and insert geometry to achieve the best surface finish and tool life. For specific applications and recommended cutting parameters, Metav Werkzeuge’s technical advisors can provide guidance. Contact Metav Werkzeuge for tailored application advice on the Teknik Cutting Tools D730TM and secure a reliable left-hand parting solution for precision turning tasks, served directly from Emmerich with swift logistical support. Technical data Article number: D730TM Manufacturer: Teknik Makina Brand: Teknik Cutting Tools SKU: D730TM Facts Overall length: 125 mm Holder height: 12 mm Holder width: 12 mm Cutting head width: 12 mm Cutting width: 3 mm Maximum parting depth: 16 mm Weight: 0.16 kg Cutting direction: left Special features Compatible with ISCAR 3C DGN inserts ISO designation: 1212 Shank/holder designation: -3C-L DGN Compact clamp-style mounting FAQ What inserts fit this holder? The D730TM is designed for ISCAR 3C DGN indexable inserts; select the matching insert geometry and grade for the machining material. Is the cutting direction left- or right-hand? This holder is specified for left-hand cutting operations and is intended for cuts made from tailstock towards headstock. What maximum parting depth can be achieved? Maximum achievable parting (stepping) depth is 16 mm, as defined by the holder geometry. What are the key dimensions to consider for set-up? Important dimensions include overall length 125 mm, holder height 12 mm, holder width 12 mm and cutting width 3 mm. Can the holder be used for narrow grooving as well as parting? Yes; the narrow 3 mm cutting width and rigid clamp fixation make it suitable for narrow-groove operations as well as standard parting tasks. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com
125mm Stechklemmhalter 3mm Cut Width, 18mm Max Depth, ISO 1212, 3C-R MGM For 3C MGM Inserts, Internal Cooling, Right-Hand Cutting - Teknik Makina
Take advantage of a compact, high-precision clamping solution that combines a 3 mm parting capacity with an 18 mm maximum cutting depth for controlled, repeatable grooving operations; order directly via Metav Werkzeuge or consult our specialists for application advice. D667TM Grooving tool clamping holder — right‑hand, 3 mm cutting width by Teknik Makina D667TM grooving tool clamping holder for right‑hand parting and grooving, compatible with Korloy 3C MGM indexable inserts and designed for compact turning toolposts Right-hand cutting orientation 3 mm cutting width for narrow grooves 18 mm maximum cutting depth Compatible with Korloy 3C MGM inserts Consistent cut quality for precision parting The D667TM delivers a compact solution for controlled parting and narrow grooving tasks. With a 3 mm cutting width and a 12 mm cutting‑head width, the design focuses on stable chip formation and predictable forces, which reduces vibration and tool chatter. The result is improved surface finish and reduced rework, particularly important when batch repeatability and tight tolerances are required. The modest 0.162 kg mass contributes to low overhang and helps maintain stiffness in short‑reach applications. Compact mounting and simplified insert changes Engineered for efficient workflow, this clamping unit uses a 1212 shank designation for easy fitment in standard toolholders and adopts a clamping geometry that speeds up insert replacement. The holder’s overall length of 125 mm keeps the cutting edge close to the toolpost, lowering leverage and improving rigidity. Quick access to the clamping screw and a straightforward insert seat reduce downtime during changeover and help maintain high machine utilisation across recurring operations. Broad compatibility and clear application range The holder accepts 3C MGM style indexable inserts and is listed as compatible with Korloy plates, ensuring access to a wide range of cutting grades and chipbreaker geometries suitable for steels and general workshop materials. Its right‑hand cutting direction is optimised for conventional lathe orientations and ensures predictable chip flow. For users seeking a compact parting solution, this component is appropriate for finishing and semi‑finishing grooves where narrow slot widths and controlled depth (up to 18 mm) are required. Reliable clamping for repeatable results A focused clamping concept combines repeatable seating with secure screw tension to maintain cutting geometry under load. The holder’s design minimises micro‑movement at the insert seat, supporting consistent tool life and dimensional stability across runs. Where process reliability matters, the combination of short overhang, precise insert placement and robust clamping contributes to fewer scrap parts and a steadier production rhythm — a clear operational advantage for workshops and small‑batch manufacturers. For dependable grooving and parting operations, contact Metav Werkzeuge for application guidance or to arrange procurement via our Emmerich team by email at info@metav-werkzeuge.com or by phone on +49 2822 7131930 Technical data Article number: D667TM Brand: Teknik Makina Item: Grooving clamping holder Core specifications Overall length: 125 mm Cutting‑head width: 12 mm Cutting width: 3 mm Maximum cutting depth: 18 mm Weight: 0.162 kg Shank designation: 1212 Compatible inserts: 3C MGM Cutting direction: right Features & compatibility Compatible with Korloy 3C MGM inserts Bohrstange designation: 3C‑R MGM Compact design for low overhang Fast insert change and secure clamping FAQ What inserts fit this grooving clamping holder? The holder accepts 3C MGM indexable inserts; it is compatibile with Korloy versions of that insert style for a range of cutting grades. What is the maximum cutting depth for this tool? Maximum cutting depth is 18 mm, suitable for most narrow grooving and parting operations that stay within short‑reach tool setups. Which direction of cut is this holder designed for? This unit is specified for right‑hand cutting, intended for conventional lathe orientations and predictable chip evacuation. What shank size is required for mounting? The holder uses a 1212 shank designation, corresponding to a compact 12 × 12 mm square interface for standard toolposts. How does the holder contribute to repeatability? Short overall length and positive clamping seating reduce leverage and micro‑movement at the insert, enhancing precision and consistent tool life across repeated cycles. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com
125mm Stechklemmhalter 3mm Cutting Width, 18mm Max Grooving Depth, 20x20mm Head - Teknik Makina
Take advantage of precise clamping, a narrow 3 mm cutting width and a compact 20 x 20 mm shank for stable, high-repeatability parting operations; order the holder directly via Metav Werkzeuge or ask our consultants if needed. Parting clamp holder D028TM — right-hand parting holder, 3 mm cutting width (Teknik Makina) A Parting clamp holder D028TM designed for right-hand parting and grooving tasks on lathes, compatible with ZCC 3C ZT.D indexable inserts and optimised for short overhangs. Right-hand cutting direction 3 mm cutting width 18 mm maximum plunge depth Compatible with ZCC 3C ZT.D inserts Secure clamping for vibration-free parting The holder is engineered with a compact 20 x 20 mm shank and a solid clamp geometry that delivers high rigidity during cutting. This reduced overhang and firm clamping reduce vibration and tool deflection, which in turn improves surface finish and extends insert life. The compact footprint makes the tool ideal for tight setups where repeatability and process stability are decisive for productivity. Simple compatibility with standard inserts Acceptance of ZCC 3C ZT.D indexable inserts and the ISO 2020 seat designation ensures rapid sourcing and straightforward plate changes. The clamping concept permits fast replacement of worn inserts, reducing downtime during batch production. For operations that require consistent parting width and quick set-up, this compatibility translates directly into lower cycle times and easier tool management in the workshop. Geometry matched to typical lathe operations With an overall length of 125 mm and a maximum plunge depth of 18 mm, the holder suits most turning and parting applications where shallow to moderate cut depths are required. The specified 3 mm cutting width offers a balance between chip control and material removal rate for steel and common alloys; the right-hand orientation aligns with standard lathe feed directions, simplifying toolpath planning and operator routines. Production benefits for workshop and small-series machining In a production environment, consistent clamping and predictable insert seating reduce scrap and rework. The holder’s mass (approx. 0.394 kg) and compact dimensions support quick tool changes and stable cutting conditions on both manual and CNC lathes. Choosing this holder helps to maintain steady cycle times and supports quality assurance measures by keeping dimensional variation within tight tolerances. For supply and application advice on this Teknik Cutting Tools holder, contact Metav Werkzeuge in Emmerich for tailored recommendations and current availability via info@metav-werkzeuge.com or +49 2822 7131930 Technical data Article number: D028TM Manufacturer: Teknik Makina Designation: Parting clamp holder Facts Cutting width: 3 mm Maximum plunge depth: 18 mm Shank height x width: 20 x 20 mm Head width: 20 mm Overall length: 125 mm Weight: 0.394 kg Cutting direction: right Special features Compatible with ZCC 3C ZT.D inserts ISO designation: 2020 Tool bar designation: 3C-R ZT-D Designed for indexable insert parting operations FAQ Which inserts are compatible with this holder? The holder accepts ZCC 3C ZT.D indexable inserts with an ISO 2020 seat; these inserts are recommended for reliable clamping and correct seating in the Parting clamp holder D028TM. What is the maximum plunge depth for this holder? The maximum plunge depth is 18 mm, which allows controlled parting and grooving while maintaining stability with the 20 x 20 mm shank. Is the cutting direction left or right? This tool is specified for right-hand cutting; the right-hand orientation matches standard lathe feed directions for conventional setups. What are the overall length and shank size? Overall length is 125 mm and the shank measures 20 x 20 mm, providing a compact solution for short overhangs and reduced vibration. How straightforward is insert replacement? Insert replacement is quick thanks to the clamp design and ISO 2020 compatibility; the arrangement supports fast, repeatable seating for efficient maintenance of cutting edges. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
125mm Stechklemmhalter 3mm Cutting Width, 19mm Max Stechdepth, ISO 2020, 3C-123 SDV-R, For Sandvik Inserts, Right-Hand Cutting - Teknik Makina
Benefit from a compact, rigid right‑hand parting tool holder that combines a 3 mm cutting width with a 19 mm maximum cutting depth for reliable, repeatable parting operations; order directly via Metav Werkzeuge or consult the team for tailored technical advice. Stechklemmhalter / Parting Tool Holder — Right‑hand, 3 mm cutting width — Teknik Makina A Stechklemmhalter designed for precise right‑hand parting and grooving on CNC lathes, compatible with Sandvik indexable inserts and intended for repeatable production use Right-hand parting tool holder 3 mm cutting width for narrow grooves 19 mm max cutting depth Compatible with Sandvik inserts Precision and rigidity for predictable cuts The holder is engineered with a 20 x 20 mm shank and a 125 mm overall length to deliver stiffness at the cutting edge, which reduces chatter and improves surface finish. The ISO 2020 designation denotes a standardised shank and head geometry, simplifying toolholder selection for existing tool posts. At 0.397 kg the component balances mass for stability without excessive overhang, helping to maintain concentricity and extend insert life. This structural consistency supports high first‑pass accuracy and reduces rework in batch production. Optimised for narrow grooves and secure chip control With a 3 mm cutting width and a 19 mm max cutting depth, the holder suits fine parting and internal grooving tasks where material clearance and chip evacuation are critical. The right‑hand cutting direction ensures correct chip flow on machines set up for conventional turning to the right. Compatibility with Sandvik indexable inserts offers access to proven grades and geometries for steels, stainless materials and non-ferrous metals, enabling consistent cutting forces and easier process tuning. This combination of narrow kerf and controlled depth aids productivity on small to medium‑diameter workpieces. Fast clamping, repeatable set‑up and reduced downtime The clamping bar designation 3C‑123 SDV‑R indicates the bar interface and fitment, supporting secure insert retention and simple replacement procedures to limit machine downtime. The toolholder’s top features encourage quick set‑up on standard tool posts and predictable repeatability across shifts, which benefits lean manufacturing and small‑batch production runs. For customers uncertain about insert grade or machine compatibility, technical guidance is available to match the holder with the correct insert geometry and cutting parameters. The result is less trial‑and‑error, more consistent tool life and measurable process stability. For reliable parting and grooving with Teknik Makina quality, contact Metav Werkzeuge for personalised technical advice and fast supply — Metav Werkzeuge GmbH in Emmerich is available by e‑mail at info@metav-werkzeuge.com or by phone on +49 2822 7131930 Technical Data Article number: D904TM Manufacturer: Teknik Makina Product name: Stechklemmhalter Item designation (ISO): 2020 Compatible inserts: Sandvik Dimensions & weight Overall length: 125 mm Shank width: 20 mm Head width: 20 mm Shank height: 20 mm Cutting width: 3 mm Max cutting depth: 19 mm Weight: 0.397 kg Features & compatibility Cutting direction: right-hand Clamping bar designation: 3C-123 SDV-R ISO designation: 2020 Suitable for indexable inserts by Sandvik FAQ Which inserts fit this holder? The Stechklemmhalter from Teknik Makina (SKU D904TM) accepts indexable inserts compatible with Sandvik standards; matching insert geometry and grade will depend on the workpiece material and the intended cut depth. Is the holder suitable for use on CNC lathes? Yes — the parting tool holder is designed for CNC lathes and turret tool posts; the 125 mm overall length and 20 x 20 mm shank make it suitable for standard toolpost clamping arrangements. What is the maximum recommended cutting depth? The maximum cutting depth is 19 mm, which is intended for controlled parting and grooving operations where chip clearance and rigidity are critical. Can this holder be used for internal grooving? The holder’s 3 mm cutting width and right‑hand cutting direction make it suitable for narrow groove and parting applications; internal grooving is feasible where machine and turret clearances permit. How does the clamping system affect set‑up time? The clamping bar designation 3C‑123 SDV‑R ensures consistent insert seating and quick replacement, reducing set‑up time and improving repeatability for serial production. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
125mm Stechklemmhalter 3° 1212 3C-DGM 3 For 3C DGM 3 Innenkühlung Rechtsschneidend - Teknik Makina
The compact design combines a 12 x 12 mm clamping cross-section with a narrow 3 mm cutting width to deliver consistent parting accuracy and low-vibration performance; with a 125 mm overall length and a mass of 0.168 kg the toolholder supports rapid spindle response and repeatable results. Order the parting tool holder directly via Metav Werkzeuge or consult their application specialists for fitment advice. Parting tool holder – 12 x 12 mm clamping, 125 mm overall length | Teknik Makina A parting tool holder engineered for precise cut-off and grooving on lathes, compatible with 3C DGM 3 indexable inserts and designed to provide stable clamping and controlled plunging in standard turning setups. Precise 3 mm cutting width 12 x 12 mm clamping dimensions 125 mm overall length for stability Compatible with 3C DGM 3 inserts Stable, precise cut-off with minimal vibration The holder is tailored for demanding parting tasks where precision and repeatability are required. With a defined 3 mm cutting width, the system limits unnecessary material removal and helps achieve consistent component diameters; the narrow kerf reduces cutting forces and therefore vibration. Compatibility with 3C DGM 3 inserts simplifies tooling logistics, since replacement inserts are industry standard. This design leads to improved surface finish and reduced rework, making it suitable for batch production and workshop jobs where process stability matters. Secure clamping that enhances tool life and repeatability Clamping dimensions of 12 x 12 mm and an ISO-style designation (1212) provide a compact yet rigid interface that resists deflection under load. The 125 mm overall length contributes to an optimised overhang that balances accessibility and rigidity, while the low mass of 0.168 kg reduces inertial forces during rapid movements. As a result, cutting-edge wear on the insert is reduced and repeatability between cycles is improved. For engineers evaluating fixture dynamics, the controlled geometry translates directly into predictable machining behaviour and longer usable insert life. Designed for straightforward integration and reliable plunging Intended for parting and grooving operations, the toolholder accepts the 3C-DGM 3 tool shank and allows a maximum plunging depth of 16 mm, which covers common cut-off depths in small to medium components. The compact form factor eases integration into existing toolposts and turrets without extensive modification of the setup. Because the clamping mechanism is simple and robust, set-up times are shortened and alignment can be maintained across repeated insert changes. This combination of features supports efficient cycle planning and helps maintain production throughput. Contact Metav Werkzeuge to discuss integrating the Teknik Makina parting tool holder D847TM into the workflow and to receive precise application guidance from their Emmerich-based specialists Technical data Article number: D847TM Manufacturer: Teknik Makina Dimensions and weights Overall length: 125 mm Clamping height: 12 mm Cutting head width: 12 mm Holder width: 12 mm Cutting width: 3 mm Maximum plunging depth: 16 mm Weight: 0.168 kg Compatibility and features Compatible with inserts: 3C DGM 3 ISO designation: 1212 Toolholder shank reference: 3C-DGM 3 Intended for parting/grooving operations FAQ What insert type fits this holder and how is it designated? The parting tool holder from Teknik Makina accepts 3C DGM 3 indexable inserts; the holder is matched to that insert family and referenced as SKU D847TM for ordering. What are the clamping dimensions and why do they matter? Clamping dimensions are 12 x 12 mm, which give a compact, rigid interface; these dimensions influence deflection, repeatability and are quoted for the Teknik Makina parting tool holder (D847TM). How deep can this holder plunge during parting operations? Maximum plunging depth is 16 mm, which is suitable for standard cut-off depths encountered in general turning and grooving applications using the Teknik Makina D847TM. Is the holder suitable for quick insert changes in a production environment? Yes, the design supports straightforward insert replacement and stable reclamping, enabling efficient changeover and consistent machining with the Teknik Makina parting tool holder D847TM. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com
125mm Stechklemmhalter 3° 1616 3C-R MGM For 3C MGM Innenkühlung Rechtsschneidend - Teknik Makina
Take advantage of a narrow 3 mm cutting width and a right-hand orientation for controlled, efficient parting operations; the compact 16 mm head and 125 mm overall length ensure simple integration into existing tool setups. Order the parting tool holder directly via Metav Werkzeuge or ask their consultants for compatibility advice. Parting Tool Holder D668TM – right-hand holder with 3 mm cut width (Teknik Makina) A Parting Tool Holder D668TM designed for precise right-hand parting and cut-off work, compatible with Korloy 3C MGM indexable inserts and suited to compact lathe tool posts. Right-hand cutting direction 3 mm cutting blade width Compatible with Korloy 3C MGM inserts 125 mm overall length Precise parting performance for reliable cycle times The holder delivers consistent results for repetitive cut-off tasks thanks to its 3 mm kerf, which reduces material waste and minimises cutting forces compared with wider parting tools. The right-hand orientation and secure clamping system ensure that the insert is held steadily during each pass, reducing chatter and improving surface quality. Where throughput matters, the combination of a narrow cutting width and a stable mount helps to shorten cycle times while maintaining repeatable accuracy across batches. Designed for straightforward integration and fast tool changes With a 16 mm head width and an ISO-style designation 1616, the unit fits common tool posts and jigs without extensive modification. The holder accepts 3C MGM indexable inserts and the associated 3C-R MGM clamp-bar designation, which makes insert sourcing and replacement straightforward. The modest 125 mm overall length keeps overhang to a minimum, supporting rigidity at the cut edge and simplifying setup on existing machining centres or lathes. Built for workshop durability and predictable handling At just 0.268 kg, the holder is light enough for quick handling yet engineered to withstand standard workshop use. The maximum parting depth of 18 mm permits typical small to medium section removals, while the compact form factor reduces the risk of collision in constrained setups. The robust clamping geometry helps preserve insert life and supports consistent chip control, promoting operational reliability across long production runs. Practical guidance for application and compatibility Use the tool holder where narrow kerfs and controlled chip evacuation are required, for example in small-diameter bar work or when minimising material loss is a priority. The holder’s compatibility with Korloy 3C MGM inserts makes it a pragmatic choice for shops standardising on that insert family. For unfamiliar set-ups, verify toolpost clearance and ensure correct right-hand orientation before cutting; the short overhang and secure clamp bar typically simplify alignment and reduce setup time. For supply and technical guidance on the Teknik Cutting Tools parting tool holder D668TM, contact Metav Werkzeuge in Emmerich — email info@metav-werkzeuge.com or call +49 2822 7131930 to discuss fitment and order details. Technical Data Article number: D668TM Manufacturer: Teknik Makina Product: Parting tool holder ECLASS: 21181005 SKU: D668TM Cutting width: 3 mm Holder head width: 16 mm Maximum parting depth: 18 mm Overall length: 125 mm Weight: 0.268 kg Right-hand cutting direction Compatible with Korloy 3C MGM indexable inserts ISO designation: 1616 Holder bar designation: 3C-R MGM Suitable for 3C MGM inserts FAQ What insert type fits this holder? The holder accepts Korloy 3C MGM indexable inserts; the clamp-bar designation 3C-R MGM is used for secure seating and fast replacement. What is the maximum parting depth? Maximum parting depth is 18 mm, suitable for typical small to medium section parting tasks. Is the cutting direction right-hand or left-hand? This unit is configured for right-hand cutting and should be mounted accordingly for correct chip flow and tool orientation. What are the key dimensions for setup? Key dimensions include a 16 mm head width and 125 mm overall length, which help determine clearance and toolpost compatibility. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
125mm Stechklemmhalter 3° 2020 3C-R DGN For 3C DGN Innenkühlung Rechtsschneidend - Teknik Makina
Benefit from a compact, right‑hand parting solution that combines a 3 mm cutting width with a secure clamp design and a 20 mm maximum plunge depth. The result is predictable chip control and reduced vibration for stable parting operations — order the parting clamp holder directly via Metav Werkzeuge or ask our consultants for application advice. Parting and Grooving Tool Holder D762TM (Teknik Makina) — right‑hand, 3 mm cutting width The Parting and Grooving Tool Holder D762TM is a right‑hand clamp holder designed for precise parting and grooving with ISO 2020 / 3C DGN inserts in production and workshop turning applications Right-hand cutting orientation Compatible with ISCAR 3C DGN inserts 3 mm cutting width for fine parting 125 mm overall length for improved rigidity Precision and stable cutting for consistent results The compact design of this tool holder focuses on delivering precision and stability during parting operations. With a 3 mm cutting width and a maximum plunge capability of 20 mm, the holder is suited to fine cut‑off tasks where accurate depth control is required. The 20 x 20 mm clamp profile and 125 mm overall length reduce tool overhang and increase rigidity, which diminishes chatter and leads to improved surface quality and closer tolerances. Technical terms such as ISO 2020 refer to the insert footprint and ensure straightforward insert replacement and predictable cutting geometry. Easy integration into existing insert systems and quick handling Compatibility is engineered in: the holder accepts 3C DGN inserts from major manufacturers, notably ISCAR, and matches the shank designation 3C‑R DGN, which eases retrofit into standard tool posts. The right‑hand cutting orientation is optimised for conventional lathes and CNC turning centres. At approximately 0.394 kg, the holder is light enough for fast manual handling yet substantial enough to keep a secure clamping force during operations. The combination of known ISO sizing and a recognised shank designation simplifies inventory management and reduces set‑up time on the shop floor. Dependable clamping, repeatability and workshop advantages Designed for robust clamping, the holder secures the insert firmly to prevent micro‑movement that can shorten insert life or cause inconsistent part dimensions. Improved repeatability translates directly into fewer rejects and less rework, supporting higher overall equipment effectiveness. For production environments the predictable behaviour of the holder under load reduces process variation and contributes to lower operating costs through extended insert performance and fewer machine stops. The result is a practical, long‑term benefit to throughput and part quality. For tailored application advice or to arrange supply from Metav Werkzeuge in Emmerich, contact our consultants at info@metav-werkzeuge.com or call +49 2822 7131930 — ask about the Teknik Makina D762TM parting clamp holder and its suitability for specific turning tasks Technical Data Article number: D762TM Manufacturer: Teknik Makina Facts Overall length: 125 mm Clamp height: 20 mm Clamp width: 20 mm Cutting head width: 20 mm Cutting width: 3 mm Max plunge depth: 20 mm Weight: 0.394 kg Cutting direction: right Compatibility & Features Compatible inserts: 3C DGN Inserts manufacturer: ISCAR ISO designation: 2020 Shank designation: 3C‑R DGN Right‑hand parting tool holder FAQ Which inserts fit this holder? The holder is specified for 3C DGN inserts and is compatible with inserts from ISCAR; the ISO 2020 footprint determines the correct insert size. Is the cutting orientation right‑hand or left‑hand? This model is a right‑hand parting and grooving holder, designed for conventional right‑hand cutting directions. What is the maximum plunge depth for the holder? The maximum plunge depth is 20 mm, which suits typical parting and grooving operations requiring controlled engagement. Which shank or mounting designation does it use? Mounting follows the 3C‑R DGN shank designation and the holder corresponds to the ISO 2020 insert format for straightforward integration. How does the holder support repeatable results in the workshop? With a compact 125 mm overall length and a firm 20 x 20 mm clamp profile, the design reduces overhang and vibration, supporting repeatable cuts and reduced scrap Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com
125mm Stechklemmhalter 3° 2020 3C-R MGM For 3C MGM Innenkühlung Rechtsschneidend - Teknik Makina
Benefit from precise, repeatable parting operations thanks to the combination of a 20 mm head width and a 3 mm cutting width; the right-hand design with an 18 mm maximum plunge depth provides secure, efficient machining. Order the parting tool holder directly via Metav Werkzeuge or consult our advisers for application-specific guidance. Parting tool holder D670TM — right-hand design, 20 mm head, 3 mm cutting width (Teknik Makina) Parting tool holder D670TM performs fine parting and grooving tasks on lathes and turning centres, accepting Korloy 3C MGM indexable inserts for a compact, rigid setup. 20 mm head width for stable seating 3 mm cutting width for precise parting Compatible with Korloy 3C MGM inserts Right-hand cutting, 125 mm overall length Precision parting that maintains process stability The holder is engineered for controlled separation operations where repeatability matters. With a 3 mm cutting width and 18 mm max plunge depth, the geometry minimises chatter and promotes consistent chip formation; this results in fewer re-cuts and lower scrap rates. The compact head contributes to rigidity, while the right-hand cutting orientation ensures conformity with standard lathe setups. These characteristics translate into measurable cycle-time improvements and dependable component quality for serial and single-part work. Straightforward compatibility and reduced tool inventory Equipped to accept Korloy 3C MGM inserts and specified for an ISO 2020 shank form, the holder simplifies tool selection and changeover. The overall length of 125 mm and modest mass of 0.407 kg allow straightforward mounting without undue overhang, helping to preserve tool life and workpiece finish. By matching common insert formats, the system reduces the number of specialised spares required, so workshop stocking becomes more efficient and predictable. Robust clamping and consistent cutting behaviour A secure clamping concept provides stable clamping and repeatable seating of indexable inserts; this reliability supports uniform cutting forces and diminishes variation between cycles. The holder’s design concentrates stability where it matters most, reducing the risk of vibration-induced surface defects. The result is a predictable machining process that aids quality assurance and contributes to overall production reliability and operator confidence. Practical application and workshop integration Ideal for parting-off and grooving operations on conventional and CNC lathes, the tool holder suits short-run production and precision rework alike. Its compatibility with widely used insert geometries makes it a practical choice where quick insert changes and predictable outcomes are priorities. If selection between tool variants is unclear, Metav’s product advisers can provide tailored recommendations based on machining parameters and insert grades to match the intended application without overspecifying equipment or stock. For purchasing or detailed advice on the D670TM parting tool holder, contact Metav Werkzeuge for technical consultation and order processing: info@metav-werkzeuge.com or +49 2822 7131930 Technical data Article number: D670TM Manufacturer: Teknik Makina Product: Parting tool holder Key figures Head width: 20 mm Cutting width: 3 mm Maximum plunge depth: 18 mm Overall length: 125 mm Weight: 0.407 kg Special features Compatible with Korloy 3C MGM inserts ISO 2020 shank designation Boarstang designation: 3C-R MGM Right-hand cutting direction FAQ Which inserts are compatible with the parting tool holder D670TM? The D670TM accepts Korloy 3C MGM indexable inserts; these inserts fit the holder geometry and enable standardised re-grading and replacement. What is the maximum plunge depth for this holder? The parting tool holder D670TM provides a maximum plunge depth of 18 mm for secure parting operations. Which cutting direction does the D670TM support? This holder is specified for right-hand cutting to suit conventional lathe arrangements and corresponding insert geometries. What are the shank and size specifications of the D670TM? The D670TM is designed to ISO 2020 shank form, with an overall length of 125 mm and a weight of 0.407 kg. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com
125mm Stechklemmhalter 3°? 1616 3C-L DGN For 3C DGN Innenkühlung Linksschneidend - Teknik Makina
This parting and grooving solution combines robust clamping with standardised dimensions for reliable, repeatable cuts — the 16 x 16 mm shank (ISO 1616) and 3 mm cutting width deliver consistent results while the left-hand configuration suits common lathe setups; order via Metav Werkzeuge or ask our consultants for application-specific guidance. Parting and Grooving Tool Holder D731TM — 16 x 16 mm shank, left-hand, Teknik Makina The Parting and Grooving Tool Holder D731TM is a left-hand insert holder designed for precision parting and grooving tasks on CNC lathes, compatible with 3C DGN indexable inserts for standard industrial production 16 x 16 mm shank, ISO 1616 Compatible with 3C DGN inserts (ISCAR) Left-hand cutting direction, 3 mm blade width 125 mm overall length, max 19 mm cutting depth Solid shank and repeatable set-up for precise cuts A compact, rigid design provides a stable platform for narrow grooving and parting operations. The 16 x 16 mm shank and ISO 1616 designation ensure compatibility with common toolposts and quick mounting on turret stations. This dimensional standardisation reduces set-up time and improves repeatability, which is essential where consistent part geometry is required. The holder’s construction concentrates clamping force around the insert pocket to limit vibration and maintain a predictable cutting line. Compatibility that simplifies tooling logistics Built for use with 3C DGN indexable inserts and matched to major insert makers such as ISCAR, the holder lowers stock complexity by accepting widely available inserts. The modest 3 mm cutting width and a maximum 19 mm cutting depth suit routine parting and light grooving tasks, allowing controlled chip formation and easy chip evacuation. The left-hand cutting direction is specified for operations on setups where the tool must enter from the workpiece right side, providing a clean, predictable chip flow and reduced rework. Practical handling and workshop efficiency With an overall length of 125 mm and a lightweight construction of 0.253 kg, the tool holder is easy to position and clamp while remaining rigid during cutting. The clamping mechanism secures the insert securely, enabling short changeover times and stable cutting performance across production runs. For small-batch or repair work, the compact footprint helps to avoid collisions and keeps the toolpath close to the machine centre, supporting safe single-setup machining without excess overhang. Typical applications and support for industrial use The holder is tailored for precision parting-off, narrow groove profiling and short-face grooving on shafts and turned components. It performs well in series production and job-shop environments where consistent slot widths and clean part separation matter. For advice on integration into existing tooling systems or confirmation of insert interchangeability, Metav Werkzeuge provides application guidance and can assist with selection of compatible inserts and fastening hardware. Choose the Teknik Cutting Tools D731TM holder for precise, standardised parting performance and contact Metav Werkzeuge for tailored application advice and reliable supply: info@metav-werkzeuge.com or +49 2822 7131930 Technical data Article number: D731TM Manufacturer: Teknik Makina Compatible inserts: 3C DGN Compatible insert maker: ISCAR ISO designation: 1616 Facts Overall length: 125 mm Shank width: 16 mm Shank height: 16 mm Cutting head width: 16 mm Cutting width: 3 mm Max cutting depth: 19 mm Weight: 0.253 kg Special features Left-hand cutting direction Bore bar designation: 3C-L DGN Designed for parting and grooving inserts Standardised 16 x 16 mm shank (ISO 1616) FAQ Which inserts are compatible with this holder? The D731TM accepts 3C DGN indexable inserts; inserts from major makers such as ISCAR fit the pocket geometry and secure clamping. Is this holder left or right cutting? This tool holder is specified for left-hand cutting, suitable for set-ups where the tool enters the workpiece from the right. What cutting width and depth are possible with the holder? The holder supports a 3 mm cutting width with a maximum parting/grooving depth of 19 mm. What are the shank dimensions and overall length? Shank dimensions are 16 x 16 mm (ISO 1616) and the overall length is 125 mm, compatible with standard 16 mm toolposts. Is the D731TM suitable for heavy roughing operations? The D731TM is optimised for precision parting and narrow grooving; its design emphasises rigidity and control rather than heavy-material stock removal Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com
125mm Stechklemmhalter 4mm Cut Width, 18mm Max Plunge, ISO 2020, Fits 4C MGM Inserts, 4C-L MGM Shank, Left-Hand Cutting, Internal Cooling - Teknik Makina
Combine the 4 mm cutting width with the compact 20 × 20 mm shank and 125 mm overall length to achieve stable, repeatable grooving operations; the left‑hand orientation and compatibility with Korloy 4C MGM inserts simplify tool selection. Order directly via Metav Werkzeuge or consult our specialists for application guidance. Grooving clamping holder D617TM — left‑hand grooving toolholder with 20 × 20 mm shank (Teknik Cutting Tools) A grooving clamping holder designed for left‑hand turning operations, offering a narrow 4 mm cutting width and an ISO 2020 shank for consistent mounting in compact toolposts 20 × 20 mm shank for secure clamping 4 mm cutting width for narrow grooves Left‑hand cutting direction for specific turning setups Compatible with Korloy 4C MGM inserts Accurate grooves from a compact shank The compact 20 × 20 mm shank and the ISO 2020 designation provide a familiar fitment for standard toolposts, reducing setup time and minimising run‑out. A smaller shank cross‑section concentrates rigidity where it matters, delivering consistent contact between holder and lathe. This stability translates into predictable groove geometry and reduced rework, making the holder especially suitable for small‑batch production and precision workshop use. Controlled narrow cuts and secure plunge capacity With a 4 mm cutting width and a maximum plunge depth of 18 mm, the holder is optimised for fine grooving and parting‑off operations that require controlled chip evacuation and minimal material disturbance. The left‑hand cutting orientation aligns with turning setups where tool approach from the left is required; this detail avoids guesswork during toolpath planning. In practical terms, the maximum plunge depth indicates the effective vertical reach of the cutting edge into the workpiece, helping to prevent overloads and maintain surface quality. System compatibility that speeds up changeovers Designed to accept Korloy 4C MGM inserts and to pair with the 4C‑L MGM bar designation, the toolholder integrates with common insert families to reduce inventory complexity. The overall length of 125 mm and a weight of 0.407 kg keep the assembly compact and simple to handle, while reliable clamping geometry ensures repeatable indexability of inserts. For workshops seeking efficiency, this combination lowers tooling downtime and supports a clear tooling strategy using well‑known insert standards. Contact Metav Werkzeuge for tailored application advice on the Teknik Cutting Tools grooving clamping holder D617TM and secure precise recommendations from our Emmerich specialists Technical data SKU: D617TM Manufacturer: Teknik Makina Designation: Grooving clamping holder Dimensions & core data Shank height: 20 mm Shank width: 20 mm Cutting width: 4 mm Max plunge depth: 18 mm Overall length: 125 mm Weight: 0.407 kg Cutting direction: Left Compatibility & features For inserts: 4C MGM Compatible insert maker: Korloy Shank ISO designation: 2020 Toolholder bar designation: 4C‑L MGM Left‑hand grooving orientation FAQ What insert types fit this grooving holder? The grooving clamping holder D617TM is designed for Korloy 4C MGM inserts and other inserts in the 4C MGM family, ensuring straightforward interchangeability on compatible turning centres. Is the holder suitable for deep grooving tasks? The holder supports a maximum plunge depth of 18 mm, which makes the D617TM appropriate for controlled, moderate‑depth grooving rather than heavy deep‑cut applications. Which shank size does the toolholder require in the toolpost? This toolholder features a 20 × 20 mm shank (ISO 2020), providing a standardised fit for toolposts accepting that shank cross‑section and promoting low run‑out. Can the D617TM be used for parting‑off as well as grooving? Yes—its 4 mm cutting width and secure clamping make the D617TM suitable for fine parting‑off and precision grooving where narrow cuts are required. What advantages does the left‑hand orientation offer? The left‑hand cutting direction of this holder aligns with turning setups that require tool approach from the left, simplifying toolpaths and improving process repeatability when that orientation is specified. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com
125mm Stechklemmhalter 4mm Cutting Width, 18mm Max Stech Depth, 20mm Holder Width, 20mm Head Width, 20mm Holder Height, For 4C ZT.D Indexable Inserts, 4C-R ZT-D Shank, Right-Hand Cutting - Teknik Makina
Take advantage of a compact, stable holder that delivers precise 4 mm parting and grooving action with a 20 × 20 mm shank profile for standard toolposts. Combine predictable chip control and a 125 mm reach to maintain steady production—order directly via Metav Werkzeuge or consult the team for application advice. Stechklemmhalter – Right-hand grooving and parting tool holder, 4 mm cutting width The Stechklemmhalter is a right-hand grooving and parting tool holder engineered for indexable inserts, designed to perform controlled slotting and cut-off operations in workshop and light industrial turning applications. Right-hand cut, 4 mm cutting width 20 × 20 mm shank for standard toolposts Compatible with ZCC 4C ZT.D indexable insert Robust 125 mm length, 0.4 kg for stable cutting Precision where every millimetre counts The holder offers a defined 4 mm cutting edge width that supports repeatable parting and grooving cycles. Its compact 20 × 20 mm shank provides compatibility with common toolposts and reduces vibration at the cutting point; the result is improved surface quality and longer insert life. The design concentrates on predictable chip formation and secure clamping, which are decisive for maintaining cycle times in batch production and reducing rework. Built for firm clamping and stable cutting A low mass of 0.4 kg and a 125 mm overall length deliver a balance between accessibility and rigidity. The clamping geometry secures the insert carrier for reliable contact force, which translates into consistent dimensional control during slotting tasks. Where tool stability matters, the holder’s proportions minimise chatter and support smoother entry and exit during parting operations, helping to protect both the workpiece and the indexable insert. Compatibility and straightforward integration Designed for use with ZCC 4C ZT.D indexable inserts and identified by the ISO-style designation 2020, the holder adapts to widely available insert systems. The bar designation 4C‑R ZT‑D indicates the compatible boring bar profile and facilitates replacement or system matching in existing tool setups. Right-hand orientation suits standard turning centres configured for conventional feed direction and is easily identified during tool set-up. Application guidance for workshops and production This grooving and parting holder is intended for general turning environments where tight control of groove width and depth is required. The specified maximum plunge depth of 18 mm enables secure single‑pass operations in many common components, while the controlled cutting width reduces the need for multiple finishing passes. For efficient set-up, pair the holder with inserts from the recommended range and verify seat alignment to maintain repeatable results. For reliable supply and expert advice on selecting the correct Teknik Makina grooving and parting holder (SKU D036TM) for a specific machine or application, contact Metav Werkzeuge directly at +49 2822 7131930 or info@metav-werkzeuge.com to discuss suitability and lead times. Technical Data Article number: D036TM Manufacturer: Teknik Makina Facts Weight: 0.4 kg Overall length: 125 mm Shank height: 20 mm Shank width: 20 mm Cutting width: 4 mm Maximum plunge depth: 18 mm Special features Compatible with ZCC 4C ZT.D indexable insert ISO designation: 2020 Bar designation: 4C-R ZT-D Cutting direction: right Intended use: grooving and parting operations FAQ What insert series fits this grooving holder? The holder accepts the ZCC insert specified as 4C ZT.D, matching the ISO-style 2020 seat; use inserts with the corresponding geometry for correct seating and clamping. What is the maximum cutting depth for single-pass parting? The maximum plunge depth is 18 mm, which allows secure single‑pass engagement for appropriate workpiece diameters and materials when combined with the correct insert grade. Will the holder fit a standard 20 mm toolpost? Yes, the 20 × 20 mm shank dimensions are suitable for standard 20 mm toolpost slots and support rigid mounting for grooving and parting tasks. Is this a right-hand or left-hand tool holder? This item is a right-hand grooving and parting holder, designed for conventional feed directions on standard turning machines. Manufacturer / Responsible: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com
125mm Stechklemmhalter 4mm Cutting Width, Max 18mm Depth, Left-Hand Cutting, ISO 2020, Compatible With Sandvik Inserts, 20mm Shank Height - Teknik Makina
Benefit from a compact, high-rigidity design that combines secure clamping and precise parting: the left-hand configuration with a 4 mm cutting width and a maximum plunge depth of 18 mm enables controlled cut-off operations with standard Sandvik inserts. Order via Metav Werkzeuge or consult the technical team for machine-specific matching. Cut-off Insert Holder D877TM — Left-hand parting holder, 4 mm cut width by Teknik Makina A robust Cut-off Insert Holder engineered for left-hand parting tasks, compatible with Sandvik ISO 2020 indexable inserts and suitable for compact turning setups. Left-hand cutting direction 4 mm parting width for narrow cuts Compatible with Sandvik ISO 2020 inserts Compact 20 x 20 mm shank profile Precision parting with controlled depth and stability The Cut-off Insert Holder delivers repeatable parting performance through a rigid shank and a defined plunge capacity. The left-hand cutting orientation is optimised for operations where tool approach from the left is required, while the 4 mm cutting width allows narrow, accurate separations with minimal material waste. A maximum plunge depth of 18 mm is specified, which defines the greatest single pass engagement; this figure is decisive when planning cycle times and tool engagement strategies. By reducing chatter and maintaining a constant cutting line, the holder supports consistent surface finishes and fewer secondary operations. Streamlined inventory and assured compatibility with standard inserts Compatibility with Sandvik 2020 inserts (ISO 2020) simplifies procurement and reduces tool inventory complexity. The holder accepts widely used insert formats, enabling shops to standardise on a single grade and geometry for multiple machines. The compact shank profile of 20 x 20 mm and an overall length of 125 mm make the tool easy to fit in tight tool posts and automated tool changers; the moderate mass of 0.415 kg contributes to stable dynamics without overloading lighter turrets. These characteristics help to lower set-up time and improve process reliability across repetitive parting operations. Secure clamping and workshop practicality for reliable production Designed for repeatability, the device provides secure clamping for indexable cutting edges and is identified by the ISO designation 2020, which clarifies compatible insert geometries. The indicated bar-holder designation 4C-123 SDV-L aligns the component with common CNC turning stocks and spindle orientations. The holder’s dimensions and mass balance have been selected to ease handling during set-up while preserving the stiffness necessary for interrupted cuts. Routine maintenance is kept straightforward through accessible clamping screws and standard insert fixation, reducing downtime and supporting continuous throughput in busy workshops. Contact Metav Werkzeuge for tailored advice and fast supply from Emmerich — quote SKU D877TM to confirm machine compatibility and delivery options Technical data Article number: D877TM Manufacturer: Teknik Makina Product: Cut-off insert holder Facts Overall length: 125 mm Shank width: 20 mm Head width: 20 mm Holder height: 20 mm Cutting width: 4 mm Maximum plunge depth: 18 mm Weight: 0.415 kg Special features Compatible with Sandvik inserts (ISO 2020) Left-hand cutting direction Bar-holder designation: 4C-123 SDV-L ISO designation: 2020 FAQ What insert types fit this holder? The holder accepts Sandvik indexable inserts conforming to the ISO 2020 designation; use inserts matched to that geometry for correct seating and performance. Is the cutting direction fixed? Yes — the tool is supplied for left-hand cutting, making it suitable for operations requiring a left-handed approach. What is the maximum depth of cut for single-pass parting? The maximum plunge depth is 18 mm, which should be considered when planning single-pass or stepped parting strategies. Will this holder fit compact tool posts? With a shank profile of 20 x 20 mm and an overall length of 125 mm, the holder is intended for compact tool posts and constrained turret configurations. Which SKU should be referenced when ordering or checking compatibility? Reference SKU D877TM and the brand Teknik Makina when confirming compatibility or requesting documentation. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com
125mm Stechklemmhalter 4° 2020 4C-R TD For 4C TD Innenkühlung Rechtsschneidend - Teknik Makina
Benefit from a compact, reliable holder designed for narrow-parting operations: precise 4 mm cutting width combined with a maximum 18 mm parting depth enables consistent groove quality and reduced rework. The combination of ISO 2020 shank compatibility and a 125 mm overall length makes this an efficient choice for mixed production runs — order the parting tool holder directly via Metav Werkzeuge or consult our specialists for application advice. Parting tool holder D722TM — right-hand holder for narrow parting, Teknik Makina A parting tool holder D722TM designed for right-hand grooving and short overhang applications on CNC and turning centres Compact ISO 2020 shank 20 x 20 mm 4 mm cutting width for narrow grooves Compatible with Taegutec 4C TD inserts Max parting depth 18 mm for deeper cuts Precision fit and stable clamping for repeatable grooves The holder is built around an ISO 2020 shank and a compact 20 x 20 mm profile to ensure a rigid connection to the toolpost. This rigidity reduces chatter and maintains dimensional repeatability over long runs, so processes that require tight tolerances benefit from fewer scrapped parts. Compatibility with Taegutec 4C TD indexable inserts simplifies tooling procurement and supports standardised insert stock across the workshop. High-throughput turning with narrow-parting capability A cutting width of 4 mm combined with a maximum parting depth of 18 mm enables efficient material separation and grooving without excessive tool overhang. The holder’s 125 mm overall length balances reach and stiffness, while a modest mass of 0.401 kg helps to lower centrifugal loads at higher spindle speeds. These characteristics translate into shorter cycle times and more consistent surface finishes for repeat jobs and batch production. Compact design for quick setup and dependable service life The compact frame and straightforward clamping geometry minimise setup time and simplify insert changes, improving shop-floor productivity. Acceptance of the 4C-R TD clamping designation and the 2020 mounting standard means the holder integrates with common toolposts and fixtures, reducing the need for special adapters. The construction focuses on stable clamping and predictable behaviour, supporting sustained uptime in daily turning and grooving operations. Select the Teknik Makina D722TM parting tool holder for dependable right-hand grooving — contact Metav Werkzeuge for tailored advice and fast dispatch from Emmerich: info@metav-werkzeuge.com | +49 2822 7131930 Technical data Article number: D722TM Manufacturer: Teknik Makina Facts Cutting width: 4 mm Max cutting depth: 18 mm Overall length: 125 mm Weight: 0.401 kg Shank width: 20 mm Shank height: 20 mm Special features Compatible with Taegutec 4C TD inserts ISO 2020 shank designation 4C‑R TD clamping designation Right-hand cutting direction FAQ Is this holder compatible with Taegutec inserts? Yes. The parting tool holder D722TM is designed to accept Taegutec 4C TD indexable inserts, providing a standardised solution for insert changes and stock control. What shank size and mounting standard does the holder use? The D722TM features an ISO 2020 shank with a 20 x 20 mm profile, matching common toolposts for straightforward mounting in many turning applications. Is the D722TM suitable for left-hand grooving? No. This holder is specified for right-hand cutting direction and is optimised for right-hand parting and grooving operations as supplied. What are the maximum parting depth and cutting width? The holder supports a maximum parting depth of 18 mm and a cutting width of 4 mm, enabling narrow groove and parting tasks without excessive overhang. Can the D722TM be used on short overhang setups for high-speed turning? Yes. With a 125 mm overall length and a modest weight of 0.401 kg, the holder balances reach and stiffness for short overhang, higher-speed applications while maintaining stability. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com
125mm Stechklemmhalter 5mm Cut Width, 25mm Shank Width, 25mm Max Depth, 5C MGM For Indexable Inserts, Right-Hand Cutting, 2525 5C-R MGM Innenkühlung - Teknik Makina
Take advantage of a compact, stable holder that combines a 5 mm cutting width with a 25 mm maximum cutting depth for precise parting and grooving. Order the D682TM via Metav Werkzeuge or consult our specialists for application advice. Parting clamp holder D682TM – right-hand, 5 mm cutting width (Teknik Cutting Tools) A parting clamp holder designed for right-hand grooving and parting operations on conventional and CNC lathes, delivering stable clamping for narrow cuts. Right-hand cutting for standard lathes 5 mm cutting width for narrow grooves 25 mm maximum cutting depth Compatible with Korloy 5C MGM inserts Precision where narrow cuts matter This grooving tool holder is engineered to produce consistent, accurate parting cuts. The combination of a 5 mm cutting width and a 25 mm max cutting depth ensures controlled chip formation in confined grooves, reducing the risk of chatter. Right-hand cutting geometry provides reliable engagement for standard lathe set-ups, while the compact design helps maintain tool rigidity for repeatable results. Fast set-up and secure clamping for steady turning Set-up is straightforward thanks to the ISO 2525 shank (25 x 25 mm) and the compatible 5C-R MGM bar designation. The 125 mm overall length and modest 0.703 kg mass support a low-inertia arrangement that limits vibration and promotes longer insert life. Secure clamping of the Korloy 5C MGM insert family simplifies tool changes and keeps the cutting edge consistently positioned. Designed for dependable shop-floor performance Built for everyday workshop use, the holder focuses on practical efficiency: reduced downtime through quick insert swapping and robust contact between insert and clamping seat. The compact cutting-head width of 25 mm aids in access to tight features, while the proven right-hand orientation suits a broad range of turning tasks. For operations requiring narrow groove control and repeatability, this tool solution delivers measurable improvements in cycle stability and surface quality. Contact Metav Werkzeuge for tailored application guidance and reserve the Teknik Cutting Tools parting clamp holder D682TM to secure consistent grooving performance in production or prototype turning work Technical data Article number: D682TM Product name: Stechklemmhalter Manufacturer: Teknik Makina Numbers / Core technical data Total length: 125 mm Weight: 0.703 kg Cutting width: 5 mm Max cutting depth: 25 mm Cutting head width: 25 mm Design / Special features Cutting direction: right ISO shank designation: 2525 Boring-bar designation: 5C-R MGM Compatible with Korloy 5C MGM inserts FAQ Which insert style fits this holder? The holder accepts 5C MGM style inserts and is specified as compatible with Korloy 5C MGM grades for standard grooving operations. Is the D682TM suitable for CNC lathes? Yes, the D682TM parting clamp holder is suitable for both conventional and CNC lathes when used with the correct tool post and clamping arrangements. What does the ISO 2525 reference mean? ISO 2525 indicates a square shank profile of 25 x 25 mm, which determines the tool-post compatibility and ensures the holder seats correctly in standard tool blocks. How does the right-hand cutting direction affect set-up? Right-hand cutting means the insert is oriented for cuts made when the tool feeds from right to left relative to the workpiece rotation; set-up should reflect this orientation to achieve intended chip flow and surface finish. Can the holder reach deep grooves? The holder offers a maximum cutting depth of 25 mm, suitable for many parting and grooving tasks within that depth range, while maintaining rigidity and insert stability. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com
125mm Stechklemmhalter 5mm Cutting Width, 18mm Max Depth, ISO 2020, 5C-R ZT-D, Suitable For 5C ZT.D Inserts, Right-Hand Cutting - Teknik Makina
Combine robust clamping dimensions with a compact 125 mm length and a precise 5 mm cutting width to achieve reliable, repeatable parting operations. Benefit from right-hand orientation and ZCC insert compatibility for streamlined tool changes; order directly via Metav Werkzeuge or consult the technical team for integration advice. Parting tool clamping holder — right-hand, 5 mm cutting width (Teknik Makina) A parting tool clamping holder designed for right-hand parting and grooving, offering a compact 125 mm overall length and compatibility with ZCC 5C ZT.D indexable inserts. Right-hand orientation for controlled cuts 5 mm maximum cutting width 20 x 20 mm robust shank profile Compatible with ZCC 5C ZT.D inserts Precise parting performance for production turning The holder delivers consistent parting and grooving thanks to its 5 mm cutting width and right-hand cut geometry. The constrained cutting width reduces chip load and supports repeatable dimensional results when used in serial turning operations. With a compact overall length, the toolholder minimises overhang, which helps keep the cutting forces predictable and contributes to a stable machining process. This practical combination of geometry and size supports higher throughput without sacrificing workpiece quality. Stiff construction to limit vibration and improve surface finish Engineered with a 20 x 20 mm shank profile and a total length of 125 mm, the clamping device is balanced for rigidity in close-quarter operations. Reduced deflection from a short projection improves surface finish and tool life, especially in interrupted cutting typical of parting tasks. The unit’s 0.391 kg mass provides enough inertia to damp minor vibrations while remaining easy to fit into standard toolposts, which benefits workshop ergonomics and setup speed. Fast insert changes and proven insert compatibility Designed around the ISO-style designation 2020, the holder accepts ZCC indexable inserts (5C ZT.D), permitting quick insert replacement and predictable seating. The bores and clamping geometry are matched to the 5C-R ZT-D bar interface, enabling straightforward mounting on compatible shanks. Faster insert swaps reduce machine downtime and lower total cost per cut by keeping the tool assembly in service rather than out for lengthy adjustments. Practical guidance for workshop integration Prepared for right-hand parting with a maximum cutting depth of 18 mm, this clamping holder is suited to routine parting and shallow grooving tasks where compactness and repeatability matter. The simple clamping concept supports quick setup changes and keeps spare-part inventory predictable by using widely available ZCC insert types. For installations requiring specific mounting adapters, confirmation of the bar interface code ensures correct selection and fit. Contact Metav Werkzeuge to clarify compatibility, check stock in Emmerich and arrange a fast supply of the Teknik Cutting Tools parting tool clamping holder (SKU D044TM); telephone +49 2822 7131930 or email info@metav-werkzeuge.com Technical data Article number: D044TM Manufacturer: Teknik Makina SKU: D044TM Brand: Teknik Cutting Tools Dimensions & core figures Overall length: 125 mm Holder height: 20 mm Holder width: 20 mm Cutting width: 5 mm Maximum parting depth: 18 mm Weight: 0.391 kg Compatibility & features Compatible with ZCC / 5C ZT.D inserts ISO designation: 2020 Bar/shank designation: 5C-R ZT-D Cutting direction: right-hand FAQ What is the maximum cutting depth for this holder? The parting tool clamping holder (Teknik Makina, SKU D044TM) supports a maximum parting depth of 18 mm, suitable for standard grooving and parting operations. Which inserts fit this holder? This holder accepts ZCC indexable inserts marked 5C ZT.D and follows the ISO-style 2020 seating pattern for predictable insert location. Is the tool left- or right-hand oriented? The holder is configured for right-hand cutting and is intended for right-hand parting applications. What are the shank dimensions and overall length? The clamping unit features a 20 x 20 mm shank profile and an overall length of 125 mm for reduced overhang. Who supplies and supports this tool in Europe? Metav Werkzeuge supplies and supports the Teknik Cutting Tools parting tool clamping holder (D044TM) from its Emmerich location and can advise on compatibility and delivery. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com
125mm Stechklemmhalter 5mm Cutting Width, 18mm Max Stepping Depth, ISO 2020, 5C-R S224, For Horn Inserts, Right-Hand Cutting, Innenkühlung - Teknik Makina
Take advantage of a compact right‑hand parting holder that combines a 5 mm cutting width with a 20×20 mm standard shank for fast, repeatable parting operations; order directly via Metav Werkzeuge or consult our specialists for integration advice. Parting tool holder D708TM — right‑hand holder, 20×20 mm shank, 5 mm cutting width (Teknik Makina) The parting tool holder D708TM is a right‑hand clamping holder intended for standard lathe parting and grooving tasks where secure insert seating and compact tool geometry are required Right‑hand cutting orientation 20×20 mm standard shank size 5 mm parting blade width 18 mm maximum plunge depth Compatible with Horn ISO 2020 inserts Precise parting performance with defined cutting geometry The D708TM delivers consistent separation thanks to its 5 mm cutting width and a maximum plunge depth of 18 mm, which together support controlled chip formation and reliable chip evacuation. The holder’s right‑hand orientation matches common turning setups, ensuring the cutting forces are directed to the lathe bed and minimising vibration. For operators unfamiliar with parting terminology: a narrower cutting width reduces material engagement per pass, so fewer cutting forces are transferred into the workpiece and the machine, improving dimensional stability and surface finish. Quick integration into standard tool posts and fast changeover Designed around a 20×20 mm shank and an overall length of 125 mm, the holder fits most standard tool posts and quick‑change systems without additional adapters. Compatibility with Horn inserts (ISO designation 2020) and the shank identification 5C‑R S224 simplifies spare‑part management and reduces setup time when changing inserts. The compact geometry supports straightforward clamping and repeatable positioning, which helps workshops decrease non‑productive time and maintain steady cycle times on short‑run and batch production. Balanced handling and dependable workshop performance At approximately 0.401 kg, the holder offers a balance between rigidity and manageable handling during setup. Its geometry provides a rigid seat for the insert while remaining light enough for safe manual handling and alignment. Supplied through Metav’s distribution network, the product benefits from Metav’s quality filtering—which translates into consistent warehouse checks and reliable availability for European workshops—backing the tool with decades of metrology and tooling expertise. For reliable right‑hand parting performance and rapid availability, contact Metav Werkzeuge for technical advice and ordering support — Metav’s specialists will confirm suitability for the intended machine setup and inserts Technical data Article number: D708TM SKU: D708TM Manufacturer: Teknik Makina Dimensions & mass Overall length: 125 mm Shank height: 20 mm Head width: 20 mm Holder width: 20 mm Cutting width: 5 mm Max plunge depth: 18 mm Weight: 0.401 kg Compatibility / Features Cutting direction: right Compatible with: Horn inserts ISO designation: 2020 Shank designation: 5C‑R S224 FAQ What machine types suit this parting holder? The D708TM parting tool holder from Teknik Makina is intended for engine lathes and CNC turning centres that accept a 20×20 mm shank and can accommodate right‑hand parting operations. Which inserts fit the holder? The holder accepts Horn inserts with an ISO 2020 seat; use accordingly sized 2020 style inserts to ensure correct seating and clamping with the D708TM. How deep can the tool plunge safely? Maximum plunge or cutting depth is 18 mm; adhere to machine and insert manufacturer limits for material and application to maintain tool life and workpiece quality. Is the D708TM suitable for finishing the parted surface? The holder is designed for reliable parting; surface finish after parting depends on insert geometry and cutting parameters rather than the holder alone—select appropriate inserts and feeds for improved finish when using the D708TM. What does right‑hand cutting mean in practice? Right‑hand indicates the cutting edge advances from the right relative to the tool orientation on the lathe; the D708TM is manufactured for this direction and should be mounted accordingly to achieve the specified cutting behaviour. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com
125mm Steck Clamping Holder for KGMN 200 Indexable Inserts 16mm Width, Left-Hand - Teknik Makina
Take advantage of a compact, purpose-built clamp holder that combines secure clamping for indexable inserts with a space-saving 125 mm overall length; its left-hand cutting orientation and compatibility with KGMN 200 inserts support reliable parting operations—order directly via Metav Werkzeuge or ask the consultants for application advice. Stechklemmhalter clamp holder for KGMN 200 indexable inserts — 125 mm, left-hand cutting (Teknik Makina) Stechklemmhalter is a robust clamp holder designed for precise parting and grooving with KGMN 200 indexable inserts in left-hand turning applications. Left-hand cutting orientation for counter-facing cuts Compatible with KGMN 200 indexable inserts Compact overall length 125 mm for tight set-ups 16 x 16 mm shank for standard toolposts Precision clamping for consistent parting results A purpose-designed clamp holder provides steady and repeatable performance when parting or grooving. The secure clamp system holds KGMN 200 indexable inserts firmly, minimising vibrations that lead to poor surface finish or premature insert wear. By stabilising the cutting edge, the holder improves process reliability and reduces scrap rates, making it a sensible choice where dimensional accuracy matters. The holder’s left-hand orientation is compatible with counter-facing operations commonly required in turning shops. Compact dimensions that simplify machine setup The holder’s 125 mm overall length and compact 16 x 16 mm shank are tailored for installations where space is at a premium. A smaller footprint allows closer tool proximity on multi-station turrets and reduces interference with adjacent tooling, which can speed up setup changes and increase turret utilisation. The narrow cutting-head width further aids accessibility in confined grooves, supporting efficient workflows in batch production and prototyping alike. Robust fastening and maintenance-friendly design Designed for secure fixing, the clamp holder uses a T15 Torx interface and an M4x12.5 fastening screw to deliver repeatable clamping torque and simple servicing. The standardised fastener interfaces facilitate quick insert changes and maintenance with widely available tools, reducing machine downtime. Reliable clamping prevents insert movement under load, which in turn prolongs insert life and ensures consistent cutting performance over longer runs. Suitable for industrial turning environments Built for compatibility with inserts from established manufacturers such as Korloy, this toolholder supports straightforward tool standardisation across a workshop. The combination of compact geometry, secure clamp action and industry-standard interfaces makes it a practical choice for metalworking shops that prioritise predictable results and efficient changeovers. Its specification supports common applications in grooving and parting across a variety of ferrous and non-ferrous turning tasks. Request a tailored quote from Metav Werkzeuge for this Teknik Makina clamp holder, optimised for KGMN 200 applications, and receive expert advice on integration and supply. Technical data Article number: D059TM Manufacturer: Teknik Makina Product type: Stechklemmhalter (clamp holder) Compatible inserts: KGMN 200 Facts Overall length: 125 mm Weight: 0.267 kg Shank width: 16 mm Shank height: 16 mm Special features Cutting-head width: 16.2 mm Maximum plunging depth: 16 mm Cutting width: 2 mm Cutting direction: left Fastening screw: M4x12.5 Torx key: T15 Compatible insert manufacturer: Korloy ISO shank designation: 1616 FAQ What insert type fits this clamp holder? The clamp holder is designed for KGMN 200 indexable inserts and is compatible with inserts from Korloy. Is the holder suitable for left-hand turning only? Yes, the toolholder’s geometry and clamping orientation are specified for left-hand cutting applications. How is the insert secured in the holder? Insert clamping is achieved using the supplied fastening screw (M4x12.5) tightened with a T15 Torx key to ensure secure, repeatable clamping. Can this holder be used in compact turret layouts? The holder’s 125 mm length and 16 x 16 mm shank are ideal for tight set-ups and multi-tool turrets where space is limited. What is the article number for ordering? The SKU for ordering is D059TM; reference this when enquiring with Metav Werkzeuge. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com
125mm Turning Clamp Holder Left 20x20mm Cutting Width 4mm, Max Cut Depth 18mm - Teknik Makina
Thanks to its ISO 2020 shank and left-hand cutting orientation, this parting clamp holder delivers stable, repeatable parting and grooving operations with a maximum cutting depth of 18 mm; its 125 mm overall length provides added rigidity for cleaner separations. Order the holder directly via Metav Werkzeuge or consult our specialists for application-specific advice. Parting clamp holder L125mm — left-hand, ISO 2020, Teknik Makina The parting clamp holder L125mm is a left-hand lathe holder designed for precise parting and grooving tasks in small-batch and industrial turning applications. ISO 2020 compatible 20×20 shank Left-hand cutting orientation Max parting depth 18 mm 4 mm cutting width for narrow grooves Stability and compatibility for consistent parting The holder is built around the ISO 2020 format and a 20 × 20 mm shank, which ensures immediate compatibility with common toolposts and quick-change systems. This standardised geometry reduces set-up time and minimises adapter needs, so production runs benefit from faster changeovers. The combination of the 125 mm overall length and the compact cross-section provides a balance between reach and stiffness, which helps to reduce vibration and maintain a clean parting surface. Secure clamping and repeatable set-ups A robust M5×20 clamping screw secures the insert and is tightened using a 4 mm Allen key, enabling straightforward installation and reliable retention during cut-off operations. The tool is specified with a 4 mm cutting width, tailored for slender parting inserts and narrow groove profiles. The clamping arrangement is designed for repeatable setups, so once zeroed-in, the holder will maintain alignment across consecutive operations, reducing scrap and rework. Practical application and workshop fit Engineered for lathe parting and grooving, the holder supports left-hand parting routines where the cut progresses from the outside towards the chuck. With a maximum cutting depth of 18 mm, it suits operations that require deeper separations without compromising control. The component's modest mass and compact footprint make it suitable for both bench-mounted toolposts in small workshops and production lathes in larger shops. For complex requirements or material-specific guidance, Metav Werkzeuge provides technical advice and availability information. For precise parting solutions from Teknik Makina, contact Metav Werkzeuge in Emmerich for stock checks and expert application guidance at info@metav-werkzeuge.com or +49 2822 7131930 Technical data Article number: D888TM eClass: 21181005 Product type: Parting clamp holder Brand: Teknik Makina Facts Overall length: 125 mm Weight: 0.401 kg Clamping width: 20 mm Clamping height: 20 mm Cutting-head width: 20 mm Cutting width: 4 mm Max parting depth: 18 mm Cutting direction: left Clamping screw: M5×20 Hex key: 4 mm Allen Special features ISO designation: 2020 Label: L125mm SKU: D888TM FAQ What is the maximum cutting depth of this holder? The holder provides a maximum parting depth of 18 mm, suitable for deeper cut-off operations with appropriate inserts. Which cutting direction does the holder support? This parting clamp holder is configured for left-hand cutting, making it suitable where the tool cuts towards the chuck. What shank and clamping size does the holder use? The tool uses a 20 × 20 mm shank in accordance with the ISO 2020 specification for compatibility with standard toolposts. Which screw and key are required to secure the insert? Insert clamping is achieved with an M5×20 screw, tightened with a 4 mm Allen key as specified. Is this holder suitable for workshop and production lathes? Yes — the combination of a 125 mm overall length and standard shank format makes it suitable for small workshops and larger production lathes where left-hand parting is required. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com
125mm Turning Clamp Holder Left 2mm Cutting Width 16mm Max Cut Depth - Teknik Makina
Robust clamping and a compact 125 mm profile enable precise narrow‑kerf parting with minimal overhang. The ISO 1212 12 x 12 mm shank and left‑hand orientation provide consistent set‑up in standard tool posts, reducing vibration and improving surface finish. Order the parting tool holder via Metav Werkzeuge or consult our specialists for application advice. Stechklemmhalter L125mm – left-hand parting tool holder, ISO 1212, 12 x 12 mm (Teknik Makina) The Stechklemmhalter L125mm is a left‑hand parting tool holder engineered for accurate parting and grooving operations on lathes with a 12 x 12 mm tool post, offering compact rigidity for short overhang setups. Left-hand cutting direction ISO 1212 clamping size 12 x 12 mm Max parting depth 16 mm Includes M5x16 clamping screw and 4 mm Allen key Stable clamping for repeatable parting quality The compact holder combines a short overall length with a 12 x 12 mm shank to reduce overhang and increase rigidity, which directly improves cutting stability. With the ISO 1212 designation, the tool fits common tool posts and quick‑change systems that accept 12 × 12 holders, making integration straightforward. The reduced vibration from a shorter projection encourages more consistent tool life and cleaner parting surfaces, translating into fewer reworks and higher throughput for repetitive turning tasks. Simple set-up and secure fixation for production environments Designed for efficient workshop use, the holder includes a M5x16 clamping screw and a 4 mm Allen key for secure fastening of the parting blade. The compact mass and 125 mm overall length keep the centre of gravity close to the tool post, helping to maintain alignment during aggressive cuts. Minimal assembly time and reliable clamping mean faster changeovers between jobs and consistent position retention across batches, supporting smoother production cycles. Narrow kerf capability and application guidance The holder accepts a 2 mm cutting width blade and permits a 16 mm max parting depth, enabling narrow‑kerf operations where material savings and chip control are priorities. The left‑hand orientation is intended for cuts where the tool approaches the workpiece from the operator’s right side or for specific machine set‑ups that require left‑hand tool geometry. For applications requiring alternative blade widths or deeper cuts, matching the holder dimensions to the tool post and machining strategy is essential to maintain rigidity and safety. Choose the Teknik Makina left‑hand parting holder for stable, narrow‑kerf turning tasks — contact Metav Werkzeuge for procurement guidance or technical consultation at +49 2822 7131930 or info@metav-werkzeuge.com Technical data SKU: D880TM Label: Stechklemmhalter L125mm Manufacturer: Teknik Cutting Tools Overall length: 125 mm Weight: 0.166 kg Shank width: 12 mm Shank height: 12 mm Cutting head width: 12 mm Max parting depth: 16 mm Cutting width: 2 mm ISO designation: 1212 Cutting direction: left Clamping screw: M5x16 Allen key: 4 mm FAQ What is the shank size and mounting standard of the holder? The holder uses a 12 x 12 mm shank and conforms to the ISO 1212 style mounting, ensuring compatibility with tool posts and systems designed for 12 × 12 holders. Which cutting blade width fits the Stechklemmhalter L125mm? The Stechklemmhalter L125mm is specified for a 2 mm cutting width and secures parting blades with the supplied M5x16 screw. How deep can the tool cut in a single pass? Maximum parting or grooving depth is 16 mm as stated for this tool holder; actual depth depends on blade geometry and machine rigidity. What does 'left‑hand cutting direction' mean for set-up? Left‑hand cutting means the tool is intended for cuts where the cutting edge advances in a left‑hand orientation relative to the spindle rotation; it should be mounted accordingly to achieve the correct chip flow and clearance. Is the clamping hardware included for immediate use? Yes, the holder is supplied with the M5x16 clamping screw and a 4 mm Allen key for immediate assembly and secure clamping of the parting blade. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com
125mm Turning Tool Holder Steep Clamp Holder 2mm Cutting Width Left 16mm Cutting Depth - Teknik Makina
Benefit from a compact, workshop‑ready parting solution combining a 20 × 20 mm tool shank interface with a 125 mm overall length for extended reach and a maximum parting depth of 16 mm; order via Metav Werkzeuge or contact our consultants for application advice. Parting tool clamp holder L125mm – left‑hand, 20 × 20 mm shank (Teknik Makina) The Parting tool clamp holder L125mm is a left‑hand parting holder designed for turning operations where secure clamping and precise depth control are required, compatible with standard 20 × 20 mm tool posts. Left‑hand cutting orientation 20 × 20 mm tool shank compatible 125 mm overall length for reach Max parting depth 16 mm, 2 mm blade width Secure clamping that keeps cuts true A rigid clamping interface is essential for accurate parting; this holder is built around the 20 × 20 mm standard and the ISO 2020 designation, which ensures compatibility with common tool posts and fixtures. The integrated M6×20 clamping screw secures the blade reliably, reducing vibration and enabling repeatable cuts. That translates into fewer reworks and steadier process control when performing routine parting and grooving tasks in production work. Predictable cutting performance for process planning When process planners require quantifiable limits, the holder delivers a maximum parting depth of 16 mm with a nominal 2 mm blade width, enabling clear decisions about tool selection and cycle planning. The left‑hand cutting orientation is specified for use where the tool approaches the workpiece from the appropriate side; this simple characteristic removes ambiguity during fixture setup and helps maintain consistent surface finish and dimensional control across batches. Compact design for workshop flexibility With an overall length of 125 mm and a mass of approximately 0.401 kg, the holder is compact yet practical for tight toolpost arrangements and multi‑tool turrets. The included 5 mm Allen key specification and the standard clamping screw type mean familiar workshop tooling is sufficient for assembly and adjustments. Such practical dimensions and familiar fastenings reduce setup time and simplify maintenance routines on the shop floor. Practical integration and application guidance The holder is intended for conventional turning operations requiring a clamp‑style parting solution and fits into established tool inventories thanks to its standard dimensions and ISO alignment. For tasks bordering the holder’s limits—deeper parting, unusual alloys or interrupted cuts—consultation is recommended to match blade geometry and cutting data. Metav’s product expertise and technical resources support selection and ensure the holder is deployed where it contributes to stable productivity. Contact Metav Werkzeuge for tailored application advice and specify SKU D882TM when enquiring to ensure fast, precise support from our specialists. Technical Data Article number: D882TM ECLASS: 21181005 Label: Parting tool clamp holder L125mm SKU: D882TM Facts Overall length: 125 mm Weight: 0.401 kg Holder width: 20 mm Holder height: 20 mm Cutting head width: 20 mm Max parting depth: 16 mm Cutting width: 2 mm Special features Left‑hand cutting direction ISO 2020 size (20 × 20 mm) M6×20 clamping screw 5 mm Allen key specification SKU for reference: D882TM FAQ Which toolpost size is compatible with this holder? The holder accepts the standard 20 × 20 mm tool shank (ISO 2020), making it compatible with common toolposts and fixtures used for parting operations. What maximum parting depth can be achieved? This parting clamp holder supports a maximum parting depth of 16 mm with a nominal blade width of 2 mm. Is the holder for left‑hand or right‑hand cutting? The unit is specified for left‑hand cutting orientation; this is noted on the product data for correct mounting and use. What are the overall length and mass of the holder? The overall length is 125 mm and the weight is approximately 0.401 kg, suitable for compact setups and standard turret tooling. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com
Fast, reliable parting and grooving for precision turning
Parting and grooving tools, also referred to as parting blades, grooving tools or cut-off tools, are narrow carrier tools for lathes fitted with replaceable carbide inserts. Supplied as solid holders or flat blades, they are designed to cut precise grooves and to part finished components cleanly from the material bar.
Why internal coolant matters for deep cuts and tough materials
When used in simple form without internal coolant, the cutting fluid is applied via external machine nozzles; this is often sufficient for very shallow grooves and easily machinable materials. For deeper grooving and parting operations, however, the tool nearly encloses the slot so that external coolant cannot reach the cutting edge. Tools with internal coolant incorporate fine, integrated channels that deliver coolant under high pressure directly to the insert and beneath the chip. This targeted supply controls the intense heat in the confined cutting zone and uses flushing pressure to eject chips reliably, preventing chip jamming, surface damage and sudden tool breakage.
Clear operational benefits you can measure
- faster cycle times through reliable chip evacuation and uninterrupted cutting
- extended tool life thanks to effective heat control at the cutting edge
- consistent surface finish by avoiding chip re-cutting and scarring
- safer machining of hard or ductile materials due to reduced risk of tool fracture
- simplified setup when holders with integrated channels replace complex external coolant rigs
Metav as a practical partner for your workshop
Metav stands for democratisation of precision: decades of expertise, a quality filter in Emmerich and an assortment that supports industry and trade. With more than 48,000 customers and a catalogue of over 250,000 products, Metav provides a focused selection of parting and grooving tools, accessories and matched holders so that procurement and technical choice remain straightforward and dependable.
Parting and grooving tools bring reliable groove geometry and safe parting to turning operations; choosing holders with integrated coolant channels is essential for deep cuts and demanding materials. If technical advice is needed, Metav’s product specialists can help select the appropriate tool geometry and coolant configuration for the application.
FAQ
When is internal coolant necessary for parting tools?
Internal coolant becomes necessary for deep grooving and parting or when machining hard or ductile materials; it delivers coolant directly to the insert and beneath the chip, which is critical when external nozzles can no longer reach the cutting edge.
Can parting tools be used without internal coolant?
Yes — for very shallow cuts and easily machinable materials, parting tools can be used with external machine coolant nozzles, but performance and tool life will drop markedly for deeper cuts.
How do parting tools prevent dangerous chip jamming?
Parting tools with integrated channels use high-pressure coolant to flush chips out of the narrow slot, preventing chips from becoming trapped and minimising the risk of surface damage and abrupt tool failure.
What should be considered when choosing a grooving insert and holder?
Select a combination that matches the required groove depth and material grade; holders offering integrated high-pressure channels are preferred for deep cuts or poor-chip-breaking materials to ensure heat control and reliable chip evacuation.
Fragen zu diesen Produkten??
Mit mehr als 30 Jahren Erfahrung beraten wir Sie gerne persönlich.
Tel.: +49 2822 7131930
Mail: info@metav-werkzeuge.com